Re: [PATCH v2 3/3] arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 13/03/2024 13:30, Sumit Garg wrote:
> Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge
> Box Core board based on the Qualcomm APQ8016E SoC.
> 

...

> +
> +/ {
> +	model = "Schneider Electric HMIBSC Board";
> +	compatible = "schneider,apq8016-hmibsc", "qcom,apq8016";
> +
> +	aliases {
> +		mmc0 = &sdhc_1; /* eMMC */
> +		mmc1 = &sdhc_2; /* SD card */
> +		serial0 = &blsp_uart1;
> +		serial1 = &blsp_uart2;
> +		usid0 = &pm8916_0;
> +		i2c1 = &blsp_i2c6;
> +		i2c3 = &blsp_i2c4;
> +		i2c4 = &blsp_i2c3;

The aliases should match schematics of the board, so I assume missing
i2c2 is intentional, right?

> +		spi0 = &blsp_spi5;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	memory@80000000 {
> +		reg = <0 0x80000000 0 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		ramoops@bff00000 {
> +			compatible = "ramoops";
> +			reg = <0x0 0xbff00000 0x0 0x100000>;
> +
> +			record-size = <0x20000>;
> +			console-size = <0x20000>;
> +			ftrace-size = <0x20000>;
> +		};
> +	};
> +
> +	usb2513 {

Node names should be generic. See also an explanation and list of
examples (not exhaustive) in DT specification:
https://devicetree-specification.readthedocs.io/en/latest/chapter2-devicetree-basics.html#generic-names-recommendation
e.g. usb-hub



> +		compatible = "smsc,usb3503";
> +		reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>;
> +		initial-mode = <1>;
> +	};
> +
> +	usb_id: usb-id {
> +		compatible = "linux,extcon-usb-gpio";
> +		id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&usb_id_default>;
> +	};
> +
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&adv7533_out>;
> +			};
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		autorepeat;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&msm_key_volp_n_default>;
> +
> +		button {
> +			label = "Volume Up";
> +			linux,code = <KEY_VOLUMEUP>;
> +			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	leds {
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pm8916_mpps_leds>;

First property is always compatible. Please apply DTS coding style rules.

> +
> +		compatible = "gpio-leds";
> +		#address-cells = <1>;
> +		#size-cells = <0>;

That's not a bus.

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check W=1` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +
> +		led@5 {
> +			reg = <5>;
> +			label = "apq8016-hmibsc:green:wlan";
> +			function = LED_FUNCTION_WLAN;
> +			color = <LED_COLOR_ID_YELLOW>;
> +			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "phy0tx";
> +			default-state = "off";
> +		};
> +
> +		led@6 {
> +			reg = <6>;
> +			label = "apq8016-hmibsc:yellow:bt";
> +			function = LED_FUNCTION_BLUETOOTH;
> +			color = <LED_COLOR_ID_BLUE>;
> +			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "bluetooth-power";
> +			default-state = "off";
> +		};
> +	};
> +};
> +
> +&blsp_i2c3 {
> +	status = "okay";
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c32";
> +		reg = <0x50>;
> +	};
> +};
> +
> +&blsp_i2c4 {
> +	status = "okay";
> +
> +	adv_bridge: bridge@39 {
> +		status = "okay";

Why do you need it? Was it disabled?

And why this is before compatible? If this stays, please use DTS coding
style rules for placement.

> +
> +		compatible = "adi,adv7533";
> +		reg = <0x39>;
> +
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
> +
> +		adi,dsi-lanes = <4>;
> +		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
> +		clock-names = "cec";
> +
> +		pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
> +
> +		avdd-supply = <&pm8916_l6>;
> +		a2vdd-supply = <&pm8916_l6>;
> +		dvdd-supply = <&pm8916_l6>;
> +		pvdd-supply = <&pm8916_l6>;
> +		v1p2-supply = <&pm8916_l6>;
> +		v3p3-supply = <&pm8916_l17>;
> +
> +		pinctrl-names = "default","sleep";
> +		pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
> +		pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
> +		#sound-dai-cells = <1>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				adv7533_in: endpoint {
> +					remote-endpoint = <&mdss_dsi0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				adv7533_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&blsp_i2c6 {
> +	status = "okay";
> +
> +	rtc@30 {
> +		compatible = "sii,s35390a";
> +		reg = <0x30>;
> +	};
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c256";
> +		reg = <0x50>;
> +	};
> +};
> +
> +&blsp_spi5 {
> +	status = "okay";
> +	cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
> +
> +	tpm@0 {
> +		compatible = "tcg,tpm_tis-spi";
> +		reg = <0>;
> +		spi-max-frequency = <500000>;
> +	};
> +};
> +
> +&blsp_uart1 {
> +	status = "okay";
> +	label = "UART0";
> +};
> +
> +&blsp_uart2 {
> +	status = "okay";
> +	label = "UART1";
> +};
> +
> +&lpass {
> +	status = "okay";
> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_dsi0_out {
> +	data-lanes = <0 1 2 3>;
> +	remote-endpoint = <&adv7533_in>;
> +};
> +
> +&pm8916_codec {
> +	status = "okay";
> +	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
> +	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
> +};
> +
> +&pm8916_resin {
> +	status = "okay";
> +	linux,code = <KEY_POWER>;
> +};
> +
> +&pm8916_rpm_regulators {
> +	pm8916_l17: l17 {
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +};
> +
> +&sdhc_1 {
> +	status = "okay";
> +};
> +
> +&sdhc_2 {
> +	status = "okay";
> +
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
> +	pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
> +
> +	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
> +};
> +
> +&sound {
> +	status = "okay";

Is thi sneeded?

> +
> +	pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
> +	pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
> +	pinctrl-names = "default", "sleep";
> +	model = "DB410c";
> +	audio-routing =
> +		"AMIC2", "MIC BIAS Internal2",
> +		"AMIC3", "MIC BIAS External1";
> +
> +	quaternary-dai-link {
> +		link-name = "ADV7533";
> +		cpu {
> +			sound-dai = <&lpass MI2S_QUATERNARY>;
> +		};
> +		codec {
> +			sound-dai = <&adv_bridge 0>;
> +		};
> +	};
> +
> +	primary-dai-link {
> +		link-name = "WCD";
> +		cpu {
> +			sound-dai = <&lpass MI2S_PRIMARY>;
> +		};
> +		codec {
> +			sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
> +		};
> +	};
> +
> +	tertiary-dai-link {
> +		link-name = "WCD-Capture";
> +		cpu {
> +			sound-dai = <&lpass MI2S_TERTIARY>;
> +		};
> +		codec {
> +			sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
> +		};
> +	};
> +};
> +
> +&usb {
> +	status = "okay";
> +	extcon = <&usb_id>, <&usb_id>;
> +
> +	pinctrl-names = "default", "device";
> +	pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
> +	pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
> +};
> +
> +&usb_hs_phy {
> +	extcon = <&usb_id>;
> +};
> +
> +&wcnss {
> +	status = "okay";
> +	firmware-name = "qcom/apq8016/wcnss.mbn";
> +};
> +
> +&wcnss_ctrl {
> +	firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
> +};
> +
> +&wcnss_iris {
> +	compatible = "qcom,wcn3620";
> +};
> +
> +&wcnss_mem {
> +	status = "okay";
> +};
> +
> +/* Enable CoreSight */
> +&cti0 { status = "okay"; };
> +&cti1 { status = "okay"; };
> +&cti12 { status = "okay"; };
> +&cti13 { status = "okay"; };
> +&cti14 { status = "okay"; };
> +&cti15 { status = "okay"; };
> +&debug0 { status = "okay"; };
> +&debug1 { status = "okay"; };
> +&debug2 { status = "okay"; };
> +&debug3 { status = "okay"; };
> +&etf { status = "okay"; };
> +&etm0 { status = "okay"; };
> +&etm1 { status = "okay"; };
> +&etm2 { status = "okay"; };
> +&etm3 { status = "okay"; };
> +&etr { status = "okay"; };
> +&funnel0 { status = "okay"; };
> +&funnel1 { status = "okay"; };
> +&replicator { status = "okay"; };
> +&stm { status = "okay"; };
> +&tpiu { status = "okay"; };
> +
> +/*
> + * 2mA drive strength is not enough when connecting multiple
> + * I2C devices with different pull up resistors.
> + */
> +
> +&blsp_i2c4_default {

None of your overrides look like have proper alphabetical order. Please
use alphabetical order.



Best regards,
Krzysztof