* [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support
@ 2012-10-19 2:19 Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <1350613168-22689-1-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-10-19 2:19 UTC (permalink / raw)
To: linux-arm-kernel
Cc: Nicolas Ferre, devicetree-discuss,
Jean-Christophe PLAGNIOL-VILLARD
CPU Module with ATMEL AT91SAM9G45
http://www.ronetix.at/pm9g45.html
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 145 insertions(+)
create mode 100644 arch/arm/boot/dts/pm9g45.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a9b051a..627b6ad 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
# sam9g45
dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
# sam9n12
dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
# sam9x5
diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
new file mode 100644
index 0000000..b0c258d
--- /dev/null
+++ b/arch/arm/boot/dts/pm9g45.dts
@@ -0,0 +1,144 @@
+/*
+ * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+/include/ "at91sam9g45.dtsi"
+
+/ {
+ model = "Ronetix pm9g45";
+ compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ reg = <0x70000000 0x8000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock@0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial@ffffee00 {
+ status = "okay";
+ };
+
+ pinctrl@fffff200 {
+
+ board {
+ pinctrl_board_nand: nand0-board {
+ atmel,pins =
+ <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/
+ 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
+ };
+ };
+ };
+
+ macb0: ethernet@fffbc000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ pinctrl-0 = <&pinctrl_board_nand>;
+
+ gpios = <&pioD 3 0
+ &pioC 14 0
+ 0
+ >;
+
+ status = "okay";
+
+ at91bootstrap@0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ barebox@20000 {
+ label = "barebox";
+ reg = <0x20000 0x40000>;
+ };
+
+ bareboxenv@60000 {
+ label = "bareboxenv";
+ reg = <0x60000 0x1A0000>;
+ };
+
+ kernel@200000 {
+ label = "bareboxenv2";
+ reg = <0x200000 0x300000>;
+ };
+
+ kernel@500000 {
+ label = "root";
+ reg = <0x500000 0x400000>;
+ };
+
+ data@900000 {
+ label = "data";
+ reg = <0x900000 0x8340000>;
+ };
+ };
+
+ usb0: ohci@00700000 {
+ status = "okay";
+ num-ports = <2>;
+ };
+
+ usb1: ehci@00800000 {
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ label = "led0";
+ gpios = <&pioD 0 1>;
+ linux,default-trigger = "nand-disk";
+ };
+
+ led1 {
+ label = "led1";
+ gpios = <&pioD 31 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ right {
+ label = "SW4";
+ gpios = <&pioE 7 1>;
+ linux,code = <106>;
+ };
+
+ up {
+ label = "SW3";
+ gpios = <&pioE 8 1>;
+ linux,code = <103>;
+ };
+ };
+};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 4+ messages in thread[parent not found: <1350613168-22689-1-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>]
* Re: [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support [not found] ` <1350613168-22689-1-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> @ 2012-11-16 13:08 ` Nicolas Ferre [not found] ` <50A63AEA.2000706-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> 0 siblings, 1 reply; 4+ messages in thread From: Nicolas Ferre @ 2012-11-16 13:08 UTC (permalink / raw) To: Jean-Christophe PLAGNIOL-VILLARD Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD : > CPU Module with ATMEL AT91SAM9G45 > http://www.ronetix.at/pm9g45.html > > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> > Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> Ok, queued in at91-3.8-dt branch. I had to modify the Makefile part of it to match current move to arch/arm/boot/dts/Makefile. Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++ > 2 files changed, 145 insertions(+) > create mode 100644 arch/arm/boot/dts/pm9g45.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index a9b051a..627b6ad 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb > dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb > # sam9g45 > dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb > +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb > # sam9n12 > dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb > # sam9x5 > diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts > new file mode 100644 > index 0000000..b0c258d > --- /dev/null > +++ b/arch/arm/boot/dts/pm9g45.dts > @@ -0,0 +1,144 @@ > +/* > + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board > + * > + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> > + * > + * Licensed under GPLv2. > + */ > +/dts-v1/; > +/include/ "at91sam9g45.dtsi" > + > +/ { > + model = "Ronetix pm9g45"; > + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; > + > + chosen { > + bootargs = "console=ttyS0,115200"; > + }; > + > + memory { > + reg = <0x70000000 0x8000000>; > + }; > + > + clocks { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + main_clock: clock@0 { > + compatible = "atmel,osc", "fixed-clock"; > + clock-frequency = <12000000>; > + }; > + }; > + > + ahb { > + apb { > + dbgu: serial@ffffee00 { > + status = "okay"; > + }; > + > + pinctrl@fffff200 { > + > + board { > + pinctrl_board_nand: nand0-board { > + atmel,pins = > + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/ > + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ > + }; > + }; > + }; > + > + macb0: ethernet@fffbc000 { > + phy-mode = "rmii"; > + status = "okay"; > + }; > + }; > + > + nand0: nand@40000000 { > + nand-bus-width = <8>; > + nand-ecc-mode = "soft"; > + nand-on-flash-bbt; > + pinctrl-0 = <&pinctrl_board_nand>; > + > + gpios = <&pioD 3 0 > + &pioC 14 0 > + 0 > + >; > + > + status = "okay"; > + > + at91bootstrap@0 { > + label = "at91bootstrap"; > + reg = <0x0 0x20000>; > + }; > + > + barebox@20000 { > + label = "barebox"; > + reg = <0x20000 0x40000>; > + }; > + > + bareboxenv@60000 { > + label = "bareboxenv"; > + reg = <0x60000 0x1A0000>; > + }; > + > + kernel@200000 { > + label = "bareboxenv2"; > + reg = <0x200000 0x300000>; > + }; > + > + kernel@500000 { > + label = "root"; > + reg = <0x500000 0x400000>; > + }; > + > + data@900000 { > + label = "data"; > + reg = <0x900000 0x8340000>; > + }; > + }; > + > + usb0: ohci@00700000 { > + status = "okay"; > + num-ports = <2>; > + }; > + > + usb1: ehci@00800000 { > + status = "okay"; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led0 { > + label = "led0"; > + gpios = <&pioD 0 1>; > + linux,default-trigger = "nand-disk"; > + }; > + > + led1 { > + label = "led1"; > + gpios = <&pioD 31 0>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + right { > + label = "SW4"; > + gpios = <&pioE 7 1>; > + linux,code = <106>; > + }; > + > + up { > + label = "SW3"; > + gpios = <&pioE 8 1>; > + linux,code = <103>; > + }; > + }; > +}; > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 4+ messages in thread
[parent not found: <50A63AEA.2000706-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>]
* Re: [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support [not found] ` <50A63AEA.2000706-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> @ 2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD [not found] ` <20121116132819.GG4398-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org> 0 siblings, 1 reply; 4+ messages in thread From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-16 13:28 UTC (permalink / raw) To: Nicolas Ferre Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r On 14:08 Fri 16 Nov , Nicolas Ferre wrote: > On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD : > > CPU Module with ATMEL AT91SAM9G45 > > http://www.ronetix.at/pm9g45.html > > > > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> > > Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> > > Ok, queued in at91-3.8-dt branch. > > I had to modify the Makefile part of it to match current move to > arch/arm/boot/dts/Makefile. > > Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> I prefer to go via linus W I've other updte for the macb on the top of it ditto for the rm9200 Best Regards, J. > > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++ > > 2 files changed, 145 insertions(+) > > create mode 100644 arch/arm/boot/dts/pm9g45.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index a9b051a..627b6ad 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb > > dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb > > # sam9g45 > > dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb > > +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb > > # sam9n12 > > dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb > > # sam9x5 > > diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts > > new file mode 100644 > > index 0000000..b0c258d > > --- /dev/null > > +++ b/arch/arm/boot/dts/pm9g45.dts > > @@ -0,0 +1,144 @@ > > +/* > > + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board > > + * > > + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> > > + * > > + * Licensed under GPLv2. > > + */ > > +/dts-v1/; > > +/include/ "at91sam9g45.dtsi" > > + > > +/ { > > + model = "Ronetix pm9g45"; > > + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; > > + > > + chosen { > > + bootargs = "console=ttyS0,115200"; > > + }; > > + > > + memory { > > + reg = <0x70000000 0x8000000>; > > + }; > > + > > + clocks { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + ranges; > > + > > + main_clock: clock@0 { > > + compatible = "atmel,osc", "fixed-clock"; > > + clock-frequency = <12000000>; > > + }; > > + }; > > + > > + ahb { > > + apb { > > + dbgu: serial@ffffee00 { > > + status = "okay"; > > + }; > > + > > + pinctrl@fffff200 { > > + > > + board { > > + pinctrl_board_nand: nand0-board { > > + atmel,pins = > > + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/ > > + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ > > + }; > > + }; > > + }; > > + > > + macb0: ethernet@fffbc000 { > > + phy-mode = "rmii"; > > + status = "okay"; > > + }; > > + }; > > + > > + nand0: nand@40000000 { > > + nand-bus-width = <8>; > > + nand-ecc-mode = "soft"; > > + nand-on-flash-bbt; > > + pinctrl-0 = <&pinctrl_board_nand>; > > + > > + gpios = <&pioD 3 0 > > + &pioC 14 0 > > + 0 > > + >; > > + > > + status = "okay"; > > + > > + at91bootstrap@0 { > > + label = "at91bootstrap"; > > + reg = <0x0 0x20000>; > > + }; > > + > > + barebox@20000 { > > + label = "barebox"; > > + reg = <0x20000 0x40000>; > > + }; > > + > > + bareboxenv@60000 { > > + label = "bareboxenv"; > > + reg = <0x60000 0x1A0000>; > > + }; > > + > > + kernel@200000 { > > + label = "bareboxenv2"; > > + reg = <0x200000 0x300000>; > > + }; > > + > > + kernel@500000 { > > + label = "root"; > > + reg = <0x500000 0x400000>; > > + }; > > + > > + data@900000 { > > + label = "data"; > > + reg = <0x900000 0x8340000>; > > + }; > > + }; > > + > > + usb0: ohci@00700000 { > > + status = "okay"; > > + num-ports = <2>; > > + }; > > + > > + usb1: ehci@00800000 { > > + status = "okay"; > > + }; > > + }; > > + > > + leds { > > + compatible = "gpio-leds"; > > + > > + led0 { > > + label = "led0"; > > + gpios = <&pioD 0 1>; > > + linux,default-trigger = "nand-disk"; > > + }; > > + > > + led1 { > > + label = "led1"; > > + gpios = <&pioD 31 0>; > > + linux,default-trigger = "heartbeat"; > > + }; > > + }; > > + > > + gpio_keys { > > + compatible = "gpio-keys"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + right { > > + label = "SW4"; > > + gpios = <&pioE 7 1>; > > + linux,code = <106>; > > + }; > > + > > + up { > > + label = "SW3"; > > + gpios = <&pioE 8 1>; > > + linux,code = <103>; > > + }; > > + }; > > +}; > > > > > -- > Nicolas Ferre ^ permalink raw reply [flat|nested] 4+ messages in thread
[parent not found: <20121116132819.GG4398-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org>]
* Re: [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support [not found] ` <20121116132819.GG4398-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org> @ 2012-11-16 13:32 ` Nicolas Ferre 0 siblings, 0 replies; 4+ messages in thread From: Nicolas Ferre @ 2012-11-16 13:32 UTC (permalink / raw) To: Jean-Christophe PLAGNIOL-VILLARD Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r On 11/16/2012 02:28 PM, Jean-Christophe PLAGNIOL-VILLARD : > On 14:08 Fri 16 Nov , Nicolas Ferre wrote: >> On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD : >>> CPU Module with ATMEL AT91SAM9G45 >>> http://www.ronetix.at/pm9g45.html >>> >>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> >>> Cc: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> >> >> Ok, queued in at91-3.8-dt branch. >> >> I had to modify the Makefile part of it to match current move to >> arch/arm/boot/dts/Makefile. >> >> Acked-by: Nicolas Ferre <nicolas.ferre-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org> > I prefer to go via linus W I've other updte for the macb on the top of it Fine... Be careful about macb, there are many things happening right now in net-next for this interface! > ditto for the rm9200 Noted. Thanks. Bye, >>> --- >>> arch/arm/boot/dts/Makefile | 1 + >>> arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++ >>> 2 files changed, 145 insertions(+) >>> create mode 100644 arch/arm/boot/dts/pm9g45.dts >>> >>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >>> index a9b051a..627b6ad 100644 >>> --- a/arch/arm/boot/dts/Makefile >>> +++ b/arch/arm/boot/dts/Makefile >>> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb >>> dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb >>> # sam9g45 >>> dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb >>> +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb >>> # sam9n12 >>> dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb >>> # sam9x5 >>> diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts >>> new file mode 100644 >>> index 0000000..b0c258d >>> --- /dev/null >>> +++ b/arch/arm/boot/dts/pm9g45.dts >>> @@ -0,0 +1,144 @@ >>> +/* >>> + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board >>> + * >>> + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org> >>> + * >>> + * Licensed under GPLv2. >>> + */ >>> +/dts-v1/; >>> +/include/ "at91sam9g45.dtsi" >>> + >>> +/ { >>> + model = "Ronetix pm9g45"; >>> + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9"; >>> + >>> + chosen { >>> + bootargs = "console=ttyS0,115200"; >>> + }; >>> + >>> + memory { >>> + reg = <0x70000000 0x8000000>; >>> + }; >>> + >>> + clocks { >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges; >>> + >>> + main_clock: clock@0 { >>> + compatible = "atmel,osc", "fixed-clock"; >>> + clock-frequency = <12000000>; >>> + }; >>> + }; >>> + >>> + ahb { >>> + apb { >>> + dbgu: serial@ffffee00 { >>> + status = "okay"; >>> + }; >>> + >>> + pinctrl@fffff200 { >>> + >>> + board { >>> + pinctrl_board_nand: nand0-board { >>> + atmel,pins = >>> + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/ >>> + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */ >>> + }; >>> + }; >>> + }; >>> + >>> + macb0: ethernet@fffbc000 { >>> + phy-mode = "rmii"; >>> + status = "okay"; >>> + }; >>> + }; >>> + >>> + nand0: nand@40000000 { >>> + nand-bus-width = <8>; >>> + nand-ecc-mode = "soft"; >>> + nand-on-flash-bbt; >>> + pinctrl-0 = <&pinctrl_board_nand>; >>> + >>> + gpios = <&pioD 3 0 >>> + &pioC 14 0 >>> + 0 >>> + >; >>> + >>> + status = "okay"; >>> + >>> + at91bootstrap@0 { >>> + label = "at91bootstrap"; >>> + reg = <0x0 0x20000>; >>> + }; >>> + >>> + barebox@20000 { >>> + label = "barebox"; >>> + reg = <0x20000 0x40000>; >>> + }; >>> + >>> + bareboxenv@60000 { >>> + label = "bareboxenv"; >>> + reg = <0x60000 0x1A0000>; >>> + }; >>> + >>> + kernel@200000 { >>> + label = "bareboxenv2"; >>> + reg = <0x200000 0x300000>; >>> + }; >>> + >>> + kernel@500000 { >>> + label = "root"; >>> + reg = <0x500000 0x400000>; >>> + }; >>> + >>> + data@900000 { >>> + label = "data"; >>> + reg = <0x900000 0x8340000>; >>> + }; >>> + }; >>> + >>> + usb0: ohci@00700000 { >>> + status = "okay"; >>> + num-ports = <2>; >>> + }; >>> + >>> + usb1: ehci@00800000 { >>> + status = "okay"; >>> + }; >>> + }; >>> + >>> + leds { >>> + compatible = "gpio-leds"; >>> + >>> + led0 { >>> + label = "led0"; >>> + gpios = <&pioD 0 1>; >>> + linux,default-trigger = "nand-disk"; >>> + }; >>> + >>> + led1 { >>> + label = "led1"; >>> + gpios = <&pioD 31 0>; >>> + linux,default-trigger = "heartbeat"; >>> + }; >>> + }; >>> + >>> + gpio_keys { >>> + compatible = "gpio-keys"; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + right { >>> + label = "SW4"; >>> + gpios = <&pioE 7 1>; >>> + linux,code = <106>; >>> + }; >>> + >>> + up { >>> + label = "SW3"; >>> + gpios = <&pioE 8 1>; >>> + linux,code = <103>; >>> + }; >>> + }; >>> +}; >>> >> >> >> -- >> Nicolas Ferre > > -- Nicolas Ferre ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2012-11-16 13:32 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-10-19 2:19 [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <1350613168-22689-1-git-send-email-plagnioj-sclMFOaUSTBWk0Htik3J/w@public.gmane.org>
2012-11-16 13:08 ` Nicolas Ferre
[not found] ` <50A63AEA.2000706-AIFe0yeh4nAAvxtiuMwx3w@public.gmane.org>
2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD
[not found] ` <20121116132819.GG4398-RQcB7r2h9QmfDR2tN2SG5Ni2O/JbrIOy@public.gmane.org>
2012-11-16 13:32 ` Nicolas Ferre
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox