* [PATCH V2] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash
@ 2024-02-19 7:59 Sinthu Raja
2024-02-19 8:10 ` Vignesh Raghavendra
0 siblings, 1 reply; 2+ messages in thread
From: Sinthu Raja @ 2024-02-19 7:59 UTC (permalink / raw)
To: Nishanth Menon, Tero Kristo, Vignesh Raghavendra
Cc: linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja
From: Sinthu Raja <sinthu.raja@ti.com>
AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
Enable support for the same. Also, describe the OSPI flash partition
information through the device tree, according to the offsets in the
bootloader.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
---
Changes in V2:
=============
1. Address review comments
a. remove pin E20, which is not connected.
V1: https://patchwork.kernel.org/project/linux-arm-kernel/patch/20240206092334.30307-1-sinthu.raja@ti.com/
arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 78 ++++++++++++++++++++++
1 file changed, 78 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
index 0f4a5da0ebc4..afaf702cfc9d 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
@@ -130,6 +130,24 @@ rtos_ipc_memory_region: ipc-memories@a8000000 {
};
};
+&wkup_pmx0 {
+ mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+ pinctrl-single,pins = <
+ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
+ J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
+ J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
+ J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
+ J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
+ J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
+ J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
+ J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
+ J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
+ J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
+ J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
+ >;
+ };
+};
+
&wkup_pmx2 {
wkup_i2c0_pins_default: wkup-i2c0-default-pins {
pinctrl-single,pins = <
@@ -152,6 +170,66 @@ eeprom@51 {
};
};
+&ospi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x0 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ };
+ };
+ };
+};
+
&mailbox0_cluster0 {
status = "okay";
interrupts = <436>;
--
2.36.1
^ permalink raw reply related [flat|nested] 2+ messages in thread* Re: [PATCH V2] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash
2024-02-19 7:59 [PATCH V2] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash Sinthu Raja
@ 2024-02-19 8:10 ` Vignesh Raghavendra
0 siblings, 0 replies; 2+ messages in thread
From: Vignesh Raghavendra @ 2024-02-19 8:10 UTC (permalink / raw)
To: Sinthu Raja, Nishanth Menon, Tero Kristo
Cc: linux-arm-kernel, devicetree, linux-kernel, Sinthu Raja
On 19/02/24 13:29, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> AM68 SK has an OSPI NOR flash on its SOM connected to OSPI0 instance.
> Enable support for the same. Also, describe the OSPI flash partition
> information through the device tree, according to the offsets in the
> bootloader.
>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
>
> Changes in V2:
> =============
> 1. Address review comments
> a. remove pin E20, which is not connected.
>
> V1: https://patchwork.kernel.org/project/linux-arm-kernel/patch/20240206092334.30307-1-sinthu.raja@ti.com/
>
> arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi | 78 ++++++++++++++++++++++
> 1 file changed, 78 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> index 0f4a5da0ebc4..afaf702cfc9d 100644
> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-som.dtsi
> @@ -130,6 +130,24 @@ rtos_ipc_memory_region: ipc-memories@a8000000 {
> };
> };
>
> +&wkup_pmx0 {
> + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
pinmux nodes should end with -pins ^^^^^^
Please run make dtbs_check and fix the issues pointed out
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */
> + J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */
> + J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */
> + J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */
> + J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */
> + J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */
> + J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */
> + J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */
> + J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */
> + J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */
> + J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */
> + >;
> + };
> +};
> +
> &wkup_pmx2 {
> wkup_i2c0_pins_default: wkup-i2c0-default-pins {
> pinctrl-single,pins = <
> @@ -152,6 +170,66 @@ eeprom@51 {
> };
> };
>
> +&ospi0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <8>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <25000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <4>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "ospi.tiboot3";
> + reg = <0x0 0x80000>;
Should this be 1MB similar to comment at [0]
[0] lore.kernel.org/r/0ca01a1b-8956-40dd-8286-77276e021633@ti.com
> + };
> +
> + partition@80000 {
> + label = "ospi.tispl";
> + reg = <0x80000 0x200000>;
> + };
> +
> + partition@280000 {
> + label = "ospi.u-boot";
> + reg = <0x280000 0x400000>;
> + };
> +
> + partition@680000 {
> + label = "ospi.env";
> + reg = <0x680000 0x40000>;
> + };
> +
> + partition@6c0000 {
> + label = "ospi.env.backup";
> + reg = <0x6c0000 0x40000>;
> + };
> +
> + partition@800000 {
> + label = "ospi.rootfs";
> + reg = <0x800000 0x37c0000>;
> + };
> +
> + partition@3fc0000 {
> + label = "ospi.phypattern";
> + reg = <0x3fc0000 0x40000>;
> + };
> + };
> + };
> +};
> +
> &mailbox0_cluster0 {
> status = "okay";
> interrupts = <436>;
--
Regards
Vignesh
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2024-02-19 8:10 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-02-19 7:59 [PATCH V2] arm64: dts: ti: k3-am68-sk-som: Add support for OSPI flash Sinthu Raja
2024-02-19 8:10 ` Vignesh Raghavendra
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox