[PATCH v9 1/2] dt-bindings: ufs: Document static TX Equalization settings properties

[PATCH v9 1/2] dt-bindings: ufs: Document static TX Equalization settings properties

[Can Guo]

UFS v5.0/UFSHCI v5.0 adds HS-G6 support (46.6 Gbps/lane) via UniPro
v3.0 and M-PHY v6.0. These specs define TX Equalization for all
High-Speed Gears (not only HS-G6) to compensate channel loss and
improve signal integrity at high speed.

For HS-G6, M-PHY uses PAM4 1b1b line coding. Pre-Coding may also be
required depending on channel characteristics.

Document vendor-neutral properties in ufs-common.yaml:
- txeq-preshoot-g[1-6]
- txeq-deemphasis-g[1-6]
- tx-precode-enable-g6

Values are per-lane Host/Device tuples (2 values for x1, 4 values for
x2). PreShoot/DeEmphasis range from 0..7, and Precode is 0/1.

These are board-specific signal-integrity tuning values. They depend on
channel SI/PHY characterization and validation (host PHY, device PHY,
package, and board routing), and are determined by HW/PHY designers.

Although UFSHCI v5.0 supports TX Equalization Training via UniPro v3.0,
which allows host software to determine optimal TX Equalization at
runtime, static board-specific TX Equalization settings in the Device
Tree are still necessary because:
- TX Equalization Training is not supported for HS-G3 and below
- TX Equalization Training is disabled on some platforms

Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
---
 .../devicetree/bindings/ufs/ufs-common.yaml   | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/Documentation/devicetree/bindings/ufs/ufs-common.yaml b/Documentation/devicetree/bindings/ufs/ufs-common.yaml
index ed97f5682509..cc32e1189d50 100644
--- a/Documentation/devicetree/bindings/ufs/ufs-common.yaml
+++ b/Documentation/devicetree/bindings/ufs/ufs-common.yaml
@@ -105,6 +105,64 @@ properties:
       Restricts the UFS controller to rate-a or rate-b for both TX and
       RX directions.
 
+  tx-precode-enable-g6:
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    minItems: 1
+    items:
+      - items:
+          - description: Host_Lane0 precode
+            enum: [0, 1]
+          - description: Device_Lane0 precode
+            enum: [0, 1]
+      - items:
+          - description: Host_Lane1 precode
+            enum: [0, 1]
+          - description: Device_Lane1 precode
+            enum: [0, 1]
+    description:
+      Static TX Precode enable values for HS-G6 only.
+
+patternProperties:
+  "^txeq-preshoot-g[1-6]$":
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    minItems: 1
+    items:
+      - items:
+          - description: Host_Lane0 Preshoot value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          - description: Device_Lane0 Preshoot value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+      - items:
+          - description: Host_Lane1 Preshoot value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          - description: Device_Lane1 Preshoot value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+    description: |
+      Static TX Equalization PreShoot settings for High Speed Gears. These
+      values are programmed to the corresponding UniPro PA layer attribute
+      PA_TxEQG[1-6]Setting. Each value selects a Pre-Shoot level as defined
+      by the MIPI M-PHY specification (TX_HS_PreShoot_Setting).
+
+  "^txeq-deemphasis-g[1-6]$":
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    minItems: 1
+    items:
+      - items:
+          - description: Host_Lane0 DeEmphasis value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          - description: Device_Lane0 DeEmphasis value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+      - items:
+          - description: Host_Lane1 DeEmphasis value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+          - description: Device_Lane1 DeEmphasis value
+            enum: [0, 1, 2, 3, 4, 5, 6, 7]
+    description: |
+      Static TX Equalization DeEmphasis settings for High Speed Gears. These
+      values are programmed to the corresponding UniPro PA layer attribute
+      PA_TxEQG[1-6]Setting. Each value selects a De-Emphasis level as defined
+      by the MIPI M-PHY specification (TX_HS_DeEmphasis_Setting).
+
 dependencies:
   freq-table-hz: [ clocks ]
   operating-points-v2: [ clocks, clock-names ]
-- 
2.34.1

Re: [PATCH v9 1/2] dt-bindings: ufs: Document static TX Equalization settings properties

[Krzysztof Kozlowski]

On 15/06/2026 15:28, Can Guo wrote:
> UFS v5.0/UFSHCI v5.0 adds HS-G6 support (46.6 Gbps/lane) via UniPro
> v3.0 and M-PHY v6.0. These specs define TX Equalization for all
> High-Speed Gears (not only HS-G6) to compensate channel loss and
> improve signal integrity at high speed.
> 
> For HS-G6, M-PHY uses PAM4 1b1b line coding. Pre-Coding may also be
> required depending on channel characteristics.
> 
> Document vendor-neutral properties in ufs-common.yaml:
> - txeq-preshoot-g[1-6]
> - txeq-deemphasis-g[1-6]
> - tx-precode-enable-g6
> 
> Values are per-lane Host/Device tuples (2 values for x1, 4 values for
> x2). PreShoot/DeEmphasis range from 0..7, and Precode is 0/1.
> 
> These are board-specific signal-integrity tuning values. They depend on
> channel SI/PHY characterization and validation (host PHY, device PHY,
> package, and board routing), and are determined by HW/PHY designers.
> 
> Although UFSHCI v5.0 supports TX Equalization Training via UniPro v3.0,
> which allows host software to determine optimal TX Equalization at
> runtime, static board-specific TX Equalization settings in the Device
> Tree are still necessary because:
> - TX Equalization Training is not supported for HS-G3 and below
> - TX Equalization Training is disabled on some platforms
> 
> Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
> ---
>  .../devicetree/bindings/ufs/ufs-common.yaml   | 58 +++++++++++++++++++
>  1 file changed, 58 insertions(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v9 1/2] dt-bindings: ufs: Document static TX Equalization settings properties

[Peter Wang (王信友)]

On Mon, 2026-06-15 at 06:28 -0700, Can Guo wrote:
> UFS v5.0/UFSHCI v5.0 adds HS-G6 support (46.6 Gbps/lane) via UniPro
> v3.0 and M-PHY v6.0. These specs define TX Equalization for all
> High-Speed Gears (not only HS-G6) to compensate channel loss and
> improve signal integrity at high speed.
> 
> For HS-G6, M-PHY uses PAM4 1b1b line coding. Pre-Coding may also be
> required depending on channel characteristics.
> 
> Document vendor-neutral properties in ufs-common.yaml:
> - txeq-preshoot-g[1-6]
> - txeq-deemphasis-g[1-6]
> - tx-precode-enable-g6
> 
> Values are per-lane Host/Device tuples (2 values for x1, 4 values for
> x2). PreShoot/DeEmphasis range from 0..7, and Precode is 0/1.
> 
> These are board-specific signal-integrity tuning values. They depend
> on
> channel SI/PHY characterization and validation (host PHY, device PHY,
> package, and board routing), and are determined by HW/PHY designers.
> 
> Although UFSHCI v5.0 supports TX Equalization Training via UniPro
> v3.0,
> which allows host software to determine optimal TX Equalization at
> runtime, static board-specific TX Equalization settings in the Device
> Tree are still necessary because:
> - TX Equalization Training is not supported for HS-G3 and below
> - TX Equalization Training is disabled on some platforms
> 
> Signed-off-by: Can Guo <can.guo@oss.qualcomm.com>
> ---

Reviewed-by: Peter Wang <peter.wang@mediatek.com>