* [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format.
@ 2025-10-14 18:55 Frank Li
2025-10-15 21:13 ` David Heidelberg
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Frank Li @ 2025-10-14 18:55 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Hans Verkuil, Laurent Pinchart, David Heidelberg,
Sakari Ailus, open list:MEDIA INPUT INFRASTRUCTURE (V4L/DVB),
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
Cc: imx
Convert ti,tvp5150.txt to yaml format.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
.../bindings/media/i2c/ti,tvp5150.txt | 157 ------------------
.../bindings/media/i2c/ti,tvp5150.yaml | 133 +++++++++++++++
2 files changed, 133 insertions(+), 157 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
deleted file mode 100644
index 94b908ace53c8..0000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
+++ /dev/null
@@ -1,157 +0,0 @@
-* Texas Instruments TVP5150 and TVP5151 video decoders
-
-The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
-(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
-with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
-
-Required Properties:
-====================
-- compatible: Value must be "ti,tvp5150".
-- reg: I2C slave address.
-
-Optional Properties:
-====================
-- pdn-gpios: Phandle for the GPIO connected to the PDN pin, if any.
-- reset-gpios: Phandle for the GPIO connected to the RESETB pin, if any.
-
-The device node must contain one 'port' child node per device physical input
-and output port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
-are numbered as follows
-
- Name Type Port
- --------------------------------------
- AIP1A sink 0
- AIP1B sink 1
- Y-OUT src 2
-
-The device node must contain at least one sink port and the src port. Each input
-port must be linked to an endpoint defined in [1]. The port/connector layout is
-as follows
-
-tvp-5150 port@0 (AIP1A)
- endpoint@0 -----------> Comp0-Con port
- endpoint@1 ------+----> Svideo-Con port
-tvp-5150 port@1 (AIP1B) |
- endpoint@1 ------+
- endpoint@0 -----------> Comp1-Con port
-tvp-5150 port@2
- endpoint (video bitstream output at YOUT[0-7] parallel bus)
-
-Required Endpoint Properties for parallel synchronization on output port:
-=========================================================================
-
-- hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
-- vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
-- field-even-active: Field signal level during the even field data
- transmission. Must be <0>.
-
-Note: Do not specify any of these properties if you want to use the embedded
- BT.656 synchronization.
-
-Optional Connector Properties:
-==============================
-
-- sdtv-standards: Set the possible signals to which the hardware tries to lock
- instead of using the autodetection mechanism. Please look at
- [1] for more information.
-
-[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml.
-
-Example - three input sources:
-#include <dt-bindings/display/sdtv-standards.h>
-
-comp_connector_0 {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */
-
- port {
- composite0_to_tvp5150: endpoint {
- remote-endpoint = <&tvp5150_to_composite0>;
- };
- };
-};
-
-comp_connector_1 {
- compatible = "composite-video-connector";
- label = "Composite1";
- sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */
-
- port {
- composite1_to_tvp5150: endpoint {
- remote-endpoint = <&tvp5150_to_composite1>;
- };
- };
-};
-
-svideo_connector {
- compatible = "svideo-connector";
- label = "S-Video";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- svideo_luma_to_tvp5150: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tvp5150_to_svideo_luma>;
- };
-
- svideo_chroma_to_tvp5150: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&tvp5150_to_svideo_chroma>;
- };
- };
-};
-
-&i2c2 {
- tvp5150@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
- reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tvp5150_to_composite0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&composite0_to_tvp5150>;
- };
-
- tvp5150_to_svideo_luma: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&svideo_luma_to_tvp5150>;
- };
- };
-
- port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tvp5150_to_composite1: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&composite1_to_tvp5150>;
- };
-
- tvp5150_to_svideo_chroma: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&svideo_chroma_to_tvp5150>;
- };
- };
-
- port@2 {
- reg = <2>;
-
- tvp5150_1: endpoint {
- remote-endpoint = <&ccdc_ep>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
new file mode 100644
index 0000000000000..4869ba7ca0763
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ti,tvp5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments TVP5150 and TVP5151 video decoders
+
+maintainers:
+ - Frank Li <Frank.Li@nxp.com>
+
+description:
+ The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+ (and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+ with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+properties:
+ compatible:
+ const: ti,tvp5150
+
+ reg:
+ maxItems: 1
+
+ pdn-gpios:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ port@0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ sink port node, AIP1A
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ port@1:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ sink port node, AIP1B
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ port@2:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ source port node, Y-OUT
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - port@2
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/display/sdtv-standards.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge@5c {
+ compatible = "ti,tvp5150";
+ reg = <0x5c>;
+ pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&composite0_to_tvp5150>;
+ };
+
+ endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&svideo_luma_to_tvp5150>;
+ };
+ };
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&composite1_to_tvp5150>;
+ };
+
+ endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&svideo_chroma_to_tvp5150>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ endpoint {
+ remote-endpoint = <&ccdc_ep>;
+ };
+ };
+ };
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format.
2025-10-14 18:55 [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format Frank Li
@ 2025-10-15 21:13 ` David Heidelberg
2025-10-20 21:04 ` Rob Herring (Arm)
2025-10-21 8:33 ` Sakari Ailus
2 siblings, 0 replies; 4+ messages in thread
From: David Heidelberg @ 2025-10-15 21:13 UTC (permalink / raw)
To: Frank Li, Mauro Carvalho Chehab, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Hans Verkuil, Laurent Pinchart, Sakari Ailus,
open list:MEDIA INPUT INFRASTRUCTURE (V4L/DVB),
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list
Cc: imx
LGTM
Reviewed-by: David Heidelberg <david@ixit.cz>
On 14/10/2025 20:55, Frank Li wrote:
> Convert ti,tvp5150.txt to yaml format.
>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> .../bindings/media/i2c/ti,tvp5150.txt | 157 ------------------
> .../bindings/media/i2c/ti,tvp5150.yaml | 133 +++++++++++++++
> 2 files changed, 133 insertions(+), 157 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
> deleted file mode 100644
> index 94b908ace53c8..0000000000000
> --- a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
> +++ /dev/null
> @@ -1,157 +0,0 @@
> -* Texas Instruments TVP5150 and TVP5151 video decoders
> -
> -The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
> -(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
> -with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
> -
> -Required Properties:
> -====================
> -- compatible: Value must be "ti,tvp5150".
> -- reg: I2C slave address.
> -
> -Optional Properties:
> -====================
> -- pdn-gpios: Phandle for the GPIO connected to the PDN pin, if any.
> -- reset-gpios: Phandle for the GPIO connected to the RESETB pin, if any.
> -
> -The device node must contain one 'port' child node per device physical input
> -and output port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
> -are numbered as follows
> -
> - Name Type Port
> - --------------------------------------
> - AIP1A sink 0
> - AIP1B sink 1
> - Y-OUT src 2
> -
> -The device node must contain at least one sink port and the src port. Each input
> -port must be linked to an endpoint defined in [1]. The port/connector layout is
> -as follows
> -
> -tvp-5150 port@0 (AIP1A)
> - endpoint@0 -----------> Comp0-Con port
> - endpoint@1 ------+----> Svideo-Con port
> -tvp-5150 port@1 (AIP1B) |
> - endpoint@1 ------+
> - endpoint@0 -----------> Comp1-Con port
> -tvp-5150 port@2
> - endpoint (video bitstream output at YOUT[0-7] parallel bus)
> -
> -Required Endpoint Properties for parallel synchronization on output port:
> -=========================================================================
> -
> -- hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
> -- vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
> -- field-even-active: Field signal level during the even field data
> - transmission. Must be <0>.
> -
> -Note: Do not specify any of these properties if you want to use the embedded
> - BT.656 synchronization.
> -
> -Optional Connector Properties:
> -==============================
> -
> -- sdtv-standards: Set the possible signals to which the hardware tries to lock
> - instead of using the autodetection mechanism. Please look at
> - [1] for more information.
> -
> -[1] Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml.
> -
> -Example - three input sources:
> -#include <dt-bindings/display/sdtv-standards.h>
> -
> -comp_connector_0 {
> - compatible = "composite-video-connector";
> - label = "Composite0";
> - sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */
> -
> - port {
> - composite0_to_tvp5150: endpoint {
> - remote-endpoint = <&tvp5150_to_composite0>;
> - };
> - };
> -};
> -
> -comp_connector_1 {
> - compatible = "composite-video-connector";
> - label = "Composite1";
> - sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */
> -
> - port {
> - composite1_to_tvp5150: endpoint {
> - remote-endpoint = <&tvp5150_to_composite1>;
> - };
> - };
> -};
> -
> -svideo_connector {
> - compatible = "svideo-connector";
> - label = "S-Video";
> -
> - port {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - svideo_luma_to_tvp5150: endpoint@0 {
> - reg = <0>;
> - remote-endpoint = <&tvp5150_to_svideo_luma>;
> - };
> -
> - svideo_chroma_to_tvp5150: endpoint@1 {
> - reg = <1>;
> - remote-endpoint = <&tvp5150_to_svideo_chroma>;
> - };
> - };
> -};
> -
> -&i2c2 {
> - tvp5150@5c {
> - compatible = "ti,tvp5150";
> - reg = <0x5c>;
> - pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
> - reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port@0 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <0>;
> -
> - tvp5150_to_composite0: endpoint@0 {
> - reg = <0>;
> - remote-endpoint = <&composite0_to_tvp5150>;
> - };
> -
> - tvp5150_to_svideo_luma: endpoint@1 {
> - reg = <1>;
> - remote-endpoint = <&svideo_luma_to_tvp5150>;
> - };
> - };
> -
> - port@1 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - reg = <1>;
> -
> - tvp5150_to_composite1: endpoint@0 {
> - reg = <0>;
> - remote-endpoint = <&composite1_to_tvp5150>;
> - };
> -
> - tvp5150_to_svideo_chroma: endpoint@1 {
> - reg = <1>;
> - remote-endpoint = <&svideo_chroma_to_tvp5150>;
> - };
> - };
> -
> - port@2 {
> - reg = <2>;
> -
> - tvp5150_1: endpoint {
> - remote-endpoint = <&ccdc_ep>;
> - };
> - };
> - };
> -};
> diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
> new file mode 100644
> index 0000000000000..4869ba7ca0763
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
> @@ -0,0 +1,133 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ti,tvp5150.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Texas Instruments TVP5150 and TVP5151 video decoders
> +
> +maintainers:
> + - Frank Li <Frank.Li@nxp.com>
> +
> +description:
> + The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
> + (and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
> + with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
> +
> +properties:
> + compatible:
> + const: ti,tvp5150
> +
> + reg:
> + maxItems: 1
> +
> + pdn-gpios:
> + maxItems: 1
> +
> + reset-gpios:
> + maxItems: 1
> +
> + '#address-cells':
> + const: 1
> +
> + '#size-cells':
> + const: 0
> +
> + port@0:
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + unevaluatedProperties: false
> + description:
> + sink port node, AIP1A
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + port@1:
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + unevaluatedProperties: false
> + description:
> + sink port node, AIP1B
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + port@2:
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + unevaluatedProperties: false
> + description:
> + source port node, Y-OUT
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - reg
> + - port@2
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/display/sdtv-standards.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bridge@5c {
> + compatible = "ti,tvp5150";
> + reg = <0x5c>;
> + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&composite0_to_tvp5150>;
> + };
> +
> + endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&svideo_luma_to_tvp5150>;
> + };
> + };
> +
> + port@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&composite1_to_tvp5150>;
> + };
> +
> + endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&svideo_chroma_to_tvp5150>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + endpoint {
> + remote-endpoint = <&ccdc_ep>;
> + };
> + };
> + };
> + };
--
David Heidelberg
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format.
2025-10-14 18:55 [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format Frank Li
2025-10-15 21:13 ` David Heidelberg
@ 2025-10-20 21:04 ` Rob Herring (Arm)
2025-10-21 8:33 ` Sakari Ailus
2 siblings, 0 replies; 4+ messages in thread
From: Rob Herring (Arm) @ 2025-10-20 21:04 UTC (permalink / raw)
To: Frank Li
Cc: linux-media, Hans Verkuil, Mauro Carvalho Chehab,
David Heidelberg, Conor Dooley, Krzysztof Kozlowski, imx,
linux-kernel, Laurent Pinchart, devicetree, Sakari Ailus
On Tue, 14 Oct 2025 14:55:09 -0400, Frank Li wrote:
> Convert ti,tvp5150.txt to yaml format.
>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> .../bindings/media/i2c/ti,tvp5150.txt | 157 ------------------
> .../bindings/media/i2c/ti,tvp5150.yaml | 133 +++++++++++++++
> 2 files changed, 133 insertions(+), 157 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format.
2025-10-14 18:55 [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format Frank Li
2025-10-15 21:13 ` David Heidelberg
2025-10-20 21:04 ` Rob Herring (Arm)
@ 2025-10-21 8:33 ` Sakari Ailus
2 siblings, 0 replies; 4+ messages in thread
From: Sakari Ailus @ 2025-10-21 8:33 UTC (permalink / raw)
To: Frank Li
Cc: Mauro Carvalho Chehab, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Hans Verkuil, Laurent Pinchart, David Heidelberg,
open list:MEDIA INPUT INFRASTRUCTURE (V4L/DVB),
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
open list, imx
Hi Frank,
Thanks for the patch.
On Tue, Oct 14, 2025 at 02:55:09PM -0400, Frank Li wrote:
> +examples:
> + - |
> + #include <dt-bindings/display/sdtv-standards.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bridge@5c {
> + compatible = "ti,tvp5150";
> + reg = <0x5c>;
> + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&composite0_to_tvp5150>;
> + };
> +
> + endpoint@1 {
> + reg = <1>;
> + remote-endpoint = <&svideo_luma_to_tvp5150>;
I aligned these while applying the patch.
--
Sakari Ailus
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2025-10-21 8:33 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-10-14 18:55 [PATCH 1/1] dt-bindings: media: Convert ti,tvp5150.txt to yaml format Frank Li
2025-10-15 21:13 ` David Heidelberg
2025-10-20 21:04 ` Rob Herring (Arm)
2025-10-21 8:33 ` Sakari Ailus
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox