Re: [PATCH v4 3/6] PCI: spacemit-k1: Add device id update helper

[Inochi Amaoto <inochiama@gmail.com>]

On Fri, Jul 10, 2026 at 11:01:27AM -0500, Alex Elder wrote:
> On 7/8/26 11:00 PM, Inochi Amaoto wrote:
> > Both K1 and K3 needs to set vendor id and device id, add a helper function
> 
> s/needs/need/
> 
> > to simplify this.
> 
> I think someone might have commented on this, but I expected to find
> that the next patch would fill in the code that's needed to support
> K3, but that patch is at the end of your series.
> 
> The reason I say it here is that I wondered while looking at this
> one why it was needed to create this helper function.  I now know
> that k3_pcie_init() will call it (but I had to find that in the
> last patch, which was later than I expected).
> 
> Your series should start with DT binding changes, then code changes,
> and (often) end with DTS changes.
> 

There is another order, starts with the common change, then 
the specific logic for a specific driver. This is the order
of this patchset. For this patchset, starting with DT binding
changes makes the common part hard to be identified and taken.

> Anyway, this looks good.
> 
> Reviewed-by: Alex Elder <elder@riscstar.com>
> 
> > Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
> > ---
> >   drivers/pci/controller/dwc/pcie-spacemit-k1.c | 17 +++++++++++++----
> >   1 file changed, 13 insertions(+), 4 deletions(-)
> > 
> > diff --git a/drivers/pci/controller/dwc/pcie-spacemit-k1.c b/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > index e22ecbd09579..31aac056b68e 100644
> > --- a/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > +++ b/drivers/pci/controller/dwc/pcie-spacemit-k1.c
> > @@ -56,6 +56,7 @@ struct k1_pcie_device_data {
> >   	const struct dw_pcie_ops *ops;
> >   	int (*parse_port)(struct k1_pcie *k1);
> >   	unsigned int max_phy_count;
> > +	unsigned int device_id;
> >   };
> >   struct k1_pcie {
> > @@ -186,6 +187,16 @@ static void k1_pcie_disable_aspm_l1(struct k1_pcie *k1)
> >   	dw_pcie_dbi_ro_wr_dis(pci);
> >   }
> > +static void k1_pcie_set_device_id(struct k1_pcie *k1)
> > +{
> > +	struct dw_pcie *pci = &k1->pci;
> > +
> > +	dw_pcie_dbi_ro_wr_en(pci);
> > +	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_SPACEMIT);
> > +	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, k1->data->device_id);
> > +	dw_pcie_dbi_ro_wr_dis(pci);
> > +}
> > +
> >   static int k1_pcie_init(struct dw_pcie_rp *pp)
> >   {
> >   	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > @@ -201,10 +212,7 @@ static int k1_pcie_init(struct dw_pcie_rp *pp)
> >   		return ret;
> >   	/* Set the PCI vendor and device ID */
> > -	dw_pcie_dbi_ro_wr_en(pci);
> > -	dw_pcie_writew_dbi(pci, PCI_VENDOR_ID, PCI_VENDOR_ID_SPACEMIT);
> > -	dw_pcie_writew_dbi(pci, PCI_DEVICE_ID, PCI_DEVICE_ID_SPACEMIT_K1);
> > -	dw_pcie_dbi_ro_wr_dis(pci);
> > +	k1_pcie_set_device_id(k1);
> >   	/*
> >   	 * Start by asserting fundamental reset (drive PERST# low).  The
> > @@ -406,6 +414,7 @@ static const struct k1_pcie_device_data k1_pcie_device_data = {
> >   	.ops		= &k1_pcie_ops,
> >   	.parse_port	= k1_pcie_parse_port,
> >   	.max_phy_count	= 1,
> > +	.device_id	= PCI_DEVICE_ID_SPACEMIT_K1,
> >   };
> >   static const struct of_device_id k1_pcie_of_match_table[] = {
>