[PATCH 0/4] iio: pressure: dps310: fix pressure overflow, add Zilltek ZTS8032

[PATCH 0/4] iio: pressure: dps310: fix pressure overflow, add Zilltek ZTS8032

[Paulius Zaleckas]

From: Paulius Zaleckas <paulius.zaleckas@gmail.com>

The Zilltek ZTS8032 is a register compatible DPS310 with two more
pressure calibration coefficients. Bringing it up showed that the DPS310
pressure compensation overflows s64 at most oversampling rates, so patch
1 fixes that first (Fixes: + stable); the rest adds the ZTS8032.

1: Evaluate the compensation polynomial in Q20 fixed point. The current
   p^3 * c30 / kP^3 sum overflows, losing the c30 term: about 20 Pa low
   near sea level at oversampling 2, 4, 8, 64 and 128.
2-3: Vendor prefix and the zilltek,zts8032 compatible.
4: Per-chip data for the coefficient count (c31, c40) and the TMP_CFG
   startup value, since TMP_CFG bit 7 is a rate bit on the ZTS8032.

Based on iio/togreg, on top of 4334dc4092c2 ("iio: pressure: dps310: fix
CFG_REG bit definitions"), without which oversampling 16 and above
returns -ERANGE.

Testing: ZTS8032 on an arm64 (MT7987) board, both fixes backported to
6.12. in_pressure_input matches the datasheet formula evaluated from the
raw and coefficient registers to within 1 Pa at every oversampling rate
from 1 to 128; the fixed point math was also checked against a floating
point model over 300-1200 hPa for all rates. Builds without warnings
with W=1 on x86_64 and i386, dt_binding_check passes. I have no DPS310,
so patch 1 is untested on one.

checkpatch --strict suggests BIT_ULL() for DPS310_Q_ONE; it stays a
signed 1LL << 20 because it multiplies signed raw values.

An LLM coding assistant (Claude Code) was used for this series: it
found the overflow while porting the ZTS8032 vendor driver, wrote the
code and changelogs, the floating point model and the hardware test
scripts, under my direction. I reviewed and tested the result.

Paulius Zaleckas (4):
  iio: pressure: dps310: fix overflow in the pressure compensation
  dt-bindings: vendor-prefixes: Add ZillTek Technology
  dt-bindings: iio: pressure: infineon,dps310: Add Zilltek ZTS8032
  iio: pressure: dps310: add Zilltek ZTS8032 support

 .../iio/pressure/infineon,dps310.yaml         |   4 +-
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 drivers/iio/pressure/Kconfig                  |   4 +-
 drivers/iio/pressure/dps310.c                 | 149 +++++++++++-------
 4 files changed, 99 insertions(+), 60 deletions(-)


base-commit: a3b3580713f3ac5a32dc2874ee546828977a1d68
-- 
2.55.0

[PATCH 1/4] iio: pressure: dps310: fix overflow in the pressure compensation

[Paulius Zaleckas]

From: Paulius Zaleckas <paulius.zaleckas@gmail.com>

dps310_calculate_pressure() sums the compensation polynomial as
p^n * c / kP^n fractions in s64. The raw pressure scales with kP, which
goes up to 7864320, so p^3 * c30 overflows at most oversampling rates
near sea level, kP^3 wraps negative at 4x and 8x, and the remainders
overflow when scaled by 10^9. The c30 term is then lost: at about
1006 hPa the pressure reads about 20 Pa low at oversampling 2, 4, 8, 64
and 128, and hundreds of Pa off towards the ends of the 300-1200 hPa
range.

Evaluate the polynomial in Q20 fixed point instead. The linear c10 and
c01 terms are still divided exactly, the higher order terms use the
scaled raw values. Over 300-1200 hPa and every oversampling rate the
result is within 1 Pa of the floating point formula.

Tested on a register compatible Zilltek ZTS8032 (support added later in
this series) at about 1007 hPa, against the datasheet formula evaluated
from the raw and coefficient registers. A vendor driver with the same
algebra read 13-20 Pa low at oversampling 2, 4, 8, 64 and 128; with this
series every rate is within 1 Pa. Not tested on a DPS310.

Fixes: d711a3c7dc82 ("iio: dps310: Add pressure sensing capability")
Cc: stable@vger.kernel.org
Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 drivers/iio/pressure/dps310.c | 83 ++++++++++++++---------------------
 1 file changed, 34 insertions(+), 49 deletions(-)

diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
index 85df58ac1809..3bc690cc8609 100644
--- a/drivers/iio/pressure/dps310.c
+++ b/drivers/iio/pressure/dps310.c
@@ -660,71 +660,56 @@ static int dps310_write_raw(struct iio_dev *iio,
 	}
 }
 
+/* Fraction bits of the fixed point pressure compensation */
+#define DPS310_Q	20
+#define DPS310_Q_ONE	(1LL << DPS310_Q)
+
+static s64 dps310_mul_q(s64 a, s64 b)
+{
+	return (a * b) >> DPS310_Q;
+}
+
 static int dps310_calculate_pressure(struct dps310_data *data, int *val)
 	__must_hold(&data->lock)
 {
-	int i;
 	int rc;
-	int kpi;
-	int kti;
-	s64 rem = 0ULL;
-	s64 pressure = 0ULL;
+	int kp;
+	int kt;
+	s64 pressure;
 	s64 p;
 	s64 t;
-	s64 denoms[7];
-	s64 nums[7];
-	s64 rems[7];
-	s64 kp;
-	s64 kt;
+	s64 ps;
+	s64 ts;
+	s64 x2;
+	s64 x3;
 
-	rc = dps310_get_pres_k(data, &kpi);
+	rc = dps310_get_pres_k(data, &kp);
 	if (rc)
 		return rc;
 
-	rc = dps310_get_temp_k(data, &kti);
+	rc = dps310_get_temp_k(data, &kt);
 	if (rc)
 		return rc;
 
-	kp = (s64)kpi;
-	kt = (s64)kti;
-
 	p = (s64)data->pressure_raw;
 	t = (s64)data->temp_raw;
 
-	/* Section 4.9.1 of the DPS310 spec; algebra'd to avoid underflow */
-	nums[0] = (s64)data->c00;
-	denoms[0] = 1LL;
-	nums[1] = p * (s64)data->c10;
-	denoms[1] = kp;
-	nums[2] = p * p * (s64)data->c20;
-	denoms[2] = kp * kp;
-	nums[3] = p * p * p * (s64)data->c30;
-	denoms[3] = kp * kp * kp;
-	nums[4] = t * (s64)data->c01;
-	denoms[4] = kt;
-	nums[5] = t * p * (s64)data->c11;
-	denoms[5] = kp * kt;
-	nums[6] = t * p * p * (s64)data->c21;
-	denoms[6] = kp * kp * kt;
-
-	/* Kernel lacks a div64_s64_rem function; denoms are all positive */
-	for (i = 0; i < 7; ++i) {
-		u64 irem;
-
-		if (nums[i] < 0LL) {
-			pressure -= div64_u64_rem(-nums[i], denoms[i], &irem);
-			rems[i] = -irem;
-		} else {
-			pressure += div64_u64_rem(nums[i], denoms[i], &irem);
-			rems[i] = (s64)irem;
-		}
-	}
-
-	/* Increase precision and calculate the remainder sum */
-	for (i = 0; i < 7; ++i)
-		rem += div64_s64((s64)rems[i] * 1000000000LL, denoms[i]);
-
-	pressure += div_s64(rem, 1000000000LL);
+	/*
+	 * Section 4.9.1 of the DPS310 spec in fixed point. Dividing p^3 * c30
+	 * by kP^3 directly overflows s64 at most oversampling rates.
+	 */
+	ps = div_s64(p * DPS310_Q_ONE, kp);
+	ts = div_s64(t * DPS310_Q_ONE, kt);
+	x2 = dps310_mul_q(ps, ps);
+	x3 = dps310_mul_q(x2, ps);
+
+	pressure = data->c00 * DPS310_Q_ONE;
+	pressure += div_s64(p * data->c10 * DPS310_Q_ONE, kp);
+	pressure += div_s64(t * data->c01 * DPS310_Q_ONE, kt);
+	pressure += dps310_mul_q(data->c11 * ps, ts);
+	pressure += data->c20 * x2 + data->c30 * x3;
+	pressure += dps310_mul_q(data->c21 * x2, ts);
+	pressure >>= DPS310_Q;
 	if (pressure < 0LL)
 		return -ERANGE;
 
-- 
2.55.0

[PATCH 2/4] dt-bindings: vendor-prefixes: Add ZillTek Technology

[Paulius Zaleckas]

From: Paulius Zaleckas <paulius.zaleckas@gmail.com>

ZillTek Technology Corp. (Hsinchu, Taiwan) makes MEMS microphones and
barometric pressure sensors such as the ZTS8032.

Link: https://www.zilltek.com/
Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ba2002969373..255dc56edc36 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1977,6 +1977,8 @@ patternProperties:
     description: Shenzhen Zidoo Technology Co., Ltd.
   "^zii,.*":
     description: Zodiac Inflight Innovations
+  "^zilltek,.*":
+    description: ZillTek Technology Corp.
   "^zinitix,.*":
     description: Zinitix Co., Ltd
   "^zkmagic,.*":
-- 
2.55.0

[PATCH 3/4] dt-bindings: iio: pressure: infineon,dps310: Add Zilltek ZTS8032

[Paulius Zaleckas]

From: Paulius Zaleckas <paulius.zaleckas@gmail.com>

The Zilltek ZTS8032 is register compatible with the DPS310, but has two
more pressure calibration coefficients and takes its temperature from a
different sensor by default, so it cannot use the DPS310 compatible as a
fallback.

Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 .../devicetree/bindings/iio/pressure/infineon,dps310.yaml     | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
index 1912a1b0b4ba..416117dfd927 100644
--- a/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
+++ b/Documentation/devicetree/bindings/iio/pressure/infineon,dps310.yaml
@@ -11,12 +11,14 @@ maintainers:
 
 description:
   The DPS310 is a barometric pressure and temperature sensor with an I2C
-  interface.
+  interface. The Zilltek ZTS8032 is register compatible with it, but has
+  additional calibration coefficients.
 
 properties:
   compatible:
     enum:
       - infineon,dps310
+      - zilltek,zts8032
 
   reg:
     maxItems: 1
-- 
2.55.0

[PATCH 4/4] iio: pressure: dps310: add Zilltek ZTS8032 support

[Paulius Zaleckas]

From: Paulius Zaleckas <paulius.zaleckas@gmail.com>

The Zilltek ZTS8032 has the DPS310 register map, scale factors and
compensation, with these differences:

- two more pressure coefficients, c31 and c40 at 0x22-0x25, adding
  c40 * Praw_sc^4 + c31 * Traw_sc * Praw_sc^3 to the polynomial
- TMP_EXT is MEAS_CFG bit 3, and the temperature coefficients are for
  the internal sensor (COEF_SRCE reads 0x06). TMP_CFG bit 7 is the top
  bit of a 4-bit TMP_RATE, so the DPS310 TMP_EXT write would select a
  25/16 Hz background rate instead of the external sensor.
- product ID 0x11 instead of 0x10, the driver does not check it

Add a per-chip table holding the coefficient count and the TMP_CFG
startup value, and an OF match table to select it.

Tested on a ZTS8032 at 0x76 over I2C: in_pressure_input is within 1 Pa
of the datasheet formula evaluated from the raw and coefficient
registers at every oversampling rate from 1 to 128, and TMP_CFG reads
0x00 after probe.

Assisted-by: LLM
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
---
 drivers/iio/pressure/Kconfig  |  4 +--
 drivers/iio/pressure/dps310.c | 66 ++++++++++++++++++++++++++++++-----
 2 files changed, 60 insertions(+), 10 deletions(-)

diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
index cef8b90b9ae7..e407243e131c 100644
--- a/drivers/iio/pressure/Kconfig
+++ b/drivers/iio/pressure/Kconfig
@@ -115,8 +115,8 @@ config DPS310
 	select IIO_BUFFER
 	select IIO_TRIGGERED_BUFFER
 	help
-	  Support for the Infineon DPS310 digital barometric pressure sensor.
-	  It can be accessed over I2C bus.
+	  Support for the Infineon DPS310 and Zilltek ZTS8032 digital
+	  barometric pressure sensors. They can be accessed over I2C bus.
 
 	  This driver can also be built as a module.  If so, the module will be
 	  called dps310.
diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
index 3bc690cc8609..3b0f6d344409 100644
--- a/drivers/iio/pressure/dps310.c
+++ b/drivers/iio/pressure/dps310.c
@@ -7,6 +7,10 @@
  *
  * https://www.infineon.com/dgdl/?fileId=5546d462576f34750157750826c42242
  *
+ * The Zilltek ZTS8032 is register compatible, with two more pressure
+ * calibration coefficients (c31, c40) and temperature calibrated against
+ * the internal sensor.
+ *
  * Temperature calculation:
  *   c0 * 0.5 + c1 * T_raw / kT °C
  *
@@ -18,6 +22,7 @@
 #include <linux/i2c.h>
 #include <linux/limits.h>
 #include <linux/math64.h>
+#include <linux/mod_devicetable.h>
 #include <linux/module.h>
 #include <linux/regmap.h>
 #include <linux/unaligned.h>
@@ -61,6 +66,8 @@
 #define DPS310_RESET		0x0c
 #define  DPS310_RESET_MAGIC	0x09
 #define DPS310_COEF_BASE	0x10
+#define DPS310_COEF_LEN		18
+#define ZTS8032_COEF_LEN	22
 
 /* Make sure sleep time is <= 30ms for usleep_range */
 #define DPS310_POLL_SLEEP_US(t)		min(30000, (t) / 8)
@@ -85,13 +92,34 @@ static const int scale_factors[] = {
 	2088960,
 };
 
+struct dps310_chip_info {
+	const char *name;
+	u8 tmp_cfg;	/* TMP_CFG at startup: sensor the coefficients are for */
+	u8 coef_len;
+};
+
+static const struct dps310_chip_info dps310_chip_info = {
+	.name = "dps310",
+	.tmp_cfg = DPS310_TMP_EXT,
+	.coef_len = DPS310_COEF_LEN,
+};
+
+/* TMP_CFG bit 7 is a rate bit here; the internal sensor is the default */
+static const struct dps310_chip_info zts8032_chip_info = {
+	.name = "zts8032",
+	.tmp_cfg = 0,
+	.coef_len = ZTS8032_COEF_LEN,
+};
+
 struct dps310_data {
 	struct i2c_client *client;
 	struct regmap *regmap;
 	struct mutex lock;	/* Lock for sequential HW access functions */
+	const struct dps310_chip_info *info;
 
 	s32 c0, c1;
 	s32 c00, c10, c20, c30, c01, c11, c21;
+	s32 c31, c40;
 	s32 pressure_raw;
 	s32 temp_raw;
 	bool timeout_recovery_failed;
@@ -148,13 +176,13 @@ static const struct iio_chan_spec dps310_channels[] = {
 static int dps310_get_coefs(struct dps310_data *data)
 {
 	int rc;
-	u8 coef[18];
+	u8 coef[ZTS8032_COEF_LEN];
 	u32 c0, c1;
 	u32 c00, c10, c20, c30, c01, c11, c21;
 
 	/* Read all sensor calibration coefficients from the COEF registers. */
 	rc = regmap_bulk_read(data->regmap, DPS310_COEF_BASE, coef,
-			      sizeof(coef));
+			      data->info->coef_len);
 	if (rc < 0)
 		return rc;
 
@@ -194,6 +222,11 @@ static int dps310_get_coefs(struct dps310_data *data)
 	c30 = (coef[16] << 8) | coef[17];
 	data->c30 = sign_extend32(c30, 15);
 
+	if (data->info->coef_len == ZTS8032_COEF_LEN) {
+		data->c31 = sign_extend32((coef[18] << 8) | coef[19], 15);
+		data->c40 = sign_extend32((coef[20] << 8) | coef[21], 15);
+	}
+
 	return 0;
 }
 
@@ -251,10 +284,10 @@ static int dps310_startup(struct dps310_data *data)
 		return rc;
 
 	/*
-	 * Set up external (MEMS) temperature sensor in single sample, one
-	 * measurement per second mode
+	 * Set up the temperature sensor the coefficients are for in single
+	 * sample, one measurement per second mode
 	 */
-	rc = regmap_write(data->regmap, DPS310_TMP_CFG, DPS310_TMP_EXT);
+	rc = regmap_write(data->regmap, DPS310_TMP_CFG, data->info->tmp_cfg);
 	if (rc)
 		return rc;
 
@@ -682,6 +715,7 @@ static int dps310_calculate_pressure(struct dps310_data *data, int *val)
 	s64 ts;
 	s64 x2;
 	s64 x3;
+	s64 x4;
 
 	rc = dps310_get_pres_k(data, &kp);
 	if (rc)
@@ -702,6 +736,7 @@ static int dps310_calculate_pressure(struct dps310_data *data, int *val)
 	ts = div_s64(t * DPS310_Q_ONE, kt);
 	x2 = dps310_mul_q(ps, ps);
 	x3 = dps310_mul_q(x2, ps);
+	x4 = dps310_mul_q(x3, ps);
 
 	pressure = data->c00 * DPS310_Q_ONE;
 	pressure += div_s64(p * data->c10 * DPS310_Q_ONE, kp);
@@ -709,6 +744,8 @@ static int dps310_calculate_pressure(struct dps310_data *data, int *val)
 	pressure += dps310_mul_q(data->c11 * ps, ts);
 	pressure += data->c20 * x2 + data->c30 * x3;
 	pressure += dps310_mul_q(data->c21 * x2, ts);
+	/* ZTS8032 only, c31 and c40 are zero on the DPS310 */
+	pressure += data->c40 * x4 + dps310_mul_q(data->c31 * x3, ts);
 	pressure >>= DPS310_Q;
 	if (pressure < 0LL)
 		return -ERANGE;
@@ -983,7 +1020,11 @@ static int dps310_probe(struct i2c_client *client)
 	data->client = client;
 	mutex_init(&data->lock);
 
-	iio->name = DPS310_DEV_NAME;
+	data->info = i2c_get_match_data(client);
+	if (!data->info)
+		return -ENODEV;
+
+	iio->name = data->info->name;
 	iio->channels = dps310_channels;
 	iio->num_channels = ARRAY_SIZE(dps310_channels);
 	iio->info = &dps310_info;
@@ -1022,13 +1063,21 @@ static int dps310_probe(struct i2c_client *client)
 }
 
 static const struct i2c_device_id dps310_id[] = {
-	{ .name = DPS310_DEV_NAME },
+	{ .name = "dps310", .driver_data = (kernel_ulong_t)&dps310_chip_info },
+	{ .name = "zts8032", .driver_data = (kernel_ulong_t)&zts8032_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, dps310_id);
 
+static const struct of_device_id dps310_of_match[] = {
+	{ .compatible = "infineon,dps310", .data = &dps310_chip_info },
+	{ .compatible = "zilltek,zts8032", .data = &zts8032_chip_info },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, dps310_of_match);
+
 static const struct acpi_device_id dps310_acpi_match[] = {
-	{ "IFX3100" },
+	{ "IFX3100", (kernel_ulong_t)&dps310_chip_info },
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, dps310_acpi_match);
@@ -1036,6 +1085,7 @@ MODULE_DEVICE_TABLE(acpi, dps310_acpi_match);
 static struct i2c_driver dps310_driver = {
 	.driver = {
 		.name = DPS310_DEV_NAME,
+		.of_match_table = dps310_of_match,
 		.acpi_match_table = dps310_acpi_match,
 	},
 	.probe = dps310_probe,
-- 
2.55.0

Re: [PATCH 3/4] dt-bindings: iio: pressure: infineon,dps310: Add Zilltek ZTS8032

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 75 bytes --]

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 2/4] dt-bindings: vendor-prefixes: Add ZillTek Technology

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 1270 bytes --]

On Mon, Oct 12, 2026 at 02:45:48PM +0300, Paulius Zaleckas wrote:
> From: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> 
> ZillTek Technology Corp. (Hsinchu, Taiwan) makes MEMS microphones and
> barometric pressure sensors such as the ZTS8032.
> 
> Link: https://www.zilltek.com/

Great, love to see a link to the website, saves me googling them.

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

> Assisted-by: LLM
> Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index ba2002969373..255dc56edc36 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -1977,6 +1977,8 @@ patternProperties:
>      description: Shenzhen Zidoo Technology Co., Ltd.
>    "^zii,.*":
>      description: Zodiac Inflight Innovations
> +  "^zilltek,.*":
> +    description: ZillTek Technology Corp.
>    "^zinitix,.*":
>      description: Zinitix Co., Ltd
>    "^zkmagic,.*":
> -- 
> 2.55.0
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 4/4] iio: pressure: dps310: add Zilltek ZTS8032 support

[Andy Shevchenko]

On Mon, Oct 12, 2026 at 02:45:50PM +0300, Paulius Zaleckas wrote:

> The Zilltek ZTS8032 has the DPS310 register map, scale factors and
> compensation, with these differences:
> 
> - two more pressure coefficients, c31 and c40 at 0x22-0x25, adding
>   c40 * Praw_sc^4 + c31 * Traw_sc * Praw_sc^3 to the polynomial
> - TMP_EXT is MEAS_CFG bit 3, and the temperature coefficients are for
>   the internal sensor (COEF_SRCE reads 0x06). TMP_CFG bit 7 is the top
>   bit of a 4-bit TMP_RATE, so the DPS310 TMP_EXT write would select a
>   25/16 Hz background rate instead of the external sensor.
> - product ID 0x11 instead of 0x10, the driver does not check it
> 
> Add a per-chip table holding the coefficient count and the TMP_CFG
> startup value, and an OF match table to select it.
> 
> Tested on a ZTS8032 at 0x76 over I2C: in_pressure_input is within 1 Pa
> of the datasheet formula evaluated from the raw and coefficient
> registers at every oversampling rate from 1 to 128, and TMP_CFG reads
> 0x00 after probe.

...

>  #include <linux/math64.h>

> +#include <linux/mod_devicetable.h>

No. This should be guaranteed by the respective bus header.

>  #include <linux/module.h>
>  #include <linux/regmap.h>
>  #include <linux/unaligned.h>

...

> +	data->info = i2c_get_match_data(client);
> +	if (!data->info)
> +		return -ENODEV;

-ENODATA

...

>  static const struct i2c_device_id dps310_id[] = {
> -	{ .name = DPS310_DEV_NAME },
> +	{ .name = "dps310", .driver_data = (kernel_ulong_t)&dps310_chip_info },
> +	{ .name = "zts8032", .driver_data = (kernel_ulong_t)&zts8032_chip_info },

Using driver_data should be in a separate change.

>  	{ }
>  };
>  MODULE_DEVICE_TABLE(i2c, dps310_id);
>  
> +static const struct of_device_id dps310_of_match[] = {
> +	{ .compatible = "infineon,dps310", .data = &dps310_chip_info },
> +	{ .compatible = "zilltek,zts8032", .data = &zts8032_chip_info },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, dps310_of_match);

Adding OF table should be in a separate change.

...

Hence this patch should be split to three (or more if there are more logical
changes).

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH 4/4] iio: pressure: dps310: add Zilltek ZTS8032 support

[Uwe Kleine-König]

[-- Attachment #1: Type: text/plain, Size: 3232 bytes --]

On Mon, Oct 12, 2026 at 02:45:50PM +0300, Paulius Zaleckas wrote:
> From: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> 
> The Zilltek ZTS8032 has the DPS310 register map, scale factors and
> compensation, with these differences:
> 
> - two more pressure coefficients, c31 and c40 at 0x22-0x25, adding
>   c40 * Praw_sc^4 + c31 * Traw_sc * Praw_sc^3 to the polynomial
> - TMP_EXT is MEAS_CFG bit 3, and the temperature coefficients are for
>   the internal sensor (COEF_SRCE reads 0x06). TMP_CFG bit 7 is the top
>   bit of a 4-bit TMP_RATE, so the DPS310 TMP_EXT write would select a
>   25/16 Hz background rate instead of the external sensor.
> - product ID 0x11 instead of 0x10, the driver does not check it
> 
> Add a per-chip table holding the coefficient count and the TMP_CFG
> startup value, and an OF match table to select it.
> 
> Tested on a ZTS8032 at 0x76 over I2C: in_pressure_input is within 1 Pa
> of the datasheet formula evaluated from the raw and coefficient
> registers at every oversampling rate from 1 to 128, and TMP_CFG reads
> 0x00 after probe.
> 
> Assisted-by: LLM
> Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
> ---
>  drivers/iio/pressure/Kconfig  |  4 +--
>  drivers/iio/pressure/dps310.c | 66 ++++++++++++++++++++++++++++++-----
>  2 files changed, 60 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/iio/pressure/Kconfig b/drivers/iio/pressure/Kconfig
> index cef8b90b9ae7..e407243e131c 100644
> --- a/drivers/iio/pressure/Kconfig
> +++ b/drivers/iio/pressure/Kconfig
> @@ -115,8 +115,8 @@ config DPS310
>  	select IIO_BUFFER
>  	select IIO_TRIGGERED_BUFFER
>  	help
> -	  Support for the Infineon DPS310 digital barometric pressure sensor.
> -	  It can be accessed over I2C bus.
> +	  Support for the Infineon DPS310 and Zilltek ZTS8032 digital
> +	  barometric pressure sensors. They can be accessed over I2C bus.
>  
>  	  This driver can also be built as a module.  If so, the module will be
>  	  called dps310.
> diff --git a/drivers/iio/pressure/dps310.c b/drivers/iio/pressure/dps310.c
> index 3bc690cc8609..3b0f6d344409 100644
> --- a/drivers/iio/pressure/dps310.c
> +++ b/drivers/iio/pressure/dps310.c
> @@ -7,6 +7,10 @@
>   *
>   * https://www.infineon.com/dgdl/?fileId=5546d462576f34750157750826c42242
>   *
> + * The Zilltek ZTS8032 is register compatible, with two more pressure
> + * calibration coefficients (c31, c40) and temperature calibrated against
> + * the internal sensor.
> + *
>   * Temperature calculation:
>   *   c0 * 0.5 + c1 * T_raw / kT °C
>   *
> @@ -18,6 +22,7 @@
>  #include <linux/i2c.h>
>  #include <linux/limits.h>
>  #include <linux/math64.h>
> +#include <linux/mod_devicetable.h>

Adding that header mainly results in pulling in many unneeded
dependencies, so please don't.

of_device_id is already provided by <linux/i2c.h>, so you can just drop
the #include.

>  static const struct acpi_device_id dps310_acpi_match[] = {
> -	{ "IFX3100" },
> +	{ "IFX3100", (kernel_ulong_t)&dps310_chip_info },
>  	{ }
>  };

While touching that struct, please make this:

	{ .id = "IFX3100", .driver_data = (kernel_ulong_t)&dps310_chip_info },

Best regards
Uwe

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]