[PATCH v2 0/3] Add support for Variscite VAR-SOM-MX8QM and Symphony board

[PATCH v2 0/3] Add support for Variscite VAR-SOM-MX8QM and Symphony board

[Stefano Radaelli]

This patch series adds support for the Variscite VAR-SOM-MX8 QuadMax
system on module and the Symphony carrier board.

The series includes:
- SOM device tree with on-module peripherals
- Symphony carrier board device tree with board-specific features

The implementation follows the standard SOM + carrier board pattern
where the SOM dtsi contains only peripherals mounted on the module,
while carrier-specific interfaces are enabled in the board dts.

v1->v2:
 - Added non-removable property to usdhc3
 - Removed unused fec gpio pinctrl
 - Fix ptn5150 interrupt
 - Fix ecspi1 cs gpio

Stefano Radaelli (3):
  dt-bindings: arm: fsl: add Variscite VAR-SOM-MX8 QuadMax Boards
  arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax
  arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board

 .../devicetree/bindings/arm/fsl.yaml          |   6 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8qm-var-som-symphony.dts | 488 ++++++++++++++++
 .../boot/dts/freescale/imx8qm-var-som.dtsi    | 529 ++++++++++++++++++
 4 files changed, 1024 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi


base-commit: d0c222c2e2ce577d801bdf129dc6c078f29e22df
prerequisite-patch-id: 0996915f031a1d899202c5fba75a969d6ce2a53d
prerequisite-patch-id: dbed47ecb907f6b7f7e284c5c1a3c325566eafd7
prerequisite-patch-id: c758aa296e6effc94c30449cc7e4773f0ae02914
prerequisite-patch-id: 31784fa7a3ee5c178b2f1ffa97c1dd7c1d3d898a
prerequisite-patch-id: 5810f43cde9c24ee318d680c1852b3ded18f3aa0
prerequisite-patch-id: 012c9c8ba4e290532a1b7f8642274b7c5f252e03
prerequisite-patch-id: a57d576be42d5061bba453f0d5960132be55a1ff
prerequisite-patch-id: e34a75fb6f7e01455dd5ca734dacad66b12de06c
prerequisite-patch-id: cc7abadd0354d14bad0cac1fbacda14ab9d4e02b
prerequisite-patch-id: c0276686c0247cb2385c56b96cbfd6de5128415c
prerequisite-patch-id: 100c47538870af63194b407fae06183fee85fc09
prerequisite-patch-id: 3a3b3e40f5fba785857091dda909d22bfc5e2d0e
-- 
2.47.3

[PATCH v2 1/3] dt-bindings: arm: fsl: add Variscite VAR-SOM-MX8 QuadMax Boards

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

Add DT compatible strings for Variscite VAR-SOM-MX8 QuadMax SoM and
Variscite Symphony development carrier Board.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v1->v2:
 - 

 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 6237fb2ae50e..532e4308dc46 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1381,6 +1381,12 @@ properties:
               - fsl,imx8qm-mek-revd      # i.MX8QM MEK Rev D Board
           - const: fsl,imx8qm
 
+      - description: i.MX8QM Variscite VAR-SOM-MX8 based Boards
+        items:
+          - const: variscite,var-som-imx8qm-symphony
+          - const: variscite,var-som-imx8qm
+          - const: fsl,imx8qm
+
       - description: i.MX8QM Boards with Toradex Apalis iMX8 Modules
         items:
           - enum:
-- 
2.47.3

[PATCH v2 2/3] arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

Add device tree support for the Variscite VAR-SOM-MX8 QuadMax
system on module.
This SOM is designed to be used with various carrier boards.

The module includes:
- NXP i.MX8 QuadMax MPU processor
- Up to 8GB of LPDDR4 memory
- Up to 128GB of eMMC storage memory
- Integrated 10/100/1000 Mbps Ethernet Transceiver
- Codec audio WM8904
- WIFI6 dual-band 802.11ax/ac/a/b/g/n with optional 802.15.4 and Bluetooth

Only SOM-specific peripherals are enabled by default. Carrier board
specific interfaces are left disabled to be enabled in the respective
carrier board device trees.

Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8-quadmax-quadplus/var-som-mx8/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v1->v2:
 - Added non-removable property to usdhc3
 - Removed unused fec gpio pinctrl

 .../boot/dts/freescale/imx8qm-var-som.dtsi    | 529 ++++++++++++++++++
 1 file changed, 529 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi

diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
new file mode 100644
index 000000000000..e805c51eb27d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
@@ -0,0 +1,529 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common dtsi for Variscite VAR-SOM-MX8
+ *
+ * Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8-quadmax-quadplus/var-som-mx8/
+ *
+ * Copyright (C) 2026 Variscite Ltd. - https://www.variscite.com/
+ *
+ */
+
+/dts-v1/;
+
+#include "imx8qm.dtsi"
+
+/ {
+	model = "Variscite i.MX8QM VAR-SOM-MX8 Module";
+	compatible = "variscite,var-som-imx8qm", "fsl,imx8qm";
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x40000000>;
+	};
+
+	reg_audio_supply: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "wm8904-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_phy_vddio: regulator-phy-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		vdev0vring0: memory@90000000 {
+			reg = <0 0x90000000 0 0x8000>;
+			no-map;
+		};
+
+		vdev0vring1: memory@90008000 {
+			reg = <0 0x90008000 0 0x8000>;
+			no-map;
+		};
+
+		vdev1vring0: memory@90010000 {
+			reg = <0 0x90010000 0 0x8000>;
+			no-map;
+		};
+
+		vdev1vring1: memory@90018000 {
+			reg = <0 0x90018000 0 0x8000>;
+			no-map;
+		};
+
+		rsc_table0: memory@900ff000 {
+			reg = <0 0x900ff000 0 0x1000>;
+			no-map;
+		};
+
+		vdev2vring0: memory@90100000 {
+			reg = <0 0x90100000 0 0x8000>;
+			no-map;
+		};
+
+		vdev2vring1: memory@90108000 {
+			reg = <0 0x90108000 0 0x8000>;
+			no-map;
+		};
+
+		vdev3vring0: memory@90110000 {
+			reg = <0 0x90110000 0 0x8000>;
+			no-map;
+		};
+
+		vdev3vring1: memory@90118000 {
+			reg = <0 0x90118000 0 0x8000>;
+			no-map;
+		};
+
+		rsc_table1: memory@901ff000 {
+			reg = <0 0x901ff000 0 0x1000>;
+			no-map;
+		};
+
+		vdevbuffer: memory@90400000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x90400000 0 0x100000>;
+			no-map;
+		};
+
+		dsp_reserved: memory@92400000 {
+			reg = <0 0x92400000 0 0x1000000>;
+			no-map;
+		};
+
+		dsp_vdev0vring0: memory@942f0000 {
+			reg = <0 0x942f0000 0 0x8000>;
+			no-map;
+		};
+
+		dsp_vdev0vring1: memory@942f8000 {
+			reg = <0 0x942f8000 0 0x8000>;
+			no-map;
+		};
+
+		dsp_vdev0buffer: memory@94300000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x94300000 0 0x100000>;
+			no-map;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0 0xc0000000 0 0x3c000000>;
+			size = <0 0x3c000000>;
+			linux,cma-default;
+			reusable;
+		};
+	};
+
+	sound-wm8904 {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,name = "wm8904-audio";
+		simple-audio-card,routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"IN1L", "Microphone Jack",
+			"IN1R", "Microphone Jack";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Line", "Line In Jack";
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&wm8904>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&esai0>;
+		};
+	};
+};
+
+&acm {
+	status = "okay";
+};
+
+&asrc0 {
+	fsl,asrc-rate  = <48000>;
+	status = "okay";
+};
+
+&asrc1 {
+	fsl,asrc-rate = <48000>;
+	status = "okay";
+};
+
+&cm41_intmux {
+	status = "okay";
+};
+
+&esai0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esai0>;
+	#sound-dai-cells = <0>;
+	assigned-clocks = <&acm IMX_ADMA_ACM_ESAI0_MCLK_SEL>,
+			<&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+			<&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+			<&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+			<&esai0_lpcg 0>;
+	assigned-clock-parents = <&aud_pll_div0_lpcg 0>;
+	assigned-clock-rates = <0>, <786432000>, <49152000>, <24576000>, <49152000>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	/*
+	 * The required RGMII TX and RX 2ns delays are implemented directly
+	 * in hardware via passive delay elements on the SOM PCB.
+	 * No delay configuration is needed in software via PHY driver.
+	 */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@4 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <4>;
+			reset-gpios = <&lsio_gpio2 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <20000>;
+			vddio-supply = <&reg_phy_vddio>;
+		};
+	};
+};
+
+&gpio0_mipi_csi0 {
+	status = "disabled";
+};
+
+&gpio0_mipi_csi1 {
+	status = "disabled";
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c0>;
+	status = "okay";
+
+	wm8904: codec@1a {
+		compatible = "wlf,wm8904";
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+		clocks = <&mclkout0_lpcg 0>;
+		clock-names = "mclk";
+		assigned-clocks = <&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_PLL>,
+				<&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_SLV_BUS>,
+				<&clk IMX_SC_R_AUDIO_PLL_0 IMX_SC_PM_CLK_MST_BUS>,
+				<&mclkout0_lpcg 0>;
+		assigned-clock-rates = <786432000>, <49152000>, <12288000>, <12288000>;
+		AVDD-supply = <&reg_audio_supply>;
+		CPVDD-supply = <&reg_audio_supply>;
+		DBVDD-supply = <&reg_audio_supply>;
+		DCVDD-supply = <&reg_audio_supply>;
+		MICVDD-supply = <&reg_audio_supply>;
+		wlf,drc-cfg-names = "default", "peaklimiter", "tradition",
+				    "soft", "music";
+		/*
+		 * Config registers per name, respectively:
+		 * KNEE_IP = 0,   KNEE_OP = 0,     HI_COMP = 1,   LO_COMP = 1
+		 * KNEE_IP = -24, KNEE_OP = -6,    HI_COMP = 1/4, LO_COMP = 1
+		 * KNEE_IP = -42, KNEE_OP = -3,    HI_COMP = 0,   LO_COMP = 1
+		 * KNEE_IP = -45, KNEE_OP = -9,    HI_COMP = 1/8, LO_COMP = 1
+		 * KNEE_IP = -30, KNEE_OP = -10.5, HI_COMP = 1/4, LO_COMP = 1
+		 */
+		wlf,drc-cfg-regs = /bits/ 16 <0x01af 0x3248 0x0000 0x0000>,
+				   /bits/ 16 <0x04af 0x324b 0x0010 0x0408>,
+				   /bits/ 16 <0x04af 0x324b 0x0028 0x0704>,
+				   /bits/ 16 <0x04af 0x324b 0x0018 0x078c>,
+				   /bits/ 16 <0x04af 0x324b 0x0010 0x050e>;
+		/* GPIO1 = DMIC_CLK, don't touch others */
+		wlf,gpio-cfg = <0x0018>, <0xffff>, <0xffff>, <0xffff>;
+	};
+};
+
+/* Bluetooth */
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&mu_m0{
+	status = "okay";
+};
+
+&mu1_m0{
+	status = "okay";
+};
+
+&mu2_m0{
+	status = "okay";
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sai6 {
+	assigned-clocks = <&acm IMX_ADMA_ACM_SAI6_MCLK_SEL>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+			<&sai6_lpcg 0>;
+	assigned-clock-parents = <&aud_pll_div1_lpcg 0>;
+	assigned-clock-rates = <0>, <786432000>, <98304000>, <24576000>, <98304000>;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
+&sai7 {
+	assigned-clocks = <&acm IMX_ADMA_ACM_SAI7_MCLK_SEL>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_PLL>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_SLV_BUS>,
+			<&clk IMX_SC_R_AUDIO_PLL_1 IMX_SC_PM_CLK_MST_BUS>,
+			<&sai7_lpcg 0>;
+	assigned-clock-parents = <&aud_pll_div1_lpcg 0>;
+	assigned-clock-rates = <0>, <786432000>, <98304000>, <24576000>, <98304000>;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
+&thermal_zones {
+	pmic-thermal {
+		polling-delay-passive = <250>;
+		polling-delay = <2000>;
+		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
+		trips {
+			pmic_alert0: trip0 {
+				temperature = <110000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+			pmic_crit0: trip1 {
+				temperature = <125000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+		cooling-maps {
+			map0 {
+				trip = <&pmic_alert0>;
+				cooling-device = <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						 <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						 <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						 <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+/* eMMC */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+/* WIFI */
+&usdhc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_esai0: esai0grp {
+		fsl,pins = <
+			IMX8QM_ESAI0_FSR_AUD_ESAI0_FSR				0xc6000040
+			IMX8QM_ESAI0_FST_AUD_ESAI0_FST				0xc6000040
+			IMX8QM_ESAI0_SCKR_AUD_ESAI0_SCKR			0xc6000040
+			IMX8QM_ESAI0_SCKT_AUD_ESAI0_SCKT			0xc6000040
+			IMX8QM_ESAI0_TX0_AUD_ESAI0_TX0				0xc6000040
+			IMX8QM_ESAI0_TX5_RX0_AUD_ESAI0_TX5_RX0			0xc6000040
+			IMX8QM_MCLK_OUT0_AUD_ESAI0_TX_HF_CLK			0xc600004c
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			IMX8QM_ENET0_MDC_CONN_ENET0_MDC				0x06000048
+			IMX8QM_ENET0_MDIO_CONN_ENET0_MDIO			0x06000048
+			IMX8QM_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x06000048
+			IMX8QM_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC		0x06000048
+			IMX8QM_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x06000048
+			IMX8QM_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x06000048
+			IMX8QM_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x06000048
+			IMX8QM_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x06000048
+			IMX8QM_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC		0x06000048
+			IMX8QM_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x06000048
+			IMX8QM_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x06000048
+			IMX8QM_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x06000048
+			IMX8QM_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x06000048
+			IMX8QM_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x06000048
+			IMX8QM_ESAI0_TX2_RX3_LSIO_GPIO2_IO28			0x06000028
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			IMX8QM_ESAI1_FSR_LSIO_GPIO2_IO04			0x00000041
+			IMX8QM_ESAI1_FST_LSIO_GPIO2_IO05			0x00000041
+			IMX8QM_ESAI1_SCKR_LSIO_GPIO2_IO06			0x00000041
+			IMX8QM_ESAI1_SCKT_LSIO_GPIO2_IO07			0x00000041
+			IMX8QM_SPDIF0_EXT_CLK_LSIO_GPIO2_IO16			0x00000041
+		>;
+	};
+
+	pinctrl_i2c0: i2c0grp {
+		fsl,pins = <
+			IMX8QM_HDMI_TX0_TS_SCL_DMA_I2C0_SCL			0xc6000020
+			IMX8QM_HDMI_TX0_TS_SDA_DMA_I2C0_SDA			0xc6000020
+		>;
+	};
+
+	pinctrl_lpuart1: lpuart1grp {
+		fsl,pins = <
+			IMX8QM_UART1_RX_DMA_UART1_RX				0x06000020
+			IMX8QM_UART1_TX_DMA_UART1_TX				0x06000020
+			IMX8QM_UART1_CTS_B_DMA_UART1_RTS_B			0x06000020
+			IMX8QM_UART1_RTS_B_DMA_UART1_CTS_B			0x06000020
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK				0x06000041
+			IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD				0x00000021
+			IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000021
+			IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000021
+			IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000021
+			IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000021
+			IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000021
+			IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000021
+			IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000021
+			IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000021
+			IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE			0x06000041
+			IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B			0x00000021
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK				0x06000040
+			IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD				0x00000020
+			IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020
+			IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020
+			IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020
+			IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020
+			IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020
+			IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020
+			IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020
+			IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020
+			IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE			0x06000040
+			IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B			0x00000020
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			IMX8QM_EMMC0_CLK_CONN_EMMC0_CLK				0x06000040
+			IMX8QM_EMMC0_CMD_CONN_EMMC0_CMD				0x00000020
+			IMX8QM_EMMC0_DATA0_CONN_EMMC0_DATA0			0x00000020
+			IMX8QM_EMMC0_DATA1_CONN_EMMC0_DATA1			0x00000020
+			IMX8QM_EMMC0_DATA2_CONN_EMMC0_DATA2			0x00000020
+			IMX8QM_EMMC0_DATA3_CONN_EMMC0_DATA3			0x00000020
+			IMX8QM_EMMC0_DATA4_CONN_EMMC0_DATA4			0x00000020
+			IMX8QM_EMMC0_DATA5_CONN_EMMC0_DATA5			0x00000020
+			IMX8QM_EMMC0_DATA6_CONN_EMMC0_DATA6			0x00000020
+			IMX8QM_EMMC0_DATA7_CONN_EMMC0_DATA7			0x00000020
+			IMX8QM_EMMC0_STROBE_CONN_EMMC0_STROBE			0x06000040
+			IMX8QM_EMMC0_RESET_B_CONN_EMMC0_RESET_B			0x00000020
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000041
+			IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000021
+			IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0			0x00000021
+			IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1			0x00000021
+			IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2			0x00000021
+			IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3			0x00000021
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3100mhzgrp {
+		fsl,pins = <
+			IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000040
+			IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000020
+			IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0			0x00000020
+			IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1			0x00000020
+			IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2			0x00000020
+			IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3			0x00000020
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			IMX8QM_USDHC2_CLK_CONN_USDHC2_CLK			0x06000040
+			IMX8QM_USDHC2_CMD_CONN_USDHC2_CMD			0x00000020
+			IMX8QM_USDHC2_DATA0_CONN_USDHC2_DATA0			0x00000020
+			IMX8QM_USDHC2_DATA1_CONN_USDHC2_DATA1			0x00000020
+			IMX8QM_USDHC2_DATA2_CONN_USDHC2_DATA2			0x00000020
+			IMX8QM_USDHC2_DATA3_CONN_USDHC2_DATA3			0x00000020
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K	0xc600004c
+			IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31			0x06000021
+			IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30			0x00000021
+			IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26			0x00000021
+		>;
+	};
+};
-- 
2.47.3

[PATCH v2 3/3] arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board

[Stefano Radaelli]

From: Stefano Radaelli <stefano.r@variscite.com>

Add device tree support for the Variscite Symphony carrier board with
the VAR-SOM-MX8 QuadMax system on module.

The Symphony board includes
- uSD Card support
- USB ports and OTG
- Additional Gigabit Ethernet interface
- Uart, SPI and I2C interfaces
- GPIO Expanders
- RTC module
- TPM module
- CAN peripherals
- PCIE support

Link: https://variscite.com/carrier-boards/symphony-board/
Signed-off-by: Stefano Radaelli <stefano.r@variscite.com>
---
v1->v2:
 - Fix ptn5150 interrupt
 - Fix ecspi1 cs gpio

 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8qm-var-som-symphony.dts | 488 ++++++++++++++++++
 2 files changed, 489 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 430085123b4e..ceb31556a8c0 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -540,6 +540,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-apalis-v1.1-ixora-v1.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-tqma8qm-mba8x.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8qm-var-som-symphony.dtb
 
 imx8qm-mek-ov5640-csi0-dtbs := imx8qm-mek.dtb imx8qm-mek-ov5640-csi0.dtbo
 dtb-${CONFIG_ARCH_MXC} += imx8qm-mek-ov5640-csi0.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
new file mode 100644
index 000000000000..bf6678637830
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
@@ -0,0 +1,488 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Variscite Symphony carrier board for VAR-SOM-MX8 QuadMax
+ *
+ * Link: https://variscite.com/carrier-boards/symphony-board/
+ *
+ * Copyright (C) 2026 Variscite Ltd. - https://www.variscite.com/
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "imx8qm-var-som.dtsi"
+
+/ {
+	model = "Variscite VAR-SOM-MX8 on Symphony evaluation board";
+	compatible = "variscite,var-som-imx8qm-symphony",
+		     "variscite,var-som-imx8qm", "fsl,imx8qm";
+	chosen {
+		stdout-path = &lpuart0;
+	};
+
+	 gpio-keys {
+		compatible = "gpio-keys";
+
+		button-back {
+			label = "Back";
+			gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_BACK>;
+		};
+
+		button-home {
+			label = "Home";
+			gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+		};
+
+		button-menu {
+			label = "Menu";
+			gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MENU>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		led-hearthbeat {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_fec_phy: regulator-fec-phy {
+		compatible = "regulator-fixed";
+		regulator-name = "fec-phy";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-enable-ramp-delay = <20000>;
+		vin-supply = <&reg_vselect>;
+		gpio = <&pca9534 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&lsio_gpio0 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "sw-3p3-sd1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_vselect: regulator-vselect {
+		compatible = "regulator-fixed";
+		regulator-name = "reg_vselect";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&pca9534 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ethphy0 {
+	leds {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_LAN;
+			linux,default-trigger = "netdev";
+		};
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_LAN;
+			linux,default-trigger = "netdev";
+		};
+	};
+};
+
+&fec1 {
+	mdio {
+		ethphy1: ethernet-phy@5 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <5>;
+			vddio-supply = <&reg_phy_vddio>;
+			reset-gpios = <&pca9534 5 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <100000>;
+
+			leds {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				led@0 {
+					reg = <0>;
+					color = <LED_COLOR_ID_YELLOW>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+
+				led@1 {
+					reg = <1>;
+					color = <LED_COLOR_ID_GREEN>;
+					function = LED_FUNCTION_LAN;
+					linux,default-trigger = "netdev";
+				};
+			};
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec2>;
+	/*
+	 * The required RGMII TX and RX 2ns delays are implemented directly
+	 * in hardware via passive delay elements on the SOM PCB.
+	 * No delay configuration is needed in software via PHY driver.
+	 */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_fec_phy>;
+	status = "okay";
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&hsio_phy {
+	fsl,hsio-cfg = "pciea-pcieb-sata";
+	fsl,refclk-pad-mode = "input";
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9534: gpio@20 {
+		compatible = "nxp,pca9534";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9534>;
+		interrupt-parent = <&lsio_gpio1>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	/* USB Type-C Controller */
+	typec_ptn5150: typec@3d {
+		compatible = "nxp,ptn5150";
+		reg = <0x3d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ptn5150>;
+		interrupt-parent = <&lsio_gpio3>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+
+		port {
+			typec_dr_sw: endpoint {
+				remote-endpoint = <&usb3_drd_sw>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	pca6408: gpio@21 {
+		compatible = "nxp,pcal6408";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		/* RGB_SEL */
+		lvds-brg-enable-hog {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "lvds_brg_en";
+		};
+	};
+
+	st33ktpm2xi2c: tpm@2e {
+		compatible = "st,st33ktpm2xi2c", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+		label = "tpm";
+		reset-gpios = <&pca6408 4 GPIO_ACTIVE_LOW>;
+	};
+
+	/* Capacitive touch */
+	ft5x06_ts: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		pinctrl-names = "default";
+		reg = <0x38>;
+		pinctrl-0 = <&pinctrl_captouch>;
+		interrupt-parent = <&lsio_gpio0>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		wakeup-source;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1337";
+		reg = <0x68>;
+	};
+};
+
+&lpspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpspi1>;
+	cs-gpios = <&lsio_gpio3 24 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+/* console */
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+/* header */
+&lpuart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart2>;
+	status = "okay";
+};
+
+&pca9534 {
+	usb3-signal-route-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "usb3_signal_route";
+	};
+};
+
+&pciea{
+	phys = <&hsio_phy 0 PHY_TYPE_PCIE 0>;
+	phy-names = "pcie-phy";
+	reset-gpio = <&pca6408 1 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg3 {
+	status = "okay";
+};
+
+&usbotg3_cdns3 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb3_drd_sw: endpoint {
+			remote-endpoint = <&typec_dr_sw>;
+		};
+	};
+};
+
+&usbphy1 {
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&lsio_gpio0 14 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_captouch: captouchgrp {
+		fsl,pins = <
+			IMX8QM_GPT1_COMPARE_LSIO_GPIO0_IO19			0x06000021
+			IMX8QM_GPT0_COMPARE_LSIO_GPIO0_IO16			0x06000021
+		>;
+	};
+
+	pinctrl_fec2: fec2grp {
+		fsl,pins = <
+			IMX8QM_ENET1_RGMII_TX_CTL_CONN_ENET1_RGMII_TX_CTL	0x06000048
+			IMX8QM_ENET1_RGMII_TXC_CONN_ENET1_RGMII_TXC		0x06000048
+			IMX8QM_ENET1_RGMII_TXD0_CONN_ENET1_RGMII_TXD0		0x06000048
+			IMX8QM_ENET1_RGMII_TXD1_CONN_ENET1_RGMII_TXD1		0x06000048
+			IMX8QM_ENET1_RGMII_TXD2_CONN_ENET1_RGMII_TXD2		0x06000048
+			IMX8QM_ENET1_RGMII_TXD3_CONN_ENET1_RGMII_TXD3		0x06000048
+			IMX8QM_ENET1_RGMII_RXC_CONN_ENET1_RGMII_RXC		0x06000048
+			IMX8QM_ENET1_RGMII_RX_CTL_CONN_ENET1_RGMII_RX_CTL	0x06000048
+			IMX8QM_ENET1_RGMII_RXD0_CONN_ENET1_RGMII_RXD0		0x06000048
+			IMX8QM_ENET1_RGMII_RXD1_CONN_ENET1_RGMII_RXD1		0x06000048
+			IMX8QM_ENET1_RGMII_RXD2_CONN_ENET1_RGMII_RXD2		0x06000048
+			IMX8QM_ENET1_RGMII_RXD3_CONN_ENET1_RGMII_RXD3		0x06000048
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan0grp {
+		fsl,pins = <
+			IMX8QM_FLEXCAN0_TX_DMA_FLEXCAN0_TX			0x00000021
+			IMX8QM_FLEXCAN0_RX_DMA_FLEXCAN0_RX			0x00000021
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan1grp {
+		fsl,pins = <
+			IMX8QM_FLEXCAN1_TX_DMA_FLEXCAN1_TX			0x00000021
+			IMX8QM_FLEXCAN1_RX_DMA_FLEXCAN1_RX			0x00000021
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			IMX8QM_USB_SS3_TC3_DMA_I2C1_SDA				0xc6000020
+			IMX8QM_USB_SS3_TC1_DMA_I2C1_SCL				0xc6000020
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			IMX8QM_ENET1_MDC_DMA_I2C4_SCL				0xc6000020
+			IMX8QM_ENET1_MDIO_DMA_I2C4_SDA				0xc6000020
+		>;
+	};
+
+	pinctrl_lpspi1: lpspi1grp {
+		fsl,pins = <
+			IMX8QM_ADC_IN3_DMA_SPI1_SCK				0x0600004c
+			IMX8QM_ADC_IN4_DMA_SPI1_SDO				0x0600004c
+			IMX8QM_ADC_IN5_DMA_SPI1_SDI				0x0600004c
+			IMX8QM_ADC_IN6_LSIO_GPIO3_IO24				0x00000021
+		>;
+	};
+
+	pinctrl_lpuart0: lpuart0grp {
+		fsl,pins = <
+			IMX8QM_UART0_RX_DMA_UART0_RX				0x06000020
+			IMX8QM_UART0_TX_DMA_UART0_TX				0x06000020
+		>;
+	};
+
+	pinctrl_lpuart2: lpuart2grp {
+		fsl,pins = <
+			IMX8QM_LVDS0_I2C1_SCL_DMA_UART2_TX			0x06000020
+			IMX8QM_LVDS0_I2C1_SDA_DMA_UART2_RX			0x06000020
+		>;
+	};
+
+	pinctrl_pca9534: pca9534grp {
+		fsl,pins = <
+			IMX8QM_MIPI_CSI0_MCLK_OUT_LSIO_GPIO1_IO24		0x00000021
+		>;
+	};
+
+	pinctrl_ptn5150: ptn5150grp {
+		fsl,pins = <
+			IMX8QM_SPI2_CS1_LSIO_GPIO3_IO11				0x00000021
+		>;
+	};
+
+	pinctrl_usbotg1: otg1grp {
+		fsl,pins = <
+			IMX8QM_GPT1_CAPTURE_LSIO_GPIO0_IO18			0x06000048
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000041
+			IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000021
+			IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0			0x00000021
+			IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1			0x00000021
+			IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2			0x00000021
+			IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3			0x00000021
+			IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000021
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040
+			IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020
+			IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0			0x00000020
+			IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1			0x00000020
+			IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2			0x00000020
+			IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3			0x00000020
+			IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000020
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			IMX8QM_USDHC1_CLK_CONN_USDHC1_CLK			0x06000040
+			IMX8QM_USDHC1_CMD_CONN_USDHC1_CMD			0x00000020
+			IMX8QM_USDHC1_DATA0_CONN_USDHC1_DATA0			0x00000020
+			IMX8QM_USDHC1_DATA1_CONN_USDHC1_DATA1			0x00000020
+			IMX8QM_USDHC1_DATA2_CONN_USDHC1_DATA2			0x00000020
+			IMX8QM_USDHC1_DATA3_CONN_USDHC1_DATA3			0x00000020
+			IMX8QM_USDHC1_VSELECT_CONN_USDHC1_VSELECT		0x00000020
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <
+			IMX8QM_GPT0_CLK_LSIO_GPIO0_IO14				0x00000021
+		>;
+	};
+};
-- 
2.47.3

Re: [PATCH v2 2/3] arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [High] The PMIC thermal zone's cooling map omits the high-power Cortex-A72 cores, severely limiting thermal mitigation.
- [Medium] WiFi and Bluetooth enable/reset GPIOs are configured in pinctrl but never bound to a driver, breaking power management and suspend/resume.
--

--- Patch [2]: [PATCH v2 2/3] arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax ---
commit 33df8d987b7061b5d0c8453d1a7834088b34ace9
Author: Stefano Radaelli <stefano.r@variscite.com>

arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax

Add device tree support for the Variscite VAR-SOM-MX8 QuadMax system on
module. This SOM includes an i.MX8 QuadMax processor, RAM, eMMC, Ethernet,
audio codec, and WiFi/Bluetooth.

Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8-quadmax-quadplus/var-som-mx8/

> diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
> new file mode 100644
> index 0000000000000..e805c51eb27df
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
[ ... ]
> +/* Bluetooth */
> +&lpuart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpuart1>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};

[Severity: Medium]
Since this UART is used for Bluetooth, should it have a serdev child node
(like compatible = "brcm,bcm4329-bt") with an 'enable-gpios' property?

Without an explicit driver binding to manage the module, the Bluetooth
device's power state cannot be controlled across suspend and resume.

[ ... ]
> +&thermal_zones {
> +	pmic-thermal {
> +		polling-delay-passive = <250>;
> +		polling-delay = <2000>;
> +		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
> +		trips {
> +			pmic_alert0: trip0 {
> +				temperature = <110000>;
> +				hysteresis = <2000>;
> +				type = "passive";
> +			};
> +			pmic_crit0: trip1 {
> +				temperature = <125000>;
> +				hysteresis = <2000>;
> +				type = "critical";
> +			};
> +		};
> +		cooling-maps {
> +			map0 {
> +				trip = <&pmic_alert0>;
> +				cooling-device = <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						 <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						 <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						 <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};

[Severity: High]
Is it intentional to omit the Cortex-A72 cores (<&A72_0> and <&A72_1>) from
this cooling map?

By only throttling the A53 cores during an overheat scenario, the system might
fail to cool the PMIC sufficiently. This increases the risk of reaching the
125°C threshold and triggering a hardware thermal shutdown.

> +		};
> +	};
> +};
[ ... ]
> +/* WIFI */
> +&usdhc3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> +	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi>;
> +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi>;
> +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	brcmf: wifi@1 {
> +		compatible = "brcm,bcm4329-fmac";
> +		reg = <1>;
> +	};
> +};

[ ... ]
> +	pinctrl_wifi: wifigrp {
> +		fsl,pins = <
> +			IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K	0xc600004c
> +			IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31			0x06000021
> +			IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30			0x00000021
> +			IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26			0x00000021
> +		>;
> +	};
> +};

[Severity: Medium]
Are these WiFi enable/reset GPIOs left uncontrolled without an active driver
binding?

While pinctrl_wifi is attached to usdhc3, there is no mmc-pwrseq node
consuming these GPIOs to control the power and reset sequencing. Relying on
the bootloader for initialization prevents the kernel from managing the power
state during suspend and resume.

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/cover.1784059139.git.stefano.r@variscite.com?part=2

Re: [PATCH v2 3/3] arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 4 potential issue(s) to consider:
- [Medium] The capacitive touch panel node `ft5x06_ts` lacks a `reset-gpios` (or `wake-gpios`) property, stranding a configured pinctrl pad and potentially causing probing failures.
- [Medium] The pinctrl for the USB VBUS regulator GPIO is incorrectly assigned to the USB controller node instead of the regulator node.
- [Low] The PCIe node uses the deprecated `reset-gpio` property instead of `reset-gpios`.
- [Low] The LED node name `led-hearthbeat` contains a typo.
--

--- Patch [3]: [PATCH v2 3/3] arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board ---
commit f84a05986e6ac58f10d1a6e2091672e4f1bf919b
Author: Stefano Radaelli <stefano.r@variscite.com>

arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board

This commit adds device tree support for the Variscite Symphony carrier board
with the VAR-SOM-MX8 QuadMax system on module. It configures interfaces
including SD card, USB, Ethernet, I2C, SPI, RTC, TPM, CAN, and PCIe.

Link: https://variscite.com/carrier-boards/symphony-board/

> diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
> new file mode 100644
> index 0000000000000..bf66786378301
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
[ ... ]
> +	gpio-leds {
> +		compatible = "gpio-leds";
> +
> +		led-hearthbeat {

[Severity: Low]
This isn't a bug, but there is a typo in the node name (hearthbeat instead
of heartbeat).

> +			function = LED_FUNCTION_STATUS;
> +			color = <LED_COLOR_ID_GREEN>;
> +			gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
[ ... ]
> +	/* Capacitive touch */
> +	ft5x06_ts: touchscreen@38 {
> +		compatible = "edt,edt-ft5406";
> +		pinctrl-names = "default";
> +		reg = <0x38>;
> +		pinctrl-0 = <&pinctrl_captouch>;
> +		interrupt-parent = <&lsio_gpio0>;
> +		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> +		touchscreen-size-x = <800>;
> +		touchscreen-size-y = <480>;
> +		touchscreen-inverted-x;
> +		touchscreen-inverted-y;
> +		wakeup-source;
> +	};

[Severity: Medium]
Is this touchscreen node missing a reset-gpios property?

The pinctrl_captouch group configures LSIO_GPIO0_IO16 for the touch
controller, but it is not assigned to reset-gpios here. 

Will the edt-ft5406 driver be able to toggle the reset line without it, or
could this lead to initialization failures?

[ ... ]
> +&pciea{
> +	phys = <&hsio_phy 0 PHY_TYPE_PCIE 0>;
> +	phy-names = "pcie-phy";
> +	reset-gpio = <&pca6408 1 GPIO_ACTIVE_LOW>;

[Severity: Low]
Should this use reset-gpios instead of the deprecated reset-gpio property?

> +	status = "okay";
> +};
[ ... ]
> +&usbotg1 {
> +	dr_mode = "host";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg1>;
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	srp-disable;
> +	hnp-disable;
> +	adp-disable;
> +	disable-over-current;
> +	status = "okay";
> +};

[Severity: Medium]
Is pinctrl_usbotg1 assigned to the wrong node?

The reg_usb_otg1_vbus regulator uses the GPIO to provide power, but the
pinctrl to configure the pad is placed here on the usbotg1 controller.

Could this cause the GPIO pad to be incorrectly muxed when the fixed
regulator framework tries to enable power before the USB driver probes?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/cover.1784059139.git.stefano.r@variscite.com?part=3

Re: [PATCH v2 2/3] arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax

[Frank Li]

On Tue, Jul 14, 2026 at 08:17:02PM +0000, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
> - [High] The PMIC thermal zone's cooling map omits the high-power Cortex-A72 cores, severely limiting thermal mitigation.
> - [Medium] WiFi and Bluetooth enable/reset GPIOs are configured in pinctrl but never bound to a driver, breaking power management and suspend/resume.
> --
>
> --- Patch [2]: [PATCH v2 2/3] arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax ---
> commit 33df8d987b7061b5d0c8453d1a7834088b34ace9
> Author: Stefano Radaelli <stefano.r@variscite.com>
>
> arm64: dts: freescale: Add support for Variscite VAR-SOM-MX8 QuadMax
>
> Add device tree support for the Variscite VAR-SOM-MX8 QuadMax system on
> module. This SOM includes an i.MX8 QuadMax processor, RAM, eMMC, Ethernet,
> audio codec, and WiFi/Bluetooth.
>
> Link: https://variscite.com/system-on-module-som/i-mx-8/i-mx-8-quadmax-quadplus/var-som-mx8/
>
> > diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
> > new file mode 100644
> > index 0000000000000..e805c51eb27df
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som.dtsi
> [ ... ]
> > +/* Bluetooth */
> > +&lpuart1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_lpuart1>;
> > +	uart-has-rtscts;
> > +	status = "okay";
> > +};
>
> [Severity: Medium]
> Since this UART is used for Bluetooth, should it have a serdev child node
> (like compatible = "brcm,bcm4329-bt") with an 'enable-gpios' property?
>
> Without an explicit driver binding to manage the module, the Bluetooth
> device's power state cannot be controlled across suspend and resume.
>
> [ ... ]
> > +&thermal_zones {
> > +	pmic-thermal {
> > +		polling-delay-passive = <250>;
> > +		polling-delay = <2000>;
> > +		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
> > +		trips {
> > +			pmic_alert0: trip0 {
> > +				temperature = <110000>;
> > +				hysteresis = <2000>;
> > +				type = "passive";
> > +			};
> > +			pmic_crit0: trip1 {
> > +				temperature = <125000>;
> > +				hysteresis = <2000>;
> > +				type = "critical";
> > +			};
> > +		};
> > +		cooling-maps {
> > +			map0 {
> > +				trip = <&pmic_alert0>;
> > +				cooling-device = <&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > +						 <&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > +						 <&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > +						 <&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> > +			};
>
> [Severity: High]
> Is it intentional to omit the Cortex-A72 cores (<&A72_0> and <&A72_1>) from
> this cooling map?
>
> By only throttling the A53 cores during an overheat scenario, the system might
> fail to cool the PMIC sufficiently. This increases the risk of reaching the
> 125°C threshold and triggering a hardware thermal shutdown.
>
> > +		};
> > +	};
> > +};
> [ ... ]
> > +/* WIFI */
> > +&usdhc3 {
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> > +	pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > +	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi>;
> > +	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi>;
> > +	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi>;
> > +	bus-width = <4>;
> > +	non-removable;
> > +	status = "okay";
> > +
> > +	brcmf: wifi@1 {
> > +		compatible = "brcm,bcm4329-fmac";
> > +		reg = <1>;
> > +	};
> > +};
>
> [ ... ]
> > +	pinctrl_wifi: wifigrp {
> > +		fsl,pins = <
> > +			IMX8QM_SCU_GPIO0_07_SCU_DSC_RTC_CLOCK_OUTPUT_32K	0xc600004c
> > +			IMX8QM_SCU_GPIO0_03_LSIO_GPIO0_IO31			0x06000021
> > +			IMX8QM_SCU_GPIO0_02_LSIO_GPIO0_IO30			0x00000021
> > +			IMX8QM_QSPI1A_DATA0_LSIO_GPIO4_IO26			0x00000021
> > +		>;
> > +	};
> > +};
>
> [Severity: Medium]
> Are these WiFi enable/reset GPIOs left uncontrolled without an active driver
> binding?
>
> While pinctrl_wifi is attached to usdhc3, there is no mmc-pwrseq node
> consuming these GPIOs to control the power and reset sequencing. Relying on
> the bootloader for initialization prevents the kernel from managing the power
> state during suspend and resume.

Please double check this, look like  correct

Frank
>
> --
> Sashiko AI review · https://sashiko.dev/#/patchset/cover.1784059139.git.stefano.r@variscite.com?part=2

Re: [PATCH v2 3/3] arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board

[Frank Li]

On Tue, Jul 14, 2026 at 08:18:04PM +0000, sashiko-bot@kernel.org wrote:
> Thank you for your contribution! Sashiko AI review found 4 potential issue(s) to consider:
> - [Medium] The capacitive touch panel node `ft5x06_ts` lacks a `reset-gpios` (or `wake-gpios`) property, stranding a configured pinctrl pad and potentially causing probing failures.
> - [Medium] The pinctrl for the USB VBUS regulator GPIO is incorrectly assigned to the USB controller node instead of the regulator node.
> - [Low] The PCIe node uses the deprecated `reset-gpio` property instead of `reset-gpios`.
> - [Low] The LED node name `led-hearthbeat` contains a typo.
> --
>
> --- Patch [3]: [PATCH v2 3/3] arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board ---
> commit f84a05986e6ac58f10d1a6e2091672e4f1bf919b
> Author: Stefano Radaelli <stefano.r@variscite.com>
>
> arm64: dts: imx8qm-var-som: Add support for Variscite Symphony board
>
> This commit adds device tree support for the Variscite Symphony carrier board
> with the VAR-SOM-MX8 QuadMax system on module. It configures interfaces
> including SD card, USB, Ethernet, I2C, SPI, RTC, TPM, CAN, and PCIe.
>
> Link: https://variscite.com/carrier-boards/symphony-board/
>
> > diff --git a/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
> > new file mode 100644
> > index 0000000000000..bf66786378301
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8qm-var-som-symphony.dts
> [ ... ]
> > +	gpio-leds {
> > +		compatible = "gpio-leds";
> > +
> > +		led-hearthbeat {
>
> [Severity: Low]
> This isn't a bug, but there is a typo in the node name (hearthbeat instead
> of heartbeat).

small nit, fix it

>
> > +			function = LED_FUNCTION_STATUS;
> > +			color = <LED_COLOR_ID_GREEN>;
> > +			gpios = <&pca9534 0 GPIO_ACTIVE_LOW>;
> > +			linux,default-trigger = "heartbeat";
> > +		};
> > +	};
> [ ... ]
> > +	/* Capacitive touch */
> > +	ft5x06_ts: touchscreen@38 {
> > +		compatible = "edt,edt-ft5406";
> > +		pinctrl-names = "default";
> > +		reg = <0x38>;
> > +		pinctrl-0 = <&pinctrl_captouch>;
> > +		interrupt-parent = <&lsio_gpio0>;
> > +		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> > +		touchscreen-size-x = <800>;
> > +		touchscreen-size-y = <480>;
> > +		touchscreen-inverted-x;
> > +		touchscreen-inverted-y;
> > +		wakeup-source;
> > +	};
>
> [Severity: Medium]
> Is this touchscreen node missing a reset-gpios property?
>
> The pinctrl_captouch group configures LSIO_GPIO0_IO16 for the touch
> controller, but it is not assigned to reset-gpios here.

is it for reset or irq line?

>
> Will the edt-ft5406 driver be able to toggle the reset line without it, or
> could this lead to initialization failures?
>
> [ ... ]
> > +&pciea{
> > +	phys = <&hsio_phy 0 PHY_TYPE_PCIE 0>;
> > +	phy-names = "pcie-phy";
> > +	reset-gpio = <&pca6408 1 GPIO_ACTIVE_LOW>;
>
> [Severity: Low]
> Should this use reset-gpios instead of the deprecated reset-gpio property?

Now put under root port

pcie@0 {
}

Frank
>
> > +	status = "okay";
> > +};
> [ ... ]
> > +&usbotg1 {
> > +	dr_mode = "host";
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_usbotg1>;
> > +	vbus-supply = <&reg_usb_otg1_vbus>;
> > +	srp-disable;
> > +	hnp-disable;
> > +	adp-disable;
> > +	disable-over-current;
> > +	status = "okay";
> > +};
>
> [Severity: Medium]
> Is pinctrl_usbotg1 assigned to the wrong node?
>
> The reg_usb_otg1_vbus regulator uses the GPIO to provide power, but the
> pinctrl to configure the pad is placed here on the usbotg1 controller.
>
> Could this cause the GPIO pad to be incorrectly muxed when the fixed
> regulator framework tries to enable power before the USB driver probes?
>
> --
> Sashiko AI review · https://sashiko.dev/#/patchset/cover.1784059139.git.stefano.r@variscite.com?part=3