* [PATCH 0/2] Support ROHM BD79111 ADC/GPIO
@ 2026-11-18 14:18 Matti Vaittinen
2026-11-18 14:19 ` [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111 Matti Vaittinen
2026-11-18 14:19 ` [PATCH 2/2] iio: adc: rohm-bd79112: " Matti Vaittinen
0 siblings, 2 replies; 4+ messages in thread
From: Matti Vaittinen @ 2026-11-18 14:18 UTC (permalink / raw)
To: Matti Vaittinen, Matti Vaittinen, Matti Vaittinen
Cc: Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Matti Vaittinen,
Marcelo Schmitt, Joshua Crofts, Radu Sabau, Janani Sunil,
Salih Erim, Jishnu Prakash, Antoniu Miclaus, Jakub Szczudlo,
linux-iio, devicetree, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 778 bytes --]
Support ROHM BD79111 ADC/GPIO
The ROHM BD79111 is a 12-bit, 16 channel SAR ADC / GPIO IC. Or, a "Signal
Monitor Hub IC" as data-sheet describes it. The key difference compared
to already supported BD79112 is the reduced number of channels (16,
BD79112 had 32) and halved sampling rate (500 KSPS when BD79112
data-sheet stated 1 MSPS).
Matti Vaittinen (2):
dt-bindings: Support ROHM BD79111
iio: adc: rohm-bd79112: Support ROHM BD79111
.../bindings/iio/adc/rohm,bd79112.yaml | 72 +++++++----
drivers/iio/adc/Kconfig | 9 +-
drivers/iio/adc/rohm-bd79112.c | 113 ++++++++++++++----
3 files changed, 148 insertions(+), 46 deletions(-)
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
--
2.56.1
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111
2026-11-18 14:18 [PATCH 0/2] Support ROHM BD79111 ADC/GPIO Matti Vaittinen
@ 2026-11-18 14:19 ` Matti Vaittinen
2026-11-18 14:34 ` sashiko-bot
2026-11-18 14:19 ` [PATCH 2/2] iio: adc: rohm-bd79112: " Matti Vaittinen
1 sibling, 1 reply; 4+ messages in thread
From: Matti Vaittinen @ 2026-11-18 14:19 UTC (permalink / raw)
To: Matti Vaittinen, Matti Vaittinen, Matti Vaittinen
Cc: Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Matti Vaittinen,
Marcelo Schmitt, Joshua Crofts, Radu Sabau, Janani Sunil,
Salih Erim, Jishnu Prakash, Antoniu Miclaus, Jakub Szczudlo,
linux-iio, devicetree, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 4096 bytes --]
From: Matti Vaittinen <mazziesaccount@gmail.com>
ROHM BD79111 is very similar to the BD79112. Both are ADC/GPIO devices,
where pins can be configured to be either used as GPIO or ADC inputs.
ADCs are 12-bit SAR ADCs and GPIOs support input/output but not being IRQ
sources.
The main difference is amount of channels/GPIOs. The BD79112 has 32 pins
for this use, the BD79111 has 16. Furthermore, the BD79111 data-sheet
promises 0.5 MSPS sample rate with maximum of 10 MHz SPI clock, whereas
the BD79112 data-sheet mentioned 1MSPS rate with maximum of 20 MHz SPI
clock.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
---
Note, I had to change the 'root-level' additionalProperties: false to
unevaluatedProperties: false in order to allow the properties in the new
allOf:
- if:
...
section. It seems to me this is what a few other bindings in IIO do, but
I suppose it makes this "less strict". Well, since I am terrible with
writing bindings, I'd better point this out and ask if it's ok, or if
there are better way(s) to handle this?
---
.../bindings/iio/adc/rohm,bd79112.yaml | 72 +++++++++++++------
1 file changed, 50 insertions(+), 22 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml b/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
index aa8b07c3fac1..4f105124ee6f 100644
--- a/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
@@ -4,18 +4,21 @@
$id: http://devicetree.org/schemas/iio/adc/rohm,bd79112.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: ROHM BD79112 ADC/GPO
+title: ROHM BD79111 and BD79112 ADC/GPIO
maintainers:
- Matti Vaittinen <mazziesaccount@gmail.com>
description: |
- The ROHM BD79112 is a 12-bit, 32-channel, SAR ADC. ADC input pins can be
- also configured as general purpose inputs/outputs. SPI should use MODE 3.
+ The ROHM BD79112 is a 12-bit, 32-channel, SAR ADC. The ROHM BD79111 is
+ a 12-bit, 16-channel, SAR ADC. ADC input pins can be also configured as
+ general purpose inputs/outputs. SPI should use MODE 3.
properties:
compatible:
- const: rohm,bd79112
+ enum:
+ - rohm,bd79111
+ - rohm,bd79112
reg:
maxItems: 1
@@ -37,23 +40,6 @@ properties:
"#size-cells":
const: 0
-patternProperties:
- "^channel@([0-9]|[12][0-9]|3[01])$":
- type: object
- $ref: /schemas/iio/adc/adc.yaml#
- description: Represents ADC channel. Omitted channels' inputs are GPIOs.
-
- properties:
- reg:
- description: AIN pin number
- minimum: 0
- maximum: 31
-
- required:
- - reg
-
- additionalProperties: false
-
required:
- compatible
- reg
@@ -62,7 +48,49 @@ required:
- spi-cpha
- spi-cpol
-additionalProperties: false
+unevaluatedProperties: false
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: rohm,bd79112
+ then:
+ patternProperties:
+ "^channel@([0-9]|[12][0-9]|3[01])$":
+ type: object
+ $ref: /schemas/iio/adc/adc.yaml#
+ description: Represents ADC channel. Omitted channels' inputs are GPIOs.
+
+ properties:
+ reg:
+ description: AIN pin number
+ minimum: 0
+ maximum: 31
+
+ required:
+ - reg
+
+ additionalProperties: false
+ else:
+ # BD79111 has only 16 channels
+ patternProperties:
+ "^channel@([0-9]|1[0-5])$":
+ type: object
+ $ref: /schemas/iio/adc/adc.yaml#
+ description: Represents ADC channel. Omitted channels' inputs are GPIOs.
+
+ properties:
+ reg:
+ description: AIN pin number
+ minimum: 0
+ maximum: 15
+
+ required:
+ - reg
+
+ additionalProperties: false
examples:
- |
--
2.56.1
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 2/2] iio: adc: rohm-bd79112: Support ROHM BD79111
2026-11-18 14:18 [PATCH 0/2] Support ROHM BD79111 ADC/GPIO Matti Vaittinen
2026-11-18 14:19 ` [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111 Matti Vaittinen
@ 2026-11-18 14:19 ` Matti Vaittinen
1 sibling, 0 replies; 4+ messages in thread
From: Matti Vaittinen @ 2026-11-18 14:19 UTC (permalink / raw)
To: Matti Vaittinen, Matti Vaittinen, Matti Vaittinen
Cc: Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Matti Vaittinen,
Marcelo Schmitt, Joshua Crofts, Radu Sabau, Janani Sunil,
Salih Erim, Jishnu Prakash, Antoniu Miclaus, Jakub Szczudlo,
linux-iio, devicetree, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 10163 bytes --]
From: Matti Vaittinen <mazziesaccount@gmail.com>
ROHM BD79111 is very similar to the BD79112. Both are ADC/GPIO devices,
where pins can be configured to be either used as GPIO or ADC inputs.
ADCs are 12-bit SAR ADCs and GPIOs support input/output but not being IRQ
sources.
The main difference is amount of channels/GPIOs. The BD79112 has 32 pins
for this use, the BD79111 has 16. Furthermore, the BD79111 data-sheet
promises 0.5 MSPS sample rate with maximum of 10 MHz SPI clock, whereas
the BD79112 data-sheet mentioned 1MSPS rate with maximum of 20 MHz SPI
clock.
NOTE: In order to achieve those speeds one needs to use more optimized
protocol compared to the one implemented in this driver. This driver
retrieves samples using two 16-bit SPI transactions. The first
transaction writes the channel to be sampled, and ignores data on MISO.
Then the next 16-bit transaction carries the data.
Achieving maximum sample-rate would require the driver to interpret the
MISO data of each 16-bit transaction so, that when the
channel-to-be-sampled was sent in transaction N, the data is read at
transaction N+1 - which also already configures the channel to be
sampled for transaction N+2. Supporting this would require the
channel-to-be-read for the future read to be known when the current
channel data is retrieved. For raw-reads this is not possible and for
buffered reads it would make things a bit hairy.
So, here we aim for simplicity instead of the peak performance.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
---
drivers/iio/adc/Kconfig | 9 +--
drivers/iio/adc/rohm-bd79112.c | 113 +++++++++++++++++++++++++++------
2 files changed, 98 insertions(+), 24 deletions(-)
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index a802d8ee4dd9..db9e0a0713e1 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -1516,14 +1516,15 @@ config RN5T618_ADC
will be called rn5t618-adc.
config ROHM_BD79112
- tristate "Rohm BD79112 ADC driver"
+ tristate "ROHM BD79112 and BD79111 ADC/GPIO driver"
depends on SPI && GPIOLIB
select REGMAP_SPI
select IIO_ADC_HELPER
help
- Say yes here to build support for the ROHM BD79112 ADC. The
- ROHM BD79112 is a 12-bit, 32-channel, SAR ADC. Analog inputs
- can also be used for GPIO.
+ Say yes here to build support for the ROHM BD79112 and BD79111
+ ADCs. Both of the ICs are 12-bit SAR ADCs. The ROHM BD79112 has
+ 32-channels, the BD79111 has 16. Analog inputs can also be used
+ for GPIO.
config ROHM_BD79124
tristate "Rohm BD79124 ADC driver"
diff --git a/drivers/iio/adc/rohm-bd79112.c b/drivers/iio/adc/rohm-bd79112.c
index 2506fec7be84..604c6ccafb4f 100644
--- a/drivers/iio/adc/rohm-bd79112.c
+++ b/drivers/iio/adc/rohm-bd79112.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
- * ROHM ADC driver for BD79112 signal monitoring hub.
+ * ROHM ADC driver for BD79111 and BD79112 signal monitoring hubs.
* Copyright (C) 2025, ROHM Semiconductor.
*
* SPI communication derived from ad7923.c and ti-ads7950.c
@@ -26,7 +26,17 @@
#define BD79112_MAX_NUM_CHANNELS 32
+struct bd79112_data;
+
+struct bd7911x_chip_data {
+ const char *name;
+ const char * const *chan_names;
+ unsigned int num_channels;
+ int (*init_disable_gpios)(struct bd79112_data *data);
+};
+
struct bd79112_data {
+ const struct bd7911x_chip_data *cd;
struct spi_device *spi;
struct regmap *map;
struct device *dev;
@@ -369,7 +379,6 @@ static int bd79112_gpio_output(struct gpio_chip *gc, unsigned int offset,
}
static const struct gpio_chip bd79112_gpio_chip = {
- .label = "bd79112-gpio",
.get_direction = bd79112_gpio_dir_get,
.direction_input = bd79112_gpio_input,
.direction_output = bd79112_gpio_output,
@@ -378,20 +387,20 @@ static const struct gpio_chip bd79112_gpio_chip = {
.set_multiple = bd79112_gpio_set_multiple,
.init_valid_mask = bd79112_gpio_init_valid_mask,
.can_sleep = true,
- .ngpio = 32,
.base = -1,
};
-static unsigned int bd79112_get_gpio_pins(const struct iio_chan_spec *cs, int num_channels)
+static unsigned int bd79112_get_gpio_pins(const struct iio_chan_spec *cs,
+ int num_channels, int max_channels)
{
unsigned int i, gpio_channels;
/*
- * Let's initialize the mux config to say that all 32 channels are
+ * Let's initialize the mux config to say that all channels are
* GPIOs. Then we can just loop through the iio_chan_spec and clear the
* bits for found ADC channels.
*/
- gpio_channels = GENMASK(31, 0);
+ gpio_channels = GENMASK(max_channels - 1, 0);
for (i = 0; i < num_channels; i++)
gpio_channels &= ~BIT(cs[i].channel);
@@ -410,6 +419,61 @@ static const char * const bd79112_chan_names[] = {
"AGIO12B", "AGIO13B", "AGIO14B", "AGIO15B", /* 28 - 31 */
};
+static int bd79112_disable_gpios(struct bd79112_data *data)
+{
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < BD79112_NUM_GPIO_EN_REGS; i++) {
+ ret = regmap_write(data->map, BD79112_FIRST_GPIO_EN_REG + i, 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/* The BD79111 only has the registers for pins 0 - 15 */
+static int bd79111_disable_gpios(struct bd79112_data *data)
+{
+ static const unsigned int regs[] = {
+ BD79112_REG_GPI_EN_A8_A15, BD79112_REG_GPI_EN_A0_A7,
+ BD79112_REG_GPO_EN_A8_A15, BD79112_REG_GPO_EN_A0_A7,
+ };
+ unsigned int i;
+ int ret;
+
+ for (i = 0; i < ARRAY_SIZE(regs); i++) {
+ ret = regmap_write(data->map, regs[i], 0);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/* The BD79111 channel names as in the data-sheet */
+static const char * const bd79111_chan_names[] = {
+ "AGIO0", "AGIO1", "AGIO2", "AGIO3", /* 0 - 3 */
+ "AGIO4", "AGIO5", "AGIO6", "AGIO7", /* 4 - 7 */
+ "AGIO8", "AGIO9", "AGIO10", "AGIO11", /* 8 - 11 */
+ "AGIO12", "AGIO13", "AGIO14", "AGIO15", /* 12 - 15 */
+};
+
+static const struct bd7911x_chip_data bd79111_chip_data = {
+ .name = "bd79111",
+ .chan_names = bd79111_chan_names,
+ .num_channels = 16,
+ .init_disable_gpios = bd79111_disable_gpios,
+};
+
+static const struct bd7911x_chip_data bd79112_chip_data = {
+ .name = "bd79112",
+ .chan_names = bd79112_chan_names,
+ .num_channels = 32,
+ .init_disable_gpios = bd79112_disable_gpios,
+};
+
static int bd79112_probe(struct spi_device *spi)
{
struct bd79112_data *data;
@@ -425,6 +489,10 @@ static int bd79112_probe(struct spi_device *spi)
return -ENOMEM;
data = iio_priv(iio_dev);
+ data->cd = spi_get_device_match_data(spi);
+ if (!data->cd)
+ return -ENODEV;
+
data->spi = spi;
data->dev = dev;
data->map = devm_regmap_init(dev, NULL, data, &bd79112_regmap);
@@ -462,7 +530,7 @@ static int bd79112_probe(struct spi_device *spi)
"Failed to optimize SPI write message\n");
ret = devm_iio_adc_device_alloc_chaninfo_se(dev, &bd79112_chan_template,
- BD79112_MAX_NUM_CHANNELS - 1,
+ data->cd->num_channels - 1,
&cs);
/* Register all pins as GPIOs if there are no ADC channels */
@@ -476,10 +544,10 @@ static int bd79112_probe(struct spi_device *spi)
iio_dev->channels = cs;
for (i = 0; i < iio_dev->num_channels; i++)
- cs[i].datasheet_name = bd79112_chan_names[cs[i].channel];
+ cs[i].datasheet_name = data->cd->chan_names[cs[i].channel];
iio_dev->info = &bd79112_info;
- iio_dev->name = "bd79112";
+ iio_dev->name = data->cd->name;
iio_dev->modes = INDIO_DIRECT_MODE;
/*
@@ -488,12 +556,9 @@ static int bd79112_probe(struct spi_device *spi)
* without having to worry about some pins being initially used for
* GPIO.
*/
- for (i = 0; i < BD79112_NUM_GPIO_EN_REGS; i++) {
- ret = regmap_write(data->map, BD79112_FIRST_GPIO_EN_REG + i, 0);
- if (ret)
- return dev_err_probe(dev, ret,
- "Failed to initialize channels\n");
- }
+ ret = data->cd->init_disable_gpios(data);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to initialize channels\n");
ret = devm_iio_device_register(data->dev, iio_dev);
if (ret)
@@ -501,14 +566,15 @@ static int bd79112_probe(struct spi_device *spi)
register_gpios:
gpio_pins = bd79112_get_gpio_pins(iio_dev->channels,
- iio_dev->num_channels);
+ iio_dev->num_channels,
+ data->cd->num_channels);
/* If all channels are reserved for ADC, then we're done. */
if (!gpio_pins)
return 0;
/* Default all the GPIO pins to GPI */
- for_each_set_bit(pin, &gpio_pins, BD79112_MAX_NUM_CHANNELS) {
+ for_each_set_bit(pin, &gpio_pins, data->cd->num_channels) {
ret = bd79112_gpio_dir_set(data, pin, GPIO_LINE_DIRECTION_IN);
if (ret)
return dev_err_probe(dev, ret,
@@ -518,18 +584,25 @@ static int bd79112_probe(struct spi_device *spi)
data->gpio_valid_mask = gpio_pins;
data->gc = bd79112_gpio_chip;
data->gc.parent = dev;
+ data->gc.ngpio = data->cd->num_channels;
+ data->gc.label = devm_kasprintf(dev, GFP_KERNEL, "%s-gpio",
+ data->cd->name);
+ if (!data->gc.label)
+ return -ENOMEM;
return devm_gpiochip_add_data(dev, &data->gc, data);
}
static const struct of_device_id bd79112_of_match[] = {
- { .compatible = "rohm,bd79112" },
+ { .compatible = "rohm,bd79111", .data = &bd79111_chip_data },
+ { .compatible = "rohm,bd79112", .data = &bd79112_chip_data },
{ }
};
MODULE_DEVICE_TABLE(of, bd79112_of_match);
static const struct spi_device_id bd79112_id[] = {
- { .name = "bd79112" },
+ { .name = "bd79111", .driver_data = (kernel_ulong_t)&bd79111_chip_data },
+ { .name = "bd79112", .driver_data = (kernel_ulong_t)&bd79112_chip_data },
{ }
};
MODULE_DEVICE_TABLE(spi, bd79112_id);
@@ -545,6 +618,6 @@ static struct spi_driver bd79112_driver = {
module_spi_driver(bd79112_driver);
MODULE_AUTHOR("Matti Vaittinen <mazziesaccount@gmail.com>");
-MODULE_DESCRIPTION("Driver for ROHM BD79112 ADC/GPIO");
+MODULE_DESCRIPTION("Driver for ROHM BD79111 and BD79112 ADC/GPIO");
MODULE_LICENSE("GPL");
MODULE_IMPORT_NS("IIO_DRIVER");
--
2.56.1
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111
2026-11-18 14:19 ` [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111 Matti Vaittinen
@ 2026-11-18 14:34 ` sashiko-bot
0 siblings, 0 replies; 4+ messages in thread
From: sashiko-bot @ 2026-11-18 14:34 UTC (permalink / raw)
To: Matti Vaittinen; +Cc: devicetree, robh, conor+dt
Thank you for your contribution! Sashiko AI review found 2 potential
issues to consider:
- [Medium] dt-bindings: iio: adc: decimal instead of hex regex for
channel nodes
- [Low] dt-bindings: iio: adc: duplicate channel patternProperties
inside allOf
--
commit 1d2b4969234a59de95b2a054fda32ad7ef3510e0
Author: Matti Vaittinen <mazziesaccount@gmail.com>
dt-bindings: iio: Support ROHM BD79111
This commit adds device tree binding support for the 16-channel ROHM
BD79111 ADC/GPIO alongside the 32-channel BD79112.
> diff --git a/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml b/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
> index aa8b07c3fac10..4f105124ee6f6 100644
> --- a/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
> +++ b/Documentation/devicetree/bindings/iio/adc/rohm,bd79112.yaml
[ ... ]
> @@ -37,23 +40,6 @@ properties:
> "#size-cells":
> const: 0
>
> -patternProperties:
> - "^channel@([0-9]|[12][0-9]|3[01])$":
> - type: object
> - $ref: /schemas/iio/adc/adc.yaml#
> - description: Represents ADC channel. Omitted channels' inputs are GPIOs.
> -
> - properties:
> - reg:
> - description: AIN pin number
> - minimum: 0
> - maximum: 31
> -
> - required:
> - - reg
> -
> - additionalProperties: false
> -
> required:
> - compatible
> - reg
> @@ -62,7 +48,49 @@ required:
> - spi-cpha
> - spi-cpol
>
> -additionalProperties: false
> +unevaluatedProperties: false
> +
> +allOf:
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: rohm,bd79112
> + then:
> + patternProperties:
> + "^channel@([0-9]|[12][0-9]|3[01])$":
> + type: object
> + $ref: /schemas/iio/adc/adc.yaml#
> + description: Represents ADC channel. Omitted channels' inputs are GPIOs.
> +
> + properties:
> + reg:
> + description: AIN pin number
> + minimum: 0
> + maximum: 31
> +
> + required:
> + - reg
> +
> + additionalProperties: false
> + else:
> + # BD79111 has only 16 channels
> + patternProperties:
> + "^channel@([0-9]|1[0-5])$":
[Severity: Medium]
Should the channel unit-address regexes match hexadecimal rather than
decimal ranges?
Devicetree unit addresses and adc.yaml use lowercase hex without leading
zeros, so "^channel@([0-9]|1[0-5])$" rejects valid nodes channel@a through
channel@f on rohm,bd79111 while accepting out-of-range channel@10 through
channel@15. Likewise, the 32-channel pattern rejects channel@a through
channel@f and channel@1a through channel@1f while accepting channel@20
through channel@31; hex ranges would be "^channel@[0-9a-f]$" and
"^channel@1?[0-9a-f]$".
> + type: object
> + $ref: /schemas/iio/adc/adc.yaml#
> + description: Represents ADC channel. Omitted channels' inputs are GPIOs.
> +
> + properties:
> + reg:
> + description: AIN pin number
> + minimum: 0
> + maximum: 15
> +
> + required:
> + - reg
> +
> + additionalProperties: false
[Severity: Low]
Could patternProperties stay at the top level with the 32-channel
definition, and have the allOf if/then block for rohm,bd79111 only narrow
reg maximum to 15 and disallow the upper 16 channel patterns?
That avoids duplicating the entire channel sub-schema across both branches
and allows keeping additionalProperties: false at the root level, matching
Documentation/devicetree/bindings/writing-schema.rst.
--
Sashiko AI review · https://sashiko.dev/#/patchset/cover.1795009599.git.mazziesaccount@gmail.com?part=1
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2026-11-18 14:34 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-18 14:18 [PATCH 0/2] Support ROHM BD79111 ADC/GPIO Matti Vaittinen
2026-11-18 14:19 ` [PATCH 1/2] dt-bindings: iio: Support ROHM BD79111 Matti Vaittinen
2026-11-18 14:34 ` sashiko-bot
2026-11-18 14:19 ` [PATCH 2/2] iio: adc: rohm-bd79112: " Matti Vaittinen
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox