* Re: [PATCH v3 1/8] clk: sunxi: Add Allwinner A20/A31 GMAC clock unit
From: Chen-Yu Tsai @ 2014-02-04 2:43 UTC (permalink / raw)
To: Maxime Ripard
Cc: Emilio Lopez, Mike Turquette, linux-arm-kernel, linux-sunxi,
devicetree, linux-kernel
In-Reply-To: <20140203193108.GC25625@lukather>
Hi,
On Tue, Feb 4, 2014 at 3:31 AM, Maxime Ripard
<maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> wrote:
> Hi,
>
> On Mon, Feb 03, 2014 at 11:32:19AM +0800, Chen-Yu Tsai wrote:
>> The Allwinner A20/A31 clock module controls the transmit clock source
>> and interface type of the GMAC ethernet controller. Model this as
>> a single clock for GMAC drivers to use.
>>
>> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
>> ---
>> Documentation/devicetree/bindings/clock/sunxi.txt | 26 +++++++
>> drivers/clk/sunxi/clk-sunxi.c | 83 +++++++++++++++++++++++
>> 2 files changed, 109 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index 0cf679b..f43b4c0 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -37,6 +37,7 @@ Required properties:
>> "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31
>> "allwinner,sun4i-mod0-clk" - for the module 0 family of clocks
>> "allwinner,sun7i-a20-out-clk" - for the external output clocks
>> + "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31
>>
>> Required properties for all clocks:
>> - reg : shall be the control register address for the clock.
>> @@ -50,6 +51,9 @@ Required properties for all clocks:
>> If the clock module only has one output, the name shall be the
>> module name.
>>
>> +For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate
>> +dummy clocks at 25 MHz and 125 MHz, respectively. See example.
>> +
>> Clock consumers should specify the desired clocks they use with a
>> "clocks" phandle cell. Consumers that are using a gated clock should
>> provide an additional ID in their clock property. This ID is the
>> @@ -96,3 +100,25 @@ mmc0_clk: clk@01c20088 {
>> clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
>> clock-output-names = "mmc0";
>> };
>> +
>> +mii_phy_tx_clk: clk@2 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <25000000>;
>> + clock-output-names = "mii_phy_tx";
>> +};
>> +
>> +gmac_int_tx_clk: clk@3 {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <125000000>;
>> + clock-output-names = "gmac_int_tx";
>> +};
>> +
>> +gmac_clk: clk@01c20164 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun7i-a20-gmac-clk";
>> + reg = <0x01c20164 0x4>;
>> + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
>
> You should also document in which order you expect the parents to
> be. Or it will probably be easier to just use clock-names here.
Is it not clear from the "Required properties" section above?
>
>> + clock-output-names = "gmac";
>> +};
>> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
>> index 736fb60..0b361d2 100644
>> --- a/drivers/clk/sunxi/clk-sunxi.c
>> +++ b/drivers/clk/sunxi/clk-sunxi.c
>> @@ -379,6 +379,89 @@ static void sun7i_a20_get_out_factors(u32 *freq, u32 parent_rate,
>>
>>
>> /**
>> + * sun7i_a20_gmac_clk_setup - Setup function for A20/A31 GMAC clock module
>> + *
>> + * This clock looks something like this
>> + * ________________________
>> + * MII TX clock from PHY >-----|___________ _________|----> to GMAC core
>> + * GMAC Int. RGMII TX clk >----|___________\__/__gate---|----> to PHY
>> + * Ext. 125MHz RGMII TX clk >--|__divider__/ |
>> + * |________________________|
>> + *
>> + * The external 125 MHz reference is optional, i.e. GMAC can use its
>> + * internal TX clock just fine. The A31 GMAC clock module does not have
>> + * the divider controls for the external reference.
>> + *
>> + * To keep it simple, let the GMAC use either the MII TX clock for MII mode,
>> + * and its internal TX clock for GMII and RGMII modes. The GMAC driver should
>> + * select the appropriate source and gate/ungate the output to the PHY.
>> + *
>> + * Only the GMAC should use this clock. Altering the clock so that it doesn't
>> + * match the GMAC's operation parameters will result in the GMAC not being
>> + * able to send traffic out. The GMAC driver should set the clock rate and
>> + * enable/disable this clock to configure the required state. The clock
>> + * driver then responds by auto-reparenting the clock.
>> + */
>> +
>> +#define SUN7I_A20_GMAC_GPIT 2
>> +#define SUN7I_A20_GMAC_MASK 0x3
>> +#define SUN7I_A20_GMAC_MAX_PARENTS 2
>> +
>> +static void __init sun7i_a20_gmac_clk_setup(struct device_node *node)
>> +{
>> + struct clk *clk;
>> + struct clk_mux *mux;
>> + struct clk_gate *gate;
>> + const char *clk_name = node->name;
>> + const char *parents[SUN7I_A20_GMAC_MAX_PARENTS];
>> + void *reg;
>> + int i = 0;
>> +
>> + /* allocate mux and gate clock structs */
>> + mux = kzalloc(sizeof(struct clk_mux), GFP_KERNEL);
>> + if (!mux)
>> + return;
>
> Newline.
>
>> + gate = kzalloc(sizeof(struct clk_gate), GFP_KERNEL);
>> + if (!gate) {
>> + kfree(mux);
>> + return;
>> + }
>> +
>> + reg = of_iomap(node, 0);
>
> You should check for the return code here.
>
>> + of_property_read_string(node, "clock-output-names", &clk_name);
>
> And here too, since you made the clock-output-names property mandatory
>
>> + while (i < SUN7I_A20_GMAC_MAX_PARENTS &&
>> + (parents[i] = of_clk_get_parent_name(node, i)) != NULL)
>
> You should check for an error here too, but if you switch to using
> clock-names, that will probably be refactored anyway.
>
>> + i++;
>> +
>> + /* set up gate and fixed rate properties */
>> + gate->reg = reg;
>> + gate->bit_idx = SUN7I_A20_GMAC_GPIT;
>> + gate->lock = &clk_lock;
>> + mux->reg = reg;
>> + mux->mask = SUN7I_A20_GMAC_MASK;
>> + mux->flags = CLK_MUX_INDEX_BIT;
>> + mux->lock = &clk_lock;
>> +
>> + clk = clk_register_composite(NULL, clk_name,
>> + parents, i,
>> + &mux->hw, &clk_mux_ops,
>> + NULL, NULL,
>> + &gate->hw, &clk_gate_ops,
>> + 0);
>> +
>> + if (!IS_ERR(clk)) {
>> + of_clk_add_provider(node, of_clk_src_simple_get, clk);
>> + clk_register_clkdev(clk, clk_name, NULL);
>> + }
>> +}
>> +CLK_OF_DECLARE(sun7i_a20_gmac, "allwinner,sun7i-a20-gmac-clk",
>> + sun7i_a20_gmac_clk_setup);
>> +
>> +
>> +
>> +/**
>> * sunxi_factors_clk_setup() - Setup function for factor clocks
>> */
>>
>> --
>> 1.9.rc1
>>
>
> It looks fine otherwise.
I'll fix the rest.
Cheers
ChenYu
^ permalink raw reply
* Re: [PATCH v3 3/5] spi: sunxi: Add Allwinner A31 SPI controller driver
From: Mark Brown @ 2014-02-04 0:21 UTC (permalink / raw)
To: Maxime Ripard
Cc: Mike Turquette, Emilio Lopez, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-spi-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
kevin.z.m.zh-Re5JQEeQqe8AvxtiuMwx3w,
sunny-0TFLnhJekD6UEPyfVivIlAC/G2K4zDHf,
shuge-0TFLnhJekD6UEPyfVivIlAC/G2K4zDHf,
zhuzhenhua-0TFLnhJekD6UEPyfVivIlAC/G2K4zDHf
In-Reply-To: <20140131224704.GI2950@lukather>
[-- Attachment #1: Type: text/plain, Size: 1403 bytes --]
On Fri, Jan 31, 2014 at 11:47:04PM +0100, Maxime Ripard wrote:
> On Fri, Jan 31, 2014 at 12:48:09PM +0000, Mark Brown wrote:
> > On Fri, Jan 31, 2014 at 11:55:50AM +0100, Maxime Ripard wrote:
> > > + pm_runtime_enable(&pdev->dev);
> > > + if (!pm_runtime_enabled(&pdev->dev)) {
> > > + ret = sun6i_spi_runtime_resume(&pdev->dev);
> > > + if (ret) {
> > > + dev_err(&pdev->dev, "Couldn't resume the device\n");
> > > + return ret;
> > > + }
> > > + }
> > No, as discussed don't do this - notice how other drivers aren't written
> > this way either. Like I said leave the device powered on startup and
> > then let it be idled by runtime PM.
> Well, some SPI drivers are actually written like that (all the tegra
It's not been done consistently, no - that should be fixed.
> SPI drivers for example). It's not an excuse, but waking up the device
> only to put it back in suspend right away seems kind of
It isn't awesome, no. Ideally the runtime PM code would do this but
then you couldn't ifdef the operations which as far as I can tell is the
main thing people want from disabling it and it gets complicated for
devices that genuinely do power up on startup so here we are.
> inefficient. Plus, the pm_runtime_idle callback you suggested are
> actually calling runtime_idle, while we want to call runtime_suspend.
Yeah, I didn't actually check if I was looking at the right call there.
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply
* Re: [PATCH] arm64: Add architecture support for PCI
From: Jason Gunthorpe @ 2014-02-03 23:31 UTC (permalink / raw)
To: Rob Herring
Cc: Arnd Bergmann, devicetree@vger.kernel.org,
linaro-kernel@lists.linaro.org, linux-pci, Liviu Dudau, LKML,
Catalin Marinas, Bjorn Helgaas, LAKML
In-Reply-To: <CAL_JsqL+3S8w=_Fb-t0rVcq0sDiPSDM6nqn3mR2DHKw=VTffsg@mail.gmail.com>
On Mon, Feb 03, 2014 at 05:07:48PM -0600, Rob Herring wrote:
> > An interesting question however is what the transition plan is to
> > have the code shared between arm32 and arm64: We will certainly need
> > to share at least the dw-pcie and the generic SBSA compliant pci
> > implementation.
>
> You might want to re-read the SBSA. Unless ARM provides an IP block or
> there is some other standard such as EHCI or AHCI, there is no generic
> implementation. You only have to go look at the Linux EHCI or AHCI
> drivers and see how meaningless and inadequate "use EHCI" is. For PCI,
> the text is so brief in the SBSA there will be no way PCI is going to
> just work given all the variations of root complexes, bridges, address
> windows, etc. we typically see on ARM platforms. I could be wrong and
> some AML magic will solve all the problems. :)
The biggest hinderance I've seen while looking at ARM PCI drivers is
quite simply - they don't follow the PCI-E spec. There is a spec, and
it is not followed.
This fixup in the X-Gene is a solid example, the purpose of the BAR in
a PCI-PCI bridge is very clear: using it to specify the system
DRAM aperature is completely wrong.
Not having working aperture windows in the root complex's bridges is
completely wrong.
Lacking any ability to generate 8 and 16 bit config write TLP's is
wrong.
Starting with an end-port PCI-E core and re-tasking it to be a root
port bridge and ignoring all the requirements with the bridge's config
space is utterly and completely WRONG.
Specifying 'use EHCI, AHCI, etc' - which are all PCI based standards
without clearly specifying exactly how PCI is suppose to work is
completely bonkers.
What is needed is a spec that says:
1) Here is how you generate config TLPs. A MMIO region that
conforms to the already specified x86 ECAM would
be perfect
2) Here is a dword by dword break down of the entire config space in
a SOC. Here is where a on-board AHCI controller must show up in
config space. Here is how an external PCI-E port must show
up. Etc. Most of this is already specified, but it clearly needs
to be layed out explicitly for ARM SOCs to actually follow it.
3) Here is how you specify the aperture(s) associated with PCI BAR's
and bridge windows in config space. And yes: The CONFIG SPACE
BARS MUST WORK.
4) Here is how MSI works, these are the values you put in the
address/data and here is how you collect the interrupt.
5) Here is how Legacy INTx must be mapped into the GIC.
This is what x86 does, and they have been doing it well for 10
years. If you want to play in the server game you have to properly
implement PCI.
Jason
^ permalink raw reply
* [PATCH] of: restructure for_each macros to fix compile warnings
From: Rob Herring @ 2014-02-03 23:17 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Geert Uytterhoeven, Grant Likely, Rob Herring, David Howells
From: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Commit 00b2c76a6a "include/linux/of.h: make for_each_child_of_node()
reference its args when CONFIG_OF=n" fixed warnings for unused
variables, but introduced variable "used uninitialized" warnings.
Simply initializing the variables would result in "set but not used"
warnings with W=1.
Fix both types of warnings by making all the for_each macros
unconditional and rely on the dummy static inline functions to
initialize and reference any variables.
Reported-by: Geert Uytterhoeven <geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
Cc: David Howells <dhowells-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
include/linux/of.h | 153 +++++++++++++++++++++++++++++------------------------
1 file changed, 84 insertions(+), 69 deletions(-)
diff --git a/include/linux/of.h b/include/linux/of.h
index 70c64ba..435cb99 100644
--- a/include/linux/of.h
+++ b/include/linux/of.h
@@ -169,35 +169,15 @@ static inline const char *of_node_full_name(const struct device_node *np)
extern struct device_node *of_find_node_by_name(struct device_node *from,
const char *name);
-#define for_each_node_by_name(dn, name) \
- for (dn = of_find_node_by_name(NULL, name); dn; \
- dn = of_find_node_by_name(dn, name))
extern struct device_node *of_find_node_by_type(struct device_node *from,
const char *type);
-#define for_each_node_by_type(dn, type) \
- for (dn = of_find_node_by_type(NULL, type); dn; \
- dn = of_find_node_by_type(dn, type))
extern struct device_node *of_find_compatible_node(struct device_node *from,
const char *type, const char *compat);
-#define for_each_compatible_node(dn, type, compatible) \
- for (dn = of_find_compatible_node(NULL, type, compatible); dn; \
- dn = of_find_compatible_node(dn, type, compatible))
extern struct device_node *of_find_matching_node_and_match(
struct device_node *from,
const struct of_device_id *matches,
const struct of_device_id **match);
-static inline struct device_node *of_find_matching_node(
- struct device_node *from,
- const struct of_device_id *matches)
-{
- return of_find_matching_node_and_match(from, matches, NULL);
-}
-#define for_each_matching_node(dn, matches) \
- for (dn = of_find_matching_node(NULL, matches); dn; \
- dn = of_find_matching_node(dn, matches))
-#define for_each_matching_node_and_match(dn, matches, match) \
- for (dn = of_find_matching_node_and_match(NULL, matches, match); \
- dn; dn = of_find_matching_node_and_match(dn, matches, match))
+
extern struct device_node *of_find_node_by_path(const char *path);
extern struct device_node *of_find_node_by_phandle(phandle handle);
extern struct device_node *of_get_parent(const struct device_node *node);
@@ -209,43 +189,11 @@ extern struct device_node *of_get_next_available_child(
extern struct device_node *of_get_child_by_name(const struct device_node *node,
const char *name);
-#define for_each_child_of_node(parent, child) \
- for (child = of_get_next_child(parent, NULL); child != NULL; \
- child = of_get_next_child(parent, child))
-
-#define for_each_available_child_of_node(parent, child) \
- for (child = of_get_next_available_child(parent, NULL); child != NULL; \
- child = of_get_next_available_child(parent, child))
-
-static inline int of_get_child_count(const struct device_node *np)
-{
- struct device_node *child;
- int num = 0;
-
- for_each_child_of_node(np, child)
- num++;
-
- return num;
-}
-
-static inline int of_get_available_child_count(const struct device_node *np)
-{
- struct device_node *child;
- int num = 0;
-
- for_each_available_child_of_node(np, child)
- num++;
-
- return num;
-}
/* cache lookup */
extern struct device_node *of_find_next_cache_node(const struct device_node *);
extern struct device_node *of_find_node_with_property(
struct device_node *from, const char *prop_name);
-#define for_each_node_with_property(dn, prop_name) \
- for (dn = of_find_node_with_property(NULL, prop_name); dn; \
- dn = of_find_node_with_property(dn, prop_name))
extern struct property *of_find_property(const struct device_node *np,
const char *name,
@@ -367,42 +315,53 @@ static inline struct device_node *of_find_node_by_name(struct device_node *from,
return NULL;
}
-static inline struct device_node *of_get_parent(const struct device_node *node)
+static inline struct device_node *of_find_node_by_type(struct device_node *from,
+ const char *type)
{
return NULL;
}
-static inline bool of_have_populated_dt(void)
+static inline struct device_node *of_find_matching_node_and_match(
+ struct device_node *from,
+ const struct of_device_id *matches,
+ const struct of_device_id **match)
{
- return false;
+ return NULL;
}
-/* Kill an unused variable warning on a device_node pointer */
-static inline void __of_use_dn(const struct device_node *np)
+static inline struct device_node *of_get_parent(const struct device_node *node)
{
+ return NULL;
}
-#define for_each_child_of_node(parent, child) \
- while (__of_use_dn(parent), __of_use_dn(child), 0)
+static inline struct device_node *of_get_next_child(
+ const struct device_node *node, struct device_node *prev)
+{
+ return NULL;
+}
-#define for_each_available_child_of_node(parent, child) \
- while (0)
+static inline struct device_node *of_get_next_available_child(
+ const struct device_node *node, struct device_node *prev)
+{
+ return NULL;
+}
-static inline struct device_node *of_get_child_by_name(
- const struct device_node *node,
- const char *name)
+static inline struct device_node *of_find_node_with_property(
+ struct device_node *from, const char *prop_name)
{
return NULL;
}
-static inline int of_get_child_count(const struct device_node *np)
+static inline bool of_have_populated_dt(void)
{
- return 0;
+ return false;
}
-static inline int of_get_available_child_count(const struct device_node *np)
+static inline struct device_node *of_get_child_by_name(
+ const struct device_node *node,
+ const char *name)
{
- return 0;
+ return NULL;
}
static inline int of_device_is_compatible(const struct device_node *device,
@@ -569,6 +528,13 @@ extern int of_node_to_nid(struct device_node *np);
static inline int of_node_to_nid(struct device_node *device) { return 0; }
#endif
+static inline struct device_node *of_find_matching_node(
+ struct device_node *from,
+ const struct of_device_id *matches)
+{
+ return of_find_matching_node_and_match(from, matches, NULL);
+}
+
/**
* of_property_read_bool - Findfrom a property
* @np: device node from which the property value is to be read.
@@ -618,6 +584,55 @@ static inline int of_property_read_u32(const struct device_node *np,
s; \
s = of_prop_next_string(prop, s))
+#define for_each_node_by_name(dn, name) \
+ for (dn = of_find_node_by_name(NULL, name); dn; \
+ dn = of_find_node_by_name(dn, name))
+#define for_each_node_by_type(dn, type) \
+ for (dn = of_find_node_by_type(NULL, type); dn; \
+ dn = of_find_node_by_type(dn, type))
+#define for_each_compatible_node(dn, type, compatible) \
+ for (dn = of_find_compatible_node(NULL, type, compatible); dn; \
+ dn = of_find_compatible_node(dn, type, compatible))
+#define for_each_matching_node(dn, matches) \
+ for (dn = of_find_matching_node(NULL, matches); dn; \
+ dn = of_find_matching_node(dn, matches))
+#define for_each_matching_node_and_match(dn, matches, match) \
+ for (dn = of_find_matching_node_and_match(NULL, matches, match); \
+ dn; dn = of_find_matching_node_and_match(dn, matches, match))
+
+#define for_each_child_of_node(parent, child) \
+ for (child = of_get_next_child(parent, NULL); child != NULL; \
+ child = of_get_next_child(parent, child))
+#define for_each_available_child_of_node(parent, child) \
+ for (child = of_get_next_available_child(parent, NULL); child != NULL; \
+ child = of_get_next_available_child(parent, child))
+
+#define for_each_node_with_property(dn, prop_name) \
+ for (dn = of_find_node_with_property(NULL, prop_name); dn; \
+ dn = of_find_node_with_property(dn, prop_name))
+
+static inline int of_get_child_count(const struct device_node *np)
+{
+ struct device_node *child;
+ int num = 0;
+
+ for_each_child_of_node(np, child)
+ num++;
+
+ return num;
+}
+
+static inline int of_get_available_child_count(const struct device_node *np)
+{
+ struct device_node *child;
+ int num = 0;
+
+ for_each_available_child_of_node(np, child)
+ num++;
+
+ return num;
+}
+
#if defined(CONFIG_PROC_FS) && defined(CONFIG_PROC_DEVICETREE)
extern void proc_device_tree_add_node(struct device_node *, struct proc_dir_entry *);
extern void proc_device_tree_add_prop(struct proc_dir_entry *pde, struct property *prop);
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH] arm64: Add architecture support for PCI
From: Rob Herring @ 2014-02-03 23:07 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linaro-kernel@lists.linaro.org, devicetree@vger.kernel.org,
Catalin Marinas, Liviu Dudau, LKML, linux-pci, Bjorn Helgaas,
LAKML
In-Reply-To: <3808209.DeG1VobanZ@wuerfel>
On Mon, Feb 3, 2014 at 2:05 PM, Arnd Bergmann <arnd@arndb.de> wrote:
> On Monday 03 February 2014 19:18:38 Liviu Dudau wrote:
>> On Mon, Feb 03, 2014 at 06:58:56PM +0000, Arnd Bergmann wrote:
>> > On Monday 03 February 2014 18:43:48 Liviu Dudau wrote:
[snip]
>> Agree. This is the RFC version. I didn't dare to post a patch with fixes
>> for all architectures. :)
>
> No need to change the other architectures. You can make it opt-in for
> now and just put the code into a common location.
>
> An interesting question however is what the transition plan is to
> have the code shared between arm32 and arm64: We will certainly need
> to share at least the dw-pcie and the generic SBSA compliant pci
> implementation.
You might want to re-read the SBSA. Unless ARM provides an IP block or
there is some other standard such as EHCI or AHCI, there is no generic
implementation. You only have to go look at the Linux EHCI or AHCI
drivers and see how meaningless and inadequate "use EHCI" is. For PCI,
the text is so brief in the SBSA there will be no way PCI is going to
just work given all the variations of root complexes, bridges, address
windows, etc. we typically see on ARM platforms. I could be wrong and
some AML magic will solve all the problems. :)
Rob
^ permalink raw reply
* [PATCH v5 5/6] spmi: document the PMIC arbiter SPMI bindings
From: Josh Cartwright @ 2014-02-03 23:05 UTC (permalink / raw)
To: Greg Kroah-Hartman, linux-kernel
Cc: Mark Rutland, devicetree, Pawel Moll, Ian Campbell, linux-arm-msm,
Gilad Avidov, linux-doc, Rob Herring, Michael Bohan, Rob Landley,
Kumar Gala, Sagar Dharia, linux-arm-kernel
In-Reply-To: <1391468739-20987-1-git-send-email-joshc@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
---
.../bindings/spmi/qcom,spmi-pmic-arb.txt | 60 ++++++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
diff --git a/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
new file mode 100644
index 0000000..a0a5759
--- /dev/null
+++ b/Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
@@ -0,0 +1,60 @@
+Qualcomm SPMI Controller (PMIC Arbiter)
+
+The SPMI PMIC Arbiter is found on the Snapdragon 800 Series. It is an SPMI
+controller with wrapping arbitration logic to allow for multiple on-chip
+devices to control a single SPMI master.
+
+The PMIC Arbiter can also act as an interrupt controller, providing interrupts
+to slave devices.
+
+See spmi.txt for the generic SPMI controller binding requirements for child
+nodes.
+
+See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
+generic interrupt controller binding documentation.
+
+Required properties:
+- compatible : should be "qcom,spmi-pmic-arb".
+- reg-names : should be "core", "intr", "cnfg"
+- reg : register specifiers, must contain:
+ "core" - core registers
+ "intr" - interrupt controller registers
+ "cnfg" - configuration registers
+- #address-cells : must be set to 2
+- #size-cells : must be set to 0
+- qcom,ee : indicates the active Execution Environment identifier (0-5)
+- qcom,channel : which of the PMIC Arb provided channels to use for accesses (0-5)
+- interrupts : interrupt list for the PMIC Arb controller, must contain a
+ single interrupt entry for the peripheral interrupt
+- interrupt-names : corresponding interrupt names for the interrupts
+ listed in the 'interrupts' property, must contain:
+ "periph_irq" - summary interrupt for PMIC peripherals
+- interrupt-controller : boolean indicator that the PMIC arbiter is an interrupt controller
+- #interrupt-cells : must be set to 4. Interrupts are specified as a 4-tuple:
+ cell 1: slave ID for the requested interrupt (0-15)
+ cell 2: peripheral ID for requested interrupt (0-255)
+ cell 3: the requested peripheral interrupt (0-7)
+ cell 4: interrupt flags indicating level-sense information, as defined in
+ dt-bindings/interrupt-controller/irq.h
+
+Example:
+
+ spmi {
+ compatible = "qcom,spmi-pmic-arb";
+ reg-names = "core", "intr", "cnfg";
+ reg = <0xfc4cf000 0x1000>,
+ <0xfc4cb000 0x1000>,
+ <0xfc4ca000 0x1000>;
+
+ interrupt-names = "periph_irq";
+ interrupts = <0 190 0>;
+
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 3/6] spmi: Add MSM PMIC Arbiter SPMI controller
From: Josh Cartwright @ 2014-02-03 23:05 UTC (permalink / raw)
To: Greg Kroah-Hartman, Grant Likely, Rob Herring
Cc: linux-arm-kernel, linux-arm-msm, Sagar Dharia, Gilad Avidov,
Michael Bohan, Kenneth Heitke, linux-kernel, devicetree
In-Reply-To: <1391468739-20987-1-git-send-email-joshc@codeaurora.org>
From: Kenneth Heitke <kheitke@codeaurora.org>
Qualcomm's PMIC Arbiter SPMI controller functions as a bus master and
is used to communication with one or more PMIC (slave) devices on the
SPMI bus. The PMIC Arbiter is actually a hardware wrapper around the
SPMI controller that provides concurrent and autonomous PMIC access
to various entities that need to communicate with the PMIC.
The SPMI controller hardware handles all of the SPMI bus activity (bus
arbitration, sequence start condition, transmission of frames, etc).
This software driver uses the PMIC Arbiter register interface to
initiate command sequences on the SPMI bus. The status register is
read to determine when the command sequence has completed and whether
or not it completed successfully.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
---
drivers/spmi/Kconfig | 17 ++
drivers/spmi/Makefile | 2 +
drivers/spmi/spmi-pmic-arb.c | 405 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 424 insertions(+)
create mode 100644 drivers/spmi/spmi-pmic-arb.c
diff --git a/drivers/spmi/Kconfig b/drivers/spmi/Kconfig
index 1dbfee0..80b7901 100644
--- a/drivers/spmi/Kconfig
+++ b/drivers/spmi/Kconfig
@@ -7,3 +7,20 @@ menuconfig SPMI
SPMI (System Power Management Interface) is a two-wire
serial interface between baseband and application processors
and Power Management Integrated Circuits (PMIC).
+
+if SPMI
+
+config SPMI_MSM_PMIC_ARB
+ tristate "Qualcomm MSM SPMI Controller (PMIC Arbiter)"
+ depends on ARM
+ depends on ARCH_MSM || COMPILE_TEST
+ default ARCH_MSM
+ help
+ If you say yes to this option, support will be included for the
+ built-in SPMI PMIC Arbiter interface on Qualcomm MSM family
+ processors.
+
+ This is required for communicating with Qualcomm PMICs and
+ other devices that have the SPMI interface.
+
+endif
diff --git a/drivers/spmi/Makefile b/drivers/spmi/Makefile
index 1de1acd..fc75104 100644
--- a/drivers/spmi/Makefile
+++ b/drivers/spmi/Makefile
@@ -2,3 +2,5 @@
# Makefile for kernel SPMI framework.
#
obj-$(CONFIG_SPMI) += spmi.o
+
+obj-$(CONFIG_SPMI_MSM_PMIC_ARB) += spmi-pmic-arb.o
diff --git a/drivers/spmi/spmi-pmic-arb.c b/drivers/spmi/spmi-pmic-arb.c
new file mode 100644
index 0000000..b7f753f
--- /dev/null
+++ b/drivers/spmi/spmi-pmic-arb.c
@@ -0,0 +1,405 @@
+/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/spmi.h>
+
+/* PMIC Arbiter configuration registers */
+#define PMIC_ARB_VERSION 0x0000
+#define PMIC_ARB_INT_EN 0x0004
+
+/* PMIC Arbiter channel registers */
+#define PMIC_ARB_CMD(N) (0x0800 + (0x80 * (N)))
+#define PMIC_ARB_CONFIG(N) (0x0804 + (0x80 * (N)))
+#define PMIC_ARB_STATUS(N) (0x0808 + (0x80 * (N)))
+#define PMIC_ARB_WDATA0(N) (0x0810 + (0x80 * (N)))
+#define PMIC_ARB_WDATA1(N) (0x0814 + (0x80 * (N)))
+#define PMIC_ARB_RDATA0(N) (0x0818 + (0x80 * (N)))
+#define PMIC_ARB_RDATA1(N) (0x081C + (0x80 * (N)))
+
+/* Interrupt Controller */
+#define SPMI_PIC_OWNER_ACC_STATUS(M, N) (0x0000 + ((32 * (M)) + (4 * (N))))
+#define SPMI_PIC_ACC_ENABLE(N) (0x0200 + (4 * (N)))
+#define SPMI_PIC_IRQ_STATUS(N) (0x0600 + (4 * (N)))
+#define SPMI_PIC_IRQ_CLEAR(N) (0x0A00 + (4 * (N)))
+
+/* Mapping Table */
+#define SPMI_MAPPING_TABLE_REG(N) (0x0B00 + (4 * (N)))
+#define SPMI_MAPPING_BIT_INDEX(X) (((X) >> 18) & 0xF)
+#define SPMI_MAPPING_BIT_IS_0_FLAG(X) (((X) >> 17) & 0x1)
+#define SPMI_MAPPING_BIT_IS_0_RESULT(X) (((X) >> 9) & 0xFF)
+#define SPMI_MAPPING_BIT_IS_1_FLAG(X) (((X) >> 8) & 0x1)
+#define SPMI_MAPPING_BIT_IS_1_RESULT(X) (((X) >> 0) & 0xFF)
+
+#define SPMI_MAPPING_TABLE_LEN 255
+#define SPMI_MAPPING_TABLE_TREE_DEPTH 16 /* Maximum of 16-bits */
+
+/* Ownership Table */
+#define SPMI_OWNERSHIP_TABLE_REG(N) (0x0700 + (4 * (N)))
+#define SPMI_OWNERSHIP_PERIPH2OWNER(X) ((X) & 0x7)
+
+/* Channel Status fields */
+enum pmic_arb_chnl_status {
+ PMIC_ARB_STATUS_DONE = (1 << 0),
+ PMIC_ARB_STATUS_FAILURE = (1 << 1),
+ PMIC_ARB_STATUS_DENIED = (1 << 2),
+ PMIC_ARB_STATUS_DROPPED = (1 << 3),
+};
+
+/* Command register fields */
+#define PMIC_ARB_CMD_MAX_BYTE_COUNT 8
+
+/* Command Opcodes */
+enum pmic_arb_cmd_op_code {
+ PMIC_ARB_OP_EXT_WRITEL = 0,
+ PMIC_ARB_OP_EXT_READL = 1,
+ PMIC_ARB_OP_EXT_WRITE = 2,
+ PMIC_ARB_OP_RESET = 3,
+ PMIC_ARB_OP_SLEEP = 4,
+ PMIC_ARB_OP_SHUTDOWN = 5,
+ PMIC_ARB_OP_WAKEUP = 6,
+ PMIC_ARB_OP_AUTHENTICATE = 7,
+ PMIC_ARB_OP_MSTR_READ = 8,
+ PMIC_ARB_OP_MSTR_WRITE = 9,
+ PMIC_ARB_OP_EXT_READ = 13,
+ PMIC_ARB_OP_WRITE = 14,
+ PMIC_ARB_OP_READ = 15,
+ PMIC_ARB_OP_ZERO_WRITE = 16,
+};
+
+/* Maximum number of support PMIC peripherals */
+#define PMIC_ARB_MAX_PERIPHS 256
+#define PMIC_ARB_PERIPH_ID_VALID (1 << 15)
+#define PMIC_ARB_TIMEOUT_US 100
+#define PMIC_ARB_MAX_TRANS_BYTES (8)
+
+#define PMIC_ARB_APID_MASK 0xFF
+#define PMIC_ARB_PPID_MASK 0xFFF
+
+/* interrupt enable bit */
+#define SPMI_PIC_ACC_ENABLE_BIT BIT(0)
+
+/**
+ * spmi_pmic_arb_dev - SPMI PMIC Arbiter object
+ *
+ * @base: address of the PMIC Arbiter core registers.
+ * @intr: address of the SPMI interrupt control registers.
+ * @cnfg: address of the PMIC Arbiter configuration registers.
+ * @lock: lock to synchronize accesses.
+ * @channel: which channel to use for accesses.
+ */
+struct spmi_pmic_arb_dev {
+ void __iomem *base;
+ void __iomem *intr;
+ void __iomem *cnfg;
+ spinlock_t lock;
+ u8 channel;
+};
+
+static inline u32 pmic_arb_base_read(struct spmi_pmic_arb_dev *dev, u32 offset)
+{
+ return readl_relaxed(dev->base + offset);
+}
+
+static inline void pmic_arb_base_write(struct spmi_pmic_arb_dev *dev,
+ u32 offset, u32 val)
+{
+ writel_relaxed(val, dev->base + offset);
+}
+
+/**
+ * pa_read_data: reads pmic-arb's register and copy 1..4 bytes to buf
+ * @bc: byte count -1. range: 0..3
+ * @reg: register's address
+ * @buf: output parameter, length must be bc + 1
+ */
+static void pa_read_data(struct spmi_pmic_arb_dev *dev, u8 *buf, u32 reg, u8 bc)
+{
+ u32 data = pmic_arb_base_read(dev, reg);
+ memcpy(buf, &data, (bc & 3) + 1);
+}
+
+/**
+ * pa_write_data: write 1..4 bytes from buf to pmic-arb's register
+ * @bc: byte-count -1. range: 0..3.
+ * @reg: register's address.
+ * @buf: buffer to write. length must be bc + 1.
+ */
+static void
+pa_write_data(struct spmi_pmic_arb_dev *dev, const u8 *buf, u32 reg, u8 bc)
+{
+ u32 data = 0;
+ memcpy(&data, buf, (bc & 3) + 1);
+ pmic_arb_base_write(dev, reg, data);
+}
+
+static int pmic_arb_wait_for_done(struct spmi_controller *ctrl)
+{
+ struct spmi_pmic_arb_dev *dev = spmi_controller_get_drvdata(ctrl);
+ u32 status = 0;
+ u32 timeout = PMIC_ARB_TIMEOUT_US;
+ u32 offset = PMIC_ARB_STATUS(dev->channel);
+
+ while (timeout--) {
+ status = pmic_arb_base_read(dev, offset);
+
+ if (status & PMIC_ARB_STATUS_DONE) {
+ if (status & PMIC_ARB_STATUS_DENIED) {
+ dev_err(&ctrl->dev,
+ "%s: transaction denied (0x%x)\n",
+ __func__, status);
+ return -EPERM;
+ }
+
+ if (status & PMIC_ARB_STATUS_FAILURE) {
+ dev_err(&ctrl->dev,
+ "%s: transaction failed (0x%x)\n",
+ __func__, status);
+ return -EIO;
+ }
+
+ if (status & PMIC_ARB_STATUS_DROPPED) {
+ dev_err(&ctrl->dev,
+ "%s: transaction dropped (0x%x)\n",
+ __func__, status);
+ return -EIO;
+ }
+
+ return 0;
+ }
+ udelay(1);
+ }
+
+ dev_err(&ctrl->dev,
+ "%s: timeout, status 0x%x\n",
+ __func__, status);
+ return -ETIMEDOUT;
+}
+
+/* Non-data command */
+static int pmic_arb_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u32 cmd;
+ int rc;
+
+ /* Check for valid non-data command */
+ if (opc < SPMI_CMD_RESET || opc > SPMI_CMD_WAKEUP)
+ return -EINVAL;
+
+ cmd = ((opc | 0x40) << 27) | ((sid & 0xf) << 20);
+
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+
+ return rc;
+}
+
+static int pmic_arb_read_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
+ u16 addr, u8 *buf, size_t len)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u8 bc = len - 1;
+ u32 cmd;
+ int rc;
+
+ if (bc >= PMIC_ARB_MAX_TRANS_BYTES) {
+ dev_err(&ctrl->dev,
+ "pmic-arb supports 1..%d bytes per trans, but %d requested",
+ PMIC_ARB_MAX_TRANS_BYTES, len);
+ return -EINVAL;
+ }
+
+ /* Check the opcode */
+ if (opc >= 0x60 && opc <= 0x7F)
+ opc = PMIC_ARB_OP_READ;
+ else if (opc >= 0x20 && opc <= 0x2F)
+ opc = PMIC_ARB_OP_EXT_READ;
+ else if (opc >= 0x38 && opc <= 0x3F)
+ opc = PMIC_ARB_OP_EXT_READL;
+ else
+ return -EINVAL;
+
+ cmd = (opc << 27) | ((sid & 0xf) << 20) | (addr << 4) | (bc & 0x7);
+
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ if (rc)
+ goto done;
+
+ pa_read_data(pmic_arb, buf, PMIC_ARB_RDATA0(pmic_arb->channel),
+ min_t(u8, bc, 3));
+
+ if (bc > 3)
+ pa_read_data(pmic_arb, buf + 4,
+ PMIC_ARB_RDATA1(pmic_arb->channel), bc - 4);
+
+done:
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+ return rc;
+}
+
+static int pmic_arb_write_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
+ u16 addr, const u8 *buf, size_t len)
+{
+ struct spmi_pmic_arb_dev *pmic_arb = spmi_controller_get_drvdata(ctrl);
+ unsigned long flags;
+ u8 bc = len - 1;
+ u32 cmd;
+ int rc;
+
+ if (bc >= PMIC_ARB_MAX_TRANS_BYTES) {
+ dev_err(&ctrl->dev,
+ "pmic-arb supports 1..%d bytes per trans, but:%d requested",
+ PMIC_ARB_MAX_TRANS_BYTES, len);
+ return -EINVAL;
+ }
+
+ /* Check the opcode */
+ if (opc >= 0x40 && opc <= 0x5F)
+ opc = PMIC_ARB_OP_WRITE;
+ else if (opc >= 0x00 && opc <= 0x0F)
+ opc = PMIC_ARB_OP_EXT_WRITE;
+ else if (opc >= 0x30 && opc <= 0x37)
+ opc = PMIC_ARB_OP_EXT_WRITEL;
+ else if (opc >= 0x80 && opc <= 0xFF)
+ opc = PMIC_ARB_OP_ZERO_WRITE;
+ else
+ return -EINVAL;
+
+ cmd = (opc << 27) | ((sid & 0xf) << 20) | (addr << 4) | (bc & 0x7);
+
+ /* Write data to FIFOs */
+ spin_lock_irqsave(&pmic_arb->lock, flags);
+ pa_write_data(pmic_arb, buf, PMIC_ARB_WDATA0(pmic_arb->channel)
+ , min_t(u8, bc, 3));
+ if (bc > 3)
+ pa_write_data(pmic_arb, buf + 4,
+ PMIC_ARB_WDATA1(pmic_arb->channel), bc - 4);
+
+ /* Start the transaction */
+ pmic_arb_base_write(pmic_arb, PMIC_ARB_CMD(pmic_arb->channel), cmd);
+ rc = pmic_arb_wait_for_done(ctrl);
+ spin_unlock_irqrestore(&pmic_arb->lock, flags);
+
+ return rc;
+}
+
+static int spmi_pmic_arb_probe(struct platform_device *pdev)
+{
+ struct spmi_pmic_arb_dev *pa;
+ struct spmi_controller *ctrl;
+ struct resource *res;
+ u32 channel;
+ int err, i;
+
+ ctrl = spmi_controller_alloc(&pdev->dev, sizeof(*pa));
+ if (!ctrl)
+ return -ENOMEM;
+
+ pa = spmi_controller_get_drvdata(ctrl);
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "core");
+ pa->base = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->base)) {
+ err = PTR_ERR(pa->base);
+ goto err_put_ctrl;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "intr");
+ pa->intr = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->intr)) {
+ err = PTR_ERR(pa->intr);
+ goto err_put_ctrl;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cnfg");
+ pa->cnfg = devm_ioremap_resource(&ctrl->dev, res);
+ if (IS_ERR(pa->cnfg)) {
+ err = PTR_ERR(pa->cnfg);
+ goto err_put_ctrl;
+ }
+
+ err = of_property_read_u32(pdev->dev.of_node, "qcom,channel", &channel);
+ if (err) {
+ dev_err(&pdev->dev, "channel unspecified.\n");
+ goto err_put_ctrl;
+ }
+
+ if (channel > 5) {
+ dev_err(&pdev->dev, "invalid channel (%u) specified.\n",
+ channel);
+ goto err_put_ctrl;
+ }
+
+ pa->channel = channel;
+
+ platform_set_drvdata(pdev, ctrl);
+ spin_lock_init(&pa->lock);
+
+ ctrl->cmd = pmic_arb_cmd;
+ ctrl->read_cmd = pmic_arb_read_cmd;
+ ctrl->write_cmd = pmic_arb_write_cmd;
+
+ err = spmi_controller_add(ctrl);
+ if (err)
+ goto err_put_ctrl;
+
+ dev_dbg(&ctrl->dev, "PMIC Arb Version 0x%x\n",
+ pmic_arb_base_read(pa, PMIC_ARB_VERSION));
+
+ return 0;
+
+err_put_ctrl:
+ spmi_controller_put(ctrl);
+ return err;
+}
+
+static int spmi_pmic_arb_remove(struct platform_device *pdev)
+{
+ struct spmi_controller *ctrl = platform_get_drvdata(pdev);
+ spmi_controller_remove(ctrl);
+ spmi_controller_put(ctrl);
+ return 0;
+}
+
+static const struct of_device_id spmi_pmic_arb_match_table[] = {
+ { .compatible = "qcom,spmi-pmic-arb", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, spmi_pmic_arb_match_table);
+
+static struct platform_driver spmi_pmic_arb_driver = {
+ .probe = spmi_pmic_arb_probe,
+ .remove = spmi_pmic_arb_remove,
+ .driver = {
+ .name = "spmi_pmic_arb",
+ .owner = THIS_MODULE,
+ .of_match_table = spmi_pmic_arb_match_table,
+ },
+};
+module_platform_driver(spmi_pmic_arb_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:spmi_pmic_arb");
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 2/6] spmi: add generic SPMI controller binding documentation
From: Josh Cartwright @ 2014-02-03 23:05 UTC (permalink / raw)
To: Greg Kroah-Hartman, linux-kernel
Cc: Mark Rutland, devicetree, Pawel Moll, Ian Campbell, linux-arm-msm,
Gilad Avidov, linux-doc, Rob Herring, Michael Bohan, Rob Landley,
Kumar Gala, Sagar Dharia, linux-arm-kernel
In-Reply-To: <1391468739-20987-1-git-send-email-joshc@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
---
Documentation/devicetree/bindings/spmi/spmi.txt | 41 +++++++++++++++++++++++++
1 file changed, 41 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spmi/spmi.txt
diff --git a/Documentation/devicetree/bindings/spmi/spmi.txt b/Documentation/devicetree/bindings/spmi/spmi.txt
new file mode 100644
index 0000000..462a42f
--- /dev/null
+++ b/Documentation/devicetree/bindings/spmi/spmi.txt
@@ -0,0 +1,41 @@
+System Power Management Interface (SPMI) Controller
+
+This document defines a generic set of bindings for use by SPMI controllers. A
+controller is modelled in device tree as a node with zero or more child nodes,
+each representing a unique slave on the bus.
+
+Required properties:
+- #address-cells : must be set to 2
+- #size-cells : must be set to 0
+
+Child nodes:
+
+An SPMI controller node can contain zero or more child nodes representing slave
+devices on the bus. Child 'reg' properties are specified as an address, type
+pair. The address must be in the range 0-15 (4 bits). The type must be one of
+SPMI_USID (0) or SPMI_GSID (1) for Unique Slave ID or Group Slave ID respectively.
+These are the identifiers "statically assigned by the system integrator", as
+per the SPMI spec.
+
+Each child node must have one and only one 'reg' entry of type SPMI_USID.
+
+#include <dt-bindings/spmi/spmi.h>
+
+ spmi@.. {
+ compatible = "...";
+ reg = <...>;
+
+ #address-cells = <2>;
+ #size-cells <0>;
+
+ child@0 {
+ compatible = "...";
+ reg = <0 SPMI_USID>;
+ };
+
+ child@7 {
+ compatible = "...";
+ reg = <7 SPMI_USID
+ 3 SPMI_GSID>;
+ };
+ };
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 1/6] spmi: Linux driver framework for SPMI
From: Josh Cartwright @ 2014-02-03 23:05 UTC (permalink / raw)
To: Greg Kroah-Hartman, linux-kernel
Cc: linux-arm-kernel, linux-arm-msm, Sagar Dharia, Gilad Avidov,
Michael Bohan, Kenneth Heitke, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell, Kumar Gala, devicetree
In-Reply-To: <1391468739-20987-1-git-send-email-joshc@codeaurora.org>
From: Kenneth Heitke <kheitke@codeaurora.org>
System Power Management Interface (SPMI) is a specification
developed by the MIPI (Mobile Industry Process Interface) Alliance
optimized for the real time control of Power Management ICs (PMIC).
SPMI is a two-wire serial interface that supports up to 4 master
devices and up to 16 logical slaves.
The framework supports message APIs, multiple busses (1 controller
per bus) and multiple clients/slave devices per controller.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Michael Bohan <mbohan@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
---
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/spmi/Kconfig | 9 +
drivers/spmi/Makefile | 4 +
drivers/spmi/spmi.c | 609 ++++++++++++++++++++++++++++++++++++++++
include/dt-bindings/spmi/spmi.h | 18 ++
include/linux/mod_devicetable.h | 8 +
include/linux/spmi.h | 191 +++++++++++++
8 files changed, 842 insertions(+)
create mode 100644 drivers/spmi/Kconfig
create mode 100644 drivers/spmi/Makefile
create mode 100644 drivers/spmi/spmi.c
create mode 100644 include/dt-bindings/spmi/spmi.h
create mode 100644 include/linux/spmi.h
diff --git a/drivers/Kconfig b/drivers/Kconfig
index b3138fb..e0a4ae6 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -52,6 +52,8 @@ source "drivers/i2c/Kconfig"
source "drivers/spi/Kconfig"
+source "drivers/spmi/Kconfig"
+
source "drivers/hsi/Kconfig"
source "drivers/pps/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 8e3b8b0..3d6de8b 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -66,6 +66,7 @@ obj-$(CONFIG_ATA) += ata/
obj-$(CONFIG_TARGET_CORE) += target/
obj-$(CONFIG_MTD) += mtd/
obj-$(CONFIG_SPI) += spi/
+obj-$(CONFIG_SPMI) += spmi/
obj-y += hsi/
obj-y += net/
obj-$(CONFIG_ATM) += atm/
diff --git a/drivers/spmi/Kconfig b/drivers/spmi/Kconfig
new file mode 100644
index 0000000..1dbfee0
--- /dev/null
+++ b/drivers/spmi/Kconfig
@@ -0,0 +1,9 @@
+#
+# SPMI driver configuration
+#
+menuconfig SPMI
+ tristate "SPMI support"
+ help
+ SPMI (System Power Management Interface) is a two-wire
+ serial interface between baseband and application processors
+ and Power Management Integrated Circuits (PMIC).
diff --git a/drivers/spmi/Makefile b/drivers/spmi/Makefile
new file mode 100644
index 0000000..1de1acd
--- /dev/null
+++ b/drivers/spmi/Makefile
@@ -0,0 +1,4 @@
+#
+# Makefile for kernel SPMI framework.
+#
+obj-$(CONFIG_SPMI) += spmi.o
diff --git a/drivers/spmi/spmi.c b/drivers/spmi/spmi.c
new file mode 100644
index 0000000..6122c8f
--- /dev/null
+++ b/drivers/spmi/spmi.c
@@ -0,0 +1,609 @@
+/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/idr.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/spmi.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+
+#include <dt-bindings/spmi/spmi.h>
+
+static DEFINE_IDA(ctrl_ida);
+
+static void spmi_dev_release(struct device *dev)
+{
+ struct spmi_device *sdev = to_spmi_device(dev);
+ kfree(sdev);
+}
+
+static const struct device_type spmi_dev_type = {
+ .release = spmi_dev_release,
+};
+
+static void spmi_ctrl_release(struct device *dev)
+{
+ struct spmi_controller *ctrl = to_spmi_controller(dev);
+ ida_simple_remove(&ctrl_ida, ctrl->nr);
+ kfree(ctrl);
+}
+
+static const struct device_type spmi_ctrl_type = {
+ .release = spmi_ctrl_release,
+};
+
+#ifdef CONFIG_PM_RUNTIME
+static int spmi_runtime_suspend(struct device *dev)
+{
+ struct spmi_device *sdev = to_spmi_device(dev);
+ int err;
+
+ err = pm_generic_runtime_suspend(dev);
+ if (err)
+ return err;
+
+ return spmi_command_sleep(sdev);
+}
+
+static int spmi_runtime_resume(struct device *dev)
+{
+ struct spmi_device *sdev = to_spmi_device(dev);
+ int err;
+
+ err = spmi_command_wakeup(sdev);
+ if (err)
+ return err;
+
+ return pm_generic_runtime_resume(dev);
+}
+#endif
+
+static const struct dev_pm_ops spmi_pm_ops = {
+ SET_RUNTIME_PM_OPS(
+ spmi_runtime_suspend,
+ spmi_runtime_resume,
+ NULL
+ )
+};
+
+static int spmi_device_match(struct device *dev, struct device_driver *drv)
+{
+ if (of_driver_match_device(dev, drv))
+ return 1;
+
+ if (drv->name)
+ return strncmp(dev_name(dev), drv->name,
+ SPMI_NAME_SIZE) == 0;
+
+ return 0;
+}
+
+/**
+ * spmi_device_add() - add a device previously constructed via spmi_device_alloc()
+ * @sdev: spmi_device to be added
+ */
+int spmi_device_add(struct spmi_device *sdev)
+{
+ struct spmi_controller *ctrl = sdev->ctrl;
+ int err;
+
+ dev_set_name(&sdev->dev, "%d-%02x", ctrl->nr, sdev->usid);
+
+ err = device_add(&sdev->dev);
+ if (err < 0) {
+ dev_err(&sdev->dev, "Can't add %s, status %d\n",
+ dev_name(&sdev->dev), err);
+ goto err_device_add;
+ }
+
+ dev_dbg(&sdev->dev, "device %s registered\n", dev_name(&sdev->dev));
+
+err_device_add:
+ return err;
+}
+EXPORT_SYMBOL_GPL(spmi_device_add);
+
+/**
+ * spmi_device_remove(): remove an SPMI device
+ * @sdev: spmi_device to be removed
+ */
+void spmi_device_remove(struct spmi_device *sdev)
+{
+ device_unregister(&sdev->dev);
+}
+EXPORT_SYMBOL_GPL(spmi_device_remove);
+
+static inline int
+spmi_cmd(struct spmi_controller *ctrl, u8 opcode, u8 sid)
+{
+ if (!ctrl || !ctrl->cmd || ctrl->dev.type != &spmi_ctrl_type)
+ return -EINVAL;
+
+ return ctrl->cmd(ctrl, opcode, sid);
+}
+
+static inline int spmi_read_cmd(struct spmi_controller *ctrl, u8 opcode,
+ u8 sid, u16 addr, u8 *buf, size_t len)
+{
+ if (!ctrl || !ctrl->read_cmd || ctrl->dev.type != &spmi_ctrl_type)
+ return -EINVAL;
+
+ return ctrl->read_cmd(ctrl, opcode, sid, addr, buf, len);
+}
+
+static inline int spmi_write_cmd(struct spmi_controller *ctrl, u8 opcode,
+ u8 sid, u16 addr, const u8 *buf, size_t len)
+{
+ if (!ctrl || !ctrl->write_cmd || ctrl->dev.type != &spmi_ctrl_type)
+ return -EINVAL;
+
+ return ctrl->write_cmd(ctrl, opcode, sid, addr, buf, len);
+}
+
+/**
+ * spmi_register_read() - register read
+ * @sdev: SPMI device.
+ * @addr: slave register address (5-bit address).
+ * @buf: buffer to be populated with data from the Slave.
+ *
+ * Reads 1 byte of data from a Slave device register.
+ */
+int spmi_register_read(struct spmi_device *sdev, u8 addr, u8 *buf)
+{
+ /* 5-bit register address */
+ if (addr > 0x1F)
+ return -EINVAL;
+
+ return spmi_read_cmd(sdev->ctrl, SPMI_CMD_READ, sdev->usid, addr,
+ buf, 1);
+}
+EXPORT_SYMBOL_GPL(spmi_register_read);
+
+/**
+ * spmi_ext_register_read() - extended register read
+ * @sdev: SPMI device.
+ * @addr: slave register address (8-bit address).
+ * @buf: buffer to be populated with data from the Slave.
+ * @len: the request number of bytes to read (up to 16 bytes).
+ *
+ * Reads up to 16 bytes of data from the extended register space on a
+ * Slave device.
+ */
+int spmi_ext_register_read(struct spmi_device *sdev, u8 addr, u8 *buf,
+ size_t len)
+{
+ /* 8-bit register address, up to 16 bytes */
+ if (len == 0 || len > 16)
+ return -EINVAL;
+
+ return spmi_read_cmd(sdev->ctrl, SPMI_CMD_EXT_READ, sdev->usid, addr,
+ buf, len);
+}
+EXPORT_SYMBOL_GPL(spmi_ext_register_read);
+
+/**
+ * spmi_ext_register_readl() - extended register read long
+ * @sdev: SPMI device.
+ * @addr: slave register address (16-bit address).
+ * @buf: buffer to be populated with data from the Slave.
+ * @len: the request number of bytes to read (up to 8 bytes).
+ *
+ * Reads up to 8 bytes of data from the extended register space on a
+ * Slave device using 16-bit address.
+ */
+int spmi_ext_register_readl(struct spmi_device *sdev, u16 addr, u8 *buf,
+ size_t len)
+{
+ /* 16-bit register address, up to 8 bytes */
+ if (len == 0 || len > 8)
+ return -EINVAL;
+
+ return spmi_read_cmd(sdev->ctrl, SPMI_CMD_EXT_READL, sdev->usid, addr,
+ buf, len);
+}
+EXPORT_SYMBOL_GPL(spmi_ext_register_readl);
+
+/**
+ * spmi_register_write() - register write
+ * @sdev: SPMI device
+ * @addr: slave register address (5-bit address).
+ * @data: buffer containing the data to be transferred to the Slave.
+ *
+ * Writes 1 byte of data to a Slave device register.
+ */
+int spmi_register_write(struct spmi_device *sdev, u8 addr, u8 data)
+{
+ /* 5-bit register address */
+ if (addr > 0x1F)
+ return -EINVAL;
+
+ return spmi_write_cmd(sdev->ctrl, SPMI_CMD_WRITE, sdev->usid, addr,
+ &data, 1);
+}
+EXPORT_SYMBOL_GPL(spmi_register_write);
+
+/**
+ * spmi_register_zero_write() - register zero write
+ * @sdev: SPMI device.
+ * @data: the data to be written to register 0 (7-bits).
+ *
+ * Writes data to register 0 of the Slave device.
+ */
+int spmi_register_zero_write(struct spmi_device *sdev, u8 data)
+{
+ return spmi_write_cmd(sdev->ctrl, SPMI_CMD_ZERO_WRITE, sdev->usid, 0,
+ &data, 1);
+}
+EXPORT_SYMBOL_GPL(spmi_register_zero_write);
+
+/**
+ * spmi_ext_register_write() - extended register write
+ * @sdev: SPMI device.
+ * @addr: slave register address (8-bit address).
+ * @buf: buffer containing the data to be transferred to the Slave.
+ * @len: the request number of bytes to read (up to 16 bytes).
+ *
+ * Writes up to 16 bytes of data to the extended register space of a
+ * Slave device.
+ */
+int spmi_ext_register_write(struct spmi_device *sdev, u8 addr, const u8 *buf,
+ size_t len)
+{
+ /* 8-bit register address, up to 16 bytes */
+ if (len == 0 || len > 16)
+ return -EINVAL;
+
+ return spmi_write_cmd(sdev->ctrl, SPMI_CMD_EXT_WRITE, sdev->usid, addr,
+ buf, len);
+}
+EXPORT_SYMBOL_GPL(spmi_ext_register_write);
+
+/**
+ * spmi_ext_register_writel() - extended register write long
+ * @sdev: SPMI device.
+ * @addr: slave register address (16-bit address).
+ * @buf: buffer containing the data to be transferred to the Slave.
+ * @len: the request number of bytes to read (up to 8 bytes).
+ *
+ * Writes up to 8 bytes of data to the extended register space of a
+ * Slave device using 16-bit address.
+ */
+int spmi_ext_register_writel(struct spmi_device *sdev, u16 addr, const u8 *buf,
+ size_t len)
+{
+ /* 4-bit Slave Identifier, 16-bit register address, up to 8 bytes */
+ if (len == 0 || len > 8)
+ return -EINVAL;
+
+ return spmi_write_cmd(sdev->ctrl, SPMI_CMD_EXT_WRITEL, sdev->usid,
+ addr, buf, len);
+}
+EXPORT_SYMBOL_GPL(spmi_ext_register_writel);
+
+/**
+ * spmi_command_reset() - sends RESET command to the specified slave
+ * @sdev: SPMI device.
+ *
+ * The Reset command initializes the Slave and forces all registers to
+ * their reset values. The Slave shall enter the STARTUP state after
+ * receiving a Reset command.
+ */
+int spmi_command_reset(struct spmi_device *sdev)
+{
+ return spmi_cmd(sdev->ctrl, SPMI_CMD_RESET, sdev->usid);
+}
+EXPORT_SYMBOL_GPL(spmi_command_reset);
+
+/**
+ * spmi_command_sleep() - sends SLEEP command to the specified SPMI device
+ * @sdev: SPMI device.
+ *
+ * The Sleep command causes the Slave to enter the user defined SLEEP state.
+ */
+int spmi_command_sleep(struct spmi_device *sdev)
+{
+ return spmi_cmd(sdev->ctrl, SPMI_CMD_SLEEP, sdev->usid);
+}
+EXPORT_SYMBOL_GPL(spmi_command_sleep);
+
+/**
+ * spmi_command_wakeup() - sends WAKEUP command to the specified SPMI device
+ * @sdev: SPMI device.
+ *
+ * The Wakeup command causes the Slave to move from the SLEEP state to
+ * the ACTIVE state.
+ */
+int spmi_command_wakeup(struct spmi_device *sdev)
+{
+ return spmi_cmd(sdev->ctrl, SPMI_CMD_WAKEUP, sdev->usid);
+}
+EXPORT_SYMBOL_GPL(spmi_command_wakeup);
+
+/**
+ * spmi_command_shutdown() - sends SHUTDOWN command to the specified SPMI device
+ * @sdev: SPMI device.
+ *
+ * The Shutdown command causes the Slave to enter the SHUTDOWN state.
+ */
+int spmi_command_shutdown(struct spmi_device *sdev)
+{
+ return spmi_cmd(sdev->ctrl, SPMI_CMD_SHUTDOWN, sdev->usid);
+}
+EXPORT_SYMBOL_GPL(spmi_command_shutdown);
+
+static int spmi_drv_probe(struct device *dev)
+{
+ const struct spmi_driver *sdrv = to_spmi_driver(dev->driver);
+ struct spmi_device *sdev = to_spmi_device(dev);
+ int err;
+
+ /* Ensure the slave is in ACTIVE state */
+ err = spmi_command_wakeup(sdev);
+ if (err)
+ goto fail_wakeup;
+
+ pm_runtime_get_noresume(dev);
+ pm_runtime_set_active(dev);
+ pm_runtime_enable(dev);
+
+ err = sdrv->probe(sdev);
+ if (err)
+ goto fail_probe;
+
+ return 0;
+
+fail_probe:
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_put_noidle(dev);
+fail_wakeup:
+ return err;
+}
+
+static int spmi_drv_remove(struct device *dev)
+{
+ const struct spmi_driver *sdrv = to_spmi_driver(dev->driver);
+
+ pm_runtime_get_sync(dev);
+ sdrv->remove(to_spmi_device(dev));
+ pm_runtime_put_noidle(dev);
+
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_put_noidle(dev);
+ return 0;
+}
+
+static struct bus_type spmi_bus_type = {
+ .name = "spmi",
+ .match = spmi_device_match,
+ .pm = &spmi_pm_ops,
+ .probe = spmi_drv_probe,
+ .remove = spmi_drv_remove,
+};
+
+/**
+ * spmi_controller_alloc() - Allocate a new SPMI device
+ * @ctrl: associated controller
+ *
+ * Caller is responsible for either calling spmi_device_add() to add the
+ * newly allocated controller, or calling spmi_device_put() to discard it.
+ */
+struct spmi_device *spmi_device_alloc(struct spmi_controller *ctrl)
+{
+ struct spmi_device *sdev;
+
+ sdev = kzalloc(sizeof(*sdev), GFP_KERNEL);
+ if (!sdev)
+ return NULL;
+
+ sdev->ctrl = ctrl;
+ device_initialize(&sdev->dev);
+ sdev->dev.parent = &ctrl->dev;
+ sdev->dev.bus = &spmi_bus_type;
+ sdev->dev.type = &spmi_dev_type;
+ return sdev;
+}
+EXPORT_SYMBOL_GPL(spmi_device_alloc);
+
+/**
+ * spmi_controller_alloc() - Allocate a new SPMI controller
+ * @parent: parent device
+ * @size: size of private data
+ *
+ * Caller is responsible for either calling spmi_controller_add() to add the
+ * newly allocated controller, or calling spmi_controller_put() to discard it.
+ * The allocated private data region may be accessed via
+ * spmi_controller_get_drvdata()
+ */
+struct spmi_controller *spmi_controller_alloc(struct device *parent,
+ size_t size)
+{
+ struct spmi_controller *ctrl;
+ int id;
+
+ if (WARN_ON(!parent))
+ return NULL;
+
+ ctrl = kzalloc(sizeof(*ctrl) + size, GFP_KERNEL);
+ if (!ctrl)
+ return NULL;
+
+ device_initialize(&ctrl->dev);
+ ctrl->dev.type = &spmi_ctrl_type;
+ ctrl->dev.bus = &spmi_bus_type;
+ ctrl->dev.parent = parent;
+ ctrl->dev.of_node = parent->of_node;
+ spmi_controller_set_drvdata(ctrl, &ctrl[1]);
+
+ id = ida_simple_get(&ctrl_ida, 0, 0, GFP_KERNEL);
+ if (id < 0) {
+ dev_err(parent,
+ "unable to allocate SPMI controller identifier.\n");
+ spmi_controller_put(ctrl);
+ return NULL;
+ }
+
+ ctrl->nr = id;
+ dev_set_name(&ctrl->dev, "spmi-%d", id);
+
+ dev_dbg(&ctrl->dev, "allocated controller 0x%p id %d\n", ctrl, id);
+ return ctrl;
+}
+EXPORT_SYMBOL_GPL(spmi_controller_alloc);
+
+static void of_spmi_register_devices(struct spmi_controller *ctrl)
+{
+ struct device_node *node;
+ int err;
+
+ if (!ctrl->dev.of_node)
+ return;
+
+ for_each_available_child_of_node(ctrl->dev.of_node, node) {
+ struct spmi_device *sdev;
+ u32 reg[2];
+
+ dev_dbg(&ctrl->dev, "adding child %s\n", node->full_name);
+
+ err = of_property_read_u32_array(node, "reg", reg, 2);
+ if (err) {
+ dev_err(&ctrl->dev,
+ "node %s err (%d) does not have 'reg' property\n",
+ node->full_name, err);
+ continue;
+ }
+
+ if (reg[1] != SPMI_USID) {
+ dev_err(&ctrl->dev,
+ "node %s contains unsupported 'reg' entry\n",
+ node->full_name);
+ continue;
+ }
+
+ if (reg[0] >= SPMI_MAX_SLAVE_ID) {
+ dev_err(&ctrl->dev,
+ "invalid usid on node %s\n",
+ node->full_name);
+ continue;
+ }
+
+ dev_dbg(&ctrl->dev, "read usid %02x\n", reg[0]);
+
+ sdev = spmi_device_alloc(ctrl);
+ if (!sdev)
+ continue;
+
+ sdev->dev.of_node = node;
+ sdev->usid = (u8) reg[0];
+
+ err = spmi_device_add(sdev);
+ if (err) {
+ dev_err(&sdev->dev,
+ "failure adding device. status %d\n", err);
+ spmi_device_put(sdev);
+ }
+ }
+}
+
+/**
+ * spmi_controller_add() - Add an SPMI controller
+ * @ctrl: controller to be registered.
+ *
+ * Register a controller previously allocated via spmi_controller_alloc() with
+ * the SPMI core.
+ */
+int spmi_controller_add(struct spmi_controller *ctrl)
+{
+ int ret;
+
+ /* Can't register until after driver model init */
+ if (WARN_ON(!spmi_bus_type.p))
+ return -EAGAIN;
+
+ ret = device_add(&ctrl->dev);
+ if (ret)
+ return ret;
+
+ if (IS_ENABLED(CONFIG_OF))
+ of_spmi_register_devices(ctrl);
+
+ dev_dbg(&ctrl->dev, "spmi-%d registered: dev:%p\n",
+ ctrl->nr, &ctrl->dev);
+
+ return 0;
+};
+EXPORT_SYMBOL_GPL(spmi_controller_add);
+
+/* Remove a device associated with a controller */
+static int spmi_ctrl_remove_device(struct device *dev, void *data)
+{
+ struct spmi_device *spmidev = to_spmi_device(dev);
+ if (dev->type == &spmi_dev_type)
+ spmi_device_remove(spmidev);
+ return 0;
+}
+
+/**
+ * spmi_controller_remove(): remove an SPMI controller
+ * @ctrl: controller to remove
+ *
+ * Remove a SPMI controller. Caller is responsible for calling
+ * spmi_controller_put() to discard the allocated controller.
+ */
+void spmi_controller_remove(struct spmi_controller *ctrl)
+{
+ int dummy;
+
+ if (!ctrl)
+ return;
+
+ dummy = device_for_each_child(&ctrl->dev, NULL,
+ spmi_ctrl_remove_device);
+ device_del(&ctrl->dev);
+}
+EXPORT_SYMBOL_GPL(spmi_controller_remove);
+
+/**
+ * spmi_driver_register() - Register client driver with SPMI core
+ * @sdrv: client driver to be associated with client-device.
+ *
+ * This API will register the client driver with the SPMI framework.
+ * It is typically called from the driver's module-init function.
+ */
+int spmi_driver_register(struct spmi_driver *sdrv)
+{
+ sdrv->driver.bus = &spmi_bus_type;
+ return driver_register(&sdrv->driver);
+}
+EXPORT_SYMBOL_GPL(spmi_driver_register);
+
+static void __exit spmi_exit(void)
+{
+ bus_unregister(&spmi_bus_type);
+}
+module_exit(spmi_exit);
+
+static int __init spmi_init(void)
+{
+ return bus_register(&spmi_bus_type);
+}
+postcore_initcall(spmi_init);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("SPMI module");
+MODULE_ALIAS("platform:spmi");
diff --git a/include/dt-bindings/spmi/spmi.h b/include/dt-bindings/spmi/spmi.h
new file mode 100644
index 0000000..d11e1e5
--- /dev/null
+++ b/include/dt-bindings/spmi/spmi.h
@@ -0,0 +1,18 @@
+/* Copyright (c) 2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef __DT_BINDINGS_SPMI_H
+#define __DT_BINDINGS_SPMI_H
+
+#define SPMI_USID 0
+#define SPMI_GSID 1
+
+#endif
diff --git a/include/linux/mod_devicetable.h b/include/linux/mod_devicetable.h
index 45e9214..677e474 100644
--- a/include/linux/mod_devicetable.h
+++ b/include/linux/mod_devicetable.h
@@ -432,6 +432,14 @@ struct spi_device_id {
kernel_ulong_t driver_data; /* Data private to the driver */
};
+#define SPMI_NAME_SIZE 32
+#define SPMI_MODULE_PREFIX "spmi:"
+
+struct spmi_device_id {
+ char name[SPMI_NAME_SIZE];
+ kernel_ulong_t driver_data; /* Data private to the driver */
+};
+
/* dmi */
enum dmi_field {
DMI_NONE,
diff --git a/include/linux/spmi.h b/include/linux/spmi.h
new file mode 100644
index 0000000..91f5eab
--- /dev/null
+++ b/include/linux/spmi.h
@@ -0,0 +1,191 @@
+/* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef _LINUX_SPMI_H
+#define _LINUX_SPMI_H
+
+#include <linux/types.h>
+#include <linux/device.h>
+#include <linux/mod_devicetable.h>
+
+/* Maximum slave identifier */
+#define SPMI_MAX_SLAVE_ID 16
+
+/* SPMI Commands */
+#define SPMI_CMD_EXT_WRITE 0x00
+#define SPMI_CMD_RESET 0x10
+#define SPMI_CMD_SLEEP 0x11
+#define SPMI_CMD_SHUTDOWN 0x12
+#define SPMI_CMD_WAKEUP 0x13
+#define SPMI_CMD_AUTHENTICATE 0x14
+#define SPMI_CMD_MSTR_READ 0x15
+#define SPMI_CMD_MSTR_WRITE 0x16
+#define SPMI_CMD_TRANSFER_BUS_OWNERSHIP 0x1A
+#define SPMI_CMD_DDB_MASTER_READ 0x1B
+#define SPMI_CMD_DDB_SLAVE_READ 0x1C
+#define SPMI_CMD_EXT_READ 0x20
+#define SPMI_CMD_EXT_WRITEL 0x30
+#define SPMI_CMD_EXT_READL 0x38
+#define SPMI_CMD_WRITE 0x40
+#define SPMI_CMD_READ 0x60
+#define SPMI_CMD_ZERO_WRITE 0x80
+
+/**
+ * struct spmi_device - Basic representation of an SPMI device
+ * @dev: Driver model representation of the device.
+ * @ctrl: SPMI controller managing the bus hosting this device.
+ * @usid: This devices' Unique Slave IDentifier.
+ */
+struct spmi_device {
+ struct device dev;
+ struct spmi_controller *ctrl;
+ u8 usid;
+};
+
+static inline struct spmi_device *to_spmi_device(struct device *d)
+{
+ return container_of(d, struct spmi_device, dev);
+}
+
+static inline void *spmi_device_get_drvdata(const struct spmi_device *sdev)
+{
+ return dev_get_drvdata(&sdev->dev);
+}
+
+static inline void spmi_device_set_drvdata(struct spmi_device *sdev, void *data)
+{
+ dev_set_drvdata(&sdev->dev, data);
+}
+
+struct spmi_device *spmi_device_alloc(struct spmi_controller *ctrl);
+
+static inline void spmi_device_put(struct spmi_device *sdev)
+{
+ if (sdev)
+ put_device(&sdev->dev);
+}
+
+int spmi_device_add(struct spmi_device *sdev);
+
+void spmi_device_remove(struct spmi_device *sdev);
+
+/**
+ * struct spmi_controller - interface to the SPMI master controller
+ * @dev: Driver model representation of the device.
+ * @nr: board-specific number identifier for this controller/bus
+ * @cmd: sends a non-data command sequence on the SPMI bus.
+ * @read_cmd: sends a register read command sequence on the SPMI bus.
+ * @write_cmd: sends a register write command sequence on the SPMI bus.
+ */
+struct spmi_controller {
+ struct device dev;
+ unsigned int nr;
+ int (*cmd)(struct spmi_controller *ctrl, u8 opcode, u8 sid);
+ int (*read_cmd)(struct spmi_controller *ctrl, u8 opcode,
+ u8 sid, u16 addr, u8 *buf, size_t len);
+ int (*write_cmd)(struct spmi_controller *ctrl, u8 opcode,
+ u8 sid, u16 addr, const u8 *buf, size_t len);
+};
+
+static inline struct spmi_controller *to_spmi_controller(struct device *d)
+{
+ return container_of(d, struct spmi_controller, dev);
+}
+
+static inline
+void *spmi_controller_get_drvdata(const struct spmi_controller *ctrl)
+{
+ return dev_get_drvdata(&ctrl->dev);
+}
+
+static inline void spmi_controller_set_drvdata(struct spmi_controller *ctrl,
+ void *data)
+{
+ dev_set_drvdata(&ctrl->dev, data);
+}
+
+struct spmi_controller *spmi_controller_alloc(struct device *parent,
+ size_t size);
+
+/**
+ * spmi_controller_put() - decrement controller refcount
+ * @ctrl SPMI controller.
+ */
+static inline void spmi_controller_put(struct spmi_controller *ctrl)
+{
+ if (ctrl)
+ put_device(&ctrl->dev);
+}
+
+int spmi_controller_add(struct spmi_controller *ctrl);
+void spmi_controller_remove(struct spmi_controller *ctrl);
+
+/**
+ * struct spmi_driver - SPMI slave device driver
+ * @driver: SPMI device drivers should initialize name and owner field of
+ * this structure.
+ * @probe: binds this driver to a SPMI device.
+ * @remove: unbinds this driver from the SPMI device.
+ * @shutdown: standard shutdown callback used during powerdown/halt.
+ * @suspend: standard suspend callback used during system suspend.
+ * @resume: standard resume callback used during system resume.
+ *
+ * If PM runtime support is desired for a slave, a device driver can call
+ * pm_runtime_put() from their probe() routine (and a balancing
+ * pm_runtime_get() in remove()). PM runtime support for a slave is
+ * implemented by issuing a SLEEP command to the slave on runtime_suspend(),
+ * transitioning the slave into the SLEEP state. On runtime_resume(), a WAKEUP
+ * command is sent to the slave to bring it back to ACTIVE.
+ */
+struct spmi_driver {
+ struct device_driver driver;
+ int (*probe)(struct spmi_device *sdev);
+ void (*remove)(struct spmi_device *sdev);
+};
+
+static inline struct spmi_driver *to_spmi_driver(struct device_driver *d)
+{
+ return container_of(d, struct spmi_driver, driver);
+}
+
+int spmi_driver_register(struct spmi_driver *sdrv);
+
+/**
+ * spmi_driver_unregister() - unregister an SPMI client driver
+ * @sdrv: the driver to unregister
+ */
+static inline void spmi_driver_unregister(struct spmi_driver *sdrv)
+{
+ if (sdrv)
+ driver_unregister(&sdrv->driver);
+}
+
+#define module_spmi_driver(__spmi_driver) \
+ module_driver(__spmi_driver, spmi_driver_register, \
+ spmi_driver_unregister)
+
+int spmi_register_read(struct spmi_device *sdev, u8 addr, u8 *buf);
+int spmi_ext_register_read(struct spmi_device *sdev, u8 addr, u8 *buf,
+ size_t len);
+int spmi_ext_register_readl(struct spmi_device *sdev, u16 addr, u8 *buf,
+ size_t len);
+int spmi_register_write(struct spmi_device *sdev, u8 addr, u8 data);
+int spmi_register_zero_write(struct spmi_device *sdev, u8 data);
+int spmi_ext_register_write(struct spmi_device *sdev, u8 addr,
+ const u8 *buf, size_t len);
+int spmi_ext_register_writel(struct spmi_device *sdev, u16 addr,
+ const u8 *buf, size_t len);
+int spmi_command_reset(struct spmi_device *sdev);
+int spmi_command_sleep(struct spmi_device *sdev);
+int spmi_command_wakeup(struct spmi_device *sdev);
+int spmi_command_shutdown(struct spmi_device *sdev);
+
+#endif
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [Patch v4 2/2] dmaengine: qcom_bam_dma: Add device tree binding
From: Andy Gross @ 2014-02-03 23:04 UTC (permalink / raw)
To: Vinod Koul, Dan Williams, dmaengine
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-arm-msm,
Andy Gross
In-Reply-To: <1391468687-4347-1-git-send-email-agross@codeaurora.org>
Add device tree binding support for the QCOM BAM DMA driver.
Signed-off-by: Andy Gross <agross@codeaurora.org>
---
.../devicetree/bindings/dma/qcom_bam_dma.txt | 48 ++++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
diff --git a/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
new file mode 100644
index 0000000..86344f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
@@ -0,0 +1,48 @@
+QCOM BAM DMA controller
+
+Required properties:
+- compatible: Must be "qcom,bam-v1.4.0" for MSM8974 V1
+ Must be "qcom,bam-v1.4.1" for MSM8974 V2
+- reg: Address range for DMA registers
+- interrupts: single interrupt for this controller
+- #dma-cells: must be <1>
+- clocks: required clock
+- clock-names: name of clock
+- qcom,ee : indicates the active Execution Environment identifier (0-7)
+
+Example:
+
+ uart-bam: dma@f9984000 = {
+ compatible = "qcom,bam-v1.4.1";
+ reg = <0xf9984000 0x15000>;
+ interrupts = <0 94 0>;
+ clocks = <&gcc GCC_BAM_DMA_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ };
+
+Client:
+Required properties:
+- dmas: List of dma channel requests
+- dma-names: Names of aforementioned requested channels
+
+Clients must use the format described in the dma.txt file, using a two cell
+specifier for each channel.
+
+The three cells in order are:
+ 1. A phandle pointing to the DMA controller
+ 2. The channel number
+
+Example:
+ serial@f991e000 {
+ compatible = "qcom,msm-uart";
+ reg = <0xf991e000 0x1000>
+ <0xf9944000 0x19000>;
+ interrupts = <0 108 0>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+
+ dmas = <&uart-bam 0>, <&uart-bam 1>;
+ dma-names = "rx", "tx";
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [Patch v4 1/2] dmaengine: add Qualcomm BAM dma driver
From: Andy Gross @ 2014-02-03 23:04 UTC (permalink / raw)
To: Vinod Koul, Dan Williams, dmaengine
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-arm-msm,
Andy Gross
In-Reply-To: <1391468687-4347-1-git-send-email-agross@codeaurora.org>
Add the DMA engine driver for the QCOM Bus Access Manager (BAM) DMA controller
found in the MSM 8x74 platforms.
Each BAM DMA device is associated with a specific on-chip peripheral. Each
channel provides a uni-directional data transfer engine that is capable of
transferring data between the peripheral and system memory (System mode), or
between two peripherals (BAM2BAM).
The initial release of this driver only supports slave transfers between
peripherals and system memory.
Signed-off-by: Andy Gross <agross@codeaurora.org>
---
drivers/dma/Kconfig | 9 +
drivers/dma/Makefile | 1 +
drivers/dma/qcom_bam_dma.c | 1059 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1069 insertions(+)
create mode 100644 drivers/dma/qcom_bam_dma.c
diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index c10eb89..1b2f6cf 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -386,4 +386,13 @@ config DMATEST
config DMA_ENGINE_RAID
bool
+config QCOM_BAM_DMA
+ tristate "QCOM BAM DMA support"
+ depends on ARCH_MSM_DT || (COMPILE_TEST && OF && ARM)
+ select DMA_ENGINE
+ select DMA_VIRTUAL_CHANNELS
+ ---help---
+ Enable support for the QCOM BAM DMA controller. This controller
+ provides DMA capabilities for a variety of on-chip devices.
+
endif
diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile
index 0ce2da9..7ef950a 100644
--- a/drivers/dma/Makefile
+++ b/drivers/dma/Makefile
@@ -42,3 +42,4 @@ obj-$(CONFIG_MMP_PDMA) += mmp_pdma.o
obj-$(CONFIG_DMA_JZ4740) += dma-jz4740.o
obj-$(CONFIG_TI_CPPI41) += cppi41.o
obj-$(CONFIG_K3_DMA) += k3dma.o
+obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o
diff --git a/drivers/dma/qcom_bam_dma.c b/drivers/dma/qcom_bam_dma.c
new file mode 100644
index 0000000..a4ac0db
--- /dev/null
+++ b/drivers/dma/qcom_bam_dma.c
@@ -0,0 +1,1059 @@
+/*
+ * QCOM BAM DMA engine driver
+ *
+ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ *
+ * QCOM BAM DMA blocks are distributed amongst a number of the on-chip
+ * peripherals on the MSM 8x74. The configuration of the channels are dependent
+ * on the way they are hard wired to that specific peripheral. The peripheral
+ * device tree entries specify the configuration of each channel.
+ *
+ * The DMA controller requires the use of external memory for storage of the
+ * hardware descriptors for each channel. The descriptor FIFO is accessed as a
+ * circular buffer and operations are managed according to the offset within the
+ * FIFO. After pipe/channel reset, all of the pipe registers and internal state
+ * are back to defaults.
+ *
+ * During DMA operations, we write descriptors to the FIFO, being careful to
+ * handle wrapping and then write the last FIFO offset to that channel's
+ * P_EVNT_REG register to kick off the transaction. The P_SW_OFSTS register
+ * indicates the current FIFO offset that is being processed, so there is some
+ * indication of where the hardware is currently working.
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_dma.h>
+#include <linux/clk.h>
+#include <linux/dmaengine.h>
+
+#include "dmaengine.h"
+#include "virt-dma.h"
+
+struct bam_desc_hw {
+ u32 addr; /* Buffer physical address */
+ u16 size; /* Buffer size in bytes */
+ u16 flags;
+};
+
+#define DESC_FLAG_INT BIT(15)
+#define DESC_FLAG_EOT BIT(14)
+#define DESC_FLAG_EOB BIT(13)
+
+struct bam_async_desc {
+ struct virt_dma_desc vd;
+
+ u32 num_desc;
+ u32 xfer_len;
+ struct bam_desc_hw *curr_desc;
+
+ enum dma_transfer_direction dir;
+ size_t length;
+ struct bam_desc_hw desc[0];
+};
+
+#define BAM_CTRL 0x0000
+#define BAM_REVISION 0x0004
+#define BAM_SW_REVISION 0x0080
+#define BAM_NUM_PIPES 0x003C
+#define BAM_TIMER 0x0040
+#define BAM_TIMER_CTRL 0x0044
+#define BAM_DESC_CNT_TRSHLD 0x0008
+#define BAM_IRQ_SRCS 0x000C
+#define BAM_IRQ_SRCS_MSK 0x0010
+#define BAM_IRQ_SRCS_UNMASKED 0x0030
+#define BAM_IRQ_STTS 0x0014
+#define BAM_IRQ_CLR 0x0018
+#define BAM_IRQ_EN 0x001C
+#define BAM_CNFG_BITS 0x007C
+#define BAM_IRQ_SRCS_EE(pipe) (0x0800 + ((pipe) * 0x80))
+#define BAM_IRQ_SRCS_MSK_EE(pipe) (0x0804 + ((pipe) * 0x80))
+#define BAM_P_CTRL(pipe) (0x1000 + ((pipe) * 0x1000))
+#define BAM_P_RST(pipe) (0x1004 + ((pipe) * 0x1000))
+#define BAM_P_HALT(pipe) (0x1008 + ((pipe) * 0x1000))
+#define BAM_P_IRQ_STTS(pipe) (0x1010 + ((pipe) * 0x1000))
+#define BAM_P_IRQ_CLR(pipe) (0x1014 + ((pipe) * 0x1000))
+#define BAM_P_IRQ_EN(pipe) (0x1018 + ((pipe) * 0x1000))
+#define BAM_P_EVNT_DEST_ADDR(pipe) (0x182C + ((pipe) * 0x1000))
+#define BAM_P_EVNT_REG(pipe) (0x1818 + ((pipe) * 0x1000))
+#define BAM_P_SW_OFSTS(pipe) (0x1800 + ((pipe) * 0x1000))
+#define BAM_P_DATA_FIFO_ADDR(pipe) (0x1824 + ((pipe) * 0x1000))
+#define BAM_P_DESC_FIFO_ADDR(pipe) (0x181C + ((pipe) * 0x1000))
+#define BAM_P_EVNT_TRSHLD(pipe) (0x1828 + ((pipe) * 0x1000))
+#define BAM_P_FIFO_SIZES(pipe) (0x1820 + ((pipe) * 0x1000))
+
+/* BAM CTRL */
+#define BAM_SW_RST BIT(0)
+#define BAM_EN BIT(1)
+#define BAM_EN_ACCUM BIT(4)
+#define BAM_TESTBUS_SEL_SHIFT 5
+#define BAM_TESTBUS_SEL_MASK 0x3F
+#define BAM_DESC_CACHE_SEL_SHIFT 13
+#define BAM_DESC_CACHE_SEL_MASK 0x3
+#define BAM_CACHED_DESC_STORE BIT(15)
+#define IBC_DISABLE BIT(16)
+
+/* BAM REVISION */
+#define REVISION_SHIFT 0
+#define REVISION_MASK 0xFF
+#define NUM_EES_SHIFT 8
+#define NUM_EES_MASK 0xF
+#define CE_BUFFER_SIZE BIT(13)
+#define AXI_ACTIVE BIT(14)
+#define USE_VMIDMT BIT(15)
+#define SECURED BIT(16)
+#define BAM_HAS_NO_BYPASS BIT(17)
+#define HIGH_FREQUENCY_BAM BIT(18)
+#define INACTIV_TMRS_EXST BIT(19)
+#define NUM_INACTIV_TMRS BIT(20)
+#define DESC_CACHE_DEPTH_SHIFT 21
+#define DESC_CACHE_DEPTH_1 (0 << DESC_CACHE_DEPTH_SHIFT)
+#define DESC_CACHE_DEPTH_2 (1 << DESC_CACHE_DEPTH_SHIFT)
+#define DESC_CACHE_DEPTH_3 (2 << DESC_CACHE_DEPTH_SHIFT)
+#define DESC_CACHE_DEPTH_4 (3 << DESC_CACHE_DEPTH_SHIFT)
+#define CMD_DESC_EN BIT(23)
+#define INACTIV_TMR_BASE_SHIFT 24
+#define INACTIV_TMR_BASE_MASK 0xFF
+
+/* BAM NUM PIPES */
+#define BAM_NUM_PIPES_SHIFT 0
+#define BAM_NUM_PIPES_MASK 0xFF
+#define PERIPH_NON_PIPE_GRP_SHIFT 16
+#define PERIPH_NON_PIP_GRP_MASK 0xFF
+#define BAM_NON_PIPE_GRP_SHIFT 24
+#define BAM_NON_PIPE_GRP_MASK 0xFF
+
+/* BAM CNFG BITS */
+#define BAM_PIPE_CNFG BIT(2)
+#define BAM_FULL_PIPE BIT(11)
+#define BAM_NO_EXT_P_RST BIT(12)
+#define BAM_IBC_DISABLE BIT(13)
+#define BAM_SB_CLK_REQ BIT(14)
+#define BAM_PSM_CSW_REQ BIT(15)
+#define BAM_PSM_P_RES BIT(16)
+#define BAM_AU_P_RES BIT(17)
+#define BAM_SI_P_RES BIT(18)
+#define BAM_WB_P_RES BIT(19)
+#define BAM_WB_BLK_CSW BIT(20)
+#define BAM_WB_CSW_ACK_IDL BIT(21)
+#define BAM_WB_RETR_SVPNT BIT(22)
+#define BAM_WB_DSC_AVL_P_RST BIT(23)
+#define BAM_REG_P_EN BIT(24)
+#define BAM_PSM_P_HD_DATA BIT(25)
+#define BAM_AU_ACCUMED BIT(26)
+#define BAM_CMD_ENABLE BIT(27)
+
+#define BAM_CNFG_BITS_DEFAULT (BAM_PIPE_CNFG | \
+ BAM_NO_EXT_P_RST | \
+ BAM_IBC_DISABLE | \
+ BAM_SB_CLK_REQ | \
+ BAM_PSM_CSW_REQ | \
+ BAM_PSM_P_RES | \
+ BAM_AU_P_RES | \
+ BAM_SI_P_RES | \
+ BAM_WB_P_RES | \
+ BAM_WB_BLK_CSW | \
+ BAM_WB_CSW_ACK_IDL | \
+ BAM_WB_RETR_SVPNT | \
+ BAM_WB_DSC_AVL_P_RST | \
+ BAM_REG_P_EN | \
+ BAM_PSM_P_HD_DATA | \
+ BAM_AU_ACCUMED | \
+ BAM_CMD_ENABLE)
+
+/* PIPE CTRL */
+#define P_EN BIT(1)
+#define P_DIRECTION BIT(3)
+#define P_SYS_STRM BIT(4)
+#define P_SYS_MODE BIT(5)
+#define P_AUTO_EOB BIT(6)
+#define P_AUTO_EOB_SEL_SHIFT 7
+#define P_AUTO_EOB_SEL_512 (0 << P_AUTO_EOB_SEL_SHIFT)
+#define P_AUTO_EOB_SEL_256 (1 << P_AUTO_EOB_SEL_SHIFT)
+#define P_AUTO_EOB_SEL_128 (2 << P_AUTO_EOB_SEL_SHIFT)
+#define P_AUTO_EOB_SEL_64 (3 << P_AUTO_EOB_SEL_SHIFT)
+#define P_PREFETCH_LIMIT_SHIFT 9
+#define P_PREFETCH_LIMIT_32 (0 << P_PREFETCH_LIMIT_SHIFT)
+#define P_PREFETCH_LIMIT_16 (1 << P_PREFETCH_LIMIT_SHIFT)
+#define P_PREFETCH_LIMIT_4 (2 << P_PREFETCH_LIMIT_SHIFT)
+#define P_WRITE_NWD BIT(11)
+#define P_LOCK_GROUP_SHIFT 16
+#define P_LOCK_GROUP_MASK 0x1F
+
+/* BAM_DESC_CNT_TRSHLD */
+#define CNT_TRSHLD 0xffff
+#define DEFAULT_CNT_THRSHLD 0x4
+
+/* BAM_IRQ_SRCS */
+#define BAM_IRQ BIT(31)
+#define P_IRQ 0x7fffffff
+
+/* BAM_IRQ_SRCS_MSK */
+#define BAM_IRQ_MSK BAM_IRQ
+#define P_IRQ_MSK P_IRQ
+
+/* BAM_IRQ_STTS */
+#define BAM_TIMER_IRQ BIT(4)
+#define BAM_EMPTY_IRQ BIT(3)
+#define BAM_ERROR_IRQ BIT(2)
+#define BAM_HRESP_ERR_IRQ BIT(1)
+
+/* BAM_IRQ_CLR */
+#define BAM_TIMER_CLR BIT(4)
+#define BAM_EMPTY_CLR BIT(3)
+#define BAM_ERROR_CLR BIT(2)
+#define BAM_HRESP_ERR_CLR BIT(1)
+
+/* BAM_IRQ_EN */
+#define BAM_TIMER_EN BIT(4)
+#define BAM_EMPTY_EN BIT(3)
+#define BAM_ERROR_EN BIT(2)
+#define BAM_HRESP_ERR_EN BIT(1)
+
+/* BAM_P_IRQ_EN */
+#define P_PRCSD_DESC_EN BIT(0)
+#define P_TIMER_EN BIT(1)
+#define P_WAKE_EN BIT(2)
+#define P_OUT_OF_DESC_EN BIT(3)
+#define P_ERR_EN BIT(4)
+#define P_TRNSFR_END_EN BIT(5)
+#define P_DEFAULT_IRQS_EN (P_PRCSD_DESC_EN | P_ERR_EN | P_TRNSFR_END_EN)
+
+/* BAM_P_SW_OFSTS */
+#define P_SW_OFSTS_MASK 0xffff
+
+#define BAM_DESC_FIFO_SIZE SZ_32K
+#define MAX_DESCRIPTORS (BAM_DESC_FIFO_SIZE / sizeof(struct bam_desc_hw) - 1)
+#define BAM_MAX_DATA_SIZE (SZ_32K - 8)
+
+struct bam_chan {
+ struct virt_dma_chan vc;
+
+ struct bam_device *bdev;
+
+ /* configuration from device tree */
+ u32 id;
+ u32 ee;
+
+ struct bam_async_desc *curr_txd; /* current running dma */
+
+ /* runtime configuration */
+ struct dma_slave_config slave;
+
+ /* fifo storage */
+ struct bam_desc_hw *fifo_virt;
+ dma_addr_t fifo_phys;
+
+ /* fifo markers */
+ unsigned short head; /* start of active descriptor entries */
+ unsigned short tail; /* end of active descriptor entries */
+
+ unsigned int initialized; /* is the channel hw initialized? */
+ unsigned int paused; /* is the channel paused? */
+
+ struct list_head node;
+};
+
+static inline struct bam_chan *to_bam_chan(struct dma_chan *common)
+{
+ return container_of(common, struct bam_chan, vc.chan);
+}
+
+struct bam_device {
+ void __iomem *regs;
+ struct device *dev;
+ struct dma_device common;
+ struct device_dma_parameters dma_parms;
+ struct bam_chan *channels;
+ u32 num_channels;
+
+ /* execution environment ID, from DT */
+ u32 ee;
+
+ struct clk *bamclk;
+
+ /* dma start transaction tasklet */
+ struct tasklet_struct task;
+};
+
+/**
+ * bam_reset_channel - Reset individual BAM DMA channel
+ * @bchan: bam channel
+ *
+ * This function resets a specific BAM channel
+ */
+static void bam_reset_channel(struct bam_chan *bchan)
+{
+ struct bam_device *bdev = bchan->bdev;
+
+ /* reset channel */
+ writel_relaxed(1, bdev->regs + BAM_P_RST(bchan->id));
+ writel_relaxed(0, bdev->regs + BAM_P_RST(bchan->id));
+
+ /* don't allow reorder of the channel reset */
+ wmb();
+
+ /* make sure hw is initialized when channel is used the first time */
+ bchan->initialized = 0;
+}
+
+/**
+ * bam_chan_init_hw - Initialize channel hardware
+ * @bchan: bam channel
+ *
+ * This function resets and initializes the BAM channel
+ */
+static void bam_chan_init_hw(struct bam_chan *bchan,
+ enum dma_transfer_direction dir)
+{
+ struct bam_device *bdev = bchan->bdev;
+ u32 val;
+
+ /* Reset the channel to clear internal state of the FIFO */
+ bam_reset_channel(bchan);
+
+ /*
+ * write out 8 byte aligned address. We have enough space for this
+ * because we allocated 1 more descriptor (8 bytes) than we can use
+ */
+ writel_relaxed(ALIGN(bchan->fifo_phys, sizeof(struct bam_desc_hw)),
+ bdev->regs + BAM_P_DESC_FIFO_ADDR(bchan->id));
+ writel_relaxed(BAM_DESC_FIFO_SIZE, bdev->regs +
+ BAM_P_FIFO_SIZES(bchan->id));
+
+ /* enable the per pipe interrupts, enable EOT, ERR, and INT irqs */
+ writel_relaxed(P_DEFAULT_IRQS_EN, bdev->regs + BAM_P_IRQ_EN(bchan->id));
+
+ /* unmask the specific pipe and EE combo */
+ val = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee));
+ val |= BIT(bchan->id);
+ writel_relaxed(val, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee));
+
+ /* set fixed direction and mode, then enable channel */
+ val = P_EN | P_SYS_MODE;
+ if (dir == DMA_DEV_TO_MEM)
+ val |= P_DIRECTION;
+
+ /* make sure the other stores occur before enabling channel */
+ wmb();
+ writel_relaxed(val, bdev->regs + BAM_P_CTRL(bchan->id));
+
+ bchan->initialized = 1;
+
+ /* init FIFO pointers */
+ bchan->head = 0;
+ bchan->tail = 0;
+}
+
+/**
+ * bam_alloc_chan - Allocate channel resources for DMA channel.
+ * @chan: specified channel
+ *
+ * This function allocates the FIFO descriptor memory
+ */
+static int bam_alloc_chan(struct dma_chan *chan)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ struct bam_device *bdev = bchan->bdev;
+
+ /* allocate FIFO descriptor space, but only if necessary */
+ if (!bchan->fifo_virt) {
+ bchan->fifo_virt = dma_alloc_writecombine(bdev->dev,
+ BAM_DESC_FIFO_SIZE, &bchan->fifo_phys,
+ GFP_KERNEL);
+
+ if (!bchan->fifo_virt) {
+ dev_err(bdev->dev, "Failed to allocate desc fifo\n");
+ return -ENOMEM;
+ }
+ }
+
+ return BAM_DESC_FIFO_SIZE;
+}
+
+/**
+ * bam_free_chan - Frees dma resources associated with specific channel
+ * @chan: specified channel
+ *
+ * Free the allocated fifo descriptor memory and channel resources
+ *
+ */
+static void bam_free_chan(struct dma_chan *chan)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ struct bam_device *bdev = bchan->bdev;
+ u32 val;
+
+ vchan_free_chan_resources(to_virt_chan(chan));
+
+ if (bchan->curr_txd) {
+ dev_err(bchan->bdev->dev, "Cannot free busy channel\n");
+ return;
+ }
+
+ bam_reset_channel(bchan);
+
+ dma_free_writecombine(bdev->dev, BAM_DESC_FIFO_SIZE, bchan->fifo_virt,
+ bchan->fifo_phys);
+ bchan->fifo_virt = NULL;
+
+ /* mask irq for pipe/channel */
+ val = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee));
+ val &= ~BIT(bchan->id);
+ writel_relaxed(val, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee));
+
+ /* disable irq */
+ writel_relaxed(0, bdev->regs + BAM_P_IRQ_EN(bchan->id));
+}
+
+/**
+ * bam_slave_config - set slave configuration for channel
+ * @chan: dma channel
+ * @cfg: slave configuration
+ *
+ * Sets slave configuration for channel
+ *
+ */
+static void bam_slave_config(struct bam_chan *bchan,
+ struct dma_slave_config *cfg)
+{
+ struct bam_device *bdev = bchan->bdev;
+ u32 maxburst;
+
+ if (bchan->slave.direction == DMA_DEV_TO_MEM)
+ maxburst = bchan->slave.src_maxburst = cfg->src_maxburst;
+ else
+ maxburst = bchan->slave.dst_maxburst = cfg->dst_maxburst;
+
+ /* set desc threshold */
+ writel_relaxed(maxburst, bdev->regs + BAM_DESC_CNT_TRSHLD);
+}
+
+/**
+ * bam_prep_slave_sg - Prep slave sg transaction
+ *
+ * @chan: dma channel
+ * @sgl: scatter gather list
+ * @sg_len: length of sg
+ * @direction: DMA transfer direction
+ * @flags: DMA flags
+ * @context: transfer context (unused)
+ */
+static struct dma_async_tx_descriptor *bam_prep_slave_sg(struct dma_chan *chan,
+ struct scatterlist *sgl, unsigned int sg_len,
+ enum dma_transfer_direction direction, unsigned long flags,
+ void *context)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ struct bam_device *bdev = bchan->bdev;
+ struct bam_async_desc *async_desc;
+ struct scatterlist *sg;
+ u32 i;
+ struct bam_desc_hw *desc;
+
+
+ if (!is_slave_direction(direction)) {
+ dev_err(bdev->dev, "invalid dma direction\n");
+ return NULL;
+ }
+
+
+ /* allocate enough room to accomodate the number of entries */
+ async_desc = kzalloc(sizeof(*async_desc) +
+ (sg_len * sizeof(struct bam_desc_hw)), GFP_NOWAIT);
+
+ if (!async_desc) {
+ dev_err(bdev->dev, "failed to allocate async descriptor\n");
+ goto err_out;
+ }
+
+ async_desc->num_desc = sg_len;
+ async_desc->curr_desc = async_desc->desc;
+ async_desc->dir = direction;
+
+ /* fill in descriptors, align hw descriptor to 8 bytes */
+ desc = async_desc->desc;
+ for_each_sg(sgl, sg, sg_len, i) {
+ if (sg_dma_len(sg) > BAM_MAX_DATA_SIZE) {
+ dev_err(bdev->dev, "segment exceeds max size\n");
+ goto err_out;
+ }
+
+ desc->addr = sg_dma_address(sg);
+ desc->size = sg_dma_len(sg);
+ async_desc->length += sg_dma_len(sg);
+ desc++;
+ }
+
+ return vchan_tx_prep(&bchan->vc, &async_desc->vd, flags);
+
+err_out:
+ kfree(async_desc);
+ return NULL;
+}
+
+/**
+ * bam_dma_terminate_all - terminate all transactions on a channel
+ * @bchan: bam dma channel
+ *
+ * Dequeues and frees all transactions
+ * No callbacks are done
+ *
+ */
+static void bam_dma_terminate_all(struct bam_chan *bchan)
+{
+ unsigned long flag;
+ LIST_HEAD(head);
+
+ /* remove all transactions, including active transaction */
+ spin_lock_irqsave(&bchan->vc.lock, flag);
+ if (bchan->curr_txd) {
+ list_add(&bchan->curr_txd->vd.node, &bchan->vc.desc_issued);
+ bchan->curr_txd = NULL;
+ }
+
+ vchan_get_all_descriptors(&bchan->vc, &head);
+ spin_unlock_irqrestore(&bchan->vc.lock, flag);
+
+ vchan_dma_desc_free_list(&bchan->vc, &head);
+}
+
+/**
+ * bam_control - DMA device control
+ * @chan: dma channel
+ * @cmd: control cmd
+ * @arg: cmd argument
+ *
+ * Perform DMA control command
+ *
+ */
+static int bam_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
+ unsigned long arg)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ struct bam_device *bdev = bchan->bdev;
+ int ret = 0;
+ unsigned long flag;
+
+ switch (cmd) {
+ case DMA_PAUSE:
+ spin_lock_irqsave(&bchan->vc.lock, flag);
+ writel_relaxed(1, bdev->regs + BAM_P_HALT(bchan->id));
+ bchan->paused = 1;
+ spin_unlock_irqrestore(&bchan->vc.lock, flag);
+ break;
+ case DMA_RESUME:
+ spin_lock_irqsave(&bchan->vc.lock, flag);
+ writel_relaxed(0, bdev->regs + BAM_P_HALT(bchan->id));
+ bchan->paused = 0;
+ spin_unlock_irqrestore(&bchan->vc.lock, flag);
+ break;
+ case DMA_TERMINATE_ALL:
+ bam_dma_terminate_all(bchan);
+ break;
+ case DMA_SLAVE_CONFIG:
+ bam_slave_config(bchan, (struct dma_slave_config *)arg);
+ break;
+ default:
+ ret = -ENXIO;
+ break;
+ }
+
+ return ret;
+}
+
+/**
+ * process_channel_irqs - processes the channel interrupts
+ * @bdev: bam controller
+ *
+ * This function processes the channel interrupts
+ *
+ */
+static u32 process_channel_irqs(struct bam_device *bdev)
+{
+ u32 i, srcs, pipe_stts;
+ unsigned long flags;
+ struct bam_async_desc *async_desc;
+
+ srcs = readl_relaxed(bdev->regs + BAM_IRQ_SRCS_EE(bdev->ee));
+
+ /* return early if no pipe/channel interrupts are present */
+ if (!(srcs & P_IRQ))
+ return srcs;
+
+ for (i = 0; i < bdev->num_channels; i++) {
+ struct bam_chan *bchan = &bdev->channels[i];
+ if (srcs & BIT(i)) {
+ /* clear pipe irq */
+ pipe_stts = readl_relaxed(bdev->regs +
+ BAM_P_IRQ_STTS(i));
+
+ writel_relaxed(pipe_stts, bdev->regs +
+ BAM_P_IRQ_CLR(i));
+
+ spin_lock_irqsave(&bchan->vc.lock, flags);
+ async_desc = bchan->curr_txd;
+
+ if (async_desc) {
+ async_desc->num_desc -= async_desc->xfer_len;
+ async_desc->curr_desc += async_desc->xfer_len;
+ bchan->curr_txd = NULL;
+
+ /* manage FIFO */
+ bchan->head += async_desc->xfer_len;
+ bchan->head %= MAX_DESCRIPTORS;
+
+ /*
+ * if complete, process cookie. Otherwise
+ * push back to front of desc_issued so that
+ * it gets restarted by the tasklet
+ */
+ if (!async_desc->num_desc)
+ vchan_cookie_complete(&async_desc->vd);
+ else
+ list_add(&async_desc->vd.node,
+ &bchan->vc.desc_issued);
+ }
+
+ spin_unlock_irqrestore(&bchan->vc.lock, flags);
+ }
+ }
+
+ return srcs;
+}
+
+/**
+ * bam_dma_irq - irq handler for bam controller
+ * @irq: IRQ of interrupt
+ * @data: callback data
+ *
+ * IRQ handler for the bam controller
+ */
+static irqreturn_t bam_dma_irq(int irq, void *data)
+{
+ struct bam_device *bdev = data;
+ u32 clr_mask = 0, srcs = 0;
+
+ srcs |= process_channel_irqs(bdev);
+
+ /* kick off tasklet to start next dma transfer */
+ if (srcs & P_IRQ)
+ tasklet_schedule(&bdev->task);
+
+ if (srcs & BAM_IRQ)
+ clr_mask = readl_relaxed(bdev->regs + BAM_IRQ_STTS);
+
+ /* don't allow reorder of the various accesses to the BAM registers */
+ mb();
+
+ writel_relaxed(clr_mask, bdev->regs + BAM_IRQ_CLR);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * bam_tx_status - returns status of transaction
+ * @chan: dma channel
+ * @cookie: transaction cookie
+ * @txstate: DMA transaction state
+ *
+ * Return status of dma transaction
+ */
+static enum dma_status bam_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
+ struct dma_tx_state *txstate)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ struct virt_dma_desc *vd;
+ int ret;
+ size_t residue = 0;
+ unsigned int i;
+ unsigned long flags;
+
+ ret = dma_cookie_status(chan, cookie, txstate);
+ if (ret == DMA_COMPLETE)
+ return ret;
+
+ if (!txstate)
+ return bchan->paused ? DMA_PAUSED : ret;
+
+ spin_lock_irqsave(&bchan->vc.lock, flags);
+ vd = vchan_find_desc(&bchan->vc, cookie);
+ if (vd)
+ residue = container_of(vd, struct bam_async_desc, vd)->length;
+ else if (bchan->curr_txd && bchan->curr_txd->vd.tx.cookie == cookie)
+ for (i = 0; i < bchan->curr_txd->num_desc; i++)
+ residue += bchan->curr_txd->curr_desc[i].size;
+
+ spin_unlock_irqrestore(&bchan->vc.lock, flags);
+
+ dma_set_residue(txstate, residue);
+
+ if (ret == DMA_IN_PROGRESS && bchan->paused)
+ ret = DMA_PAUSED;
+
+ return ret;
+}
+
+/**
+ * bam_start_dma - start next transaction
+ * @bchan - bam dma channel
+ *
+ * Note: must hold bam dma channel vc.lock
+ */
+static void bam_start_dma(struct bam_chan *bchan)
+{
+ struct virt_dma_desc *vd = vchan_next_desc(&bchan->vc);
+ struct bam_device *bdev = bchan->bdev;
+ struct bam_async_desc *async_desc;
+ struct bam_desc_hw *desc;
+ struct bam_desc_hw *fifo = PTR_ALIGN(bchan->fifo_virt,
+ sizeof(struct bam_desc_hw));
+
+ if (!vd)
+ return;
+
+ list_del(&vd->node);
+
+ async_desc = container_of(vd, struct bam_async_desc, vd);
+ bchan->curr_txd = async_desc;
+
+ /* on first use, initialize the channel hardware */
+ if (!bchan->initialized)
+ bam_chan_init_hw(bchan, async_desc->dir);
+
+
+ desc = bchan->curr_txd->curr_desc;
+
+ if (async_desc->num_desc > MAX_DESCRIPTORS)
+ async_desc->xfer_len = MAX_DESCRIPTORS;
+ else
+ async_desc->xfer_len = async_desc->num_desc;
+
+ /* set INT on last descriptor */
+ desc[async_desc->xfer_len - 1].flags |= DESC_FLAG_INT;
+
+ if (bchan->tail + async_desc->xfer_len > MAX_DESCRIPTORS) {
+ u32 partial = MAX_DESCRIPTORS - bchan->tail;
+
+ memcpy(&fifo[bchan->tail], desc,
+ partial * sizeof(struct bam_desc_hw));
+ memcpy(fifo, &desc[partial], (async_desc->xfer_len - partial) *
+ sizeof(struct bam_desc_hw));
+ } else {
+ memcpy(&fifo[bchan->tail], desc,
+ async_desc->xfer_len * sizeof(struct bam_desc_hw));
+ }
+
+ bchan->tail += async_desc->xfer_len;
+ bchan->tail %= MAX_DESCRIPTORS;
+
+ /* ensure descriptor writes and dma start not reordered */
+ wmb();
+ writel_relaxed(bchan->tail * sizeof(struct bam_desc_hw),
+ bdev->regs + BAM_P_EVNT_REG(bchan->id));
+}
+
+/**
+ * dma_tasklet - DMA IRQ tasklet
+ * @data: tasklet argument (bam controller structure)
+ *
+ * Sets up next DMA operation and then processes all completed transactions
+ */
+static void dma_tasklet(unsigned long data)
+{
+ struct bam_device *bdev = (struct bam_device *)data;
+ struct bam_chan *bchan;
+ unsigned long flags;
+ unsigned int i;
+
+ /* go through the channels and kick off transactions */
+ for (i = 0; i < bdev->num_channels; i++) {
+ bchan = &bdev->channels[i];
+ spin_lock_irqsave(&bchan->vc.lock, flags);
+
+ if (!list_empty(&bchan->vc.desc_issued) && !bchan->curr_txd)
+ bam_start_dma(bchan);
+ spin_unlock_irqrestore(&bchan->vc.lock, flags);
+ }
+}
+
+/**
+ * bam_issue_pending - starts pending transactions
+ * @chan: dma channel
+ *
+ * Calls tasklet directly which in turn starts any pending transactions
+ */
+static void bam_issue_pending(struct dma_chan *chan)
+{
+ struct bam_chan *bchan = to_bam_chan(chan);
+ unsigned long flags;
+
+ spin_lock_irqsave(&bchan->vc.lock, flags);
+
+ /* if work pending and idle, start a transaction */
+ if (vchan_issue_pending(&bchan->vc) && !bchan->curr_txd)
+ bam_start_dma(bchan);
+
+ spin_unlock_irqrestore(&bchan->vc.lock, flags);
+}
+
+/**
+ * bam_dma_free_desc - free descriptor memory
+ * @vd: virtual descriptor
+ *
+ */
+static void bam_dma_free_desc(struct virt_dma_desc *vd)
+{
+ struct bam_async_desc *async_desc = container_of(vd,
+ struct bam_async_desc, vd);
+
+ kfree(async_desc);
+}
+
+static struct dma_chan *bam_dma_xlate(struct of_phandle_args *dma_spec,
+ struct of_dma *of)
+{
+ struct bam_device *bdev = container_of(of->of_dma_data,
+ struct bam_device, common);
+ unsigned int request;
+
+ if (dma_spec->args_count != 1)
+ return NULL;
+
+ request = dma_spec->args[0];
+ if (request >= bdev->num_channels)
+ return NULL;
+
+ return dma_get_slave_channel(&(bdev->channels[request].vc.chan));
+}
+
+/**
+ * bam_init
+ * @bdev: bam device
+ *
+ * Initialization helper for global bam registers
+ */
+static int bam_init(struct bam_device *bdev)
+{
+ u32 val;
+
+ /* read revision and configuration information */
+ val = readl_relaxed(bdev->regs + BAM_REVISION) & NUM_EES_MASK;
+
+ /* check that configured EE is within range */
+ if (bdev->ee >= val)
+ return -EINVAL;
+
+ val = readl_relaxed(bdev->regs + BAM_NUM_PIPES);
+ bdev->num_channels = val & BAM_NUM_PIPES_MASK;
+
+ /* s/w reset bam */
+ /* after reset all pipes are disabled and idle */
+ val = readl_relaxed(bdev->regs + BAM_CTRL);
+ val |= BAM_SW_RST;
+ writel_relaxed(val, bdev->regs + BAM_CTRL);
+ val &= ~BAM_SW_RST;
+ writel_relaxed(val, bdev->regs + BAM_CTRL);
+
+ /* make sure previous stores are visible before enabling BAM */
+ wmb();
+
+ /* enable bam */
+ val |= BAM_EN;
+ writel_relaxed(val, bdev->regs + BAM_CTRL);
+
+ /* set descriptor threshhold, start with 4 bytes */
+ writel_relaxed(DEFAULT_CNT_THRSHLD, bdev->regs + BAM_DESC_CNT_TRSHLD);
+
+ /* Enable default set of h/w workarounds, ie all except BAM_FULL_PIPE */
+ writel_relaxed(BAM_CNFG_BITS_DEFAULT, bdev->regs + BAM_CNFG_BITS);
+
+ /* enable irqs for errors */
+ writel_relaxed(BAM_ERROR_EN | BAM_HRESP_ERR_EN,
+ bdev->regs + BAM_IRQ_EN);
+
+ return 0;
+}
+
+static void bam_channel_init(struct bam_device *bdev, struct bam_chan *bchan,
+ u32 index)
+{
+ bchan->id = index;
+ bchan->bdev = bdev;
+
+ vchan_init(&bchan->vc, &bdev->common);
+ bchan->vc.desc_free = bam_dma_free_desc;
+}
+
+static int bam_dma_probe(struct platform_device *pdev)
+{
+ struct bam_device *bdev;
+ struct resource *iores;
+ int ret, i, irq;
+
+ bdev = devm_kzalloc(&pdev->dev, sizeof(*bdev), GFP_KERNEL);
+ if (!bdev)
+ return -ENOMEM;
+
+ bdev->dev = &pdev->dev;
+
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ bdev->regs = devm_ioremap_resource(&pdev->dev, iores);
+ if (IS_ERR(bdev->regs))
+ return PTR_ERR(bdev->regs);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ bdev->bamclk = devm_clk_get(bdev->dev, "bam_clk");
+ if (IS_ERR(bdev->bamclk))
+ return PTR_ERR(bdev->bamclk);
+
+ ret = clk_prepare_enable(bdev->bamclk);
+ if (ret) {
+ dev_err(bdev->dev, "failed to prepare/enable clock");
+ return ret;
+ }
+
+ ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &bdev->ee);
+ if (ret) {
+ dev_err(bdev->dev, "EE unspecified\n");
+ return ret;
+ }
+
+ ret = bam_init(bdev);
+ if (ret)
+ return ret;
+
+ tasklet_init(&bdev->task, dma_tasklet, (unsigned long)bdev);
+
+ bdev->channels = devm_kcalloc(bdev->dev, bdev->num_channels,
+ sizeof(*bdev->channels), GFP_KERNEL);
+
+ if (!bdev->channels) {
+ ret = -ENOMEM;
+ goto err_disable_clk;
+ }
+
+ /* allocate and initialize channels */
+ INIT_LIST_HEAD(&bdev->common.channels);
+
+ for (i = 0; i < bdev->num_channels; i++)
+ bam_channel_init(bdev, &bdev->channels[i], i);
+
+ ret = devm_request_irq(bdev->dev, irq, bam_dma_irq, IRQF_TRIGGER_HIGH,
+ "bam_dma", bdev);
+ if (ret)
+ goto err_disable_clk;
+
+ /* set max dma segment size */
+ bdev->common.dev = bdev->dev;
+ bdev->common.dev->dma_parms = &bdev->dma_parms;
+ ret = dma_set_max_seg_size(bdev->common.dev, BAM_MAX_DATA_SIZE);
+ if (ret) {
+ dev_err(bdev->dev, "cannot set maximum segment size\n");
+ goto err_disable_clk;
+ }
+
+ platform_set_drvdata(pdev, bdev);
+
+ /* set capabilities */
+ dma_cap_zero(bdev->common.cap_mask);
+ dma_cap_set(DMA_SLAVE, bdev->common.cap_mask);
+
+ /* initialize dmaengine apis */
+ bdev->common.device_alloc_chan_resources = bam_alloc_chan;
+ bdev->common.device_free_chan_resources = bam_free_chan;
+ bdev->common.device_prep_slave_sg = bam_prep_slave_sg;
+ bdev->common.device_control = bam_control;
+ bdev->common.device_issue_pending = bam_issue_pending;
+ bdev->common.device_tx_status = bam_tx_status;
+ bdev->common.dev = bdev->dev;
+
+ ret = dma_async_device_register(&bdev->common);
+ if (ret) {
+ dev_err(bdev->dev, "failed to register dma async device\n");
+ goto err_disable_clk;
+ }
+
+ ret = of_dma_controller_register(pdev->dev.of_node, bam_dma_xlate,
+ &bdev->common);
+ if (ret)
+ goto err_unregister_dma;
+
+ return 0;
+
+err_unregister_dma:
+ dma_async_device_unregister(&bdev->common);
+err_disable_clk:
+ clk_disable_unprepare(bdev->bamclk);
+ return ret;
+}
+
+static int bam_dma_remove(struct platform_device *pdev)
+{
+ struct bam_device *bdev = platform_get_drvdata(pdev);
+ u32 i;
+
+ dma_async_device_unregister(&bdev->common);
+ of_dma_controller_free(pdev->dev.of_node);
+
+ /* mask all interrupts for this execution environment */
+ writel_relaxed(0, bdev->regs + BAM_IRQ_SRCS_MSK_EE(bdev->ee));
+
+ for (i = 0; i < bdev->num_channels; i++) {
+ bam_dma_terminate_all(&bdev->channels[i]);
+ tasklet_kill(&bdev->channels[i].vc.task);
+ }
+
+ tasklet_kill(&bdev->task);
+
+ clk_disable_unprepare(bdev->bamclk);
+
+ return 0;
+}
+
+static const struct of_device_id bam_of_match[] = {
+ { .compatible = "qcom,bam-v1.4.0", },
+ { .compatible = "qcom,bam-v1.4.1", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, bam_of_match);
+
+static struct platform_driver bam_dma_driver = {
+ .probe = bam_dma_probe,
+ .remove = bam_dma_remove,
+ .driver = {
+ .name = "bam-dma-engine",
+ .owner = THIS_MODULE,
+ .of_match_table = bam_of_match,
+ },
+};
+
+module_platform_driver(bam_dma_driver);
+
+MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>");
+MODULE_DESCRIPTION("QCOM BAM DMA engine driver");
+MODULE_LICENSE("GPL v2");
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply related
* [Patch v4 0/2] Add Qualcomm BAM dmaengine driver
From: Andy Gross @ 2014-02-03 23:04 UTC (permalink / raw)
To: Vinod Koul, Dan Williams, dmaengine
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-arm-msm,
Andy Gross
This patch set introduces the dmaengine driver for the Qualcomm Bus Access
Manager (BAM) DMA controller present on MSM 8x74 devices. A number of the
on-chip devices have their own BAM DMA controller and use it to move data
between system memory and peripherals or between two peripherals.
The initial version of this driver will only support slave DMA operations
between system memory and peripherals.
Changes from v3:
- Remove unused bam_channel_dir.
- Remove incorrect write to BAM_IRQ_SRCS_EE (read only).
- Remove dma direction from DT binding and revise driver to use
direction from prep_slave_sg.
- Remove unnecessary channel reset from channel_init. This could affect
channels controlled from other execution environments.
- Change terminate_all to also take care of the current active
descriptor.
- Rework .remove function to correctly mask interrupts and clean up
resources and tasklets.
Changes from v2:
- Corrected Kconfig dependencies
- Moved execution environment ID to controller DT binding. The EE is
a global setting across all of the channels on the controller.
- Combined header into source file.
- Corrected copyright date.
- Moved channel hardware initialization to occur when channel is used
for the first time.
- Converted dma_alloc_coherent to dma_alloc_writecombine
- Removed unecessary reset of channel from the dma terminate_all
- Corrected usage of EE in irq handler and channel configuration
functions.
- Changed resource functions inside probe to use correct APIs.
- Removed dma filter function and modified dma_xlate to use
dma_get_slave_channel API
- Fixed various nit comments
Changes from v1:
- Converted driver to use virt-dma
- Reworked probe function per review comments
- tx_status function now computes and returns residuals
- Removed proprietary slave config. Removed associated include file.
- Renamed files to reflect vendor name instead of specific device
- Converted to use (readl|writel)_relaxed w/ appropriate barriers
- Removed unions in favor of standard types.
Andy Gross (2):
dmaengine: add Qualcomm BAM dma driver
dmaengine: qcom_bam_dma: Add device tree binding
.../devicetree/bindings/dma/qcom_bam_dma.txt | 48 +
drivers/dma/Kconfig | 9 +
drivers/dma/Makefile | 1 +
drivers/dma/qcom_bam_dma.c | 1059 ++++++++++++++++++++
4 files changed, 1117 insertions(+)
create mode 100644 Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
create mode 100644 drivers/dma/qcom_bam_dma.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
hosted by The Linux Foundation
^ permalink raw reply
* Re: [PATCH] arm64: Add architecture support for PCI
From: Andrew Murray @ 2014-02-03 22:34 UTC (permalink / raw)
To: Liviu Dudau
Cc: devicetree@vger.kernel.org, linaro-kernel, Arnd Bergmann,
linux-pci, Will Deacon, LKML, Catalin Marinas, Bjorn Helgaas,
LAKML
In-Reply-To: <1391453028-23191-2-git-send-email-Liviu.Dudau@arm.com>
On 3 February 2014 18:43, Liviu Dudau <Liviu.Dudau@arm.com> wrote:
> diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h
> index 4cc813e..ce5bad2 100644
> --- a/arch/arm64/include/asm/io.h
> +++ b/arch/arm64/include/asm/io.h
> @@ -120,9 +120,13 @@ static inline u64 __raw_readq(const volatile void __iomem *addr)
> /*
> * I/O port access primitives.
> */
> +#define arch_has_dev_port() (0)
> #define IO_SPACE_LIMIT 0xffff
> #define PCI_IOBASE ((void __iomem *)(MODULES_VADDR - SZ_2M))
>
> +#define ioport_map(port, nr) (PCI_IOBASE + ((port) & IO_SPACE_LIMIT))
> +#define ioport_unmap(addr)
I'm not sure that this will work. The in[bwl], out[bwl] macros in
arch/arm64/include/asm/io.h already add the PCI_IOBASE offset.
Instead of these two #defines, why not just enforce that
GENERIC_PCI_IOMAP is enabled? Or at least wrap these defines with 'if
(!config_enabled(CONFIG_GENERIC_PCI_IOMAP))' or similar.
> +
> static inline u8 inb(unsigned long addr)
> {
> return readb(addr + PCI_IOBASE);
Andrew Murray
^ permalink raw reply
* [PATCH v3 7/7] arm: zynq: Add support for cpufreq
From: Soren Brinkmann @ 2014-02-03 22:34 UTC (permalink / raw)
To: Thomas Gleixner, Daniel Lezcano, Michal Simek
Cc: linux-kernel, linux-arm-kernel, Sören Brinkmann, Rob Herring,
Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King,
devicetree
In-Reply-To: <1391466877-28908-1-git-send-email-soren.brinkmann@xilinx.com>
The generic cpufreq-cpu0 driver can scale the CPU frequency on Zynq
SOCs. Add the required platform device to the BSP and appropriate
OPPs to the dts.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
---
v3:
- change lowest frequency to 222223 (F_max / 3)
---
arch/arm/boot/dts/zynq-7000.dtsi | 6 ++++++
arch/arm/mach-zynq/Kconfig | 2 ++
arch/arm/mach-zynq/common.c | 3 +++
3 files changed, 11 insertions(+)
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index 8b67b19392ec..789d0bacc110 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -24,6 +24,12 @@
device_type = "cpu";
reg = <0>;
clocks = <&clkc 3>;
+ operating-points = <
+ /* kHz uV */
+ 666667 1000000
+ 333334 1000000
+ 222223 1000000
+ >;
};
cpu@1 {
diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig
index f84fab14f0b7..f03e75bd0b2b 100644
--- a/arch/arm/mach-zynq/Kconfig
+++ b/arch/arm/mach-zynq/Kconfig
@@ -2,6 +2,8 @@ config ARCH_ZYNQ
bool "Xilinx Zynq ARM Cortex A9 Platform" if ARCH_MULTI_V7
select ARM_AMBA
select ARM_GIC
+ select ARCH_HAS_CPUFREQ
+ select ARCH_HAS_OPP
select COMMON_CLK
select CPU_V7
select GENERIC_CLOCKEVENTS
diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c
index 1db2a5ca9ab8..644468151c04 100644
--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c
@@ -51,6 +51,8 @@ static struct platform_device zynq_cpuidle_device = {
*/
static void __init zynq_init_machine(void)
{
+ struct platform_device_info devinfo = { .name = "cpufreq-cpu0", };
+
/*
* 64KB way size, 8-way associativity, parity disabled
*/
@@ -59,6 +61,7 @@ static void __init zynq_init_machine(void)
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
platform_device_register(&zynq_cpuidle_device);
+ platform_device_register_full(&devinfo);
}
static void __init zynq_timer_init(void)
--
1.8.5.3
^ permalink raw reply related
* Re: [PATCH] pci: Add support for creating a generic host_bridge from device tree
From: Liviu Dudau @ 2014-02-03 22:17 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linux-pci, Bjorn Helgaas, Catalin Marinas, Will Deacon, LKML,
devicetree@vger.kernel.org, LAKML, linaro-kernel
In-Reply-To: <3523674.i9iUPinOAk@wuerfel>
On Mon, Feb 03, 2014 at 07:31:31PM +0000, Arnd Bergmann wrote:
> On Monday 03 February 2014 19:06:49 Liviu Dudau wrote:
> > On Mon, Feb 03, 2014 at 06:46:10PM +0000, Arnd Bergmann wrote:
> > > On Monday 03 February 2014 18:33:48 Liviu Dudau wrote:
> > > > +/**
> > > > + * pci_host_bridge_of_get_ranges - Parse PCI host bridge resources from DT
> > > > + * @dev: device node of the host bridge having the range property
> > > > + * @resources: list where the range of resources will be added after DT parsing
> > > > + *
> > > > + * This function will parse the "ranges" property of a PCI host bridge device
> > > > + * node and setup the resource mapping based on its content. It is expected
> > > > + * that the property conforms with the Power ePAPR document.
> > > > + *
> > > > + * Each architecture will then apply their filtering based on the limitations
> > > > + * of each platform. One general restriction seems to be the number of IO space
> > > > + * ranges, the PCI framework makes intensive use of struct resource management,
> > > > + * and for IORESOURCE_IO types they can only be requested if they are contained
> > > > + * within the global ioport_resource, so that should be limited to one IO space
> > > > + * range.
> > >
> > > Actually we have quite a different set of restrictions around I/O space on ARM32
> > > at the moment: Each host bridge can have its own 64KB range in an arbitrary
> > > location on MMIO space, and the total must not exceed 2MB of I/O space.
> >
> > And that is why the filtering is not (yet) imposed in the generic code. But once
> > you use pci_request_region, that will call request_region which will check
> > against ioport_resource as parent for the requested resource. That should fail
> > if is is not in the correct range, so I don't know how arm arch code manages
> > multiple IO ranges.
>
> Let's try to come up with nomenclature so we can talk about this better
>
> The ioport_resource is in "logical I/O space", which is a Linux fiction,
> it goes from 0 to IO_SPACE_LIMIT (2MB on ARM) and is mapped into "virtual
> I/O space", which start at (void __iomem *)PCI_IO_VIRT_BASE.
>
> Each PCI domain can have its own "bus I/O aperture", which is typically
> between 0x1000 and 0xffff and reflects the address that is used in PCI
> transactions and in BARs.
Actually, the bus I/O aperture can start from 0x0000 if you are talking about
PCI bus addresses.
> The aperture here reflects the subset of the
> 4GB bus I/O space that is actually mapped into a CPU visible "physical
> I/O aperture" using an inbound mapping of the host bridge. The physical
> I/O aperture in turn gets mapped to the virtual I/O space using
> pci_ioremap_io.
Agree.
> The difference between a bus I/O address and a logical
> I/O address is stored in the io_offset.
Not exactly. If that would be true that means that for an I/O range that
start at bus I/O address zero but physical I/O apperture starts at
0x40000000 the io_offset is zero. For me, the io_offset should be 0x40000000.
Let me see if I can summarise this correctly, using only CPU addresses:
0x0000 - IO_SPACE_LIMIT <- logical I/O address
0xPPPPPPPP - 0xPPPPPPPP+IO_SIZE <- physical address for PCI I/O space
0xVVVVVVVV - 0xVVVVVVVV+IO_SPACE_LIMIT <- virtual address for I/O
The io_offset then is 0xPPPPPPPP - logical I/O address. At least that is
the intent of the io_offset variable that I introduced in pci_host_bridge.
The bus I/O address is generated by the host bridge, I think we can ignore
it here as it tends to confuse the message.
>
> So much for basic definitions. When a device driver calls pci_request_region,
> the port number it sees is the bus I/O port number adjusted using the
> io_offset to turn it into a logical I/O port number, which should
> always be within the host bridge window, which in turn is a subset
> of the ioport_resource.
My understanding is that device drivers all user port numbers that are logical
I/O numbers, so no io_offset needs to be applied here. It is only when one
wants to access the port, that the translation happens. First, inb or outb
will add the PCI_IO_VIRT_BASE to generate the virtual address, the MMU will
then convert that address to physical address and the host bridge will
then translate the physical address into bus address.
>
> > > > +static int pci_host_bridge_of_get_ranges(struct device_node *dev,
> > > > + struct list_head *resources)
> > > > +{
> > > > + struct resource *res;
> > > > + struct of_pci_range range;
> > > > + struct of_pci_range_parser parser;
> > > > + int err;
> > > > +
> > > > + pr_info("PCI host bridge %s ranges:\n", dev->full_name);
> > > > +
> > > > + /* Check for ranges property */
> > > > + err = of_pci_range_parser_init(&parser, dev);
> > > > + if (err)
> > > > + return err;
> > > > +
> > > > + pr_debug("Parsing ranges property...\n");
> > > > + for_each_of_pci_range(&parser, &range) {
> > > > + /* Read next ranges element */
> > > > + pr_debug("pci_space: 0x%08x pci_addr:0x%016llx ",
> > > > + range.pci_space, range.pci_addr);
> > > > + pr_debug("cpu_addr:0x%016llx size:0x%016llx\n",
> > > > + range.cpu_addr, range.size);
> > > > +
> > > > + /* If we failed translation or got a zero-sized region
> > > > + * (some FW try to feed us with non sensical zero sized regions
> > > > + * such as power3 which look like some kind of attempt
> > > > + * at exposing the VGA memory hole) then skip this range
> > > > + */
> > > > + if (range.cpu_addr == OF_BAD_ADDR || range.size == 0)
> > > > + continue;
> > > > +
> > > > + res = kzalloc(sizeof(struct resource), GFP_KERNEL);
> > > > + if (!res) {
> > > > + err = -ENOMEM;
> > > > + goto bridge_ranges_nomem;
> > > > + }
> > > > +
> > > > + of_pci_range_to_resource(&range, dev, res);
> > > > +
> > > > + pci_add_resource_offset(resources, res,
> > > > + range.cpu_addr - range.pci_addr);
> > > > + }
> > >
> > > I believe of_pci_range_to_resource() will return the MMIO aperture for the
> > > I/O space window here, which is not what you are supposed to pass into
> > > pci_add_resource_offset.
> >
> > And that is why the code in probe.c has been added to deal with that. It is
> > too early to do the adjustments here as all we have is the list of resources
> > and that might get culled by the architecture fixup code. Remembering the
> > io_offset will happen once the pci_host_bridge gets created, and the resources
> > are then adjusted.
>
> So you want to register an incorrect I/O resource first and then
> have it fixed up later, rather than registering the correct
> one from the start as everyone else?
The incorrect I/O resource is added to a temporary list of resources, it has not
been attached yet to the list of windows in the bridge. What gets added is the
I/O resource as described if it would be an ordinary resource.
>
> > > > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> > > > index 6e34498..16febae 100644
> > > > --- a/drivers/pci/probe.c
> > > > +++ b/drivers/pci/probe.c
> > > > @@ -1787,6 +1787,17 @@ struct pci_bus *pci_create_root_bus(struct device *parent, int bus,
> > > > list_for_each_entry_safe(window, n, resources, list) {
> > > > list_move_tail(&window->list, &bridge->windows);
> > > > res = window->res;
> > > > + /*
> > > > + * IO resources are stored in the kernel with a CPU start
> > > > + * address of zero. Adjust the data accordingly and remember
> > > > + * the offset
> > > > + */
> > > > + if (resource_type(res) == IORESOURCE_IO) {
> > > > + bridge->io_offset = res->start;
> > > > + res->end -= res->start;
> > > > + window->offset -= res->start;
> > > > + res->start = 0;
> > > > + }
Here, we correct for the fact that IORESOURCE_IO is not a normal resource, because Linux wants
a logical I/O as start and end address, not the physical CPU address. We adjust to that and
remember the offset.
> > > > offset = window->offset;
> > > > if (res->flags & IORESOURCE_BUS)
> > >
> > > Won't this break all existing host bridges?
> >
> > I am not sure. I believe not, due to what I've explained earlier, but you might be right.
> >
> > The adjustment happens before the resource is added to the host bridge windows and translates
> > it from MMIO range into IO range.
>
> AFAICT, the resource_type of the resource you register above should be
> IORESOURCE_MEM, so you are not actually matching it here.
No, all resources are added here. For IORESOURCE_IO we do an adjustment.
Best regards,
Liviu
>
> Arnd
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
>
--
====================
| I would like to |
| fix the world, |
| but they're not |
| giving me the |
\ source code! /
---------------
¯\_(ツ)_/¯
^ permalink raw reply
* Re: [RFC PATCH V3 1/4] pci: APM X-Gene PCIe controller driver
From: Jason Gunthorpe @ 2014-02-03 22:15 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Tanmay Inamdar, Bjorn Helgaas, Grant Likely, Rob Herring,
Catalin Marinas, Rob Landley, linux-pci@vger.kernel.org,
devicetree@vger.kernel.org, linux-arm-kernel, linux-doc,
linux-kernel, patches, Jon Masters, Liviu Dudau
In-Reply-To: <4985267.LnsktRmabM@wuerfel>
On Mon, Feb 03, 2014 at 09:12:32PM +0100, Arnd Bergmann wrote:
> Are you sure that is true for the root bridge as well? I don't
> remember the details, but I though that for the host bridge,
> we don't actually look at the BARs at all.
That is right, but this isn't a host bridge device, it is a PCI-PCI
bridge with root complex registers. The root complex bridge is not the
same as the host bridge.
Unfortunately the implementation is non-conforming. :(
Jason
^ permalink raw reply
* Re: [PATCH v5 14/14] ARM: sun7i: dts: Add ahci / sata support
From: Hans de Goede @ 2014-02-03 22:10 UTC (permalink / raw)
To: Maxime Ripard
Cc: Tejun Heo, Oliver Schinagl, Richard Zhu, Roger Quadros,
linux-ide-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
In-Reply-To: <20140131134638.GH2950@lukather>
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi,
On 01/31/2014 02:46 PM, Maxime Ripard wrote:
> On Wed, Jan 22, 2014 at 08:04:49PM +0100, Hans de Goede wrote:
>> This patch adds sunxi sata support to A20 boards that have such a connector. Some boards also feature a regulator via a GPIO and support for this is also added.
>>
>> Signed-off-by: Olliver Schinagl <oliver-dxLnbx3+1qmEVqv0pETR8A@public.gmane.org> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> --- arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 6 ++++++ arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 20 ++++++++++++++++++++ arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 6 ++++++ arch/arm/boot/dts/sun7i-a20.dtsi | 8 ++++++++ 4 files changed, 40 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index 48777cd..1cab521 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -13,6 +13,7 @@
>>
>> /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-ahci-reg.dtsi"
>>
>> / { model = "Cubietech Cubieboard2"; @@ -28,6 +29,11 @@ status = "okay"; };
>>
>> + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + pinctrl@01c20800 { mmc0_cd_pin_cubieboard2: mmc0_cd_pin@0 { allwinner,pins = "PH1"; diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts index 2684f27..1247ea1 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -13,6 +13,7 @@
>>
>> /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-ahci-reg.dtsi"
>>
>> / { model = "Cubietech Cubietruck"; @@ -28,6 +29,11 @@ status = "okay"; };
>>
>> + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + pinctrl@01c20800 { mmc0_cd_pin_cubietruck: mmc0_cd_pin@0 { allwinner,pins = "PH1"; @@ -36,6 +42,13 @@ allwinner,pull = <0>; };
>>
>> + ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 { + allwinner,pins = "PH12"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + led_pins_cubietruck: led_pins@0 { allwinner,pins = "PH7", "PH11", "PH20", "PH21"; allwinner,function = "gpio_out"; @@ -84,4 +97,11 @@ gpios = <&pio 7 7 0>; }; }; + + regulators { + reg_ahci_5v: ahci-5v { + pinctrl-0 = <&ahci_pwr_pin_cubietruck>; + gpio = <&pio 7 12 0>; + }; + }; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index
>> bf6f6c8..f135886 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -13,6 +13,7 @@
>>
>> /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-ahci-reg.dtsi"
>>
>> / { model = "Olimex A20-Olinuxino Micro"; @@ -37,6 +38,11 @@ status = "okay"; };
>>
>> + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + pinctrl@01c20800 { mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 { allwinner,pins = "PH1"; diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index c9c123a..0657bad 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -347,6 +347,14 @@ status = "disabled"; };
>>
>> + ahci: sata@01c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <0 56 1>;
>
> This is supposed to be a level triggered interrupt, not an edge triggered one.
Good catch, will fix for the next version.
Regards,
Hans
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Using GnuPG with Thunderbird - http://www.enigmail.net/
iEYEARECAAYFAlLwE+sACgkQF3VEtJrzE/tKaACgmEEVd28Oubd7hEy5chG3/XM9
0x0AmwctbAFVFC9OCBaNZix8cX3d/CAI
=otiv
-----END PGP SIGNATURE-----
--
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/groups/opt_out.
^ permalink raw reply
* Re: [PATCH RFC v4 00/10] ahci: library-ise ahci_platform, add sunxi driver and cleanup imx driver
From: Hans de Goede @ 2014-02-03 22:08 UTC (permalink / raw)
To: Rob Herring
Cc: Tejun Heo, devicetree, linux-ide-u79uwXL29TY76Z2rM5mHXA,
Oliver Schinagl, Richard Zhu, linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
Maxime Ripard,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Roger Quadros
In-Reply-To: <CAL_JsqKnus+9rgLAQ990eD-1F6-2G-SuqYuPkmc+Tw6QP1CT4g-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
Hi,
On 02/03/2014 05:31 PM, Rob Herring wrote:
> On Mon, Jan 20, 2014 at 10:44 AM, Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
>> Hi All,
>>
>> Here is v4 of my patchset for adding ahci-sunxi support. It has grown quite
>> a bit since I've been going for a more generic approach this time and I've
>> also cleaned up the ahci-imx driver to use the same generic approach.
>
> I don't know if you missed it or just don't intend to refactor all
> AHCI drivers, but the highbank driver could benefit from this as well.
I don't intend to refactor all of them, esp. not the ones for which I don't
have hardware to test.
As they say: patches welcome :)
Regards,
Hans
^ permalink raw reply
* Re: [PATCH v5 00/14] ahci: library-ise ahci_platform, add sunxi driver and cleanup imx driver
From: Hans de Goede @ 2014-02-03 22:07 UTC (permalink / raw)
To: Tejun Heo
Cc: Oliver Schinagl, Maxime Ripard, Richard Zhu, Roger Quadros,
linux-ide-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, devicetree,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
In-Reply-To: <20140203160936.GC30250-Gd/HAXX7CRxy/B6EtB590w@public.gmane.org>
Hi,
On 02/03/2014 05:09 PM, Tejun Heo wrote:
> Hello,
>
> On Wed, Jan 22, 2014 at 08:04:35PM +0100, Hans de Goede wrote:
>> Here is v4 of my patchset for adding ahci-sunxi support. It has grown quite
>> a bit since I've been going for a more generic approach this time and I've
>> also cleaned up the ahci-imx driver to use the same generic approach.
>
> On top of which tree were these patches generated? They don't apply
> to 3.14-rc1.
They are on top of 3.13, I'll rebase them, address Maxime's review of
the dts bits and send a new version sometime during the next couple of days.
Thanks,
Hans
^ permalink raw reply
* Re: [PATCH] spi: rspi: fix build error when CONFIG_OF is not set
From: Rob Herring @ 2014-02-03 21:45 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Shimoda, Yoshihiro, Grant Likely, Rob Herring, Mark Brown,
linux-spi@vger.kernel.org, SH-Linux, devicetree@vger.kernel.org,
Linux Kernel Development
In-Reply-To: <alpine.DEB.2.02.1402030939520.25794@ayla.of.borg>
On Mon, Feb 3, 2014 at 2:47 AM, Geert Uytterhoeven <geert@linux-m68k.org> wrote:
> Hi Shimoda-san,
>
> On Mon, 3 Feb 2014, Shimoda, Yoshihiro wrote:
>> This patch fixes an issue that the following build error happens when
>> the CONFIG_OF is not set:
>>
>> drivers/spi/spi-rspi.c: In function 'rspi_probe':
>> drivers/spi/spi-rspi.c:1203:26: error: 'rspi_of_match' undeclared (first use in this function)
>>
>> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
>> ---
>> This patch is based on the latest origin/topic/rspi branch in the spi.git.
>>
>> drivers/spi/spi-rspi.c | 1 +
>> 1 files changed, 1 insertions(+), 0 deletions(-)
>>
>> diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c
>> index 34ad4bc..e5cfc3d 100644
>> --- a/drivers/spi/spi-rspi.c
>> +++ b/drivers/spi/spi-rspi.c
>> @@ -1164,6 +1164,7 @@ static int rspi_parse_dt(struct device *dev, struct spi_master *master)
>> return 0;
>> }
>> #else
>> +#define rspi_of_match NULL
>> static inline int rspi_parse_dt(struct device *dev, struct spi_master *master)
>> {
>> return -EINVAL;
>> --
>> 1.7.1
>
> Thanks, obviously I missed that of_match_device() still uses the ID table
> parameter if CONFIG_OF=n :-(
>
> Below I have two alternative solutions:
> 1. Uses rspi_of_match() to nullify the ID table pointer, like is done in
> the platform_driver structure,
> 2. Fixes it at the OF subsystem level, by nullifying the ID table pointer
> inside of_match_device().
>
> If 2 is accepted, drivers don't have to care about this anymore.
>
> What do you think?
I'll apply the 2nd one.
Rob
^ permalink raw reply
* Re: [PATCH] arm64: Add architecture support for PCI
From: Liviu Dudau @ 2014-02-03 21:36 UTC (permalink / raw)
To: Arnd Bergmann
Cc: linaro-kernel@lists.linaro.org, devicetree@vger.kernel.org,
linux-pci, LKML, Catalin Marinas, Bjorn Helgaas, LAKML
In-Reply-To: <3808209.DeG1VobanZ@wuerfel>
On Mon, Feb 03, 2014 at 08:05:56PM +0000, Arnd Bergmann wrote:
> On Monday 03 February 2014 19:18:38 Liviu Dudau wrote:
> > On Mon, Feb 03, 2014 at 06:58:56PM +0000, Arnd Bergmann wrote:
> > > On Monday 03 February 2014 18:43:48 Liviu Dudau wrote:
> > > > diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h
> > > > index 4cc813e..ce5bad2 100644
> > > > --- a/arch/arm64/include/asm/io.h
> > > > +++ b/arch/arm64/include/asm/io.h
> > > > @@ -120,9 +120,13 @@ static inline u64 __raw_readq(const volatile void __iomem *addr)
> > > > /*
> > > > * I/O port access primitives.
> > > > */
> > > > +#define arch_has_dev_port() (0)
> > >
> > > Why not?
> >
> > Maybe I got it the wrong way around, but the comment in include/linux/io.h says:
> >
> > /*
> > * Some systems do not have legacy ISA devices.
> > * /dev/port is not a valid interface on these systems.
> > * So for those archs, <asm/io.h> should define the following symbol.
> > */
> >
> > So ... defining it should mean no legacy ISA devices, right?
>
> I would read that comment as referring to systems that don't have
> any I/O space. If you have PCI, you can by definition have ISA
> compatible devices behind a bridge. A typical example would be
> a VGA card that supports the 03c0-03df port range.
But if you have PCI and don't want to support ISA do you have /dev/port? I guess yes.
In that case ISA support is irrelevant here. Will update the value when I send v2.
>
> > >
> > > > #define IO_SPACE_LIMIT 0xffff
> > >
> > > You probably want to increase this a bit, to allow multiple host bridges
> > > to have their own I/O space.
> >
> > OK, but to what size?
>
> 2 MB was a compromise on arm32 to allow up to 32 PCI host bridges but not
> take up too much virtual space. On arm64 it should be at least as big.
> Could be more than that, although I don't see a reason why it should be,
> unless we expect to see systems with tons of host bridges, or buses
> that exceed 64KB of I/O space.
I will increase the size to 2MB for v2.
>
> > > > +#define ioport_map(port, nr) (PCI_IOBASE + ((port) & IO_SPACE_LIMIT))
> > > > +#define ioport_unmap(addr)
> > >
> > > inline functions?
> >
> > Will do, thanks!
>
> I suppose you can actually use the generic implementation from
> asm-generic/io.h, and fix it by using the definition you have
> above, since it's currently broken.
Not exactly broken, but it makes the assumption that your IO space starts at
physical address zero and you have not remapped it. It does guard the
definition with #ifndef CONFIG_GENERIC_IOMAP after all, so it does not
expect to be generic :)
>
> > > > diff --git a/arch/arm64/include/asm/pci.h b/arch/arm64/include/asm/pci.h
> > > > new file mode 100644
> > > > index 0000000..dd084a3
> > > > --- /dev/null
> > > > +++ b/arch/arm64/include/asm/pci.h
> > > > @@ -0,0 +1,35 @@
> > > > +#ifndef __ASM_PCI_H
> > > > +#define __ASM_PCI_H
> > > > +#ifdef __KERNEL__
> > > > +
> > > > +#include <linux/types.h>
> > > > +#include <linux/slab.h>
> > > > +#include <linux/dma-mapping.h>
> > > > +
> > > > +#include <asm/io.h>
> > > > +#include <asm-generic/pci-bridge.h>
> > > > +#include <asm-generic/pci-dma-compat.h>
> > > > +
> > > > +#define PCIBIOS_MIN_IO 0
> > > > +#define PCIBIOS_MIN_MEM 0
> > >
> > > PCIBIOS_MIN_IO is normally set to 0x1000, to stay out of the ISA range.
> >
> > :) No ISA support! (Die ISA, die!!)
>
> If only it were that easy.
Lets try! :)
I wonder how many active devices that have an ISA slot are still supported
by mainline kernel.
I will update PCIBIOS_MIN_xxxx to match arch/arm for v2.
>
> > > > diff --git a/arch/arm64/kernel/pci.c b/arch/arm64/kernel/pci.c
> > > > new file mode 100644
> > > > index 0000000..7b652cf
> > > > --- /dev/null
> > > > +++ b/arch/arm64/kernel/pci.c
> > > > @@ -0,0 +1,112 @@
> > >
> > > None of this looks really arm64 specific, nor should it be. I think
> > > we should try a little harder to move this as a default implementation
> > > into common code, even if we start out by having all architectures
> > > override it.
> >
> > Agree. This is the RFC version. I didn't dare to post a patch with fixes
> > for all architectures. :)
>
> No need to change the other architectures. You can make it opt-in for
> now and just put the code into a common location.
>
> An interesting question however is what the transition plan is to
> have the code shared between arm32 and arm64: We will certainly need
> to share at least the dw-pcie and the generic SBSA compliant pci
> implementation.
My vote would be for updating the host controllers to the new API and
to offer the CONFIG option to choose between arch APIs. The alternative
is to use the existing API to wrap the generic implementation.
My main concern with the existing API is the requirement to have a subsys_initcall
in your host bridge or mach code, due to the way the initialisation is done (you
need the DT code to probe your driver, but you cannot start the scanning of the
PCI bus until the arch code is initialised, so it gets deferred via
subsys_initcall when it calls pci_common_init). I bet that if one tries to
instantiate a Tegra PCI host bridge controller on a Marvell platform things will
break pretty quickly (random example here).
>
> > > > +int pci_ioremap_io(unsigned int offset, phys_addr_t phys_addr)
> > > > +{
> > > > + BUG_ON(offset + SZ_64K - 1 > IO_SPACE_LIMIT);
> > > > +
> > > > + return ioremap_page_range((unsigned long)PCI_IOBASE + offset,
> > > > + (unsigned long)PCI_IOBASE + offset + SZ_64K,
> > > > + phys_addr,
> > > > + __pgprot(PROT_DEVICE_nGnRE));
> > > > +}
> > >
> > > Not sure if we want to treat this one as architecture specific though.
> > > It certainly won't be portable to x86, but it could be shared with
> > > a couple of others. We may also want to redesign the interface.
> > > I've been thinking we could make this function allocate space in the
> > > Linux virtual I/O space aperture, and pass two resources into it
> > > (physical I/O aperture and bus I/O range), and get the actual
> > > io_offset as the return value, or a negative error number.
> >
> > Not sure I completely follow your idea.
>
> Something like this (coded in mail client, don't try to compile):
>
> #define IO_SPACE_PAGES (IO_SPACE_LIMIT + 1) / PAGE_SIZE)
> static DECLARE_BITMAP(pci_iospace, IO_SPACE_PAGES);
> unsigned long pci_ioremap_io(const struct resource *bus, const struct resource phys)
> {
> unsigned long start, len, virt_start;
> int error;
>
> /* use logical address == bus address if possible */
> start = bus->start / PAGE_SIZE;
> if (start > IO_SPACE_LIMIT / PAGE_SIZE)
> start = 0;
>
> /*
> * try finding free space for the whole size first,
> * fall back to 64K if not available
> */
> len = min(resource_size(bus), resource_size(phys);
> start = bitmap_find_next_zero_area(pci_iospace, IO_SPACE_PAGES,
> start, len / PAGE_SIZE, 0);
> if (start == IO_SPACE_PAGES && len > SZ_64K)
> len = SZ_64K;
> start = 0;
> start = bitmap_find_next_zero_area(pci_iospace, IO_SPACE_PAGES,
> start, len / PAGE_SIZE, 0);
> }
>
> /* no 64K area found */
> if (start == IO_SPACE_PAGES)
> return -ENOMEM;
>
> /* ioremap physical aperture to virtual aperture */
> virt_start = start * PAGE_SIZE + (unsigned long)PCI_IOBASE;
> error = ioremap_page_range(virt_start, virt_start + len,
> phys->start, __pgprot(PROT_DEVICE_nGnRE));
> if (error)
> return error;
>
> bitmap_set(start, len / PAGE_SIZE);
>
> /* return io_offset */
> return start * PAGE_SIZE - bus->start;
> }
> EXPORT_SYMBOL_GPL(pci_ioremap_io);
>
> Arnd
>
I see. I need to think how this will change the existing code. Current users of pci_ioremap_io
ask for multiples of SZ_64K offsets regardless of the actual need.
Best regards,
Liviu
--
====================
| I would like to |
| fix the world, |
| but they're not |
| giving me the |
\ source code! /
---------------
¯\_(ツ)_/¯
^ permalink raw reply
* [PATCH v6 8/8] ARM: brcmstb: dts: add a reference DTS for Broadcom 7445
From: Marc Carino @ 2014-02-03 21:30 UTC (permalink / raw)
To: Christian Daudt, Arnd Bergmann, Olof Johansson
Cc: Florian Fainelli, Matt Porter, Russell King, linux-arm-kernel,
linux-kernel, devicetree, Marc Carino
In-Reply-To: <1391463041-15241-1-git-send-email-marc.ceeeee@gmail.com>
Add a sample DTS which will allow bootup of a board populated
with the BCM7445 chip.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
arch/arm/boot/dts/bcm7445.dts | 111 +++++++++++++++++++++++++++++++++++++++++
1 files changed, 111 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boot/dts/bcm7445.dts
diff --git a/arch/arm/boot/dts/bcm7445.dts b/arch/arm/boot/dts/bcm7445.dts
new file mode 100644
index 0000000..ffa3305
--- /dev/null
+++ b/arch/arm/boot/dts/bcm7445.dts
@@ -0,0 +1,111 @@
+/dts-v1/;
+/include/ "skeleton.dtsi"
+
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ model = "Broadcom STB (bcm7445)";
+ compatible = "brcm,bcm7445", "brcm,brcmstb";
+ interrupt-parent = <&gic>;
+
+ chosen {};
+
+ memory {
+ device_type = "memory";
+ reg = <0x00 0x00000000 0x00 0x40000000>,
+ <0x00 0x40000000 0x00 0x40000000>,
+ <0x00 0x80000000 0x00 0x40000000>;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "brcm,brahma-b15";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu@1 {
+ compatible = "brcm,brahma-b15";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu@2 {
+ compatible = "brcm,brahma-b15";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu@3 {
+ compatible = "brcm,brahma-b15";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ gic: interrupt-controller@ffd00000 {
+ compatible = "brcm,brahma-b15-gic", "arm,cortex-a15-gic";
+ reg = <0x00 0xffd01000 0x00 0x1000>,
+ <0x00 0xffd02000 0x00 0x2000>,
+ <0x00 0xffd04000 0x00 0x2000>,
+ <0x00 0xffd06000 0x00 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <1 13 0xf08>,
+ <1 14 0xf08>,
+ <1 11 0xf08>,
+ <1 10 0xf08>;
+ };
+
+ rdb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0 0x00 0xf0000000 0x1000000>;
+
+ serial@406b00 {
+ compatible = "ns16550a";
+ reg = <0x406b00 0x20>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <0 75 0x4>;
+ clock-frequency = <0x4d3f640>;
+ };
+
+ sun_top_ctrl: syscon@404000 {
+ compatible = "brcm,bcm7445-sun-top-ctrl",
+ "syscon";
+ reg = <0x404000 0x51c>;
+ };
+
+ hif_cpubiuctrl: syscon@3e2400 {
+ compatible = "brcm,bcm7445-hif-cpubiuctrl",
+ "syscon";
+ reg = <0x3e2400 0x5b4>;
+ };
+
+ hif_continuation: syscon@452000 {
+ compatible = "brcm,bcm7445-hif-continuation",
+ "syscon";
+ reg = <0x452000 0x100>;
+ };
+ };
+
+ smpboot {
+ compatible = "brcm,brcmstb-smpboot";
+ syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>;
+ syscon-cont = <&hif_continuation>;
+ };
+
+ reboot {
+ compatible = "brcm,brcmstb-reboot";
+ syscon = <&sun_top_ctrl 0x304 0x308>;
+ };
+};
--
1.7.1
^ permalink raw reply related
* [PATCH v6 7/8] ARM: brcmstb: gic: add compatible string for Broadcom Brahma15
From: Marc Carino @ 2014-02-03 21:30 UTC (permalink / raw)
To: Christian Daudt, Arnd Bergmann, Olof Johansson
Cc: Florian Fainelli, Matt Porter, Russell King, linux-arm-kernel,
linux-kernel, devicetree, Marc Carino
In-Reply-To: <1391463041-15241-1-git-send-email-marc.ceeeee@gmail.com>
Document the Broadcom Brahma B15 GIC implementation as compatible
with the ARM GIC standard.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
Documentation/devicetree/bindings/arm/gic.txt | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
index bae0d87..d1f0b98 100644
--- a/Documentation/devicetree/bindings/arm/gic.txt
+++ b/Documentation/devicetree/bindings/arm/gic.txt
@@ -16,6 +16,7 @@ Main node required properties:
"arm,cortex-a9-gic"
"arm,cortex-a7-gic"
"arm,arm11mp-gic"
+ "brcm,brahma-b15-gic"
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Specifies the number of cells needed to encode an
interrupt source. The type shall be a <u32> and the value shall be 3.
--
1.7.1
^ permalink raw reply related
* [PATCH v6 6/8] ARM: brcmstb: add misc. DT bindings for brcmstb
From: Marc Carino @ 2014-02-03 21:30 UTC (permalink / raw)
To: Christian Daudt, Arnd Bergmann, Olof Johansson
Cc: Florian Fainelli, Matt Porter, Russell King, linux-arm-kernel,
linux-kernel, devicetree, Marc Carino
In-Reply-To: <1391463041-15241-1-git-send-email-marc.ceeeee@gmail.com>
Document the bindings that the Broadcom STB platform needs
for proper bootup.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
.../devicetree/bindings/arm/brcm-brcmstb.txt | 95 ++++++++++++++++++++
1 files changed, 95 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/brcm-brcmstb.txt
diff --git a/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt
new file mode 100644
index 0000000..3c436cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/brcm-brcmstb.txt
@@ -0,0 +1,95 @@
+ARM Broadcom STB platforms Device Tree Bindings
+-----------------------------------------------
+Boards with Broadcom Brahma15 ARM-based BCMxxxx (generally BCM7xxx variants)
+SoC shall have the following DT organization:
+
+Required root node properties:
+ - compatible: "brcm,bcm<chip_id>", "brcm,brcmstb"
+
+example:
+/ {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ model = "Broadcom STB (bcm7445)";
+ compatible = "brcm,bcm7445", "brcm,brcmstb";
+
+Further, syscon nodes that map platform-specific registers used for general
+system control is required:
+
+ - compatible: "brcm,bcm<chip_id>-sun-top-ctrl", "syscon"
+ - compatible: "brcm,bcm<chip_id>-hif-cpubiuctrl", "syscon"
+ - compatible: "brcm,bcm<chip_id>-hif-continuation", "syscon"
+
+example:
+ rdb {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ ranges = <0 0x00 0xf0000000 0x1000000>;
+
+ sun_top_ctrl: syscon@404000 {
+ compatible = "brcm,bcm7445-sun-top-ctrl", "syscon";
+ reg = <0x404000 0x51c>;
+ };
+
+ hif_cpubiuctrl: syscon@3e2400 {
+ compatible = "brcm,bcm7445-hif-cpubiuctrl", "syscon";
+ reg = <0x3e2400 0x5b4>;
+ };
+
+ hif_continuation: syscon@452000 {
+ compatible = "brcm,bcm7445-hif-continuation", "syscon";
+ reg = <0x452000 0x100>;
+ };
+ };
+
+Lastly, nodes that allow for support of SMP initialization and reboot are
+required:
+
+smpboot
+-------
+Required properties:
+
+ - compatible
+ The string "brcm,brcmstb-smpboot".
+
+ - syscon-cpu
+ A phandle / integer array property which lets the BSP know the location
+ of certain CPU power-on registers.
+
+ The layout of the property is as follows:
+ o a phandle to the "hif_cpubiuctrl" syscon node
+ o offset to the base CPU power zone register
+ o offset to the base CPU reset register
+
+ - syscon-cont
+ A phandle pointing to the syscon node which describes the CPU boot
+ continuation registers.
+ o a phandle to the "hif_continuation" syscon node
+
+example:
+ smpboot {
+ compatible = "brcm,brcmstb-smpboot";
+ syscon-cpu = <&hif_cpubiuctrl 0x88 0x178>;
+ syscon-cont = <&hif_continuation>;
+ };
+
+reboot
+-------
+Required properties
+
+ - compatible
+ The string property "brcm,brcmstb-reboot".
+
+ - syscon
+ A phandle / integer array that points to the syscon node which describes
+ the general system reset registers.
+ o a phandle to "sun_top_ctrl"
+ o offset to the "reset source enable" register
+ o offset to the "software master reset" register
+
+example:
+ reboot {
+ compatible = "brcm,brcmstb-reboot";
+ syscon = <&sun_top_ctrl 0x304 0x308>;
+ };
--
1.7.1
^ permalink raw reply related
* [PATCH v6 5/8] ARM: brcmstb: add CPU binding for Broadcom Brahma15
From: Marc Carino @ 2014-02-03 21:30 UTC (permalink / raw)
To: Christian Daudt, Arnd Bergmann, Olof Johansson
Cc: Florian Fainelli, Matt Porter, Russell King, linux-arm-kernel,
linux-kernel, devicetree, Marc Carino
In-Reply-To: <1391463041-15241-1-git-send-email-marc.ceeeee@gmail.com>
Add the Broadcom Brahma B15 CPU to the DT CPU binding list.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
---
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index 9130435..0cd1e25 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -163,6 +163,7 @@ nodes to be present and contain the properties described below.
"arm,cortex-r4"
"arm,cortex-r5"
"arm,cortex-r7"
+ "brcm,brahma-b15"
"faraday,fa526"
"intel,sa110"
"intel,sa1100"
--
1.7.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox