* [PATCH 13/14] ARM: dts: armada-375: Fixup memory DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
memory has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375-db.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 2da6300d184d..2018ccbfd058 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -58,7 +58,7 @@
stdout-path = "serial0:115200n8";
};
- memory {
+ memory@0 {
device_type = "memory";
reg = <0x00000000 0x40000000>; /* 1 GB */
};
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 12/14] ARM: dts: armada-375: Remove skeleton.dtsi
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 6fa7500df893..74824a1817b4 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -45,7 +45,6 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/phy/phy.h>
@@ -53,6 +52,9 @@
#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
model = "Marvell Armada 375 family SoC";
compatible = "marvell,armada375";
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 11/14] ARM: dts: armada-375: Fixup internal-regs DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
internal-regs has a ranges property so the unit name should contain an
address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index d7781554687d..6fa7500df893 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -165,7 +165,7 @@
status = "disabled";
};
- internal-regs {
+ internal-regs@f1000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 10/14] ARM: dts: armada-375: Fixup soc DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
soc has a ranges property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375-db.dts | 2 +-
arch/arm/boot/dts/armada-375.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index b33a674088ed..2da6300d184d 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -63,7 +63,7 @@
reg = <0x00000000 0x40000000>; /* 1 GB */
};
- soc {
+ soc@f1000000 {
ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 84ef033aeeed..d7781554687d 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -101,7 +101,7 @@
interrupts-extended = <&mpic 3>;
};
- soc {
+ soc@f1000000 {
compatible = "marvell,armada375-mbus", "simple-bus";
#address-cells = <2>;
#size-cells = <1>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 09/14] ARM: dts: armada-375: Fixup pinctrl DT warnings
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
pinctrl has a ranges property, so the unit name should contain an
address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index a157b62e810e..84ef033aeeed 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -307,7 +307,7 @@
status = "disabled";
};
- pinctrl: pinctrl {
+ pinctrl: pinctrl@18000 {
compatible = "marvell,mv88f6720-pinctrl";
reg = <0x18000 0x24>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 08/14] ARM: dts: armada-375: Fixup pcie DT warnings
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
PCIe has a ranges property, so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 700d80fe0d85..a157b62e810e 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -580,7 +580,7 @@
};
};
- pciec: pcie-controller@82000000@ {
+ pciec: pcie-controller@82000000 {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 07/14] ARM: dts: armada-375: Fixup pcie DT warnings
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
PCIe has a range property, so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index c832ebb40ac4..700d80fe0d85 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -580,7 +580,7 @@
};
};
- pciec: pcie-controller {
+ pciec: pcie-controller@82000000@ {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 06/14] ARM: dts: armada-375: Fixup sa-ram DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
sa-sram which is a mmio-sram has a reg property so the unit name should
contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 390575b2142c..c832ebb40ac4 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -635,7 +635,7 @@
};
- crypto_sram0: sa-sram0 {
+ crypto_sram0: sa-sram0@0 {
compatible = "mmio-sram";
reg = <MBUS_ID(0x09, 0x09) 0 0x800>;
clocks = <&gateclk 30>;
@@ -644,7 +644,7 @@
ranges = <0 MBUS_ID(0x09, 0x09) 0 0x800>;
};
- crypto_sram1: sa-sram1 {
+ crypto_sram1: sa-sram1@0 {
compatible = "mmio-sram";
reg = <MBUS_ID(0x09, 0x05) 0 0x800>;
clocks = <&gateclk 31>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 05/14] ARM: dts: armada-375: Fixup devbus DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
devbus has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index e4150c34f128..390575b2142c 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -115,7 +115,7 @@
reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
};
- devbus_bootcs: devbus-bootcs {
+ devbus_bootcs: devbus-bootcs@10400 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
@@ -125,7 +125,7 @@
status = "disabled";
};
- devbus_cs0: devbus-cs0 {
+ devbus_cs0: devbus-cs0@10408 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
@@ -135,7 +135,7 @@
status = "disabled";
};
- devbus_cs1: devbus-cs1 {
+ devbus_cs1: devbus-cs1@10410 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
@@ -145,7 +145,7 @@
status = "disabled";
};
- devbus_cs2: devbus-cs2 {
+ devbus_cs2: devbus-cs2@10418 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
@@ -155,7 +155,7 @@
status = "disabled";
};
- devbus_cs3: devbus-cs3 {
+ devbus_cs3: devbus-cs3@10420 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 04/14] ARM: dts: armada-375: Fixup bootrom DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
bootrom has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 97b663d83fb6..e4150c34f128 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -110,7 +110,7 @@
pcie-mem-aperture = <0xe0000000 0x8000000>;
pcie-io-aperture = <0xe8000000 0x100000>;
- bootrom {
+ bootrom@0 {
compatible = "marvell,bootrom";
reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
};
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 03/14] ARM: dts: armada-375: Fixup mdio DT warning
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
MDIO has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index e016ff3ed970..97b663d83fb6 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -203,7 +203,7 @@
<0xc100 0x100>;
};
- mdio: mdio {
+ mdio: mdio@c0054 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "marvell,orion-mdio";
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 02/14] ARM: dts: armada-375: Use the node labels
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Use the node label when possible. As a result it flattens the device tree
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375-db.dts | 269 ++++++++++++++++++------------------
1 file changed, 136 insertions(+), 133 deletions(-)
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index cded5f0a262d..b33a674088ed 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -69,138 +69,141 @@
MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>;
- internal-regs {
- spi@10600 {
- pinctrl-0 = <&spi0_pins>;
- pinctrl-names = "default";
- /*
- * SPI conflicts with NAND, so we disable it
- * here, and select NAND as the enabled device
- * by default.
- */
- status = "disabled";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
-
- i2c@11000 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
- };
-
- i2c@11100 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
- };
-
- serial@12000 {
- status = "okay";
- };
-
- pinctrl {
- sdio_st_pins: sdio-st-pins {
- marvell,pins = "mpp44", "mpp45";
- marvell,function = "gpio";
- };
- };
-
- sata@a0000 {
- status = "okay";
- nr-ports = <2>;
- };
-
- nand: nand@d0000 {
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
- status = "okay";
- num-cs = <1>;
- marvell,nand-keep-config;
- marvell,nand-enable-arbiter;
- nand-on-flash-bbt;
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
-
- partition@0 {
- label = "U-Boot";
- reg = <0 0x800000>;
- };
- partition@800000 {
- label = "Linux";
- reg = <0x800000 0x800000>;
- };
- partition@1000000 {
- label = "Filesystem";
- reg = <0x1000000 0x3f000000>;
- };
- };
-
- usb@54000 {
- status = "okay";
- };
-
- usb3@58000 {
- status = "okay";
- };
-
- mvsdio@d4000 {
- pinctrl-0 = <&sdio_pins &sdio_st_pins>;
- pinctrl-names = "default";
- status = "okay";
- cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
- };
-
- mdio {
- phy0: ethernet-phy@0 {
- reg = <0>;
- };
-
- phy3: ethernet-phy@3 {
- reg = <3>;
- };
- };
-
- ethernet@f0000 {
- status = "okay";
-
- eth0@c4000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
-
- eth1@c5000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "gmii";
- };
- };
- };
-
- pcie-controller {
- status = "okay";
- /*
- * The two PCIe units are accessible through
- * standard PCIe slots on the board.
- */
- pcie@1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- pcie@2,0 {
- /* Port 1, Lane 0 */
- status = "okay";
- };
- };
};
};
+&pciec {
+ status = "okay";
+};
+
+/*
+ * The two PCIe units are accessible through
+ * standard PCIe slots on the board.
+ */
+&pcie0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+};
+
+&pcie1 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+};
+
+
+&spi0 {
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+
+ /*
+ * SPI conflicts with NAND, so we disable it here, and
+ * select NAND as the enabled device by default.
+ */
+
+ status = "disabled";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "default";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&pinctrl {
+ sdio_st_pins: sdio-st-pins {
+ marvell,pins = "mpp44", "mpp45";
+ marvell,function = "gpio";
+ };
+};
+
+&sata {
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0 0x800000>;
+ };
+ partition@800000 {
+ label = "Linux";
+ reg = <0x800000 0x800000>;
+ };
+ partition@1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+ };
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&sdio {
+ pinctrl-0 = <&sdio_pins &sdio_st_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+};
+
+&mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ };
+};
+
+ðernet {
+ status = "okay";
+};
+
+
+ð0 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+ð1 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "gmii";
+};
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 01/14] ARM: dts: armada-375: Add node labels
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161110001000.10619-1-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
As it was previously done for kirkwood and for aramda 370/XP, this adds
missing node labels to Armada 375 and SoC specific nodes to allow to
reference them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
arch/arm/boot/dts/armada-375.dtsi | 62 +++++++++++++++++++--------------------
1 file changed, 31 insertions(+), 31 deletions(-)
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 45fa92f9cf5c..e016ff3ed970 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -84,12 +84,12 @@
#size-cells = <0>;
enable-method = "marvell,armada-375-smp";
- cpu@0 {
+ cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0>;
};
- cpu@1 {
+ cpu1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <1>;
@@ -115,7 +115,7 @@
reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
};
- devbus-bootcs {
+ devbus_bootcs: devbus-bootcs {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
@@ -125,7 +125,7 @@
status = "disabled";
};
- devbus-cs0 {
+ devbus_cs0: devbus-cs0 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
@@ -135,7 +135,7 @@
status = "disabled";
};
- devbus-cs1 {
+ devbus_cs1: devbus-cs1 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
@@ -145,7 +145,7 @@
status = "disabled";
};
- devbus-cs2 {
+ devbus_cs2: devbus-cs2 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
@@ -155,7 +155,7 @@
status = "disabled";
};
- devbus-cs3 {
+ devbus_cs3: devbus-cs3 {
compatible = "marvell,mvebu-devbus";
reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
@@ -182,12 +182,12 @@
prefetch-data = <1>;
};
- scu@c000 {
+ scu: scu@c000 {
compatible = "arm,cortex-a9-scu";
reg = <0xc000 0x58>;
};
- timer@c600 {
+ timer0: timer@c600 {
compatible = "arm,cortex-a9-twd-timer";
reg = <0xc600 0x20>;
interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
@@ -203,7 +203,7 @@
<0xc100 0x100>;
};
- mdio {
+ mdio: mdio {
#address-cells = <1>;
#size-cells = <0>;
compatible = "marvell,orion-mdio";
@@ -212,7 +212,7 @@
};
/* Network controller */
- ethernet@f0000 {
+ ethernet: ethernet@f0000 {
compatible = "marvell,armada-375-pp2";
reg = <0xf0000 0xa000>, /* Packet Processor regs */
<0xc0000 0x3060>, /* LMS regs */
@@ -235,7 +235,7 @@
};
};
- rtc@10300 {
+ rtc: rtc@10300 {
compatible = "marvell,orion-rtc";
reg = <0x10300 0x20>;
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
@@ -307,7 +307,7 @@
status = "disabled";
};
- pinctrl {
+ pinctrl: pinctrl {
compatible = "marvell,mv88f6720-pinctrl";
reg = <0x18000 0x24>;
@@ -382,7 +382,7 @@
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
};
- system-controller@18200 {
+ systemc: system-controller@18200 {
compatible = "marvell,armada-375-system-controller";
reg = <0x18200 0x100>;
};
@@ -415,7 +415,7 @@
interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
};
- timer@20300 {
+ timer1: timer@20300 {
compatible = "marvell,armada-375-timer", "marvell,armada-370-timer";
reg = <0x20300 0x30>, <0x21040 0x30>;
interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
@@ -428,24 +428,24 @@
clock-names = "nbclk", "fixed";
};
- watchdog@20300 {
+ watchdog: watchdog@20300 {
compatible = "marvell,armada-375-wdt";
reg = <0x20300 0x34>, <0x20704 0x4>, <0x18254 0x4>;
clocks = <&coreclk 0>, <&refclk>;
clock-names = "nbclk", "fixed";
};
- cpurst@20800 {
+ cpurst: cpurst@20800 {
compatible = "marvell,armada-370-cpu-reset";
reg = <0x20800 0x10>;
};
- coherency-fabric@21010 {
+ coherencyfab: coherency-fabric@21010 {
compatible = "marvell,armada-375-coherency-fabric";
reg = <0x21010 0x1c>;
};
- usb@50000 {
+ usb0: usb@50000 {
compatible = "marvell,orion-ehci";
reg = <0x50000 0x500>;
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
@@ -455,7 +455,7 @@
status = "disabled";
};
- usb@54000 {
+ usb1: usb@54000 {
compatible = "marvell,orion-ehci";
reg = <0x54000 0x500>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
@@ -463,7 +463,7 @@
status = "disabled";
};
- usb3@58000 {
+ usb2: usb3@58000 {
compatible = "marvell,armada-375-xhci";
reg = <0x58000 0x20000>,<0x5b880 0x80>;
interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
@@ -473,7 +473,7 @@
status = "disabled";
};
- xor@60800 {
+ xor0: xor@60800 {
compatible = "marvell,orion-xor";
reg = <0x60800 0x100
0x60A00 0x100>;
@@ -493,7 +493,7 @@
};
};
- xor@60900 {
+ xor1: xor@60900 {
compatible = "marvell,orion-xor";
reg = <0x60900 0x100
0x60b00 0x100>;
@@ -513,7 +513,7 @@
};
};
- crypto@90000 {
+ cesa: crypto@90000 {
compatible = "marvell,armada-375-crypto";
reg = <0x90000 0x10000>;
reg-names = "regs";
@@ -528,7 +528,7 @@
marvell,crypto-sram-size = <0x800>;
};
- sata@a0000 {
+ sata: sata@a0000 {
compatible = "marvell,armada-370-sata";
reg = <0xa0000 0x5000>;
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
@@ -537,7 +537,7 @@
status = "disabled";
};
- nand@d0000 {
+ nand: nand@d0000 {
compatible = "marvell,armada370-nand";
reg = <0xd0000 0x54>;
#address-cells = <1>;
@@ -547,7 +547,7 @@
status = "disabled";
};
- mvsdio@d4000 {
+ sdio: mvsdio@d4000 {
compatible = "marvell,orion-sdio";
reg = <0xd4000 0x200>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
@@ -559,7 +559,7 @@
status = "disabled";
};
- thermal@e8078 {
+ thermal: thermal@e8078 {
compatible = "marvell,armada375-thermal";
reg = <0xe8078 0x4>, <0xe807c 0x8>;
status = "okay";
@@ -580,7 +580,7 @@
};
};
- pcie-controller {
+ pciec: pcie-controller {
compatible = "marvell,armada-370-pcie";
status = "disabled";
device_type = "pci";
@@ -599,7 +599,7 @@
0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 1 MEM */
0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 1 IO */>;
- pcie@1,0 {
+ pcie0: pcie@1,0 {
device_type = "pci";
assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
reg = <0x0800 0 0 0 0>;
@@ -616,7 +616,7 @@
status = "disabled";
};
- pcie@2,0 {
+ pcie1: pcie@2,0 {
device_type = "pci";
assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
reg = <0x1000 0 0 0 0>;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 00/14] Various Armada 375 DT warning fixup
From: Gregory CLEMENT @ 2016-11-10 0:09 UTC (permalink / raw)
To: Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, Gregory CLEMENT
Cc: Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi,
This series follow the work done on the Armada 370/XP:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/466006.html
This patchset fixes up various warning from the DT compiler when using
the flag W=1 with make. This time there is no remaining warnings.
As there was only one board associated to Armada 375 its dts have been
fully converted to use the labels.
Gregory
Gregory CLEMENT (14):
ARM: dts: armada-375: Add node labels
ARM: dts: armada-375: Use the node labels
ARM: dts: armada-375: Fixup mdio DT warning
ARM: dts: armada-375: Fixup bootrom DT warning
ARM: dts: armada-375: Fixup devbus DT warning
ARM: dts: armada-375: Fixup sa-ram DT warning
ARM: dts: armada-375: Fixup pcie DT warnings
ARM: dts: armada-375: Fixup pcie DT warnings
ARM: dts: armada-375: Fixup pinctrl DT warnings
ARM: dts: armada-375: Fixup soc DT warning
ARM: dts: armada-375: Fixup internal-regs DT warning
ARM: dts: armada-375: Remove skeleton.dtsi
ARM: dts: armada-375: Fixup memory DT warning
ARM: dts: armada-375: Fixup ethernet child DT warning
arch/arm/boot/dts/armada-375-db.dts | 273 ++++++++++++++++++------------------
arch/arm/boot/dts/armada-375.dtsi | 80 +++++------
2 files changed, 179 insertions(+), 174 deletions(-)
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v2 4/6] pinctrl: aspeed: Read and write bits in LPCHC and GFX controllers
From: Andrew Jeffery @ 2016-11-09 23:50 UTC (permalink / raw)
To: Rob Herring
Cc: Lee Jones, Linus Walleij, Joel Stanley, Mark Rutland, linux-gpio,
linux-arm-kernel, linux-kernel, devicetree
In-Reply-To: <20161109182632.etsvezgfu7nhtl55@rob-hp-laptop>
[-- Attachment #1: Type: text/plain, Size: 5698 bytes --]
On Wed, 2016-11-09 at 12:26 -0600, Rob Herring wrote:
> On Thu, Nov 03, 2016 at 01:07:59AM +1030, Andrew Jeffery wrote:
> > The System Control Unit IP block in the Aspeed SoCs is typically where
> > the pinmux configuration is found, but not always. A number of pins
> > depend on state in one of LPC Host Control (LPCHC) or SoC Display
> > Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
> > means to adjust these as necessary.
> >
> > We use syscon to cast a regmap over the GFX and LPCHCR blocks, which is
> > used as an arbitration layer between the relevant driver and the pinctrl
> > subsystem. The regmaps are then exposed to the SoC-specific pinctrl
> > drivers by phandles in the devicetree, and are selected during a mux
> > request by querying a new 'ip' member in struct aspeed_sig_desc.
> >
> > > > Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
> > ---
> > Since v1:
> >
> > The change is now proactive: instead of reporting that we need to flip bits in
> > controllers we can't access, the patch provides access via regmaps for the
> > relevant controllers. The implementation also splits out the IP block ID into
> > its own variable rather than packing the value into the upper bits of the reg
> > member of struct aspeed_sig_desc. This drives some churn in the diff, but I've
> > tried to minimise it.
> >
> > .../devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 50 +++++++++++++---
> > drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 18 +++---
> > drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 39 ++++++++++---
> > drivers/pinctrl/aspeed/pinctrl-aspeed.c | 66 +++++++++++++---------
> > drivers/pinctrl/aspeed/pinctrl-aspeed.h | 32 ++++++++---
> > 5 files changed, 144 insertions(+), 61 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> > index 2ad18c4ea55c..115b0cce6c1c 100644
> > --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> > +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> > @@ -4,12 +4,19 @@ Aspeed Pin Controllers
> > The Aspeed SoCs vary in functionality inside a generation but have a common mux
> > device register layout.
> >
> > -Required properties:
> > -- compatible : Should be any one of the following:
> > - "aspeed,ast2400-pinctrl"
> > - "aspeed,g4-pinctrl"
> > - "aspeed,ast2500-pinctrl"
> > - "aspeed,g5-pinctrl"
> > +Required properties for g4:
> > +- compatible : Should be any one of the following:
> > + "aspeed,ast2400-pinctrl"
> > + "aspeed,g4-pinctrl"
> > +
> > +Required properties for g5:
> > +- compatible : Should be any one of the following:
> > + "aspeed,ast2500-pinctrl"
> > + "aspeed,g5-pinctrl"
> > +
> > +- aspeed,external-nodes: A cell of phandles to external controller nodes:
> > + 0: compatible with "aspeed,ast2500-gfx", "syscon"
> > + 1: compatible with "aspeed,ast2500-lpchc", "syscon"
> >
> > The pin controller node should be a child of a syscon node with the required
> > property:
> > @@ -47,7 +54,7 @@ RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6
> > TIMER7 TIMER8 VGABIOSROM
> >
> >
> > -Examples:
> > +g4 Example:
> >
> > syscon: scu@1e6e2000 {
> > compatible = "syscon", "simple-mfd";
> > @@ -63,5 +70,34 @@ syscon: scu@1e6e2000 {
> > };
> > };
> >
> > +g5 Example:
> > +
> > +apb {
> > + gfx: display@1e6e6000 {
> > + compatible = "aspeed,ast2500-gfx", "syscon";
> > + reg = <0x1e6e6000 0x1000>;
> > + };
> > +
> > + lpchc: lpchc@1e7890a0 {
> > + compatible = "aspeed,ast2500-lpchc", "syscon";
> > + reg = <0x1e7890a0 0xc4>;
> > + };
> > +
> > + syscon: scu@1e6e2000 {
> > + compatible = "syscon", "simple-mfd";
> > + reg = <0x1e6e2000 0x1a8>;
> > +
> > + pinctrl: pinctrl {
>
> Why the single child node here? Doesn't look like any reason for it in
> the example.
The SCU contains other miscellaneous functionality besides pinctrl
registers, but that's not relevant for the pinctrl bindings. This is an
example for the g5 SoCs demonstrating use of the aspeed,external-nodes
property, which isn't required for the g4 and is why I split the
examples.
Maybe I should split out the bindings for each SoC generation into
separate files?
>
> > + compatible = "aspeed,g5-pinctrl";
> > + aspeed,external-nodes = <&gfx, &lpchc>;
You didn't comment on my approach here, but I'm interested in feedback.
I've gone the route of fixed ordering of the phandles, but there are
two other approaches:
1. Relax the fixed ordering requirement by adding an "aspeed,external-
node-names" property and requiring correlated indices between them
2. Using separate properties for each required external node
Approach 1 seems pretty idiomatic and only crossed my mind after I'd
sent the patch. Approach 2 seems a bit ugly as the number of properties
scales with the number of controllers participating in the pinmux
configuration.
Something that also wasn't clear to me was whether I need the "aspeed"
prefix on the property name. What's the convention here? Do I need it
in this case?
Cheers,
Andrew
> > +
> > > > + pinctrl_i2c3_default: i2c3_default {
> > > > + function = "I2C3";
> > > > + groups = "I2C3";
> > > > + };
> > > > + };
> > > > + };
> > +};
> > +
> > Please refer to pinctrl-bindings.txt in this directory for details of the
> > common pinctrl bindings used by client devices.
[-- Attachment #2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 801 bytes --]
^ permalink raw reply
* Re: [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm
From: Tony Lindgren @ 2016-11-09 23:00 UTC (permalink / raw)
To: Lokesh Vutla
Cc: Linux OMAP Mailing List, Tero Kristo, Sekhar Nori, Nishanth Menon,
Device Tree Mailing List, Rob Herring, Linux ARM Mailing List
In-Reply-To: <1b9c4d14-78d7-841f-776c-63a8c1ae1fb1-l0cyMroinI0@public.gmane.org>
* Lokesh Vutla <lokeshvutla-l0cyMroinI0@public.gmane.org> [161106 20:50]:
> Hi Tony,
>
> On Friday 21 October 2016 04:08 PM, Lokesh Vutla wrote:
> > This series does minor dts cleanup for dra72-evm and adds support for
> > DRA718-evm.
>
> Do you have any comments on this series?
Looks good to me except for the regulator patch that you need to repost.
Applying the rest split into various topic branches for soc/dt/defconfig.
Regards,
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH 0/3] ARM: dts: am33xx: Add clock info to rtc nodes
From: Tony Lindgren @ 2016-11-09 22:47 UTC (permalink / raw)
To: Keerthy
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
t-kristo-l0cyMroinI0
In-Reply-To: <b5aa9c3b-e922-404d-3e0a-8a84dd3bce2a-l0cyMroinI0@public.gmane.org>
* Keerthy <j-keerthy-l0cyMroinI0@public.gmane.org> [161106 21:25]:
>
>
> On Thursday 27 October 2016 11:18 AM, Keerthy wrote:
> > The series adds the clock info to rtc node.
> >
> > Boot tested and checked for rtc ticking on am335x-boneblack, am335x-bone
> > am437x-gp-evm.
>
> Tony,
>
> The relevant driver changes are already pulled by Alexandre Belloni.
> https://patchwork.kernel.org/patch/9398903/.
>
> Hope you call pull this set.
Applying into omap-for-v4.10/dt thanks.
Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH v2 3/3] ASoC: atmel: tse850: add ASoC driver for the Axentia TSE-850
From: Peter Rosin @ 2016-11-09 22:40 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Liam Girdwood, Mark Brown, Rob Herring, Mark Rutland,
Nicolas Ferre, Jaroslav Kysela, Takashi Iwai,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1478731258-26084-1-git-send-email-peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
MAINTAINERS | 1 +
sound/soc/atmel/Kconfig | 10 +
sound/soc/atmel/Makefile | 2 +
sound/soc/atmel/tse850-pcm5142.c | 472 +++++++++++++++++++++++++++++++++++++++
4 files changed, 485 insertions(+)
create mode 100644 sound/soc/atmel/tse850-pcm5142.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 4f2ebf3ab51a..4ce45f02d83f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2323,6 +2323,7 @@ M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
L: alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw@public.gmane.org (moderated for non-subscribers)
S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
+F: sound/soc/atmel/tse850-pcm5142.c
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
diff --git a/sound/soc/atmel/Kconfig b/sound/soc/atmel/Kconfig
index 22aec9a1e9a4..4a56f3dfba51 100644
--- a/sound/soc/atmel/Kconfig
+++ b/sound/soc/atmel/Kconfig
@@ -78,4 +78,14 @@ config SND_ATMEL_SOC_PDMIC
help
Say Y if you want to add support for Atmel ASoC driver for boards using
PDMIC.
+
+config SND_ATMEL_SOC_TSE850_PCM5142
+ tristate "ASoC driver for the Axentia TSE-850"
+ depends on ARCH_AT91 && OF
+ depends on ATMEL_SSC && I2C
+ select SND_ATMEL_SOC_SSC_DMA
+ select SND_SOC_PCM512x_I2C
+ help
+ Say Y if you want to add support for the ASoC driver for the
+ Axentia TSE-850 with a PCM5142 codec.
endif
diff --git a/sound/soc/atmel/Makefile b/sound/soc/atmel/Makefile
index a2b127bd9c87..67e10cbd4ed7 100644
--- a/sound/soc/atmel/Makefile
+++ b/sound/soc/atmel/Makefile
@@ -13,9 +13,11 @@ snd-atmel-soc-wm8904-objs := atmel_wm8904.o
snd-soc-sam9x5-wm8731-objs := sam9x5_wm8731.o
snd-atmel-soc-classd-objs := atmel-classd.o
snd-atmel-soc-pdmic-objs := atmel-pdmic.o
+snd-atmel-soc-tse850-pcm5142-objs := tse850-pcm5142.o
obj-$(CONFIG_SND_AT91_SOC_SAM9G20_WM8731) += snd-soc-sam9g20-wm8731.o
obj-$(CONFIG_SND_ATMEL_SOC_WM8904) += snd-atmel-soc-wm8904.o
obj-$(CONFIG_SND_AT91_SOC_SAM9X5_WM8731) += snd-soc-sam9x5-wm8731.o
obj-$(CONFIG_SND_ATMEL_SOC_CLASSD) += snd-atmel-soc-classd.o
obj-$(CONFIG_SND_ATMEL_SOC_PDMIC) += snd-atmel-soc-pdmic.o
+obj-$(CONFIG_SND_ATMEL_SOC_TSE850_PCM5142) += snd-atmel-soc-tse850-pcm5142.o
diff --git a/sound/soc/atmel/tse850-pcm5142.c b/sound/soc/atmel/tse850-pcm5142.c
new file mode 100644
index 000000000000..ac6a814c8ecf
--- /dev/null
+++ b/sound/soc/atmel/tse850-pcm5142.c
@@ -0,0 +1,472 @@
+/*
+ * TSE-850 audio - ASoC driver for the Axentia TSE-850 with a PCM5142 codec
+ *
+ * Copyright (C) 2016 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * loop1 relays
+ * IN1 +---o +------------+ o---+ OUT1
+ * \ /
+ * + +
+ * | / |
+ * +--o +--. |
+ * | add | |
+ * | V |
+ * | .---. |
+ * DAC +----------->|Sum|---+
+ * | '---' |
+ * | |
+ * + +
+ *
+ * IN2 +---o--+------------+--o---+ OUT2
+ * loop2 relays
+ *
+ * The 'loop1' gpio pin controlls two relays, which are either in loop
+ * position, meaning that input and output are directly connected, or
+ * they are in mixer position, meaning that the signal is passed through
+ * the 'Sum' mixer. Similarly for 'loop2'.
+ *
+ * In the above, the 'loop1' relays are inactive, thus feeding IN1 to the
+ * mixer (if 'add' is active) and feeding the mixer output to OUT1. The
+ * 'loop2' relays are active, short-cutting the TSE-850 from channel 2.
+ * IN1, IN2, OUT1 and OUT2 are TSE-850 connectors and DAC is the PCB name
+ * of the (filtered) output from the PCM5142 codec.
+ */
+
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/regulator/consumer.h>
+
+#include <sound/soc.h>
+#include <sound/pcm_params.h>
+
+#include "atmel_ssc_dai.h"
+
+struct tse850_priv {
+ int ssc_id;
+
+ struct gpio_desc *add;
+ struct gpio_desc *loop1;
+ struct gpio_desc *loop2;
+
+ struct regulator *ana;
+
+ int add_cache;
+ int loop1_cache;
+ int loop2_cache;
+};
+
+static int tse850_get_mux1(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+ ucontrol->value.enumerated.item[0] = tse850->loop1_cache;
+
+ return 0;
+}
+
+static int tse850_put_mux1(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+ struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+ unsigned int val = ucontrol->value.enumerated.item[0];
+
+ if (val >= e->items)
+ return -EINVAL;
+
+ gpiod_set_value_cansleep(tse850->loop1, val);
+ tse850->loop1_cache = val;
+
+ return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+static int tse850_get_mux2(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+ ucontrol->value.enumerated.item[0] = tse850->loop2_cache;
+
+ return 0;
+}
+
+static int tse850_put_mux2(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+ struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+ unsigned int val = ucontrol->value.enumerated.item[0];
+
+ if (val >= e->items)
+ return -EINVAL;
+
+ gpiod_set_value_cansleep(tse850->loop2, val);
+ tse850->loop2_cache = val;
+
+ return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+int tse850_get_mix(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+ ucontrol->value.enumerated.item[0] = tse850->add_cache;
+
+ return 0;
+}
+
+int tse850_put_mix(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+ int connect = !!ucontrol->value.integer.value[0];
+
+ if (tse850->add_cache == connect)
+ return 0;
+
+ /*
+ * Hmmm, this gpiod_set_value_cansleep call should probably happen
+ * inside snd_soc_dapm_mixer_update_power in the loop.
+ */
+ gpiod_set_value_cansleep(tse850->add, connect);
+ tse850->add_cache = connect;
+
+ snd_soc_dapm_mixer_update_power(dapm, kctrl, connect, NULL);
+ return 1;
+}
+
+int tse850_get_ana(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+ int ret;
+
+ ret = regulator_get_voltage(tse850->ana);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Map regulator output values like so:
+ * -11.5V to "Low" (enum 0)
+ * 11.5V-12.5V to "12V" (enum 1)
+ * 12.5V-13.5V to "13V" (enum 2)
+ * ...
+ * 18.5V-19.5V to "19V" (enum 8)
+ * 19.5V- to "20V" (enum 9)
+ */
+ if (ret < 11000000)
+ ret = 11000000;
+ else if (ret > 20000000)
+ ret = 20000000;
+ ret -= 11000000;
+ ret = (ret + 500000) / 1000000;
+
+ ucontrol->value.enumerated.item[0] = ret;
+
+ return 0;
+}
+
+int tse850_put_ana(struct snd_kcontrol *kctrl,
+ struct snd_ctl_elem_value *ucontrol)
+{
+ struct snd_soc_dapm_context *dapm = snd_soc_dapm_kcontrol_dapm(kctrl);
+ struct snd_soc_card *card = dapm->card;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+ struct soc_enum *e = (struct soc_enum *)kctrl->private_value;
+ unsigned int uV = ucontrol->value.enumerated.item[0];
+ int ret;
+
+ if (uV >= e->items)
+ return -EINVAL;
+
+ /*
+ * Map enum zero (Low) to 2 volts on the regulator, do this since
+ * the ana regulator is supplied by the system 12V voltage and
+ * requesting anything below the system voltage causes the system
+ * voltage to be passed through the regulator. Also, the ana
+ * regulator induces noise when requesting voltages near the
+ * system voltage. So, by mapping Low to 2V, that noise is
+ * eliminated when all that is needed is 12V (the system voltage).
+ */
+ if (uV)
+ uV = 11000000 + (1000000 * uV);
+ else
+ uV = 2000000;
+
+ ret = regulator_set_voltage(tse850->ana, uV, uV);
+ if (ret < 0)
+ return ret;
+
+ return snd_soc_dapm_put_enum_double(kctrl, ucontrol);
+}
+
+static const char * const mux_text[] = { "Mixer", "Loop" };
+
+static const struct soc_enum mux_enum =
+ SOC_ENUM_SINGLE(SND_SOC_NOPM, 0, 2, mux_text);
+
+static const struct snd_kcontrol_new mux1 =
+ SOC_DAPM_ENUM_EXT("MUX1", mux_enum, tse850_get_mux1, tse850_put_mux1);
+
+static const struct snd_kcontrol_new mux2 =
+ SOC_DAPM_ENUM_EXT("MUX2", mux_enum, tse850_get_mux2, tse850_put_mux2);
+
+#define TSE850_DAPM_SINGLE_EXT(xname, reg, shift, max, invert, xget, xput) \
+{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = xname, \
+ .info = snd_soc_info_volsw, \
+ .get = xget, \
+ .put = xput, \
+ .private_value = SOC_SINGLE_VALUE(reg, shift, max, invert, 0) }
+
+static const struct snd_kcontrol_new mix[] = {
+ TSE850_DAPM_SINGLE_EXT("IN Switch", SND_SOC_NOPM, 0, 1, 0,
+ tse850_get_mix, tse850_put_mix),
+};
+
+static const char * const ana_text[] = {
+ "Low", "12V", "13V", "14V", "15V", "16V", "17V", "18V", "19V", "20V"
+};
+
+static const struct soc_enum ana_enum =
+ SOC_ENUM_SINGLE(SND_SOC_NOPM, 0, 9, ana_text);
+
+static const struct snd_kcontrol_new out =
+ SOC_DAPM_ENUM_EXT("ANA", ana_enum, tse850_get_ana, tse850_put_ana);
+
+static const struct snd_soc_dapm_widget tse850_dapm_widgets[] = {
+ SND_SOC_DAPM_LINE("OUT1", NULL),
+ SND_SOC_DAPM_LINE("OUT2", NULL),
+ SND_SOC_DAPM_LINE("IN1", NULL),
+ SND_SOC_DAPM_LINE("IN2", NULL),
+ SND_SOC_DAPM_INPUT("DAC"),
+ SND_SOC_DAPM_AIF_IN("AIFINL", "Playback", 0, SND_SOC_NOPM, 0, 0),
+ SND_SOC_DAPM_AIF_IN("AIFINR", "Playback", 1, SND_SOC_NOPM, 0, 0),
+ SOC_MIXER_ARRAY("MIX", SND_SOC_NOPM, 0, 0, mix),
+ SND_SOC_DAPM_MUX("MUX1", SND_SOC_NOPM, 0, 0, &mux1),
+ SND_SOC_DAPM_MUX("MUX2", SND_SOC_NOPM, 0, 0, &mux2),
+ SND_SOC_DAPM_OUT_DRV("OUT", SND_SOC_NOPM, 0, 0, &out, 1),
+};
+
+/*
+ * These connections are not entirely correct, since both IN1 and IN2
+ * are always fed to MIX (if the "IN switch" is set so), i.e. without
+ * regard to the loop1 and loop2 relays that according to this only
+ * control MUX1 and MUX2 but in fact also control how the input signals
+ * are routed.
+ * But, 1) I don't know how to do it right, and 2) it doesn't seem to
+ * matter in practice since nothing is powered in those sections anyway.
+ */
+static const struct snd_soc_dapm_route tse850_intercon[] = {
+ { "OUT1", NULL, "MUX1" },
+ { "OUT2", NULL, "MUX2" },
+
+ { "MUX1", "Loop", "IN1" },
+ { "MUX1", "Mixer", "OUT" },
+
+ { "MUX2", "Loop", "IN2" },
+ { "MUX2", "Mixer", "OUT" },
+
+ { "OUT", NULL, "MIX" },
+
+ { "MIX", NULL, "DAC" },
+ { "MIX", "IN Switch", "IN1" },
+ { "MIX", "IN Switch", "IN2" },
+
+ /* connect board input to the codec left channel output pin */
+ { "DAC", NULL, "OUTL" },
+};
+
+static struct snd_soc_dai_link tse850_dailink = {
+ .name = "TSE-850",
+ .stream_name = "TSE-850-PCM",
+ .codec_dai_name = "pcm512x-hifi",
+ .dai_fmt = SND_SOC_DAIFMT_I2S
+ | SND_SOC_DAIFMT_NB_NF
+ | SND_SOC_DAIFMT_CBM_CFS,
+};
+
+static struct snd_soc_card tse850_card = {
+ .name = "TSE-850-ASoC",
+ .owner = THIS_MODULE,
+ .dai_link = &tse850_dailink,
+ .num_links = 1,
+ .dapm_widgets = tse850_dapm_widgets,
+ .num_dapm_widgets = ARRAY_SIZE(tse850_dapm_widgets),
+ .dapm_routes = tse850_intercon,
+ .num_dapm_routes = ARRAY_SIZE(tse850_intercon),
+ .fully_routed = true,
+};
+
+static int tse850_dt_init(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *codec_np, *cpu_np;
+ struct snd_soc_card *card = &tse850_card;
+ struct snd_soc_dai_link *dailink = &tse850_dailink;
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+ if (!np) {
+ dev_err(&pdev->dev, "only device tree supported\n");
+ return -EINVAL;
+ }
+
+ cpu_np = of_parse_phandle(np, "axentia,ssc-controller", 0);
+ if (!cpu_np) {
+ dev_err(&pdev->dev, "failed to get dai and pcm info\n");
+ return -EINVAL;
+ }
+ dailink->cpu_of_node = cpu_np;
+ dailink->platform_of_node = cpu_np;
+ tse850->ssc_id = of_alias_get_id(cpu_np, "ssc");
+ of_node_put(cpu_np);
+
+ codec_np = of_parse_phandle(np, "axentia,audio-codec", 0);
+ if (!codec_np) {
+ dev_err(&pdev->dev, "failed to get codec info\n");
+ return -EINVAL;
+ }
+ dailink->codec_of_node = codec_np;
+ of_node_put(codec_np);
+
+ return 0;
+}
+
+static int tse850_probe(struct platform_device *pdev)
+{
+ struct snd_soc_card *card = &tse850_card;
+ struct device *dev = card->dev = &pdev->dev;
+ struct tse850_priv *tse850;
+ int ret;
+
+ tse850 = devm_kzalloc(dev, sizeof(*tse850), GFP_KERNEL);
+ if (!tse850)
+ return -ENOMEM;
+
+ snd_soc_card_set_drvdata(card, tse850);
+
+ ret = tse850_dt_init(pdev);
+ if (ret) {
+ dev_err(dev, "failed to init dt info\n");
+ return ret;
+ }
+
+ tse850->add = devm_gpiod_get(dev, "axentia,add", GPIOD_OUT_HIGH);
+ if (IS_ERR(tse850->add)) {
+ if (PTR_ERR(tse850->add) != -EPROBE_DEFER)
+ dev_err(dev, "failed to get 'add' gpio\n");
+ return PTR_ERR(tse850->add);
+ }
+ tse850->add_cache = 1;
+
+ tse850->loop1 = devm_gpiod_get(dev, "axentia,loop1", GPIOD_OUT_HIGH);
+ if (IS_ERR(tse850->loop1)) {
+ if (PTR_ERR(tse850->loop1) != -EPROBE_DEFER)
+ dev_err(dev, "failed to get 'loop1' gpio\n");
+ return PTR_ERR(tse850->loop1);
+ }
+ tse850->loop1_cache = 1;
+
+ tse850->loop2 = devm_gpiod_get(dev, "axentia,loop2", GPIOD_OUT_HIGH);
+ if (IS_ERR(tse850->loop2)) {
+ if (PTR_ERR(tse850->loop2) != -EPROBE_DEFER)
+ dev_err(dev, "failed to get 'loop2' gpio\n");
+ return PTR_ERR(tse850->loop2);
+ }
+ tse850->loop2_cache = 1;
+
+ tse850->ana = devm_regulator_get(dev, "axentia,ana");
+ if (IS_ERR(tse850->ana)) {
+ if (PTR_ERR(tse850->ana) != -EPROBE_DEFER)
+ dev_err(dev, "failed to get 'ana' regulator\n");
+ return PTR_ERR(tse850->ana);
+ }
+
+ ret = regulator_enable(tse850->ana);
+ if (ret < 0) {
+ dev_err(dev, "failed to enable the 'ana' regulator\n");
+ return ret;
+ }
+
+ ret = atmel_ssc_set_audio(tse850->ssc_id);
+ if (ret != 0) {
+ dev_err(dev,
+ "failed to set SSC %d for audio\n", tse850->ssc_id);
+ goto err_disable_ana;
+ }
+
+ ret = snd_soc_register_card(card);
+ if (ret) {
+ dev_err(dev, "snd_soc_register_card failed\n");
+ goto err_put_audio;
+ }
+
+ return 0;
+
+err_put_audio:
+ atmel_ssc_put_audio(tse850->ssc_id);
+err_disable_ana:
+ regulator_disable(tse850->ana);
+ return ret;
+}
+
+static int tse850_remove(struct platform_device *pdev)
+{
+ struct snd_soc_card *card = platform_get_drvdata(pdev);
+ struct tse850_priv *tse850 = snd_soc_card_get_drvdata(card);
+
+ snd_soc_unregister_card(card);
+ atmel_ssc_put_audio(tse850->ssc_id);
+ regulator_disable(tse850->ana);
+
+ return 0;
+}
+
+static const struct of_device_id tse850_dt_ids[] = {
+ { .compatible = "axentia,tse850-pcm5142", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, tse850_dt_ids);
+
+static struct platform_driver tse850_driver = {
+ .driver = {
+ .name = "axentia-tse850-pcm5142",
+ .of_match_table = of_match_ptr(tse850_dt_ids),
+ },
+ .probe = tse850_probe,
+ .remove = tse850_remove,
+};
+
+module_platform_driver(tse850_driver);
+
+/* Module information */
+MODULE_AUTHOR("Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>");
+MODULE_DESCRIPTION("ALSA SoC driver for TSE-850 with PCM5142 codec");
+MODULE_LICENSE("GPL");
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v2 2/3] ASoC: tse850: document axentia,tse850-pcm5142 bindings
From: Peter Rosin @ 2016-11-09 22:40 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Liam Girdwood, Mark Brown, Rob Herring, Mark Rutland,
Nicolas Ferre, Jaroslav Kysela, Takashi Iwai,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1478731258-26084-1-git-send-email-peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Signed-off-by: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
---
.../bindings/sound/axentia,tse850-pcm5142.txt | 88 ++++++++++++++++++++++
MAINTAINERS | 6 ++
2 files changed, 94 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
diff --git a/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
new file mode 100644
index 000000000000..0c2d44fda17e
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
@@ -0,0 +1,88 @@
+ASoC driver for the Axentia TSE-850 with a PCM5142 codec
+
+Required properties:
+ - compatible: "axentia,tse850-pcm5142"
+ - axentia,ssc-controller: The phandle of the atmel SSC controller used as
+ cpu dai.
+ - axentia,audio-codec: The phandle of the PCM5142 codec.
+ - axentia,add-gpios: gpio specifier that controls the mixer.
+ - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1.
+ - axentia,loop2-gpios: gpio specifier that controls loop relays on channel 2.
+ - axentia,ana-supply: Regulator that supplies the output amplifier. Must
+ support voltages in the 2V - 20V range, in 1V steps.
+
+The schematics explaining the gpios are as follows:
+
+ loop1 relays
+ IN1 +---o +------------+ o---+ OUT1
+ \ /
+ + +
+ | / |
+ +--o +--. |
+ | add | |
+ | V |
+ | .---. |
+ DAC +----------->|Sum|---+
+ | '---' |
+ | |
+ + +
+
+ IN2 +---o--+------------+--o---+ OUT2
+ loop2 relays
+
+The 'loop1' gpio pin controlls two relays, which are either in loop position,
+meaning that input and output are directly connected, or they are in mixer
+position, meaning that the signal is passed through the 'Sum' mixer. Similarly
+for 'loop2'.
+
+In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer
+(if 'add' is active) and feeding the mixer output to OUT1. The 'loop2' relays
+are active, short-cutting the TSE-850 from channel 2. IN1, IN2, OUT1 and OUT2
+are TSE-850 connectors and DAC is the PCB name of the (filtered) output from
+the PCM5142 codec.
+
+Example:
+
+ &i2c {
+ codec: pcm5142@4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+ };
+
+ ana: ana-reg {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,ssc-controller = <&ssc0>;
+ axentia,audio-codec = <&codec>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 539b20baf791..4f2ebf3ab51a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2318,6 +2318,12 @@ F: include/uapi/linux/ax25.h
F: include/net/ax25.h
F: net/ax25/
+AXENTIA ASOC DRIVERS
+M: Peter Rosin <peda-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
+L: alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw@public.gmane.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/sound/axentia,*
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab-JsYNTwtnfakRB7SZvlqPiA@public.gmane.org>
M: Mauro Carvalho Chehab <mchehab-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v2 1/3] ASoC: atmel_ssc_dai: if not provided, default to sensible TCMR/RCMR periods
From: Peter Rosin @ 2016-11-09 22:40 UTC (permalink / raw)
To: linux-kernel
Cc: Peter Rosin, Liam Girdwood, Mark Brown, Rob Herring, Mark Rutland,
Nicolas Ferre, Jaroslav Kysela, Takashi Iwai, alsa-devel,
devicetree
In-Reply-To: <1478731258-26084-1-git-send-email-peda@axentia.se>
When this driver runs the dai link frame clock, and noone has stated
differently, assume that all the bits of a frame are used.
This relieves the cpu dai users from the duty to fill in the dividers for
the common case.
Signed-off-by: Peter Rosin <peda@axentia.se>
---
sound/soc/atmel/atmel_ssc_dai.c | 29 +++++++++++++++++++++++------
sound/soc/atmel/atmel_ssc_dai.h | 1 +
2 files changed, 24 insertions(+), 6 deletions(-)
diff --git a/sound/soc/atmel/atmel_ssc_dai.c b/sound/soc/atmel/atmel_ssc_dai.c
index 16e459aedffe..674191508437 100644
--- a/sound/soc/atmel/atmel_ssc_dai.c
+++ b/sound/soc/atmel/atmel_ssc_dai.c
@@ -380,6 +380,7 @@ static void atmel_ssc_shutdown(struct snd_pcm_substream *substream,
ssc_writel(ssc_p->ssc->regs, CR, SSC_BIT(CR_SWRST));
/* Clear the SSC dividers */
ssc_p->cmr_div = ssc_p->tcmr_period = ssc_p->rcmr_period = 0;
+ ssc_p->forced_divider = 0;
}
spin_unlock_irq(&ssc_p->lock);
@@ -429,10 +430,12 @@ static int atmel_ssc_set_dai_clkdiv(struct snd_soc_dai *cpu_dai,
break;
case ATMEL_SSC_TCMR_PERIOD:
+ ssc_p->forced_divider |= BIT(ATMEL_SSC_TCMR_PERIOD);
ssc_p->tcmr_period = div;
break;
case ATMEL_SSC_RCMR_PERIOD:
+ ssc_p->forced_divider |= BIT(ATMEL_SSC_RCMR_PERIOD);
ssc_p->rcmr_period = div;
break;
@@ -459,6 +462,8 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
u32 tfmr, rfmr, tcmr, rcmr;
int ret;
int fslen, fslen_ext;
+ u32 tcmr_period;
+ u32 rcmr_period;
/*
* Currently, there is only one set of dma params for
@@ -470,6 +475,18 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
else
dir = 1;
+ /*
+ * If the cpu dai should provide the frame clock,
+ * but noone has provided the dividers needed for
+ * that to work, fall back to something sensible.
+ */
+ tcmr_period = ssc_p->tcmr_period;
+ if (!(ssc_p->forced_divider & BIT(ATMEL_SSC_TCMR_PERIOD)))
+ tcmr_period = snd_soc_params_to_frame_size(params) / 2 - 1;
+ rcmr_period = ssc_p->rcmr_period;
+ if (!(ssc_p->forced_divider & BIT(ATMEL_SSC_RCMR_PERIOD)))
+ rcmr_period = snd_soc_params_to_frame_size(params) / 2 - 1;
+
dma_params = ssc_p->dma_params[dir];
channels = params_channels(params);
@@ -524,7 +541,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
fslen_ext = (bits - 1) / 16;
fslen = (bits - 1) % 16;
- rcmr = SSC_BF(RCMR_PERIOD, ssc_p->rcmr_period)
+ rcmr = SSC_BF(RCMR_PERIOD, rcmr_period)
| SSC_BF(RCMR_STTDLY, START_DELAY)
| SSC_BF(RCMR_START, SSC_START_FALLING_RF)
| SSC_BF(RCMR_CKI, SSC_CKI_RISING)
@@ -540,7 +557,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
| SSC_BF(RFMR_LOOP, 0)
| SSC_BF(RFMR_DATLEN, (bits - 1));
- tcmr = SSC_BF(TCMR_PERIOD, ssc_p->tcmr_period)
+ tcmr = SSC_BF(TCMR_PERIOD, tcmr_period)
| SSC_BF(TCMR_STTDLY, START_DELAY)
| SSC_BF(TCMR_START, SSC_START_FALLING_RF)
| SSC_BF(TCMR_CKI, SSC_CKI_FALLING)
@@ -606,7 +623,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
fslen_ext = (bits - 1) / 16;
fslen = (bits - 1) % 16;
- rcmr = SSC_BF(RCMR_PERIOD, ssc_p->rcmr_period)
+ rcmr = SSC_BF(RCMR_PERIOD, rcmr_period)
| SSC_BF(RCMR_STTDLY, START_DELAY)
| SSC_BF(RCMR_START, SSC_START_FALLING_RF)
| SSC_BF(RCMR_CKI, SSC_CKI_RISING)
@@ -623,7 +640,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
| SSC_BF(RFMR_LOOP, 0)
| SSC_BF(RFMR_DATLEN, (bits - 1));
- tcmr = SSC_BF(TCMR_PERIOD, ssc_p->tcmr_period)
+ tcmr = SSC_BF(TCMR_PERIOD, tcmr_period)
| SSC_BF(TCMR_STTDLY, START_DELAY)
| SSC_BF(TCMR_START, SSC_START_FALLING_RF)
| SSC_BF(TCMR_CKI, SSC_CKI_FALLING)
@@ -650,7 +667,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
* MCK divider, and the BCLK signal is output
* on the SSC TK line.
*/
- rcmr = SSC_BF(RCMR_PERIOD, ssc_p->rcmr_period)
+ rcmr = SSC_BF(RCMR_PERIOD, rcmr_period)
| SSC_BF(RCMR_STTDLY, 1)
| SSC_BF(RCMR_START, SSC_START_RISING_RF)
| SSC_BF(RCMR_CKI, SSC_CKI_RISING)
@@ -665,7 +682,7 @@ static int atmel_ssc_hw_params(struct snd_pcm_substream *substream,
| SSC_BF(RFMR_LOOP, 0)
| SSC_BF(RFMR_DATLEN, (bits - 1));
- tcmr = SSC_BF(TCMR_PERIOD, ssc_p->tcmr_period)
+ tcmr = SSC_BF(TCMR_PERIOD, tcmr_period)
| SSC_BF(TCMR_STTDLY, 1)
| SSC_BF(TCMR_START, SSC_START_RISING_RF)
| SSC_BF(TCMR_CKI, SSC_CKI_FALLING)
diff --git a/sound/soc/atmel/atmel_ssc_dai.h b/sound/soc/atmel/atmel_ssc_dai.h
index 80b153857a88..75194f582131 100644
--- a/sound/soc/atmel/atmel_ssc_dai.h
+++ b/sound/soc/atmel/atmel_ssc_dai.h
@@ -113,6 +113,7 @@ struct atmel_ssc_info {
unsigned short cmr_div;
unsigned short tcmr_period;
unsigned short rcmr_period;
+ unsigned int forced_divider;
struct atmel_pcm_dma_params *dma_params[2];
struct atmel_ssc_state ssc_state;
unsigned long mck_rate;
--
2.1.4
^ permalink raw reply related
* [PATCH v2 0/3] ASoC driver for the TSE-850
From: Peter Rosin @ 2016-11-09 22:40 UTC (permalink / raw)
To: linux-kernel-u79uwXL29TY76Z2rM5mHXA
Cc: Peter Rosin, Liam Girdwood, Mark Brown, Rob Herring, Mark Rutland,
Nicolas Ferre, Jaroslav Kysela, Takashi Iwai,
alsa-devel-K7yf7f+aM1XWsZ/bQMPhNw,
devicetree-u79uwXL29TY76Z2rM5mHXA
Hi!
v1 -> v2 changes:
- new subject for the bindings patch to make it easier to find
- move the driver to the sound/soc/atmel directory
- add cached values for add/loop1/loop2 to avoid gets from output gpios
- use _cansleep when updating gpios
- add comment on how the regulator voltage is mapped to the ana enum
- drop the .hw_params hook that did set the cpu dai divider and...
- ...add a preparatory patch that does this in the cpu dai driver instead
- drop .init and set the dapm routes directly in the card struct instead
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
This adds a driver for the "sound" bits of the device (quoted since it
is normally not used for normal sound output, but that works too of
course).
I have not provided a patch to add axentia as a devicetree vendor prefix,
since such a patch is already pending in an IIO series [1] that seems
close to being accepted.
However, there are a couple of points that I'm not 100% satisfied with
for this driver.
First, I do not know how to describe the relays that control if the
IN1/IN2 signals are directly routed towards OUT1/OUT2 or if they are
routed to the "add" switch. The dapm routing treats this as if the
IN1/IN2 signals are always routed to both the "add" switch and to
the muxes feeding OUT1/OUT2. This is fine with me since nothing is
powered in those sections anyway, so what dapm thinks does not really
matter. But it is a wart all the same.
Second, there's my comment in tse850_put_mix() when the "add" switch
is updated. I believe this update should really happen as a side
effect of the call to snd_soc_dapm_mixer_update_power(), so that it
happens at the right point compared to other stuff that is powered.
But I do not know how to hook that up and instead I flip the switch
before the call since it doesn't really matter. I.e., any noise
resulting from this badness is negligeble in practice.
Cheers,
Peter
[1] http://lwn.net/Articles/705931
Peter Rosin (3):
ASoC: atmel_ssc_dai: if not provided, default to sensible TCMR/RCMR
periods
ASoC: tse850: document axentia,tse850-pcm5142 bindings
ASoC: atmel: tse850: add ASoC driver for the Axentia TSE-850
.../bindings/sound/axentia,tse850-pcm5142.txt | 88 ++++
MAINTAINERS | 7 +
sound/soc/atmel/Kconfig | 10 +
sound/soc/atmel/Makefile | 2 +
sound/soc/atmel/atmel_ssc_dai.c | 29 +-
sound/soc/atmel/atmel_ssc_dai.h | 1 +
sound/soc/atmel/tse850-pcm5142.c | 472 +++++++++++++++++++++
7 files changed, 603 insertions(+), 6 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/axentia,tse850-pcm5142.txt
create mode 100644 sound/soc/atmel/tse850-pcm5142.c
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v6 5/8] DT:omap3+tsc2007: use new common touchscreen bindings
From: Tony Lindgren @ 2016-11-09 22:27 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: Dmitry Torokhov, Rob Herring, Mark Rutland, Benoît Cousson,
Russell King, Arnd Bergmann, Michael Welling, Mika Penttilä,
Javier Martinez Canillas, Igor Grinberg, Sebastian Reichel,
Andrew F. Davis, Mark Brown, Jonathan Cameron, Hans de Goede,
Sangwon Jee, linux-input, devicetree, linux-kernel, linux-omap,
letux-kernel
In-Reply-To: <72927a5b3d5b9f33dfd57a68ef1de9cb0a536407.1477557860.git.hns@goldelico.com>
* H. Nikolaus Schaller <hns@goldelico.com> [161027 01:47]:
> While we fix the GTA04 we add proper pinmux for the
> penirq gpio.
>
> Tested on: GTA04A4 and Pyra-Handheld
>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
This should be safe to merge along with the driver changes:
Acked-by: Tony Lindgren <tony@atomide.com>
> ---
> arch/arm/boot/dts/omap3-gta04.dtsi | 25 +++++++++++++++++++++++--
> 1 file changed, 23 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
> index b3a8b1f..64d6ee3 100644
> --- a/arch/arm/boot/dts/omap3-gta04.dtsi
> +++ b/arch/arm/boot/dts/omap3-gta04.dtsi
> @@ -273,6 +273,13 @@
> OMAP3_CORE1_IOPAD(0x2134, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio112 */
> >;
> };
> +
> + penirq_pins: pinmux_penirq_pins {
> + pinctrl-single,pins = <
> + /* here we could enable to wakeup the cpu from suspend by a pen touch */
> + OMAP3_CORE1_IOPAD(0x2194, PIN_INPUT_PULLUP | MUX_MODE4) /* gpio160 */
> + >;
> + };
> };
>
> &omap3_pmx_core2 {
> @@ -410,10 +417,24 @@
> tsc2007@48 {
> compatible = "ti,tsc2007";
> reg = <0x48>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&penirq_pins>;
> interrupt-parent = <&gpio6>;
> interrupts = <0 IRQ_TYPE_EDGE_FALLING>; /* GPIO_160 */
> - gpios = <&gpio6 0 GPIO_ACTIVE_LOW>;
> - ti,x-plate-ohms = <600>;
> + gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* GPIO_160 */
> + touchscreen-size-x = <480>;
> + touchscreen-size-y = <640>;
> + touchscreen-max-pressure = <1000>;
> + touchscreen-fuzz-x = <3>;
> + touchscreen-fuzz-y = <8>;
> + touchscreen-fuzz-pressure = <10>;
> + touchscreen-inverted-y;
> + ti,min-x = <0x100>;
> + ti,max-x = <0xf00>;
> + ti,min-y = <0x100>;
> + ti,max-y = <0xf00>;
> + ti,max-rt = <4096>;
> + ti,x-plate-ohms = <550>;
> };
>
> /* RFID EEPROM */
> --
> 2.7.3
>
^ permalink raw reply
* Re: [PATCH v3 3/4] ARM: dts: am33xx: add DMA properties for tscadc
From: Tony Lindgren @ 2016-11-09 22:23 UTC (permalink / raw)
To: Jonathan Cameron
Cc: Mugunthan V N, linux-iio, Rob Herring, Mark Rutland, Russell King,
Hartmut Knaack, Lars-Peter Clausen, Peter Meerwald-Stadler,
Lee Jones, Vignesh R, Andrew F . Davis, linux-omap, devicetree,
linux-arm-kernel, linux-kernel, Sekhar Nori, Peter Ujfalusi,
John Syne
In-Reply-To: <1a339132-9dd9-6f29-dd66-3125f0e90555@kernel.org>
* Jonathan Cameron <jic23@kernel.org> [161105 10:35]:
> On 05/10/16 10:04, Mugunthan V N wrote:
> > Add DMA properties for tscadc
> >
> > Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
> The support in the driver is now working it's way through iio.git towards
> linux-next. I'm guessing this and the next patch will ultimately go through
> arm-soc.
>
> Shout if you'd rather I took them through the iio tree.
Applying the dts related patches 3 and 4 into omap-for-v4.10/dt thanks.
Tony
^ permalink raw reply
* Re: [PATCH 1/6] dt-bindings: mdio-mux: Add documentation for mdio mux for NSP SoC
From: Scott Branden @ 2016-11-09 22:23 UTC (permalink / raw)
To: Yendapally Reddy Dhananjaya Reddy, Rob Herring, Mark Rutland,
Russell King, Ray Jui, Scott Branden, Jon Mason, Florian Fainelli,
Kishon Vijay Abraham I
Cc: bcm-kernel-feedback-list, netdev, devicetree, linux-kernel,
linux-arm-kernel
In-Reply-To: <1478683994-12008-2-git-send-email-yendapally.reddy@broadcom.com>
One change
On 16-11-09 01:33 AM, Yendapally Reddy Dhananjaya Reddy wrote:
> Add documentation for mdio mux available in Broadcom NSP SoC
>
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
> ---
> .../devicetree/bindings/net/brcm,mdio-mux-nsp.txt | 57 ++++++++++++++++++++++
> 1 file changed, 57 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
>
> diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
> new file mode 100644
> index 0000000..b749a2b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
> @@ -0,0 +1,57 @@
> +Properties for an MDIO bus multiplexer available in Broadcom NSP SoC.
> +
> +This MDIO bus multiplexer defines buses that could access the internal
> +phys as well as external to SoCs. When child bus is selected, one needs
> +to select the below properties to generate desired MDIO transaction on
> +appropriate bus.
> +
> +Required properties in addition to the generic multiplexer properties:
> +
> +MDIO multiplexer node:
> +- compatible: brcm,mdio-mux-iproc.
This should be brcm,mdio-mux-nsp
> +- reg: Should contain registers location and length.
> +- reg-names: Should contain the resource reg names.
> + - bus-ctrl: mdio bus control register address space required to
> + select the bus master. This property is not required for SoC's
> + that doesn't provide master selection.
> + - mgmt-ctrl: mdio management control register address space
> +
> +Sub-nodes:
> + Each bus master should be represented as a sub-node.
> +
> +Sub-nodes required properties:
> +- reg: Bus master number. Should be 0x10 to access the external mdio devices.
> +- address-cells: should be 1
> +- size-cells: should be 0
> +
> +Every non-ethernet PHY requires a compatible property so that it could be
> +probed based on this compatible string.
> +
> +Additional information regarding generic multiplexer properties can be found
> +at- Documentation/devicetree/bindings/net/mdio-mux.txt
> +
> +example:
> +
> + mdio_mux: mdio-mux@3f190 {
> + compatible = "brcm,mdio-mux-nsp";
> + reg = <0x3f190 0x4>,
> + <0x32000 0x4>;
> + reg-names = "bus-ctrl", "mgmt-ctrl";
> + mdio-parent-bus = <&mdio>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + mdio@0 {
> + reg = <0x0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usb3_phy: usb3-phy@10 {
> + compatible = "brcm,nsp-usb3-phy";
> + reg = <0x10>;
> + usb3-ctrl-syscon = <&usb3_ctrl>;
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> + };
> + };
>
^ permalink raw reply
* Re: [PATCH v3 0/3] ARM: dts: omap5 uevm: add LEDs, USR1 button and EEPROM
From: Tony Lindgren @ 2016-11-09 22:03 UTC (permalink / raw)
To: H. Nikolaus Schaller
Cc: Benoît Cousson, Rob Herring, Mark Rutland, Russell King,
linux-omap, devicetree, linux-kernel, letux-kernel
In-Reply-To: <cover.1475126737.git.hns@goldelico.com>
* H. Nikolaus Schaller <hns@goldelico.com> [160928 22:26]:
> Changes V3:
> * remove unit addresses from LEDs [Rob Herring]
>
> 2016-09-28 20:08:23: Changes V2:
> * fixed subject of patches to correctly tell that it is for omap5 evm
> * changed default triggers a little to create a nicer default pattern
>
> 2016-09-27 07:26:14: These patches configure
> * the EEPROM
> * the LEDs (with some default triggers)
> * the USR1 gpio button
> for the OMAP5 UEVM board.
>
> H. Nikolaus Schaller (3):
> ARM: dts: omap5 uevm: add EEPROM
> ARM: dts: omap5 uevm: add LEDs
> ARM: dts: omap5 uevm: add USR1 button
Applying all into omap-for-v4.10/dt thanks.
Tony
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox