* Re: [PATCH 5/10] dt: bindings: Add bindings for Marvell Xenon SD Host Controller
From: Jisheng Zhang @ 2016-11-11 3:33 UTC (permalink / raw)
To: Ziji Hu, Rob Herring
Cc: Gregory CLEMENT, Ulf Hansson, Adrian Hunter, linux-mmc,
Jason Cooper, Andrew Lunn, Sebastian Hesselbarth, devicetree,
Thomas Petazzoni, linux-arm-kernel, Jack(SH) Zhu, Jimmy Xu,
Nadav Haklai, Ryan Gao, Doug Jones, Shiwu Zhang, Victor Gu,
Wei(SOCP) Liu, Wilson Ding, Xueping Liu, Hilbert
In-Reply-To: <20161111112243.7431625d@xhacker>
On Fri, 11 Nov 2016 11:22:43 +0800 Jisheng Zhang wrote:
> Hi Rob, Ziji,
>
> On Thu, 10 Nov 2016 19:44:19 +0800 Ziji Hu wrote:
>
> > Hi Rob,
> >
> > On 2016/11/10 2:24, Rob Herring wrote:
> > > On Mon, Oct 31, 2016 at 12:09:54PM +0100, Gregory CLEMENT wrote:
> > >> From: Ziji Hu <huziji@marvell.com>
> > >>
> > >> Marvell Xenon SDHC can support eMMC/SD/SDIO.
> > >> Add Xenon-specific properties.
> > >> Also add properties for Xenon PHY setting.
> > >>
> > >> Signed-off-by: Hu Ziji <huziji@marvell.com>
> > >> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
> > >> ---
> > >> Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt | 161 +++++++-
> > >> MAINTAINERS | 1 +-
> > >> 2 files changed, 162 insertions(+), 0 deletions(-)
> > >> create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> > >>
> > >> diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> > >> new file mode 100644
> > >> index 000000000000..0d2d139494d3
> > >> --- /dev/null
> > >> +++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> > >> @@ -0,0 +1,161 @@
> > >> +Marvell's Xenon SDHCI Controller device tree bindings
> > >> +This file documents differences between the core mmc properties
> > >> +described by mmc.txt and the properties used by the Xenon implementation.
> > >> +
> > >> +A single Xenon IP can support multiple slots.
> > >> +Each slot acts as an independent SDHC. It owns independent resources, such
> > >> +as register sets clock and PHY.
> > >> +Each slot should have an independent device tree node.
> > >> +
> > >> +Required Properties:
> > >> +- compatible: should be one of the following
> > >> + - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SOC.
> > >> + Must provide a second register area and marvell,pad-type.
> > >> + - "marvell,xenon-sdhci": For controllers on all the SOCs, other than
> > >> + Armada-3700.
> > >
> > > Need SoC specific compatible strings.
> > >
> >
> > Xenon SDHC is a common IP for all Marvell SOCs.
> > It is difficult to use a single SOC specific compatible to represent Xenon SDHC.
> > There will be so many SOC compatible strings in list if each specific SOC owns a compatible.
> > Actually only few SOCs require special properties.
> > Any suggestion please?
> >
> > >> +
> > >> +- clocks:
> > >> + Array of clocks required for SDHCI.
> > >> + Requires at least one for Xenon IP core.
> > >> + Some SOCs require additional clock for AXI bus.
> > >> +
> > >> +- clock-names:
> > >> + Array of names corresponding to clocks property.
> > >> + The input clock for Xenon IP core should be named as "core".
> > >> + The optional AXI clock should be named as "axi".
> > >
> > > When is AXI clock optional? This should be required for ?? compatible
> > > strings.
> > >
> > It is required on some SOCs.
> > I will double check if a suitable compatible string can be determined for those SOCs.
>
> Besides the core clk, berlin SoCs have one AXI clock. Usually, we have two
> solutions:
>
> solA: as current patch does, take "marvell,xenon-sdhci" as compatible string
> and make the AXI clock property optional. Usually for berlin SoCs, we don't need
> special properties.
Personally, I prefer solA: use the IP name as compatible string. This is IP
specific rather than SoC specific. The HW itself supports two clks
Thanks,
Jisheng
>
> PS: this solution is also what sdhci-pxav3.c takes
>
> solB: As Rob said, add extra SoC compatible strings, so we'll have
> something like:
>
> static const struct of_device_id sdhci_xenon_of_match[] = {
> { .compatible = "marvell,armada-3700-sdhci", },
> { .compatible = "marvell,berlin4ct-sdhci", },
> ...
> { .compatible = "marvell,berlinxxx-mmc", },
> }
>
> then we take care the AXI clk for berlin SoCs in the code.
>
>
> Which solution do you prefer?
>
> Thanks,
> Jisheng
^ permalink raw reply
* Re: [PATCH v4 0/3] Add clockevet for timer-nps driver to NPS400 SoC
From: Noam Camus @ 2016-11-11 3:28 UTC (permalink / raw)
To: robh+dt@kernel.org, mark.rutland@arm.com,
daniel.lezcano@linaro.org
Cc: tglx@linutronix.de, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
In-Reply-To: <1478454298-381-1-git-send-email-noamca@mellanox.com>
[-- Attachment #1: Type: text/plain, Size: 3086 bytes --]
Please comment on this series
Noam
________________________________
From: Noam Camus <noamca@mellanox.com>
Sent: Sunday, November 6, 2016 7:44:55 PM
To: robh+dt@kernel.org; mark.rutland@arm.com; daniel.lezcano@linaro.org
Cc: tglx@linutronix.de; devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; Noam Camus
Subject: [PATCH v4 0/3] Add clockevet for timer-nps driver to NPS400 SoC
From: Noam Camus <noamca@mellanox.com>
Change log
---
V3 --> V4
Main changes are [Thanks for the review]:
Fix many typos at log [Daniel]
Add handling for bad return values [Daniel and Thomas]
Replace use of internal irqchip pointers with existing IRQ API [Thomas]
Provide interrupt handler (percpu) with dev_id equal to evt [Thomas]
Fix passing *clk by reference to nps_get_timer_clk() [Daniel]
V2 --> V3
Apply Rob Herring comment about backword compatibility
V1 --> V2
Apply Daniel Lezcano comments:
CLOCKSOURCE_OF_DECLARE return value
update hotplug callbacks usage
squash of 2 first commits.
In this version I created new commit to serve as preperation for adding clockevents.
This way the last patch is more readable with clockevent content.
---
In first version of this driver we supported clocksource for the NPS400.
The support for clockevent was taken from Synopsys ARC timer driver.
This was good for working with our simulator of NPS400.
However in NPS400 ASIC the timers behave differently than simulation.
The timers in ASIC are shared between all threads whithin a core
and hence need different driver to support this behaviour.
The idea of this design is that we got 16 HW threads per core
each represented at bimask in a shared register in this core.
So when thread wants that next clockevent expiration will produce
timer interrupt to itself the correspondance bit in this register
should be set.
So theoretically if all 16 bits are set then all HW threads will get
timer interrupt on next expiration of timer 0.
Note that we use Synopsys ARC design naming convention for the timers
where:
timer0 is used for clockevents
timer1 is used for clocksource.
Noam Camus (3):
soc: Support for NPS HW scheduling
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
clocksource: Add clockevent support to NPS400 driver
.../bindings/timer/ezchip,nps400-timer.txt | 15 --
.../bindings/timer/ezchip,nps400-timer0.txt | 17 ++
.../bindings/timer/ezchip,nps400-timer1.txt | 15 ++
arch/arc/plat-eznps/include/plat/ctop.h | 2 -
drivers/clocksource/timer-nps.c | 264 ++++++++++++++++++--
include/soc/nps/mtm.h | 59 +++++
6 files changed, 335 insertions(+), 37 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/timer/ezchip,nps400-timer.txt
create mode 100644 Documentation/devicetree/bindings/timer/ezchip,nps400-timer0.txt
create mode 100644 Documentation/devicetree/bindings/timer/ezchip,nps400-timer1.txt
create mode 100644 include/soc/nps/mtm.h
[-- Attachment #2: Type: text/html, Size: 5066 bytes --]
^ permalink raw reply
* Re: [PATCH] phy: rockchip-inno-usb2: correct 480MHz output clock stable time
From: wlf @ 2016-11-11 3:23 UTC (permalink / raw)
To: Heiko Stübner
Cc: Doug Anderson, Kishon Vijay Abraham I,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
open list:ARM/Rockchip SoC...,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Rob Herring,
Frank Wang, 黄涛, Brian Norris, Guenter Roeck,
Matthias Kaehlcke, linux-clk
In-Reply-To: <2283070.Hkeafucara@diego>
Hi Heiko，
在 2016年11月10日 17:21, Heiko Stübner 写道:
> Am Donnerstag, 10. November 2016, 10:54:49 schrieb wlf:
>> Hi Doug,
>>
>> 在 2016年11月10日 04:54, Doug Anderson 写道:
>>> Hi,
>>>
>>> On Mon, Nov 7, 2016 at 5:00 AM, William Wu <wulf-TNX95d0MmH7DzftRWevZcw@public.gmane.org> wrote:
>>>> We found that the system crashed due to 480MHz output clock of
>>>> USB2 PHY was unstable after clock had been enabled by gpu module.
>>>>
>>>> Theoretically, 1 millisecond is a critical value for 480MHz
>>>> output clock stable time, so we try to change the delay time
>>>> to 1.2 millisecond to avoid this issue.
>>>>
>>>> Signed-off-by: William Wu <wulf-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>>>> ---
>>>>
>>>> drivers/phy/phy-rockchip-inno-usb2.c | 2 +-
>>>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>>>
>>>> diff --git a/drivers/phy/phy-rockchip-inno-usb2.c
>>>> b/drivers/phy/phy-rockchip-inno-usb2.c index ecfd7d1..8f2d2b6 100644
>>>> --- a/drivers/phy/phy-rockchip-inno-usb2.c
>>>> +++ b/drivers/phy/phy-rockchip-inno-usb2.c
>>>> @@ -267,7 +267,7 @@ static int rockchip_usb2phy_clk480m_enable(struct
>>>> clk_hw *hw)>>
>>>> return ret;
>>>>
>>>> /* waitting for the clk become stable */
>>>>
>>>> - mdelay(1);
>>>> + udelay(1200);
>>> Several people who have seen this patch have expressed concern that a
>>> 1.2 ms delay is pretty long for something that's supposed to be
>>> "atomic" like a clk_enable(). Consider that someone might call
>>> clk_enable() while interrupts are disabled and that a 1.2 ms interrupt
>>> latency is not so great.
>>>
>>> It seems like this clock should be moved to be enabled in "prepare"
>>> and the "enable" should be a no-op. This is a functionality change,
>>> but I don't think there are any real users for this clock at the
>>> moment so it should be fine.
>>>
>>> (of course, the 1 ms latency that existed before this patch was still
>>> pretty bad, but ...)
>> Thanks a lot for your suggestion.
>> I agree with you. clk_enable() will call spin_lock_irqsave() to disable
>> interrupt, and we add
>> more than 1ms in clk_enable may cause big latency.
>>
>> And according to clk_prepare() description:
>> In a simple case, clk_prepare can be used instead of clk_enable to
>> ungate a clk if the
>> operation may sleep. One example is a clk which is accessed over I2c.
>>
>> So maybe we can remove the clock to clk_prepare.
>>
>> Hi Heiko, Frank,
>> What do you think of it?
> moving to clk_prepare sounds sensible. That way you can switch from delay to
> sleep functions as well.
Thanks very much.
I will try to update a new patch.
Best regards,
Wulf
>
>
> Heiko
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH 5/10] dt: bindings: Add bindings for Marvell Xenon SD Host Controller
From: Jisheng Zhang @ 2016-11-11 3:22 UTC (permalink / raw)
To: Ziji Hu, Rob Herring
Cc: Gregory CLEMENT, Ulf Hansson, Adrian Hunter,
linux-mmc-u79uwXL29TY76Z2rM5mHXA, Jason Cooper, Andrew Lunn,
Sebastian Hesselbarth, devicetree-u79uwXL29TY76Z2rM5mHXA,
Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Jack(SH) Zhu,
Jimmy Xu, Nadav Haklai, Ryan Gao, Doug Jones, Shiwu Zhang,
Victor Gu, Wei(SOCP) Liu, Wilson Ding, Xueping Liu, Hilbert
In-Reply-To: <15b06a12-ed69-03a7-ccc7-0c133ce1ac1e-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
Hi Rob, Ziji,
On Thu, 10 Nov 2016 19:44:19 +0800 Ziji Hu wrote:
> Hi Rob,
>
> On 2016/11/10 2:24, Rob Herring wrote:
> > On Mon, Oct 31, 2016 at 12:09:54PM +0100, Gregory CLEMENT wrote:
> >> From: Ziji Hu <huziji-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
> >>
> >> Marvell Xenon SDHC can support eMMC/SD/SDIO.
> >> Add Xenon-specific properties.
> >> Also add properties for Xenon PHY setting.
> >>
> >> Signed-off-by: Hu Ziji <huziji-eYqpPyKDWXRBDgjK7y7TUQ@public.gmane.org>
> >> Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> >> ---
> >> Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt | 161 +++++++-
> >> MAINTAINERS | 1 +-
> >> 2 files changed, 162 insertions(+), 0 deletions(-)
> >> create mode 100644 Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> >> new file mode 100644
> >> index 000000000000..0d2d139494d3
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
> >> @@ -0,0 +1,161 @@
> >> +Marvell's Xenon SDHCI Controller device tree bindings
> >> +This file documents differences between the core mmc properties
> >> +described by mmc.txt and the properties used by the Xenon implementation.
> >> +
> >> +A single Xenon IP can support multiple slots.
> >> +Each slot acts as an independent SDHC. It owns independent resources, such
> >> +as register sets clock and PHY.
> >> +Each slot should have an independent device tree node.
> >> +
> >> +Required Properties:
> >> +- compatible: should be one of the following
> >> + - "marvell,armada-3700-sdhci": For controllers on Armada-3700 SOC.
> >> + Must provide a second register area and marvell,pad-type.
> >> + - "marvell,xenon-sdhci": For controllers on all the SOCs, other than
> >> + Armada-3700.
> >
> > Need SoC specific compatible strings.
> >
>
> Xenon SDHC is a common IP for all Marvell SOCs.
> It is difficult to use a single SOC specific compatible to represent Xenon SDHC.
> There will be so many SOC compatible strings in list if each specific SOC owns a compatible.
> Actually only few SOCs require special properties.
> Any suggestion please?
>
> >> +
> >> +- clocks:
> >> + Array of clocks required for SDHCI.
> >> + Requires at least one for Xenon IP core.
> >> + Some SOCs require additional clock for AXI bus.
> >> +
> >> +- clock-names:
> >> + Array of names corresponding to clocks property.
> >> + The input clock for Xenon IP core should be named as "core".
> >> + The optional AXI clock should be named as "axi".
> >
> > When is AXI clock optional? This should be required for ?? compatible
> > strings.
> >
> It is required on some SOCs.
> I will double check if a suitable compatible string can be determined for those SOCs.
Besides the core clk, berlin SoCs have one AXI clock. Usually, we have two
solutions:
solA: as current patch does, take "marvell,xenon-sdhci" as compatible string
and make the AXI clock property optional. Usually for berlin SoCs, we don't need
special properties.
PS: this solution is also what sdhci-pxav3.c takes
solB: As Rob said, add extra SoC compatible strings, so we'll have
something like:
static const struct of_device_id sdhci_xenon_of_match[] = {
{ .compatible = "marvell,armada-3700-sdhci", },
{ .compatible = "marvell,berlin4ct-sdhci", },
...
{ .compatible = "marvell,berlinxxx-mmc", },
}
then we take care the AXI clk for berlin SoCs in the code.
Which solution do you prefer?
Thanks,
Jisheng
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH V3 1/9] PM / OPP: Reword binding supporting multiple regulators per device
From: Viresh Kumar @ 2016-11-11 3:11 UTC (permalink / raw)
To: Stephen Boyd
Cc: Mark Brown, Rafael Wysocki, nm, Viresh Kumar, linaro-kernel,
linux-pm, linux-kernel, Vincent Guittot, robh, d-gerlach,
devicetree
In-Reply-To: <20161110225126.GK16026@codeaurora.org>
On 10-11-16, 14:51, Stephen Boyd wrote:
> On 11/10, Viresh Kumar wrote:
> > On 10-11-16, 16:36, Mark Brown wrote:
> > > On Thu, Nov 10, 2016 at 09:34:40AM +0530, Viresh Kumar wrote:
> > > > On 09-11-16, 14:58, Mark Brown wrote:
> > > > > On Wed, Oct 26, 2016 at 12:02:56PM +0530, Viresh Kumar wrote:
> > >
> > > > > > + Entries for multiple regulators shall be provided in the same field separated
> > > > > > + by angular brackets <>. The OPP binding doesn't provide any provisions to
> > > > > > + relate the values to their power supplies or the order in which the supplies
> > > > > > + need to be configured.
> > >
> > > > > I don't understand how this works. If we have an unordered list of
> > > > > values to set for regulators how will we make sense of them?
> > >
> > > > The platform driver is responsible to identify the order and pass it on to the
> > > > OPP core. And the platform driver needs to have that hard coded.
> > >
> > > That *really* should be in the binding.
> >
> > Okay, how do you suggest doing that? Will a property like supply-names
> > in the OPP table be fine? Like this:
> >
> > @@ -369,13 +378,16 @@ Example 4: Handling multiple regulators
> > compatible = "arm,cortex-a7";
> > ...
> >
> > - cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>;
> > + vcc0-supply = <&cpu_supply0>;
> > + vcc1-supply = <&cpu_supply1>;
> > + vcc2-supply = <&cpu_supply2>;
> > operating-points-v2 = <&cpu0_opp_table>;
> > };
> > };
> >
> > cpu0_opp_table: opp_table0 {
> > compatible = "operating-points-v2";
> > + supply-names = "vcc0", "vcc1", "vcc2";
> > opp-shared;
> >
>
> No. The supply names (and also clock names/index) should be left
> up to the consumer of the OPP table. We don't want to encode any
> sort of details like this between the OPP table and the consumer
> of it in DT because then it seriously couples the OPP table to
> the consumer device. "The binding" in this case that needs to be
> updated is the consumer binding, to indicate that it correlated
> foo-supply and bar-supply to index 0 and 1 of the OPP table
> voltages.
Are you saying that we shall have a property like this then?
diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt
index ee91cbdd95ee..733946df2fb8 100644
--- a/Documentation/devicetree/bindings/opp/opp.txt
+++ b/Documentation/devicetree/bindings/opp/opp.txt
@@ -389,7 +389,10 @@ Example 4: Handling multiple regulators
compatible = "arm,cortex-a7";
...
- cpu-supply = <&cpu_supply0>, <&cpu_supply1>, <&cpu_supply2>;
+ vcc0-supply = <&cpu_supply0>;
+ vcc1-supply = <&cpu_supply1>;
+ vcc2-supply = <&cpu_supply2>;
+ opp-supply-names = "vcc0", "vcc1", "vcc2";
operating-points-v2 = <&cpu0_opp_table>;
};
};
--
viresh
^ permalink raw reply related
* Re: [PATCH v5 02/23] of: device: Export of_device_{get_modalias, uvent_modalias} to modules
From: Chen-Yu Tsai @ 2016-11-11 3:01 UTC (permalink / raw)
To: Rob Herring
Cc: Chen-Yu Tsai, Peter Chen, Stephen Boyd, Greg KH, Arnd Bergmann,
Neil Armstrong, linux-arm-msm, linux-usb, linux-kernel,
Bjorn Andersson, Peter Chen, linux-arm-kernel, Andy Gross,
devicetree, Felipe Balbi
In-Reply-To: <CAL_Jsq+Bw4XVEJY6V4Hn+D_OmqEcp_nLLrVT0_i+jX_guCqzfA@mail.gmail.com>
On Fri, Nov 11, 2016 at 5:42 AM, Rob Herring <robh@kernel.org> wrote:
> On Sun, Nov 6, 2016 at 7:56 PM, Chen-Yu Tsai <wens@csie.org> wrote:
>> On Mon, Nov 7, 2016 at 9:29 AM, Peter Chen <hzpeterchen@gmail.com> wrote:
>>> On Fri, Nov 04, 2016 at 01:51:34PM -0700, Stephen Boyd wrote:
>>>> Quoting Peter Chen (2016-10-24 18:16:32)
>>>> > On Mon, Oct 24, 2016 at 12:48:24PM -0700, Stephen Boyd wrote:
>>>> > > Quoting Chen-Yu Tsai (2016-10-24 05:19:05)
>>>> > > > Hi,
>>>> > > >
>>>> > > > On Tue, Oct 18, 2016 at 9:56 AM, Stephen Boyd <stephen.boyd@linaro.org> wrote:
>>>> > > > > The ULPI bus can be built as a module, and it will soon be
>>>> > > > > calling these functions when it supports probing devices from DT.
>>>> > > > > Export them so they can be used by the ULPI module.
>>>> > > > >
>>>> > > > > Acked-by: Rob Herring <robh@kernel.org>
>>>> > > > > Cc: <devicetree@vger.kernel.org>
>>>> > > > > Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
>>>> > > > > ---
>>>> > > > > drivers/of/device.c | 2 ++
>>>> > > > > 1 file changed, 2 insertions(+)
>>>> > > > >
>>>> > > > > diff --git a/drivers/of/device.c b/drivers/of/device.c
>>>> > > > > index 8a22a253a830..6719ab35b62e 100644
>>>> > > > > --- a/drivers/of/device.c
>>>> > > > > +++ b/drivers/of/device.c
>>>> > > > > @@ -225,6 +225,7 @@ ssize_t of_device_get_modalias(struct device *dev, char *str, ssize_t len)
>>>> > > > >
>>>> > > > > return tsize;
>>>> > > > > }
>>>> > > > > +EXPORT_SYMBOL_GPL(of_device_get_modalias);
>>>> > > > >
>>>> > > > > int of_device_request_module(struct device *dev)
>>>> > > > > {
>>>> > > > > @@ -290,6 +291,7 @@ void of_device_uevent(struct device *dev, struct kobj_uevent_env *env)
>>>> > > > > }
>>>> > > > > mutex_unlock(&of_mutex);
>>>> > > > > }
>>>> > > > > +EXPORT_SYMBOL_GPL(of_device_uevent_modalias);
>>>> > > >
>>>> > > > This is trailing the wrong function.
>>>> > > >
>>>> > >
>>>> > > Good catch. Must have been some bad rebase.
>>>> > >
>>>> > > Peter, can you fix it while applying or should I resend this patch?
>>>> > >
>>>> >
>>>> > But, this is device tree patch. I can only get chipidea part and other
>>>> > USB patches if Greg agrees.
>>>> >
>>>>
>>>> Were you expecting Rob to take the drivers/of/* patches? Sorry I thought
>>>> Rob acked them so they could go through usb with the other changes.
>>>
>>> I am just worried about possible merge error when linus pulls both OF
>>> and USB tree. Greg, is it ok the OF patches through USB tree with OF
>>> maintainer's ack?
>>
>> May I suggest putting the OF patches on an immutable branch so other
>> subsystems can pull them in without pulling in the USB patches? At
>> least I want to use them in the I2C subsystem, and in the sunxi-rsb
>> driver.
>
> Do you have patches using this already. If not, it is starting to get
> a bit late for v4.10.
>
> I can apply this, but then you'll just be pulling in other DT patches.
Not sure what you mean by "using" this...
I have patches which use this to add DT-based modalias entries for
module auto-loading to i2c and sunxi-rsb that I haven't sent.
As far as DT usage goes, we already need this for the axp20x mfd driver.
There are 2 variants, i2c and sunxi-rsb. For the I2C variant a fix was
sent to fix module auto-loading by using the I2C client ID table:
mfd: axp20x-i2c: Add i2c-ids to fix module auto-loading
https://git.kernel.org/cgit/linux/kernel/git/lee/mfd.git/commit/?h=for-mfd-next&id=b7142a19321484bd7681aa547c1d50148c8e2825
But for the sunxi-rsb variant such a fix does not exist, as the bus
does not have a separate ID table. It uses DT exclusively.
Regards
ChenYu
^ permalink raw reply
* Re: [PATCH v3 12/17] ASoC: simple-card-utils: add asoc_simple_card_try_to_probe_graph_card()
From: kbuild test robot @ 2016-11-11 2:07 UTC (permalink / raw)
To: Kuninori Morimoto
Cc: kbuild-all, Rob Herring, Mark Brown, Linux-ALSA, Liam Girdwood,
Simon, Laurent, Guennadi, Grant Likely, Frank Rowand, Linux-DT,
Linux-Kernel
In-Reply-To: <87eg2ireua.wl%kuninori.morimoto.gx@renesas.com>
[-- Attachment #1: Type: text/plain, Size: 1737 bytes --]
Hi Kuninori,
[auto build test ERROR on asoc/for-next]
[also build test ERROR on v4.9-rc4 next-20161110]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Kuninori-Morimoto/ASoC-add-OF-graph-base-simple-card/20161111-093231
base: https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git for-next
config: x86_64-randconfig-x010-201645 (attached as .config)
compiler: gcc-6 (Debian 6.2.0-3) 6.2.0 20160901
reproduce:
# save the attached .config to linux build tree
make ARCH=x86_64
All error/warnings (new ones prefixed by >>):
sound/soc/generic/simple-card-utils.c: In function 'asoc_simple_card_try_to_probe_graph_card':
>> sound/soc/generic/simple-card-utils.c:297:9: error: implicit declaration of function 'of_graph_get_top_port' [-Werror=implicit-function-declaration]
node = of_graph_get_top_port(dev);
^~~~~~~~~~~~~~~~~~~~~
>> sound/soc/generic/simple-card-utils.c:297:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
node = of_graph_get_top_port(dev);
^
cc1: some warnings being treated as errors
vim +/of_graph_get_top_port +297 sound/soc/generic/simple-card-utils.c
291 {
292 struct platform_device_info pdevinfo;
293 struct device_node *node;
294 const char *compatible;
295 int ret;
296
> 297 node = of_graph_get_top_port(dev);
298 if (!node || !info)
299 /*
300 * It doesn't have graph base sound DT, or its infomation.
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 23944 bytes --]
^ permalink raw reply
* Re: [PATCH v9 2/8] power: add power sequence library
From: Peter Chen @ 2016-11-11 1:53 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Peter Chen, Greg Kroah-Hartman, Alan Stern, Ulf Hansson,
Mark Brown, Sebastian Reichel, Rob Herring, Shawn Guo,
Rafael J. Wysocki, Dmitry Eremin-Solenikov, Heiko Stuebner,
linux-arm-kernel@lists.infradead.org, p.zabel,
devicetree@vger.kernel.org, Pawel Moll, Mark Rutland,
open list:ULTRA-WIDEBAND (UWB) SUBSYSTEM:, Arnd Bergmann
In-Reply-To: <CAJZ5v0ioqMqoaJqK0CTXafWRKoohmZSiOWKRgVZ9DR3_8+-YDw@mail.gmail.com>
On Fri, Nov 11, 2016 at 02:05:01AM +0100, Rafael J. Wysocki wrote:
> On Tue, Nov 8, 2016 at 3:51 AM, Peter Chen <peter.chen@nxp.com> wrote:
> > We have an well-known problem that the device needs to do some power
> > sequence before it can be recognized by related host, the typical
> > example like hard-wired mmc devices and usb devices.
> >
> > This power sequence is hard to be described at device tree and handled by
> > related host driver, so we have created a common power sequence
> > library to cover this requirement. The core code has supplied
> > some common helpers for host driver, and individual power sequence
> > libraries handle kinds of power sequence for devices. The pwrseq
> > librares always need to allocate extra instance for compatible
> > string match.
> >
> > pwrseq_generic is intended for general purpose of power sequence, which
> > handles gpios and clocks currently, and can cover other controls in
> > future. The host driver just needs to call of_pwrseq_on/of_pwrseq_off
> > if only one power sequence is needed, else call of_pwrseq_on_list
> > /of_pwrseq_off_list instead (eg, USB hub driver).
> >
> > For new power sequence library, it can add its compatible string
> > to pwrseq_of_match_table, then the pwrseq core will match it with
> > DT's, and choose this library at runtime.
>
> In the first place, please document this stuff better than you have so
> far. To a minimum, add kerneldoc comments to all new non-trivial new
> functions to document what they are for and how they are expected to
> be used (especially the ones exported to drivers).
>
Thanks for your comments.
I will add kerneldoc for main APIs.
> Also, is there any guidance available for people who may want to use it?
No doc now, only some guidance in this commit log.
> > +config PWRSEQ_GENERIC
> > + bool "Generic power sequence control"
> > + depends on OF
> > + select POWER_SEQUENCE
> > + help
> > + It is used for drivers which needs to do power sequence
> > + (eg, turn on clock, toggle reset gpio) before the related
> > + devices can be found by hardware. This generic one can be
> > + used for common power sequence control.
>
> I wouldn't set it up this way.
>
> There are two problems here.
>
> First, say a distro is going to ship a multiplatform generic kernel.
> How they are going to figure out whether or not to set the new symbol
> in that kernel?
>
> Second, how users are supposed to know whether or not they will need
> it even if they build the kernel by themselves?
>
> It would be better IMO to set things up to select the new symbol from
> places making use of the code depending on it.
>
Will change it like below:
#
# Power Sequence library
#
menuconfig POWER_SEQUENCE
bool "Power sequence control"
depends on OF
help
It is used for drivers which needs to do power sequence
(eg, turn on clock, toggle reset gpio) before the related
devices can be found by hardware.
if POWER_SEQUENCE
config PWRSEQ_GENERIC
bool "Generic power sequence control"
default y
help
This is the generic power sequence control library, and is
supposed to support common power sequence usage.
endif
And the current user usb core will select POWER_SEQUENCE.
--
Best Regards,
Peter Chen
^ permalink raw reply
* [PATCH v3 17/17] ASoC: add simple-graph-scu-card support
From: Kuninori Morimoto @ 2016-11-11 1:25 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
graph base DT binding are used on V4L2, and ALSA SoC is using different
style of DT. In case of simple case, ALSA SoC supports simple-card
driver.
In the future, V4L2 / ALSA will support HDMI, and then, DT bindings
between V4L2 / ALSA should be merged somehow.
Sometimes, we would like to use DPCM base simple-card on graph base DT.
This patch adds graph base DT binding of simple-scu-card
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
sound/soc/generic/Kconfig | 8 +
sound/soc/generic/Makefile | 2 +
sound/soc/generic/simple-graph-scu-card.c | 417 ++++++++++++++++++++++++++++++
3 files changed, 427 insertions(+)
create mode 100644 sound/soc/generic/simple-graph-scu-card.c
diff --git a/sound/soc/generic/Kconfig b/sound/soc/generic/Kconfig
index efefabd..fc11828 100644
--- a/sound/soc/generic/Kconfig
+++ b/sound/soc/generic/Kconfig
@@ -21,3 +21,11 @@ config SND_SIMPLE_GRAPH_CARD
select SND_SIMPLE_CARD_UTILS
help
This option enables generic simple Graph sound card support
+
+config SND_SIMPLE_GRAPH_SCU_CARD
+ tristate "ASoC Simple Graph SCU sound card support"
+ depends on OF
+ select SND_SIMPLE_CARD_UTILS
+ help
+ This option enables generic simple Graph SCU sound card support.
+ It supports DPCM of multi CPU single Codec ststem.
diff --git a/sound/soc/generic/Makefile b/sound/soc/generic/Makefile
index 94eb6f1..fd75b55 100644
--- a/sound/soc/generic/Makefile
+++ b/sound/soc/generic/Makefile
@@ -2,8 +2,10 @@ snd-soc-simple-card-utils-objs := simple-card-utils.o
snd-soc-simple-card-objs := simple-card.o
snd-soc-simple-scu-card-objs := simple-scu-card.o
snd-soc-simple-graph-card-objs := simple-graph-card.o
+snd-soc-simple-graph-scu-card-objs := simple-graph-scu-card.o
obj-$(CONFIG_SND_SIMPLE_CARD_UTILS) += snd-soc-simple-card-utils.o
obj-$(CONFIG_SND_SIMPLE_CARD) += snd-soc-simple-card.o
obj-$(CONFIG_SND_SIMPLE_SCU_CARD) += snd-soc-simple-scu-card.o
obj-$(CONFIG_SND_SIMPLE_GRAPH_CARD) += snd-soc-simple-graph-card.o
+obj-$(CONFIG_SND_SIMPLE_GRAPH_SCU_CARD) += snd-soc-simple-graph-scu-card.o
diff --git a/sound/soc/generic/simple-graph-scu-card.c b/sound/soc/generic/simple-graph-scu-card.c
new file mode 100644
index 0000000..39a5019
--- /dev/null
+++ b/sound/soc/generic/simple-graph-scu-card.c
@@ -0,0 +1,417 @@
+/*
+ * ASoC simple graph SCU sound card support
+ *
+ * Copyright (C) 2016 Renesas Solutions Corp.
+ * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
+ *
+ * based on
+ * ${LINUX}/sound/soc/generic/simple-graph-card.c
+ * ${LINUX}/sound/soc/generic/simple-scu-card.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <sound/jack.h>
+#include <sound/simple_card_utils.h>
+
+struct simple_card_data {
+ struct snd_soc_card snd_card;
+ struct snd_soc_codec_conf codec_conf;
+ struct asoc_simple_dai *dai_props;
+ struct snd_soc_dai_link *dai_link;
+ u32 convert_rate;
+ u32 convert_channels;
+};
+
+#define simple_priv_to_dev(priv) ((priv)->snd_card.dev)
+#define simple_priv_to_link(priv, i) ((priv)->snd_card.dai_link + (i))
+#define simple_priv_to_props(priv, i) ((priv)->dai_props + (i))
+
+#define PREFIX "simple-audio-card,"
+
+static int asoc_simple_card_startup(struct snd_pcm_substream *substream)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct asoc_simple_dai *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+
+ return clk_prepare_enable(dai_props->clk);
+}
+
+static void asoc_simple_card_shutdown(struct snd_pcm_substream *substream)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct asoc_simple_dai *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+
+ clk_disable_unprepare(dai_props->clk);
+}
+
+static struct snd_soc_ops asoc_simple_card_ops = {
+ .startup = asoc_simple_card_startup,
+ .shutdown = asoc_simple_card_shutdown,
+};
+
+static int asoc_simple_card_dai_init(struct snd_soc_pcm_runtime *rtd)
+{
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct snd_soc_dai *dai;
+ struct snd_soc_dai_link *dai_link;
+ struct asoc_simple_dai *dai_props;
+ int num = rtd->num;
+
+ dai_link = simple_priv_to_link(priv, num);
+ dai_props = simple_priv_to_props(priv, num);
+ dai = dai_link->dynamic ?
+ rtd->cpu_dai :
+ rtd->codec_dai;
+
+ return asoc_simple_card_init_dai(dai, dai_props);
+}
+
+static int asoc_simple_card_be_hw_params_fixup(struct snd_soc_pcm_runtime *rtd,
+ struct snd_pcm_hw_params *params)
+{
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct snd_interval *rate = hw_param_interval(params,
+ SNDRV_PCM_HW_PARAM_RATE);
+ struct snd_interval *channels = hw_param_interval(params,
+ SNDRV_PCM_HW_PARAM_CHANNELS);
+
+ if (priv->convert_rate)
+ rate->min =
+ rate->max = priv->convert_rate;
+
+ if (priv->convert_channels)
+ channels->min =
+ channels->max = priv->convert_channels;
+
+ return 0;
+}
+
+static int asoc_simple_card_dai_link_of(struct device_node *port,
+ struct device_node *ep,
+ struct simple_card_data *priv,
+ unsigned int daifmt,
+ int idx, int is_fe)
+{
+ struct device *dev = simple_priv_to_dev(priv);
+ struct snd_soc_dai_link *dai_link = simple_priv_to_link(priv, idx);
+ struct asoc_simple_dai *dai_props = simple_priv_to_props(priv, idx);
+ int ret;
+
+ if (is_fe) {
+ /* BE is dummy */
+ dai_link->codec_of_node = NULL;
+ dai_link->codec_dai_name = "snd-soc-dummy-dai";
+ dai_link->codec_name = "snd-soc-dummy";
+
+ /* FE settings */
+ dai_link->dynamic = 1;
+ dai_link->dpcm_merged_format = 1;
+
+ ret = asoc_simple_card_parse_graph_cpu(ep, dai_link);
+ if (ret)
+ return ret;
+
+ ret = asoc_simple_card_parse_clk_cpu(ep, dai_link, dai_props);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_set_dailink_name(dev, dai_link,
+ "fe.%s",
+ dai_link->cpu_dai_name);
+ if (ret < 0)
+ return ret;
+
+ /* snd_card.num_links includes Codec */
+ asoc_simple_card_canonicalize_cpu(dai_link,
+ (priv->snd_card.num_links -1) == 1);
+ } else {
+ /* FE is dummy */
+ dai_link->cpu_of_node = NULL;
+ dai_link->cpu_dai_name = "snd-soc-dummy-dai";
+ dai_link->cpu_name = "snd-soc-dummy";
+
+ /* BE settings */
+ dai_link->no_pcm = 1;
+ dai_link->be_hw_params_fixup = asoc_simple_card_be_hw_params_fixup;
+
+ ret = asoc_simple_card_parse_graph_codec(ep, dai_link);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_parse_clk_codec(ep, dai_link, dai_props);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_set_dailink_name(dev, dai_link,
+ "be.%s",
+ dai_link->codec_dai_name);
+ if (ret < 0)
+ return ret;
+
+ snd_soc_of_parse_audio_prefix_from_node(&priv->snd_card,
+ port,
+ &priv->codec_conf,
+ dai_link->codec_of_node,
+ PREFIX "prefix");
+ }
+
+ ret = snd_soc_of_parse_tdm_slot(ep,
+ &dai_props->tx_slot_mask,
+ &dai_props->rx_slot_mask,
+ &dai_props->slots,
+ &dai_props->slot_width);
+ if (ret)
+ return ret;
+
+ ret = asoc_simple_card_canonicalize_dailink(dai_link);
+ if (ret < 0)
+ return ret;
+
+ dai_link->dai_fmt = daifmt;
+ dai_link->dpcm_playback = 1;
+ dai_link->dpcm_capture = 1;
+ dai_link->ops = &asoc_simple_card_ops;
+ dai_link->init = asoc_simple_card_dai_init;
+
+ dev_dbg(dev, "\t%s / %04x / %d\n",
+ dai_link->name,
+ dai_link->dai_fmt,
+ dai_props->sysclk);
+
+ return 0;
+}
+
+static int asoc_simple_card_parse_of(struct device_node *node,
+ struct simple_card_data *priv)
+{
+ struct device *dev = simple_priv_to_dev(priv);
+ struct device *cpu_dev = dev->parent;
+ struct device_node *ports = of_graph_get_top_port(cpu_dev);
+ struct snd_soc_card *card = &priv->snd_card;
+ struct device_node *port, *cpu_ep, *r_cpu_ep, *codec_ep;
+ unsigned int daifmt = 0;
+ int i, ret, done;
+
+ if (!node)
+ return -EINVAL;
+
+ ret = snd_soc_of_parse_audio_routing_from_node(&priv->snd_card,
+ ports, PREFIX "routing");
+ if (ret)
+ return ret;
+
+ /* sampling rate convert */
+ of_property_read_u32(ports, PREFIX "convert-rate",
+ &priv->convert_rate);
+
+ /* channels transfer */
+ of_property_read_u32(ports, PREFIX "convert-channels",
+ &priv->convert_channels);
+
+ /*
+ * it supports multi CPU, single CODEC only here.
+ */
+
+ /* find 1st codec */
+ done = 0;
+ for_each_of_port(node, port) {
+ /* keep for_each for of_node_get/of_node_put */
+ if (done)
+ continue;
+
+ for_each_of_endpoint_in_port(port, cpu_ep) {
+ /* keep for_each for of_node_get/of_node_put */
+ if (done)
+ continue;
+
+ codec_ep = of_graph_get_remote_endpoint(cpu_ep);
+ r_cpu_ep = of_graph_get_remote_endpoint(codec_ep);
+ of_node_put(codec_ep);
+ of_node_put(r_cpu_ep);
+ if (cpu_ep != r_cpu_ep) {
+ ret = -EINVAL;
+ goto parse_of_err;
+ }
+
+ ret = asoc_simple_card_parse_daifmt(dev,
+ ports, codec_ep,
+ PREFIX, &daifmt);
+ if (ret < 0)
+ goto parse_of_err;
+
+ done = 1;
+ }
+ }
+
+ /* Front-End (= CPU) */
+ i = 0;
+ for_each_of_port(node, port) {
+ for_each_of_endpoint_in_port(port, cpu_ep) {
+ ret = asoc_simple_card_dai_link_of(
+ port, cpu_ep, priv, daifmt, i, 1);
+ if (ret < 0)
+ goto parse_of_err;
+ i++;
+ }
+ }
+
+ /* Back-End (= Codec) */
+ done = 0;
+ for_each_of_port(node, port) {
+ /* keep for_each for of_node_get/of_node_put */
+ if (done)
+ continue;
+
+ for_each_of_endpoint_in_port(port, cpu_ep) {
+ /* keep for_each for of_node_get/of_node_put */
+ if (done)
+ continue;
+
+ codec_ep = of_graph_get_remote_endpoint(cpu_ep);
+ r_cpu_ep = of_graph_get_remote_endpoint(codec_ep);
+ of_node_put(codec_ep);
+ of_node_put(r_cpu_ep);
+ if (cpu_ep != r_cpu_ep) {
+ ret = -EINVAL;
+ goto parse_of_err;
+ }
+
+ ret = asoc_simple_card_dai_link_of(
+ port, codec_ep, priv, daifmt, i, 0);
+ if (ret < 0)
+ goto parse_of_err;
+ i++;
+
+ done = 1;
+ }
+ }
+
+ ret = asoc_simple_card_parse_card_name(card, ports, PREFIX);
+ if (ret)
+ return ret;
+
+ dev_dbg(dev, "New card: %s\n",
+ priv->snd_card.name ? priv->snd_card.name : "");
+ dev_dbg(dev, "convert_rate %d\n", priv->convert_rate);
+ dev_dbg(dev, "convert_channels %d\n", priv->convert_channels);
+
+ return 0;
+parse_of_err:
+ of_node_put(port);
+ of_node_put(cpu_ep);
+
+ return ret;
+}
+
+static int asoc_simple_card_probe(struct platform_device *pdev)
+{
+ struct simple_card_data *priv;
+ struct snd_soc_dai_link *dai_link;
+ struct asoc_simple_dai *dai_props;
+ struct device *dev = &pdev->dev;
+ struct device *cpu_dev = pdev->dev.parent;
+ struct device_node *cpu_node = cpu_dev->of_node;
+ struct asoc_simple_graph_card_info *info = pdev->dev.platform_data;
+ int num, ret;
+
+ /* Allocate the private data and the DAI link array */
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ /* it supports multi CPU, single CODEC only here */
+ num = info->endpoint_num + 1; /* +1 for Codec */
+
+ dai_props = devm_kzalloc(dev, sizeof(*dai_props) * num, GFP_KERNEL);
+ dai_link = devm_kzalloc(dev, sizeof(*dai_link) * num, GFP_KERNEL);
+ if (!dai_props || !dai_link)
+ return -ENOMEM;
+
+ priv->dai_props = dai_props;
+ priv->dai_link = dai_link;
+
+ /* Init snd_soc_card */
+ priv->snd_card.owner = THIS_MODULE;
+ priv->snd_card.dev = dev;
+ priv->snd_card.dai_link = priv->dai_link;
+ priv->snd_card.num_links = num;
+ priv->snd_card.codec_conf = &priv->codec_conf;
+ priv->snd_card.num_configs = 1;
+
+ ret = asoc_simple_card_parse_of(cpu_node, priv);
+ if (ret < 0) {
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "parse error %d\n", ret);
+ goto err;
+ }
+
+ /*
+ * FIXME
+ *
+ * This driver is assuming that it will be called from
+ * asoc_simple_card_try_to_probe_graph_card() which
+ * is using platform_device_register_full().
+ * This means it is not came from DT. But this driver itself
+ * will be used as part of ALSA SoC (= sound card).
+ * Because of these background, it might fail in
+ * snd_pcm_lib_malloc_pages() on .hw_params.
+ * Because, noone cares its dma_ops, and result of get_dma_ops()
+ * is based on its architecture.
+ * So, it should call arch_setup_dma_ops() from somewhere,
+ * otherwise, for example, ARM is no problem, but ARM64 will be fail.
+ * But, of_platform_device_xxx() are not good solution today.
+ * This driver calls it by itself here. Please fixme
+ * see also
+ * linux/sound/soc/generic/simple-card-utils.c ::
+ * asoc_simple_card_try_to_probe_graph_card()
+ */
+ of_dma_configure(dev, dev->of_node);
+
+ snd_soc_card_set_drvdata(&priv->snd_card, priv);
+
+ ret = devm_snd_soc_register_card(dev, &priv->snd_card);
+ if (ret >= 0)
+ return ret;
+err:
+ asoc_simple_card_clean_reference(&priv->snd_card);
+
+ return ret;
+}
+
+static int asoc_simple_card_remove(struct platform_device *pdev)
+{
+ struct snd_soc_card *card = platform_get_drvdata(pdev);
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(card);
+
+ return asoc_simple_card_clean_reference(&priv->snd_card);
+}
+
+static struct platform_driver asoc_simple_card = {
+ .driver = {
+ .name = "asoc-simple-graph-scu-card",
+ },
+ .probe = asoc_simple_card_probe,
+ .remove = asoc_simple_card_remove,
+};
+module_platform_driver(asoc_simple_card);
+
+MODULE_ALIAS("platform:asoc-simple-graph-scu-card");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("ASoC Simple Graph SCU Sound Card");
+MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");
--
1.9.1
^ permalink raw reply related
* [PATCH v3 16/17] ASoC: add simple-graph-scu-card document
From: Kuninori Morimoto @ 2016-11-11 1:24 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- Added how to use Simple-Graph-SCU-Card, and cleaned-up
.../bindings/sound/simple-graph-scu-card.txt | 65 ++++++++++++++++++++++
1 file changed, 65 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/simple-graph-scu-card.txt
diff --git a/Documentation/devicetree/bindings/sound/simple-graph-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-graph-scu-card.txt
new file mode 100644
index 0000000..223096a
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/simple-graph-scu-card.txt
@@ -0,0 +1,65 @@
+Simple-Graph-SCU-Card:
+
+Simple-Graph-SCU-Card specifies audio DAI connections of SoC <-> codec.
+It is based on common bindings for device graphs.
+see ${LINUX}/Documentation/devicetree/bindings/graph.txt
+
+Basically, Simple-Graph-SCU-Card property is same as Simple-Card / Simple-Graph-Card.
+see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt
+ ${LINUX}/Documentation/devicetree/bindings/sound/simple-graph-card.txt
+
+Main difference between Simple-Graph-Card and Simple-Graph-SCU-Card is that
+Simple-Graph-SCU-Card can use multi CPU.
+
+Required properties:
+
+- compatible : "asoc-simple-graph-scu-card";
+- simple-audio-card,routing : see simple-card.txt
+
+Example
+
+ak4643: codec@12 {
+ compatible = "asahi-kasei,ak4643";
+ ...
+ port {
+ ak4643_fe: endpoint@0 {
+ remote-endpoint = <&rsnd_fe>;
+ ...
+ };
+ ak4643_be: endpoint@1 {
+ remote-endpoint = <&rsnd_be>;
+ ...
+ };
+ };
+};
+
+rcar_sound {
+ ...
+ ports {
+ compatible = "asoc-simple-graph-scu-card";
+
+ simple-audio-card,name = "graph-sound";
+ simple-audio-card,format = "left_j";
+ simple-audio-card,bitclock-master = <&rsnd_fe>;
+ simple-audio-card,frame-master = <&rsnd_fe>;
+ simple-audio-card,convert-rate = <48000>;
+ simple-audio-card,convert-channels = <2>;
+ simple-audio-card,prefix = "ak4642";
+ simple-audio-card,routing =
+ "ak4642 Playback", "DAI0 Playback",
+ "ak4642 Playback", "DAI1 Playback";
+
+ port@0 {
+ rsnd_fe: endpoint@0 {
+ remote-endpoint = <&ak4643_fe>;
+ ...
+ };
+ };
+ port@1 {
+ rsnd_be: endpoint@1 {
+ remote-endpoint = <&ak4643_be>;
+ ...
+ };
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related
* [PATCH v3 15/17] ASoC: add simple-graph-card support
From: Kuninori Morimoto @ 2016-11-11 1:24 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
graph base DT binding are used on V4L2, and ALSA SoC is using different
style of DT. In case of simple case, ALSA SoC supports simple-card
driver.
In the future, V4L2 / ALSA will support HDMI, and then, DT bindings
between V4L2 / ALSA should be merged somehow.
This patch adds graph base DT binding with simple-card style
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
sound/soc/generic/Kconfig | 7 +
sound/soc/generic/Makefile | 2 +
sound/soc/generic/simple-graph-card.c | 462 ++++++++++++++++++++++++++++++++++
3 files changed, 471 insertions(+)
create mode 100644 sound/soc/generic/simple-graph-card.c
diff --git a/sound/soc/generic/Kconfig b/sound/soc/generic/Kconfig
index d023959..efefabd 100644
--- a/sound/soc/generic/Kconfig
+++ b/sound/soc/generic/Kconfig
@@ -14,3 +14,10 @@ config SND_SIMPLE_SCU_CARD
help
This option enables generic simple SCU sound card support.
It supports DPCM of multi CPU single Codec system.
+
+config SND_SIMPLE_GRAPH_CARD
+ tristate "ASoC Simple Graph sound card support"
+ depends on OF
+ select SND_SIMPLE_CARD_UTILS
+ help
+ This option enables generic simple Graph sound card support
diff --git a/sound/soc/generic/Makefile b/sound/soc/generic/Makefile
index ee750f3..94eb6f1 100644
--- a/sound/soc/generic/Makefile
+++ b/sound/soc/generic/Makefile
@@ -1,7 +1,9 @@
snd-soc-simple-card-utils-objs := simple-card-utils.o
snd-soc-simple-card-objs := simple-card.o
snd-soc-simple-scu-card-objs := simple-scu-card.o
+snd-soc-simple-graph-card-objs := simple-graph-card.o
obj-$(CONFIG_SND_SIMPLE_CARD_UTILS) += snd-soc-simple-card-utils.o
obj-$(CONFIG_SND_SIMPLE_CARD) += snd-soc-simple-card.o
obj-$(CONFIG_SND_SIMPLE_SCU_CARD) += snd-soc-simple-scu-card.o
+obj-$(CONFIG_SND_SIMPLE_GRAPH_CARD) += snd-soc-simple-graph-card.o
diff --git a/sound/soc/generic/simple-graph-card.c b/sound/soc/generic/simple-graph-card.c
new file mode 100644
index 0000000..a98b13f
--- /dev/null
+++ b/sound/soc/generic/simple-graph-card.c
@@ -0,0 +1,462 @@
+/*
+ * ASoC simple graph sound card support
+ *
+ * Copyright (C) 2016 Renesas Solutions Corp.
+ * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
+ *
+ * based on ${LINUX}/sound/soc/generic/simple-card.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/platform_device.h>
+#include <linux/string.h>
+#include <sound/jack.h>
+#include <sound/simple_card_utils.h>
+
+struct asoc_simple_jack {
+ struct snd_soc_jack jack;
+ struct snd_soc_jack_pin pin;
+ struct snd_soc_jack_gpio gpio;
+};
+
+struct simple_card_data {
+ struct snd_soc_card snd_card;
+ struct simple_dai_props {
+ struct asoc_simple_dai cpu_dai;
+ struct asoc_simple_dai codec_dai;
+ unsigned int mclk_fs;
+ } *dai_props;
+ struct asoc_simple_jack hp_jack;
+ struct asoc_simple_jack mic_jack;
+ struct snd_soc_dai_link *dai_link;
+ unsigned int mclk_fs;
+};
+
+#define simple_priv_to_dev(priv) ((priv)->snd_card.dev)
+#define simple_priv_to_link(priv, i) ((priv)->snd_card.dai_link + (i))
+#define simple_priv_to_props(priv, i) ((priv)->dai_props + (i))
+
+#define PREFIX "simple-audio-card,"
+
+#define asoc_simple_card_init_hp(card, node, sjack, prefix) \
+ asoc_simple_card_init_jack(card, node, sjack, 1, prefix)
+#define asoc_simple_card_init_mic(card, node, sjack, prefix) \
+ asoc_simple_card_init_jack(card, node, sjack, 0, prefix)
+static int asoc_simple_card_init_jack(struct snd_soc_card *card,
+ struct device_node *node,
+ struct asoc_simple_jack *sjack,
+ int is_hp, char *prefix)
+{
+ enum of_gpio_flags flags;
+ char prop[128];
+ char *pin_name;
+ char *gpio_name;
+ int mask;
+ int det;
+
+ sjack->gpio.gpio = -ENOENT;
+
+ if (is_hp) {
+ snprintf(prop, sizeof(prop), "%shp-det-gpio", prefix);
+ pin_name = "Headphones";
+ gpio_name = "Headphone detection";
+ mask = SND_JACK_HEADPHONE;
+ } else {
+ snprintf(prop, sizeof(prop), "%smic-det-gpio", prefix);
+ pin_name = "Mic Jack";
+ gpio_name = "Mic detection";
+ mask = SND_JACK_MICROPHONE;
+ }
+
+ det = of_get_named_gpio_flags(node, prop, 0, &flags);
+ if (det == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ if (gpio_is_valid(det)) {
+ sjack->pin.pin = pin_name;
+ sjack->pin.mask = mask;
+
+ sjack->gpio.name = gpio_name;
+ sjack->gpio.report = mask;
+ sjack->gpio.gpio = det;
+ sjack->gpio.invert = !!(flags & OF_GPIO_ACTIVE_LOW);
+ sjack->gpio.debounce_time = 150;
+
+ snd_soc_card_jack_new(card, pin_name, mask,
+ &sjack->jack,
+ &sjack->pin, 1);
+
+ snd_soc_jack_add_gpios(&sjack->jack, 1,
+ &sjack->gpio);
+ }
+
+ return 0;
+}
+
+static void asoc_simple_card_remove_jack(struct asoc_simple_jack *sjack)
+{
+ if (gpio_is_valid(sjack->gpio.gpio))
+ snd_soc_jack_free_gpios(&sjack->jack, 1, &sjack->gpio);
+}
+
+static int asoc_simple_card_startup(struct snd_pcm_substream *substream)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct simple_dai_props *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+ int ret;
+
+ ret = clk_prepare_enable(dai_props->cpu_dai.clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(dai_props->codec_dai.clk);
+ if (ret)
+ clk_disable_unprepare(dai_props->cpu_dai.clk);
+
+ return ret;
+}
+
+static void asoc_simple_card_shutdown(struct snd_pcm_substream *substream)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct simple_dai_props *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+
+ clk_disable_unprepare(dai_props->cpu_dai.clk);
+
+ clk_disable_unprepare(dai_props->codec_dai.clk);
+}
+
+static int asoc_simple_card_hw_params(struct snd_pcm_substream *substream,
+ struct snd_pcm_hw_params *params)
+{
+ struct snd_soc_pcm_runtime *rtd = substream->private_data;
+ struct snd_soc_dai *codec_dai = rtd->codec_dai;
+ struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct simple_dai_props *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+ unsigned int mclk, mclk_fs = 0;
+ int ret = 0;
+
+ if (priv->mclk_fs)
+ mclk_fs = priv->mclk_fs;
+ else if (dai_props->mclk_fs)
+ mclk_fs = dai_props->mclk_fs;
+
+ if (mclk_fs) {
+ mclk = params_rate(params) * mclk_fs;
+ ret = snd_soc_dai_set_sysclk(codec_dai, 0, mclk,
+ SND_SOC_CLOCK_IN);
+ if (ret && ret != -ENOTSUPP)
+ goto err;
+
+ ret = snd_soc_dai_set_sysclk(cpu_dai, 0, mclk,
+ SND_SOC_CLOCK_OUT);
+ if (ret && ret != -ENOTSUPP)
+ goto err;
+ }
+ return 0;
+err:
+ return ret;
+}
+
+static struct snd_soc_ops asoc_simple_card_ops = {
+ .startup = asoc_simple_card_startup,
+ .shutdown = asoc_simple_card_shutdown,
+ .hw_params = asoc_simple_card_hw_params,
+};
+
+static int asoc_simple_card_dai_init(struct snd_soc_pcm_runtime *rtd)
+{
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(rtd->card);
+ struct device *dev = simple_priv_to_dev(priv);
+ struct device *cpu_dev = dev->parent;
+ struct snd_soc_dai *codec = rtd->codec_dai;
+ struct snd_soc_dai *cpu = rtd->cpu_dai;
+ struct snd_soc_card *card = rtd->card;
+ struct simple_dai_props *dai_props =
+ simple_priv_to_props(priv, rtd->num);
+ struct device_node *cpu_port = of_graph_get_top_port(cpu_dev);
+ int ret;
+
+ ret = asoc_simple_card_init_dai(codec, &dai_props->codec_dai);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_init_dai(cpu, &dai_props->cpu_dai);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_init_hp(card, cpu_port, &priv->hp_jack, PREFIX);
+ if (ret < 0)
+ return ret;
+
+ ret = asoc_simple_card_init_mic(card, cpu_port, &priv->hp_jack, PREFIX);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+static int asoc_simple_card_dai_link_of(struct device_node *cpu_ep,
+ struct simple_card_data *priv,
+ int idx)
+{
+ struct device *dev = simple_priv_to_dev(priv);
+ struct snd_soc_dai_link *dai_link = simple_priv_to_link(priv, idx);
+ struct simple_dai_props *dai_props = simple_priv_to_props(priv, idx);
+ struct asoc_simple_dai *cpu_dai = &dai_props->cpu_dai;
+ struct asoc_simple_dai *codec_dai = &dai_props->codec_dai;
+ struct device_node *cpu_port;
+ struct device_node *cpu_remote_ep;
+ struct device_node *codec_ep;
+ int ret;
+
+ codec_ep = of_graph_get_remote_endpoint(cpu_ep);
+ cpu_remote_ep = of_graph_get_remote_endpoint(codec_ep);
+
+ if (cpu_ep != cpu_remote_ep) {
+ dev_err(dev, "endpoint parse error\n");
+ ret = -EINVAL;
+ goto dai_link_of_err;
+ }
+
+ cpu_port = cpu_ep->parent;
+
+ ret = asoc_simple_card_parse_daifmt(dev, cpu_port, codec_ep,
+ PREFIX, &dai_link->dai_fmt);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ of_property_read_u32(cpu_port, "mclk-fs", &dai_props->mclk_fs);
+
+ ret = asoc_simple_card_parse_graph_cpu(cpu_ep, dai_link);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = asoc_simple_card_parse_graph_codec(codec_ep, dai_link);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = snd_soc_of_parse_tdm_slot(cpu_ep,
+ &cpu_dai->tx_slot_mask,
+ &cpu_dai->rx_slot_mask,
+ &cpu_dai->slots,
+ &cpu_dai->slot_width);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = snd_soc_of_parse_tdm_slot(codec_ep,
+ &codec_dai->tx_slot_mask,
+ &codec_dai->rx_slot_mask,
+ &codec_dai->slots,
+ &codec_dai->slot_width);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = asoc_simple_card_parse_clk_cpu(cpu_ep, dai_link, cpu_dai);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = asoc_simple_card_parse_clk_codec(codec_ep, dai_link, codec_dai);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = asoc_simple_card_canonicalize_dailink(dai_link);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ ret = asoc_simple_card_set_dailink_name(dev, dai_link,
+ "%s-%s",
+ dai_link->cpu_dai_name,
+ dai_link->codec_dai_name);
+ if (ret < 0)
+ goto dai_link_of_err;
+
+ dai_link->ops = &asoc_simple_card_ops;
+ dai_link->init = asoc_simple_card_dai_init;
+
+ dev_dbg(dev, "\tname : %s\n", dai_link->stream_name);
+ dev_dbg(dev, "\tformat : %04x\n", dai_link->dai_fmt);
+ dev_dbg(dev, "\tcpu : %s / %d\n",
+ dai_link->cpu_dai_name,
+ dai_props->cpu_dai.sysclk);
+ dev_dbg(dev, "\tcodec : %s / %d\n",
+ dai_link->codec_dai_name,
+ dai_props->codec_dai.sysclk);
+
+ asoc_simple_card_canonicalize_cpu(dai_link,
+ priv->snd_card.num_links == 1);
+
+dai_link_of_err:
+ of_node_put(codec_ep);
+ of_node_put(cpu_remote_ep);
+
+ return ret;
+}
+
+static int asoc_simple_card_parse_of(struct device_node *node,
+ struct simple_card_data *priv)
+{
+ struct device *dev = simple_priv_to_dev(priv);
+ struct device *cpu_dev = dev->parent;
+ struct device_node *top_port = of_graph_get_top_port(cpu_dev);
+ struct snd_soc_card *card = &priv->snd_card;
+ struct device_node *port, *ep;
+ int i = 0, ret;
+
+ if (!node)
+ return -EINVAL;
+
+ for_each_of_port(node, port) {
+ /* The off-codec widgets */
+ if (of_property_read_bool(port, PREFIX "widgets")) {
+ ret = snd_soc_of_parse_audio_simple_widgets_from_node(
+ &priv->snd_card,
+ port, PREFIX "widgets");
+ if (ret)
+ return ret;
+ }
+
+ /* DAPM routes */
+ if (of_property_read_bool(port, PREFIX "routing")) {
+ ret = snd_soc_of_parse_audio_routing_from_node(
+ &priv->snd_card,
+ port, PREFIX "routing");
+ if (ret)
+ return ret;
+ }
+
+ /* Factor to mclk, used in hw_params() */
+ of_property_read_u32(port, PREFIX "mclk-fs", &priv->mclk_fs);
+
+ for_each_of_endpoint_in_port(port, ep) {
+ ret = asoc_simple_card_dai_link_of(ep, priv, i);
+ if (ret < 0) {
+ of_node_put(ep);
+ return ret;
+ }
+ i++;
+ }
+ }
+
+ ret = asoc_simple_card_parse_card_name(card, top_port, PREFIX);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int asoc_simple_card_probe(struct platform_device *pdev)
+{
+ struct simple_card_data *priv;
+ struct snd_soc_dai_link *dai_link;
+ struct simple_dai_props *dai_props;
+ struct device *dev = &pdev->dev;
+ struct device *cpu_dev = pdev->dev.parent;
+ struct device_node *cpu_node = cpu_dev->of_node;
+ struct asoc_simple_graph_card_info *info = pdev->dev.platform_data;
+ int num, ret;
+
+ if (!info)
+ return -EINVAL;
+
+ /* Allocate the private data and the DAI link array */
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ num = info->endpoint_num;
+
+ dai_props = devm_kzalloc(dev, sizeof(*dai_props) * num, GFP_KERNEL);
+ dai_link = devm_kzalloc(dev, sizeof(*dai_link) * num, GFP_KERNEL);
+ if (!dai_props || !dai_link)
+ return -ENOMEM;
+
+ priv->dai_props = dai_props;
+ priv->dai_link = dai_link;
+
+ /* Init snd_soc_card */
+ priv->snd_card.owner = THIS_MODULE;
+ priv->snd_card.dev = dev;
+ priv->snd_card.dai_link = priv->dai_link;
+ priv->snd_card.num_links = num;
+
+ ret = asoc_simple_card_parse_of(cpu_node, priv);
+ if (ret < 0) {
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "parse error %d\n", ret);
+ goto err;
+ }
+
+ /*
+ * FIXME
+ *
+ * This driver is assuming that it will be called from
+ * asoc_simple_card_try_to_probe_graph_card() which
+ * is using platform_device_register_full().
+ * This means it is not came from DT. But this driver itself
+ * will be used as part of ALSA SoC (= sound card).
+ * Because of these background, it might fail in
+ * snd_pcm_lib_malloc_pages() on .hw_params.
+ * Because, noone cares its dma_ops, and result of get_dma_ops()
+ * is based on its architecture.
+ * So, it should call arch_setup_dma_ops() from somewhere,
+ * otherwise, for example, ARM is no problem, but ARM64 will be fail.
+ * But, of_platform_device_xxx() are not good solution today.
+ * This driver calls it by itself here. Please fixme
+ * see also
+ * linux/sound/soc/generic/simple-card-utils.c ::
+ * asoc_simple_card_try_to_probe_graph_card()
+ */
+ of_dma_configure(dev, dev->of_node);
+
+ snd_soc_card_set_drvdata(&priv->snd_card, priv);
+
+ ret = devm_snd_soc_register_card(dev, &priv->snd_card);
+ if (ret >= 0)
+ return ret;
+err:
+ asoc_simple_card_clean_reference(&priv->snd_card);
+
+ return ret;
+}
+
+static int asoc_simple_card_remove(struct platform_device *pdev)
+{
+ struct snd_soc_card *card = platform_get_drvdata(pdev);
+ struct simple_card_data *priv = snd_soc_card_get_drvdata(card);
+
+ asoc_simple_card_remove_jack(&priv->hp_jack);
+ asoc_simple_card_remove_jack(&priv->mic_jack);
+
+ return asoc_simple_card_clean_reference(&priv->snd_card);
+}
+
+static struct platform_driver asoc_simple_card = {
+ .driver = {
+ .name = "asoc-simple-graph-card",
+ },
+ .probe = asoc_simple_card_probe,
+ .remove = asoc_simple_card_remove,
+};
+module_platform_driver(asoc_simple_card);
+
+MODULE_ALIAS("platform:asoc-simple-graph-card");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("ASoC Simple Graph Sound Card");
+MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>");
--
1.9.1
^ permalink raw reply related
* [PATCH v3 14/17] ASoC: add simple-graph-card document
From: Kuninori Morimoto @ 2016-11-11 1:23 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- Added how to use Simple-Graph-Card, and cleanup
.../bindings/sound/simple-graph-card.txt | 65 ++++++++++++++++++++++
1 file changed, 65 insertions(+)
create mode 100644 Documentation/devicetree/bindings/sound/simple-graph-card.txt
diff --git a/Documentation/devicetree/bindings/sound/simple-graph-card.txt b/Documentation/devicetree/bindings/sound/simple-graph-card.txt
new file mode 100644
index 0000000..11823b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/simple-graph-card.txt
@@ -0,0 +1,65 @@
+Simple-Graph-Card:
+
+Simple-Graph-Card specifies audio DAI connections of SoC <-> codec.
+It is based on common bindings for device graphs.
+see ${LINUX}/Documentation/devicetree/bindings/graph.txt
+
+Basically, Simple-Graph-Card property is same as Simple-Card.
+see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt
+
+Below are same as Simple-Card.
+
+- simple-audio-card,name
+- simple-audio-card,widgets
+- simple-audio-card,routing
+- simple-audio-card,mclk-fs
+- simple-audio-card,hp-det-gpio
+- simple-audio-card,mic-det-gpio
+- simple-audio-card,format
+- simple-audio-card,frame-master
+- simple-audio-card,bitclock-master
+- simple-audio-card,bitclock-inversion
+- simple-audio-card,frame-inversion
+- simple-audio-card,mclk-fs
+- simple-audio-card,dai-tdm-slot-num
+- simple-audio-card,dai-tdm-slot-width
+- clocks / system-clock-frequency
+
+In Simple-Graph-Card, above properties need in CPU side port on DT.
+And it needs to have "compatible" property too.
+In addition, CPU side driver needs to call asoc_simple_card_try_to_probe_graph_card().
+It will probe specified Card driver if it could find "compatible" property on port.
+Otherwise, it will do nothing.
+
+Required properties:
+
+- compatible : "asoc-simple-graph-card";
+
+Example
+
+ak4643: codec@12 {
+ compatible = "asahi-kasei,ak4643";
+ ...
+ port {
+ ak4643_port: endpoint {
+ remote-endpoint = <&rcar_ak4643_port>;
+ clocks = <&audio_clock>;
+ };
+ };
+};
+
+rcar_sound {
+ ...
+ port {
+ compatible = "asoc-simple-graph-card";
+
+ simple-audio-card,format = "left_j";
+ simple-audio-card,bitclock-master = <&ak4643_port>;
+ simple-audio-card,frame-master = <&ak4643_port>;
+
+ rcar_ak4643_port: endpoint {
+ remote-endpoint = <&ak4643_port>;
+ ...
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related
* [PATCH v3 13/17] ASoC: simple-card-utils: adjust for graph on asoc_simple_card_parse_card_name
From: Kuninori Morimoto @ 2016-11-11 1:22 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
include/sound/simple_card_utils.h | 1 +
sound/soc/generic/simple-card-utils.c | 3 ++-
sound/soc/generic/simple-card.c | 2 +-
sound/soc/generic/simple-scu-card.c | 2 +-
4 files changed, 5 insertions(+), 3 deletions(-)
diff --git a/include/sound/simple_card_utils.h b/include/sound/simple_card_utils.h
index 7006150..afca6bd 100644
--- a/include/sound/simple_card_utils.h
+++ b/include/sound/simple_card_utils.h
@@ -36,6 +36,7 @@ int asoc_simple_card_set_dailink_name(struct device *dev,
struct snd_soc_dai_link *dai_link,
const char *fmt, ...);
int asoc_simple_card_parse_card_name(struct snd_soc_card *card,
+ struct device_node *node,
char *prefix);
#define asoc_simple_card_parse_clk_cpu(node, dai_link, simple_dai) \
diff --git a/sound/soc/generic/simple-card-utils.c b/sound/soc/generic/simple-card-utils.c
index 85120f5..604f1f9 100644
--- a/sound/soc/generic/simple-card-utils.c
+++ b/sound/soc/generic/simple-card-utils.c
@@ -81,6 +81,7 @@ int asoc_simple_card_set_dailink_name(struct device *dev,
EXPORT_SYMBOL_GPL(asoc_simple_card_set_dailink_name);
int asoc_simple_card_parse_card_name(struct snd_soc_card *card,
+ struct device_node *node,
char *prefix)
{
char prop[128];
@@ -89,7 +90,7 @@ int asoc_simple_card_parse_card_name(struct snd_soc_card *card,
snprintf(prop, sizeof(prop), "%sname", prefix);
/* Parse the card name from DT */
- ret = snd_soc_of_parse_card_name(card, prop);
+ ret = snd_soc_of_parse_card_name_from_node(card, node, prop);
if (ret < 0)
return ret;
diff --git a/sound/soc/generic/simple-card.c b/sound/soc/generic/simple-card.c
index f608f8d2..342ff53 100644
--- a/sound/soc/generic/simple-card.c
+++ b/sound/soc/generic/simple-card.c
@@ -401,7 +401,7 @@ static int asoc_simple_card_parse_of(struct device_node *node,
goto card_parse_end;
}
- ret = asoc_simple_card_parse_card_name(&priv->snd_card, PREFIX);
+ ret = asoc_simple_card_parse_card_name(&priv->snd_card, NULL, PREFIX);
if (ret < 0)
goto card_parse_end;
diff --git a/sound/soc/generic/simple-scu-card.c b/sound/soc/generic/simple-scu-card.c
index 348e9a7..a8164a2 100644
--- a/sound/soc/generic/simple-scu-card.c
+++ b/sound/soc/generic/simple-scu-card.c
@@ -239,7 +239,7 @@ static int asoc_simple_card_parse_of(struct device_node *node,
i++;
}
- ret = asoc_simple_card_parse_card_name(&priv->snd_card, PREFIX);
+ ret = asoc_simple_card_parse_card_name(&priv->snd_card, NULL, PREFIX);
if (ret < 0)
return ret;
--
1.9.1
^ permalink raw reply related
* [PATCH v3 12/17] ASoC: simple-card-utils: add asoc_simple_card_try_to_probe_graph_card()
From: Kuninori Morimoto @ 2016-11-11 1:22 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
From: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
If CPU/Platform side driver probes successfully, and if it is supporting
both previous normal sound card style and graph style DT, it can call
asoc_simple_card_try_to_probe_graph_card().
It checks graph style DT, and do nothing if it was non graph style DT,
or register new simple-graph-card driver if graph style DT.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
---
v2 -> v3
- no change
include/sound/simple_card_utils.h | 8 +++++++
sound/soc/generic/simple-card-utils.c | 45 +++++++++++++++++++++++++++++++++++
2 files changed, 53 insertions(+)
diff --git a/include/sound/simple_card_utils.h b/include/sound/simple_card_utils.h
index 4b58954..7006150 100644
--- a/include/sound/simple_card_utils.h
+++ b/include/sound/simple_card_utils.h
@@ -22,6 +22,10 @@ struct asoc_simple_dai {
struct clk *clk;
};
+struct asoc_simple_graph_card_info {
+ int endpoint_num; /* sound endpoint number */
+};
+
int asoc_simple_card_parse_daifmt(struct device *dev,
struct device_node *node,
struct device_node *codec,
@@ -78,4 +82,8 @@ void asoc_simple_card_canonicalize_cpu(struct snd_soc_dai_link *dai_link,
int asoc_simple_card_clean_reference(struct snd_soc_card *card);
+void asoc_simple_card_try_to_probe_graph_card(struct device *dev,
+ struct asoc_simple_graph_card_info *info);
+
+
#endif /* __SIMPLE_CARD_CORE_H */
diff --git a/sound/soc/generic/simple-card-utils.c b/sound/soc/generic/simple-card-utils.c
index 373ada3..85120f5 100644
--- a/sound/soc/generic/simple-card-utils.c
+++ b/sound/soc/generic/simple-card-utils.c
@@ -8,6 +8,7 @@
* published by the Free Software Foundation.
*/
#include <linux/clk.h>
+#include <linux/dma-mapping.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_graph.h>
@@ -285,6 +286,50 @@ int asoc_simple_card_clean_reference(struct snd_soc_card *card)
}
EXPORT_SYMBOL_GPL(asoc_simple_card_clean_reference);
+void asoc_simple_card_try_to_probe_graph_card(struct device *dev,
+ struct asoc_simple_graph_card_info *info)
+{
+ struct platform_device_info pdevinfo;
+ struct device_node *node;
+ const char *compatible;
+ int ret;
+
+ node = of_graph_get_top_port(dev);
+ if (!node || !info)
+ /*
+ * It doesn't have graph base sound DT, or its infomation.
+ * Do nothing here, It assumes that system has
+ * normal sound card.
+ */
+ return;
+
+ ret = of_property_read_string(node, "compatible", &compatible);
+ if (ret < 0)
+ goto probe_err;
+
+ /*
+ * FIXME
+ *
+ * It should use of_platform_xxx() instead of
+ * platform_device_register_full() ? but there is no solution.
+ * see also
+ * linux/sound/soc/generic/simple-graph-card.c :: asoc_simple_card_probe
+ */
+
+ memset(&pdevinfo, 0, sizeof(pdevinfo));
+ pdevinfo.parent = dev;
+ pdevinfo.id = PLATFORM_DEVID_AUTO;
+ pdevinfo.name = compatible;
+ pdevinfo.dma_mask = DMA_BIT_MASK(32);
+ pdevinfo.data = info;
+ pdevinfo.size_data = sizeof(*info);
+ platform_device_register_full(&pdevinfo);
+
+probe_err:
+ of_node_put(node);
+}
+EXPORT_SYMBOL_GPL(asoc_simple_card_try_to_probe_graph_card);
+
/* Module information */
MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>");
MODULE_DESCRIPTION("ALSA SoC Simple Card Utils");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 11/17] ASoC: simple-card-utils: add asoc_simple_card_parse_graph_dai()
From: Kuninori Morimoto @ 2016-11-11 1:21 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
From: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
simple-card already has asoc_simple_card_parse_dai(),
but graph base parsing needs graph specific version of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
---
v2 -> v3
- no change
include/sound/simple_card_utils.h | 10 +++++++
sound/soc/generic/simple-card-utils.c | 50 +++++++++++++++++++++++++++++++++++
2 files changed, 60 insertions(+)
diff --git a/include/sound/simple_card_utils.h b/include/sound/simple_card_utils.h
index fd641255..4b58954 100644
--- a/include/sound/simple_card_utils.h
+++ b/include/sound/simple_card_utils.h
@@ -59,6 +59,16 @@ int asoc_simple_card_parse_dai(struct device_node *node,
const char *cells_name,
int *is_single_links);
+#define asoc_simple_card_parse_graph_cpu(ep, dai_link) \
+ asoc_simple_card_parse_graph_dai(ep, &dai_link->cpu_of_node, \
+ &dai_link->cpu_dai_name)
+#define asoc_simple_card_parse_graph_codec(ep, dai_link) \
+ asoc_simple_card_parse_graph_dai(ep, &dai_link->codec_of_node, \
+ &dai_link->codec_dai_name)
+int asoc_simple_card_parse_graph_dai(struct device_node *ep,
+ struct device_node **endpoint_np,
+ const char **dai_name);
+
int asoc_simple_card_init_dai(struct snd_soc_dai *dai,
struct asoc_simple_dai *simple_dai);
diff --git a/sound/soc/generic/simple-card-utils.c b/sound/soc/generic/simple-card-utils.c
index e5b80f5..373ada3 100644
--- a/sound/soc/generic/simple-card-utils.c
+++ b/sound/soc/generic/simple-card-utils.c
@@ -10,6 +10,7 @@
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_graph.h>
#include <sound/simple_card_utils.h>
int asoc_simple_card_parse_daifmt(struct device *dev,
@@ -164,6 +165,55 @@ int asoc_simple_card_parse_dai(struct device_node *node,
}
EXPORT_SYMBOL_GPL(asoc_simple_card_parse_dai);
+int asoc_simple_card_parse_graph_dai(struct device_node *ep,
+ struct device_node **dai_of_node,
+ const char **dai_name)
+{
+ struct device_node *node, *port, *endpoint;
+ int i, id;
+
+ if (!ep)
+ return 0;
+
+ /*
+ * of_graph_get_port_parent() will call
+ * of_node_put(). So, call of_node_get() here
+ */
+ of_node_get(ep);
+ node = of_graph_get_port_parent(ep);
+
+ i = 0;
+ id = -1;
+ for_each_of_port(node, port) {
+ for_each_of_endpoint_in_port(port, endpoint) {
+ if (endpoint == ep)
+ id = i;
+ i++;
+ }
+ }
+ if (id < 0)
+ return -ENODEV;
+
+ /* Get dai->name */
+ if (dai_name) {
+ struct of_phandle_args args;
+ int ret;
+
+ args.np = node;
+ args.args[0] = id;
+ args.args_count = (i > 1);
+
+ ret = snd_soc_get_dai_name(&args, dai_name);
+ if (ret < 0)
+ return ret;
+ }
+
+ *dai_of_node = node;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(asoc_simple_card_parse_graph_dai);
+
int asoc_simple_card_init_dai(struct snd_soc_dai *dai,
struct asoc_simple_dai *simple_dai)
{
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 10/17] of_graph: add of_graph_get_port/endpoint_count()
From: Kuninori Morimoto @ 2016-11-11 1:21 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
OF graph want to count its port/endpoint number, same as
of_get_child_count(). This patch adds these functions.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
drivers/of/base.c | 24 ++++++++++++++++++++++++
include/linux/of_graph.h | 8 ++++++++
2 files changed, 32 insertions(+)
diff --git a/drivers/of/base.c b/drivers/of/base.c
index b11f533..e795d0f 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -2584,3 +2584,27 @@ struct device_node *of_graph_get_remote_port(const struct device_node *node)
return of_get_next_parent(np);
}
EXPORT_SYMBOL(of_graph_get_remote_port);
+
+int of_graph_get_port_count(const struct device_node *np)
+{
+ struct device_node *port;
+ int num = 0;
+
+ for_each_of_port(np, port)
+ num++;
+
+ return num;
+}
+EXPORT_SYMBOL(of_graph_get_port_count);
+
+int of_graph_get_endpoint_count(const struct device_node *np)
+{
+ struct device_node *port, *endpoint;
+ int num = 0;
+
+ for_each_of_endpoint(np, port, endpoint)
+ num++;
+
+ return num;
+}
+EXPORT_SYMBOL(of_graph_get_endpoint_count);
diff --git a/include/linux/of_graph.h b/include/linux/of_graph.h
index 3de036f..c060a7c 100644
--- a/include/linux/of_graph.h
+++ b/include/linux/of_graph.h
@@ -54,6 +54,8 @@ struct of_endpoint {
#ifdef CONFIG_OF
int of_graph_parse_endpoint(const struct device_node *node,
struct of_endpoint *endpoint);
+int of_graph_get_port_count(const struct device_node *np);
+int of_graph_get_endpoint_count(const struct device_node *np);
struct device_node *of_graph_get_port_by_id(struct device_node *node, u32 id);
struct device_node *of_graph_get_top_port(struct device *dev);
struct device_node *of_graph_get_next_port(const struct device_node *parent,
@@ -79,6 +81,12 @@ static inline int of_graph_parse_endpoint(const struct device_node *node,
return -ENOSYS;
}
+static inline int of_graph_get_endpoint_count(const struct device_node *np,
+ char *type)
+{
+ return 0;
+}
+
static inline struct device_node *of_graph_get_port_by_id(
struct device_node *node, u32 id)
{
--
1.9.1
^ permalink raw reply related
* [PATCH v3 09/17] of_graph: add for_each_of_port() / for_each_of_endpoint_in_port()
From: Kuninori Morimoto @ 2016-11-11 1:21 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
OF graph is used mainly from V4L2, but ALSA needs to use it. It already
has for_each_endpoint_of_node() which is for-loop for each endpoint.
But, ALSA needs for-loop for each port[s], and for-loop for each
endpoint of inside port[s]. This patch adds for_each_of_port()
and for_each_of_endpoint_in_port() for this purpose.
And it also adds for_each_of_endpoint() which is similar to
for_each_endpoint_of_node(). The difference is it can catch port
handle during for-loop.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
drivers/of/base.c | 64 ++++++++++++++++++++++++++++++++++++++++++++++++
include/linux/of_graph.h | 29 ++++++++++++++++++++++
2 files changed, 93 insertions(+)
diff --git a/drivers/of/base.c b/drivers/of/base.c
index e49eb28..b11f533 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -2354,6 +2354,70 @@ struct device_node *of_graph_get_top_port(struct device *dev)
EXPORT_SYMBOL(of_graph_get_top_port);
/**
+ * of_graph_get_next_port() - get next port node
+ * @parent: pointer to the parent device node
+ * @prev: previous endpoint node, or NULL to get first
+ *
+ * Return: An 'endpoint' node pointer with refcount incremented. Refcount
+ * of the passed @prev node is decremented.
+ */
+struct device_node *of_graph_get_next_port(const struct device_node *parent,
+ struct device_node *prev)
+{
+ struct device_node *port;
+ struct device_node *node;
+
+ if (!parent)
+ return NULL;
+
+ node = of_get_child_by_name(parent, "ports");
+ if (node)
+ parent = node;
+
+ /*
+ * Start by locating the port node. If no previous endpoint is specified
+ * search for the first port node, otherwise get the previous endpoint
+ * parent port node.
+ */
+ if (!prev) {
+ port = of_get_child_by_name(parent, "port");
+ if (!port)
+ pr_err("%s(): no port node found in %s\n",
+ __func__, parent->full_name);
+ } else {
+ do {
+ port = of_get_next_child(parent, prev);
+ if (!port)
+ break;
+ } while (of_node_cmp(port->name, "port"));
+ }
+
+ of_node_put(node);
+
+ return port;
+}
+EXPORT_SYMBOL(of_graph_get_next_port);
+
+/**
+ * of_graph_get_next_endpoint_in_port() - get next endpoint node in port
+ * @parent: pointer to the parent device node
+ * @prev: previous endpoint node, or NULL to get first
+ *
+ * Return: An 'endpoint' node pointer with refcount incremented. Refcount
+ * of the passed @prev node is decremented.
+ */
+struct device_node *of_graph_get_next_endpoint_in_port(
+ const struct device_node *port,
+ struct device_node *prev)
+{
+ if (!port)
+ return NULL;
+
+ return of_get_next_child(port, prev);
+}
+EXPORT_SYMBOL(of_graph_get_next_endpoint_in_port);
+
+/**
* of_graph_get_next_endpoint() - get next endpoint node
* @parent: pointer to the parent device node
* @prev: previous endpoint node, or NULL to get first
diff --git a/include/linux/of_graph.h b/include/linux/of_graph.h
index ee823c6..3de036f 100644
--- a/include/linux/of_graph.h
+++ b/include/linux/of_graph.h
@@ -30,6 +30,16 @@ struct of_endpoint {
const struct device_node *local_node;
};
+#define for_each_of_port(parent, port) \
+ for (port = of_graph_get_next_port(parent, NULL); port != NULL; \
+ port = of_graph_get_next_port(parent, port))
+#define for_each_of_endpoint_in_port(port, ep) \
+ for (ep = of_graph_get_next_endpoint_in_port(port, NULL); ep != NULL; \
+ ep = of_graph_get_next_endpoint_in_port(port, ep))
+#define for_each_of_endpoint(parent, port, ep) \
+ for_each_of_port(parent, port) \
+ for_each_of_endpoint_in_port(port, ep)
+
/**
* for_each_endpoint_of_node - iterate over every endpoint in a device node
* @parent: parent device node containing ports and endpoints
@@ -46,6 +56,11 @@ int of_graph_parse_endpoint(const struct device_node *node,
struct of_endpoint *endpoint);
struct device_node *of_graph_get_port_by_id(struct device_node *node, u32 id);
struct device_node *of_graph_get_top_port(struct device *dev);
+struct device_node *of_graph_get_next_port(const struct device_node *parent,
+ struct device_node *prev);
+struct device_node *of_graph_get_next_endpoint_in_port(
+ const struct device_node *port,
+ struct device_node *prev);
struct device_node *of_graph_get_next_endpoint(const struct device_node *parent,
struct device_node *previous);
struct device_node *of_graph_get_endpoint_by_regs(
@@ -70,6 +85,20 @@ static inline struct device_node *of_graph_get_port_by_id(
return NULL;
}
+static inline struct device_node *of_graph_get_next_port(
+ const struct device_node *parent,
+ struct device_node *prev)
+{
+ return NULL;
+}
+
+static inline struct device_node *of_graph_get_next_endpoint_in_port(
+ const struct device_node *port,
+ struct device_node *prev)
+{
+ return NULL;
+}
+
static inline struct device_node *of_graph_get_next_endpoint(
const struct device_node *parent,
struct device_node *previous)
--
1.9.1
^ permalink raw reply related
* [PATCH v3 08/17] of_graph: add of_graph_get_top_port()
From: Kuninori Morimoto @ 2016-11-11 1:20 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
driver want to get top level of port[s] node. This patch adds
of_graph_get_top_port() for this purpose
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
drivers/of/base.c | 24 ++++++++++++++++++++++++
include/linux/of_graph.h | 2 ++
2 files changed, 26 insertions(+)
diff --git a/drivers/of/base.c b/drivers/of/base.c
index fed0b023..e49eb28 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -2330,6 +2330,30 @@ struct device_node *of_graph_get_port_by_id(struct device_node *parent, u32 id)
EXPORT_SYMBOL(of_graph_get_port_by_id);
/**
+ * of_graph_get_top_port() - get the top port node
+ * @dev: pointer to the device
+ *
+ * Return: A 'port' node pointer with refcount incremented. The caller
+ * has to use of_node_put() on it when done.
+ */
+struct device_node *of_graph_get_top_port(struct device *dev)
+{
+ struct device_node *np = dev->of_node;
+ struct device_node *node;
+
+ node = of_get_child_by_name(np, "ports");
+ if (node)
+ return node;
+
+ node = of_get_child_by_name(np, "port");
+ if (node)
+ return node;
+
+ return NULL;
+}
+EXPORT_SYMBOL(of_graph_get_top_port);
+
+/**
* of_graph_get_next_endpoint() - get next endpoint node
* @parent: pointer to the parent device node
* @prev: previous endpoint node, or NULL to get first
diff --git a/include/linux/of_graph.h b/include/linux/of_graph.h
index 80ced0c..ee823c6 100644
--- a/include/linux/of_graph.h
+++ b/include/linux/of_graph.h
@@ -14,6 +14,7 @@
#ifndef __LINUX_OF_GRAPH_H
#define __LINUX_OF_GRAPH_H
+#include <linux/device.h>
#include <linux/types.h>
#include <linux/errno.h>
@@ -44,6 +45,7 @@ struct of_endpoint {
int of_graph_parse_endpoint(const struct device_node *node,
struct of_endpoint *endpoint);
struct device_node *of_graph_get_port_by_id(struct device_node *node, u32 id);
+struct device_node *of_graph_get_top_port(struct device *dev);
struct device_node *of_graph_get_next_endpoint(const struct device_node *parent,
struct device_node *previous);
struct device_node *of_graph_get_endpoint_by_regs(
--
1.9.1
^ permalink raw reply related
* [PATCH v3 07/17] of_graph: add of_graph_get_port_parent()
From: Kuninori Morimoto @ 2016-11-11 1:20 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Linux kernel already has of_graph_get_remote_port_parent(),
but, sometimes we want to get own port parent.
This patch adds of_graph_get_port_parent()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
drivers/of/base.c | 30 ++++++++++++++++++++++--------
include/linux/of_graph.h | 7 +++++++
2 files changed, 29 insertions(+), 8 deletions(-)
diff --git a/drivers/of/base.c b/drivers/of/base.c
index 810acf4..fed0b023 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -2439,6 +2439,27 @@ struct device_node *of_graph_get_remote_endpoint(const struct device_node *node)
EXPORT_SYMBOL(of_graph_get_remote_endpoint);
/**
+ * of_graph_get_port_parent() - get port's parent node
+ * @node: pointer to a local endpoint device_node
+ *
+ * Return: device node associated with endpoint node linked
+ * to @node. Use of_node_put() on it when done.
+ */
+struct device_node *of_graph_get_port_parent(struct device_node *node)
+{
+ unsigned int depth;
+
+ /* Walk 3 levels up only if there is 'ports' node. */
+ for (depth = 3; depth && node; depth--) {
+ node = of_get_next_parent(node);
+ if (depth == 2 && of_node_cmp(node->name, "ports"))
+ break;
+ }
+ return node;
+}
+EXPORT_SYMBOL(of_graph_get_port_parent);
+
+/**
* of_graph_get_remote_port_parent() - get remote port's parent node
* @node: pointer to a local endpoint device_node
*
@@ -2449,18 +2470,11 @@ struct device_node *of_graph_get_remote_port_parent(
const struct device_node *node)
{
struct device_node *np;
- unsigned int depth;
/* Get remote endpoint node. */
np = of_graph_get_remote_endpoint(node);
- /* Walk 3 levels up only if there is 'ports' node. */
- for (depth = 3; depth && np; depth--) {
- np = of_get_next_parent(np);
- if (depth == 2 && of_node_cmp(np->name, "ports"))
- break;
- }
- return np;
+ return of_graph_get_port_parent(np);
}
EXPORT_SYMBOL(of_graph_get_remote_port_parent);
diff --git a/include/linux/of_graph.h b/include/linux/of_graph.h
index d9d6d9c..80ced0c 100644
--- a/include/linux/of_graph.h
+++ b/include/linux/of_graph.h
@@ -50,6 +50,7 @@ struct device_node *of_graph_get_endpoint_by_regs(
const struct device_node *parent, int port_reg, int reg);
struct device_node *of_graph_get_remote_endpoint(
const struct device_node *node);
+struct device_node *of_graph_get_port_parent(struct device_node *node);
struct device_node *of_graph_get_remote_port_parent(
const struct device_node *node);
struct device_node *of_graph_get_remote_port(const struct device_node *node);
@@ -86,6 +87,12 @@ static inline struct device_node *of_graph_get_remote_endpoint(
return NULL;
}
+static inline struct device_node *of_graph_get_port_parent(
+ struct device_node *node)
+{
+ return NULL;
+}
+
static inline struct device_node *of_graph_get_remote_port_parent(
const struct device_node *node)
{
--
1.9.1
^ permalink raw reply related
* [PATCH v3 06/17] of_graph: add of_graph_get_remote_endpoint()
From: Kuninori Morimoto @ 2016-11-11 1:19 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
From: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
It should use same method to get same result.
To getting remote-endpoint node,
let's use of_graph_get_remote_endpoint()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
---
v2 -> v3
- no change
drivers/of/base.c | 18 ++++++++++++++++--
include/linux/of_graph.h | 8 ++++++++
2 files changed, 24 insertions(+), 2 deletions(-)
diff --git a/drivers/of/base.c b/drivers/of/base.c
index d687e6d..810acf4 100644
--- a/drivers/of/base.c
+++ b/drivers/of/base.c
@@ -2425,6 +2425,20 @@ struct device_node *of_graph_get_endpoint_by_regs(
EXPORT_SYMBOL(of_graph_get_endpoint_by_regs);
/**
+ * of_graph_get_remote_endpoint() - get remote endpoint node
+ * @node: pointer to a local endpoint device_node
+ *
+ * Return: Remote endpoint node associated with remote endpoint node linked
+ * to @node. Use of_node_put() on it when done.
+ */
+struct device_node *of_graph_get_remote_endpoint(const struct device_node *node)
+{
+ /* Get remote endpoint node. */
+ return of_parse_phandle(node, "remote-endpoint", 0);
+}
+EXPORT_SYMBOL(of_graph_get_remote_endpoint);
+
+/**
* of_graph_get_remote_port_parent() - get remote port's parent node
* @node: pointer to a local endpoint device_node
*
@@ -2438,7 +2452,7 @@ struct device_node *of_graph_get_remote_port_parent(
unsigned int depth;
/* Get remote endpoint node. */
- np = of_parse_phandle(node, "remote-endpoint", 0);
+ np = of_graph_get_remote_endpoint(node);
/* Walk 3 levels up only if there is 'ports' node. */
for (depth = 3; depth && np; depth--) {
@@ -2462,7 +2476,7 @@ struct device_node *of_graph_get_remote_port(const struct device_node *node)
struct device_node *np;
/* Get remote endpoint node. */
- np = of_parse_phandle(node, "remote-endpoint", 0);
+ np = of_graph_get_remote_endpoint(node);
if (!np)
return NULL;
return of_get_next_parent(np);
diff --git a/include/linux/of_graph.h b/include/linux/of_graph.h
index bb3a5a2..d9d6d9c 100644
--- a/include/linux/of_graph.h
+++ b/include/linux/of_graph.h
@@ -48,6 +48,8 @@ struct device_node *of_graph_get_next_endpoint(const struct device_node *parent,
struct device_node *previous);
struct device_node *of_graph_get_endpoint_by_regs(
const struct device_node *parent, int port_reg, int reg);
+struct device_node *of_graph_get_remote_endpoint(
+ const struct device_node *node);
struct device_node *of_graph_get_remote_port_parent(
const struct device_node *node);
struct device_node *of_graph_get_remote_port(const struct device_node *node);
@@ -78,6 +80,12 @@ static inline struct device_node *of_graph_get_endpoint_by_regs(
return NULL;
}
+static inline struct device_node *of_graph_get_remote_endpoint(
+ const struct device_node *node)
+{
+ return NULL;
+}
+
static inline struct device_node *of_graph_get_remote_port_parent(
const struct device_node *node)
{
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 05/17] ASoC: soc-core: snd_soc_get_dai_name() become non static
From: Kuninori Morimoto @ 2016-11-11 1:19 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
From: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
snd_soc_get_dai_name() is used from snd_soc_of_get_dai_name(),
and it is assuming that DT is using "sound-dai" / "#sound-dai-cells".
But graph base DT is using "remote-endpoint". This patch makes
snd_soc_get_dai_name() non static for graph support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
---
v2 -> v3
- no change
include/sound/soc.h | 2 ++
sound/soc/soc-core.c | 3 ++-
2 files changed, 4 insertions(+), 1 deletion(-)
diff --git a/include/sound/soc.h b/include/sound/soc.h
index 60ac25d..218e3fb 100644
--- a/include/sound/soc.h
+++ b/include/sound/soc.h
@@ -1677,6 +1677,8 @@ unsigned int snd_soc_of_parse_daifmt(struct device_node *np,
const char *prefix,
struct device_node **bitclkmaster,
struct device_node **framemaster);
+int snd_soc_get_dai_name(struct of_phandle_args *args,
+ const char **dai_name);
int snd_soc_of_get_dai_name(struct device_node *of_node,
const char **dai_name);
int snd_soc_of_get_dai_link_codecs(struct device *dev,
diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c
index 8371488..6f911f4 100644
--- a/sound/soc/soc-core.c
+++ b/sound/soc/soc-core.c
@@ -3794,7 +3794,7 @@ unsigned int snd_soc_of_parse_daifmt(struct device_node *np,
}
EXPORT_SYMBOL_GPL(snd_soc_of_parse_daifmt);
-static int snd_soc_get_dai_name(struct of_phandle_args *args,
+int snd_soc_get_dai_name(struct of_phandle_args *args,
const char **dai_name)
{
struct snd_soc_component *pos;
@@ -3846,6 +3846,7 @@ static int snd_soc_get_dai_name(struct of_phandle_args *args,
mutex_unlock(&client_mutex);
return ret;
}
+EXPORT_SYMBOL_GPL(snd_soc_get_dai_name);
int snd_soc_of_get_dai_name(struct device_node *of_node,
const char **dai_name)
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 04/17] ASoC: soc-core: adjust for graph on snd_soc_of_parse_audio_prefix
From: Kuninori Morimoto @ 2016-11-11 1:19 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
include/sound/soc.h | 6 +++++-
sound/soc/soc-core.c | 9 ++++++---
2 files changed, 11 insertions(+), 4 deletions(-)
diff --git a/include/sound/soc.h b/include/sound/soc.h
index f276f69..60ac25d 100644
--- a/include/sound/soc.h
+++ b/include/sound/soc.h
@@ -1658,7 +1658,11 @@ int snd_soc_of_parse_tdm_slot(struct device_node *np,
unsigned int *rx_mask,
unsigned int *slots,
unsigned int *slot_width);
-void snd_soc_of_parse_audio_prefix(struct snd_soc_card *card,
+#define snd_soc_of_parse_audio_prefix(card, codec_conf, of_node, propname) \
+ snd_soc_of_parse_audio_prefix_from_node(card, NULL, codec_conf, \
+ of_node, propname)
+void snd_soc_of_parse_audio_prefix_from_node(struct snd_soc_card *card,
+ struct device_node *np,
struct snd_soc_codec_conf *codec_conf,
struct device_node *of_node,
const char *propname);
diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c
index 79a1045..8371488 100644
--- a/sound/soc/soc-core.c
+++ b/sound/soc/soc-core.c
@@ -3599,15 +3599,18 @@ int snd_soc_of_parse_tdm_slot(struct device_node *np,
}
EXPORT_SYMBOL_GPL(snd_soc_of_parse_tdm_slot);
-void snd_soc_of_parse_audio_prefix(struct snd_soc_card *card,
+void snd_soc_of_parse_audio_prefix_from_node(struct snd_soc_card *card,
+ struct device_node *np,
struct snd_soc_codec_conf *codec_conf,
struct device_node *of_node,
const char *propname)
{
- struct device_node *np = card->dev->of_node;
const char *str;
int ret;
+ if (!np)
+ np = card->dev->of_node;
+
ret = of_property_read_string(np, propname, &str);
if (ret < 0) {
/* no prefix is not error */
@@ -3617,7 +3620,7 @@ void snd_soc_of_parse_audio_prefix(struct snd_soc_card *card,
codec_conf->of_node = of_node;
codec_conf->name_prefix = str;
}
-EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_prefix);
+EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_prefix_from_node);
int snd_soc_of_parse_audio_routing_from_node(struct snd_soc_card *card,
struct device_node *np,
--
1.9.1
^ permalink raw reply related
* [PATCH v3 03/17] ASoC: soc-core: adjust for graph on snd_soc_of_parse_audio_routing
From: Kuninori Morimoto @ 2016-11-11 1:18 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
From: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx-zM6kxYcvzFBBDgjK7y7TUQ@public.gmane.org>
---
v2 -> v3
- no change
include/sound/soc.h | 9 +++++++--
sound/soc/soc-core.c | 9 ++++++---
2 files changed, 13 insertions(+), 5 deletions(-)
diff --git a/include/sound/soc.h b/include/sound/soc.h
index a091c66..f276f69 100644
--- a/include/sound/soc.h
+++ b/include/sound/soc.h
@@ -1662,8 +1662,13 @@ void snd_soc_of_parse_audio_prefix(struct snd_soc_card *card,
struct snd_soc_codec_conf *codec_conf,
struct device_node *of_node,
const char *propname);
-int snd_soc_of_parse_audio_routing(struct snd_soc_card *card,
- const char *propname);
+
+#define snd_soc_of_parse_audio_routing(card, propname) \
+ snd_soc_of_parse_audio_routing_from_node(card, NULL, propname)
+int snd_soc_of_parse_audio_routing_from_node(struct snd_soc_card *card,
+ struct device_node *np,
+ const char *propname);
+
unsigned int snd_soc_of_parse_daifmt(struct device_node *np,
const char *prefix,
struct device_node **bitclkmaster,
diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c
index e56ea42..79a1045 100644
--- a/sound/soc/soc-core.c
+++ b/sound/soc/soc-core.c
@@ -3619,14 +3619,17 @@ void snd_soc_of_parse_audio_prefix(struct snd_soc_card *card,
}
EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_prefix);
-int snd_soc_of_parse_audio_routing(struct snd_soc_card *card,
+int snd_soc_of_parse_audio_routing_from_node(struct snd_soc_card *card,
+ struct device_node *np,
const char *propname)
{
- struct device_node *np = card->dev->of_node;
int num_routes;
struct snd_soc_dapm_route *routes;
int i, ret;
+ if (!np)
+ np = card->dev->of_node;
+
num_routes = of_property_count_strings(np, propname);
if (num_routes < 0 || num_routes & 1) {
dev_err(card->dev,
@@ -3673,7 +3676,7 @@ int snd_soc_of_parse_audio_routing(struct snd_soc_card *card,
return 0;
}
-EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_routing);
+EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_routing_from_node);
unsigned int snd_soc_of_parse_daifmt(struct device_node *np,
const char *prefix,
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 02/17] ASoC: soc-core: adjust for graph on snd_soc_of_parse_audio_simple_widgets
From: Kuninori Morimoto @ 2016-11-11 1:18 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
include/sound/soc.h | 8 ++++++--
sound/soc/soc-core.c | 9 ++++++---
2 files changed, 12 insertions(+), 5 deletions(-)
diff --git a/include/sound/soc.h b/include/sound/soc.h
index 7fff456..a091c66 100644
--- a/include/sound/soc.h
+++ b/include/sound/soc.h
@@ -1647,8 +1647,12 @@ static inline struct snd_soc_platform *snd_soc_kcontrol_platform(
int snd_soc_of_parse_card_name_from_node(struct snd_soc_card *card,
struct device_node *np,
const char *propname);
-int snd_soc_of_parse_audio_simple_widgets(struct snd_soc_card *card,
- const char *propname);
+#define snd_soc_of_parse_audio_simple_widgets(card, propname)\
+ snd_soc_of_parse_audio_simple_widgets_from_node(card, NULL, propname)
+int snd_soc_of_parse_audio_simple_widgets_from_node(struct snd_soc_card *card,
+ struct device_node *np,
+ const char *propname);
+
int snd_soc_of_parse_tdm_slot(struct device_node *np,
unsigned int *tx_mask,
unsigned int *rx_mask,
diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c
index 088a158..e56ea42 100644
--- a/sound/soc/soc-core.c
+++ b/sound/soc/soc-core.c
@@ -3462,14 +3462,17 @@ int snd_soc_of_parse_card_name_from_node(struct snd_soc_card *card,
SND_SOC_DAPM_SPK("Speaker", NULL),
};
-int snd_soc_of_parse_audio_simple_widgets(struct snd_soc_card *card,
+int snd_soc_of_parse_audio_simple_widgets_from_node(struct snd_soc_card *card,
+ struct device_node *np,
const char *propname)
{
- struct device_node *np = card->dev->of_node;
struct snd_soc_dapm_widget *widgets;
const char *template, *wname;
int i, j, num_widgets, ret;
+ if (!np)
+ np = card->dev->of_node;
+
num_widgets = of_property_count_strings(np, propname);
if (num_widgets < 0) {
dev_err(card->dev,
@@ -3540,7 +3543,7 @@ int snd_soc_of_parse_audio_simple_widgets(struct snd_soc_card *card,
return 0;
}
-EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_simple_widgets);
+EXPORT_SYMBOL_GPL(snd_soc_of_parse_audio_simple_widgets_from_node);
static int snd_soc_of_get_slot_mask(struct device_node *np,
const char *prop_name,
--
1.9.1
^ permalink raw reply related
* [PATCH v3 01/17] ASoC: soc-core: adjust for graph on snd_soc_of_parse_card_name
From: Kuninori Morimoto @ 2016-11-11 1:17 UTC (permalink / raw)
To: Rob Herring, Mark Brown
Cc: Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi, Grant Likely,
Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <87vavurf4y.wl%kuninori.morimoto.gx@renesas.com>
From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
---
v2 -> v3
- no change
include/sound/soc.h | 7 +++++--
sound/soc/soc-core.c | 11 ++++++-----
2 files changed, 11 insertions(+), 7 deletions(-)
diff --git a/include/sound/soc.h b/include/sound/soc.h
index 91a8a03..7fff456 100644
--- a/include/sound/soc.h
+++ b/include/sound/soc.h
@@ -1642,8 +1642,11 @@ static inline struct snd_soc_platform *snd_soc_kcontrol_platform(
int snd_soc_util_init(void);
void snd_soc_util_exit(void);
-int snd_soc_of_parse_card_name(struct snd_soc_card *card,
- const char *propname);
+#define snd_soc_of_parse_card_name(card, propname) \
+ snd_soc_of_parse_card_name_from_node(card, NULL, propname)
+int snd_soc_of_parse_card_name_from_node(struct snd_soc_card *card,
+ struct device_node *np,
+ const char *propname);
int snd_soc_of_parse_audio_simple_widgets(struct snd_soc_card *card,
const char *propname);
int snd_soc_of_parse_tdm_slot(struct device_node *np,
diff --git a/sound/soc/soc-core.c b/sound/soc/soc-core.c
index c0bbcd9..088a158 100644
--- a/sound/soc/soc-core.c
+++ b/sound/soc/soc-core.c
@@ -3424,10 +3424,10 @@ void snd_soc_unregister_codec(struct device *dev)
EXPORT_SYMBOL_GPL(snd_soc_unregister_codec);
/* Retrieve a card's name from device tree */
-int snd_soc_of_parse_card_name(struct snd_soc_card *card,
- const char *propname)
+int snd_soc_of_parse_card_name_from_node(struct snd_soc_card *card,
+ struct device_node *np,
+ const char *propname)
{
- struct device_node *np;
int ret;
if (!card->dev) {
@@ -3435,7 +3435,8 @@ int snd_soc_of_parse_card_name(struct snd_soc_card *card,
return -EINVAL;
}
- np = card->dev->of_node;
+ if (!np)
+ np = card->dev->of_node;
ret = of_property_read_string_index(np, propname, 0, &card->name);
/*
@@ -3452,7 +3453,7 @@ int snd_soc_of_parse_card_name(struct snd_soc_card *card,
return 0;
}
-EXPORT_SYMBOL_GPL(snd_soc_of_parse_card_name);
+EXPORT_SYMBOL_GPL(snd_soc_of_parse_card_name_from_node);
static const struct snd_soc_dapm_widget simple_widgets[] = {
SND_SOC_DAPM_MIC("Microphone", NULL),
--
1.9.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox