* [PATCH v8 00/16] mmc: sdhci-msm: Add clk-rates, DDR, HS400 support
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
Hi,
This is v8 version of the patch series which adds support for MSM8996.
Adds HS400 driver support as well.
These are tested on internal msm8996 & db410c HW.
Changes from v7 -> v8 :-
1. Added patch 005 to add dt bindings for xo_clock.
2. Added patch 009 to factor out sdhci_enable_clock as discussed on v7 series.
2.a. Modified patch 010 by making use of sdhci_enable_clock.
2.b. Addressed Stephen's comment on patch 010 to call clk_set_rate unconditionally.
3. Addressed Stephen comments to remove unncessary one line comments, braces and other
minor comments.
4. Added changes from Jeremy in patch 002 for gcc-msm8994 as well for sdcc clk_rcg2_floor_ops.
minor comments.
v7 series was verified on msm8994 target by Jeremy McNicoll.
Older history :-
Below are the changes in v7.
Changes from v6 -> v7 :-
1. Removed patch "clk: Add clk_hw_get_clk() helper API to be used by clk providers"
in v7 as it was not required.
2. Addressed Stephen review comments on -
"clk: qcom: Add rcg ops to return floor value closest to the requested rate"
3. Addressed comments from Stephen to add xo_clock entry in the sdhc clock node.
Using the same xo_clock entry from DT to get the clk_rate of xo_clock used in
sdhci-msm driver. Patch 04 adds this entry into DT.
Patch 05 adds the driver support for xo_clock mentioned above.
Hence there is a minor change in Patch05, which can be reviewed and taken
into the tree.
IMHO, almost all patches are almost done and are ready to be accepted.
Will below process work out?
Patches 001 & 002 :- (clock changes) - Can go via Stephen's Boyd Tree.
Patches 004 & 010 :- (DTS changes) - Can go via Andy Gross.
Patches 003, 005-009 & 011-014 :- (sdhci-msm changes) - Adrian's tree.
Please let me know in case if anything else is required on above.
Changes from v5 -> v6 :-
1. Earlier in v5 series DT node was added to get the clk-rates table
needed for sdhci-msm driver. But this is removed in this(v6) patch series
and instead the clk changes are done in the clk driver as per Rob H comment.
2. Added clk driver changes(patch 1-3) to provide floor rate values of requested
clock for sdhc client.
For following boards- apq8084, msm8996, msm8916, msm8974.
3. Other minor patch comments were addressed.
Changes from v4 -> v5 :-
1. Added HS400 sdhci-msm controller specific changes:- (Patch 10, 11, 12)
2. Addressed comment from Adrian on Patch 07 @[3].
3. Addressed comment from Arnd on Patch 03, to directly add
clk_table into sdhci_msm_host. [4]
4. Addressed comment from Bjorn to not enforce having clk-rates property
in DT for older targets based on discussion at [5]
5. Retained Acks from Adrian on patches (01 & 02 & 06) where there were no
changes made while addressing above comments.
Older history:-
This is v4 version of the patch series.
Patches 01, 02, 05 & 06 were Acked-by Adrian.
Changes from v3 -> v4 :-
1. Addressed comments from Adrian on Patch 03, 07, 08.
2. Addressed comments from Bjorn on Patch 03.
3. Added clk-rate support for sdhc DT nodes to all MSM platforms.
in Pacth 04.
4. Rebased on next branch of Ulf.
Changes from v2 -> v3 :-
1. Addded Patch 01 based on Bjorn comment[2] -
This fixes/unrolls the poor coding style of read/writes of
registers from base sdhci-msm driver.
2. Fixed/unrolled poor style of reads/writes of registers in Patch 02,
based on Bjorn comment[2]. Also changed name of flag from
use_updated_dll_reset -> use_14lpp_dll_reset.
Changes from v1->v2 :-
1. Removed patch 06 & 08 from v1 patch series[1]
(which were introducing unnecessary quirks).
Instead have implemented __sdhci_msm_set_clock version of
sdhci_set_clock in sdhci_msm driver itself in patch 07 of
this patch series.
2. Enabled extra quirk (SDHCI_QUIRK2_PRESET_VALUE_BROKEN) in
patch 05 of this patch series.
Description of patches :-
This patchset adds clk-rates & other required changes to
upstream sdhci-msm driver from codeaurora tree.
It has been tested on a db410c Dragonboard and msm8996 based
platform.
Patch 0001-0003- Adds support in qcom clk driver to return
floor value of requested clock rate instead of ceil rate
for sdhc clients.
Patch 0004- Adds updated dll sequence for newer controllers
which has minor_version >= 0x42. This is required for msm8996.
MSM controller HW recommendation is to use the base MCI clock
and directly control this MCI clock at GCC in order to
change the clk-rate.
Patches 06-08 bring in required change for this to
sdhci-msm.
MSM controller would require 2x clock rate from source
for DDR bus speed modes. Patch 09 adds this support.
Patch 0010- adds DDR support in DT for sdhc1 of msm8916.
Patches 0011-0014- Adds HS400 support to sdhci-msm.
[1]:- http://www.spinics.net/lists/linux-mmc/msg38467.html
[2]:- http://www.spinics.net/lists/linux-mmc/msg38578.html
[3]:- https://patchwork.kernel.org/patch/9289345/
[4]:- https://www.spinics.net/lists/linux-mmc/msg39107.html
[5]:- http://www.spinics.net/lists/linux-mmc/msg38749.html
[6]:- https://patchwork.kernel.org/patch/9297381/
Rajendra Nayak (2):
clk: qcom: Add rcg ops to return floor value closest to the requested
rate
clk: qcom: Move all sdcc rcgs to use clk_rcg2_floor_ops
Ritesh Harjani (12):
mmc: sdhci-msm: Change poor style writel/readl of registers
ARM: dts: Add xo_clock to sdhc nodes on qcom platforms
dt-bindings: sdhci-msm: Add xo_clock property
mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback
mmc: sdhci-msm: Enable few quirks
mmc: sdhci: Factor out sdhci_enable_clock
mmc: sdhci-msm: Implement set_clock callback for sdhci-msm
mmc: sdhci-msm: Add clock changes for DDR mode.
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
mmc: sdhci-msm: Save the calculated tuning phase
mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit
sdhci: sdhci-msm: update dll configuration
Venkat Gopalakrishnan (2):
mmc: sdhci-msm: Update DLL reset sequence
mmc: sdhci-msm: Add HS400 platform support
.../devicetree/bindings/mmc/sdhci-msm.txt | 1 +
arch/arm/boot/dts/qcom-apq8084.dtsi | 16 +-
arch/arm/boot/dts/qcom-msm8974.dtsi | 16 +-
arch/arm64/boot/dts/qcom/msm8916.dtsi | 11 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 9 +-
drivers/clk/qcom/clk-rcg.h | 1 +
drivers/clk/qcom/clk-rcg2.c | 76 ++-
drivers/clk/qcom/common.c | 16 +
drivers/clk/qcom/common.h | 2 +
drivers/clk/qcom/gcc-apq8084.c | 8 +-
drivers/clk/qcom/gcc-msm8916.c | 4 +-
drivers/clk/qcom/gcc-msm8974.c | 8 +-
drivers/clk/qcom/gcc-msm8994.c | 8 +-
drivers/clk/qcom/gcc-msm8996.c | 8 +-
drivers/mmc/host/sdhci-msm.c | 626 +++++++++++++++++++--
drivers/mmc/host/sdhci.c | 28 +-
drivers/mmc/host/sdhci.h | 1 +
17 files changed, 739 insertions(+), 100 deletions(-)
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply
* [PATCH v8 01/16] clk: qcom: Add rcg ops to return floor value closest to the requested rate
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
From: Rajendra Nayak <rnayak@codeaurora.org>
The default behaviour with clk_rcg2_ops is for the
clk_round_rate()/clk_set_rate() to return/set a ceil clock
rate closest to the requested rate by looking up the corresponding
frequency table.
However, we do have some instances (mainly sdcc on various platforms)
of clients expecting a clk_set_rate() to set a floor value instead.
Add a new clk_rcg2_floor_ops to handle this for such specific
rcg instances
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
---
drivers/clk/qcom/clk-rcg.h | 1 +
drivers/clk/qcom/clk-rcg2.c | 76 +++++++++++++++++++++++++++++++++++++++------
drivers/clk/qcom/common.c | 16 ++++++++++
drivers/clk/qcom/common.h | 2 ++
4 files changed, 86 insertions(+), 9 deletions(-)
diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h
index b904c33..1b3e8d2 100644
--- a/drivers/clk/qcom/clk-rcg.h
+++ b/drivers/clk/qcom/clk-rcg.h
@@ -173,6 +173,7 @@ struct clk_rcg2 {
#define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr)
extern const struct clk_ops clk_rcg2_ops;
+extern const struct clk_ops clk_rcg2_floor_ops;
extern const struct clk_ops clk_rcg2_shared_ops;
extern const struct clk_ops clk_edp_pixel_ops;
extern const struct clk_ops clk_byte_ops;
diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c
index a071bba..1a0985a 100644
--- a/drivers/clk/qcom/clk-rcg2.c
+++ b/drivers/clk/qcom/clk-rcg2.c
@@ -47,6 +47,11 @@
#define N_REG 0xc
#define D_REG 0x10
+enum freq_policy {
+ FLOOR,
+ CEIL,
+};
+
static int clk_rcg2_is_enabled(struct clk_hw *hw)
{
struct clk_rcg2 *rcg = to_clk_rcg2(hw);
@@ -176,15 +181,26 @@ static int clk_rcg2_set_parent(struct clk_hw *hw, u8 index)
return calc_rate(parent_rate, m, n, mode, hid_div);
}
-static int _freq_tbl_determine_rate(struct clk_hw *hw,
- const struct freq_tbl *f, struct clk_rate_request *req)
+static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f,
+ struct clk_rate_request *req,
+ enum freq_policy policy)
{
unsigned long clk_flags, rate = req->rate;
struct clk_hw *p;
struct clk_rcg2 *rcg = to_clk_rcg2(hw);
int index;
- f = qcom_find_freq(f, rate);
+ switch (policy) {
+ case FLOOR:
+ f = qcom_find_freq_floor(f, rate);
+ break;
+ case CEIL:
+ f = qcom_find_freq(f, rate);
+ break;
+ default:
+ return -EINVAL;
+ };
+
if (!f)
return -EINVAL;
@@ -221,7 +237,15 @@ static int clk_rcg2_determine_rate(struct clk_hw *hw,
{
struct clk_rcg2 *rcg = to_clk_rcg2(hw);
- return _freq_tbl_determine_rate(hw, rcg->freq_tbl, req);
+ return _freq_tbl_determine_rate(hw, rcg->freq_tbl, req, CEIL);
+}
+
+static int clk_rcg2_determine_floor_rate(struct clk_hw *hw,
+ struct clk_rate_request *req)
+{
+ struct clk_rcg2 *rcg = to_clk_rcg2(hw);
+
+ return _freq_tbl_determine_rate(hw, rcg->freq_tbl, req, FLOOR);
}
static int clk_rcg2_configure(struct clk_rcg2 *rcg, const struct freq_tbl *f)
@@ -265,12 +289,23 @@ static int clk_rcg2_configure(struct clk_rcg2 *rcg, const struct freq_tbl *f)
return update_config(rcg);
}
-static int __clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate)
+static int __clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate,
+ enum freq_policy policy)
{
struct clk_rcg2 *rcg = to_clk_rcg2(hw);
const struct freq_tbl *f;
- f = qcom_find_freq(rcg->freq_tbl, rate);
+ switch (policy) {
+ case FLOOR:
+ f = qcom_find_freq_floor(rcg->freq_tbl, rate);
+ break;
+ case CEIL:
+ f = qcom_find_freq(rcg->freq_tbl, rate);
+ break;
+ default:
+ return -EINVAL;
+ };
+
if (!f)
return -EINVAL;
@@ -280,13 +315,25 @@ static int __clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate)
static int clk_rcg2_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
- return __clk_rcg2_set_rate(hw, rate);
+ return __clk_rcg2_set_rate(hw, rate, CEIL);
+}
+
+static int clk_rcg2_set_floor_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ return __clk_rcg2_set_rate(hw, rate, FLOOR);
}
static int clk_rcg2_set_rate_and_parent(struct clk_hw *hw,
unsigned long rate, unsigned long parent_rate, u8 index)
{
- return __clk_rcg2_set_rate(hw, rate);
+ return __clk_rcg2_set_rate(hw, rate, CEIL);
+}
+
+static int clk_rcg2_set_floor_rate_and_parent(struct clk_hw *hw,
+ unsigned long rate, unsigned long parent_rate, u8 index)
+{
+ return __clk_rcg2_set_rate(hw, rate, FLOOR);
}
const struct clk_ops clk_rcg2_ops = {
@@ -300,6 +347,17 @@ static int clk_rcg2_set_rate_and_parent(struct clk_hw *hw,
};
EXPORT_SYMBOL_GPL(clk_rcg2_ops);
+const struct clk_ops clk_rcg2_floor_ops = {
+ .is_enabled = clk_rcg2_is_enabled,
+ .get_parent = clk_rcg2_get_parent,
+ .set_parent = clk_rcg2_set_parent,
+ .recalc_rate = clk_rcg2_recalc_rate,
+ .determine_rate = clk_rcg2_determine_floor_rate,
+ .set_rate = clk_rcg2_set_floor_rate,
+ .set_rate_and_parent = clk_rcg2_set_floor_rate_and_parent,
+};
+EXPORT_SYMBOL_GPL(clk_rcg2_floor_ops);
+
static int clk_rcg2_shared_force_enable(struct clk_hw *hw, unsigned long rate)
{
struct clk_rcg2 *rcg = to_clk_rcg2(hw);
@@ -323,7 +381,7 @@ static int clk_rcg2_shared_force_enable(struct clk_hw *hw, unsigned long rate)
pr_err("%s: RCG did not turn on\n", name);
/* set clock rate */
- ret = __clk_rcg2_set_rate(hw, rate);
+ ret = __clk_rcg2_set_rate(hw, rate, CEIL);
if (ret)
return ret;
diff --git a/drivers/clk/qcom/common.c b/drivers/clk/qcom/common.c
index 94569f4..cfab7b4 100644
--- a/drivers/clk/qcom/common.c
+++ b/drivers/clk/qcom/common.c
@@ -46,6 +46,22 @@ struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, unsigned long rate)
}
EXPORT_SYMBOL_GPL(qcom_find_freq);
+const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
+ unsigned long rate)
+{
+ const struct freq_tbl *best = NULL;
+
+ for ( ; f->freq; f++) {
+ if (rate >= f->freq)
+ best = f;
+ else
+ break;
+ }
+
+ return best;
+}
+EXPORT_SYMBOL_GPL(qcom_find_freq_floor);
+
int qcom_find_src_index(struct clk_hw *hw, const struct parent_map *map, u8 src)
{
int i, num_parents = clk_hw_get_num_parents(hw);
diff --git a/drivers/clk/qcom/common.h b/drivers/clk/qcom/common.h
index 9fb5b8e..23c1927 100644
--- a/drivers/clk/qcom/common.h
+++ b/drivers/clk/qcom/common.h
@@ -41,6 +41,8 @@ struct qcom_cc_desc {
extern const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f,
unsigned long rate);
+extern const struct freq_tbl *qcom_find_freq_floor(const struct freq_tbl *f,
+ unsigned long rate);
extern void
qcom_pll_set_fsm_mode(struct regmap *m, u32 reg, u8 bias_count, u8 lock_count);
extern int qcom_find_src_index(struct clk_hw *hw, const struct parent_map *map,
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 02/16] clk: qcom: Move all sdcc rcgs to use clk_rcg2_floor_ops
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Rajendra Nayak <rnayak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
The sdcc driver for msm8996/msm8916/msm8974/msm8994 and apq8084
expects a clk_set_rate() on the sdcc rcg clk to set
a floor value of supported clk rate closest to the requested
rate, by looking up the frequency table.
So move all the sdcc rcgs on all these platforms to use the
newly introduced clk_rcg2_floor_ops
Signed-off-by: Rajendra Nayak <rnayak-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Jeremy McNicoll <jeremymc-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
drivers/clk/qcom/gcc-apq8084.c | 8 ++++----
drivers/clk/qcom/gcc-msm8916.c | 4 ++--
drivers/clk/qcom/gcc-msm8974.c | 8 ++++----
drivers/clk/qcom/gcc-msm8994.c | 8 ++++----
drivers/clk/qcom/gcc-msm8996.c | 8 ++++----
5 files changed, 18 insertions(+), 18 deletions(-)
diff --git a/drivers/clk/qcom/gcc-apq8084.c b/drivers/clk/qcom/gcc-apq8084.c
index 070037a..486d961 100644
--- a/drivers/clk/qcom/gcc-apq8084.c
+++ b/drivers/clk/qcom/gcc-apq8084.c
@@ -1142,7 +1142,7 @@ enum {
.name = "sdcc1_apps_clk_src",
.parent_names = gcc_xo_gpll0_gpll4,
.num_parents = 3,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -1156,7 +1156,7 @@ enum {
.name = "sdcc2_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -1170,7 +1170,7 @@ enum {
.name = "sdcc3_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -1184,7 +1184,7 @@ enum {
.name = "sdcc4_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c
index 5c4e193..628e6ca 100644
--- a/drivers/clk/qcom/gcc-msm8916.c
+++ b/drivers/clk/qcom/gcc-msm8916.c
@@ -1107,7 +1107,7 @@ enum {
.name = "sdcc1_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -1132,7 +1132,7 @@ enum {
.name = "sdcc2_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
diff --git a/drivers/clk/qcom/gcc-msm8974.c b/drivers/clk/qcom/gcc-msm8974.c
index 0091520..348e30d 100644
--- a/drivers/clk/qcom/gcc-msm8974.c
+++ b/drivers/clk/qcom/gcc-msm8974.c
@@ -872,7 +872,7 @@ enum {
.name = "sdcc1_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
};
static struct clk_rcg2 sdcc1_apps_clk_src = {
@@ -894,7 +894,7 @@ enum {
.name = "sdcc2_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -908,7 +908,7 @@ enum {
.name = "sdcc3_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -922,7 +922,7 @@ enum {
.name = "sdcc4_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
diff --git a/drivers/clk/qcom/gcc-msm8994.c b/drivers/clk/qcom/gcc-msm8994.c
index 84093c1..8afd830 100644
--- a/drivers/clk/qcom/gcc-msm8994.c
+++ b/drivers/clk/qcom/gcc-msm8994.c
@@ -912,7 +912,7 @@ enum {
.name = "sdcc1_apps_clk_src",
.parent_names = gcc_xo_gpll0_gpll4,
.num_parents = 3,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -938,7 +938,7 @@ enum {
.name = "sdcc2_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -953,7 +953,7 @@ enum {
.name = "sdcc3_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -968,7 +968,7 @@ enum {
.name = "sdcc4_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
diff --git a/drivers/clk/qcom/gcc-msm8996.c b/drivers/clk/qcom/gcc-msm8996.c
index e22bbc2..4b1fc17 100644
--- a/drivers/clk/qcom/gcc-msm8996.c
+++ b/drivers/clk/qcom/gcc-msm8996.c
@@ -460,7 +460,7 @@ enum {
.name = "sdcc1_apps_clk_src",
.parent_names = gcc_xo_gpll0_gpll4_gpll0_early_div,
.num_parents = 4,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -505,7 +505,7 @@ enum {
.name = "sdcc2_apps_clk_src",
.parent_names = gcc_xo_gpll0_gpll4,
.num_parents = 3,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -519,7 +519,7 @@ enum {
.name = "sdcc3_apps_clk_src",
.parent_names = gcc_xo_gpll0_gpll4,
.num_parents = 3,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
@@ -543,7 +543,7 @@ enum {
.name = "sdcc4_apps_clk_src",
.parent_names = gcc_xo_gpll0,
.num_parents = 2,
- .ops = &clk_rcg2_ops,
+ .ops = &clk_rcg2_floor_ops,
},
};
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 03/16] mmc: sdhci-msm: Change poor style writel/readl of registers
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-msm.c | 62 +++++++++++++++++++++++---------------------
1 file changed, 32 insertions(+), 30 deletions(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index b78d72f..2dcbeb0 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -138,9 +138,9 @@ static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
- /* Set CK_OUT_EN bit of DLL_CONFIG register to 1. */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- | CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
rc = msm_dll_poll_ck_out_en(host, 1);
@@ -307,6 +307,7 @@ static int msm_init_cm_dll(struct sdhci_host *host)
struct mmc_host *mmc = host->mmc;
int wait_cnt = 50;
unsigned long flags;
+ u32 config;
spin_lock_irqsave(&host->lock, flags);
@@ -315,33 +316,34 @@ static int msm_init_cm_dll(struct sdhci_host *host)
* tuning is in progress. Keeping PWRSAVE ON may
* turn off the clock.
*/
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC)
- & ~CORE_CLK_PWRSAVE), host->ioaddr + CORE_VENDOR_SPEC);
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+ config &= ~CORE_CLK_PWRSAVE;
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
- /* Write 1 to DLL_RST bit of DLL_CONFIG register */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- | CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
- /* Write 1 to DLL_PDN bit of DLL_CONFIG register */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- | CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
msm_cm_dll_set_freq(host);
- /* Write 0 to DLL_RST bit of DLL_CONFIG register */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- & ~CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config &= ~CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
- /* Write 0 to DLL_PDN bit of DLL_CONFIG register */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- & ~CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config &= ~CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
- /* Set DLL_EN bit to 1. */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- | CORE_DLL_EN), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_DLL_EN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
- /* Set CK_OUT_EN bit to 1. */
- writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
- | CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
/* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
while (!(readl_relaxed(host->ioaddr + CORE_DLL_STATUS) &
@@ -538,7 +540,7 @@ static int sdhci_msm_probe(struct platform_device *pdev)
struct resource *core_memres;
int ret;
u16 host_version, core_minor;
- u32 core_version, caps;
+ u32 core_version, config;
u8 core_major;
host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
@@ -606,9 +608,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
goto clk_disable;
}
- /* Reset the core and Enable SDHC mode */
- writel_relaxed(readl_relaxed(msm_host->core_mem + CORE_POWER) |
- CORE_SW_RST, msm_host->core_mem + CORE_POWER);
+ config = readl_relaxed(msm_host->core_mem + CORE_POWER);
+ config |= CORE_SW_RST;
+ writel_relaxed(config, msm_host->core_mem + CORE_POWER);
/* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
usleep_range(1000, 5000);
@@ -638,9 +640,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
* controller versions and must be explicitly enabled.
*/
if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
- caps = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
- caps |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
- writel_relaxed(caps, host->ioaddr +
+ config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
+ config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
+ writel_relaxed(config, host->ioaddr +
CORE_VENDOR_SPEC_CAPABILITIES0);
}
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 04/16] ARM: dts: Add xo_clock to sdhc nodes on qcom platforms
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
Add xo_clock to sdhc clock node on all qcom platforms.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
---
arch/arm/boot/dts/qcom-apq8084.dtsi | 16 ++++++++++------
arch/arm/boot/dts/qcom-msm8974.dtsi | 16 ++++++++++------
arch/arm64/boot/dts/qcom/msm8916.dtsi | 10 ++++++----
arch/arm64/boot/dts/qcom/msm8996.dtsi | 9 +++++----
4 files changed, 31 insertions(+), 20 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 39eb7a4..6857e42 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -182,13 +182,13 @@
};
clocks {
- xo_board {
+ xo_board: xo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
- sleep_clk {
+ sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
@@ -416,8 +416,10 @@
reg-names = "hc_mem", "core_mem";
interrupts = <0 123 0>, <0 138 0>;
interrupt-names = "hc_irq", "pwr_irq";
- clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
- clock-names = "core", "iface";
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
status = "disabled";
};
@@ -427,8 +429,10 @@
reg-names = "hc_mem", "core_mem";
interrupts = <0 125 0>, <0 221 0>;
interrupt-names = "hc_irq", "pwr_irq";
- clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
- clock-names = "core", "iface";
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+ <&gcc GCC_SDCC2_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
status = "disabled";
};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index d210947..947b7b1 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -220,13 +220,13 @@
};
clocks {
- xo_board {
+ xo_board: xo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
};
- sleep_clk {
+ sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
@@ -558,8 +558,10 @@
reg-names = "hc_mem", "core_mem";
interrupts = <0 123 0>, <0 138 0>;
interrupt-names = "hc_irq", "pwr_irq";
- clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
- clock-names = "core", "iface";
+ clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
status = "disabled";
};
@@ -569,8 +571,10 @@
reg-names = "hc_mem", "core_mem";
interrupts = <0 125 0>, <0 221 0>;
interrupt-names = "hc_irq", "pwr_irq";
- clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
- clock-names = "core", "iface";
+ clocks = <&gcc GCC_SDCC2_APPS_CLK>,
+ <&gcc GCC_SDCC2_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 466ca57..6265822 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -512,8 +512,9 @@
interrupts = <0 123 0>, <0 138 0>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC1_APPS_CLK>,
- <&gcc GCC_SDCC1_AHB_CLK>;
- clock-names = "core", "iface";
+ <&gcc GCC_SDCC1_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
bus-width = <8>;
non-removable;
status = "disabled";
@@ -527,8 +528,9 @@
interrupts = <0 125 0>, <0 221 0>;
interrupt-names = "hc_irq", "pwr_irq";
clocks = <&gcc GCC_SDCC2_APPS_CLK>,
- <&gcc GCC_SDCC2_AHB_CLK>;
- clock-names = "core", "iface";
+ <&gcc GCC_SDCC2_AHB_CLK>,
+ <&xo_board 0>;
+ clock-names = "core", "iface", "xo_clock";
bus-width = <4>;
status = "disabled";
};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 338f82a..73178fd 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -192,14 +192,14 @@
};
clocks {
- xo_board {
+ xo_board: xo_board {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <19200000>;
clock-output-names = "xo_board";
};
- sleep_clk {
+ sleep_clk: sleep_clk {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32764>;
@@ -347,9 +347,10 @@
interrupts = <0 125 0>, <0 221 0>;
interrupt-names = "hc_irq", "pwr_irq";
- clock-names = "iface", "core";
+ clock-names = "iface", "core", "xo_clock";
clocks = <&gcc GCC_SDCC2_AHB_CLK>,
- <&gcc GCC_SDCC2_APPS_CLK>;
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&xo_board 0>;
bus-width = <4>;
};
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 05/16] dt-bindings: sdhci-msm: Add xo_clock property
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
---
Documentation/devicetree/bindings/mmc/sdhci-msm.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index 485483a..243c9f0 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -17,6 +17,7 @@ Required properties:
"iface" - Main peripheral bus clock (PCLK/HCLK - AHB Bus clock) (required)
"core" - SDC MMC clock (MCLK) (required)
"bus" - SDCC bus voter clock (optional)
+ "xo_clock" - TCXO clock (optional)
Example:
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 06/16] mmc: sdhci-msm: Update DLL reset sequence
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Venkat Gopalakrishnan <venkatg-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Adrian Hunter <adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/mmc/host/sdhci-msm.c | 60 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 60 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 2dcbeb0..7e72105 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -59,6 +59,10 @@
#define CORE_DLL_CONFIG 0x100
#define CORE_DLL_STATUS 0x108
+#define CORE_DLL_CONFIG_2 0x1b4
+#define CORE_FLL_CYCLE_CNT BIT(18)
+#define CORE_DLL_CLOCK_DISABLE BIT(21)
+
#define CORE_VENDOR_SPEC 0x10c
#define CORE_CLK_PWRSAVE BIT(1)
@@ -77,7 +81,9 @@ struct sdhci_msm_host {
struct clk *clk; /* main SD/MMC bus clock */
struct clk *pclk; /* SDHC peripheral bus clock */
struct clk *bus_clk; /* SDHC bus voter clock */
+ struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/
struct mmc_host *mmc;
+ bool use_14lpp_dll_reset;
};
/* Platform specific tuning */
@@ -305,6 +311,8 @@ static inline void msm_cm_dll_set_freq(struct sdhci_host *host)
static int msm_init_cm_dll(struct sdhci_host *host)
{
struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
int wait_cnt = 50;
unsigned long flags;
u32 config;
@@ -320,6 +328,16 @@ static int msm_init_cm_dll(struct sdhci_host *host)
config &= ~CORE_CLK_PWRSAVE;
writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
+ if (msm_host->use_14lpp_dll_reset) {
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config &= ~CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2);
+ config |= CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2);
+ }
+
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
config |= CORE_DLL_RST;
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
@@ -329,6 +347,28 @@ static int msm_init_cm_dll(struct sdhci_host *host)
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
msm_cm_dll_set_freq(host);
+ if (msm_host->use_14lpp_dll_reset &&
+ !IS_ERR_OR_NULL(msm_host->xo_clk)) {
+ u32 mclk_freq = 0;
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2);
+ config &= CORE_FLL_CYCLE_CNT;
+ if (config)
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8),
+ clk_get_rate(msm_host->xo_clk));
+ else
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4),
+ clk_get_rate(msm_host->xo_clk));
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2);
+ config &= ~(0xFF << 10);
+ config |= mclk_freq << 10;
+
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2);
+ /* wait for 5us before enabling DLL clock */
+ udelay(5);
+ }
+
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
config &= ~CORE_DLL_RST;
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
@@ -337,6 +377,13 @@ static int msm_init_cm_dll(struct sdhci_host *host)
config &= ~CORE_DLL_PDN;
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+ if (msm_host->use_14lpp_dll_reset) {
+ msm_cm_dll_set_freq(host);
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2);
+ config &= ~CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2);
+ }
+
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
config |= CORE_DLL_EN;
writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
@@ -590,6 +637,16 @@ static int sdhci_msm_probe(struct platform_device *pdev)
goto pclk_disable;
}
+ /*
+ * xo_clock is needed for FLL feature of cm_dll.
+ * In case if xo_clock is not mentioned in DT, warn and proceed.
+ */
+ msm_host->xo_clk = devm_clk_get(&pdev->dev, "xo_clock");
+ if (IS_ERR(msm_host->xo_clk)) {
+ ret = PTR_ERR(msm_host->xo_clk);
+ dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret);
+ }
+
/* Vote for maximum clock rate for maximum performance */
ret = clk_set_rate(msm_host->clk, INT_MAX);
if (ret)
@@ -635,6 +692,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
core_version, core_major, core_minor);
+ if (core_major == 1 && core_minor >= 0x42)
+ msm_host->use_14lpp_dll_reset = true;
+
/*
* Support for some capabilities is not advertised by newer
* controller versions and must be explicitly enabled.
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 07/16] mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-msm.c | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 7e72105..518021d 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -68,6 +68,8 @@
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
+#define SDHCI_MSM_MIN_CLOCK 400000
+
#define CDR_SELEXT_SHIFT 20
#define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT)
#define CMUX_SHIFT_PHASE_SHIFT 24
@@ -556,6 +558,19 @@ static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data)
return IRQ_HANDLED;
}
+static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+
+ return clk_round_rate(msm_host->clk, ULONG_MAX);
+}
+
+static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
+{
+ return SDHCI_MSM_MIN_CLOCK;
+}
+
static const struct of_device_id sdhci_msm_dt_match[] = {
{ .compatible = "qcom,sdhci-msm-v4" },
{},
@@ -567,6 +582,8 @@ static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data)
.platform_execute_tuning = sdhci_msm_execute_tuning,
.reset = sdhci_reset,
.set_clock = sdhci_set_clock,
+ .get_min_clock = sdhci_msm_get_min_clock,
+ .get_max_clock = sdhci_msm_get_max_clock,
.set_bus_width = sdhci_set_bus_width,
.set_uhs_signaling = sdhci_msm_set_uhs_signaling,
.voltage_switch = sdhci_msm_voltage_switch,
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 08/16] mmc: sdhci-msm: Enable few quirks
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
sdhc-msm controller needs this SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN
& SDHCI_QUIRK2_PRESET_VALUE_BROKEN to be set. Hence setting it.
Signed-off-by: Sahitya Tummala <stummala-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Adrian Hunter <adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/mmc/host/sdhci-msm.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 518021d..45ead68 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -592,7 +592,9 @@ static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
static const struct sdhci_pltfm_data sdhci_msm_pdata = {
.quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
SDHCI_QUIRK_NO_CARD_NO_RESET |
- SDHCI_QUIRK_SINGLE_POWER_WRITE,
+ SDHCI_QUIRK_SINGLE_POWER_WRITE |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
.ops = &sdhci_msm_ops,
};
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 09/16] mmc: sdhci: Factor out sdhci_enable_clock
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Factor out sdhci_enable_clock from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/mmc/host/sdhci.c | 28 +++++++++++++++++-----------
drivers/mmc/host/sdhci.h | 1 +
2 files changed, 18 insertions(+), 11 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index d08d507..8a89d89 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -1344,20 +1344,10 @@ u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
}
EXPORT_SYMBOL_GPL(sdhci_calc_clk);
-void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
+void sdhci_enable_clock(struct sdhci_host *host, unsigned short clk)
{
- u16 clk;
unsigned long timeout;
- host->mmc->actual_clock = 0;
-
- sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
-
- if (clock == 0)
- return;
-
- clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
-
clk |= SDHCI_CLOCK_INT_EN;
sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
@@ -1378,6 +1368,22 @@ void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
clk |= SDHCI_CLOCK_CARD_EN;
sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
}
+EXPORT_SYMBOL_GPL(sdhci_enable_clock);
+
+void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ u16 clk;
+
+ host->mmc->actual_clock = 0;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
+ sdhci_enable_clock(host, clk);
+}
EXPORT_SYMBOL_GPL(sdhci_set_clock);
static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 766df17..8e77a3b 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -681,6 +681,7 @@ static inline bool sdhci_sdio_irq_enabled(struct sdhci_host *host)
u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
unsigned int *actual_clock);
void sdhci_set_clock(struct sdhci_host *host, unsigned int clock);
+void sdhci_enable_clock(struct sdhci_host *host, unsigned short clk);
void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
unsigned short vdd);
void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 10/16] mmc: sdhci-msm: Implement set_clock callback for sdhci-msm
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Adrian Hunter <adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/mmc/host/sdhci-msm.c | 66 +++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 65 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 45ead68..6d02fc2 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -84,6 +84,7 @@ struct sdhci_msm_host {
struct clk *pclk; /* SDHC peripheral bus clock */
struct clk *bus_clk; /* SDHC bus voter clock */
struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/
+ unsigned long clk_rate;
struct mmc_host *mmc;
bool use_14lpp_dll_reset;
};
@@ -571,6 +572,69 @@ static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
return SDHCI_MSM_MIN_CLOCK;
}
+/**
+ * __sdhci_msm_set_clock - sdhci_msm clock control.
+ *
+ * Description:
+ * MSM controller does not use internal divider and
+ * instead directly control the GCC clock as per
+ * HW recommendation.
+ **/
+void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ u16 clk;
+ /*
+ * Keep actual_clock as zero -
+ * - since there is no divider used so no need of having actual_clock.
+ * - MSM controller uses SDCLK for data timeout calculation. If
+ * actual_clock is zero, host->clock is taken for calculation.
+ */
+ host->mmc->actual_clock = 0;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ /*
+ * MSM controller do not use clock divider.
+ * Thus read SDHCI_CLOCK_CONTROL and only enable
+ * clock with no divider value programmed.
+ */
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ sdhci_enable_clock(host, clk);
+}
+
+/* sdhci_msm_set_clock - Called with (host->lock) spinlock held. */
+static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ int rc;
+
+ if (!clock) {
+ msm_host->clk_rate = clock;
+ goto out;
+ }
+
+ spin_unlock_irq(&host->lock);
+
+ rc = clk_set_rate(msm_host->clk, clock);
+ if (rc) {
+ pr_err("%s: Failed to set clock at rate %u\n",
+ mmc_hostname(host->mmc), clock);
+ goto out_lock;
+ }
+ msm_host->clk_rate = clock;
+ pr_debug("%s: Setting clock at rate %lu\n",
+ mmc_hostname(host->mmc), clk_get_rate(msm_host->clk));
+
+out_lock:
+ spin_lock_irq(&host->lock);
+out:
+ __sdhci_msm_set_clock(host, clock);
+}
+
static const struct of_device_id sdhci_msm_dt_match[] = {
{ .compatible = "qcom,sdhci-msm-v4" },
{},
@@ -581,7 +645,7 @@ static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
static const struct sdhci_ops sdhci_msm_ops = {
.platform_execute_tuning = sdhci_msm_execute_tuning,
.reset = sdhci_reset,
- .set_clock = sdhci_set_clock,
+ .set_clock = sdhci_msm_set_clock,
.get_min_clock = sdhci_msm_get_min_clock,
.get_max_clock = sdhci_msm_get_max_clock,
.set_bus_width = sdhci_set_bus_width,
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 11/16] mmc: sdhci-msm: Add clock changes for DDR mode.
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-msm.c | 21 +++++++++++++++++----
1 file changed, 17 insertions(+), 4 deletions(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 6d02fc2..eb29b97 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -610,6 +610,7 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_ios curr_ios = host->mmc->ios;
int rc;
if (!clock) {
@@ -618,16 +619,28 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
}
spin_unlock_irq(&host->lock);
+ /*
+ * The SDHC requires internal clock frequency to be double the
+ * actual clock that will be set for DDR mode. The controller
+ * uses the faster clock(100/400MHz) for some of its parts and
+ * send the actual required clock (50/200MHz) to the card.
+ */
+ if (curr_ios.timing == MMC_TIMING_UHS_DDR50 ||
+ curr_ios.timing == MMC_TIMING_MMC_DDR52 ||
+ curr_ios.timing == MMC_TIMING_MMC_HS400)
+ clock *= 2;
rc = clk_set_rate(msm_host->clk, clock);
if (rc) {
- pr_err("%s: Failed to set clock at rate %u\n",
- mmc_hostname(host->mmc), clock);
+ pr_err("%s: Failed to set clock at rate %u at timing %d\n",
+ mmc_hostname(host->mmc), clock,
+ curr_ios.timing);
goto out_lock;
}
msm_host->clk_rate = clock;
- pr_debug("%s: Setting clock at rate %lu\n",
- mmc_hostname(host->mmc), clk_get_rate(msm_host->clk));
+ pr_debug("%s: Setting clock at rate %lu at timing %d\n",
+ mmc_hostname(host->mmc), clk_get_rate(msm_host->clk),
+ curr_ios.timing);
out_lock:
spin_lock_irq(&host->lock);
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 12/16] arm64: dts: qcom: msm8916: Add ddr support to sdhc1
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
This adds mmc-ddr-1_8v support to DT for sdhc1 of msm8916.
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 6265822..5bc187c 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -515,6 +515,7 @@
<&gcc GCC_SDCC1_AHB_CLK>,
<&xo_board 0>;
clock-names = "core", "iface", "xo_clock";
+ mmc-ddr-1_8v;
bus-width = <8>;
non-removable;
status = "disabled";
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 13/16] mmc: sdhci-msm: Add HS400 platform support
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Venkat Gopalakrishnan <venkatg-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Adrian Hunter <adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/mmc/host/sdhci-msm.c | 122 +++++++++++++++++++++++++++++++++++++++----
1 file changed, 112 insertions(+), 10 deletions(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index eb29b97..ab59171 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -32,6 +32,7 @@
#define HC_MODE_EN 0x1
#define CORE_POWER 0x0
#define CORE_SW_RST BIT(7)
+#define FF_CLK_SW_RST_DIS BIT(13)
#define CORE_PWRCTL_STATUS 0xdc
#define CORE_PWRCTL_MASK 0xe0
@@ -65,10 +66,17 @@
#define CORE_VENDOR_SPEC 0x10c
#define CORE_CLK_PWRSAVE BIT(1)
+#define CORE_HC_MCLK_SEL_DFLT (2 << 8)
+#define CORE_HC_MCLK_SEL_HS400 (3 << 8)
+#define CORE_HC_MCLK_SEL_MASK (3 << 8)
+#define CORE_HC_SELECT_IN_EN BIT(18)
+#define CORE_HC_SELECT_IN_HS400 (6 << 19)
+#define CORE_HC_SELECT_IN_MASK (7 << 19)
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
#define SDHCI_MSM_MIN_CLOCK 400000
+#define CORE_FREQ_100MHZ (100 * 1000 * 1000)
#define CDR_SELEXT_SHIFT 20
#define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT)
@@ -87,6 +95,8 @@ struct sdhci_msm_host {
unsigned long clk_rate;
struct mmc_host *mmc;
bool use_14lpp_dll_reset;
+ bool tuning_done;
+ bool calibration_done;
};
/* Platform specific tuning */
@@ -174,8 +184,8 @@ static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
* Find out the greatest range of consecuitive selected
* DLL clock output phases that can be used as sampling
* setting for SD3.0 UHS-I card read operation (in SDR104
- * timing mode) or for eMMC4.5 card read operation (in HS200
- * timing mode).
+ * timing mode) or for eMMC4.5 card read operation (in
+ * HS400/HS200 timing mode).
* Select the 3/4 of the range and configure the DLL with the
* selected DLL clock output phase.
*/
@@ -424,9 +434,10 @@ static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
* Tuning is required for SDR104, HS200 and HS400 cards and
* if clock frequency is greater than 100MHz in these modes.
*/
- if (host->clock <= 100 * 1000 * 1000 ||
- !((ios.timing == MMC_TIMING_MMC_HS200) ||
- (ios.timing == MMC_TIMING_UHS_SDR104)))
+ if (host->clock <= CORE_FREQ_100MHZ ||
+ !(ios.timing == MMC_TIMING_MMC_HS400 ||
+ ios.timing == MMC_TIMING_MMC_HS200 ||
+ ios.timing == MMC_TIMING_UHS_SDR104))
return 0;
retry:
@@ -477,6 +488,8 @@ static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
rc = -EIO;
}
+ if (!rc)
+ msm_host->tuning_done = true;
return rc;
}
@@ -484,7 +497,10 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
unsigned int uhs)
{
struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
u16 ctrl_2;
+ u32 config;
ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
/* Select Bus Speed Mode for host */
@@ -499,6 +515,7 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
case MMC_TIMING_UHS_SDR50:
ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
break;
+ case MMC_TIMING_MMC_HS400:
case MMC_TIMING_MMC_HS200:
case MMC_TIMING_UHS_SDR104:
ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
@@ -515,11 +532,29 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
* provide feedback clock, the mode selection can be any value less
* than 3'b011 in bits [2:0] of HOST CONTROL2 register.
*/
- if (host->clock <= 100000000 &&
- (uhs == MMC_TIMING_MMC_HS400 ||
- uhs == MMC_TIMING_MMC_HS200 ||
- uhs == MMC_TIMING_UHS_SDR104))
- ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ if (host->clock <= CORE_FREQ_100MHZ) {
+ if (uhs == MMC_TIMING_MMC_HS400 ||
+ uhs == MMC_TIMING_MMC_HS200 ||
+ uhs == MMC_TIMING_UHS_SDR104)
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ /*
+ * DLL is not required for clock <= 100MHz
+ * Thus, make sure DLL it is disabled when not required
+ */
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+
+ /*
+ * The DLL needs to be restored and CDCLP533 recalibrated
+ * when the clock frequency is set back to 400MHz.
+ */
+ msm_host->calibration_done = false;
+ }
dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
@@ -611,6 +646,7 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
struct mmc_ios curr_ios = host->mmc->ios;
+ u32 config;
int rc;
if (!clock) {
@@ -629,6 +665,68 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
curr_ios.timing == MMC_TIMING_MMC_DDR52 ||
curr_ios.timing == MMC_TIMING_MMC_HS400)
clock *= 2;
+ /*
+ * In general all timing modes are controlled via UHS mode select in
+ * Host Control2 register. eMMC specific HS200/HS400 doesn't have
+ * their respective modes defined here, hence we use these values.
+ *
+ * HS200 - SDR104 (Since they both are equivalent in functionality)
+ * HS400 - This involves multiple configurations
+ * Initially SDR104 - when tuning is required as HS200
+ * Then when switching to DDR @ 400MHz (HS400) we use
+ * the vendor specific HC_SELECT_IN to control the mode.
+ *
+ * In addition to controlling the modes we also need to select the
+ * correct input clock for DLL depending on the mode.
+ *
+ * HS400 - divided clock (free running MCLK/2)
+ * All other modes - default (free running MCLK)
+ */
+ if (curr_ios.timing == MMC_TIMING_MMC_HS400) {
+ /* Select the divided clock (free running MCLK/2) */
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_HS400;
+
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
+ /*
+ * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC
+ * register
+ */
+ if (msm_host->tuning_done && !msm_host->calibration_done) {
+ /*
+ * Write 0x6 to HC_SELECT_IN and 1 to HC_SELECT_IN_EN
+ * field in VENDOR_SPEC_FUNC
+ */
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+ config |= CORE_HC_SELECT_IN_HS400;
+ config |= CORE_HC_SELECT_IN_EN;
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
+ }
+ } else {
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_DFLT;
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
+
+ /*
+ * Disable HC_SELECT_IN to be able to use the UHS mode select
+ * configuration from Host Control2 register for all other
+ * modes.
+ * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field
+ * in VENDOR_SPEC_FUNC
+ */
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+ config &= ~CORE_HC_SELECT_IN_EN;
+ config &= ~CORE_HC_SELECT_IN_MASK;
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
+ }
+
+ /*
+ * Make sure above writes impacting free running MCLK are completed
+ * before changing the clk_rate at GCC.
+ */
+ wmb();
rc = clk_set_rate(msm_host->clk, clock);
if (rc) {
@@ -776,6 +874,10 @@ static int sdhci_msm_probe(struct platform_device *pdev)
/* Set HC_MODE_EN bit in HC_MODE register */
writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE));
+ config = readl_relaxed(msm_host->core_mem + CORE_HC_MODE);
+ config |= FF_CLK_SW_RST_DIS;
+ writel_relaxed(config, msm_host->core_mem + CORE_HC_MODE);
+
host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v8 14/16] mmc: sdhci-msm: Save the calculated tuning phase
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-msm.c | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index ab59171..1556d45 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -75,6 +75,7 @@
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
+#define INVALID_TUNING_PHASE -1
#define SDHCI_MSM_MIN_CLOCK 400000
#define CORE_FREQ_100MHZ (100 * 1000 * 1000)
@@ -97,6 +98,7 @@ struct sdhci_msm_host {
bool use_14lpp_dll_reset;
bool tuning_done;
bool calibration_done;
+ u8 saved_tuning_phase;
};
/* Platform specific tuning */
@@ -136,6 +138,9 @@ static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
u32 config;
struct mmc_host *mmc = host->mmc;
+ if (phase > 0xf)
+ return -EINVAL;
+
spin_lock_irqsave(&host->lock, flags);
config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
@@ -429,6 +434,8 @@ static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
int rc;
struct mmc_host *mmc = host->mmc;
struct mmc_ios ios = host->mmc->ios;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
/*
* Tuning is required for SDR104, HS200 and HS400 cards and
@@ -453,6 +460,7 @@ static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
if (rc)
return rc;
+ msm_host->saved_tuning_phase = phase;
rc = mmc_send_tuning(mmc, opcode, NULL);
if (!rc) {
/* Tuning is successful at this tuning point */
@@ -799,6 +807,8 @@ static int sdhci_msm_probe(struct platform_device *pdev)
sdhci_get_of_property(pdev);
+ msm_host->saved_tuning_phase = INVALID_TUNING_PHASE;
+
/* Setup SDCC bus voter clock. */
msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
if (!IS_ERR(msm_host->bus_clk)) {
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 15/16] mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson, linux-mmc, adrian.hunter, sboyd, andy.gross
Cc: shawn.lin, devicetree, linux-clk, david.brown, linux-arm-msm,
georgi.djakov, alex.lemberg, mateusz.nowak, Yuliy.Izrailov,
asutoshd, david.griego, stummala, venkatg, rnayak, pramod.gurav,
jeremymc, Ritesh Harjani
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
drivers/mmc/host/sdhci-msm.c | 151 +++++++++++++++++++++++++++++++++++++++++++
1 file changed, 151 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 1556d45..47379f4 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -20,6 +20,7 @@
#include <linux/mmc/mmc.h>
#include <linux/pm_runtime.h>
#include <linux/slab.h>
+#include <linux/iopoll.h>
#include "sdhci-pltfm.h"
@@ -58,6 +59,7 @@
#define CORE_DLL_PDN BIT(29)
#define CORE_DLL_RST BIT(30)
#define CORE_DLL_CONFIG 0x100
+#define CORE_CMD_DAT_TRACK_SEL BIT(0)
#define CORE_DLL_STATUS 0x108
#define CORE_DLL_CONFIG_2 0x1b4
@@ -73,6 +75,33 @@
#define CORE_HC_SELECT_IN_HS400 (6 << 19)
#define CORE_HC_SELECT_IN_MASK (7 << 19)
+#define CORE_CSR_CDC_CTLR_CFG0 0x130
+#define CORE_SW_TRIG_FULL_CALIB BIT(16)
+#define CORE_HW_AUTOCAL_ENA BIT(17)
+
+#define CORE_CSR_CDC_CTLR_CFG1 0x134
+#define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138
+#define CORE_TIMER_ENA BIT(16)
+
+#define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C
+#define CORE_CSR_CDC_REFCOUNT_CFG 0x140
+#define CORE_CSR_CDC_COARSE_CAL_CFG 0x144
+#define CORE_CDC_OFFSET_CFG 0x14C
+#define CORE_CSR_CDC_DELAY_CFG 0x150
+#define CORE_CDC_SLAVE_DDA_CFG 0x160
+#define CORE_CSR_CDC_STATUS0 0x164
+#define CORE_CALIBRATION_DONE BIT(0)
+
+#define CORE_CDC_ERROR_CODE_MASK 0x7000000
+
+#define CORE_CSR_CDC_GEN_CFG 0x178
+#define CORE_CDC_SWITCH_BYPASS_OFF BIT(0)
+#define CORE_CDC_SWITCH_RC_EN BIT(1)
+
+#define CORE_DDR_200_CFG 0x184
+#define CORE_CDC_T4_DLY_SEL BIT(0)
+#define CORE_START_CDC_TRAFFIC BIT(6)
+
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
#define INVALID_TUNING_PHASE -1
@@ -427,6 +456,119 @@ static int msm_init_cm_dll(struct sdhci_host *host)
return 0;
}
+static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ u32 config, calib_done;
+ int ret;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ /* Set the selected phase in delay line hw block */
+ ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+
+ config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG);
+ config &= ~CORE_CDC_T4_DLY_SEL;
+ writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config &= ~CORE_CDC_SWITCH_BYPASS_OFF;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config |= CORE_CDC_SWITCH_RC_EN;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG);
+ config &= ~CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG);
+
+ /*
+ * Perform CDC Register Initialization Sequence
+ *
+ * CORE_CSR_CDC_CTLR_CFG0 0x11800EC
+ * CORE_CSR_CDC_CTLR_CFG1 0x3011111
+ * CORE_CSR_CDC_CAL_TIMER_CFG0 0x1201000
+ * CORE_CSR_CDC_CAL_TIMER_CFG1 0x4
+ * CORE_CSR_CDC_REFCOUNT_CFG 0xCB732020
+ * CORE_CSR_CDC_COARSE_CAL_CFG 0xB19
+ * CORE_CSR_CDC_DELAY_CFG 0x3AC
+ * CORE_CDC_OFFSET_CFG 0x0
+ * CORE_CDC_SLAVE_DDA_CFG 0x16334
+ */
+
+ writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1);
+ writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1);
+ writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG);
+ writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG);
+ writel_relaxed(0x3AC, host->ioaddr + CORE_CSR_CDC_DELAY_CFG);
+ writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG);
+ writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG);
+
+ /* CDC HW Calibration */
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config &= ~CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_HW_AUTOCAL_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ config |= CORE_TIMER_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0,
+ calib_done,
+ (calib_done & CORE_CALIBRATION_DONE),
+ 1, 50);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CDC calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0)
+ & CORE_CDC_ERROR_CODE_MASK;
+ if (ret) {
+ pr_err("%s: %s: CDC error code %d\n",
+ mmc_hostname(host->mmc), __func__, ret);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ config = readl_relaxed(host->ioaddr + CORE_DDR_200_CFG);
+ config |= CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + CORE_DDR_200_CFG);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
{
int tuning_seq_cnt = 3;
@@ -567,6 +709,15 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+ spin_unlock_irq(&host->lock);
+ /* CDCLP533 HW calibration is only required for HS400 mode*/
+ if (host->clock > CORE_FREQ_100MHZ &&
+ msm_host->tuning_done && !msm_host->calibration_done &&
+ mmc->ios.timing == MMC_TIMING_MMC_HS400)
+ if (!sdhci_msm_cdclp533_calibration(host))
+ msm_host->calibration_done = true;
+ spin_lock_irq(&host->lock);
}
static void sdhci_msm_voltage_switch(struct sdhci_host *host)
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
^ permalink raw reply related
* [PATCH v8 16/16] sdhci: sdhci-msm: update dll configuration
From: Ritesh Harjani @ 2016-11-16 16:00 UTC (permalink / raw)
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
adrian.hunter-ral2JQCrhuEAvxtiuMwx3w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, andy.gross-QSEj5FYQhm4dnm+yROfE0A
Cc: shawn.lin-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
david.brown-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
georgi.djakov-QSEj5FYQhm4dnm+yROfE0A,
alex.lemberg-XdAiOPVOjttBDgjK7y7TUQ,
mateusz.nowak-ral2JQCrhuEAvxtiuMwx3w,
Yuliy.Izrailov-XdAiOPVOjttBDgjK7y7TUQ,
asutoshd-sgV2jX0FEOL9JmXXK+q4OQ,
david.griego-QSEj5FYQhm4dnm+yROfE0A,
stummala-sgV2jX0FEOL9JmXXK+q4OQ, venkatg-sgV2jX0FEOL9JmXXK+q4OQ,
rnayak-sgV2jX0FEOL9JmXXK+q4OQ,
pramod.gurav-QSEj5FYQhm4dnm+yROfE0A,
jeremymc-H+wXaHxf7aLQT0dZR+AlfA, Ritesh Harjani, Krishna Konda
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Krishna Konda <kkonda-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Acked-by: Adrian Hunter <adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
---
drivers/mmc/host/sdhci-msm.c | 125 ++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 123 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index 47379f4..49907f4 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -52,6 +52,7 @@
#define INT_MASK 0xf
#define MAX_PHASES 16
#define CORE_DLL_LOCK BIT(7)
+#define CORE_DDR_DLL_LOCK BIT(11)
#define CORE_DLL_EN BIT(16)
#define CORE_CDR_EN BIT(17)
#define CORE_CK_OUT_EN BIT(18)
@@ -63,6 +64,7 @@
#define CORE_DLL_STATUS 0x108
#define CORE_DLL_CONFIG_2 0x1b4
+#define CORE_DDR_CAL_EN BIT(0)
#define CORE_FLL_CYCLE_CNT BIT(18)
#define CORE_DLL_CLOCK_DISABLE BIT(21)
@@ -101,6 +103,11 @@
#define CORE_DDR_200_CFG 0x184
#define CORE_CDC_T4_DLY_SEL BIT(0)
#define CORE_START_CDC_TRAFFIC BIT(6)
+#define CORE_VENDOR_SPEC3 0x1b0
+#define CORE_PWRSAVE_DLL BIT(3)
+
+#define CORE_DDR_CONFIG 0x1b8
+#define DDR_CONFIG_POR_VAL 0x80040853
#define CORE_VENDOR_SPEC_CAPABILITIES0 0x11c
@@ -128,6 +135,7 @@ struct sdhci_msm_host {
bool tuning_done;
bool calibration_done;
u8 saved_tuning_phase;
+ bool use_cdclp533;
};
/* Platform specific tuning */
@@ -569,6 +577,87 @@ static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
return ret;
}
+static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
+{
+ u32 dll_status, config;
+ int ret;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Currently the CORE_DDR_CONFIG register defaults to desired
+ * configuration on reset. Currently reprogramming the power on
+ * reset (POR) value in case it might have been modified by
+ * bootloaders. In the future, if this changes, then the desired
+ * values will need to be programmed appropriately.
+ */
+ writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + CORE_DDR_CONFIG);
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG_2);
+ config |= CORE_DDR_CAL_EN;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG_2);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_DLL_STATUS,
+ dll_status,
+ (dll_status & CORE_DDR_DLL_LOCK),
+ 10, 1000);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC3);
+ config |= CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC3);
+
+ /*
+ * Drain writebuffer to ensure above DLL calibration
+ * and PWRSAVE DLL is enabled.
+ */
+ wmb();
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+ u32 config;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ /* Set the selected phase in delay line hw block */
+ ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+
+ config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
+ if (msm_host->use_cdclp533)
+ ret = sdhci_msm_cdclp533_calibration(host);
+ else
+ ret = sdhci_msm_cm_dll_sdc4_calibration(host);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
{
int tuning_seq_cnt = 3;
@@ -715,7 +804,7 @@ static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
if (host->clock > CORE_FREQ_100MHZ &&
msm_host->tuning_done && !msm_host->calibration_done &&
mmc->ios.timing == MMC_TIMING_MMC_HS400)
- if (!sdhci_msm_cdclp533_calibration(host))
+ if (!sdhci_msm_hs400_dll_calibration(host))
msm_host->calibration_done = true;
spin_lock_irq(&host->lock);
}
@@ -805,7 +894,7 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
struct mmc_ios curr_ios = host->mmc->ios;
- u32 config;
+ u32 config, dll_lock;
int rc;
if (!clock) {
@@ -862,7 +951,32 @@ static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
config |= CORE_HC_SELECT_IN_EN;
writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
}
+ if (!msm_host->clk_rate && !msm_host->use_cdclp533) {
+ /*
+ * Poll on DLL_LOCK or DDR_DLL_LOCK bits in
+ * CORE_DLL_STATUS to be set. This should get set
+ * within 15 us at 200 MHz.
+ */
+ rc = readl_relaxed_poll_timeout(host->ioaddr +
+ CORE_DLL_STATUS,
+ dll_lock,
+ (dll_lock &
+ (CORE_DLL_LOCK |
+ CORE_DDR_DLL_LOCK)), 10,
+ 1000);
+ if (rc == -ETIMEDOUT)
+ pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n",
+ mmc_hostname(host->mmc), dll_lock);
+ }
} else {
+ if (!msm_host->use_cdclp533) {
+ config = readl_relaxed(host->ioaddr +
+ CORE_VENDOR_SPEC3);
+ config &= ~CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr +
+ CORE_VENDOR_SPEC3);
+ }
+
config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
config &= ~CORE_HC_MCLK_SEL_MASK;
config |= CORE_HC_MCLK_SEL_DFLT;
@@ -1055,6 +1169,13 @@ static int sdhci_msm_probe(struct platform_device *pdev)
msm_host->use_14lpp_dll_reset = true;
/*
+ * SDCC 5 controller with major version 1, minor version 0x34 and later
+ * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL.
+ */
+ if (core_major == 1 && core_minor < 0x34)
+ msm_host->use_cdclp533 = true;
+
+ /*
* Support for some capabilities is not advertised by newer
* controller versions and must be explicitly enabled.
*/
--
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH] net: ethernet: faraday: To support device tree usage.
From: Arnd Bergmann @ 2016-11-16 16:12 UTC (permalink / raw)
To: Andrew Lunn; +Cc: Greentime Hu, netdev, devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161116143715.GH19962-g2DYL2Zd6BY@public.gmane.org>
On Wednesday, November 16, 2016 3:37:15 PM CET Andrew Lunn wrote:
> On Wed, Nov 16, 2016 at 10:26:52PM +0800, Greentime Hu wrote:
> > On Wed, Nov 16, 2016 at 9:47 PM, Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org> wrote:
> > > On Wed, Nov 16, 2016 at 04:43:15PM +0800, Greentime Hu wrote:
> > >> To support device tree usage for ftmac100.
> > >>
> > >> Signed-off-by: Greentime Hu <green.hu-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> > >> ---
> > >> drivers/net/ethernet/faraday/ftmac100.c | 7 +++++++
> > >> 1 file changed, 7 insertions(+)
> > >>
> > >> diff --git a/drivers/net/ethernet/faraday/ftmac100.c b/drivers/net/ethernet/faraday/ftmac100.c
> > >> index dce5f7b..81dd9e1 100644
> > >> --- a/drivers/net/ethernet/faraday/ftmac100.c
> > >> +++ b/drivers/net/ethernet/faraday/ftmac100.c
> > >> @@ -1172,11 +1172,17 @@ static int __exit ftmac100_remove(struct platform_device *pdev)
> > >> return 0;
> > >> }
> > >>
> > >> +static const struct of_device_id mac_of_ids[] = {
> > >> + { .compatible = "andestech,atmac100" },
> > >> + { }
> > >
> > > andestech is not in
> > > Documentation/devicetree/bindings/vendor-prefixes.txt Please provide a
> > > separate patch adding it.
> > OK. I will provide another patch to add andestech.
> >
> > > Humm, why andestech? Why not something based around faraday
> > > technology?
> > It is because we use the same ftmac100 IP provided from faraday
> > technology but I am now using it in andestech SoC.
>
> Please make sure you get an acked-by: from the device tree
> maintainers. They might want you to use faraday, since that is the
> original IP provider. For example, all Synopsys licensed IP uses
> "snps,XXX", not the SoC vendor with the license.
I think ideally we have both the ID from andes and from faraday here.
Note that we already have "moxa,moxart-mac" as a compatible string
for this hardware, though it uses a different driver.
We should probably have a single binding document describing
both compatible strings and any optional properties.
Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v5] PCI: qcom: add support to msm8996 PCIE controller
From: Srinivas Kandagatla @ 2016-11-16 16:29 UTC (permalink / raw)
To: Rob Herring; +Cc: svarbanov, linux-pci, bhelgaas, linux-arm-msm, devicetree
In-Reply-To: <20161116150858.343voujjg4p2zdhn@rob-hp-laptop>
On 16/11/16 15:08, Rob Herring wrote:
> On Tue, Nov 15, 2016 at 02:23:57PM +0000, Srinivas Kandagatla wrote:
>> This patch adds support to msm8996/apq8096 pcie, MSM8996 supports
>
> s/pcie/PCIe/
Will fix two instances this and spin a next version.
>
>> Gen 1/2, One lane, 3 pcie root-complex with support to MSI and
>> legacy interrupts and it conforms to PCI Express Base 2.1 specification.
>>
>> This patch adds post_init callback to qcom_pcie_ops, as this is pcie
>
> s/pcie/PCIe/
>
>> pipe clocks are only setup after the phy is powered on.
>> It also adds ltssm_enable callback as it is very much different to other
>> supported SOCs in the driver.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
>> ---
>>
>> Changes since v4:
>> - removed duplicate define spotted by Stan.
>> - renamed halt register to remove msm8996 suggested by Stan.
>> - dropped simple-pm-bus and runtime pm patches as these can
>> potentially go into pm domain provider.
>>
>> .../devicetree/bindings/pci/qcom,pcie.txt | 67 +++++++-
>> drivers/pci/host/pcie-qcom.c | 175 ++++++++++++++++++++-
>> 2 files changed, 236 insertions(+), 6 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
>> index 4059a6f..141d8c3 100644
>> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
>> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
>> @@ -7,6 +7,7 @@
>> - "qcom,pcie-ipq8064" for ipq8064
>> - "qcom,pcie-apq8064" for apq8064
>> - "qcom,pcie-apq8084" for apq8084
>> + - "qcom,pcie-msm8996" for msm8996 or apq8096
>>
>> - reg:
>> Usage: required
>> @@ -92,6 +93,17 @@
>> - "aux" Auxiliary (AUX) clock
>> - "bus_master" Master AXI clock
>> - "bus_slave" Slave AXI clock
>> +
>> +- clock-names:
>> + Usage: required for msm8996/apq8096
>> + Value type: <stringlist>
>> + Definition: Should contain the following entries
>> + - "pipe" Pipe Clock driving internal logic.
>> + - "aux" Auxiliary (AUX) clock.
>> + - "cfg" Configuration clk.
>> + - "bus_master" Master AXI clock.
>> + - "bus_slave" Slave AXI clock.
>> +
>> - resets:
>> Usage: required
>> Value type: <prop-encoded-array>
>> @@ -115,7 +127,7 @@
>> - "core" Core reset
>>
>> - power-domains:
>> - Usage: required for apq8084
>> + Usage: required for apq8084 and msm8996/apq8096
>> Value type: <prop-encoded-array>
>> Definition: A phandle and power domain specifier pair to the
>> power domain which is responsible for collapsing
>> @@ -231,3 +243,56 @@
>> pinctrl-0 = <&pcie0_pins_default>;
>> pinctrl-names = "default";
>> };
>> +
>> +* Example for apq8096:
>
> Do you really need an example for every chip?
Yes, for consistency reasons, as there are two examples already in this
document. Also having an example does not harm anyway.
thanks,
srini
>
>> +
>> + pcie@608000{
>> + compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
>> + power-domains = <&gcc PCIE1_GDSC>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <1>;
>> +
>> + reg = <0x00608000 0x2000>,
>> + <0x0d000000 0xf1d>,
>> + <0x0d000f20 0xa8>,
>> + <0x0d100000 0x100000>;
>> +
>> + reg-names = "parf", "dbi", "elbi", "config";
>> +
>> + phys = <&pcie_phy 1>;
>> + phy-names = "pciephy";
>> +
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
>> + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
>> +
>> + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>;
>> + interrupt-names = "msi";
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>> + pinctrl-names = "default", "sleep";
>> + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
>> + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
>> +
>> + vdda-1p8-supply = <&pm8994_l12>;
>> + vdda-supply = <&pm8994_l28>;
>> + linux,pci-domain = <1>;
>> +
>> + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
>> + <&gcc GCC_PCIE_1_AUX_CLK>,
>> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
>> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
>> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>;
>> +
>> + clock-names = "pipe",
>> + "aux",
>> + "cfg",
>> + "bus_master",
>> + "bus_slave";
>> + };
^ permalink raw reply
* Re: [PATCH v4 1/3] bus: simple-pm: add support to pm clocks
From: Srinivas Kandagatla @ 2016-11-16 16:33 UTC (permalink / raw)
To: Nayak, Rajendra, Geert Uytterhoeven, Bjorn Helgaas
Cc: svarbanov, linux-pci, Bjorn Helgaas, Rob Herring,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
Geert Uytterhoeven, Kevin Hilman, Simon Horman, Linux PM list,
Nayak, Rajendra
In-Reply-To: <d1bc3663-5824-32f8-a20f-1c5e28466a15@codeaurora.org>
Thanks Rajendra for pointing to the patch
On 16/11/16 15:50, Nayak, Rajendra wrote:
>>
>>
>> Rajendra,
>> Looks like qcom gdsc pm domain provider driver does not handle bus clks
>> along with power-domain, Is this something we should do? Or the bus
>> driver take care of it?
>
> I did post some patches to support handling of clocks associated with
> gdscs [1], but it got dropped at that point since there wasn't a
> real user, besides there were some open issues wrt the handling of
> !CONFIG_PM cases etc.
> I will revive and repost those patches again now based on the
> discussions last time around.
>
> [1]
> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-August/362492.html
This patch looks exactly like the one useful in pcie case, i would be
interesting to see the final patch on how we handle clocks which are
both related and not related to power domain.
thanks,
srini
>
^ permalink raw reply
* Re: [PATCH 3/4] PCI: dra7xx: Add support to force RC to work in GEN1 mode
From: Kishon Vijay Abraham I @ 2016-11-16 16:44 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: Bjorn Helgaas, Rob Herring, linux-omap-u79uwXL29TY76Z2rM5mHXA,
linux-pci-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, nsekhar-l0cyMroinI0,
Shawn Lin
In-Reply-To: <20161114212400.GA19092-1RhO1Y9PlrlHTL0Zs8A6p5iNqAH0jzoTYJqu5kTmcBRl57MIdRCFDg@public.gmane.org>
Hi Bjorn,
On Tuesday 15 November 2016 02:54 AM, Bjorn Helgaas wrote:
> [+cc Shawn]
>
> On Sat, Nov 12, 2016 at 12:40:10PM +0530, Kishon Vijay Abraham I wrote:
>> Hi,
>>
>> On Saturday 12 November 2016 02:45 AM, Bjorn Helgaas wrote:
>>> Hi Kishon,
>>>
>>> On Tue, Oct 11, 2016 at 06:28:34PM +0530, Kishon Vijay Abraham I wrote:
>>>> PCIe in AM57x/DRA7x devices is by default
>>>> configured to work in GEN2 mode. However there
>>>> may be situations when working in GEN1 mode is
>>>> desired. One example is limitation i925 (PCIe GEN2
>>>> mode not supported at junction temperatures < 0C).
>>>>
>>>> Add support to force Root Complex to work in GEN1
>>>> mode if so desired, but don't force GEN1 mode on
>>>> any board just yet.
>>>>
>>>> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
>>>> Signed-off-by: Sekhar Nori <nsekhar-l0cyMroinI0@public.gmane.org>
>>>> ---
>>>> Documentation/devicetree/bindings/pci/ti-pci.txt | 1 +
>>>> drivers/pci/host/pci-dra7xx.c | 27 ++++++++++++++++++++++
>>>> 2 files changed, 28 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
>>>> index 60e2516..a3d6ca3 100644
>>>> --- a/Documentation/devicetree/bindings/pci/ti-pci.txt
>>>> +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
>>>> @@ -25,6 +25,7 @@ PCIe Designware Controller
>>>>
>>>> Optional Property:
>>>> - gpios : Should be added if a gpio line is required to drive PERST# line
>>>> + - ti,pcie-is-gen1 : Force the PCIe controller to work in GEN1 (2.5 GT/s).
>>>
>>> Can we use "max-link-speed" so it's similar to imx6?
>>
>> yeah, maybe we should make it a generic PCI property?
>
> I forgot that Shawn has already done this! I had already merged those
> patches on pci/host-rockchip, but I moved them to pci/host since
> they're not Rockchip-specific. Can you take a look at that and see if
> you can do what you need based on that pci/host branch?
Sure, I'll look at that on Monday when I'm back from vacation.
Cheers
Kishon
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH net 1/3] net: phy: realtek: add eee advertisement disable options
From: Florian Fainelli @ 2016-11-16 17:01 UTC (permalink / raw)
To: Jerome Brunet, Andrew Lunn
Cc: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree-u79uwXL29TY76Z2rM5mHXA,
Carlo Caione, Kevin Hilman, Giuseppe Cavallaro, Alexandre TORGUE,
Martin Blumenstingl, Andre Roth, Neil Armstrong,
linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1479310731.17538.53.camel-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
On 11/16/2016 07:38 AM, Jerome Brunet wrote:
> On Wed, 2016-11-16 at 16:06 +0100, Andrew Lunn wrote:
>> On Wed, Nov 16, 2016 at 03:51:30PM +0100, Jerome Brunet wrote:
>>>
>>> On Wed, 2016-11-16 at 14:23 +0100, Andrew Lunn wrote:
>>>>
>>>>>
>>>>>
>>>>> There two kind of PHYs supporting eee, the one advertising eee
>>>>> by
>>>>> default (like realtek) and the one not advertising it (like
>>>>> micrel).
>>>
>>> This is just the default register value.
>>>
>>>>
>>>>
>>>> I don't know too much about EEE. So maybe a dumb question. Does
>>>> the
>>>> MAC need to be involved? Or is it just the PHY?
>>>>
>>>> If the MAC needs to be involved, the PHY should not be
>>>> advertising
>>>> EEE
>>>> unless the MAC asks for it by calling phy_init_eee(). If this is
>>>> true,
>>>> maybe we need to change the realtek driver, and others in that
>>>> class.
>>>
>>> As far I understand, the advertised capabilities are exchanged
>>> during
>>> the auto-negotiation.
>>>
>>> At this stage, if the advertisement is disabled (regarless of the
>>> actual support) on either side of the link, there will be no low
>>> power
>>> idle state on the Tx nor the Rx path.
>>>
>>> If the advertisement is enabled on both side but we don't call
>>> phy_init_eee, I suppose Tx won't enter LPI, but Rx could.
>>
>> What i was trying to find out is, if the MAC needs to support EEE as
>> well as the PHY, what happens when the MAC does not support EEE, but
>> the PHYs do negotiate EEE? Does it break?
>
> Interesting question. In a regular case, I suppose it should be fine.
> As you would have LPI only on the Rx path this should be transparent to
> the MAC. That's my understanding. Maybe people knowing EEE better than
> me could confirm (or not) ? Peppe? Alexandre?
EEE is a MAC and PHY feature, and both need to agree on what is enabled,
especially in the transmit path because the way packets may be
transmitted with or without EEE can be done differently at the HW level
(faster/slower return to idle, different clock source).
>
> I just checked with the OdroidC2, I disabled eee support by forcing
> "dma_cap.eee = 0" in stmmac_get_hw_features. As expected, no tx_LPI
> interrupts but plenty of rx_LPI interrupts.
>
> What was not expected is test failing like before.
> So in our case, having LPI on the Rx path is fine for receiving data,
> but not for sending.
OK, which really sounds like a potential interoperability problem, or
just the Realtek PHY with EEE enabled acting funky (irrespective of
being attached to stmmac).
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH 4/4] Update device tree Synopsys DW DMAC documentation
From: Eugeniy Paltsev @ 2016-11-16 17:01 UTC (permalink / raw)
To: andriy.shevchenko@linux.intel.com
Cc: vinod.koul@intel.com, linux-kernel@vger.kernel.org,
robh+dt@kernel.org, devicetree@vger.kernel.org,
Eugeniy.Paltsev@synopsys.com, linux-snps-arc@lists.infradead.org,
mark.rutland@arm.com, dmaengine@vger.kernel.org
In-Reply-To: <1479309042.24056.40.camel@linux.intel.com>
Hi Andy,
On Wed, 2016-11-16 at 17:10 +0200, Andy Shevchenko wrote:
> Overall, since we are going to expose some properties to the Device
> Tree
> I would really think twice about naming. Better if we reuse something
> existing already.
>
> So, what I can see is
>
> dmacap,private
> dmacap,memcpy
>
> Here is a selling point as well, i.e. standardization.
>
As I can see these property name used only in "mv_xor" driver. And
they are marked as deprecated.
So, I'm not sure if I should used these names.
I agree with other comments.
--
Paltsev Eugeniy
^ permalink raw reply
* Re: [PATCH net 1/3] net: phy: realtek: add eee advertisement disable options
From: Anand Moon @ 2016-11-16 17:06 UTC (permalink / raw)
To: Jerome Brunet
Cc: netdev-u79uwXL29TY76Z2rM5mHXA, devicetree, Florian Fainelli,
Alexandre TORGUE, Neil Armstrong, Martin Blumenstingl,
Kevin Hilman, Linux Kernel, Andre Roth,
linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Carlo Caione,
Giuseppe Cavallaro, linux-arm-kernel
In-Reply-To: <1479220154-25851-2-git-send-email-jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Hi Jerome.
On 15 November 2016 at 19:59, Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org> wrote:
> On some platforms, energy efficient ethernet with rtl8211 devices is
> causing issue, like throughput drop or broken link.
>
> This was reported on the OdroidC2 (DWMAC + RTL8211F). While the issue root
> cause is not fully understood yet, disabling EEE advertisement prevent auto
> negotiation from enabling EEE.
>
> This patch provides options to disable 1000T and 100TX EEE advertisement
> individually for the realtek phys supporting this feature.
>
> Reported-by: Martin Blumenstingl <martin.blumenstingl-gM/Ye1E23mwN+BqQ9rBEUg@public.gmane.org>
> Cc: Giuseppe Cavallaro <peppe.cavallaro-qxv4g6HH51o@public.gmane.org>
> Cc: Alexandre TORGUE <alexandre.torgue-qxv4g6HH51o@public.gmane.org>
> Signed-off-by: Jerome Brunet <jbrunet-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> Tested-by: Andre Roth <neolynx-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> ---
> drivers/net/phy/realtek.c | 65 ++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 64 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/realtek.c b/drivers/net/phy/realtek.c
> index aadd6e9f54ad..77235fd5faaf 100644
> --- a/drivers/net/phy/realtek.c
> +++ b/drivers/net/phy/realtek.c
> @@ -15,6 +15,12 @@
> */
> #include <linux/phy.h>
> #include <linux/module.h>
> +#include <linux/of.h>
> +
> +struct rtl8211x_phy_priv {
> + bool eee_1000t_disable;
> + bool eee_100tx_disable;
> +};
>
> #define RTL821x_PHYSR 0x11
> #define RTL821x_PHYSR_DUPLEX 0x2000
> @@ -93,12 +99,44 @@ static int rtl8211f_config_intr(struct phy_device *phydev)
> return err;
> }
>
> +static void rtl8211x_clear_eee_adv(struct phy_device *phydev)
> +{
> + struct rtl8211x_phy_priv *priv = phydev->priv;
> + u16 val;
> +
> + if (priv->eee_1000t_disable || priv->eee_100tx_disable) {
> + val = phy_read_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
> + MDIO_MMD_AN);
> +
> + if (priv->eee_1000t_disable)
> + val &= ~MDIO_AN_EEE_ADV_1000T;
> + if (priv->eee_100tx_disable)
> + val &= ~MDIO_AN_EEE_ADV_100TX;
> +
> + phy_write_mmd_indirect(phydev, MDIO_AN_EEE_ADV,
> + MDIO_MMD_AN, val);
> + }
> +}
> +
> +static int rtl8211x_config_init(struct phy_device *phydev)
> +{
> + int ret;
> +
> + ret = genphy_config_init(phydev);
> + if (ret < 0)
> + return ret;
> +
> + rtl8211x_clear_eee_adv(phydev);
> +
> + return 0;
> +}
> +
> static int rtl8211f_config_init(struct phy_device *phydev)
> {
> int ret;
> u16 reg;
>
> - ret = genphy_config_init(phydev);
> + ret = rtl8211x_config_init(phydev);
> if (ret < 0)
> return ret;
>
> @@ -115,6 +153,26 @@ static int rtl8211f_config_init(struct phy_device *phydev)
> return 0;
> }
>
> +static int rtl8211x_phy_probe(struct phy_device *phydev)
> +{
> + struct device *dev = &phydev->mdio.dev;
> + struct device_node *of_node = dev->of_node;
> + struct rtl8211x_phy_priv *priv;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->eee_1000t_disable =
> + of_property_read_bool(of_node, "realtek,disable-eee-1000t");
> + priv->eee_100tx_disable =
> + of_property_read_bool(of_node, "realtek,disable-eee-100tx");
> +
> + phydev->priv = priv;
> +
> + return 0;
> +}
> +
> static struct phy_driver realtek_drvs[] = {
> {
> .phy_id = 0x00008201,
> @@ -140,7 +198,9 @@ static struct phy_driver realtek_drvs[] = {
> .phy_id_mask = 0x001fffff,
> .features = PHY_GBIT_FEATURES,
> .flags = PHY_HAS_INTERRUPT,
> + .probe = &rtl8211x_phy_probe,
> .config_aneg = genphy_config_aneg,
> + .config_init = &rtl8211x_config_init,
> .read_status = genphy_read_status,
> .ack_interrupt = rtl821x_ack_interrupt,
> .config_intr = rtl8211e_config_intr,
> @@ -152,7 +212,9 @@ static struct phy_driver realtek_drvs[] = {
> .phy_id_mask = 0x001fffff,
> .features = PHY_GBIT_FEATURES,
> .flags = PHY_HAS_INTERRUPT,
> + .probe = &rtl8211x_phy_probe,
> .config_aneg = &genphy_config_aneg,
> + .config_init = &rtl8211x_config_init,
> .read_status = &genphy_read_status,
> .ack_interrupt = &rtl821x_ack_interrupt,
> .config_intr = &rtl8211e_config_intr,
> @@ -164,6 +226,7 @@ static struct phy_driver realtek_drvs[] = {
> .phy_id_mask = 0x001fffff,
> .features = PHY_GBIT_FEATURES,
> .flags = PHY_HAS_INTERRUPT,
> + .probe = &rtl8211x_phy_probe,
> .config_aneg = &genphy_config_aneg,
> .config_init = &rtl8211f_config_init,
> .read_status = &genphy_read_status,
> --
> 2.7.4
>
How about adding callback functionality for .soft_reset to handle BMCR
where we update the Auto-Negotiation for the phy,
as per the datasheet of the rtl8211f.
-Best Regard
Anand Moon
>
> _______________________________________________
> linux-amlogic mailing list
> linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-amlogic
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v4 4/4] ARM: dts: da850: Add the usb otg device nodeg
From: Bin Liu @ 2016-11-16 17:24 UTC (permalink / raw)
To: Sekhar Nori
Cc: Alexandre Bailon, khilman-rdvid1DuHRBWk0Htik3J/w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
In-Reply-To: <9a73c416-fe4c-57c3-af53-87146dae2206-l0cyMroinI0@public.gmane.org>
On Wed, Nov 16, 2016 at 12:06:51PM +0530, Sekhar Nori wrote:
> On Wednesday 16 November 2016 02:49 AM, Bin Liu wrote:
> > On Tue, Nov 15, 2016 at 04:16:02PM +0530, Sekhar Nori wrote:
> >> On Thursday 03 November 2016 09:29 PM, Alexandre Bailon wrote:
> >>> This adds the device tree node for the usb otg
> >>> controller present in the da850 family of SoC's.
> >>> This also enables the otg usb controller for the lcdk board.
> >>>
> >>> Signed-off-by: Alexandre Bailon <abailon-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
> >>> ---
> >>> arch/arm/boot/dts/da850-lcdk.dts | 8 ++++++++
> >>> arch/arm/boot/dts/da850.dtsi | 15 +++++++++++++++
> >>> 2 files changed, 23 insertions(+)
> >>>
> >>> diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts
> >>> index 7b8ab21..9f5040c 100644
> >>> --- a/arch/arm/boot/dts/da850-lcdk.dts
> >>> +++ b/arch/arm/boot/dts/da850-lcdk.dts
> >>> @@ -158,6 +158,14 @@
> >>> rx-num-evt = <32>;
> >>> };
> >>>
> >>> +&usb_phy {
> >>> + status = "okay";
> >>> + };
> >>
> >> As mentioned by David already, this node needs to be removed. Please
> >> rebase this on top of latest linux-davinci/master when ready for merging
> >> (driver changes accepted).
> >
> > Dropped this patch due to this comment.
>
> Bin, Please do not apply dts or arch/arm/mach-davinci patches. I have a
> bunch queued through my tree and more in pipeline and it will cause
> unnecessary merge conflicts in linux-next or at Linus.
Sure, I will drop this whole set, and only apply the musb patches in the
new v5.
>
> For future, I have asked Alexandre to send driver and dts patches as
> separate series so there is no confusion on who should apply.
I will keep in mind to ping other domain maintainers before applying
non-musb patches in future.
>
> Thanks,
> Sekhar
Regards,
-Bin.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox