* [PATCH 15/16] drivers/fsi: Add documentation for GPIO bindings
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Chris Bostic, joel, jk, linux-kernel, andrew, alistair, benh
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Chris Bostic <cbostic@us.ibm.com>
Add fsi master gpio device tree binding documentation
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
.../devicetree/bindings/fsi/fsi-master-gpio.txt | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
diff --git a/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
new file mode 100644
index 0000000..ff3a62e
--- /dev/null
+++ b/Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
@@ -0,0 +1,21 @@
+Device-tree bindings for gpio-based FSI master driver
+-----------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,fsi-master-gpio";
+ - clk-gpios;
+ - data-gpios;
+
+Optional properties:
+ - enable-gpios;
+ - trans-gpios;
+ - mux-gpios;
+
+fsi-master {
+ compatible = "ibm,fsi-master", "ibm,fsi-master-gpio";
+ clk-gpios = <&gpio 0 &gpio 6>;
+ data-gpios = <&gpio 1 &gpio 7>;
+ enable-gpios = <&gpio 2 &gpio 8>; /* Enable FSI data in/out */
+ trans-gpios = <&gpio 3 &gpio 9>; /* Volts translator direction */
+ mux-gpios = <&gpio 4> &gpio 10>; /* Multiplexer for FSI pins */
+}
--
1.8.2.2
^ permalink raw reply related
* [PATCH 14/16] drivers/fsi: Add master unscan
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Chris Bostic, joel, jk, linux-kernel, andrew, alistair, benh
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Chris Bostic <cbostic@us.ibm.com>
Allow a master to undo a previous scan. Should a master scan a bus
twice it will need to ensure it doesn't double register any
previously detected device.
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/fsi-core.c | 36 +++++++++++++++++++++++++++++++++++-
drivers/fsi/fsi-master.h | 2 ++
include/linux/fsi.h | 1 +
3 files changed, 38 insertions(+), 1 deletion(-)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index a28434b..8ccfe50 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -41,6 +41,8 @@
static atomic_t master_idx = ATOMIC_INIT(-1);
struct fsi_slave {
+ struct list_head list_link; /* Master's list of slaves */
+ struct list_head my_engines;
struct device dev;
struct fsi_master *master;
int link;
@@ -196,6 +198,8 @@ static int fsi_slave_scan(struct fsi_slave *slave)
uint32_t conf;
int rc, i;
+ INIT_LIST_HEAD(&slave->my_engines);
+
/*
* scan engines
*
@@ -264,7 +268,9 @@ static int fsi_slave_scan(struct fsi_slave *slave)
if (rc) {
dev_warn(&slave->dev, "add failed: %d\n", rc);
put_device(&dev->dev);
+ continue;
}
+ list_add(&dev->link, &slave->my_engines);
}
engine_addr += slots * engine_page_size;
@@ -357,7 +363,7 @@ static int fsi_slave_init(struct fsi_master *master,
put_device(&slave->dev);
return rc;
}
-
+ list_add(&slave->list_link, &master->my_slaves);
fsi_slave_scan(slave);
return 0;
}
@@ -388,6 +394,11 @@ static int fsi_master_scan(struct fsi_master *master)
int link, slave_id, rc;
uint32_t smode;
+ if (!master->slave_list) {
+ INIT_LIST_HEAD(&master->my_slaves);
+ master->slave_list = true;
+ }
+
for (link = 0; link < master->n_links; link++) {
rc = fsi_master_link_enable(master, link);
if (rc) {
@@ -423,9 +434,31 @@ static int fsi_master_scan(struct fsi_master *master)
return 0;
}
+static void fsi_master_unscan(struct fsi_master *master)
+{
+ struct fsi_slave *slave, *slave_tmp;
+ struct fsi_device *fsi_dev, *fsi_dev_tmp;
+
+ if (!master->slave_list)
+ return;
+
+ list_for_each_entry_safe(slave, slave_tmp, &master->my_slaves,
+ list_link) {
+ list_del(&slave->list_link);
+ list_for_each_entry_safe(fsi_dev, fsi_dev_tmp,
+ &slave->my_engines, link) {
+ list_del(&fsi_dev->link);
+ put_device(&fsi_dev->dev);
+ }
+ device_unregister(&slave->dev);
+ }
+ master->slave_list = false;
+}
+
int fsi_master_register(struct fsi_master *master)
{
master->idx = atomic_inc_return(&master_idx);
+ master->slave_list = false;
get_device(master->dev);
fsi_master_scan(master);
return 0;
@@ -434,6 +467,7 @@ int fsi_master_register(struct fsi_master *master)
void fsi_master_unregister(struct fsi_master *master)
{
+ fsi_master_unscan(master);
put_device(master->dev);
}
EXPORT_SYMBOL_GPL(fsi_master_unregister);
diff --git a/drivers/fsi/fsi-master.h b/drivers/fsi/fsi-master.h
index 56aad0e..454af2b 100644
--- a/drivers/fsi/fsi-master.h
+++ b/drivers/fsi/fsi-master.h
@@ -20,6 +20,8 @@
#include <linux/device.h>
struct fsi_master {
+ struct list_head my_slaves;
+ bool slave_list;
struct device *dev;
int idx;
int n_links;
diff --git a/include/linux/fsi.h b/include/linux/fsi.h
index 66bce48..924502b 100644
--- a/include/linux/fsi.h
+++ b/include/linux/fsi.h
@@ -18,6 +18,7 @@
#include <linux/device.h>
struct fsi_device {
+ struct list_head link; /* for slave's list */
struct device dev;
u8 engine_type;
u8 version;
--
1.8.2.2
^ permalink raw reply related
* [PATCH 13/16] drivers/fsi: Set slave SMODE to init communication
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Chris Bostic, joel, jk, linux-kernel, andrew, alistair, benh
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Chris Bostic <cbostic@us.ibm.com>
Set CFAM to appropriate ID so that the controlling master
can manage link memory ranges. Add slave engine register
definitions.
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/fsi-core.c | 90 +++++++++++++++++++++++++++++++++++++++++++++++++-
1 file changed, 89 insertions(+), 1 deletion(-)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index 93de0f1..a28434b 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -34,6 +34,7 @@
#define FSI_SLAVE_CONF_DATA_BITS 28
#define FSI_PEEK_BASE 0x410
+#define FSI_SLAVE_BASE 0x800
static const int engine_page_size = 0x400;
@@ -53,8 +54,26 @@ static int fsi_slave_read(struct fsi_slave *slave, uint32_t addr,
static int fsi_slave_write(struct fsi_slave *slave, uint32_t addr,
const void *val, size_t size);
-/* FSI endpoint-device support */
+/*
+ * FSI slave engine control register offsets
+ */
+#define FSI_SMODE 0x0 /* R/W: Mode register */
+
+/*
+ * SMODE fields
+ */
+#define FSI_SMODE_WSC 0x80000000 /* Warm start done */
+#define FSI_SMODE_ECRC 0x20000000 /* Hw CRC check */
+#define FSI_SMODE_SID_SHIFT 24 /* ID shift */
+#define FSI_SMODE_SID_MASK 3 /* ID Mask */
+#define FSI_SMODE_ED_SHIFT 20 /* Echo delay shift */
+#define FSI_SMODE_ED_MASK 0xf /* Echo delay mask */
+#define FSI_SMODE_SD_SHIFT 16 /* Send delay shift */
+#define FSI_SMODE_SD_MASK 0xf /* Send delay mask */
+#define FSI_SMODE_LBCRR_SHIFT 8 /* Clk ratio shift */
+#define FSI_SMODE_LBCRR_MASK 0xf /* Clk ratio mask */
+/* FSI endpoint-device support */
int fsi_device_read(struct fsi_device *dev, uint32_t addr, void *val,
size_t size)
{
@@ -133,6 +152,30 @@ uint8_t fsi_crc4(uint8_t c, uint64_t x, int bits)
/* FSI slave support */
+/* Encode slave local bus echo delay */
+static inline uint32_t fsi_smode_echodly(int x)
+{
+ return (x & FSI_SMODE_ED_MASK) << FSI_SMODE_ED_SHIFT;
+}
+
+/* Encode slave local bus send delay */
+static inline uint32_t fsi_smode_senddly(int x)
+{
+ return (x & FSI_SMODE_SD_MASK) << FSI_SMODE_SD_SHIFT;
+}
+
+/* Encode slave local bus clock rate ratio */
+static inline uint32_t fsi_smode_lbcrr(int x)
+{
+ return (x & FSI_SMODE_LBCRR_MASK) << FSI_SMODE_LBCRR_SHIFT;
+}
+
+/* Encode slave ID */
+static inline uint32_t fsi_smode_sid(int x)
+{
+ return (x & FSI_SMODE_SID_MASK) << FSI_SMODE_SID_SHIFT;
+}
+
static int fsi_slave_read(struct fsi_slave *slave, uint32_t addr,
void *val, size_t size)
{
@@ -240,6 +283,22 @@ static void fsi_slave_release(struct device *dev)
kfree(slave);
}
+static uint32_t set_smode_defaults(struct fsi_master *master)
+{
+ return FSI_SMODE_WSC | FSI_SMODE_ECRC
+ | fsi_smode_echodly(0xf) | fsi_smode_senddly(0xf)
+ | fsi_smode_lbcrr(1);
+}
+
+static int fsi_slave_set_smode(struct fsi_master *master, int link, int id)
+{
+ uint32_t smode = set_smode_defaults(master);
+
+ smode |= fsi_smode_sid(id);
+ return master->write(master, link, 3, FSI_SLAVE_BASE + FSI_SMODE,
+ &smode, sizeof(smode));
+}
+
static int fsi_slave_init(struct fsi_master *master,
int link, uint8_t slave_id)
{
@@ -248,6 +307,21 @@ static int fsi_slave_init(struct fsi_master *master,
int rc;
uint8_t crc;
+ /*
+ * todo: Due to CFAM hardware issues related to BREAK commands we're
+ * limited to only one CFAM per link. Once issues are resolved this
+ * restriction can be removed.
+ */
+ if (slave_id > 0)
+ return 0;
+
+ rc = fsi_slave_set_smode(master, link, slave_id);
+ if (rc) {
+ dev_warn(master->dev, "can't set smode on slave:%02x:%02x %d\n",
+ link, slave_id, rc);
+ return -ENODEV;
+ }
+
rc = master->read(master, link, slave_id, 0, &chip_id, sizeof(chip_id));
if (rc) {
dev_warn(master->dev, "can't read slave %02x:%02x: %d\n",
@@ -312,6 +386,7 @@ static int fsi_master_break(struct fsi_master *master, int link)
static int fsi_master_scan(struct fsi_master *master)
{
int link, slave_id, rc;
+ uint32_t smode;
for (link = 0; link < master->n_links; link++) {
rc = fsi_master_link_enable(master, link);
@@ -327,6 +402,19 @@ static int fsi_master_scan(struct fsi_master *master)
continue;
}
+ /*
+ * Verify can read slave at default ID location. If fails
+ * there must be nothing on other end of link
+ */
+ rc = master->read(master, link, 3, FSI_SLAVE_BASE + FSI_SMODE,
+ &smode, sizeof(smode));
+ if (rc) {
+ dev_dbg(master->dev,
+ "Read link:%d smode default id failed:%d\n",
+ link, rc);
+ continue;
+ }
+
for (slave_id = 0; slave_id < FSI_N_SLAVES; slave_id++)
fsi_slave_init(master, link, slave_id);
--
1.8.2.2
^ permalink raw reply related
* [PATCH 10/16] drivers/fsi: scan slaves & register devices
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
sre-DgEjT+Ai2ygdnm+yROfE0A, mturquette-rdvid1DuHRBWk0Htik3J/w,
geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: Jeremy Kerr, joel-U3u1mxZcP9KHXe+LvDLADg,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, andrew-zrmu5oMJ5Fs,
alistair-Y4h6yKqj69EXC2x5gXVKYQ,
benh-XVmvHMARGAS8U2dJNN8I7kB+6BGkLq7r, Chris Bostic
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
From: Jeremy Kerr <jk-mnsaURCQ41sdnm+yROfE0A@public.gmane.org>
Now that we have fsi_slave devices, scan each for endpoints, and
register them on the fsi bus.
Includes contributions from Chris Bostic <cbostic-r/Jw6+rmf7HQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Jeremy Kerr <jk-mnsaURCQ41sdnm+yROfE0A@public.gmane.org>
Signed-off-by: Chris Bostic <cbostic-r/Jw6+rmf7HQT0dZR+AlfA@public.gmane.org>
---
drivers/fsi/fsi-core.c | 136 +++++++++++++++++++++++++++++++++++++++++++++++--
include/linux/fsi.h | 4 ++
2 files changed, 136 insertions(+), 4 deletions(-)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index aa4330a..b51ea35 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -21,9 +21,19 @@
#include "fsi-master.h"
#define FSI_N_SLAVES 4
-#define FSI_SLAVE_CONF_CRC_SHIFT 4
-#define FSI_SLAVE_CONF_CRC_MASK 0x0000000f
-#define FSI_SLAVE_CONF_DATA_BITS 28
+
+#define FSI_SLAVE_CONF_NEXT_MASK 0x80000000
+#define FSI_SLAVE_CONF_SLOTS_MASK 0x00ff0000
+#define FSI_SLAVE_CONF_SLOTS_SHIFT 16
+#define FSI_SLAVE_CONF_VERSION_MASK 0x0000f000
+#define FSI_SLAVE_CONF_VERSION_SHIFT 12
+#define FSI_SLAVE_CONF_TYPE_MASK 0x00000ff0
+#define FSI_SLAVE_CONF_TYPE_SHIFT 4
+#define FSI_SLAVE_CONF_CRC_SHIFT 4
+#define FSI_SLAVE_CONF_CRC_MASK 0x0000000f
+#define FSI_SLAVE_CONF_DATA_BITS 28
+
+static const int engine_page_size = 0x400;
static atomic_t master_idx = ATOMIC_INIT(-1);
@@ -36,6 +46,30 @@ struct fsi_slave {
#define to_fsi_slave(d) container_of(d, struct fsi_slave, dev)
+/* FSI endpoint-device support */
+
+static void fsi_device_release(struct device *_device)
+{
+ struct fsi_device *device = to_fsi_dev(_device);
+
+ kfree(device);
+}
+
+static struct fsi_device *fsi_create_device(struct fsi_slave *slave)
+{
+ struct fsi_device *dev;
+
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (!dev)
+ return NULL;
+
+ dev->dev.parent = &slave->dev;
+ dev->dev.bus = &fsi_bus_type;
+ dev->dev.release = fsi_device_release;
+
+ return dev;
+}
+
/* crc helpers */
static const uint8_t crc4_tab[] = {
0x0, 0x7, 0xe, 0x9, 0xb, 0xc, 0x5, 0x2,
@@ -59,6 +93,99 @@ uint8_t fsi_crc4(uint8_t c, uint64_t x, int bits)
/* FSI slave support */
+static int fsi_slave_read(struct fsi_slave *slave, uint32_t addr,
+ void *val, size_t size)
+{
+ return slave->master->read(slave->master, slave->link,
+ slave->id, addr, val, size);
+}
+
+static int fsi_slave_scan(struct fsi_slave *slave)
+{
+ uint32_t engine_addr;
+ uint32_t conf;
+ int rc, i;
+
+ /*
+ * scan engines
+ *
+ * We keep the peek mode and slave engines for the core; so start
+ * at the third slot in the configuration table. We also need to
+ * skip the chip ID entry at the start of the address space.
+ */
+ engine_addr = engine_page_size * 3;
+ for (i = 2; i < engine_page_size / sizeof(uint32_t); i++) {
+ uint8_t slots, version, type, crc;
+ struct fsi_device *dev;
+
+ rc = fsi_slave_read(slave, (i + 1) * sizeof(conf),
+ &conf, sizeof(conf));
+ if (rc) {
+ dev_warn(&slave->dev,
+ "error reading slave registers\n");
+ return -1;
+ }
+
+ crc = fsi_crc4(0, conf >> FSI_SLAVE_CONF_CRC_SHIFT,
+ FSI_SLAVE_CONF_DATA_BITS);
+ if (crc != (conf & FSI_SLAVE_CONF_CRC_MASK)) {
+ dev_warn(&slave->dev,
+ "crc error in slave register at 0x%04x\n",
+ i);
+ return -1;
+ }
+
+ slots = (conf & FSI_SLAVE_CONF_SLOTS_MASK)
+ >> FSI_SLAVE_CONF_SLOTS_SHIFT;
+ version = (conf & FSI_SLAVE_CONF_VERSION_MASK)
+ >> FSI_SLAVE_CONF_VERSION_SHIFT;
+ type = (conf & FSI_SLAVE_CONF_TYPE_MASK)
+ >> FSI_SLAVE_CONF_TYPE_SHIFT;
+
+ /*
+ * Unused address areas are marked by a zero type value; this
+ * skips the defined address areas
+ */
+ if (type != 0) {
+
+ /* create device */
+ dev = fsi_create_device(slave);
+ if (!dev)
+ return -ENOMEM;
+
+ dev->slave = slave;
+ dev->engine_type = type;
+ dev->version = version;
+ dev->unit = i;
+ dev->addr = engine_addr;
+ dev->size = slots * engine_page_size;
+
+ dev_info(&slave->dev,
+ "engine[%i]: type %x, version %x, addr %x size %x\n",
+ dev->unit, dev->engine_type, version,
+ dev->addr, dev->size);
+
+ device_initialize(&dev->dev);
+ dev_set_name(&dev->dev, "%02x:%02x:%02x:%02x",
+ slave->master->idx, slave->link,
+ slave->id, i - 2);
+
+ rc = device_add(&dev->dev);
+ if (rc) {
+ dev_warn(&slave->dev, "add failed: %d\n", rc);
+ put_device(&dev->dev);
+ }
+ }
+
+ engine_addr += slots * engine_page_size;
+
+ if (!(conf & FSI_SLAVE_CONF_NEXT_MASK))
+ break;
+ }
+
+ return 0;
+}
+
static void fsi_slave_release(struct device *dev)
{
struct fsi_slave *slave = to_fsi_slave(dev);
@@ -110,7 +237,8 @@ static int fsi_slave_init(struct fsi_master *master,
return rc;
}
- return rc;
+ fsi_slave_scan(slave);
+ return 0;
}
/* FSI master support */
diff --git a/include/linux/fsi.h b/include/linux/fsi.h
index 273cbf6..efa55ba 100644
--- a/include/linux/fsi.h
+++ b/include/linux/fsi.h
@@ -21,6 +21,10 @@ struct fsi_device {
struct device dev;
u8 engine_type;
u8 version;
+ u8 unit;
+ struct fsi_slave *slave;
+ uint32_t addr;
+ uint32_t size;
};
struct fsi_device_id {
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 07/16] drivers/fsi: Add empty master scan
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Jeremy Kerr, joel, linux-kernel, andrew, alistair, benh,
Chris Bostic
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Jeremy Kerr <jk@ozlabs.org>
When a new fsi master is added, we will need to scan its links, and
slaves attached to those links. This change introduces a little shell to
iterate the links, which we will populate with the actual slave scan in
a later change.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/fsi-core.c | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index 60a6d91..ceaf536 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -19,6 +19,8 @@
#include "fsi-master.h"
+#define FSI_N_SLAVES 4
+
static atomic_t master_idx = ATOMIC_INIT(-1);
struct fsi_slave {
@@ -30,12 +32,34 @@ struct fsi_slave {
#define to_fsi_slave(d) container_of(d, struct fsi_slave, dev)
+/* FSI slave support */
+static int fsi_slave_init(struct fsi_master *master,
+ int link, uint8_t slave_id)
+{
+ /* todo: initialise slave device, perform engine scan */
+
+ return -ENODEV;
+}
+
/* FSI master support */
+static int fsi_master_scan(struct fsi_master *master)
+{
+ int link, slave_id;
+
+ for (link = 0; link < master->n_links; link++)
+ for (slave_id = 0; slave_id < FSI_N_SLAVES; slave_id++)
+ fsi_slave_init(master, link, slave_id);
+
+ return 0;
+
+}
+
int fsi_master_register(struct fsi_master *master)
{
master->idx = atomic_inc_return(&master_idx);
get_device(master->dev);
+ fsi_master_scan(master);
return 0;
}
EXPORT_SYMBOL_GPL(fsi_master_register);
--
1.8.2.2
^ permalink raw reply related
* [PATCH 06/16] drivers/fsi: Add slave definition
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Jeremy Kerr, joel, linux-kernel, andrew, alistair, benh,
Chris Bostic
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Jeremy Kerr <jk@ozlabs.org>
Add the initial fsi slave device, which is private to the core code.
This will be a child of the master, and parent to endpoint devices.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/fsi-core.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index ce9428d..60a6d91 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -21,6 +21,15 @@
static atomic_t master_idx = ATOMIC_INIT(-1);
+struct fsi_slave {
+ struct device dev;
+ struct fsi_master *master;
+ int link;
+ uint8_t id;
+};
+
+#define to_fsi_slave(d) container_of(d, struct fsi_slave, dev)
+
/* FSI master support */
int fsi_master_register(struct fsi_master *master)
--
1.8.2.2
^ permalink raw reply related
* [PATCH 05/16] drivers/fsi: Add fake master driver
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: Jeremy Kerr, joel, linux-kernel, andrew, alistair, benh,
Chris Bostic
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Jeremy Kerr <jk@ozlabs.org>
For debugging, add a fake master driver, that only supports reads,
returning a fixed set of data.
Includes changes from Chris Bostic <cbostic@us.ibm.com>.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/Kconfig | 10 +++++
drivers/fsi/Makefile | 1 +
drivers/fsi/fsi-master-fake.c | 95 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 106 insertions(+)
create mode 100644 drivers/fsi/fsi-master-fake.c
diff --git a/drivers/fsi/Kconfig b/drivers/fsi/Kconfig
index 04c1a0e..f065dbe 100644
--- a/drivers/fsi/Kconfig
+++ b/drivers/fsi/Kconfig
@@ -9,4 +9,14 @@ config FSI
---help---
FSI - the FRU Support Interface - is a simple bus for low-level
access to POWER-based hardware.
+
+if FSI
+
+config FSI_MASTER_FAKE
+ tristate "Fake FSI master"
+ depends on FSI
+ ---help---
+ This option enables a fake FSI master driver for debugging.
+endif
+
endmenu
diff --git a/drivers/fsi/Makefile b/drivers/fsi/Makefile
index db0e5e7..847c00c 100644
--- a/drivers/fsi/Makefile
+++ b/drivers/fsi/Makefile
@@ -1,2 +1,3 @@
obj-$(CONFIG_FSI) += fsi-core.o
+obj-$(CONFIG_FSI_MASTER_FAKE) += fsi-master-fake.o
diff --git a/drivers/fsi/fsi-master-fake.c b/drivers/fsi/fsi-master-fake.c
new file mode 100644
index 0000000..b42fe5b
--- /dev/null
+++ b/drivers/fsi/fsi-master-fake.c
@@ -0,0 +1,95 @@
+/*
+ * Fake FSI master driver for FSI development
+ *
+ * Copyright (C) IBM Corporation 2016
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+
+#include "fsi-master.h"
+
+static const uint8_t data[] = {
+ 0xc0, 0x02, 0x08, 0x03, /* chip id */
+ 0x80, 0x01, 0x11, 0x00, /* peek */
+ 0x80, 0x01, 0x20, 0x3e, /* slave */
+ 0x00, 0x01, 0x10, 0xa5, /* i2c */
+};
+
+
+static int fsi_master_fake_read(struct fsi_master *_master, int link,
+ uint8_t slave, uint32_t addr, void *val, size_t size)
+{
+ if (link != 0)
+ return -ENODEV;
+
+ if (addr + size > sizeof(data))
+ memset(val, 0, size);
+ else
+ memcpy(val, data + addr, size);
+
+ return 0;
+}
+
+static int fsi_master_fake_write(struct fsi_master *_master, int link,
+ uint8_t slave, uint32_t addr, const void *val, size_t size)
+{
+ if (link != 0)
+ return -ENODEV;
+
+ return -EACCES;
+}
+
+static int fsi_master_fake_probe(struct platform_device *pdev)
+{
+ struct fsi_master *master;
+
+ master = devm_kzalloc(&pdev->dev, sizeof(*master), GFP_KERNEL);
+ if (!master)
+ return -ENOMEM;
+
+ master->dev = &pdev->dev;
+ master->n_links = 1;
+ master->read = fsi_master_fake_read;
+ master->write = fsi_master_fake_write;
+
+ return fsi_master_register(master);
+}
+
+static const struct of_device_id fsi_master_fake_match[] = {
+ { .compatible = "ibm,fsi-master-fake" },
+ { },
+};
+
+static struct platform_driver fsi_master_fake_driver = {
+ .driver = {
+ .name = "fsi-master-fake",
+ .of_match_table = fsi_master_fake_match,
+ },
+ .probe = fsi_master_fake_probe,
+};
+
+static int __init fsi_master_fake_init(void)
+{
+ struct device_node *np;
+
+ platform_driver_register(&fsi_master_fake_driver);
+
+ for_each_compatible_node(np, NULL, "ibm,fsi-master-fake")
+ of_platform_device_create(np, NULL, NULL);
+
+ return 0;
+}
+
+module_init(fsi_master_fake_init);
--
1.8.2.2
^ permalink raw reply related
* [PATCH 03/16] drivers/fsi: add driver to device matches
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: andrew, alistair, linux-kernel, Chris Bostic, Jeremy Kerr, benh,
joel
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Jeremy Kerr <jk@ozlabs.org>
Driver bind to devices based on the engine types & (optional) versions.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/fsi/fsi-core.c | 21 +++++++++++++++++++++
include/linux/fsi.h | 21 +++++++++++++++++++--
2 files changed, 40 insertions(+), 2 deletions(-)
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
index 3e45306..3d55bd5 100644
--- a/drivers/fsi/fsi-core.c
+++ b/drivers/fsi/fsi-core.c
@@ -19,8 +19,29 @@
/* FSI core & Linux bus type definitions */
+static int fsi_bus_match(struct device *dev, struct device_driver *drv)
+{
+ struct fsi_device *fsi_dev = to_fsi_dev(dev);
+ struct fsi_driver *fsi_drv = to_fsi_drv(drv);
+ const struct fsi_device_id *id;
+
+ if (!fsi_drv->id_table)
+ return 0;
+
+ for (id = fsi_drv->id_table; id->engine_type; id++) {
+ if (id->engine_type != fsi_dev->engine_type)
+ continue;
+ if (id->version == FSI_VERSION_ANY ||
+ id->version == fsi_dev->version)
+ return 1;
+ }
+
+ return 0;
+}
+
struct bus_type fsi_bus_type = {
.name = "fsi",
+ .match = fsi_bus_match,
};
EXPORT_SYMBOL_GPL(fsi_bus_type);
diff --git a/include/linux/fsi.h b/include/linux/fsi.h
index f73886a..273cbf6 100644
--- a/include/linux/fsi.h
+++ b/include/linux/fsi.h
@@ -18,11 +18,28 @@
#include <linux/device.h>
struct fsi_device {
- struct device dev;
+ struct device dev;
+ u8 engine_type;
+ u8 version;
};
+struct fsi_device_id {
+ u8 engine_type;
+ u8 version;
+};
+
+#define FSI_VERSION_ANY 0
+
+#define FSI_DEVICE(t) \
+ .engine_type = (t), .version = FSI_VERSION_ANY,
+
+#define FSI_DEVICE_VERSIONED(t, v) \
+ .engine_type = (t), .version = (v),
+
+
struct fsi_driver {
- struct device_driver drv;
+ struct device_driver drv;
+ const struct fsi_device_id *id_table;
};
#define to_fsi_dev(devp) container_of(devp, struct fsi_device, dev)
--
1.8.2.2
^ permalink raw reply related
* [PATCH 02/16] drivers/fsi: Add device & driver definitions
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
sre-DgEjT+Ai2ygdnm+yROfE0A, mturquette-rdvid1DuHRBWk0Htik3J/w,
geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: Jeremy Kerr, joel-U3u1mxZcP9KHXe+LvDLADg,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, andrew-zrmu5oMJ5Fs,
alistair-Y4h6yKqj69EXC2x5gXVKYQ,
benh-XVmvHMARGAS8U2dJNN8I7kB+6BGkLq7r, Chris Bostic
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
From: Jeremy Kerr <jk-mnsaURCQ41sdnm+yROfE0A@public.gmane.org>
Add structs for fsi devices & drivers, and struct device conversion
functions.
Signed-off-by: Jeremy Kerr <jk-mnsaURCQ41sdnm+yROfE0A@public.gmane.org>
Signed-off-by: Chris Bostic <cbostic-r/Jw6+rmf7HQT0dZR+AlfA@public.gmane.org>
---
include/linux/fsi.h | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/include/linux/fsi.h b/include/linux/fsi.h
index 47aa181..f73886a 100644
--- a/include/linux/fsi.h
+++ b/include/linux/fsi.h
@@ -17,6 +17,17 @@
#include <linux/device.h>
+struct fsi_device {
+ struct device dev;
+};
+
+struct fsi_driver {
+ struct device_driver drv;
+};
+
+#define to_fsi_dev(devp) container_of(devp, struct fsi_device, dev)
+#define to_fsi_drv(drvp) container_of(drvp, struct fsi_driver, drv)
+
extern struct bus_type fsi_bus_type;
#endif /* LINUX_FSI_H */
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 01/16] drivers/fsi: Add empty fsi bus definitions
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt, mark.rutland, linux, gregkh, sre, mturquette,
geert+renesas, devicetree, linux-arm-kernel
Cc: andrew, alistair, linux-kernel, Chris Bostic, Jeremy Kerr, benh,
joel
In-Reply-To: <1481069677-53660-1-git-send-email-christopher.lee.bostic@gmail.com>
From: Jeremy Kerr <jk@ozlabs.org>
This change adds the initial (empty) fsi bus definition, and introduces
drivers/fsi/.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Chris Bostic <cbostic@us.ibm.com>
---
drivers/Kconfig | 2 ++
drivers/Makefile | 1 +
drivers/fsi/Kconfig | 12 ++++++++++++
drivers/fsi/Makefile | 2 ++
drivers/fsi/fsi-core.c | 38 ++++++++++++++++++++++++++++++++++++++
include/linux/fsi.h | 22 ++++++++++++++++++++++
6 files changed, 77 insertions(+)
create mode 100644 drivers/fsi/Kconfig
create mode 100644 drivers/fsi/Makefile
create mode 100644 drivers/fsi/fsi-core.c
create mode 100644 include/linux/fsi.h
diff --git a/drivers/Kconfig b/drivers/Kconfig
index e1e2066..117ca14c 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -202,4 +202,6 @@ source "drivers/hwtracing/intel_th/Kconfig"
source "drivers/fpga/Kconfig"
+source "drivers/fsi/Kconfig"
+
endmenu
diff --git a/drivers/Makefile b/drivers/Makefile
index f0afdfb..126e109 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -173,3 +173,4 @@ obj-$(CONFIG_STM) += hwtracing/stm/
obj-$(CONFIG_ANDROID) += android/
obj-$(CONFIG_NVMEM) += nvmem/
obj-$(CONFIG_FPGA) += fpga/
+obj-$(CONFIG_FSI) += fsi/
diff --git a/drivers/fsi/Kconfig b/drivers/fsi/Kconfig
new file mode 100644
index 0000000..04c1a0e
--- /dev/null
+++ b/drivers/fsi/Kconfig
@@ -0,0 +1,12 @@
+#
+# FSI subsystem
+#
+
+menu "FSI support"
+
+config FSI
+ tristate "FSI support"
+ ---help---
+ FSI - the FRU Support Interface - is a simple bus for low-level
+ access to POWER-based hardware.
+endmenu
diff --git a/drivers/fsi/Makefile b/drivers/fsi/Makefile
new file mode 100644
index 0000000..db0e5e7
--- /dev/null
+++ b/drivers/fsi/Makefile
@@ -0,0 +1,2 @@
+
+obj-$(CONFIG_FSI) += fsi-core.o
diff --git a/drivers/fsi/fsi-core.c b/drivers/fsi/fsi-core.c
new file mode 100644
index 0000000..3e45306
--- /dev/null
+++ b/drivers/fsi/fsi-core.c
@@ -0,0 +1,38 @@
+/*
+ * FSI core driver
+ *
+ * Copyright (C) IBM Corporation 2016
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/fsi.h>
+#include <linux/module.h>
+
+/* FSI core & Linux bus type definitions */
+
+struct bus_type fsi_bus_type = {
+ .name = "fsi",
+};
+EXPORT_SYMBOL_GPL(fsi_bus_type);
+
+static int fsi_init(void)
+{
+ return bus_register(&fsi_bus_type);
+}
+
+static void fsi_exit(void)
+{
+ bus_unregister(&fsi_bus_type);
+}
+
+module_init(fsi_init);
+module_exit(fsi_exit);
diff --git a/include/linux/fsi.h b/include/linux/fsi.h
new file mode 100644
index 0000000..47aa181
--- /dev/null
+++ b/include/linux/fsi.h
@@ -0,0 +1,22 @@
+/* FSI device & driver interfaces
+ *
+ * Copyright (C) IBM Corporation 2016
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef LINUX_FSI_H
+#define LINUX_FSI_H
+
+#include <linux/device.h>
+
+extern struct bus_type fsi_bus_type;
+
+#endif /* LINUX_FSI_H */
--
1.8.2.2
^ permalink raw reply related
* [PATCH 00/16] FSI device driver introduction
From: Chris Bostic @ 2016-12-07 0:14 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
sre-DgEjT+Ai2ygdnm+yROfE0A, mturquette-rdvid1DuHRBWk0Htik3J/w,
geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
Cc: Chris Bostic, joel-U3u1mxZcP9KHXe+LvDLADg,
jk-mnsaURCQ41sdnm+yROfE0A, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
andrew-zrmu5oMJ5Fs, alistair-Y4h6yKqj69EXC2x5gXVKYQ,
benh-XVmvHMARGAS8U2dJNN8I7kB+6BGkLq7r
From: Chris Bostic <cbostic-r/Jw6+rmf7HQT0dZR+AlfA@public.gmane.org>
Introduction of the IBM 'Flexible Support Interface' (FSI) bus device
driver. FSI is a high fan out serial bus consisting of a clock and a serial
data line capable of running at speeds up to 166 MHz.
This set provides the basic framework to add FSI extensions to the
Linux bus and device models. Master specific implementations are
defined to utilize the core FSI function.
In Linux, we have a core FSI "bus type", along with drivers for FSI
masters and engines.
The FSI master drivers expose a read/write interface to the bus address
space. The master drivers are under drivers/fsi/fsi-master-*.c.
The core handles probing and discovery of slaves and slave
engines, using those read/write interfaces. It is responsible for
creating the endpoint Linux devices corresponding to the discovered
engines on each slave.
Slave engines are identified by an 'engine' type, and an optional
version. Engine, a.k.a. client, drivers are matched and bound to these
engines during discovery.
This patch set does not include extended FSI function such as:
* Hub master support
* Cascaded master support
* Application layer hot plug notification
* Application layer FSI bus status interface
Common FSI terminology:
* Master
Controller of the FSI bus. Only the master is allowed to control the
clock line and is the initiator of all transactions on a bus.
* Slave
The receiver or target of a master initiated transaction. The slave
cannot initiate communications on a bus and must respond to any
master requests for data.
* CFAM
Stands for Common Field replaceable unit Access Macro. A CFAM is an
ASIC residing in any device requiring FSI communications. CFAMs
consist of an array of hardware 'engines' used for various purposes.
I2C masters, UARTs, General Purpose IO hardware are common types of
these engines.
* Configuration Space / Table
A table contained at the beginning of each CFAM address space.
This table lists information such as the CFAM's ID, which engine types
and versions it has available, as well as its addressing range.
* FSI Engine driver
A device driver that registers with the FSI core so that it can access
devices it owns on an FSI bus.
Chris Bostic (5):
drivers/fsi: Set up links for slave communication
drivers/fsi: Set slave SMODE to init communication
drivers/fsi: Add master unscan
drivers/fsi: Add documentation for GPIO bindings
drivers/fsi: Add GPIO based FSI master
Jeremy Kerr (11):
drivers/fsi: Add empty fsi bus definitions
drivers/fsi: Add device & driver definitions
drivers/fsi: add driver to device matches
drivers/fsi: Add fsi master definition
drivers/fsi: Add fake master driver
drivers/fsi: Add slave definition
drivers/fsi: Add empty master scan
drivers/fsi: Add crc4 helpers
drivers/fsi: Implement slave initialisation
drivers/fsi: scan slaves & register devices
drivers/fsi: Add device read/write/peek functions
.../devicetree/bindings/fsi/fsi-master-gpio.txt | 21 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/fsi/Kconfig | 29 ++
drivers/fsi/Makefile | 4 +
drivers/fsi/fsi-core.c | 514 +++++++++++++++++++
drivers/fsi/fsi-master-fake.c | 95 ++++
drivers/fsi/fsi-master-gpio.c | 552 +++++++++++++++++++++
drivers/fsi/fsi-master.h | 62 +++
include/linux/fsi.h | 60 +++
10 files changed, 1340 insertions(+)
create mode 100644 Documentation/devicetree/bindings/fsi/fsi-master-gpio.txt
create mode 100644 drivers/fsi/Kconfig
create mode 100644 drivers/fsi/Makefile
create mode 100644 drivers/fsi/fsi-core.c
create mode 100644 drivers/fsi/fsi-master-fake.c
create mode 100644 drivers/fsi/fsi-master-gpio.c
create mode 100644 drivers/fsi/fsi-master.h
create mode 100644 include/linux/fsi.h
--
1.8.2.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v5 11/14] ASoC: add simple-graph-card document
From: Kuninori Morimoto @ 2016-12-07 0:10 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Brown, Linux-ALSA, Liam Girdwood, Simon, Laurent, Guennadi,
Grant Likely, Frank Rowand, Linux-DT, Linux-Kernel
In-Reply-To: <CAL_JsqLyYE_nmGfPEF_H9NxKK1HX1BbwWkUmw-PSWo6TANr5ZQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
Hi Rob
> > Do you mean, is this OK for OF graph ?
>
> Yes, something like this.
Wow!! Thanks !!
it makes new OF-graph easier !!
> > in driver point of view, "I2S" is sound card here.
>
> Well, that seems odd to me because I2S should just be the h/w block
> that interfaces to I2S/SSI signals. I'd expect you still have a card
> node that references these nodes. Maybe it just references the DSP and
> then you walk the graph from there to find the I2S controller and
> codec.
If my understanding was correct, this is good ?
Card {
ports {
port@0 {
card-dsp: endpoint {
remote-endpoint = <&dsp>;
};
};
port@1 {
card-codec: endpoint {
remote-endpoint = <&codec>;
};
}
}
}
DSP {
port {
dsp: endpoint {
remote-endpoint = <&card-dsp>;
}
}
}
Codec {
port {
codec: endpoint {
remote-endpoint = <&card-codec>;
}
}
}
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH v5 13/13] net: ethernet: ti: cpts: fix overflow check period
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko, John Stultz
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 10 +++++++---
drivers/net/ethernet/ti/cpts.h | 4 +---
2 files changed, 8 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index ebd413a..0c0d48e 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -245,7 +245,7 @@ static void cpts_overflow_check(struct work_struct *work)
cpts_ptp_gettime(&cpts->info, &ts);
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec, ts.tv_nsec);
- schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
+ schedule_delayed_work(&cpts->overflow_work, cpts->ov_check_period);
}
static int cpts_match(struct sk_buff *skb, unsigned int ptp_class,
@@ -378,8 +378,7 @@ int cpts_register(struct cpts *cpts)
}
cpts->phc_index = ptp_clock_index(cpts->clock);
- schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
-
+ schedule_delayed_work(&cpts->overflow_work, cpts->ov_check_period);
return 0;
err_ptp:
@@ -423,6 +422,11 @@ static void cpts_calc_mult_shift(struct cpts *cpts)
if (maxsec > 10)
maxsec = 10;
+ /* Calc overflow check period (maxsec / 2) */
+ cpts->ov_check_period = (HZ * maxsec) / 2;
+ dev_info(cpts->dev, "cpts: overflow check period %lu (jiffies)\n",
+ cpts->ov_check_period);
+
if (cpts->cc.mult || cpts->cc.shift)
return;
diff --git a/drivers/net/ethernet/ti/cpts.h b/drivers/net/ethernet/ti/cpts.h
index 5da23af..c96eca2 100644
--- a/drivers/net/ethernet/ti/cpts.h
+++ b/drivers/net/ethernet/ti/cpts.h
@@ -97,9 +97,6 @@ enum {
CPTS_EV_TX, /* Ethernet Transmit Event */
};
-/* This covers any input clock up to about 500 MHz. */
-#define CPTS_OVERFLOW_PERIOD (HZ * 8)
-
#define CPTS_FIFO_DEPTH 16
#define CPTS_MAX_EVENTS 32
@@ -127,6 +124,7 @@ struct cpts {
struct list_head events;
struct list_head pool;
struct cpts_event pool_data[CPTS_MAX_EVENTS];
+ unsigned long ov_check_period;
};
void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb);
--
2.10.1
^ permalink raw reply related
* [PATCH v5 12/13] net: ethernet: ti: cpts: calc mult and shift from refclk freq
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko, John Stultz
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
The cyclecounter mult and shift values can be calculated based on the
CPTS rfclk frequency and timekeepnig framework provides required algos
and API's.
Hence, calc mult and shift basing on CPTS rfclk frequency if both
cpts_clock_shift and cpts_clock_mult properties are not provided in DT (the
basis of calculation algorithm is borrowed from
__clocksource_update_freq_scale() commit 7d2f944a2b83 ("clocksource:
Provide a generic mult/shift factor calculation")). After this change
cpts_clock_shift and cpts_clock_mult DT properties will become optional.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
Documentation/devicetree/bindings/net/cpsw.txt | 8 +++--
drivers/net/ethernet/ti/cpts.c | 50 ++++++++++++++++++++++----
2 files changed, 48 insertions(+), 10 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt
index 5ad439f..ebda7c9 100644
--- a/Documentation/devicetree/bindings/net/cpsw.txt
+++ b/Documentation/devicetree/bindings/net/cpsw.txt
@@ -20,8 +20,6 @@ Required properties:
- slaves : Specifies number for slaves
- active_slave : Specifies the slave to use for time stamping,
ethtool and SIOCGMIIPHY
-- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds
-- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds
Optional properties:
- ti,hwmods : Must be "cpgmac0"
@@ -35,7 +33,11 @@ Optional properties:
For example in dra72x-evm, pcf gpio has to be
driven low so that cpsw slave 0 and phy data
lines are connected via mux.
-
+- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds
+- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds
+ Mult and shift will be calculated basing on CPTS
+ rftclk frequency if both cpts_clock_shift and
+ cpts_clock_mult properties are not provided.
Slave Properties:
Required properties:
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index cb844ed..ebd413a 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -405,18 +405,52 @@ void cpts_unregister(struct cpts *cpts)
}
EXPORT_SYMBOL_GPL(cpts_unregister);
+static void cpts_calc_mult_shift(struct cpts *cpts)
+{
+ u64 frac, maxsec, ns;
+ u32 freq;
+
+ freq = clk_get_rate(cpts->refclk);
+
+ /* Calc the maximum number of seconds which we can run before
+ * wrapping around.
+ */
+ maxsec = cpts->cc.mask;
+ do_div(maxsec, freq);
+ /* limit conversation rate to 10 sec as higher values will produce
+ * too small mult factors and so reduce the conversion accuracy
+ */
+ if (maxsec > 10)
+ maxsec = 10;
+
+ if (cpts->cc.mult || cpts->cc.shift)
+ return;
+
+ clocks_calc_mult_shift(&cpts->cc.mult, &cpts->cc.shift,
+ freq, NSEC_PER_SEC, maxsec);
+
+ frac = 0;
+ ns = cyclecounter_cyc2ns(&cpts->cc, freq, cpts->cc.mask, &frac);
+
+ dev_info(cpts->dev,
+ "CPTS: ref_clk_freq:%u calc_mult:%u calc_shift:%u error:%lld nsec/sec\n",
+ freq, cpts->cc.mult, cpts->cc.shift, (ns - NSEC_PER_SEC));
+}
+
static int cpts_of_parse(struct cpts *cpts, struct device_node *node)
{
int ret = -EINVAL;
u32 prop;
- if (of_property_read_u32(node, "cpts_clock_mult", &prop))
- goto of_error;
- cpts->cc.mult = prop;
+ if (!of_property_read_u32(node, "cpts_clock_mult", &prop))
+ cpts->cc.mult = prop;
- if (of_property_read_u32(node, "cpts_clock_shift", &prop))
- goto of_error;
- cpts->cc.shift = prop;
+ if (!of_property_read_u32(node, "cpts_clock_shift", &prop))
+ cpts->cc.shift = prop;
+
+ if ((cpts->cc.mult && !cpts->cc.shift) ||
+ (!cpts->cc.mult && cpts->cc.shift))
+ goto of_error;
return 0;
@@ -454,11 +488,13 @@ struct cpts *cpts_create(struct device *dev, void __iomem *regs,
cpts->cc.read = cpts_systim_read;
cpts->cc.mask = CLOCKSOURCE_MASK(32);
+ cpts->info = cpts_info;
+
+ cpts_calc_mult_shift(cpts);
/* save cc.mult original value as it can be modified
* by cpts_ptp_adjfreq().
*/
cpts->cc_mult = cpts->cc.mult;
- cpts->info = cpts_info;
return cpts;
}
--
2.10.1
^ permalink raw reply related
* [PATCH v5 11/13] clocksource: export the clocks_calc_mult_shift to use by timestamp code
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner, John Stultz,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
From: Murali Karicheri <m-karicheri2@ti.com>
The CPSW CPTS driver is capable of doing timestamping on tx/rx packets and
requires to know mult and shift factors for timestamp conversion from raw
value to nanoseconds (ptp clock). Now these mult and shift factors are
calculated manually and provided through DT, which makes very hard to
support of a lot number of platforms, especially if CPTS refclk is not the
same for some kind of boards and depends on efuse settings (Keystone 2
platforms). Hence, export clocks_calc_mult_shift() to allow drivers like
CPSW CPTS (and other ptp drivesr) to benefit from automaitc calculation of
mult and shift factors.
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
---
kernel/time/clocksource.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/kernel/time/clocksource.c b/kernel/time/clocksource.c
index 7e4fad7..150242c 100644
--- a/kernel/time/clocksource.c
+++ b/kernel/time/clocksource.c
@@ -89,6 +89,7 @@ clocks_calc_mult_shift(u32 *mult, u32 *shift, u32 from, u32 to, u32 maxsec)
*mult = tmp;
*shift = sft;
}
+EXPORT_SYMBOL_GPL(clocks_calc_mult_shift);
/*[Clocksource internal variables]---------
* curr_clocksource:
--
2.10.1
^ permalink raw reply related
* [PATCH v5 10/13] net: ethernet: ti: cpts: move dt props parsing to cpts driver
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
Move DT properties parsing into CPTS driver to simplify CPSW
code and CPTS driver porting on other SoC in the future
(like Keystone 2) - with this change it will not be required
to add the same DT parsing code in Keystone 2 NETCP driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/net/ethernet/ti/cpsw.c | 16 +---------------
drivers/net/ethernet/ti/cpsw.h | 2 --
drivers/net/ethernet/ti/cpts.c | 34 ++++++++++++++++++++++++++++++----
drivers/net/ethernet/ti/cpts.h | 5 +++--
4 files changed, 34 insertions(+), 23 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index a9a8354..b62d958 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -2524,18 +2524,6 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
}
data->active_slave = prop;
- if (of_property_read_u32(node, "cpts_clock_mult", &prop)) {
- dev_err(&pdev->dev, "Missing cpts_clock_mult property in the DT.\n");
- return -EINVAL;
- }
- data->cpts_clock_mult = prop;
-
- if (of_property_read_u32(node, "cpts_clock_shift", &prop)) {
- dev_err(&pdev->dev, "Missing cpts_clock_shift property in the DT.\n");
- return -EINVAL;
- }
- data->cpts_clock_shift = prop;
-
data->slave_data = devm_kzalloc(&pdev->dev, data->slaves
* sizeof(struct cpsw_slave_data),
GFP_KERNEL);
@@ -2990,9 +2978,7 @@ static int cpsw_probe(struct platform_device *pdev)
goto clean_dma_ret;
}
- cpsw->cpts = cpts_create(cpsw->dev, cpts_regs,
- cpsw->data.cpts_clock_mult,
- cpsw->data.cpts_clock_shift);
+ cpsw->cpts = cpts_create(cpsw->dev, cpts_regs, cpsw->dev->of_node);
if (IS_ERR(cpsw->cpts)) {
ret = PTR_ERR(cpsw->cpts);
goto clean_ale_ret;
diff --git a/drivers/net/ethernet/ti/cpsw.h b/drivers/net/ethernet/ti/cpsw.h
index 16b54c6..6c3037a 100644
--- a/drivers/net/ethernet/ti/cpsw.h
+++ b/drivers/net/ethernet/ti/cpsw.h
@@ -31,8 +31,6 @@ struct cpsw_platform_data {
u32 channels; /* number of cpdma channels (symmetric) */
u32 slaves; /* number of slave cpgmac ports */
u32 active_slave; /* time stamping, ethtool and SIOCGMIIPHY slave */
- u32 cpts_clock_mult; /* convert input clock ticks to nanoseconds */
- u32 cpts_clock_shift; /* convert input clock ticks to nanoseconds */
u32 ale_entries; /* ale table size */
u32 bd_ram_size; /*buffer descriptor ram size */
u32 mac_control; /* Mac control register */
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 31cd83f..cb844ed 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -405,10 +405,31 @@ void cpts_unregister(struct cpts *cpts)
}
EXPORT_SYMBOL_GPL(cpts_unregister);
+static int cpts_of_parse(struct cpts *cpts, struct device_node *node)
+{
+ int ret = -EINVAL;
+ u32 prop;
+
+ if (of_property_read_u32(node, "cpts_clock_mult", &prop))
+ goto of_error;
+ cpts->cc.mult = prop;
+
+ if (of_property_read_u32(node, "cpts_clock_shift", &prop))
+ goto of_error;
+ cpts->cc.shift = prop;
+
+ return 0;
+
+of_error:
+ dev_err(cpts->dev, "CPTS: Missing property in the DT.\n");
+ return ret;
+}
+
struct cpts *cpts_create(struct device *dev, void __iomem *regs,
- u32 mult, u32 shift)
+ struct device_node *node)
{
struct cpts *cpts;
+ int ret;
cpts = devm_kzalloc(dev, sizeof(*cpts), GFP_KERNEL);
if (!cpts)
@@ -419,6 +440,10 @@ struct cpts *cpts_create(struct device *dev, void __iomem *regs,
spin_lock_init(&cpts->lock);
INIT_DELAYED_WORK(&cpts->overflow_work, cpts_overflow_check);
+ ret = cpts_of_parse(cpts, node);
+ if (ret)
+ return ERR_PTR(ret);
+
cpts->refclk = devm_clk_get(dev, "cpts");
if (IS_ERR(cpts->refclk)) {
dev_err(dev, "Failed to get cpts refclk\n");
@@ -429,9 +454,10 @@ struct cpts *cpts_create(struct device *dev, void __iomem *regs,
cpts->cc.read = cpts_systim_read;
cpts->cc.mask = CLOCKSOURCE_MASK(32);
- cpts->cc.shift = shift;
- cpts->cc_mult = mult;
- cpts->cc.mult = mult;
+ /* save cc.mult original value as it can be modified
+ * by cpts_ptp_adjfreq().
+ */
+ cpts->cc_mult = cpts->cc.mult;
cpts->info = cpts_info;
return cpts;
diff --git a/drivers/net/ethernet/ti/cpts.h b/drivers/net/ethernet/ti/cpts.h
index e7d857c..5da23af 100644
--- a/drivers/net/ethernet/ti/cpts.h
+++ b/drivers/net/ethernet/ti/cpts.h
@@ -27,6 +27,7 @@
#include <linux/clocksource.h>
#include <linux/device.h>
#include <linux/list.h>
+#include <linux/of.h>
#include <linux/ptp_clock_kernel.h>
#include <linux/skbuff.h>
#include <linux/timecounter.h>
@@ -133,7 +134,7 @@ void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb);
int cpts_register(struct cpts *cpts);
void cpts_unregister(struct cpts *cpts);
struct cpts *cpts_create(struct device *dev, void __iomem *regs,
- u32 mult, u32 shift);
+ struct device_node *node);
void cpts_release(struct cpts *cpts);
static inline void cpts_rx_enable(struct cpts *cpts, int enable)
@@ -168,7 +169,7 @@ static inline void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
static inline
struct cpts *cpts_create(struct device *dev, void __iomem *regs,
- u32 mult, u32 shift)
+ struct device_node *node)
{
return NULL;
}
--
2.10.1
^ permalink raw reply related
* [PATCH v5 09/13] net: ethernet: ti: cpts: rework initialization/deinitialization
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
The current implementation CPTS initialization and deinitialization
(represented by cpts_register/unregister()) does too many static
initialization from .ndo_open(), which is reasonable to do once at probe
time instead, and also require caller to allocate memory for struct cpts,
which is internal for CPTS driver in general.
This patch splits CPTS initialization and deinitialization on two parts:
- static initializtion cpts_create()/cpts_release() which expected to be
executed when parent driver is probed/removed;
- dynamic part cpts_register/unregister() which expected to be executed
when network device is opened/closed.
As result, current code of CPTS parent driver - CPSW - will be simplified
(and it also will allow simplify adding support for Keystone 2 devices in
the future), plus more initialization errors will be catched earlier. In
addition, this change allows to clean up cpts.h for the case when CPTS is
disabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/net/ethernet/ti/cpsw.c | 24 +++++-----
drivers/net/ethernet/ti/cpts.c | 99 +++++++++++++++++++++++++-----------------
drivers/net/ethernet/ti/cpts.h | 26 ++++++++---
3 files changed, 92 insertions(+), 57 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 7599895..a9a8354 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1487,9 +1487,7 @@ static int cpsw_ndo_open(struct net_device *ndev)
if (ret < 0)
goto err_cleanup;
- if (cpts_register(cpsw->dev, cpsw->cpts,
- cpsw->data.cpts_clock_mult,
- cpsw->data.cpts_clock_shift))
+ if (cpts_register(cpsw->cpts))
dev_err(priv->dev, "error registering cpts device\n");
}
@@ -2796,6 +2794,7 @@ static int cpsw_probe(struct platform_device *pdev)
struct cpdma_params dma_params;
struct cpsw_ale_params ale_params;
void __iomem *ss_regs;
+ void __iomem *cpts_regs;
struct resource *res, *ss_res;
const struct of_device_id *of_id;
struct gpio_descs *mode;
@@ -2823,12 +2822,6 @@ static int cpsw_probe(struct platform_device *pdev)
priv->dev = &ndev->dev;
priv->msg_enable = netif_msg_init(debug_level, CPSW_DEBUG);
cpsw->rx_packet_max = max(rx_packet_max, 128);
- cpsw->cpts = devm_kzalloc(&pdev->dev, sizeof(struct cpts), GFP_KERNEL);
- if (!cpsw->cpts) {
- dev_err(&pdev->dev, "error allocating cpts\n");
- ret = -ENOMEM;
- goto clean_ndev_ret;
- }
mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);
if (IS_ERR(mode)) {
@@ -2916,7 +2909,7 @@ static int cpsw_probe(struct platform_device *pdev)
switch (cpsw->version) {
case CPSW_VERSION_1:
cpsw->host_port_regs = ss_regs + CPSW1_HOST_PORT_OFFSET;
- cpsw->cpts->reg = ss_regs + CPSW1_CPTS_OFFSET;
+ cpts_regs = ss_regs + CPSW1_CPTS_OFFSET;
cpsw->hw_stats = ss_regs + CPSW1_HW_STATS;
dma_params.dmaregs = ss_regs + CPSW1_CPDMA_OFFSET;
dma_params.txhdp = ss_regs + CPSW1_STATERAM_OFFSET;
@@ -2930,7 +2923,7 @@ static int cpsw_probe(struct platform_device *pdev)
case CPSW_VERSION_3:
case CPSW_VERSION_4:
cpsw->host_port_regs = ss_regs + CPSW2_HOST_PORT_OFFSET;
- cpsw->cpts->reg = ss_regs + CPSW2_CPTS_OFFSET;
+ cpts_regs = ss_regs + CPSW2_CPTS_OFFSET;
cpsw->hw_stats = ss_regs + CPSW2_HW_STATS;
dma_params.dmaregs = ss_regs + CPSW2_CPDMA_OFFSET;
dma_params.txhdp = ss_regs + CPSW2_STATERAM_OFFSET;
@@ -2997,6 +2990,14 @@ static int cpsw_probe(struct platform_device *pdev)
goto clean_dma_ret;
}
+ cpsw->cpts = cpts_create(cpsw->dev, cpts_regs,
+ cpsw->data.cpts_clock_mult,
+ cpsw->data.cpts_clock_shift);
+ if (IS_ERR(cpsw->cpts)) {
+ ret = PTR_ERR(cpsw->cpts);
+ goto clean_ale_ret;
+ }
+
ndev->irq = platform_get_irq(pdev, 1);
if (ndev->irq < 0) {
dev_err(priv->dev, "error getting irq resource\n");
@@ -3112,6 +3113,7 @@ static int cpsw_remove(struct platform_device *pdev)
unregister_netdev(cpsw->slaves[1].ndev);
unregister_netdev(ndev);
+ cpts_release(cpsw->cpts);
cpsw_ale_destroy(cpsw->ale);
cpdma_ctlr_destroy(cpsw->dma);
cpsw_remove_dt(pdev);
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index fe1bb7f..31cd83f 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -248,24 +248,6 @@ static void cpts_overflow_check(struct work_struct *work)
schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
}
-static void cpts_clk_init(struct device *dev, struct cpts *cpts)
-{
- if (!cpts->refclk) {
- cpts->refclk = devm_clk_get(dev, "cpts");
- if (IS_ERR(cpts->refclk)) {
- dev_err(dev, "Failed to get cpts refclk\n");
- cpts->refclk = NULL;
- return;
- }
- }
- clk_prepare_enable(cpts->refclk);
-}
-
-static void cpts_clk_release(struct cpts *cpts)
-{
- clk_disable_unprepare(cpts->refclk);
-}
-
static int cpts_match(struct sk_buff *skb, unsigned int ptp_class,
u16 ts_seqid, u8 ts_msgtype)
{
@@ -372,34 +354,23 @@ void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
}
EXPORT_SYMBOL_GPL(cpts_tx_timestamp);
-int cpts_register(struct device *dev, struct cpts *cpts,
- u32 mult, u32 shift)
+int cpts_register(struct cpts *cpts)
{
int err, i;
- cpts->info = cpts_info;
- spin_lock_init(&cpts->lock);
-
- cpts->cc.read = cpts_systim_read;
- cpts->cc.mask = CLOCKSOURCE_MASK(32);
- cpts->cc_mult = mult;
- cpts->cc.mult = mult;
- cpts->cc.shift = shift;
-
INIT_LIST_HEAD(&cpts->events);
INIT_LIST_HEAD(&cpts->pool);
for (i = 0; i < CPTS_MAX_EVENTS; i++)
list_add(&cpts->pool_data[i].list, &cpts->pool);
- cpts_clk_init(dev, cpts);
+ clk_enable(cpts->refclk);
+
cpts_write32(cpts, CPTS_EN, control);
cpts_write32(cpts, TS_PEND_EN, int_enable);
timecounter_init(&cpts->tc, &cpts->cc, ktime_to_ns(ktime_get_real()));
- INIT_DELAYED_WORK(&cpts->overflow_work, cpts_overflow_check);
-
- cpts->clock = ptp_clock_register(&cpts->info, dev);
+ cpts->clock = ptp_clock_register(&cpts->info, cpts->dev);
if (IS_ERR(cpts->clock)) {
err = PTR_ERR(cpts->clock);
cpts->clock = NULL;
@@ -412,27 +383,73 @@ int cpts_register(struct device *dev, struct cpts *cpts,
return 0;
err_ptp:
- if (cpts->refclk)
- cpts_clk_release(cpts);
+ clk_disable(cpts->refclk);
return err;
}
EXPORT_SYMBOL_GPL(cpts_register);
void cpts_unregister(struct cpts *cpts)
{
- if (cpts->clock) {
- ptp_clock_unregister(cpts->clock);
- cancel_delayed_work_sync(&cpts->overflow_work);
- }
+ if (WARN_ON(!cpts->clock))
+ return;
+
+ cancel_delayed_work_sync(&cpts->overflow_work);
+
+ ptp_clock_unregister(cpts->clock);
+ cpts->clock = NULL;
cpts_write32(cpts, 0, int_enable);
cpts_write32(cpts, 0, control);
- if (cpts->refclk)
- cpts_clk_release(cpts);
+ clk_disable(cpts->refclk);
}
EXPORT_SYMBOL_GPL(cpts_unregister);
+struct cpts *cpts_create(struct device *dev, void __iomem *regs,
+ u32 mult, u32 shift)
+{
+ struct cpts *cpts;
+
+ cpts = devm_kzalloc(dev, sizeof(*cpts), GFP_KERNEL);
+ if (!cpts)
+ return ERR_PTR(-ENOMEM);
+
+ cpts->dev = dev;
+ cpts->reg = (struct cpsw_cpts __iomem *)regs;
+ spin_lock_init(&cpts->lock);
+ INIT_DELAYED_WORK(&cpts->overflow_work, cpts_overflow_check);
+
+ cpts->refclk = devm_clk_get(dev, "cpts");
+ if (IS_ERR(cpts->refclk)) {
+ dev_err(dev, "Failed to get cpts refclk\n");
+ return ERR_PTR(PTR_ERR(cpts->refclk));
+ }
+
+ clk_prepare(cpts->refclk);
+
+ cpts->cc.read = cpts_systim_read;
+ cpts->cc.mask = CLOCKSOURCE_MASK(32);
+ cpts->cc.shift = shift;
+ cpts->cc_mult = mult;
+ cpts->cc.mult = mult;
+ cpts->info = cpts_info;
+
+ return cpts;
+}
+EXPORT_SYMBOL_GPL(cpts_create);
+
+void cpts_release(struct cpts *cpts)
+{
+ if (!cpts)
+ return;
+
+ if (WARN_ON(!cpts->refclk))
+ return;
+
+ clk_unprepare(cpts->refclk);
+}
+EXPORT_SYMBOL_GPL(cpts_release);
+
MODULE_LICENSE("GPL v2");
MODULE_DESCRIPTION("TI CPTS driver");
MODULE_AUTHOR("Richard Cochran <richardcochran@gmail.com>");
diff --git a/drivers/net/ethernet/ti/cpts.h b/drivers/net/ethernet/ti/cpts.h
index 29a1e80c..e7d857c 100644
--- a/drivers/net/ethernet/ti/cpts.h
+++ b/drivers/net/ethernet/ti/cpts.h
@@ -20,6 +20,8 @@
#ifndef _TI_CPTS_H_
#define _TI_CPTS_H_
+#if IS_ENABLED(CONFIG_TI_CPTS)
+
#include <linux/clk.h>
#include <linux/clkdev.h>
#include <linux/clocksource.h>
@@ -108,10 +110,10 @@ struct cpts_event {
};
struct cpts {
+ struct device *dev;
struct cpsw_cpts __iomem *reg;
int tx_enable;
int rx_enable;
-#if IS_ENABLED(CONFIG_TI_CPTS)
struct ptp_clock_info info;
struct ptp_clock *clock;
spinlock_t lock; /* protects time registers */
@@ -124,14 +126,15 @@ struct cpts {
struct list_head events;
struct list_head pool;
struct cpts_event pool_data[CPTS_MAX_EVENTS];
-#endif
};
-#if IS_ENABLED(CONFIG_TI_CPTS)
void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb);
void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb);
-int cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift);
+int cpts_register(struct cpts *cpts);
void cpts_unregister(struct cpts *cpts);
+struct cpts *cpts_create(struct device *dev, void __iomem *regs,
+ u32 mult, u32 shift);
+void cpts_release(struct cpts *cpts);
static inline void cpts_rx_enable(struct cpts *cpts, int enable)
{
@@ -154,6 +157,8 @@ static inline bool cpts_is_tx_enabled(struct cpts *cpts)
}
#else
+struct cpts;
+
static inline void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
}
@@ -161,8 +166,19 @@ static inline void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
}
+static inline
+struct cpts *cpts_create(struct device *dev, void __iomem *regs,
+ u32 mult, u32 shift)
+{
+ return NULL;
+}
+
+static inline void cpts_release(struct cpts *cpts)
+{
+}
+
static inline int
-cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift)
+cpts_register(struct cpts *cpts)
{
return 0;
}
--
2.10.1
^ permalink raw reply related
* [PATCH v5 08/13] net: ethernet: ti: cpts: drop excessive writes to CTRL and INT_EN regs
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
CPTS module and IRQs are always enabled when CPTS is registered,
before starting overflow check work, and disabled during
deregistration, when overflow check work has been canceled already.
So, It doesn't require to (re)enable CPTS module and IRQs in
cpts_overflow_check().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 2 --
1 file changed, 2 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 7ab1fa7..fe1bb7f 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -243,8 +243,6 @@ static void cpts_overflow_check(struct work_struct *work)
struct timespec64 ts;
struct cpts *cpts = container_of(work, struct cpts, overflow_work.work);
- cpts_write32(cpts, CPTS_EN, control);
- cpts_write32(cpts, TS_PEND_EN, int_enable);
cpts_ptp_gettime(&cpts->info, &ts);
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec, ts.tv_nsec);
schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
--
2.10.1
^ permalink raw reply related
* [PATCH v5 07/13] net: ethernet: ti: cpts: clean up event list if event pool is empty
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev-u79uwXL29TY76Z2rM5mHXA, Mugunthan V N,
Richard Cochran
Cc: Sekhar Nori, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Murali Karicheri, Wingman Kwok,
Thomas Gleixner, Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko-l0cyMroinI0@public.gmane.org>
From: WingMan Kwok <w-kwok2-l0cyMroinI0@public.gmane.org>
When a CPTS user does not exit gracefully by disabling cpts
timestamping and leaving a joined multicast group, the system
continues to receive and timestamps the ptp packets which eventually
occupy all the event list entries. When this happns, the added code
tries to remove some list entries which are expired.
Signed-off-by: WingMan Kwok <w-kwok2-l0cyMroinI0@public.gmane.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko-l0cyMroinI0@public.gmane.org>
---
drivers/net/ethernet/ti/cpts.c | 26 ++++++++++++++++++++++++--
1 file changed, 24 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index d3c1ac5..7ab1fa7 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -57,6 +57,26 @@ static int cpts_fifo_pop(struct cpts *cpts, u32 *high, u32 *low)
return -1;
}
+static int cpts_purge_events(struct cpts *cpts)
+{
+ struct list_head *this, *next;
+ struct cpts_event *event;
+ int removed = 0;
+
+ list_for_each_safe(this, next, &cpts->events) {
+ event = list_entry(this, struct cpts_event, list);
+ if (event_expired(event)) {
+ list_del_init(&event->list);
+ list_add(&event->list, &cpts->pool);
+ ++removed;
+ }
+ }
+
+ if (removed)
+ pr_debug("cpts: event pool cleaned up %d\n", removed);
+ return removed ? 0 : -1;
+}
+
/*
* Returns zero if matching event type was found.
*/
@@ -69,10 +89,12 @@ static int cpts_fifo_read(struct cpts *cpts, int match)
for (i = 0; i < CPTS_FIFO_DEPTH; i++) {
if (cpts_fifo_pop(cpts, &hi, &lo))
break;
- if (list_empty(&cpts->pool)) {
- pr_err("cpts: event pool is empty\n");
+
+ if (list_empty(&cpts->pool) && cpts_purge_events(cpts)) {
+ pr_err("cpts: event pool empty\n");
return -1;
}
+
event = list_first_entry(&cpts->pool, struct cpts_event, list);
event->tmo = jiffies + 2;
event->high = hi;
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 06/13] net: ethernet: ti: cpts: disable cpts when unregistered
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
The cpts now is left enabled after unregistration.
Hence, disable it in cpts_unregister().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 3dda6d5..d3c1ac5 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -404,6 +404,10 @@ void cpts_unregister(struct cpts *cpts)
ptp_clock_unregister(cpts->clock);
cancel_delayed_work_sync(&cpts->overflow_work);
}
+
+ cpts_write32(cpts, 0, int_enable);
+ cpts_write32(cpts, 0, control);
+
if (cpts->refclk)
cpts_clk_release(cpts);
}
--
2.10.1
^ permalink raw reply related
* [PATCH v5 05/13] net: ethernet: ti: cpts: fix registration order
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
The ptp clock registered before spinlock, which is protecting it, and
before timecounter and cyclecounter initialization in cpts_register().
So, ensure that ptp clock is registered the last, after everything
else is done.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 24 ++++++++++++++----------
1 file changed, 14 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 61198f1..3dda6d5 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -356,15 +356,8 @@ int cpts_register(struct device *dev, struct cpts *cpts,
u32 mult, u32 shift)
{
int err, i;
- unsigned long flags;
cpts->info = cpts_info;
- cpts->clock = ptp_clock_register(&cpts->info, dev);
- if (IS_ERR(cpts->clock)) {
- err = PTR_ERR(cpts->clock);
- cpts->clock = NULL;
- return err;
- }
spin_lock_init(&cpts->lock);
cpts->cc.read = cpts_systim_read;
@@ -382,15 +375,26 @@ int cpts_register(struct device *dev, struct cpts *cpts,
cpts_write32(cpts, CPTS_EN, control);
cpts_write32(cpts, TS_PEND_EN, int_enable);
- spin_lock_irqsave(&cpts->lock, flags);
timecounter_init(&cpts->tc, &cpts->cc, ktime_to_ns(ktime_get_real()));
- spin_unlock_irqrestore(&cpts->lock, flags);
INIT_DELAYED_WORK(&cpts->overflow_work, cpts_overflow_check);
- schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
+ cpts->clock = ptp_clock_register(&cpts->info, dev);
+ if (IS_ERR(cpts->clock)) {
+ err = PTR_ERR(cpts->clock);
+ cpts->clock = NULL;
+ goto err_ptp;
+ }
cpts->phc_index = ptp_clock_index(cpts->clock);
+
+ schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
+
return 0;
+
+err_ptp:
+ if (cpts->refclk)
+ cpts_clk_release(cpts);
+ return err;
}
EXPORT_SYMBOL_GPL(cpts_register);
--
2.10.1
^ permalink raw reply related
* [PATCH v5 04/13] net: ethernet: ti: cpts: fix unbalanced clk api usage in cpts_register/unregister
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
There are two issues with TI CPTS code which are reproducible when TI
CPSW ethX device passes few up/down iterations:
- cpts refclk prepare counter continuously incremented after each
up/down iteration;
- devm_clk_get(dev, "cpts") is called many times.
Hence, fix these issues by using clk_disable_unprepare() in
cpts_clk_release() and skipping devm_clk_get() if cpts refclk has been
acquired already.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 14 ++++++++------
1 file changed, 8 insertions(+), 6 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 8cb0369..61198f1 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -230,18 +230,20 @@ static void cpts_overflow_check(struct work_struct *work)
static void cpts_clk_init(struct device *dev, struct cpts *cpts)
{
- cpts->refclk = devm_clk_get(dev, "cpts");
- if (IS_ERR(cpts->refclk)) {
- dev_err(dev, "Failed to get cpts refclk\n");
- cpts->refclk = NULL;
- return;
+ if (!cpts->refclk) {
+ cpts->refclk = devm_clk_get(dev, "cpts");
+ if (IS_ERR(cpts->refclk)) {
+ dev_err(dev, "Failed to get cpts refclk\n");
+ cpts->refclk = NULL;
+ return;
+ }
}
clk_prepare_enable(cpts->refclk);
}
static void cpts_clk_release(struct cpts *cpts)
{
- clk_disable(cpts->refclk);
+ clk_disable_unprepare(cpts->refclk);
}
static int cpts_match(struct sk_buff *skb, unsigned int ptp_class,
--
2.10.1
^ permalink raw reply related
* [PATCH v5 03/13] net: ethernet: ti: cpsw: minimize direct access to struct cpts
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
This will provide more flexibility in changing CPTS internals and also
required for further changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/net/ethernet/ti/cpsw.c | 28 +++++++++++++++-------------
drivers/net/ethernet/ti/cpts.h | 39 +++++++++++++++++++++++++++++++++++++++
2 files changed, 54 insertions(+), 13 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index 8fdb274..7599895 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1562,7 +1562,7 @@ static netdev_tx_t cpsw_ndo_start_xmit(struct sk_buff *skb,
}
if (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP &&
- cpsw->cpts->tx_enable)
+ cpts_is_tx_enabled(cpsw->cpts))
skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS;
skb_tx_timestamp(skb);
@@ -1601,7 +1601,8 @@ static void cpsw_hwtstamp_v1(struct cpsw_common *cpsw)
struct cpsw_slave *slave = &cpsw->slaves[cpsw->data.active_slave];
u32 ts_en, seq_id;
- if (!cpsw->cpts->tx_enable && !cpsw->cpts->rx_enable) {
+ if (!cpts_is_tx_enabled(cpsw->cpts) &&
+ !cpts_is_rx_enabled(cpsw->cpts)) {
slave_write(slave, 0, CPSW1_TS_CTL);
return;
}
@@ -1609,10 +1610,10 @@ static void cpsw_hwtstamp_v1(struct cpsw_common *cpsw)
seq_id = (30 << CPSW_V1_SEQ_ID_OFS_SHIFT) | ETH_P_1588;
ts_en = EVENT_MSG_BITS << CPSW_V1_MSG_TYPE_OFS;
- if (cpsw->cpts->tx_enable)
+ if (cpts_is_tx_enabled(cpsw->cpts))
ts_en |= CPSW_V1_TS_TX_EN;
- if (cpsw->cpts->rx_enable)
+ if (cpts_is_rx_enabled(cpsw->cpts))
ts_en |= CPSW_V1_TS_RX_EN;
slave_write(slave, ts_en, CPSW1_TS_CTL);
@@ -1635,20 +1636,20 @@ static void cpsw_hwtstamp_v2(struct cpsw_priv *priv)
case CPSW_VERSION_2:
ctrl &= ~CTRL_V2_ALL_TS_MASK;
- if (cpsw->cpts->tx_enable)
+ if (cpts_is_tx_enabled(cpsw->cpts))
ctrl |= CTRL_V2_TX_TS_BITS;
- if (cpsw->cpts->rx_enable)
+ if (cpts_is_rx_enabled(cpsw->cpts))
ctrl |= CTRL_V2_RX_TS_BITS;
break;
case CPSW_VERSION_3:
default:
ctrl &= ~CTRL_V3_ALL_TS_MASK;
- if (cpsw->cpts->tx_enable)
+ if (cpts_is_tx_enabled(cpsw->cpts))
ctrl |= CTRL_V3_TX_TS_BITS;
- if (cpsw->cpts->rx_enable)
+ if (cpts_is_rx_enabled(cpsw->cpts))
ctrl |= CTRL_V3_RX_TS_BITS;
break;
}
@@ -1684,7 +1685,7 @@ static int cpsw_hwtstamp_set(struct net_device *dev, struct ifreq *ifr)
switch (cfg.rx_filter) {
case HWTSTAMP_FILTER_NONE:
- cpts->rx_enable = 0;
+ cpts_rx_enable(cpts, 0);
break;
case HWTSTAMP_FILTER_ALL:
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
@@ -1700,14 +1701,14 @@ static int cpsw_hwtstamp_set(struct net_device *dev, struct ifreq *ifr)
case HWTSTAMP_FILTER_PTP_V2_EVENT:
case HWTSTAMP_FILTER_PTP_V2_SYNC:
case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ:
- cpts->rx_enable = 1;
+ cpts_rx_enable(cpts, 1);
cfg.rx_filter = HWTSTAMP_FILTER_PTP_V2_EVENT;
break;
default:
return -ERANGE;
}
- cpts->tx_enable = cfg.tx_type == HWTSTAMP_TX_ON;
+ cpts_tx_enable(cpts, cfg.tx_type == HWTSTAMP_TX_ON);
switch (cpsw->version) {
case CPSW_VERSION_1:
@@ -1736,8 +1737,9 @@ static int cpsw_hwtstamp_get(struct net_device *dev, struct ifreq *ifr)
return -EOPNOTSUPP;
cfg.flags = 0;
- cfg.tx_type = cpts->tx_enable ? HWTSTAMP_TX_ON : HWTSTAMP_TX_OFF;
- cfg.rx_filter = (cpts->rx_enable ?
+ cfg.tx_type = cpts_is_tx_enabled(cpts) ?
+ HWTSTAMP_TX_ON : HWTSTAMP_TX_OFF;
+ cfg.rx_filter = (cpts_is_rx_enabled(cpts) ?
HWTSTAMP_FILTER_PTP_V2_EVENT : HWTSTAMP_FILTER_NONE);
return copy_to_user(ifr->ifr_data, &cfg, sizeof(cfg)) ? -EFAULT : 0;
diff --git a/drivers/net/ethernet/ti/cpts.h b/drivers/net/ethernet/ti/cpts.h
index 416ba2c..29a1e80c 100644
--- a/drivers/net/ethernet/ti/cpts.h
+++ b/drivers/net/ethernet/ti/cpts.h
@@ -132,6 +132,27 @@ void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb);
void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb);
int cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift);
void cpts_unregister(struct cpts *cpts);
+
+static inline void cpts_rx_enable(struct cpts *cpts, int enable)
+{
+ cpts->rx_enable = enable;
+}
+
+static inline bool cpts_is_rx_enabled(struct cpts *cpts)
+{
+ return !!cpts->rx_enable;
+}
+
+static inline void cpts_tx_enable(struct cpts *cpts, int enable)
+{
+ cpts->tx_enable = enable;
+}
+
+static inline bool cpts_is_tx_enabled(struct cpts *cpts)
+{
+ return !!cpts->tx_enable;
+}
+
#else
static inline void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
@@ -149,6 +170,24 @@ cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift)
static inline void cpts_unregister(struct cpts *cpts)
{
}
+
+static inline void cpts_rx_enable(struct cpts *cpts, int enable)
+{
+}
+
+static inline bool cpts_is_rx_enabled(struct cpts *cpts)
+{
+ return false;
+}
+
+static inline void cpts_tx_enable(struct cpts *cpts, int enable)
+{
+}
+
+static inline bool cpts_is_tx_enabled(struct cpts *cpts)
+{
+ return false;
+}
#endif
--
2.10.1
^ permalink raw reply related
* [PATCH v5 02/13] net: ethernet: ti: allow cpts to be built separately
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
TI CPTS IP is used as part of TI OMAP CPSW driver, but it's also
present as part of NETCP on TI Keystone 2 SoCs. So, It's required
to enable build of CPTS for both this drivers and this can be
achieved by allowing CPTS to be built separately.
Hence, allow cpts to be built separately and convert it to be
a module as both CPSW and NETCP drives can be built as modules.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
drivers/net/ethernet/ti/Kconfig | 2 +-
drivers/net/ethernet/ti/Makefile | 3 ++-
drivers/net/ethernet/ti/cpsw.c | 22 +++++++++++++++++-----
drivers/net/ethernet/ti/cpts.c | 16 ++++++++--------
drivers/net/ethernet/ti/cpts.h | 18 ++++++++++++++----
5 files changed, 42 insertions(+), 19 deletions(-)
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 9904d74..ff7f518 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -74,7 +74,7 @@ config TI_CPSW
will be called cpsw.
config TI_CPTS
- bool "TI Common Platform Time Sync (CPTS) Support"
+ tristate "TI Common Platform Time Sync (CPTS) Support"
depends on TI_CPSW
select PTP_1588_CLOCK
---help---
diff --git a/drivers/net/ethernet/ti/Makefile b/drivers/net/ethernet/ti/Makefile
index d420d94..1e7c10b 100644
--- a/drivers/net/ethernet/ti/Makefile
+++ b/drivers/net/ethernet/ti/Makefile
@@ -12,8 +12,9 @@ obj-$(CONFIG_TI_DAVINCI_MDIO) += davinci_mdio.o
obj-$(CONFIG_TI_DAVINCI_CPDMA) += davinci_cpdma.o
obj-$(CONFIG_TI_CPSW_PHY_SEL) += cpsw-phy-sel.o
obj-$(CONFIG_TI_CPSW_ALE) += cpsw_ale.o
+obj-$(CONFIG_TI_CPTS) += cpts.o
obj-$(CONFIG_TI_CPSW) += ti_cpsw.o
-ti_cpsw-y := cpsw.o cpts.o
+ti_cpsw-y := cpsw.o
obj-$(CONFIG_TI_KEYSTONE_NETCP) += keystone_netcp.o
keystone_netcp-y := netcp_core.o
diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c
index f373a4b..8fdb274 100644
--- a/drivers/net/ethernet/ti/cpsw.c
+++ b/drivers/net/ethernet/ti/cpsw.c
@@ -1594,7 +1594,7 @@ static netdev_tx_t cpsw_ndo_start_xmit(struct sk_buff *skb,
return NETDEV_TX_BUSY;
}
-#ifdef CONFIG_TI_CPTS
+#if IS_ENABLED(CONFIG_TI_CPTS)
static void cpsw_hwtstamp_v1(struct cpsw_common *cpsw)
{
@@ -1742,7 +1742,16 @@ static int cpsw_hwtstamp_get(struct net_device *dev, struct ifreq *ifr)
return copy_to_user(ifr->ifr_data, &cfg, sizeof(cfg)) ? -EFAULT : 0;
}
+#else
+static int cpsw_hwtstamp_get(struct net_device *dev, struct ifreq *ifr)
+{
+ return -EOPNOTSUPP;
+}
+static int cpsw_hwtstamp_set(struct net_device *dev, struct ifreq *ifr)
+{
+ return -EOPNOTSUPP;
+}
#endif /*CONFIG_TI_CPTS*/
static int cpsw_ndo_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
@@ -1755,12 +1764,10 @@ static int cpsw_ndo_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
return -EINVAL;
switch (cmd) {
-#ifdef CONFIG_TI_CPTS
case SIOCSHWTSTAMP:
return cpsw_hwtstamp_set(dev, req);
case SIOCGHWTSTAMP:
return cpsw_hwtstamp_get(dev, req);
-#endif
}
if (!cpsw->slaves[slave_no].phy)
@@ -2100,10 +2107,10 @@ static void cpsw_set_msglevel(struct net_device *ndev, u32 value)
priv->msg_enable = value;
}
+#if IS_ENABLED(CONFIG_TI_CPTS)
static int cpsw_get_ts_info(struct net_device *ndev,
struct ethtool_ts_info *info)
{
-#ifdef CONFIG_TI_CPTS
struct cpsw_common *cpsw = ndev_to_cpsw(ndev);
info->so_timestamping =
@@ -2120,7 +2127,12 @@ static int cpsw_get_ts_info(struct net_device *ndev,
info->rx_filters =
(1 << HWTSTAMP_FILTER_NONE) |
(1 << HWTSTAMP_FILTER_PTP_V2_EVENT);
+ return 0;
+}
#else
+static int cpsw_get_ts_info(struct net_device *ndev,
+ struct ethtool_ts_info *info)
+{
info->so_timestamping =
SOF_TIMESTAMPING_TX_SOFTWARE |
SOF_TIMESTAMPING_RX_SOFTWARE |
@@ -2128,9 +2140,9 @@ static int cpsw_get_ts_info(struct net_device *ndev,
info->phc_index = -1;
info->tx_types = 0;
info->rx_filters = 0;
-#endif
return 0;
}
+#endif
static int cpsw_get_link_ksettings(struct net_device *ndev,
struct ethtool_link_ksettings *ecmd)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index a42c449..8cb0369 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -31,8 +31,6 @@
#include "cpts.h"
-#ifdef CONFIG_TI_CPTS
-
#define cpts_read32(c, r) readl_relaxed(&c->reg->r)
#define cpts_write32(c, v, r) writel_relaxed(v, &c->reg->r)
@@ -334,6 +332,7 @@ void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb)
memset(ssh, 0, sizeof(*ssh));
ssh->hwtstamp = ns_to_ktime(ns);
}
+EXPORT_SYMBOL_GPL(cpts_rx_timestamp);
void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
@@ -349,13 +348,11 @@ void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
ssh.hwtstamp = ns_to_ktime(ns);
skb_tstamp_tx(skb, &ssh);
}
-
-#endif /*CONFIG_TI_CPTS*/
+EXPORT_SYMBOL_GPL(cpts_tx_timestamp);
int cpts_register(struct device *dev, struct cpts *cpts,
u32 mult, u32 shift)
{
-#ifdef CONFIG_TI_CPTS
int err, i;
unsigned long flags;
@@ -391,18 +388,21 @@ int cpts_register(struct device *dev, struct cpts *cpts,
schedule_delayed_work(&cpts->overflow_work, CPTS_OVERFLOW_PERIOD);
cpts->phc_index = ptp_clock_index(cpts->clock);
-#endif
return 0;
}
+EXPORT_SYMBOL_GPL(cpts_register);
void cpts_unregister(struct cpts *cpts)
{
-#ifdef CONFIG_TI_CPTS
if (cpts->clock) {
ptp_clock_unregister(cpts->clock);
cancel_delayed_work_sync(&cpts->overflow_work);
}
if (cpts->refclk)
cpts_clk_release(cpts);
-#endif
}
+EXPORT_SYMBOL_GPL(cpts_unregister);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("TI CPTS driver");
+MODULE_AUTHOR("Richard Cochran <richardcochran@gmail.com>");
diff --git a/drivers/net/ethernet/ti/cpts.h b/drivers/net/ethernet/ti/cpts.h
index 69a46b9..416ba2c 100644
--- a/drivers/net/ethernet/ti/cpts.h
+++ b/drivers/net/ethernet/ti/cpts.h
@@ -111,7 +111,7 @@ struct cpts {
struct cpsw_cpts __iomem *reg;
int tx_enable;
int rx_enable;
-#ifdef CONFIG_TI_CPTS
+#if IS_ENABLED(CONFIG_TI_CPTS)
struct ptp_clock_info info;
struct ptp_clock *clock;
spinlock_t lock; /* protects time registers */
@@ -127,9 +127,11 @@ struct cpts {
#endif
};
-#ifdef CONFIG_TI_CPTS
+#if IS_ENABLED(CONFIG_TI_CPTS)
void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb);
void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb);
+int cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift);
+void cpts_unregister(struct cpts *cpts);
#else
static inline void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
@@ -137,9 +139,17 @@ static inline void cpts_rx_timestamp(struct cpts *cpts, struct sk_buff *skb)
static inline void cpts_tx_timestamp(struct cpts *cpts, struct sk_buff *skb)
{
}
+
+static inline int
+cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift)
+{
+ return 0;
+}
+
+static inline void cpts_unregister(struct cpts *cpts)
+{
+}
#endif
-int cpts_register(struct device *dev, struct cpts *cpts, u32 mult, u32 shift);
-void cpts_unregister(struct cpts *cpts);
#endif
--
2.10.1
^ permalink raw reply related
* [PATCH v5 01/13] net: ethernet: ti: cpts: switch to readl/writel_relaxed()
From: Grygorii Strashko @ 2016-12-07 0:00 UTC (permalink / raw)
To: David S. Miller, netdev, Mugunthan V N, Richard Cochran
Cc: Sekhar Nori, linux-kernel, linux-omap, devicetree,
Murali Karicheri, Wingman Kwok, Thomas Gleixner,
Grygorii Strashko
In-Reply-To: <20161207000045.28333-1-grygorii.strashko@ti.com>
Switch to readl/writel_relaxed() APIs, because this is recommended
API and the CPTS IP is reused on Keystone 2 SoCs
where LE/BE modes are supported.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
---
drivers/net/ethernet/ti/cpts.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/ti/cpts.c b/drivers/net/ethernet/ti/cpts.c
index 85a55b4..a42c449 100644
--- a/drivers/net/ethernet/ti/cpts.c
+++ b/drivers/net/ethernet/ti/cpts.c
@@ -33,8 +33,8 @@
#ifdef CONFIG_TI_CPTS
-#define cpts_read32(c, r) __raw_readl(&c->reg->r)
-#define cpts_write32(c, v, r) __raw_writel(v, &c->reg->r)
+#define cpts_read32(c, r) readl_relaxed(&c->reg->r)
+#define cpts_write32(c, v, r) writel_relaxed(v, &c->reg->r)
static int event_expired(struct cpts_event *event)
{
--
2.10.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox