* Re: [PATCH v3 4/4] phy: qcom-qmp: new qmp phy driver for qcom-chipsets
From: Stephen Boyd @ 2016-12-28 23:16 UTC (permalink / raw)
To: Vivek Gautam
Cc: robh+dt, kishon, linux-kernel, devicetree, mark.rutland,
srinivas.kandagatla, linux-arm-msm
In-Reply-To: <1482253431-23160-5-git-send-email-vivek.gautam@codeaurora.org>
On 12/20, Vivek Gautam wrote:
> Qualcomm SOCs have QMP phy controller that provides support
> to a number of controller, viz. PCIe, UFS, and USB.
> Add a new driver, based on generic phy framework, for this
> phy controller.
>
> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
>
> +
> +static struct phy *qcom_qmp_phy_xlate(struct device *dev,
> + struct of_phandle_args *args)
> +{
> + struct qcom_qmp_phy *qphy = dev_get_drvdata(dev);
> + int i;
> +
> + if (WARN_ON(args->args[0] >= qphy->cfg->nlanes))
> + return ERR_PTR(-ENODEV);
> +
> + for (i = 0; i < qphy->cfg->nlanes; i++)
> + /* phys[i]->index */
> + if (i == args->args[0])
> + return qphy->phys[i]->phy;
What's the loop for? If args->arg[0] < qphy->cfg->nlanes then we
should be able to directly index the qphy->phys array with that
number and return it.
> +
> + return ERR_PTR(-ENODEV);
> +}
> +
[...]
> +
> +/*
> + * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
> + * controls it. The <s>_pipe_clk coming out of the GCC is requested
> + * by the PHY driver for its operations.
> + * We register the <s>_pipe_clksrc here. The gcc driver takes care
> + * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
> + * Below picture shows this relationship.
> + *
> + * +--------------+
> + * | PHY block |<<---------------------------------------+
> + * | | |
> + * | +-------+ | +-----+ |
> + * I/P---^-->| PLL |--^--->pipe_clksrc--->| GCC |--->pipe_clk---+
> + * clk | +-------+ | +-----+
> + * +--------------+
There are mixed tabs and spaces in this diagram causing
confusion in my editor. Please make it only spaces so the picture
comes out correctly.
> + *
> + */
> +static int phy_pipe_clk_register(struct qcom_qmp_phy *qphy, int id)
> +{
> + char clk_name[MAX_PROP_NAME];
I'm not sure MAX_PROP_NAME is the same as some max clk name but
ok. We should be able to calculate that the maximum is length of
usb3_phy_pipe_clk_src for now though?
> + struct clk *clk;
> +
> + memset(&clk_name, 0, sizeof(clk_name));
> + switch (qphy->cfg->type) {
> + case PHY_TYPE_USB3:
> + snprintf(clk_name, MAX_PROP_NAME, "usb3_phy_pipe_clk_src");
> + break;
> + case PHY_TYPE_PCIE:
> + snprintf(clk_name, MAX_PROP_NAME, "pcie_%d_pipe_clk_src", id);
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /* controllers using QMP phys use 125MHz pipe clock interface */
> + clk = clk_register_fixed_rate(qphy->dev, clk_name, NULL, 0, 125000000);
I was hoping you would be able to calculate the actual output
rate by reading hardware. This is ok too though. Just please use
clk_hw_register_fixed_rate() instead. And you'll probably need
some sort of devm() usage here to handle probe failure, so I
would probably roll my own and allocate a fixed_rate clk
structure and set the rate/name directly and then call
devm_clk_hw_register().
> +
> + return PTR_ERR_OR_ZERO(clk);
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH v2 0/2] add clk-hi3660
From: Zhangfei Gao @ 2016-12-29 2:33 UTC (permalink / raw)
To: Stephen Boyd, Rob Herring, Arnd Bergmann,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A, guodong Xu
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Zhangfei Gao
Address comments from Rob and Stephen.
Rebase to 4.10-rc1
Zhangfei Gao (2):
dt-bindings: Document the hi3660 clock bindings
clk: hisilicon: Add clock driver for hi3660 SoC
.../devicetree/bindings/clock/hi3660-clock.txt | 42 ++
drivers/clk/hisilicon/Kconfig | 7 +
drivers/clk/hisilicon/Makefile | 1 +
drivers/clk/hisilicon/clk-hi3660.c | 592 +++++++++++++++++++++
include/dt-bindings/clock/hi3660-clock.h | 194 +++++++
5 files changed, 836 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/hi3660-clock.txt
create mode 100644 drivers/clk/hisilicon/clk-hi3660.c
create mode 100644 include/dt-bindings/clock/hi3660-clock.h
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH v2 1/2] dt-bindings: Document the hi3660 clock bindings
From: Zhangfei Gao @ 2016-12-29 2:33 UTC (permalink / raw)
To: Stephen Boyd, Rob Herring, Arnd Bergmann,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A, guodong Xu
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Zhangfei Gao
In-Reply-To: <1482978805-6981-1-git-send-email-zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Add DT bindings documentation for hi3660 SoC clock.
Signed-off-by: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
.../devicetree/bindings/clock/hi3660-clock.txt | 42 ++++++++++++++++++++++
1 file changed, 42 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/hi3660-clock.txt
diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt
new file mode 100644
index 0000000..cc9b86c
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt
@@ -0,0 +1,42 @@
+* Hisilicon Hi3660 Clock Controller
+
+The Hi3660 clock controller generates and supplies clock to various
+controllers within the Hi3660 SoC.
+
+Required Properties:
+
+- compatible: the compatible should be one of the following strings to
+ indicate the clock controller functionality.
+
+ - "hisilicon,hi3660-crgctrl"
+ - "hisilicon,hi3660-pctrl"
+ - "hisilicon,hi3660-pmuctrl"
+ - "hisilicon,hi3660-sctrl"
+ - "hisilicon,hi3660-iomcu"
+
+- reg: physical base address of the controller and length of memory mapped
+ region.
+
+- #clock-cells: should be 1.
+
+Each clock is assigned an identifier and client nodes use this identifier
+to specify the clock which they consume.
+
+All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>.
+
+Examples:
+ crg_ctrl: clock-controller@fff35000 {
+ compatible = "hisilicon,hi3660-crgctrl", "syscon";
+ reg = <0x0 0xfff35000 0x0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ uart0: serial@fdf02000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0xfdf02000 0x0 0x1000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>,
+ <&crg_ctrl HI3660_PCLK>;
+ clock-names = "uartclk", "apb_pclk";
+ status = "disabled";
+ };
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v2 2/2] clk: hisilicon: Add clock driver for hi3660 SoC
From: Zhangfei Gao @ 2016-12-29 2:33 UTC (permalink / raw)
To: Stephen Boyd, Rob Herring, Arnd Bergmann,
haojian.zhuang-QSEj5FYQhm4dnm+yROfE0A, guodong Xu
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, Zhangfei Gao
In-Reply-To: <1482978805-6981-1-git-send-email-zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Add clock drivers for hi3660 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
Signed-off-by: Zhangfei Gao <zhangfei.gao-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
drivers/clk/hisilicon/Kconfig | 7 +
drivers/clk/hisilicon/Makefile | 1 +
drivers/clk/hisilicon/clk-hi3660.c | 592 +++++++++++++++++++++++++++++++
include/dt-bindings/clock/hi3660-clock.h | 194 ++++++++++
4 files changed, 794 insertions(+)
create mode 100644 drivers/clk/hisilicon/clk-hi3660.c
create mode 100644 include/dt-bindings/clock/hi3660-clock.h
diff --git a/drivers/clk/hisilicon/Kconfig b/drivers/clk/hisilicon/Kconfig
index cbed660..7098bfd 100644
--- a/drivers/clk/hisilicon/Kconfig
+++ b/drivers/clk/hisilicon/Kconfig
@@ -14,6 +14,13 @@ config COMMON_CLK_HI3519
help
Build the clock driver for hi3519.
+config COMMON_CLK_HI3660
+ bool "Hi3660 Clock Driver"
+ depends on ARCH_HISI || COMPILE_TEST
+ default ARCH_HISI
+ help
+ Build the clock driver for hi3660.
+
config COMMON_CLK_HI3798CV200
tristate "Hi3798CV200 Clock Driver"
depends on ARCH_HISI || COMPILE_TEST
diff --git a/drivers/clk/hisilicon/Makefile b/drivers/clk/hisilicon/Makefile
index 4eec5e5..1e4c3dd 100644
--- a/drivers/clk/hisilicon/Makefile
+++ b/drivers/clk/hisilicon/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_ARCH_HIP04) += clk-hip04.o
obj-$(CONFIG_ARCH_HIX5HD2) += clk-hix5hd2.o
obj-$(CONFIG_COMMON_CLK_HI3516CV300) += crg-hi3516cv300.o
obj-$(CONFIG_COMMON_CLK_HI3519) += clk-hi3519.o
+obj-$(CONFIG_COMMON_CLK_HI3660) += clk-hi3660.o
obj-$(CONFIG_COMMON_CLK_HI3798CV200) += crg-hi3798cv200.o
obj-$(CONFIG_COMMON_CLK_HI6220) += clk-hi6220.o
obj-$(CONFIG_RESET_HISI) += reset.o
diff --git a/drivers/clk/hisilicon/clk-hi3660.c b/drivers/clk/hisilicon/clk-hi3660.c
new file mode 100644
index 0000000..4e752c6
--- /dev/null
+++ b/drivers/clk/hisilicon/clk-hi3660.c
@@ -0,0 +1,592 @@
+/*
+ * Copyright (c) 2016-2017 Linaro Ltd.
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <dt-bindings/clock/hi3660-clock.h>
+#include <linux/clk-provider.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include "clk.h"
+
+enum hi3660_clk_type {
+ HI3660_CRGCTRL = 1,
+ HI3660_PCTRL,
+ HI3660_PMUCTRL,
+ HI3660_SCTRL,
+ HI3660_IOMCU,
+};
+
+static const struct hisi_fixed_rate_clock hi3660_fixed_rate_clks[] = {
+ { HI3660_CLKIN_SYS, "clkin_sys", NULL, 0, 19200000, },
+ { HI3660_CLKIN_REF, "clkin_ref", NULL, 0, 32764, },
+ { HI3660_CLK_FLL_SRC, "clk_fll_src", NULL, 0, 128000000, },
+ { HI3660_CLK_PPLL0, "clk_ppll0", NULL, 0, 1600000000, },
+ { HI3660_CLK_PPLL1, "clk_ppll1", NULL, 0, 1866000000, },
+ { HI3660_CLK_PPLL2, "clk_ppll2", NULL, 0, 960000000, },
+ { HI3660_CLK_PPLL3, "clk_ppll3", NULL, 0, 1290000000, },
+ { HI3660_CLK_SCPLL, "clk_scpll", NULL, 0, 245760000, },
+ { HI3660_PCLK, "pclk", NULL, 0, 20000000, },
+ { HI3660_CLK_UART0_DBG, "clk_uart0_dbg", NULL, 0, 19200000, },
+ { HI3660_CLK_UART6, "clk_uart6", NULL, 0, 19200000, },
+ { HI3660_OSC32K, "osc32k", NULL, 0, 32764, },
+ { HI3660_OSC19M, "osc19m", NULL, 0, 19200000, },
+ { HI3660_CLK_480M, "clk_480m", NULL, 0, 480000000, },
+ { HI3660_CLK_INV, "clk_inv", NULL, 0, 10000000, },
+};
+
+/* crgctrl */
+static const struct hisi_fixed_factor_clock hi3660_crg_fixed_factor_clks[] = {
+ { HI3660_FACTOR_UART3, "clk_factor_uart3", "iomcu_peri0", 1, 8, 0, },
+ { HI3660_CLK_FACTOR_MMC, "clk_factor_mmc", "clkin_sys", 1, 6, 0, },
+ { HI3660_CLK_GATE_I2C0, "clk_gate_i2c0", "clk_i2c0_iomcu", 1, 4, 0, },
+ { HI3660_CLK_GATE_I2C1, "clk_gate_i2c1", "clk_i2c1_iomcu", 1, 4, 0, },
+ { HI3660_CLK_GATE_I2C2, "clk_gate_i2c2", "clk_i2c2_iomcu", 1, 4, 0, },
+ { HI3660_CLK_GATE_I2C6, "clk_gate_i2c6", "clk_i2c6_iomcu", 1, 4, 0, },
+ { HI3660_CLK_DIV_SYSBUS, "clk_div_sysbus", "clk_mux_sysbus", 1, 7, 0, },
+ { HI3660_CLK_DIV_320M, "clk_div_320m", "clk_320m_pll_gt", 1, 5, 0, },
+ { HI3660_CLK_DIV_A53, "clk_div_a53hpm", "clk_a53hpm_andgt", 1, 2, 0, },
+ { HI3660_CLK_GATE_SPI0, "clk_gate_spi0", "clk_ppll0", 1, 8, 0, },
+ { HI3660_CLK_GATE_SPI2, "clk_gate_spi2", "clk_ppll0", 1, 8, 0, },
+ { HI3660_PCIEPHY_REF, "clk_pciephy_ref", "clk_div_pciephy", 1, 1, 0, },
+ { HI3660_CLK_ABB_USB, "clk_abb_usb", "clk_gate_usb_tcxo_en", 1, 1, 0 },
+};
+
+static const struct hisi_gate_clock hi3660_crgctrl_gate_sep_clks[] = {
+ { HI3660_HCLK_GATE_SDIO0, "hclk_gate_sdio0", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0x0, 21, 0, },
+ { HI3660_HCLK_GATE_SD, "hclk_gate_sd", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0x0, 30, 0, },
+ { HI3660_CLK_GATE_AOMM, "clk_gate_aomm", "clk_div_aomm",
+ CLK_SET_RATE_PARENT, 0x0, 31, 0, },
+ { HI3660_PCLK_GPIO0, "pclk_gpio0", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 0, 0, },
+ { HI3660_PCLK_GPIO1, "pclk_gpio1", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 1, 0, },
+ { HI3660_PCLK_GPIO2, "pclk_gpio2", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 2, 0, },
+ { HI3660_PCLK_GPIO3, "pclk_gpio3", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 3, 0, },
+ { HI3660_PCLK_GPIO4, "pclk_gpio4", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 4, 0, },
+ { HI3660_PCLK_GPIO5, "pclk_gpio5", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 5, 0, },
+ { HI3660_PCLK_GPIO6, "pclk_gpio6", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 6, 0, },
+ { HI3660_PCLK_GPIO7, "pclk_gpio7", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 7, 0, },
+ { HI3660_PCLK_GPIO8, "pclk_gpio8", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 8, 0, },
+ { HI3660_PCLK_GPIO9, "pclk_gpio9", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 9, 0, },
+ { HI3660_PCLK_GPIO10, "pclk_gpio10", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 10, 0, },
+ { HI3660_PCLK_GPIO11, "pclk_gpio11", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 11, 0, },
+ { HI3660_PCLK_GPIO12, "pclk_gpio12", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 12, 0, },
+ { HI3660_PCLK_GPIO13, "pclk_gpio13", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 13, 0, },
+ { HI3660_PCLK_GPIO14, "pclk_gpio14", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 14, 0, },
+ { HI3660_PCLK_GPIO15, "pclk_gpio15", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 15, 0, },
+ { HI3660_PCLK_GPIO16, "pclk_gpio16", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 16, 0, },
+ { HI3660_PCLK_GPIO17, "pclk_gpio17", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 17, 0, },
+ { HI3660_PCLK_GPIO18, "pclk_gpio18", "clk_div_ioperi",
+ CLK_SET_RATE_PARENT, 0x10, 18, 0, },
+ { HI3660_PCLK_GPIO19, "pclk_gpio19", "clk_div_ioperi",
+ CLK_SET_RATE_PARENT, 0x10, 19, 0, },
+ { HI3660_PCLK_GPIO20, "pclk_gpio20", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 20, 0, },
+ { HI3660_PCLK_GPIO21, "pclk_gpio21", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x10, 21, 0, },
+ { HI3660_CLK_GATE_SPI3, "clk_gate_spi3", "clk_div_ioperi",
+ CLK_SET_RATE_PARENT, 0x10, 30, 0, },
+ { HI3660_CLK_GATE_I2C7, "clk_gate_i2c7", "clk_mux_i2c",
+ CLK_SET_RATE_PARENT, 0x10, 31, 0, },
+ { HI3660_CLK_GATE_I2C3, "clk_gate_i2c3", "clk_mux_i2c",
+ CLK_SET_RATE_PARENT, 0x20, 7, 0, },
+ { HI3660_CLK_GATE_SPI1, "clk_gate_spi1", "clk_mux_spi",
+ CLK_SET_RATE_PARENT, 0x20, 9, 0, },
+ { HI3660_CLK_GATE_UART1, "clk_gate_uart1", "clk_mux_uarth",
+ CLK_SET_RATE_PARENT, 0x20, 11, 0, },
+ { HI3660_CLK_GATE_UART2, "clk_gate_uart2", "clk_mux_uart1",
+ CLK_SET_RATE_PARENT, 0x20, 12, 0, },
+ { HI3660_CLK_GATE_UART4, "clk_gate_uart4", "clk_mux_uarth",
+ CLK_SET_RATE_PARENT, 0x20, 14, 0, },
+ { HI3660_CLK_GATE_UART5, "clk_gate_uart5", "clk_mux_uart1",
+ CLK_SET_RATE_PARENT, 0x20, 15, 0, },
+ { HI3660_CLK_GATE_I2C4, "clk_gate_i2c4", "clk_mux_i2c",
+ CLK_SET_RATE_PARENT, 0x20, 27, 0, },
+ { HI3660_CLK_GATE_DMAC, "clk_gate_dmac", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0x30, 1, 0, },
+ { HI3660_PCLK_GATE_DSS, "pclk_gate_dss", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x30, 12, 0, },
+ { HI3660_ACLK_GATE_DSS, "aclk_gate_dss", "clk_gate_vivobus",
+ CLK_SET_RATE_PARENT, 0x30, 13, 0, },
+ { HI3660_CLK_GATE_LDI1, "clk_gate_ldi1", "clk_div_ldi1",
+ CLK_SET_RATE_PARENT, 0x30, 14, 0, },
+ { HI3660_CLK_GATE_LDI0, "clk_gate_ldi0", "clk_div_ldi0",
+ CLK_SET_RATE_PARENT, 0x30, 15, 0, },
+ { HI3660_CLK_GATE_VIVOBUS, "clk_gate_vivobus", "clk_div_vivobus",
+ CLK_SET_RATE_PARENT, 0x30, 16, 0, },
+ { HI3660_CLK_GATE_EDC0, "clk_gate_edc0", "clk_div_edc0",
+ CLK_SET_RATE_PARENT, 0x30, 17, 0, },
+ { HI3660_CLK_GATE_TXDPHY0_CFG, "clk_gate_txdphy0_cfg", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x30, 28, 0, },
+ { HI3660_CLK_GATE_TXDPHY0_REF, "clk_gate_txdphy0_ref", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x30, 29, 0, },
+ { HI3660_CLK_GATE_TXDPHY1_CFG, "clk_gate_txdphy1_cfg", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x30, 30, 0, },
+ { HI3660_CLK_GATE_TXDPHY1_REF, "clk_gate_txdphy1_ref", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x30, 31, 0, },
+ { HI3660_ACLK_GATE_USB3OTG, "aclk_gate_usb3otg", "clk_div_mmc0bus",
+ CLK_SET_RATE_PARENT, 0x40, 1, 0, },
+ { HI3660_CLK_GATE_SPI4, "clk_gate_spi4", "clk_mux_spi",
+ CLK_SET_RATE_PARENT, 0x40, 4, 0, },
+ { HI3660_CLK_GATE_SD, "clk_gate_sd", "clk_mux_sd_sys",
+ CLK_SET_RATE_PARENT, 0x40, 17, 0, },
+ { HI3660_CLK_GATE_SDIO0, "clk_gate_sdio0", "clk_mux_sdio_sys",
+ CLK_SET_RATE_PARENT, 0x40, 19, 0, },
+ { HI3660_CLK_GATE_UFS_SUBSYS, "clk_gate_ufs_subsys", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0x50, 21, 0, },
+ { HI3660_PCLK_GATE_DSI0, "pclk_gate_dsi0", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x50, 28, 0, },
+ { HI3660_PCLK_GATE_DSI1, "pclk_gate_dsi1", "clk_div_cfgbus",
+ CLK_SET_RATE_PARENT, 0x50, 29, 0, },
+ { HI3660_ACLK_GATE_PCIE, "aclk_gate_pcie", "clk_div_mmc1bus",
+ CLK_SET_RATE_PARENT, 0x420, 5, 0, },
+ { HI3660_PCLK_GATE_PCIE_SYS, "pclk_gate_pcie_sys", "clk_div_mmc1bus",
+ CLK_SET_RATE_PARENT, 0x420, 7, 0, },
+ { HI3660_CLK_GATE_PCIEAUX, "clk_gate_pcieaux", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x420, 8, 0, },
+ { HI3660_PCLK_GATE_PCIE_PHY, "pclk_gate_pcie_phy", "clk_div_mmc1bus",
+ CLK_SET_RATE_PARENT, 0x420, 9, 0, },
+};
+
+static const struct hisi_gate_clock hi3660_crgctrl_gate_clks[] = {
+ { HI3660_CLK_ANDGT_LDI0, "clk_andgt_ldi0", "clk_mux_ldi0",
+ CLK_SET_RATE_PARENT, 0xf0, 6, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_LDI1, "clk_andgt_ldi1", "clk_mux_ldi1",
+ CLK_SET_RATE_PARENT, 0xf0, 7, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_EDC0, "clk_andgt_edc0", "clk_mux_edc0",
+ CLK_SET_RATE_PARENT, 0xf0, 8, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_GATE_UFSPHY_GT, "clk_gate_ufsphy_gt", "clk_div_ufsperi",
+ CLK_SET_RATE_PARENT, 0xf4, 1, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_MMC, "clk_andgt_mmc", "clk_mux_mmc_pll",
+ CLK_SET_RATE_PARENT, 0xf4, 2, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_SD, "clk_andgt_sd", "clk_mux_sd_pll",
+ CLK_SET_RATE_PARENT, 0xf4, 3, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_A53HPM_ANDGT, "clk_a53hpm_andgt", "clk_mux_a53hpm",
+ CLK_SET_RATE_PARENT, 0xf4, 7, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_SDIO, "clk_andgt_sdio", "clk_mux_sdio_pll",
+ CLK_SET_RATE_PARENT, 0xf4, 8, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_UART0, "clk_andgt_uart0", "clk_div_320m",
+ CLK_SET_RATE_PARENT, 0xf4, 9, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_UART1, "clk_andgt_uart1", "clk_div_320m",
+ CLK_SET_RATE_PARENT, 0xf4, 10, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_UARTH, "clk_andgt_uarth", "clk_div_320m",
+ CLK_SET_RATE_PARENT, 0xf4, 11, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_ANDGT_SPI, "clk_andgt_spi", "clk_div_320m",
+ CLK_SET_RATE_PARENT, 0xf4, 13, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_VIVOBUS_ANDGT, "clk_vivobus_andgt", "clk_mux_vivobus",
+ CLK_SET_RATE_PARENT, 0xf8, 1, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_AOMM_ANDGT, "clk_aomm_andgt", "clk_ppll2",
+ CLK_SET_RATE_PARENT, 0xf8, 3, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_320M_PLL_GT, "clk_320m_pll_gt", "clk_mux_320m",
+ CLK_SET_RATE_PARENT, 0xf8, 10, 0, },
+ { HI3660_AUTODIV_EMMC0BUS, "autodiv_emmc0bus", "autodiv_sysbus",
+ CLK_SET_RATE_PARENT, 0x404, 1, CLK_GATE_HIWORD_MASK, },
+ { HI3660_AUTODIV_SYSBUS, "autodiv_sysbus", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0x404, 5, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_GATE_UFSPHY_CFG, "clk_gate_ufsphy_cfg",
+ "clk_div_ufsphy_cfg", CLK_SET_RATE_PARENT, 0x420, 12, 0, },
+ { HI3660_CLK_GATE_UFSIO_REF, "clk_gate_ufsio_ref",
+ "clk_gate_ufs_tcxo_en", CLK_SET_RATE_PARENT, 0x420, 14, 0, },
+};
+
+static const char *const
+clk_mux_sdio_sys_p[] = {"clk_factor_mmc", "clk_div_sdio",};
+static const char *const
+clk_mux_sd_sys_p[] = {"clk_factor_mmc", "clk_div_sd",};
+static const char *const
+clk_mux_pll_p[] = {"clk_ppll0", "clk_ppll1", "clk_ppll2", "clk_ppll2",};
+static const char *const
+clk_mux_pll0123_p[] = {"clk_ppll0", "clk_ppll1", "clk_ppll2", "clk_ppll3",};
+static const char *const
+clk_mux_edc0_p[] = {"clk_inv", "clk_ppll0", "clk_ppll1", "clk_inv",
+ "clk_ppll2", "clk_inv", "clk_inv", "clk_inv",
+ "clk_ppll3", "clk_inv", "clk_inv", "clk_inv",
+ "clk_inv", "clk_inv", "clk_inv", "clk_inv",};
+static const char *const
+clk_mux_ldi0_p[] = {"clk_inv", "clk_ppll0", "clk_ppll2", "clk_inv",
+ "clk_ppll1", "clk_inv", "clk_inv", "clk_inv",
+ "clk_ppll3", "clk_inv", "clk_inv", "clk_inv",
+ "clk_inv", "clk_inv", "clk_inv", "clk_inv",};
+static const char *const
+clk_mux_uart0_p[] = {"clkin_sys", "clk_div_uart0",};
+static const char *const
+clk_mux_uart1_p[] = {"clkin_sys", "clk_div_uart1",};
+static const char *const
+clk_mux_uarth_p[] = {"clkin_sys", "clk_div_uarth",};
+static const char *const
+clk_mux_pll02p[] = {"clk_ppll0", "clk_ppll2",};
+static const char *const
+clk_mux_ioperi_p[] = {"clk_div_320m", "clk_div_a53hpm",};
+static const char *const
+clk_mux_spi_p[] = {"clkin_sys", "clk_div_spi",};
+static const char *const
+clk_mux_i2c_p[] = {"clkin_sys", "clk_div_i2c",};
+
+static const struct hisi_mux_clock hi3660_crgctrl_mux_clks[] = {
+ { HI3660_CLK_MUX_SYSBUS, "clk_mux_sysbus", clk_mux_sdio_sys_p,
+ ARRAY_SIZE(clk_mux_sdio_sys_p), CLK_SET_RATE_PARENT, 0xac, 0, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_UART0, "clk_mux_uart0", clk_mux_uart0_p,
+ ARRAY_SIZE(clk_mux_uart0_p), CLK_SET_RATE_PARENT, 0xac, 2, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_UART1, "clk_mux_uart1", clk_mux_uart1_p,
+ ARRAY_SIZE(clk_mux_uart1_p), CLK_SET_RATE_PARENT, 0xac, 3, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_UARTH, "clk_mux_uarth", clk_mux_uarth_p,
+ ARRAY_SIZE(clk_mux_uarth_p), CLK_SET_RATE_PARENT, 0xac, 4, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_SPI, "clk_mux_spi", clk_mux_spi_p,
+ ARRAY_SIZE(clk_mux_spi_p), CLK_SET_RATE_PARENT, 0xac, 8, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_I2C, "clk_mux_i2c", clk_mux_i2c_p,
+ ARRAY_SIZE(clk_mux_i2c_p), CLK_SET_RATE_PARENT, 0xac, 13, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_MMC_PLL, "clk_mux_mmc_pll", clk_mux_pll02p,
+ ARRAY_SIZE(clk_mux_pll02p), CLK_SET_RATE_PARENT, 0xb4, 0, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_LDI1, "clk_mux_ldi1", clk_mux_ldi0_p,
+ ARRAY_SIZE(clk_mux_ldi0_p), CLK_SET_RATE_PARENT, 0xb4, 8, 4,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_LDI0, "clk_mux_ldi0", clk_mux_ldi0_p,
+ ARRAY_SIZE(clk_mux_ldi0_p), CLK_SET_RATE_PARENT, 0xb4, 12, 4,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_SD_PLL, "clk_mux_sd_pll", clk_mux_pll_p,
+ ARRAY_SIZE(clk_mux_pll_p), CLK_SET_RATE_PARENT, 0xb8, 4, 2,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_SD_SYS, "clk_mux_sd_sys", clk_mux_sd_sys_p,
+ ARRAY_SIZE(clk_mux_sd_sys_p), CLK_SET_RATE_PARENT, 0xb8, 6, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_EDC0, "clk_mux_edc0", clk_mux_edc0_p,
+ ARRAY_SIZE(clk_mux_edc0_p), CLK_SET_RATE_PARENT, 0xbc, 6, 4,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_SDIO_SYS, "clk_mux_sdio_sys", clk_mux_sdio_sys_p,
+ ARRAY_SIZE(clk_mux_sdio_sys_p), CLK_SET_RATE_PARENT, 0xc0, 6, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_SDIO_PLL, "clk_mux_sdio_pll", clk_mux_pll_p,
+ ARRAY_SIZE(clk_mux_pll_p), CLK_SET_RATE_PARENT, 0xc0, 4, 2,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_VIVOBUS, "clk_mux_vivobus", clk_mux_pll0123_p,
+ ARRAY_SIZE(clk_mux_pll0123_p), CLK_SET_RATE_PARENT, 0xd0, 12, 2,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_A53HPM, "clk_mux_a53hpm", clk_mux_pll02p,
+ ARRAY_SIZE(clk_mux_pll02p), CLK_SET_RATE_PARENT, 0xd4, 9, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_320M, "clk_mux_320m", clk_mux_pll02p,
+ ARRAY_SIZE(clk_mux_pll02p), CLK_SET_RATE_PARENT, 0x100, 0, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_MUX_IOPERI, "clk_mux_ioperi", clk_mux_ioperi_p,
+ ARRAY_SIZE(clk_mux_ioperi_p), CLK_SET_RATE_PARENT, 0x108, 10, 1,
+ CLK_MUX_HIWORD_MASK, },
+};
+
+static const struct hisi_divider_clock hi3660_crgctrl_divider_clks[] = {
+ { HI3660_CLK_DIV_UART0, "clk_div_uart0", "clk_andgt_uart0",
+ CLK_SET_RATE_PARENT, 0xb0, 4, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_UART1, "clk_div_uart1", "clk_andgt_uart1",
+ CLK_SET_RATE_PARENT, 0xb0, 8, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_UARTH, "clk_div_uarth", "clk_andgt_uarth",
+ CLK_SET_RATE_PARENT, 0xb0, 12, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_MMC, "clk_div_mmc", "clk_andgt_mmc",
+ CLK_SET_RATE_PARENT, 0xb4, 3, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_SD, "clk_div_sd", "clk_andgt_sd",
+ CLK_SET_RATE_PARENT, 0xb8, 0, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_EDC0, "clk_div_edc0", "clk_andgt_edc0",
+ CLK_SET_RATE_PARENT, 0xbc, 0, 6, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_LDI0, "clk_div_ldi0", "clk_andgt_ldi0",
+ CLK_SET_RATE_PARENT, 0xbc, 10, 6, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_SDIO, "clk_div_sdio", "clk_andgt_sdio",
+ CLK_SET_RATE_PARENT, 0xc0, 0, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_LDI1, "clk_div_ldi1", "clk_andgt_ldi1",
+ CLK_SET_RATE_PARENT, 0xc0, 8, 6, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_SPI, "clk_div_spi", "clk_andgt_spi",
+ CLK_SET_RATE_PARENT, 0xc4, 12, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_VIVOBUS, "clk_div_vivobus", "clk_vivobus_andgt",
+ CLK_SET_RATE_PARENT, 0xd0, 7, 5, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_I2C, "clk_div_i2c", "clk_div_320m",
+ CLK_SET_RATE_PARENT, 0xe8, 4, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_UFSPHY, "clk_div_ufsphy_cfg", "clk_gate_ufsphy_gt",
+ CLK_SET_RATE_PARENT, 0xe8, 9, 2, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_CFGBUS, "clk_div_cfgbus", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0xec, 0, 2, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_MMC0BUS, "clk_div_mmc0bus", "autodiv_emmc0bus",
+ CLK_SET_RATE_PARENT, 0xec, 2, 1, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_MMC1BUS, "clk_div_mmc1bus", "clk_div_sysbus",
+ CLK_SET_RATE_PARENT, 0xec, 3, 1, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_UFSPERI, "clk_div_ufsperi", "clk_gate_ufs_subsys",
+ CLK_SET_RATE_PARENT, 0xec, 14, 1, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_AOMM, "clk_div_aomm", "clk_aomm_andgt",
+ CLK_SET_RATE_PARENT, 0x100, 7, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_IOPERI, "clk_div_ioperi", "clk_mux_ioperi",
+ CLK_SET_RATE_PARENT, 0x108, 11, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+};
+
+/* clk_pmuctrl */
+/* pmu register need shift 2 bits */
+static const struct hisi_gate_clock hi3660_pmu_gate_clks[] = {
+ { HI3660_GATE_ABB_192, "clk_gate_abb_192", "clkin_sys",
+ CLK_SET_RATE_PARENT, (0x10a << 2), 3, 0, },
+};
+
+/* clk_pctrl */
+static const struct hisi_gate_clock hi3660_pctrl_gate_clks[] = {
+ { HI3660_GATE_UFS_TCXO_EN, "clk_gate_ufs_tcxo_en",
+ "clk_gate_abb_192", CLK_SET_RATE_PARENT, 0x10, 0,
+ CLK_GATE_HIWORD_MASK, },
+ { HI3660_GATE_USB_TCXO_EN, "clk_gate_usb_tcxo_en", "clk_gate_abb_192",
+ CLK_SET_RATE_PARENT, 0x10, 1, CLK_GATE_HIWORD_MASK, },
+};
+
+/* clk_sctrl */
+static const struct hisi_gate_clock hi3660_sctrl_gate_sep_clks[] = {
+ { HI3660_PCLK_AO_GPIO0, "pclk_ao_gpio0", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 11, 0, },
+ { HI3660_PCLK_AO_GPIO1, "pclk_ao_gpio1", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 12, 0, },
+ { HI3660_PCLK_AO_GPIO2, "pclk_ao_gpio2", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 13, 0, },
+ { HI3660_PCLK_AO_GPIO3, "pclk_ao_gpio3", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 14, 0, },
+ { HI3660_PCLK_AO_GPIO4, "pclk_ao_gpio4", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 21, 0, },
+ { HI3660_PCLK_AO_GPIO5, "pclk_ao_gpio5", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 22, 0, },
+ { HI3660_PCLK_AO_GPIO6, "pclk_ao_gpio6", "clk_div_aobus",
+ CLK_SET_RATE_PARENT, 0x160, 25, 0, },
+ { HI3660_PCLK_GATE_MMBUF, "pclk_gate_mmbuf", "pclk_div_mmbuf",
+ CLK_SET_RATE_PARENT, 0x170, 23, 0, },
+ { HI3660_CLK_GATE_DSS_AXI_MM, "clk_gate_dss_axi_mm", "aclk_mux_mmbuf",
+ CLK_SET_RATE_PARENT, 0x170, 24, 0, },
+};
+
+static const struct hisi_gate_clock hi3660_sctrl_gate_clks[] = {
+ { HI3660_PCLK_MMBUF_ANDGT, "pclk_mmbuf_andgt", "clk_sw_mmbuf",
+ CLK_SET_RATE_PARENT, 0x258, 7, CLK_GATE_HIWORD_MASK, },
+ { HI3660_CLK_MMBUF_PLL_ANDGT, "clk_mmbuf_pll_andgt", "clk_ppll0",
+ CLK_SET_RATE_PARENT, 0x260, 11, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_FLL_MMBUF_ANDGT, "clk_fll_mmbuf_andgt", "clk_fll_src",
+ CLK_SET_RATE_PARENT, 0x260, 12, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_SYS_MMBUF_ANDGT, "clk_sys_mmbuf_andgt", "clkin_sys",
+ CLK_SET_RATE_PARENT, 0x260, 13, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_GATE_PCIEPHY_GT, "clk_gate_pciephy_gt", "clk_ppll0",
+ CLK_SET_RATE_PARENT, 0x268, 11, CLK_DIVIDER_HIWORD_MASK, 0, },
+};
+
+static const char *const
+aclk_mux_mmbuf_p[] = {"aclk_div_mmbuf", "clk_gate_aomm",};
+static const char *const
+clk_sw_mmbuf_p[] = {"clk_sys_mmbuf_andgt", "clk_fll_mmbuf_andgt",
+ "aclk_mux_mmbuf", "aclk_mux_mmbuf"};
+
+static const struct hisi_mux_clock hi3660_sctrl_mux_clks[] = {
+ { HI3660_ACLK_MUX_MMBUF, "aclk_mux_mmbuf", aclk_mux_mmbuf_p,
+ ARRAY_SIZE(aclk_mux_mmbuf_p), CLK_SET_RATE_PARENT, 0x250, 12, 1,
+ CLK_MUX_HIWORD_MASK, },
+ { HI3660_CLK_SW_MMBUF, "clk_sw_mmbuf", clk_sw_mmbuf_p,
+ ARRAY_SIZE(clk_sw_mmbuf_p), CLK_SET_RATE_PARENT, 0x258, 8, 2,
+ CLK_MUX_HIWORD_MASK, },
+};
+
+static const struct hisi_divider_clock hi3660_sctrl_divider_clks[] = {
+ { HI3660_CLK_DIV_AOBUS, "clk_div_aobus", "clk_ppll0",
+ CLK_SET_RATE_PARENT, 0x254, 0, 6, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_PCLK_DIV_MMBUF, "pclk_div_mmbuf", "pclk_mmbuf_andgt",
+ CLK_SET_RATE_PARENT, 0x258, 10, 2, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_ACLK_DIV_MMBUF, "aclk_div_mmbuf", "clk_mmbuf_pll_andgt",
+ CLK_SET_RATE_PARENT, 0x258, 12, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+ { HI3660_CLK_DIV_PCIEPHY, "clk_div_pciephy", "clk_gate_pciephy_gt",
+ CLK_SET_RATE_PARENT, 0x268, 12, 4, CLK_DIVIDER_HIWORD_MASK, 0, },
+};
+
+/* clk_iomcu */
+static const struct hisi_gate_clock hi3660_iomcu_gate_sep_clks[] = {
+ { HI3660_CLK_I2C0_IOMCU, "clk_i2c0_iomcu", "clk_fll_src",
+ CLK_SET_RATE_PARENT, 0x10, 3, 0, },
+ { HI3660_CLK_I2C1_IOMCU, "clk_i2c1_iomcu", "clk_fll_src",
+ CLK_SET_RATE_PARENT, 0x10, 4, 0, },
+ { HI3660_CLK_I2C2_IOMCU, "clk_i2c2_iomcu", "clk_fll_src",
+ CLK_SET_RATE_PARENT, 0x10, 5, 0, },
+ { HI3660_CLK_I2C6_IOMCU, "clk_i2c6_iomcu", "clk_fll_src",
+ CLK_SET_RATE_PARENT, 0x10, 27, 0, },
+ { HI3660_CLK_IOMCU_PERI0, "iomcu_peri0", "clk_ppll0",
+ CLK_SET_RATE_PARENT, 0x90, 0, 0, },
+};
+
+static void hi3660_clk_iomcu_init(struct device_node *np)
+{
+ struct hisi_clock_data *clk_data;
+ int nr = ARRAY_SIZE(hi3660_iomcu_gate_sep_clks);
+
+ clk_data = hisi_clk_init(np, nr);
+ if (!clk_data)
+ return;
+
+ hisi_clk_register_gate_sep(hi3660_iomcu_gate_sep_clks,
+ ARRAY_SIZE(hi3660_iomcu_gate_sep_clks),
+ clk_data);
+}
+
+static void hi3660_clk_pmuctrl_init(struct device_node *np)
+{
+ struct hisi_clock_data *clk_data;
+ int nr = ARRAY_SIZE(hi3660_pmu_gate_clks);
+
+ clk_data = hisi_clk_init(np, nr);
+ if (!clk_data)
+ return;
+
+ hisi_clk_register_gate(hi3660_pmu_gate_clks,
+ ARRAY_SIZE(hi3660_pmu_gate_clks), clk_data);
+}
+
+static void hi3660_clk_pctrl_init(struct device_node *np)
+{
+ struct hisi_clock_data *clk_data;
+ int nr = ARRAY_SIZE(hi3660_pctrl_gate_clks);
+
+ clk_data = hisi_clk_init(np, nr);
+ if (!clk_data)
+ return;
+ hisi_clk_register_gate(hi3660_pctrl_gate_clks,
+ ARRAY_SIZE(hi3660_pctrl_gate_clks), clk_data);
+}
+
+static void hi3660_clk_sctrl_init(struct device_node *np)
+{
+ struct hisi_clock_data *clk_data;
+ int nr = ARRAY_SIZE(hi3660_sctrl_gate_clks) +
+ ARRAY_SIZE(hi3660_sctrl_gate_sep_clks) +
+ ARRAY_SIZE(hi3660_sctrl_mux_clks) +
+ ARRAY_SIZE(hi3660_sctrl_divider_clks);
+
+ clk_data = hisi_clk_init(np, nr);
+ if (!clk_data)
+ return;
+ hisi_clk_register_gate(hi3660_sctrl_gate_clks,
+ ARRAY_SIZE(hi3660_sctrl_gate_clks), clk_data);
+ hisi_clk_register_gate_sep(hi3660_sctrl_gate_sep_clks,
+ ARRAY_SIZE(hi3660_sctrl_gate_sep_clks),
+ clk_data);
+ hisi_clk_register_mux(hi3660_sctrl_mux_clks,
+ ARRAY_SIZE(hi3660_sctrl_mux_clks), clk_data);
+ hisi_clk_register_divider(hi3660_sctrl_divider_clks,
+ ARRAY_SIZE(hi3660_sctrl_divider_clks),
+ clk_data);
+}
+
+static void hi3660_clk_crgctrl_init(struct device_node *np)
+{
+ struct hisi_clock_data *clk_data;
+ int nr = ARRAY_SIZE(hi3660_fixed_rate_clks) +
+ ARRAY_SIZE(hi3660_crgctrl_gate_sep_clks) +
+ ARRAY_SIZE(hi3660_crgctrl_gate_clks) +
+ ARRAY_SIZE(hi3660_crgctrl_mux_clks) +
+ ARRAY_SIZE(hi3660_crg_fixed_factor_clks) +
+ ARRAY_SIZE(hi3660_crgctrl_divider_clks);
+
+ clk_data = hisi_clk_init(np, nr);
+ if (!clk_data)
+ return;
+
+ hisi_clk_register_fixed_rate(hi3660_fixed_rate_clks,
+ ARRAY_SIZE(hi3660_fixed_rate_clks),
+ clk_data);
+ hisi_clk_register_gate_sep(hi3660_crgctrl_gate_sep_clks,
+ ARRAY_SIZE(hi3660_crgctrl_gate_sep_clks),
+ clk_data);
+ hisi_clk_register_gate(hi3660_crgctrl_gate_clks,
+ ARRAY_SIZE(hi3660_crgctrl_gate_clks),
+ clk_data);
+ hisi_clk_register_mux(hi3660_crgctrl_mux_clks,
+ ARRAY_SIZE(hi3660_crgctrl_mux_clks),
+ clk_data);
+ hisi_clk_register_fixed_factor(hi3660_crg_fixed_factor_clks,
+ ARRAY_SIZE(hi3660_crg_fixed_factor_clks),
+ clk_data);
+ hisi_clk_register_divider(hi3660_crgctrl_divider_clks,
+ ARRAY_SIZE(hi3660_crgctrl_divider_clks),
+ clk_data);
+}
+
+static const struct of_device_id hi3660_clk_match_table[] = {
+ { .compatible = "hisilicon,hi3660-crgctrl",
+ .data = (void *)HI3660_CRGCTRL },
+ { .compatible = "hisilicon,hi3660-pctrl",
+ .data = (void *)HI3660_PCTRL },
+ { .compatible = "hisilicon,hi3660-pmuctrl",
+ .data = (void *)HI3660_PMUCTRL },
+ { .compatible = "hisilicon,hi3660-sctrl",
+ .data = (void *)HI3660_SCTRL },
+ { .compatible = "hisilicon,hi3660-iomcu",
+ .data = (void *)HI3660_IOMCU },
+ { }
+};
+
+static int hi3660_clk_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = pdev->dev.of_node;
+ enum hi3660_clk_type type;
+
+ type = (enum hi3660_clk_type)of_device_get_match_data(dev);
+ if (!type)
+ return -ENODEV;
+
+ switch (type) {
+ case HI3660_CRGCTRL:
+ hi3660_clk_crgctrl_init(np);
+ break;
+ case HI3660_PCTRL:
+ hi3660_clk_pctrl_init(np);
+ break;
+ case HI3660_PMUCTRL:
+ hi3660_clk_pmuctrl_init(np);
+ break;
+ case HI3660_SCTRL:
+ hi3660_clk_sctrl_init(np);
+ break;
+ case HI3660_IOMCU:
+ hi3660_clk_iomcu_init(np);
+ break;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static struct platform_driver hi3660_clk_driver = {
+ .probe = hi3660_clk_probe,
+ .driver = {
+ .name = "hi3660-clk",
+ .of_match_table = hi3660_clk_match_table,
+ },
+};
+
+static int __init hi3660_clk_init(void)
+{
+ return platform_driver_register(&hi3660_clk_driver);
+}
+core_initcall(hi3660_clk_init);
diff --git a/include/dt-bindings/clock/hi3660-clock.h b/include/dt-bindings/clock/hi3660-clock.h
new file mode 100644
index 0000000..1c00b7f
--- /dev/null
+++ b/include/dt-bindings/clock/hi3660-clock.h
@@ -0,0 +1,194 @@
+/*
+ * Copyright (c) 2016-2017 Linaro Ltd.
+ * Copyright (c) 2016-2017 HiSilicon Technologies Co., Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __DTS_HI3660_CLOCK_H
+#define __DTS_HI3660_CLOCK_H
+
+/* fixed rate clocks */
+#define HI3660_CLKIN_SYS 0
+#define HI3660_CLKIN_REF 1
+#define HI3660_CLK_FLL_SRC 2
+#define HI3660_CLK_PPLL0 3
+#define HI3660_CLK_PPLL1 4
+#define HI3660_CLK_PPLL2 5
+#define HI3660_CLK_PPLL3 6
+#define HI3660_CLK_SCPLL 7
+#define HI3660_PCLK 8
+#define HI3660_CLK_UART0_DBG 9
+#define HI3660_CLK_UART6 10
+#define HI3660_OSC32K 11
+#define HI3660_OSC19M 12
+#define HI3660_CLK_480M 13
+#define HI3660_CLK_INV 14
+
+/* clk in crgctrl */
+#define HI3660_FACTOR_UART3 15
+#define HI3660_CLK_FACTOR_MMC 16
+#define HI3660_CLK_GATE_I2C0 17
+#define HI3660_CLK_GATE_I2C1 18
+#define HI3660_CLK_GATE_I2C2 19
+#define HI3660_CLK_GATE_I2C6 20
+#define HI3660_CLK_DIV_SYSBUS 21
+#define HI3660_CLK_DIV_320M 22
+#define HI3660_CLK_DIV_A53 23
+#define HI3660_CLK_GATE_SPI0 24
+#define HI3660_CLK_GATE_SPI2 25
+#define HI3660_PCIEPHY_REF 26
+#define HI3660_CLK_ABB_USB 27
+#define HI3660_HCLK_GATE_SDIO0 28
+#define HI3660_HCLK_GATE_SD 29
+#define HI3660_CLK_GATE_AOMM 30
+#define HI3660_PCLK_GPIO0 31
+#define HI3660_PCLK_GPIO1 32
+#define HI3660_PCLK_GPIO2 33
+#define HI3660_PCLK_GPIO3 34
+#define HI3660_PCLK_GPIO4 35
+#define HI3660_PCLK_GPIO5 36
+#define HI3660_PCLK_GPIO6 37
+#define HI3660_PCLK_GPIO7 38
+#define HI3660_PCLK_GPIO8 39
+#define HI3660_PCLK_GPIO9 40
+#define HI3660_PCLK_GPIO10 41
+#define HI3660_PCLK_GPIO11 42
+#define HI3660_PCLK_GPIO12 43
+#define HI3660_PCLK_GPIO13 44
+#define HI3660_PCLK_GPIO14 45
+#define HI3660_PCLK_GPIO15 46
+#define HI3660_PCLK_GPIO16 47
+#define HI3660_PCLK_GPIO17 48
+#define HI3660_PCLK_GPIO18 49
+#define HI3660_PCLK_GPIO19 50
+#define HI3660_PCLK_GPIO20 51
+#define HI3660_PCLK_GPIO21 52
+#define HI3660_CLK_GATE_SPI3 53
+#define HI3660_CLK_GATE_I2C7 54
+#define HI3660_CLK_GATE_I2C3 55
+#define HI3660_CLK_GATE_SPI1 56
+#define HI3660_CLK_GATE_UART1 57
+#define HI3660_CLK_GATE_UART2 58
+#define HI3660_CLK_GATE_UART4 59
+#define HI3660_CLK_GATE_UART5 60
+#define HI3660_CLK_GATE_I2C4 61
+#define HI3660_CLK_GATE_DMAC 62
+#define HI3660_PCLK_GATE_DSS 63
+#define HI3660_ACLK_GATE_DSS 64
+#define HI3660_CLK_GATE_LDI1 65
+#define HI3660_CLK_GATE_LDI0 66
+#define HI3660_CLK_GATE_VIVOBUS 67
+#define HI3660_CLK_GATE_EDC0 68
+#define HI3660_CLK_GATE_TXDPHY0_CFG 69
+#define HI3660_CLK_GATE_TXDPHY0_REF 70
+#define HI3660_CLK_GATE_TXDPHY1_CFG 71
+#define HI3660_CLK_GATE_TXDPHY1_REF 72
+#define HI3660_ACLK_GATE_USB3OTG 73
+#define HI3660_CLK_GATE_SPI4 74
+#define HI3660_CLK_GATE_SD 75
+#define HI3660_CLK_GATE_SDIO0 76
+#define HI3660_CLK_GATE_UFS_SUBSYS 77
+#define HI3660_PCLK_GATE_DSI0 78
+#define HI3660_PCLK_GATE_DSI1 79
+#define HI3660_ACLK_GATE_PCIE 80
+#define HI3660_PCLK_GATE_PCIE_SYS 81
+#define HI3660_CLK_GATE_PCIEAUX 82
+#define HI3660_PCLK_GATE_PCIE_PHY 83
+#define HI3660_CLK_ANDGT_LDI0 84
+#define HI3660_CLK_ANDGT_LDI1 85
+#define HI3660_CLK_ANDGT_EDC0 86
+#define HI3660_CLK_GATE_UFSPHY_GT 87
+#define HI3660_CLK_ANDGT_MMC 88
+#define HI3660_CLK_ANDGT_SD 89
+#define HI3660_CLK_A53HPM_ANDGT 90
+#define HI3660_CLK_ANDGT_SDIO 91
+#define HI3660_CLK_ANDGT_UART0 92
+#define HI3660_CLK_ANDGT_UART1 93
+#define HI3660_CLK_ANDGT_UARTH 94
+#define HI3660_CLK_ANDGT_SPI 95
+#define HI3660_CLK_VIVOBUS_ANDGT 96
+#define HI3660_CLK_AOMM_ANDGT 97
+#define HI3660_CLK_320M_PLL_GT 98
+#define HI3660_AUTODIV_EMMC0BUS 99
+#define HI3660_AUTODIV_SYSBUS 100
+#define HI3660_CLK_GATE_UFSPHY_CFG 101
+#define HI3660_CLK_GATE_UFSIO_REF 102
+#define HI3660_CLK_MUX_SYSBUS 103
+#define HI3660_CLK_MUX_UART0 104
+#define HI3660_CLK_MUX_UART1 105
+#define HI3660_CLK_MUX_UARTH 106
+#define HI3660_CLK_MUX_SPI 107
+#define HI3660_CLK_MUX_I2C 108
+#define HI3660_CLK_MUX_MMC_PLL 109
+#define HI3660_CLK_MUX_LDI1 110
+#define HI3660_CLK_MUX_LDI0 111
+#define HI3660_CLK_MUX_SD_PLL 112
+#define HI3660_CLK_MUX_SD_SYS 113
+#define HI3660_CLK_MUX_EDC0 114
+#define HI3660_CLK_MUX_SDIO_SYS 115
+#define HI3660_CLK_MUX_SDIO_PLL 116
+#define HI3660_CLK_MUX_VIVOBUS 117
+#define HI3660_CLK_MUX_A53HPM 118
+#define HI3660_CLK_MUX_320M 119
+#define HI3660_CLK_MUX_IOPERI 120
+#define HI3660_CLK_DIV_UART0 121
+#define HI3660_CLK_DIV_UART1 122
+#define HI3660_CLK_DIV_UARTH 123
+#define HI3660_CLK_DIV_MMC 124
+#define HI3660_CLK_DIV_SD 125
+#define HI3660_CLK_DIV_EDC0 126
+#define HI3660_CLK_DIV_LDI0 127
+#define HI3660_CLK_DIV_SDIO 128
+#define HI3660_CLK_DIV_LDI1 129
+#define HI3660_CLK_DIV_SPI 130
+#define HI3660_CLK_DIV_VIVOBUS 131
+#define HI3660_CLK_DIV_I2C 132
+#define HI3660_CLK_DIV_UFSPHY 133
+#define HI3660_CLK_DIV_CFGBUS 134
+#define HI3660_CLK_DIV_MMC0BUS 135
+#define HI3660_CLK_DIV_MMC1BUS 136
+#define HI3660_CLK_DIV_UFSPERI 137
+#define HI3660_CLK_DIV_AOMM 138
+#define HI3660_CLK_DIV_IOPERI 139
+
+/* clk in pmuctrl */
+#define HI3660_GATE_ABB_192 0
+
+/* clk in pctrl */
+#define HI3660_GATE_UFS_TCXO_EN 0
+#define HI3660_GATE_USB_TCXO_EN 1
+
+/* clk in sctrl */
+#define HI3660_PCLK_AO_GPIO0 0
+#define HI3660_PCLK_AO_GPIO1 1
+#define HI3660_PCLK_AO_GPIO2 2
+#define HI3660_PCLK_AO_GPIO3 3
+#define HI3660_PCLK_AO_GPIO4 4
+#define HI3660_PCLK_AO_GPIO5 5
+#define HI3660_PCLK_AO_GPIO6 6
+#define HI3660_PCLK_GATE_MMBUF 7
+#define HI3660_CLK_GATE_DSS_AXI_MM 8
+#define HI3660_PCLK_MMBUF_ANDGT 9
+#define HI3660_CLK_MMBUF_PLL_ANDGT 10
+#define HI3660_CLK_FLL_MMBUF_ANDGT 11
+#define HI3660_CLK_SYS_MMBUF_ANDGT 12
+#define HI3660_CLK_GATE_PCIEPHY_GT 13
+#define HI3660_ACLK_MUX_MMBUF 14
+#define HI3660_CLK_SW_MMBUF 15
+#define HI3660_CLK_DIV_AOBUS 16
+#define HI3660_PCLK_DIV_MMBUF 17
+#define HI3660_ACLK_DIV_MMBUF 18
+#define HI3660_CLK_DIV_PCIEPHY 19
+
+/* clk in iomcu */
+#define HI3660_CLK_I2C0_IOMCU 0
+#define HI3660_CLK_I2C1_IOMCU 1
+#define HI3660_CLK_I2C2_IOMCU 2
+#define HI3660_CLK_I2C6_IOMCU 3
+#define HI3660_CLK_IOMCU_PERI0 4
+
+#endif /* __DTS_HI3660_CLOCK_H */
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 0/4] clk: rockchip: support clk controller for rk3328 SoC
From: Elaine Zhang @ 2016-12-29 2:45 UTC (permalink / raw)
To: heiko, mturquette, sboyd, xf
Cc: robh+dt, mark.rutland, linux-clk, huangtao, xxx, cl,
linux-rockchip, linux-kernel, devicetree, linux-arm-kernel,
Elaine Zhang
Changes in v5:
fix up some code style, remove grf clk init and cru dump.
Changes in v4:
dropping the "rockchip,cru" and "syscon" properties for bindings of rk3328
adjust the pacth 3 and 4 order.
move pll_rk3328 to patch 3.
Changes in v3:
fix up the pll type pll_rk3328 description and use.
Changes in v2:
add bindings for rk3328 clock controller
Elaine Zhang (4):
clk: rockchip: add dt-binding header for rk3328
dt-bindings: add bindings for rk3328 clock controller
clk: rockchip: add new pll-type for rk3328
clk: rockchip: add clock controller for rk3328
.../bindings/clock/rockchip,rk3328-cru.txt | 57 ++
drivers/clk/rockchip/Makefile | 1 +
drivers/clk/rockchip/clk-pll.c | 16 +-
drivers/clk/rockchip/clk-rk3328.c | 896 +++++++++++++++++++++
drivers/clk/rockchip/clk.h | 19 +
include/dt-bindings/clock/rk3328-cru.h | 403 +++++++++
6 files changed, 1389 insertions(+), 3 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
create mode 100644 drivers/clk/rockchip/clk-rk3328.c
create mode 100644 include/dt-bindings/clock/rk3328-cru.h
--
1.9.1
^ permalink raw reply
* [PATCH v5 1/4] clk: rockchip: add dt-binding header for rk3328
From: Elaine Zhang @ 2016-12-29 2:45 UTC (permalink / raw)
To: heiko-4mtYJXux2i+zQB+pC5nmwQ, mturquette-rdvid1DuHRBWk0Htik3J/w,
sboyd-sgV2jX0FEOL9JmXXK+q4OQ, xf-TNX95d0MmH7DzftRWevZcw
Cc: mark.rutland-5wv7dgnIgG8, huangtao-TNX95d0MmH7DzftRWevZcw,
devicetree-u79uwXL29TY76Z2rM5mHXA, xxx-TNX95d0MmH7DzftRWevZcw,
Elaine Zhang, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-clk-u79uwXL29TY76Z2rM5mHXA, cl-TNX95d0MmH7DzftRWevZcw
In-Reply-To: <1482979511-6847-1-git-send-email-zhangqing-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Add the dt-bindings header for the rk3328, that gets shared between
the clock controller and the clock references in the dts.
Add softreset ID for rk3328.
Signed-off-by: Elaine Zhang <zhangqing-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
---
include/dt-bindings/clock/rk3328-cru.h | 403 +++++++++++++++++++++++++++++++++
1 file changed, 403 insertions(+)
create mode 100644 include/dt-bindings/clock/rk3328-cru.h
diff --git a/include/dt-bindings/clock/rk3328-cru.h b/include/dt-bindings/clock/rk3328-cru.h
new file mode 100644
index 000000000000..545ed7541316
--- /dev/null
+++ b/include/dt-bindings/clock/rk3328-cru.h
@@ -0,0 +1,403 @@
+/*
+ * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
+ * Author: Elaine <zhangqing-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK3328_H
+#define _DT_BINDINGS_CLK_ROCKCHIP_RK3328_H
+
+/* core clocks */
+#define PLL_APLL 1
+#define PLL_DPLL 2
+#define PLL_CPLL 3
+#define PLL_GPLL 4
+#define PLL_NPLL 5
+#define ARMCLK 6
+
+/* sclk gates (special clocks) */
+#define SCLK_RTC32K 30
+#define SCLK_SDMMC_EXT 31
+#define SCLK_SPI 32
+#define SCLK_SDMMC 33
+#define SCLK_SDIO 34
+#define SCLK_EMMC 35
+#define SCLK_TSADC 36
+#define SCLK_SARADC 37
+#define SCLK_UART0 38
+#define SCLK_UART1 39
+#define SCLK_UART2 40
+#define SCLK_I2S0 41
+#define SCLK_I2S1 42
+#define SCLK_I2S2 43
+#define SCLK_I2S1_OUT 44
+#define SCLK_I2S2_OUT 45
+#define SCLK_SPDIF 46
+#define SCLK_TIMER0 47
+#define SCLK_TIMER1 48
+#define SCLK_TIMER2 49
+#define SCLK_TIMER3 50
+#define SCLK_TIMER4 51
+#define SCLK_TIMER5 52
+#define SCLK_WIFI 53
+#define SCLK_CIF_OUT 54
+#define SCLK_I2C0 55
+#define SCLK_I2C1 56
+#define SCLK_I2C2 57
+#define SCLK_I2C3 58
+#define SCLK_CRYPTO 59
+#define SCLK_PWM 60
+#define SCLK_PDM 61
+#define SCLK_EFUSE 62
+#define SCLK_OTP 63
+#define SCLK_DDRCLK 64
+#define SCLK_VDEC_CABAC 65
+#define SCLK_VDEC_CORE 66
+#define SCLK_VENC_DSP 67
+#define SCLK_VENC_CORE 68
+#define SCLK_RGA 69
+#define SCLK_HDMI_SFC 70
+#define SCLK_HDMI_CEC 71
+#define SCLK_USB3_REF 72
+#define SCLK_USB3_SUSPEND 73
+#define SCLK_SDMMC_DRV 74
+#define SCLK_SDIO_DRV 75
+#define SCLK_EMMC_DRV 76
+#define SCLK_SDMMC_EXT_DRV 77
+#define SCLK_SDMMC_SAMPLE 78
+#define SCLK_SDIO_SAMPLE 79
+#define SCLK_EMMC_SAMPLE 80
+#define SCLK_SDMMC_EXT_SAMPLE 81
+#define SCLK_VOP 82
+#define SCLK_MAC2PHY_RXTX 83
+#define SCLK_MAC2PHY_SRC 84
+#define SCLK_MAC2PHY_REF 85
+#define SCLK_MAC2PHY_OUT 86
+#define SCLK_MAC2IO_RX 87
+#define SCLK_MAC2IO_TX 88
+#define SCLK_MAC2IO_REFOUT 89
+#define SCLK_MAC2IO_REF 90
+#define SCLK_MAC2IO_OUT 91
+#define SCLK_TSP 92
+#define SCLK_HSADC_TSP 93
+#define SCLK_USB3PHY_REF 94
+#define SCLK_REF_USB3OTG 95
+#define SCLK_USB3OTG_REF 96
+#define SCLK_USB3OTG_SUSPEND 97
+#define SCLK_REF_USB3OTG_SRC 98
+#define SCLK_MAC2IO_SRC 99
+
+/* dclk gates */
+#define DCLK_LCDC 180
+#define DCLK_HDMIPHY 181
+#define HDMIPHY 182
+#define USB480M 183
+#define DCLK_LCDC_SRC 184
+
+/* aclk gates */
+#define ACLK_AXISRAM 190
+#define ACLK_VOP_PRE 191
+#define ACLK_USB3OTG 192
+#define ACLK_RGA_PRE 193
+#define ACLK_DMAC 194
+#define ACLK_GPU 195
+#define ACLK_BUS_PRE 196
+#define ACLK_PERI_PRE 197
+#define ACLK_RKVDEC_PRE 198
+#define ACLK_RKVDEC 199
+#define ACLK_RKVENC 200
+#define ACLK_VPU_PRE 201
+#define ACLK_VIO_PRE 202
+#define ACLK_VPU 203
+#define ACLK_VIO 204
+#define ACLK_VOP 205
+#define ACLK_GMAC 206
+#define ACLK_H265 207
+#define ACLK_H264 208
+#define ACLK_MAC2PHY 209
+#define ACLK_MAC2IO 210
+#define ACLK_DCF 211
+#define ACLK_TSP 212
+#define ACLK_PERI 213
+#define ACLK_RGA 214
+#define ACLK_IEP 215
+#define ACLK_CIF 216
+#define ACLK_HDCP 217
+
+/* pclk gates */
+#define PCLK_GPIO0 300
+#define PCLK_GPIO1 301
+#define PCLK_GPIO2 302
+#define PCLK_GPIO3 303
+#define PCLK_GRF 304
+#define PCLK_I2C0 305
+#define PCLK_I2C1 306
+#define PCLK_I2C2 307
+#define PCLK_I2C3 308
+#define PCLK_SPI 309
+#define PCLK_UART0 310
+#define PCLK_UART1 311
+#define PCLK_UART2 312
+#define PCLK_TSADC 313
+#define PCLK_PWM 314
+#define PCLK_TIMER 315
+#define PCLK_BUS_PRE 316
+#define PCLK_PERI_PRE 317
+#define PCLK_HDMI_CTRL 318
+#define PCLK_HDMI_PHY 319
+#define PCLK_GMAC 320
+#define PCLK_H265 321
+#define PCLK_MAC2PHY 322
+#define PCLK_MAC2IO 323
+#define PCLK_USB3PHY_OTG 324
+#define PCLK_USB3PHY_PIPE 325
+#define PCLK_USB3_GRF 326
+#define PCLK_USB2_GRF 327
+#define PCLK_HDMIPHY 328
+#define PCLK_DDR 329
+#define PCLK_PERI 330
+#define PCLK_HDMI 331
+#define PCLK_HDCP 332
+#define PCLK_DCF 333
+#define PCLK_SARADC 334
+
+/* hclk gates */
+#define HCLK_PERI 408
+#define HCLK_TSP 409
+#define HCLK_GMAC 410
+#define HCLK_I2S0_8CH 411
+#define HCLK_I2S1_8CH 413
+#define HCLK_I2S2_2CH 413
+#define HCLK_SPDIF_8CH 414
+#define HCLK_VOP 415
+#define HCLK_NANDC 416
+#define HCLK_SDMMC 417
+#define HCLK_SDIO 418
+#define HCLK_EMMC 419
+#define HCLK_SDMMC_EXT 420
+#define HCLK_RKVDEC_PRE 421
+#define HCLK_RKVDEC 422
+#define HCLK_RKVENC 423
+#define HCLK_VPU_PRE 424
+#define HCLK_VIO_PRE 425
+#define HCLK_VPU 426
+#define HCLK_VIO 427
+#define HCLK_BUS_PRE 428
+#define HCLK_PERI_PRE 429
+#define HCLK_H264 430
+#define HCLK_CIF 431
+#define HCLK_OTG_PMU 432
+#define HCLK_OTG 433
+#define HCLK_HOST0 434
+#define HCLK_HOST0_ARB 435
+#define HCLK_CRYPTO_MST 436
+#define HCLK_CRYPTO_SLV 437
+#define HCLK_PDM 438
+#define HCLK_IEP 439
+#define HCLK_RGA 440
+#define HCLK_HDCP 441
+
+#define CLK_NR_CLKS (HCLK_HDCP + 1)
+
+#define SCLK_MAC2IO 0
+#define SCLK_MAC2PHY 1
+
+#define CLKGRF_NR_CLKS (SCLK_MAC2PHY + 1)
+
+/* soft-reset indices */
+#define SRST_CORE0_PO 0
+#define SRST_CORE1_PO 1
+#define SRST_CORE2_PO 2
+#define SRST_CORE3_PO 3
+#define SRST_CORE0 4
+#define SRST_CORE1 5
+#define SRST_CORE2 6
+#define SRST_CORE3 7
+#define SRST_CORE0_DBG 8
+#define SRST_CORE1_DBG 9
+#define SRST_CORE2_DBG 10
+#define SRST_CORE3_DBG 11
+#define SRST_TOPDBG 12
+#define SRST_CORE_NIU 13
+#define SRST_STRC_A 14
+#define SRST_L2C 15
+
+#define SRST_A53_GIC 18
+#define SRST_DAP 19
+#define SRST_PMU_P 21
+#define SRST_EFUSE 22
+#define SRST_BUSSYS_H 23
+#define SRST_BUSSYS_P 24
+#define SRST_SPDIF 25
+#define SRST_INTMEM 26
+#define SRST_ROM 27
+#define SRST_GPIO0 28
+#define SRST_GPIO1 29
+#define SRST_GPIO2 30
+#define SRST_GPIO3 31
+
+#define SRST_I2S0 32
+#define SRST_I2S1 33
+#define SRST_I2S2 34
+#define SRST_I2S0_H 35
+#define SRST_I2S1_H 36
+#define SRST_I2S2_H 37
+#define SRST_UART0 38
+#define SRST_UART1 39
+#define SRST_UART2 40
+#define SRST_UART0_P 41
+#define SRST_UART1_P 42
+#define SRST_UART2_P 43
+#define SRST_I2C0 44
+#define SRST_I2C1 45
+#define SRST_I2C2 46
+#define SRST_I2C3 47
+
+#define SRST_I2C0_P 48
+#define SRST_I2C1_P 49
+#define SRST_I2C2_P 50
+#define SRST_I2C3_P 51
+#define SRST_EFUSE_SE_P 52
+#define SRST_EFUSE_NS_P 53
+#define SRST_PWM0 54
+#define SRST_PWM0_P 55
+#define SRST_DMA 56
+#define SRST_TSP_A 57
+#define SRST_TSP_H 58
+#define SRST_TSP 59
+#define SRST_TSP_HSADC 60
+#define SRST_DCF_A 61
+#define SRST_DCF_P 62
+
+#define SRST_SCR 64
+#define SRST_SPI 65
+#define SRST_TSADC 66
+#define SRST_TSADC_P 67
+#define SRST_CRYPTO 68
+#define SRST_SGRF 69
+#define SRST_GRF 70
+#define SRST_USB_GRF 71
+#define SRST_TIMER_6CH_P 72
+#define SRST_TIMER0 73
+#define SRST_TIMER1 74
+#define SRST_TIMER2 75
+#define SRST_TIMER3 76
+#define SRST_TIMER4 77
+#define SRST_TIMER5 78
+#define SRST_USB3GRF 79
+
+#define SRST_PHYNIU 80
+#define SRST_HDMIPHY 81
+#define SRST_VDAC 82
+#define SRST_ACODEC_p 83
+#define SRST_SARADC 85
+#define SRST_SARADC_P 86
+#define SRST_GRF_DDR 87
+#define SRST_DFIMON 88
+#define SRST_MSCH 89
+#define SRST_DDRMSCH 91
+#define SRST_DDRCTRL 92
+#define SRST_DDRCTRL_P 93
+#define SRST_DDRPHY 94
+#define SRST_DDRPHY_P 95
+
+#define SRST_GMAC_NIU_A 96
+#define SRST_GMAC_NIU_P 97
+#define SRST_GMAC2PHY_A 98
+#define SRST_GMAC2IO_A 99
+#define SRST_MACPHY 100
+#define SRST_OTP_PHY 101
+#define SRST_GPU_A 102
+#define SRST_GPU_NIU_A 103
+#define SRST_SDMMCEXT 104
+#define SRST_PERIPH_NIU_A 105
+#define SRST_PERIHP_NIU_H 106
+#define SRST_PERIHP_P 107
+#define SRST_PERIPHSYS_H 108
+#define SRST_MMC0 109
+#define SRST_SDIO 110
+#define SRST_EMMC 111
+
+#define SRST_USB2OTG_H 112
+#define SRST_USB2OTG 113
+#define SRST_USB2OTG_ADP 114
+#define SRST_USB2HOST_H 115
+#define SRST_USB2HOST_ARB 116
+#define SRST_USB2HOST_AUX 117
+#define SRST_USB2HOST_EHCIPHY 118
+#define SRST_USB2HOST_UTMI 119
+#define SRST_USB3OTG 120
+#define SRST_USBPOR 121
+#define SRST_USB2OTG_UTMI 122
+#define SRST_USB2HOST_PHY_UTMI 123
+#define SRST_USB3OTG_UTMI 124
+#define SRST_USB3PHY_U2 125
+#define SRST_USB3PHY_U3 126
+#define SRST_USB3PHY_PIPE 127
+
+#define SRST_VIO_A 128
+#define SRST_VIO_BUS_H 129
+#define SRST_VIO_H2P_H 130
+#define SRST_VIO_ARBI_H 131
+#define SRST_VOP_NIU_A 132
+#define SRST_VOP_A 133
+#define SRST_VOP_H 134
+#define SRST_VOP_D 135
+#define SRST_RGA 136
+#define SRST_RGA_NIU_A 137
+#define SRST_RGA_A 138
+#define SRST_RGA_H 139
+#define SRST_IEP_A 140
+#define SRST_IEP_H 141
+#define SRST_HDMI 142
+#define SRST_HDMI_P 143
+
+#define SRST_HDCP_A 144
+#define SRST_HDCP 145
+#define SRST_HDCP_H 146
+#define SRST_CIF_A 147
+#define SRST_CIF_H 148
+#define SRST_CIF_P 149
+#define SRST_OTP_P 150
+#define SRST_OTP_SBPI 151
+#define SRST_OTP_USER 152
+#define SRST_DDRCTRL_A 153
+#define SRST_DDRSTDY_P 154
+#define SRST_DDRSTDY 155
+#define SRST_PDM_H 156
+#define SRST_PDM 157
+#define SRST_USB3PHY_OTG_P 158
+#define SRST_USB3PHY_PIPE_P 159
+
+#define SRST_VCODEC_A 160
+#define SRST_VCODEC_NIU_A 161
+#define SRST_VCODEC_H 162
+#define SRST_VCODEC_NIU_H 163
+#define SRST_VDEC_A 164
+#define SRST_VDEC_NIU_A 165
+#define SRST_VDEC_H 166
+#define SRST_VDEC_NIU_H 167
+#define SRST_VDEC_CORE 168
+#define SRST_VDEC_CABAC 169
+#define SRST_DDRPHYDIV 175
+
+#define SRST_RKVENC_NIU_A 176
+#define SRST_RKVENC_NIU_H 177
+#define SRST_RKVENC_H265_A 178
+#define SRST_RKVENC_H265_P 179
+#define SRST_RKVENC_H265_CORE 180
+#define SRST_RKVENC_H265_DSP 181
+#define SRST_RKVENC_H264_A 182
+#define SRST_RKVENC_H264_H 183
+#define SRST_RKVENC_INTMEM 184
+
+#endif
--
1.9.1
^ permalink raw reply related
* [PATCH v5 2/4] dt-bindings: add bindings for rk3328 clock controller
From: Elaine Zhang @ 2016-12-29 2:45 UTC (permalink / raw)
To: heiko, mturquette, sboyd, xf
Cc: robh+dt, mark.rutland, linux-clk, huangtao, xxx, cl,
linux-rockchip, linux-kernel, devicetree, linux-arm-kernel,
Elaine Zhang
In-Reply-To: <1482979511-6847-1-git-send-email-zhangqing@rock-chips.com>
Add devicetree bindings for Rockchip cru which found on
Rockchip SoCs.
Changes in v4:
dropping the "rockchip,cru" and "syscon" properties for bindings of rk3328
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
---
.../bindings/clock/rockchip,rk3328-cru.txt | 57 ++++++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
new file mode 100644
index 000000000000..e71c675ba5da
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt
@@ -0,0 +1,57 @@
+* Rockchip RK3328 Clock and Reset Unit
+
+The RK3328 clock controller generates and supplies clock to various
+controllers within the SoC and also implements a reset controller for SoC
+peripherals.
+
+Required Properties:
+
+- compatible: should be "rockchip,rk3328-cru"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- #clock-cells: should be 1.
+- #reset-cells: should be 1.
+
+Optional Properties:
+
+- rockchip,grf: phandle to the syscon managing the "general register files"
+ If missing pll rates are not changeable, due to the missing pll lock status.
+
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume. All available clocks are defined as
+preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be
+used in device tree sources. Similar macros exist for the reset sources in
+these files.
+
+External clocks:
+
+There are several clocks that are generated outside the SoC. It is expected
+that they are defined using standard clock bindings with following
+clock-output-names:
+ - "xin24m" - crystal input - required,
+ - "clkin_i2s" - external I2S clock - optional,
+ - "gmac_clkin" - external GMAC clock - optional
+ - "phy_50m_out" - output clock of the pll in the mac phy
+
+Example: Clock controller node:
+
+ cru: clock-controller@ff440000 {
+ compatible = "rockchip,rk3328-cru";
+ reg = <0x0 0xff440000 0x0 0x1000>;
+ rockchip,grf = <&grf>;
+
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+Example: UART controller node that consumes the clock generated by the clock
+ controller:
+
+ uart0: serial@ff120000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0xff120000 0x100>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&cru SCLK_UART0>;
+ };
--
1.9.1
^ permalink raw reply related
* [PATCH v5 3/4] clk: rockchip: add new pll-type for rk3328
From: Elaine Zhang @ 2016-12-29 2:45 UTC (permalink / raw)
To: heiko, mturquette, sboyd, xf
Cc: robh+dt, mark.rutland, linux-clk, huangtao, xxx, cl,
linux-rockchip, linux-kernel, devicetree, linux-arm-kernel,
Elaine Zhang
In-Reply-To: <1482979511-6847-1-git-send-email-zhangqing@rock-chips.com>
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Changes in v4:
adjust the pacth 3 and 4 order.
move pll_rk3328 to patch 3.
Changes in v3:
fix up the pll type pll_rk3328 description and use
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
---
drivers/clk/rockchip/clk-pll.c | 16 +++++++++++++---
drivers/clk/rockchip/clk.h | 1 +
2 files changed, 14 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/rockchip/clk-pll.c b/drivers/clk/rockchip/clk-pll.c
index 6ed605776abd..eec51893a7e6 100644
--- a/drivers/clk/rockchip/clk-pll.c
+++ b/drivers/clk/rockchip/clk-pll.c
@@ -29,6 +29,7 @@
#define PLL_MODE_SLOW 0x0
#define PLL_MODE_NORM 0x1
#define PLL_MODE_DEEP 0x2
+#define PLL_RK3328_MODE_MASK 0x1
struct rockchip_clk_pll {
struct clk_hw hw;
@@ -848,7 +849,8 @@ struct clk *rockchip_clk_register_pll(struct rockchip_clk_provider *ctx,
struct clk *pll_clk, *mux_clk;
char pll_name[20];
- if (num_parents != 2) {
+ if ((pll_type != pll_rk3328 && num_parents != 2) ||
+ (pll_type == pll_rk3328 && num_parents != 1)) {
pr_err("%s: needs two parent clocks\n", __func__);
return ERR_PTR(-EINVAL);
}
@@ -865,13 +867,17 @@ struct clk *rockchip_clk_register_pll(struct rockchip_clk_provider *ctx,
pll_mux = &pll->pll_mux;
pll_mux->reg = ctx->reg_base + mode_offset;
pll_mux->shift = mode_shift;
- pll_mux->mask = PLL_MODE_MASK;
+ if (pll_type == pll_rk3328)
+ pll_mux->mask = PLL_RK3328_MODE_MASK;
+ else
+ pll_mux->mask = PLL_MODE_MASK;
pll_mux->flags = 0;
pll_mux->lock = &ctx->lock;
pll_mux->hw.init = &init;
if (pll_type == pll_rk3036 ||
pll_type == pll_rk3066 ||
+ pll_type == pll_rk3328 ||
pll_type == pll_rk3399)
pll_mux->flags |= CLK_MUX_HIWORD_MASK;
@@ -884,7 +890,10 @@ struct clk *rockchip_clk_register_pll(struct rockchip_clk_provider *ctx,
init.flags = CLK_SET_RATE_PARENT;
init.ops = pll->pll_mux_ops;
init.parent_names = pll_parents;
- init.num_parents = ARRAY_SIZE(pll_parents);
+ if (pll_type == pll_rk3328)
+ init.num_parents = 2;
+ else
+ init.num_parents = ARRAY_SIZE(pll_parents);
mux_clk = clk_register(NULL, &pll_mux->hw);
if (IS_ERR(mux_clk))
@@ -918,6 +927,7 @@ struct clk *rockchip_clk_register_pll(struct rockchip_clk_provider *ctx,
switch (pll_type) {
case pll_rk3036:
+ case pll_rk3328:
if (!pll->rate_table || IS_ERR(ctx->grf))
init.ops = &rockchip_rk3036_pll_clk_norate_ops;
else
diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h
index d67eecc4ade9..06acb7e0911f 100644
--- a/drivers/clk/rockchip/clk.h
+++ b/drivers/clk/rockchip/clk.h
@@ -130,6 +130,7 @@
enum rockchip_pll_type {
pll_rk3036,
pll_rk3066,
+ pll_rk3328,
pll_rk3399,
};
--
1.9.1
^ permalink raw reply related
* [PATCH v5 4/4] clk: rockchip: add clock controller for rk3328
From: Elaine Zhang @ 2016-12-29 2:45 UTC (permalink / raw)
To: heiko, mturquette, sboyd, xf
Cc: robh+dt, mark.rutland, linux-clk, huangtao, xxx, cl,
linux-rockchip, linux-kernel, devicetree, linux-arm-kernel,
Elaine Zhang
In-Reply-To: <1482979511-6847-1-git-send-email-zhangqing@rock-chips.com>
Add the clock tree definition for the new rk3328 SoC.
Changes in v5:
fix up some code style, remove grf clk init and cru dump.
Changes in v4:
adjust the pacth 3 and 4 order.
Changes in v3:
fix up the pll parent only xin24m.
Changes in v2:
fix up these *_sample error description.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
---
drivers/clk/rockchip/Makefile | 1 +
drivers/clk/rockchip/clk-rk3328.c | 896 ++++++++++++++++++++++++++++++++++++++
drivers/clk/rockchip/clk.h | 18 +
3 files changed, 915 insertions(+)
create mode 100644 drivers/clk/rockchip/clk-rk3328.c
diff --git a/drivers/clk/rockchip/Makefile b/drivers/clk/rockchip/Makefile
index 16e098c36f90..68b04bfca282 100644
--- a/drivers/clk/rockchip/Makefile
+++ b/drivers/clk/rockchip/Makefile
@@ -16,5 +16,6 @@ obj-y += clk-rk3036.o
obj-y += clk-rk3188.o
obj-y += clk-rk3228.o
obj-y += clk-rk3288.o
+obj-y += clk-rk3328.o
obj-y += clk-rk3368.o
obj-y += clk-rk3399.o
diff --git a/drivers/clk/rockchip/clk-rk3328.c b/drivers/clk/rockchip/clk-rk3328.c
new file mode 100644
index 000000000000..f486ec9e9471
--- /dev/null
+++ b/drivers/clk/rockchip/clk-rk3328.c
@@ -0,0 +1,896 @@
+/*
+ * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
+ * Author: Elaine <zhangqing@rock-chips.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/syscore_ops.h>
+#include <dt-bindings/clock/rk3328-cru.h>
+#include "clk.h"
+
+#define RK3328_GRF_SOC_STATUS0 0x480
+#define RK3328_GRF_MAC_CON1 0x904
+#define RK3328_GRF_MAC_CON2 0x908
+
+enum rk3328_plls {
+ apll, dpll, cpll, gpll, npll,
+};
+
+static struct rockchip_pll_rate_table rk3328_pll_rates[] = {
+ /* _mhz, _refdiv, _fbdiv, _postdiv1, _postdiv2, _dsmpd, _frac */
+ RK3036_PLL_RATE(1608000000, 1, 67, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1584000000, 1, 66, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1560000000, 1, 65, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1536000000, 1, 64, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1512000000, 1, 63, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1488000000, 1, 62, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1464000000, 1, 61, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1440000000, 1, 60, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1416000000, 1, 59, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1392000000, 1, 58, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1368000000, 1, 57, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1344000000, 1, 56, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1320000000, 1, 55, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1296000000, 1, 54, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1272000000, 1, 53, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1248000000, 1, 52, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1200000000, 1, 50, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1188000000, 2, 99, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1104000000, 1, 46, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1100000000, 12, 550, 1, 1, 1, 0),
+ RK3036_PLL_RATE(1008000000, 1, 84, 2, 1, 1, 0),
+ RK3036_PLL_RATE(1000000000, 6, 500, 2, 1, 1, 0),
+ RK3036_PLL_RATE(984000000, 1, 82, 2, 1, 1, 0),
+ RK3036_PLL_RATE(960000000, 1, 80, 2, 1, 1, 0),
+ RK3036_PLL_RATE(936000000, 1, 78, 2, 1, 1, 0),
+ RK3036_PLL_RATE(912000000, 1, 76, 2, 1, 1, 0),
+ RK3036_PLL_RATE(900000000, 4, 300, 2, 1, 1, 0),
+ RK3036_PLL_RATE(888000000, 1, 74, 2, 1, 1, 0),
+ RK3036_PLL_RATE(864000000, 1, 72, 2, 1, 1, 0),
+ RK3036_PLL_RATE(840000000, 1, 70, 2, 1, 1, 0),
+ RK3036_PLL_RATE(816000000, 1, 68, 2, 1, 1, 0),
+ RK3036_PLL_RATE(800000000, 6, 400, 2, 1, 1, 0),
+ RK3036_PLL_RATE(700000000, 6, 350, 2, 1, 1, 0),
+ RK3036_PLL_RATE(696000000, 1, 58, 2, 1, 1, 0),
+ RK3036_PLL_RATE(600000000, 1, 75, 3, 1, 1, 0),
+ RK3036_PLL_RATE(594000000, 2, 99, 2, 1, 1, 0),
+ RK3036_PLL_RATE(504000000, 1, 63, 3, 1, 1, 0),
+ RK3036_PLL_RATE(500000000, 6, 250, 2, 1, 1, 0),
+ RK3036_PLL_RATE(408000000, 1, 68, 2, 2, 1, 0),
+ RK3036_PLL_RATE(312000000, 1, 52, 2, 2, 1, 0),
+ RK3036_PLL_RATE(216000000, 1, 72, 4, 2, 1, 0),
+ RK3036_PLL_RATE(96000000, 1, 64, 4, 4, 1, 0),
+ { /* sentinel */ },
+};
+
+static struct rockchip_pll_rate_table rk3328_pll_frac_rates[] = {
+ /* _mhz, _refdiv, _fbdiv, _postdiv1, _postdiv2, _dsmpd, _frac */
+ RK3036_PLL_RATE(1016064000, 3, 127, 1, 1, 0, 134217),
+ /* vco = 1016064000 */
+ RK3036_PLL_RATE(983040000, 24, 983, 1, 1, 0, 671088),
+ /* vco = 983040000 */
+ RK3036_PLL_RATE(491520000, 24, 983, 2, 1, 0, 671088),
+ /* vco = 983040000 */
+ RK3036_PLL_RATE(61440000, 6, 215, 7, 2, 0, 671088),
+ /* vco = 860156000 */
+ RK3036_PLL_RATE(56448000, 12, 451, 4, 4, 0, 9797894),
+ /* vco = 903168000 */
+ RK3036_PLL_RATE(40960000, 12, 409, 4, 5, 0, 10066329),
+ /* vco = 819200000 */
+ { /* sentinel */ },
+};
+
+#define RK3328_DIV_ACLKM_MASK 0x7
+#define RK3328_DIV_ACLKM_SHIFT 4
+#define RK3328_DIV_PCLK_DBG_MASK 0xf
+#define RK3328_DIV_PCLK_DBG_SHIFT 0
+
+#define RK3328_CLKSEL1(_aclk_core, _pclk_dbg) \
+{ \
+ .reg = RK3328_CLKSEL_CON(1), \
+ .val = HIWORD_UPDATE(_aclk_core, RK3328_DIV_ACLKM_MASK, \
+ RK3328_DIV_ACLKM_SHIFT) | \
+ HIWORD_UPDATE(_pclk_dbg, RK3328_DIV_PCLK_DBG_MASK, \
+ RK3328_DIV_PCLK_DBG_SHIFT), \
+}
+
+#define RK3328_CPUCLK_RATE(_prate, _aclk_core, _pclk_dbg) \
+{ \
+ .prate = _prate, \
+ .divs = { \
+ RK3328_CLKSEL1(_aclk_core, _pclk_dbg), \
+ }, \
+}
+
+static struct rockchip_cpuclk_rate_table rk3328_cpuclk_rates[] __initdata = {
+ RK3328_CPUCLK_RATE(1800000000, 1, 7),
+ RK3328_CPUCLK_RATE(1704000000, 1, 7),
+ RK3328_CPUCLK_RATE(1608000000, 1, 7),
+ RK3328_CPUCLK_RATE(1512000000, 1, 7),
+ RK3328_CPUCLK_RATE(1488000000, 1, 5),
+ RK3328_CPUCLK_RATE(1416000000, 1, 5),
+ RK3328_CPUCLK_RATE(1392000000, 1, 5),
+ RK3328_CPUCLK_RATE(1296000000, 1, 5),
+ RK3328_CPUCLK_RATE(1200000000, 1, 5),
+ RK3328_CPUCLK_RATE(1104000000, 1, 5),
+ RK3328_CPUCLK_RATE(1008000000, 1, 5),
+ RK3328_CPUCLK_RATE(912000000, 1, 5),
+ RK3328_CPUCLK_RATE(816000000, 1, 3),
+ RK3328_CPUCLK_RATE(696000000, 1, 3),
+ RK3328_CPUCLK_RATE(600000000, 1, 3),
+ RK3328_CPUCLK_RATE(408000000, 1, 1),
+ RK3328_CPUCLK_RATE(312000000, 1, 1),
+ RK3328_CPUCLK_RATE(216000000, 1, 1),
+ RK3328_CPUCLK_RATE(96000000, 1, 1),
+};
+
+static const struct rockchip_cpuclk_reg_data rk3328_cpuclk_data = {
+ .core_reg = RK3328_CLKSEL_CON(0),
+ .div_core_shift = 0,
+ .div_core_mask = 0x1f,
+ .mux_core_alt = 1,
+ .mux_core_main = 3,
+ .mux_core_shift = 6,
+ .mux_core_mask = 0x3,
+};
+
+PNAME(mux_pll_p) = { "xin24m" };
+
+PNAME(mux_2plls_p) = { "cpll", "gpll" };
+PNAME(mux_gpll_cpll_p) = { "gpll", "cpll" };
+PNAME(mux_cpll_gpll_apll_p) = { "cpll", "gpll", "apll" };
+PNAME(mux_2plls_xin24m_p) = { "cpll", "gpll", "xin24m" };
+PNAME(mux_2plls_hdmiphy_p) = { "cpll", "gpll",
+ "dummy_hdmiphy" };
+PNAME(mux_4plls_p) = { "cpll", "gpll",
+ "dummy_hdmiphy",
+ "usb480m" };
+PNAME(mux_2plls_u480m_p) = { "cpll", "gpll",
+ "usb480m" };
+PNAME(mux_2plls_24m_u480m_p) = { "cpll", "gpll",
+ "xin24m", "usb480m" };
+
+PNAME(mux_ddrphy_p) = { "dpll", "apll", "cpll" };
+PNAME(mux_armclk_p) = { "apll_core",
+ "gpll_core",
+ "dpll_core",
+ "npll_core"};
+PNAME(mux_hdmiphy_p) = { "hdmi_phy", "xin24m" };
+PNAME(mux_usb480m_p) = { "usb480m_phy",
+ "xin24m" };
+
+PNAME(mux_i2s0_p) = { "clk_i2s0_div",
+ "clk_i2s0_frac",
+ "xin12m",
+ "xin12m" };
+PNAME(mux_i2s1_p) = { "clk_i2s1_div",
+ "clk_i2s1_frac",
+ "clkin_i2s1",
+ "xin12m" };
+PNAME(mux_i2s2_p) = { "clk_i2s2_div",
+ "clk_i2s2_frac",
+ "clkin_i2s2",
+ "xin12m" };
+PNAME(mux_i2s1out_p) = { "clk_i2s1", "xin12m"};
+PNAME(mux_i2s2out_p) = { "clk_i2s2", "xin12m" };
+PNAME(mux_spdif_p) = { "clk_spdif_div",
+ "clk_spdif_frac",
+ "xin12m",
+ "xin12m" };
+PNAME(mux_uart0_p) = { "clk_uart0_div",
+ "clk_uart0_frac",
+ "xin24m" };
+PNAME(mux_uart1_p) = { "clk_uart1_div",
+ "clk_uart1_frac",
+ "xin24m" };
+PNAME(mux_uart2_p) = { "clk_uart2_div",
+ "clk_uart2_frac",
+ "xin24m" };
+
+PNAME(mux_sclk_cif_p) = { "clk_cif_src",
+ "xin24m" };
+PNAME(mux_dclk_lcdc_p) = { "hdmiphy",
+ "dclk_lcdc_src" };
+PNAME(mux_aclk_peri_pre_p) = { "cpll_peri",
+ "gpll_peri",
+ "hdmiphy_peri" };
+PNAME(mux_ref_usb3otg_src_p) = { "xin24m",
+ "clk_usb3otg_ref" };
+PNAME(mux_xin24m_32k_p) = { "xin24m",
+ "clk_rtc32k" };
+PNAME(mux_mac2io_src_p) = { "clk_mac2io_src",
+ "gmac_clkin" };
+PNAME(mux_mac2phy_src_p) = { "clk_mac2phy_src",
+ "phy_50m_out" };
+
+static struct rockchip_pll_clock rk3328_pll_clks[] __initdata = {
+ [apll] = PLL(pll_rk3328, PLL_APLL, "apll", mux_pll_p,
+ 0, RK3328_PLL_CON(0),
+ RK3328_MODE_CON, 0, 4, 0, rk3328_pll_frac_rates),
+ [dpll] = PLL(pll_rk3328, PLL_DPLL, "dpll", mux_pll_p,
+ 0, RK3328_PLL_CON(8),
+ RK3328_MODE_CON, 4, 3, 0, NULL),
+ [cpll] = PLL(pll_rk3328, PLL_CPLL, "cpll", mux_pll_p,
+ 0, RK3328_PLL_CON(16),
+ RK3328_MODE_CON, 8, 2, 0, rk3328_pll_rates),
+ [gpll] = PLL(pll_rk3328, PLL_GPLL, "gpll", mux_pll_p,
+ 0, RK3328_PLL_CON(24),
+ RK3328_MODE_CON, 12, 1, 0, rk3328_pll_frac_rates),
+ [npll] = PLL(pll_rk3328, PLL_NPLL, "npll", mux_pll_p,
+ 0, RK3328_PLL_CON(40),
+ RK3328_MODE_CON, 1, 0, 0, rk3328_pll_rates),
+};
+
+#define MFLAGS CLK_MUX_HIWORD_MASK
+#define DFLAGS CLK_DIVIDER_HIWORD_MASK
+#define GFLAGS (CLK_GATE_HIWORD_MASK | CLK_GATE_SET_TO_DISABLE)
+
+static struct rockchip_clk_branch rk3328_i2s0_fracmux __initdata =
+ MUX(0, "i2s0_pre", mux_i2s0_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(6), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_i2s1_fracmux __initdata =
+ MUX(0, "i2s1_pre", mux_i2s1_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(8), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_i2s2_fracmux __initdata =
+ MUX(0, "i2s2_pre", mux_i2s2_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(10), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_spdif_fracmux __initdata =
+ MUX(SCLK_SPDIF, "sclk_spdif", mux_spdif_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(12), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_uart0_fracmux __initdata =
+ MUX(SCLK_UART0, "sclk_uart0", mux_uart0_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(14), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_uart1_fracmux __initdata =
+ MUX(SCLK_UART1, "sclk_uart1", mux_uart1_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(16), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_uart2_fracmux __initdata =
+ MUX(SCLK_UART2, "sclk_uart2", mux_uart2_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(18), 8, 2, MFLAGS);
+
+static struct rockchip_clk_branch rk3328_clk_branches[] __initdata = {
+ /*
+ * Clock-Architecture Diagram 1
+ */
+
+ DIV(0, "clk_24m", "xin24m", CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(2), 8, 5, DFLAGS),
+ COMPOSITE(SCLK_RTC32K, "clk_rtc32k", mux_2plls_xin24m_p, 0,
+ RK3328_CLKSEL_CON(38), 14, 2, MFLAGS, 0, 14, DFLAGS,
+ RK3328_CLKGATE_CON(0), 11, GFLAGS),
+
+ /* PD_MISC */
+ MUX(HDMIPHY, "hdmiphy", mux_hdmiphy_p, CLK_SET_RATE_PARENT,
+ RK3328_MISC_CON, 13, 1, MFLAGS),
+ MUX(USB480M, "usb480m", mux_usb480m_p, CLK_SET_RATE_PARENT,
+ RK3328_MISC_CON, 15, 1, MFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 2
+ */
+
+ /* PD_CORE */
+ GATE(0, "apll_core", "apll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(0), 0, GFLAGS),
+ GATE(0, "gpll_core", "gpll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(0), 2, GFLAGS),
+ GATE(0, "dpll_core", "dpll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(0), 1, GFLAGS),
+ GATE(0, "npll_core", "npll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(0), 12, GFLAGS),
+ COMPOSITE_NOMUX(0, "pclk_dbg", "armclk", CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(1), 0, 4, DFLAGS | CLK_DIVIDER_READ_ONLY,
+ RK3328_CLKGATE_CON(7), 0, GFLAGS),
+ COMPOSITE_NOMUX(0, "aclk_core", "armclk", CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(1), 4, 3, DFLAGS | CLK_DIVIDER_READ_ONLY,
+ RK3328_CLKGATE_CON(7), 1, GFLAGS),
+ GATE(0, "aclk_core_niu", "aclk_core", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(13), 0, GFLAGS),
+ GATE(0, "aclk_gic400", "aclk_core", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(13), 1, GFLAGS),
+
+ GATE(0, "clk_jtag", "jtag_clkin", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(7), 2, GFLAGS),
+
+ /* PD_GPU */
+ COMPOSITE(0, "aclk_gpu_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(44), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 6, GFLAGS),
+ GATE(ACLK_GPU, "aclk_gpu", "aclk_gpu_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(14), 0, GFLAGS),
+ GATE(0, "aclk_gpu_niu", "aclk_gpu_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(14), 1, GFLAGS),
+
+ /* PD_DDR */
+ COMPOSITE(0, "clk_ddr", mux_ddrphy_p, CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(3), 8, 2, MFLAGS, 0, 3, DFLAGS | CLK_DIVIDER_POWER_OF_TWO,
+ RK3328_CLKGATE_CON(0), 4, GFLAGS),
+ GATE(0, "clk_ddrmsch", "clk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 6, GFLAGS),
+ GATE(0, "clk_ddrupctl", "clk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 5, GFLAGS),
+ GATE(0, "aclk_ddrupctl", "clk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 4, GFLAGS),
+ GATE(0, "clk_ddrmon", "xin24m", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(0), 6, GFLAGS),
+
+ COMPOSITE(PCLK_DDR, "pclk_ddr", mux_2plls_hdmiphy_p, 0,
+ RK3328_CLKSEL_CON(4), 13, 2, MFLAGS, 8, 3, DFLAGS,
+ RK3328_CLKGATE_CON(7), 4, GFLAGS),
+ GATE(0, "pclk_ddrupctl", "pclk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 1, GFLAGS),
+ GATE(0, "pclk_ddr_msch", "pclk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 2, GFLAGS),
+ GATE(0, "pclk_ddr_mon", "pclk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 3, GFLAGS),
+ GATE(0, "pclk_ddrstdby", "pclk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 7, GFLAGS),
+ GATE(0, "pclk_ddr_grf", "pclk_ddr", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(18), 9, GFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 3
+ */
+
+ /* PD_BUS */
+ COMPOSITE(ACLK_BUS_PRE, "aclk_bus_pre", mux_2plls_hdmiphy_p, 0,
+ RK3328_CLKSEL_CON(0), 13, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(8), 0, GFLAGS),
+ COMPOSITE_NOMUX(HCLK_BUS_PRE, "hclk_bus_pre", "aclk_bus_pre", 0,
+ RK3328_CLKSEL_CON(1), 8, 2, DFLAGS,
+ RK3328_CLKGATE_CON(8), 1, GFLAGS),
+ COMPOSITE_NOMUX(PCLK_BUS_PRE, "pclk_bus_pre", "aclk_bus_pre", 0,
+ RK3328_CLKSEL_CON(1), 12, 3, DFLAGS,
+ RK3328_CLKGATE_CON(8), 2, GFLAGS),
+ GATE(0, "pclk_bus", "pclk_bus_pre", 0,
+ RK3328_CLKGATE_CON(8), 3, GFLAGS),
+ GATE(0, "pclk_phy_pre", "pclk_bus_pre", 0,
+ RK3328_CLKGATE_CON(8), 4, GFLAGS),
+
+ COMPOSITE(SCLK_TSP, "clk_tsp", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(21), 15, 1, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(2), 5, GFLAGS),
+ GATE(0, "clk_hsadc_tsp", "ext_gpio3a2", 0,
+ RK3328_CLKGATE_CON(17), 13, GFLAGS),
+
+ /* PD_I2S */
+ COMPOSITE(0, "clk_i2s0_div", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(6), 15, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(1), 1, GFLAGS),
+ COMPOSITE_FRACMUX(0, "clk_i2s0_frac", "clk_i2s0_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(7), 0,
+ RK3328_CLKGATE_CON(1), 2, GFLAGS,
+ &rk3328_i2s0_fracmux),
+ GATE(SCLK_I2S0, "clk_i2s0", "i2s0_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(1), 3, GFLAGS),
+
+ COMPOSITE(0, "clk_i2s1_div", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(8), 15, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(1), 4, GFLAGS),
+ COMPOSITE_FRACMUX(0, "clk_i2s1_frac", "clk_i2s1_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(9), 0,
+ RK3328_CLKGATE_CON(1), 5, GFLAGS,
+ &rk3328_i2s1_fracmux),
+ GATE(SCLK_I2S1, "clk_i2s1", "i2s1_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(0), 6, GFLAGS),
+ COMPOSITE_NODIV(SCLK_I2S1_OUT, "i2s1_out", mux_i2s1out_p, 0,
+ RK3328_CLKSEL_CON(8), 12, 1, MFLAGS,
+ RK3328_CLKGATE_CON(1), 7, GFLAGS),
+
+ COMPOSITE(0, "clk_i2s2_div", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(10), 15, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(1), 8, GFLAGS),
+ COMPOSITE_FRACMUX(0, "clk_i2s2_frac", "clk_i2s2_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(11), 0,
+ RK3328_CLKGATE_CON(1), 9, GFLAGS,
+ &rk3328_i2s2_fracmux),
+ GATE(SCLK_I2S2, "clk_i2s2", "i2s2_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(1), 10, GFLAGS),
+ COMPOSITE_NODIV(SCLK_I2S2_OUT, "i2s2_out", mux_i2s2out_p, 0,
+ RK3328_CLKSEL_CON(10), 12, 1, MFLAGS,
+ RK3328_CLKGATE_CON(1), 11, GFLAGS),
+
+ COMPOSITE(0, "clk_spdif_div", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(12), 15, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(1), 12, GFLAGS),
+ COMPOSITE_FRACMUX(0, "clk_spdif_frac", "clk_spdif_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(13), 0,
+ RK3328_CLKGATE_CON(1), 13, GFLAGS,
+ &rk3328_spdif_fracmux),
+
+ /* PD_UART */
+ COMPOSITE(0, "clk_uart0_div", mux_2plls_u480m_p, 0,
+ RK3328_CLKSEL_CON(14), 12, 2, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(1), 14, GFLAGS),
+ COMPOSITE(0, "clk_uart1_div", mux_2plls_u480m_p, 0,
+ RK3328_CLKSEL_CON(16), 12, 2, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 0, GFLAGS),
+ COMPOSITE(0, "clk_uart2_div", mux_2plls_u480m_p, 0,
+ RK3328_CLKSEL_CON(18), 12, 2, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 2, GFLAGS),
+ COMPOSITE_FRACMUX(0, "clk_uart0_frac", "clk_uart0_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(15), 0,
+ RK3328_CLKGATE_CON(1), 15, GFLAGS,
+ &rk3328_uart0_fracmux),
+ COMPOSITE_FRACMUX(0, "clk_uart1_frac", "clk_uart1_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(17), 0,
+ RK3328_CLKGATE_CON(2), 1, GFLAGS,
+ &rk3328_uart1_fracmux),
+ COMPOSITE_FRACMUX(0, "clk_uart2_frac", "clk_uart2_div", CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(19), 0,
+ RK3328_CLKGATE_CON(2), 3, GFLAGS,
+ &rk3328_uart2_fracmux),
+
+ /*
+ * Clock-Architecture Diagram 4
+ */
+
+ COMPOSITE(SCLK_I2C0, "clk_i2c0", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(34), 7, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 9, GFLAGS),
+ COMPOSITE(SCLK_I2C1, "clk_i2c1", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(34), 15, 1, MFLAGS, 8, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 10, GFLAGS),
+ COMPOSITE(SCLK_I2C2, "clk_i2c2", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(35), 7, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 11, GFLAGS),
+ COMPOSITE(SCLK_I2C3, "clk_i2c3", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(35), 15, 1, MFLAGS, 8, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 12, GFLAGS),
+ COMPOSITE(SCLK_CRYPTO, "clk_crypto", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(20), 7, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 4, GFLAGS),
+ COMPOSITE_NOMUX(SCLK_TSADC, "clk_tsadc", "clk_24m", 0,
+ RK3328_CLKSEL_CON(22), 0, 10, DFLAGS,
+ RK3328_CLKGATE_CON(2), 6, GFLAGS),
+ COMPOSITE_NOMUX(SCLK_SARADC, "clk_saradc", "clk_24m", 0,
+ RK3328_CLKSEL_CON(23), 0, 10, DFLAGS,
+ RK3328_CLKGATE_CON(2), 14, GFLAGS),
+ COMPOSITE(SCLK_SPI, "clk_spi", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(24), 7, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 7, GFLAGS),
+ COMPOSITE(SCLK_PWM, "clk_pwm", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(24), 15, 1, MFLAGS, 8, 7, DFLAGS,
+ RK3328_CLKGATE_CON(2), 8, GFLAGS),
+ COMPOSITE(SCLK_OTP, "clk_otp", mux_2plls_xin24m_p, 0,
+ RK3328_CLKSEL_CON(4), 6, 2, MFLAGS, 0, 6, DFLAGS,
+ RK3328_CLKGATE_CON(3), 8, GFLAGS),
+ COMPOSITE(SCLK_EFUSE, "clk_efuse", mux_2plls_xin24m_p, 0,
+ RK3328_CLKSEL_CON(5), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(2), 13, GFLAGS),
+ COMPOSITE(SCLK_PDM, "clk_pdm", mux_cpll_gpll_apll_p, CLK_SET_RATE_NO_REPARENT | CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(20), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(2), 15, GFLAGS),
+
+ GATE(SCLK_TIMER0, "sclk_timer0", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 5, GFLAGS),
+ GATE(SCLK_TIMER1, "sclk_timer1", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 6, GFLAGS),
+ GATE(SCLK_TIMER2, "sclk_timer2", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 7, GFLAGS),
+ GATE(SCLK_TIMER3, "sclk_timer3", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 8, GFLAGS),
+ GATE(SCLK_TIMER4, "sclk_timer4", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 9, GFLAGS),
+ GATE(SCLK_TIMER5, "sclk_timer5", "xin24m", 0,
+ RK3328_CLKGATE_CON(8), 10, GFLAGS),
+
+ COMPOSITE(SCLK_WIFI, "clk_wifi", mux_2plls_u480m_p, 0,
+ RK3328_CLKSEL_CON(52), 6, 2, MFLAGS, 0, 6, DFLAGS,
+ RK3328_CLKGATE_CON(0), 10, GFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 5
+ */
+
+ /* PD_VIDEO */
+ COMPOSITE(ACLK_RKVDEC_PRE, "aclk_rkvdec_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(48), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 0, GFLAGS),
+ FACTOR_GATE(HCLK_RKVDEC_PRE, "hclk_rkvdec_pre", "aclk_rkvdec_pre", 0, 1, 4,
+ RK3328_CLKGATE_CON(11), 0, GFLAGS),
+ GATE(ACLK_RKVDEC, "aclk_rkvdec", "aclk_rkvdec_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(24), 0, GFLAGS),
+ GATE(HCLK_RKVDEC, "hclk_rkvdec", "hclk_rkvdec_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(24), 1, GFLAGS),
+ GATE(0, "aclk_rkvdec_niu", "aclk_rkvdec_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(24), 2, GFLAGS),
+ GATE(0, "hclk_rkvdec_niu", "hclk_rkvdec_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(24), 3, GFLAGS),
+
+ COMPOSITE(SCLK_VDEC_CABAC, "sclk_vdec_cabac", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(48), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 1, GFLAGS),
+
+ COMPOSITE(SCLK_VDEC_CORE, "sclk_vdec_core", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(49), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 2, GFLAGS),
+
+ COMPOSITE(ACLK_VPU_PRE, "aclk_vpu_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(50), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 5, GFLAGS),
+ FACTOR_GATE(HCLK_VPU_PRE, "hclk_vpu_pre", "aclk_vpu_pre", 0, 1, 4,
+ RK3328_CLKGATE_CON(11), 8, GFLAGS),
+ GATE(ACLK_VPU, "aclk_vpu", "aclk_vpu_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(23), 0, GFLAGS),
+ GATE(HCLK_VPU, "hclk_vpu", "hclk_vpu_pre", CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(23), 1, GFLAGS),
+ GATE(0, "aclk_vpu_niu", "aclk_vpu_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(23), 2, GFLAGS),
+ GATE(0, "hclk_vpu_niu", "hclk_vpu_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(23), 3, GFLAGS),
+
+ COMPOSITE(ACLK_RKVENC, "aclk_rkvenc", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(51), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 3, GFLAGS),
+ FACTOR_GATE(HCLK_RKVENC, "hclk_rkvenc", "aclk_rkvenc", 0, 1, 4,
+ RK3328_CLKGATE_CON(11), 4, GFLAGS),
+ GATE(0, "aclk_rkvenc_niu", "aclk_rkvenc", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(25), 0, GFLAGS),
+ GATE(0, "hclk_rkvenc_niu", "hclk_rkvenc", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(25), 1, GFLAGS),
+ GATE(ACLK_H265, "aclk_h265", "aclk_rkvenc", 0,
+ RK3328_CLKGATE_CON(25), 0, GFLAGS),
+ GATE(PCLK_H265, "pclk_h265", "hclk_rkvenc", 0,
+ RK3328_CLKGATE_CON(25), 1, GFLAGS),
+ GATE(ACLK_H264, "aclk_h264", "aclk_rkvenc", 0,
+ RK3328_CLKGATE_CON(25), 0, GFLAGS),
+ GATE(HCLK_H264, "hclk_h264", "hclk_rkvenc", 0,
+ RK3328_CLKGATE_CON(25), 1, GFLAGS),
+ GATE(ACLK_AXISRAM, "aclk_axisram", "aclk_rkvenc", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(25), 0, GFLAGS),
+
+ COMPOSITE(SCLK_VENC_CORE, "sclk_venc_core", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(51), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 4, GFLAGS),
+
+ COMPOSITE(SCLK_VENC_DSP, "sclk_venc_dsp", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(52), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(6), 7, GFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 6
+ */
+
+ /* PD_VIO */
+ COMPOSITE(ACLK_VIO_PRE, "aclk_vio_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(37), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(5), 2, GFLAGS),
+ DIV(HCLK_VIO_PRE, "hclk_vio_pre", "aclk_vio_pre", 0,
+ RK3328_CLKSEL_CON(37), 8, 5, DFLAGS),
+
+ COMPOSITE(ACLK_RGA_PRE, "aclk_rga_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(36), 14, 2, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(5), 0, GFLAGS),
+ COMPOSITE(SCLK_RGA, "clk_rga", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(36), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(5), 1, GFLAGS),
+ COMPOSITE(ACLK_VOP_PRE, "aclk_vop_pre", mux_4plls_p, 0,
+ RK3328_CLKSEL_CON(39), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(5), 5, GFLAGS),
+ GATE(0, "clk_hdmi_sfc", "xin24m", 0,
+ RK3328_CLKGATE_CON(5), 4, GFLAGS),
+
+ COMPOSITE_NODIV(0, "clk_cif_src", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(42), 7, 1, MFLAGS,
+ RK3328_CLKGATE_CON(5), 3, GFLAGS),
+ COMPOSITE_NOGATE(SCLK_CIF_OUT, "clk_cif_out", mux_sclk_cif_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(42), 5, 1, MFLAGS, 0, 5, DFLAGS),
+
+ COMPOSITE(DCLK_LCDC_SRC, "dclk_lcdc_src", mux_gpll_cpll_p, 0,
+ RK3328_CLKSEL_CON(40), 0, 1, MFLAGS, 8, 8, DFLAGS,
+ RK3328_CLKGATE_CON(5), 6, GFLAGS),
+ DIV(DCLK_HDMIPHY, "dclk_hdmiphy", "dclk_lcdc_src", 0,
+ RK3328_CLKSEL_CON(40), 3, 3, DFLAGS),
+ MUX(DCLK_LCDC, "dclk_lcdc", mux_dclk_lcdc_p, 0,
+ RK3328_CLKSEL_CON(40), 1, 1, MFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 7
+ */
+
+ /* PD_PERI */
+ GATE(0, "gpll_peri", "gpll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(4), 0, GFLAGS),
+ GATE(0, "cpll_peri", "cpll", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(4), 1, GFLAGS),
+ GATE(0, "hdmiphy_peri", "hdmiphy", CLK_IGNORE_UNUSED,
+ RK3328_CLKGATE_CON(4), 2, GFLAGS),
+ COMPOSITE_NOGATE(ACLK_PERI_PRE, "aclk_peri_pre", mux_aclk_peri_pre_p, 0,
+ RK3328_CLKSEL_CON(28), 6, 2, MFLAGS, 0, 5, DFLAGS),
+ COMPOSITE_NOMUX(PCLK_PERI, "pclk_peri", "aclk_peri_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(29), 0, 2, DFLAGS,
+ RK3328_CLKGATE_CON(10), 2, GFLAGS),
+ COMPOSITE_NOMUX(HCLK_PERI, "hclk_peri", "aclk_peri_pre", CLK_IGNORE_UNUSED,
+ RK3328_CLKSEL_CON(29), 4, 3, DFLAGS,
+ RK3328_CLKGATE_CON(10), 1, GFLAGS),
+ GATE(ACLK_PERI, "aclk_peri", "aclk_peri_pre", CLK_IGNORE_UNUSED | CLK_SET_RATE_PARENT,
+ RK3328_CLKGATE_CON(10), 0, GFLAGS),
+
+ COMPOSITE(SCLK_SDMMC, "clk_sdmmc", mux_2plls_24m_u480m_p, 0,
+ RK3328_CLKSEL_CON(30), 8, 2, MFLAGS, 0, 8, DFLAGS,
+ RK3328_CLKGATE_CON(4), 3, GFLAGS),
+
+ COMPOSITE(SCLK_SDIO, "clk_sdio", mux_2plls_24m_u480m_p, 0,
+ RK3328_CLKSEL_CON(31), 8, 2, MFLAGS, 0, 8, DFLAGS,
+ RK3328_CLKGATE_CON(4), 4, GFLAGS),
+
+ COMPOSITE(SCLK_EMMC, "clk_emmc", mux_2plls_24m_u480m_p, 0,
+ RK3328_CLKSEL_CON(32), 8, 2, MFLAGS, 0, 8, DFLAGS,
+ RK3328_CLKGATE_CON(4), 5, GFLAGS),
+
+ COMPOSITE(SCLK_SDMMC_EXT, "clk_sdmmc_ext", mux_2plls_24m_u480m_p, 0,
+ RK3328_CLKSEL_CON(43), 8, 2, MFLAGS, 0, 8, DFLAGS,
+ RK3328_CLKGATE_CON(4), 10, GFLAGS),
+
+ COMPOSITE(SCLK_REF_USB3OTG_SRC, "clk_ref_usb3otg_src", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(45), 7, 1, MFLAGS, 0, 7, DFLAGS,
+ RK3328_CLKGATE_CON(4), 9, GFLAGS),
+
+ MUX(SCLK_REF_USB3OTG, "clk_ref_usb3otg", mux_ref_usb3otg_src_p, CLK_SET_RATE_PARENT,
+ RK3328_CLKSEL_CON(45), 8, 1, MFLAGS),
+
+ GATE(SCLK_USB3OTG_REF, "clk_usb3otg_ref", "xin24m", 0,
+ RK3328_CLKGATE_CON(4), 7, GFLAGS),
+
+ COMPOSITE(SCLK_USB3OTG_SUSPEND, "clk_usb3otg_suspend", mux_xin24m_32k_p, 0,
+ RK3328_CLKSEL_CON(33), 15, 1, MFLAGS, 0, 10, DFLAGS,
+ RK3328_CLKGATE_CON(4), 8, GFLAGS),
+
+ /*
+ * Clock-Architecture Diagram 8
+ */
+
+ /* PD_GMAC */
+ COMPOSITE(ACLK_GMAC, "aclk_gmac", mux_2plls_hdmiphy_p, 0,
+ RK3328_CLKSEL_CON(35), 6, 2, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(3), 2, GFLAGS),
+ COMPOSITE_NOMUX(PCLK_GMAC, "pclk_gmac", "aclk_gmac", 0,
+ RK3328_CLKSEL_CON(25), 8, 3, DFLAGS,
+ RK3328_CLKGATE_CON(9), 0, GFLAGS),
+
+ COMPOSITE(SCLK_MAC2IO_SRC, "clk_mac2io_src", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(27), 7, 1, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(3), 1, GFLAGS),
+ GATE(SCLK_MAC2IO_REF, "clk_mac2io_ref", "clk_mac2io", 0,
+ RK3328_CLKGATE_CON(9), 7, GFLAGS),
+ GATE(SCLK_MAC2IO_RX, "clk_mac2io_rx", "clk_mac2io", 0,
+ RK3328_CLKGATE_CON(9), 4, GFLAGS),
+ GATE(SCLK_MAC2IO_TX, "clk_mac2io_tx", "clk_mac2io", 0,
+ RK3328_CLKGATE_CON(9), 5, GFLAGS),
+ GATE(SCLK_MAC2IO_REFOUT, "clk_mac2io_refout", "clk_mac2io", 0,
+ RK3328_CLKGATE_CON(9), 6, GFLAGS),
+ COMPOSITE(SCLK_MAC2IO_OUT, "clk_mac2io_out", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(27), 15, 1, MFLAGS, 8, 5, DFLAGS,
+ RK3328_CLKGATE_CON(3), 5, GFLAGS),
+
+ COMPOSITE(SCLK_MAC2PHY_SRC, "clk_mac2phy_src", mux_2plls_p, 0,
+ RK3328_CLKSEL_CON(26), 7, 1, MFLAGS, 0, 5, DFLAGS,
+ RK3328_CLKGATE_CON(3), 0, GFLAGS),
+ GATE(SCLK_MAC2PHY_REF, "clk_mac2phy_ref", "clk_mac2phy", 0,
+ RK3328_CLKGATE_CON(9), 3, GFLAGS),
+ GATE(SCLK_MAC2PHY_RXTX, "clk_mac2phy_rxtx", "clk_mac2phy", 0,
+ RK3328_CLKGATE_CON(9), 1, GFLAGS),
+ COMPOSITE_NOMUX(SCLK_MAC2PHY_OUT, "clk_mac2phy_out", "clk_mac2phy", 0,
+ RK3328_CLKSEL_CON(26), 8, 2, DFLAGS,
+ RK3328_CLKGATE_CON(9), 2, GFLAGS),
+
+ FACTOR(0, "xin12m", "xin24m", 0, 1, 2),
+
+ /*
+ * Clock-Architecture Diagram 9
+ */
+
+ /* PD_VOP */
+ GATE(ACLK_RGA, "aclk_rga", "aclk_rga_pre", 0, RK3328_CLKGATE_CON(21), 10, GFLAGS),
+ GATE(0, "aclk_rga_niu", "aclk_rga_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(22), 3, GFLAGS),
+ GATE(ACLK_VOP, "aclk_vop", "aclk_vop_pre", 0, RK3328_CLKGATE_CON(21), 2, GFLAGS),
+ GATE(0, "aclk_vop_niu", "aclk_vop_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(21), 4, GFLAGS),
+
+ GATE(ACLK_IEP, "aclk_iep", "aclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 6, GFLAGS),
+ GATE(ACLK_CIF, "aclk_cif", "aclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 8, GFLAGS),
+ GATE(ACLK_HDCP, "aclk_hdcp", "aclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 15, GFLAGS),
+ GATE(0, "aclk_vio_niu", "aclk_vio_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(22), 2, GFLAGS),
+
+ GATE(HCLK_VOP, "hclk_vop", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 3, GFLAGS),
+ GATE(0, "hclk_vop_niu", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 5, GFLAGS),
+ GATE(HCLK_IEP, "hclk_iep", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 7, GFLAGS),
+ GATE(HCLK_CIF, "hclk_cif", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 9, GFLAGS),
+ GATE(HCLK_RGA, "hclk_rga", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(21), 11, GFLAGS),
+ GATE(0, "hclk_ahb1tom", "hclk_vio_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(21), 12, GFLAGS),
+ GATE(0, "pclk_vio_h2p", "hclk_vio_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(21), 13, GFLAGS),
+ GATE(0, "hclk_vio_h2p", "hclk_vio_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(21), 14, GFLAGS),
+ GATE(HCLK_HDCP, "hclk_hdcp", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(22), 0, GFLAGS),
+ GATE(HCLK_VIO, "hclk_vio", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(22), 1, GFLAGS),
+ GATE(PCLK_HDMI, "pclk_hdmi", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(22), 4, GFLAGS),
+ GATE(PCLK_HDCP, "pclk_hdcp", "hclk_vio_pre", 0, RK3328_CLKGATE_CON(22), 5, GFLAGS),
+
+ /* PD_PERI */
+ GATE(0, "aclk_peri_noc", "aclk_peri", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(19), 11, GFLAGS),
+ GATE(ACLK_USB3OTG, "aclk_usb3otg", "aclk_peri", 0, RK3328_CLKGATE_CON(19), 4, GFLAGS),
+
+ GATE(HCLK_SDMMC, "hclk_sdmmc", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 0, GFLAGS),
+ GATE(HCLK_SDIO, "hclk_sdio", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 1, GFLAGS),
+ GATE(HCLK_EMMC, "hclk_emmc", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 2, GFLAGS),
+ GATE(HCLK_SDMMC_EXT, "hclk_sdmmc_ext", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 15, GFLAGS),
+ GATE(HCLK_HOST0, "hclk_host0", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 6, GFLAGS),
+ GATE(HCLK_HOST0_ARB, "hclk_host0_arb", "hclk_peri", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(19), 7, GFLAGS),
+ GATE(HCLK_OTG, "hclk_otg", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 8, GFLAGS),
+ GATE(HCLK_OTG_PMU, "hclk_otg_pmu", "hclk_peri", 0, RK3328_CLKGATE_CON(19), 9, GFLAGS),
+ GATE(0, "hclk_peri_niu", "hclk_peri", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(19), 12, GFLAGS),
+ GATE(0, "pclk_peri_niu", "hclk_peri", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(19), 13, GFLAGS),
+
+ /* PD_GMAC */
+ GATE(ACLK_MAC2PHY, "aclk_mac2phy", "aclk_gmac", 0, RK3328_CLKGATE_CON(26), 0, GFLAGS),
+ GATE(ACLK_MAC2IO, "aclk_mac2io", "aclk_gmac", 0, RK3328_CLKGATE_CON(26), 2, GFLAGS),
+ GATE(0, "aclk_gmac_niu", "aclk_gmac", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(26), 4, GFLAGS),
+ GATE(PCLK_MAC2PHY, "pclk_mac2phy", "pclk_gmac", 0, RK3328_CLKGATE_CON(26), 1, GFLAGS),
+ GATE(PCLK_MAC2IO, "pclk_mac2io", "pclk_gmac", 0, RK3328_CLKGATE_CON(26), 3, GFLAGS),
+ GATE(0, "pclk_gmac_niu", "pclk_gmac", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(26), 5, GFLAGS),
+
+ /* PD_BUS */
+ GATE(0, "aclk_bus_niu", "aclk_bus_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 12, GFLAGS),
+ GATE(ACLK_DCF, "aclk_dcf", "aclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 11, GFLAGS),
+ GATE(ACLK_TSP, "aclk_tsp", "aclk_bus_pre", 0, RK3328_CLKGATE_CON(17), 12, GFLAGS),
+ GATE(0, "aclk_intmem", "aclk_bus_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 0, GFLAGS),
+ GATE(ACLK_DMAC, "aclk_dmac_bus", "aclk_bus_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 1, GFLAGS),
+
+ GATE(0, "hclk_rom", "hclk_bus_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 2, GFLAGS),
+ GATE(HCLK_I2S0_8CH, "hclk_i2s0_8ch", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 3, GFLAGS),
+ GATE(HCLK_I2S1_8CH, "hclk_i2s1_8ch", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 4, GFLAGS),
+ GATE(HCLK_I2S2_2CH, "hclk_i2s2_2ch", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 5, GFLAGS),
+ GATE(HCLK_SPDIF_8CH, "hclk_spdif_8ch", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 6, GFLAGS),
+ GATE(HCLK_TSP, "hclk_tsp", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(17), 11, GFLAGS),
+ GATE(HCLK_CRYPTO_MST, "hclk_crypto_mst", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 7, GFLAGS),
+ GATE(HCLK_CRYPTO_SLV, "hclk_crypto_slv", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(15), 8, GFLAGS),
+ GATE(0, "hclk_bus_niu", "hclk_bus_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 13, GFLAGS),
+ GATE(HCLK_PDM, "hclk_pdm", "hclk_bus_pre", 0, RK3328_CLKGATE_CON(28), 0, GFLAGS),
+
+ GATE(0, "pclk_bus_niu", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 14, GFLAGS),
+ GATE(0, "pclk_efuse", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 9, GFLAGS),
+ GATE(0, "pclk_otp", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(28), 4, GFLAGS),
+ GATE(PCLK_I2C0, "pclk_i2c0", "pclk_bus", 0, RK3328_CLKGATE_CON(15), 10, GFLAGS),
+ GATE(PCLK_I2C1, "pclk_i2c1", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 0, GFLAGS),
+ GATE(PCLK_I2C2, "pclk_i2c2", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 1, GFLAGS),
+ GATE(PCLK_I2C3, "pclk_i2c3", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 2, GFLAGS),
+ GATE(PCLK_TIMER, "pclk_timer0", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 3, GFLAGS),
+ GATE(0, "pclk_stimer", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 4, GFLAGS),
+ GATE(PCLK_SPI, "pclk_spi", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 5, GFLAGS),
+ GATE(PCLK_PWM, "pclk_rk_pwm", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 6, GFLAGS),
+ GATE(PCLK_GPIO0, "pclk_gpio0", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 7, GFLAGS),
+ GATE(PCLK_GPIO1, "pclk_gpio1", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 8, GFLAGS),
+ GATE(PCLK_GPIO2, "pclk_gpio2", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 9, GFLAGS),
+ GATE(PCLK_GPIO3, "pclk_gpio3", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 10, GFLAGS),
+ GATE(PCLK_UART0, "pclk_uart0", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 11, GFLAGS),
+ GATE(PCLK_UART1, "pclk_uart1", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 12, GFLAGS),
+ GATE(PCLK_UART2, "pclk_uart2", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 13, GFLAGS),
+ GATE(PCLK_TSADC, "pclk_tsadc", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 14, GFLAGS),
+ GATE(PCLK_DCF, "pclk_dcf", "pclk_bus", 0, RK3328_CLKGATE_CON(16), 15, GFLAGS),
+ GATE(PCLK_GRF, "pclk_grf", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 0, GFLAGS),
+ GATE(0, "pclk_cru", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 4, GFLAGS),
+ GATE(0, "pclk_sgrf", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 6, GFLAGS),
+ GATE(0, "pclk_sim", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 10, GFLAGS),
+ GATE(PCLK_SARADC, "pclk_saradc", "pclk_bus", 0, RK3328_CLKGATE_CON(17), 15, GFLAGS),
+ GATE(0, "pclk_pmu", "pclk_bus", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(28), 3, GFLAGS),
+
+ GATE(PCLK_USB3PHY_OTG, "pclk_usb3phy_otg", "pclk_phy_pre", 0, RK3328_CLKGATE_CON(28), 1, GFLAGS),
+ GATE(PCLK_USB3PHY_PIPE, "pclk_usb3phy_pipe", "pclk_phy_pre", 0, RK3328_CLKGATE_CON(28), 2, GFLAGS),
+ GATE(PCLK_USB3_GRF, "pclk_usb3_grf", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 2, GFLAGS),
+ GATE(PCLK_USB2_GRF, "pclk_usb2_grf", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 14, GFLAGS),
+ GATE(0, "pclk_ddrphy", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 13, GFLAGS),
+ GATE(0, "pclk_acodecphy", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 5, GFLAGS),
+ GATE(PCLK_HDMIPHY, "pclk_hdmiphy", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 7, GFLAGS),
+ GATE(0, "pclk_vdacphy", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(17), 8, GFLAGS),
+ GATE(0, "pclk_phy_niu", "pclk_phy_pre", CLK_IGNORE_UNUSED, RK3328_CLKGATE_CON(15), 15, GFLAGS),
+
+ /* PD_MMC */
+ MMC(SCLK_SDMMC_DRV, "sdmmc_drv", "sclk_sdmmc",
+ RK3328_SDMMC_CON0, 1),
+ MMC(SCLK_SDMMC_SAMPLE, "sdmmc_sample", "sclk_sdmmc",
+ RK3328_SDMMC_CON1, 1),
+
+ MMC(SCLK_SDIO_DRV, "sdio_drv", "sclk_sdio",
+ RK3328_SDIO_CON0, 1),
+ MMC(SCLK_SDIO_SAMPLE, "sdio_sample", "sclk_sdio",
+ RK3328_SDIO_CON1, 1),
+
+ MMC(SCLK_EMMC_DRV, "emmc_drv", "sclk_emmc",
+ RK3328_EMMC_CON0, 1),
+ MMC(SCLK_EMMC_SAMPLE, "emmc_sample", "sclk_emmc",
+ RK3328_EMMC_CON1, 1),
+
+ MMC(SCLK_SDMMC_EXT_DRV, "sdmmc_ext_drv", "sclk_sdmmc_ext",
+ RK3328_SDMMC_EXT_CON0, 1),
+ MMC(SCLK_SDMMC_EXT_SAMPLE, "sdmmc_ext_sample", "sclk_sdmmc_ext",
+ RK3328_SDMMC_EXT_CON1, 1),
+};
+
+static const char *const rk3328_critical_clocks[] __initconst = {
+ "aclk_bus",
+ "pclk_bus",
+ "hclk_bus",
+ "aclk_peri",
+ "hclk_peri",
+ "pclk_peri",
+ "pclk_dbg",
+ "aclk_core_niu",
+ "aclk_gic400",
+ "aclk_intmem",
+ "hclk_rom",
+ "pclk_grf",
+ "pclk_cru",
+ "pclk_sgrf",
+ "pclk_timer0",
+ "clk_timer0",
+ "pclk_ddr_msch",
+ "pclk_ddr_mon",
+ "pclk_ddr_grf",
+ "clk_ddrupctl",
+ "clk_ddrmsch",
+ "hclk_ahb1tom",
+ "clk_jtag",
+ "pclk_ddrphy",
+ "pclk_pmu",
+ "hclk_otg_pmu",
+ "aclk_rga_niu",
+ "pclk_vio_h2p",
+ "hclk_vio_h2p",
+};
+
+static void __init rk3328_clk_init(struct device_node *np)
+{
+ struct rockchip_clk_provider *ctx;
+ void __iomem *reg_base;
+
+ reg_base = of_iomap(np, 0);
+ if (!reg_base) {
+ pr_err("%s: could not map cru region\n", __func__);
+ return;
+ }
+
+ ctx = rockchip_clk_init(np, reg_base, CLK_NR_CLKS);
+ if (IS_ERR(ctx)) {
+ pr_err("%s: rockchip clk init failed\n", __func__);
+ iounmap(reg_base);
+ return;
+ }
+
+ rockchip_clk_register_plls(ctx, rk3328_pll_clks,
+ ARRAY_SIZE(rk3328_pll_clks),
+ RK3328_GRF_SOC_STATUS0);
+ rockchip_clk_register_branches(ctx, rk3328_clk_branches,
+ ARRAY_SIZE(rk3328_clk_branches));
+ rockchip_clk_protect_critical(rk3328_critical_clocks,
+ ARRAY_SIZE(rk3328_critical_clocks));
+
+ rockchip_clk_register_armclk(ctx, ARMCLK, "armclk",
+ mux_armclk_p, ARRAY_SIZE(mux_armclk_p),
+ &rk3328_cpuclk_data, rk3328_cpuclk_rates,
+ ARRAY_SIZE(rk3328_cpuclk_rates));
+
+ rockchip_register_softrst(np, 11, reg_base + RK3328_SOFTRST_CON(0),
+ ROCKCHIP_SOFTRST_HIWORD_MASK);
+
+ rockchip_register_restart_notifier(ctx, RK3328_GLB_SRST_FST, NULL);
+
+ rockchip_clk_of_add_provider(np, ctx);
+}
+
+CLK_OF_DECLARE(rk3328_cru, "rockchip,rk3328-cru", rk3328_clk_init);
diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h
index 06acb7e0911f..1132c54871f0 100644
--- a/drivers/clk/rockchip/clk.h
+++ b/drivers/clk/rockchip/clk.h
@@ -91,6 +91,24 @@
#define RK3288_EMMC_CON0 0x218
#define RK3288_EMMC_CON1 0x21c
+#define RK3328_PLL_CON(x) RK2928_PLL_CON(x)
+#define RK3328_CLKSEL_CON(x) ((x) * 0x4 + 0x100)
+#define RK3328_CLKGATE_CON(x) ((x) * 0x4 + 0x200)
+#define RK3328_GRFCLKSEL_CON(x) ((x) * 0x4 + 0x100)
+#define RK3328_GLB_SRST_FST 0x9c
+#define RK3328_GLB_SRST_SND 0x98
+#define RK3328_SOFTRST_CON(x) ((x) * 0x4 + 0x300)
+#define RK3328_MODE_CON 0x80
+#define RK3328_MISC_CON 0x84
+#define RK3328_SDMMC_CON0 0x380
+#define RK3328_SDMMC_CON1 0x384
+#define RK3328_SDIO_CON0 0x388
+#define RK3328_SDIO_CON1 0x38c
+#define RK3328_EMMC_CON0 0x390
+#define RK3328_EMMC_CON1 0x394
+#define RK3328_SDMMC_EXT_CON0 0x398
+#define RK3328_SDMMC_EXT_CON1 0x39C
+
#define RK3368_PLL_CON(x) RK2928_PLL_CON(x)
#define RK3368_CLKSEL_CON(x) ((x) * 0x4 + 0x100)
#define RK3368_CLKGATE_CON(x) ((x) * 0x4 + 0x200)
--
1.9.1
^ permalink raw reply related
* Re: [1/5] ARM: dts: qcom: apq8064: Add missing scm clock
From: Andy Gross @ 2016-12-29 3:14 UTC (permalink / raw)
To: Bjorn Andersson
Cc: David Brown, Mark Rutland, devicetree, linux-arm-msm,
linux-kernel, Rob Herring, John Stultz, linux-soc,
linux-arm-kernel
In-Reply-To: <20161221114939.19973-1-bjorn.andersson@linaro.org>
On Wed, Dec 21, 2016 at 03:49:35AM -0800, Bjorn Andersson wrote:
> As per the device tree binding the apq8064 scm node requires the core
> clock to be specified, so add this.
>
> Cc: John Stultz <john.stultz@linaro.org>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> arch/arm/boot/dts/qcom-apq8064.dtsi | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
> index 268bd470c865..78bf155a52f3 100644
> --- a/arch/arm/boot/dts/qcom-apq8064.dtsi
> +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
> @@ -303,6 +303,9 @@
> firmware {
> scm {
> compatible = "qcom,scm-apq8064";
> +
> + clocks = <&gcc CE3_CORE_CLK>;
> + clock-names = "core";
Isn't this supposed to be the DFAB clk? The RPM one? I think that's why we let
the clock just fall through optionally before the recent changes that broke
this.
Regards,
Andy
^ permalink raw reply
* Re: [PATCH v3 3/4] dt-bindings: phy: Add support for QMP phy
From: Vivek Gautam @ 2016-12-29 5:05 UTC (permalink / raw)
To: Stephen Boyd
Cc: robh+dt, kishon,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Mark Rutland,
Srinivas Kandagatla, linux-arm-msm-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161228230412.GC17126-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
On Thu, Dec 29, 2016 at 4:34 AM, Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org> wrote:
> On 12/20, Vivek Gautam wrote:
>> +
>> +Example:
>> + pcie_phy: phy@34000 {
>> + compatible = "qcom,msm8996-qmp-pcie-phy";
>> + reg = <0x034000 0x48f>,
>> + <0x035000 0x5bf>,
>> + <0x036000 0x5bf>,
>> + <0x037000 0x5bf>;
>> + /* tx, rx, pcs */
>> + lane-offsets = <0x0 0x200 0x400>;
>> + #phy-cells = <1>;
>> +
>> + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
>> + <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
>> + <&gcc GCC_PCIE_CLKREF_CLK>,
>> + <&gcc GCC_PCIE_0_PIPE_CLK>,
>> + <&gcc GCC_PCIE_1_PIPE_CLK>,
>> + <&gcc GCC_PCIE_2_PIPE_CLK>;
>> + clock-names = "aux", "cfg_ahb", "ref",
>> + "pipe0", "pipe1", "pipe2";
>
> Can we add a #clock-cells = <0> or <1> here given that this is a
> clk provider? We may want to express the clk circular dependency
> between this phy node and GCC via the clocks property at some
> point instead of doing it implicitly via strings in C code.
Sure, will add #clock-cells = <1>.
Although phys like USB and PIPE currently have just the pipe_clk
being controlled by gcc, the UFS phy has tx/rx symbol clocks that
are controlled by gcc but are generated by phy the same way as
pipe_clk.
So, i guess #clock-cells = <1 > makes sense.
Thanks
Vivek
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH v2 1/2] devicetree: add Garmin vendor prefix
From: Matt Ranostay @ 2016-12-29 5:13 UTC (permalink / raw)
To: linux-iio-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: jic23-DgEjT+Ai2ygdnm+yROfE0A, Matt Ranostay, Rob Herring
Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Matt Ranostay <matt-sk+viVC6FLCDq+mSdOJa79kegs52MxvZ@public.gmane.org>
---
Changes from v1:
* switch to stock ticker for Garmin Limited
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 16d3b5e7f5d1..5749bfc5fc5b 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -107,6 +107,7 @@ firefly Firefly
focaltech FocalTech Systems Co.,Ltd
friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd
fsl Freescale Semiconductor
+grmn Garmin Limited
ge General Electric Company
geekbuying GeekBuying
gef GE Fanuc Intelligent Platforms Embedded Systems, Inc.
--
2.10.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v2 2/2] iio: pulsedlight-lidar-lite-v2: add lidar-lite-v3 property
From: Matt Ranostay @ 2016-12-29 5:13 UTC (permalink / raw)
To: linux-iio-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: jic23-DgEjT+Ai2ygdnm+yROfE0A, Matt Ranostay
In-Reply-To: <20161229051306.28547-1-matt-sk+viVC6FLCDq+mSdOJa79kegs52MxvZ@public.gmane.org>
Signed-off-by: Matt Ranostay <matt-sk+viVC6FLCDq+mSdOJa79kegs52MxvZ@public.gmane.org>
---
Changes from v1:
* switch to using Garmin stock ticker
drivers/iio/proximity/pulsedlight-lidar-lite-v2.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/iio/proximity/pulsedlight-lidar-lite-v2.c b/drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
index 1fa9eefa0982..20c16a08c9d9 100644
--- a/drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
+++ b/drivers/iio/proximity/pulsedlight-lidar-lite-v2.c
@@ -326,12 +326,14 @@ static int lidar_remove(struct i2c_client *client)
static const struct i2c_device_id lidar_id[] = {
{"lidar-lite-v2", 0},
+ {"lidar-lite-v3", 0},
{ },
};
MODULE_DEVICE_TABLE(i2c, lidar_id);
static const struct of_device_id lidar_dt_ids[] = {
{ .compatible = "pulsedlight,lidar-lite-v2" },
+ { .compatible = "grmn,lidar-lite-v3" },
{ }
};
MODULE_DEVICE_TABLE(of, lidar_dt_ids);
--
2.10.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH v3 2/4] phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips
From: Vivek Gautam @ 2016-12-29 6:57 UTC (permalink / raw)
To: Stephen Boyd
Cc: robh+dt, kishon, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Mark Rutland, Srinivas Kandagatla,
linux-arm-msm
In-Reply-To: <20161228230150.GB17126@codeaurora.org>
On Thu, Dec 29, 2016 at 4:31 AM, Stephen Boyd <sboyd@codeaurora.org> wrote:
> On 12/20, Vivek Gautam wrote:
>> PHY transceiver driver for QUSB2 phy controller that provides
>> HighSpeed functionality for DWC3 controller present on
>> Qualcomm chipsets.
>>
>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>
> One comment below, but otherwise
>
> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
>
>> +static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
>> +{
>> + struct device *dev = &qphy->phy->dev;
>> + u8 *val;
>> +
>> + /*
>> + * Read efuse register having TUNE2 parameter's high nibble.
>> + * If efuse register shows value as 0x0, or if we fail to find
>> + * a valid efuse register settings, then use default value
>> + * as 0xB for high nibble that we have already set while
>> + * configuring phy.
>> + */
>> + val = nvmem_cell_read(qphy->cell, NULL);
>> + if (IS_ERR(val) || !val[0]) {
>> + dev_dbg(dev, "failed to read a valid hs-tx trim value, %ld\n",
>> + PTR_ERR(val));
>
> If val is 0 PTR_ERR(0) will be junk? I guess that's ok for debug
> print.
May be -EINVAL is better for debug print. Even when val[0]
is 0, val will still be a valid pointer, and so PTR_ERR(val) will
essentially be the pointer casted to long.
Thanks
Vivek
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* Re: [PATCH v3 2/4] phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips
From: Vivek Gautam @ 2016-12-29 7:00 UTC (permalink / raw)
To: Stephen Boyd
Cc: robh+dt, kishon, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Mark Rutland, Srinivas Kandagatla,
linux-arm-msm
In-Reply-To: <CAFp+6iEKzxKJJCH0+riheGzQwWThfENk6yZoUSSeXuPnLyPdhQ@mail.gmail.com>
Hi Stephen,
On Thu, Dec 29, 2016 at 12:27 PM, Vivek Gautam
<vivek.gautam@codeaurora.org> wrote:
> On Thu, Dec 29, 2016 at 4:31 AM, Stephen Boyd <sboyd@codeaurora.org> wrote:
>> On 12/20, Vivek Gautam wrote:
>>> PHY transceiver driver for QUSB2 phy controller that provides
>>> HighSpeed functionality for DWC3 controller present on
>>> Qualcomm chipsets.
>>>
>>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>>
>> One comment below, but otherwise
>>
>> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Thanks for the review.
Best Regards
Vivek
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* Re: [PATCH v3 4/4] phy: qcom-qmp: new qmp phy driver for qcom-chipsets
From: Vivek Gautam @ 2016-12-29 7:39 UTC (permalink / raw)
To: Stephen Boyd
Cc: robh+dt, kishon, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Mark Rutland, Srinivas Kandagatla,
linux-arm-msm
In-Reply-To: <20161228231659.GD17126@codeaurora.org>
Hi Stephen,
On Thu, Dec 29, 2016 at 4:46 AM, Stephen Boyd <sboyd@codeaurora.org> wrote:
> On 12/20, Vivek Gautam wrote:
>> Qualcomm SOCs have QMP phy controller that provides support
>> to a number of controller, viz. PCIe, UFS, and USB.
>> Add a new driver, based on generic phy framework, for this
>> phy controller.
>>
>> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>> Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
>>
>> +
>> +static struct phy *qcom_qmp_phy_xlate(struct device *dev,
>> + struct of_phandle_args *args)
>> +{
>> + struct qcom_qmp_phy *qphy = dev_get_drvdata(dev);
>> + int i;
>> +
>> + if (WARN_ON(args->args[0] >= qphy->cfg->nlanes))
>> + return ERR_PTR(-ENODEV);
>> +
>> + for (i = 0; i < qphy->cfg->nlanes; i++)
>> + /* phys[i]->index */
>> + if (i == args->args[0])
>> + return qphy->phys[i]->phy;
>
> What's the loop for? If args->arg[0] < qphy->cfg->nlanes then we
> should be able to directly index the qphy->phys array with that
> number and return it.
Right, will do that.
>
>> +
>> + return ERR_PTR(-ENODEV);
>> +}
>> +
> [...]
>> +
>> +/*
>> + * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
>> + * controls it. The <s>_pipe_clk coming out of the GCC is requested
>> + * by the PHY driver for its operations.
>> + * We register the <s>_pipe_clksrc here. The gcc driver takes care
>> + * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
>> + * Below picture shows this relationship.
>> + *
>> + * +--------------+
>> + * | PHY block |<<---------------------------------------+
>> + * | | |
>> + * | +-------+ | +-----+ |
>> + * I/P---^-->| PLL |--^--->pipe_clksrc--->| GCC |--->pipe_clk---+
>> + * clk | +-------+ | +-----+
>> + * +--------------+
>
> There are mixed tabs and spaces in this diagram causing
> confusion in my editor. Please make it only spaces so the picture
> comes out correctly.
Sure, will do that.
>
>> + *
>> + */
>> +static int phy_pipe_clk_register(struct qcom_qmp_phy *qphy, int id)
>> +{
>> + char clk_name[MAX_PROP_NAME];
>
> I'm not sure MAX_PROP_NAME is the same as some max clk name but
> ok. We should be able to calculate that the maximum is length of
> usb3_phy_pipe_clk_src for now though?
Yea, i thought of using the same macro, considering that it provides
32 characters :-)
Will rather use the length of usb3_phy_pipe_clk_src for now. May be
#define MAX_CLK_NAME 24
>
>> + struct clk *clk;
>> +
>> + memset(&clk_name, 0, sizeof(clk_name));
>> + switch (qphy->cfg->type) {
>> + case PHY_TYPE_USB3:
>> + snprintf(clk_name, MAX_PROP_NAME, "usb3_phy_pipe_clk_src");
>> + break;
>> + case PHY_TYPE_PCIE:
>> + snprintf(clk_name, MAX_PROP_NAME, "pcie_%d_pipe_clk_src", id);
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + /* controllers using QMP phys use 125MHz pipe clock interface */
>> + clk = clk_register_fixed_rate(qphy->dev, clk_name, NULL, 0, 125000000);
>
> I was hoping you would be able to calculate the actual output
> rate by reading hardware. This is ok too though.
Yea, I too was looking to understand the phy registers needed to
calculate and re-calibrate the pipe clock rate, but couldn't find much
from the IP programming guide. So, I had to fall back to registering
a fixed-rate clock, since we are sure that the pipe clock rate is fixed at
125 MHz for the controllers using pipe interface.
Once we find out the required information, we can as well register clk_ops
for this clock.
> Just please use
> clk_hw_register_fixed_rate() instead. And you'll probably need
> some sort of devm() usage here to handle probe failure, so I
> would probably roll my own and allocate a fixed_rate clk
> structure and set the rate/name directly and then call
> devm_clk_hw_register().
Sure, will do that.
>
>> +
>> + return PTR_ERR_OR_ZERO(clk);
> --
> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
> a Linux Foundation Collaborative Project
Thanks
Vivek
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH 0/4] Use Exynos macros for pinctrl settings
From: Andi Shyti @ 2016-12-29 8:42 UTC (permalink / raw)
To: Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Andi Shyti, Andi Shyti
In-Reply-To: <CGME20161229084221epcas1p4d76b4b30f59734f7eee29aec53b54af3@epcas1p4.samsung.com>
Hi,
This patchset is just a refactoring of the exynos5433 and TM2
pinctrl definitions. Standing to the samsung-pinctrl.txt binding
the Exynos related DTS should use the macros introduced by
commit:
5db7e3bb87df ("pinctrl: dt-bindings: samsung: Add header with
values used for configuration")
Would be nice to see in the future all the PIN related macros in
the same file, as they more or less do the same thing.
Thanks,
Andi
Andi Shyti (4):
pinctrl: dt-bindings: samsung: add drive strength macros for
Exynos5433
ARM64: dts: exynos5433: use macros for pinctrl configuration on
Exynos5433
ARM64: dts: TM2: comply to the samsung pinctrl naming convention
ARM64: dts: exynos5433: remove unused code
arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 373 ++++++++++-----------
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 254 +++++++-------
include/dt-bindings/pinctrl/samsung.h | 6 +
3 files changed, 314 insertions(+), 319 deletions(-)
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH 1/4] pinctrl: dt-bindings: samsung: add drive strength macros for Exynos5433
From: Andi Shyti @ 2016-12-29 8:42 UTC (permalink / raw)
To: Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel,
Andi Shyti, Andi Shyti
In-Reply-To: <20161229084211.20442-1-andi.shyti@samsung.com>
Commit 5db7e3bb87df ("pinctrl: dt-bindings: samsung: Add header with
values used for configuration") has added a header file for defining the
pinctrl values in order to avoid hardcoded settings in the Exynos
DTS related files.
Extend samsung.h to the Exynos5433 for drive strength values
which are strictly related to the particular SoC and may defer
from others.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
---
include/dt-bindings/pinctrl/samsung.h | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/include/dt-bindings/pinctrl/samsung.h b/include/dt-bindings/pinctrl/samsung.h
index 6276eb785e2b..58868313d64b 100644
--- a/include/dt-bindings/pinctrl/samsung.h
+++ b/include/dt-bindings/pinctrl/samsung.h
@@ -45,6 +45,12 @@
#define EXYNOS5420_PIN_DRV_LV3 2
#define EXYNOS5420_PIN_DRV_LV4 3
+/* Drive strengths for Exynos5433 */
+#define EXYNOS5433_PIN_DRV_LV1 0
+#define EXYNOS5433_PIN_DRV_LV2 1
+#define EXYNOS5433_PIN_DRV_LV3 2
+#define EXYNOS5433_PIN_DRV_LV4 3
+
#define EXYNOS_PIN_FUNC_INPUT 0
#define EXYNOS_PIN_FUNC_OUTPUT 1
#define EXYNOS_PIN_FUNC_2 2
--
2.11.0
^ permalink raw reply related
* [PATCH 2/4] ARM64: dts: exynos5433: use macros for pinctrl configuration on Exynos5433
From: Andi Shyti @ 2016-12-29 8:42 UTC (permalink / raw)
To: Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel,
Andi Shyti, Andi Shyti
In-Reply-To: <20161229084211.20442-1-andi.shyti@samsung.com>
Use the macros defined in include/dt-bindings/pinctrl/samsung.h
instead of hardcoded values.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
---
arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 348 +++++++++++----------
1 file changed, 175 insertions(+), 173 deletions(-)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
index ad71247b074f..36da7dce409a 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -12,6 +12,8 @@
* published by the Free Software Foundation.
*/
+#include <dt-bindings/pinctrl/samsung.h>
+
#define PIN_PULL_NONE 0
#define PIN_PULL_DOWN 1
#define PIN_PULL_UP 3
@@ -145,23 +147,23 @@
i2s0_bus: i2s0-bus {
samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3",
"gpz0-4", "gpz0-5", "gpz0-6";
- samsung,pin-function = <2>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pcm0_bus: pcm0-bus {
samsung,pins = "gpz1-0", "gpz1-1", "gpz1-2", "gpz1-3";
- samsung,pin-function = <3>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
uart_aud_bus: uart-aud-bus {
samsung,pins = "gpz1-3", "gpz1-2", "gpz1-1", "gpz1-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
};
@@ -196,16 +198,16 @@
spi2_bus: spi2-bus {
samsung,pins = "gpd5-0", "gpd5-2", "gpd5-3";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c6_bus: hs-i2c6-bus {
samsung,pins = "gpd5-3", "gpd5-2";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
};
@@ -260,141 +262,141 @@
sd0_clk: sd0-clk {
samsung,pins = "gpr0-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_cmd: sd0-cmd {
samsung,pins = "gpr0-1";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_rdqs: sd0-rdqs {
samsung,pins = "gpr0-2";
- samsung,pin-function = <2>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_qrdy: sd0-qrdy {
samsung,pins = "gpr0-3";
- samsung,pin-function = <2>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_bus1: sd0-bus-width1 {
samsung,pins = "gpr1-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_bus4: sd0-bus-width4 {
samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd0_bus8: sd0-bus-width8 {
samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd1_clk: sd1-clk {
samsung,pins = "gpr2-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd1_cmd: sd1-cmd {
samsung,pins = "gpr2-1";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd1_bus1: sd1-bus-width1 {
samsung,pins = "gpr3-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd1_bus4: sd1-bus-width4 {
samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd1_bus8: sd1-bus-width8 {
samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
pcie_bus: pcie_bus {
samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
};
sd2_clk: sd2-clk {
samsung,pins = "gpr4-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd2_cmd: sd2-cmd {
samsung,pins = "gpr4-1";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd2_cd: sd2-cd {
samsung,pins = "gpr4-2";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd2_bus1: sd2-bus-width1 {
samsung,pins = "gpr4-3";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd2_bus4: sd2-bus-width4 {
samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <3>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV4>;
};
sd2_clk_output: sd2-clk-output {
samsung,pins = "gpr4-0";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <2>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV3>;
};
sd2_cmd_output: sd2-cmd-output {
samsung,pins = "gpr4-1";
- samsung,pin-function = <1>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <2>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV3>;
};
};
@@ -419,9 +421,9 @@
hs_i2c4_bus: hs-i2c4-bus {
samsung,pins = "gpj0-1", "gpj0-0";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
};
@@ -564,225 +566,225 @@
hs_i2c8_bus: hs-i2c8-bus {
samsung,pins = "gpb0-1", "gpb0-0";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c9_bus: hs-i2c9-bus {
samsung,pins = "gpb0-3", "gpb0-2";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
i2s1_bus: i2s1-bus {
samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
"gpd4-3", "gpd4-4";
- samsung,pin-function = <2>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pcm1_bus: pcm1-bus {
samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
"gpd4-3", "gpd4-4";
- samsung,pin-function = <3>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
spdif_bus: spdif-bus {
samsung,pins = "gpd4-3", "gpd4-4";
- samsung,pin-function = <4>;
- samsung,pin-pud = <1>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_spi_pin0: fimc-is-spi-pin0 {
samsung,pins = "gpc3-3", "gpc3-2", "gpc3-1", "gpc3-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_spi_pin1: fimc-is-spi-pin1 {
samsung,pins = "gpc3-7", "gpc3-6", "gpc3-5", "gpc3-4";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
uart0_bus: uart0-bus {
samsung,pins = "gpd0-3", "gpd0-2", "gpd0-1", "gpd0-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
};
hs_i2c2_bus: hs-i2c2-bus {
samsung,pins = "gpd0-3", "gpd0-2";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
uart2_bus: uart2-bus {
samsung,pins = "gpd1-5", "gpd1-4";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
};
uart1_bus: uart1-bus {
samsung,pins = "gpd1-3", "gpd1-2", "gpd1-1", "gpd1-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
};
hs_i2c3_bus: hs-i2c3-bus {
samsung,pins = "gpd1-3", "gpd1-2";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c0_bus: hs-i2c0-bus {
samsung,pins = "gpd2-1", "gpd2-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c1_bus: hs-i2c1-bus {
samsung,pins = "gpd2-3", "gpd2-2";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pwm0_out: pwm0-out {
samsung,pins = "gpd2-4";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pwm1_out: pwm1-out {
samsung,pins = "gpd2-5";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pwm2_out: pwm2-out {
samsung,pins = "gpd2-6";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
pwm3_out: pwm3-out {
samsung,pins = "gpd2-7";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
spi1_bus: spi1-bus {
samsung,pins = "gpd6-2", "gpd6-4", "gpd6-5";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c7_bus: hs-i2c7-bus {
samsung,pins = "gpd2-7", "gpd2-6";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
spi0_bus: spi0-bus {
samsung,pins = "gpd8-0", "gpd6-0", "gpd6-1";
- samsung,pin-function = <2>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c10_bus: hs-i2c10-bus {
samsung,pins = "gpg3-1", "gpg3-0";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
hs_i2c11_bus: hs-i2c11-bus {
samsung,pins = "gpg3-3", "gpg3-2";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
spi3_bus: spi3-bus {
samsung,pins = "gpg3-4", "gpg3-6", "gpg3-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
spi4_bus: spi4-bus {
samsung,pins = "gpv7-1", "gpv7-3", "gpv7-4";
- samsung,pin-function = <3>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_uart: fimc-is-uart {
samsung,pins = "gpc1-1", "gpc0-7";
- samsung,pin-function = <3>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch0_i2c: fimc-is-ch0_i2c {
samsung,pins = "gpc2-1", "gpc2-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch0_mclk: fimc-is-ch0_mclk {
samsung,pins = "gpd7-0";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch1_i2c: fimc-is-ch1-i2c {
samsung,pins = "gpc2-3", "gpc2-2";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch1_mclk: fimc-is-ch1-mclk {
samsung,pins = "gpd7-1";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch2_i2c: fimc-is-ch2-i2c {
samsung,pins = "gpc2-5", "gpc2-4";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
fimc_is_ch2_mclk: fimc-is-ch2-mclk {
samsung,pins = "gpd7-2";
- samsung,pin-function = <2>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
};
@@ -797,8 +799,8 @@
hs_i2c5_bus: hs-i2c5-bus {
samsung,pins = "gpj1-1", "gpj1-0";
- samsung,pin-function = <4>;
- samsung,pin-pud = <3>;
- samsung,pin-drv = <0>;
+ samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+ samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_LV1>;
};
};
--
2.11.0
^ permalink raw reply related
* [PATCH 3/4] ARM64: dts: TM2: comply to the samsung pinctrl naming convention
From: Andi Shyti @ 2016-12-29 8:42 UTC (permalink / raw)
To: Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Andi Shyti, Andi Shyti
In-Reply-To: <20161229084211.20442-1-andi.shyti-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
Change the PIN() macro definition so that it can use the macros
from pinctrl/samsung.h header file.
Signed-off-by: Andi Shyti <andi.shyti-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
---
arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 12 +-
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 254 ++++++++++-----------
2 files changed, 133 insertions(+), 133 deletions(-)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
index 36da7dce409a..9afed9fcf7e1 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -27,12 +27,12 @@
#define PIN_OUT 1
#define PIN_FUNC1 2
-#define PIN(_func, _pin, _pull, _drv) \
- _pin { \
- samsung,pins = #_pin; \
- samsung,pin-function = <PIN_ ##_func>; \
- samsung,pin-pud = <PIN_PULL_ ##_pull>; \
- samsung,pin-drv = <PIN_DRV_ ##_drv>; \
+#define PIN(_func, _pin, _pull, _drv) \
+ _pin { \
+ samsung,pins = #_pin; \
+ samsung,pin-function = <EXYNOS_PIN_FUNC_ ##_func>; \
+ samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>; \
+ samsung,pin-drv = <EXYNOS5433_PIN_DRV_ ##_drv>; \
}
&pinctrl_alive {
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index f21bdc2ff834..a2bc8e48eca4 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -742,77 +742,77 @@
pinctrl-0 = <&initial_alive>;
initial_alive: initial-state {
- PIN(IN, gpa0-0, DOWN, LV1);
- PIN(IN, gpa0-1, NONE, LV1);
- PIN(IN, gpa0-2, DOWN, LV1);
- PIN(IN, gpa0-3, NONE, LV1);
- PIN(IN, gpa0-4, NONE, LV1);
- PIN(IN, gpa0-5, DOWN, LV1);
- PIN(IN, gpa0-6, NONE, LV1);
- PIN(IN, gpa0-7, NONE, LV1);
-
- PIN(IN, gpa1-0, UP, LV1);
- PIN(IN, gpa1-1, NONE, LV1);
- PIN(IN, gpa1-2, NONE, LV1);
- PIN(IN, gpa1-3, DOWN, LV1);
- PIN(IN, gpa1-4, DOWN, LV1);
- PIN(IN, gpa1-5, NONE, LV1);
- PIN(IN, gpa1-6, NONE, LV1);
- PIN(IN, gpa1-7, NONE, LV1);
-
- PIN(IN, gpa2-0, NONE, LV1);
- PIN(IN, gpa2-1, NONE, LV1);
- PIN(IN, gpa2-2, NONE, LV1);
- PIN(IN, gpa2-3, DOWN, LV1);
- PIN(IN, gpa2-4, NONE, LV1);
- PIN(IN, gpa2-5, DOWN, LV1);
- PIN(IN, gpa2-6, DOWN, LV1);
- PIN(IN, gpa2-7, NONE, LV1);
-
- PIN(IN, gpa3-0, DOWN, LV1);
- PIN(IN, gpa3-1, DOWN, LV1);
- PIN(IN, gpa3-2, NONE, LV1);
- PIN(IN, gpa3-3, DOWN, LV1);
- PIN(IN, gpa3-4, NONE, LV1);
- PIN(IN, gpa3-5, DOWN, LV1);
- PIN(IN, gpa3-6, DOWN, LV1);
- PIN(IN, gpa3-7, DOWN, LV1);
-
- PIN(IN, gpf1-0, NONE, LV1);
- PIN(IN, gpf1-1, NONE, LV1);
- PIN(IN, gpf1-2, DOWN, LV1);
- PIN(IN, gpf1-4, UP, LV1);
- PIN(OUT, gpf1-5, NONE, LV1);
- PIN(IN, gpf1-6, DOWN, LV1);
- PIN(IN, gpf1-7, DOWN, LV1);
-
- PIN(IN, gpf2-0, DOWN, LV1);
- PIN(IN, gpf2-1, DOWN, LV1);
- PIN(IN, gpf2-2, DOWN, LV1);
- PIN(IN, gpf2-3, DOWN, LV1);
-
- PIN(IN, gpf3-0, DOWN, LV1);
- PIN(IN, gpf3-1, DOWN, LV1);
- PIN(IN, gpf3-2, NONE, LV1);
- PIN(IN, gpf3-3, DOWN, LV1);
-
- PIN(IN, gpf4-0, DOWN, LV1);
- PIN(IN, gpf4-1, DOWN, LV1);
- PIN(IN, gpf4-2, DOWN, LV1);
- PIN(IN, gpf4-3, DOWN, LV1);
- PIN(IN, gpf4-4, DOWN, LV1);
- PIN(IN, gpf4-5, DOWN, LV1);
- PIN(IN, gpf4-6, DOWN, LV1);
- PIN(IN, gpf4-7, DOWN, LV1);
-
- PIN(IN, gpf5-0, DOWN, LV1);
- PIN(IN, gpf5-1, DOWN, LV1);
- PIN(IN, gpf5-2, DOWN, LV1);
- PIN(IN, gpf5-3, DOWN, LV1);
- PIN(OUT, gpf5-4, NONE, LV1);
- PIN(IN, gpf5-5, DOWN, LV1);
- PIN(IN, gpf5-6, DOWN, LV1);
- PIN(IN, gpf5-7, DOWN, LV1);
+ PIN(INPUT, gpa0-0, DOWN, LV1);
+ PIN(INPUT, gpa0-1, NONE, LV1);
+ PIN(INPUT, gpa0-2, DOWN, LV1);
+ PIN(INPUT, gpa0-3, NONE, LV1);
+ PIN(INPUT, gpa0-4, NONE, LV1);
+ PIN(INPUT, gpa0-5, DOWN, LV1);
+ PIN(INPUT, gpa0-6, NONE, LV1);
+ PIN(INPUT, gpa0-7, NONE, LV1);
+
+ PIN(INPUT, gpa1-0, UP, LV1);
+ PIN(INPUT, gpa1-1, NONE, LV1);
+ PIN(INPUT, gpa1-2, NONE, LV1);
+ PIN(INPUT, gpa1-3, DOWN, LV1);
+ PIN(INPUT, gpa1-4, DOWN, LV1);
+ PIN(INPUT, gpa1-5, NONE, LV1);
+ PIN(INPUT, gpa1-6, NONE, LV1);
+ PIN(INPUT, gpa1-7, NONE, LV1);
+
+ PIN(INPUT, gpa2-0, NONE, LV1);
+ PIN(INPUT, gpa2-1, NONE, LV1);
+ PIN(INPUT, gpa2-2, NONE, LV1);
+ PIN(INPUT, gpa2-3, DOWN, LV1);
+ PIN(INPUT, gpa2-4, NONE, LV1);
+ PIN(INPUT, gpa2-5, DOWN, LV1);
+ PIN(INPUT, gpa2-6, DOWN, LV1);
+ PIN(INPUT, gpa2-7, NONE, LV1);
+
+ PIN(INPUT, gpa3-0, DOWN, LV1);
+ PIN(INPUT, gpa3-1, DOWN, LV1);
+ PIN(INPUT, gpa3-2, NONE, LV1);
+ PIN(INPUT, gpa3-3, DOWN, LV1);
+ PIN(INPUT, gpa3-4, NONE, LV1);
+ PIN(INPUT, gpa3-5, DOWN, LV1);
+ PIN(INPUT, gpa3-6, DOWN, LV1);
+ PIN(INPUT, gpa3-7, DOWN, LV1);
+
+ PIN(INPUT, gpf1-0, NONE, LV1);
+ PIN(INPUT, gpf1-1, NONE, LV1);
+ PIN(INPUT, gpf1-2, DOWN, LV1);
+ PIN(INPUT, gpf1-4, UP, LV1);
+ PIN(OUTPUT, gpf1-5, NONE, LV1);
+ PIN(INPUT, gpf1-6, DOWN, LV1);
+ PIN(INPUT, gpf1-7, DOWN, LV1);
+
+ PIN(INPUT, gpf2-0, DOWN, LV1);
+ PIN(INPUT, gpf2-1, DOWN, LV1);
+ PIN(INPUT, gpf2-2, DOWN, LV1);
+ PIN(INPUT, gpf2-3, DOWN, LV1);
+
+ PIN(INPUT, gpf3-0, DOWN, LV1);
+ PIN(INPUT, gpf3-1, DOWN, LV1);
+ PIN(INPUT, gpf3-2, NONE, LV1);
+ PIN(INPUT, gpf3-3, DOWN, LV1);
+
+ PIN(INPUT, gpf4-0, DOWN, LV1);
+ PIN(INPUT, gpf4-1, DOWN, LV1);
+ PIN(INPUT, gpf4-2, DOWN, LV1);
+ PIN(INPUT, gpf4-3, DOWN, LV1);
+ PIN(INPUT, gpf4-4, DOWN, LV1);
+ PIN(INPUT, gpf4-5, DOWN, LV1);
+ PIN(INPUT, gpf4-6, DOWN, LV1);
+ PIN(INPUT, gpf4-7, DOWN, LV1);
+
+ PIN(INPUT, gpf5-0, DOWN, LV1);
+ PIN(INPUT, gpf5-1, DOWN, LV1);
+ PIN(INPUT, gpf5-2, DOWN, LV1);
+ PIN(INPUT, gpf5-3, DOWN, LV1);
+ PIN(OUTPUT, gpf5-4, NONE, LV1);
+ PIN(INPUT, gpf5-5, DOWN, LV1);
+ PIN(INPUT, gpf5-6, DOWN, LV1);
+ PIN(INPUT, gpf5-7, DOWN, LV1);
};
te_irq: te_irq {
@@ -826,8 +826,8 @@
pinctrl-0 = <&initial_cpif>;
initial_cpif: initial-state {
- PIN(IN, gpv6-0, DOWN, LV1);
- PIN(IN, gpv6-1, DOWN, LV1);
+ PIN(INPUT, gpv6-0, DOWN, LV1);
+ PIN(INPUT, gpv6-1, DOWN, LV1);
};
};
@@ -836,9 +836,9 @@
pinctrl-0 = <&initial_ese>;
initial_ese: initial-state {
- PIN(IN, gpj2-0, DOWN, LV1);
- PIN(IN, gpj2-1, DOWN, LV1);
- PIN(IN, gpj2-2, DOWN, LV1);
+ PIN(INPUT, gpj2-0, DOWN, LV1);
+ PIN(INPUT, gpj2-1, DOWN, LV1);
+ PIN(INPUT, gpj2-2, DOWN, LV1);
};
};
@@ -847,11 +847,11 @@
pinctrl-0 = <&initial_fsys>;
initial_fsys: initial-state {
- PIN(IN, gpr3-0, NONE, LV1);
- PIN(IN, gpr3-1, DOWN, LV1);
- PIN(IN, gpr3-2, DOWN, LV1);
- PIN(IN, gpr3-3, DOWN, LV1);
- PIN(IN, gpr3-7, NONE, LV1);
+ PIN(INPUT, gpr3-0, NONE, LV1);
+ PIN(INPUT, gpr3-1, DOWN, LV1);
+ PIN(INPUT, gpr3-2, DOWN, LV1);
+ PIN(INPUT, gpr3-3, DOWN, LV1);
+ PIN(INPUT, gpr3-7, NONE, LV1);
};
};
@@ -860,14 +860,14 @@
pinctrl-0 = <&initial_imem>;
initial_imem: initial-state {
- PIN(IN, gpf0-0, UP, LV1);
- PIN(IN, gpf0-1, UP, LV1);
- PIN(IN, gpf0-2, DOWN, LV1);
- PIN(IN, gpf0-3, UP, LV1);
- PIN(IN, gpf0-4, DOWN, LV1);
- PIN(IN, gpf0-5, NONE, LV1);
- PIN(IN, gpf0-6, DOWN, LV1);
- PIN(IN, gpf0-7, UP, LV1);
+ PIN(INPUT, gpf0-0, UP, LV1);
+ PIN(INPUT, gpf0-1, UP, LV1);
+ PIN(INPUT, gpf0-2, DOWN, LV1);
+ PIN(INPUT, gpf0-3, UP, LV1);
+ PIN(INPUT, gpf0-4, DOWN, LV1);
+ PIN(INPUT, gpf0-5, NONE, LV1);
+ PIN(INPUT, gpf0-6, DOWN, LV1);
+ PIN(INPUT, gpf0-7, UP, LV1);
};
};
@@ -876,7 +876,7 @@
pinctrl-0 = <&initial_nfc>;
initial_nfc: initial-state {
- PIN(IN, gpj0-2, DOWN, LV1);
+ PIN(INPUT, gpj0-2, DOWN, LV1);
};
};
@@ -885,54 +885,54 @@
pinctrl-0 = <&initial_peric>;
initial_peric: initial-state {
- PIN(IN, gpv7-0, DOWN, LV1);
- PIN(IN, gpv7-1, DOWN, LV1);
- PIN(IN, gpv7-2, NONE, LV1);
- PIN(IN, gpv7-3, DOWN, LV1);
- PIN(IN, gpv7-4, DOWN, LV1);
- PIN(IN, gpv7-5, DOWN, LV1);
+ PIN(INPUT, gpv7-0, DOWN, LV1);
+ PIN(INPUT, gpv7-1, DOWN, LV1);
+ PIN(INPUT, gpv7-2, NONE, LV1);
+ PIN(INPUT, gpv7-3, DOWN, LV1);
+ PIN(INPUT, gpv7-4, DOWN, LV1);
+ PIN(INPUT, gpv7-5, DOWN, LV1);
- PIN(IN, gpb0-4, DOWN, LV1);
+ PIN(INPUT, gpb0-4, DOWN, LV1);
- PIN(IN, gpc0-2, DOWN, LV1);
- PIN(IN, gpc0-5, DOWN, LV1);
- PIN(IN, gpc0-7, DOWN, LV1);
+ PIN(INPUT, gpc0-2, DOWN, LV1);
+ PIN(INPUT, gpc0-5, DOWN, LV1);
+ PIN(INPUT, gpc0-7, DOWN, LV1);
- PIN(IN, gpc1-1, DOWN, LV1);
+ PIN(INPUT, gpc1-1, DOWN, LV1);
- PIN(IN, gpc3-4, NONE, LV1);
- PIN(IN, gpc3-5, NONE, LV1);
- PIN(IN, gpc3-6, NONE, LV1);
- PIN(IN, gpc3-7, NONE, LV1);
+ PIN(INPUT, gpc3-4, NONE, LV1);
+ PIN(INPUT, gpc3-5, NONE, LV1);
+ PIN(INPUT, gpc3-6, NONE, LV1);
+ PIN(INPUT, gpc3-7, NONE, LV1);
- PIN(OUT, gpg0-0, NONE, LV1);
- PIN(FUNC1, gpg0-1, DOWN, LV1);
+ PIN(OUTPUT, gpg0-0, NONE, LV1);
+ PIN(2, gpg0-1, DOWN, LV1);
- PIN(IN, gpd2-5, DOWN, LV1);
+ PIN(INPUT, gpd2-5, DOWN, LV1);
- PIN(IN, gpd4-0, NONE, LV1);
- PIN(IN, gpd4-1, DOWN, LV1);
- PIN(IN, gpd4-2, DOWN, LV1);
- PIN(IN, gpd4-3, DOWN, LV1);
- PIN(IN, gpd4-4, DOWN, LV1);
+ PIN(INPUT, gpd4-0, NONE, LV1);
+ PIN(INPUT, gpd4-1, DOWN, LV1);
+ PIN(INPUT, gpd4-2, DOWN, LV1);
+ PIN(INPUT, gpd4-3, DOWN, LV1);
+ PIN(INPUT, gpd4-4, DOWN, LV1);
- PIN(IN, gpd6-3, DOWN, LV1);
+ PIN(INPUT, gpd6-3, DOWN, LV1);
- PIN(IN, gpd8-1, UP, LV1);
+ PIN(INPUT, gpd8-1, UP, LV1);
- PIN(IN, gpg1-0, DOWN, LV1);
- PIN(IN, gpg1-1, DOWN, LV1);
- PIN(IN, gpg1-2, DOWN, LV1);
- PIN(IN, gpg1-3, DOWN, LV1);
- PIN(IN, gpg1-4, DOWN, LV1);
+ PIN(INPUT, gpg1-0, DOWN, LV1);
+ PIN(INPUT, gpg1-1, DOWN, LV1);
+ PIN(INPUT, gpg1-2, DOWN, LV1);
+ PIN(INPUT, gpg1-3, DOWN, LV1);
+ PIN(INPUT, gpg1-4, DOWN, LV1);
- PIN(IN, gpg2-0, DOWN, LV1);
- PIN(IN, gpg2-1, DOWN, LV1);
+ PIN(INPUT, gpg2-0, DOWN, LV1);
+ PIN(INPUT, gpg2-1, DOWN, LV1);
- PIN(IN, gpg3-0, DOWN, LV1);
- PIN(IN, gpg3-1, DOWN, LV1);
- PIN(IN, gpg3-5, DOWN, LV1);
- PIN(IN, gpg3-7, DOWN, LV1);
+ PIN(INPUT, gpg3-0, DOWN, LV1);
+ PIN(INPUT, gpg3-1, DOWN, LV1);
+ PIN(INPUT, gpg3-5, DOWN, LV1);
+ PIN(INPUT, gpg3-7, DOWN, LV1);
};
};
@@ -941,7 +941,7 @@
pinctrl-0 = <&initial_touch>;
initial_touch: initial-state {
- PIN(IN, gpj1-2, DOWN, LV1);
+ PIN(INPUT, gpj1-2, DOWN, LV1);
};
};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 4/4] ARM64: dts: exynos5433: remove unused code
From: Andi Shyti @ 2016-12-29 8:42 UTC (permalink / raw)
To: Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel,
Andi Shyti, Andi Shyti
In-Reply-To: <20161229084211.20442-1-andi.shyti@samsung.com>
Because the pinctrl DTS is using the samsung.h macros, the
previously pin defines are anused. Remove them.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
---
arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 13 -------------
1 file changed, 13 deletions(-)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
index 9afed9fcf7e1..3c821e5c241e 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -14,19 +14,6 @@
#include <dt-bindings/pinctrl/samsung.h>
-#define PIN_PULL_NONE 0
-#define PIN_PULL_DOWN 1
-#define PIN_PULL_UP 3
-
-#define PIN_DRV_LV1 0
-#define PIN_DRV_LV2 2
-#define PIN_DRV_LV3 1
-#define PIN_DRV_LV4 3
-
-#define PIN_IN 0
-#define PIN_OUT 1
-#define PIN_FUNC1 2
-
#define PIN(_func, _pin, _pull, _drv) \
_pin { \
samsung,pins = #_pin; \
--
2.11.0
^ permalink raw reply related
* Re: [PATCH 2/2] cfg80211: reg: support ieee80211-(min|max)-center-freq DT properties
From: Arend van Spriel @ 2016-12-29 8:57 UTC (permalink / raw)
To: Rafał Miłecki
Cc: Kalle Valo,
linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Martin Blumenstingl, Felix Fietkau, Arnd Bergmann,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Rafał Miłecki
In-Reply-To: <CACna6rzJV-UdydKrXTquEzrkCfNXXKsHBrsZGjTJ8F=BSRyUjA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
On 28-12-16 22:30, Rafał Miłecki wrote:
> On 28 December 2016 at 22:28, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>> On 28 December 2016 at 22:07, Arend van Spriel
>> <arend.vanspriel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
>>> On 28-12-16 16:59, Rafał Miłecki wrote:
>>>> From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>
>>>> They allow specifying hardware limitations of supported channels. This
>>>> may be useful for specifying single band devices or devices that support
>>>> only some part of the whole band.
>>>> E.g. some tri-band routers have separated radios for lower and higher
>>>> part of 5 GHz band.
>>>>
>>>> Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>> ---
>>>> net/wireless/reg.c | 34 ++++++++++++++++++++++++++++++++++
>>>> 1 file changed, 34 insertions(+)
>>>>
>>>> diff --git a/net/wireless/reg.c b/net/wireless/reg.c
>>>> index 5dbac37..35ba5c7 100644
>>>> --- a/net/wireless/reg.c
>>>> +++ b/net/wireless/reg.c
>>>> @@ -1123,6 +1123,26 @@ const char *reg_initiator_name(enum nl80211_reg_initiator initiator)
>>>> }
>>>> EXPORT_SYMBOL(reg_initiator_name);
>>>>
>>>> +static bool reg_center_freq_of_valid(struct wiphy *wiphy,
>>>> + struct ieee80211_channel *chan)
>>>> +{
>>>> + struct device_node *np = wiphy_dev(wiphy)->of_node;
>>>> + u32 val;
>>>> +
>>>> + if (!np)
>>>> + return true;
>>>> +
>>>> + if (!of_property_read_u32(np, "ieee80211-min-center-freq", &val) &&
>>>> + chan->center_freq < KHZ_TO_MHZ(val))
>>>> + return false;
>>>> +
>>>> + if (!of_property_read_u32(np, "ieee80211-max-center-freq", &val) &&
>>>> + chan->center_freq > KHZ_TO_MHZ(val))
>>>> + return false;
>>>
>>> I suspect these functions rely on CONFIG_OF. So might not build for
>>> !CONFIG_OF.
>>
>> I compiled it with
>> # CONFIG_OF is not set
>>
>> Can you test it and provide a non-working config if you see a
>> compilation error, please?
>
> include/linux/of.h provides a lot of dummy static inline functions if
> CONFIG_OF is not used (they also allow compiler to drop most of the
> code).
of_propeirty_read_u32 is static inline in of.h calling
of_property_read_u32_array, which has a dummy variant in of.h returning
-ENOSYS so -38. Pretty sure that is not what you want. At least it does
not allow the compiler to drop any code so probably better to do:
if (!IS_ENABLED(CONFIG_OF) || !np)
return true;
So with this patch you change the channel to DISABLED. I am not very
familiar with reg.c so do you know if this is done before or after
calling regulatory notifier in the driver. brcmfmac will enable channels
querying the device upon regulatory notifier call, which may undo the
behavior introduced by your patch.
Regards,
Arend
^ permalink raw reply
* Re: [PATCH 1/4] pinctrl: dt-bindings: samsung: add drive strength macros for Exynos5433
From: Chanwoo Choi @ 2016-12-29 9:17 UTC (permalink / raw)
To: Andi Shyti, Tomasz Figa, Krzysztof Kozlowski, Sylwester Nawrocki,
Rob Herring, Mark Rutland, Catalin Marinas, Will Deacon,
Kukjin Kim, Javier Martinez Canillas
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel,
Andi Shyti
In-Reply-To: <20161229084211.20442-2-andi.shyti@samsung.com>
Hi Andi,
On 2016년 12월 29일 17:42, Andi Shyti wrote:
> Commit 5db7e3bb87df ("pinctrl: dt-bindings: samsung: Add header with
> values used for configuration") has added a header file for defining the
> pinctrl values in order to avoid hardcoded settings in the Exynos
> DTS related files.
>
> Extend samsung.h to the Exynos5433 for drive strength values
> which are strictly related to the particular SoC and may defer
> from others.
>
> Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
> ---
> include/dt-bindings/pinctrl/samsung.h | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/include/dt-bindings/pinctrl/samsung.h b/include/dt-bindings/pinctrl/samsung.h
> index 6276eb785e2b..58868313d64b 100644
> --- a/include/dt-bindings/pinctrl/samsung.h
> +++ b/include/dt-bindings/pinctrl/samsung.h
> @@ -45,6 +45,12 @@
> #define EXYNOS5420_PIN_DRV_LV3 2
> #define EXYNOS5420_PIN_DRV_LV4 3
>
> +/* Drive strengths for Exynos5433 */
> +#define EXYNOS5433_PIN_DRV_LV1 0
> +#define EXYNOS5433_PIN_DRV_LV2 1
> +#define EXYNOS5433_PIN_DRV_LV3 2
> +#define EXYNOS5433_PIN_DRV_LV4 3
Exynos5433 has the same value with EXYNOS5420. So, I'd like you to use the EXYNOS5420_PIN_DRV_LVx instead of separate the definitions.
> +
> #define EXYNOS_PIN_FUNC_INPUT 0
> #define EXYNOS_PIN_FUNC_OUTPUT 1
> #define EXYNOS_PIN_FUNC_2 2
>
--
Regards,
Chanwoo Choi
^ permalink raw reply
* Re: [1/4] pinctrl: dt-bindings: samsung: add drive strength macros for Exynos5433
From: Jaehoon Chung @ 2016-12-29 9:39 UTC (permalink / raw)
To: Andi Shyti, Tomasz Figa, Chanwoo Choi, Krzysztof Kozlowski,
Sylwester Nawrocki, Rob Herring, Mark Rutland, Catalin Marinas,
Will Deacon, Kukjin Kim, Javier Martinez Canillas
Cc: devicetree, linux-arm-kernel, linux-samsung-soc, linux-kernel,
Andi Shyti
In-Reply-To: <20161229084211.20442-2-andi.shyti@samsung.com>
On 12/29/2016 05:42 PM, Andi Shyti wrote:
> Commit 5db7e3bb87df ("pinctrl: dt-bindings: samsung: Add header with
> values used for configuration") has added a header file for defining the
> pinctrl values in order to avoid hardcoded settings in the Exynos
> DTS related files.
>
> Extend samsung.h to the Exynos5433 for drive strength values
> which are strictly related to the particular SoC and may defer
> from others.
>
> Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
> ---
> include/dt-bindings/pinctrl/samsung.h | 6 ++++++
> 1 file changed, 6 insertions(+)
>
> diff --git a/include/dt-bindings/pinctrl/samsung.h b/include/dt-bindings/pinctrl/samsung.h
> index 6276eb785e2b..58868313d64b 100644
> --- a/include/dt-bindings/pinctrl/samsung.h
> +++ b/include/dt-bindings/pinctrl/samsung.h
> @@ -45,6 +45,12 @@
> #define EXYNOS5420_PIN_DRV_LV3 2
> #define EXYNOS5420_PIN_DRV_LV4 3
>
> +/* Drive strengths for Exynos5433 */
> +#define EXYNOS5433_PIN_DRV_LV1 0
> +#define EXYNOS5433_PIN_DRV_LV2 1
> +#define EXYNOS5433_PIN_DRV_LV3 2
> +#define EXYNOS5433_PIN_DRV_LV4 3
Well, i'm not sure..but you needs to compare the other Exynos5 series.
it's difference bit Offset. Did you check it?
I didn't check pinctrl file..if it doesn't apply any exynos5433 pinctrl for drv_strength.
it will work wrong..
Best Regards,
Jaehoon Chung
> +
> #define EXYNOS_PIN_FUNC_INPUT 0
> #define EXYNOS_PIN_FUNC_OUTPUT 1
> #define EXYNOS_PIN_FUNC_2 2
>
>
^ permalink raw reply
* Re: [PATCH 2/2] cfg80211: reg: support ieee80211-(min|max)-center-freq DT properties
From: Rafał Miłecki @ 2016-12-29 9:43 UTC (permalink / raw)
To: Arend van Spriel
Cc: Kalle Valo,
linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Martin Blumenstingl, Felix Fietkau, Arnd Bergmann,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Rafał Miłecki
In-Reply-To: <46007537-835c-90db-a44f-c45c8e2ecaed-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
On 29 December 2016 at 09:57, Arend van Spriel
<arend.vanspriel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
> On 28-12-16 22:30, Rafał Miłecki wrote:
>> On 28 December 2016 at 22:28, Rafał Miłecki <zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>>> On 28 December 2016 at 22:07, Arend van Spriel
>>> <arend.vanspriel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
>>>> On 28-12-16 16:59, Rafał Miłecki wrote:
>>>>> From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>>
>>>>> They allow specifying hardware limitations of supported channels. This
>>>>> may be useful for specifying single band devices or devices that support
>>>>> only some part of the whole band.
>>>>> E.g. some tri-band routers have separated radios for lower and higher
>>>>> part of 5 GHz band.
>>>>>
>>>>> Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>>>>> ---
>>>>> net/wireless/reg.c | 34 ++++++++++++++++++++++++++++++++++
>>>>> 1 file changed, 34 insertions(+)
>>>>>
>>>>> diff --git a/net/wireless/reg.c b/net/wireless/reg.c
>>>>> index 5dbac37..35ba5c7 100644
>>>>> --- a/net/wireless/reg.c
>>>>> +++ b/net/wireless/reg.c
>>>>> @@ -1123,6 +1123,26 @@ const char *reg_initiator_name(enum nl80211_reg_initiator initiator)
>>>>> }
>>>>> EXPORT_SYMBOL(reg_initiator_name);
>>>>>
>>>>> +static bool reg_center_freq_of_valid(struct wiphy *wiphy,
>>>>> + struct ieee80211_channel *chan)
>>>>> +{
>>>>> + struct device_node *np = wiphy_dev(wiphy)->of_node;
>>>>> + u32 val;
>>>>> +
>>>>> + if (!np)
>>>>> + return true;
>>>>> +
>>>>> + if (!of_property_read_u32(np, "ieee80211-min-center-freq", &val) &&
>>>>> + chan->center_freq < KHZ_TO_MHZ(val))
>>>>> + return false;
>>>>> +
>>>>> + if (!of_property_read_u32(np, "ieee80211-max-center-freq", &val) &&
>>>>> + chan->center_freq > KHZ_TO_MHZ(val))
>>>>> + return false;
>>>>
>>>> I suspect these functions rely on CONFIG_OF. So might not build for
>>>> !CONFIG_OF.
>>>
>>> I compiled it with
>>> # CONFIG_OF is not set
>>>
>>> Can you test it and provide a non-working config if you see a
>>> compilation error, please?
>>
>> include/linux/of.h provides a lot of dummy static inline functions if
>> CONFIG_OF is not used (they also allow compiler to drop most of the
>> code).
>
> of_propeirty_read_u32 is static inline in of.h calling
> of_property_read_u32_array, which has a dummy variant in of.h returning
> -ENOSYS so -38. Pretty sure that is not what you want. At least it does
> not allow the compiler to drop any code so probably better to do:
>
> if (!IS_ENABLED(CONFIG_OF) || !np)
> return true;
Please verify that using a compiler. If there is a problem I'll be
happy to work on it, but I need a proof it exists.
If compilers sees a:
if (!-ENOSYS && chan->center_freq < KHZ_TO_MHZ(val))
condition, it's pretty clear it can be dropped. With both conditional
blocks dropped function always returns "true" and... can be dropped.
Let me see if I can convince you with the following test:
$ grep -m 1 CONFIG_OF .config
# CONFIG_OF is not set
$ objdump --syms net/wireless/reg.o | grep -c reg_center_freq_of_valid
0
$ grep -m 1 CONFIG_OF .config
CONFIG_OF=y
$ objdump --syms net/wireless/reg.o | grep -c reg_center_freq_of_valid
1
> So with this patch you change the channel to DISABLED. I am not very
> familiar with reg.c so do you know if this is done before or after
> calling regulatory notifier in the driver. brcmfmac will enable channels
> querying the device upon regulatory notifier call, which may undo the
> behavior introduced by your patch.
I'm not regulatory export, so I hope someone will review this patch.
So far I can say it works for me after trying it on SR400ac with
BCM43602.
ieee80211-min-center-freq = <2437000>;
[ 11.986941] cfg80211: Disabling freq 2412 MHz as it's out of OF limits
[ 12.000466] cfg80211: Disabling freq 2417 MHz as it's out of OF limits
[ 12.013984] cfg80211: Disabling freq 2422 MHz as it's out of OF limits
[ 12.027497] cfg80211: Disabling freq 2427 MHz as it's out of OF limits
[ 12.041012] cfg80211: Disabling freq 2432 MHz as it's out of OF limits
root@lede:/# iw phy phy0 channels
Band 1:
* 2412 MHz [1] (disabled)
* 2417 MHz [2] (disabled)
* 2422 MHz [3] (disabled)
* 2427 MHz [4] (disabled)
* 2432 MHz [5] (disabled)
* 2437 MHz [6]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40- HT40+
* 2442 MHz [7]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40- HT40+
* 2447 MHz [8]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40-
* 2452 MHz [9]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40-
* 2457 MHz [10]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40-
* 2462 MHz [11]
Maximum TX power: 20.0 dBm
Channel widths: 20MHz HT40-
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
--
Rafał
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox