* [PATCH] gpio: pca953x: Add optional reset gpio control
From: Steve Longerbeam @ 2017-01-02 21:07 UTC (permalink / raw)
To: linus.walleij, gnurou, robh+dt, mark.rutland
Cc: linux-gpio, devicetree, linux-kernel, Steve Longerbeam
In-Reply-To: <1483391271-17304-1-git-send-email-steve_longerbeam@mentor.com>
Add optional reset-gpios pin control. If present, de-assert the
specified reset gpio pin to bring the chip out of reset.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
---
Documentation/devicetree/bindings/gpio/gpio-pca953x.txt | 4 ++++
drivers/gpio/gpio-pca953x.c | 11 +++++++++++
2 files changed, 15 insertions(+)
diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
index 08dd15f..da54f4c 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt
@@ -29,6 +29,10 @@ Required properties:
onsemi,pca9654
exar,xra1202
+Optional properties:
+ - reset-gpios: GPIO specification for the RESET input
+
+
Example:
diff --git a/drivers/gpio/gpio-pca953x.c b/drivers/gpio/gpio-pca953x.c
index d5d72d8..ca2ddea 100644
--- a/drivers/gpio/gpio-pca953x.c
+++ b/drivers/gpio/gpio-pca953x.c
@@ -22,6 +22,7 @@
#include <linux/of_platform.h>
#include <linux/acpi.h>
#include <linux/regulator/consumer.h>
+#include <linux/gpio/consumer.h>
#define PCA953X_INPUT 0
#define PCA953X_OUTPUT 1
@@ -754,8 +755,18 @@ static int pca953x_probe(struct i2c_client *client,
invert = pdata->invert;
chip->names = pdata->names;
} else {
+ struct gpio_desc *reset_gpio;
+
chip->gpio_start = -1;
irq_base = 0;
+
+ /* see if we need to de-assert a reset pin */
+ reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(reset_gpio)) {
+ dev_err(&client->dev, "request for reset pin failed\n");
+ return PTR_ERR(reset_gpio);
+ }
}
chip->client = client;
--
2.7.4
^ permalink raw reply related
* Re: [PATCH 00/20] i.MX Media Driver
From: Fabio Estevam @ 2017-01-02 21:09 UTC (permalink / raw)
To: Steve Longerbeam, Hans Verkuil
Cc: Mark Rutland, Alexandre Courbot, devel, Philipp Zabel,
devicetree@vger.kernel.org, Greg Kroah-Hartman, Linus Walleij,
Russell King - ARM Linux, linux-kernel, Steve Longerbeam,
robh+dt@kernel.org, Sascha Hauer, linux-gpio@vger.kernel.org,
Fabio Estevam, mchehab, Shawn Guo,
linux-arm-kernel@lists.infradead.org, linux-media
In-Reply-To: <1483050455-10683-1-git-send-email-steve_longerbeam@mentor.com>
Hi Steve,
On Thu, Dec 29, 2016 at 8:27 PM, Steve Longerbeam <slongerbeam@gmail.com> wrote:
> This is a media driver for video capture on i.MX.
>
> Refer to Documentation/media/v4l-drivers/imx.rst for example capture
> pipelines on SabreSD, SabreAuto, and SabreLite reference platforms.
>
> This patchset includes the OF graph layout as proposed by Philipp Zabel,
> with only minor changes which are enumerated in the patch header.
Patches 13, 14 and 19 miss your Signed-off-by tag.
Tested the whole series on a mx6qsabresd:
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
^ permalink raw reply
* Re: [PATCH v6 8/9] dt-bindings: mux-adg792a: document devicetree bindings for ADG792A/G mux
From: Jonathan Cameron @ 2017-01-02 21:13 UTC (permalink / raw)
To: Peter Rosin, Jonathan Cameron, linux-kernel
Cc: Wolfram Sang, Rob Herring, Mark Rutland, Hartmut Knaack,
Lars-Peter Clausen, Peter Meerwald-Stadler, Jonathan Corbet,
Arnd Bergmann, Greg Kroah-Hartman, linux-i2c, devicetree,
linux-iio, linux-doc
In-Reply-To: <cdb3b543-979d-69cc-fb7d-a1d968a75056@axentia.se>
On 2 January 2017 20:47:58 GMT+00:00, Peter Rosin <peda@axentia.se> wrote:
>On 2017-01-02 19:05, Jonathan Cameron wrote:
>> On 02/01/17 16:01, Peter Rosin wrote:
>>> On 2017-01-01 12:00, Jonathan Cameron wrote:
>>>> On 30/11/16 08:17, Peter Rosin wrote:
>>>>> Analog Devices ADG792A/G is a triple 4:1 mux.
>>>>>
>>>>> Signed-off-by: Peter Rosin <peda@axentia.se>
>>>> Few comments inline. Worth adding anything about the gpio (output
>pins) to
>>>> the binding at this stage as well? Would certainly be nice to
>support
>>>> them.
>>>
>>> I'll add optional properties "gpio-controller;" and "#gpio-cells =
><2>;"
>>> with the usual interpretation in v7 (but no implementation...) Is
>that
>>> enough?
>>>
>>>> Jonathan
>>>>> ---
>>>>> .../devicetree/bindings/misc/mux-adg792a.txt | 64
>++++++++++++++++++++++
>>>>> 1 file changed, 64 insertions(+)
>>>>> create mode 100644
>Documentation/devicetree/bindings/misc/mux-adg792a.txt
>>>>>
>>>>> diff --git
>a/Documentation/devicetree/bindings/misc/mux-adg792a.txt
>b/Documentation/devicetree/bindings/misc/mux-adg792a.txt
>>>>> new file mode 100644
>>>>> index 000000000000..4677f9ab1c55
>>>>> --- /dev/null
>>>>> +++ b/Documentation/devicetree/bindings/misc/mux-adg792a.txt
>>>>> @@ -0,0 +1,64 @@
>>>>> +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers
>>>>> +
>>>>> +Required properties:
>>>>> +- compatible : "adi,adg792a" or "adi,adg792g"
>>>>> +- #mux-control-cells : <0> if parallel, or <1> if not.
>>>>> +* Standard mux-controller bindings as decribed in
>mux-controller.txt
>>>>> +
>>>>> +Optional properties:
>>>>> +- adi,parallel : if present, the three muxes are bound together
>with a single
>>>>> + mux controller, controlling all three muxes in parallel.
>>>>> +- adi,idle-state : if present, array of states the three mux
>controllers will
>>>>> + have when idle (or, if parallel, a single idle-state).
>>>> Hmm. These are actually a policy decision. As only one policy will
>make
>>>> sense for a given set of hardware probably fine to have it in here
>I guess.
>>>> Might be worth adding a note to say this though.
>>>
>>> I don't really know what you want me to add, do you have a
>suggestion for the
>>> wording?
>>>
>>>>> +
>>>>> +Mux controller states 0 through 3 correspond to signals A through
>D in the
>>>>> +datasheet. Mux controller states 4 and 5 are only available as
>possible idle
>>>>> +states. State 4 represents that nothing is connected, and state 5
>represents
>>>>> +that the mux controller keeps the mux in its previously selected
>state during
>>>>> +the idle period. State 5 is the default idle state.
>>>> I'm never a great fan of magic numbers. Can we represent this more
>cleanly by
>>>> breaking it into multiple properties?
>>>> Optional:
>>>> adi,idle-switch-to-channel : switch to this channel when idle.
>>>> adi,idle-high-impedance : <boolean> the nothing connected state?
>>>>
>>>> If neither present leaves it in previous state?
>>>
>>> It's not that easy. adi,idle-state is an array when there are three
>single
>>> pole quadruple throw muxes, so there really needs to be a number for
>each
>>> desired idle-behavior. Unless you have a better idea for how to
>describe
>>> that?
>> The above with arrays for each of the two parameters?
>> Though then you need a priority documented - I'd say high impedance
>overrides
>> the channel selection if both are present.
>
>How would you specify that the first mux should idle in "state 5", the
>second
>should idle in "state 4" and the third in "state 0"? (original state
>numbering)
>
>You'd still need a magic number for the default idle state (state 5) so
>that
>you can skip entries in the arrays. Or am I missing something?
Ah I had missed state 5. Hmm would need explicit control for that as well. Not nice...
Perhaps 3 state control (magic number but with channel nums separate)
Idle-state array of <switchtostate, currentstate, highimpedance>
Idle-state array of states to switch to if so set?
Slight nicer than a mess of the two things perhaps?
>
>Cheers,
>peda
>
>>>
>>> Cheers,
>>> peda
>>>
>>>>> +
>>>>> +Example:
>>>>> +
>>>>> + /* three independent mux controllers (of which one is used) */
>>>>> + &i2c0 {
>>>>> + mux: adg792a@50 {
>>>>> + compatible = "adi,adg792a";
>>>>> + reg = <0x50>;
>>>>> + #mux-control-cells = <1>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + adc-mux {
>>>>> + compatible = "iio-mux";
>>>>> + io-channels = <&adc 0>;
>>>>> + io-channel-names = "parent";
>>>>> +
>>>>> + mux-controls = <&mux 1>;
>>>>> +
>>>>> + channels = "sync-1", "", "out";
>>>>> + };
>>>>> +
>>>>> +
>>>>> + /*
>>>>> + * Three parallel muxes with one mux controller, useful e.g. if
>>>>> + * the adc is differential, thus needing two signals to be muxed
>>>>> + * simultaneously for correct operation.
>>>>> + */
>>>>> + &i2c0 {
>>>>> + pmux: adg792a@50 {
>>>>> + compatible = "adi,adg792a";
>>>>> + reg = <0x50>;
>>>>> + #mux-control-cells = <0>;
>>>>> + adi,parallel;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + diff-adc-mux {
>>>>> + compatible = "iio-mux";
>>>>> + io-channels = <&adc 0>;
>>>>> + io-channel-names = "parent";
>>>>> +
>>>>> + mux-controls = <&pmux>;
>>>>> +
>>>>> + channels = "sync-1", "", "out";
>>>>> + };
>>>>>
>>>>
>>>
>>
>
>--
>To unsubscribe from this list: send the line "unsubscribe linux-iio" in
>the body of a message to majordomo@vger.kernel.org
>More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
^ permalink raw reply
* Re: [PATCH 2/2] iio: misc: add support for GPIO power switches
From: Linus Walleij @ 2017-01-02 21:53 UTC (permalink / raw)
To: Jonathan Cameron
Cc: Sebastian Reichel, Bartosz Golaszewski, Hartmut Knaack,
Lars-Peter Clausen, Peter Meerwald-Stadler, Rob Herring,
Mark Rutland, linux-iio@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Kevin Hilman, Patrick Titiano, Neil Armstrong, Alexandre Courbot,
linux-gpio@vger.kernel.org, linux-pm@vger.kernel.org, Mark Brown,
Liam
In-Reply-To: <0c3511be-6a3c-f65c-c562-1c4b9318acb1@kernel.org>
On Fri, Dec 30, 2016 at 4:15 PM, Jonathan Cameron <jic23@kernel.org> wrote:
> On 30/12/16 13:05, Linus Walleij wrote:
>> So this needs to be re-architected to either describe the remote system
>> in DT and handle it in the kernel, or handle it all from userspace if it
>> is a one-off non-product thing.
>
> I'm not sure this is always true (though it might be here). There is always
> a need to describe the edge of the known world. Be it that we have
> an accelerometer - ultimately we could describe the device generating the
> acceleration but we have no way of knowing what it is or what it will do..
>
> What we have here is a rather simple case, but what about an I/O bank on
> a PLC. Obviously we can handle that as a bunch of GPIOs but if we know
> more about it we should have means to describe that. Say we know they are
> always driving relays, we should be able to describe that additional known
> stuff. Relays have characteristics such as bounce times etc that if described
> would allow us to do the relevant filtering on inputs to handle this.
>
> Here the fact it is a power supply switch should be describable. Hard to
> get right in a generic way though so in cases like this perhaps you
> are right and it should just be left undescribed and handled in userspace.
>
> Anyhow, here I think leaving it as a gpio interface is probably the way to
> go, but I'm not sure that will always be the case.
No you are right. We are at the fuzzy system perimeter.
For GPIO we currently only have asserted/unasserted, polarity
of that, open drain/source and debounce time. But we will need the whole
slew of pin control settings in the future: drive strength, schmitt-trigger
hysteresis etc etc. And if there is a further component beyond that it
may need a driver in turn even if it is "only" a relay.
Let's see about this one...
Yours,
Linus Walleij
^ permalink raw reply
* Re: [PATCH V2 1/3] cfg80211: allow passing struct device in the wiphy_new call
From: kbuild test robot @ 2017-01-02 22:10 UTC (permalink / raw)
To: Rafał Miłecki
Cc: kbuild-all-JC7UmRfGjtg, Johannes Berg,
linux-wireless-u79uwXL29TY76Z2rM5mHXA, Martin Blumenstingl,
Felix Fietkau, Arend van Spriel, Arnd Bergmann,
devicetree-u79uwXL29TY76Z2rM5mHXA, Rafał Miłecki
In-Reply-To: <20170102132747.3491-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 5168 bytes --]
Hi Rafał,
[auto build test WARNING on mac80211-next/master]
[also build test WARNING on v4.10-rc2 next-20161224]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Rafa-Mi-ecki/cfg80211-allow-passing-struct-device-in-the-wiphy_new-call/20170103-014525
base: https://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next.git master
reproduce: make htmldocs
All warnings (new ones prefixed by >>):
make[3]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
>> include/net/cfg80211.h:3734: warning: No description found for parameter 'dev'
include/net/cfg80211.h:3751: warning: No description found for parameter 'dev'
vim +/dev +3734 include/net/cfg80211.h
3718
3719 /**
3720 * wiphy_new_nm - create a new wiphy for use with cfg80211
3721 *
3722 * @ops: The configuration operations for this device
3723 * @sizeof_priv: The size of the private area to allocate
3724 * @requested_name: Request a particular name.
3725 * NULL is valid value, and means use the default phy%d naming.
3726 *
3727 * Create a new wiphy and associate the given operations with it.
3728 * @sizeof_priv bytes are allocated for private use.
3729 *
3730 * Return: A pointer to the new wiphy. This pointer must be
3731 * assigned to each netdev's ieee80211_ptr for proper operation.
3732 */
3733 struct wiphy *wiphy_new_nm(struct device *dev, const struct cfg80211_ops *ops,
> 3734 int sizeof_priv, const char *requested_name);
3735
3736 /**
3737 * wiphy_new - create a new wiphy for use with cfg80211
3738 *
3739 * @ops: The configuration operations for this device
3740 * @sizeof_priv: The size of the private area to allocate
3741 *
3742 * Create a new wiphy and associate the given operations with it.
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 6421 bytes --]
^ permalink raw reply
* Re: [PATCH 2/2] pinctrl: Introduce TI IOdelay configuration driver
From: Tony Lindgren @ 2017-01-02 22:12 UTC (permalink / raw)
To: Linus Walleij
Cc: Gary Bisson, Grygorii Strashko, Mark Rutland, Nishanth Menon,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
linux-omap-u79uwXL29TY76Z2rM5mHXA, Lokesh Vutla
In-Reply-To: <20161230183732.5595-3-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
* Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org> [161230 10:38]:
> +static struct pinctrl_ops ti_iodelay_pinctrl_ops = {
> + .get_groups_count = pinctrl_generic_get_group_count,
> + .get_group_name = pinctrl_generic_get_group_name,
> + .get_group_pins = pinctrl_generic_get_group_pins,
> + .pin_dbg_show = ti_iodelay_pin_dbg_show,
> + .dt_node_to_map = ti_iodelay_dt_node_to_map,
> +};
> +
> +static struct pinconf_ops ti_iodelay_pinctrl_pinconf_ops = {
> + .pin_config_group_get = ti_iodelay_pinconf_group_get,
> + .pin_config_group_set = ti_iodelay_pinconf_group_set,
> +#ifdef CONFIG_DEBUG_FS
> + .pin_config_group_dbg_show = ti_iodelay_pinconf_group_dbg_show,
> +#endif
I noticed that .pin_dbg_show above needs ifdef CONFIG_DEBUGFS.
Updated patch below.
Regards,
Tony
8< --------------------
>From tony Mon Sep 17 00:00:00 2001
From: Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>
Date: Tue, 27 Dec 2016 08:03:43 -0800
Subject: [PATCH] pinctrl: Introduce TI IOdelay configuration driver
SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.
With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.
It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).
NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.
Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.
In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.
IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.
This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm-l0cyMroinI0@public.gmane.org>
Signed-off-by: Lokesh Vutla <lokeshvutla-l0cyMroinI0@public.gmane.org>
[tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org: updated to use generic pinctrl functions, added
binding documentation, updated comments]
Signed-off-by: Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
---
.../devicetree/bindings/pinctrl/ti,iodelay.txt | 47 +
drivers/pinctrl/Kconfig | 1 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/ti/Kconfig | 10 +
drivers/pinctrl/ti/Makefile | 1 +
drivers/pinctrl/ti/pinctrl-ti-iodelay.c | 947 +++++++++++++++++++++
6 files changed, 1007 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt
create mode 100644 drivers/pinctrl/ti/Kconfig
create mode 100644 drivers/pinctrl/ti/Makefile
create mode 100644 drivers/pinctrl/ti/pinctrl-ti-iodelay.c
diff --git a/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt
new file mode 100644
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/ti,iodelay.txt
@@ -0,0 +1,47 @@
+* Pin configuration for TI IODELAY controller
+
+TI dra7 based SoCs such as am57xx have a controller for setting the IO delay
+for each pin. For most part the IO delay values are programmed by the bootloader,
+but some pins need to be configured dynamically by the kernel such as the
+MMC pins.
+
+Required Properties:
+
+ - compatible: Must be "ti,dra7-iodelay"
+ - reg: Base address and length of the memory resource used
+ - #address-cells: Number of address cells
+ - #size-cells: Size of cells
+ - #pinctrl-cells: Number of pinctrl cells, must be 2. See also
+ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+Example
+-------
+
+In the SoC specific dtsi file:
+
+ dra7_iodelay_core: padconf@4844a000 {
+ compatible = "ti,dra7-iodelay";
+ reg = <0x4844a000 0x0d1c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pinctrl-cells = <2>;
+ };
+
+In board-specific file:
+
+&dra7_iodelay_core {
+ mmc2_iodelay_3v3_conf: mmc2_iodelay_3v3_conf {
+ pinctrl-pin-array = <
+ 0x18c A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A19_IN */
+ 0x1a4 A_DELAY_PS(265) G_DELAY_PS(360) /* CFG_GPMC_A20_IN */
+ 0x1b0 A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A21_IN */
+ 0x1bc A_DELAY_PS(0) G_DELAY_PS(120) /* CFG_GPMC_A22_IN */
+ 0x1c8 A_DELAY_PS(287) G_DELAY_PS(420) /* CFG_GPMC_A23_IN */
+ 0x1d4 A_DELAY_PS(144) G_DELAY_PS(240) /* CFG_GPMC_A24_IN */
+ 0x1e0 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_A25_IN */
+ 0x1ec A_DELAY_PS(120) G_DELAY_PS(0) /* CFG_GPMC_A26_IN */
+ 0x1f8 A_DELAY_PS(120) G_DELAY_PS(180) /* CFG_GPMC_A27_IN */
+ 0x360 A_DELAY_PS(0) G_DELAY_PS(0) /* CFG_GPMC_CS1_IN */
+ >;
+ };
+};
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -300,6 +300,7 @@ source "drivers/pinctrl/spear/Kconfig"
source "drivers/pinctrl/stm32/Kconfig"
source "drivers/pinctrl/sunxi/Kconfig"
source "drivers/pinctrl/tegra/Kconfig"
+source "drivers/pinctrl/ti/Kconfig"
source "drivers/pinctrl/uniphier/Kconfig"
source "drivers/pinctrl/vt8500/Kconfig"
source "drivers/pinctrl/mediatek/Kconfig"
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_PINCTRL_SH_PFC) += sh-pfc/
obj-$(CONFIG_PINCTRL_SPEAR) += spear/
obj-$(CONFIG_PINCTRL_STM32) += stm32/
obj-$(CONFIG_PINCTRL_SUNXI) += sunxi/
+obj-y += ti/
obj-$(CONFIG_PINCTRL_UNIPHIER) += uniphier/
obj-$(CONFIG_ARCH_VT8500) += vt8500/
obj-$(CONFIG_PINCTRL_MTK) += mediatek/
diff --git a/drivers/pinctrl/ti/Kconfig b/drivers/pinctrl/ti/Kconfig
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/Kconfig
@@ -0,0 +1,10 @@
+config PINCTRL_TI_IODELAY
+ tristate "TI IODelay Module pinconf driver"
+ depends on OF
+ select GENERIC_PINCTRL_GROUPS
+ select GENERIC_PINMUX_FUNCTIONS
+ select GENERIC_PINCONF
+ select REGMAP_MMIO
+ help
+ Say Y here to support Texas Instruments' IO delay pinconf driver.
+ IO delay module is used for the DRA7 SoC family.
diff --git a/drivers/pinctrl/ti/Makefile b/drivers/pinctrl/ti/Makefile
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_PINCTRL_TI_IODELAY) += pinctrl-ti-iodelay.o
diff --git a/drivers/pinctrl/ti/pinctrl-ti-iodelay.c b/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
new file mode 100644
--- /dev/null
+++ b/drivers/pinctrl/ti/pinctrl-ti-iodelay.c
@@ -0,0 +1,947 @@
+/*
+ * Support for configuration of IO Delay module found on Texas Instruments SoCs
+ * such as DRA7
+ *
+ * Copyright (C) 2015 Texas Instruments, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include "../core.h"
+#include "../devicetree.h"
+
+#define DRIVER_NAME "ti-iodelay"
+
+/**
+ * struct ti_iodelay_reg_data - Describes the registers for the iodelay instance
+ * @signature_mask: CONFIG_REG mask for the signature bits (see TRM)
+ * @signature_value: CONFIG_REG signature value to be written (see TRM)
+ * @lock_mask: CONFIG_REG mask for the lock bits (see TRM)
+ * @lock_val: CONFIG_REG lock value for the lock bits (see TRM)
+ * @unlock_val:CONFIG_REG unlock value for the lock bits (see TRM)
+ * @binary_data_coarse_mask: CONFIG_REG coarse mask (see TRM)
+ * @binary_data_fine_mask: CONFIG_REG fine mask (see TRM)
+ * @reg_refclk_offset: Refclk register offset
+ * @refclk_period_mask: Refclk mask
+ * @reg_coarse_offset: Coarse register configuration offset
+ * @coarse_delay_count_mask: Coarse delay count mask
+ * @coarse_ref_count_mask: Coarse ref count mask
+ * @reg_fine_offset: Fine register configuration offset
+ * @fine_delay_count_mask: Fine delay count mask
+ * @fine_ref_count_mask: Fine ref count mask
+ * @reg_global_lock_offset: Global iodelay module lock register offset
+ * @global_lock_mask: Lock mask
+ * @global_unlock_val: Unlock value
+ * @global_lock_val: Lock value
+ * @reg_start_offset: Offset to iodelay registers after the CONFIG_REG_0 to 8
+ * @reg_nr_per_pin: Number of iodelay registers for each pin
+ * @regmap_config: Regmap configuration for the IODelay region
+ */
+struct ti_iodelay_reg_data {
+ u32 signature_mask;
+ u32 signature_value;
+ u32 lock_mask;
+ u32 lock_val;
+ u32 unlock_val;
+ u32 binary_data_coarse_mask;
+ u32 binary_data_fine_mask;
+
+ u32 reg_refclk_offset;
+ u32 refclk_period_mask;
+
+ u32 reg_coarse_offset;
+ u32 coarse_delay_count_mask;
+ u32 coarse_ref_count_mask;
+
+ u32 reg_fine_offset;
+ u32 fine_delay_count_mask;
+ u32 fine_ref_count_mask;
+
+ u32 reg_global_lock_offset;
+ u32 global_lock_mask;
+ u32 global_unlock_val;
+ u32 global_lock_val;
+
+ u32 reg_start_offset;
+ u32 reg_nr_per_pin;
+
+ struct regmap_config *regmap_config;
+};
+
+/**
+ * struct ti_iodelay_reg_values - Computed io_reg configuration values (see TRM)
+ * @coarse_ref_count: Coarse reference count
+ * @coarse_delay_count: Coarse delay count
+ * @fine_ref_count: Fine reference count
+ * @fine_delay_count: Fine Delay count
+ * @ref_clk_period: Reference Clock period
+ * @cdpe: Coarse delay parameter
+ * @fdpe: Fine delay parameter
+ */
+struct ti_iodelay_reg_values {
+ u16 coarse_ref_count;
+ u16 coarse_delay_count;
+
+ u16 fine_ref_count;
+ u16 fine_delay_count;
+
+ u16 ref_clk_period;
+
+ u32 cdpe;
+ u32 fdpe;
+};
+
+/**
+ * struct ti_iodelay_cfg - Description of each configuration parameters
+ * @offset: Configuration register offset
+ * @a_delay: Agnostic Delay (in ps)
+ * @g_delay: Gnostic Delay (in ps)
+ */
+struct ti_iodelay_cfg {
+ u16 offset;
+ u16 a_delay;
+ u16 g_delay;
+};
+
+/**
+ * struct ti_iodelay_pingroup - Structure that describes one group
+ * @name: Name of the group
+ * @map: pinctrl map allocated for the group
+ * @cfg: configuration array for the pin (from dt)
+ * @ncfg: number of configuration values allocated
+ * @config: pinconf "Config" - currently a dummy value
+ */
+struct ti_iodelay_pingroup {
+ struct ti_iodelay_cfg *cfg;
+ int ncfg;
+ unsigned long config;
+};
+
+/**
+ * struct ti_iodelay_device - Represents information for a iodelay instance
+ * @dev: Device pointer
+ * @phys_base: Physical address base of the iodelay device
+ * @reg_base: Virtual address base of the iodelay device
+ * @regmap: Regmap for this iodelay instance
+ * @pctl: Pinctrl device
+ * @desc: pinctrl descriptor for pctl
+ * @pa: pinctrl pin wise description
+ * @names: names of the pins
+ * @reg_data: Register definition data for the IODelay instance
+ * @reg_init_conf_values: Initial configuration values.
+ */
+struct ti_iodelay_device {
+ struct device *dev;
+ unsigned long phys_base;
+ void __iomem *reg_base;
+ struct regmap *regmap;
+
+ struct pinctrl_dev *pctl;
+ struct pinctrl_desc desc;
+ struct pinctrl_pin_desc *pa;
+
+ const struct ti_iodelay_reg_data *reg_data;
+ struct ti_iodelay_reg_values reg_init_conf_values;
+};
+
+/**
+ * ti_iodelay_extract() - extract bits for a field
+ * @val: Register value
+ * @mask: Mask
+ *
+ * Return: extracted value which is appropriately shifted
+ */
+static inline u32 ti_iodelay_extract(u32 val, u32 mask)
+{
+ return (val & mask) >> __ffs(mask);
+}
+
+/**
+ * ti_iodelay_compute_dpe() - Compute equation for delay parameter
+ * @period: Period to use
+ * @ref: Reference Count
+ * @delay: Delay count
+ * @delay_m: Delay multiplier
+ *
+ * Return: Computed delay parameter
+ */
+static inline u32 ti_iodelay_compute_dpe(u16 period, u16 ref, u16 delay,
+ u16 delay_m)
+{
+ u64 m, d;
+
+ /* Handle overflow conditions */
+ m = 10 * (u64)period * (u64)ref;
+ d = 2 * (u64)delay * (u64)delay_m;
+
+ /* Truncate result back to 32 bits */
+ return div64_u64(m, d);
+}
+
+/**
+ * ti_iodelay_pinconf_set() - Configure the pin configuration
+ * @iod: iodelay device
+ * @val: Configuration value
+ *
+ * Update the configuration register as per TRM and lockup once done.
+ * *IMPORTANT NOTE* SoC TRM does recommend doing iodelay programmation only
+ * while in Isolation. But, then, isolation also implies that every pin
+ * on the SoC (including DDR) will be isolated out. The only benefit being
+ * a glitchless configuration, However, the intent of this driver is purely
+ * to support a "glitchy" configuration where applicable.
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_pinconf_set(struct ti_iodelay_device *iod,
+ struct ti_iodelay_cfg *cfg)
+{
+ const struct ti_iodelay_reg_data *reg = iod->reg_data;
+ struct ti_iodelay_reg_values *ival = &iod->reg_init_conf_values;
+ struct device *dev = iod->dev;
+ u32 g_delay_coarse, g_delay_fine;
+ u32 a_delay_coarse, a_delay_fine;
+ u32 c_elements, f_elements;
+ u32 total_delay;
+ u32 reg_mask, reg_val, tmp_val;
+ int r;
+
+ /* NOTE: Truncation is expected in all division below */
+ g_delay_coarse = cfg->g_delay / 920;
+ g_delay_fine = ((cfg->g_delay % 920) * 10) / 60;
+
+ a_delay_coarse = cfg->a_delay / ival->cdpe;
+ a_delay_fine = ((cfg->a_delay % ival->cdpe) * 10) / ival->fdpe;
+
+ c_elements = g_delay_coarse + a_delay_coarse;
+ f_elements = (g_delay_fine + a_delay_fine) / 10;
+
+ if (f_elements > 22) {
+ total_delay = c_elements * ival->cdpe + f_elements * ival->fdpe;
+ c_elements = total_delay / ival->cdpe;
+ f_elements = (total_delay % ival->cdpe) / ival->fdpe;
+ }
+
+ reg_mask = reg->signature_mask;
+ reg_val = reg->signature_value << __ffs(reg->signature_mask);
+
+ reg_mask |= reg->binary_data_coarse_mask;
+ tmp_val = c_elements << __ffs(reg->binary_data_coarse_mask);
+ if (tmp_val & ~reg->binary_data_coarse_mask) {
+ dev_err(dev, "Masking overflow of coarse elements %08x\n",
+ tmp_val);
+ tmp_val &= reg->binary_data_coarse_mask;
+ }
+ reg_val |= tmp_val;
+
+ reg_mask |= reg->binary_data_fine_mask;
+ tmp_val = f_elements << __ffs(reg->binary_data_fine_mask);
+ if (tmp_val & ~reg->binary_data_fine_mask) {
+ dev_err(dev, "Masking overflow of fine elements %08x\n",
+ tmp_val);
+ tmp_val &= reg->binary_data_fine_mask;
+ }
+ reg_val |= tmp_val;
+
+ /*
+ * NOTE: we leave the iodelay values unlocked - this is to work around
+ * situations such as those found with mmc mode change.
+ * However, this leaves open any unwarranted changes to padconf register
+ * impacting iodelay configuration. Use with care!
+ */
+ reg_mask |= reg->lock_mask;
+ reg_val |= reg->unlock_val << __ffs(reg->lock_mask);
+ r = regmap_update_bits(iod->regmap, cfg->offset, reg_mask, reg_val);
+
+ dev_info(dev, "Set reg 0x%x Delay(a: %d g: %d), Elements(C=%d F=%d)0x%x\n",
+ cfg->offset, cfg->a_delay, cfg->g_delay, c_elements,
+ f_elements, reg_val);
+
+ return r;
+}
+
+/**
+ * ti_iodelay_pinconf_init_dev() - Initialize IODelay device
+ * @iod: iodelay device
+ *
+ * Unlocks the iodelay region, computes the common parameters
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_pinconf_init_dev(struct ti_iodelay_device *iod)
+{
+ const struct ti_iodelay_reg_data *reg = iod->reg_data;
+ struct device *dev = iod->dev;
+ struct ti_iodelay_reg_values *ival = &iod->reg_init_conf_values;
+ u32 val;
+ int r;
+
+ /* unlock the iodelay region */
+ r = regmap_update_bits(iod->regmap, reg->reg_global_lock_offset,
+ reg->global_lock_mask, reg->global_unlock_val);
+ if (r)
+ return r;
+
+ /* Read up Recalibration sequence done by bootloader */
+ r = regmap_read(iod->regmap, reg->reg_refclk_offset, &val);
+ if (r)
+ return r;
+ ival->ref_clk_period = ti_iodelay_extract(val, reg->refclk_period_mask);
+ dev_dbg(dev, "refclk_period=0x%04x\n", ival->ref_clk_period);
+
+ r = regmap_read(iod->regmap, reg->reg_coarse_offset, &val);
+ if (r)
+ return r;
+ ival->coarse_ref_count =
+ ti_iodelay_extract(val, reg->coarse_ref_count_mask);
+ ival->coarse_delay_count =
+ ti_iodelay_extract(val, reg->coarse_delay_count_mask);
+ if (!ival->coarse_delay_count) {
+ dev_err(dev, "Invalid Coarse delay count (0) (reg=0x%08x)\n",
+ val);
+ return -EINVAL;
+ }
+ ival->cdpe = ti_iodelay_compute_dpe(ival->ref_clk_period,
+ ival->coarse_ref_count,
+ ival->coarse_delay_count, 88);
+ if (!ival->cdpe) {
+ dev_err(dev, "Invalid cdpe computed params = %d %d %d\n",
+ ival->ref_clk_period, ival->coarse_ref_count,
+ ival->coarse_delay_count);
+ return -EINVAL;
+ }
+ dev_dbg(iod->dev, "coarse: ref=0x%04x delay=0x%04x cdpe=0x%08x\n",
+ ival->coarse_ref_count, ival->coarse_delay_count, ival->cdpe);
+
+ r = regmap_read(iod->regmap, reg->reg_fine_offset, &val);
+ if (r)
+ return r;
+ ival->fine_ref_count =
+ ti_iodelay_extract(val, reg->fine_ref_count_mask);
+ ival->fine_delay_count =
+ ti_iodelay_extract(val, reg->fine_delay_count_mask);
+ if (!ival->fine_delay_count) {
+ dev_err(dev, "Invalid Fine delay count (0) (reg=0x%08x)\n",
+ val);
+ return -EINVAL;
+ }
+ ival->fdpe = ti_iodelay_compute_dpe(ival->ref_clk_period,
+ ival->fine_ref_count,
+ ival->fine_delay_count, 264);
+ if (!ival->fdpe) {
+ dev_err(dev, "Invalid fdpe(0) computed params = %d %d %d\n",
+ ival->ref_clk_period, ival->fine_ref_count,
+ ival->fine_delay_count);
+ return -EINVAL;
+ }
+ dev_dbg(iod->dev, "fine: ref=0x%04x delay=0x%04x fdpe=0x%08x\n",
+ ival->fine_ref_count, ival->fine_delay_count, ival->fdpe);
+
+ return 0;
+}
+
+/**
+ * ti_iodelay_pinconf_deinit_dev() - deinit the iodelay device
+ * @iod: IODelay device
+ *
+ * Deinitialize the IODelay device (basically just lock the region back up.
+ */
+static void ti_iodelay_pinconf_deinit_dev(struct ti_iodelay_device *iod)
+{
+ const struct ti_iodelay_reg_data *reg = iod->reg_data;
+
+ /* lock the iodelay region back again */
+ regmap_update_bits(iod->regmap, reg->reg_global_lock_offset,
+ reg->global_lock_mask, reg->global_lock_val);
+}
+
+/**
+ * ti_iodelay_get_pingroup() - Find the group mapped by a group selector
+ * @iod: iodelay device
+ * @selector: Group Selector
+ *
+ * Return: Corresponding group representing group selector
+ */
+static struct ti_iodelay_pingroup *
+ti_iodelay_get_pingroup(struct ti_iodelay_device *iod, unsigned int selector)
+{
+ struct group_desc *g;
+
+ g = pinctrl_generic_get_group(iod->pctl, selector);
+ if (!g) {
+ dev_err(iod->dev, "%s could not find pingroup %i\n", __func__,
+ selector);
+
+ return NULL;
+ }
+
+ return g->data;
+}
+
+/**
+ * ti_iodelay_offset_to_pin() - get a pin index based on the register offset
+ * @iod: iodelay driver instance
+ * @offset: register offset from the base
+ */
+static int ti_iodelay_offset_to_pin(struct ti_iodelay_device *iod,
+ unsigned int offset)
+{
+ const struct ti_iodelay_reg_data *r = iod->reg_data;
+ unsigned int index;
+
+ if (offset > r->regmap_config->max_register) {
+ dev_err(iod->dev, "mux offset out of range: 0x%x (0x%x)\n",
+ offset, r->regmap_config->max_register);
+ return -EINVAL;
+ }
+
+ index = (offset - r->reg_start_offset) / r->regmap_config->reg_stride;
+ index /= r->reg_nr_per_pin;
+
+ return index;
+}
+
+/**
+ *
+ * @pctldev: Pin controller driver
+ * @np: Device node
+ * @pinctrl_spec: Parsed arguments from device tree
+ * @pins: Array of pins in the pin group
+ * @pin_index: Pin index in the pin array
+ * @data: Pin controller driver specific data
+ *
+ */
+static int ti_iodelay_node_iterator(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ const struct of_phandle_args *pinctrl_spec,
+ int *pins, int pin_index, void *data)
+{
+ struct ti_iodelay_device *iod;
+ struct ti_iodelay_cfg *cfg = data;
+ const struct ti_iodelay_reg_data *r;
+ struct pinctrl_pin_desc *pd;
+ int pin;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ if (!iod)
+ return -EINVAL;
+
+ r = iod->reg_data;
+
+ if (pinctrl_spec->args_count < r->reg_nr_per_pin) {
+ dev_err(iod->dev, "invalid args_count for spec: %i\n",
+ pinctrl_spec->args_count);
+
+ return -EINVAL;
+ }
+
+ /* Index plus two value cells */
+ cfg[pin_index].offset = pinctrl_spec->args[0];
+ cfg[pin_index].a_delay = pinctrl_spec->args[1] & 0xffff;
+ cfg[pin_index].g_delay = pinctrl_spec->args[2] & 0xffff;
+
+ pin = ti_iodelay_offset_to_pin(iod, cfg[pin_index].offset);
+ if (pin < 0) {
+ dev_err(iod->dev, "could not add functions for %s %ux\n",
+ np->name, cfg[pin_index].offset);
+ return -ENODEV;
+ }
+ pins[pin_index] = pin;
+
+ pd = &iod->pa[pin];
+ pd->drv_data = &cfg[pin_index];
+
+ dev_dbg(iod->dev, "%s offset=%x a_delay = %d g_delay = %d\n",
+ np->name, cfg[pin_index].offset, cfg[pin_index].a_delay,
+ cfg[pin_index].g_delay);
+
+ return 0;
+}
+
+/**
+ * ti_iodelay_dt_node_to_map() - Map a device tree node to appropriate group
+ * @pctldev: pinctrl device representing IODelay device
+ * @np: Node Pointer (device tree)
+ * @map: Pinctrl Map returned back to pinctrl framework
+ * @num_maps: Number of maps (1)
+ *
+ * Maps the device tree description into a group of configuration parameters
+ * for iodelay block entry.
+ *
+ * Return: 0 in case of success, else appropriate error value
+ */
+static int ti_iodelay_dt_node_to_map(struct pinctrl_dev *pctldev,
+ struct device_node *np,
+ struct pinctrl_map **map,
+ unsigned int *num_maps)
+{
+ struct ti_iodelay_device *iod;
+ struct ti_iodelay_cfg *cfg;
+ struct ti_iodelay_pingroup *g;
+ const char *name = "pinctrl-pin-array";
+ int rows, *pins, error = -EINVAL, i;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ if (!iod)
+ return -EINVAL;
+
+ rows = pinctrl_count_index_with_args(np, name);
+ if (rows == -EINVAL)
+ return rows;
+
+ *map = devm_kzalloc(iod->dev, sizeof(**map), GFP_KERNEL);
+ if (!*map)
+ return -ENOMEM;
+ *num_maps = 0;
+
+ g = devm_kzalloc(iod->dev, sizeof(*g), GFP_KERNEL);
+ if (!g) {
+ error = -ENOMEM;
+ goto free_map;
+ }
+
+ pins = devm_kzalloc(iod->dev, sizeof(*pins) * rows, GFP_KERNEL);
+ if (!pins)
+ goto free_group;
+
+ cfg = devm_kzalloc(iod->dev, sizeof(*cfg) * rows, GFP_KERNEL);
+ if (!cfg) {
+ error = -ENOMEM;
+ goto free_pins;
+ }
+
+ for (i = 0; i < rows; i++) {
+ struct of_phandle_args pinctrl_spec;
+
+ error = pinctrl_parse_index_with_args(np, name, i,
+ &pinctrl_spec);
+ if (error)
+ goto free_data;
+
+ error = ti_iodelay_node_iterator(pctldev, np, &pinctrl_spec,
+ pins, i, cfg);
+ if (error)
+ goto free_data;
+ }
+
+ g->cfg = cfg;
+ g->ncfg = i;
+ g->config = PIN_CONFIG_END;
+
+ error = pinctrl_generic_add_group(iod->pctl, np->name, pins, i, g);
+ if (error < 0)
+ goto free_data;
+
+ (*map)->type = PIN_MAP_TYPE_CONFIGS_GROUP;
+ (*map)->data.configs.group_or_pin = np->name;
+ (*map)->data.configs.configs = &g->config;
+ (*map)->data.configs.num_configs = 1;
+ *num_maps = 1;
+
+ return 0;
+
+free_data:
+ devm_kfree(iod->dev, cfg);
+free_pins:
+ devm_kfree(iod->dev, pins);
+free_group:
+ devm_kfree(iod->dev, g);
+free_map:
+ devm_kfree(iod->dev, *map);
+
+ return error;
+}
+
+/**
+ * ti_iodelay_pinconf_group_get() - Get the group configuration
+ * @pctldev: pinctrl device representing IODelay device
+ * @selector: Group selector
+ * @config: Configuration returned
+ *
+ * Return: The configuration if the group is valid, else returns -EINVAL
+ */
+static int ti_iodelay_pinconf_group_get(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ unsigned long *config)
+{
+ struct ti_iodelay_device *iod;
+ struct device *dev;
+ struct ti_iodelay_pingroup *group;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ dev = iod->dev;
+ group = ti_iodelay_get_pingroup(iod, selector);
+
+ if (!group)
+ return -EINVAL;
+
+ *config = group->config;
+ return 0;
+}
+
+/**
+ * ti_iodelay_pinconf_group_set() - Configure the groups of pins
+ * @pctldev: pinctrl device representing IODelay device
+ * @selector: Group selector
+ * @configs: Configurations
+ * @num_configs: Number of configurations
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_pinconf_group_set(struct pinctrl_dev *pctldev,
+ unsigned int selector,
+ unsigned long *configs,
+ unsigned int num_configs)
+{
+ struct ti_iodelay_device *iod;
+ struct device *dev;
+ struct ti_iodelay_pingroup *group;
+ int i;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ dev = iod->dev;
+ group = ti_iodelay_get_pingroup(iod, selector);
+
+ if (num_configs != 1) {
+ dev_err(dev, "Unsupported number of configurations %d\n",
+ num_configs);
+ return -EINVAL;
+ }
+
+ if (*configs != PIN_CONFIG_END) {
+ dev_err(dev, "Unsupported configuration\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < group->ncfg; i++) {
+ if (ti_iodelay_pinconf_set(iod, &group->cfg[i]))
+ return -ENOTSUPP;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_DEBUG_FS
+/**
+ * ti_iodelay_pin_to_offset() - get pin register offset based on the pin index
+ * @iod: iodelay driver instance
+ * @selector: Pin index
+ */
+static unsigned int ti_iodelay_pin_to_offset(struct ti_iodelay_device *iod,
+ unsigned int selector)
+{
+ const struct ti_iodelay_reg_data *r = iod->reg_data;
+ unsigned int offset;
+
+ offset = selector * r->regmap_config->reg_stride;
+ offset *= r->reg_nr_per_pin;
+ offset += r->reg_start_offset;
+
+ return offset;
+}
+
+static void ti_iodelay_pin_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s,
+ unsigned int pin)
+{
+ struct ti_iodelay_device *iod;
+ struct pinctrl_pin_desc *pd;
+ struct ti_iodelay_cfg *cfg;
+ const struct ti_iodelay_reg_data *r;
+ unsigned long offset;
+ u32 in, oen, out;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ r = iod->reg_data;
+
+ offset = ti_iodelay_pin_to_offset(iod, pin);
+ if (pin < 0) {
+ dev_err(iod->dev, "invalid pin offset for pin%i\n", pin);
+
+ return;
+ }
+
+ pd = &iod->pa[pin];
+ cfg = pd->drv_data;
+
+ regmap_read(iod->regmap, offset, &in);
+ regmap_read(iod->regmap, offset + r->regmap_config->reg_stride, &oen);
+ regmap_read(iod->regmap, offset + r->regmap_config->reg_stride * 2,
+ &out);
+
+ seq_printf(s, "%lx a: %i g: %i (%08x %08x %08x) %s ",
+ iod->phys_base + offset,
+ cfg ? cfg->a_delay : -1,
+ cfg ? cfg->g_delay : -1,
+ in, oen, out, DRIVER_NAME);
+}
+
+/**
+ * ti_iodelay_pinconf_group_dbg_show() - show the group information
+ * @pctldev: Show the group information
+ * @s: Sequence file
+ * @selector: Group selector
+ *
+ * Provide the configuration information of the selected group
+ */
+static void ti_iodelay_pinconf_group_dbg_show(struct pinctrl_dev *pctldev,
+ struct seq_file *s,
+ unsigned int selector)
+{
+ struct ti_iodelay_device *iod;
+ struct device *dev;
+ struct ti_iodelay_pingroup *group;
+ int i;
+
+ iod = pinctrl_dev_get_drvdata(pctldev);
+ dev = iod->dev;
+ group = ti_iodelay_get_pingroup(iod, selector);
+ if (!group)
+ return;
+
+ for (i = 0; i < group->ncfg; i++) {
+ struct ti_iodelay_cfg *cfg;
+ u32 reg = 0;
+
+ cfg = &group->cfg[i];
+ regmap_read(iod->regmap, cfg->offset, ®),
+ seq_printf(s, "\n\t0x%08x = 0x%08x (%3d, %3d)",
+ cfg->offset, reg, cfg->a_delay,
+ cfg->g_delay);
+ }
+}
+#endif
+
+static struct pinctrl_ops ti_iodelay_pinctrl_ops = {
+ .get_groups_count = pinctrl_generic_get_group_count,
+ .get_group_name = pinctrl_generic_get_group_name,
+ .get_group_pins = pinctrl_generic_get_group_pins,
+#ifdef CONFIG_DEBUG_FS
+ .pin_dbg_show = ti_iodelay_pin_dbg_show,
+#endif
+ .dt_node_to_map = ti_iodelay_dt_node_to_map,
+};
+
+static struct pinconf_ops ti_iodelay_pinctrl_pinconf_ops = {
+ .pin_config_group_get = ti_iodelay_pinconf_group_get,
+ .pin_config_group_set = ti_iodelay_pinconf_group_set,
+#ifdef CONFIG_DEBUG_FS
+ .pin_config_group_dbg_show = ti_iodelay_pinconf_group_dbg_show,
+#endif
+};
+
+/**
+ * ti_iodelay_alloc_pins() - Allocate structures needed for pins for iodelay
+ * @dev: Device pointer
+ * @iod: iodelay device
+ * @base_phy: Base Physical Address
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_alloc_pins(struct device *dev,
+ struct ti_iodelay_device *iod, u32 base_phy)
+{
+ const struct ti_iodelay_reg_data *r = iod->reg_data;
+ struct pinctrl_pin_desc *pin;
+ u32 phy_reg;
+ int nr_pins, i;
+
+ nr_pins = ti_iodelay_offset_to_pin(iod, r->regmap_config->max_register);
+ dev_dbg(dev, "Allocating %i pins\n", nr_pins);
+
+ iod->pa = devm_kzalloc(dev, sizeof(*iod->pa) * nr_pins, GFP_KERNEL);
+ if (!iod->pa)
+ return -ENOMEM;
+
+ iod->desc.pins = iod->pa;
+ iod->desc.npins = nr_pins;
+
+ phy_reg = r->reg_start_offset + base_phy;
+
+ for (i = 0; i < nr_pins; i++, phy_reg += 4) {
+ pin = &iod->pa[i];
+ pin->number = i;
+ }
+
+ return 0;
+}
+
+static struct regmap_config dra7_iodelay_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0xd1c,
+};
+
+static struct ti_iodelay_reg_data dra7_iodelay_data = {
+ .signature_mask = 0x0003f000,
+ .signature_value = 0x29,
+ .lock_mask = 0x00000400,
+ .lock_val = 1,
+ .unlock_val = 0,
+ .binary_data_coarse_mask = 0x000003e0,
+ .binary_data_fine_mask = 0x0000001f,
+
+ .reg_refclk_offset = 0x14,
+ .refclk_period_mask = 0xffff,
+
+ .reg_coarse_offset = 0x18,
+ .coarse_delay_count_mask = 0xffff0000,
+ .coarse_ref_count_mask = 0x0000ffff,
+
+ .reg_fine_offset = 0x1C,
+ .fine_delay_count_mask = 0xffff0000,
+ .fine_ref_count_mask = 0x0000ffff,
+
+ .reg_global_lock_offset = 0x2c,
+ .global_lock_mask = 0x0000ffff,
+ .global_unlock_val = 0x0000aaaa,
+ .global_lock_val = 0x0000aaab,
+
+ .reg_start_offset = 0x30,
+ .reg_nr_per_pin = 3,
+ .regmap_config = &dra7_iodelay_regmap_config,
+};
+
+static const struct of_device_id ti_iodelay_of_match[] = {
+ {.compatible = "ti,dra7-iodelay", .data = &dra7_iodelay_data},
+ { /* Hopefully no more.. */ },
+};
+MODULE_DEVICE_TABLE(of, ti_iodelay_of_match);
+
+/**
+ * ti_iodelay_probe() - Standard probe
+ * @pdev: platform device
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = of_node_get(dev->of_node);
+ const struct of_device_id *match;
+ struct resource *res;
+ struct ti_iodelay_device *iod;
+ int ret = 0;
+
+ if (!np) {
+ ret = -EINVAL;
+ dev_err(dev, "No OF node\n");
+ goto exit_out;
+ }
+
+ match = of_match_device(ti_iodelay_of_match, dev);
+ if (!match) {
+ ret = -EINVAL;
+ dev_err(dev, "No DATA match\n");
+ goto exit_out;
+ }
+
+ iod = devm_kzalloc(dev, sizeof(*iod), GFP_KERNEL);
+ if (!iod) {
+ ret = -ENOMEM;
+ goto exit_out;
+ }
+ iod->dev = dev;
+ iod->reg_data = match->data;
+
+ /* So far We can assume there is only 1 bank of registers */
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(dev, "Missing MEM resource\n");
+ ret = -ENODEV;
+ goto exit_out;
+ }
+
+ iod->phys_base = res->start;
+ iod->reg_base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(iod->reg_base)) {
+ ret = PTR_ERR(iod->reg_base);
+ goto exit_out;
+ }
+
+ iod->regmap = devm_regmap_init_mmio(dev, iod->reg_base,
+ iod->reg_data->regmap_config);
+ if (IS_ERR(iod->regmap)) {
+ dev_err(dev, "Regmap MMIO init failed.\n");
+ ret = PTR_ERR(iod->regmap);
+ goto exit_out;
+ }
+
+ if (ti_iodelay_pinconf_init_dev(iod))
+ goto exit_out;
+
+ ret = ti_iodelay_alloc_pins(dev, iod, res->start);
+ if (ret)
+ goto exit_out;
+
+ iod->desc.pctlops = &ti_iodelay_pinctrl_ops;
+ /* no pinmux ops - we are pinconf */
+ iod->desc.confops = &ti_iodelay_pinctrl_pinconf_ops;
+ iod->desc.name = dev_name(dev);
+ iod->desc.owner = THIS_MODULE;
+
+ iod->pctl = pinctrl_register(&iod->desc, dev, iod);
+ if (!iod->pctl) {
+ dev_err(dev, "Failed to register pinctrl\n");
+ ret = -ENODEV;
+ goto exit_out;
+ }
+
+ platform_set_drvdata(pdev, iod);
+
+exit_out:
+ of_node_put(np);
+ return ret;
+}
+
+/**
+ * ti_iodelay_remove() - standard remove
+ * @pdev: platform device
+ *
+ * Return: 0 if all went fine, else appropriate error value.
+ */
+static int ti_iodelay_remove(struct platform_device *pdev)
+{
+ struct ti_iodelay_device *iod = platform_get_drvdata(pdev);
+
+ if (!iod)
+ return 0;
+
+ if (iod->pctl)
+ pinctrl_unregister(iod->pctl);
+
+ ti_iodelay_pinconf_deinit_dev(iod);
+
+ /* Expect other allocations to be freed by devm */
+
+ return 0;
+}
+
+static struct platform_driver ti_iodelay_driver = {
+ .probe = ti_iodelay_probe,
+ .remove = ti_iodelay_remove,
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = DRIVER_NAME,
+ .of_match_table = ti_iodelay_of_match,
+ },
+};
+module_platform_driver(ti_iodelay_driver);
+
+MODULE_AUTHOR("Texas Instruments, Inc.");
+MODULE_DESCRIPTION("Pinconf driver for TI's IO Delay module");
+MODULE_LICENSE("GPL v2");
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH V3 2/2] cfg80211: support ieee80211-freq-limit DT property
From: Rafał Miłecki @ 2017-01-02 22:12 UTC (permalink / raw)
To: Johannes Berg
Cc: linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Martin Blumenstingl, Felix Fietkau, Arend van Spriel,
Arnd Bergmann, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Rafał Miłecki
In-Reply-To: <1483379548.15591.1.camel-cdvu00un1VgdHxzADdlk8Q@public.gmane.org>
On 2 January 2017 at 18:52, Johannes Berg <johannes-cdvu00un1VgdHxzADdlk8Q@public.gmane.org> wrote:
>> +static void wiphy_freq_limits_apply(struct wiphy *wiphy)
> [...]
>> + if (!wiphy_freq_limits_valid_chan(wiphy,
>> chan)) {
>> + pr_debug("Disabling freq %d MHz as
>> it's out of OF limits\n",
>> + chan->center_freq);
>> + chan->flags |=
>> IEEE80211_CHAN_DISABLED;
>
> I think you didn't address the problem in the best way now.
>
> The problem with the channel sharing was the way you're applying the
> limits - at runtime. This is now OK since the new function shouldn't be
> called when the channel structs are shared, but hooking it all into the
> regulatory code is now no longer needed.
>
> What you can do now, when reading the OF data, is actually apply it to
> the channel flags immediately. If done *before* wiphy_register(), these
> flags will be preserved forever, so you no longer need any hooks in
> regulatory code at all - you can just set the original channel flags
> according to the OF data.
>
> I think this greatly simplifies the flow, since you can also remove
> wiphy->freq_limits (and n_freq_limits) completely, since now the only
> effect of the function would be to modify the channel list, and later
> regulatory updates would always preserve the flags.
I need some extra help understanding this :(
When driver uses custom regulatory it registers initial channels at
init but it can also react to regdom changes using reg_notifier. Is
that correct?
So I'm looking at brcmf_cfg80211_reg_notifier which calls
brcmf_setup_wiphybands which calls brcmf_construct_chaninfo.
That last one reworks all channels on every call. It first marks all
existing channels as DISABLED then queries firmware for the list of
supported channels and updates wiphy channels one by one.
So if I understand this correctly, every regdom change can result in
rebuilding channels pretty much from the scratch. That's why I
believed I need to call wiphy_freq_limits_apply on runtime, not just
during the init.
Is there some flow in my understanding?
--
Rafał
^ permalink raw reply
* Re: [PATCH V3 2/2] cfg80211: support ieee80211-freq-limit DT property
From: Rafał Miłecki @ 2017-01-02 22:16 UTC (permalink / raw)
To: Arend van Spriel
Cc: Johannes Berg,
linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Martin Blumenstingl, Felix Fietkau, Arend van Spriel,
Arnd Bergmann, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Rafał Miłecki
In-Reply-To: <e194b980-1048-8da6-624b-26f824ff655d-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
On 2 January 2017 at 21:12, Arend van Spriel
<arend.vanspriel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
> On 02-01-17 18:52, Johannes Berg wrote:
>>> +static void wiphy_freq_limits_apply(struct wiphy *wiphy)
>> [...]
>>> + if (!wiphy_freq_limits_valid_chan(wiphy,
>>> chan)) {
>>> + pr_debug("Disabling freq %d MHz as
>>> it's out of OF limits\n",
>>> + chan->center_freq);
>>> + chan->flags |=
>>> IEEE80211_CHAN_DISABLED;
>>
>> I think you didn't address the problem in the best way now.
>>
>> The problem with the channel sharing was the way you're applying the
>> limits - at runtime. This is now OK since the new function shouldn't be
>> called when the channel structs are shared, but hooking it all into thes
>> regulatory code is now no longer needed.
>>
>> What you can do now, when reading the OF data, is actually apply it to
>> the channel flags immediately. If done *before* wiphy_register(), these
>> flags will be preserved forever, so you no longer need any hooks in
>> regulatory code at all - you can just set the original channel flags
>> according to the OF data.
>
> I suppose this then can also be done early in the wiphy_register()
> function itself, right?
When driver calls wiphy_apply_custom_regulatory I need to already have
limits read from the DT (at least in my current implementation, it may
change, but I need help understanding flow first). As
wiphy_apply_custom_regulatory has to be called before wiphy_register,
I can't read DT so late (in wiphy_register).
--
Rafał
^ permalink raw reply
* [PATCH 0/5] arm64: sunxi: A64: enable MMC support
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
So far the Allwinner A64/Pine64 DT was missing MMC support, because we
observed issues with that. Those have now been fixed (patch 1 and 2),
so we can enable the MMC IP block in the SoC .dtsi and the Pine64 .dts.
As this gives access to the SD card (as the only mass storage device on
most boards), this makes the kernel support actually useful.
The A64 MMC controller has more up its sleeves, but for now this level
of support is good enough.
Thanks a lot to Maxime for investigating the eMMC failure and coming up
with a nice fix for that.
Maxime: I picked that patch from some pastebin drop of yours, please holler
if there's something wrong with that (patch 2/5).
I send the BananaPi M64 .dts patch along with that series, as the eMMC on
that board now makes some difference.
Cheers,
Andre.
Andre Przywara (4):
drivers: mmc: sunxi: fix A64 calibration routine
arm64: dts: sun50i: add MMC nodes
arm64: dts: Pine64: add MMC support
arm64: dts: add BananaPi-M64 support
Maxime Ripard (1):
drivers: mmc: sunxi: limit A64 MMC2 to 8K DMA buffer
.../devicetree/bindings/mmc/sunxi-mmc.txt | 1 +
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 125 +++++++++++++++++++++
.../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 18 +++
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 77 +++++++++++++
drivers/mmc/host/sunxi-mmc.c | 37 ++++--
6 files changed, 247 insertions(+), 12 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
--
2.8.2
^ permalink raw reply
* [PATCH 1/5] drivers: mmc: sunxi: fix A64 calibration routine
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1483398226-29321-1-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
The calibration facility in the A64 MMC block seems to have been
misunderstood: the result value is not the value to program into the
delay bits, but is the number of delay cells that result in a full clock
cycle delay. So this value has to be scaled by the desired phase, which
we still have to know and program.
Change the calibration routine to take a phase parameter and scale the
calibration value accordingly.
Also introduce sun50i-a64 delay parameters to store the required phase.
Looking at the BSP kernel the sample delay for anything below HS200 is
0, so we go with that value.
Once the driver supports HS200 and faster modes, we can enter confirmed
working values in there.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
---
drivers/mmc/host/sunxi-mmc.c | 30 ++++++++++++++++++------------
1 file changed, 18 insertions(+), 12 deletions(-)
diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
index b1d1303..1e156e8 100644
--- a/drivers/mmc/host/sunxi-mmc.c
+++ b/drivers/mmc/host/sunxi-mmc.c
@@ -681,15 +681,13 @@ static int sunxi_mmc_oclk_onoff(struct sunxi_mmc_host *host, u32 oclk_en)
return 0;
}
-static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off)
+static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off,
+ int degrees)
{
u32 reg = readl(host->reg_base + reg_off);
u32 delay;
unsigned long timeout;
- if (!host->cfg->can_calibrate)
- return 0;
-
reg &= ~(SDXC_CAL_DL_MASK << SDXC_CAL_DL_SW_SHIFT);
reg &= ~SDXC_CAL_DL_SW_EN;
@@ -711,6 +709,7 @@ static int sunxi_mmc_calibrate(struct sunxi_mmc_host *host, int reg_off)
}
delay = (reg >> SDXC_CAL_DL_SHIFT) & SDXC_CAL_DL_MASK;
+ delay = degrees * delay / 360;
reg &= ~SDXC_CAL_START;
reg |= (delay << SDXC_CAL_DL_SW_SHIFT) | SDXC_CAL_DL_SW_EN;
@@ -748,6 +747,11 @@ static int sunxi_mmc_clk_set_phase(struct sunxi_mmc_host *host,
return -EINVAL;
}
+ if (host->cfg->can_calibrate)
+ return sunxi_mmc_calibrate(host, SDXC_REG_SAMP_DL_REG,
+ host->cfg->clk_delays[index].sample);
+ /* TODO: calibrate data strobe delay once HS-400 is supported. */
+
clk_set_phase(host->clk_sample, host->cfg->clk_delays[index].sample);
clk_set_phase(host->clk_output, host->cfg->clk_delays[index].output);
@@ -802,12 +806,6 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,
if (ret)
return ret;
- ret = sunxi_mmc_calibrate(host, SDXC_REG_SAMP_DL_REG);
- if (ret)
- return ret;
-
- /* TODO: enable calibrate on sdc2 SDXC_REG_DS_DL_REG of A64 */
-
return sunxi_mmc_oclk_onoff(host, 1);
}
@@ -1061,6 +1059,14 @@ static const struct sunxi_mmc_clk_delay sun9i_mmc_clk_delays[] = {
[SDXC_CLK_50M_DDR_8BIT] = { .output = 72, .sample = 72 },
};
+static const struct sunxi_mmc_clk_delay sun50i_mmc_clk_delays[] = {
+ [SDXC_CLK_400K] = { .output = 90, .sample = 0 },
+ [SDXC_CLK_25M] = { .output = 90, .sample = 0 },
+ [SDXC_CLK_50M] = { .output = 90, .sample = 0 },
+ [SDXC_CLK_50M_DDR] = { .output = 90, .sample = 0 },
+ [SDXC_CLK_50M_DDR_8BIT] = { .output = 90, .sample = 0 },
+};
+
static const struct sunxi_mmc_cfg sun4i_a10_cfg = {
.idma_des_size_bits = 13,
.clk_delays = NULL,
@@ -1087,7 +1093,7 @@ static const struct sunxi_mmc_cfg sun9i_a80_cfg = {
static const struct sunxi_mmc_cfg sun50i_a64_cfg = {
.idma_des_size_bits = 16,
- .clk_delays = NULL,
+ .clk_delays = sun50i_mmc_clk_delays,
.can_calibrate = true,
};
@@ -1134,7 +1140,7 @@ static int sunxi_mmc_resource_request(struct sunxi_mmc_host *host,
return PTR_ERR(host->clk_mmc);
}
- if (host->cfg->clk_delays) {
+ if (host->cfg->clk_delays && !host->cfg->can_calibrate) {
host->clk_output = devm_clk_get(&pdev->dev, "output");
if (IS_ERR(host->clk_output)) {
dev_err(&pdev->dev, "Could not get output clock\n");
--
2.8.2
^ permalink raw reply related
* [PATCH 2/5] drivers: mmc: sunxi: limit A64 MMC2 to 8K DMA buffer
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1483398226-29321-1-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
From: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Unlike the A64 user manual reports, the third MMC controller on the
A64 (and the only one capable of 8-bit HS400 eMMC transfers) has a
DMA buffer size limit of 8KB (much like the very old Allwinner SoCs).
This does not affect the other two controllers, so introduce a new
DT compatible string to let the driver use different settings for that
particular device. This will also help to enable the high-speed transfer
modes of that controller later.
Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
---
Documentation/devicetree/bindings/mmc/sunxi-mmc.txt | 1 +
drivers/mmc/host/sunxi-mmc.c | 7 +++++++
2 files changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
index 55cdd80..3d9170f 100644
--- a/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/sunxi-mmc.txt
@@ -14,6 +14,7 @@ Required properties:
* "allwinner,sun7i-a20-mmc"
* "allwinner,sun9i-a80-mmc"
* "allwinner,sun50i-a64-mmc"
+ * "allwinner,sun50i-a64-emmc"
- reg : mmc controller base registers
- clocks : a list with 4 phandle + clock specifier pairs
- clock-names : must contain "ahb", "mmc", "output" and "sample"
diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
index 1e156e8..165486bc 100644
--- a/drivers/mmc/host/sunxi-mmc.c
+++ b/drivers/mmc/host/sunxi-mmc.c
@@ -1097,12 +1097,19 @@ static const struct sunxi_mmc_cfg sun50i_a64_cfg = {
.can_calibrate = true,
};
+static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
+ .idma_des_size_bits = 13,
+ .clk_delays = sun50i_mmc_clk_delays,
+ .can_calibrate = true,
+};
+
static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
{ .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
{ .compatible = "allwinner,sun7i-a20-mmc", .data = &sun7i_a20_cfg },
{ .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
{ .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
+ { .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
--
2.8.2
^ permalink raw reply related
* [PATCH 3/5] arm64: dts: sun50i: add MMC nodes
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1483398226-29321-1-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 67 +++++++++++++++++++++++++++
1 file changed, 67 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index e0dcab8..c680566 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -150,6 +150,32 @@
pins = "PB8", "PB9";
function = "uart0";
};
+
+ mmc0_pins: mmc0@0 {
+ pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ };
+
+ mmc0_default_cd_pin: mmc0_cd_pin@0 {
+ pins = "PF6";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1@0 {
+ pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ };
+
+ mmc2_pins: mmc2@0 {
+ pins = "PC1", "PC5", "PC6", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ };
};
uart0: serial@1c28000 {
@@ -240,6 +266,47 @@
#size-cells = <0>;
};
+ mmc0: mmc@1c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu 31>, <&ccu 75>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu 8>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@1c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu 32>, <&ccu 76>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu 9>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@1c11000 {
+ compatible = "allwinner,sun50i-a64-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu 33>, <&ccu 77>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu 10>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
gic: interrupt-controller@1c81000 {
compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
--
2.8.2
^ permalink raw reply related
* [PATCH 4/5] arm64: dts: Pine64: add MMC support
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1483398226-29321-1-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
---
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index 4709590..c18ab03 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -55,6 +55,13 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
&uart0 {
@@ -72,3 +79,14 @@
&i2c1_pins {
bias-pull-up;
};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_default_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ cd-gpios = <&pio 5 6 0>;
+ cd-inverted;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
--
2.8.2
^ permalink raw reply related
* [PATCH 5/5] arm64: dts: add BananaPi-M64 support
From: Andre Przywara @ 2017-01-02 23:03 UTC (permalink / raw)
To: Maxime Ripard, Ulf Hansson
Cc: Chen-Yu Tsai, Hans De Goede, Icenowy Zheng, Mark Rutland,
Rob Herring, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-mmc-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <1483398226-29321-1-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.
Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 125 +++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 10 ++
3 files changed, 136 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 1e29a5a..51ecb04 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,4 +1,5 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-bananapi-m64.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
new file mode 100644
index 0000000..941ea07
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -0,0 +1,125 @@
+/*
+ * Copyright (c) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun50i-a64.dtsi"
+
+/ {
+ model = "BananaPi-M64";
+ compatible = "sinovoip,bananapi-m64", "allwinner,sun50i-a64";
+
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_4>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "okay";
+};
+
+&i2c1_pins {
+ bias-pull-up;
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_default_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ cd-gpios = <&pio 5 6 0>;
+ cd-inverted;
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_pins {
+ /* Increase drive strength for DDR modes */
+ drive-strength = <40>;
+ /* eMMC is missing pull-ups */
+ bias-pull-up;
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index c680566..9de96ba 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -151,6 +151,16 @@
function = "uart0";
};
+ uart1_pins: uart1@0 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_pins_4: uart1_4@0 {
+ pins = "PG6", "PG7", "PG8", "PG9";
+ function = "uart1";
+ };
+
mmc0_pins: mmc0@0 {
pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
function = "mmc0";
--
2.8.2
^ permalink raw reply related
* [PATCH v2 1/2] Doc: devicetree: bindings: Add vendor prefix entry - lwn
From: Lukasz Majewski @ 2017-01-02 23:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Russell King, Shawn Guo, Fabio Estevam,
linux-kernel, devicetree, linux-arm-kernel, Vladimir Zapolskiy
Cc: Sascha Hauer, Zerlauth Karl (LWN), Lukasz Majewski,
Lukasz Majewski
In-Reply-To: <1482794396-16153-1-git-send-email-l.majewski@majess.pl>
This patch adds entry for LWN - the Liebherr-Werk Nenzing GmbH company to
vendor-prefixes.txt file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
Changes for v2:
- New patch
---
Documentation/devicetree/bindings/vendor-prefixes.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index f0a48ea..dd8b2eb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -158,6 +158,7 @@ lg LG Corporation
linux Linux-specific binding
lltc Linear Technology Corporation
lsi LSI Corp. (LSI Logic)
+lwn Liebherr-Werk Nenzing GmbH
marvell Marvell Technology Group Ltd.
maxim Maxim Integrated Products
meas Measurement Specialties
--
2.1.4
^ permalink raw reply related
* [PATCH v2 2/2] ARM: dts: imx6q: Add mccmon6 board support
From: Lukasz Majewski @ 2017-01-02 23:43 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Russell King, Shawn Guo, Fabio Estevam,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Vladimir Zapolskiy
Cc: Sascha Hauer, Zerlauth Karl (LWN), Lukasz Majewski,
Lukasz Majewski
In-Reply-To: <1483400618-16845-1-git-send-email-lukma-ynQEQJNshbs@public.gmane.org>
From: Lukasz Majewski <l.majewski-AM3owJQeAb5mR6Xm/wNWPw@public.gmane.org>
This patch provides support for Liebherr's Monitor 6 board (abverrated as
mccmon6) to Linux kernel.
Signed-off-by: Lukasz Majewski <lukma-ynQEQJNshbs@public.gmane.org>
---
Changes for v2:
- Reorganize the dts file according to Valdimir Zapolskiy's comments
---
MCCMON6 board support depends on following patches:
1. "video: backlight: pwm_bl: Initialize fb_bl_on[x] and use_count during pwm_backlight_probe()"
http://patchwork.ozlabs.org/patch/708844/
2. "pwm: imx: Provide atomic operation for IMX PWM driver"
http://patchwork.ozlabs.org/patch/708847/ - http://patchwork.ozlabs.org/patch/708843/
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-mccmon6.dts | 477 ++++++++++++++++++++++++++++++++++++
2 files changed, 478 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-mccmon6.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index c558ba7..0aa8e89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -383,6 +383,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-hummingboard.dtb \
imx6q-icore-rqs.dtb \
imx6q-marsboard.dtb \
+ imx6q-mccmon6.dtb \
imx6q-nitrogen6x.dtb \
imx6q-nitrogen6_max.dtb \
imx6q-novena.dtb \
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
new file mode 100644
index 0000000..7128dc2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
@@ -0,0 +1,477 @@
+/*
+ * Copyright 2016-2017
+ * Lukasz Majewski, DENX Software Engineering, lukma-ynQEQJNshbs@public.gmane.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
+ compatible = "lwn,mccmon6", "fsl,imx6q";
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ backlight_lvds: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
+ brightness-levels = < 0 1 2 3 4 5 6 7 8 9
+ 10 11 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27 28 29
+ 30 31 32 33 34 35 36 37 38 39
+ 40 41 42 43 44 45 46 47 48 49
+ 50 51 52 53 54 55 56 57 58 59
+ 60 61 62 63 64 65 66 67 68 69
+ 70 71 72 73 74 75 76 77 78 79
+ 80 81 82 83 84 85 86 87 88 89
+ 90 91 92 93 94 95 96 97 98 99
+ 100 101 102 103 104 105 106 107 108 109
+ 110 111 112 113 114 115 116 117 118 119
+ 120 121 122 123 124 125 126 127 128 129
+ 130 131 132 133 134 135 136 137 138 139
+ 140 141 142 143 144 145 146 147 148 149
+ 150 151 152 153 154 155 156 157 158 159
+ 160 161 162 163 164 165 166 167 168 169
+ 170 171 172 173 174 175 176 177 178 179
+ 180 181 182 183 184 185 186 187 188 189
+ 190 191 192 193 194 195 196 197 198 199
+ 200 201 202 203 204 205 206 207 208 209
+ 210 211 212 213 214 215 216 217 218 219
+ 220 221 222 223 224 225 226 227 228 229
+ 230 231 232 233 234 235 236 237 238 239
+ 240 241 242 243 244 245 246 247 248 249
+ 250 251 252 253 254 255>;
+ default-brightness-level = <50>;
+ enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ };
+
+ reg_lvds: regulator-lvds {
+ compatible = "regulator-fixed";
+ regulator-name = "lvds_ppen";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_lvds>;
+ gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ panel-lvds0 {
+ compatible = "innolux,g121x1-l03";
+ backlight = <&backlight_lvds>;
+ power-supply = <®_lvds>;
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ imx6q-mccmon6 {
+ pinctrl_backlight: dispgrp {
+ fsl,pins = <
+ /* BLEN_OUT */
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ >;
+ };
+
+ pinctrl_ecspi3_cs: ecspi3cs {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000
+ >;
+ };
+
+ pinctrl_ecspi3_flwp: ecspi3flwp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x80000000
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+ MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_reg_lvds: req_lvds_grp {
+ fsl,pins = <
+ /* LVDS_PPEN_OUT */
+ MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
+ >;
+ };
+
+ pinctrl_weim_cs0: weimcs0grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
+ >;
+ };
+
+ pinctrl_weim_nor: weimnorgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
+ MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
+ MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+ MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+ MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+ MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+ MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+ MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+ MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+ MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+ MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+ MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+ MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+ MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+ MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+ MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+ MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+ MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+ MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+ MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+ MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+ MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+ MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+ MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+ MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+ MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+ MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+ MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
+ MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
+ MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
+ MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
+ MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
+ MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
+ MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
+ MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
+ MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
+ MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
+ MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
+ MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
+ MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
+ MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
+ MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
+ MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
+ >;
+ };
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+ status = "okay";
+
+ flash: s25sl032p@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spansion,s25sl032p", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio1 27 0>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+ <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ pmic: pfuze100@08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm2 {
+ #pwm-cells = <3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&weim {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0 0 0x08000000 0x08000000>;
+ status = "okay";
+
+ nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0 0 0x02000000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bank-width = <2>;
+ use-advanced-sector-protection;
+ fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+ 0x0000c000 0x1404a38e 0x00000000>;
+ };
+};
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* RE: [PATCH v2 06/12] driver: pinctrl: imx: Add pinctrl driver support for imx6sll
From: Jacky Bai @ 2017-01-03 1:00 UTC (permalink / raw)
To: Linus Walleij
Cc: Shawn Guo, Michael Turquette, Stephen Boyd, Rob Herring,
Mark Rutland, Sascha Hauer, Fabio Estevam, Daniel Lezcano,
Thomas Gleixner, Philipp Zabel, linux-clk,
devicetree@vger.kernel.org, linux-gpio@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, jacky.baip@gmail.com
In-Reply-To: <CACRpkdZYH-X=SG7AfCOgKA9U0WL9941e-zo_tgUF74mdns2_7Q@mail.gmail.com>
> Subject: Re: [PATCH v2 06/12] driver: pinctrl: imx: Add pinctrl driver support for
> imx6sll
>
> On Tue, Dec 27, 2016 at 10:47 AM, Bai Ping <ping.bai@nxp.com> wrote:
>
> > Add pinctrl driver support for imx6sll.
> >
> > Signed-off-by: Bai Ping <ping.bai@nxp.com>
> (...)
> > +++ b/arch/arm/mach-imx/Kconfig
> > @@ -514,6 +514,7 @@ config SOC_IMX6SL
> >
> > config SOC_IMX6SLL
> > bool "i.MX6 SoloLiteLite support"
> > + select PINCTRL_IMX6SLL
>
> This needs to be separate so I can merge the pure pin control patch to my tree.
>
> Apart from that, look into using generic pinconf.
>
Thanks for review, I will try to use generic pinconf
> Yours,
> Linus Walleij
^ permalink raw reply
* RE: [PATCH 2/2] ARM: imx: Add speed grading check for imx6ul
From: Jacky Bai @ 2017-01-03 1:01 UTC (permalink / raw)
To: Shawn Guo
Cc: kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org, Fabio Estevam,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
In-Reply-To: <20161230115717.GR6177@dragon>
> On Wed, Nov 30, 2016 at 11:04:58AM +0800, Bai Ping wrote:
> > On i.MX6UL, it has two type of part, the difference is the max ARM
> > frequency that can run at(528MHz/700MHz).
> > The part can be identified by part marking for speed grading fuse.
> > This patch add speed grading check to disable the unsupported OPP
> > dynamically.
> >
> > Signed-off-by: Bai Ping <ping.bai-3arQi8VN3Tc@public.gmane.org>
>
> We chose to handle such speed grading thing in IMX platform code with the
> assumption that this is a special case for i.MX6Q only. No, I'm not going to take
> such code for any other i.MX6 SoCs. Please patch cpufreq driver to handle the
> speed grading check.
>
Thanks, I will try to add in cpufreq.
> Shawn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH] ARM: dts: imx: remove obsoleted property fsl,spi-num-chipselects
From: Shawn Guo @ 2017-01-03 1:23 UTC (permalink / raw)
To: Vladimir Zapolskiy
Cc: Fabio Estevam, Sascha Hauer, Alexander Shiyan, Rob Herring,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <20161224054354.28289-1-vz-ChpfBGZJDbMAvxtiuMwx3w@public.gmane.org>
On Sat, Dec 24, 2016 at 07:43:54AM +0200, Vladimir Zapolskiy wrote:
> Since commit b36581df7e78 ("spi: imx: Using existing properties for
> chipselects") the device tree property 'fsl,spi-num-chipselects' is
> unused and it is already marked as obsolete in device tree binding
> documentation. Remove the property from the existing DTS files to
> avoid its reoccurence on copying.
>
> Signed-off-by: Vladimir Zapolskiy <vz-ChpfBGZJDbMAvxtiuMwx3w@public.gmane.org>
Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v2 2/2] ARM: dts: imx6q: Add mccmon6 board support
From: Shawn Guo @ 2017-01-03 2:06 UTC (permalink / raw)
To: Lukasz Majewski
Cc: Rob Herring, Mark Rutland, Russell King, Fabio Estevam,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
Vladimir Zapolskiy, Sascha Hauer, Zerlauth Karl (LWN),
Lukasz Majewski
In-Reply-To: <1483400618-16845-2-git-send-email-lukma-ynQEQJNshbs@public.gmane.org>
On Tue, Jan 03, 2017 at 12:43:38AM +0100, Lukasz Majewski wrote:
> From: Lukasz Majewski <l.majewski-AM3owJQeAb5mR6Xm/wNWPw@public.gmane.org>
>
> This patch provides support for Liebherr's Monitor 6 board (abverrated as
> mccmon6) to Linux kernel.
>
> Signed-off-by: Lukasz Majewski <lukma-ynQEQJNshbs@public.gmane.org>
> ---
> Changes for v2:
> - Reorganize the dts file according to Valdimir Zapolskiy's comments
>
> ---
> MCCMON6 board support depends on following patches:
>
> 1. "video: backlight: pwm_bl: Initialize fb_bl_on[x] and use_count during pwm_backlight_probe()"
> http://patchwork.ozlabs.org/patch/708844/
>
> 2. "pwm: imx: Provide atomic operation for IMX PWM driver"
> http://patchwork.ozlabs.org/patch/708847/ - http://patchwork.ozlabs.org/patch/708843/
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-mccmon6.dts | 477 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 478 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-mccmon6.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index c558ba7..0aa8e89 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -383,6 +383,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-hummingboard.dtb \
> imx6q-icore-rqs.dtb \
> imx6q-marsboard.dtb \
> + imx6q-mccmon6.dtb \
> imx6q-nitrogen6x.dtb \
> imx6q-nitrogen6_max.dtb \
> imx6q-novena.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
> new file mode 100644
> index 0000000..7128dc2
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
> @@ -0,0 +1,477 @@
> +/*
> + * Copyright 2016-2017
> + * Lukasz Majewski, DENX Software Engineering, lukma-ynQEQJNshbs@public.gmane.org
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + */
You might want to GPL/X11 dual licence for non-Linux device tree users.
There are a plenty of examples in arch/arm/boot/dts. But note the
following correction.
https://patchwork.kernel.org/patch/9475057/
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Liebherr (LWN) monitor6 i.MX6 Quad Board";
> + compatible = "lwn,mccmon6", "fsl,imx6q";
> +
> + memory {
> + reg = <0x10000000 0x80000000>;
> + };
> +
> + backlight_lvds: backlight {
> + compatible = "pwm-backlight";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_backlight>;
> + pwms = <&pwm2 0 5000000 PWM_POLARITY_INVERTED>;
> + brightness-levels = < 0 1 2 3 4 5 6 7 8 9
> + 10 11 12 13 14 15 16 17 18 19
> + 20 21 22 23 24 25 26 27 28 29
> + 30 31 32 33 34 35 36 37 38 39
> + 40 41 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57 58 59
> + 60 61 62 63 64 65 66 67 68 69
> + 70 71 72 73 74 75 76 77 78 79
> + 80 81 82 83 84 85 86 87 88 89
> + 90 91 92 93 94 95 96 97 98 99
> + 100 101 102 103 104 105 106 107 108 109
> + 110 111 112 113 114 115 116 117 118 119
> + 120 121 122 123 124 125 126 127 128 129
> + 130 131 132 133 134 135 136 137 138 139
> + 140 141 142 143 144 145 146 147 148 149
> + 150 151 152 153 154 155 156 157 158 159
> + 160 161 162 163 164 165 166 167 168 169
> + 170 171 172 173 174 175 176 177 178 179
> + 180 181 182 183 184 185 186 187 188 189
> + 190 191 192 193 194 195 196 197 198 199
> + 200 201 202 203 204 205 206 207 208 209
> + 210 211 212 213 214 215 216 217 218 219
> + 220 221 222 223 224 225 226 227 228 229
> + 230 231 232 233 234 235 236 237 238 239
> + 240 241 242 243 244 245 246 247 248 249
> + 250 251 252 253 254 255>;
> + default-brightness-level = <50>;
> + enable-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + reg_lvds: regulator-lvds {
> + compatible = "regulator-fixed";
> + regulator-name = "lvds_ppen";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_lvds>;
> + gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + panel-lvds0 {
> + compatible = "innolux,g121x1-l03";
> + backlight = <&backlight_lvds>;
> + power-supply = <®_lvds>;
> +
> + port {
> + panel_in_lvds0: endpoint {
> + remote-endpoint = <&lvds0_out>;
> + };
> + };
> + };
> +};
> +
> +&iomuxc {
Considering the data amount of this node, we generally put it at the
bottom of the file to improve the readability of the rest.
> + pinctrl-names = "default";
> +
> + imx6q-mccmon6 {
This container node can now be dropped completely to save one level of
indentation.
> + pinctrl_backlight: dispgrp {
> + fsl,pins = <
> + /* BLEN_OUT */
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> + >;
> + };
> +
> + pinctrl_ecspi3: ecspi3grp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> + >;
> + };
> +
> + pinctrl_ecspi3_cs: ecspi3cs {
ecspi3csgrp, if we follow the naming scheme used in other nodes.
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000
> + >;
> + };
> +
> + pinctrl_ecspi3_flwp: ecspi3flwp {
Ditto
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x80000000
> + >;
> + };
> +
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
> + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_pwm2: pwm2grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_reg_lvds: req_lvds_grp {
reglvdsgrp
> + fsl,pins = <
> + /* LVDS_PPEN_OUT */
> + MX6QDL_PAD_SD1_DAT2__GPIO1_IO19 0x1b0b0
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> + MX6QDL_PAD_SD3_RST__SD3_RESET 0x17059
> + >;
> + };
> +
> + pinctrl_weim_cs0: weimcs0grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1
> + >;
> + };
> +
> + pinctrl_weim_nor: weimnorgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1
> + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1
> + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
> + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
> + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
> + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
> + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
> + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
> + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
> + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
> + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
> + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
> + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
> + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
> + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
> + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
> + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
> + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
> + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
> + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
> + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
> + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
> + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
> + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
> + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
> + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
> + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
> + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1
> + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1
> + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1
> + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1
> + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1
> + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1
> + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1
> + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1
> + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1
> + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1
> + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1
> + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1
> + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1
> + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1
> + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1
> + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1
> + >;
> + };
> + };
> +};
> +
> +&ecspi3 {
> + cs-gpios = <&gpio4 24 0>;
GPIO_ACTIVE_HIGH?
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
> + status = "okay";
> +
> + flash: s25sl032p@0 {
Node name should be as generic as possible, while label name can be
specific. That said, 's25sl032p: flash@0' should be better.
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "spansion,s25sl032p", "jedec,spi-nor";
"spansion,s25sl032p" doesn't seem to be documented. Can it be dropped?
> + spi-max-frequency = <40000000>;
> + reg = <0>;
> + };
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet>;
> + phy-mode = "rgmii";
> + phy-reset-gpios = <&gpio1 27 0>;
GPIO_ACTIVE_xxx? But you probably need GPIO_ACTIVE_LOW.
> + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + pmic: pfuze100@08 {
pfuze100: pmic@08
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw2_reg: sw2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw3b_reg: sw3b {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + sw4_reg: sw4 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&ldb {
> + status = "okay";
> +
> + lvds0: lvds-channel@0 {
> + fsl,data-mapping = "spwg";
> + fsl,data-width = <24>;
> + status = "okay";
> +
> + port@4 {
> + reg = <4>;
> +
> + lvds0_out: endpoint {
> + remote-endpoint = <&panel_in_lvds0>;
> + };
> + };
> + };
> +};
> +
> +&pwm2 {
> + #pwm-cells = <3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + status = "okay";
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&weim {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>;
> + #address-cells = <2>;
> + #size-cells = <1>;
These two properties can be saved from board dts since commit
1be81ea58607 ("ARM: dts: imx6: Add imx-weim parameters to dtsi's").
Shawn
> + ranges = <0 0 0x08000000 0x08000000>;
> + status = "okay";
> +
> + nor@0,0 {
> + compatible = "cfi-flash";
> + reg = <0 0 0x02000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + bank-width = <2>;
> + use-advanced-sector-protection;
> + fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
> + 0x0000c000 0x1404a38e 0x00000000>;
> + };
> +};
> --
> 2.1.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH 3/5] arm64: dts: sun50i: add MMC nodes
From: Chen-Yu Tsai @ 2017-01-03 2:52 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Ulf Hansson, Chen-Yu Tsai, Hans De Goede,
Icenowy Zheng, Mark Rutland, Rob Herring, devicetree,
linux-mmc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel, linux-sunxi, linux-kernel
In-Reply-To: <1483398226-29321-4-git-send-email-andre.przywara-5wv7dgnIgG8@public.gmane.org>
Hi,
On Tue, Jan 3, 2017 at 7:03 AM, Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org> wrote:
A commit message explaining the mmc controllers would be nice.
> Signed-off-by: Andre Przywara <andre.przywara-5wv7dgnIgG8@public.gmane.org>
> ---
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 67 +++++++++++++++++++++++++++
> 1 file changed, 67 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index e0dcab8..c680566 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -150,6 +150,32 @@
> pins = "PB8", "PB9";
> function = "uart0";
> };
> +
> + mmc0_pins: mmc0@0 {
> + pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
> + function = "mmc0";
> + drive-strength = <30>;
> + };
> +
> + mmc0_default_cd_pin: mmc0_cd_pin@0 {
> + pins = "PF6";
> + function = "gpio_in";
> + bias-pull-up;
> + };
We are starting to drop pinmux nodes for gpio usage.
> +
> + mmc1_pins: mmc1@0 {
> + pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5";
> + function = "mmc1";
> + drive-strength = <30>;
> + };
> +
> + mmc2_pins: mmc2@0 {
> + pins = "PC1", "PC5", "PC6", "PC8", "PC9",
> + "PC10", "PC11", "PC12", "PC13", "PC14",
> + "PC15", "PC16";
> + function = "mmc2";
> + drive-strength = <30>;
> + };
Moreover I think you should split out the pinmux nodes to a separate patch.
> };
>
> uart0: serial@1c28000 {
> @@ -240,6 +266,47 @@
> #size-cells = <0>;
> };
>
> + mmc0: mmc@1c0f000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
Given that sun5i doesn't support mmc delay timings, and the A64 has
calibration and delay timings, I wouldn't call them compatible.
Or are you claiming that for the A64 has a delay of 0 for the
currently supported speeds, so the calibration doesn't really
matter? If so this should be mentioned in the commit message.
> + reg = <0x01c0f000 0x1000>;
> + clocks = <&ccu 31>, <&ccu 75>;
The clock / reset index macros are in the tree now.
Please switch to them.
ChenYu
> + clock-names = "ahb", "mmc";
> + resets = <&ccu 8>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc1: mmc@1c10000 {
> + compatible = "allwinner,sun50i-a64-mmc",
> + "allwinner,sun5i-a13-mmc";
> + reg = <0x01c10000 0x1000>;
> + clocks = <&ccu 32>, <&ccu 76>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu 9>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc2: mmc@1c11000 {
> + compatible = "allwinner,sun50i-a64-emmc";
> + reg = <0x01c11000 0x1000>;
> + clocks = <&ccu 33>, <&ccu 77>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu 10>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> gic: interrupt-controller@1c81000 {
> compatible = "arm,gic-400";
> reg = <0x01c81000 0x1000>,
> --
> 2.8.2
>
^ permalink raw reply
* [PATCH v19 0/4] Mediatek MT8173 CMDQ support
From: HS Liao @ 2017-01-03 3:05 UTC (permalink / raw)
To: Rob Herring, Matthias Brugger, Jassi Brar
Cc: Monica Wang, Jiaguang Zhang, Nicolas Boichat, cawa cheng, HS Liao,
Bibby Hsieh, YT Shen, Damon Chu,
devicetree-u79uwXL29TY76Z2rM5mHXA, Sascha Hauer, Daoyuan Huang,
Sascha Hauer, Houlong Wei, Glory Hung, CK HU,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
srv_heupstream-NuS5LvNUpcJWk0Htik3J/w, Josh-YC Liu,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Dennis-YC Hsieh,
Philipp Zabel
Hi,
This is Mediatek MT8173 Command Queue(CMDQ) driver. The CMDQ is used
to help write registers with critical time limitation, such as
updating display configuration during the vblank. It controls Global
Command Engine (GCE) hardware to achieve this requirement.
These patches have a build dependency on top of v4.10-rc1.
Changes since v18:
- add "select MAILBOX" into CMDQ helper
- remove power saving part to prevent a potential bug
Best regards,
HS Liao
HS Liao (4):
dt-bindings: soc: Add documentation for the MediaTek GCE unit
mailbox: mediatek: Add Mediatek CMDQ driver
arm64: dts: mt8173: Add GCE node
soc: mediatek: Add Mediatek CMDQ helper
.../devicetree/bindings/mailbox/mtk-gce.txt | 43 ++
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 10 +
drivers/mailbox/Kconfig | 10 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mtk-cmdq-mailbox.c | 596 +++++++++++++++++++++
drivers/soc/mediatek/Kconfig | 12 +
drivers/soc/mediatek/Makefile | 1 +
drivers/soc/mediatek/mtk-cmdq-helper.c | 310 +++++++++++
include/linux/mailbox/mtk-cmdq-mailbox.h | 75 +++
include/linux/soc/mediatek/mtk-cmdq.h | 174 ++++++
10 files changed, 1233 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/mtk-gce.txt
create mode 100644 drivers/mailbox/mtk-cmdq-mailbox.c
create mode 100644 drivers/soc/mediatek/mtk-cmdq-helper.c
create mode 100644 include/linux/mailbox/mtk-cmdq-mailbox.h
create mode 100644 include/linux/soc/mediatek/mtk-cmdq.h
--
1.9.1
^ permalink raw reply
* [PATCH v19 1/4] dt-bindings: soc: Add documentation for the MediaTek GCE unit
From: HS Liao @ 2017-01-03 3:05 UTC (permalink / raw)
To: Rob Herring, Matthias Brugger, Jassi Brar
Cc: Monica Wang, Jiaguang Zhang, Nicolas Boichat, cawa cheng, HS Liao,
Bibby Hsieh, YT Shen, Damon Chu,
devicetree-u79uwXL29TY76Z2rM5mHXA, Sascha Hauer, Daoyuan Huang,
Sascha Hauer, Houlong Wei, Glory Hung, CK HU,
linux-mediatek-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
srv_heupstream-NuS5LvNUpcJWk0Htik3J/w, Josh-YC Liu,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Dennis-YC Hsieh,
Philipp Zabel
In-Reply-To: <1483412751-28690-1-git-send-email-hs.liao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
This adds documentation for the MediaTek Global Command Engine (GCE) unit
found in MT8173 SoCs.
Signed-off-by: HS Liao <hs.liao-NuS5LvNUpcJWk0Htik3J/w@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
.../devicetree/bindings/mailbox/mtk-gce.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/mtk-gce.txt
diff --git a/Documentation/devicetree/bindings/mailbox/mtk-gce.txt b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt
new file mode 100644
index 0000000..d2d3ccb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt
@@ -0,0 +1,43 @@
+MediaTek GCE
+===============
+
+The Global Command Engine (GCE) is used to help read/write registers with
+critical time limitation, such as updating display configuration during the
+vblank. The GCE can be used to implement the Command Queue (CMDQ) driver.
+
+CMDQ driver uses mailbox framework for communication. Please refer to
+mailbox.txt for generic information about mailbox device-tree bindings.
+
+Required properties:
+- compatible: Must be "mediatek,mt8173-gce"
+- reg: Address range of the GCE unit
+- interrupts: The interrupt signal from the GCE block
+- clock: Clocks according to the common clock binding
+- clock-names: Must be "gce" to stand for GCE clock
+- #mbox-cells: Should be 2
+
+Required properties for a client device:
+- mboxes: client use mailbox to communicate with GCE, it should have this
+ property and list of phandle, mailbox channel specifiers, and atomic
+ execution flag.
+
+Example:
+
+ gce: gce@10212000 {
+ compatible = "mediatek,mt8173-gce";
+ reg = <0 0x10212000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_GCE>;
+ clock-names = "gce";
+
+ #mbox-cells = <2>;
+ };
+
+Example for a client device:
+
+ mmsys: clock-controller@14000000 {
+ compatible = "mediatek,mt8173-mmsys";
+ mboxes = <&gce 0 1 /* main display with atomic execution */
+ &gce 1 1>; /* sub display with atomic execution */
+ ...
+ };
--
1.9.1
^ permalink raw reply related
* [PATCH v19 2/4] mailbox: mediatek: Add Mediatek CMDQ driver
From: HS Liao @ 2017-01-03 3:05 UTC (permalink / raw)
To: Rob Herring, Matthias Brugger, Jassi Brar
Cc: Daniel Kurtz, Sascha Hauer, devicetree, linux-kernel,
linux-arm-kernel, linux-mediatek, srv_heupstream, Sascha Hauer,
Philipp Zabel, Nicolas Boichat, CK HU, cawa cheng, Bibby Hsieh,
YT Shen, Daoyuan Huang, Damon Chu, Josh-YC Liu, Glory Hung,
Jiaguang Zhang, Dennis-YC Hsieh
In-Reply-To: <1483412751-28690-1-git-send-email-hs.liao@mediatek.com>
This patch is first version of Mediatek Command Queue(CMDQ) driver. The
CMDQ is used to help write registers with critical time limitation,
such as updating display configuration during the vblank. It controls
Global Command Engine (GCE) hardware to achieve this requirement.
Currently, CMDQ only supports display related hardwares, but we expect
it can be extended to other hardwares for future requirements.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
---
drivers/mailbox/Kconfig | 10 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mtk-cmdq-mailbox.c | 596 +++++++++++++++++++++++++++++++
include/linux/mailbox/mtk-cmdq-mailbox.h | 75 ++++
4 files changed, 683 insertions(+)
create mode 100644 drivers/mailbox/mtk-cmdq-mailbox.c
create mode 100644 include/linux/mailbox/mtk-cmdq-mailbox.h
diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index ceff415..9108dd4 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -152,4 +152,14 @@ config BCM_PDC_MBOX
Mailbox implementation for the Broadcom PDC ring manager,
which provides access to various offload engines on Broadcom
SoCs. Say Y here if you want to use the Broadcom PDC.
+
+config MTK_CMDQ_MBOX
+ bool "MediaTek CMDQ Mailbox Support"
+ depends on ARM64 && ( ARCH_MEDIATEK || COMPILE_TEST )
+ select MTK_INFRACFG
+ help
+ Say yes here to add support for the MediaTek Command Queue (CMDQ)
+ mailbox driver. The CMDQ is used to help read/write registers with
+ critical time limitation, such as updating display configuration
+ during the vblank.
endif
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index 7dde4f6..fad8965 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -31,3 +31,5 @@ obj-$(CONFIG_HI6220_MBOX) += hi6220-mailbox.o
obj-$(CONFIG_BCM_PDC_MBOX) += bcm-pdc-mailbox.o
obj-$(CONFIG_TEGRA_HSP_MBOX) += tegra-hsp.o
+
+obj-$(CONFIG_MTK_CMDQ_MBOX) += mtk-cmdq-mailbox.o
diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c b/drivers/mailbox/mtk-cmdq-mailbox.c
new file mode 100644
index 0000000..747bcd3
--- /dev/null
+++ b/drivers/mailbox/mtk-cmdq-mailbox.c
@@ -0,0 +1,596 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/mailbox/mtk-cmdq-mailbox.h>
+#include <linux/timer.h>
+
+#define CMDQ_THR_MAX_COUNT 3 /* main, sub, general(misc) */
+#define CMDQ_OP_CODE_MASK (0xff << CMDQ_OP_CODE_SHIFT)
+#define CMDQ_TIMEOUT_MS 1000
+#define CMDQ_IRQ_MASK 0xffff
+#define CMDQ_NUM_CMD(t) (t->cmd_buf_size / CMDQ_INST_SIZE)
+
+#define CMDQ_CURR_IRQ_STATUS 0x10
+#define CMDQ_THR_SLOT_CYCLES 0x30
+
+#define CMDQ_THR_BASE 0x100
+#define CMDQ_THR_SIZE 0x80
+#define CMDQ_THR_WARM_RESET 0x00
+#define CMDQ_THR_ENABLE_TASK 0x04
+#define CMDQ_THR_SUSPEND_TASK 0x08
+#define CMDQ_THR_CURR_STATUS 0x0c
+#define CMDQ_THR_IRQ_STATUS 0x10
+#define CMDQ_THR_IRQ_ENABLE 0x14
+#define CMDQ_THR_CURR_ADDR 0x20
+#define CMDQ_THR_END_ADDR 0x24
+#define CMDQ_THR_WAIT_TOKEN 0x30
+
+#define CMDQ_THR_ENABLED 0x1
+#define CMDQ_THR_DISABLED 0x0
+#define CMDQ_THR_SUSPEND 0x1
+#define CMDQ_THR_RESUME 0x0
+#define CMDQ_THR_STATUS_SUSPENDED BIT(1)
+#define CMDQ_THR_DO_WARM_RESET BIT(0)
+#define CMDQ_THR_ACTIVE_SLOT_CYCLES 0x3200
+#define CMDQ_THR_IRQ_DONE 0x1
+#define CMDQ_THR_IRQ_ERROR 0x12
+#define CMDQ_THR_IRQ_EN (CMDQ_THR_IRQ_ERROR | CMDQ_THR_IRQ_DONE)
+#define CMDQ_THR_IS_WAITING BIT(31)
+
+#define CMDQ_JUMP_BY_OFFSET 0x10000000
+#define CMDQ_JUMP_BY_PA 0x10000001
+
+struct cmdq_thread {
+ struct mbox_chan *chan;
+ void __iomem *base;
+ struct list_head task_busy_list;
+ struct timer_list timeout;
+ bool atomic_exec;
+};
+
+struct cmdq_task {
+ struct cmdq *cmdq;
+ struct list_head list_entry;
+ dma_addr_t pa_base;
+ struct cmdq_thread *thread;
+ struct cmdq_pkt *pkt; /* the packet sent from mailbox client */
+};
+
+struct cmdq {
+ struct mbox_controller mbox;
+ void __iomem *base;
+ u32 irq;
+ struct cmdq_thread thread[CMDQ_THR_MAX_COUNT];
+ struct clk *clock;
+ bool suspended;
+};
+
+static int cmdq_thread_suspend(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ u32 status;
+
+ writel(CMDQ_THR_SUSPEND, thread->base + CMDQ_THR_SUSPEND_TASK);
+
+ /* If already disabled, treat as suspended successful. */
+ if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+ return 0;
+
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_STATUS,
+ status, status & CMDQ_THR_STATUS_SUSPENDED, 0, 10)) {
+ dev_err(cmdq->mbox.dev, "suspend GCE thread 0x%x failed\n",
+ (u32)(thread->base - cmdq->base));
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+static void cmdq_thread_resume(struct cmdq_thread *thread)
+{
+ writel(CMDQ_THR_RESUME, thread->base + CMDQ_THR_SUSPEND_TASK);
+}
+
+static int cmdq_thread_reset(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ u32 warm_reset;
+
+ writel(CMDQ_THR_DO_WARM_RESET, thread->base + CMDQ_THR_WARM_RESET);
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_WARM_RESET,
+ warm_reset, !(warm_reset & CMDQ_THR_DO_WARM_RESET),
+ 0, 10)) {
+ dev_err(cmdq->mbox.dev, "reset GCE thread 0x%x failed\n",
+ (u32)(thread->base - cmdq->base));
+ return -EFAULT;
+ }
+ writel(CMDQ_THR_ACTIVE_SLOT_CYCLES, cmdq->base + CMDQ_THR_SLOT_CYCLES);
+ return 0;
+}
+
+static void cmdq_thread_disable(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ cmdq_thread_reset(cmdq, thread);
+ writel(CMDQ_THR_DISABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+}
+
+/* notify GCE to re-fetch commands by setting GCE thread PC */
+static void cmdq_thread_invalidate_fetched_data(struct cmdq_thread *thread)
+{
+ writel(readl(thread->base + CMDQ_THR_CURR_ADDR),
+ thread->base + CMDQ_THR_CURR_ADDR);
+}
+
+static void cmdq_task_insert_into_thread(struct cmdq_task *task)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ struct cmdq_thread *thread = task->thread;
+ struct cmdq_task *prev_task = list_last_entry(
+ &thread->task_busy_list, typeof(*task), list_entry);
+ u64 *prev_task_base = prev_task->pkt->va_base;
+
+ /* let previous task jump to this task */
+ dma_sync_single_for_cpu(dev, prev_task->pa_base,
+ prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+ prev_task_base[CMDQ_NUM_CMD(prev_task->pkt) - 1] =
+ (u64)CMDQ_JUMP_BY_PA << 32 | task->pa_base;
+ dma_sync_single_for_device(dev, prev_task->pa_base,
+ prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+
+ cmdq_thread_invalidate_fetched_data(thread);
+}
+
+static bool cmdq_command_is_wfe(u64 cmd)
+{
+ u64 wfe_option = CMDQ_WFE_UPDATE | CMDQ_WFE_WAIT | CMDQ_WFE_WAIT_VALUE;
+ u64 wfe_op = (u64)(CMDQ_CODE_WFE << CMDQ_OP_CODE_SHIFT) << 32;
+ u64 wfe_mask = (u64)CMDQ_OP_CODE_MASK << 32 | 0xffffffff;
+
+ return ((cmd & wfe_mask) == (wfe_op | wfe_option));
+}
+
+/* we assume tasks in the same display GCE thread are waiting the same event. */
+static void cmdq_task_remove_wfe(struct cmdq_task *task)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ u64 *base = task->pkt->va_base;
+ int i;
+
+ dma_sync_single_for_cpu(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+ for (i = 0; i < CMDQ_NUM_CMD(task->pkt); i++)
+ if (cmdq_command_is_wfe(base[i]))
+ base[i] = (u64)CMDQ_JUMP_BY_OFFSET << 32 |
+ CMDQ_JUMP_PASS;
+ dma_sync_single_for_device(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+}
+
+static bool cmdq_thread_is_in_wfe(struct cmdq_thread *thread)
+{
+ return readl(thread->base + CMDQ_THR_WAIT_TOKEN) & CMDQ_THR_IS_WAITING;
+}
+
+static void cmdq_thread_wait_end(struct cmdq_thread *thread,
+ unsigned long end_pa)
+{
+ struct device *dev = thread->chan->mbox->dev;
+ unsigned long curr_pa;
+
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_ADDR,
+ curr_pa, curr_pa == end_pa, 1, 20))
+ dev_err(dev, "GCE thread cannot run to end.\n");
+}
+
+static void cmdq_task_exec(struct cmdq_pkt *pkt, struct cmdq_thread *thread)
+{
+ struct cmdq *cmdq;
+ struct cmdq_task *task;
+ unsigned long curr_pa, end_pa;
+
+ cmdq = dev_get_drvdata(thread->chan->mbox->dev);
+
+ /* Client should not flush new tasks if suspended. */
+ WARN_ON(cmdq->suspended);
+
+ task = kzalloc(sizeof(*task), GFP_ATOMIC);
+ task->cmdq = cmdq;
+ INIT_LIST_HEAD(&task->list_entry);
+ task->pa_base = dma_map_single(cmdq->mbox.dev, pkt->va_base,
+ pkt->cmd_buf_size, DMA_TO_DEVICE);
+ task->thread = thread;
+ task->pkt = pkt;
+
+ if (list_empty(&thread->task_busy_list)) {
+ WARN_ON(clk_enable(cmdq->clock) < 0);
+ WARN_ON(cmdq_thread_reset(cmdq, thread) < 0);
+
+ writel(task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+ writel(task->pa_base + pkt->cmd_buf_size,
+ thread->base + CMDQ_THR_END_ADDR);
+ writel(CMDQ_THR_IRQ_EN, thread->base + CMDQ_THR_IRQ_ENABLE);
+ writel(CMDQ_THR_ENABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+
+ mod_timer(&thread->timeout,
+ jiffies + msecs_to_jiffies(CMDQ_TIMEOUT_MS));
+ } else {
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+ curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+ end_pa = readl(thread->base + CMDQ_THR_END_ADDR);
+
+ /*
+ * Atomic execution should remove the following wfe, i.e. only
+ * wait event at first task, and prevent to pause when running.
+ */
+ if (thread->atomic_exec) {
+ /* GCE is executing if command is not WFE */
+ if (!cmdq_thread_is_in_wfe(thread)) {
+ cmdq_thread_resume(thread);
+ cmdq_thread_wait_end(thread, end_pa);
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+ /* set to this task directly */
+ writel(task->pa_base,
+ thread->base + CMDQ_THR_CURR_ADDR);
+ } else {
+ cmdq_task_insert_into_thread(task);
+ cmdq_task_remove_wfe(task);
+ smp_mb(); /* modify jump before enable thread */
+ }
+ } else {
+ /* check boundary */
+ if (curr_pa == end_pa - CMDQ_INST_SIZE ||
+ curr_pa == end_pa) {
+ /* set to this task directly */
+ writel(task->pa_base,
+ thread->base + CMDQ_THR_CURR_ADDR);
+ } else {
+ cmdq_task_insert_into_thread(task);
+ smp_mb(); /* modify jump before enable thread */
+ }
+ }
+ writel(task->pa_base + pkt->cmd_buf_size,
+ thread->base + CMDQ_THR_END_ADDR);
+ cmdq_thread_resume(thread);
+ }
+ list_move_tail(&task->list_entry, &thread->task_busy_list);
+}
+
+static void cmdq_task_exec_done(struct cmdq_task *task, bool err)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ struct cmdq_cb_data cmdq_cb_data;
+
+ dma_unmap_single(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+ if (task->pkt->cb.cb) {
+ cmdq_cb_data.err = err;
+ cmdq_cb_data.data = task->pkt->cb.data;
+ task->pkt->cb.cb(cmdq_cb_data);
+ }
+ list_del(&task->list_entry);
+}
+
+static void cmdq_task_handle_error(struct cmdq_task *task)
+{
+ struct cmdq_thread *thread = task->thread;
+ struct cmdq_task *next_task;
+
+ dev_err(task->cmdq->mbox.dev, "task 0x%p error\n", task);
+ WARN_ON(cmdq_thread_suspend(task->cmdq, thread) < 0);
+ next_task = list_first_entry_or_null(&thread->task_busy_list,
+ struct cmdq_task, list_entry);
+ if (next_task)
+ writel(next_task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+ cmdq_thread_resume(thread);
+}
+
+static void cmdq_thread_irq_handler(struct cmdq *cmdq,
+ struct cmdq_thread *thread)
+{
+ struct cmdq_task *task, *tmp, *curr_task = NULL;
+ u32 curr_pa, irq_flag, task_end_pa;
+ bool err;
+
+ irq_flag = readl(thread->base + CMDQ_THR_IRQ_STATUS);
+ writel(~irq_flag, thread->base + CMDQ_THR_IRQ_STATUS);
+
+ /*
+ * When ISR call this function, another CPU core could run
+ * "release task" right before we acquire the spin lock, and thus
+ * reset / disable this GCE thread, so we need to check the enable
+ * bit of this GCE thread.
+ */
+ if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+ return;
+
+ if (irq_flag & CMDQ_THR_IRQ_ERROR)
+ err = true;
+ else if (irq_flag & CMDQ_THR_IRQ_DONE)
+ err = false;
+ else
+ return;
+
+ curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+
+ list_for_each_entry_safe(task, tmp, &thread->task_busy_list,
+ list_entry) {
+ task_end_pa = task->pa_base + task->pkt->cmd_buf_size;
+ if (curr_pa >= task->pa_base && curr_pa < task_end_pa)
+ curr_task = task;
+
+ if (!curr_task || curr_pa == task_end_pa - CMDQ_INST_SIZE) {
+ cmdq_task_exec_done(task, false);
+ kfree(task);
+ } else if (err) {
+ cmdq_task_exec_done(task, true);
+ cmdq_task_handle_error(curr_task);
+ kfree(task);
+ }
+
+ if (curr_task)
+ break;
+ }
+
+ if (list_empty(&thread->task_busy_list)) {
+ cmdq_thread_disable(cmdq, thread);
+ clk_disable(cmdq->clock);
+ } else {
+ mod_timer(&thread->timeout,
+ jiffies + msecs_to_jiffies(CMDQ_TIMEOUT_MS));
+ }
+}
+
+static irqreturn_t cmdq_irq_handler(int irq, void *dev)
+{
+ struct cmdq *cmdq = dev;
+ unsigned long irq_status, flags = 0L;
+ int bit;
+
+ irq_status = readl(cmdq->base + CMDQ_CURR_IRQ_STATUS) & CMDQ_IRQ_MASK;
+ if (!(irq_status ^ CMDQ_IRQ_MASK))
+ return IRQ_NONE;
+
+ for_each_clear_bit(bit, &irq_status, fls(CMDQ_IRQ_MASK)) {
+ struct cmdq_thread *thread = &cmdq->thread[bit];
+
+ spin_lock_irqsave(&thread->chan->lock, flags);
+ cmdq_thread_irq_handler(cmdq, thread);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+ }
+ return IRQ_HANDLED;
+}
+
+static void cmdq_thread_handle_timeout(unsigned long data)
+{
+ struct cmdq_thread *thread = (struct cmdq_thread *)data;
+ struct cmdq *cmdq = container_of(thread->chan->mbox, struct cmdq, mbox);
+ struct cmdq_task *task, *tmp;
+ unsigned long flags;
+
+ spin_lock_irqsave(&thread->chan->lock, flags);
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+
+ /*
+ * Although IRQ is disabled, GCE continues to execute.
+ * It may have pending IRQ before GCE thread is suspended,
+ * so check this condition again.
+ */
+ cmdq_thread_irq_handler(cmdq, thread);
+
+ if (list_empty(&thread->task_busy_list)) {
+ cmdq_thread_resume(thread);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+ return;
+ }
+
+ dev_err(cmdq->mbox.dev, "timeout\n");
+ list_for_each_entry_safe(task, tmp, &thread->task_busy_list,
+ list_entry) {
+ cmdq_task_exec_done(task, true);
+ kfree(task);
+ }
+
+ cmdq_thread_resume(thread);
+ cmdq_thread_disable(cmdq, thread);
+ clk_disable(cmdq->clock);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+}
+
+static int cmdq_suspend(struct device *dev)
+{
+ struct cmdq *cmdq = dev_get_drvdata(dev);
+ struct cmdq_thread *thread;
+ int i;
+ bool task_running = false;
+
+ cmdq->suspended = true;
+
+ for (i = 0; i < ARRAY_SIZE(cmdq->thread); i++) {
+ thread = &cmdq->thread[i];
+ if (!list_empty(&thread->task_busy_list)) {
+ task_running = true;
+ break;
+ }
+ }
+
+ if (task_running)
+ dev_warn(dev, "exist running task(s) in suspend\n");
+
+ clk_unprepare(cmdq->clock);
+ return 0;
+}
+
+static int cmdq_resume(struct device *dev)
+{
+ struct cmdq *cmdq = dev_get_drvdata(dev);
+
+ WARN_ON(clk_prepare(cmdq->clock) < 0);
+ cmdq->suspended = false;
+ return 0;
+}
+
+static int cmdq_remove(struct platform_device *pdev)
+{
+ struct cmdq *cmdq = platform_get_drvdata(pdev);
+
+ mbox_controller_unregister(&cmdq->mbox);
+ clk_unprepare(cmdq->clock);
+ return 0;
+}
+
+static int cmdq_mbox_send_data(struct mbox_chan *chan, void *data)
+{
+ cmdq_task_exec(data, chan->con_priv);
+ return 0;
+}
+
+static int cmdq_mbox_startup(struct mbox_chan *chan)
+{
+ return 0;
+}
+
+static void cmdq_mbox_shutdown(struct mbox_chan *chan)
+{
+}
+
+static bool cmdq_mbox_last_tx_done(struct mbox_chan *chan)
+{
+ return true;
+}
+
+static const struct mbox_chan_ops cmdq_mbox_chan_ops = {
+ .send_data = cmdq_mbox_send_data,
+ .startup = cmdq_mbox_startup,
+ .shutdown = cmdq_mbox_shutdown,
+ .last_tx_done = cmdq_mbox_last_tx_done,
+};
+
+static struct mbox_chan *cmdq_xlate(struct mbox_controller *mbox,
+ const struct of_phandle_args *sp)
+{
+ int ind = sp->args[0];
+ struct cmdq_thread *thread;
+
+ if (ind >= mbox->num_chans)
+ return ERR_PTR(-EINVAL);
+
+ thread = mbox->chans[ind].con_priv;
+ thread->atomic_exec = (sp->args[1] != 0);
+ thread->chan = &mbox->chans[ind];
+
+ return &mbox->chans[ind];
+}
+
+static int cmdq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct cmdq *cmdq;
+ int err, i;
+
+ cmdq = devm_kzalloc(dev, sizeof(*cmdq), GFP_KERNEL);
+ if (!cmdq)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ cmdq->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(cmdq->base)) {
+ dev_err(dev, "failed to ioremap gce\n");
+ return PTR_ERR(cmdq->base);
+ }
+
+ cmdq->irq = platform_get_irq(pdev, 0);
+ if (!cmdq->irq) {
+ dev_err(dev, "failed to get irq\n");
+ return -EINVAL;
+ }
+ err = devm_request_irq(dev, cmdq->irq, cmdq_irq_handler, IRQF_SHARED,
+ "mtk_cmdq", cmdq);
+ if (err < 0) {
+ dev_err(dev, "failed to register ISR (%d)\n", err);
+ return err;
+ }
+
+ dev_dbg(dev, "cmdq device: addr:0x%p, va:0x%p, irq:%d\n",
+ dev, cmdq->base, cmdq->irq);
+
+ cmdq->clock = devm_clk_get(dev, "gce");
+ if (IS_ERR(cmdq->clock)) {
+ dev_err(dev, "failed to get gce clk\n");
+ return PTR_ERR(cmdq->clock);
+ }
+
+ cmdq->mbox.dev = dev;
+ cmdq->mbox.chans = devm_kcalloc(dev, CMDQ_THR_MAX_COUNT,
+ sizeof(*cmdq->mbox.chans), GFP_KERNEL);
+ if (!cmdq->mbox.chans)
+ return -ENOMEM;
+
+ cmdq->mbox.num_chans = CMDQ_THR_MAX_COUNT;
+ cmdq->mbox.ops = &cmdq_mbox_chan_ops;
+ cmdq->mbox.of_xlate = cmdq_xlate;
+
+ /* make use of TXDONE_BY_ACK */
+ cmdq->mbox.txdone_irq = false;
+ cmdq->mbox.txdone_poll = false;
+
+ for (i = 0; i < ARRAY_SIZE(cmdq->thread); i++) {
+ cmdq->thread[i].base = cmdq->base + CMDQ_THR_BASE +
+ CMDQ_THR_SIZE * i;
+ INIT_LIST_HEAD(&cmdq->thread[i].task_busy_list);
+ init_timer(&cmdq->thread[i].timeout);
+ cmdq->thread[i].timeout.function = cmdq_thread_handle_timeout;
+ cmdq->thread[i].timeout.data = (unsigned long)&cmdq->thread[i];
+ cmdq->mbox.chans[i].con_priv = &cmdq->thread[i];
+ }
+
+ err = mbox_controller_register(&cmdq->mbox);
+ if (err < 0) {
+ dev_err(dev, "failed to register mailbox: %d\n", err);
+ return err;
+ }
+
+ platform_set_drvdata(pdev, cmdq);
+ WARN_ON(clk_prepare(cmdq->clock) < 0);
+
+ return 0;
+}
+
+static const struct dev_pm_ops cmdq_pm_ops = {
+ .suspend = cmdq_suspend,
+ .resume = cmdq_resume,
+};
+
+static const struct of_device_id cmdq_of_ids[] = {
+ {.compatible = "mediatek,mt8173-gce",},
+ {}
+};
+
+static struct platform_driver cmdq_drv = {
+ .probe = cmdq_probe,
+ .remove = cmdq_remove,
+ .driver = {
+ .name = "mtk_cmdq",
+ .pm = &cmdq_pm_ops,
+ .of_match_table = cmdq_of_ids,
+ }
+};
+
+builtin_platform_driver(cmdq_drv);
diff --git a/include/linux/mailbox/mtk-cmdq-mailbox.h b/include/linux/mailbox/mtk-cmdq-mailbox.h
new file mode 100644
index 0000000..3433c64
--- /dev/null
+++ b/include/linux/mailbox/mtk-cmdq-mailbox.h
@@ -0,0 +1,75 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MTK_CMDQ_MAILBOX_H__
+#define __MTK_CMDQ_MAILBOX_H__
+
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define CMDQ_INST_SIZE 8 /* instruction is 64-bit */
+#define CMDQ_OP_CODE_SHIFT 24
+#define CMDQ_JUMP_PASS CMDQ_INST_SIZE
+
+#define CMDQ_WFE_UPDATE BIT(31)
+#define CMDQ_WFE_WAIT BIT(15)
+#define CMDQ_WFE_WAIT_VALUE 0x1
+
+/*
+ * CMDQ_CODE_MASK:
+ * set write mask
+ * format: op mask
+ * CMDQ_CODE_WRITE:
+ * write value into target register
+ * format: op subsys address value
+ * CMDQ_CODE_JUMP:
+ * jump by offset
+ * format: op offset
+ * CMDQ_CODE_WFE:
+ * wait for event and clear
+ * it is just clear if no wait
+ * format: [wait] op event update:1 to_wait:1 wait:1
+ * [clear] op event update:1 to_wait:0 wait:0
+ * CMDQ_CODE_EOC:
+ * end of command
+ * format: op irq_flag
+ */
+enum cmdq_code {
+ CMDQ_CODE_MASK = 0x02,
+ CMDQ_CODE_WRITE = 0x04,
+ CMDQ_CODE_JUMP = 0x10,
+ CMDQ_CODE_WFE = 0x20,
+ CMDQ_CODE_EOC = 0x40,
+};
+
+struct cmdq_cb_data {
+ bool err;
+ void *data;
+};
+
+typedef void (*cmdq_async_flush_cb)(struct cmdq_cb_data data);
+
+struct cmdq_task_cb {
+ cmdq_async_flush_cb cb;
+ void *data;
+};
+
+struct cmdq_pkt {
+ void *va_base;
+ size_t cmd_buf_size; /* command occupied size */
+ size_t buf_size; /* real buffer size */
+ struct cmdq_task_cb cb;
+};
+
+#endif /* __MTK_CMDQ_MAILBOX_H__ */
--
1.9.1
^ permalink raw reply related
* [PATCH v19 3/4] arm64: dts: mt8173: Add GCE node
From: HS Liao @ 2017-01-03 3:05 UTC (permalink / raw)
To: Rob Herring, Matthias Brugger, Jassi Brar
Cc: Daniel Kurtz, Sascha Hauer, devicetree, linux-kernel,
linux-arm-kernel, linux-mediatek, srv_heupstream, Sascha Hauer,
Philipp Zabel, Nicolas Boichat, CK HU, cawa cheng, Bibby Hsieh,
YT Shen, Daoyuan Huang, Damon Chu, Josh-YC Liu, Glory Hung,
Jiaguang Zhang, Dennis-YC Hsieh
In-Reply-To: <1483412751-28690-1-git-send-email-hs.liao@mediatek.com>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 12e7027..9f93447 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -422,6 +422,16 @@
status = "disabled";
};
+ gce: gce@10212000 {
+ compatible = "mediatek,mt8173-gce";
+ reg = <0 0x10212000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_GCE>;
+ clock-names = "gce";
+
+ #mbox-cells = <2>;
+ };
+
mipi_tx0: mipi-dphy@10215000 {
compatible = "mediatek,mt8173-mipi-tx";
reg = <0 0x10215000 0 0x1000>;
--
1.9.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox