* Re: [PATCH 2/3] devicetree: bq27425: add documentation for bq27425 fuel gauge
From: Matt Ranostay @ 2017-01-04 5:23 UTC (permalink / raw)
To: Rob Herring; +Cc: devicetree, linux-pm, Sebastian Reichel, Tony Lindgren
In-Reply-To: <20170103164715.pypb5zt22hg4zqlh@rob-hp-laptop>
On Tue, Jan 3, 2017 at 8:47 AM, Rob Herring <robh@kernel.org> wrote:
> On Sun, Dec 25, 2016 at 09:44:41PM -0800, Matt Ranostay wrote:
>> Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
>> ---
>> .../devicetree/bindings/power/bq27425.txt | 25 ++++++++++++++++++++++
>> 1 file changed, 25 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/power/bq27425.txt
>>
>> diff --git a/Documentation/devicetree/bindings/power/bq27425.txt b/Documentation/devicetree/bindings/power/bq27425.txt
>> new file mode 100644
>> index 000000000000..f09f787a9378
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/power/bq27425.txt
>> @@ -0,0 +1,25 @@
>> +* TI BQ27425 Fuel Gauge
>> +
>> +http://www.ti.com/lit/ds/symlink/bq27425-g2a.pdf
>> +
>> +Please note that if any of the optional properties are defined
>> +then all settings must be.
>> +
>> +Required properties:
>> +- compatible: Should be "ti,bq27425"
>> +- reg: integer, i2c of the device
>
> s/i2c/I2C address/
>
>> +
>> +Optional properties:
>> +- ti,design-capacity: integer of mAh of the battery
>> +- ti,design-energy: integer of the mWh of the battery
>> +- ti,terminate-voltage: integer of mV of the dead voltage of
>> + the battery
>
> These all need unit suffixes. mAh and mWh may need to be added to
> property-units.txt.
Ok makes sense.
>
>> +
>> +bq27425 {
>> + compatible = "ti,bq27425";
>> + reg = <0x55>;
>> +
>> + ti,design-capacity = <1360>;
>> + ti,design-energy = <4970>;
>> + ti,terminate-voltage = <3200>;
>> +};
>> --
>> 2.7.4
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe devicetree" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v5 1/4] soc: zte: Add header for PM domains specifiers
From: Shawn Guo @ 2017-01-04 5:29 UTC (permalink / raw)
To: Baoyou Xie
Cc: mark.rutland, jun.nie, geert+renesas, linus.walleij, f.fainelli,
pankaj.dubey, krzk, chen.chaokai, wang.qiang01, linux, devicetree,
arnd, xie.baoyou, claudiu.manoil, robh+dt, mchehab,
laurent.pinchart+renesas, linux-arm-kernel, gregkh, linux-kernel,
yangbo.lu, akpm, davem
In-Reply-To: <1483489157-10782-1-git-send-email-baoyou.xie@linaro.org>
On Wed, Jan 04, 2017 at 08:19:14AM +0800, Baoyou Xie wrote:
> This patch adds header with values used for ZTE 2967
> SoC's power domain driver.
>
> Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
> Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
The tags like Reviewed-by, Acked-by etc, can only be added into your
patch after people give it explicitly. One of the examples is that Jun
Nie gave his Reviewed-by tag on your "[PATCH v2 2/2] soc: zte:
pm_domains: Add support for zx296718 board".
https://www.spinics.net/lists/arm-kernel/msg547282.html
I did not give my Reviewed-by tag on list, so you shouldn't add it here.
Actually, in case of this patch series, I will probably apply them
through ZTE -> arm-soc tree, when I feel it's ready. So I'm do not even
need to give the Reviewed-by tag.
Shawn
> ---
> include/dt-bindings/soc/zte,pm_domains.h | 23 +++++++++++++++++++++++
> 1 file changed, 23 insertions(+)
> create mode 100644 include/dt-bindings/soc/zte,pm_domains.h
>
> diff --git a/include/dt-bindings/soc/zte,pm_domains.h b/include/dt-bindings/soc/zte,pm_domains.h
> new file mode 100644
> index 0000000..01e9abc
> --- /dev/null
> +++ b/include/dt-bindings/soc/zte,pm_domains.h
> @@ -0,0 +1,23 @@
> +/*
> + * Copyright (C) 2017 Linaro Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie@linaro.org>
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +#ifndef _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H
> +#define _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H
> +
> +#define DM_ZX296718_SAPPU 0
> +#define DM_ZX296718_VDE 1 /* g1v6 */
> +#define DM_ZX296718_VCE 2 /* h1v6 */
> +#define DM_ZX296718_HDE 3 /* g2v2 */
> +#define DM_ZX296718_VIU 4
> +#define DM_ZX296718_USB20 5
> +#define DM_ZX296718_USB21 6
> +#define DM_ZX296718_USB30 7
> +#define DM_ZX296718_HSIC 8
> +#define DM_ZX296718_GMAC 9
> +#define DM_ZX296718_TS 10
> +#define DM_ZX296718_VOU 11
> +
> +#endif /* _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H */
> --
> 2.7.4
>
^ permalink raw reply
* [PATCH v3 0/2] Broadcom FlexRM ring manager support
From: Anup Patel @ 2017-01-04 5:34 UTC (permalink / raw)
To: Jassi Brar, Rob Herring
Cc: Mark Rutland, Ray Jui, Scott Branden, Pramod KUMAR, Rob Rice,
devicetree, linux-kernel, linux-arm-kernel,
bcm-kernel-feedback-list, Anup Patel
The Broadcom FlexRM ring manager provides producer-consumer style
ring interface for offload engines on Broadcom iProc SoCs. We can
have one or more instances of Broadcom FlexRM ring manager in a SoC.
This patchset adds a mailbox driver for Broadcom FlexRM ring manager
which can be used by offload engine drivers as mailbox clients.
The Broadcom FlexRM mailbox driver is feature complete for RAID and
Crypto offload engines. We will have incremental patches in-future
for ring-level statistics using debugfs and minor optimizations.
This patchset is based on Linux-4.10-rc2 and it is also available
at flexrm-v3 branch of https://github.com/Broadcom/arm64-linux.git
Changes since v2:
- Rebased patches for Linux-4.10-rc2
Changes since v1:
- Use compatile string as brcm,iproc-flexrm-mbox
- Rephrase commit message and text in DT bindings patch
Anup Patel (2):
mailbox: Add driver for Broadcom FlexRM ring manager
dt-bindings: Add DT bindings info for FlexRM ring manager
.../bindings/mailbox/brcm,iproc-flexrm-mbox.txt | 60 ++
drivers/mailbox/Kconfig | 11 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mailbox-flexrm/Makefile | 6 +
drivers/mailbox/mailbox-flexrm/flexrm-desc.c | 764 +++++++++++++++++++
drivers/mailbox/mailbox-flexrm/flexrm-desc.h | 47 ++
drivers/mailbox/mailbox-flexrm/flexrm-main.c | 829 +++++++++++++++++++++
include/linux/mailbox/brcm-message.h | 14 +-
8 files changed, 1729 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt
create mode 100644 drivers/mailbox/mailbox-flexrm/Makefile
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-desc.c
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-desc.h
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-main.c
--
2.7.4
^ permalink raw reply
* [PATCH v3 1/2] mailbox: Add driver for Broadcom FlexRM ring manager
From: Anup Patel @ 2017-01-04 5:34 UTC (permalink / raw)
To: Jassi Brar, Rob Herring
Cc: Mark Rutland, Ray Jui, Scott Branden, Pramod KUMAR, Rob Rice,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w, Anup Patel
In-Reply-To: <1483508082-7008-1-git-send-email-anup.patel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Some of the Broadcom iProc SoCs have FlexRM ring manager
which provides a ring-based programming interface to various
offload engines (e.g. RAID, Crypto, etc).
This patch adds a common mailbox driver for Broadcom FlexRM
ring manager which can be shared by various offload engine
drivers (implemented as mailbox clients).
Reviewed-by: Ray Jui <ray.jui-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Reviewed-by: Scott Branden <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Reviewed-by: Pramod KUMAR <pramod.kumar-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Signed-off-by: Anup Patel <anup.patel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
drivers/mailbox/Kconfig | 11 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mailbox-flexrm/Makefile | 6 +
drivers/mailbox/mailbox-flexrm/flexrm-desc.c | 764 ++++++++++++++++++++++++
drivers/mailbox/mailbox-flexrm/flexrm-desc.h | 47 ++
drivers/mailbox/mailbox-flexrm/flexrm-main.c | 829 +++++++++++++++++++++++++++
include/linux/mailbox/brcm-message.h | 14 +-
7 files changed, 1669 insertions(+), 4 deletions(-)
create mode 100644 drivers/mailbox/mailbox-flexrm/Makefile
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-desc.c
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-desc.h
create mode 100644 drivers/mailbox/mailbox-flexrm/flexrm-main.c
diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index ceff415..305018c 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -152,4 +152,15 @@ config BCM_PDC_MBOX
Mailbox implementation for the Broadcom PDC ring manager,
which provides access to various offload engines on Broadcom
SoCs. Say Y here if you want to use the Broadcom PDC.
+
+config BCM_FLEXRM_MBOX
+ tristate "Broadcom FlexRM Mailbox"
+ depends on ARM64 || COMPILE_TEST
+ depends on HAS_DMA
+ select GENERIC_MSI_IRQ_DOMAIN
+ default ARCH_BCM_IPROC
+ help
+ Mailbox implementation of the Broadcom FlexRM ring manager,
+ which provides access to various offload engines on Broadcom
+ SoCs. Say Y here if you want to use the Broadcom FlexRM.
endif
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index 7dde4f6..45083c0 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -30,4 +30,6 @@ obj-$(CONFIG_HI6220_MBOX) += hi6220-mailbox.o
obj-$(CONFIG_BCM_PDC_MBOX) += bcm-pdc-mailbox.o
+obj-$(CONFIG_BCM_FLEXRM_MBOX) += mailbox-flexrm/
+
obj-$(CONFIG_TEGRA_HSP_MBOX) += tegra-hsp.o
diff --git a/drivers/mailbox/mailbox-flexrm/Makefile b/drivers/mailbox/mailbox-flexrm/Makefile
new file mode 100644
index 0000000..f5bf069
--- /dev/null
+++ b/drivers/mailbox/mailbox-flexrm/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for Broadcom FlexRM Mailbox Driver.
+#
+
+flexrm-mbox-objs := flexrm-main.o flexrm-desc.o
+obj-$(CONFIG_BCM_FLEXRM_MBOX) += flexrm-mbox.o
diff --git a/drivers/mailbox/mailbox-flexrm/flexrm-desc.c b/drivers/mailbox/mailbox-flexrm/flexrm-desc.c
new file mode 100644
index 0000000..b0449eb
--- /dev/null
+++ b/drivers/mailbox/mailbox-flexrm/flexrm-desc.c
@@ -0,0 +1,764 @@
+/* Broadcom FlexRM Mailbox Driver
+ *
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * FlexRM descriptor library
+ */
+
+#include <asm/barrier.h>
+#include <asm/byteorder.h>
+#include <linux/dma-mapping.h>
+#include <linux/printk.h>
+
+#include "flexrm-desc.h"
+
+/* Completion descriptor format */
+#define CMPL_OPAQUE_SHIFT 0
+#define CMPL_OPAQUE_MASK 0xffff
+#define CMPL_ENGINE_STATUS_SHIFT 16
+#define CMPL_ENGINE_STATUS_MASK 0xffff
+#define CMPL_DME_STATUS_SHIFT 32
+#define CMPL_DME_STATUS_MASK 0xffff
+#define CMPL_RM_STATUS_SHIFT 48
+#define CMPL_RM_STATUS_MASK 0xffff
+
+/* Completion DME status code */
+#define DME_STATUS_MEM_COR_ERR BIT(0)
+#define DME_STATUS_MEM_UCOR_ERR BIT(1)
+#define DME_STATUS_FIFO_UNDERFLOW BIT(2)
+#define DME_STATUS_FIFO_OVERFLOW BIT(3)
+#define DME_STATUS_RRESP_ERR BIT(4)
+#define DME_STATUS_BRESP_ERR BIT(5)
+#define DME_STATUS_ERROR_MASK (DME_STATUS_MEM_COR_ERR | \
+ DME_STATUS_MEM_UCOR_ERR | \
+ DME_STATUS_FIFO_UNDERFLOW | \
+ DME_STATUS_FIFO_OVERFLOW | \
+ DME_STATUS_RRESP_ERR | \
+ DME_STATUS_BRESP_ERR)
+
+/* Completion RM status code */
+#define RM_STATUS_CODE_SHIFT 0
+#define RM_STATUS_CODE_MASK 0x3ff
+#define RM_STATUS_CODE_GOOD 0x0
+#define RM_STATUS_CODE_AE_TIMEOUT 0x3ff
+
+/* General descriptor format */
+#define DESC_TYPE_SHIFT 60
+#define DESC_TYPE_MASK 0xf
+#define DESC_PAYLOAD_SHIFT 0
+#define DESC_PAYLOAD_MASK 0x0fffffffffffffff
+
+/* Null descriptor format */
+#define NULL_TYPE 0
+#define NULL_TOGGLE_SHIFT 58
+#define NULL_TOGGLE_MASK 0x1
+
+/* Header descriptor format */
+#define HEADER_TYPE 1
+#define HEADER_TOGGLE_SHIFT 58
+#define HEADER_TOGGLE_MASK 0x1
+#define HEADER_ENDPKT_SHIFT 57
+#define HEADER_ENDPKT_MASK 0x1
+#define HEADER_STARTPKT_SHIFT 56
+#define HEADER_STARTPKT_MASK 0x1
+#define HEADER_BDCOUNT_SHIFT 36
+#define HEADER_BDCOUNT_MASK 0x1f
+#define HEADER_BDCOUNT_MAX HEADER_BDCOUNT_MASK
+#define HEADER_FLAGS_SHIFT 16
+#define HEADER_FLAGS_MASK 0xffff
+#define HEADER_OPAQUE_SHIFT 0
+#define HEADER_OPAQUE_MASK 0xffff
+
+/* Source (SRC) descriptor format */
+#define SRC_TYPE 2
+#define SRC_LENGTH_SHIFT 44
+#define SRC_LENGTH_MASK 0xffff
+#define SRC_ADDR_SHIFT 0
+#define SRC_ADDR_MASK 0x00000fffffffffff
+
+/* Destination (DST) descriptor format */
+#define DST_TYPE 3
+#define DST_LENGTH_SHIFT 44
+#define DST_LENGTH_MASK 0xffff
+#define DST_ADDR_SHIFT 0
+#define DST_ADDR_MASK 0x00000fffffffffff
+
+/* Immediate (IMM) descriptor format */
+#define IMM_TYPE 4
+#define IMM_DATA_SHIFT 0
+#define IMM_DATA_MASK 0x0fffffffffffffff
+
+/* Next pointer (NPTR) descriptor format */
+#define NPTR_TYPE 5
+#define NPTR_TOGGLE_SHIFT 58
+#define NPTR_TOGGLE_MASK 0x1
+#define NPTR_ADDR_SHIFT 0
+#define NPTR_ADDR_MASK 0x00000fffffffffff
+
+/* Mega source (MSRC) descriptor format */
+#define MSRC_TYPE 6
+#define MSRC_LENGTH_SHIFT 44
+#define MSRC_LENGTH_MASK 0xffff
+#define MSRC_ADDR_SHIFT 0
+#define MSRC_ADDR_MASK 0x00000fffffffffff
+
+/* Mega destination (MDST) descriptor format */
+#define MDST_TYPE 7
+#define MDST_LENGTH_SHIFT 44
+#define MDST_LENGTH_MASK 0xffff
+#define MDST_ADDR_SHIFT 0
+#define MDST_ADDR_MASK 0x00000fffffffffff
+
+/* Source with tlast (SRCT) descriptor format */
+#define SRCT_TYPE 8
+#define SRCT_LENGTH_SHIFT 44
+#define SRCT_LENGTH_MASK 0xffff
+#define SRCT_ADDR_SHIFT 0
+#define SRCT_ADDR_MASK 0x00000fffffffffff
+
+/* Destination with tlast (DSTT) descriptor format */
+#define DSTT_TYPE 9
+#define DSTT_LENGTH_SHIFT 44
+#define DSTT_LENGTH_MASK 0xffff
+#define DSTT_ADDR_SHIFT 0
+#define DSTT_ADDR_MASK 0x00000fffffffffff
+
+/* Immediate with tlast (IMMT) descriptor format */
+#define IMMT_TYPE 10
+#define IMMT_DATA_SHIFT 0
+#define IMMT_DATA_MASK 0x0fffffffffffffff
+
+/* Descriptor helper macros */
+#define DESC_DEC(_d, _s, _m) (((_d) >> (_s)) & (_m))
+#define DESC_ENC(_d, _v, _s, _m) \
+ do { \
+ (_d) &= ~((u64)(_m) << (_s)); \
+ (_d) |= (((u64)(_v) & (_m)) << (_s)); \
+ } while (0)
+
+u64 flexrm_read_desc(void *desc_ptr)
+{
+ return le64_to_cpu(*((u64 *)desc_ptr));
+}
+
+void flexrm_write_desc(void *desc_ptr, u64 desc)
+{
+ *((u64 *)desc_ptr) = cpu_to_le64(desc);
+}
+
+u32 flexrm_cmpl_desc_to_reqid(u64 cmpl_desc)
+{
+ return (u32)(cmpl_desc & CMPL_OPAQUE_MASK);
+}
+
+int flexrm_cmpl_desc_to_error(u64 cmpl_desc)
+{
+ u32 status;
+
+ status = DESC_DEC(cmpl_desc, CMPL_DME_STATUS_SHIFT,
+ CMPL_DME_STATUS_MASK);
+ if (status & DME_STATUS_ERROR_MASK)
+ return -EIO;
+
+ status = DESC_DEC(cmpl_desc, CMPL_RM_STATUS_SHIFT,
+ CMPL_RM_STATUS_MASK);
+ status &= RM_STATUS_CODE_MASK;
+ if (status == RM_STATUS_CODE_AE_TIMEOUT)
+ return -ETIMEDOUT;
+
+ return 0;
+}
+
+bool flexrm_is_next_table_desc(void *desc_ptr)
+{
+ u64 desc = flexrm_read_desc(desc_ptr);
+ u32 type = DESC_DEC(desc, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+
+ return (type == NPTR_TYPE) ? true : false;
+}
+
+u64 flexrm_next_table_desc(u32 toggle, dma_addr_t next_addr)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, NPTR_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, toggle, NPTR_TOGGLE_SHIFT, NPTR_TOGGLE_MASK);
+ DESC_ENC(desc, next_addr, NPTR_ADDR_SHIFT, NPTR_ADDR_MASK);
+
+ return desc;
+}
+
+u64 flexrm_null_desc(u32 toggle)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, NULL_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, toggle, NULL_TOGGLE_SHIFT, NULL_TOGGLE_MASK);
+
+ return desc;
+}
+
+u32 flexrm_estimate_header_desc_count(u32 nhcnt)
+{
+ u32 hcnt = nhcnt / HEADER_BDCOUNT_MAX;
+
+ if (!(nhcnt % HEADER_BDCOUNT_MAX))
+ hcnt += 1;
+
+ return hcnt;
+}
+
+static void flexrm_flip_header_toogle(void *desc_ptr)
+{
+ u64 desc = flexrm_read_desc(desc_ptr);
+
+ if (desc & ((u64)0x1 << HEADER_TOGGLE_SHIFT))
+ desc &= ~((u64)0x1 << HEADER_TOGGLE_SHIFT);
+ else
+ desc |= ((u64)0x1 << HEADER_TOGGLE_SHIFT);
+
+ flexrm_write_desc(desc_ptr, desc);
+}
+
+static u64 flexrm_header_desc(u32 toggle, u32 startpkt, u32 endpkt,
+ u32 bdcount, u32 flags, u32 opaque)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, HEADER_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, toggle, HEADER_TOGGLE_SHIFT, HEADER_TOGGLE_MASK);
+ DESC_ENC(desc, startpkt, HEADER_STARTPKT_SHIFT, HEADER_STARTPKT_MASK);
+ DESC_ENC(desc, endpkt, HEADER_ENDPKT_SHIFT, HEADER_ENDPKT_MASK);
+ DESC_ENC(desc, bdcount, HEADER_BDCOUNT_SHIFT, HEADER_BDCOUNT_MASK);
+ DESC_ENC(desc, flags, HEADER_FLAGS_SHIFT, HEADER_FLAGS_MASK);
+ DESC_ENC(desc, opaque, HEADER_OPAQUE_SHIFT, HEADER_OPAQUE_MASK);
+
+ return desc;
+}
+
+static void flexrm_enqueue_desc(u32 nhpos, u32 nhcnt, u32 reqid,
+ u64 desc, void **desc_ptr, u32 *toggle,
+ void *start_desc, void *end_desc)
+{
+ u64 d;
+ u32 nhavail, _toggle, _startpkt, _endpkt, _bdcount;
+
+ /* Sanity check */
+ if (nhcnt <= nhpos)
+ return;
+
+ /*
+ * Each request or packet start with a HEADER descriptor followed
+ * by one or more non-HEADER descriptors (SRC, SRCT, MSRC, DST,
+ * DSTT, MDST, IMM, and IMMT). The number of non-HEADER descriptors
+ * following a HEADER descriptor is represented by BDCOUNT field
+ * of HEADER descriptor. The max value of BDCOUNT field is 31 which
+ * means we can only have 31 non-HEADER descriptors following one
+ * HEADER descriptor.
+ *
+ * In general use, number of non-HEADER descriptors can easily go
+ * beyond 31. To tackle this situation, we have packet (or request)
+ * extenstion bits (STARTPKT and ENDPKT) in the HEADER descriptor.
+ *
+ * To use packet extension, the first HEADER descriptor of request
+ * (or packet) will have STARTPKT=1 and ENDPKT=0. The intermediate
+ * HEADER descriptors will have STARTPKT=0 and ENDPKT=0. The last
+ * HEADER descriptor will have STARTPKT=0 and ENDPKT=1. Also, the
+ * TOGGLE bit of the first HEADER will be set to invalid state to
+ * ensure that FlexRM does not start fetching descriptors till all
+ * descriptors are enqueued. The user of this function will flip
+ * the TOGGLE bit of first HEADER after all descriptors are
+ * enqueued.
+ */
+
+ if ((nhpos % HEADER_BDCOUNT_MAX == 0) && (nhcnt - nhpos)) {
+ /* Prepare the header descriptor */
+ nhavail = (nhcnt - nhpos);
+ _toggle = (nhpos == 0) ? !(*toggle) : (*toggle);
+ _startpkt = (nhpos == 0) ? 0x1 : 0x0;
+ _endpkt = (nhavail <= HEADER_BDCOUNT_MAX) ? 0x1 : 0x0;
+ _bdcount = (nhavail <= HEADER_BDCOUNT_MAX) ?
+ nhavail : HEADER_BDCOUNT_MAX;
+ if (nhavail <= HEADER_BDCOUNT_MAX)
+ _bdcount = nhavail;
+ else
+ _bdcount = HEADER_BDCOUNT_MAX;
+ d = flexrm_header_desc(_toggle, _startpkt, _endpkt,
+ _bdcount, 0x0, reqid);
+
+ /* Write header descriptor */
+ flexrm_write_desc(*desc_ptr, d);
+
+ /* Point to next descriptor */
+ *desc_ptr += sizeof(desc);
+ if (*desc_ptr == end_desc)
+ *desc_ptr = start_desc;
+
+ /* Skip next pointer descriptors */
+ while (flexrm_is_next_table_desc(*desc_ptr)) {
+ *toggle = (*toggle) ? 0 : 1;
+ *desc_ptr += sizeof(desc);
+ if (*desc_ptr == end_desc)
+ *desc_ptr = start_desc;
+ }
+ }
+
+ /* Write desired descriptor */
+ flexrm_write_desc(*desc_ptr, desc);
+
+ /* Point to next descriptor */
+ *desc_ptr += sizeof(desc);
+ if (*desc_ptr == end_desc)
+ *desc_ptr = start_desc;
+
+ /* Skip next pointer descriptors */
+ while (flexrm_is_next_table_desc(*desc_ptr)) {
+ *toggle = (*toggle) ? 0 : 1;
+ *desc_ptr += sizeof(desc);
+ if (*desc_ptr == end_desc)
+ *desc_ptr = start_desc;
+ }
+}
+
+static u64 flexrm_src_desc(dma_addr_t addr, unsigned int length)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, SRC_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length, SRC_LENGTH_SHIFT, SRC_LENGTH_MASK);
+ DESC_ENC(desc, addr, SRC_ADDR_SHIFT, SRC_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_msrc_desc(dma_addr_t addr, unsigned int length_div_16)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, MSRC_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length_div_16, MSRC_LENGTH_SHIFT, MSRC_LENGTH_MASK);
+ DESC_ENC(desc, addr, MSRC_ADDR_SHIFT, MSRC_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_dst_desc(dma_addr_t addr, unsigned int length)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, DST_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length, DST_LENGTH_SHIFT, DST_LENGTH_MASK);
+ DESC_ENC(desc, addr, DST_ADDR_SHIFT, DST_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_mdst_desc(dma_addr_t addr, unsigned int length_div_16)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, MDST_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length_div_16, MDST_LENGTH_SHIFT, MDST_LENGTH_MASK);
+ DESC_ENC(desc, addr, MDST_ADDR_SHIFT, MDST_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_imm_desc(u64 data)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, IMM_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, data, IMM_DATA_SHIFT, IMM_DATA_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_srct_desc(dma_addr_t addr, unsigned int length)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, SRCT_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length, SRCT_LENGTH_SHIFT, SRCT_LENGTH_MASK);
+ DESC_ENC(desc, addr, SRCT_ADDR_SHIFT, SRCT_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_dstt_desc(dma_addr_t addr, unsigned int length)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, DSTT_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, length, DSTT_LENGTH_SHIFT, DSTT_LENGTH_MASK);
+ DESC_ENC(desc, addr, DSTT_ADDR_SHIFT, DSTT_ADDR_MASK);
+
+ return desc;
+}
+
+static u64 flexrm_immt_desc(u64 data)
+{
+ u64 desc = 0;
+
+ DESC_ENC(desc, IMMT_TYPE, DESC_TYPE_SHIFT, DESC_TYPE_MASK);
+ DESC_ENC(desc, data, IMMT_DATA_SHIFT, IMMT_DATA_MASK);
+
+ return desc;
+}
+
+static bool flexrm_spu_sanity_check(struct brcm_message *msg)
+{
+ struct scatterlist *sg;
+
+ if (!msg->spu.src || !msg->spu.dst)
+ return false;
+ for (sg = msg->spu.src; sg; sg = sg_next(sg)) {
+ if (sg->length & 0xf) {
+ if (sg->length > SRC_LENGTH_MASK)
+ return false;
+ } else {
+ if (sg->length > (MSRC_LENGTH_MASK * 16))
+ return false;
+ }
+ }
+ for (sg = msg->spu.dst; sg; sg = sg_next(sg)) {
+ if (sg->length & 0xf) {
+ if (sg->length > DST_LENGTH_MASK)
+ return false;
+ } else {
+ if (sg->length > (MDST_LENGTH_MASK * 16))
+ return false;
+ }
+ }
+
+ return true;
+}
+
+static u32 flexrm_spu_estimate_nonheader_desc_count(struct brcm_message *msg)
+{
+ u32 cnt = 0;
+ unsigned int dst_target = 0;
+ struct scatterlist *src_sg = msg->spu.src, *dst_sg = msg->spu.dst;
+
+ while (src_sg || dst_sg) {
+ if (src_sg) {
+ cnt++;
+ dst_target = src_sg->length;
+ src_sg = sg_next(src_sg);
+ } else
+ dst_target = UINT_MAX;
+
+ while (dst_target && dst_sg) {
+ cnt++;
+ if (dst_sg->length < dst_target)
+ dst_target -= dst_sg->length;
+ else
+ dst_target = 0;
+ dst_sg = sg_next(dst_sg);
+ }
+ }
+
+ return cnt;
+}
+
+static int flexrm_spu_dma_map(struct device *dev, struct brcm_message *msg)
+{
+ int rc;
+
+ rc = dma_map_sg(dev, msg->spu.src, sg_nents(msg->spu.src),
+ DMA_TO_DEVICE);
+ if (rc < 0)
+ return rc;
+
+ rc = dma_map_sg(dev, msg->spu.dst, sg_nents(msg->spu.dst),
+ DMA_FROM_DEVICE);
+ if (rc < 0) {
+ dma_unmap_sg(dev, msg->spu.src, sg_nents(msg->spu.src),
+ DMA_TO_DEVICE);
+ return rc;
+ }
+
+ return 0;
+}
+
+static void flexrm_spu_dma_unmap(struct device *dev, struct brcm_message *msg)
+{
+ dma_unmap_sg(dev, msg->spu.dst, sg_nents(msg->spu.dst),
+ DMA_FROM_DEVICE);
+ dma_unmap_sg(dev, msg->spu.src, sg_nents(msg->spu.src),
+ DMA_TO_DEVICE);
+}
+
+static void *flexrm_spu_write_descs(struct brcm_message *msg, u32 nhcnt,
+ u32 reqid, void *desc_ptr, u32 toggle,
+ void *start_desc, void *end_desc)
+{
+ u64 d;
+ u32 nhpos = 0;
+ void *orig_desc_ptr = desc_ptr;
+ unsigned int dst_target = 0;
+ struct scatterlist *src_sg = msg->spu.src, *dst_sg = msg->spu.dst;
+
+ while (src_sg || dst_sg) {
+ if (src_sg) {
+ if (sg_dma_len(src_sg) & 0xf)
+ d = flexrm_src_desc(sg_dma_address(src_sg),
+ sg_dma_len(src_sg));
+ else
+ d = flexrm_msrc_desc(sg_dma_address(src_sg),
+ sg_dma_len(src_sg)/16);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ dst_target = sg_dma_len(src_sg);
+ src_sg = sg_next(src_sg);
+ } else
+ dst_target = UINT_MAX;
+
+ while (dst_target && dst_sg) {
+ if (sg_dma_len(dst_sg) & 0xf)
+ d = flexrm_dst_desc(sg_dma_address(dst_sg),
+ sg_dma_len(dst_sg));
+ else
+ d = flexrm_mdst_desc(sg_dma_address(dst_sg),
+ sg_dma_len(dst_sg)/16);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ if (sg_dma_len(dst_sg) < dst_target)
+ dst_target -= sg_dma_len(dst_sg);
+ else
+ dst_target = 0;
+ dst_sg = sg_next(dst_sg);
+ }
+ }
+
+ /* Null descriptor with invalid toggle bit */
+ flexrm_write_desc(desc_ptr, flexrm_null_desc(!toggle));
+
+ /* Ensure that descriptors have been written to memory */
+ wmb();
+
+ /* Flip toggle bit in header */
+ flexrm_flip_header_toogle(orig_desc_ptr);
+
+ return desc_ptr;
+}
+
+static bool flexrm_sba_sanity_check(struct brcm_message *msg)
+{
+ u32 i;
+
+ if (!msg->sba.cmds || !msg->sba.cmds_count)
+ return false;
+
+ for (i = 0; i < msg->sba.cmds_count; i++) {
+ if (((msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_B) ||
+ (msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_C)) &&
+ (msg->sba.cmds[i].flags & BRCM_SBA_CMD_HAS_OUTPUT))
+ return false;
+ if ((msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_B) &&
+ (msg->sba.cmds[i].data_len > SRCT_LENGTH_MASK))
+ return false;
+ if ((msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_C) &&
+ (msg->sba.cmds[i].data_len > SRCT_LENGTH_MASK))
+ return false;
+ if ((msg->sba.cmds[i].flags & BRCM_SBA_CMD_HAS_RESP) &&
+ (msg->sba.cmds[i].resp_len > DSTT_LENGTH_MASK))
+ return false;
+ if ((msg->sba.cmds[i].flags & BRCM_SBA_CMD_HAS_OUTPUT) &&
+ (msg->sba.cmds[i].data_len > DSTT_LENGTH_MASK))
+ return false;
+ }
+
+ return true;
+}
+
+static u32 flexrm_sba_estimate_nonheader_desc_count(struct brcm_message *msg)
+{
+ u32 i, cnt;
+
+ cnt = 0;
+ for (i = 0; i < msg->sba.cmds_count; i++) {
+ cnt++;
+
+ if ((msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_B) ||
+ (msg->sba.cmds[i].flags & BRCM_SBA_CMD_TYPE_C))
+ cnt++;
+
+ if (msg->sba.cmds[i].flags & BRCM_SBA_CMD_HAS_RESP)
+ cnt++;
+
+ if (msg->sba.cmds[i].flags & BRCM_SBA_CMD_HAS_OUTPUT)
+ cnt++;
+ }
+
+ return cnt;
+}
+
+static void *flexrm_sba_write_descs(struct brcm_message *msg, u32 nhcnt,
+ u32 reqid, void *desc_ptr, u32 toggle,
+ void *start_desc, void *end_desc)
+{
+ u64 d;
+ u32 i, nhpos = 0;
+ struct brcm_sba_command *c;
+ void *orig_desc_ptr = desc_ptr;
+
+ /* Convert SBA commands into descriptors */
+ for (i = 0; i < msg->sba.cmds_count; i++) {
+ c = &msg->sba.cmds[i];
+
+ if ((c->flags & BRCM_SBA_CMD_HAS_RESP) &&
+ (c->flags & BRCM_SBA_CMD_HAS_OUTPUT)) {
+ /* Destination response descriptor */
+ d = flexrm_dst_desc(c->resp, c->resp_len);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ } else if (c->flags & BRCM_SBA_CMD_HAS_RESP) {
+ /* Destination response with tlast descriptor */
+ d = flexrm_dstt_desc(c->resp, c->resp_len);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ }
+
+ if (c->flags & BRCM_SBA_CMD_HAS_OUTPUT) {
+ /* Destination with tlast descriptor */
+ d = flexrm_dstt_desc(c->data, c->data_len);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ }
+
+ if (c->flags & BRCM_SBA_CMD_TYPE_B) {
+ /* Command as immediate descriptor */
+ d = flexrm_imm_desc(c->cmd);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ } else {
+ /* Command as immediate descriptor with tlast */
+ d = flexrm_immt_desc(c->cmd);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ }
+
+ if ((c->flags & BRCM_SBA_CMD_TYPE_B) ||
+ (c->flags & BRCM_SBA_CMD_TYPE_C)) {
+ /* Source with tlast descriptor */
+ d = flexrm_srct_desc(c->data, c->data_len);
+ flexrm_enqueue_desc(nhpos, nhcnt, reqid,
+ d, &desc_ptr, &toggle,
+ start_desc, end_desc);
+ nhpos++;
+ }
+ }
+
+ /* Null descriptor with invalid toggle bit */
+ flexrm_write_desc(desc_ptr, flexrm_null_desc(!toggle));
+
+ /* Ensure that descriptors have been written to memory */
+ wmb();
+
+ /* Flip toggle bit in header */
+ flexrm_flip_header_toogle(orig_desc_ptr);
+
+ return desc_ptr;
+}
+
+bool flexrm_sanity_check(struct brcm_message *msg)
+{
+ if (!msg)
+ return false;
+
+ switch (msg->type) {
+ case BRCM_MESSAGE_SPU:
+ return flexrm_spu_sanity_check(msg);
+ case BRCM_MESSAGE_SBA:
+ return flexrm_sba_sanity_check(msg);
+ default:
+ return false;
+ };
+}
+
+u32 flexrm_estimate_nonheader_desc_count(struct brcm_message *msg)
+{
+ if (!msg)
+ return 0;
+
+ switch (msg->type) {
+ case BRCM_MESSAGE_SPU:
+ return flexrm_spu_estimate_nonheader_desc_count(msg);
+ case BRCM_MESSAGE_SBA:
+ return flexrm_sba_estimate_nonheader_desc_count(msg);
+ default:
+ return 0;
+ };
+}
+
+int flexrm_dma_map(struct device *dev, struct brcm_message *msg)
+{
+ if (!dev || !msg)
+ return -EINVAL;
+
+ switch (msg->type) {
+ case BRCM_MESSAGE_SPU:
+ return flexrm_spu_dma_map(dev, msg);
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+void flexrm_dma_unmap(struct device *dev, struct brcm_message *msg)
+{
+ if (!dev || !msg)
+ return;
+
+ switch (msg->type) {
+ case BRCM_MESSAGE_SPU:
+ flexrm_spu_dma_unmap(dev, msg);
+ break;
+ default:
+ break;
+ }
+}
+
+void *flexrm_write_descs(struct brcm_message *msg, u32 nhcnt,
+ u32 reqid, void *desc_ptr, u32 toggle,
+ void *start_desc, void *end_desc)
+{
+ if (!msg || !desc_ptr || !start_desc || !end_desc)
+ return ERR_PTR(-ENOTSUPP);
+
+ if ((desc_ptr < start_desc) || (end_desc <= desc_ptr))
+ return ERR_PTR(-ERANGE);
+
+ switch (msg->type) {
+ case BRCM_MESSAGE_SPU:
+ return flexrm_spu_write_descs(msg, nhcnt, reqid,
+ desc_ptr, toggle,
+ start_desc, end_desc);
+ case BRCM_MESSAGE_SBA:
+ return flexrm_sba_write_descs(msg, nhcnt, reqid,
+ desc_ptr, toggle,
+ start_desc, end_desc);
+ default:
+ return ERR_PTR(-ENOTSUPP);
+ };
+}
diff --git a/drivers/mailbox/mailbox-flexrm/flexrm-desc.h b/drivers/mailbox/mailbox-flexrm/flexrm-desc.h
new file mode 100644
index 0000000..a95cf61
--- /dev/null
+++ b/drivers/mailbox/mailbox-flexrm/flexrm-desc.h
@@ -0,0 +1,47 @@
+/* Broadcom FlexRM Mailbox Driver
+ *
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * FlexRM descriptor library
+ */
+
+#ifndef __FLEXRM_DESC_H__
+#define __FLEXRM_DESC_H__
+
+#include <linux/types.h>
+#include <linux/device.h>
+#include <linux/mailbox/brcm-message.h>
+
+extern u64 flexrm_read_desc(void *desc_ptr);
+
+extern void flexrm_write_desc(void *desc_ptr, u64 desc);
+
+extern u32 flexrm_cmpl_desc_to_reqid(u64 cmpl_desc);
+
+extern int flexrm_cmpl_desc_to_error(u64 cmpl_desc);
+
+extern bool flexrm_is_next_table_desc(void *desc_ptr);
+
+extern u64 flexrm_next_table_desc(u32 toggle, dma_addr_t next_addr);
+
+extern u64 flexrm_null_desc(u32 toogle);
+
+extern u32 flexrm_estimate_header_desc_count(u32 nhcnt);
+
+extern bool flexrm_sanity_check(struct brcm_message *msg);
+
+extern u32 flexrm_estimate_nonheader_desc_count(struct brcm_message *msg);
+
+extern int flexrm_dma_map(struct device *dev, struct brcm_message *msg);
+
+extern void flexrm_dma_unmap(struct device *dev, struct brcm_message *msg);
+
+extern void *flexrm_write_descs(struct brcm_message *msg, u32 nhcnt,
+ u32 reqid, void *desc_ptr, u32 toggle,
+ void *start_desc, void *end_desc);
+
+#endif /* __FLEXRM_DESC_H__ */
diff --git a/drivers/mailbox/mailbox-flexrm/flexrm-main.c b/drivers/mailbox/mailbox-flexrm/flexrm-main.c
new file mode 100644
index 0000000..c8890f1
--- /dev/null
+++ b/drivers/mailbox/mailbox-flexrm/flexrm-main.c
@@ -0,0 +1,829 @@
+/* Broadcom FlexRM Mailbox Driver
+ *
+ * Copyright (C) 2016 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Each Broadcom FlexSparx4 offload engine is implemented as an
+ * extension to Broadcom FlexRM ring manager. The FlexRM ring
+ * manager provides a set of rings which can be used to submit
+ * work to a FlexSparx4 offload engine.
+ *
+ * This driver creates a mailbox controller using a set of FlexRM
+ * rings where each mailbox channel represents a separate FlexRM ring.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/err.h>
+#include <linux/idr.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/mailbox_client.h>
+#include <linux/mailbox/brcm-message.h>
+#include <linux/module.h>
+#include <linux/msi.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+
+#include "flexrm-desc.h"
+
+/* FlexRM configuration */
+#define RING_REGS_SIZE 0x10000
+#define RING_DESC_SIZE 8
+#define RING_DESC_INDEX(offset) \
+ ((offset) / RING_DESC_SIZE)
+#define RING_DESC_OFFSET(index) \
+ ((index) * RING_DESC_SIZE)
+#define RING_MAX_REQ_COUNT 1024
+#define RING_BD_ALIGN_ORDER 12
+#define RING_BD_ALIGN_CHECK(addr) \
+ (!((addr) & ((0x1 << RING_BD_ALIGN_ORDER) - 1)))
+#define RING_BD_TOGGLE_INVALID(offset) \
+ (((offset) >> RING_BD_ALIGN_ORDER) & 0x1)
+#define RING_BD_TOGGLE_VALID(offset) \
+ (!RING_BD_TOGGLE_INVALID(offset))
+#define RING_BD_DESC_PER_REQ 32
+#define RING_BD_DESC_COUNT \
+ (RING_MAX_REQ_COUNT * RING_BD_DESC_PER_REQ)
+#define RING_BD_SIZE \
+ (RING_BD_DESC_COUNT * RING_DESC_SIZE)
+#define RING_CMPL_ALIGN_ORDER 13
+#define RING_CMPL_DESC_COUNT RING_MAX_REQ_COUNT
+#define RING_CMPL_SIZE \
+ (RING_CMPL_DESC_COUNT * RING_DESC_SIZE)
+#define RING_VER_MAGIC 0x76303031
+
+/* Per-Ring register offsets */
+#define RING_VER 0x000
+#define RING_BD_START_ADDR 0x004
+#define RING_BD_READ_PTR 0x008
+#define RING_BD_WRITE_PTR 0x00c
+#define RING_BD_READ_PTR_DDR_LS 0x010
+#define RING_BD_READ_PTR_DDR_MS 0x014
+#define RING_CMPL_START_ADDR 0x018
+#define RING_CMPL_WRITE_PTR 0x01c
+#define RING_NUM_REQ_RECV_LS 0x020
+#define RING_NUM_REQ_RECV_MS 0x024
+#define RING_NUM_REQ_TRANS_LS 0x028
+#define RING_NUM_REQ_TRANS_MS 0x02c
+#define RING_NUM_REQ_OUTSTAND 0x030
+#define RING_CONTROL 0x034
+#define RING_FLUSH_DONE 0x038
+#define RING_MSI_ADDR_LS 0x03c
+#define RING_MSI_ADDR_MS 0x040
+#define RING_MSI_CONTROL 0x048
+#define RING_BD_READ_PTR_DDR_CONTROL 0x04c
+#define RING_MSI_DATA_VALUE 0x064
+
+/* Register RING_BD_START_ADDR fields */
+#define BD_LAST_UPDATE_HW_SHIFT 28
+#define BD_LAST_UPDATE_HW_MASK 0x1
+#define BD_START_ADDR_VALUE(pa) \
+ ((u32)((((dma_addr_t)(pa)) >> RING_BD_ALIGN_ORDER) & 0x0fffffff))
+#define BD_START_ADDR_DECODE(val) \
+ ((dma_addr_t)((val) & 0x0fffffff) << RING_BD_ALIGN_ORDER)
+
+/* Register RING_CMPL_START_ADDR fields */
+#define CMPL_START_ADDR_VALUE(pa) \
+ ((u32)((((u64)(pa)) >> RING_CMPL_ALIGN_ORDER) & 0x03ffffff))
+
+/* Register RING_CONTROL fields */
+#define CONTROL_MASK_DISABLE_CONTROL 12
+#define CONTROL_FLUSH_SHIFT 5
+#define CONTROL_ACTIVE_SHIFT 4
+#define CONTROL_RATE_ADAPT_MASK 0xf
+#define CONTROL_RATE_DYNAMIC 0x0
+#define CONTROL_RATE_FAST 0x8
+#define CONTROL_RATE_MEDIUM 0x9
+#define CONTROL_RATE_SLOW 0xa
+#define CONTROL_RATE_IDLE 0xb
+
+/* Register RING_FLUSH_DONE fields */
+#define FLUSH_DONE_MASK 0x1
+
+/* Register RING_MSI_CONTROL fields */
+#define MSI_TIMER_VAL_SHIFT 16
+#define MSI_TIMER_VAL_MASK 0xffff
+#define MSI_ENABLE_SHIFT 15
+#define MSI_ENABLE_MASK 0x1
+#define MSI_COUNT_SHIFT 0
+#define MSI_COUNT_MASK 0x3ff
+
+/* Register RING_BD_READ_PTR_DDR_CONTROL fields */
+#define BD_READ_PTR_DDR_TIMER_VAL_SHIFT 16
+#define BD_READ_PTR_DDR_TIMER_VAL_MASK 0xffff
+#define BD_READ_PTR_DDR_ENABLE_SHIFT 15
+#define BD_READ_PTR_DDR_ENABLE_MASK 0x1
+
+struct flexrm_ring {
+ /* Unprotected members */
+ int num;
+ struct flexrm_mbox *mbox;
+ void __iomem *regs;
+ bool irq_requested;
+ unsigned int irq;
+ unsigned int msi_timer_val;
+ unsigned int msi_count_threshold;
+ struct ida requests_ida;
+ struct brcm_message *requests[RING_MAX_REQ_COUNT];
+ void *bd_base;
+ dma_addr_t bd_dma_base;
+ u32 bd_write_offset;
+ void *cmpl_base;
+ dma_addr_t cmpl_dma_base;
+ /* Protected members */
+ spinlock_t lock;
+ struct brcm_message *last_pending_msg;
+ u32 cmpl_read_offset;
+};
+
+struct flexrm_mbox {
+ struct device *dev;
+ void __iomem *regs;
+ u32 num_rings;
+ struct flexrm_ring *rings;
+ u64 dma_mask;
+ struct dma_pool *bd_pool;
+ struct dma_pool *cmpl_pool;
+ struct mbox_controller controller;
+};
+
+static int flexrm_new_request(struct flexrm_ring *ring,
+ struct brcm_message *batch_msg,
+ struct brcm_message *msg)
+{
+ void *next;
+ unsigned long flags;
+ u32 val, count, nhcnt;
+ u32 read_offset, write_offset;
+ bool exit_cleanup = false;
+ int ret = 0, reqid;
+
+ /* Do sanity check on message */
+ if (!flexrm_sanity_check(msg))
+ return -EIO;
+ msg->error = 0;
+
+ /* If no requests possible then save data pointer and goto done. */
+ reqid = ida_simple_get(&ring->requests_ida, 0,
+ RING_MAX_REQ_COUNT, GFP_KERNEL);
+ if (reqid < 0) {
+ spin_lock_irqsave(&ring->lock, flags);
+ if (batch_msg)
+ ring->last_pending_msg = batch_msg;
+ else
+ ring->last_pending_msg = msg;
+ spin_unlock_irqrestore(&ring->lock, flags);
+ return 0;
+ }
+ ring->requests[reqid] = msg;
+
+ /* Do DMA mappings for the message */
+ ret = flexrm_dma_map(ring->mbox->dev, msg);
+ if (ret < 0) {
+ ring->requests[reqid] = NULL;
+ ida_simple_remove(&ring->requests_ida, reqid);
+ return ret;
+ }
+
+ /* If last_pending_msg is already set then goto done with error */
+ spin_lock_irqsave(&ring->lock, flags);
+ if (ring->last_pending_msg)
+ ret = -ENOSPC;
+ spin_unlock_irqrestore(&ring->lock, flags);
+ if (ret < 0) {
+ dev_warn(ring->mbox->dev, "no space in ring %d\n", ring->num);
+ exit_cleanup = true;
+ goto exit;
+ }
+
+ /* Determine current HW BD read offset */
+ read_offset = readl_relaxed(ring->regs + RING_BD_READ_PTR);
+ val = readl_relaxed(ring->regs + RING_BD_START_ADDR);
+ read_offset *= RING_DESC_SIZE;
+ read_offset += (u32)(BD_START_ADDR_DECODE(val) - ring->bd_dma_base);
+
+ /*
+ * Number required descriptors = number of non-header descriptors +
+ * number of header descriptors +
+ * 1x null descriptor
+ */
+ nhcnt = flexrm_estimate_nonheader_desc_count(msg);
+ count = flexrm_estimate_header_desc_count(nhcnt) + nhcnt + 1;
+
+ /* Check for available descriptor space. */
+ write_offset = ring->bd_write_offset;
+ while (count) {
+ if (!flexrm_is_next_table_desc(ring->bd_base + write_offset))
+ count--;
+ write_offset += RING_DESC_SIZE;
+ if (write_offset == RING_BD_SIZE)
+ write_offset = 0x0;
+ if (write_offset == read_offset)
+ break;
+ }
+ if (count) {
+ spin_lock_irqsave(&ring->lock, flags);
+ if (batch_msg)
+ ring->last_pending_msg = batch_msg;
+ else
+ ring->last_pending_msg = msg;
+ spin_unlock_irqrestore(&ring->lock, flags);
+ ret = 0;
+ exit_cleanup = true;
+ goto exit;
+ }
+
+ /* Write descriptors to ring */
+ next = flexrm_write_descs(msg, nhcnt, reqid,
+ ring->bd_base + ring->bd_write_offset,
+ RING_BD_TOGGLE_VALID(ring->bd_write_offset),
+ ring->bd_base, ring->bd_base + RING_BD_SIZE);
+ if (IS_ERR(next)) {
+ ret = PTR_ERR(next);
+ exit_cleanup = true;
+ goto exit;
+ }
+
+ /* Save ring BD write offset */
+ ring->bd_write_offset = (unsigned long)(next - ring->bd_base);
+
+exit:
+ /* Update error status in message */
+ msg->error = ret;
+
+ /* Cleanup if we failed */
+ if (exit_cleanup) {
+ flexrm_dma_unmap(ring->mbox->dev, msg);
+ ring->requests[reqid] = NULL;
+ ida_simple_remove(&ring->requests_ida, reqid);
+ }
+
+ return ret;
+}
+
+static int flexrm_process_completions(struct flexrm_ring *ring)
+{
+ u64 desc;
+ int err, count = 0;
+ unsigned long flags;
+ struct brcm_message *msg = NULL;
+ u32 reqid, cmpl_read_offset, cmpl_write_offset;
+ struct mbox_chan *chan = &ring->mbox->controller.chans[ring->num];
+
+ spin_lock_irqsave(&ring->lock, flags);
+
+ /* Check last_pending_msg */
+ if (ring->last_pending_msg) {
+ msg = ring->last_pending_msg;
+ ring->last_pending_msg = NULL;
+ }
+
+ /*
+ * Get current completion read and write offset
+ *
+ * Note: We should read completion write pointer atleast once
+ * after we get a MSI interrupt because HW maintains internal
+ * MSI status which will allow next MSI interrupt only after
+ * completion write pointer is read.
+ */
+ cmpl_write_offset = readl_relaxed(ring->regs + RING_CMPL_WRITE_PTR);
+ cmpl_write_offset *= RING_DESC_SIZE;
+ cmpl_read_offset = ring->cmpl_read_offset;
+ ring->cmpl_read_offset = cmpl_write_offset;
+
+ spin_unlock_irqrestore(&ring->lock, flags);
+
+ /* If last_pending_msg was set then queue it back */
+ if (msg)
+ mbox_send_message(chan, msg);
+
+ /* For each completed request notify mailbox clients */
+ reqid = 0;
+ while (cmpl_read_offset != cmpl_write_offset) {
+ /* Dequeue next completion descriptor */
+ desc = *((u64 *)(ring->cmpl_base + cmpl_read_offset));
+
+ /* Next read offset */
+ cmpl_read_offset += RING_DESC_SIZE;
+ if (cmpl_read_offset == RING_CMPL_SIZE)
+ cmpl_read_offset = 0;
+
+ /* Decode error from completion descriptor */
+ err = flexrm_cmpl_desc_to_error(desc);
+ if (err < 0) {
+ dev_warn(ring->mbox->dev,
+ "got completion desc=0x%lx with error %d",
+ (unsigned long)desc, err);
+ }
+
+ /* Determine request id from completion descriptor */
+ reqid = flexrm_cmpl_desc_to_reqid(desc);
+
+ /* Determine message pointer based on reqid */
+ msg = ring->requests[reqid];
+ if (!msg) {
+ dev_warn(ring->mbox->dev,
+ "null msg pointer for completion desc=0x%lx",
+ (unsigned long)desc);
+ continue;
+ }
+
+ /* Release reqid for recycling */
+ ring->requests[reqid] = NULL;
+ ida_simple_remove(&ring->requests_ida, reqid);
+
+ /* Unmap DMA mappings */
+ flexrm_dma_unmap(ring->mbox->dev, msg);
+
+ /* Give-back message to mailbox client */
+ msg->error = err;
+ mbox_chan_received_data(chan, msg);
+
+ /* Increment number of completions processed */
+ count++;
+ }
+
+ return count;
+}
+
+static irqreturn_t flexrm_irq_event(int irq, void *dev_id)
+{
+ /* We only have MSI for completions so just wakeup IRQ thread */
+ /* Ring related errors will be informed via completion descriptors */
+
+ return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t flexrm_irq_thread(int irq, void *dev_id)
+{
+ flexrm_process_completions(dev_id);
+
+ return IRQ_HANDLED;
+}
+
+static int flexrm_send_data(struct mbox_chan *chan, void *data)
+{
+ int i, rc;
+ struct flexrm_ring *ring = chan->con_priv;
+ struct brcm_message *msg = data;
+
+ if (msg->type == BRCM_MESSAGE_BATCH) {
+ for (i = msg->batch.msgs_queued;
+ i < msg->batch.msgs_count; i++) {
+ rc = flexrm_new_request(ring, msg,
+ &msg->batch.msgs[i]);
+ if (rc) {
+ msg->error = rc;
+ return rc;
+ }
+ msg->batch.msgs_queued++;
+ }
+ return 0;
+ }
+
+ return flexrm_new_request(ring, NULL, data);
+}
+
+static bool flexrm_peek_data(struct mbox_chan *chan)
+{
+ int cnt = flexrm_process_completions(chan->con_priv);
+
+ return (cnt > 0) ? true : false;
+}
+
+static int flexrm_startup(struct mbox_chan *chan)
+{
+ u64 d;
+ u32 val, off;
+ int ret = 0;
+ dma_addr_t next_addr;
+ struct flexrm_ring *ring = chan->con_priv;
+
+ /* Allocate BD memory */
+ ring->bd_base = dma_pool_alloc(ring->mbox->bd_pool,
+ GFP_KERNEL, &ring->bd_dma_base);
+ if (!ring->bd_base) {
+ dev_err(ring->mbox->dev, "can't allocate BD memory\n");
+ ret = -ENOMEM;
+ goto fail;
+ }
+
+ /* Configure next table pointer entries in BD memory */
+ for (off = 0; off < RING_BD_SIZE; off += RING_DESC_SIZE) {
+ next_addr = off + RING_DESC_SIZE;
+ if (next_addr == RING_BD_SIZE)
+ next_addr = 0;
+ next_addr += ring->bd_dma_base;
+ if (RING_BD_ALIGN_CHECK(next_addr))
+ d = flexrm_next_table_desc(RING_BD_TOGGLE_VALID(off),
+ next_addr);
+ else
+ d = flexrm_null_desc(RING_BD_TOGGLE_INVALID(off));
+ flexrm_write_desc(ring->bd_base + off, d);
+ }
+
+ /* Allocate completion memory */
+ ring->cmpl_base = dma_pool_alloc(ring->mbox->cmpl_pool,
+ GFP_KERNEL, &ring->cmpl_dma_base);
+ if (!ring->cmpl_base) {
+ dev_err(ring->mbox->dev, "can't allocate completion memory\n");
+ ret = -ENOMEM;
+ goto fail_free_bd_memory;
+ }
+ memset(ring->cmpl_base, 0, RING_CMPL_SIZE);
+
+ /* Request IRQ */
+ if (ring->irq == UINT_MAX) {
+ dev_err(ring->mbox->dev, "ring IRQ not available\n");
+ ret = -ENODEV;
+ goto fail_free_cmpl_memory;
+ }
+ ret = request_threaded_irq(ring->irq,
+ flexrm_irq_event,
+ flexrm_irq_thread,
+ 0, dev_name(ring->mbox->dev), ring);
+ if (ret) {
+ dev_err(ring->mbox->dev, "failed to request ring IRQ\n");
+ goto fail_free_cmpl_memory;
+ }
+ ring->irq_requested = true;
+
+ /* Disable/inactivate ring */
+ writel_relaxed(0x0, ring->regs + RING_CONTROL);
+
+ /* Program BD start address */
+ val = BD_START_ADDR_VALUE(ring->bd_dma_base);
+ writel_relaxed(val, ring->regs + RING_BD_START_ADDR);
+
+ /* BD write pointer will be same as HW write pointer */
+ ring->bd_write_offset =
+ readl_relaxed(ring->regs + RING_BD_WRITE_PTR);
+ ring->bd_write_offset *= RING_DESC_SIZE;
+
+ /* Program completion start address */
+ val = CMPL_START_ADDR_VALUE(ring->cmpl_dma_base);
+ writel_relaxed(val, ring->regs + RING_CMPL_START_ADDR);
+
+ /* Ensure last pending message is cleared */
+ ring->last_pending_msg = NULL;
+
+ /* Completion read pointer will be same as HW write pointer */
+ ring->cmpl_read_offset =
+ readl_relaxed(ring->regs + RING_CMPL_WRITE_PTR);
+ ring->cmpl_read_offset *= RING_DESC_SIZE;
+
+ /* Read ring Tx, Rx, and Outstanding counts to clear */
+ readl_relaxed(ring->regs + RING_NUM_REQ_RECV_LS);
+ readl_relaxed(ring->regs + RING_NUM_REQ_RECV_MS);
+ readl_relaxed(ring->regs + RING_NUM_REQ_TRANS_LS);
+ readl_relaxed(ring->regs + RING_NUM_REQ_TRANS_MS);
+ readl_relaxed(ring->regs + RING_NUM_REQ_OUTSTAND);
+
+ /* Configure RING_MSI_CONTROL */
+ val = 0;
+ val |= (ring->msi_timer_val << MSI_TIMER_VAL_SHIFT);
+ val |= BIT(MSI_ENABLE_SHIFT);
+ val |= (ring->msi_count_threshold & MSI_COUNT_MASK) << MSI_COUNT_SHIFT;
+ writel_relaxed(val, ring->regs + RING_MSI_CONTROL);
+
+ /* Enable/activate ring */
+ val = BIT(CONTROL_ACTIVE_SHIFT);
+ writel_relaxed(val, ring->regs + RING_CONTROL);
+
+ return 0;
+
+fail_free_cmpl_memory:
+ dma_pool_free(ring->mbox->cmpl_pool,
+ ring->cmpl_base, ring->cmpl_dma_base);
+ ring->cmpl_base = NULL;
+fail_free_bd_memory:
+ dma_pool_free(ring->mbox->bd_pool,
+ ring->bd_base, ring->bd_dma_base);
+ ring->bd_base = NULL;
+fail:
+ return ret;
+}
+
+static void flexrm_shutdown(struct mbox_chan *chan)
+{
+ u32 reqid;
+ unsigned int timeout;
+ struct brcm_message *msg;
+ struct flexrm_ring *ring = chan->con_priv;
+
+ /* Disable/inactivate ring */
+ writel_relaxed(0x0, ring->regs + RING_CONTROL);
+
+ /* Flush ring with timeout of 1s */
+ timeout = 1000;
+ writel_relaxed(BIT(CONTROL_FLUSH_SHIFT),
+ ring->regs + RING_CONTROL);
+ do {
+ if (readl_relaxed(ring->regs + RING_FLUSH_DONE) &
+ FLUSH_DONE_MASK)
+ break;
+ mdelay(1);
+ } while (timeout--);
+
+ /* Abort all in-flight requests */
+ for (reqid = 0; reqid < RING_MAX_REQ_COUNT; reqid++) {
+ msg = ring->requests[reqid];
+ if (!msg)
+ continue;
+
+ /* Release reqid for recycling */
+ ring->requests[reqid] = NULL;
+ ida_simple_remove(&ring->requests_ida, reqid);
+
+ /* Unmap DMA mappings */
+ flexrm_dma_unmap(ring->mbox->dev, msg);
+
+ /* Give-back message to mailbox client */
+ msg->error = -EIO;
+ mbox_chan_received_data(chan, msg);
+ }
+
+ /* Release IRQ */
+ if (ring->irq_requested) {
+ free_irq(ring->irq, ring);
+ ring->irq_requested = false;
+ }
+
+ /* Free-up completion descriptor ring */
+ if (ring->cmpl_base) {
+ dma_pool_free(ring->mbox->cmpl_pool,
+ ring->cmpl_base, ring->cmpl_dma_base);
+ ring->cmpl_base = NULL;
+ }
+
+ /* Free-up BD descriptor ring */
+ if (ring->bd_base) {
+ dma_pool_free(ring->mbox->bd_pool,
+ ring->bd_base, ring->bd_dma_base);
+ ring->bd_base = NULL;
+ }
+}
+
+static bool flexrm_last_tx_done(struct mbox_chan *chan)
+{
+ bool ret;
+ unsigned long flags;
+ struct flexrm_ring *ring = chan->con_priv;
+
+ spin_lock_irqsave(&ring->lock, flags);
+ ret = (ring->last_pending_msg) ? false : true;
+ spin_unlock_irqrestore(&ring->lock, flags);
+
+ return ret;
+}
+
+static const struct mbox_chan_ops flexrm_mbox_chan_ops = {
+ .send_data = flexrm_send_data,
+ .startup = flexrm_startup,
+ .shutdown = flexrm_shutdown,
+ .last_tx_done = flexrm_last_tx_done,
+ .peek_data = flexrm_peek_data,
+};
+
+static void flexrm_mbox_msi_write(struct msi_desc *desc, struct msi_msg *msg)
+{
+ struct device *dev = msi_desc_to_dev(desc);
+ struct flexrm_mbox *mbox = dev_get_drvdata(dev);
+ struct flexrm_ring *ring = &mbox->rings[desc->platform.msi_index];
+
+ /* Configure per-Ring MSI registers */
+ writel_relaxed(msg->address_lo, ring->regs + RING_MSI_ADDR_LS);
+ writel_relaxed(msg->address_hi, ring->regs + RING_MSI_ADDR_MS);
+ writel_relaxed(msg->data, ring->regs + RING_MSI_DATA_VALUE);
+}
+
+static struct mbox_chan *flexrm_mbox_of_xlate(struct mbox_controller *cntlr,
+ const struct of_phandle_args *pa)
+{
+ struct mbox_chan *chan;
+ struct flexrm_ring *ring;
+
+ if (pa->args_count < 3)
+ return ERR_PTR(-EINVAL);
+
+ if (pa->args[0] >= cntlr->num_chans)
+ return ERR_PTR(-ENOENT);
+
+ if (pa->args[1] > MSI_COUNT_MASK)
+ return ERR_PTR(-EINVAL);
+
+ if (pa->args[2] > MSI_TIMER_VAL_MASK)
+ return ERR_PTR(-EINVAL);
+
+ chan = &cntlr->chans[pa->args[0]];
+ ring = chan->con_priv;
+ ring->msi_count_threshold = pa->args[1];
+ ring->msi_timer_val = pa->args[2];
+
+ return chan;
+}
+
+static int flexrm_mbox_probe(struct platform_device *pdev)
+{
+ int index, ret = 0;
+ void __iomem *regs;
+ void __iomem *regs_end;
+ struct msi_desc *desc;
+ struct resource *iomem;
+ struct flexrm_ring *ring;
+ struct flexrm_mbox *mbox;
+ struct device *dev = &pdev->dev;
+
+ /* Allocate driver mailbox struct */
+ mbox = devm_kzalloc(dev, sizeof(*mbox), GFP_KERNEL);
+ if (!mbox) {
+ ret = -ENOMEM;
+ goto fail;
+ }
+ mbox->dev = dev;
+ platform_set_drvdata(pdev, mbox);
+
+ /* Get resource for registers */
+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!iomem || (resource_size(iomem) < RING_REGS_SIZE)) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ /* Map registers of all rings */
+ mbox->regs = devm_ioremap_resource(&pdev->dev, iomem);
+ if (IS_ERR(mbox->regs)) {
+ ret = PTR_ERR(mbox->regs);
+ dev_err(&pdev->dev, "Failed to remap mailbox regs: %d\n", ret);
+ goto fail;
+ }
+ regs_end = mbox->regs + resource_size(iomem);
+
+ /* Scan and count available rings */
+ mbox->num_rings = 0;
+ for (regs = mbox->regs; regs < regs_end; regs += RING_REGS_SIZE) {
+ if (readl_relaxed(regs + RING_VER) == RING_VER_MAGIC)
+ mbox->num_rings++;
+ }
+ if (!mbox->num_rings) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ /* Allocate driver ring structs */
+ ring = devm_kcalloc(dev, mbox->num_rings, sizeof(*ring), GFP_KERNEL);
+ if (!ring) {
+ ret = -ENOMEM;
+ goto fail;
+ }
+ mbox->rings = ring;
+
+ /* Initialize members of driver ring structs */
+ regs = mbox->regs;
+ for (index = 0; index < mbox->num_rings; index++) {
+ ring = &mbox->rings[index];
+ ring->num = index;
+ ring->mbox = mbox;
+ while ((regs < regs_end) &&
+ (readl_relaxed(regs + RING_VER) != RING_VER_MAGIC))
+ regs += RING_REGS_SIZE;
+ if (regs_end <= regs) {
+ ret = -ENODEV;
+ goto fail;
+ }
+ ring->regs = regs;
+ regs += RING_REGS_SIZE;
+ ring->irq = UINT_MAX;
+ ring->irq_requested = false;
+ ring->msi_timer_val = MSI_TIMER_VAL_MASK;
+ ring->msi_count_threshold = 0x1;
+ ida_init(&ring->requests_ida);
+ memset(ring->requests, 0, sizeof(ring->requests));
+ ring->bd_base = NULL;
+ ring->bd_dma_base = 0;
+ ring->cmpl_base = NULL;
+ ring->cmpl_dma_base = 0;
+ spin_lock_init(&ring->lock);
+ ring->last_pending_msg = NULL;
+ ring->cmpl_read_offset = 0;
+ }
+
+ /* FlexRM is capable of 40-bit physical addresses only */
+ mbox->dma_mask = DMA_BIT_MASK(40);
+ dev->dma_mask = &mbox->dma_mask;
+
+ /* Create DMA pool for ring BD memory */
+ mbox->bd_pool = dma_pool_create("bd", dev, RING_BD_SIZE,
+ 1 << RING_BD_ALIGN_ORDER, 0);
+ if (!mbox->bd_pool) {
+ ret = -ENOMEM;
+ goto fail;
+ }
+
+ /* Create DMA pool for ring completion memory */
+ mbox->cmpl_pool = dma_pool_create("cmpl", dev, RING_CMPL_SIZE,
+ 1 << RING_CMPL_ALIGN_ORDER, 0);
+ if (!mbox->cmpl_pool) {
+ ret = -ENOMEM;
+ goto fail_destroy_bd_pool;
+ }
+
+ /* Allocate platform MSIs for each ring */
+ ret = platform_msi_domain_alloc_irqs(dev, mbox->num_rings,
+ flexrm_mbox_msi_write);
+ if (ret)
+ goto fail_destroy_cmpl_pool;
+
+ /* Save alloced IRQ numbers for each ring */
+ for_each_msi_entry(desc, dev) {
+ ring = &mbox->rings[desc->platform.msi_index];
+ ring->irq = desc->irq;
+ }
+
+ /* Initialize mailbox controller */
+ mbox->controller.txdone_irq = false;
+ mbox->controller.txdone_poll = true;
+ mbox->controller.txpoll_period = 1;
+ mbox->controller.ops = &flexrm_mbox_chan_ops;
+ mbox->controller.dev = dev;
+ mbox->controller.num_chans = mbox->num_rings;
+ mbox->controller.of_xlate = flexrm_mbox_of_xlate;
+ mbox->controller.chans = devm_kcalloc(dev, mbox->num_rings,
+ sizeof(*mbox->controller.chans), GFP_KERNEL);
+ if (!mbox->controller.chans) {
+ ret = -ENOMEM;
+ goto fail_free_msis;
+ }
+ for (index = 0; index < mbox->num_rings; index++)
+ mbox->controller.chans[index].con_priv = &mbox->rings[index];
+
+ /* Register mailbox controller */
+ ret = mbox_controller_register(&mbox->controller);
+ if (ret)
+ goto fail_free_msis;
+
+ dev_info(dev, "registered flexrm mailbox with %d channels\n",
+ mbox->controller.num_chans);
+
+ return 0;
+
+fail_free_msis:
+ platform_msi_domain_free_irqs(dev);
+fail_destroy_cmpl_pool:
+ dma_pool_destroy(mbox->cmpl_pool);
+fail_destroy_bd_pool:
+ dma_pool_destroy(mbox->bd_pool);
+fail:
+ return ret;
+}
+
+static int flexrm_mbox_remove(struct platform_device *pdev)
+{
+ int index;
+ struct device *dev = &pdev->dev;
+ struct flexrm_ring *ring;
+ struct flexrm_mbox *mbox = platform_get_drvdata(pdev);
+
+ mbox_controller_unregister(&mbox->controller);
+
+ platform_msi_domain_free_irqs(dev);
+
+ dma_pool_destroy(mbox->cmpl_pool);
+ dma_pool_destroy(mbox->bd_pool);
+
+ for (index = 0; index < mbox->num_rings; index++) {
+ ring = &mbox->rings[index];
+ ida_destroy(&ring->requests_ida);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id flexrm_mbox_of_match[] = {
+ { .compatible = "brcm,iproc-flexrm-mbox", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, flexrm_mbox_of_match);
+
+static struct platform_driver flexrm_mbox_driver = {
+ .driver = {
+ .name = "brcm-flexrm-mbox",
+ .of_match_table = flexrm_mbox_of_match,
+ },
+ .probe = flexrm_mbox_probe,
+ .remove = flexrm_mbox_remove,
+};
+module_platform_driver(flexrm_mbox_driver);
+
+MODULE_AUTHOR("Anup Patel <anup.patel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>");
+MODULE_DESCRIPTION("Broadcom FlexRM mailbox driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mailbox/brcm-message.h b/include/linux/mailbox/brcm-message.h
index 6b55c93..c20b484 100644
--- a/include/linux/mailbox/brcm-message.h
+++ b/include/linux/mailbox/brcm-message.h
@@ -16,6 +16,7 @@
enum brcm_message_type {
BRCM_MESSAGE_UNKNOWN = 0,
+ BRCM_MESSAGE_BATCH,
BRCM_MESSAGE_SPU,
BRCM_MESSAGE_SBA,
BRCM_MESSAGE_MAX,
@@ -23,24 +24,29 @@ enum brcm_message_type {
struct brcm_sba_command {
u64 cmd;
+ u64 *cmd_dma;
+ dma_addr_t cmd_dma_addr;
#define BRCM_SBA_CMD_TYPE_A BIT(0)
#define BRCM_SBA_CMD_TYPE_B BIT(1)
#define BRCM_SBA_CMD_TYPE_C BIT(2)
#define BRCM_SBA_CMD_HAS_RESP BIT(3)
#define BRCM_SBA_CMD_HAS_OUTPUT BIT(4)
u64 flags;
- dma_addr_t input;
- size_t input_len;
dma_addr_t resp;
size_t resp_len;
- dma_addr_t output;
- size_t output_len;
+ dma_addr_t data;
+ size_t data_len;
};
struct brcm_message {
enum brcm_message_type type;
union {
struct {
+ struct brcm_message *msgs;
+ unsigned int msgs_queued;
+ unsigned int msgs_count;
+ } batch;
+ struct {
struct scatterlist *src;
struct scatterlist *dst;
} spu;
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v3 2/2] dt-bindings: Add DT bindings info for FlexRM ring manager
From: Anup Patel @ 2017-01-04 5:34 UTC (permalink / raw)
To: Jassi Brar, Rob Herring
Cc: Mark Rutland, Ray Jui, Scott Branden, Pramod KUMAR, Rob Rice,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w, Anup Patel
In-Reply-To: <1483508082-7008-1-git-send-email-anup.patel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
This patch adds device tree bindings document for the FlexRM
ring manager found on Broadcom iProc SoCs.
Reviewed-by: Ray Jui <ray.jui-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Reviewed-by: Scott Branden <scott.branden-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
Signed-off-by: Anup Patel <anup.patel-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
.../bindings/mailbox/brcm,iproc-flexrm-mbox.txt | 60 ++++++++++++++++++++++
1 file changed, 60 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt
diff --git a/Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt
new file mode 100644
index 0000000..ca51a39
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/brcm,iproc-flexrm-mbox.txt
@@ -0,0 +1,60 @@
+Broadcom FlexRM Ring Manager
+============================
+The Broadcom FlexRM ring manager provides a set of rings which can be
+used to submit work to offload engines. An SoC may have multiple FlexRM
+hardware blocks. There is one device tree entry per FlexRM block. The
+FlexRM driver will create a mailbox-controller instance for given FlexRM
+hardware block where each mailbox channel is a separate FlexRM ring.
+
+Required properties:
+--------------------
+- compatible: Should be "brcm,iproc-flexrm-mbox"
+- reg: Specifies base physical address and size of the FlexRM
+ ring registers
+- msi-parent: Phandles (and potential Device IDs) to MSI controllers
+ The FlexRM engine will send MSIs (instead of wired
+ interrupts) to CPU. There is one MSI for each FlexRM ring.
+ Refer devicetree/bindings/interrupt-controller/msi.txt
+- #mbox-cells: Specifies the number of cells needed to encode a mailbox
+ channel. This should be 3.
+
+ The 1st cell is the mailbox channel number.
+
+ The 2nd cell contains MSI completion threshold. This is the
+ number of completion messages for which FlexRM will inject
+ one MSI interrupt to CPU.
+
+ The 3nd cell contains MSI timer value representing time for
+ which FlexRM will wait to accumulate N completion messages
+ where N is the value specified by 2nd cell above. If FlexRM
+ does not get required number of completion messages in time
+ specified by this cell then it will inject one MSI interrupt
+ to CPU provided atleast one completion message is available.
+
+Optional properties:
+--------------------
+- dma-coherent: Present if DMA operations made by the FlexRM engine (such
+ as DMA descriptor access, access to buffers pointed by DMA
+ descriptors and read/write pointer updates to DDR) are
+ cache coherent with the CPU.
+
+Example:
+--------
+crypto_mbox: mbox@67000000 {
+ compatible = "brcm,iproc-flexrm-mbox";
+ reg = <0x67000000 0x200000>;
+ msi-parent = <&gic_its 0x7f00>;
+ #mbox-cells = <3>;
+};
+
+crypto_client {
+ ...
+ mboxes = <&crypto_mbox 0 0x1 0xffff>,
+ <&crypto_mbox 1 0x1 0xffff>,
+ <&crypto_mbox 16 0x1 0xffff>,
+ <&crypto_mbox 17 0x1 0xffff>,
+ <&crypto_mbox 30 0x1 0xffff>,
+ <&crypto_mbox 31 0x1 0xffff>;
+ };
+ ...
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH v5 2/4] soc: zte: pm_domains: Prepare for supporting ARMv8 zx2967 family
From: Shawn Guo @ 2017-01-04 5:44 UTC (permalink / raw)
To: Baoyou Xie
Cc: jun.nie-QSEj5FYQhm4dnm+yROfE0A, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
davem-fT/PcQaiUtIeIZ0/mPfg9Q,
geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ,
akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, linux-0h96xk9xTtrk1uMJSBkQmQ,
krzk-DgEjT+Ai2ygdnm+yROfE0A, arnd-r2nGTMty4D4,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A,
pankaj.dubey-Sze3O3UU22JBDgjK7y7TUQ, yangbo.lu-3arQi8VN3Tc,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, claudiu.manoil-3arQi8VN3Tc,
laurent.pinchart+renesas-ryLnwIuWjnjg/C1BVhZhaw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
In-Reply-To: <1483489157-10782-2-git-send-email-baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
On Wed, Jan 04, 2017 at 08:19:15AM +0800, Baoyou Xie wrote:
> The ARMv8 zx2967 family (296718, 296716 etc) uses different value
> for controlling the power domain on/off registers, Choose the
> value depending on the compatible.
>
> Multiple domains are prepared for the family, this patch prepares
> the common functions.
>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Reviewed-by: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Reviewed-by: Jun Nie <jun.nie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Same here. Neither myself nor Jun gave Reviewed-by tag on this patch.
> ---
> drivers/soc/Kconfig | 1 +
> drivers/soc/Makefile | 1 +
> drivers/soc/zte/Kconfig | 13 ++++
> drivers/soc/zte/Makefile | 4 ++
> drivers/soc/zte/zx2967_pm_domains.c | 139 ++++++++++++++++++++++++++++++++++++
> drivers/soc/zte/zx2967_pm_domains.h | 46 ++++++++++++
> 6 files changed, 204 insertions(+)
> create mode 100644 drivers/soc/zte/Kconfig
> create mode 100644 drivers/soc/zte/Makefile
> create mode 100644 drivers/soc/zte/zx2967_pm_domains.c
> create mode 100644 drivers/soc/zte/zx2967_pm_domains.h
>
> diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig
> index f31bceb..f09023f 100644
> --- a/drivers/soc/Kconfig
> +++ b/drivers/soc/Kconfig
> @@ -11,5 +11,6 @@ source "drivers/soc/tegra/Kconfig"
> source "drivers/soc/ti/Kconfig"
> source "drivers/soc/ux500/Kconfig"
> source "drivers/soc/versatile/Kconfig"
> +source "drivers/soc/zte/Kconfig"
>
> endmenu
> diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
> index 50c23d0..05eae52 100644
> --- a/drivers/soc/Makefile
> +++ b/drivers/soc/Makefile
> @@ -16,3 +16,4 @@ obj-$(CONFIG_ARCH_TEGRA) += tegra/
> obj-$(CONFIG_SOC_TI) += ti/
> obj-$(CONFIG_ARCH_U8500) += ux500/
> obj-$(CONFIG_PLAT_VERSATILE) += versatile/
> +obj-$(CONFIG_ARCH_ZX) += zte/
> diff --git a/drivers/soc/zte/Kconfig b/drivers/soc/zte/Kconfig
> new file mode 100644
> index 0000000..20bde38
> --- /dev/null
> +++ b/drivers/soc/zte/Kconfig
> @@ -0,0 +1,13 @@
> +#
> +# ZTE SoC drivers
> +#
> +menuconfig SOC_ZTE
> + bool "ZTE SoC driver support"
> +
> +if SOC_ZTE
> +
> +config ZX2967_PM_DOMAINS
> + bool "ZX2967 PM domains"
> + depends on PM_GENERIC_DOMAINS
> +
> +endif
> diff --git a/drivers/soc/zte/Makefile b/drivers/soc/zte/Makefile
> new file mode 100644
> index 0000000..8a37f2f
> --- /dev/null
> +++ b/drivers/soc/zte/Makefile
> @@ -0,0 +1,4 @@
> +#
> +# ZTE SOC drivers
> +#
> +obj-$(CONFIG_ZX2967_PM_DOMAINS) += zx2967_pm_domains.o
> diff --git a/drivers/soc/zte/zx2967_pm_domains.c b/drivers/soc/zte/zx2967_pm_domains.c
> new file mode 100644
> index 0000000..a215875
> --- /dev/null
> +++ b/drivers/soc/zte/zx2967_pm_domains.c
> @@ -0,0 +1,139 @@
> +/*
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/of.h>
> +
> +#include "zx2967_pm_domains.h"
> +
> +#define PCU_DM_CLKEN(zpd) ((zpd)->reg_offset[REG_CLKEN])
> +#define PCU_DM_ISOEN(zpd) ((zpd)->reg_offset[REG_ISOEN])
> +#define PCU_DM_RSTEN(zpd) ((zpd)->reg_offset[REG_RSTEN])
> +#define PCU_DM_PWREN(zpd) ((zpd)->reg_offset[REG_PWREN])
> +#define PCU_DM_PWRDN(zpd) ((zpd)->reg_offset[REG_PWRDN])
PCU_DM_PWRDN doesn't seem to be used anywhere in this driver.
> +#define PCU_DM_ACK_SYNC(zpd) ((zpd)->reg_offset[REG_ACK_SYNC])
> +
> +static void __iomem *pcubase;
> +
> +int zx2967_power_on(struct generic_pm_domain *domain)
> +{
> + struct zx2967_pm_domain *zpd = (struct zx2967_pm_domain *)domain;
> + unsigned long loop = 1000;
> + u32 val;
> +
> + val = readl_relaxed(pcubase + PCU_DM_PWREN(zpd));
> + if (zpd->polarity == PWREN)
> + val |= BIT(zpd->bit);
> + else
> + val &= ~BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_PWREN(zpd));
> +
> + do {
> + udelay(1);
> + val = readl_relaxed(pcubase + PCU_DM_ACK_SYNC(zpd))
> + & BIT(zpd->bit);
> + } while (--loop && !val);
> +
> + if (!loop) {
> + pr_err("Error: %s %s fail\n", __func__, domain->name);
> + return -EIO;
> + }
> +
> + val = readl_relaxed(pcubase + PCU_DM_RSTEN(zpd));
> + val |= BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_RSTEN(zpd));
> + udelay(5);
> +
> + val = readl_relaxed(pcubase + PCU_DM_ISOEN(zpd));
> + val &= ~BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_ISOEN(zpd));
> + udelay(5);
> +
> + val = readl_relaxed(pcubase + PCU_DM_CLKEN(zpd));
> + val |= BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_CLKEN(zpd));
> + udelay(5);
> +
> + pr_debug("normal poweron %s\n", domain->name);
Does "normal" in the debug message mean anything here?
> +
> + return 0;
> +}
> +
> +int zx2967_power_off(struct generic_pm_domain *domain)
> +{
> + struct zx2967_pm_domain *zpd = (struct zx2967_pm_domain *)domain;
> + unsigned long loop = 1000;
> + u32 val;
> +
> + val = readl_relaxed(pcubase + PCU_DM_CLKEN(zpd));
> + val &= ~BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_CLKEN(zpd));
> + udelay(5);
> +
> + val = readl_relaxed(pcubase + PCU_DM_ISOEN(zpd));
> + val |= BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_ISOEN(zpd));
> + udelay(5);
> +
> + val = readl_relaxed(pcubase + PCU_DM_RSTEN(zpd));
> + val &= ~BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_RSTEN(zpd));
> + udelay(5);
> +
> + val = readl_relaxed(pcubase + PCU_DM_PWREN(zpd));
> + if (zpd->polarity == PWREN)
> + val &= ~BIT(zpd->bit);
> + else
> + val |= BIT(zpd->bit);
> + writel_relaxed(val, pcubase + PCU_DM_PWREN(zpd));
> +
> + do {
> + udelay(1);
> + val = readl_relaxed(pcubase + PCU_DM_ACK_SYNC(zpd))
> + & BIT(zpd->bit);
> + } while (--loop && val);
> +
> + if (!loop) {
> + pr_err("Error: %s %s fail\n", __func__, domain->name);
> + return -EIO;
> + }
> +
> + pr_debug("normal poweroff %s\n", domain->name);
Ditto
> +
> + return 0;
> +}
> +
> +int zx2967_pd_probe(struct platform_device *pdev,
> + struct generic_pm_domain **zx_pm_domains,
> + int domain_num)
> +{
> + struct genpd_onecell_data *genpd_data;
> + struct resource *res;
> + int i;
> +
> + genpd_data = devm_kzalloc(&pdev->dev, sizeof(*genpd_data), GFP_KERNEL);
> + if (!genpd_data)
> + return -ENOMEM;
> +
> + genpd_data->domains = zx_pm_domains;
> + genpd_data->num_domains = domain_num;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + pcubase = devm_ioremap_resource(&pdev->dev, res);
> + if (IS_ERR(pcubase)) {
> + dev_err(&pdev->dev, "ioremap fail.\n");
> + return PTR_ERR(pcubase);
> + }
> +
> + for (i = 0; i < domain_num; ++i)
> + pm_genpd_init(zx_pm_domains[i], NULL, false);
> +
> + of_genpd_add_provider_onecell(pdev->dev.of_node, genpd_data);
> + dev_info(&pdev->dev, "powerdomain init ok\n");
> + return 0;
> +}
> diff --git a/drivers/soc/zte/zx2967_pm_domains.h b/drivers/soc/zte/zx2967_pm_domains.h
> new file mode 100644
> index 0000000..81ad4d6
> --- /dev/null
> +++ b/drivers/soc/zte/zx2967_pm_domains.h
> @@ -0,0 +1,46 @@
> +/*
> + * Header for ZTE's Power Domain Driver support
> + *
> + * Copyright (C) 2017 ZTE Ltd.
> + *
> + * Author: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> + * License terms: GNU General Public License (GPL) version 2
> + */
> +
> +#ifndef __ZTE_ZX2967_PM_DOMAIN_H
> +#define __ZTE_ZX2967_PM_DOMAIN_H
> +
> +#include <linux/platform_device.h>
> +#include <linux/pm_domain.h>
> +
> +enum {
> + REG_CLKEN,
> + REG_ISOEN,
> + REG_RSTEN,
> + REG_PWREN,
> + REG_PWRDN,
> + REG_ACK_SYNC,
> +
> + /* The size of the array - must be last */
> + REG_ARRAY_SIZE,
> +};
> +
> +enum zx2967_power_polarity {
> + PWREN,
> + PWRDN,
> +};
> +
> +struct zx2967_pm_domain {
> + struct generic_pm_domain dm;
> + const u16 bit;
> + const enum zx2967_power_polarity polarity;
> + const u16 *reg_offset;
> +};
> +
> +extern int zx2967_power_on(struct generic_pm_domain *domain);
> +extern int zx2967_power_off(struct generic_pm_domain *domain);
> +extern int zx2967_pd_probe(struct platform_device *pdev,
> + struct generic_pm_domain **zx_pm_domains,
> + int domain_num);
The 'extern' is not really necessary here.
Shawn
> +
> +#endif /* __ZTE_ZX2967_PM_DOMAIN_H */
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v5 3/4] soc: zte: pm_domains: Add support for zx296718 board
From: Shawn Guo @ 2017-01-04 5:49 UTC (permalink / raw)
To: Baoyou Xie
Cc: jun.nie-QSEj5FYQhm4dnm+yROfE0A, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8, gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
davem-fT/PcQaiUtIeIZ0/mPfg9Q,
geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ,
akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, linux-0h96xk9xTtrk1uMJSBkQmQ,
krzk-DgEjT+Ai2ygdnm+yROfE0A, arnd-r2nGTMty4D4,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A,
pankaj.dubey-Sze3O3UU22JBDgjK7y7TUQ, yangbo.lu-3arQi8VN3Tc,
f.fainelli-Re5JQEeQqe8AvxtiuMwx3w, claudiu.manoil-3arQi8VN3Tc,
laurent.pinchart+renesas-ryLnwIuWjnjg/C1BVhZhaw,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
xie.baoyou-Th6q7B73Y6EnDS1+zs4M5A,
chen.chaokai-Th6q7B73Y6EnDS1+zs4M5A,
wang.qiang01-Th6q7B73Y6EnDS1+zs4M5A
In-Reply-To: <1483489157-10782-3-git-send-email-baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
On Wed, Jan 04, 2017 at 08:19:16AM +0800, Baoyou Xie wrote:
> This patch introduces the power domain driver of zx296718
> which belongs to zte's zx2967 family.
>
> Signed-off-by: Baoyou Xie <baoyou.xie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Reviewed-by: Shawn Guo <shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Reviewed-by: Jun Nie <jun.nie-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Jun did give his Reviewed-by tag on v2 of this patch, but I did not.
Once again, I put quite a few comments on v3 of this patch [1]. But
neither you responded to nor address any of them in reposting.
Shawn
[1] http://www.spinics.net/lists/arm-kernel/msg547691.html
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH V5 1/3] dt-bindings: document common IEEE 802.11 frequency limit property
From: Rafał Miłecki @ 2017-01-04 6:20 UTC (permalink / raw)
To: Johannes Berg, linux-wireless-u79uwXL29TY76Z2rM5mHXA, Rob Herring
Cc: Martin Blumenstingl, Felix Fietkau, Arend van Spriel,
Arnd Bergmann, devicetree-u79uwXL29TY76Z2rM5mHXA,
Rafał Miłecki
In-Reply-To: <20170103225715.14072-1-zajec5-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Hi Rob,
On 01/03/2017 11:57 PM, Rafał Miłecki wrote:
> From: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
>
> This new file should be used for properties that apply to all wireless
> devices.
>
> Signed-off-by: Rafał Miłecki <rafal-g1n6cQUeyibVItvQsEIGlw@public.gmane.org>
> ---
> V2: Switch to a single ieee80211-freq-limit property that allows specifying
> *multiple* ranges. This resolves problem with more complex rules as pointed
> by Felx.
> Make description implementation agnostic as pointed by Arend.
> Rename node to wifi as suggested by Martin.
> V3: Use more real-life frequencies in the example.
> V5: Describe hardware design as possible use for this property
> ---
> .../devicetree/bindings/net/wireless/ieee80211.txt | 20 ++++++++++++++++++++
> 1 file changed, 20 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/wireless/ieee80211.txt
>
> diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt
> new file mode 100644
> index 0000000..1c82c16
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt
> @@ -0,0 +1,20 @@
> +Common IEEE 802.11 properties
> +
> +This provides documentation of common properties that are valid for all wireless
> +devices.
> +
> +Optional properties:
> + - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be
> + used to specify extra hardware limitations caused by e.g. used antennas
> + or power amplifiers.
Do you find this description sufficient now? I'm not sure how/if I could answer
"Where would this data normally come from?" question.
One vendor may hardcode choice of channels in their PHP web UI.
Another one may do it in Andoid app.
OpenWrt so far was describing this limitation on their wiki page.
It doesn't sound like any valuable info if I understand this correctly. We also
don't describe where to get information about amount o RAM. One may just check
the hardware, one may use vendor firmware, one could check product data sheet.
If I missed the point, could you help me get this?
> +Example:
> +
> +pcie@0,0 {
> + reg = <0x0000 0 0 0 0>;
> + wifi@0,0 {
> + reg = <0x0000 0 0 0 0>;
> + ieee80211-freq-limit = <2402000 2482000>,
> + <5170000 5250000>;
> + };
> +};
>
^ permalink raw reply
* Re: [PATCH 1/2] dt-bindings: leds: document new usb-ports property
From: Rafał Miłecki @ 2017-01-04 6:33 UTC (permalink / raw)
To: Rob Herring
Cc: Greg Kroah-Hartman, linux-usb, linux-leds, Richard Purdie,
Jacek Anaszewski, Pavel Machek, devicetree, Mark Rutland,
Rafał Miłecki
In-Reply-To: <20170103205202.5ztb5i56d7qmgx5t@rob-hp-laptop>
On 01/03/2017 09:52 PM, Rob Herring wrote:
> On Thu, Dec 29, 2016 at 02:03:04PM +0100, Rafał Miłecki wrote:
>> From: Rafał Miłecki <rafal@milecki.pl>
>>
>> Some LEDs can be related to particular USB ports (common case for home
>> routers). This property allows describing such a relation.
>>
>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
>> ---
>> This patch is based on top of commit 52e847dc431 ("DT: leds: Improve examples
>> by adding some context") sitting in the linux-leds.git (for-4.11).
>> ---
>> Documentation/devicetree/bindings/leds/common.txt | 13 +++++++++++++
>> 1 file changed, 13 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt
>> index 24b6560..fcfe661 100644
>> --- a/Documentation/devicetree/bindings/leds/common.txt
>> +++ b/Documentation/devicetree/bindings/leds/common.txt
>> @@ -49,6 +49,14 @@ Optional properties for child nodes:
>> - panic-indicator : This property specifies that the LED should be used,
>> if at all possible, as a panic indicator.
>>
>> +- usb-ports : List of USB ports related to this LED. Some devices have LEDs that
>> + should be used to indicate USB device activity. This can be
>> + described with this property.
>> + There can be more than one LED like this, e.g. some vendors use
>> + one controller per USB version. It's then common to use different
>> + color LEDs depending on device USB standard (like USB 2.0 vs.
>> + USB 3.0).
>
> I don't like this being USB specific. Either we should have a generic
> way to link triggers to other DT nodes or the existing trigger property
> should be used (and be capable of listing more than 1 port). I'd prefer
> the latter as I don't think we need another way to specify triggers.
Hi Rob & thanks for your review.
Could you point me to "the existing trigger property" you meant, please? It's
not clear to me, sorry.
^ permalink raw reply
* [PATCH v3 0/3] dmaengine: xilinx_dma: Bug fixes
From: Kedareswara rao Appana @ 2017-01-04 6:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, dan.j.williams, vinod.koul, michal.simek,
soren.brinkmann, appanad, moritz.fischer, laurent.pinchart, luis,
Jose.Abreu
Cc: dmaengine, devicetree, linux-kernel, linux-arm-kernel
This patch series fixes below bugs in DMA and VDMA IP's
---> Do not start VDMA until frame buffer is processed by the h/w Fix
---> bug in Multi frame sotres handling in VDMA Fix issues w.r.to multi
---> frame descriptors submit with AXI DMA S2MM(recv) Side.
Kedareswara rao Appana (3):
dmaengine: xilinx_dma: Check for channel idle state before submitting
dma descriptor
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in
vdma
dmaengine: xilinx_dma: Fix race condition in the driver for multiple
descriptor scenario
.../devicetree/bindings/dma/xilinx/xilinx_dma.txt | 2 +
drivers/dma/xilinx/xilinx_dma.c | 265 ++++++++++++---------
2 files changed, 156 insertions(+), 111 deletions(-)
--
2.1.2
^ permalink raw reply
* [PATCH v3 1/3] dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
From: Kedareswara rao Appana @ 2017-01-04 6:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, dan.j.williams, vinod.koul, michal.simek,
soren.brinkmann, appanad, moritz.fischer, laurent.pinchart, luis,
Jose.Abreu
Cc: dmaengine, devicetree, linux-kernel, linux-arm-kernel
In-Reply-To: <1483512847-25710-1-git-send-email-appanad@xilinx.com>
Add channel idle state to ensure that dma descriptor is not
submitted when VDMA engine is in progress.
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
---
Changes for v3:
---> None.
Changes for v2:
---> Add idle check in the reset as suggested by Jose Abreu
---> Removed xilinx_dma_is_running/xilinx_dma_is_idle checks
in the driver and used common idle checks across the driver
as suggested by Laurent Pinchart.
drivers/dma/xilinx/xilinx_dma.c | 56 +++++++++++++----------------------------
1 file changed, 17 insertions(+), 39 deletions(-)
diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
index 8288fe4..be7eb41 100644
--- a/drivers/dma/xilinx/xilinx_dma.c
+++ b/drivers/dma/xilinx/xilinx_dma.c
@@ -321,6 +321,7 @@ struct xilinx_dma_tx_descriptor {
* @cyclic: Check for cyclic transfers.
* @genlock: Support genlock mode
* @err: Channel has errors
+ * @idle: Check for channel idle
* @tasklet: Cleanup work after irq
* @config: Device configuration info
* @flush_on_fsync: Flush on Frame sync
@@ -351,6 +352,7 @@ struct xilinx_dma_chan {
bool cyclic;
bool genlock;
bool err;
+ bool idle;
struct tasklet_struct tasklet;
struct xilinx_vdma_config config;
bool flush_on_fsync;
@@ -920,32 +922,6 @@ static enum dma_status xilinx_dma_tx_status(struct dma_chan *dchan,
}
/**
- * xilinx_dma_is_running - Check if DMA channel is running
- * @chan: Driver specific DMA channel
- *
- * Return: '1' if running, '0' if not.
- */
-static bool xilinx_dma_is_running(struct xilinx_dma_chan *chan)
-{
- return !(dma_ctrl_read(chan, XILINX_DMA_REG_DMASR) &
- XILINX_DMA_DMASR_HALTED) &&
- (dma_ctrl_read(chan, XILINX_DMA_REG_DMACR) &
- XILINX_DMA_DMACR_RUNSTOP);
-}
-
-/**
- * xilinx_dma_is_idle - Check if DMA channel is idle
- * @chan: Driver specific DMA channel
- *
- * Return: '1' if idle, '0' if not.
- */
-static bool xilinx_dma_is_idle(struct xilinx_dma_chan *chan)
-{
- return dma_ctrl_read(chan, XILINX_DMA_REG_DMASR) &
- XILINX_DMA_DMASR_IDLE;
-}
-
-/**
* xilinx_dma_halt - Halt DMA channel
* @chan: Driver specific DMA channel
*/
@@ -966,6 +942,7 @@ static void xilinx_dma_halt(struct xilinx_dma_chan *chan)
chan, dma_ctrl_read(chan, XILINX_DMA_REG_DMASR));
chan->err = true;
}
+ chan->idle = true;
}
/**
@@ -1007,6 +984,9 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
if (chan->err)
return;
+ if (!chan->idle)
+ return;
+
if (list_empty(&chan->pending_list))
return;
@@ -1018,13 +998,6 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
tail_segment = list_last_entry(&tail_desc->segments,
struct xilinx_vdma_tx_segment, node);
- /* If it is SG mode and hardware is busy, cannot submit */
- if (chan->has_sg && xilinx_dma_is_running(chan) &&
- !xilinx_dma_is_idle(chan)) {
- dev_dbg(chan->dev, "DMA controller still busy\n");
- return;
- }
-
/*
* If hardware is idle, then all descriptors on the running lists are
* done, start new transfers
@@ -1110,6 +1083,7 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
vdma_desc_write(chan, XILINX_DMA_REG_VSIZE, last->hw.vsize);
}
+ chan->idle = false;
if (!chan->has_sg) {
list_del(&desc->node);
list_add_tail(&desc->node, &chan->active_list);
@@ -1136,6 +1110,9 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
if (chan->err)
return;
+ if (!chan->idle)
+ return;
+
if (list_empty(&chan->pending_list))
return;
@@ -1181,6 +1158,7 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
list_splice_tail_init(&chan->pending_list, &chan->active_list);
chan->desc_pendingcount = 0;
+ chan->idle = false;
}
/**
@@ -1196,15 +1174,11 @@ static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
if (chan->err)
return;
- if (list_empty(&chan->pending_list))
+ if (!chan->idle)
return;
- /* If it is SG mode and hardware is busy, cannot submit */
- if (chan->has_sg && xilinx_dma_is_running(chan) &&
- !xilinx_dma_is_idle(chan)) {
- dev_dbg(chan->dev, "DMA controller still busy\n");
+ if (list_empty(&chan->pending_list))
return;
- }
head_desc = list_first_entry(&chan->pending_list,
struct xilinx_dma_tx_descriptor, node);
@@ -1302,6 +1276,7 @@ static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
list_splice_tail_init(&chan->pending_list, &chan->active_list);
chan->desc_pendingcount = 0;
+ chan->idle = false;
}
/**
@@ -1366,6 +1341,7 @@ static int xilinx_dma_reset(struct xilinx_dma_chan *chan)
}
chan->err = false;
+ chan->idle = true;
return err;
}
@@ -1447,6 +1423,7 @@ static irqreturn_t xilinx_dma_irq_handler(int irq, void *data)
if (status & XILINX_DMA_DMASR_FRM_CNT_IRQ) {
spin_lock(&chan->lock);
xilinx_dma_complete_descriptor(chan);
+ chan->idle = true;
chan->start_transfer(chan);
spin_unlock(&chan->lock);
}
@@ -2327,6 +2304,7 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
chan->has_sg = xdev->has_sg;
chan->desc_pendingcount = 0x0;
chan->ext_addr = xdev->ext_addr;
+ chan->idle = true;
spin_lock_init(&chan->lock);
INIT_LIST_HEAD(&chan->pending_list);
--
2.1.2
^ permalink raw reply related
* [PATCH v3 2/3] dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
From: Kedareswara rao Appana @ 2017-01-04 6:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, dan.j.williams, vinod.koul, michal.simek,
soren.brinkmann, appanad, moritz.fischer, laurent.pinchart, luis,
Jose.Abreu
Cc: dmaengine, devicetree, linux-kernel, linux-arm-kernel
In-Reply-To: <1483512847-25710-1-git-send-email-appanad@xilinx.com>
When VDMA is configured for more than one frame in the h/w
for example h/w is configured for n number of frames and user
Submits n number of frames and triggered the DMA using issue_pending API.
In the current driver flow we are submitting one frame at a time
but we should submit all the n number of frames at one time as the h/w
Is configured for n number of frames.
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
---
Changes for v3:
---> Added Checks for frame store configuration. If frame store
Configuration is not present at the h/w level and user
Submits less frames added debug prints in the driver as relevant.
Changes for v2:
---> Fixed race conditions in the driver as suggested by Jose Abreu
---> Fixed unnecessray if else checks in the vdma_start_transfer
as suggested by Laurent Pinchart.
.../devicetree/bindings/dma/xilinx/xilinx_dma.txt | 2 +
drivers/dma/xilinx/xilinx_dma.c | 78 +++++++++++++++-------
2 files changed, 57 insertions(+), 23 deletions(-)
diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
index a2b8bfa..1f65e09 100644
--- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
+++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt
@@ -66,6 +66,8 @@ Optional child node properties:
Optional child node properties for VDMA:
- xlnx,genlock-mode: Tells Genlock synchronization is
enabled/disabled in hardware.
+- xlnx,fstore-config: Tells Whether Frame Store Configuration is
+ enabled/disabled in hardware.
Optional child node properties for AXI DMA:
-dma-channels: Number of dma channels in child node.
diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
index be7eb41..7cd8e08 100644
--- a/drivers/dma/xilinx/xilinx_dma.c
+++ b/drivers/dma/xilinx/xilinx_dma.c
@@ -322,6 +322,7 @@ struct xilinx_dma_tx_descriptor {
* @genlock: Support genlock mode
* @err: Channel has errors
* @idle: Check for channel idle
+ * @has_fstoreconfig: Check for frame store configuration
* @tasklet: Cleanup work after irq
* @config: Device configuration info
* @flush_on_fsync: Flush on Frame sync
@@ -353,6 +354,7 @@ struct xilinx_dma_chan {
bool genlock;
bool err;
bool idle;
+ bool has_fstoreconfig;
struct tasklet_struct tasklet;
struct xilinx_vdma_config config;
bool flush_on_fsync;
@@ -990,6 +992,26 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
if (list_empty(&chan->pending_list))
return;
+ /*
+ * Note: When VDMA is built with default h/w configuration
+ * On the S2MM(recv) side user should submit frames upto
+ * H/W configured. If users submits less than h/w configured
+ * VDMA engine tries to write to a invalid location
+ * Results undefined behaviour/memory corruption.
+ *
+ * If user would like to submit frames less than h/w capable
+ * On S2MM side please enable debug info 13 at the h/w level
+ * It will allows the frame buffers numbers to be modified at runtime.
+ */
+ if (!chan->has_fstoreconfig && chan->direction == DMA_DEV_TO_MEM &&
+ chan->desc_pendingcount < chan->num_frms) {
+ dev_dbg(chan->dev, "Frame Store Configuration is not enabled at the");
+ dev_dbg(chan->dev, " H/w level enable Debug info 13 at the h/w level");
+ dev_dbg(chan->dev, " OR Submit the frames upto h/w Capable\n\r");
+
+ return;
+ }
+
desc = list_first_entry(&chan->pending_list,
struct xilinx_dma_tx_descriptor, node);
tail_desc = list_last_entry(&chan->pending_list,
@@ -1052,25 +1074,38 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
if (chan->has_sg) {
dma_ctrl_write(chan, XILINX_DMA_REG_TAILDESC,
tail_segment->phys);
+ list_splice_tail_init(&chan->pending_list, &chan->active_list);
+ chan->desc_pendingcount = 0;
} else {
struct xilinx_vdma_tx_segment *segment, *last = NULL;
- int i = 0;
+ int i = 0, j = 0;
if (chan->desc_submitcount < chan->num_frms)
i = chan->desc_submitcount;
- list_for_each_entry(segment, &desc->segments, node) {
- if (chan->ext_addr)
- vdma_desc_write_64(chan,
- XILINX_VDMA_REG_START_ADDRESS_64(i++),
- segment->hw.buf_addr,
- segment->hw.buf_addr_msb);
- else
- vdma_desc_write(chan,
- XILINX_VDMA_REG_START_ADDRESS(i++),
- segment->hw.buf_addr);
-
- last = segment;
+ for (j = 0; j < chan->num_frms; ) {
+ list_for_each_entry(segment, &desc->segments, node) {
+ if (chan->ext_addr)
+ vdma_desc_write_64(chan,
+ XILINX_VDMA_REG_START_ADDRESS_64(i++),
+ segment->hw.buf_addr,
+ segment->hw.buf_addr_msb);
+ else
+ vdma_desc_write(chan,
+ XILINX_VDMA_REG_START_ADDRESS(i++),
+ segment->hw.buf_addr);
+
+ last = segment;
+ }
+ list_del(&desc->node);
+ list_add_tail(&desc->node, &chan->active_list);
+ j++;
+ if (list_empty(&chan->pending_list) ||
+ (i == chan->num_frms))
+ break;
+ desc = list_first_entry(&chan->pending_list,
+ struct xilinx_dma_tx_descriptor,
+ node);
}
if (!last)
@@ -1081,20 +1116,14 @@ static void xilinx_vdma_start_transfer(struct xilinx_dma_chan *chan)
vdma_desc_write(chan, XILINX_DMA_REG_FRMDLY_STRIDE,
last->hw.stride);
vdma_desc_write(chan, XILINX_DMA_REG_VSIZE, last->hw.vsize);
- }
- chan->idle = false;
- if (!chan->has_sg) {
- list_del(&desc->node);
- list_add_tail(&desc->node, &chan->active_list);
- chan->desc_submitcount++;
- chan->desc_pendingcount--;
+ chan->desc_submitcount += j;
+ chan->desc_pendingcount -= j;
if (chan->desc_submitcount == chan->num_frms)
chan->desc_submitcount = 0;
- } else {
- list_splice_tail_init(&chan->pending_list, &chan->active_list);
- chan->desc_pendingcount = 0;
}
+
+ chan->idle = false;
}
/**
@@ -1342,6 +1371,7 @@ static int xilinx_dma_reset(struct xilinx_dma_chan *chan)
chan->err = false;
chan->idle = true;
+ chan->desc_submitcount = 0;
return err;
}
@@ -2315,6 +2345,8 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
has_dre = of_property_read_bool(node, "xlnx,include-dre");
chan->genlock = of_property_read_bool(node, "xlnx,genlock-mode");
+ chan->has_fstoreconfig = of_property_read_bool(node,
+ "xlnx,fstore-config");
err = of_property_read_u32(node, "xlnx,datawidth", &value);
if (err) {
--
2.1.2
^ permalink raw reply related
* [PATCH v3 3/3] dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
From: Kedareswara rao Appana @ 2017-01-04 6:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, dan.j.williams, vinod.koul, michal.simek,
soren.brinkmann, appanad, moritz.fischer, laurent.pinchart, luis,
Jose.Abreu
Cc: dmaengine, devicetree, linux-kernel, linux-arm-kernel
In-Reply-To: <1483512847-25710-1-git-send-email-appanad@xilinx.com>
When driver is handling AXI DMA SoftIP
When user submits multiple descriptors back to back on the S2MM(recv)
side with the current driver flow the last buffer descriptor next bd
points to a invalid location resulting the invalid data or errors in the
DMA engine.
This patch fixes this issue by creating a BD Chain during
channel allocation itself and use those BD's.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
---
Changes for v3:
---> None.
Changes for v2:
---> None.
drivers/dma/xilinx/xilinx_dma.c | 133 +++++++++++++++++++++++++---------------
1 file changed, 83 insertions(+), 50 deletions(-)
diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
index 7cd8e08..822ccf00 100644
--- a/drivers/dma/xilinx/xilinx_dma.c
+++ b/drivers/dma/xilinx/xilinx_dma.c
@@ -163,6 +163,7 @@
#define XILINX_DMA_BD_SOP BIT(27)
#define XILINX_DMA_BD_EOP BIT(26)
#define XILINX_DMA_COALESCE_MAX 255
+#define XILINX_DMA_NUM_DESCS 255
#define XILINX_DMA_NUM_APP_WORDS 5
/* Multi-Channel DMA Descriptor offsets*/
@@ -310,6 +311,7 @@ struct xilinx_dma_tx_descriptor {
* @pending_list: Descriptors waiting
* @active_list: Descriptors ready to submit
* @done_list: Complete descriptors
+ * @free_seg_list: Free descriptors
* @common: DMA common channel
* @desc_pool: Descriptors pool
* @dev: The dma device
@@ -331,7 +333,9 @@ struct xilinx_dma_tx_descriptor {
* @desc_submitcount: Descriptor h/w submitted count
* @residue: Residue for AXI DMA
* @seg_v: Statically allocated segments base
+ * @seg_p: Physical allocated segments base
* @cyclic_seg_v: Statically allocated segment base for cyclic transfers
+ * @cyclic_seg_p: Physical allocated segments base for cyclic dma
* @start_transfer: Differentiate b/w DMA IP's transfer
*/
struct xilinx_dma_chan {
@@ -342,6 +346,7 @@ struct xilinx_dma_chan {
struct list_head pending_list;
struct list_head active_list;
struct list_head done_list;
+ struct list_head free_seg_list;
struct dma_chan common;
struct dma_pool *desc_pool;
struct device *dev;
@@ -363,7 +368,9 @@ struct xilinx_dma_chan {
u32 desc_submitcount;
u32 residue;
struct xilinx_axidma_tx_segment *seg_v;
+ dma_addr_t seg_p;
struct xilinx_axidma_tx_segment *cyclic_seg_v;
+ dma_addr_t cyclic_seg_p;
void (*start_transfer)(struct xilinx_dma_chan *chan);
u16 tdest;
};
@@ -569,17 +576,31 @@ static struct xilinx_axidma_tx_segment *
xilinx_axidma_alloc_tx_segment(struct xilinx_dma_chan *chan)
{
struct xilinx_axidma_tx_segment *segment;
- dma_addr_t phys;
-
- segment = dma_pool_zalloc(chan->desc_pool, GFP_ATOMIC, &phys);
- if (!segment)
- return NULL;
+ unsigned long flags;
- segment->phys = phys;
+ spin_lock_irqsave(&chan->lock, flags);
+ if (!list_empty(&chan->free_seg_list)) {
+ segment = list_first_entry(&chan->free_seg_list,
+ struct xilinx_axidma_tx_segment,
+ node);
+ list_del(&segment->node);
+ }
+ spin_unlock_irqrestore(&chan->lock, flags);
return segment;
}
+static void xilinx_dma_clean_hw_desc(struct xilinx_axidma_desc_hw *hw)
+{
+ u32 next_desc = hw->next_desc;
+ u32 next_desc_msb = hw->next_desc_msb;
+
+ memset(hw, 0, sizeof(struct xilinx_axidma_desc_hw));
+
+ hw->next_desc = next_desc;
+ hw->next_desc_msb = next_desc_msb;
+}
+
/**
* xilinx_dma_free_tx_segment - Free transaction segment
* @chan: Driver specific DMA channel
@@ -588,7 +609,9 @@ xilinx_axidma_alloc_tx_segment(struct xilinx_dma_chan *chan)
static void xilinx_dma_free_tx_segment(struct xilinx_dma_chan *chan,
struct xilinx_axidma_tx_segment *segment)
{
- dma_pool_free(chan->desc_pool, segment, segment->phys);
+ xilinx_dma_clean_hw_desc(&segment->hw);
+
+ list_add_tail(&segment->node, &chan->free_seg_list);
}
/**
@@ -713,16 +736,26 @@ static void xilinx_dma_free_descriptors(struct xilinx_dma_chan *chan)
static void xilinx_dma_free_chan_resources(struct dma_chan *dchan)
{
struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
+ unsigned long flags;
dev_dbg(chan->dev, "Free all channel resources.\n");
xilinx_dma_free_descriptors(chan);
+
if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
- xilinx_dma_free_tx_segment(chan, chan->cyclic_seg_v);
- xilinx_dma_free_tx_segment(chan, chan->seg_v);
+ spin_lock_irqsave(&chan->lock, flags);
+ INIT_LIST_HEAD(&chan->free_seg_list);
+ spin_unlock_irqrestore(&chan->lock, flags);
+
+ /* Free Memory that is allocated for cyclic DMA Mode */
+ dma_free_coherent(chan->dev, sizeof(*chan->cyclic_seg_v),
+ chan->cyclic_seg_v, chan->cyclic_seg_p);
+ }
+
+ if (chan->xdev->dma_config->dmatype != XDMA_TYPE_AXIDMA) {
+ dma_pool_destroy(chan->desc_pool);
+ chan->desc_pool = NULL;
}
- dma_pool_destroy(chan->desc_pool);
- chan->desc_pool = NULL;
}
/**
@@ -805,6 +838,7 @@ static void xilinx_dma_do_tasklet(unsigned long data)
static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
{
struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
+ int i;
/* Has this channel already been allocated? */
if (chan->desc_pool)
@@ -815,11 +849,30 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
* for meeting Xilinx VDMA specification requirement.
*/
if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
- chan->desc_pool = dma_pool_create("xilinx_dma_desc_pool",
- chan->dev,
- sizeof(struct xilinx_axidma_tx_segment),
- __alignof__(struct xilinx_axidma_tx_segment),
- 0);
+ /* Allocate the buffer descriptors. */
+ chan->seg_v = dma_zalloc_coherent(chan->dev,
+ sizeof(*chan->seg_v) *
+ XILINX_DMA_NUM_DESCS,
+ &chan->seg_p, GFP_KERNEL);
+ if (!chan->seg_v) {
+ dev_err(chan->dev,
+ "unable to allocate channel %d descriptors\n",
+ chan->id);
+ return -ENOMEM;
+ }
+
+ for (i = 0; i < XILINX_DMA_NUM_DESCS; i++) {
+ chan->seg_v[i].hw.next_desc =
+ lower_32_bits(chan->seg_p + sizeof(*chan->seg_v) *
+ ((i + 1) % XILINX_DMA_NUM_DESCS));
+ chan->seg_v[i].hw.next_desc_msb =
+ upper_32_bits(chan->seg_p + sizeof(*chan->seg_v) *
+ ((i + 1) % XILINX_DMA_NUM_DESCS));
+ chan->seg_v[i].phys = chan->seg_p +
+ sizeof(*chan->seg_v) * i;
+ list_add_tail(&chan->seg_v[i].node,
+ &chan->free_seg_list);
+ }
} else if (chan->xdev->dma_config->dmatype == XDMA_TYPE_CDMA) {
chan->desc_pool = dma_pool_create("xilinx_cdma_desc_pool",
chan->dev,
@@ -834,7 +887,8 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
0);
}
- if (!chan->desc_pool) {
+ if (!chan->desc_pool &&
+ (chan->xdev->dma_config->dmatype != XDMA_TYPE_AXIDMA)) {
dev_err(chan->dev,
"unable to allocate channel %d descriptor pool\n",
chan->id);
@@ -843,22 +897,20 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
/*
- * For AXI DMA case after submitting a pending_list, keep
- * an extra segment allocated so that the "next descriptor"
- * pointer on the tail descriptor always points to a
- * valid descriptor, even when paused after reaching taildesc.
- * This way, it is possible to issue additional
- * transfers without halting and restarting the channel.
- */
- chan->seg_v = xilinx_axidma_alloc_tx_segment(chan);
-
- /*
* For cyclic DMA mode we need to program the tail Descriptor
* register with a value which is not a part of the BD chain
* so allocating a desc segment during channel allocation for
* programming tail descriptor.
*/
- chan->cyclic_seg_v = xilinx_axidma_alloc_tx_segment(chan);
+ chan->cyclic_seg_v = dma_zalloc_coherent(chan->dev,
+ sizeof(*chan->cyclic_seg_v),
+ &chan->cyclic_seg_p, GFP_KERNEL);
+ if (!chan->cyclic_seg_v) {
+ dev_err(chan->dev,
+ "unable to allocate desc segment for cyclic DMA\n");
+ return -ENOMEM;
+ }
+ chan->cyclic_seg_v->phys = chan->cyclic_seg_p;
}
dma_cookie_init(dchan);
@@ -1197,7 +1249,7 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
{
struct xilinx_dma_tx_descriptor *head_desc, *tail_desc;
- struct xilinx_axidma_tx_segment *tail_segment, *old_head, *new_head;
+ struct xilinx_axidma_tx_segment *tail_segment;
u32 reg;
if (chan->err)
@@ -1216,21 +1268,6 @@ static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
tail_segment = list_last_entry(&tail_desc->segments,
struct xilinx_axidma_tx_segment, node);
- if (chan->has_sg && !chan->xdev->mcdma) {
- old_head = list_first_entry(&head_desc->segments,
- struct xilinx_axidma_tx_segment, node);
- new_head = chan->seg_v;
- /* Copy Buffer Descriptor fields. */
- new_head->hw = old_head->hw;
-
- /* Swap and save new reserve */
- list_replace_init(&old_head->node, &new_head->node);
- chan->seg_v = old_head;
-
- tail_segment->hw.next_desc = chan->seg_v->phys;
- head_desc->async_tx.phys = new_head->phys;
- }
-
reg = dma_ctrl_read(chan, XILINX_DMA_REG_DMACR);
if (chan->desc_pendingcount <= XILINX_DMA_COALESCE_MAX) {
@@ -1728,7 +1765,7 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
{
struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
struct xilinx_dma_tx_descriptor *desc;
- struct xilinx_axidma_tx_segment *segment = NULL, *prev = NULL;
+ struct xilinx_axidma_tx_segment *segment = NULL;
u32 *app_w = (u32 *)context;
struct scatterlist *sg;
size_t copy;
@@ -1779,10 +1816,6 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
XILINX_DMA_NUM_APP_WORDS);
}
- if (prev)
- prev->hw.next_desc = segment->phys;
-
- prev = segment;
sg_used += copy;
/*
@@ -1796,7 +1829,6 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
segment = list_first_entry(&desc->segments,
struct xilinx_axidma_tx_segment, node);
desc->async_tx.phys = segment->phys;
- prev->hw.next_desc = segment->phys;
/* For the last DMA_MEM_TO_DEV transfer, set EOP */
if (chan->direction == DMA_MEM_TO_DEV) {
@@ -2340,6 +2372,7 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
INIT_LIST_HEAD(&chan->pending_list);
INIT_LIST_HEAD(&chan->done_list);
INIT_LIST_HEAD(&chan->active_list);
+ INIT_LIST_HEAD(&chan->free_seg_list);
/* Retrieve the channel properties from the device tree */
has_dre = of_property_read_bool(node, "xlnx,include-dre");
--
2.1.2
^ permalink raw reply related
* [PATCH v4 0/3] Add support for the S6E3HA2 panel on TM2 board
From: Hoegeun Kwon @ 2017-01-04 6:58 UTC (permalink / raw)
To: robh-DgEjT+Ai2ygdnm+yROfE0A,
thierry.reding-Re5JQEeQqe8AvxtiuMwx3w, airlied-cv59FeDIM0c,
kgene-DgEjT+Ai2ygdnm+yROfE0A, krzk-DgEjT+Ai2ygdnm+yROfE0A,
inki.dae-Sze3O3UU22JBDgjK7y7TUQ
Cc: dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-samsung-soc-u79uwXL29TY76Z2rM5mHXA,
a.hajda-Sze3O3UU22JBDgjK7y7TUQ, cw00.choi-Sze3O3UU22JBDgjK7y7TUQ,
jh80.chung-Sze3O3UU22JBDgjK7y7TUQ, Hoegeun Kwon
In-Reply-To: <CGME20170104065858epcas5p2f6a70e125b1b6d7051d8fe3a28e626f5@epcas5p2.samsung.com>
Purpose of this patch is add support for S6E3HA2 AMOLED panel on
the TM2 board. The first patch adds support for S6E3HA2 panel
device tree document and driver, the second patch add support for
S6E3HA2 panel device tree.
Changes for V4:
- Removed display-timings in devicetree, the display-timings has
been fixed to be provided by the device driver.
- Added the mode_set callback function into exynos_drm_mic,
because the exynos_drm_mic driver can not parse a videomode
struct by removing the display-timings from the devicetree.
Hoegeun Kwon (2):
drm/exynos: mic: Add mode_set callback function
drm/panel: Add support for S6E3HA2 panel driver on TM2 board
Hyungwon Hwang (1):
arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board
.../bindings/display/panel/samsung,s6e3ha2.txt | 40 ++
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 17 +
drivers/gpu/drm/exynos/exynos_drm_mic.c | 33 +-
drivers/gpu/drm/panel/Kconfig | 6 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 741 +++++++++++++++++++++
6 files changed, 827 insertions(+), 11 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH v4 1/3] drm/exynos: mic: Add mode_set callback function
From: Hoegeun Kwon @ 2017-01-04 6:58 UTC (permalink / raw)
To: robh, thierry.reding, airlied, kgene, krzk, inki.dae
Cc: devicetree, linux-samsung-soc, linux-kernel, dri-devel,
jh80.chung, cw00.choi, Hoegeun Kwon
In-Reply-To: <1483513115-3068-1-git-send-email-hoegeun.kwon@samsung.com>
Before applying the patch, used the of_get_videomode function to
parse the display-timings in the panel which is the child driver
of dsi in the devicetree. this is wrong. So removed the
of_get_videomode and fixed to get videomode struct through
mode_set callback function.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_mic.c | 33 ++++++++++++++++++++++-----------
1 file changed, 22 insertions(+), 11 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_mic.c b/drivers/gpu/drm/exynos/exynos_drm_mic.c
index a0def0b..9a50ceb 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_mic.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_mic.c
@@ -286,13 +286,6 @@ static int parse_dt(struct exynos_mic *mic)
}
nodes[j++] = remote_node;
- ret = of_get_videomode(remote_node,
- &mic->vm, 0);
- if (ret) {
- DRM_ERROR("mic: failed to get videomode");
- goto exit;
- }
-
break;
default:
DRM_ERROR("mic: Unknown endpoint from MIC");
@@ -329,6 +322,27 @@ static void mic_post_disable(struct drm_bridge *bridge)
mutex_unlock(&mic_mutex);
}
+static void mic_mode_set(struct drm_bridge *bridge,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct exynos_mic *mic = bridge->driver_private;
+
+ mutex_lock(&mic_mutex);
+ if (mic->enabled)
+ goto already_enabled;
+
+ drm_display_mode_to_videomode(mode, &mic->vm);
+
+ if (!mic->i80_mode)
+ mic_set_porch_timing(mic);
+ mic_set_img_size(mic);
+ mic_set_output_timing(mic);
+
+already_enabled:
+ mutex_unlock(&mic_mutex);
+}
+
static void mic_pre_enable(struct drm_bridge *bridge)
{
struct exynos_mic *mic = bridge->driver_private;
@@ -355,10 +369,6 @@ static void mic_pre_enable(struct drm_bridge *bridge)
goto turn_off_clks;
}
- if (!mic->i80_mode)
- mic_set_porch_timing(mic);
- mic_set_img_size(mic);
- mic_set_output_timing(mic);
mic_set_reg_on(mic, 1);
mic->enabled = 1;
mutex_unlock(&mic_mutex);
@@ -377,6 +387,7 @@ static void mic_enable(struct drm_bridge *bridge) { }
static const struct drm_bridge_funcs mic_bridge_funcs = {
.disable = mic_disable,
.post_disable = mic_post_disable,
+ .mode_set = mic_mode_set,
.pre_enable = mic_pre_enable,
.enable = mic_enable,
};
--
1.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related
* [PATCH v4 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board
From: Hoegeun Kwon @ 2017-01-04 6:58 UTC (permalink / raw)
To: robh, thierry.reding, airlied, kgene, krzk, inki.dae
Cc: devicetree, linux-samsung-soc, Donghwa Lee, linux-kernel,
dri-devel, jh80.chung, cw00.choi, Hyungwon Hwang, Hoegeun Kwon
In-Reply-To: <1483513115-3068-1-git-send-email-hoegeun.kwon@samsung.com>
This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
driver. This panel has 1440x2560 resolution in 5.7-inch physical
panel in the TM2 device.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
---
.../bindings/display/panel/samsung,s6e3ha2.txt | 40 ++
drivers/gpu/drm/panel/Kconfig | 6 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 741 +++++++++++++++++++++
4 files changed, 788 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
new file mode 100644
index 0000000..6879f51
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
@@ -0,0 +1,40 @@
+Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
+
+Required properties:
+ - compatible: "samsung,s6e3ha2"
+ - reg: the virtual channel number of a DSI peripheral
+ - vdd3-supply: I/O voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpios: a GPIO spec for the reset pin (active low)
+ - enable-gpios: a GPIO spec for the panel enable pin (active high)
+ - te-gpios: a GPIO spec for the tearing effect synchronization signal
+ gpio pin (active high)
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [1]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+&dsi {
+ ...
+
+ panel@0 {
+ compatible = "samsung,s6e3ha2";
+ reg = <0>;
+ vdd3-supply = <&ldo27_reg>;
+ vci-supply = <&ldo28_reg>;
+ reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+ te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
+};
+
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 62aba97..eea2902 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00
WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some
Xperia Z2 tablets
+config DRM_PANEL_SAMSUNG_S6E3HA2
+ tristate "Samsung S6E3HA2 DSI video mode panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ select VIDEOMODE_HELPERS
+
config DRM_PANEL_SAMSUNG_S6E8AA0
tristate "Samsung S6E8AA0 DSI video mode panel"
depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index a5c7ec0..1d483b0 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
+obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o
obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o
obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
new file mode 100644
index 0000000..8c5a1c2
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
@@ -0,0 +1,741 @@
+/*
+ * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver.
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ * Donghwa Lee <dh09.lee@samsung.com>
+ * Hyungwon Hwang <human.hwang@samsung.com>
+ * Hoegeun Kwon <hoegeun.kwon@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <drm/drmP.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+#include <linux/backlight.h>
+#include <linux/gpio/consumer.h>
+#include <linux/regulator/consumer.h>
+
+#define S6E3HA2_MIN_BRIGHTNESS 0
+#define S6E3HA2_MAX_BRIGHTNESS 100
+#define S6E3HA2_DEFAULT_BRIGHTNESS 80
+
+#define S6E3HA2_NUM_GAMMA_STEPS 46
+#define S6E3HA2_GAMMA_CMD_CNT 35
+#define S6E3HA2_VINT_STATUS_MAX 10
+
+static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = {
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83,
+ 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c,
+ 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84,
+ 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a,
+ 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a,
+ 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a,
+ 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85,
+ 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b,
+ 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b,
+ 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89,
+ 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c,
+ 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88,
+ 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a,
+ 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b,
+ 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c,
+ 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c,
+ 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c,
+ 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c,
+ 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b,
+ 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
+ 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e,
+ 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e,
+ 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d,
+ 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
+ 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c,
+ 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83,
+ 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a,
+ 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83,
+ 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a,
+ 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83,
+ 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89,
+ 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83,
+ 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a,
+ 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82,
+ 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87,
+ 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82,
+ 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88,
+ 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83,
+ 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89,
+ 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82,
+ 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86,
+ 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82,
+ 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87,
+ 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81,
+ 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86,
+ 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82,
+ 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83,
+ 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82,
+ 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82,
+ 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80,
+ 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81,
+ 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83,
+ 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83,
+ 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82,
+ 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83,
+ 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83,
+ 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80,
+ 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81,
+ 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81,
+ 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83,
+ 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80,
+ 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80,
+ 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80,
+ 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d,
+ 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80,
+ 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82,
+ 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80,
+ 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
+ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80,
+ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
+ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 },
+ { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80,
+ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
+ 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
+ 0x00, 0x00 }
+};
+
+unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = {
+ 0x18, 0x19, 0x1a, 0x1b, 0x1c,
+ 0x1d, 0x1e, 0x1f, 0x20, 0x21
+};
+
+struct s6e3ha2 {
+ struct device *dev;
+ struct drm_panel panel;
+ struct backlight_device *bl_dev;
+
+ struct regulator_bulk_data supplies[2];
+ struct gpio_desc *reset_gpio;
+ struct gpio_desc *enable_gpio;
+
+ /* This field is tested by functions directly accessing DSI bus before
+ * transfer, transfer is skipped if it is set. In case of transfer
+ * failure or unexpected response the field is set to error value.
+ * Such construct allows to eliminate many checks in higher level
+ * functions.
+ */
+ int error;
+};
+
+static int s6e3ha2_clear_error(struct s6e3ha2 *ctx)
+{
+ int ret = ctx->error;
+
+ ctx->error = 0;
+ return ret;
+}
+
+static void s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ ssize_t ret;
+
+ if (ctx->error < 0)
+ return;
+
+ ret = mipi_dsi_dcs_write_buffer(dsi, data, len);
+ if (ret < 0) {
+ dev_err(ctx->dev, "error %zd writing dcs seq: %*ph\n",
+ ret, (int)len, data);
+ ctx->error = ret;
+ }
+}
+
+#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \
+ static const u8 d[] = { seq }; \
+ s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \
+} while (0)
+
+static void s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a);
+}
+
+static void s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5);
+}
+
+static void s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a);
+}
+
+static void s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5);
+}
+
+static void s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67);
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09);
+}
+
+static void s6e3ha2_freq_calibration(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c);
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39);
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0);
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20);
+ s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62,
+ 0x40, 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5);
+}
+
+static void s6e3ha2_aor_control(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10);
+}
+
+static void s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a);
+}
+
+static void s6e3ha2_acl_off(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00);
+}
+
+static void s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40);
+}
+
+static void s6e3ha2_test_global(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07);
+}
+
+static void s6e3ha2_test(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19);
+}
+
+static void s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx,
+ 0xbd, 0x33, 0x11, 0x02, 0x16, 0x02, 0x16);
+}
+
+static void s6e3ha2_pentile_control(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8);
+}
+
+static void s6e3ha2_poc_global(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20);
+}
+
+static void s6e3ha2_poc_setting(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08);
+}
+
+static void s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51);
+}
+
+static void s6e3ha2_err_fg_set(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44);
+}
+
+static void s6e3ha2_hbm_off(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00);
+}
+
+static void s6e3ha2_te_start_setting(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09);
+}
+
+static void s6e3ha2_gamma_update(struct s6e3ha2 *ctx)
+{
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03);
+ ndelay(100); /* need for 100ns delay */
+ s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00);
+}
+
+static int s6e3ha2_get_brightness(struct backlight_device *bl_dev)
+{
+ return bl_dev->props.brightness;
+}
+
+static void s6e3ha2_set_vint(struct s6e3ha2 *ctx)
+{
+ struct backlight_device *bl_dev = ctx->bl_dev;
+ unsigned int brightness = bl_dev->props.brightness;
+ unsigned char data[] = { 0xf4, 0x8b,
+ vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) /
+ S6E3HA2_MAX_BRIGHTNESS] };
+
+ s6e3ha2_dcs_write(ctx, data, 3);
+}
+
+static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness)
+{
+ return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) /
+ S6E3HA2_MAX_BRIGHTNESS;
+}
+
+static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness)
+{
+ struct backlight_device *bl_dev = ctx->bl_dev;
+ unsigned int index = s6e3ha2_get_brightness_index(brightness);
+ u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, };
+
+ memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT);
+ s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data));
+
+ s6e3ha2_gamma_update(ctx);
+ bl_dev->props.brightness = brightness;
+
+ return 0;
+}
+
+static int s6e3ha2_set_brightness(struct backlight_device *bl_dev)
+{
+ struct s6e3ha2 *ctx = (struct s6e3ha2 *)bl_get_data(bl_dev);
+ unsigned int brightness = bl_dev->props.brightness;
+
+ if (brightness < S6E3HA2_MIN_BRIGHTNESS ||
+ brightness > bl_dev->props.max_brightness) {
+ dev_err(ctx->dev, "Invalid brightness: %u\n", brightness);
+ return -EINVAL;
+ }
+
+ if (bl_dev->props.power > FB_BLANK_NORMAL)
+ return -EPERM;
+
+ s6e3ha2_test_key_on_f0(ctx);
+ s6e3ha2_update_gamma(ctx, brightness);
+ s6e3ha2_aor_control(ctx);
+ s6e3ha2_set_vint(ctx);
+ s6e3ha2_test_key_off_f0(ctx);
+
+ return ctx->error;
+}
+
+static const struct backlight_ops s6e3ha2_bl_ops = {
+ .get_brightness = s6e3ha2_get_brightness,
+ .update_status = s6e3ha2_set_brightness,
+};
+
+static void s6e3ha2_panel_init(struct s6e3ha2 *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ mipi_dsi_dcs_exit_sleep_mode(dsi);
+ usleep_range(5000, 6000);
+
+ s6e3ha2_test_key_on_f0(ctx);
+ s6e3ha2_single_dsi_set(ctx);
+ s6e3ha2_test_key_on_fc(ctx);
+ s6e3ha2_freq_calibration(ctx);
+ s6e3ha2_test_key_off_fc(ctx);
+ s6e3ha2_test_key_off_f0(ctx);
+}
+
+static int s6e3ha2_power_off(struct s6e3ha2 *ctx)
+{
+ return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+}
+
+static int s6e3ha2_disable(struct drm_panel *panel)
+{
+ struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ctx->error != 0)
+ goto err;
+
+ mipi_dsi_dcs_set_display_off(dsi);
+ if (ctx->error != 0)
+ goto err;
+
+ msleep(40);
+ ctx->bl_dev->props.power = FB_BLANK_NORMAL;
+
+ return 0;
+err:
+ return ctx->error;
+}
+
+static int s6e3ha2_unprepare(struct drm_panel *panel)
+{
+ struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
+ int ret;
+
+ ret = s6e3ha2_clear_error(ctx);
+ if (!ret)
+ ctx->bl_dev->props.power = FB_BLANK_POWERDOWN;
+
+ return s6e3ha2_power_off(ctx);
+}
+
+static int s6e3ha2_power_on(struct s6e3ha2 *ctx)
+{
+ int ret;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret < 0)
+ return ret;
+
+ msleep(120);
+
+ gpiod_set_value(ctx->enable_gpio, 0);
+ usleep_range(5000, 6000);
+ gpiod_set_value(ctx->enable_gpio, 1);
+
+ gpiod_set_value(ctx->reset_gpio, 1);
+ usleep_range(5000, 6000);
+ gpiod_set_value(ctx->reset_gpio, 0);
+ usleep_range(5000, 6000);
+
+ return 0;
+}
+static int s6e3ha2_prepare(struct drm_panel *panel)
+{
+ struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
+ int ret;
+
+ ret = s6e3ha2_power_on(ctx);
+ if (ret < 0)
+ return ret;
+
+ s6e3ha2_panel_init(ctx);
+
+ ret = s6e3ha2_clear_error(ctx);
+ if (ret < 0) {
+ s6e3ha2_power_off(ctx);
+ return ret;
+ }
+
+ ctx->bl_dev->props.power = FB_BLANK_NORMAL;
+
+ return 0;
+}
+
+static int s6e3ha2_enable(struct drm_panel *panel)
+{
+ struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ /* common setting */
+ mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+
+ s6e3ha2_test_key_on_f0(ctx);
+ s6e3ha2_test_key_on_fc(ctx);
+ s6e3ha2_touch_hsync_on1(ctx);
+ s6e3ha2_pentile_control(ctx);
+ s6e3ha2_poc_global(ctx);
+ s6e3ha2_poc_setting(ctx);
+ s6e3ha2_test_key_off_fc(ctx);
+
+ /* pcd setting off for TB */
+ s6e3ha2_pcd_set_off(ctx);
+ s6e3ha2_err_fg_set(ctx);
+ s6e3ha2_te_start_setting(ctx);
+
+ /* brightness setting */
+ s6e3ha2_set_brightness(ctx->bl_dev);
+ s6e3ha2_aor_control(ctx);
+ s6e3ha2_caps_elvss_set(ctx);
+ s6e3ha2_gamma_update(ctx);
+ s6e3ha2_acl_off(ctx);
+ s6e3ha2_acl_off_opr(ctx);
+ s6e3ha2_hbm_off(ctx);
+
+ /* elvss temp compensation */
+ s6e3ha2_test_global(ctx);
+ s6e3ha2_test(ctx);
+ s6e3ha2_test_key_off_f0(ctx);
+
+ mipi_dsi_dcs_set_display_on(dsi);
+ if (ctx->error != 0)
+ return ctx->error;
+
+ ctx->bl_dev->props.power = FB_BLANK_UNBLANK;
+
+ return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+ .clock = 14874,
+ .hdisplay = 1440,
+ .hsync_start = 1440 + 1,
+ .hsync_end = 1440 + 1 + 1,
+ .htotal = 1440 + 1 + 1 + 1,
+ .vdisplay = 2560,
+ .vsync_start = 2560 + 1,
+ .vsync_end = 2560 + 1 + 1,
+ .vtotal = 2560 + 1 + 1 + 15,
+ .vrefresh = 60,
+ .flags = 0,
+};
+
+static int s6e3ha2_get_modes(struct drm_panel *panel)
+{
+ struct drm_connector *connector = panel->connector;
+ struct drm_display_mode *mode;
+
+ mode = drm_mode_duplicate(panel->drm, &default_mode);
+ if (!mode) {
+ DRM_ERROR("failed to create a new display mode\n");
+ DRM_ERROR("failed to add mode %ux%ux@%u\n",
+ default_mode.hdisplay, default_mode.vdisplay,
+ default_mode.vrefresh);
+ return -ENOMEM;
+ }
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+ drm_mode_probed_add(connector, mode);
+
+ connector->display_info.width_mm = 71;
+ connector->display_info.height_mm = 125;
+
+ return 1;
+}
+
+static const struct drm_panel_funcs s6e3ha2_drm_funcs = {
+ .disable = s6e3ha2_disable,
+ .unprepare = s6e3ha2_unprepare,
+ .prepare = s6e3ha2_prepare,
+ .enable = s6e3ha2_enable,
+ .get_modes = s6e3ha2_get_modes,
+};
+
+static int s6e3ha2_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct s6e3ha2 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ ctx->dev = dev;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS;
+
+ ctx->supplies[0].supply = "vdd3";
+ ctx->supplies[1].supply = "vci";
+
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
+ ctx->supplies);
+ if (ret < 0) {
+ dev_err(dev, "failed to get regulators: %d\n", ret);
+ return ret;
+ }
+
+ ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio)) {
+ dev_err(dev, "cannot get reset-gpios %ld\n",
+ PTR_ERR(ctx->reset_gpio));
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH);
+ if (IS_ERR(ctx->enable_gpio)) {
+ dev_err(dev, "cannot get enable-gpios %ld\n",
+ PTR_ERR(ctx->enable_gpio));
+ return PTR_ERR(ctx->enable_gpio);
+ }
+
+ ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx,
+ &s6e3ha2_bl_ops, NULL);
+ if (IS_ERR(ctx->bl_dev)) {
+ dev_err(dev, "failed to register backlight device\n");
+ return PTR_ERR(ctx->bl_dev);
+ }
+
+ ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS;
+ ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS;
+ ctx->bl_dev->props.power = FB_BLANK_POWERDOWN;
+
+ drm_panel_init(&ctx->panel);
+ ctx->panel.dev = dev;
+ ctx->panel.funcs = &s6e3ha2_drm_funcs;
+
+ ret = drm_panel_add(&ctx->panel);
+ if (ret < 0)
+ goto unregister_backlight;
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0)
+ goto remove_panel;
+
+ return ret;
+
+remove_panel:
+ drm_panel_remove(&ctx->panel);
+
+unregister_backlight:
+ backlight_device_unregister(ctx->bl_dev);
+
+ return ret;
+}
+
+static int s6e3ha2_remove(struct mipi_dsi_device *dsi)
+{
+ struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi);
+
+ mipi_dsi_detach(dsi);
+ drm_panel_remove(&ctx->panel);
+ backlight_device_unregister(ctx->bl_dev);
+
+ return 0;
+}
+
+static const struct of_device_id s6e3ha2_of_match[] = {
+ { .compatible = "samsung,s6e3ha2" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, s6e3ha2_of_match);
+
+static struct mipi_dsi_driver s6e3ha2_driver = {
+ .probe = s6e3ha2_probe,
+ .remove = s6e3ha2_remove,
+ .driver = {
+ .name = "panel-samsung-s6e3ha2",
+ .of_match_table = s6e3ha2_of_match,
+ },
+};
+module_mipi_dsi_driver(s6e3ha2_driver);
+
+MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>");
+MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>");
+MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>");
+MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related
* [PATCH v4 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board
From: Hoegeun Kwon @ 2017-01-04 6:58 UTC (permalink / raw)
To: robh, thierry.reding, airlied, kgene, krzk, inki.dae
Cc: devicetree, linux-samsung-soc, linux-kernel, dri-devel,
jh80.chung, cw00.choi, Hyungwon Hwang, Hoegeun Kwon
In-Reply-To: <1483513115-3068-1-git-send-email-hoegeun.kwon@samsung.com>
From: Hyungwon Hwang <human.hwang@samsung.com>
This patch add the panel device tree node for S6E3HA2 display
controller to TM2 dts.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
---
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
index 5b9451d..b3ba1ac 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
@@ -304,11 +304,28 @@
reg = <1>;
dsi_out: endpoint {
+ remote-endpoint = <&panel_in>;
samsung,burst-clock-frequency = <512000000>;
samsung,esc-clock-frequency = <16000000>;
};
};
};
+
+ panel@0 {
+ compatible = "samsung,s6e3ha2";
+ reg = <0>;
+ vdd3-supply = <&ldo27_reg>;
+ vci-supply = <&ldo28_reg>;
+ reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+ te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
};
&hsi2c_0 {
--
1.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related
* [PATCH resend v4 2/3] ARM: dts: imx6: Support Savageboard dual
From: Milo Kim @ 2017-01-04 7:04 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, linux-kernel, linux-arm-kernel,
Milo Kim
Common savageboard DT file is used for board support.
Add the vendor name and specify the dtb file for i.MX6Q build.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
3 files changed, 53 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 16d3b5e7f5d1..552b63651ab9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -227,6 +227,7 @@ pine64 Pine64
pixcir PIXCIR MICROELECTRONICS Co., Ltd
plathome Plat'Home Co., Ltd.
plda PLDA
+poslab Poslab Technology Co., Ltd.
powervr PowerVR (deprecated, use img)
pulsedlight PulsedLight, Inc
qca Qualcomm Atheros, Inc.
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index cccdbcb557b6..fb7f904a5235 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -357,6 +357,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-sabreauto.dtb \
imx6dl-sabrelite.dtb \
imx6dl-sabresd.dtb \
+ imx6dl-savageboard.dtb \
imx6dl-ts4900.dtb \
imx6dl-tx6dl-comtft.dtb \
imx6dl-tx6s-8034.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-savageboard.dts b/arch/arm/boot/dts/imx6dl-savageboard.dts
new file mode 100644
index 000000000000..b95469c520a4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-savageboard.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright (C) 2017 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-savageboard.dtsi"
+
+/ {
+ model = "Poslab SavageBoard Dual";
+ compatible = "poslab,imx6dl-savageboard", "fsl,imx6dl";
+};
--
2.11.0
^ permalink raw reply related
* Re: [PATCH v4 2/3] ARM: dts: imx6: Support Savageboard dual
From: Milo Kim @ 2017-01-04 7:12 UTC (permalink / raw)
To: Shawn Guo, Sascha Hauer
Cc: Fabio Estevam, devicetree, linux-kernel, linux-arm-kernel
In-Reply-To: <20170104045553.26576-3-woogyom.kim@gmail.com>
On 01/04/2017 01:55 PM, Milo Kim wrote:
> Common savageboard DT file is used for board support.
> Add the vendor name and specify the dtb file for i.MX6Q build.
>
> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
> ---
> .../devicetree/bindings/vendor-prefixes.txt | 1 +
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6dl-savageboard.dts | 51 ++++++++++++++++++++++
> 3 files changed, 53 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-savageboard.dts
>
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
> index 16d3b5e7f5d1..88c33d827e51 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.txt
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
> @@ -227,6 +227,7 @@ pine64 Pine64
> pixcir PIXCIR MICROELECTRONICS Co., Ltd
> plathome Plat'Home Co., Ltd.
> plda PLDA
> +poslab Poslab Technology Co., Ltd.
I should input tab here instead of spaces, so updated single patch was
just sent. Please refer to the patch named "[PATCH resend v4 2/3] ARM:
dts: imx6: Support Savageboard dual".
Sorry for the inconvenience.
Best regards,
Milo
^ permalink raw reply
* Re: [PATCH v4 3/3] arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board
From: Chanwoo Choi @ 2017-01-04 7:16 UTC (permalink / raw)
To: Hoegeun Kwon, robh, thierry.reding, airlied, kgene, krzk,
inki.dae
Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, a.hajda,
jh80.chung, Hyungwon Hwang
In-Reply-To: <1483513115-3068-4-git-send-email-hoegeun.kwon@samsung.com>
Hi Hoegeun,
On 2017년 01월 04일 15:58, Hoegeun Kwon wrote:
> From: Hyungwon Hwang <human.hwang@samsung.com>
>
> This patch add the panel device tree node for S6E3HA2 display
> controller to TM2 dts.
>
> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
> ---
> arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> index 5b9451d..b3ba1ac 100644
> --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
> @@ -304,11 +304,28 @@
> reg = <1>;
>
> dsi_out: endpoint {
> + remote-endpoint = <&panel_in>;
> samsung,burst-clock-frequency = <512000000>;
> samsung,esc-clock-frequency = <16000000>;
> };
> };
> };
> +
> + panel@0 {
> + compatible = "samsung,s6e3ha2";
> + reg = <0>;
> + vdd3-supply = <&ldo27_reg>;
> + vci-supply = <&ldo28_reg>;
> + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
> + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
> + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> + };
> };
>
> &hsi2c_0 {
>
I tested this patch on Exynos5433-TM2 board.
It is well working to display the image to LCD panel.
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
--
Regards,
Chanwoo Choi
^ permalink raw reply
* Re: [PATCH v4 2/3] drm/panel: Add support for S6E3HA2 panel driver on TM2 board
From: Chanwoo Choi @ 2017-01-04 7:18 UTC (permalink / raw)
To: Hoegeun Kwon, robh, thierry.reding, airlied, kgene, krzk,
inki.dae
Cc: dri-devel, linux-kernel, devicetree, linux-samsung-soc, a.hajda,
jh80.chung, Donghwa Lee, Hyungwon Hwang
In-Reply-To: <1483513115-3068-3-git-send-email-hoegeun.kwon@samsung.com>
Hi Hoegeun,
I tested this patch on Exynos5433-TM2 board. It is well working
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Regards,
Chanwoo Choi
On 2017년 01월 04일 15:58, Hoegeun Kwon wrote:
> This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
> driver. This panel has 1440x2560 resolution in 5.7-inch physical
> panel in the TM2 device.
>
> Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
> Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
> ---
> .../bindings/display/panel/samsung,s6e3ha2.txt | 40 ++
> drivers/gpu/drm/panel/Kconfig | 6 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 741 +++++++++++++++++++++
> 4 files changed, 788 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
>
> diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> new file mode 100644
> index 0000000..6879f51
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> @@ -0,0 +1,40 @@
> +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
> +
> +Required properties:
> + - compatible: "samsung,s6e3ha2"
> + - reg: the virtual channel number of a DSI peripheral
> + - vdd3-supply: I/O voltage supply
> + - vci-supply: voltage supply for analog circuits
> + - reset-gpios: a GPIO spec for the reset pin (active low)
> + - enable-gpios: a GPIO spec for the panel enable pin (active high)
> + - te-gpios: a GPIO spec for the tearing effect synchronization signal
> + gpio pin (active high)
> +
> +The device node can contain one 'port' child node with one child
> +'endpoint' node, according to the bindings defined in [1]. This
> +node should describe panel's video bus.
> +
> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example:
> +
> +&dsi {
> + ...
> +
> + panel@0 {
> + compatible = "samsung,s6e3ha2";
> + reg = <0>;
> + vdd3-supply = <&ldo27_reg>;
> + vci-supply = <&ldo28_reg>;
> + reset-gpios = <&gpg0 0 GPIO_ACTIVE_LOW>;
> + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
> + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> + };
> +};
> +
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 62aba97..eea2902 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -52,6 +52,12 @@ config DRM_PANEL_PANASONIC_VVX10F034N00
> WUXGA (1920x1200) Novatek NT1397-based DSI panel as found in some
> Xperia Z2 tablets
>
> +config DRM_PANEL_SAMSUNG_S6E3HA2
> + tristate "Samsung S6E3HA2 DSI video mode panel"
> + depends on OF
> + depends on DRM_MIPI_DSI
> + select VIDEOMODE_HELPERS
> +
> config DRM_PANEL_SAMSUNG_S6E8AA0
> tristate "Samsung S6E8AA0 DSI video mode panel"
> depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index a5c7ec0..1d483b0 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
> obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
> obj-$(CONFIG_DRM_PANEL_PANASONIC_VVX10F034N00) += panel-panasonic-vvx10f034n00.o
> obj-$(CONFIG_DRM_PANEL_SAMSUNG_LD9040) += panel-samsung-ld9040.o
> +obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E3HA2) += panel-samsung-s6e3ha2.o
> obj-$(CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0) += panel-samsung-s6e8aa0.o
> obj-$(CONFIG_DRM_PANEL_SHARP_LQ101R1SX01) += panel-sharp-lq101r1sx01.o
> obj-$(CONFIG_DRM_PANEL_SHARP_LS043T1LE01) += panel-sharp-ls043t1le01.o
> diff --git a/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
> new file mode 100644
> index 0000000..8c5a1c2
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
> @@ -0,0 +1,741 @@
> +/*
> + * MIPI-DSI based s6e3ha2 AMOLED 5.7 inch panel driver.
> + *
> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
> + * Donghwa Lee <dh09.lee@samsung.com>
> + * Hyungwon Hwang <human.hwang@samsung.com>
> + * Hoegeun Kwon <hoegeun.kwon@samsung.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <drm/drmP.h>
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_panel.h>
> +#include <linux/backlight.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/regulator/consumer.h>
> +
> +#define S6E3HA2_MIN_BRIGHTNESS 0
> +#define S6E3HA2_MAX_BRIGHTNESS 100
> +#define S6E3HA2_DEFAULT_BRIGHTNESS 80
> +
> +#define S6E3HA2_NUM_GAMMA_STEPS 46
> +#define S6E3HA2_GAMMA_CMD_CNT 35
> +#define S6E3HA2_VINT_STATUS_MAX 10
> +
> +static const u8 gamma_tbl[S6E3HA2_NUM_GAMMA_STEPS][S6E3HA2_GAMMA_CMD_CNT] = {
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x82, 0x83,
> + 0x85, 0x88, 0x8b, 0x8b, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8c,
> + 0x94, 0x84, 0xb1, 0xaf, 0x8e, 0xcf, 0xad, 0xc9, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x84, 0x84,
> + 0x85, 0x87, 0x8b, 0x8a, 0x84, 0x88, 0x82, 0x82, 0x89, 0x86, 0x8a,
> + 0x93, 0x84, 0xb0, 0xae, 0x8e, 0xc9, 0xa8, 0xc5, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x88, 0x81, 0x84, 0x8a, 0x88, 0x8a,
> + 0x91, 0x84, 0xb1, 0xae, 0x8b, 0xd5, 0xb2, 0xcc, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x8a, 0x8a, 0x84, 0x87, 0x81, 0x84, 0x8a, 0x87, 0x8a,
> + 0x91, 0x85, 0xae, 0xac, 0x8a, 0xc3, 0xa3, 0xc0, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x85, 0x85,
> + 0x86, 0x85, 0x88, 0x89, 0x84, 0x89, 0x82, 0x84, 0x87, 0x85, 0x8b,
> + 0x91, 0x88, 0xad, 0xab, 0x8a, 0xb7, 0x9b, 0xb6, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x89, 0x8a, 0x84, 0x89, 0x83, 0x83, 0x86, 0x84, 0x8b,
> + 0x90, 0x84, 0xb0, 0xae, 0x8b, 0xce, 0xad, 0xc8, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x89,
> + 0x8f, 0x84, 0xac, 0xaa, 0x89, 0xb1, 0x98, 0xaf, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x88, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8c,
> + 0x91, 0x86, 0xac, 0xaa, 0x89, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x85, 0x87, 0x89, 0x8a, 0x83, 0x87, 0x82, 0x85, 0x88, 0x87, 0x88,
> + 0x8b, 0x82, 0xad, 0xaa, 0x8a, 0xc2, 0xa5, 0xbd, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x89, 0x87, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x82, 0x85, 0x84, 0x8a,
> + 0x8e, 0x84, 0xae, 0xac, 0x89, 0xda, 0xb7, 0xd0, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x85, 0x86, 0x87, 0x89, 0x84, 0x88, 0x83, 0x80, 0x83, 0x82, 0x8b,
> + 0x8e, 0x85, 0xac, 0xaa, 0x89, 0xc8, 0xaa, 0xc1, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x85, 0x86, 0x87, 0x89, 0x81, 0x85, 0x81, 0x84, 0x86, 0x84, 0x8c,
> + 0x8c, 0x84, 0xa9, 0xa8, 0x87, 0xa3, 0x92, 0xa1, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x85, 0x86, 0x87, 0x89, 0x84, 0x86, 0x83, 0x80, 0x83, 0x81, 0x8c,
> + 0x8d, 0x84, 0xaa, 0xaa, 0x89, 0xce, 0xaf, 0xc5, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x85, 0x86, 0x87, 0x89, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c,
> + 0x8c, 0x84, 0xa8, 0xa8, 0x88, 0xb5, 0x9f, 0xb0, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x83, 0x85, 0x85, 0x8c,
> + 0x8b, 0x84, 0xab, 0xa8, 0x86, 0xd4, 0xb4, 0xc9, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x86, 0x86, 0x87, 0x88, 0x81, 0x83, 0x80, 0x84, 0x84, 0x85, 0x8b,
> + 0x8a, 0x83, 0xa6, 0xa5, 0x84, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x84, 0x84,
> + 0x86, 0x85, 0x86, 0x86, 0x82, 0x85, 0x81, 0x82, 0x83, 0x84, 0x8e,
> + 0x8b, 0x83, 0xa4, 0xa3, 0x8a, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8e,
> + 0x8b, 0x83, 0xa4, 0xa2, 0x86, 0xc1, 0xa9, 0xb7, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x82, 0x82, 0x84, 0x8d,
> + 0x89, 0x82, 0xa2, 0xa1, 0x84, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xb8, 0x00, 0xc3, 0x00, 0xb1, 0x88, 0x86, 0x87, 0x83, 0x83,
> + 0x85, 0x86, 0x87, 0x87, 0x82, 0x85, 0x81, 0x83, 0x83, 0x85, 0x8c,
> + 0x87, 0x7f, 0xa2, 0x9d, 0x88, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xbb, 0x00, 0xc5, 0x00, 0xb4, 0x87, 0x86, 0x86, 0x84, 0x83,
> + 0x86, 0x87, 0x87, 0x87, 0x80, 0x82, 0x7f, 0x86, 0x86, 0x88, 0x8a,
> + 0x84, 0x7e, 0x9d, 0x9c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xbd, 0x00, 0xc7, 0x00, 0xb7, 0x87, 0x85, 0x85, 0x84, 0x83,
> + 0x86, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x83, 0x84, 0x85, 0x8a,
> + 0x85, 0x7e, 0x9c, 0x9b, 0x85, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xc0, 0x00, 0xca, 0x00, 0xbb, 0x87, 0x86, 0x85, 0x83, 0x83,
> + 0x85, 0x86, 0x86, 0x88, 0x81, 0x83, 0x80, 0x84, 0x85, 0x86, 0x89,
> + 0x83, 0x7d, 0x9c, 0x99, 0x87, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xc4, 0x00, 0xcd, 0x00, 0xbe, 0x87, 0x86, 0x85, 0x83, 0x83,
> + 0x86, 0x85, 0x85, 0x87, 0x81, 0x82, 0x80, 0x82, 0x82, 0x83, 0x8a,
> + 0x85, 0x7f, 0x9f, 0x9b, 0x86, 0xb4, 0xa1, 0xac, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xc7, 0x00, 0xd0, 0x00, 0xc2, 0x87, 0x85, 0x85, 0x83, 0x82,
> + 0x85, 0x85, 0x85, 0x86, 0x82, 0x83, 0x80, 0x82, 0x82, 0x84, 0x87,
> + 0x86, 0x80, 0x9e, 0x9a, 0x87, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xca, 0x00, 0xd2, 0x00, 0xc5, 0x87, 0x85, 0x84, 0x82, 0x82,
> + 0x84, 0x85, 0x85, 0x86, 0x81, 0x82, 0x7f, 0x82, 0x82, 0x84, 0x88,
> + 0x86, 0x81, 0x9d, 0x98, 0x86, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xce, 0x00, 0xd6, 0x00, 0xca, 0x86, 0x85, 0x84, 0x83, 0x83,
> + 0x85, 0x84, 0x84, 0x85, 0x81, 0x82, 0x80, 0x81, 0x81, 0x82, 0x89,
> + 0x86, 0x81, 0x9c, 0x97, 0x86, 0xa7, 0x98, 0xa1, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xd1, 0x00, 0xd9, 0x00, 0xce, 0x86, 0x84, 0x83, 0x83, 0x82,
> + 0x85, 0x85, 0x85, 0x86, 0x81, 0x83, 0x81, 0x82, 0x82, 0x83, 0x86,
> + 0x83, 0x7f, 0x99, 0x95, 0x86, 0xbb, 0xa4, 0xb3, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xd4, 0x00, 0xdb, 0x00, 0xd1, 0x86, 0x85, 0x83, 0x83, 0x82,
> + 0x85, 0x84, 0x84, 0x85, 0x80, 0x83, 0x82, 0x80, 0x80, 0x81, 0x87,
> + 0x84, 0x81, 0x98, 0x93, 0x85, 0xae, 0x9c, 0xa8, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xd8, 0x00, 0xde, 0x00, 0xd6, 0x86, 0x84, 0x83, 0x81, 0x81,
> + 0x83, 0x85, 0x85, 0x85, 0x82, 0x83, 0x81, 0x81, 0x81, 0x83, 0x86,
> + 0x84, 0x80, 0x98, 0x91, 0x85, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xdc, 0x00, 0xe2, 0x00, 0xda, 0x85, 0x84, 0x83, 0x82, 0x82,
> + 0x84, 0x84, 0x84, 0x85, 0x81, 0x82, 0x82, 0x80, 0x80, 0x81, 0x83,
> + 0x82, 0x7f, 0x99, 0x93, 0x86, 0x94, 0x8b, 0x92, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xdf, 0x00, 0xe5, 0x00, 0xde, 0x85, 0x84, 0x82, 0x82, 0x82,
> + 0x84, 0x83, 0x83, 0x84, 0x81, 0x81, 0x80, 0x83, 0x82, 0x84, 0x82,
> + 0x81, 0x7f, 0x99, 0x92, 0x86, 0x7b, 0x7b, 0x7c, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x83, 0x83, 0x84, 0x80,
> + 0x81, 0x7c, 0x99, 0x92, 0x87, 0xa1, 0x93, 0x9d, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x85, 0x84, 0x83, 0x81, 0x81,
> + 0x82, 0x82, 0x82, 0x83, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83,
> + 0x82, 0x80, 0x91, 0x8d, 0x83, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x83, 0x83, 0x84, 0x80, 0x81, 0x80, 0x81, 0x80, 0x82, 0x83,
> + 0x81, 0x7f, 0x91, 0x8c, 0x82, 0x8d, 0x88, 0x8b, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x82,
> + 0x82, 0x7f, 0x94, 0x89, 0x84, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x83, 0x83, 0x83, 0x82, 0x82, 0x81, 0x81, 0x80, 0x82, 0x83,
> + 0x82, 0x7f, 0x91, 0x85, 0x81, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x83, 0x82, 0x84, 0x83,
> + 0x82, 0x7f, 0x90, 0x84, 0x81, 0x9a, 0x90, 0x96, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe4, 0x00, 0xe9, 0x00, 0xe3, 0x84, 0x83, 0x82, 0x80, 0x80,
> + 0x82, 0x83, 0x83, 0x83, 0x80, 0x80, 0x7f, 0x80, 0x80, 0x81, 0x81,
> + 0x82, 0x83, 0x7e, 0x80, 0x7c, 0xa4, 0x97, 0x9f, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xe9, 0x00, 0xec, 0x00, 0xe8, 0x84, 0x83, 0x82, 0x81, 0x81,
> + 0x82, 0x82, 0x82, 0x83, 0x7f, 0x7f, 0x7f, 0x81, 0x80, 0x82, 0x83,
> + 0x83, 0x84, 0x79, 0x7c, 0x79, 0xb1, 0xa0, 0xaa, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xed, 0x00, 0xf0, 0x00, 0xec, 0x83, 0x83, 0x82, 0x80, 0x80,
> + 0x81, 0x82, 0x82, 0x82, 0x7f, 0x7f, 0x7e, 0x81, 0x81, 0x82, 0x80,
> + 0x81, 0x81, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xf1, 0x00, 0xf4, 0x00, 0xf1, 0x83, 0x82, 0x82, 0x80, 0x80,
> + 0x81, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x81, 0x7d,
> + 0x7e, 0x7f, 0x84, 0x84, 0x83, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xf6, 0x00, 0xf7, 0x00, 0xf5, 0x82, 0x82, 0x81, 0x80, 0x80,
> + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x7f, 0x7f, 0x7f, 0x82,
> + 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x00, 0xfa, 0x00, 0xfb, 0x00, 0xfa, 0x81, 0x81, 0x81, 0x80, 0x80,
> + 0x80, 0x82, 0x82, 0x82, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
> + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80,
> + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
> + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 },
> + { 0x01, 0x00, 0x01, 0x00, 0x01, 0x00, 0x80, 0x80, 0x80, 0x80, 0x80,
> + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80,
> + 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00,
> + 0x00, 0x00 }
> +};
> +
> +unsigned char vint_table[S6E3HA2_VINT_STATUS_MAX] = {
> + 0x18, 0x19, 0x1a, 0x1b, 0x1c,
> + 0x1d, 0x1e, 0x1f, 0x20, 0x21
> +};
> +
> +struct s6e3ha2 {
> + struct device *dev;
> + struct drm_panel panel;
> + struct backlight_device *bl_dev;
> +
> + struct regulator_bulk_data supplies[2];
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *enable_gpio;
> +
> + /* This field is tested by functions directly accessing DSI bus before
> + * transfer, transfer is skipped if it is set. In case of transfer
> + * failure or unexpected response the field is set to error value.
> + * Such construct allows to eliminate many checks in higher level
> + * functions.
> + */
> + int error;
> +};
> +
> +static int s6e3ha2_clear_error(struct s6e3ha2 *ctx)
> +{
> + int ret = ctx->error;
> +
> + ctx->error = 0;
> + return ret;
> +}
> +
> +static void s6e3ha2_dcs_write(struct s6e3ha2 *ctx, const void *data, size_t len)
> +{
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> + ssize_t ret;
> +
> + if (ctx->error < 0)
> + return;
> +
> + ret = mipi_dsi_dcs_write_buffer(dsi, data, len);
> + if (ret < 0) {
> + dev_err(ctx->dev, "error %zd writing dcs seq: %*ph\n",
> + ret, (int)len, data);
> + ctx->error = ret;
> + }
> +}
> +
> +#define s6e3ha2_dcs_write_seq_static(ctx, seq...) do { \
> + static const u8 d[] = { seq }; \
> + s6e3ha2_dcs_write(ctx, d, ARRAY_SIZE(d)); \
> +} while (0)
> +
> +static void s6e3ha2_test_key_on_f0(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0x5a, 0x5a);
> +}
> +
> +static void s6e3ha2_test_key_off_f0(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf0, 0xa5, 0xa5);
> +}
> +
> +static void s6e3ha2_test_key_on_fc(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0x5a, 0x5a);
> +}
> +
> +static void s6e3ha2_test_key_off_fc(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfc, 0xa5, 0xa5);
> +}
> +
> +static void s6e3ha2_single_dsi_set(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf2, 0x67);
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf9, 0x09);
> +}
> +
> +static void s6e3ha2_freq_calibration(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfd, 0x1c);
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20, 0x39);
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0xa0);
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x20);
> + s6e3ha2_dcs_write_seq_static(ctx, 0xce, 0x03, 0x3b, 0x12, 0x62,
> + 0x40, 0x80, 0xc0, 0x28, 0x28, 0x28, 0x28, 0x39, 0xc5);
> +}
> +
> +static void s6e3ha2_aor_control(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb2, 0x03, 0x10);
> +}
> +
> +static void s6e3ha2_caps_elvss_set(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb6, 0x9c, 0x0a);
> +}
> +
> +static void s6e3ha2_acl_off(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0x55, 0x00);
> +}
> +
> +static void s6e3ha2_acl_off_opr(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb5, 0x40);
> +}
> +
> +static void s6e3ha2_test_global(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x07);
> +}
> +
> +static void s6e3ha2_test(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb8, 0x19);
> +}
> +
> +static void s6e3ha2_touch_hsync_on1(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx,
> + 0xbd, 0x33, 0x11, 0x02, 0x16, 0x02, 0x16);
> +}
> +
> +static void s6e3ha2_pentile_control(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xc0, 0x00, 0x00, 0xd8, 0xd8);
> +}
> +
> +static void s6e3ha2_poc_global(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb0, 0x20);
> +}
> +
> +static void s6e3ha2_poc_setting(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xfe, 0x08);
> +}
> +
> +static void s6e3ha2_pcd_set_off(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xcc, 0x40, 0x51);
> +}
> +
> +static void s6e3ha2_err_fg_set(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xed, 0x44);
> +}
> +
> +static void s6e3ha2_hbm_off(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0x53, 0x00);
> +}
> +
> +static void s6e3ha2_te_start_setting(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xb9, 0x10, 0x09, 0xff, 0x00, 0x09);
> +}
> +
> +static void s6e3ha2_gamma_update(struct s6e3ha2 *ctx)
> +{
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x03);
> + ndelay(100); /* need for 100ns delay */
> + s6e3ha2_dcs_write_seq_static(ctx, 0xf7, 0x00);
> +}
> +
> +static int s6e3ha2_get_brightness(struct backlight_device *bl_dev)
> +{
> + return bl_dev->props.brightness;
> +}
> +
> +static void s6e3ha2_set_vint(struct s6e3ha2 *ctx)
> +{
> + struct backlight_device *bl_dev = ctx->bl_dev;
> + unsigned int brightness = bl_dev->props.brightness;
> + unsigned char data[] = { 0xf4, 0x8b,
> + vint_table[brightness * (S6E3HA2_VINT_STATUS_MAX - 1) /
> + S6E3HA2_MAX_BRIGHTNESS] };
> +
> + s6e3ha2_dcs_write(ctx, data, 3);
> +}
> +
> +static unsigned int s6e3ha2_get_brightness_index(unsigned int brightness)
> +{
> + return (brightness * (S6E3HA2_NUM_GAMMA_STEPS - 1)) /
> + S6E3HA2_MAX_BRIGHTNESS;
> +}
> +
> +static int s6e3ha2_update_gamma(struct s6e3ha2 *ctx, unsigned int brightness)
> +{
> + struct backlight_device *bl_dev = ctx->bl_dev;
> + unsigned int index = s6e3ha2_get_brightness_index(brightness);
> + u8 data[S6E3HA2_GAMMA_CMD_CNT + 1] = { 0xca, };
> +
> + memcpy(data + 1, gamma_tbl + index, S6E3HA2_GAMMA_CMD_CNT);
> + s6e3ha2_dcs_write(ctx, data, ARRAY_SIZE(data));
> +
> + s6e3ha2_gamma_update(ctx);
> + bl_dev->props.brightness = brightness;
> +
> + return 0;
> +}
> +
> +static int s6e3ha2_set_brightness(struct backlight_device *bl_dev)
> +{
> + struct s6e3ha2 *ctx = (struct s6e3ha2 *)bl_get_data(bl_dev);
> + unsigned int brightness = bl_dev->props.brightness;
> +
> + if (brightness < S6E3HA2_MIN_BRIGHTNESS ||
> + brightness > bl_dev->props.max_brightness) {
> + dev_err(ctx->dev, "Invalid brightness: %u\n", brightness);
> + return -EINVAL;
> + }
> +
> + if (bl_dev->props.power > FB_BLANK_NORMAL)
> + return -EPERM;
> +
> + s6e3ha2_test_key_on_f0(ctx);
> + s6e3ha2_update_gamma(ctx, brightness);
> + s6e3ha2_aor_control(ctx);
> + s6e3ha2_set_vint(ctx);
> + s6e3ha2_test_key_off_f0(ctx);
> +
> + return ctx->error;
> +}
> +
> +static const struct backlight_ops s6e3ha2_bl_ops = {
> + .get_brightness = s6e3ha2_get_brightness,
> + .update_status = s6e3ha2_set_brightness,
> +};
> +
> +static void s6e3ha2_panel_init(struct s6e3ha2 *ctx)
> +{
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +
> + mipi_dsi_dcs_exit_sleep_mode(dsi);
> + usleep_range(5000, 6000);
> +
> + s6e3ha2_test_key_on_f0(ctx);
> + s6e3ha2_single_dsi_set(ctx);
> + s6e3ha2_test_key_on_fc(ctx);
> + s6e3ha2_freq_calibration(ctx);
> + s6e3ha2_test_key_off_fc(ctx);
> + s6e3ha2_test_key_off_f0(ctx);
> +}
> +
> +static int s6e3ha2_power_off(struct s6e3ha2 *ctx)
> +{
> + return regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> +}
> +
> +static int s6e3ha2_disable(struct drm_panel *panel)
> +{
> + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +
> + mipi_dsi_dcs_enter_sleep_mode(dsi);
> + if (ctx->error != 0)
> + goto err;
> +
> + mipi_dsi_dcs_set_display_off(dsi);
> + if (ctx->error != 0)
> + goto err;
> +
> + msleep(40);
> + ctx->bl_dev->props.power = FB_BLANK_NORMAL;
> +
> + return 0;
> +err:
> + return ctx->error;
> +}
> +
> +static int s6e3ha2_unprepare(struct drm_panel *panel)
> +{
> + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
> + int ret;
> +
> + ret = s6e3ha2_clear_error(ctx);
> + if (!ret)
> + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN;
> +
> + return s6e3ha2_power_off(ctx);
> +}
> +
> +static int s6e3ha2_power_on(struct s6e3ha2 *ctx)
> +{
> + int ret;
> +
> + ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
> + if (ret < 0)
> + return ret;
> +
> + msleep(120);
> +
> + gpiod_set_value(ctx->enable_gpio, 0);
> + usleep_range(5000, 6000);
> + gpiod_set_value(ctx->enable_gpio, 1);
> +
> + gpiod_set_value(ctx->reset_gpio, 1);
> + usleep_range(5000, 6000);
> + gpiod_set_value(ctx->reset_gpio, 0);
> + usleep_range(5000, 6000);
> +
> + return 0;
> +}
> +static int s6e3ha2_prepare(struct drm_panel *panel)
> +{
> + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
> + int ret;
> +
> + ret = s6e3ha2_power_on(ctx);
> + if (ret < 0)
> + return ret;
> +
> + s6e3ha2_panel_init(ctx);
> +
> + ret = s6e3ha2_clear_error(ctx);
> + if (ret < 0) {
> + s6e3ha2_power_off(ctx);
> + return ret;
> + }
> +
> + ctx->bl_dev->props.power = FB_BLANK_NORMAL;
> +
> + return 0;
> +}
> +
> +static int s6e3ha2_enable(struct drm_panel *panel)
> +{
> + struct s6e3ha2 *ctx = container_of(panel, struct s6e3ha2, panel);
> + struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
> +
> + /* common setting */
> + mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
> +
> + s6e3ha2_test_key_on_f0(ctx);
> + s6e3ha2_test_key_on_fc(ctx);
> + s6e3ha2_touch_hsync_on1(ctx);
> + s6e3ha2_pentile_control(ctx);
> + s6e3ha2_poc_global(ctx);
> + s6e3ha2_poc_setting(ctx);
> + s6e3ha2_test_key_off_fc(ctx);
> +
> + /* pcd setting off for TB */
> + s6e3ha2_pcd_set_off(ctx);
> + s6e3ha2_err_fg_set(ctx);
> + s6e3ha2_te_start_setting(ctx);
> +
> + /* brightness setting */
> + s6e3ha2_set_brightness(ctx->bl_dev);
> + s6e3ha2_aor_control(ctx);
> + s6e3ha2_caps_elvss_set(ctx);
> + s6e3ha2_gamma_update(ctx);
> + s6e3ha2_acl_off(ctx);
> + s6e3ha2_acl_off_opr(ctx);
> + s6e3ha2_hbm_off(ctx);
> +
> + /* elvss temp compensation */
> + s6e3ha2_test_global(ctx);
> + s6e3ha2_test(ctx);
> + s6e3ha2_test_key_off_f0(ctx);
> +
> + mipi_dsi_dcs_set_display_on(dsi);
> + if (ctx->error != 0)
> + return ctx->error;
> +
> + ctx->bl_dev->props.power = FB_BLANK_UNBLANK;
> +
> + return 0;
> +}
> +
> +static const struct drm_display_mode default_mode = {
> + .clock = 14874,
> + .hdisplay = 1440,
> + .hsync_start = 1440 + 1,
> + .hsync_end = 1440 + 1 + 1,
> + .htotal = 1440 + 1 + 1 + 1,
> + .vdisplay = 2560,
> + .vsync_start = 2560 + 1,
> + .vsync_end = 2560 + 1 + 1,
> + .vtotal = 2560 + 1 + 1 + 15,
> + .vrefresh = 60,
> + .flags = 0,
> +};
> +
> +static int s6e3ha2_get_modes(struct drm_panel *panel)
> +{
> + struct drm_connector *connector = panel->connector;
> + struct drm_display_mode *mode;
> +
> + mode = drm_mode_duplicate(panel->drm, &default_mode);
> + if (!mode) {
> + DRM_ERROR("failed to create a new display mode\n");
> + DRM_ERROR("failed to add mode %ux%ux@%u\n",
> + default_mode.hdisplay, default_mode.vdisplay,
> + default_mode.vrefresh);
> + return -ENOMEM;
> + }
> +
> + drm_mode_set_name(mode);
> +
> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> + drm_mode_probed_add(connector, mode);
> +
> + connector->display_info.width_mm = 71;
> + connector->display_info.height_mm = 125;
> +
> + return 1;
> +}
> +
> +static const struct drm_panel_funcs s6e3ha2_drm_funcs = {
> + .disable = s6e3ha2_disable,
> + .unprepare = s6e3ha2_unprepare,
> + .prepare = s6e3ha2_prepare,
> + .enable = s6e3ha2_enable,
> + .get_modes = s6e3ha2_get_modes,
> +};
> +
> +static int s6e3ha2_probe(struct mipi_dsi_device *dsi)
> +{
> + struct device *dev = &dsi->dev;
> + struct s6e3ha2 *ctx;
> + int ret;
> +
> + ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
> + if (!ctx)
> + return -ENOMEM;
> +
> + mipi_dsi_set_drvdata(dsi, ctx);
> +
> + ctx->dev = dev;
> +
> + dsi->lanes = 4;
> + dsi->format = MIPI_DSI_FMT_RGB888;
> + dsi->mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS;
> +
> + ctx->supplies[0].supply = "vdd3";
> + ctx->supplies[1].supply = "vci";
> +
> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ctx->supplies),
> + ctx->supplies);
> + if (ret < 0) {
> + dev_err(dev, "failed to get regulators: %d\n", ret);
> + return ret;
> + }
> +
> + ctx->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> + if (IS_ERR(ctx->reset_gpio)) {
> + dev_err(dev, "cannot get reset-gpios %ld\n",
> + PTR_ERR(ctx->reset_gpio));
> + return PTR_ERR(ctx->reset_gpio);
> + }
> +
> + ctx->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH);
> + if (IS_ERR(ctx->enable_gpio)) {
> + dev_err(dev, "cannot get enable-gpios %ld\n",
> + PTR_ERR(ctx->enable_gpio));
> + return PTR_ERR(ctx->enable_gpio);
> + }
> +
> + ctx->bl_dev = backlight_device_register("s6e3ha2", dev, ctx,
> + &s6e3ha2_bl_ops, NULL);
> + if (IS_ERR(ctx->bl_dev)) {
> + dev_err(dev, "failed to register backlight device\n");
> + return PTR_ERR(ctx->bl_dev);
> + }
> +
> + ctx->bl_dev->props.max_brightness = S6E3HA2_MAX_BRIGHTNESS;
> + ctx->bl_dev->props.brightness = S6E3HA2_DEFAULT_BRIGHTNESS;
> + ctx->bl_dev->props.power = FB_BLANK_POWERDOWN;
> +
> + drm_panel_init(&ctx->panel);
> + ctx->panel.dev = dev;
> + ctx->panel.funcs = &s6e3ha2_drm_funcs;
> +
> + ret = drm_panel_add(&ctx->panel);
> + if (ret < 0)
> + goto unregister_backlight;
> +
> + ret = mipi_dsi_attach(dsi);
> + if (ret < 0)
> + goto remove_panel;
> +
> + return ret;
> +
> +remove_panel:
> + drm_panel_remove(&ctx->panel);
> +
> +unregister_backlight:
> + backlight_device_unregister(ctx->bl_dev);
> +
> + return ret;
> +}
> +
> +static int s6e3ha2_remove(struct mipi_dsi_device *dsi)
> +{
> + struct s6e3ha2 *ctx = mipi_dsi_get_drvdata(dsi);
> +
> + mipi_dsi_detach(dsi);
> + drm_panel_remove(&ctx->panel);
> + backlight_device_unregister(ctx->bl_dev);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id s6e3ha2_of_match[] = {
> + { .compatible = "samsung,s6e3ha2" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, s6e3ha2_of_match);
> +
> +static struct mipi_dsi_driver s6e3ha2_driver = {
> + .probe = s6e3ha2_probe,
> + .remove = s6e3ha2_remove,
> + .driver = {
> + .name = "panel-samsung-s6e3ha2",
> + .of_match_table = s6e3ha2_of_match,
> + },
> +};
> +module_mipi_dsi_driver(s6e3ha2_driver);
> +
> +MODULE_AUTHOR("Donghwa Lee <dh09.lee@samsung.com>");
> +MODULE_AUTHOR("Hyungwon Hwang <human.hwang@samsung.com>");
> +MODULE_AUTHOR("Hoegeun Kwon <hoegeun.kwon@samsung.com>");
> +MODULE_DESCRIPTION("MIPI-DSI based s6e3ha2 AMOLED Panel Driver");
> +MODULE_LICENSE("GPL v2");
>
^ permalink raw reply
* Re: [PATCH v4 1/3] drm/exynos: mic: Add mode_set callback function
From: Inki Dae @ 2017-01-04 7:29 UTC (permalink / raw)
To: Hoegeun Kwon, robh, thierry.reding, airlied, kgene, krzk
Cc: devicetree, linux-samsung-soc, linux-kernel, dri-devel,
jh80.chung, cw00.choi
In-Reply-To: <1483513115-3068-2-git-send-email-hoegeun.kwon@samsung.com>
2017년 01월 04일 15:58에 Hoegeun Kwon 이(가) 쓴 글:
> Before applying the patch, used the of_get_videomode function to
> parse the display-timings in the panel which is the child driver
> of dsi in the devicetree. this is wrong. So removed the
> of_get_videomode and fixed to get videomode struct through
> mode_set callback function.
>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
> ---
> drivers/gpu/drm/exynos/exynos_drm_mic.c | 33 ++++++++++++++++++++++-----------
> 1 file changed, 22 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/gpu/drm/exynos/exynos_drm_mic.c b/drivers/gpu/drm/exynos/exynos_drm_mic.c
> index a0def0b..9a50ceb 100644
> --- a/drivers/gpu/drm/exynos/exynos_drm_mic.c
> +++ b/drivers/gpu/drm/exynos/exynos_drm_mic.c
> @@ -286,13 +286,6 @@ static int parse_dt(struct exynos_mic *mic)
> }
> nodes[j++] = remote_node;
>
> - ret = of_get_videomode(remote_node,
> - &mic->vm, 0);
> - if (ret) {
> - DRM_ERROR("mic: failed to get videomode");
> - goto exit;
> - }
> -
> break;
> default:
> DRM_ERROR("mic: Unknown endpoint from MIC");
> @@ -329,6 +322,27 @@ static void mic_post_disable(struct drm_bridge *bridge)
> mutex_unlock(&mic_mutex);
> }
>
> +static void mic_mode_set(struct drm_bridge *bridge,
> + struct drm_display_mode *mode,
> + struct drm_display_mode *adjusted_mode)
> +{
> + struct exynos_mic *mic = bridge->driver_private;
> +
> + mutex_lock(&mic_mutex);
> + if (mic->enabled)
> + goto already_enabled;
mode setting should be performed every time mode_set callback is called so remove above two lines.
> +
> + drm_display_mode_to_videomode(mode, &mic->vm);
> +
> + if (!mic->i80_mode)
> + mic_set_porch_timing(mic);
> + mic_set_img_size(mic);
> + mic_set_output_timing(mic);
> +
> +already_enabled:
So this label is unnecessary.
> + mutex_unlock(&mic_mutex);
> +}
> +
> static void mic_pre_enable(struct drm_bridge *bridge)
> {
> struct exynos_mic *mic = bridge->driver_private;
> @@ -355,10 +369,6 @@ static void mic_pre_enable(struct drm_bridge *bridge)
> goto turn_off_clks;
> }
>
> - if (!mic->i80_mode)
> - mic_set_porch_timing(mic);
> - mic_set_img_size(mic);
> - mic_set_output_timing(mic);
> mic_set_reg_on(mic, 1);
> mic->enabled = 1;
> mutex_unlock(&mic_mutex);
> @@ -377,6 +387,7 @@ static void mic_enable(struct drm_bridge *bridge) { }
> static const struct drm_bridge_funcs mic_bridge_funcs = {
> .disable = mic_disable,
> .post_disable = mic_post_disable,
> + .mode_set = mic_mode_set,
> .pre_enable = mic_pre_enable,
> .enable = mic_enable,
> };
>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply
* [RFC 1/4] Documentation: devicetree: add multiple cpu port DSA binding
From: John Crispin @ 2017-01-04 7:38 UTC (permalink / raw)
To: Andrew Lunn, David S. Miller, Florian Fainelli, Vivien Didelot
Cc: netdev, Rob Herring, devicetree
In-Reply-To: <1483515484-21793-1-git-send-email-john@phrozen.org>
From: Andrew Lunn <andrew@lunn.ch>
Extend the DSA binding documentation, adding the new properties required
when there is more than one CPU port attached to the switch.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
Documentation/devicetree/bindings/net/dsa/dsa.txt | 67 ++++++++++++++++++++-
1 file changed, 66 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt
index a4a570f..fc901cf 100644
--- a/Documentation/devicetree/bindings/net/dsa/dsa.txt
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt
@@ -337,13 +337,25 @@ Optional property:
This mii-bus will be used in preference to the
global dsa,mii-bus defined above, for this switch.
+- ethernet : Optional for "cpu" ports. A phandle to an ethernet
+ device which will be used by this CPU port for
+ passing packets to/from the host. If not present,
+ the port will use the "dsa,ethernet" property
+ defined above.
+
+- cpu : Option for non "cpu"/"dsa" ports. A phandle to a
+ "cpu" port, which will be used for passing packets
+ from this port to the host. If not present, the first
+ "cpu" port will be used.
+
+
Optional subnodes:
- fixed-link : Fixed-link subnode describing a link to a non-MDIO
managed entity. See
Documentation/devicetree/bindings/net/fixed-link.txt
for details.
-Example:
+Examples:
dsa@0 {
compatible = "marvell,dsa";
@@ -416,3 +428,56 @@ Example:
};
};
};
+
+ dsa@1 {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ dsa,ethernet = <ð0port>;
+ dsa,mii-bus = <&mdio>;
+
+ switch@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0 0>; /* MDIO address 0, switch 0 in tree */
+
+ port@0 {
+ reg = <0>;
+ label = "lan4";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan3";
+ cpu = <&cpu1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan1";
+ cpu = <&cpu1>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+
+ cpu1: port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <ð1port>;
+ };
+ };
+ };
--
1.7.10.4
^ permalink raw reply related
* [PATCH v5 0/3] Add support for the S6E3HA2 panel on TM2 board
From: Hoegeun Kwon @ 2017-01-04 8:15 UTC (permalink / raw)
To: robh, thierry.reding, airlied, kgene, krzk, inki.dae
Cc: devicetree, linux-samsung-soc, linux-kernel, dri-devel,
jh80.chung, cw00.choi, Hoegeun Kwon
In-Reply-To: <CGME20170104081520epcas1p42dd46f1d13adfde20a2559bd5c1cbd3d@epcas1p4.samsung.com>
Purpose of this patch is add support for S6E3HA2 AMOLED panel on
the TM2 board. The first patch adds support for S6E3HA2 panel
device tree document and driver, the second patch add support for
S6E3HA2 panel device tree.
Change for V5:
- The V5 has only one fix in V4 below.
- Removed the enable check of the mic driver in mode_set
callback, because mode_set should be performed every time.
Changes for V4:
- Removed display-timings in devicetree, the display-timings has
been fixed to be provided by the device driver.
- Added the mode_set callback function into exynos_drm_mic,
because the exynos_drm_mic driver can not parse a videomode
struct by removing the display-timings from the devicetree.
Hoegeun Kwon (2):
drm/exynos: mic: Add mode_set callback function
drm/panel: Add support for S6E3HA2 panel driver on TM2 board
Hyungwon Hwang (1):
arm64: dts: exynos: Add support for S6E3HA2 panel device on TM2 board
.../bindings/display/panel/samsung,s6e3ha2.txt | 40 ++
arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 17 +
drivers/gpu/drm/exynos/exynos_drm_mic.c | 30 +-
drivers/gpu/drm/panel/Kconfig | 6 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 741 +++++++++++++++++++++
6 files changed, 824 insertions(+), 11 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
--
1.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply
* [PATCH v5 1/3] drm/exynos: mic: Add mode_set callback function
From: Hoegeun Kwon @ 2017-01-04 8:15 UTC (permalink / raw)
To: robh, thierry.reding, airlied, kgene, krzk, inki.dae
Cc: devicetree, linux-samsung-soc, linux-kernel, dri-devel,
jh80.chung, cw00.choi, Hoegeun Kwon
In-Reply-To: <1483517711-23849-1-git-send-email-hoegeun.kwon@samsung.com>
Before applying the patch, used the of_get_videomode function to
parse the display-timings in the panel which is the child driver
of dsi in the devicetree. this is wrong. So removed the
of_get_videomode and fixed to get videomode struct through
mode_set callback function.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_mic.c | 30 +++++++++++++++++++-----------
1 file changed, 19 insertions(+), 11 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_mic.c b/drivers/gpu/drm/exynos/exynos_drm_mic.c
index a0def0b..a0f459c 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_mic.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_mic.c
@@ -286,13 +286,6 @@ static int parse_dt(struct exynos_mic *mic)
}
nodes[j++] = remote_node;
- ret = of_get_videomode(remote_node,
- &mic->vm, 0);
- if (ret) {
- DRM_ERROR("mic: failed to get videomode");
- goto exit;
- }
-
break;
default:
DRM_ERROR("mic: Unknown endpoint from MIC");
@@ -329,6 +322,24 @@ static void mic_post_disable(struct drm_bridge *bridge)
mutex_unlock(&mic_mutex);
}
+static void mic_mode_set(struct drm_bridge *bridge,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adjusted_mode)
+{
+ struct exynos_mic *mic = bridge->driver_private;
+
+ mutex_lock(&mic_mutex);
+
+ drm_display_mode_to_videomode(mode, &mic->vm);
+
+ if (!mic->i80_mode)
+ mic_set_porch_timing(mic);
+ mic_set_img_size(mic);
+ mic_set_output_timing(mic);
+
+ mutex_unlock(&mic_mutex);
+}
+
static void mic_pre_enable(struct drm_bridge *bridge)
{
struct exynos_mic *mic = bridge->driver_private;
@@ -355,10 +366,6 @@ static void mic_pre_enable(struct drm_bridge *bridge)
goto turn_off_clks;
}
- if (!mic->i80_mode)
- mic_set_porch_timing(mic);
- mic_set_img_size(mic);
- mic_set_output_timing(mic);
mic_set_reg_on(mic, 1);
mic->enabled = 1;
mutex_unlock(&mic_mutex);
@@ -377,6 +384,7 @@ static void mic_enable(struct drm_bridge *bridge) { }
static const struct drm_bridge_funcs mic_bridge_funcs = {
.disable = mic_disable,
.post_disable = mic_post_disable,
+ .mode_set = mic_mode_set,
.pre_enable = mic_pre_enable,
.enable = mic_enable,
};
--
1.9.1
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox