* [PATCH v2 1/3] soc: imx: gpc: add defines for domain index
From: Lucas Stach @ 2017-04-05 13:19 UTC (permalink / raw)
To: Shawn Guo
Cc: Fabio Estevam, Dong Aisheng, devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
patchwork-lst-bIcnvbaLZ9MEGnE8C9+IrQ,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ
Makes referencing a specfic domain in the driver code
less error prone.
Signed-off-by: Lucas Stach <l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
v2: new patch
---
drivers/soc/imx/gpc.c | 12 ++++++++----
1 file changed, 8 insertions(+), 4 deletions(-)
diff --git a/drivers/soc/imx/gpc.c b/drivers/soc/imx/gpc.c
index 4294287e5f6c..d4ebb325b558 100644
--- a/drivers/soc/imx/gpc.c
+++ b/drivers/soc/imx/gpc.c
@@ -235,6 +235,10 @@ static struct platform_driver imx_pgc_power_domain_driver = {
};
builtin_platform_driver(imx_pgc_power_domain_driver)
+#define GPC_PGC_DOMAIN_ARM 0
+#define GPC_PGC_DOMAIN_PU 1
+#define GPC_PGC_DOMAIN_DISPLAY 2
+
static struct genpd_power_state imx6_pm_domain_pu_state = {
.power_off_latency_ns = 25000,
.power_on_latency_ns = 2000000,
@@ -340,7 +344,7 @@ static int imx_gpc_old_dt_init(struct device *dev, struct regmap *regmap,
genpd_err:
for (i = 0; i < num_domains; i++)
pm_genpd_remove(&imx_gpc_domains[i].base);
- imx_pgc_put_clocks(&imx_gpc_domains[1]);
+ imx_pgc_put_clocks(&imx_gpc_domains[GPC_PGC_DOMAIN_PU]);
clk_err:
return ret;
}
@@ -441,12 +445,12 @@ static int imx_gpc_remove(struct platform_device *pdev)
if (!of_get_child_by_name(pdev->dev.of_node, "pgc")) {
of_genpd_del_provider(pdev->dev.of_node);
- ret = pm_genpd_remove(&imx_gpc_domains[1].base);
+ ret = pm_genpd_remove(&imx_gpc_domains[GPC_PGC_DOMAIN_PU].base);
if (ret)
return ret;
- imx_pgc_put_clocks(&imx_gpc_domains[1]);
+ imx_pgc_put_clocks(&imx_gpc_domains[GPC_PGC_DOMAIN_PU]);
- ret = pm_genpd_remove(&imx_gpc_domains[0].base);
+ ret = pm_genpd_remove(&imx_gpc_domains[GPC_PGC_DOMAIN_ARM].base);
if (ret)
return ret;
}
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v4 2/2] i2c: mux: ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch
From: michael.hennerich-OyLXuOCK7orQT0dZR+AlfA @ 2017-04-05 13:07 UTC (permalink / raw)
To: wsa-z923LK4zBo2bacvFa/9K2g, peda-koto5C5qi+TLoDKTGw+V6w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Michael Hennerich
In-Reply-To: <1491397671-14675-1-git-send-email-michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
From: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
This patch adds support for the Analog Devices / Linear Technology
LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches.
The LTC4306 optionally provides two general purpose input/output pins
(GPIOs) that can be configured as logic inputs, opendrain outputs or
push-pull outputs via the generic GPIOLIB framework.
Signed-off-by: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
---
Changes since v1:
- Sort makefile entries
- Sort driver includes
- Use proper defines
- Miscellaneous coding style fixups
- Rename mux select callback
- Revise i2c-mux-idle-disconnect handling
- Add ENABLE GPIO handling on error and device removal.
- Remove surplus of_match_device call.
Changes since v2:
- Stop double error reporting (i2c_mux_add_adapter)
- Change subject
- Split dt bindings to separate patch
Changes since v3:
- Change subject and add spaces
- Convert to I2C_MUX_LOCKED
- Convert to regmap
- Remove local register cache
- Restore previous ENABLE GPIO handling
- Initially pulse ENABLE low
- Eliminate i2c client struct in driver state structure
- Simplify error return path
- Misc minor cleanups
---
MAINTAINERS | 8 +
drivers/i2c/muxes/Kconfig | 11 ++
drivers/i2c/muxes/Makefile | 1 +
drivers/i2c/muxes/i2c-mux-ltc4306.c | 310 ++++++++++++++++++++++++++++++++++++
4 files changed, 330 insertions(+)
create mode 100644 drivers/i2c/muxes/i2c-mux-ltc4306.c
diff --git a/MAINTAINERS b/MAINTAINERS
index c776906..9a27a19 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7698,6 +7698,14 @@ S: Maintained
F: Documentation/hwmon/ltc4261
F: drivers/hwmon/ltc4261.c
+LTC4306 I2C MULTIPLEXER DRIVER
+M: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
+W: http://ez.analog.com/community/linux-device-drivers
+L: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
+S: Supported
+F: drivers/i2c/muxes/i2c-mux-ltc4306.c
+F: Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
+
LTP (Linux Test Project)
M: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
M: Cyril Hrubis <chrubis-AlSwsSmVLrQ@public.gmane.org>
diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig
index 10b3d17..41153b4 100644
--- a/drivers/i2c/muxes/Kconfig
+++ b/drivers/i2c/muxes/Kconfig
@@ -30,6 +30,17 @@ config I2C_MUX_GPIO
This driver can also be built as a module. If so, the module
will be called i2c-mux-gpio.
+config I2C_MUX_LTC4306
+ tristate "LTC LTC4306/5 I2C multiplexer"
+ select GPIOLIB
+ select REGMAP_I2C
+ help
+ If you say yes here you get support for the LTC LTC4306 or LTC4305
+ I2C mux/switch devices.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-mux-ltc4306.
+
config I2C_MUX_PCA9541
tristate "NXP PCA9541 I2C Master Selector"
help
diff --git a/drivers/i2c/muxes/Makefile b/drivers/i2c/muxes/Makefile
index 9948fa4..ff7618c 100644
--- a/drivers/i2c/muxes/Makefile
+++ b/drivers/i2c/muxes/Makefile
@@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE) += i2c-arb-gpio-challenge.o
obj-$(CONFIG_I2C_DEMUX_PINCTRL) += i2c-demux-pinctrl.o
obj-$(CONFIG_I2C_MUX_GPIO) += i2c-mux-gpio.o
+obj-$(CONFIG_I2C_MUX_LTC4306) += i2c-mux-ltc4306.o
obj-$(CONFIG_I2C_MUX_MLXCPLD) += i2c-mux-mlxcpld.o
obj-$(CONFIG_I2C_MUX_PCA9541) += i2c-mux-pca9541.o
obj-$(CONFIG_I2C_MUX_PCA954x) += i2c-mux-pca954x.o
diff --git a/drivers/i2c/muxes/i2c-mux-ltc4306.c b/drivers/i2c/muxes/i2c-mux-ltc4306.c
new file mode 100644
index 0000000..7d34434
--- /dev/null
+++ b/drivers/i2c/muxes/i2c-mux-ltc4306.c
@@ -0,0 +1,310 @@
+/*
+ * Linear Technology LTC4306 and LTC4305 I2C multiplexer/switch
+ *
+ * Copyright (C) 2017 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ *
+ * Based on: i2c-mux-pca954x.c
+ *
+ * Datasheet: http://cds.linear.com/docs/en/datasheet/4306.pdf
+ */
+
+#include <linux/device.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/gpio/driver.h>
+#include <linux/i2c-mux.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define LTC4305_MAX_NCHANS 2
+#define LTC4306_MAX_NCHANS 4
+
+#define LTC_REG_STATUS 0x0
+#define LTC_REG_CONFIG 0x1
+#define LTC_REG_MODE 0x2
+#define LTC_REG_SWITCH 0x3
+
+#define LTC_DOWNSTREAM_ACCL_EN BIT(6)
+#define LTC_UPSTREAM_ACCL_EN BIT(7)
+
+#define LTC_GPIO_ALL_INPUT 0xC0
+#define LTC_SWITCH_MASK 0xF0
+
+enum ltc_type {
+ ltc_4305,
+ ltc_4306,
+};
+
+struct chip_desc {
+ u8 nchans;
+ u8 num_gpios;
+};
+
+struct ltc4306 {
+ struct regmap *regmap;
+ struct gpio_chip gpiochip;
+ const struct chip_desc *chip;
+};
+
+static const struct chip_desc chips[] = {
+ [ltc_4305] = {
+ .nchans = LTC4305_MAX_NCHANS,
+ },
+ [ltc_4306] = {
+ .nchans = LTC4306_MAX_NCHANS,
+ .num_gpios = 2,
+ },
+};
+
+static bool ltc4306_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ return (reg == LTC_REG_CONFIG) ? true : false;
+}
+
+static const struct regmap_config ltc4306_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = LTC_REG_SWITCH,
+ .volatile_reg = ltc4306_is_volatile_reg,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+static int ltc4306_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct ltc4306 *data = gpiochip_get_data(chip);
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(data->regmap, LTC_REG_CONFIG, &val);
+ if (ret < 0)
+ return ret;
+
+ return (val & BIT(1 - offset));
+}
+
+static void ltc4306_gpio_set(struct gpio_chip *chip, unsigned int offset,
+ int value)
+{
+ struct ltc4306 *data = gpiochip_get_data(chip);
+
+ regmap_update_bits(data->regmap, LTC_REG_CONFIG, BIT(5 - offset),
+ value ? BIT(5 - offset) : 0);
+}
+
+static int ltc4306_gpio_direction_input(struct gpio_chip *chip,
+ unsigned int offset)
+{
+ struct ltc4306 *data = gpiochip_get_data(chip);
+
+ return regmap_update_bits(data->regmap, LTC_REG_MODE,
+ BIT(7 - offset), BIT(7 - offset));
+}
+
+static int ltc4306_gpio_direction_output(struct gpio_chip *chip,
+ unsigned int offset, int value)
+{
+ struct ltc4306 *data = gpiochip_get_data(chip);
+
+ ltc4306_gpio_set(chip, offset, value);
+ return regmap_update_bits(data->regmap, LTC_REG_MODE,
+ BIT(7 - offset), 0);
+}
+
+static int ltc4306_gpio_set_config(struct gpio_chip *chip,
+ unsigned int offset, unsigned long config)
+{
+ struct ltc4306 *data = gpiochip_get_data(chip);
+ unsigned int val;
+
+ switch (pinconf_to_config_param(config)) {
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ val = 0;
+ break;
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ val = BIT(4 - offset);
+ break;
+ default:
+ return -ENOTSUPP;
+ }
+
+ return regmap_update_bits(data->regmap, LTC_REG_MODE,
+ BIT(4 - offset), val);
+}
+
+static int ltc4306_gpio_init(struct ltc4306 *data)
+{
+ struct device *dev = regmap_get_device(data->regmap);
+
+ if (!data->chip->num_gpios)
+ return 0;
+
+ data->gpiochip.label = dev_name(dev);
+ data->gpiochip.base = -1;
+ data->gpiochip.ngpio = data->chip->num_gpios;
+ data->gpiochip.parent = dev;
+ data->gpiochip.can_sleep = true;
+ data->gpiochip.direction_input = ltc4306_gpio_direction_input;
+ data->gpiochip.direction_output = ltc4306_gpio_direction_output;
+ data->gpiochip.get = ltc4306_gpio_get;
+ data->gpiochip.set = ltc4306_gpio_set;
+ data->gpiochip.set_config = ltc4306_gpio_set_config;
+ data->gpiochip.owner = THIS_MODULE;
+
+ /* gpiolib assumes all GPIOs default input */
+ regmap_write(data->regmap, LTC_REG_MODE, LTC_GPIO_ALL_INPUT);
+
+ return devm_gpiochip_add_data(dev, &data->gpiochip, data);
+}
+
+static int ltc4306_select_mux(struct i2c_mux_core *muxc, u32 chan)
+{
+ struct ltc4306 *data = i2c_mux_priv(muxc);
+
+ return regmap_update_bits(data->regmap, LTC_REG_SWITCH,
+ LTC_SWITCH_MASK, BIT(7 - chan));
+}
+
+static int ltc4306_deselect_mux(struct i2c_mux_core *muxc, u32 chan)
+{
+ struct ltc4306 *data = i2c_mux_priv(muxc);
+
+ return regmap_update_bits(data->regmap, LTC_REG_SWITCH,
+ LTC_SWITCH_MASK, 0);
+}
+
+static const struct i2c_device_id ltc4306_id[] = {
+ { "ltc4305", ltc_4305 },
+ { "ltc4306", ltc_4306 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ltc4306_id);
+
+static const struct of_device_id ltc4306_of_match[] = {
+ { .compatible = "lltc,ltc4305", .data = &chips[ltc_4305] },
+ { .compatible = "lltc,ltc4306", .data = &chips[ltc_4306] },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ltc4306_of_match);
+
+static int ltc4306_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent);
+ struct device_node *of_node = client->dev.of_node;
+ struct i2c_mux_core *muxc;
+ struct ltc4306 *data;
+ struct gpio_desc *gpio;
+ bool idle_disc = false;
+ int num, ret;
+
+ if (of_node)
+ idle_disc = of_property_read_bool(of_node,
+ "i2c-mux-idle-disconnect");
+
+ muxc = i2c_mux_alloc(adap, &client->dev,
+ LTC4306_MAX_NCHANS, sizeof(*data),
+ I2C_MUX_LOCKED, ltc4306_select_mux,
+ idle_disc ? ltc4306_deselect_mux : NULL);
+ if (!muxc)
+ return -ENOMEM;
+ data = i2c_mux_priv(muxc);
+
+ i2c_set_clientdata(client, muxc);
+
+ data->regmap = devm_regmap_init_i2c(client, <c4306_regmap_config);
+ if (IS_ERR(data->regmap)) {
+ ret = PTR_ERR(data->regmap);
+ dev_err(&client->dev, "Failed to allocate register map: %d\n",
+ ret);
+ return ret;
+ }
+
+ /* Reset and enable the mux if an enable GPIO is specified. */
+ gpio = devm_gpiod_get_optional(&client->dev, "enable", GPIOD_OUT_LOW);
+ if (IS_ERR(gpio))
+ return PTR_ERR(gpio);
+
+ if (gpio) {
+ udelay(1);
+ gpiod_set_value(gpio, 1);
+ }
+
+ /*
+ * Write the mux register at addr to verify
+ * that the mux is in fact present. This also
+ * initializes the mux to disconnected state.
+ */
+ if (regmap_write(data->regmap, LTC_REG_SWITCH, 0) < 0) {
+ dev_warn(&client->dev, "probe failed\n");
+ return -ENODEV;
+ }
+
+ if (of_node) {
+ unsigned int val = 0;
+
+ data->chip = of_device_get_match_data(&client->dev);
+
+ if (of_property_read_bool(of_node,
+ "ltc,downstream-accelerators-enable"))
+ val |= LTC_DOWNSTREAM_ACCL_EN;
+
+ if (of_property_read_bool(of_node,
+ "ltc,upstream-accelerators-enable"))
+ val |= LTC_UPSTREAM_ACCL_EN;
+
+ if (regmap_write(data->regmap, LTC_REG_CONFIG, val) < 0)
+ return -ENODEV;
+ } else {
+ data->chip = &chips[id->driver_data];
+ }
+
+ ret = ltc4306_gpio_init(data);
+ if (ret < 0)
+ return ret;
+
+ /* Now create an adapter for each channel */
+ for (num = 0; num < data->chip->nchans; num++) {
+ ret = i2c_mux_add_adapter(muxc, 0, num, 0);
+ if (ret) {
+ i2c_mux_del_adapters(muxc);
+ return ret;
+ }
+ }
+
+ dev_info(&client->dev,
+ "registered %d multiplexed busses for I2C switch %s\n",
+ num, client->name);
+
+ return 0;
+}
+
+static int ltc4306_remove(struct i2c_client *client)
+{
+ struct i2c_mux_core *muxc = i2c_get_clientdata(client);
+
+ i2c_mux_del_adapters(muxc);
+
+ return 0;
+}
+
+static struct i2c_driver ltc4306_driver = {
+ .driver = {
+ .name = "ltc4306",
+ .of_match_table = of_match_ptr(ltc4306_of_match),
+ },
+ .probe = ltc4306_probe,
+ .remove = ltc4306_remove,
+ .id_table = ltc4306_id,
+};
+
+module_i2c_driver(ltc4306_driver);
+
+MODULE_AUTHOR("Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>");
+MODULE_DESCRIPTION("Linear Technology LTC4306, LTC4305 I2C mux/switch driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v4 1/2] dt-bindings: i2c: mux: ltc4306: Add dt-bindings for I2C multiplexer/switch
From: michael.hennerich-OyLXuOCK7orQT0dZR+AlfA @ 2017-04-05 13:07 UTC (permalink / raw)
To: wsa-z923LK4zBo2bacvFa/9K2g, peda-koto5C5qi+TLoDKTGw+V6w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, Michael Hennerich
From: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
This patch adds support for the Analog Devices / Linear Technology
LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches.
The LTC4306 optionally provides two general purpose input/output pins
(GPIOs) that can be configured as logic inputs, opendrain outputs or
push-pull outputs via the generic GPIOLIB framework.
Signed-off-by: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
.../devicetree/bindings/i2c/i2c-mux-ltc4306.txt | 61 ++++++++++++++++++++++
1 file changed, 61 insertions(+)
create mode 100644 Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
new file mode 100644
index 0000000..1e98c6b
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
@@ -0,0 +1,61 @@
+* Linear Technology / Analog Devices I2C bus switch
+
+Required Properties:
+
+ - compatible: Must contain one of the following.
+ "lltc,ltc4305", "lltc,ltc4306"
+ - reg: The I2C address of the device.
+
+ The following required properties are defined externally:
+
+ - Standard I2C mux properties. See i2c-mux.txt in this directory.
+ - I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional Properties:
+
+ - enable-gpios: Reference to the GPIO connected to the enable input.
+ - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+ children in idle state. This is necessary for example, if there are several
+ multiplexers on the bus and the devices behind them use same I2C addresses.
+ - gpio-controller: Marks the device node as a GPIO Controller.
+ - #gpio-cells: Should be two. The first cell is the pin number and
+ the second cell is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+ - ltc,downstream-accelerators-enable: Enables the rise time accelerators
+ on the downstream port.
+ - ltc,upstream-accelerators-enable: Enables the rise time accelerators
+ on the upstream port.
+
+Example:
+
+ ltc4306: i2c-mux@4a {
+ compatible = "lltc,ltc4306";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x4a>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ eeprom@50 {
+ compatible = "at,24c02";
+ reg = <0x50>;
+ };
+ };
+
+ i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ eeprom@50 {
+ compatible = "at,24c02";
+ reg = <0x50>;
+ };
+ };
+ };
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH 2/3] arm64: allwinner: a64: add USB0 OHCI/EHCI related devicetree parts
From: Maxime Ripard @ 2017-04-05 13:05 UTC (permalink / raw)
To: Icenowy Zheng
Cc: Rob Herring, Chen-Yu Tsai, Kishon Vijay Abraham I,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw
In-Reply-To: <20170405125053.6170-3-icenowy-h8G6r0blFSE@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 1096 bytes --]
On Wed, Apr 05, 2017 at 08:50:52PM +0800, Icenowy Zheng wrote:
> As we added USB0 route auto switching support for A64, add related
> device tree parts to the A64 DTSI file (EHCI0/OHCI0 controllers and the
> pmu0 memory area for PHY).
>
> Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
> ---
> arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 24 ++++++++++++++++++++++++
> 1 file changed, 24 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> index 1c64ea2d23f9..a8916df99048 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
> @@ -179,8 +179,10 @@
> usbphy: phy@01c19400 {
> compatible = "allwinner,sun50i-a64-usb-phy";
> reg = <0x01c19400 0x14>,
> + <0x01c1a800 0x4>,
> <0x01c1b800 0x4>;
> reg-names = "phy_ctrl",
> + "pmu0",
Again, this needs to be split apart, and sent for 4.11.
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply
* Re: [PATCH v4 2/3] Broadcom USB DRD Phy driver for Northstar2
From: Raviteja Garimella @ 2017-04-05 13:00 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: Mark Rutland, devicetree, Scott Branden, Jon Mason, Ray Jui,
Will Deacon, linux-kernel, Rob Herring, BCM Kernel Feedback,
Catalin Marinas, linux-arm-kernel
In-Reply-To: <8aa2cc42-6fdc-5574-4449-f05f6d5cbd38@ti.com>
Hi Kishon,
On Wed, Apr 5, 2017 at 4:30 PM, Kishon Vijay Abraham I <kishon@ti.com> wrote:
> Hi,
>
> On Tuesday 28 March 2017 05:57 PM, Raviteja Garimella wrote:
>> This is driver for USB DRD Phy used in Broadcom's Northstar2
>> SoC. The phy can be configured to be in Device mode or Host
>> mode based on the type of cable connected to the port. The
>> driver registers to extcon framework to get appropriate
>> connect events for Host/Device cables connect/disconnect
>> states based on VBUS and ID interrupts.
>
> $patch should be phy: phy-bcm-ns2-usbdrd: USB DRD Phy driver for Broadcoms
> Northstar2.
>
Will do.
> Sorry for not letting you know this earlier. But I feel the design of the
> driver should be changed. Extcon shouldn't be used here. The extcon
> notifications should be sent to the consumer driver and the consumer driver
> should be responsible for invoking the phy ops.
>
The consumer drivers here would be a UDC driver (USB device
controller), EHCI and OHCI host controller drivers.
I was already suggested in UDC driver review to deal with extcon in Phy driver.
This phy connects to 2 host controllers, and one device controller.
That's the design in Broadcom Northstar2
platform. The values of the VBUS and ID pins of this port are
determined based on the type of the cable (device cable
or host cable). And. phy has to be configured accordingly.
> The phy ops being invoked during extcon events doesn't look right.
Could you please elaborate on the concern, so that we can think of
mitigating those issues in this driver?
Since we are dealing with phy init/shutdown in this driver itself, are
you okay with moving the extcon handling code
out of phy ops ?
Thanks,
Ravi
>
> Thanks
> Kishon
^ permalink raw reply
* Re: [PATCH 1/3] dt: bindings: add pmu0 regs for USB PHYs on Allwinner H3/V3s/A64
From: Kishon Vijay Abraham I @ 2017-04-05 12:58 UTC (permalink / raw)
To: Icenowy Zheng, Rob Herring, Maxime Ripard, Chen-Yu Tsai
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
In-Reply-To: <20170405125053.6170-2-icenowy-h8G6r0blFSE@public.gmane.org>
On Wednesday 05 April 2017 06:20 PM, Icenowy Zheng wrote:
> From: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
>
> Allwinner H3/V3s/A64 SoCs have a special USB PHY0 that can route to two
> controllers: one is MUSB and the other is a EHCI/OHCI pair.
>
> When it's routed to EHCI/OHCI pair, it will needs a "pmu0" regs to
> tweak, like other EHCI/OHCI pairs in Allwinner SoCs.
>
> Add this to the binding of USB PHYs on Allwinner H3/V3s/A64.
>
> Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
> Acked-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
> ---
>
> Kishon, could you push this to 4.11?
Is this for the patch titled "phy: sun4i-usb: add support for V3s USB PHY" that
was added during the last merge window.
this patch looks simpler enough to be merged in this -rc cycle. However it
depends on Greg KH.
Thanks
Kishon
>
> Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> index e42334258185..005bc22938ff 100644
> --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
> @@ -15,6 +15,7 @@ Required properties:
> - reg : a list of offset + length pairs
> - reg-names :
> * "phy_ctrl"
> + * "pmu0" for H3, V3s and A64
> * "pmu1"
> * "pmu2" for sun4i, sun6i or sun7i
> - #phy-cells : from the generic phy bindings, must be 1
>
^ permalink raw reply
* [PATCH 3/3] arm64: allwinner: a64: enable EHCI0/OHCI0 controller for Pine64
From: Icenowy Zheng @ 2017-04-05 12:50 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Kishon Vijay Abraham I
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
In-Reply-To: <20170405125053.6170-1-icenowy-h8G6r0blFSE@public.gmane.org>
The upper USB port of Pine64 board is connected to the SoC's USB0 port,
which can now switch from the MUSB controller to the EHCI/OHCI pair.
Enable the EHCI/OHCI pair in the Pine64 device tree.
Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
---
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
index c680ed385da3..4782add50b94 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
@@ -66,6 +66,10 @@
};
};
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
@@ -91,6 +95,10 @@
status = "okay";
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
--
2.12.2
^ permalink raw reply related
* [PATCH 2/3] arm64: allwinner: a64: add USB0 OHCI/EHCI related devicetree parts
From: Icenowy Zheng @ 2017-04-05 12:50 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Kishon Vijay Abraham I
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
In-Reply-To: <20170405125053.6170-1-icenowy-h8G6r0blFSE@public.gmane.org>
As we added USB0 route auto switching support for A64, add related
device tree parts to the A64 DTSI file (EHCI0/OHCI0 controllers and the
pmu0 memory area for PHY).
Signed-off-by: Icenowy Zheng <icenowy-h8G6r0blFSE@public.gmane.org>
---
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 24 ++++++++++++++++++++++++
1 file changed, 24 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 1c64ea2d23f9..a8916df99048 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -179,8 +179,10 @@
usbphy: phy@01c19400 {
compatible = "allwinner,sun50i-a64-usb-phy";
reg = <0x01c19400 0x14>,
+ <0x01c1a800 0x4>,
<0x01c1b800 0x4>;
reg-names = "phy_ctrl",
+ "pmu0",
"pmu1";
clocks = <&ccu CLK_USB_PHY0>,
<&ccu CLK_USB_PHY1>;
@@ -194,6 +196,28 @@
#phy-cells = <1>;
};
+ ehci0: usb@01c1a000 {
+ compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
+ reg = <0x01c1a000 0x100>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ status = "disabled";
+ };
+
+ ohci0: usb@01c1a400 {
+ compatible = "allwinner,sun50i-a64-ohci", "generic-ohci";
+ reg = <0x01c1a400 0x100>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ status = "disabled";
+ };
+
ehci1: usb@01c1b000 {
compatible = "allwinner,sun50i-a64-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
--
2.12.2
^ permalink raw reply related
* [PATCH 1/3] dt: bindings: add pmu0 regs for USB PHYs on Allwinner H3/V3s/A64
From: Icenowy Zheng @ 2017-04-05 12:50 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Kishon Vijay Abraham I
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
In-Reply-To: <20170405125053.6170-1-icenowy-h8G6r0blFSE@public.gmane.org>
From: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Allwinner H3/V3s/A64 SoCs have a special USB PHY0 that can route to two
controllers: one is MUSB and the other is a EHCI/OHCI pair.
When it's routed to EHCI/OHCI pair, it will needs a "pmu0" regs to
tweak, like other EHCI/OHCI pairs in Allwinner SoCs.
Add this to the binding of USB PHYs on Allwinner H3/V3s/A64.
Signed-off-by: Icenowy Zheng <icenowy-ymACFijhrKM@public.gmane.org>
Acked-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
Signed-off-by: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
---
Kishon, could you push this to 4.11?
Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
index e42334258185..005bc22938ff 100644
--- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt
@@ -15,6 +15,7 @@ Required properties:
- reg : a list of offset + length pairs
- reg-names :
* "phy_ctrl"
+ * "pmu0" for H3, V3s and A64
* "pmu1"
* "pmu2" for sun4i, sun6i or sun7i
- #phy-cells : from the generic phy bindings, must be 1
--
2.12.2
^ permalink raw reply related
* [PATCH 0/3] Allwinner A64 EHCI0/OHCI0 devicetree change
From: Icenowy Zheng @ 2017-04-05 12:50 UTC (permalink / raw)
To: Rob Herring, Maxime Ripard, Chen-Yu Tsai, Kishon Vijay Abraham I
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, Icenowy Zheng
This patchset contains devicetree parts of the EHCI0/OHCI0 controllers
on A64 SoC.
The first patch is a devicetree binding change, which has been planned
for 4.12; however, as Maxime Ripard suggested, it should go in 4.11
as it's part of the device's description.
The second patch added pmu0 regs and EHCI/OHCI controllers for USB0.
The third patch enabled EHCI0/OHCI0 for Pine64 board.
This patchset should go in 4.11 as Maxime Ripard suggested.
Icenowy Zheng (3):
dt: bindings: add pmu0 regs for USB PHYs on Allwinner H3/V3s/A64
arm64: allwinner: a64: add USB0 OHCI/EHCI related devicetree parts
arm64: allwinner: a64: enable EHCI0/OHCI0 controller for Pine64
.../devicetree/bindings/phy/sun4i-usb-phy.txt | 1 +
.../arm64/boot/dts/allwinner/sun50i-a64-pine64.dts | 8 ++++++++
arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 24 ++++++++++++++++++++++
3 files changed, 33 insertions(+)
--
2.12.2
^ permalink raw reply
* [PATCH 0/3] XRA1403,gpio - add XRA1403 gpio expander driver
From: Han, Nandor (GE Healthcare) @ 2017-04-05 12:46 UTC (permalink / raw)
To: Linus Walleij
Cc: Alexandre Courbot, Rob Herring, Mark Rutland,
linux-gpio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
In-Reply-To: <CACRpkdZ-wD5SwBNtSPceV-mwJiAAU_03obk3Gv97kz0MzX7RLw@mail.gmail.com>
> -----Original Message-----
> From: Linus Walleij [mailto:linus.walleij@linaro.org]
> Sent: 29 March 2017 04:51
> To: Han, Nandor (GE Healthcare) <nandor.han@ge.com>
> Cc: Alexandre Courbot <gnurou@gmail.com>; Rob Herring <robh+dt@kernel.org>; Mark Rutland
> <mark.rutland@arm.com>; linux-gpio@vger.kernel.org; devicetree@vger.kernel.org; linux-kernel@vger.kernel.org
> Subject: EXT: Re: [PATCH 0/3] XRA1403,gpio - add XRA1403 gpio expander driver
>
<snip>
> Do *NOT* use the sysfs for testing GPIO.
> This is being phased out.
>
> Use the tools in tools/gpio/* so that you exercise the
> character device instead of the old deprecated ABI.
>
Thanks Linus, really good and helpful comments.
I agree that make more sense to test with tools/gpio/*.
> Yours,
> Linus Walleij
^ permalink raw reply
* [PATCH 2/3] of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
From: Nicholas Piggin @ 2017-04-05 12:37 UTC (permalink / raw)
To: Michael Ellerman, devicetree-u79uwXL29TY76Z2rM5mHXA
Cc: Nicholas Piggin, linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ,
Benjamin Herrenschmidt, Frank Rowand, Rob Herring
In-Reply-To: <20170405123706.6081-1-npiggin-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Introduce primitives for FDT parsing. These will be used for powerpc
cpufeatures node scanning, which has quite complex structure but should
be processed early.
Signed-off-by: Nicholas Piggin <npiggin-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
drivers/of/fdt.c | 39 +++++++++++++++++++++++++++++++++++++++
include/linux/of_fdt.h | 6 ++++++
2 files changed, 45 insertions(+)
diff --git a/drivers/of/fdt.c b/drivers/of/fdt.c
index e5ce4b59e162..a45854fe5156 100644
--- a/drivers/of/fdt.c
+++ b/drivers/of/fdt.c
@@ -754,6 +754,37 @@ int __init of_scan_flat_dt(int (*it)(unsigned long node,
}
/**
+ * of_scan_flat_dt_subnodes - scan sub-nodes of a node call callback on each.
+ * @it: callback function
+ * @data: context data pointer
+ *
+ * This function is used to scan sub-nodes of a node.
+ */
+int __init of_scan_flat_dt_subnodes(unsigned long node,
+ int (*it)(unsigned long node,
+ const char *uname,
+ void *data),
+ void *data)
+{
+ const void *blob = initial_boot_params;
+ const char *pathp;
+ int offset, rc = 0;
+
+ offset = node;
+ for (offset = fdt_first_subnode(blob, offset);
+ offset >= 0 && !rc;
+ offset = fdt_next_subnode(blob, offset)) {
+
+ pathp = fdt_get_name(blob, offset, NULL);
+ if (*pathp == '/')
+ pathp = kbasename(pathp);
+ rc = it(offset, pathp, data);
+ }
+ return rc;
+}
+
+
+/**
* of_get_flat_dt_subnode_by_name - get the subnode by given name
*
* @node: the parent node
@@ -812,6 +843,14 @@ int __init of_flat_dt_match(unsigned long node, const char *const *compat)
return of_fdt_match(initial_boot_params, node, compat);
}
+/**
+ * of_get_flat_dt_prop - Given a node in the flat blob, return the phandle
+ */
+uint32_t __init of_get_flat_dt_phandle(unsigned long node)
+{
+ return fdt_get_phandle(initial_boot_params, node);
+}
+
struct fdt_scan_status {
const char *name;
int namelen;
diff --git a/include/linux/of_fdt.h b/include/linux/of_fdt.h
index 271b3fdf0070..1dfbfd0d8040 100644
--- a/include/linux/of_fdt.h
+++ b/include/linux/of_fdt.h
@@ -54,6 +54,11 @@ extern char __dtb_end[];
extern int of_scan_flat_dt(int (*it)(unsigned long node, const char *uname,
int depth, void *data),
void *data);
+extern int of_scan_flat_dt_subnodes(unsigned long node,
+ int (*it)(unsigned long node,
+ const char *uname,
+ void *data),
+ void *data);
extern int of_get_flat_dt_subnode_by_name(unsigned long node,
const char *uname);
extern const void *of_get_flat_dt_prop(unsigned long node, const char *name,
@@ -62,6 +67,7 @@ extern int of_flat_dt_is_compatible(unsigned long node, const char *name);
extern int of_flat_dt_match(unsigned long node, const char *const *matches);
extern unsigned long of_get_flat_dt_root(void);
extern int of_get_flat_dt_size(void);
+extern uint32_t of_get_flat_dt_phandle(unsigned long node);
extern int early_init_dt_scan_chosen(unsigned long node, const char *uname,
int depth, void *data);
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* Re: [PATCH v2 1/3] clk: vc5: Add structure to describe particular chip features
From: Alexey Firago @ 2017-04-05 12:36 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Michael Turquette, Stephen Boyd, Rob Herring, Marek Vasut,
linux-clk, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
In-Reply-To: <CAMuHMdXEa=1__WMtsRphKbN6h+jVkP7szudENsM3hvGSzDfbwg-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
Hi Geert,
On 05.04.2017 15:15, Geert Uytterhoeven wrote:
> Hi Alexey,
>
> On Wed, Apr 5, 2017 at 1:46 PM, Alexey Firago <alexey_firago-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org> wrote:
>> Introduce vc5_chip_info structure to describe features of a particular
>> VC5 chip (id, number of FODs, number of outputs, flags).
>> For now flags are only used to indicate if chip has internal XTAL.
>> vc5_chip_info is set on probe from the matched of_device_id->data.
>>
>> Also add defines to specify maximum number of FODs and clock outputs
>> supported by the driver.
>>
>> With these changes it should be easier to extend driver to support
>> more VC5 models.
>>
>> Signed-off-by: Alexey Firago <alexey_firago-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
>
> Thanks for your patch!
>
> Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
>
>> --- a/drivers/clk/clk-versaclock5.c
>> +++ b/drivers/clk/clk-versaclock5.c
>> @@ -113,12 +113,30 @@
>> #define VC5_MUX_IN_XIN BIT(0)
>> #define VC5_MUX_IN_CLKIN BIT(1)
>>
>> +/* Maximum number of clk_out supported by this driver */
>> +#define VC5_MAX_CLK_OUT_NUM 3
>> +
>> +/* Maximum number of FODs supported by this driver */
>> +#define VC5_MAX_FOD_NUM 2
>> +
>> +/* flags to describe chip features */
>> +/* chip has built-in oscilator */
>> +#define VC5_HAS_INTERNAL_XTAL BIT(0)
>
> VC5_HAS_INTERNAL_OSC?
I'm fine with renaming it, but shouldn't it be consistent with the rest
of the driver (see "internal-xtal", VC5_XTAL*, etc) and IDT datasheet?
>
>> +
>> /* Supported IDT VC5 models. */
>> enum vc5_model {
>> IDT_VC5_5P49V5923,
>> IDT_VC5_5P49V5933,
>> };
>>
>> +/* Structure to describe features of a particular VC5 model */
>> +struct vc5_chip_info {
>> + const enum vc5_model model;
>> + const int clk_fod_cnt;
>> + const int clk_out_cnt;
>
> const unsigned int (both)
Will fix.
>
>> + u32 flags;
>> +};
>> +
>> struct vc5_driver_data;
>>
>> struct vc5_hw_data {
>> @@ -132,15 +150,15 @@ struct vc5_hw_data {
>> struct vc5_driver_data {
>> struct i2c_client *client;
>> struct regmap *regmap;
>> - enum vc5_model model;
>> + struct vc5_chip_info *chip_info;
>
> const struct vc5_chip_info *chip_info;
>
>> @@ -591,7 +609,7 @@ static int vc5_probe(struct i2c_client *client,
>> struct vc5_driver_data *vc5;
>> struct clk_init_data init;
>> const char *parent_names[2];
>> - unsigned int n, idx;
>> + unsigned int n, idx = 0;
>> int ret;
>>
>> vc5 = devm_kzalloc(&client->dev, sizeof(*vc5), GFP_KERNEL);
>> @@ -600,7 +618,12 @@ static int vc5_probe(struct i2c_client *client,
>>
>> i2c_set_clientdata(client, vc5);
>> vc5->client = client;
>> - vc5->model = (enum vc5_model)of_id->data;
>> +
>> + vc5->chip_info = (struct vc5_chip_info *)of_id->data;
>
> I think the cast is no longer needed when chip_info becomes const.
>
> BTW, of_id is not really needed if you write it like:
>
> vc5->chip_info = of_device_get_match_data(&client->dev);
>
>> + if (!vc5->chip_info) {
>
> This can't really happen, can it?
Ok. Will rework.
>
>> + dev_err(&client->dev, "No device match found\n");
>> + return -ENODEV;
>> + }
>>
>> vc5->pin_xin = devm_clk_get(&client->dev, "xin");
>> if (PTR_ERR(vc5->pin_xin) == -EPROBE_DEFER)
>> @@ -622,8 +645,8 @@ static int vc5_probe(struct i2c_client *client,
>> if (!IS_ERR(vc5->pin_xin)) {
>> vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
>> parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
>> - } else if (vc5->model == IDT_VC5_5P49V5933) {
>> - /* IDT VC5 5P49V5933 has built-in oscilator. */
>> + } else if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL) {
>> + /* chip has built-in oscilator. */
>
> The comment is no longer needed when the bit is named VC5_HAS_INTERNAL_OSC :-)
Ok. Will kill it.
Thanks for your review!
Regards,
Alexey
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH V7 4/4] phy: qcom-qmp: new qmp phy driver for qcom-chipsets
From: Vivek Gautam @ 2017-04-05 12:32 UTC (permalink / raw)
To: kishon, robh+dt
Cc: mark.rutland, devicetree, linux-arm-msm, linux-usb, sboyd,
linux-kernel, bjorn.andersson, srinivas.kandagatla, Vivek Gautam,
linux-arm-kernel
In-Reply-To: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org>
Qualcomm SOCs have QMP phy controller that provides support
to a number of controller, viz. PCIe, UFS, and USB.
Add a new driver, based on generic phy framework, for this
phy controller.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
Changes since v6:
- Rebased on phy/next and *not* including phy grouping series.
Changes since v5:
- Rebased on top of phy grouping series. So the driver now sits in
drivers/phy/qualcomm/
- Removed instances of readl_relaxed() and writel_relaxed(), and using
readl() and writel() instead.
- Replaced regulator handling with regulator_bulk() apis, so that
qusb2_phy_toggle_power() method is completely dropped.
- Removed memory barriers from the driver. Instead, added an extra readl()
over the register in qphy_setbits() and qphy_clrbits() to ensure that
the write is through to the device.
- Fixed nits about return statement from probe(), phy_pipe_clk_register()
and qcom_qmp_phy_create().
Changes since v4:
- Added provision for child nodes representing each phy lane.
Each of these nodes have their own register space for tx, rx and pcs
blocks. Added provision in qcom_qmp_phy_create() to iomap these
address spaces.
- Added list of clocks and resets that are mandatory for each phy.
qcom_qmp_phy_clk_init(), and qcom_qmp_phy_reset_init() methods
request this list and maintains it with qmp.
The clocks and resets are then enabled/de-asserted based on this list.
This list is also updated in the binding documentation.
- Removed qcom_qmp_phy_xlate() method as we don't need it with
#phy-cells 0.
- Removed unnecessary of_match_ptr() cast for the match table,
since the driver is compiled for CONFIG_OF.
- Updated copyright year to 2017.
Changes since v3:
- Renamed 'struct qcom_qmp_phy' to 'struct qcom_qmp' and
'struct qmp_phy_desc' to 'struct qmp_phy' to avoid any confusion
in distinguishing between QMP phy block and per-lane phy which is
the actual phy in Linux eyes (suggested by Bjorn Andersson).
- Made error labels more idiomatic.
- Modified status checking for phy pcs.
- Fixed power_down_delay check.
- Refactored phy_pipe_clk_register() to register the pipe clock source
using devm_clk_hw_register() (suggested by Stephen).
- qcom_qmp_phy_xlate() function:
- Removed unnecessary 'for loop'.
- Added additional check for '0' or -ve args_count.
- Fixed the mixed tabs and spaces in pipe_clk_src diagram.
- Removed instances of memset() since we use snprintf() for the
buffers.
- Refactored qphy_setbits() and qphy_clrbits() a little bit to accept
base address and register offset as two separate arguments.
Changes since v2:
- Removed selecting 'RESET_CONTROLLER' config.
- Added error handling for clk_prepare_enable paths.
- Removed 'ref_clk_src' handling. Driver doesn't need to request and
handle this clock.
- Using readl_poll_timeout() to simplify pcs ready status polling.
Also fixed the polling condition for pcs block ready status:
'Common block ready status bit is set on phy init completion, while
PCS block ready status bit (PHYSTATUS) is reset on phy init
completion.'
- Moved out the per-lane phy creation from probe() to separate
function.
- Registering pipe clock source as a fixed rate clock that comes
out of the PLL block of QMP phy. These source clocks serve as
parent to 'pipe_clks' that are requested by pcie or usb3 phys.
- Using of_device_get_match_data() to get match data.
- Fixed sparse warnings for 'static' and 'const'.
- Using shorter variable names in structure and in functions.
- Handling various comment style shortcomings.
Changes since v1:
- Fixed missing mutex_unlock() calls in error cases, reported by
Julia Lawall.
- Selecting CONFIG_RESET_CONTROLLER when this driver is enabled.
- Added a boolean property to check if the phy has individual lane
reset available.
- Took care or EPROBE_DEFER, dev_vdbg() and other minor nits.
- Removed references to non-lkml links from commit message.
- Moved to use separate iomem resources for each lanes.
Tx, Rx and PCS offsets per lane can now come from dt bindings.
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-qmp.c | 1153 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 1162 insertions(+)
create mode 100644 drivers/phy/phy-qcom-qmp.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index ccc9178e32cd..bb8140355608 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -439,6 +439,14 @@ config PHY_STIH407_USB
Enable this support to enable the picoPHY device used by USB2
and USB3 controllers on STMicroelectronics STiH407 SoC families.
+config PHY_QCOM_QMP
+ tristate "Qualcomm QMP PHY Driver"
+ depends on OF && (ARCH_QCOM || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ Enable this to support the QMP PHY transceiver that is used
+ with controllers such as PCIe, UFS, and USB on Qualcomm chips.
+
config PHY_QCOM_QUSB2
tristate "Qualcomm QUSB2 PHY Driver"
depends on OF && (ARCH_QCOM || COMPILE_TEST)
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 0375c6a32697..5347e6feb292 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
+obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o
obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
diff --git a/drivers/phy/phy-qcom-qmp.c b/drivers/phy/phy-qcom-qmp.c
new file mode 100644
index 000000000000..153b6252b189
--- /dev/null
+++ b/drivers/phy/phy-qcom-qmp.c
@@ -0,0 +1,1153 @@
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/phy/phy.h>
+
+/* QMP PHY QSERDES COM registers */
+#define QSERDES_COM_BG_TIMER 0x00c
+#define QSERDES_COM_SSC_EN_CENTER 0x010
+#define QSERDES_COM_SSC_ADJ_PER1 0x014
+#define QSERDES_COM_SSC_ADJ_PER2 0x018
+#define QSERDES_COM_SSC_PER1 0x01c
+#define QSERDES_COM_SSC_PER2 0x020
+#define QSERDES_COM_SSC_STEP_SIZE1 0x024
+#define QSERDES_COM_SSC_STEP_SIZE2 0x028
+#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN 0x034
+#define QSERDES_COM_CLK_ENABLE1 0x038
+#define QSERDES_COM_SYS_CLK_CTRL 0x03c
+#define QSERDES_COM_SYSCLK_BUF_ENABLE 0x040
+#define QSERDES_COM_PLL_IVCO 0x048
+#define QSERDES_COM_LOCK_CMP1_MODE0 0x04c
+#define QSERDES_COM_LOCK_CMP2_MODE0 0x050
+#define QSERDES_COM_LOCK_CMP3_MODE0 0x054
+#define QSERDES_COM_LOCK_CMP1_MODE1 0x058
+#define QSERDES_COM_LOCK_CMP2_MODE1 0x05c
+#define QSERDES_COM_LOCK_CMP3_MODE1 0x060
+#define QSERDES_COM_BG_TRIM 0x070
+#define QSERDES_COM_CLK_EP_DIV 0x074
+#define QSERDES_COM_CP_CTRL_MODE0 0x078
+#define QSERDES_COM_CP_CTRL_MODE1 0x07c
+#define QSERDES_COM_PLL_RCTRL_MODE0 0x084
+#define QSERDES_COM_PLL_RCTRL_MODE1 0x088
+#define QSERDES_COM_PLL_CCTRL_MODE0 0x090
+#define QSERDES_COM_PLL_CCTRL_MODE1 0x094
+#define QSERDES_COM_SYSCLK_EN_SEL 0x0ac
+#define QSERDES_COM_RESETSM_CNTRL 0x0b4
+#define QSERDES_COM_RESTRIM_CTRL 0x0bc
+#define QSERDES_COM_RESCODE_DIV_NUM 0x0c4
+#define QSERDES_COM_LOCK_CMP_EN 0x0c8
+#define QSERDES_COM_LOCK_CMP_CFG 0x0cc
+#define QSERDES_COM_DEC_START_MODE0 0x0d0
+#define QSERDES_COM_DEC_START_MODE1 0x0d4
+#define QSERDES_COM_DIV_FRAC_START1_MODE0 0x0dc
+#define QSERDES_COM_DIV_FRAC_START2_MODE0 0x0e0
+#define QSERDES_COM_DIV_FRAC_START3_MODE0 0x0e4
+#define QSERDES_COM_DIV_FRAC_START1_MODE1 0x0e8
+#define QSERDES_COM_DIV_FRAC_START2_MODE1 0x0ec
+#define QSERDES_COM_DIV_FRAC_START3_MODE1 0x0f0
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE0 0x108
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE0 0x10c
+#define QSERDES_COM_INTEGLOOP_GAIN0_MODE1 0x110
+#define QSERDES_COM_INTEGLOOP_GAIN1_MODE1 0x114
+#define QSERDES_COM_VCO_TUNE_CTRL 0x124
+#define QSERDES_COM_VCO_TUNE_MAP 0x128
+#define QSERDES_COM_VCO_TUNE1_MODE0 0x12c
+#define QSERDES_COM_VCO_TUNE2_MODE0 0x130
+#define QSERDES_COM_VCO_TUNE1_MODE1 0x134
+#define QSERDES_COM_VCO_TUNE2_MODE1 0x138
+#define QSERDES_COM_VCO_TUNE_TIMER1 0x144
+#define QSERDES_COM_VCO_TUNE_TIMER2 0x148
+#define QSERDES_COM_BG_CTRL 0x170
+#define QSERDES_COM_CLK_SELECT 0x174
+#define QSERDES_COM_HSCLK_SEL 0x178
+#define QSERDES_COM_CORECLK_DIV 0x184
+#define QSERDES_COM_CORE_CLK_EN 0x18c
+#define QSERDES_COM_C_READY_STATUS 0x190
+#define QSERDES_COM_CMN_CONFIG 0x194
+#define QSERDES_COM_SVS_MODE_CLK_SEL 0x19c
+#define QSERDES_COM_DEBUG_BUS0 0x1a0
+#define QSERDES_COM_DEBUG_BUS1 0x1a4
+#define QSERDES_COM_DEBUG_BUS2 0x1a8
+#define QSERDES_COM_DEBUG_BUS3 0x1ac
+#define QSERDES_COM_DEBUG_BUS_SEL 0x1b0
+#define QSERDES_COM_CORECLK_DIV_MODE1 0x1bc
+
+/* QMP PHY TX registers */
+#define QSERDES_TX_RES_CODE_LANE_OFFSET 0x054
+#define QSERDES_TX_DEBUG_BUS_SEL 0x064
+#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN 0x068
+#define QSERDES_TX_LANE_MODE 0x094
+#define QSERDES_TX_RCV_DETECT_LVL_2 0x0ac
+
+/* QMP PHY RX registers */
+#define QSERDES_RX_UCDR_SO_GAIN_HALF 0x010
+#define QSERDES_RX_UCDR_SO_GAIN 0x01c
+#define QSERDES_RX_UCDR_FASTLOCK_FO_GAIN 0x040
+#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE 0x048
+#define QSERDES_RX_RX_TERM_BW 0x090
+#define QSERDES_RX_RX_EQ_GAIN1_LSB 0x0c4
+#define QSERDES_RX_RX_EQ_GAIN1_MSB 0x0c8
+#define QSERDES_RX_RX_EQ_GAIN2_LSB 0x0cc
+#define QSERDES_RX_RX_EQ_GAIN2_MSB 0x0d0
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2 0x0d8
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3 0x0dc
+#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4 0x0e0
+#define QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1 0x108
+#define QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2 0x10c
+#define QSERDES_RX_SIGDET_ENABLES 0x110
+#define QSERDES_RX_SIGDET_CNTRL 0x114
+#define QSERDES_RX_SIGDET_LVL 0x118
+#define QSERDES_RX_SIGDET_DEGLITCH_CNTRL 0x11c
+#define QSERDES_RX_RX_BAND 0x120
+#define QSERDES_RX_RX_INTERFACE_MODE 0x12c
+
+/* QMP PHY PCS registers */
+#define QPHY_POWER_DOWN_CONTROL 0x04
+#define QPHY_TXDEEMPH_M6DB_V0 0x24
+#define QPHY_TXDEEMPH_M3P5DB_V0 0x28
+#define QPHY_ENDPOINT_REFCLK_DRIVE 0x54
+#define QPHY_RX_IDLE_DTCT_CNTRL 0x58
+#define QPHY_POWER_STATE_CONFIG1 0x60
+#define QPHY_POWER_STATE_CONFIG2 0x64
+#define QPHY_POWER_STATE_CONFIG4 0x6c
+#define QPHY_LOCK_DETECT_CONFIG1 0x80
+#define QPHY_LOCK_DETECT_CONFIG2 0x84
+#define QPHY_LOCK_DETECT_CONFIG3 0x88
+#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0
+#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4
+
+/* QPHY_SW_RESET bit */
+#define SW_RESET BIT(0)
+/* QPHY_POWER_DOWN_CONTROL */
+#define SW_PWRDN BIT(0)
+#define REFCLK_DRV_DSBL BIT(1)
+/* QPHY_START_CONTROL bits */
+#define SERDES_START BIT(0)
+#define PCS_START BIT(1)
+#define PLL_READY_GATE_EN BIT(3)
+/* QPHY_PCS_STATUS bit */
+#define PHYSTATUS BIT(6)
+/* QPHY_COM_PCS_READY_STATUS bit */
+#define PCS_READY BIT(0)
+
+#define PHY_INIT_COMPLETE_TIMEOUT 1000
+#define POWER_DOWN_DELAY_US_MIN 10
+#define POWER_DOWN_DELAY_US_MAX 11
+
+#define MAX_PROP_NAME 32
+
+struct qmp_phy_init_tbl {
+ unsigned int offset;
+ unsigned int val;
+ /*
+ * register part of layout ?
+ * if yes, then offset gives index in the reg-layout
+ */
+ int in_layout;
+};
+#define QMP_PHY_INIT_CFG(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ }
+#define QMP_PHY_INIT_CFG_L(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ .in_layout = 1, \
+ }
+
+/* set of registers with offsets different per-PHY */
+enum qphy_reg_layout {
+ /* Common block control registers */
+ QPHY_COM_SW_RESET,
+ QPHY_COM_POWER_DOWN_CONTROL,
+ QPHY_COM_START_CONTROL,
+ QPHY_COM_PCS_READY_STATUS,
+ /* PCS registers */
+ QPHY_PLL_LOCK_CHK_DLY_TIME,
+ QPHY_FLL_CNTRL1,
+ QPHY_FLL_CNTRL2,
+ QPHY_FLL_CNT_VAL_L,
+ QPHY_FLL_CNT_VAL_H_TOL,
+ QPHY_FLL_MAN_CODE,
+ QPHY_SW_RESET,
+ QPHY_START_CTRL,
+ QPHY_PCS_READY_STATUS,
+};
+
+static const unsigned int pciephy_regs_layout[] = {
+ [QPHY_COM_SW_RESET] = 0x400,
+ [QPHY_COM_POWER_DOWN_CONTROL] = 0x404,
+ [QPHY_COM_START_CONTROL] = 0x408,
+ [QPHY_COM_PCS_READY_STATUS] = 0x448,
+ [QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8,
+ [QPHY_FLL_CNTRL1] = 0xc4,
+ [QPHY_FLL_CNTRL2] = 0xc8,
+ [QPHY_FLL_CNT_VAL_L] = 0xcc,
+ [QPHY_FLL_CNT_VAL_H_TOL] = 0xd0,
+ [QPHY_FLL_MAN_CODE] = 0xd4,
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x174,
+};
+
+static const unsigned int usb3phy_regs_layout[] = {
+ [QPHY_FLL_CNTRL1] = 0xc0,
+ [QPHY_FLL_CNTRL2] = 0xc4,
+ [QPHY_FLL_CNT_VAL_L] = 0xc8,
+ [QPHY_FLL_CNT_VAL_H_TOL] = 0xcc,
+ [QPHY_FLL_MAN_CODE] = 0xd0,
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x17c,
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x42),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x09),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x1a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESCODE_DIV_NUM, 0x40),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_BAND, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x19),
+};
+
+static const struct qmp_phy_init_tbl msm8996_pcie_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_RX_IDLE_DTCT_CNTRL, 0x4c),
+ QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x01),
+
+ QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x05),
+
+ QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x05),
+ QMP_PHY_INIT_CFG(QPHY_POWER_DOWN_CONTROL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG4, 0x00),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG1, 0xa3),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0x0e),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x08),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x04),
+ /* PLL and Loop filter settings */
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0x15),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0x34),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_CFG, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0x0a),
+ /* SSC settings */
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0xde),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x06),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xbb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x03),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_LVL, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x16),
+};
+
+static const struct qmp_phy_init_tbl msm8996_usb3_pcs_tbl[] = {
+ /* FLL settings */
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL2, 0x03),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNTRL1, 0x02),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_L, 0x09),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_CNT_VAL_H_TOL, 0x42),
+ QMP_PHY_INIT_CFG_L(QPHY_FLL_MAN_CODE, 0x85),
+
+ /* Lock Det settings */
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG1, 0xd1),
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG2, 0x1f),
+ QMP_PHY_INIT_CFG(QPHY_LOCK_DETECT_CONFIG3, 0x47),
+ QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08),
+};
+
+/* struct qmp_phy_cfg - per-PHY initialization config */
+struct qmp_phy_cfg {
+ /* phy-type - PCIE/UFS/USB */
+ unsigned int type;
+ /* number of lanes provided by phy */
+ int nlanes;
+
+ /* Init sequence for PHY blocks - serdes, tx, rx, pcs */
+ const struct qmp_phy_init_tbl *serdes_tbl;
+ int serdes_tbl_num;
+ const struct qmp_phy_init_tbl *tx_tbl;
+ int tx_tbl_num;
+ const struct qmp_phy_init_tbl *rx_tbl;
+ int rx_tbl_num;
+ const struct qmp_phy_init_tbl *pcs_tbl;
+ int pcs_tbl_num;
+
+ /* clock ids to be requested */
+ const char * const *clk_list;
+ int num_clks;
+ /* resets to be requested */
+ const char * const *reset_list;
+ int num_resets;
+ /* regulators to be requested */
+ const char * const *vreg_list;
+ int num_vregs;
+
+ /* array of registers with different offsets */
+ const unsigned int *regs;
+
+ unsigned int start_ctrl;
+ unsigned int pwrdn_ctrl;
+ unsigned int mask_pcs_ready;
+ unsigned int mask_com_pcs_ready;
+
+ /* true, if PHY has a separate PHY_COM control block */
+ bool has_phy_com_ctrl;
+ /* true, if PHY has a reset for individual lanes */
+ bool has_lane_rst;
+ /* true, if PHY needs delay after POWER_DOWN */
+ bool has_pwrdn_delay;
+ /* power_down delay in usec */
+ int pwrdn_delay_min;
+ int pwrdn_delay_max;
+};
+
+/**
+ * struct qmp_phy - per-lane phy descriptor
+ *
+ * @phy: generic phy
+ * @tx: iomapped memory space for lane's tx
+ * @rx: iomapped memory space for lane's rx
+ * @pcs: iomapped memory space for lane's pcs
+ * @pipe_clk: pipe lock
+ * @index: lane index
+ * @qmp: QMP phy to which this lane belongs
+ * @lane_rst: lane's reset controller
+ */
+struct qmp_phy {
+ struct phy *phy;
+ void __iomem *tx;
+ void __iomem *rx;
+ void __iomem *pcs;
+ struct clk *pipe_clk;
+ unsigned int index;
+ struct qcom_qmp *qmp;
+ struct reset_control *lane_rst;
+};
+
+/**
+ * struct qcom_qmp - structure holding QMP phy block attributes
+ *
+ * @dev: device
+ * @serdes: iomapped memory space for phy's serdes
+ *
+ * @clks: array of clocks required by phy
+ * @resets: array of resets required by phy
+ * @vregs: regulator supplies bulk data
+ *
+ * @cfg: phy specific configuration
+ * @phys: array of per-lane phy descriptors
+ * @phy_mutex: mutex lock for PHY common block initialization
+ * @init_count: phy common block initialization count
+ */
+struct qcom_qmp {
+ struct device *dev;
+ void __iomem *serdes;
+
+ struct clk **clks;
+ struct reset_control **resets;
+ struct regulator_bulk_data *vregs;
+
+ const struct qmp_phy_cfg *cfg;
+ struct qmp_phy **phys;
+
+ struct mutex phy_mutex;
+ int init_count;
+};
+
+static inline void qphy_setbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg |= val;
+ writel(reg, base + offset);
+
+ /* ensure that above write is through */
+ readl(base + offset);
+}
+
+static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg &= ~val;
+ writel(reg, base + offset);
+
+ /* ensure that above write is through */
+ readl(base + offset);
+}
+
+/* list of clocks required by phy */
+static const char * const msm8996_phy_clk_l[] = {
+ "aux", "cfg_ahb", "ref",
+};
+
+/* list of resets */
+static const char * const msm8996_pciephy_reset_l[] = {
+ "phy", "common", "cfg",
+};
+
+static const char * const msm8996_usb3phy_reset_l[] = {
+ "phy", "common",
+};
+
+/* list of regulators */
+static const char * const msm8996_phy_vreg_l[] = {
+ "vdda-phy", "vdda-pll",
+};
+
+static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
+ .type = PHY_TYPE_PCIE,
+ .nlanes = 3,
+
+ .serdes_tbl = msm8996_pcie_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(msm8996_pcie_serdes_tbl),
+ .tx_tbl = msm8996_pcie_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(msm8996_pcie_tx_tbl),
+ .rx_tbl = msm8996_pcie_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(msm8996_pcie_rx_tbl),
+ .pcs_tbl = msm8996_pcie_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(msm8996_pcie_pcs_tbl),
+ .clk_list = msm8996_phy_clk_l,
+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
+ .reset_list = msm8996_pciephy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_pciephy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = pciephy_regs_layout,
+
+ .start_ctrl = PCS_START | PLL_READY_GATE_EN,
+ .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
+ .mask_com_pcs_ready = PCS_READY,
+
+ .has_phy_com_ctrl = true,
+ .has_lane_rst = true,
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
+ .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
+};
+
+static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
+ .type = PHY_TYPE_USB3,
+ .nlanes = 1,
+
+ .serdes_tbl = msm8996_usb3_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(msm8996_usb3_serdes_tbl),
+ .tx_tbl = msm8996_usb3_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(msm8996_usb3_tx_tbl),
+ .rx_tbl = msm8996_usb3_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(msm8996_usb3_rx_tbl),
+ .pcs_tbl = msm8996_usb3_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(msm8996_usb3_pcs_tbl),
+ .clk_list = msm8996_phy_clk_l,
+ .num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
+ .reset_list = msm8996_usb3phy_reset_l,
+ .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+ .vreg_list = msm8996_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .regs = usb3phy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PHYSTATUS,
+};
+
+static void qcom_qmp_phy_configure(void __iomem *base,
+ const unsigned int *regs,
+ const struct qmp_phy_init_tbl tbl[],
+ int num)
+{
+ int i;
+ const struct qmp_phy_init_tbl *t = tbl;
+
+ if (!t)
+ return;
+
+ for (i = 0; i < num; i++, t++) {
+ if (t->in_layout)
+ writel(t->val, base + regs[t->offset]);
+ else
+ writel(t->val, base + t->offset);
+ }
+}
+
+static int qcom_qmp_phy_poweron(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ int num = qmp->cfg->num_vregs;
+ int ret;
+
+ dev_vdbg(&phy->dev, "Powering on QMP phy\n");
+
+ /* turn on regulator supplies */
+ ret = regulator_bulk_enable(num, qmp->vregs);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable regulators, err=%d\n", ret);
+ return ret;
+ }
+
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(qmp->dev, "pipe_clk enable failed, err=%d\n", ret);
+ regulator_bulk_disable(num, qmp->vregs);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int qcom_qmp_phy_poweroff(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+
+ clk_disable_unprepare(qphy->pipe_clk);
+
+ regulator_bulk_disable(qmp->cfg->num_vregs, qmp->vregs);
+
+ return 0;
+}
+
+static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
+{
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *serdes = qmp->serdes;
+ int ret, i;
+
+ mutex_lock(&qmp->phy_mutex);
+ if (qmp->init_count++) {
+ mutex_unlock(&qmp->phy_mutex);
+ return 0;
+ }
+
+ for (i = 0; i < cfg->num_resets; i++) {
+ ret = reset_control_deassert(qmp->resets[i]);
+ if (ret) {
+ dev_err(qmp->dev, "%s reset deassert failed\n",
+ qmp->cfg->reset_list[i]);
+ while (--i >= 0)
+ reset_control_assert(qmp->resets[i]);
+ goto err_rst;
+ }
+ }
+
+ if (cfg->has_phy_com_ctrl)
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
+
+ /* Serdes configuration */
+ qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl,
+ cfg->serdes_tbl_num);
+
+ if (cfg->has_phy_com_ctrl) {
+ void __iomem *status;
+ unsigned int mask, val;
+
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
+ SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
+
+ status = serdes + cfg->regs[QPHY_COM_PCS_READY_STATUS];
+ mask = cfg->mask_com_pcs_ready;
+
+ ret = readl_poll_timeout(status, val, (val & mask), 10,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev,
+ "phy common block init timed-out\n");
+ goto err_com_init;
+ }
+ }
+
+ mutex_unlock(&qmp->phy_mutex);
+
+ return 0;
+
+err_com_init:
+ while (--i >= 0)
+ reset_control_assert(qmp->resets[i]);
+err_rst:
+ mutex_unlock(&qmp->phy_mutex);
+ return ret;
+}
+
+static int qcom_qmp_phy_com_exit(struct qcom_qmp *qmp)
+{
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *serdes = qmp->serdes;
+ int i = cfg->num_resets;
+
+ mutex_lock(&qmp->phy_mutex);
+ if (--qmp->init_count) {
+ mutex_unlock(&qmp->phy_mutex);
+ return 0;
+ }
+
+ if (cfg->has_phy_com_ctrl) {
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_START_CONTROL],
+ SERDES_START | PCS_START);
+ qphy_clrbits(serdes, cfg->regs[QPHY_COM_SW_RESET],
+ SW_RESET);
+ qphy_setbits(serdes, cfg->regs[QPHY_COM_POWER_DOWN_CONTROL],
+ SW_PWRDN);
+ }
+
+ while (--i >= 0)
+ reset_control_assert(qmp->resets[i]);
+
+ mutex_unlock(&qmp->phy_mutex);
+
+ return 0;
+}
+
+/* PHY Initialization */
+static int qcom_qmp_phy_init(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *tx = qphy->tx;
+ void __iomem *rx = qphy->rx;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *status;
+ unsigned int mask, val;
+ int ret, i;
+
+ dev_vdbg(qmp->dev, "Initializing QMP phy\n");
+
+ for (i = 0; i < qmp->cfg->num_clks; i++) {
+ ret = clk_prepare_enable(qmp->clks[i]);
+ if (ret) {
+ dev_err(qmp->dev, "failed to enable %s clk, err=%d\n",
+ qmp->cfg->clk_list[i], ret);
+ while (--i >= 0)
+ clk_disable_unprepare(qmp->clks[i]);
+ }
+ }
+
+ ret = qcom_qmp_phy_com_init(qmp);
+ if (ret)
+ goto err_com_init;
+
+ if (cfg->has_lane_rst) {
+ ret = reset_control_deassert(qphy->lane_rst);
+ if (ret) {
+ dev_err(qmp->dev, "lane%d reset deassert failed\n",
+ qphy->index);
+ goto err_lane_rst;
+ }
+ }
+
+ /* Tx, Rx, and PCS configurations */
+ qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
+ qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
+ qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+
+ /*
+ * Pull out PHY from POWER DOWN state.
+ * This is active low enable signal to power-down PHY.
+ */
+ qphy_setbits(pcs, QPHY_POWER_DOWN_CONTROL, cfg->pwrdn_ctrl);
+
+ if (cfg->has_pwrdn_delay)
+ usleep_range(cfg->pwrdn_delay_min, cfg->pwrdn_delay_max);
+
+ /* start SerDes and Phy-Coding-Sublayer */
+ qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+ /* Pull PHY out of reset state */
+ qphy_clrbits(pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+
+ status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
+ mask = cfg->mask_pcs_ready;
+
+ ret = readl_poll_timeout(status, val, !(val & mask), 1,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev, "phy initialization timed-out\n");
+ goto err_pcs_ready;
+ }
+
+ return ret;
+
+err_pcs_ready:
+ if (cfg->has_lane_rst)
+ reset_control_assert(qphy->lane_rst);
+err_lane_rst:
+ qcom_qmp_phy_com_exit(qmp);
+err_com_init:
+ while (--i >= 0)
+ clk_disable_unprepare(qmp->clks[i]);
+
+ return ret;
+}
+
+static int qcom_qmp_phy_exit(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ int i = cfg->num_clks;
+
+ /* PHY reset */
+ qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+
+ /* stop SerDes and Phy-Coding-Sublayer */
+ qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+ /* Put PHY into POWER DOWN state: active low */
+ qphy_clrbits(qphy->pcs, QPHY_POWER_DOWN_CONTROL,
+ cfg->pwrdn_ctrl);
+
+ if (cfg->has_lane_rst)
+ reset_control_assert(qphy->lane_rst);
+
+ qcom_qmp_phy_com_exit(qmp);
+
+ while (--i >= 0)
+ clk_disable_unprepare(qmp->clks[i]);
+
+ return 0;
+}
+
+static int qcom_qmp_phy_vreg_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int num = qmp->cfg->num_vregs;
+ int i;
+
+ qmp->vregs = devm_kcalloc(dev, num, sizeof(qmp->vregs), GFP_KERNEL);
+ if (!qmp->vregs)
+ return -ENOMEM;
+
+ for (i = 0; i < num; i++)
+ qmp->vregs[i].supply = qmp->cfg->vreg_list[i];
+
+ return devm_regulator_bulk_get(dev, num, qmp->vregs);
+}
+
+static int qcom_qmp_phy_reset_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int i;
+
+ qmp->resets = devm_kcalloc(dev, qmp->cfg->num_resets,
+ sizeof(*qmp->resets), GFP_KERNEL);
+ if (!qmp->resets)
+ return -ENOMEM;
+
+ for (i = 0; i < qmp->cfg->num_resets; i++) {
+ struct reset_control *rst;
+ const char *name = qmp->cfg->reset_list[i];
+
+ rst = devm_reset_control_get(dev, name);
+ if (IS_ERR(rst)) {
+ dev_err(dev, "failed to get %s reset\n", name);
+ return PTR_ERR(rst);
+ }
+ qmp->resets[i] = rst;
+ }
+
+ return 0;
+}
+
+static int qcom_qmp_phy_clk_init(struct device *dev)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ int ret, i;
+
+ qmp->clks = devm_kcalloc(dev, qmp->cfg->num_clks,
+ sizeof(*qmp->clks), GFP_KERNEL);
+ if (!qmp->clks)
+ return -ENOMEM;
+
+ for (i = 0; i < qmp->cfg->num_clks; i++) {
+ struct clk *_clk;
+ const char *name = qmp->cfg->clk_list[i];
+
+ _clk = devm_clk_get(dev, name);
+ if (IS_ERR(_clk)) {
+ ret = PTR_ERR(_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get %s clk, %d\n",
+ name, ret);
+ return ret;
+ }
+ qmp->clks[i] = _clk;
+ }
+
+ return 0;
+}
+
+/*
+ * Register a fixed rate pipe clock.
+ *
+ * The <s>_pipe_clksrc generated by PHY goes to the GCC that gate
+ * controls it. The <s>_pipe_clk coming out of the GCC is requested
+ * by the PHY driver for its operations.
+ * We register the <s>_pipe_clksrc here. The gcc driver takes care
+ * of assigning this <s>_pipe_clksrc as parent to <s>_pipe_clk.
+ * Below picture shows this relationship.
+ *
+ * +---------------+
+ * | PHY block |<<---------------------------------------+
+ * | | |
+ * | +-------+ | +-----+ |
+ * I/P---^-->| PLL |---^--->pipe_clksrc--->| GCC |--->pipe_clk---+
+ * clk | +-------+ | +-----+
+ * +---------------+
+ */
+static int phy_pipe_clk_register(struct qcom_qmp *qmp, int id)
+{
+ char name[24];
+ struct clk_fixed_rate *fixed;
+ struct clk_init_data init = { };
+
+ switch (qmp->cfg->type) {
+ case PHY_TYPE_USB3:
+ snprintf(name, sizeof(name), "usb3_phy_pipe_clk_src");
+ break;
+ case PHY_TYPE_PCIE:
+ snprintf(name, sizeof(name), "pcie_%d_pipe_clk_src", id);
+ break;
+ default:
+ /* not all phys register pipe clocks, so return success */
+ return 0;
+ }
+
+ fixed = devm_kzalloc(qmp->dev, sizeof(*fixed), GFP_KERNEL);
+ if (!fixed)
+ return -ENOMEM;
+
+ init.name = name;
+ init.ops = &clk_fixed_rate_ops;
+
+ /* controllers using QMP phys use 125MHz pipe clock interface */
+ fixed->fixed_rate = 125000000;
+ fixed->hw.init = &init;
+
+ return devm_clk_hw_register(qmp->dev, &fixed->hw);
+}
+
+static const struct phy_ops qcom_qmp_phy_gen_ops = {
+ .init = qcom_qmp_phy_init,
+ .exit = qcom_qmp_phy_exit,
+ .power_on = qcom_qmp_phy_poweron,
+ .power_off = qcom_qmp_phy_poweroff,
+ .owner = THIS_MODULE,
+};
+
+static
+int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
+{
+ struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ struct phy *generic_phy;
+ struct qmp_phy *qphy;
+ char prop_name[MAX_PROP_NAME];
+ int ret;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ /*
+ * Get memory resources for each phy lane:
+ * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2.
+ */
+ qphy->tx = of_iomap(np, 0);
+ if (IS_ERR(qphy->tx))
+ return PTR_ERR(qphy->tx);
+
+ qphy->rx = of_iomap(np, 1);
+ if (IS_ERR(qphy->rx))
+ return PTR_ERR(qphy->rx);
+
+ qphy->pcs = of_iomap(np, 2);
+ if (IS_ERR(qphy->pcs))
+ return PTR_ERR(qphy->pcs);
+
+ /*
+ * Get PHY's Pipe clock, if any. USB3 and PCIe are PIPE3
+ * based phys, so they essentially have pipe clock. So,
+ * we return error in case phy is USB3 or PIPE type.
+ * Otherwise, we initialize pipe clock to NULL for
+ * all phys that don't need this.
+ */
+ snprintf(prop_name, sizeof(prop_name), "pipe%d", id);
+ qphy->pipe_clk = of_clk_get_by_name(np, prop_name);
+ if (IS_ERR(qphy->pipe_clk)) {
+ if (qmp->cfg->type == PHY_TYPE_PCIE ||
+ qmp->cfg->type == PHY_TYPE_USB3) {
+ ret = PTR_ERR(qphy->pipe_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev,
+ "failed to get lane%d pipe_clk, %d\n",
+ id, ret);
+ return ret;
+ }
+ qphy->pipe_clk = NULL;
+ }
+
+ /* Get lane reset, if any */
+ if (qmp->cfg->has_lane_rst) {
+ snprintf(prop_name, sizeof(prop_name), "lane%d", id);
+ qphy->lane_rst = of_reset_control_get(np, prop_name);
+ if (IS_ERR(qphy->lane_rst)) {
+ dev_err(dev, "failed to get lane%d reset\n", id);
+ return PTR_ERR(qphy->lane_rst);
+ }
+ }
+
+ generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops);
+ if (IS_ERR(generic_phy)) {
+ ret = PTR_ERR(generic_phy);
+ dev_err(dev, "failed to create qphy %d\n", ret);
+ return ret;
+ }
+
+ qphy->phy = generic_phy;
+ qphy->index = id;
+ qphy->qmp = qmp;
+ qmp->phys[id] = qphy;
+ phy_set_drvdata(generic_phy, qphy);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
+ {
+ .compatible = "qcom,msm8996-qmp-pcie-phy",
+ .data = &msm8996_pciephy_cfg,
+ }, {
+ .compatible = "qcom,msm8996-qmp-usb3-phy",
+ .data = &msm8996_usb3phy_cfg,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_qmp_phy_of_match_table);
+
+static int qcom_qmp_phy_probe(struct platform_device *pdev)
+{
+ struct qcom_qmp *qmp;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct device_node *child;
+ struct phy_provider *phy_provider;
+ void __iomem *base;
+ int num, id;
+ int ret;
+
+ qmp = devm_kzalloc(dev, sizeof(*qmp), GFP_KERNEL);
+ if (!qmp)
+ return -ENOMEM;
+
+ qmp->dev = dev;
+ dev_set_drvdata(dev, qmp);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ /* per PHY serdes; usually located at base address */
+ qmp->serdes = base;
+
+ mutex_init(&qmp->phy_mutex);
+
+ /* Get the specific init parameters of QMP phy */
+ qmp->cfg = of_device_get_match_data(dev);
+
+ ret = qcom_qmp_phy_clk_init(dev);
+ if (ret)
+ return ret;
+
+ ret = qcom_qmp_phy_reset_init(dev);
+ if (ret)
+ return ret;
+
+ ret = qcom_qmp_phy_vreg_init(dev);
+ if (ret) {
+ dev_err(dev, "failed to get regulator supplies\n");
+ return ret;
+ }
+
+ num = of_get_available_child_count(dev->of_node);
+ /* do we have a rogue child node ? */
+ if (num > qmp->cfg->nlanes)
+ return -EINVAL;
+
+ qmp->phys = devm_kcalloc(dev, num, sizeof(*qmp->phys), GFP_KERNEL);
+ if (!qmp->phys)
+ return -ENOMEM;
+
+ id = 0;
+ for_each_available_child_of_node(dev->of_node, child) {
+ /* Create per-lane phy */
+ ret = qcom_qmp_phy_create(dev, child, id);
+ if (ret) {
+ dev_err(dev, "failed to create lane%d phy, %d\n",
+ id, ret);
+ return ret;
+ }
+
+ /*
+ * Register the pipe clock provided by phy.
+ * See function description to see details of this pipe clock.
+ */
+ ret = phy_pipe_clk_register(qmp, id);
+ if (ret) {
+ dev_err(qmp->dev,
+ "failed to register pipe clock source\n");
+ return ret;
+ }
+ id++;
+ }
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (!IS_ERR(phy_provider))
+ dev_info(dev, "Registered Qcom-QMP phy\n");
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qcom_qmp_phy_driver = {
+ .probe = qcom_qmp_phy_probe,
+ .driver = {
+ .name = "qcom-qmp-phy",
+ .of_match_table = qcom_qmp_phy_of_match_table,
+ },
+};
+
+module_platform_driver(qcom_qmp_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QMP PHY driver");
+MODULE_LICENSE("GPL v2");
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH V7 3/4] dt-bindings: phy: Add support for QMP phy
From: Vivek Gautam @ 2017-04-05 12:32 UTC (permalink / raw)
To: kishon, robh+dt
Cc: mark.rutland, devicetree, linux-arm-msm, linux-usb, sboyd,
linux-kernel, bjorn.andersson, srinivas.kandagatla, Vivek Gautam,
linux-arm-kernel
In-Reply-To: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org>
Qualcomm chipsets have QMP phy controller that provides
support to a number of controller, viz. PCIe, UFS, and USB.
Adding dt binding information for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Changes since v6:
- none.
Changes since v5:
- Added Rob's 'Ack' for the new child nodes based bindings.
- Dropped leading 0 from the address in 'reg' property.
- Fixed '@xyz' part of the node name with correct address.
Changes since v4:
- Added bindings for child nodes. Each phy lane is represented by child
node with its own register space (for tx, rx and pcs blocks), and clocks
and resets for power control facility.
- Removed register space and lane offsets for tx, rx and pcs blocks from
qmp phy node.
- #phy-cells is now part of each child node and thus must be 0.
- Added information on list of mandatory clocks and resets for each phy.
Changes since v3:
- Added #clock-cells = <1>, indicating that phy is a clock provider.
Changes since v2:
- Removed binding for "ref_clk_src" since we don't request this
clock in the driver.
- Addressed s/ref_clk/ref. Don't need to add '_clk' suffix to clock names.
- Using 'phy' for the node name.
Changes since v1:
- New patch, forked out of the original driver patch:
"phy: qcom-qmp: new qmp phy driver for qcom-chipsets"
- Added 'Acked-by' from Rob.
- Updated bindings to include mem resource as a list of
offset - length pair for serdes block and for each lane.
- Added a new binding for 'lane-offsets' that contains offsets
to tx, rx and pcs blocks from each lane base address.
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 106 +++++++++++++++++++++
1 file changed, 106 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
new file mode 100644
index 000000000000..e11c563a65ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
@@ -0,0 +1,106 @@
+Qualcomm QMP PHY controller
+===========================
+
+QMP phy controller supports physical layer functionality for a number of
+controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
+
+Required properties:
+ - compatible: compatible list, contains:
+ "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
+ "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
+
+ - reg: offset and length of register set for PHY's common serdes block.
+
+ - #clock-cells: must be 1
+ - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
+ interface (for pipe based PHYs). These clock are then gate-controlled
+ by gcc.
+ - #address-cells: must be 1
+ - #size-cells: must be 1
+ - ranges: must be present
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: "cfg_ahb" for phy config clock,
+ "aux" for phy aux clock,
+ "ref" for 19.2 MHz ref clk,
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+ For "qcom,msm8996-qmp-usb3-phy" must contain:
+ "aux", "cfg_ahb", "ref".
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: "phy" for reset of phy block,
+ "common" for phy common block reset,
+ "cfg" for phy's ahb cfg block reset (Optional).
+ For "qcom,msm8996-qmp-pcie-phy" must contain:
+ "phy", "common", "cfg".
+ For "qcom,msm8996-qmp-usb3-phy" must contain
+ "phy", "common".
+
+ - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+Optional properties:
+ - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
+ pll block.
+
+Required nodes:
+ - Each device node of QMP phy is required to have as many child nodes as
+ the number of lanes the PHY has.
+
+Required properties for child node:
+ - reg: list of offset and length pairs of register sets for PHY blocks -
+ tx, rx and pcs.
+
+ - #phy-cells: must be 0
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: Must contain following for pcie and usb qmp phys:
+ "pipe<lane-number>" for pipe clock specific to each lane.
+
+ - resets: a list of phandles and reset controller specifier pairs,
+ one for each entry in reset-names.
+ - reset-names: Must contain following for pcie qmp phys:
+ "lane<lane-number>" for reset specific to each lane.
+
+Example:
+ phy@34000 {
+ compatible = "qcom,msm8996-qmp-pcie-phy";
+ reg = <0x34000 0x488>;
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+ <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_CLKREF_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref";
+
+ vdda-phy-supply = <&pm8994_l28>;
+ vdda-pll-supply = <&pm8994_l12>;
+
+ resets = <&gcc GCC_PCIE_PHY_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_BCR>,
+ <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
+ reset-names = "phy", "common", "cfg";
+
+ pciephy_0: lane@35000 {
+ reg = <0x35000 0x130>,
+ <0x35200 0x200>,
+ <0x35400 0x1dc>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ clock-names = "pipe0";
+ resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+ reset-names = "lane0";
+ };
+
+ pciephy_1: lane@36000 {
+ ...
+ ...
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH V7 2/4] phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips
From: Vivek Gautam @ 2017-04-05 12:32 UTC (permalink / raw)
To: kishon, robh+dt
Cc: mark.rutland, devicetree, linux-arm-msm, linux-usb, sboyd,
linux-kernel, bjorn.andersson, srinivas.kandagatla, Vivek Gautam,
linux-arm-kernel
In-Reply-To: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org>
PHY transceiver driver for QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller present on
Qualcomm chipsets.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
---
Changes since v6:
- Dropped 'vdd-phy' from list of regulators.
- Rebased on phy/next and *not* including phy grouping series.
Changes since v5:
- Rebased on top of phy grouping series. So the driver now sits in
drivers/phy/qualcomm/
- Removed instances of readl_relaxed() and writel_relaxed(), and using
readl() and writel() instead.
- Replaced regulator handling with regulator_bulk() apis, so that
qusb2_phy_toggle_power() method is completely dropped.
- Removed memory barriers from the driver. Instead, using readl() over
the register to ensure that the write is through to the device.
- Fixed nits about return statement from probe() and qusb2_phy_poweron().
Changes since v4:
- Updated the copyright year to 2017.
- Removed unnecessary of_match_ptr() cast for the match table,
since the driver is compiled for CONFIG_OF.
Changes since v3:
- Added 'Reviewed-by' from Stephen.
- Fixed debug message for qusb2_phy_set_tune2_param().
- Replaced devm_reset_control_get() with devm_reset_control_get_by_index()
since we are requesting only one reset.
- Updated devm_nvmem_cell_get() with a NULL cell id.
- Made error labels more idiomatic.
- Refactored qusb2_setbits() and qusb2_clrbits() a little bit to accept
base address and register offset as two separate arguments.
Changes since v2:
- Removed selecting 'RESET_CONTROLLER' config.
- Added error handling for clk_prepare_enable paths.
- Removed explicitly setting ref_clk rate to 19.2 MHz. Don't need to
do that since 'xo' is modeled as parent to this clock.
- Removed 'ref_clk_src' handling. Driver doesn't need to request and
handle this clock.
- Moved nvmem_cell_get() to probe function.
- Simplified phy pll status handling.
- Using of_device_get_match_data() to get match data.
- Uniformly using lowercase for hex numbers.
- Fixed sparse warnings.
- Using shorter variable names in structure and in functions.
- Handling various comment style shortcomings.
Changes since v1:
- removed reference to clk_enabled/pwr_enabled.
- moved clock and regulator enable code to phy_power_on/off() callbacks.
- fixed return on EPROBE_DEFER in qusb2_phy_probe().
- fixed phy create and phy register ordering.
- removed references to non-lkml links from commit message.
- took care of other minor nits.
- Fixed coccinelle warnings -
'PTR_ERR applied after initialization to constant'
- Addressed review comment, regarding qfprom access for tune2 param value.
This driver is now based on qfprom patch[1] that allows byte access now.
drivers/phy/Kconfig | 10 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-qusb2.c | 491 +++++++++++++++++++++++++++++++++++++++++++
3 files changed, 502 insertions(+)
create mode 100644 drivers/phy/phy-qcom-qusb2.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index dc5277ad1b5a..ccc9178e32cd 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -439,6 +439,16 @@ config PHY_STIH407_USB
Enable this support to enable the picoPHY device used by USB2
and USB3 controllers on STMicroelectronics STiH407 SoC families.
+config PHY_QCOM_QUSB2
+ tristate "Qualcomm QUSB2 PHY Driver"
+ depends on OF && (ARCH_QCOM || COMPILE_TEST)
+ select GENERIC_PHY
+ help
+ Enable this to support the HighSpeed QUSB2 PHY transceiver for USB
+ controllers on Qualcomm chips. This driver supports the high-speed
+ PHY which is usually paired with either the ChipIdea or Synopsys DWC3
+ USB IPs on MSM SOCs.
+
config PHY_QCOM_UFS
tristate "Qualcomm UFS PHY driver"
depends on OF && ARCH_QCOM
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index e7b0feb1e125..0375c6a32697 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -50,6 +50,7 @@ obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
+obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
diff --git a/drivers/phy/phy-qcom-qusb2.c b/drivers/phy/phy-qcom-qusb2.c
new file mode 100644
index 000000000000..045b0743a033
--- /dev/null
+++ b/drivers/phy/phy-qcom-qusb2.c
@@ -0,0 +1,491 @@
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#define QUSB2PHY_PLL_TEST 0x04
+#define CLK_REF_SEL BIT(7)
+
+#define QUSB2PHY_PLL_TUNE 0x08
+#define QUSB2PHY_PLL_USER_CTL1 0x0c
+#define QUSB2PHY_PLL_USER_CTL2 0x10
+#define QUSB2PHY_PLL_AUTOPGM_CTL1 0x1c
+#define QUSB2PHY_PLL_PWR_CTRL 0x18
+
+#define QUSB2PHY_PLL_STATUS 0x38
+#define PLL_LOCKED BIT(5)
+
+#define QUSB2PHY_PORT_TUNE1 0x80
+#define QUSB2PHY_PORT_TUNE2 0x84
+#define QUSB2PHY_PORT_TUNE3 0x88
+#define QUSB2PHY_PORT_TUNE4 0x8c
+#define QUSB2PHY_PORT_TUNE5 0x90
+#define QUSB2PHY_PORT_TEST2 0x9c
+
+#define QUSB2PHY_PORT_POWERDOWN 0xb4
+#define CLAMP_N_EN BIT(5)
+#define FREEZIO_N BIT(1)
+#define POWER_DOWN BIT(0)
+
+#define QUSB2PHY_REFCLK_ENABLE BIT(0)
+
+#define PHY_CLK_SCHEME_SEL BIT(0)
+
+struct qusb2_phy_init_tbl {
+ unsigned int offset;
+ unsigned int val;
+};
+#define QUSB2_PHY_INIT_CFG(o, v) \
+ { \
+ .offset = o, \
+ .val = v, \
+ }
+
+static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = {
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE1, 0xf8),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE2, 0xb3),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE3, 0x83),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TUNE4, 0xc0),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PORT_TEST2, 0x14),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f),
+ QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
+};
+
+struct qusb2_phy_cfg {
+ const struct qusb2_phy_init_tbl *tbl;
+ /* number of entries in the table */
+ unsigned int tbl_num;
+ /* offset to PHY_CLK_SCHEME register in TCSR map */
+ unsigned int clk_scheme_offset;
+};
+
+static const struct qusb2_phy_cfg msm8996_phy_cfg = {
+ .tbl = msm8996_init_tbl,
+ .tbl_num = ARRAY_SIZE(msm8996_init_tbl),
+};
+
+static const char * const qusb2_phy_vreg_names[] = {
+ "vdda-pll", "vdda-phy-dpdm",
+};
+#define QUSB2_NUM_VREGS ARRAY_SIZE(qusb2_phy_vreg_names)
+
+/**
+ * struct qusb2_phy - structure holding qusb2 phy attributes
+ *
+ * @phy: generic phy
+ * @base: iomapped memory space for qubs2 phy
+ *
+ * @cfg_ahb_clk: AHB2PHY interface clock
+ * @ref_clk: phy reference clock
+ * @iface_clk: phy interface clock
+ * @phy_reset: phy reset control
+ * @vregs: regulator supplies bulk data
+ *
+ * @tcsr: TCSR syscon register map
+ * @cell: nvmem cell containing phy tuning value
+ *
+ * @cfg: phy config data
+ * @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme
+ */
+struct qusb2_phy {
+ struct phy *phy;
+ void __iomem *base;
+
+ struct clk *cfg_ahb_clk;
+ struct clk *ref_clk;
+ struct clk *iface_clk;
+ struct reset_control *phy_reset;
+ struct regulator_bulk_data vregs[QUSB2_NUM_VREGS];
+
+ struct regmap *tcsr;
+ struct nvmem_cell *cell;
+
+ const struct qusb2_phy_cfg *cfg;
+ bool has_se_clk_scheme;
+};
+
+static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg |= val;
+ writel(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl(base + offset);
+}
+
+static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val)
+{
+ u32 reg;
+
+ reg = readl(base + offset);
+ reg &= ~val;
+ writel(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl(base + offset);
+}
+
+static inline void qcom_qusb2_phy_configure(void __iomem *base,
+ const struct qusb2_phy_init_tbl tbl[],
+ int num)
+{
+ int i;
+
+ for (i = 0; i < num; i++)
+ writel(tbl[i].val, base + tbl[i].offset);
+}
+
+/*
+ * Fetches HS Tx tuning value from nvmem and sets the
+ * QUSB2PHY_PORT_TUNE2 register.
+ * For error case, skip setting the value and use the default value.
+ */
+static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
+{
+ struct device *dev = &qphy->phy->dev;
+ u8 *val;
+
+ /*
+ * Read efuse register having TUNE2 parameter's high nibble.
+ * If efuse register shows value as 0x0, or if we fail to find
+ * a valid efuse register settings, then use default value
+ * as 0xB for high nibble that we have already set while
+ * configuring phy.
+ */
+ val = nvmem_cell_read(qphy->cell, NULL);
+ if (IS_ERR(val) || !val[0]) {
+ dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
+ return;
+ }
+
+ /* Fused TUNE2 value is the higher nibble only */
+ qusb2_setbits(qphy->base, QUSB2PHY_PORT_TUNE2, val[0] << 0x4);
+}
+
+static int qusb2_phy_poweron(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+ int num = ARRAY_SIZE(qphy->vregs);
+ int ret;
+
+ dev_vdbg(&phy->dev, "%s(): Powering-on QUSB2 phy\n", __func__);
+
+ /* turn on regulator supplies */
+ ret = regulator_bulk_enable(num, qphy->vregs);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(qphy->iface_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret);
+ regulator_bulk_disable(num, qphy->vregs);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int qusb2_phy_poweroff(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+ clk_disable_unprepare(qphy->iface_clk);
+
+ regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
+ return 0;
+}
+
+static int qusb2_phy_init(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+ unsigned int val;
+ unsigned int clk_scheme;
+ int ret;
+
+ dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
+
+ /* enable ahb interface clock to program phy */
+ ret = clk_prepare_enable(qphy->cfg_ahb_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+ return ret;
+ }
+
+ /* Perform phy reset */
+ ret = reset_control_assert(qphy->phy_reset);
+ if (ret) {
+ dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
+ goto disable_ahb_clk;
+ }
+
+ /* 100 us delay to keep PHY in reset mode */
+ usleep_range(100, 150);
+
+ ret = reset_control_deassert(qphy->phy_reset);
+ if (ret) {
+ dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
+ goto disable_ahb_clk;
+ }
+
+ /* Disable the PHY */
+ qusb2_setbits(qphy->base, QUSB2PHY_PORT_POWERDOWN,
+ CLAMP_N_EN | FREEZIO_N | POWER_DOWN);
+
+ /* save reset value to override reference clock scheme later */
+ val = readl(qphy->base + QUSB2PHY_PLL_TEST);
+
+ qcom_qusb2_phy_configure(qphy->base, qphy->cfg->tbl,
+ qphy->cfg->tbl_num);
+
+ /* Set efuse value for tuning the PHY */
+ qusb2_phy_set_tune2_param(qphy);
+
+ /* Enable the PHY */
+ qusb2_clrbits(qphy->base, QUSB2PHY_PORT_POWERDOWN, POWER_DOWN);
+
+ /* Required to get phy pll lock successfully */
+ usleep_range(150, 160);
+
+ /* Default is single-ended clock on msm8996 */
+ qphy->has_se_clk_scheme = true;
+ /*
+ * read TCSR_PHY_CLK_SCHEME register to check if single-ended
+ * clock scheme is selected. If yes, then disable differential
+ * ref_clk and use single-ended clock, otherwise use differential
+ * ref_clk only.
+ */
+ if (qphy->tcsr) {
+ ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset,
+ &clk_scheme);
+ if (ret) {
+ dev_err(&phy->dev, "failed to read clk scheme reg\n");
+ goto assert_phy_reset;
+ }
+
+ /* is it a differential clock scheme ? */
+ if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) {
+ dev_vdbg(&phy->dev, "%s(): select differential clk\n",
+ __func__);
+ qphy->has_se_clk_scheme = false;
+ } else {
+ dev_vdbg(&phy->dev, "%s(): select single-ended clk\n",
+ __func__);
+ }
+ }
+
+ if (!qphy->has_se_clk_scheme) {
+ val &= ~CLK_REF_SEL;
+ ret = clk_prepare_enable(qphy->ref_clk);
+ if (ret) {
+ dev_err(&phy->dev, "failed to enable ref clk, %d\n",
+ ret);
+ goto assert_phy_reset;
+ }
+ } else {
+ val |= CLK_REF_SEL;
+ }
+
+ writel(val, qphy->base + QUSB2PHY_PLL_TEST);
+
+ /* ensure above write is through */
+ readl(qphy->base + QUSB2PHY_PLL_TEST);
+
+ /* Required to get phy pll lock successfully */
+ usleep_range(100, 110);
+
+ val = readb(qphy->base + QUSB2PHY_PLL_STATUS);
+ if (!(val & PLL_LOCKED)) {
+ dev_err(&phy->dev,
+ "QUSB2PHY pll lock failed: status reg = %x\n", val);
+ ret = -EBUSY;
+ goto disable_ref_clk;
+ }
+
+ return 0;
+
+disable_ref_clk:
+ if (!qphy->has_se_clk_scheme)
+ clk_disable_unprepare(qphy->ref_clk);
+assert_phy_reset:
+ reset_control_assert(qphy->phy_reset);
+disable_ahb_clk:
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+ return ret;
+}
+
+static int qusb2_phy_exit(struct phy *phy)
+{
+ struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+ /* Disable the PHY */
+ qusb2_setbits(qphy->base, QUSB2PHY_PORT_POWERDOWN,
+ CLAMP_N_EN | FREEZIO_N | POWER_DOWN);
+
+ if (!qphy->has_se_clk_scheme)
+ clk_disable_unprepare(qphy->ref_clk);
+
+ reset_control_assert(qphy->phy_reset);
+
+ clk_disable_unprepare(qphy->cfg_ahb_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qusb2_phy_gen_ops = {
+ .init = qusb2_phy_init,
+ .exit = qusb2_phy_exit,
+ .power_on = qusb2_phy_poweron,
+ .power_off = qusb2_phy_poweroff,
+ .owner = THIS_MODULE,
+};
+
+static const struct of_device_id qusb2_phy_of_match_table[] = {
+ {
+ .compatible = "qcom,msm8996-qusb2-phy",
+ .data = &msm8996_phy_cfg,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table);
+
+static int qusb2_phy_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct qusb2_phy *qphy;
+ struct phy_provider *phy_provider;
+ struct phy *generic_phy;
+ struct resource *res;
+ int ret, i;
+ int num;
+
+ qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+ if (!qphy)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ qphy->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(qphy->base))
+ return PTR_ERR(qphy->base);
+
+ qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb");
+ if (IS_ERR(qphy->cfg_ahb_clk)) {
+ ret = PTR_ERR(qphy->cfg_ahb_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get cfg ahb clk, %d\n", ret);
+ return ret;
+ }
+
+ qphy->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(qphy->ref_clk)) {
+ ret = PTR_ERR(qphy->ref_clk);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "failed to get ref clk, %d\n", ret);
+ return ret;
+ }
+
+ qphy->iface_clk = devm_clk_get(dev, "iface");
+ if (IS_ERR(qphy->iface_clk)) {
+ ret = PTR_ERR(qphy->iface_clk);
+ if (ret == -EPROBE_DEFER)
+ return ret;
+ qphy->iface_clk = NULL;
+ dev_dbg(dev, "failed to get iface clk, %d\n", ret);
+ }
+
+ qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0);
+ if (IS_ERR(qphy->phy_reset)) {
+ dev_err(dev, "failed to get phy core reset\n");
+ return PTR_ERR(qphy->phy_reset);
+ }
+
+ num = ARRAY_SIZE(qphy->vregs);
+ for (i = 0; i < num; i++)
+ qphy->vregs[i].supply = qusb2_phy_vreg_names[i];
+
+ ret = devm_regulator_bulk_get(dev, num, qphy->vregs);
+ if (ret) {
+ dev_err(dev, "failed to get regulator supplies\n");
+ return ret;
+ }
+
+ /* Get the specific init parameters of QMP phy */
+ qphy->cfg = of_device_get_match_data(dev);
+
+ qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "qcom,tcsr-syscon");
+ if (IS_ERR(qphy->tcsr)) {
+ dev_dbg(dev, "failed to lookup TCSR regmap\n");
+ qphy->tcsr = NULL;
+ }
+
+ qphy->cell = devm_nvmem_cell_get(dev, NULL);
+ if (IS_ERR(qphy->cell)) {
+ if (PTR_ERR(qphy->cell) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ qphy->cell = NULL;
+ dev_dbg(dev, "failed to lookup tune2 hstx trim value\n");
+ }
+
+ generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops);
+ if (IS_ERR(generic_phy)) {
+ ret = PTR_ERR(generic_phy);
+ dev_err(dev, "failed to create phy, %d\n", ret);
+ return ret;
+ }
+ qphy->phy = generic_phy;
+
+ dev_set_drvdata(dev, qphy);
+ phy_set_drvdata(generic_phy, qphy);
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (!IS_ERR(phy_provider))
+ dev_info(dev, "Registered Qcom-QUSB2 phy\n");
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qusb2_phy_driver = {
+ .probe = qusb2_phy_probe,
+ .driver = {
+ .name = "qcom-qusb2-phy",
+ .of_match_table = qusb2_phy_of_match_table,
+ },
+};
+
+module_platform_driver(qusb2_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver");
+MODULE_LICENSE("GPL v2");
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH V7 1/4] dt-bindings: phy: Add support for QUSB2 phy
From: Vivek Gautam @ 2017-04-05 12:32 UTC (permalink / raw)
To: kishon, robh+dt
Cc: mark.rutland, devicetree, linux-arm-msm, linux-usb, sboyd,
linux-kernel, bjorn.andersson, srinivas.kandagatla, Vivek Gautam,
linux-arm-kernel
In-Reply-To: <1491395558-16902-1-git-send-email-vivek.gautam@codeaurora.org>
Qualcomm chipsets have QUSB2 phy controller that provides
HighSpeed functionality for DWC3 controller.
Adding dt binding information for the same.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Changes since v6:
- Dropped 'vdd-phy-supply' that used pm8994_s2 regulator, from bindings.
As Stephen said, the pm8994_s2 is a 'corner' regulator and it shouldn't
be right to put it as a regulator supply.
Work is in progress to handle these sort of power supplies.
Changes since v5:
- Removed leading 0 from the address in 'reg' property.
Changes since v4:
- None.
Changes since v3:
- Added 'Acked-by' from Rob.
- Removed 'reset-names' and 'nvmem-cell-names' from the bindings
since we use only one cell.
Changes since v2:
- Removed binding for "ref_clk_src" since we don't request this
clock in the driver.
- Addressed s/vdda-phy-dpdm/vdda-phy-dpdm-supply.
- Addressed s/ref_clk/ref. Don't need to add '_clk' suffix to clock names.
- Addressed s/tune2_hstx_trim_efuse/tune2_hstx_trim. Don't need to add
'efuse' suffix to nvmem cell.
- Addressed s/qusb2phy/phy for the node name.
Changes since v1:
- New patch, forked out of the original driver patch:
"phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips"
- Updated dt bindings to remove 'hstx-trim-bit-offset' and
'hstx-trim-bit-len' bindings.
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
new file mode 100644
index 000000000000..aa0fcb05acb3
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -0,0 +1,43 @@
+Qualcomm QUSB2 phy controller
+=============================
+
+QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+Required properties:
+ - compatible: compatible list, contains "qcom,msm8996-qusb2-phy".
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a list of phandles and clock-specifier pairs,
+ one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+ "ref" for 19.2 MHz ref clk,
+ "iface" for phy interface clock (Optional).
+
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+ - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+ - resets: Phandle to reset to phy block.
+
+Optional properties:
+ - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
+ tuning parameter value for qusb2 phy.
+
+ - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
+
+Example:
+ hsusb_phy: phy@7411000 {
+ compatible = "qcom,msm8996-qusb2-phy";
+ reg = <0x7411000 0x180>;
+ #phy-cells = <0>;
+
+ clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+ <&gcc GCC_RX1_USB2_CLKREF_CLK>,
+ clock-names = "cfg_ahb", "ref";
+
+ vdda-pll-supply = <&pm8994_l12>;
+ vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+ resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+ nvmem-cells = <&qusb2p_hstx_trim>;
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH V7 0/4] phy: USB and PCIe phy drivers for Qcom chipsets
From: Vivek Gautam @ 2017-04-05 12:32 UTC (permalink / raw)
To: kishon, robh+dt
Cc: mark.rutland, devicetree, linux-arm-msm, linux-usb, sboyd,
linux-kernel, bjorn.andersson, srinivas.kandagatla, Vivek Gautam,
linux-arm-kernel
This patch series adds couple of PHY drivers for Qualcomm chipsets.
a) qcom-qusb2 phy driver: that provides High Speed USB functionality.
b) qcom-qmp phy driver: that is a combo phy providing support for
USB3, PCIe, UFS and few other controllers.
The patches are based on next branch of linux-phy tree.
These patches have been tested on Dragon board db820c hardware with
required set of dt patches and the patches to get rpm up on msm8996.
Couple of other patches [1, 2] fixing DMA config for XHCI are also
pulled in for testing.
A branch based on torvald's master is available in github [3].
Changes since v6:
- Rebased on phy/next and *not* including phy grouping series[4].
- qusb2-phy: addressed Stephen's comment.
- Dropped pm8994_s2 corner regulator from QUSB2 phy bindings.
- qmp-phy: none on functionality side.
Changes since v5:
- Addressed review comments from Bjorn:
- Removed instances of readl/wirtel_relaxed calls from the drivers.
Instead, using simple readl/writel. Inserting a readl after a writel
to ensure the write is through to the device.
- Replaced regulator handling with regulator_bulk_** apis. This helps
in cutting down a lot of regulator handling code.
- Fixed minor return statements.
Changes since v4:
- Addressed comment to add child nodes for qmp phy driver. Each phy lane
now has a separate child node under the main qmp node.
- Modified the clock and reset initialization and enable methods.
Different phys - pcie, usb and later ufs, have varying number of clocks
and resets that are mandatory. So adding provision for clocks and reset
lists helps in requesting all mandatory resources for individual phys
and handle their failure cases accordingly.
Changes since v3:
- Addressed review comments given by Rob and Stephen for qusb2 phy
and qmp phy bindings respectively.
- Addressed review comments given by Stephen and Bjorn for qmp phy driver.
Changes since v2:
- Addressed review comments given by Rob and Stephen for bindings.
- Addressed the review comments given by Stephen for the qusb2 and qmp
phy drivers.
Changes since v1:
- Moved device tree binding documentation to separate patches, as suggested
by Rob.
- Addressed review comment regarding qfprom accesses by qusb2 phy driver,
given by Rob.
- Addressed review comments from Kishon.
- Addressed review comments from Srinivas for QMP phy driver.
- Addressed kbuild warning.
Please see individual patches for detailed changelogs.
[1] https://patchwork.kernel.org/patch/9567767/
[2] https://patchwork.kernel.org/patch/9567779/
[3] https://github.com/vivekgautam1/linux/tree/linux-v4.11-rc5-qmp-phy-db820c
[4] https://lkml.org/lkml/2017/3/20/407
Vivek Gautam (4):
dt-bindings: phy: Add support for QUSB2 phy
phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips
dt-bindings: phy: Add support for QMP phy
phy: qcom-qmp: new qmp phy driver for qcom-chipsets
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 106 ++
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 43 +
drivers/phy/Kconfig | 18 +
drivers/phy/Makefile | 2 +
drivers/phy/phy-qcom-qmp.c | 1153 ++++++++++++++++++++
drivers/phy/phy-qcom-qusb2.c | 491 +++++++++
6 files changed, 1813 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
create mode 100644 Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
create mode 100644 drivers/phy/phy-qcom-qmp.c
create mode 100644 drivers/phy/phy-qcom-qusb2.c
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* Re: [PATCH v2] i2c/muxes/i2c-mux-ltc4306: LTC4306 and LTC4305 I2C multiplexer/switch
From: Michael Hennerich @ 2017-04-05 12:21 UTC (permalink / raw)
To: Peter Rosin, wsa-z923LK4zBo2bacvFa/9K2g,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linus.walleij-QSEj5FYQhm4dnm+yROfE0A
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-gpio-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
In-Reply-To: <b5838bae-8108-1a0e-5234-d14cb5e95e52-koto5C5qi+TLoDKTGw+V6w@public.gmane.org>
On 04.04.2017 11:28, Peter Rosin wrote:
> *snip* *snip*
>
>>>> +static int ltc4306_gpio_get(struct gpio_chip *chip, unsigned int offset)
>>>> +{
>>>> + struct ltc4306 *data = gpiochip_get_data(chip);
>>>> + int ret = 0;
>>>> +
>>>> + if (gpiochip_line_is_open_drain(chip, offset) ||
>>>> + (data->regs[LTC_REG_MODE] & BIT(7 - offset))) {
>>>
>>> I wonder about this open-coded register cache. So, gpio people, is there
>>> a guarantee from gpiolib that only one gpio_chip operation is in flight
>>> concurrently? Because I don't see any evidence of that. With that in
>>> mind, I think some locking is needed?
>>
>> I thought there is a per chip mutex in the gpiolib. But I can't find
>> anything like this either. Since these two gpios can be used from
>> different internal or external users. The locking seem to be needed.
>>
>> This gets us back to the regmap option. I did a quick grep, and 9 out of
>> 205 drivers using regmap i2c, also use i2c_smbus... concurrently.
>>
>> grep -Rl regmap_init_i2c ./drivers | xargs grep -l i2c_smbus_ | grep "\.c"
>>
>> Mostly to work around non uniform transfer layouts.
>
> I see three options.
>
> 1. Go with regmap and convert to mux-locked. Then the unlocked i2c-xfer
> becomes an ordinary i2c-xfer (or smbus, whatever). This will result in
> the cleanest code.
ok - you convinced me.
>
> 2. Go with regmap and stay parent-locked. Then hook into the regmap
> locking as is done in one of the drivers that have worked around similar
> problems with regmap and parent-locked i2c-mux interactions:
>
> drivers/media/dvb-frontends/rtl2830.c
> drivers/media/dvb-frontends/m88ds3103.c
>
> This will probably work, but you'd need to add a number of extra helper
> functions.
>
> 3. Exclude register 3 from regmap and only use regmap for the other
> registers. This will be a bit ugly and ad-hoc, will need clear comments
> on what is going on and why it is safe etc. And I want to see it before
> I accept it. And it might not be my call to begin with, because TBH, it
> sounds a bit disgusting...
>
>> I'll check with Mark Brown on this topic.
>
> Ok, might be a good idea...
>
>>>> +
>>>> +add_adapter_failed:
>>>> + i2c_mux_del_adapters(muxc);
>>>> +gpio_default:
>>>> + gpiod_direction_input(data->en_gpio);
>>>
>>> This was actually not what I had in mind when I asked about it in v1, and
>>> this looks a bit strange. You have no way of knowing if the pin was
>>> configured as input when probe was called, and I don't see code like this
>>> all over the place. Maybe it's is ok to not disable the chip over
>>> suspend/resume, I was just asking because it looked a bit strange to grab
>>> a pin and then forget about it. Now that I think about it some more, it's
>>> probably ok to do just that since it is perhaps not possible to make the
>>> chip draw less power by deasserting enable, but what do I know?
>>
>> GPIOs are assumed by default inputs. So if you want to undo the actions
>> in probe. The logical consequence is to move them back to inputs, and
>> let the external PULL-UP or PULL-DOWN on the ENABLE decide what happens.
>> I would also prefer to leave it enabled, so that the GPIOs can retain
>
> My point is that I do not see any probe functions undoing gpio configs.
> Why bother in this case? Or are other probe functions really doing this?
> I actually didn't check, but I haven't stumbled over it previously and
> at least think I would have noticed...
>
>> it's last state. Well I think the device draws a bit less power when
>> disabled. But we don't support runtime PM anyways.
>
> It might not be safe to reset the gpio pins over a suspend/resume depending
> on what they are used for, so it is probably a bad idea to go there. Sorry
> for bringing the whole issue up and muddying the waters...
I restore the original implementation and also pulse the ENABLE low so
we're always doing a clean reset.
I'll send a new patch shortly.
Thanks!
--
Greetings,
Michael
--
Analog Devices GmbH Otl-Aicher Strasse 60-64 80807 München
Sitz der Gesellschaft München, Registergericht München HRB 40368,
Geschäftsführer: Peter Kolberg, Ali Raza Husain, Eileen Wynne
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v2 3/3] clk: vc5: Add support for IDT VersaClock 5P49V5935
From: Geert Uytterhoeven @ 2017-04-05 12:20 UTC (permalink / raw)
To: Alexey Firago
Cc: Michael Turquette, Stephen Boyd, Rob Herring, Marek Vasut,
linux-clk, devicetree@vger.kernel.org
In-Reply-To: <1491392819-698-4-git-send-email-alexey_firago@mentor.com>
On Wed, Apr 5, 2017 at 1:46 PM, Alexey Firago <alexey_firago@mentor.com> wrote:
> Update IDT VersaClock 5 driver to support 5P49V5935. This chip has
> two clock inputs (internal XTAL or external CLKIN), four fractional
> dividers (FODs) and five clock outputs (four universal clock outputs
> and one reference clock output at OUT0_SELB_I2C).
>
> Current driver supports up to 2 FODs and up to 3 clock outputs. This
> patch sets max number of supported FODs to 4 and max number of supported
> clock outputs to 5.
>
> Signed-off-by: Alexey Firago <alexey_firago@mentor.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* Re: [PATCH V8 1/6] LIBIO: Introduce a generic PIO mapping method
From: zhichang.yuan @ 2017-04-05 12:18 UTC (permalink / raw)
To: kbuild test robot, fengguang.wu
Cc: zhichang.yuan, kbuild-all, catalin.marinas, will.deacon, robh+dt,
frowand.list, bhelgaas, rafael, arnd, linux-arm-kernel,
mark.rutland, brian.starkey, olof, lorenzo.pieralisi, benh,
linux-kernel, linux-acpi, linuxarm, devicetree, linux-pci,
minyard, zourongrong, john.garry, gabriele.paoloni, xuwei5
In-Reply-To: <201704011328.1YdgEHnc%fengguang.wu@intel.com>
Hi,
Thanks for your report!
I am sorry for that!
This issue was caused by missing the '#include <linux/logic_pio.h>' in
logic_pio.c for some architectures where the 'asm-generic/io.h' wasn't been
included.
Will be fixed in the next V9.
Apologized for this!
-Zhichang
On 04/01/2017 01:58 PM, kbuild test robot wrote:
> Hi zhichang.yuan,
>
> [auto build test ERROR on linus/master]
> [also build test ERROR on v4.11-rc4 next-20170331]
> [if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
>
> url: https://github.com/0day-ci/linux/commits/zhichang-yuan/LIBIO-Introduce-a-generic-PIO-mapping-method/20170401-104801
> config: alpha-allyesconfig (attached as .config)
> compiler: alpha-linux-gnu-gcc (Debian 6.1.1-9) 6.1.1 20160705
> reproduce:
> wget https://raw.githubusercontent.com/01org/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
> chmod +x ~/bin/make.cross
> # save the attached .config to linux build tree
> make.cross ARCH=alpha
>
> All error/warnings (new ones prefixed by >>):
>
>>> lib/logic_pio.c:32:50: error: 'PIO_MAX_SECT' undeclared here (not in a function)
> static struct logic_pio_root logic_pio_root_list[PIO_MAX_SECT] = {
> ^~~~~~~~~~~~
>>> lib/logic_pio.c:39:3: error: 'PIO_CPU_MMIO' undeclared here (not in a function)
> [PIO_CPU_MMIO ... PIO_INDIRECT - 1] = {
> ^~~~~~~~~~~~
>>> lib/logic_pio.c:39:20: error: 'PIO_INDIRECT' undeclared here (not in a function)
> [PIO_CPU_MMIO ... PIO_INDIRECT - 1] = {
> ^~~~~~~~~~~~
>>> lib/logic_pio.c:39:3: error: array index in initializer not of integer type
> [PIO_CPU_MMIO ... PIO_INDIRECT - 1] = {
> ^~~~~~~~~~~~
> lib/logic_pio.c:39:3: note: (near initialization for 'logic_pio_root_list')
>>> lib/logic_pio.c:40:3: error: field name not in record or union initializer
> .sec_head = LIST_HEAD_INIT(logic_pio_root_list[PIO_CPU_MMIO].sec_head),
> ^
> lib/logic_pio.c:40:3: note: (near initialization for 'logic_pio_root_list')
> lib/logic_pio.c:41:3: error: field name not in record or union initializer
> .sec_min = PIO_SECT_MIN(PIO_CPU_MMIO),
> ^
> lib/logic_pio.c:41:3: note: (near initialization for 'logic_pio_root_list')
>>> lib/logic_pio.c:41:14: error: implicit declaration of function 'PIO_SECT_MIN' [-Werror=implicit-function-declaration]
> .sec_min = PIO_SECT_MIN(PIO_CPU_MMIO),
> ^~~~~~~~~~~~
> lib/logic_pio.c:42:3: error: field name not in record or union initializer
> .sec_max = PIO_SECT_MAX(PIO_INDIRECT - 1),
> ^
> lib/logic_pio.c:42:3: note: (near initialization for 'logic_pio_root_list')
>>> lib/logic_pio.c:42:14: error: implicit declaration of function 'PIO_SECT_MAX' [-Werror=implicit-function-declaration]
> .sec_max = PIO_SECT_MAX(PIO_INDIRECT - 1),
> ^~~~~~~~~~~~
> lib/logic_pio.c:46:3: error: array index in initializer not of integer type
> [PIO_INDIRECT] = {
> ^~~~~~~~~~~~
> lib/logic_pio.c:46:3: note: (near initialization for 'logic_pio_root_list')
> lib/logic_pio.c:47:3: error: field name not in record or union initializer
> .sec_head = LIST_HEAD_INIT(logic_pio_root_list[PIO_INDIRECT].sec_head),
> ^
> lib/logic_pio.c:47:3: note: (near initialization for 'logic_pio_root_list')
> lib/logic_pio.c:48:3: error: field name not in record or union initializer
> .sec_min = PIO_SECT_MIN(PIO_INDIRECT),
> ^
> lib/logic_pio.c:48:3: note: (near initialization for 'logic_pio_root_list')
> lib/logic_pio.c:49:3: error: field name not in record or union initializer
> .sec_max = PIO_SECT_MAX(PIO_INDIRECT),
> ^
> lib/logic_pio.c:49:3: note: (near initialization for 'logic_pio_root_list')
> In file included from include/linux/list.h:8:0,
> from include/linux/kobject.h:20,
> from include/linux/of.h:21,
> from lib/logic_pio.c:18:
> lib/logic_pio.c: In function 'logic_pio_find_range_byaddr':
>>> include/linux/rculist.h:351:49: error: dereferencing pointer to incomplete type 'struct logic_pio_hwaddr'
> for (pos = list_entry_rcu((head)->next, typeof(*pos), member); \
>
> include/linux/kernel.h:852:18: note: in definition of macro 'container_of'
> const typeof( ((type *)0)->member ) *__mptr = (ptr); \
> ^~~~
>>> include/linux/rculist.h:351:13: note: in expansion of macro 'list_entry_rcu'
> for (pos = list_entry_rcu((head)->next, typeof(*pos), member); \
> ^~~~~~~~~~~~~~
>>> lib/logic_pio.c:77:2: note: in expansion of macro 'list_for_each_entry_rcu'
> list_for_each_entry_rcu(range, &io_range_list, list) {
> ^~~~~~~~~~~~~~~~~~~~~~~
> include/linux/kernel.h:852:48: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types]
> const typeof( ((type *)0)->member ) *__mptr = (ptr); \
> ^
>>> include/linux/rculist.h:277:2: note: in expansion of macro 'container_of'
> container_of(lockless_dereference(ptr), type, member)
> ^~~~~~~~~~~~
>>> include/linux/rculist.h:351:13: note: in expansion of macro 'list_entry_rcu'
> for (pos = list_entry_rcu((head)->next, typeof(*pos), member); \
> ^~~~~~~~~~~~~~
>>> lib/logic_pio.c:77:2: note: in expansion of macro 'list_for_each_entry_rcu'
> list_for_each_entry_rcu(range, &io_range_list, list) {
> ^~~~~~~~~~~~~~~~~~~~~~~
>>> include/linux/kernel.h:852:48: warning: initialization makes pointer from integer without a cast [-Wint-conversion]
> const typeof( ((type *)0)->member ) *__mptr = (ptr); \
> ^
>>> include/linux/rculist.h:277:2: note: in expansion of macro 'container_of'
> container_of(lockless_dereference(ptr), type, member)
> ^~~~~~~~~~~~
> include/linux/rculist.h:353:9: note: in expansion of macro 'list_entry_rcu'
> pos = list_entry_rcu(pos->member.next, typeof(*pos), member))
> ^~~~~~~~~~~~~~
>>> lib/logic_pio.c:77:2: note: in expansion of macro 'list_for_each_entry_rcu'
> list_for_each_entry_rcu(range, &io_range_list, list) {
> ^~~~~~~~~~~~~~~~~~~~~~~
> lib/logic_pio.c: In function 'logic_pio_alloc_range':
>>> lib/logic_pio.c:109:19: error: dereferencing pointer to incomplete type 'struct logic_pio_root'
> idle_start = root->sec_min;
> ^~
> In file included from include/linux/list.h:8:0,
> from include/linux/kobject.h:20,
> from include/linux/of.h:21,
> from lib/logic_pio.c:18:
>>> include/linux/rculist.h:351:49: error: dereferencing pointer to incomplete type 'struct logic_pio_sect'
> for (pos = list_entry_rcu((head)->next, typeof(*pos), member); \
>
> include/linux/kernel.h:852:18: note: in definition of macro 'container_of'
> const typeof( ((type *)0)->member ) *__mptr = (ptr); \
> ^~~~
>>> include/linux/rculist.h:351:13: note: in expansion of macro 'list_entry_rcu'
> for (pos = list_entry_rcu((head)->next, typeof(*pos), member); \
> ^~~~~~~~~~~~~~
> lib/logic_pio.c:111:2: note: in expansion of macro 'list_for_each_entry_rcu'
> list_for_each_entry_rcu(entry, &root->sec_head, list) {
> ^~~~~~~~~~~~~~~~~~~~~~~
>>> include/linux/kernel.h:852:48: warning: initialization makes pointer from integer without a cast [-Wint-conversion]
> const typeof( ((type *)0)->member ) *__mptr = (ptr); \
> ^
>
> vim +/PIO_MAX_SECT +32 lib/logic_pio.c
>
> 12 * GNU General Public License for more details.
> 13 *
> 14 * You should have received a copy of the GNU General Public License
> 15 * along with this program. If not, see <http://www.gnu.org/licenses/>.
> 16 */
> 17
> > 18 #include <linux/of.h>
> 19 #include <linux/io.h>
> 20 #include <linux/mm.h>
> 21 #include <linux/rculist.h>
> 22 #include <linux/sizes.h>
> 23 #include <linux/slab.h>
> 24
> 25 /* The unique hardware address list. */
> 26 static LIST_HEAD(io_range_list);
> 27 static DEFINE_MUTEX(io_range_mutex);
> 28
> 29 /*
> 30 * These are the lists for PIO. The highest PIO_SECT_BITS of PIO is the index.
> 31 */
> > 32 static struct logic_pio_root logic_pio_root_list[PIO_MAX_SECT] = {
> 33 #ifdef CONFIG_INDIRECT_PIO
> 34 /*
> 35 * At this moment, assign all the other logic PIO space to MMIO.
> 36 * If more elements added, please adjust the ending index and .sec_max;
> 37 * Please keep MMIO element started from index ZERO.
> 38 */
> > 39 [PIO_CPU_MMIO ... PIO_INDIRECT - 1] = {
> > 40 .sec_head = LIST_HEAD_INIT(logic_pio_root_list[PIO_CPU_MMIO].sec_head),
> > 41 .sec_min = PIO_SECT_MIN(PIO_CPU_MMIO),
> > 42 .sec_max = PIO_SECT_MAX(PIO_INDIRECT - 1),
> 43 },
> 44
> 45 /* The last element */
> 46 [PIO_INDIRECT] = {
> 47 .sec_head = LIST_HEAD_INIT(logic_pio_root_list[PIO_INDIRECT].sec_head),
> 48 .sec_min = PIO_SECT_MIN(PIO_INDIRECT),
> 49 .sec_max = PIO_SECT_MAX(PIO_INDIRECT),
> 50 },
> 51 #else
> 52 [PIO_CPU_MMIO] = {
> 53 .sec_head = LIST_HEAD_INIT(logic_pio_root_list[PIO_CPU_MMIO].sec_head),
> 54 .sec_min = PIO_SECT_MIN(PIO_CPU_MMIO),
> 55 .sec_max = PIO_SECT_MAX(PIO_CPU_MMIO),
> 56 },
> 57
> 58 #endif
> 59 };
> 60
> 61 /*
> 62 * Search a io_range registered which match the fwnode and addr.
> 63 *
> 64 * @fwnode: the host fwnode which must be valid;
> 65 * @start: the start hardware address of this search;
> 66 * @end: the end hardware address of this search. can be equal to @start;
> 67 *
> 68 * return NULL when there is no matched node; IS_ERR() means ERROR;
> 69 * valid virtual address represent a matched node was found.
> 70 */
> 71 static struct logic_pio_hwaddr *
> 72 logic_pio_find_range_byaddr(struct fwnode_handle *fwnode,
> 73 resource_size_t start, resource_size_t end)
> 74 {
> 75 struct logic_pio_hwaddr *range;
> 76
> > 77 list_for_each_entry_rcu(range, &io_range_list, list) {
> 78 if (!range->pio_peer) {
> 79 pr_warn("Invalid cpu addr node(%pa) in list!\n",
> 80 &range->hw_start);
> 81 continue;
> 82 }
> 83 if (range->fwnode != fwnode)
> 84 continue;
> 85 /* without any overlap with current range */
> 86 if (start >= range->hw_start + range->size ||
> 87 end < range->hw_start)
> 88 continue;
> 89 /* overlap is not supported now. */
> 90 if (start < range->hw_start ||
> 91 end >= range->hw_start + range->size)
> 92 return ERR_PTR(-EBUSY);
> 93 /* had been registered. */
> 94 return range;
> 95 }
> 96
> 97 return NULL;
> 98 }
> 99
> 100
> 101 static int logic_pio_alloc_range(struct logic_pio_root *root,
> 102 resource_size_t size, unsigned long align,
> 103 struct list_head **prev, resource_size_t *pio_alloc)
> 104 {
> 105 struct logic_pio_sect *entry;
> 106 resource_size_t tmp_start;
> 107 resource_size_t idle_start, idle_end;
> 108
> > 109 idle_start = root->sec_min;
> 110 *prev = &root->sec_head;
> 111 list_for_each_entry_rcu(entry, &root->sec_head, list) {
> 112 if (!entry->hwpeer ||
> 113 idle_start > entry->io_start) {
> 114 WARN(1, "skip an invalid io range during traversal!\n");
> 115 goto nextentry;
> 116 }
> 117 /* set the end edge. */
> 118 if (idle_start == entry->io_start) {
> 119 struct logic_pio_sect *next;
> 120
> 121 idle_start = entry->io_start + entry->hwpeer->size;
> > 122 next = list_next_or_null_rcu(&root->sec_head,
> > 123 &entry->list, struct logic_pio_sect, list);
> 124 if (next) {
> 125 entry = next;
> 126 } else {
> 127 *prev = &entry->list;
> 128 break;
> 129 }
> 130 }
> 131 idle_end = entry->io_start - 1;
> 132
> 133 /* contiguous range... */
> 134 if (idle_start > idle_end)
> 135 goto nextentry;
> 136
> 137 tmp_start = idle_start;
> 138 idle_start = ALIGN(idle_start, align);
> 139 if (idle_start >= tmp_start &&
> 140 idle_start + size <= idle_end) {
> 141 *prev = &entry->list;
> 142 *pio_alloc = idle_start;
> 143 return 0;
> 144 }
> 145
> 146 nextentry:
> 147 idle_start = entry->io_start + entry->hwpeer->size;
> 148 *prev = &entry->list;
> 149 }
> 150 /* check the last free gap... */
> 151 idle_end = root->sec_max;
> 152
> 153 tmp_start = idle_start;
> 154 idle_start = ALIGN(idle_start, align);
> 155 if (idle_start >= tmp_start &&
> 156 idle_start + size <= idle_end) {
> 157 *pio_alloc = idle_start;
> 158 return 0;
> 159 }
> 160
> 161 return -EBUSY;
> 162 }
> 163
> 164 /*
> 165 * register a io range node in the io range list.
> 166 *
> 167 * @newrange: pointer to the io range to be registered.
> 168 *
> 169 * return 'newrange' when success, ERR_VALUE() is for failures.
> 170 * specially, return a valid pointer which is not equal to 'newrange' when
> 171 * the io range had been registered before.
> 172 */
> 173 struct logic_pio_hwaddr
> 174 *logic_pio_register_range(struct logic_pio_hwaddr *newrange,
> 175 unsigned long align)
> 176 {
> 177 struct logic_pio_hwaddr *range;
> 178 struct logic_pio_sect *newsect;
> 179 resource_size_t pio_alloc;
> 180 struct list_head *prev, *hwprev;
> 181 unsigned long sect_id;
> 182 int err;
> 183
> 184 if (!newrange || !newrange->fwnode || !newrange->size)
> 185 return ERR_PTR(-EINVAL);
> 186
> 187 sect_id = newrange->flags;
> 188 if (sect_id >= PIO_MAX_SECT)
> 189 return ERR_PTR(-EINVAL);
> 190
> 191 mutex_lock(&io_range_mutex);
> 192 range = logic_pio_find_range_byaddr(newrange->fwnode,
> 193 newrange->hw_start,
> 194 newrange->hw_start + newrange->size - 1);
> 195 if (range) {
> 196 if (!IS_ERR(range))
> 197 pr_info("the request IO range had been registered!\n");
> 198 else
> 199 pr_err("registering IO[%pa - sz%pa) got failed!\n",
> 200 &newrange->hw_start, &newrange->size);
> 201 mutex_unlock(&io_range_mutex);
> 202 return range;
> 203 }
> 204
> 205 err = logic_pio_alloc_range(&logic_pio_root_list[sect_id],
> 206 newrange->size, align, &prev, &pio_alloc);
> 207 if (err) {
> 208 pr_err("can't find free %pa logical IO range!\n",
> 209 &newrange->size);
> 210 goto exitproc;
> 211 }
> 212
> 213 if (prev == &logic_pio_root_list[sect_id].sec_head) {
> 214 hwprev = &io_range_list;
> 215 } else {
> > 216 newsect = to_pio_sect(prev);
> > 217 hwprev = &newsect->hwpeer->list;
> 218 }
> 219
> 220 newsect = kzalloc(sizeof(*newsect), GFP_KERNEL);
>
> ---
> 0-DAY kernel test infrastructure Open Source Technology Center
> https://lists.01.org/pipermail/kbuild-all Intel Corporation
>
^ permalink raw reply
* Re: [PATCH v4 8/8] ARM: sun8i: sina33: add highest OPP of CPUs
From: Maxime Ripard @ 2017-04-05 12:17 UTC (permalink / raw)
To: Quentin Schulz
Cc: dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
wens-jdAy2FN1RRM, lee.jones-QSEj5FYQhm4dnm+yROfE0A,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, jic23-DgEjT+Ai2ygdnm+yROfE0A,
knaack.h-Mmb7MZpHnFY, lars-Qo5EllUWu/uELgA04lAiVw,
pmeerw-jW+XmwGofnusTnJN9+BGXg,
thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
linux-input-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, icenowy-ymACFijhrKM
In-Reply-To: <20170405090634.4649-9-quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 631 bytes --]
On Wed, Apr 05, 2017 at 11:06:34AM +0200, Quentin Schulz wrote:
> The A33 supports 1.1GHz and 1.2GHz frequencies at 1.32V and the Sinlinx
> SinA33 has its cpu-supply property set in the cpu DT node.
>
> Therefore, CPUfreq knows how to handle the regulator in charge of the
> CPU and can adjust its voltage to match the OPP.
>
> Add these two CPU frequencies to the CPU OPP table of the Sinlinx
> SinA33.
>
> Signed-off-by: Quentin Schulz <quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply
* Re: [PATCH v4 7/8] ARM: sun8i: a33: Add devfreq-based GPU cooling
From: Maxime Ripard @ 2017-04-05 12:16 UTC (permalink / raw)
To: Quentin Schulz
Cc: dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
wens-jdAy2FN1RRM, lee.jones-QSEj5FYQhm4dnm+yROfE0A,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, jic23-DgEjT+Ai2ygdnm+yROfE0A,
knaack.h-Mmb7MZpHnFY, lars-Qo5EllUWu/uELgA04lAiVw,
pmeerw-jW+XmwGofnusTnJN9+BGXg,
thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
linux-input-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, icenowy-ymACFijhrKM
In-Reply-To: <20170405090634.4649-8-quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 535 bytes --]
On Wed, Apr 05, 2017 at 11:06:33AM +0200, Quentin Schulz wrote:
> From: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
>
> This adds GPU thermal throttling for the Allwinner A33.
>
> Signed-off-by: Maxime Ripard <maxime.ripard-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> Signed-off-by: Quentin Schulz <quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
Applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply
* Re: [PATCH v2 1/3] clk: vc5: Add structure to describe particular chip features
From: Geert Uytterhoeven @ 2017-04-05 12:15 UTC (permalink / raw)
To: Alexey Firago
Cc: Michael Turquette, Stephen Boyd, Rob Herring, Marek Vasut,
linux-clk, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
In-Reply-To: <1491392819-698-2-git-send-email-alexey_firago-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
Hi Alexey,
On Wed, Apr 5, 2017 at 1:46 PM, Alexey Firago <alexey_firago-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org> wrote:
> Introduce vc5_chip_info structure to describe features of a particular
> VC5 chip (id, number of FODs, number of outputs, flags).
> For now flags are only used to indicate if chip has internal XTAL.
> vc5_chip_info is set on probe from the matched of_device_id->data.
>
> Also add defines to specify maximum number of FODs and clock outputs
> supported by the driver.
>
> With these changes it should be easier to extend driver to support
> more VC5 models.
>
> Signed-off-by: Alexey Firago <alexey_firago-nmGgyN9QBj3QT0dZR+AlfA@public.gmane.org>
Thanks for your patch!
Reviewed-by: Geert Uytterhoeven <geert+renesas-gXvu3+zWzMSzQB+pC5nmwQ@public.gmane.org>
> --- a/drivers/clk/clk-versaclock5.c
> +++ b/drivers/clk/clk-versaclock5.c
> @@ -113,12 +113,30 @@
> #define VC5_MUX_IN_XIN BIT(0)
> #define VC5_MUX_IN_CLKIN BIT(1)
>
> +/* Maximum number of clk_out supported by this driver */
> +#define VC5_MAX_CLK_OUT_NUM 3
> +
> +/* Maximum number of FODs supported by this driver */
> +#define VC5_MAX_FOD_NUM 2
> +
> +/* flags to describe chip features */
> +/* chip has built-in oscilator */
> +#define VC5_HAS_INTERNAL_XTAL BIT(0)
VC5_HAS_INTERNAL_OSC?
> +
> /* Supported IDT VC5 models. */
> enum vc5_model {
> IDT_VC5_5P49V5923,
> IDT_VC5_5P49V5933,
> };
>
> +/* Structure to describe features of a particular VC5 model */
> +struct vc5_chip_info {
> + const enum vc5_model model;
> + const int clk_fod_cnt;
> + const int clk_out_cnt;
const unsigned int (both)
> + u32 flags;
> +};
> +
> struct vc5_driver_data;
>
> struct vc5_hw_data {
> @@ -132,15 +150,15 @@ struct vc5_hw_data {
> struct vc5_driver_data {
> struct i2c_client *client;
> struct regmap *regmap;
> - enum vc5_model model;
> + struct vc5_chip_info *chip_info;
const struct vc5_chip_info *chip_info;
> @@ -591,7 +609,7 @@ static int vc5_probe(struct i2c_client *client,
> struct vc5_driver_data *vc5;
> struct clk_init_data init;
> const char *parent_names[2];
> - unsigned int n, idx;
> + unsigned int n, idx = 0;
> int ret;
>
> vc5 = devm_kzalloc(&client->dev, sizeof(*vc5), GFP_KERNEL);
> @@ -600,7 +618,12 @@ static int vc5_probe(struct i2c_client *client,
>
> i2c_set_clientdata(client, vc5);
> vc5->client = client;
> - vc5->model = (enum vc5_model)of_id->data;
> +
> + vc5->chip_info = (struct vc5_chip_info *)of_id->data;
I think the cast is no longer needed when chip_info becomes const.
BTW, of_id is not really needed if you write it like:
vc5->chip_info = of_device_get_match_data(&client->dev);
> + if (!vc5->chip_info) {
This can't really happen, can it?
> + dev_err(&client->dev, "No device match found\n");
> + return -ENODEV;
> + }
>
> vc5->pin_xin = devm_clk_get(&client->dev, "xin");
> if (PTR_ERR(vc5->pin_xin) == -EPROBE_DEFER)
> @@ -622,8 +645,8 @@ static int vc5_probe(struct i2c_client *client,
> if (!IS_ERR(vc5->pin_xin)) {
> vc5->clk_mux_ins |= VC5_MUX_IN_XIN;
> parent_names[init.num_parents++] = __clk_get_name(vc5->pin_xin);
> - } else if (vc5->model == IDT_VC5_5P49V5933) {
> - /* IDT VC5 5P49V5933 has built-in oscilator. */
> + } else if (vc5->chip_info->flags & VC5_HAS_INTERNAL_XTAL) {
> + /* chip has built-in oscilator. */
The comment is no longer needed when the bit is named VC5_HAS_INTERNAL_OSC :-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [PATCH v4 6/8] ARM: sun8i: a33: add CPU thermal throttling
From: Maxime Ripard @ 2017-04-05 12:13 UTC (permalink / raw)
To: Quentin Schulz
Cc: dmitry.torokhov-Re5JQEeQqe8AvxtiuMwx3w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
wens-jdAy2FN1RRM, lee.jones-QSEj5FYQhm4dnm+yROfE0A,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, jic23-DgEjT+Ai2ygdnm+yROfE0A,
knaack.h-Mmb7MZpHnFY, lars-Qo5EllUWu/uELgA04lAiVw,
pmeerw-jW+XmwGofnusTnJN9+BGXg,
thomas.petazzoni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8,
linux-input-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-iio-u79uwXL29TY76Z2rM5mHXA,
linux-sunxi-/JYPxA39Uh5TLH3MbocFFw, icenowy-ymACFijhrKM
In-Reply-To: <20170405090634.4649-7-quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
[-- Attachment #1: Type: text/plain, Size: 2445 bytes --]
On Wed, Apr 05, 2017 at 11:06:32AM +0200, Quentin Schulz wrote:
> This adds CPU thermal throttling for the Allwinner A33. It uses the
> thermal sensor present in the SoC's GPADC.
>
> Signed-off-by: Quentin Schulz <quentin.schulz-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> ---
>
> v3:
> - switched to new phandle because of modified DT node name for the GPADC
> (named THS),
> - got rid of cooling-min-level and cooling-max-level as it's not used in any
> code in the kernel,
>
> v2:
> - updated cooling-max-level to reflect newly added OPPs,
>
> arch/arm/boot/dts/sun8i-a33.dtsi | 45 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
> index 9734e63..b88c107 100644
> --- a/arch/arm/boot/dts/sun8i-a33.dtsi
> +++ b/arch/arm/boot/dts/sun8i-a33.dtsi
> @@ -43,6 +43,7 @@
> */
>
> #include "sun8i-a23-a33.dtsi"
> +#include <dt-bindings/thermal/thermal.h>
>
> / {
> cpu0_opp_table: opp_table0 {
> @@ -127,6 +128,7 @@
> clocks = <&ccu CLK_CPUX>;
> clock-names = "cpu";
> operating-points-v2 = <&cpu0_opp_table>;
> + #cooling-cells = <2>;
> };
>
> cpu@1 {
> @@ -170,6 +172,49 @@
> };
> };
>
> + thermal-zones {
> + cpu_thermal {
> + /* milliseconds */
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> + thermal-sensors = <&ths>;
> +
> + cooling-maps {
> + map0 {
> + trip = <&cpu_alert0>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + map1 {
> + trip = <&cpu_alert1>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> +
> + trips {
> + cpu_alert0: cpu_alert0 {
> + /* milliCelsius */
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + cpu_alert1: cpu_alert1 {
> + /* milliCelsius */
> + temperature = <90000>;
> + hysteresis = <2000>;
> + type = "hot";
> + };
> +
> + cpu_crit: cpu_crit {
> + /* milliCelsius */
> + temperature = <110000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +
This wasn't sorted properly (thermal is not between mali- and memory
in the alphabetical order). Fixed and applied, thanks!
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox