* [PATCH] xtensa: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:54 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, Chris Zankel, Max Filippov,
devicetree, linux-xtensa, linux-kernel
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/xtensa/boot/dts/csp.dts | 2 +-
arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi | 10 +++++-----
arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi | 10 +++++-----
arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi | 6 +++---
arch/xtensa/boot/dts/xtfpga.dtsi | 10 +++++-----
5 files changed, 19 insertions(+), 19 deletions(-)
diff --git a/arch/xtensa/boot/dts/csp.dts b/arch/xtensa/boot/dts/csp.dts
index 885495460f7e..96c9bca1d737 100644
--- a/arch/xtensa/boot/dts/csp.dts
+++ b/arch/xtensa/boot/dts/csp.dts
@@ -44,7 +44,7 @@
compatible = "simple-bus";
ranges = <0x00000000 0xf0000000 0x10000000>;
- uart0: serial@0d000000 {
+ uart0: serial@d000000 {
compatible = "xlnx,xuartps", "cdns,uart-r1p8";
clocks = <&osc>, <&osc>;
clock-names = "uart_clk", "pclk";
diff --git a/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi b/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi
index 9bf8bad1dd18..7b0cd356e0db 100644
--- a/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi
+++ b/arch/xtensa/boot/dts/xtfpga-flash-128m.dtsi
@@ -1,26 +1,26 @@
// SPDX-License-Identifier: GPL-2.0
/ {
soc {
- flash: flash@00000000 {
+ flash: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x00000000 0x08000000>;
bank-width = <2>;
device-width = <2>;
- partition@0x0 {
+ partition@0 {
label = "data";
reg = <0x00000000 0x06000000>;
};
- partition@0x6000000 {
+ partition@6000000 {
label = "boot loader area";
reg = <0x06000000 0x00800000>;
};
- partition@0x6800000 {
+ partition@6800000 {
label = "kernel image";
reg = <0x06800000 0x017e0000>;
};
- partition@0x7fe0000 {
+ partition@7fe0000 {
label = "boot environment";
reg = <0x07fe0000 0x00020000>;
};
diff --git a/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi b/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi
index 40c2f81f7cb6..c5e56cf0f8df 100644
--- a/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi
+++ b/arch/xtensa/boot/dts/xtfpga-flash-16m.dtsi
@@ -1,26 +1,26 @@
// SPDX-License-Identifier: GPL-2.0
/ {
soc {
- flash: flash@08000000 {
+ flash: flash@8000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x08000000 0x01000000>;
bank-width = <2>;
device-width = <2>;
- partition@0x0 {
+ partition@0 {
label = "boot loader area";
reg = <0x00000000 0x00400000>;
};
- partition@0x400000 {
+ partition@400000 {
label = "kernel image";
reg = <0x00400000 0x00600000>;
};
- partition@0xa00000 {
+ partition@a00000 {
label = "data";
reg = <0x00a00000 0x005e0000>;
};
- partition@0xfe0000 {
+ partition@fe0000 {
label = "boot environment";
reg = <0x00fe0000 0x00020000>;
};
diff --git a/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi b/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi
index fb8d3a9f33c2..ad0d2ec45447 100644
--- a/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi
+++ b/arch/xtensa/boot/dts/xtfpga-flash-4m.dtsi
@@ -1,18 +1,18 @@
// SPDX-License-Identifier: GPL-2.0
/ {
soc {
- flash: flash@08000000 {
+ flash: flash@8000000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "cfi-flash";
reg = <0x08000000 0x00400000>;
bank-width = <2>;
device-width = <2>;
- partition@0x0 {
+ partition@0 {
label = "boot loader area";
reg = <0x00000000 0x003f0000>;
};
- partition@0x3f0000 {
+ partition@3f0000 {
label = "boot environment";
reg = <0x003f0000 0x00010000>;
};
diff --git a/arch/xtensa/boot/dts/xtfpga.dtsi b/arch/xtensa/boot/dts/xtfpga.dtsi
index 1090528825ec..5ede496ed9be 100644
--- a/arch/xtensa/boot/dts/xtfpga.dtsi
+++ b/arch/xtensa/boot/dts/xtfpga.dtsi
@@ -54,7 +54,7 @@
reg = <0x0d020004 0x4>;
};
- serial0: serial@0d050020 {
+ serial0: serial@d050020 {
device_type = "serial";
compatible = "ns16550a";
no-loopback-test;
@@ -66,7 +66,7 @@
clocks = <&osc>;
};
- enet0: ethoc@0d030000 {
+ enet0: ethoc@d030000 {
compatible = "opencores,ethoc";
reg = <0x0d030000 0x4000 0x0d800000 0x4000>;
native-endian;
@@ -75,7 +75,7 @@
clocks = <&osc>;
};
- i2s0: xtfpga-i2s@0d080000 {
+ i2s0: xtfpga-i2s@d080000 {
#sound-dai-cells = <0>;
compatible = "cdns,xtfpga-i2s";
reg = <0x0d080000 0x40>;
@@ -83,7 +83,7 @@
clocks = <&cdce706 4>;
};
- i2c0: i2c-master@0d090000 {
+ i2c0: i2c-master@d090000 {
compatible = "opencores,i2c-ocores";
#address-cells = <1>;
#size-cells = <0>;
@@ -103,7 +103,7 @@
};
};
- spi0: spi-master@0d0a0000 {
+ spi0: spi-master@d0a0000 {
compatible = "cdns,xtfpga-spi";
#address-cells = <1>;
#size-cells = <0>;
--
2.11.0
^ permalink raw reply related
* [PATCH] powerpc: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:54 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, Benjamin Herrenschmidt,
Paul Mackerras, Michael Ellerman, Andrew Morton, Masahiro Yamada,
devicetree, linuxppc-dev, linux-kernel
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/powerpc/boot/dts/a3m071.dts | 10 +++++-----
arch/powerpc/boot/dts/akebono.dts | 4 ++--
arch/powerpc/boot/dts/c2k.dts | 6 +++---
arch/powerpc/boot/dts/currituck.dts | 2 +-
arch/powerpc/boot/dts/fsl/mpc8568mds.dts | 12 +++++------
arch/powerpc/boot/dts/fsl/mpc8569mds.dts | 20 +++++++++----------
arch/powerpc/boot/dts/fsl/p1021mds.dts | 6 +++---
arch/powerpc/boot/dts/fsl/p1025rdb.dtsi | 8 ++++----
arch/powerpc/boot/dts/fsl/p1025rdb_32b.dts | 2 +-
arch/powerpc/boot/dts/fsl/p1025twr.dtsi | 8 ++++----
arch/powerpc/boot/dts/fsl/t1040rdb.dts | 2 +-
arch/powerpc/boot/dts/fsl/t1042d4rdb.dts | 10 +++++-----
arch/powerpc/boot/dts/fsl/t1042rdb.dts | 2 +-
arch/powerpc/boot/dts/fsl/t104xrdb.dtsi | 6 +++---
arch/powerpc/boot/dts/fsp2.dts | 6 +++---
arch/powerpc/boot/dts/gamecube.dts | 14 ++++++-------
arch/powerpc/boot/dts/haleakala.dts | 2 +-
arch/powerpc/boot/dts/kilauea.dts | 4 ++--
arch/powerpc/boot/dts/kmeter1.dts | 10 +++++-----
arch/powerpc/boot/dts/makalu.dts | 4 ++--
arch/powerpc/boot/dts/mpc832x_mds.dts | 10 +++++-----
arch/powerpc/boot/dts/mpc832x_rdb.dts | 8 ++++----
arch/powerpc/boot/dts/mpc836x_mds.dts | 8 ++++----
arch/powerpc/boot/dts/sbc8548-altflash.dts | 8 ++++----
arch/powerpc/boot/dts/sbc8548.dts | 8 ++++----
arch/powerpc/boot/dts/wii.dts | 32 +++++++++++++++---------------
26 files changed, 106 insertions(+), 106 deletions(-)
diff --git a/arch/powerpc/boot/dts/a3m071.dts b/arch/powerpc/boot/dts/a3m071.dts
index bf81b8f9704c..187ce458d03a 100644
--- a/arch/powerpc/boot/dts/a3m071.dts
+++ b/arch/powerpc/boot/dts/a3m071.dts
@@ -105,24 +105,24 @@
reg = <0 0x0 0x02000000>;
compatible = "cfi-flash";
bank-width = <2>;
- partition@0x0 {
+ partition@0 {
label = "u-boot";
reg = <0x00000000 0x00040000>;
read-only;
};
- partition@0x00040000 {
+ partition@40000 {
label = "env";
reg = <0x00040000 0x00020000>;
};
- partition@0x00060000 {
+ partition@60000 {
label = "dtb";
reg = <0x00060000 0x00020000>;
};
- partition@0x00080000 {
+ partition@80000 {
label = "kernel";
reg = <0x00080000 0x00500000>;
};
- partition@0x00580000 {
+ partition@580000 {
label = "root";
reg = <0x00580000 0x00A80000>;
};
diff --git a/arch/powerpc/boot/dts/akebono.dts b/arch/powerpc/boot/dts/akebono.dts
index e61d5dc598c1..746779202a12 100644
--- a/arch/powerpc/boot/dts/akebono.dts
+++ b/arch/powerpc/boot/dts/akebono.dts
@@ -216,7 +216,7 @@
interrupts = <39 2>;
};
- IIC0: i2c@00000000 {
+ IIC0: i2c@0 {
compatible = "ibm,iic-476gtr", "ibm,iic";
reg = <0x0 0x00000020>;
interrupt-parent = <&MPIC>;
@@ -229,7 +229,7 @@
};
};
- IIC1: i2c@00000100 {
+ IIC1: i2c@100 {
compatible = "ibm,iic-476gtr", "ibm,iic";
reg = <0x100 0x00000020>;
interrupt-parent = <&MPIC>;
diff --git a/arch/powerpc/boot/dts/c2k.dts b/arch/powerpc/boot/dts/c2k.dts
index 1e32903cb0a8..27f169e3ade9 100644
--- a/arch/powerpc/boot/dts/c2k.dts
+++ b/arch/powerpc/boot/dts/c2k.dts
@@ -276,14 +276,14 @@
>;
};
- cpu-error@0070 {
+ cpu-error@70 {
compatible = "marvell,mv64360-cpu-error";
reg = <0x0070 0x10 0x0128 0x28>;
interrupts = <3>;
interrupt-parent = <&PIC>;
};
- sram-ctrl@0380 {
+ sram-ctrl@380 {
compatible = "marvell,mv64360-sram-ctrl";
reg = <0x0380 0x80>;
interrupts = <13>;
@@ -311,7 +311,7 @@
interrupt-parent = <&PIC>;
};
/* Devices attached to the device controller */
- devicebus@045c {
+ devicebus@45c {
#address-cells = <2>;
#size-cells = <1>;
compatible = "marvell,mv64306-devctrl";
diff --git a/arch/powerpc/boot/dts/currituck.dts b/arch/powerpc/boot/dts/currituck.dts
index 4191e1850ea1..f2ad5815f08d 100644
--- a/arch/powerpc/boot/dts/currituck.dts
+++ b/arch/powerpc/boot/dts/currituck.dts
@@ -108,7 +108,7 @@
reg = <0x50000000 0x4>;
};
- IIC0: i2c@00000000 {
+ IIC0: i2c@0 {
compatible = "ibm,iic-currituck", "ibm,iic";
reg = <0x0 0x00000014>;
interrupt-parent = <&MPIC>;
diff --git a/arch/powerpc/boot/dts/fsl/mpc8568mds.dts b/arch/powerpc/boot/dts/fsl/mpc8568mds.dts
index 01706a339603..bc3e8039bdc7 100644
--- a/arch/powerpc/boot/dts/fsl/mpc8568mds.dts
+++ b/arch/powerpc/boot/dts/fsl/mpc8568mds.dts
@@ -126,7 +126,7 @@
par_io@e0100 {
num-ports = <7>;
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x4 0xa 0x1 0x0 0x2 0x0 /* TxD0 */
@@ -154,7 +154,7 @@
0x1 0x1f 0x2 0x0 0x3 0x0>; /* GTX125 */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x5 0xa 0x1 0x0 0x2 0x0 /* TxD0 */
@@ -228,22 +228,22 @@
/* These are the same PHYs as on
* gianfar's MDIO bus */
- qe_phy0: ethernet-phy@07 {
+ qe_phy0: ethernet-phy@7 {
interrupt-parent = <&mpic>;
interrupts = <1 1 0 0>;
reg = <0x7>;
};
- qe_phy1: ethernet-phy@01 {
+ qe_phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1 0 0>;
reg = <0x1>;
};
- qe_phy2: ethernet-phy@02 {
+ qe_phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <1 1 0 0>;
reg = <0x2>;
};
- qe_phy3: ethernet-phy@03 {
+ qe_phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <2 1 0 0>;
reg = <0x3>;
diff --git a/arch/powerpc/boot/dts/fsl/mpc8569mds.dts b/arch/powerpc/boot/dts/fsl/mpc8569mds.dts
index 76b2bd6f7742..d8367ceddea6 100644
--- a/arch/powerpc/boot/dts/fsl/mpc8569mds.dts
+++ b/arch/powerpc/boot/dts/fsl/mpc8569mds.dts
@@ -141,7 +141,7 @@
gpio-controller;
};
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -161,7 +161,7 @@
0x2 0x14 0x1 0x0 0x2 0x0>; /* ENET1_GTXCLK */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -181,7 +181,7 @@
0x2 0x2 0x1 0x0 0x2 0x0>; /* ENET2_GTXCLK */
};
- pio3: ucc_pin@03 {
+ pio3: ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -201,7 +201,7 @@
0x2 0x19 0x1 0x0 0x2 0x0>; /* ENET3_GTXCLK */
};
- pio4: ucc_pin@04 {
+ pio4: ucc_pin@4 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x2 0x1f 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -272,30 +272,30 @@
reg = <0x2120 0x18>;
compatible = "fsl,ucc-mdio";
- qe_phy0: ethernet-phy@07 {
+ qe_phy0: ethernet-phy@7 {
interrupt-parent = <&mpic>;
interrupts = <1 1 0 0>;
reg = <0x7>;
};
- qe_phy1: ethernet-phy@01 {
+ qe_phy1: ethernet-phy@1 {
interrupt-parent = <&mpic>;
interrupts = <2 1 0 0>;
reg = <0x1>;
};
- qe_phy2: ethernet-phy@02 {
+ qe_phy2: ethernet-phy@2 {
interrupt-parent = <&mpic>;
interrupts = <3 1 0 0>;
reg = <0x2>;
};
- qe_phy3: ethernet-phy@03 {
+ qe_phy3: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <4 1 0 0>;
reg = <0x3>;
};
- qe_phy5: ethernet-phy@04 {
+ qe_phy5: ethernet-phy@4 {
reg = <0x04>;
};
- qe_phy7: ethernet-phy@06 {
+ qe_phy7: ethernet-phy@6 {
reg = <0x6>;
};
tbi1: tbi-phy@11 {
diff --git a/arch/powerpc/boot/dts/fsl/p1021mds.dts b/arch/powerpc/boot/dts/fsl/p1021mds.dts
index 291454c75dda..1047802f4d2a 100644
--- a/arch/powerpc/boot/dts/fsl/p1021mds.dts
+++ b/arch/powerpc/boot/dts/fsl/p1021mds.dts
@@ -202,7 +202,7 @@
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -225,7 +225,7 @@
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -296,7 +296,7 @@
interrupts = <4 1 0 0>;
reg = <0x0>;
};
- qe_phy1: ethernet-phy@03 {
+ qe_phy1: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <5 1 0 0>;
reg = <0x3>;
diff --git a/arch/powerpc/boot/dts/fsl/p1025rdb.dtsi b/arch/powerpc/boot/dts/fsl/p1025rdb.dtsi
index d44bb12debb0..0a5434a631c3 100644
--- a/arch/powerpc/boot/dts/fsl/p1025rdb.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p1025rdb.dtsi
@@ -245,7 +245,7 @@
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -268,7 +268,7 @@
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -283,7 +283,7 @@
0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
};
- pio3: ucc_pin@03 {
+ pio3: ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
@@ -293,7 +293,7 @@
0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
};
- pio4: ucc_pin@04 {
+ pio4: ucc_pin@4 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
diff --git a/arch/powerpc/boot/dts/fsl/p1025rdb_32b.dts b/arch/powerpc/boot/dts/fsl/p1025rdb_32b.dts
index b15acbaea34b..ea33b57f8774 100644
--- a/arch/powerpc/boot/dts/fsl/p1025rdb_32b.dts
+++ b/arch/powerpc/boot/dts/fsl/p1025rdb_32b.dts
@@ -106,7 +106,7 @@
interrupts = <4 1 0 0>;
reg = <0x6>;
};
- qe_phy1: ethernet-phy@03 {
+ qe_phy1: ethernet-phy@3 {
interrupt-parent = <&mpic>;
interrupts = <5 1 0 0>;
reg = <0x3>;
diff --git a/arch/powerpc/boot/dts/fsl/p1025twr.dtsi b/arch/powerpc/boot/dts/fsl/p1025twr.dtsi
index 08816fb474f5..ab75b8f29ae2 100644
--- a/arch/powerpc/boot/dts/fsl/p1025twr.dtsi
+++ b/arch/powerpc/boot/dts/fsl/p1025twr.dtsi
@@ -172,7 +172,7 @@
ranges = <0x0 0xe0100 0x60>;
device_type = "par_io";
num-ports = <3>;
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -195,7 +195,7 @@
0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */
@@ -210,7 +210,7 @@
0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */
};
- pio3: ucc_pin@03 {
+ pio3: ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x0 0x16 0x2 0x0 0x2 0x0 /* SER7_CD_B*/
@@ -220,7 +220,7 @@
0x0 0x15 0x1 0x0 0x2 0x0>; /* SER7_TXD0*/
};
- pio4: ucc_pin@04 {
+ pio4: ucc_pin@4 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0x1 0x0 0x2 0x0 0x2 0x0 /* SER3_CD_B*/
diff --git a/arch/powerpc/boot/dts/fsl/t1040rdb.dts b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
index 621f2c6ee6ad..65ff34c49025 100644
--- a/arch/powerpc/boot/dts/fsl/t1040rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1040rdb.dts
@@ -61,7 +61,7 @@
};
mdio@fc000 {
- phy_sgmii_2: ethernet-phy@03 {
+ phy_sgmii_2: ethernet-phy@3 {
reg = <0x03>;
};
};
diff --git a/arch/powerpc/boot/dts/fsl/t1042d4rdb.dts b/arch/powerpc/boot/dts/fsl/t1042d4rdb.dts
index fcd2aeb5b8ac..4fa15f48a4c3 100644
--- a/arch/powerpc/boot/dts/fsl/t1042d4rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1042d4rdb.dts
@@ -77,23 +77,23 @@
};
mdio0: mdio@fc000 {
- phy_sgmii_0: ethernet-phy@02 {
+ phy_sgmii_0: ethernet-phy@2 {
reg = <0x02>;
};
- phy_sgmii_1: ethernet-phy@03 {
+ phy_sgmii_1: ethernet-phy@3 {
reg = <0x03>;
};
- phy_sgmii_2: ethernet-phy@01 {
+ phy_sgmii_2: ethernet-phy@1 {
reg = <0x01>;
};
- phy_rgmii_0: ethernet-phy@04 {
+ phy_rgmii_0: ethernet-phy@4 {
reg = <0x04>;
};
- phy_rgmii_1: ethernet-phy@05 {
+ phy_rgmii_1: ethernet-phy@5 {
reg = <0x05>;
};
};
diff --git a/arch/powerpc/boot/dts/fsl/t1042rdb.dts b/arch/powerpc/boot/dts/fsl/t1042rdb.dts
index 2c138627b1b4..3ebb712224cb 100644
--- a/arch/powerpc/boot/dts/fsl/t1042rdb.dts
+++ b/arch/powerpc/boot/dts/fsl/t1042rdb.dts
@@ -59,7 +59,7 @@
};
mdio@fc000 {
- phy_sgmii_2: ethernet-phy@03 {
+ phy_sgmii_2: ethernet-phy@3 {
reg = <0x03>;
};
};
diff --git a/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi b/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi
index 5fdddbd2a62b..099a598c74c0 100644
--- a/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi
+++ b/arch/powerpc/boot/dts/fsl/t104xrdb.dtsi
@@ -148,15 +148,15 @@
};
mdio0: mdio@fc000 {
- phy_sgmii_2: ethernet-phy@03 {
+ phy_sgmii_2: ethernet-phy@3 {
reg = <0x03>;
};
- phy_rgmii_0: ethernet-phy@01 {
+ phy_rgmii_0: ethernet-phy@1 {
reg = <0x01>;
};
- phy_rgmii_1: ethernet-phy@02 {
+ phy_rgmii_1: ethernet-phy@2 {
reg = <0x02>;
};
};
diff --git a/arch/powerpc/boot/dts/fsp2.dts b/arch/powerpc/boot/dts/fsp2.dts
index f10a64aeb83b..6560283c5aec 100644
--- a/arch/powerpc/boot/dts/fsp2.dts
+++ b/arch/powerpc/boot/dts/fsp2.dts
@@ -583,21 +583,21 @@
};
};
- OHCI1: ohci@02040000 {
+ OHCI1: ohci@2040000 {
compatible = "ohci-le";
reg = <0x02040000 0xa0>;
interrupt-parent = <&UIC1_3>;
interrupts = <28 0x8 29 0x8>;
};
- OHCI2: ohci@02080000 {
+ OHCI2: ohci@2080000 {
compatible = "ohci-le";
reg = <0x02080000 0xa0>;
interrupt-parent = <&UIC1_3>;
interrupts = <30 0x8 31 0x8>;
};
- EHCI: ehci@02000000 {
+ EHCI: ehci@2000000 {
compatible = "usb-ehci";
reg = <0x02000000 0xa4>;
interrupt-parent = <&UIC1_3>;
diff --git a/arch/powerpc/boot/dts/gamecube.dts b/arch/powerpc/boot/dts/gamecube.dts
index ef3be0e58b02..58d06c9ee08b 100644
--- a/arch/powerpc/boot/dts/gamecube.dts
+++ b/arch/powerpc/boot/dts/gamecube.dts
@@ -54,13 +54,13 @@
ranges = <0x0c000000 0x0c000000 0x00010000>;
interrupt-parent = <&PIC>;
- video@0c002000 {
+ video@c002000 {
compatible = "nintendo,flipper-vi";
reg = <0x0c002000 0x100>;
interrupts = <8>;
};
- processor-interface@0c003000 {
+ processor-interface@c003000 {
compatible = "nintendo,flipper-pi";
reg = <0x0c003000 0x100>;
@@ -71,7 +71,7 @@
};
};
- dsp@0c005000 {
+ dsp@c005000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "nintendo,flipper-dsp";
@@ -84,26 +84,26 @@
};
};
- disk@0c006000 {
+ disk@c006000 {
compatible = "nintendo,flipper-di";
reg = <0x0c006000 0x40>;
interrupts = <2>;
};
- audio@0c006c00 {
+ audio@c006c00 {
compatible = "nintendo,flipper-ai";
reg = <0x0c006c00 0x20>;
interrupts = <6>;
};
- gamepad-controller@0c006400 {
+ gamepad-controller@c006400 {
compatible = "nintendo,flipper-si";
reg = <0x0c006400 0x100>;
interrupts = <3>;
};
/* External Interface bus */
- exi@0c006800 {
+ exi@c006800 {
compatible = "nintendo,flipper-exi";
reg = <0x0c006800 0x40>;
virtual-reg = <0x0c006800>;
diff --git a/arch/powerpc/boot/dts/haleakala.dts b/arch/powerpc/boot/dts/haleakala.dts
index 2b256694eca6..cb16dad43c92 100644
--- a/arch/powerpc/boot/dts/haleakala.dts
+++ b/arch/powerpc/boot/dts/haleakala.dts
@@ -237,7 +237,7 @@
};
};
- PCIE0: pciex@0a0000000 {
+ PCIE0: pciex@a0000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
diff --git a/arch/powerpc/boot/dts/kilauea.dts b/arch/powerpc/boot/dts/kilauea.dts
index 5ba7f01e2a29..2a3413221cc1 100644
--- a/arch/powerpc/boot/dts/kilauea.dts
+++ b/arch/powerpc/boot/dts/kilauea.dts
@@ -322,7 +322,7 @@
};
};
- PCIE0: pciex@0a0000000 {
+ PCIE0: pciex@a0000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -363,7 +363,7 @@
0x0 0x0 0x0 0x4 &UIC2 0x3 0x4 /* swizzled int D */>;
};
- PCIE1: pciex@0c0000000 {
+ PCIE1: pciex@c0000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
diff --git a/arch/powerpc/boot/dts/kmeter1.dts b/arch/powerpc/boot/dts/kmeter1.dts
index 983aee185793..9fa33d9ba966 100644
--- a/arch/powerpc/boot/dts/kmeter1.dts
+++ b/arch/powerpc/boot/dts/kmeter1.dts
@@ -434,27 +434,27 @@
compatible = "fsl,ucc-mdio";
/* Piggy2 (UCC4, MDIO 0x00, RMII) */
- phy_piggy2: ethernet-phy@00 {
+ phy_piggy2: ethernet-phy@0 {
reg = <0x0>;
};
/* Eth-1 (UCC5, MDIO 0x08, RMII) */
- phy_eth1: ethernet-phy@08 {
+ phy_eth1: ethernet-phy@8 {
reg = <0x08>;
};
/* Eth-2 (UCC6, MDIO 0x09, RMII) */
- phy_eth2: ethernet-phy@09 {
+ phy_eth2: ethernet-phy@9 {
reg = <0x09>;
};
/* Eth-3 (UCC7, MDIO 0x0a, RMII) */
- phy_eth3: ethernet-phy@0a {
+ phy_eth3: ethernet-phy@a {
reg = <0x0a>;
};
/* Eth-4 (UCC8, MDIO 0x0b, RMII) */
- phy_eth4: ethernet-phy@0b {
+ phy_eth4: ethernet-phy@b {
reg = <0x0b>;
};
diff --git a/arch/powerpc/boot/dts/makalu.dts b/arch/powerpc/boot/dts/makalu.dts
index 63d48b632c84..bf8fe1629392 100644
--- a/arch/powerpc/boot/dts/makalu.dts
+++ b/arch/powerpc/boot/dts/makalu.dts
@@ -268,7 +268,7 @@
};
};
- PCIE0: pciex@0a0000000 {
+ PCIE0: pciex@a0000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
@@ -309,7 +309,7 @@
0x0 0x0 0x0 0x4 &UIC2 0x3 0x4 /* swizzled int D */>;
};
- PCIE1: pciex@0c0000000 {
+ PCIE1: pciex@c0000000 {
device_type = "pci";
#interrupt-cells = <1>;
#size-cells = <2>;
diff --git a/arch/powerpc/boot/dts/mpc832x_mds.dts b/arch/powerpc/boot/dts/mpc832x_mds.dts
index 0793cdf0d46e..49c7d657118a 100644
--- a/arch/powerpc/boot/dts/mpc832x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc832x_mds.dts
@@ -186,7 +186,7 @@
device_type = "par_io";
num-ports = <7>;
- pio3: ucc_pin@03 {
+ pio3: ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
3 4 3 0 2 0 /* MDIO */
@@ -208,7 +208,7 @@
1 12 1 0 1 0 /* TX_EN */
1 13 2 0 1 0>; /* CRS */
};
- pio4: ucc_pin@04 {
+ pio4: ucc_pin@4 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
3 31 2 0 1 0 /* RX_CLK (CLK7) */
@@ -228,7 +228,7 @@
1 30 1 0 1 0 /* TX_EN */
1 31 2 0 1 0>; /* CRS */
};
- pio5: ucc_pin@05 {
+ pio5: ucc_pin@5 {
pio-map = <
/*
* open has
@@ -352,12 +352,12 @@
reg = <0x2320 0x18>;
compatible = "fsl,ucc-mdio";
- phy3: ethernet-phy@03 {
+ phy3: ethernet-phy@3 {
interrupt-parent = <&ipic>;
interrupts = <17 0x8>;
reg = <0x3>;
};
- phy4: ethernet-phy@04 {
+ phy4: ethernet-phy@4 {
interrupt-parent = <&ipic>;
interrupts = <18 0x8>;
reg = <0x4>;
diff --git a/arch/powerpc/boot/dts/mpc832x_rdb.dts b/arch/powerpc/boot/dts/mpc832x_rdb.dts
index 91df1eb16667..647cae14c16d 100644
--- a/arch/powerpc/boot/dts/mpc832x_rdb.dts
+++ b/arch/powerpc/boot/dts/mpc832x_rdb.dts
@@ -175,7 +175,7 @@
gpio-controller;
};
- ucc2pio:ucc_pin@02 {
+ ucc2pio:ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
3 4 3 0 2 0 /* MDIO */
@@ -197,7 +197,7 @@
0 30 1 0 1 0 /* TX_EN */
0 31 2 0 1 0>; /* CRS */
};
- ucc3pio:ucc_pin@03 {
+ ucc3pio:ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0 13 2 0 1 0 /* RX_CLK (CLK9) */
@@ -310,12 +310,12 @@
reg = <0x3120 0x18>;
compatible = "fsl,ucc-mdio";
- phy00:ethernet-phy@00 {
+ phy00:ethernet-phy@0 {
interrupt-parent = <&ipic>;
interrupts = <0>;
reg = <0x0>;
};
- phy04:ethernet-phy@04 {
+ phy04:ethernet-phy@4 {
interrupt-parent = <&ipic>;
interrupts = <0>;
reg = <0x4>;
diff --git a/arch/powerpc/boot/dts/mpc836x_mds.dts b/arch/powerpc/boot/dts/mpc836x_mds.dts
index ecb6ccd3a6aa..539fd9f72eda 100644
--- a/arch/powerpc/boot/dts/mpc836x_mds.dts
+++ b/arch/powerpc/boot/dts/mpc836x_mds.dts
@@ -228,7 +228,7 @@
gpio-controller;
};
- pio1: ucc_pin@01 {
+ pio1: ucc_pin@1 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0 3 1 0 1 0 /* TxD0 */
@@ -255,7 +255,7 @@
2 9 1 0 3 0 /* GTX_CLK - CLK10 */
2 8 2 0 1 0>; /* GTX125 - CLK9 */
};
- pio2: ucc_pin@02 {
+ pio2: ucc_pin@2 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
0 17 1 0 1 0 /* TxD0 */
@@ -393,12 +393,12 @@
reg = <0x2120 0x18>;
compatible = "fsl,ucc-mdio";
- phy0: ethernet-phy@00 {
+ phy0: ethernet-phy@0 {
interrupt-parent = <&ipic>;
interrupts = <17 0x8>;
reg = <0x0>;
};
- phy1: ethernet-phy@01 {
+ phy1: ethernet-phy@1 {
interrupt-parent = <&ipic>;
interrupts = <18 0x8>;
reg = <0x1>;
diff --git a/arch/powerpc/boot/dts/sbc8548-altflash.dts b/arch/powerpc/boot/dts/sbc8548-altflash.dts
index 0b38a0defd2c..8967a56adad4 100644
--- a/arch/powerpc/boot/dts/sbc8548-altflash.dts
+++ b/arch/powerpc/boot/dts/sbc8548-altflash.dts
@@ -40,12 +40,12 @@
compatible = "intel,JS28F128", "cfi-flash";
bank-width = <4>;
device-width = <1>;
- partition@0x0 {
+ partition@0 {
label = "space";
/* FC000000 -> FFEFFFFF */
reg = <0x00000000 0x03f00000>;
};
- partition@0x03f00000 {
+ partition@3f00000 {
label = "bootloader";
/* FFF00000 -> FFFFFFFF */
reg = <0x03f00000 0x00100000>;
@@ -95,12 +95,12 @@
reg = <0x6 0x0 0x800000>;
bank-width = <1>;
device-width = <1>;
- partition@0x0 {
+ partition@0 {
label = "space";
/* EF800000 -> EFF9FFFF */
reg = <0x00000000 0x007a0000>;
};
- partition@0x7a0000 {
+ partition@7a0000 {
label = "bootloader";
/* EFFA0000 -> EFFFFFFF */
reg = <0x007a0000 0x00060000>;
diff --git a/arch/powerpc/boot/dts/sbc8548.dts b/arch/powerpc/boot/dts/sbc8548.dts
index 1df2a0955668..9bdb828a504e 100644
--- a/arch/powerpc/boot/dts/sbc8548.dts
+++ b/arch/powerpc/boot/dts/sbc8548.dts
@@ -38,12 +38,12 @@
reg = <0x0 0x0 0x800000>;
bank-width = <1>;
device-width = <1>;
- partition@0x0 {
+ partition@0 {
label = "space";
/* FF800000 -> FFF9FFFF */
reg = <0x00000000 0x007a0000>;
};
- partition@0x7a0000 {
+ partition@7a0000 {
label = "bootloader";
/* FFFA0000 -> FFFFFFFF */
reg = <0x007a0000 0x00060000>;
@@ -92,12 +92,12 @@
compatible = "intel,JS28F128", "cfi-flash";
bank-width = <4>;
device-width = <1>;
- partition@0x0 {
+ partition@0 {
label = "space";
/* EC000000 -> EFEFFFFF */
reg = <0x00000000 0x03f00000>;
};
- partition@0x03f00000 {
+ partition@3f00000 {
label = "bootloader";
/* EFF00000 -> EFFFFFFF */
reg = <0x03f00000 0x00100000>;
diff --git a/arch/powerpc/boot/dts/wii.dts b/arch/powerpc/boot/dts/wii.dts
index 77528c9a8dbd..17a5babb098d 100644
--- a/arch/powerpc/boot/dts/wii.dts
+++ b/arch/powerpc/boot/dts/wii.dts
@@ -65,14 +65,14 @@
0x0d800000 0x0d800000 0x00800000>;
interrupt-parent = <&PIC0>;
- video@0c002000 {
+ video@c002000 {
compatible = "nintendo,hollywood-vi",
"nintendo,flipper-vi";
reg = <0x0c002000 0x100>;
interrupts = <8>;
};
- processor-interface@0c003000 {
+ processor-interface@c003000 {
compatible = "nintendo,hollywood-pi",
"nintendo,flipper-pi";
reg = <0x0c003000 0x100>;
@@ -84,7 +84,7 @@
};
};
- dsp@0c005000 {
+ dsp@c005000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "nintendo,hollywood-dsp",
@@ -93,14 +93,14 @@
interrupts = <6>;
};
- gamepad-controller@0d006400 {
+ gamepad-controller@d006400 {
compatible = "nintendo,hollywood-si",
"nintendo,flipper-si";
reg = <0x0d006400 0x100>;
interrupts = <3>;
};
- audio@0c006c00 {
+ audio@c006c00 {
compatible = "nintendo,hollywood-ai",
"nintendo,flipper-ai";
reg = <0x0d006c00 0x20>;
@@ -108,7 +108,7 @@
};
/* External Interface bus */
- exi@0d006800 {
+ exi@d006800 {
compatible = "nintendo,hollywood-exi",
"nintendo,flipper-exi";
reg = <0x0d006800 0x40>;
@@ -116,7 +116,7 @@
interrupts = <4>;
};
- usb@0d040000 {
+ usb@d040000 {
compatible = "nintendo,hollywood-usb-ehci",
"usb-ehci";
reg = <0x0d040000 0x100>;
@@ -124,7 +124,7 @@
interrupt-parent = <&PIC1>;
};
- usb@0d050000 {
+ usb@d050000 {
compatible = "nintendo,hollywood-usb-ohci",
"usb-ohci";
reg = <0x0d050000 0x100>;
@@ -132,7 +132,7 @@
interrupt-parent = <&PIC1>;
};
- usb@0d060000 {
+ usb@d060000 {
compatible = "nintendo,hollywood-usb-ohci",
"usb-ohci";
reg = <0x0d060000 0x100>;
@@ -140,7 +140,7 @@
interrupt-parent = <&PIC1>;
};
- sd@0d070000 {
+ sd@d070000 {
compatible = "nintendo,hollywood-sdhci",
"sdhci";
reg = <0x0d070000 0x200>;
@@ -148,7 +148,7 @@
interrupt-parent = <&PIC1>;
};
- sdio@0d080000 {
+ sdio@d080000 {
compatible = "nintendo,hollywood-sdhci",
"sdhci";
reg = <0x0d080000 0x200>;
@@ -156,14 +156,14 @@
interrupt-parent = <&PIC1>;
};
- ipc@0d000000 {
+ ipc@d000000 {
compatible = "nintendo,hollywood-ipc";
reg = <0x0d000000 0x10>;
interrupts = <30>;
interrupt-parent = <&PIC1>;
};
- PIC1: pic1@0d800030 {
+ PIC1: pic1@d800030 {
#interrupt-cells = <1>;
compatible = "nintendo,hollywood-pic";
reg = <0x0d800030 0x10>;
@@ -171,7 +171,7 @@
interrupts = <14>;
};
- GPIO: gpio@0d8000c0 {
+ GPIO: gpio@d8000c0 {
#gpio-cells = <2>;
compatible = "nintendo,hollywood-gpio";
reg = <0x0d8000c0 0x40>;
@@ -203,12 +203,12 @@
*/
};
- control@0d800100 {
+ control@d800100 {
compatible = "nintendo,hollywood-control";
reg = <0x0d800100 0x300>;
};
- disk@0d806000 {
+ disk@d806000 {
compatible = "nintendo,hollywood-di";
reg = <0x0d806000 0x40>;
interrupts = <2>;
--
2.11.0
^ permalink raw reply related
* [PATCH] nios2: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, Ley Foon Tan,
devicetree-u79uwXL29TY76Z2rM5mHXA,
nios2-dev-g9ZBwUv/Ih/yUk5EbOjzuce+I+R0W71w,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney-M3mlKVOIwJVv6pq1l3V1OdBPR1lH4CV8@public.gmane.org>
Suggested-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Mathieu Malaterre <malat-8fiUuRrzOP0dnm+yROfE0A@public.gmane.org>
---
arch/nios2/boot/dts/3c120_devboard.dts | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/nios2/boot/dts/3c120_devboard.dts b/arch/nios2/boot/dts/3c120_devboard.dts
index 36ccdf05837d..56f4b5df6d65 100644
--- a/arch/nios2/boot/dts/3c120_devboard.dts
+++ b/arch/nios2/boot/dts/3c120_devboard.dts
@@ -29,7 +29,7 @@
#address-cells = <1>;
#size-cells = <0>;
- cpu: cpu@0x0 {
+ cpu: cpu@0 {
device_type = "cpu";
compatible = "altr,nios2-1.0";
reg = <0x00000000>;
@@ -69,7 +69,7 @@
compatible = "altr,avalon", "simple-bus";
bus-frequency = <125000000>;
- pb_cpu_to_io: bridge@0x8000000 {
+ pb_cpu_to_io: bridge@8000000 {
compatible = "simple-bus";
reg = <0x08000000 0x00800000>;
#address-cells = <1>;
@@ -83,7 +83,7 @@
<0x00008000 0x08008000 0x00000020>,
<0x00400000 0x08400000 0x00000020>;
- timer_1ms: timer@0x400000 {
+ timer_1ms: timer@400000 {
compatible = "altr,timer-1.0";
reg = <0x00400000 0x00000020>;
interrupt-parent = <&cpu>;
@@ -91,7 +91,7 @@
clock-frequency = <125000000>;
};
- timer_0: timer@0x8000 {
+ timer_0: timer@8000 {
compatible = "altr,timer-1.0";
reg = < 0x00008000 0x00000020 >;
interrupt-parent = < &cpu >;
@@ -99,14 +99,14 @@
clock-frequency = < 125000000 >;
};
- jtag_uart: serial@0x4d50 {
+ jtag_uart: serial@4d50 {
compatible = "altr,juart-1.0";
reg = <0x00004d50 0x00000008>;
interrupt-parent = <&cpu>;
interrupts = <1>;
};
- tse_mac: ethernet@0x4000 {
+ tse_mac: ethernet@4000 {
compatible = "altr,tse-1.0";
reg = <0x00004000 0x00000400>,
<0x00004400 0x00000040>,
@@ -133,7 +133,7 @@
};
};
- uart: serial@0x4c80 {
+ uart: serial@4c80 {
compatible = "altr,uart-1.0";
reg = <0x00004c80 0x00000020>;
interrupt-parent = <&cpu>;
@@ -143,7 +143,7 @@
};
};
- cfi_flash_64m: flash@0x0 {
+ cfi_flash_64m: flash@0 {
compatible = "cfi-flash";
reg = <0x00000000 0x04000000>;
bank-width = <2>;
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH] mips: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Paul Burton, Mark Rutland, Ralf Baechle,
Philippe Ombredanne, Paul Cercueil, Thomas Gleixner,
Greg Kroah-Hartman, Harvey Hunt, linux-mips, devicetree,
linux-kernel
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/mips/boot/dts/img/boston.dts | 2 +-
arch/mips/boot/dts/ingenic/ci20.dts | 8 ++++----
2 files changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/mips/boot/dts/img/boston.dts b/arch/mips/boot/dts/img/boston.dts
index 2cd49b60e030..1bd105428f61 100644
--- a/arch/mips/boot/dts/img/boston.dts
+++ b/arch/mips/boot/dts/img/boston.dts
@@ -157,7 +157,7 @@
#address-cells = <1>;
#size-cells = <0>;
- rtc@0x68 {
+ rtc@68 {
compatible = "st,m41t81s";
reg = <0x68>;
};
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index a4cc52214dbd..7d5e49e40b0d 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -110,22 +110,22 @@
reg = <0x0 0x0 0x0 0x800000>;
};
- partition@0x800000 {
+ partition@800000 {
label = "u-boot";
reg = <0x0 0x800000 0x0 0x200000>;
};
- partition@0xa00000 {
+ partition@a00000 {
label = "u-boot-env";
reg = <0x0 0xa00000 0x0 0x200000>;
};
- partition@0xc00000 {
+ partition@c00000 {
label = "boot";
reg = <0x0 0xc00000 0x0 0x4000000>;
};
- partition@0x8c00000 {
+ partition@8c00000 {
label = "system";
reg = <0x0 0x4c00000 0x1 0xfb400000>;
};
--
2.11.0
^ permalink raw reply related
* [PATCH] metag: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, James Hogan,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-metag-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney-M3mlKVOIwJVv6pq1l3V1OdBPR1lH4CV8@public.gmane.org>
Suggested-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Mathieu Malaterre <malat-8fiUuRrzOP0dnm+yROfE0A@public.gmane.org>
---
arch/metag/boot/dts/tz1090.dtsi | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/arch/metag/boot/dts/tz1090.dtsi b/arch/metag/boot/dts/tz1090.dtsi
index 24ea7d2e9138..a3a3be7796f1 100644
--- a/arch/metag/boot/dts/tz1090.dtsi
+++ b/arch/metag/boot/dts/tz1090.dtsi
@@ -28,7 +28,7 @@
#size-cells = <1>;
ranges;
- pdc: pdc@0x02006000 {
+ pdc: pdc@2006000 {
interrupt-controller;
#interrupt-cells = <2>;
@@ -44,19 +44,19 @@
<31 IRQ_TYPE_LEVEL_HIGH>; /* Perip 2 (WDT) */
};
- pinctrl: pinctrl@02005800 {
+ pinctrl: pinctrl@2005800 {
#gpio-range-cells = <3>;
compatible = "img,tz1090-pinctrl";
reg = <0x02005800 0xe4>;
};
- pdc_pinctrl: pinctrl@02006500 {
+ pdc_pinctrl: pinctrl@2006500 {
#gpio-range-cells = <3>;
compatible = "img,tz1090-pdc-pinctrl";
reg = <0x02006500 0x100>;
};
- gpios: gpios@02005800 {
+ gpios: gpios@2005800 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "img,tz1090-gpio";
@@ -91,7 +91,7 @@
};
};
- pdc_gpios: gpios@02006500 {
+ pdc_gpios: gpios@2006500 {
gpio-controller;
#gpio-cells = <2>;
--
2.11.0
^ permalink raw reply related
* [PATCH] c6x: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, Mark Salter, Aurelien Jacquiot,
devicetree, linux-c6x-dev, linux-kernel
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/c6x/boot/dts/dsk6455.dts | 2 +-
arch/c6x/boot/dts/tms320c6455.dtsi | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/c6x/boot/dts/dsk6455.dts b/arch/c6x/boot/dts/dsk6455.dts
index 2b71f800618d..3012f44e9357 100644
--- a/arch/c6x/boot/dts/dsk6455.dts
+++ b/arch/c6x/boot/dts/dsk6455.dts
@@ -55,7 +55,7 @@
interrupts = < 69 >;
};
- clock-controller@029a0000 {
+ clock-controller@29a0000 {
clock-frequency = <50000000>;
};
};
diff --git a/arch/c6x/boot/dts/tms320c6455.dtsi b/arch/c6x/boot/dts/tms320c6455.dtsi
index 0b21cb30343b..b5c36fb351db 100644
--- a/arch/c6x/boot/dts/tms320c6455.dtsi
+++ b/arch/c6x/boot/dts/tms320c6455.dtsi
@@ -68,7 +68,7 @@
ti,dscr-dev-enable = <4>;
};
- clock-controller@029a0000 {
+ clock-controller@29a0000 {
compatible = "ti,c6455-pll", "ti,c64x+pll";
reg = <0x029a0000 0x200>;
ti,c64x+pll-bypass-delay = <1440>;
--
2.11.0
^ permalink raw reply related
* [PATCH] arm64: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Wei Xu, Mark Rutland, Catalin Marinas,
Will Deacon, Matthias Brugger, Andy Gross, David Brown, Kees Cook,
Anton Vorontsov, Colin Cross, Tony Luck, linux-arm-kernel,
devicetree, linux-kernel, linux-mediatek, linux-arm-msm,
linux-soc
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts | 2 +-
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 2 +-
arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 6 +++---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 6 +++---
4 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 3aee6123d161..3f5ff76109be 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -51,7 +51,7 @@
#size-cells = <2>;
ranges;
- ramoops@0x21f00000 {
+ ramoops@21f00000 {
compatible = "ramoops";
reg = <0x0 0x21f00000 0x0 0x00100000>;
record-size = <0x00020000>;
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 26396ef53bde..0446b122a6e2 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -249,7 +249,7 @@
reg = <0 0x10005000 0 0x1000>;
};
- pio: pinctrl@0x10005000 {
+ pio: pinctrl@10005000 {
compatible = "mediatek,mt8173-pinctrl";
reg = <0 0x1000b000 0 0x1000>;
mediatek,pctl-regmap = <&syscfg_pctl_a>;
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
index 492a011f14f6..1c8f1b86472d 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi
@@ -140,16 +140,16 @@
};
agnoc@0 {
- qcom,pcie@00600000 {
+ qcom,pcie@600000 {
perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>;
};
- qcom,pcie@00608000 {
+ qcom,pcie@608000 {
status = "okay";
perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>;
};
- qcom,pcie@00610000 {
+ qcom,pcie@610000 {
status = "okay";
perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>;
};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 4b2afcc4fdf4..0a6f7952bbb1 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -840,7 +840,7 @@
#size-cells = <1>;
ranges;
- pcie0: qcom,pcie@00600000 {
+ pcie0: qcom,pcie@600000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
status = "disabled";
power-domains = <&gcc PCIE0_GDSC>;
@@ -893,7 +893,7 @@
};
- pcie1: qcom,pcie@00608000 {
+ pcie1: qcom,pcie@608000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
power-domains = <&gcc PCIE1_GDSC>;
bus-range = <0x00 0xff>;
@@ -946,7 +946,7 @@
"bus_slave";
};
- pcie2: qcom,pcie@00610000 {
+ pcie2: qcom,pcie@610000 {
compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
power-domains = <&gcc PCIE2_GDSC>;
bus-range = <0x00 0xff>;
--
2.11.0
^ permalink raw reply related
* [PATCH] arm: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Benoît Cousson, Tony Lindgren,
Mark Rutland, Russell King, Jesper Nilsson, Lars Persson,
Niklas Cassel, Nicolas Ferre, Alexandre Belloni, Ray Jui,
Scott Branden, Jon Mason,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w, Florian Fainelli,
Sekhar Nori, Kevin Hilman, Kukjin Kim, Krzysztof Kozlowski
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney-M3mlKVOIwJVv6pq1l3V1OdBPR1lH4CV8@public.gmane.org>
Suggested-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Mathieu Malaterre <malat-8fiUuRrzOP0dnm+yROfE0A@public.gmane.org>
---
arch/arm/boot/dts/am3517.dtsi | 4 +--
arch/arm/boot/dts/arm-realview-eb.dtsi | 18 +++++++-------
arch/arm/boot/dts/arm-realview-pb1176.dts | 18 +++++++-------
arch/arm/boot/dts/arm-realview-pb11mp.dts | 18 +++++++-------
arch/arm/boot/dts/arm-realview-pbx.dtsi | 18 +++++++-------
arch/arm/boot/dts/artpec6.dtsi | 2 +-
arch/arm/boot/dts/at91sam9261.dtsi | 2 +-
arch/arm/boot/dts/at91sam9261ek.dts | 2 +-
arch/arm/boot/dts/at91sam9263.dtsi | 2 +-
arch/arm/boot/dts/at91sam9263ek.dts | 2 +-
arch/arm/boot/dts/at91sam9g25ek.dts | 2 +-
arch/arm/boot/dts/at91sam9g45.dtsi | 2 +-
arch/arm/boot/dts/at91sam9m10g45ek.dts | 2 +-
arch/arm/boot/dts/atlas7.dtsi | 12 ++++-----
arch/arm/boot/dts/bcm11351.dtsi | 2 +-
arch/arm/boot/dts/bcm21664.dtsi | 2 +-
arch/arm/boot/dts/bcm283x.dtsi | 2 +-
arch/arm/boot/dts/da850-lcdk.dts | 4 +--
arch/arm/boot/dts/dm8148-evm.dts | 8 +++---
arch/arm/boot/dts/dm8168-evm.dts | 8 +++---
arch/arm/boot/dts/dra62x-j5eco-evm.dts | 8 +++---
arch/arm/boot/dts/exynos5420.dtsi | 36 +++++++++++++--------------
arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 2 +-
arch/arm/boot/dts/imx7d.dtsi | 2 +-
arch/arm/boot/dts/keystone-k2e-netcp.dtsi | 2 +-
arch/arm/boot/dts/keystone-k2hk-netcp.dtsi | 2 +-
arch/arm/boot/dts/keystone-k2l-netcp.dtsi | 2 +-
arch/arm/boot/dts/omap3-cm-t3x.dtsi | 8 +++---
arch/arm/boot/dts/omap3-evm-37xx.dts | 8 +++---
arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 8 +++---
arch/arm/boot/dts/s3c2416.dtsi | 2 +-
arch/arm/boot/dts/sama5d3xmb.dtsi | 2 +-
arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 2 +-
arch/arm/boot/dts/socfpga.dtsi | 2 +-
arch/arm/boot/dts/spear300.dtsi | 2 +-
arch/arm/boot/dts/spear310.dtsi | 2 +-
arch/arm/boot/dts/spear320.dtsi | 2 +-
arch/arm/boot/dts/versatile-ab.dts | 16 ++++++------
arch/arm/boot/dts/zx296702.dtsi | 20 +++++++--------
39 files changed, 129 insertions(+), 129 deletions(-)
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index 00da3f2c4072..76994165fb3a 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -26,7 +26,7 @@
interrupt-names = "mc";
};
- davinci_emac: ethernet@0x5c000000 {
+ davinci_emac: ethernet@5c000000 {
compatible = "ti,am3517-emac";
ti,hwmods = "davinci_emac";
status = "disabled";
@@ -41,7 +41,7 @@
local-mac-address = [ 00 00 00 00 00 00 ];
};
- davinci_mdio: ethernet@0x5c030000 {
+ davinci_mdio: ethernet@5c030000 {
compatible = "ti,davinci_mdio";
ti,hwmods = "davinci_mdio";
status = "disabled";
diff --git a/arch/arm/boot/dts/arm-realview-eb.dtsi b/arch/arm/boot/dts/arm-realview-eb.dtsi
index e2e9599596e2..f92fb6debc13 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm-realview-eb.dtsi
@@ -154,7 +154,7 @@
compatible = "arm,realview-eb-syscon", "syscon", "simple-mfd";
reg = <0x10000000 0x1000>;
- led@08.0 {
+ led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
@@ -162,7 +162,7 @@
linux,default-trigger = "heartbeat";
default-state = "on";
};
- led@08.1 {
+ led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
@@ -170,7 +170,7 @@
linux,default-trigger = "mmc0";
default-state = "off";
};
- led@08.2 {
+ led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
@@ -178,42 +178,42 @@
linux,default-trigger = "cpu0";
default-state = "off";
};
- led@08.3 {
+ led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
label = "versatile:3";
default-state = "off";
};
- led@08.4 {
+ led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
label = "versatile:4";
default-state = "off";
};
- led@08.5 {
+ led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
label = "versatile:5";
default-state = "off";
};
- led@08.6 {
+ led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
- led@08.7 {
+ led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
label = "versatile:7";
default-state = "off";
};
- oscclk0: osc0@0c {
+ oscclk0: osc0@c {
compatible = "arm,syscon-icst307";
#clock-cells = <0>;
lock-offset = <0x20>;
diff --git a/arch/arm/boot/dts/arm-realview-pb1176.dts b/arch/arm/boot/dts/arm-realview-pb1176.dts
index c789564f2803..c918949d7c21 100644
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm-realview-pb1176.dts
@@ -172,7 +172,7 @@
compatible = "arm,realview-pb1176-syscon", "syscon", "simple-mfd";
reg = <0x10000000 0x1000>;
- led@08.0 {
+ led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
@@ -180,7 +180,7 @@
linux,default-trigger = "heartbeat";
default-state = "on";
};
- led@08.1 {
+ led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
@@ -188,7 +188,7 @@
linux,default-trigger = "mmc0";
default-state = "off";
};
- led@08.2 {
+ led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
@@ -196,42 +196,42 @@
linux,default-trigger = "cpu0";
default-state = "off";
};
- led@08.3 {
+ led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
label = "versatile:3";
default-state = "off";
};
- led@08.4 {
+ led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
label = "versatile:4";
default-state = "off";
};
- led@08.5 {
+ led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
label = "versatile:5";
default-state = "off";
};
- led@08.6 {
+ led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
- led@08.7 {
+ led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
label = "versatile:7";
default-state = "off";
};
- oscclk0: osc0@0c {
+ oscclk0: osc0@c {
compatible = "arm,syscon-icst307";
#clock-cells = <0>;
lock-offset = <0x20>;
diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts
index 3944765ac4b0..12c3fb69038a 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts
@@ -253,7 +253,7 @@
compatible = "arm,realview-pb11mp-syscon", "syscon", "simple-mfd";
reg = <0x10000000 0x1000>;
- led@08.0 {
+ led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
@@ -261,7 +261,7 @@
linux,default-trigger = "heartbeat";
default-state = "on";
};
- led@08.1 {
+ led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
@@ -269,7 +269,7 @@
linux,default-trigger = "mmc0";
default-state = "off";
};
- led@08.2 {
+ led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
@@ -277,7 +277,7 @@
linux,default-trigger = "cpu0";
default-state = "off";
};
- led@08.3 {
+ led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
@@ -285,7 +285,7 @@
linux,default-trigger = "cpu1";
default-state = "off";
};
- led@08.4 {
+ led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
@@ -293,7 +293,7 @@
linux,default-trigger = "cpu2";
default-state = "off";
};
- led@08.5 {
+ led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
@@ -301,14 +301,14 @@
linux,default-trigger = "cpu3";
default-state = "off";
};
- led@08.6 {
+ led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
- led@08.7 {
+ led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
@@ -316,7 +316,7 @@
default-state = "off";
};
- oscclk0: osc0@0c {
+ oscclk0: osc0@c {
compatible = "arm,syscon-icst307";
#clock-cells = <0>;
lock-offset = <0x20>;
diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm-realview-pbx.dtsi
index aeb49c4bd773..ae080739229e 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
@@ -169,7 +169,7 @@
compatible = "arm,realview-pbx-syscon", "syscon", "simple-mfd";
reg = <0x10000000 0x1000>;
- led@08.0 {
+ led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
@@ -177,7 +177,7 @@
linux,default-trigger = "heartbeat";
default-state = "on";
};
- led@08.1 {
+ led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
@@ -185,7 +185,7 @@
linux,default-trigger = "mmc0";
default-state = "off";
};
- led@08.2 {
+ led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
@@ -193,42 +193,42 @@
linux,default-trigger = "cpu0";
default-state = "off";
};
- led@08.3 {
+ led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
label = "versatile:3";
default-state = "off";
};
- led@08.4 {
+ led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
label = "versatile:4";
default-state = "off";
};
- led@08.5 {
+ led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
label = "versatile:5";
default-state = "off";
};
- led@08.6 {
+ led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
- led@08.7 {
+ led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
label = "versatile:7";
default-state = "off";
};
- oscclk0: osc0@0c {
+ oscclk0: osc0@c {
compatible = "arm,syscon-icst307";
#clock-cells = <0>;
lock-offset = <0x20>;
diff --git a/arch/arm/boot/dts/artpec6.dtsi b/arch/arm/boot/dts/artpec6.dtsi
index 2ed11773048d..71e0e75e986b 100644
--- a/arch/arm/boot/dts/artpec6.dtsi
+++ b/arch/arm/boot/dts/artpec6.dtsi
@@ -98,7 +98,7 @@
clock-frequency = <125000000>;
};
- clkctrl: clkctrl@0xf8000000 {
+ clkctrl: clkctrl@f8000000 {
#clock-cells = <1>;
compatible = "axis,artpec6-clkctrl";
reg = <0xf8000000 0x48>;
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index 66876019101d..eb186245fb4c 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -80,7 +80,7 @@
status = "disabled";
};
- fb0: fb@0x00600000 {
+ fb0: fb@600000 {
compatible = "atmel,at91sam9261-lcdc";
reg = <0x00600000 0x1000>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH 3>;
diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts
index 960d6940ebf6..9733db3f739b 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/at91sam9261ek.dts
@@ -36,7 +36,7 @@
status = "okay";
};
- fb0: fb@0x00600000 {
+ fb0: fb@600000 {
display = <&display0>;
atmel,power-control-gpio = <&pioA 12 GPIO_ACTIVE_LOW>;
status = "okay";
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index e54f14d36b6f..a26f7ada429d 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -999,7 +999,7 @@
};
};
- fb0: fb@0x00700000 {
+ fb0: fb@700000 {
compatible = "atmel,at91sam9263-lcdc";
reg = <0x00700000 0x1000>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 3>;
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 5a2e1af793f5..f095b5d4d410 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -95,7 +95,7 @@
};
};
- fb0: fb@0x00700000 {
+ fb0: fb@700000 {
display = <&display0>;
status = "okay";
diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts
index 91a71774472e..31fecc2cdaf9 100644
--- a/arch/arm/boot/dts/at91sam9g25ek.dts
+++ b/arch/arm/boot/dts/at91sam9g25ek.dts
@@ -25,7 +25,7 @@
};
i2c0: i2c@f8010000 {
- ov2640: camera@0x30 {
+ ov2640: camera@30 {
compatible = "ovti,ov2640";
reg = <0x30>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 2b127ca7aaa0..98348ebd6488 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -1302,7 +1302,7 @@
};
};
- fb0: fb@0x00500000 {
+ fb0: fb@500000 {
compatible = "atmel,at91sam9g45-lcdc";
reg = <0x00500000 0x1000>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 3>;
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index e922552a04cb..d793451ee04c 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -220,7 +220,7 @@
};
};
- fb0: fb@0x00500000 {
+ fb0: fb@500000 {
display = <&display0>;
status = "okay";
diff --git a/arch/arm/boot/dts/atlas7.dtsi b/arch/arm/boot/dts/atlas7.dtsi
index 83449b33de6b..920d22882f21 100644
--- a/arch/arm/boot/dts/atlas7.dtsi
+++ b/arch/arm/boot/dts/atlas7.dtsi
@@ -1170,7 +1170,7 @@
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x13240000 0x13240000 0x00010000>;
- pmipc@0x13240000 {
+ pmipc@13240000 {
compatible = "sirf,atlas7-pmipc";
reg = <0x13240000 0x00010000>;
};
@@ -1265,7 +1265,7 @@
#dma-cells = <1>;
};
- gnssmfw@0x18100000 {
+ gnssmfw@18100000 {
compatible = "sirf,nocfw-gnssm";
reg = <0x18100000 0x3000>;
};
@@ -1374,7 +1374,7 @@
<0x13010000 0x13010000 0x1400>,
<0x13010800 0x13010800 0x100>,
<0x13011000 0x13011000 0x100>;
- gpum@0x13000000 {
+ gpum@13000000 {
compatible = "sirf,nocfw-gpum";
reg = <0x13000000 0x3000>;
};
@@ -1396,7 +1396,7 @@
#dma-cells = <1>;
#dma-channels = <1>;
};
- sdr@0x13010000 {
+ sdr@13010000 {
compatible = "sirf,atlas7-sdr";
reg = <0x13010000 0x1400>;
interrupts = <0 7 0>,
@@ -1780,7 +1780,7 @@
interrupts = <0 105 0>;
};
- memory-controller@0x10800000 {
+ memory-controller@10800000 {
compatible = "sirf,atlas7-memc";
reg = <0x10800000 0x2000>;
};
@@ -1896,7 +1896,7 @@
#size-cells = <0>;
};
- retain@0x188D0000 {
+ retain@188d0000 {
compatible = "sirf,atlas7-retain";
reg = <0x188D0000 0x1000>;
};
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 18045c38bcf1..db7cded1b7ad 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -55,7 +55,7 @@
<0x3ff00100 0x100>;
};
- smc@0x3404c000 {
+ smc@3404c000 {
compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
reg = <0x3404c000 0x400>; /* 1 KiB in SRAM */
};
diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/bcm21664.dtsi
index 6dde95f21cef..266f2611dc22 100644
--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ b/arch/arm/boot/dts/bcm21664.dtsi
@@ -55,7 +55,7 @@
<0x3ff00100 0x100>;
};
- smc@0x3404e000 {
+ smc@3404e000 {
compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
};
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index dcde93c85c2d..2ee4f04ea9d4 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -464,7 +464,7 @@
status = "disabled";
};
- aux: aux@0x7e215000 {
+ aux: aux@7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
reg = <0x7e215000 0x8>;
diff --git a/arch/arm/boot/dts/da850-lcdk.dts b/arch/arm/boot/dts/da850-lcdk.dts
index eed89e659143..a1f4d6d5a569 100644
--- a/arch/arm/boot/dts/da850-lcdk.dts
+++ b/arch/arm/boot/dts/da850-lcdk.dts
@@ -293,12 +293,12 @@
label = "u-boot env";
reg = <0 0x020000>;
};
- partition@0x020000 {
+ partition@20000 {
/* The LCDK defaults to booting from this partition */
label = "u-boot";
reg = <0x020000 0x080000>;
};
- partition@0x0a0000 {
+ partition@a0000 {
label = "free space";
reg = <0x0a0000 0>;
};
diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts
index d6657b3bae84..7747a5b9657f 100644
--- a/arch/arm/boot/dts/dm8148-evm.dts
+++ b/arch/arm/boot/dts/dm8148-evm.dts
@@ -74,19 +74,19 @@
label = "X-Loader";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x80000 0x1c0000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x240000 0x40000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x780000 0xf880000>;
};
diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index c72a2132aa82..85dd3c703dff 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -158,19 +158,19 @@
label = "X-Loader";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x80000 0x1c0000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x240000 0x40000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x780000 0xf880000>;
};
diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
index 155eb32ee213..fee0547f7302 100644
--- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts
+++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
@@ -74,19 +74,19 @@
label = "X-Loader";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x80000 0x1c0000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x240000 0x40000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x780000 0xf880000>;
};
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index 8aa2cc7aa125..05ddbcf4413b 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -752,7 +752,7 @@
#include "exynos5420-tmu-sensor-conf.dtsi"
};
- sysmmu_g2dr: sysmmu@0x10A60000 {
+ sysmmu_g2dr: sysmmu@10a60000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x10A60000 0x1000>;
interrupt-parent = <&combiner>;
@@ -762,7 +762,7 @@
#iommu-cells = <0>;
};
- sysmmu_g2dw: sysmmu@0x10A70000 {
+ sysmmu_g2dw: sysmmu@10a70000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x10A70000 0x1000>;
interrupt-parent = <&combiner>;
@@ -772,7 +772,7 @@
#iommu-cells = <0>;
};
- sysmmu_tv: sysmmu@0x14650000 {
+ sysmmu_tv: sysmmu@14650000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x14650000 0x1000>;
interrupt-parent = <&combiner>;
@@ -783,7 +783,7 @@
#iommu-cells = <0>;
};
- sysmmu_gscl0: sysmmu@0x13E80000 {
+ sysmmu_gscl0: sysmmu@13e80000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x13E80000 0x1000>;
interrupt-parent = <&combiner>;
@@ -794,7 +794,7 @@
#iommu-cells = <0>;
};
- sysmmu_gscl1: sysmmu@0x13E90000 {
+ sysmmu_gscl1: sysmmu@13e90000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x13E90000 0x1000>;
interrupt-parent = <&combiner>;
@@ -805,7 +805,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler0r: sysmmu@0x12880000 {
+ sysmmu_scaler0r: sysmmu@12880000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x12880000 0x1000>;
interrupt-parent = <&combiner>;
@@ -815,7 +815,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler1r: sysmmu@0x12890000 {
+ sysmmu_scaler1r: sysmmu@12890000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x12890000 0x1000>;
interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
@@ -824,7 +824,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler2r: sysmmu@0x128A0000 {
+ sysmmu_scaler2r: sysmmu@128a0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128A0000 0x1000>;
interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
@@ -833,7 +833,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler0w: sysmmu@0x128C0000 {
+ sysmmu_scaler0w: sysmmu@128c0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128C0000 0x1000>;
interrupt-parent = <&combiner>;
@@ -843,7 +843,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler1w: sysmmu@0x128D0000 {
+ sysmmu_scaler1w: sysmmu@128d0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128D0000 0x1000>;
interrupt-parent = <&combiner>;
@@ -853,7 +853,7 @@
#iommu-cells = <0>;
};
- sysmmu_scaler2w: sysmmu@0x128E0000 {
+ sysmmu_scaler2w: sysmmu@128e0000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x128E0000 0x1000>;
interrupt-parent = <&combiner>;
@@ -863,7 +863,7 @@
#iommu-cells = <0>;
};
- sysmmu_rotator: sysmmu@0x11D40000 {
+ sysmmu_rotator: sysmmu@11d40000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11D40000 0x1000>;
interrupt-parent = <&combiner>;
@@ -873,7 +873,7 @@
#iommu-cells = <0>;
};
- sysmmu_jpeg0: sysmmu@0x11F10000 {
+ sysmmu_jpeg0: sysmmu@11f10000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11F10000 0x1000>;
interrupt-parent = <&combiner>;
@@ -883,7 +883,7 @@
#iommu-cells = <0>;
};
- sysmmu_jpeg1: sysmmu@0x11F20000 {
+ sysmmu_jpeg1: sysmmu@11f20000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11F20000 0x1000>;
interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
@@ -892,7 +892,7 @@
#iommu-cells = <0>;
};
- sysmmu_mfc_l: sysmmu@0x11200000 {
+ sysmmu_mfc_l: sysmmu@11200000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11200000 0x1000>;
interrupt-parent = <&combiner>;
@@ -903,7 +903,7 @@
#iommu-cells = <0>;
};
- sysmmu_mfc_r: sysmmu@0x11210000 {
+ sysmmu_mfc_r: sysmmu@11210000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x11210000 0x1000>;
interrupt-parent = <&combiner>;
@@ -914,7 +914,7 @@
#iommu-cells = <0>;
};
- sysmmu_fimd1_0: sysmmu@0x14640000 {
+ sysmmu_fimd1_0: sysmmu@14640000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x14640000 0x1000>;
interrupt-parent = <&combiner>;
@@ -925,7 +925,7 @@
#iommu-cells = <0>;
};
- sysmmu_fimd1_1: sysmmu@0x14680000 {
+ sysmmu_fimd1_1: sysmmu@14680000 {
compatible = "samsung,exynos-sysmmu";
reg = <0x14680000 0x1000>;
interrupt-parent = <&combiner>;
diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index a5b8d0f0877e..353428fe10c4 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -26,7 +26,7 @@
stdout-path = "serial2:115200n8";
};
- firmware@02073000 {
+ firmware@2073000 {
compatible = "samsung,secure-firmware";
reg = <0x02073000 0x1000>;
};
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index 4d308d17f040..369d5a166b3e 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -129,7 +129,7 @@
status = "disabled";
};
- pcie: pcie@0x33800000 {
+ pcie: pcie@33800000 {
compatible = "fsl,imx7d-pcie", "snps,dw-pcie";
reg = <0x33800000 0x4000>,
<0x4ff00000 0x80000>;
diff --git a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
index ba828cb59587..940b64935bde 100644
--- a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
@@ -98,7 +98,7 @@ qmss: qmss@2a40000 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- pdsp0@0x2a10000 {
+ pdsp0@2a10000 {
reg = <0x2a10000 0x1000 /*iram */
0x2a0f000 0x100 /*reg*/
0x2a0c000 0x3c8 /*intd */
diff --git a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
index a5ac845464bf..ed7287a274a0 100644
--- a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
@@ -115,7 +115,7 @@ qmss: qmss@2a40000 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- pdsp0@0x2a10000 {
+ pdsp0@2a10000 {
reg = <0x2a10000 0x1000 /*iram */
0x2a0f000 0x100 /*reg*/
0x2a0c000 0x3c8 /*intd */
diff --git a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
index 66f615a74118..b6af5f78e498 100644
--- a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
@@ -97,7 +97,7 @@ qmss: qmss@2a40000 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
- pdsp0@0x2a10000 {
+ pdsp0@2a10000 {
reg = <0x2a10000 0x1000 /*iram */
0x2a0f000 0x100 /*reg*/
0x2a0c000 0x3c8 /*intd */
diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi
index ab6003fe5a43..9dcb18d22cde 100644
--- a/arch/arm/boot/dts/omap3-cm-t3x.dtsi
+++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi
@@ -306,19 +306,19 @@
label = "xloader";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "uboot";
reg = <0x80000 0x1e0000>;
};
- partition@0x260000 {
+ partition@260000 {
label = "uboot environment";
reg = <0x260000 0x40000>;
};
- partition@0x2a0000 {
+ partition@2a0000 {
label = "linux";
reg = <0x2a0000 0x400000>;
};
- partition@0x6a0000 {
+ partition@6a0000 {
label = "rootfs";
reg = <0x6a0000 0x1f880000>;
};
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
index 5a4ba0aea447..a14303b09ae2 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -90,19 +90,19 @@
label = "X-Loader";
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "U-Boot";
reg = <0x80000 0x1c0000>;
};
- partition@0x1c0000 {
+ partition@1c0000 {
label = "Environment";
reg = <0x240000 0x40000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "Kernel";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "Filesystem";
reg = <0x780000 0x1f880000>;
};
diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
index 7ada1e93e166..cf7a2a72348d 100644
--- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
+++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
@@ -405,22 +405,22 @@
reg = <0 0x80000>;
};
- partition@0x80000 {
+ partition@80000 {
label = "u-boot";
reg = <0x80000 0x1e0000>;
};
- partition@0x260000 {
+ partition@260000 {
label = "u-boot-environment";
reg = <0x260000 0x20000>;
};
- partition@0x280000 {
+ partition@280000 {
label = "kernel";
reg = <0x280000 0x500000>;
};
- partition@0x780000 {
+ partition@780000 {
label = "filesystem";
reg = <0x780000 0xf880000>;
};
diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi
index 80f007550324..66840f02a618 100644
--- a/arch/arm/boot/dts/s3c2416.dtsi
+++ b/arch/arm/boot/dts/s3c2416.dtsi
@@ -33,7 +33,7 @@
compatible = "samsung,s3c2416-irq";
};
- clocks: clock-controller@0x4c000000 {
+ clocks: clock-controller@4c000000 {
compatible = "samsung,s3c2416-clock";
reg = <0x4c000000 0x40>;
#clock-cells = <1>;
diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi
index 7f55050dd405..ef0f2d049e15 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
@@ -53,7 +53,7 @@
};
i2c1: i2c@f0018000 {
- ov2640: camera@0x30 {
+ ov2640: camera@30 {
compatible = "ovti,ov2640";
reg = <0x30>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
index 83e3d3e08fd4..97e171db5970 100644
--- a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -88,7 +88,7 @@
};
i2c1: i2c@f0018000 {
- ov2640: camera@0x30 {
+ ov2640: camera@30 {
compatible = "ovti,ov2640";
reg = <0x30>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index 7e24dc8e82d4..36f87eb389b1 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -724,7 +724,7 @@
arm,prefetch-offset = <7>;
};
- l3regs@0xff800000 {
+ l3regs@ff800000 {
compatible = "altr,l3regs", "syscon";
reg = <0xff800000 0x1000>;
};
diff --git a/arch/arm/boot/dts/spear300.dtsi b/arch/arm/boot/dts/spear300.dtsi
index f4e92e599729..266fefa67223 100644
--- a/arch/arm/boot/dts/spear300.dtsi
+++ b/arch/arm/boot/dts/spear300.dtsi
@@ -52,7 +52,7 @@
status = "disabled";
};
- shirq: interrupt-controller@0x50000000 {
+ shirq: interrupt-controller@50000000 {
compatible = "st,spear300-shirq";
reg = <0x50000000 0x1000>;
interrupts = <28>;
diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi
index da210b454753..f995ecf09acf 100644
--- a/arch/arm/boot/dts/spear310.dtsi
+++ b/arch/arm/boot/dts/spear310.dtsi
@@ -40,7 +40,7 @@
status = "disabled";
};
- shirq: interrupt-controller@0xb4000000 {
+ shirq: interrupt-controller@b4000000 {
compatible = "st,spear310-shirq";
reg = <0xb4000000 0x1000>;
interrupts = <28 29 30 1>;
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi
index 22be6e5edaac..2a062a3ee139 100644
--- a/arch/arm/boot/dts/spear320.dtsi
+++ b/arch/arm/boot/dts/spear320.dtsi
@@ -55,7 +55,7 @@
status = "disabled";
};
- shirq: interrupt-controller@0xb3000000 {
+ shirq: interrupt-controller@b3000000 {
compatible = "st,spear320-shirq";
reg = <0xb3000000 0x1000>;
interrupts = <30 28 29 1>;
diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/versatile-ab.dts
index 4a51612996bc..8b0ad47e7b1f 100644
--- a/arch/arm/boot/dts/versatile-ab.dts
+++ b/arch/arm/boot/dts/versatile-ab.dts
@@ -34,7 +34,7 @@
compatible = "arm,core-module-versatile", "syscon", "simple-mfd";
reg = <0x10000000 0x200>;
- led@08.0 {
+ led@8.0 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x01>;
@@ -42,7 +42,7 @@
linux,default-trigger = "heartbeat";
default-state = "on";
};
- led@08.1 {
+ led@8.1 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x02>;
@@ -50,7 +50,7 @@
linux,default-trigger = "mmc0";
default-state = "off";
};
- led@08.2 {
+ led@8.2 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x04>;
@@ -58,35 +58,35 @@
linux,default-trigger = "cpu0";
default-state = "off";
};
- led@08.3 {
+ led@8.3 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x08>;
label = "versatile:3";
default-state = "off";
};
- led@08.4 {
+ led@8.4 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x10>;
label = "versatile:4";
default-state = "off";
};
- led@08.5 {
+ led@8.5 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x20>;
label = "versatile:5";
default-state = "off";
};
- led@08.6 {
+ led@8.6 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x40>;
label = "versatile:6";
default-state = "off";
};
- led@08.7 {
+ led@8.7 {
compatible = "register-bit-led";
offset = <0x08>;
mask = <0x80>;
diff --git a/arch/arm/boot/dts/zx296702.dtsi b/arch/arm/boot/dts/zx296702.dtsi
index 8a74efdb6360..240e7a23d81f 100644
--- a/arch/arm/boot/dts/zx296702.dtsi
+++ b/arch/arm/boot/dts/zx296702.dtsi
@@ -56,7 +56,7 @@
clocks = <&topclk ZX296702_A9_PERIPHCLK>;
};
- l2cc: l2-cache-controller@0x00c00000 {
+ l2cc: l2-cache-controller@c00000 {
compatible = "arm,pl310-cache";
reg = <0x00c00000 0x1000>;
cache-unified;
@@ -67,30 +67,30 @@
arm,double-linefill-incr = <0>;
};
- pcu: pcu@0xa0008000 {
+ pcu: pcu@a0008000 {
compatible = "zte,zx296702-pcu";
reg = <0xa0008000 0x1000>;
};
- topclk: topclk@0x09800000 {
+ topclk: topclk@9800000 {
compatible = "zte,zx296702-topcrm-clk";
reg = <0x09800000 0x1000>;
#clock-cells = <1>;
};
- lsp1clk: lsp1clk@0x09400000 {
+ lsp1clk: lsp1clk@9400000 {
compatible = "zte,zx296702-lsp1crpm-clk";
reg = <0x09400000 0x1000>;
#clock-cells = <1>;
};
- lsp0clk: lsp0clk@0x0b000000 {
+ lsp0clk: lsp0clk@b000000 {
compatible = "zte,zx296702-lsp0crpm-clk";
reg = <0x0b000000 0x1000>;
#clock-cells = <1>;
};
- uart0: serial@0x09405000 {
+ uart0: serial@9405000 {
compatible = "zte,zx296702-uart";
reg = <0x09405000 0x1000>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
@@ -98,7 +98,7 @@
status = "disabled";
};
- uart1: serial@0x09406000 {
+ uart1: serial@9406000 {
compatible = "zte,zx296702-uart";
reg = <0x09406000 0x1000>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
@@ -106,7 +106,7 @@
status = "disabled";
};
- mmc0: mmc@0x09408000 {
+ mmc0: mmc@9408000 {
compatible = "snps,dw-mshc";
#address-cells = <1>;
#size-cells = <0>;
@@ -119,7 +119,7 @@
status = "disabled";
};
- mmc1: mmc@0x0b003000 {
+ mmc1: mmc@b003000 {
compatible = "snps,dw-mshc";
#address-cells = <1>;
#size-cells = <0>;
@@ -132,7 +132,7 @@
status = "disabled";
};
- sysctrl: sysctrl@0xa0007000 {
+ sysctrl: sysctrl@a0007000 {
compatible = "zte,sysctrl", "syscon";
reg = <0xa0007000 0x1000>;
};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH] arc: dts: Remove leading 0x and 0s from bindings notation
From: Mathieu Malaterre @ 2017-12-14 16:53 UTC (permalink / raw)
To: Rob Herring
Cc: Mathieu Malaterre, Mark Rutland, Vineet Gupta, Alexey Brodkin,
devicetree, linux-snps-arc, linux-kernel
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
---
arch/arc/boot/dts/abilis_tb10x.dtsi | 4 ++--
arch/arc/boot/dts/axc001.dtsi | 6 +++---
arch/arc/boot/dts/axc003.dtsi | 6 +++---
arch/arc/boot/dts/axc003_idu.dtsi | 6 +++---
arch/arc/boot/dts/axs10x_mb.dtsi | 22 +++++++++++-----------
arch/arc/boot/dts/vdk_axc003.dtsi | 4 ++--
arch/arc/boot/dts/vdk_axc003_idu.dtsi | 4 ++--
arch/arc/boot/dts/vdk_axs10x_mb.dtsi | 14 +++++++-------
8 files changed, 33 insertions(+), 33 deletions(-)
diff --git a/arch/arc/boot/dts/abilis_tb10x.dtsi b/arch/arc/boot/dts/abilis_tb10x.dtsi
index 3121536b25a3..593cdd96535d 100644
--- a/arch/arc/boot/dts/abilis_tb10x.dtsi
+++ b/arch/arc/boot/dts/abilis_tb10x.dtsi
@@ -178,7 +178,7 @@
clocks = <&ahb_clk>;
};
- spi0: spi@0xFE010000 {
+ spi0: spi@fe010000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
@@ -189,7 +189,7 @@
interrupts = <26 8>;
clocks = <&ahb_clk>;
};
- spi1: spi@0xFE011000 {
+ spi1: spi@fe011000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <1>;
diff --git a/arch/arc/boot/dts/axc001.dtsi b/arch/arc/boot/dts/axc001.dtsi
index fdc266504ada..37be3bf03ad6 100644
--- a/arch/arc/boot/dts/axc001.dtsi
+++ b/arch/arc/boot/dts/axc001.dtsi
@@ -41,7 +41,7 @@
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
- dw-apb-gpio@0x2000 {
+ dw-apb-gpio@2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
@@ -60,7 +60,7 @@
};
};
- debug_uart: dw-apb-uart@0x5000 {
+ debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
@@ -88,7 +88,7 @@
* avoid duplicating the MB dtsi file given that IRQ from
* this intc to cpu intc are different for axs101 and axs103
*/
- mb_intc: dw-apb-ictl@0xe0012000 {
+ mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x0 0xe0012000 0x0 0x200 >;
diff --git a/arch/arc/boot/dts/axc003.dtsi b/arch/arc/boot/dts/axc003.dtsi
index 4e6e9f57e790..f33694d08e1f 100644
--- a/arch/arc/boot/dts/axc003.dtsi
+++ b/arch/arc/boot/dts/axc003.dtsi
@@ -47,7 +47,7 @@
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
- dw-apb-gpio@0x2000 {
+ dw-apb-gpio@2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
@@ -66,7 +66,7 @@
};
};
- debug_uart: dw-apb-uart@0x5000 {
+ debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
@@ -98,7 +98,7 @@
* avoid duplicating the MB dtsi file given that IRQ from
* this intc to cpu intc are different for axs101 and axs103
*/
- mb_intc: dw-apb-ictl@0xe0012000 {
+ mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x0 0xe0012000 0x0 0x200 >;
diff --git a/arch/arc/boot/dts/axc003_idu.dtsi b/arch/arc/boot/dts/axc003_idu.dtsi
index 63954a8b0100..256790bbd4a0 100644
--- a/arch/arc/boot/dts/axc003_idu.dtsi
+++ b/arch/arc/boot/dts/axc003_idu.dtsi
@@ -54,7 +54,7 @@
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
- dw-apb-gpio@0x2000 {
+ dw-apb-gpio@2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
@@ -73,7 +73,7 @@
};
};
- debug_uart: dw-apb-uart@0x5000 {
+ debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
@@ -104,7 +104,7 @@
* avoid duplicating the MB dtsi file given that IRQ from
* this intc to cpu intc are different for axs101 and axs103
*/
- mb_intc: dw-apb-ictl@0xe0012000 {
+ mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x0 0xe0012000 0x0 0x200 >;
diff --git a/arch/arc/boot/dts/axs10x_mb.dtsi b/arch/arc/boot/dts/axs10x_mb.dtsi
index 74d070cd3c13..e4c64c05e32f 100644
--- a/arch/arc/boot/dts/axs10x_mb.dtsi
+++ b/arch/arc/boot/dts/axs10x_mb.dtsi
@@ -68,7 +68,7 @@
};
};
- ethernet@0x18000 {
+ ethernet@18000 {
#interrupt-cells = <1>;
compatible = "snps,dwmac";
reg = < 0x18000 0x2000 >;
@@ -83,13 +83,13 @@
reset-names = "stmmaceth";
};
- ehci@0x40000 {
+ ehci@40000 {
compatible = "generic-ehci";
reg = < 0x40000 0x100 >;
interrupts = < 8 >;
};
- ohci@0x60000 {
+ ohci@60000 {
compatible = "generic-ohci";
reg = < 0x60000 0x100 >;
interrupts = < 8 >;
@@ -113,7 +113,7 @@
* dw_mci_pltfm_prepare_command() is used in generic platform
* code.
*/
- mmc@0x15000 {
+ mmc@15000 {
compatible = "altr,socfpga-dw-mshc";
reg = < 0x15000 0x400 >;
fifo-depth = < 16 >;
@@ -124,7 +124,7 @@
bus-width = < 4 >;
};
- uart@0x20000 {
+ uart@20000 {
compatible = "snps,dw-apb-uart";
reg = <0x20000 0x100>;
clock-frequency = <33333333>;
@@ -134,7 +134,7 @@
reg-io-width = <4>;
};
- uart@0x21000 {
+ uart@21000 {
compatible = "snps,dw-apb-uart";
reg = <0x21000 0x100>;
clock-frequency = <33333333>;
@@ -145,7 +145,7 @@
};
/* UART muxed with USB data port (ttyS3) */
- uart@0x22000 {
+ uart@22000 {
compatible = "snps,dw-apb-uart";
reg = <0x22000 0x100>;
clock-frequency = <33333333>;
@@ -155,7 +155,7 @@
reg-io-width = <4>;
};
- i2c@0x1d000 {
+ i2c@1d000 {
compatible = "snps,designware-i2c";
reg = <0x1d000 0x100>;
clock-frequency = <400000>;
@@ -172,7 +172,7 @@
#sound-dai-cells = <0>;
};
- i2c@0x1f000 {
+ i2c@1f000 {
compatible = "snps,designware-i2c";
#address-cells = <1>;
#size-cells = <0>;
@@ -213,13 +213,13 @@
};
};
- eeprom@0x54{
+ eeprom@54 {
compatible = "24c01";
reg = <0x54>;
pagesize = <0x8>;
};
- eeprom@0x57{
+ eeprom@57 {
compatible = "24c04";
reg = <0x57>;
pagesize = <0x8>;
diff --git a/arch/arc/boot/dts/vdk_axc003.dtsi b/arch/arc/boot/dts/vdk_axc003.dtsi
index 0fd6ba985b16..84e8766c8ca2 100644
--- a/arch/arc/boot/dts/vdk_axc003.dtsi
+++ b/arch/arc/boot/dts/vdk_axc003.dtsi
@@ -36,7 +36,7 @@
#interrupt-cells = <1>;
};
- debug_uart: dw-apb-uart@0x5000 {
+ debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <2403200>;
@@ -49,7 +49,7 @@
};
- mb_intc: dw-apb-ictl@0xe0012000 {
+ mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0xe0012000 0x200 >;
diff --git a/arch/arc/boot/dts/vdk_axc003_idu.dtsi b/arch/arc/boot/dts/vdk_axc003_idu.dtsi
index 28956f9a9f3d..eb7e705e8a27 100644
--- a/arch/arc/boot/dts/vdk_axc003_idu.dtsi
+++ b/arch/arc/boot/dts/vdk_axc003_idu.dtsi
@@ -44,7 +44,7 @@
#interrupt-cells = <1>;
};
- debug_uart: dw-apb-uart@0x5000 {
+ debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <2403200>;
@@ -57,7 +57,7 @@
};
- mb_intc: dw-apb-ictl@0xe0012000 {
+ mb_intc: dw-apb-ictl@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0xe0012000 0x200 >;
diff --git a/arch/arc/boot/dts/vdk_axs10x_mb.dtsi b/arch/arc/boot/dts/vdk_axs10x_mb.dtsi
index 48bb4b4cd234..f21ade2931eb 100644
--- a/arch/arc/boot/dts/vdk_axs10x_mb.dtsi
+++ b/arch/arc/boot/dts/vdk_axs10x_mb.dtsi
@@ -36,7 +36,7 @@
};
};
- ethernet@0x18000 {
+ ethernet@18000 {
#interrupt-cells = <1>;
compatible = "snps,dwmac";
reg = < 0x18000 0x2000 >;
@@ -49,13 +49,13 @@
clock-names = "stmmaceth";
};
- ehci@0x40000 {
+ ehci@40000 {
compatible = "generic-ehci";
reg = < 0x40000 0x100 >;
interrupts = < 8 >;
};
- uart@0x20000 {
+ uart@20000 {
compatible = "snps,dw-apb-uart";
reg = <0x20000 0x100>;
clock-frequency = <2403200>;
@@ -65,7 +65,7 @@
reg-io-width = <4>;
};
- uart@0x21000 {
+ uart@21000 {
compatible = "snps,dw-apb-uart";
reg = <0x21000 0x100>;
clock-frequency = <2403200>;
@@ -75,7 +75,7 @@
reg-io-width = <4>;
};
- uart@0x22000 {
+ uart@22000 {
compatible = "snps,dw-apb-uart";
reg = <0x22000 0x100>;
clock-frequency = <2403200>;
@@ -101,7 +101,7 @@
interrupt-names = "arc_ps2_irq";
};
- mmc@0x15000 {
+ mmc@15000 {
compatible = "snps,dw-mshc";
reg = <0x15000 0x400>;
fifo-depth = <1024>;
@@ -119,7 +119,7 @@
* This node is intentionally put outside of MB above becase
* it maps areas outside of MB's 0xEz-0xFz.
*/
- uio_ev: uio@0xD0000000 {
+ uio_ev: uio@d0000000 {
compatible = "generic-uio";
reg = <0xD0000000 0x2000 0xD1000000 0x2000 0x90000000 0x10000000 0xC0000000 0x10000000>;
reg-names = "ev_gsa", "ev_ctrl", "ev_shared_mem", "ev_code_mem";
--
2.11.0
^ permalink raw reply related
* Re: [PATCH v7 6/6] arm64: dts: meson-axg: switch uart_ao clock to CLK81
From: Jerome Brunet @ 2017-12-14 16:47 UTC (permalink / raw)
To: Yixun Lan, Neil Armstrong, Kevin Hilman
Cc: Rob Herring, Mark Rutland, Michael Turquette, Stephen Boyd,
Carlo Caione, Qiufang Dai, Jian Hu, linux-amlogic, devicetree,
linux-clk, linux-arm-kernel, linux-kernel
In-Reply-To: <20171211141348.22048-7-yixun.lan@amlogic.com>
On Mon, 2017-12-11 at 22:13 +0800, Yixun Lan wrote:
> Switch the uart_ao pclk to CLK81 since the clock driver is ready.
> Also move the clock info to the board.dts instead in the soc.dtsi.
Same comment as for ethmac, is it really wise ?
Isn't the clock setup the same for the axg family ?
>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
^ permalink raw reply
* Re: [PATCH v2] ARM64: dts: meson-axg: add ethernet mac controller
From: Jerome Brunet @ 2017-12-14 16:45 UTC (permalink / raw)
To: Yixun Lan, devicetree, Kevin Hilman
Cc: Neil Armstrong, Giuseppe Cavallaro, Alexandre Torgue,
Carlo Caione, linux-amlogic, linux-arm-kernel, linux-kernel,
netdev
In-Reply-To: <20171214030242.113152-1-yixun.lan@amlogic.com>
On Thu, 2017-12-14 at 11:02 +0800, Yixun Lan wrote:
> ---
> Changes in v2 since [1]:
> - rebase to kevin's v4.16/dt64 branch
> - add Neil's Reviewed-by
> - move clock info to board.dts instead of in soc.dtsi
You got this comment regarding the pwm clock setup. the setup of the pwm clocks
depends on the use case, so should defined depending on the requirement on the
board
This is not the case for the ethmac, the clock setup will be same for every
board, unless I missed something. the clock bindings should be defined in
meson-axg.dtsi, I think
> - drop "meson-axg-dwmac" compatible string, since we didn't use this
> we could re-add it later when we really need.
> - note: to make ethernet work properly,it depend on clock & pinctrl[2],
> to compile the DTS, the patch [3] is required.
> the code part will be taken via clock & pinctrl subsystem tree.
^ permalink raw reply
* Re: [PATCH 4/4] PM / OPP: Add ti-opp-supply driver
From: Dave Gerlach @ 2017-12-14 16:31 UTC (permalink / raw)
To: Viresh Kumar
Cc: Rob Herring, Rafael J . Wysocki, linux-arm-kernel, linux-omap,
linux-pm, devicetree, Tony Lindgren, Nishanth Menon
In-Reply-To: <20171214043432.GT3322@vireshk-i7>
Hi,
On 12/13/2017 10:34 PM, Viresh Kumar wrote:
> On 13-12-17, 14:33, Dave Gerlach wrote:
>> Introduce a ti-opp-supply driver that will use new multiple regulator
>> support that is part of the OPP core This is needed on TI platforms like
>> DRA7/AM57 in order to control both CPU regulator and Adaptive Body Bias
>> (ABB) regulator. These regulators must be scaled in sequence during an
>> OPP transition depending on whether or not the frequency is being scaled
>> up or down.
>>
>> This driver also implements AVS Class0 for these parts by looking up the
>> required values from registers in the SoC and programming adjusted
>> optimal voltage values for each OPP.
>>
>> Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
>> ---
>> drivers/opp/Makefile | 1 +
>> drivers/opp/ti-opp-supply.c | 428 ++++++++++++++++++++++++++++++++++++++++++++
>
> Why is this added as a separate driver and not part of the same ti-cpufreq.c
> file?
>
Although we are only currently using this for cpufreq, in the future it can be
used for the other voltage domains that are unrelated to the CPU that support
AVS Class0. Table 5-7 in http://www.ti.com/lit/ds/symlink/am5728.pdf shows the
support for each voltage domain.
>> 2 files changed, 429 insertions(+)
>> create mode 100644 drivers/opp/ti-opp-supply.c
>>
>> diff --git a/drivers/opp/Makefile b/drivers/opp/Makefile
>> index e70ceb406fe9..6ce6aefacc81 100644
>> --- a/drivers/opp/Makefile
>> +++ b/drivers/opp/Makefile
>> @@ -2,3 +2,4 @@ ccflags-$(CONFIG_DEBUG_DRIVER) := -DDEBUG
>> obj-y += core.o cpu.o
>> obj-$(CONFIG_OF) += of.o
>> obj-$(CONFIG_DEBUG_FS) += debugfs.o
>> +obj-$(CONFIG_ARM_TI_CPUFREQ) += ti-opp-supply.o
>> diff --git a/drivers/opp/ti-opp-supply.c b/drivers/opp/ti-opp-supply.c
>> new file mode 100644
>> index 000000000000..73d795c90b79
>> --- /dev/null
>> +++ b/drivers/opp/ti-opp-supply.c
>> @@ -0,0 +1,428 @@
>> +/*
>> + * Copyright (C) 2016-2017 Texas Instruments Incorporated - http://www.ti.com/
>> + * Nishanth Menon <nm@ti.com>
>> + * Dave Gerlach <d-gerlach@ti.com>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>
> Please use the new SPDX format for licenses.
Ah ok, will do.
>
>> + * TI OPP supply driver that provides override into the regulator control
>> + * for generic opp core to handle devices with ABB regulator and/or
>> + * SmartReflex Class0.
>> + */
>> +#include <linux/clk.h>
>> +#include <linux/cpufreq.h>
>> +#include <linux/device.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/notifier.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/pm_opp.h>
>> +#include <linux/regulator/consumer.h>
>> +#include <linux/slab.h>
>> +
>> +/**
>> + * struct ti_opp_supply_optimum_voltage_table - optimized voltage table
>> + * @reference_uv: reference voltage (usually Nominal voltage)
>> + * @optimized_uv: Optimized voltage from efuse
>> + */
>> +struct ti_opp_supply_optimum_voltage_table {
>> + unsigned int reference_uv;
>> + unsigned int optimized_uv;
>> +};
>> +
>> +/**
>> + * struct ti_opp_supply_data - OMAP specific opp supply data
>> + * @vdd_table: Optimized voltage mapping table
>> + * @num_vdd_table: number of entries in vdd_table
>> + * @vdd_absolute_max_voltage_uv: absolute maximum voltage in UV for the supply
>> + */
>> +struct ti_opp_supply_data {
>> + struct ti_opp_supply_optimum_voltage_table *vdd_table;
>> + u32 num_vdd_table;
>> + u32 vdd_absolute_max_voltage_uv;
>> +};
>> +
>> +static struct ti_opp_supply_data opp_data;
>> +
>> +/**
>> + * struct ti_opp_supply_of_data - device tree match data
>> + * @flags: specific type of opp supply
>> + * @efuse_voltage_mask: mask required for efuse register representing voltage
>> + * @efuse_voltage_uv: Are the efuse entries in micro-volts? if not, assume
>> + * milli-volts.
>> + */
>> +struct ti_opp_supply_of_data {
>> +#define OPPDM_EFUSE_CLASS0_OPTIMIZED_VOLTAGE BIT(1)
>> +#define OPPDM_HAS_NO_ABB BIT(2)
>> + const u8 flags;
>> + const u32 efuse_voltage_mask;
>> + const bool efuse_voltage_uv;
>> +};
>> +
>> +/**
>> + * _store_optimized_voltages() - store optimized voltages
>> + * @dev: ti opp supply device for which we need to store info
>> + * @data: data specific to the device
>> + *
>> + * Picks up efuse based optimized voltages for VDD unique per device and
>> + * stores it in internal data structure for use during transition requests.
>> + *
>> + * Return: If successful, 0, else appropriate error value.
>> + */
>> +static int _store_optimized_voltages(struct device *dev,
>> + struct ti_opp_supply_data *data)
>> +{
>> + void __iomem *base;
>> + struct property *prop;
>> + struct resource *res;
>> + const __be32 *val;
>> + int proplen, i;
>> + int ret = 0;
>> + struct ti_opp_supply_optimum_voltage_table *table;
>> + const struct ti_opp_supply_of_data *of_data = dev_get_drvdata(dev);
>> +
>> + /* pick up Efuse based voltages */
>> + res = platform_get_resource(to_platform_device(dev), IORESOURCE_MEM, 0);
>> + if (!res) {
>> + dev_err(dev, "Unable to get IO resource\n");
>> + ret = -ENODEV;
>> + goto out_map;
>> + }
>> +
>> + base = ioremap_nocache(res->start, resource_size(res));
>> + if (!base) {
>> + dev_err(dev, "Unable to map Efuse registers\n");
>> + ret = -ENOMEM;
>> + goto out_map;
>> + }
>> +
>> + /* Fetch efuse-settings. */
>> + prop = of_find_property(dev->of_node, "ti,efuse-settings", NULL);
>> + if (!prop) {
>> + dev_err(dev, "No 'ti,efuse-settings' property found\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + proplen = prop->length / sizeof(int);
>> + data->num_vdd_table = proplen / 2;
>> + /* Verify for corrupted OPP entries in dt */
>> + if (data->num_vdd_table * 2 * sizeof(int) != prop->length) {
>> + dev_err(dev, "Invalid 'ti,efuse-settings'\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + ret = of_property_read_u32(dev->of_node, "ti,absolute-max-voltage-uv",
>> + &data->vdd_absolute_max_voltage_uv);
>> + if (ret) {
>> + dev_err(dev, "ti,absolute-max-voltage-uv is missing\n");
>> + ret = -EINVAL;
>> + goto out;
>> + }
>> +
>> + table = kzalloc(sizeof(*data->vdd_table) *
>> + data->num_vdd_table, GFP_KERNEL);
>> + if (!table) {
>> + ret = -ENOMEM;
>> + goto out;
>> + }
>> + data->vdd_table = table;
>> +
>> + val = prop->value;
>> + for (i = 0; i < data->num_vdd_table; i++, table++) {
>> + u32 efuse_offset;
>> + u32 tmp;
>> +
>> + table->reference_uv = be32_to_cpup(val++);
>> + efuse_offset = be32_to_cpup(val++);
>> +
>> + tmp = readl(base + efuse_offset);
>> + tmp &= of_data->efuse_voltage_mask;
>> + tmp >>= __ffs(of_data->efuse_voltage_mask);
>> +
>> + table->optimized_uv = of_data->efuse_voltage_uv ? tmp :
>> + tmp * 1000;
>> +
>> + dev_dbg(dev, "[%d] efuse=0x%08x volt_table=%d vset=%d\n",
>> + i, efuse_offset, table->reference_uv,
>> + table->optimized_uv);
>> +
>> + /*
>> + * Some older samples might not have optimized efuse
>> + * Use reference voltage for those - just add debug message
>> + * for them.
>> + */
>> + if (!table->optimized_uv) {
>> + dev_dbg(dev, "[%d] efuse=0x%08x volt_table=%d:vset0\n",
>> + i, efuse_offset, table->reference_uv);
>> + table->optimized_uv = table->reference_uv;
>> + }
>> + }
>> +out:
>> + iounmap(base);
>> +out_map:
>> + return ret;
>> +}
>> +
>> +/**
>> + * _free_optimized_voltages() - free resources for optvoltages
>> + * @dev: device for which we need to free info
>> + * @data: data specific to the device
>> + */
>> +static void _free_optimized_voltages(struct device *dev,
>> + struct ti_opp_supply_data *data)
>> +{
>> + kfree(data->vdd_table);
>> + data->vdd_table = NULL;
>> + data->num_vdd_table = 0;
>> +}
>> +
>> +/**
>> + * _get_optimal_vdd_voltage() - Finds optimal voltage for the supply
>> + * @dev: device for which we need to find info
>> + * @data: data specific to the device
>> + * @reference_uv: reference voltage (OPP voltage) for which we need value
>> + *
>> + * Return: if a match is found, return optimized voltage, else return
>> + * reference_uv, also return reference_uv if no optimization is needed.
>> + */
>> +static int _get_optimal_vdd_voltage(struct device *dev,
>> + struct ti_opp_supply_data *data,
>> + int reference_uv)
>> +{
>> + int i;
>> + struct ti_opp_supply_optimum_voltage_table *table;
>> +
>> + if (!data->num_vdd_table)
>> + return reference_uv;
>> +
>> + table = data->vdd_table;
>> + if (!table)
>> + return -EINVAL;
>> +
>> + /* Find a exact match - this list is usually very small */
>> + for (i = 0; i < data->num_vdd_table; i++, table++)
>> + if (table->reference_uv == reference_uv)
>> + return table->optimized_uv;
>> +
>> + /* IF things are screwed up, we'd make a mess on console.. ratelimit */
>> + dev_err_ratelimited(dev, "%s: Failed optimized voltage match for %d\n",
>> + __func__, reference_uv);
>> + return reference_uv;
>> +}
>> +
>> +static int _opp_set_voltage(struct device *dev,
>> + struct dev_pm_opp_supply *supply,
>> + int new_target_uv, struct regulator *reg,
>> + char *reg_name)
>> +{
>> + int ret;
>> + unsigned long vdd_uv, uv_max;
>> +
>> + if (new_target_uv)
>> + vdd_uv = new_target_uv;
>> + else
>> + vdd_uv = supply->u_volt;
>> +
>> + /*
>> + * If we do have an absolute max voltage specified, then we should
>> + * use that voltage instead to allow for cases where the voltage rails
>> + * are ganged (example if we set the max for an opp as 1.12v, and
>> + * the absolute max is 1.5v, for another rail to get 1.25v, it cannot
>> + * be achieved if the regulator is constrainted to max of 1.12v, even
>> + * if it can function at 1.25v
>> + */
>> + if (opp_data.vdd_absolute_max_voltage_uv)
>> + uv_max = opp_data.vdd_absolute_max_voltage_uv;
>> + else
>> + uv_max = supply->u_volt_max;
>> +
>> + if (vdd_uv > uv_max ||
>> + vdd_uv < supply->u_volt_min ||
>> + supply->u_volt_min > uv_max) {
>> + dev_warn(dev,
>> + "Invalid range voltages [Min:%lu target:%lu Max:%lu]\n",
>> + supply->u_volt_min, vdd_uv, uv_max);
>> + return -EINVAL;
>> + }
>> +
>> + dev_dbg(dev, "%s scaling to %luuV[min %luuV max %luuV]\n", reg_name,
>> + vdd_uv, supply->u_volt_min,
>> + uv_max);
>> +
>> + ret = regulator_set_voltage_triplet(reg,
>> + supply->u_volt_min,
>> + vdd_uv,
>> + uv_max);
>> + if (ret) {
>> + dev_err(dev, "%s failed for %luuV[min %luuV max %luuV]\n",
>> + reg_name, vdd_uv, supply->u_volt_min,
>> + uv_max);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +/**
>> + * ti_opp_supply_set_opp() - do the opp supply transition
>> + * @data: information on regulators and new and old opps provided by
>> + * opp core to use in transition
>> + *
>> + * Return: If successful, 0, else appropriate error value.
>> + */
>> +int ti_opp_supply_set_opp(struct dev_pm_set_opp_data *data)
>> +{
>> + struct dev_pm_opp_supply *old_supply_vdd = &data->old_opp.supplies[0];
>> + struct dev_pm_opp_supply *old_supply_vbb = &data->old_opp.supplies[1];
>> + struct dev_pm_opp_supply *new_supply_vdd = &data->new_opp.supplies[0];
>> + struct dev_pm_opp_supply *new_supply_vbb = &data->new_opp.supplies[1];
>> + struct device *dev = data->dev;
>> + unsigned long old_freq = data->old_opp.rate, freq = data->new_opp.rate;
>> + struct clk *clk = data->clk;
>> + struct regulator *vdd_reg = data->regulators[0];
>> + struct regulator *vbb_reg = data->regulators[1];
>> + int vdd_uv;
>> + int ret;
>> +
>> + vdd_uv = _get_optimal_vdd_voltage(dev, &opp_data,
>> + new_supply_vbb->u_volt);
>> +
>> + /* Scaling up? Scale voltage before frequency */
>> + if (freq > old_freq) {
>> + ret = _opp_set_voltage(dev, new_supply_vdd, vdd_uv, vdd_reg,
>> + "vdd");
>> + if (ret)
>> + goto restore_voltage;
>> +
>> + ret = _opp_set_voltage(dev, new_supply_vbb, 0, vbb_reg, "vbb");
>> + if (ret)
>> + goto restore_voltage;
>> + }
>> +
>> + /* Change frequency */
>> + dev_dbg(dev, "%s: switching OPP: %lu Hz --> %lu Hz\n",
>> + __func__, old_freq, freq);
>> +
>> + ret = clk_set_rate(clk, freq);
>> + if (ret) {
>> + dev_err(dev, "%s: failed to set clock rate: %d\n", __func__,
>> + ret);
>> + goto restore_voltage;
>> + }
>> +
>> + /* Scaling down? Scale voltage after frequency */
>> + if (freq < old_freq) {
>> + ret = _opp_set_voltage(dev, new_supply_vbb, 0, vbb_reg, "vbb");
>> + if (ret)
>> + goto restore_freq;
>> +
>> + ret = _opp_set_voltage(dev, new_supply_vdd, vdd_uv, vdd_reg,
>> + "vdd");
>> + if (ret)
>> + goto restore_freq;
>> + }
>> +
>> + return 0;
>> +
>> +restore_freq:
>> + ret = clk_set_rate(clk, old_freq);
>> + if (ret)
>> + dev_err(dev, "%s: failed to restore old-freq (%lu Hz)\n",
>> + __func__, old_freq);
>> +restore_voltage:
>> + /* This shouldn't harm even if the voltages weren't updated earlier */
>> + if (old_supply_vdd->u_volt) {
>> + ret = _opp_set_voltage(dev, old_supply_vbb, 0, vbb_reg, "vbb");
>> + if (ret)
>> + return ret;
>> +
>> + ret = _opp_set_voltage(dev, old_supply_vdd, 0, vdd_reg,
>> + "vdd");
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +static const struct ti_opp_supply_of_data omap_generic_of_data = {
>> +};
>> +
>> +static const struct ti_opp_supply_of_data omap_omap5_of_data = {
>> + .flags = OPPDM_EFUSE_CLASS0_OPTIMIZED_VOLTAGE,
>> + .efuse_voltage_mask = 0xFFF,
>> + .efuse_voltage_uv = false,
>> +};
>> +
>> +static const struct ti_opp_supply_of_data omap_omap5core_of_data = {
>> + .flags = OPPDM_EFUSE_CLASS0_OPTIMIZED_VOLTAGE | OPPDM_HAS_NO_ABB,
>> + .efuse_voltage_mask = 0xFFF,
>> + .efuse_voltage_uv = false,
>> +};
>> +
>> +static const struct of_device_id ti_opp_supply_of_match[] = {
>> + {.compatible = "ti,omap-opp-supply", .data = &omap_generic_of_data},
>> + {.compatible = "ti,omap5-opp-supply", .data = &omap_omap5_of_data},
>> + {.compatible = "ti,omap5-core-opp-supply",
>> + .data = &omap_omap5core_of_data},
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(of, ti_opp_supply_of_match);
>> +
>> +static int ti_opp_supply_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device *cpu_dev = get_cpu_device(0);
>> + const struct of_device_id *match;
>> + const struct ti_opp_supply_of_data *of_data;
>> + int ret = 0;
>> +
>> + match = of_match_device(ti_opp_supply_of_match, dev);
>> + if (!match) {
>> + /* We do not expect this to happen */
>> + dev_err(dev, "%s: Unable to match device\n", __func__);
>> + return -ENODEV;
>> + }
>> + if (!match->data) {
>> + /* Again, unlikely.. but mistakes do happen */
>> + dev_err(dev, "%s: Bad data in match\n", __func__);
>> + return -EINVAL;
>> + }
>> + of_data = match->data;
>> +
>> + dev_set_drvdata(dev, (void *)of_data);
>> +
>> + /* If we need optimized voltage */
>> + if (of_data->flags & OPPDM_EFUSE_CLASS0_OPTIMIZED_VOLTAGE) {
>> + ret = _store_optimized_voltages(dev, &opp_data);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + ret = PTR_ERR_OR_ZERO(dev_pm_opp_register_set_opp_helper(cpu_dev,
>> + ti_opp_supply_set_opp));
>> + if (ret)
>> + _free_optimized_voltages(dev, &opp_data);
>> +
>> + return ret;
>> +}
>> +
>> +static struct platform_driver ti_opp_supply_driver = {
>> + .probe = ti_opp_supply_probe,
>> + .driver = {
>> + .name = "ti_opp_supply",
>> + .owner = THIS_MODULE,
>> + .of_match_table = of_match_ptr(ti_opp_supply_of_match),
>> + },
>> +};
>> +module_platform_driver(ti_opp_supply_driver);
>> +
>> +MODULE_DESCRIPTION("Texas Instruments OMAP OPP Supply driver");
>> +MODULE_AUTHOR("Texas Instruments Inc.");
>> +MODULE_LICENSE("GPL v2");
>
> Looks fine otherwise.
>
Thanks, appreciate the review, will resend with fixed license.
Regards,
Dave
^ permalink raw reply
* [patch v14 4/4] Documentation: jtag: Add ABI documentation
From: Oleksandr Shamray @ 2017-12-14 16:29 UTC (permalink / raw)
To: gregkh, arnd
Cc: linux-kernel, linux-arm-kernel, devicetree, openbmc, joel, jiri,
tklauser, linux-serial, vadimp, system-sw-low-level, robh+dt,
openocd-devel-owner, linux-api, davem, mchehab, Oleksandr Shamray
In-Reply-To: <1513268971-13518-1-git-send-email-oleksandrs@mellanox.com>
Added document that describe the ABI for JTAG class drivrer
Signed-off-by: Oleksandr Shamray <oleksandrs@mellanox.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
---
v13->v14
v12->v13
v11->v12
Tobias Klauser <tklauser@distanz.ch>
- rename /Documentation/ABI/testing/jatg-dev -> jtag-dev
- Typo: s/interfase/interface
v10->v11
v9->v10
Fixes added by Oleksandr:
- change jtag-cdev to jtag-dev in documentation
- update Kernel Version and Date in jtag-dev documentation;
v8->v9
v7->v8
v6->v7
Comments pointed by Pavel Machek <pavel@ucw.cz>
- Added jtag-cdev documentation to Documentation/ABI/testing folder
---
Documentation/ABI/testing/jtag-dev | 27 +++++++++++++++++++++++++++
1 files changed, 27 insertions(+), 0 deletions(-)
create mode 100644 Documentation/ABI/testing/jtag-dev
diff --git a/Documentation/ABI/testing/jtag-dev b/Documentation/ABI/testing/jtag-dev
new file mode 100644
index 0000000..cab867d
--- /dev/null
+++ b/Documentation/ABI/testing/jtag-dev
@@ -0,0 +1,27 @@
+What: /dev/jtag[0-9]+
+Date: October 2017
+KernelVersion: 4.15
+Contact: oleksandrs@mellanox.com
+Description:
+ The misc device files /dev/jtag* are the interface
+ between JTAG master interface and userspace.
+
+ The ioctl(2)-based ABI is defined and documented in
+ [include/uapi]<linux/jtag.h>.
+
+ The following file operations are supported:
+
+ open(2)
+ The argument flag currently support only one access
+ mode O_RDWR.
+
+ ioctl(2)
+ Initiate various actions.
+ See the inline documentation in [include/uapi]<linux/jtag.h>
+ for descriptions of all ioctls.
+
+ close(2)
+ Stops and free up the I/O contexts that was associated
+ with the file descriptor.
+
+Users: TBD
\ No newline at end of file
--
1.7.1
^ permalink raw reply related
* [patch v14 3/4] Documentation: jtag: Add bindings for Aspeed SoC 24xx and 25xx families JTAG master driver
From: Oleksandr Shamray @ 2017-12-14 16:29 UTC (permalink / raw)
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, arnd-r2nGTMty4D4
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ,
joel-U3u1mxZcP9KHXe+LvDLADg, jiri-rHqAuBHg3fBzbRFIqnYvSA,
tklauser-93Khv+1bN0NyDzI6CaY1VQ,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
vadimp-VPRAkNaXOzVWk0Htik3J/w,
system-sw-low-level-VPRAkNaXOzVWk0Htik3J/w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
openocd-devel-owner-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f,
linux-api-u79uwXL29TY76Z2rM5mHXA, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, Oleksandr Shamray, Jiri Pirko
In-Reply-To: <1513268971-13518-1-git-send-email-oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
It has been tested on Mellanox system with BMC equipped with
Aspeed 2520 SoC for programming CPLD devices.
Signed-off-by: Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Signed-off-by: Jiri Pirko <jiri-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
v13->v14
v12->v13
v11->v12
v10->v11
v9->v10
v8->v9
v7->v8
Comments pointed by pointed by Joel Stanley <joel.stan-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
- Change compatible string to ast2400 and ast2000
V6->v7
Comments pointed by Tobias Klauser <tklauser-93Khv+1bN0NyDzI6CaY1VQ@public.gmane.org>
- Fix spell "Doccumentation" -> "Documentation"
v5->v6
Comments pointed by Tobias Klauser <tklauser-93Khv+1bN0NyDzI6CaY1VQ@public.gmane.org>
- Small nit: s/documentation/Documentation/
v4->v5
V3->v4
Comments pointed by Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
- delete unnecessary "status" and "reg-shift" descriptions in
bndings file
v2->v3
Comments pointed by Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
- split Aspeed jtag driver and binding to sepatrate patches
- delete unnecessary "status" and "reg-shift" descriptions in
bndings file
---
.../devicetree/bindings/jtag/aspeed-jtag.txt | 18 ++++++++++++++++++
1 files changed, 18 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
diff --git a/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
new file mode 100644
index 0000000..8cfc610
--- /dev/null
+++ b/Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
@@ -0,0 +1,18 @@
+Aspeed JTAG driver for ast2400 and ast2500 SoC
+
+Required properties:
+- compatible: Should be one of
+ - "aspeed,ast2400-jtag"
+ - "aspeed,ast2500-jtag"
+- reg contains the offset and length of the JTAG memory
+ region
+- clocks root clock of bus, should reference the APB clock
+- interrupts should contain JTAG controller interrupt
+
+Example:
+jtag: jtag@1e6e4000 {
+ compatible = "aspeed,ast2500-jtag";
+ reg = <0x1e6e4000 0x1c>;
+ clocks = <&clk_apb>;
+ interrupts = <43>;
+};
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [patch v14 2/4] drivers: jtag: Add Aspeed SoC 24xx and 25xx families JTAG master driver
From: Oleksandr Shamray @ 2017-12-14 16:29 UTC (permalink / raw)
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, arnd-r2nGTMty4D4
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ,
joel-U3u1mxZcP9KHXe+LvDLADg, jiri-rHqAuBHg3fBzbRFIqnYvSA,
tklauser-93Khv+1bN0NyDzI6CaY1VQ,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
vadimp-VPRAkNaXOzVWk0Htik3J/w,
system-sw-low-level-VPRAkNaXOzVWk0Htik3J/w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
openocd-devel-owner-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f,
linux-api-u79uwXL29TY76Z2rM5mHXA, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, Oleksandr Shamray, Jiri Pirko
In-Reply-To: <1513268971-13518-1-git-send-email-oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Driver adds support of Aspeed 2500/2400 series SOC JTAG master controller.
Driver implements the following jtag ops:
- freq_get;
- freq_set;
- status_get;
- idle;
- xfer;
It has been tested on Mellanox system with BMC equipped with
Aspeed 2520 SoC for programming CPLD devices.
Signed-off-by: Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Signed-off-by: Jiri Pirko <jiri-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Acked-by: Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
---
v13->v14
Comments pointed by Philippe Ombredanne <pombredanne-od1rfyK75/E@public.gmane.org>
- Change style of head block comment from /**/ to //
v12->v13
Comments pointed by Philippe Ombredanne <pombredanne-od1rfyK75/E@public.gmane.org>
- Change jtag-aspeed.c licence type to
SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
and reorder line with license in description
Comments pointed by Kun Yi <kunyi-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
- Changed capability check for aspeed,ast2400-jtag/ast200-jtag
v11->v12
Comments pointed by Chip Bilbrey <chip-Gz1Ta9Qd61ZAfugRpC6u6w@public.gmane.org>
- Remove access mode from xfer and idle transactions
- Add new ioctl JTAG_SIOCMODE for set hw mode
v10->v11
v9->v10
V8->v9
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- add *data parameter to xfer function prototype
v7->v8
Comments pointed by Joel Stanley <joel.stan-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
- aspeed_jtag_init replace goto to return;
- change input variables type from __u32 to u32
in functios freq_get, freq_set, status_get
- change sm_ variables type from char to u8
- in jatg_init add disable clocks on error case
- remove release_mem_region on error case
- remove devm_free_irq on jtag_deinit
- Fix misspelling Disabe/Disable
- Change compatible string to ast2400 and ast2000
v6->v7
Notifications from kbuild test robot <lkp-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
- Add include <linux/types.h> to jtag-asapeed.c
v5->v6
v4->v5
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- Added HAS_IOMEM dependence in Kconfig to avoid
"undefined reference to `devm_ioremap_resource'" error,
because in some arch this not supported
v3->v4
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- change transaction pointer tdio type to __u64
- change internal status type from enum to __u32
v2->v3
v1->v2
Comments pointed by Greg KH <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
- change license type from GPLv2/BSD to GPLv2
Comments pointed by Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
- Add clk_prepare_enable/clk_disable_unprepare in clock init/deinit
- Change .compatible to soc-specific compatible names
aspeed,aspeed4000-jtag/aspeed5000-jtag
- Added dt-bindings
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- Reorder functions and removed the forward declarations
- Add static const qualifier to state machine states transitions
- Change .compatible to soc-specific compatible names
aspeed,aspeed4000-jtag/aspeed5000-jtag
- Add dt-bindings
Comments pointed by Randy Dunlap <rdunlap-wEGCiKHe2LqWVfeAwA7xHQ@public.gmane.org>
- Change module name jtag-aspeed in description in Kconfig
Comments pointed by kbuild test robot <lkp-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
- Remove invalid include <asm/mach-types.h>
- add resource_size instead of calculation
---
drivers/jtag/Kconfig | 13 +
drivers/jtag/Makefile | 1 +
drivers/jtag/jtag-aspeed.c | 783 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 797 insertions(+), 0 deletions(-)
create mode 100644 drivers/jtag/jtag-aspeed.c
diff --git a/drivers/jtag/Kconfig b/drivers/jtag/Kconfig
index 0fad1a3..098beb0 100644
--- a/drivers/jtag/Kconfig
+++ b/drivers/jtag/Kconfig
@@ -14,3 +14,16 @@ menuconfig JTAG
To compile this driver as a module, choose M here: the module will
be called jtag.
+
+menuconfig JTAG_ASPEED
+ tristate "Aspeed SoC JTAG controller support"
+ depends on JTAG && HAS_IOMEM
+ ---help---
+ This provides a support for Aspeed JTAG device, equipped on
+ Aspeed SoC 24xx and 25xx families. Drivers allows programming
+ of hardware devices, connected to SoC through the JTAG interface.
+
+ If you want this support, you should say Y here.
+
+ To compile this driver as a module, choose M here: the module will
+ be called jtag-aspeed.
diff --git a/drivers/jtag/Makefile b/drivers/jtag/Makefile
index af37493..04a855e 100644
--- a/drivers/jtag/Makefile
+++ b/drivers/jtag/Makefile
@@ -1 +1,2 @@
obj-$(CONFIG_JTAG) += jtag.o
+obj-$(CONFIG_JTAG_ASPEED) += jtag-aspeed.o
diff --git a/drivers/jtag/jtag-aspeed.c b/drivers/jtag/jtag-aspeed.c
new file mode 100644
index 0000000..99277d2
--- /dev/null
+++ b/drivers/jtag/jtag-aspeed.c
@@ -0,0 +1,783 @@
+// SPDX-License-Identifier: GPL-2.0
+// drivers/jtag/aspeed-jtag.c
+//
+// Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+// Copyright (c) 2017 Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/jtag.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <uapi/linux/jtag.h>
+
+#define ASPEED_JTAG_DATA 0x00
+#define ASPEED_JTAG_INST 0x04
+#define ASPEED_JTAG_CTRL 0x08
+#define ASPEED_JTAG_ISR 0x0C
+#define ASPEED_JTAG_SW 0x10
+#define ASPEED_JTAG_TCK 0x14
+#define ASPEED_JTAG_EC 0x18
+
+#define ASPEED_JTAG_DATA_MSB 0x01
+#define ASPEED_JTAG_DATA_CHUNK_SIZE 0x20
+
+/* ASPEED_JTAG_CTRL: Engine Control */
+#define ASPEED_JTAG_CTL_ENG_EN BIT(31)
+#define ASPEED_JTAG_CTL_ENG_OUT_EN BIT(30)
+#define ASPEED_JTAG_CTL_FORCE_TMS BIT(29)
+#define ASPEED_JTAG_CTL_INST_LEN(x) ((x) << 20)
+#define ASPEED_JTAG_CTL_LASPEED_INST BIT(17)
+#define ASPEED_JTAG_CTL_INST_EN BIT(16)
+#define ASPEED_JTAG_CTL_DR_UPDATE BIT(10)
+#define ASPEED_JTAG_CTL_DATA_LEN(x) ((x) << 4)
+#define ASPEED_JTAG_CTL_LASPEED_DATA BIT(1)
+#define ASPEED_JTAG_CTL_DATA_EN BIT(0)
+
+/* ASPEED_JTAG_ISR : Interrupt status and enable */
+#define ASPEED_JTAG_ISR_INST_PAUSE BIT(19)
+#define ASPEED_JTAG_ISR_INST_COMPLETE BIT(18)
+#define ASPEED_JTAG_ISR_DATA_PAUSE BIT(17)
+#define ASPEED_JTAG_ISR_DATA_COMPLETE BIT(16)
+#define ASPEED_JTAG_ISR_INST_PAUSE_EN BIT(3)
+#define ASPEED_JTAG_ISR_INST_COMPLETE_EN BIT(2)
+#define ASPEED_JTAG_ISR_DATA_PAUSE_EN BIT(1)
+#define ASPEED_JTAG_ISR_DATA_COMPLETE_EN BIT(0)
+#define ASPEED_JTAG_ISR_INT_EN_MASK GENMASK(3, 0)
+#define ASPEED_JTAG_ISR_INT_MASK GENMASK(19, 16)
+
+/* ASPEED_JTAG_SW : Software Mode and Status */
+#define ASPEED_JTAG_SW_MODE_EN BIT(19)
+#define ASPEED_JTAG_SW_MODE_TCK BIT(18)
+#define ASPEED_JTAG_SW_MODE_TMS BIT(17)
+#define ASPEED_JTAG_SW_MODE_TDIO BIT(16)
+
+/* ASPEED_JTAG_TCK : TCK Control */
+#define ASPEED_JTAG_TCK_DIVISOR_MASK GENMASK(10, 0)
+#define ASPEED_JTAG_TCK_GET_DIV(x) ((x) & ASPEED_JTAG_TCK_DIVISOR_MASK)
+
+/* ASPEED_JTAG_EC : Controller set for go to IDLE */
+#define ASPEED_JTAG_EC_GO_IDLE BIT(0)
+
+#define ASPEED_JTAG_IOUT_LEN(len) (ASPEED_JTAG_CTL_ENG_EN |\
+ ASPEED_JTAG_CTL_ENG_OUT_EN |\
+ ASPEED_JTAG_CTL_INST_LEN(len))
+
+#define ASPEED_JTAG_DOUT_LEN(len) (ASPEED_JTAG_CTL_ENG_EN |\
+ ASPEED_JTAG_CTL_ENG_OUT_EN |\
+ ASPEED_JTAG_CTL_DATA_LEN(len))
+
+#define ASPEED_JTAG_TCK_WAIT 10
+#define ASPEED_JTAG_RESET_CNTR 10
+
+#define ASPEED_JTAG_NAME "jtag-aspeed"
+
+struct aspeed_jtag {
+ void __iomem *reg_base;
+ struct device *dev;
+ struct clk *pclk;
+ enum jtag_endstate status;
+ int irq;
+ u32 flag;
+ wait_queue_head_t jtag_wq;
+ u32 mode;
+};
+
+static char *end_status_str[] = {"idle", "ir pause", "drpause"};
+
+static u32 aspeed_jtag_read(struct aspeed_jtag *aspeed_jtag, u32 reg)
+{
+ return readl(aspeed_jtag->reg_base + reg);
+}
+
+static void
+aspeed_jtag_write(struct aspeed_jtag *aspeed_jtag, u32 val, u32 reg)
+{
+ writel(val, aspeed_jtag->reg_base + reg);
+}
+
+static int aspeed_jtag_freq_set(struct jtag *jtag, u32 freq)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ unsigned long apb_frq;
+ u32 tck_val;
+ u16 div;
+
+ apb_frq = clk_get_rate(aspeed_jtag->pclk);
+ div = (apb_frq % freq == 0) ? (apb_frq / freq) - 1 : (apb_frq / freq);
+ tck_val = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_TCK);
+ aspeed_jtag_write(aspeed_jtag,
+ (tck_val & ASPEED_JTAG_TCK_DIVISOR_MASK) | div,
+ ASPEED_JTAG_TCK);
+ return 0;
+}
+
+static int aspeed_jtag_freq_get(struct jtag *jtag, u32 *frq)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ u32 pclk;
+ u32 tck;
+
+ pclk = clk_get_rate(aspeed_jtag->pclk);
+ tck = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_TCK);
+ *frq = pclk / (ASPEED_JTAG_TCK_GET_DIV(tck) + 1);
+
+ return 0;
+}
+
+static int aspeed_jtag_mode_set(struct jtag *jtag, u32 mode)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+
+ aspeed_jtag->mode = mode;
+ return 0;
+}
+
+static void aspeed_jtag_sw_delay(struct aspeed_jtag *aspeed_jtag, int cnt)
+{
+ int i;
+
+ for (i = 0; i < cnt; i++)
+ aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_SW);
+}
+
+static char aspeed_jtag_tck_cycle(struct aspeed_jtag *aspeed_jtag,
+ u8 tms, u8 tdi)
+{
+ char tdo = 0;
+
+ /* TCK = 0 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+
+ aspeed_jtag_sw_delay(aspeed_jtag, ASPEED_JTAG_TCK_WAIT);
+
+ /* TCK = 1 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TCK |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+
+ if (aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_SW) &
+ ASPEED_JTAG_SW_MODE_TDIO)
+ tdo = 1;
+
+ aspeed_jtag_sw_delay(aspeed_jtag, ASPEED_JTAG_TCK_WAIT);
+
+ /* TCK = 0 */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ (tms * ASPEED_JTAG_SW_MODE_TMS) |
+ (tdi * ASPEED_JTAG_SW_MODE_TDIO), ASPEED_JTAG_SW);
+ return tdo;
+}
+
+static void aspeed_jtag_wait_instruction_pause(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_INST_PAUSE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_INST_PAUSE;
+}
+
+static void
+aspeed_jtag_wait_instruction_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_INST_COMPLETE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_INST_COMPLETE;
+}
+
+static void
+aspeed_jtag_wait_data_pause_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_DATA_PAUSE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_DATA_PAUSE;
+}
+
+static void aspeed_jtag_wait_data_complete(struct aspeed_jtag *aspeed_jtag)
+{
+ wait_event_interruptible(aspeed_jtag->jtag_wq, aspeed_jtag->flag &
+ ASPEED_JTAG_ISR_DATA_COMPLETE);
+ aspeed_jtag->flag &= ~ASPEED_JTAG_ISR_DATA_COMPLETE;
+}
+
+static void aspeed_jtag_sm_cycle(struct aspeed_jtag *aspeed_jtag, const u8 *tms,
+ int len)
+{
+ int i;
+
+ for (i = 0; i < len; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, tms[i], 0);
+}
+
+static void aspeed_jtag_run_test_idle_sw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_run_test_idle *runtest)
+{
+ static const u8 sm_pause_irpause[] = {1, 1, 1, 1, 0, 1, 0};
+ static const u8 sm_pause_drpause[] = {1, 1, 1, 0, 1, 0};
+ static const u8 sm_idle_irpause[] = {1, 1, 0, 1, 0};
+ static const u8 sm_idle_drpause[] = {1, 0, 1, 0};
+ static const u8 sm_pause_idle[] = {1, 1, 0};
+ int i;
+
+ /* SW mode from idle/pause-> to pause/idle */
+ if (runtest->reset) {
+ for (i = 0; i < ASPEED_JTAG_RESET_CNTR; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, 1, 0);
+ }
+
+ switch (aspeed_jtag->status) {
+ case JTAG_STATE_IDLE:
+ switch (runtest->endstate) {
+ case JTAG_STATE_PAUSEIR:
+ /* ->DRSCan->IRSCan->IRCap->IRExit1->PauseIR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_idle_irpause,
+ sizeof(sm_idle_irpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEIR;
+ break;
+ case JTAG_STATE_PAUSEDR:
+ /* ->DRSCan->DRCap->DRExit1->PauseDR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_idle_drpause,
+ sizeof(sm_idle_drpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEDR;
+ break;
+ case JTAG_STATE_IDLE:
+ /* IDLE */
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ break;
+ default:
+ break;
+ }
+ break;
+
+ case JTAG_STATE_PAUSEIR:
+ /* Fall-through */
+ case JTAG_STATE_PAUSEDR:
+ /* From IR/DR Pause */
+ switch (runtest->endstate) {
+ case JTAG_STATE_PAUSEIR:
+ /*
+ * to Exit2 IR/DR->Updt IR/DR->DRSCan->IRSCan->IRCap->
+ * IRExit1->PauseIR
+ */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_irpause,
+ sizeof(sm_pause_irpause));
+
+ aspeed_jtag->status = JTAG_STATE_PAUSEIR;
+ break;
+ case JTAG_STATE_PAUSEDR:
+ /*
+ * to Exit2 IR/DR->Updt IR/DR->DRSCan->DRCap->
+ * DRExit1->PauseDR
+ */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_drpause,
+ sizeof(sm_pause_drpause));
+ aspeed_jtag->status = JTAG_STATE_PAUSEDR;
+ break;
+ case JTAG_STATE_IDLE:
+ /* to Exit2 IR/DR->Updt IR/DR->IDLE */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_idle,
+ sizeof(sm_pause_idle));
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ break;
+ default:
+ break;
+ }
+ break;
+
+ default:
+ dev_err(aspeed_jtag->dev, "aspeed_jtag_run_test_idle error\n");
+ break;
+ }
+
+ /* Stay on IDLE for at least TCK cycle */
+ for (i = 0; i < runtest->tck; i++)
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+}
+
+/**
+ * aspeed_jtag_run_test_idle:
+ * JTAG reset: generates at least 9 TMS high and 1 TMS low to force
+ * devices into Run-Test/Idle State.
+ */
+static int aspeed_jtag_idle(struct jtag *jtag,
+ struct jtag_run_test_idle *runtest)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+
+ dev_dbg(aspeed_jtag->dev, "aspeed_jtag runtest, status:%d, mode:%s, state:%s, reset:%d, tck:%d\n",
+ aspeed_jtag->status,
+ aspeed_jtag->mode & JTAG_XFER_HW_MODE ? "HW" : "SW",
+ end_status_str[runtest->endstate], runtest->reset,
+ runtest->tck);
+
+ if (!(aspeed_jtag->mode & JTAG_XFER_HW_MODE)) {
+ aspeed_jtag_run_test_idle_sw(aspeed_jtag, runtest);
+ return 0;
+ }
+
+ /* Disable sw mode */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_SW);
+ /* x TMS high + 1 TMS low */
+ if (runtest->reset)
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_CTL_ENG_EN |
+ ASPEED_JTAG_CTL_ENG_OUT_EN |
+ ASPEED_JTAG_CTL_FORCE_TMS, ASPEED_JTAG_CTRL);
+ else
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_EC_GO_IDLE,
+ ASPEED_JTAG_EC);
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ aspeed_jtag->status = JTAG_STATE_IDLE;
+ return 0;
+}
+
+static void aspeed_jtag_xfer_sw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_xfer *xfer, unsigned long *data)
+{
+ unsigned long remain_xfer = xfer->length;
+ unsigned long shift_bits = 0;
+ unsigned long index = 0;
+ unsigned long tdi;
+ char tdo;
+
+ if (xfer->direction == JTAG_READ_XFER)
+ tdi = UINT_MAX;
+ else
+ tdi = data[index];
+
+ while (remain_xfer > 1) {
+ tdo = aspeed_jtag_tck_cycle(aspeed_jtag, 0,
+ tdi & ASPEED_JTAG_DATA_MSB);
+ data[index] |= tdo << (shift_bits %
+ ASPEED_JTAG_DATA_CHUNK_SIZE);
+
+ tdi >>= 1;
+ shift_bits++;
+ remain_xfer--;
+
+ if (shift_bits % ASPEED_JTAG_DATA_CHUNK_SIZE == 0) {
+ dev_dbg(aspeed_jtag->dev, "R/W data[%lu]:%lx\n",
+ index, data[index]);
+
+ tdo = 0;
+ index++;
+
+ if (xfer->direction == JTAG_READ_XFER)
+ tdi = UINT_MAX;
+ else
+ tdi = data[index];
+ }
+ }
+
+ tdo = aspeed_jtag_tck_cycle(aspeed_jtag, 1, tdi & ASPEED_JTAG_DATA_MSB);
+ data[index] |= tdo << (shift_bits % ASPEED_JTAG_DATA_CHUNK_SIZE);
+}
+
+static void aspeed_jtag_xfer_push_data(struct aspeed_jtag *aspeed_jtag,
+ enum jtag_xfer_type type, u32 bits_len)
+{
+ dev_dbg(aspeed_jtag->dev, "shift bits %d\n", bits_len);
+
+ if (type == JTAG_SIR_XFER) {
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_IOUT_LEN(bits_len),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len) |
+ ASPEED_JTAG_CTL_INST_EN, ASPEED_JTAG_CTRL);
+ } else {
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_DOUT_LEN(bits_len) |
+ ASPEED_JTAG_CTL_DATA_EN, ASPEED_JTAG_CTRL);
+ }
+}
+
+static void aspeed_jtag_xfer_push_data_last(struct aspeed_jtag *aspeed_jtag,
+ enum jtag_xfer_type type,
+ u32 shift_bits,
+ enum jtag_endstate endstate)
+{
+ if (endstate != JTAG_STATE_IDLE) {
+ if (type == JTAG_SIR_XFER) {
+ dev_dbg(aspeed_jtag->dev, "IR Keep Pause\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits),
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_INST_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_instruction_pause(aspeed_jtag);
+ } else {
+ dev_dbg(aspeed_jtag->dev, "DR Keep Pause\n");
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_DR_UPDATE,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_DR_UPDATE |
+ ASPEED_JTAG_CTL_DATA_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_data_pause_complete(aspeed_jtag);
+ }
+ } else {
+ if (type == JTAG_SIR_XFER) {
+ dev_dbg(aspeed_jtag->dev, "IR go IDLE\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_INST,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_IOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_INST |
+ ASPEED_JTAG_CTL_INST_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_instruction_complete(aspeed_jtag);
+ } else {
+ dev_dbg(aspeed_jtag->dev, "DR go IDLE\n");
+
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_DATA,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag,
+ ASPEED_JTAG_DOUT_LEN(shift_bits) |
+ ASPEED_JTAG_CTL_LASPEED_DATA |
+ ASPEED_JTAG_CTL_DATA_EN,
+ ASPEED_JTAG_CTRL);
+ aspeed_jtag_wait_data_complete(aspeed_jtag);
+ }
+ }
+}
+
+static void aspeed_jtag_xfer_hw(struct aspeed_jtag *aspeed_jtag,
+ struct jtag_xfer *xfer, unsigned long *data)
+{
+ unsigned long remain_xfer = xfer->length;
+ unsigned long index = 0;
+ char shift_bits;
+ u32 data_reg;
+
+ data_reg = xfer->type == JTAG_SIR_XFER ?
+ ASPEED_JTAG_INST : ASPEED_JTAG_DATA;
+ while (remain_xfer) {
+ if (xfer->direction == JTAG_WRITE_XFER) {
+ dev_dbg(aspeed_jtag->dev, "W dr->dr_data[%lu]:%lx\n",
+ index, data[index]);
+
+ aspeed_jtag_write(aspeed_jtag, data[index], data_reg);
+ } else {
+ aspeed_jtag_write(aspeed_jtag, 0, data_reg);
+ }
+
+ if (remain_xfer > ASPEED_JTAG_DATA_CHUNK_SIZE) {
+ shift_bits = ASPEED_JTAG_DATA_CHUNK_SIZE;
+
+ /*
+ * Read bytes were not equals to column length
+ * and go to Pause-DR
+ */
+ aspeed_jtag_xfer_push_data(aspeed_jtag, xfer->type,
+ shift_bits);
+ } else {
+ /*
+ * Read bytes equals to column length =>
+ * Update-DR
+ */
+ shift_bits = remain_xfer;
+ aspeed_jtag_xfer_push_data_last(aspeed_jtag, xfer->type,
+ shift_bits,
+ xfer->endstate);
+ }
+
+ if (xfer->direction == JTAG_READ_XFER) {
+ if (shift_bits < ASPEED_JTAG_DATA_CHUNK_SIZE) {
+ data[index] = aspeed_jtag_read(aspeed_jtag,
+ data_reg);
+
+ data[index] >>= ASPEED_JTAG_DATA_CHUNK_SIZE -
+ shift_bits;
+ } else {
+ data[index] = aspeed_jtag_read(aspeed_jtag,
+ data_reg);
+ }
+ dev_dbg(aspeed_jtag->dev, "R dr->dr_data[%lu]:%lx\n",
+ index, data[index]);
+ }
+
+ remain_xfer = remain_xfer - shift_bits;
+ index++;
+ dev_dbg(aspeed_jtag->dev, "remain_xfer %lu\n", remain_xfer);
+ }
+}
+
+static int aspeed_jtag_xfer(struct jtag *jtag, struct jtag_xfer *xfer,
+ u8 *xfer_data)
+{
+ static const u8 sm_update_shiftir[] = {1, 1, 0, 0};
+ static const u8 sm_update_shiftdr[] = {1, 0, 0};
+ static const u8 sm_pause_idle[] = {1, 1, 0};
+ static const u8 sm_pause_update[] = {1, 1};
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+ unsigned long *data = (unsigned long *)xfer_data;
+ unsigned long remain_xfer = xfer->length;
+ unsigned long offset;
+ char dbg_str[256];
+ int pos = 0;
+ int i;
+
+ for (offset = 0, i = 0; offset < xfer->length;
+ offset += ASPEED_JTAG_DATA_CHUNK_SIZE, i++) {
+ pos += snprintf(&dbg_str[pos], sizeof(dbg_str) - pos,
+ "0x%08lx ", data[i]);
+ }
+
+ dev_dbg(aspeed_jtag->dev, "aspeed_jtag %s %s xfer, mode:%s, END:%d, len:%lu, TDI[%s]\n",
+ xfer->type == JTAG_SIR_XFER ? "SIR" : "SDR",
+ xfer->direction == JTAG_READ_XFER ? "READ" : "WRITE",
+ aspeed_jtag->mode & JTAG_XFER_HW_MODE ? "HW" : "SW",
+ xfer->endstate, remain_xfer, dbg_str);
+
+ if (!(aspeed_jtag->mode & JTAG_XFER_HW_MODE)) {
+ /* SW mode */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ if (aspeed_jtag->status != JTAG_STATE_IDLE) {
+ /*IR/DR Pause->Exit2 IR / DR->Update IR /DR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_update,
+ sizeof(sm_pause_update));
+ }
+
+ if (xfer->type == JTAG_SIR_XFER)
+ /* ->IRSCan->CapIR->ShiftIR */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_update_shiftir,
+ sizeof(sm_update_shiftir));
+ else
+ /* ->DRScan->DRCap->DRShift */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_update_shiftdr,
+ sizeof(sm_update_shiftdr));
+
+ aspeed_jtag_xfer_sw(aspeed_jtag, xfer, data);
+
+ /* DIPause/DRPause */
+ aspeed_jtag_tck_cycle(aspeed_jtag, 0, 0);
+
+ if (xfer->endstate == JTAG_STATE_IDLE) {
+ /* ->DRExit2->DRUpdate->IDLE */
+ aspeed_jtag_sm_cycle(aspeed_jtag, sm_pause_idle,
+ sizeof(sm_pause_idle));
+ }
+ } else {
+ /* hw mode */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_SW);
+ aspeed_jtag_xfer_hw(aspeed_jtag, xfer, data);
+ }
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+ aspeed_jtag->status = xfer->endstate;
+ return 0;
+}
+
+static int aspeed_jtag_status_get(struct jtag *jtag, u32 *status)
+{
+ struct aspeed_jtag *aspeed_jtag = jtag_priv(jtag);
+
+ *status = aspeed_jtag->status;
+ return 0;
+}
+
+static irqreturn_t aspeed_jtag_interrupt(s32 this_irq, void *dev_id)
+{
+ struct aspeed_jtag *aspeed_jtag = dev_id;
+ irqreturn_t ret;
+ u32 status;
+
+ status = aspeed_jtag_read(aspeed_jtag, ASPEED_JTAG_ISR);
+ dev_dbg(aspeed_jtag->dev, "status %x\n", status);
+
+ if (status & ASPEED_JTAG_ISR_INT_MASK) {
+ aspeed_jtag_write(aspeed_jtag,
+ (status & ASPEED_JTAG_ISR_INT_MASK)
+ | (status & ASPEED_JTAG_ISR_INT_EN_MASK),
+ ASPEED_JTAG_ISR);
+ aspeed_jtag->flag |= status & ASPEED_JTAG_ISR_INT_MASK;
+ }
+
+ if (aspeed_jtag->flag) {
+ wake_up_interruptible(&aspeed_jtag->jtag_wq);
+ ret = IRQ_HANDLED;
+ } else {
+ dev_err(aspeed_jtag->dev, "aspeed_jtag irq status:%x\n",
+ status);
+ ret = IRQ_NONE;
+ }
+ return ret;
+}
+
+int aspeed_jtag_init(struct platform_device *pdev,
+ struct aspeed_jtag *aspeed_jtag)
+{
+ struct resource *res;
+ int err;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ aspeed_jtag->reg_base = devm_ioremap_resource(aspeed_jtag->dev, res);
+ if (IS_ERR(aspeed_jtag->reg_base))
+ return -ENOMEM;
+
+ aspeed_jtag->pclk = devm_clk_get(aspeed_jtag->dev, NULL);
+ if (IS_ERR(aspeed_jtag->pclk)) {
+ dev_err(aspeed_jtag->dev, "devm_clk_get failed\n");
+ return PTR_ERR(aspeed_jtag->pclk);
+ }
+
+ clk_prepare_enable(aspeed_jtag->pclk);
+
+ aspeed_jtag->irq = platform_get_irq(pdev, 0);
+ if (aspeed_jtag->irq < 0) {
+ dev_err(aspeed_jtag->dev, "no irq specified\n");
+ err = -ENOENT;
+ goto clk_unprep;
+ }
+
+ /* Enable clock */
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_CTL_ENG_EN |
+ ASPEED_JTAG_CTL_ENG_OUT_EN, ASPEED_JTAG_CTRL);
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_SW_MODE_EN |
+ ASPEED_JTAG_SW_MODE_TDIO, ASPEED_JTAG_SW);
+
+ err = devm_request_irq(aspeed_jtag->dev, aspeed_jtag->irq,
+ aspeed_jtag_interrupt, 0,
+ "aspeed-jtag", aspeed_jtag);
+ if (err) {
+ dev_err(aspeed_jtag->dev, "aspeed_jtag unable to get IRQ");
+ goto clk_unprep;
+ }
+ dev_dbg(&pdev->dev, "aspeed_jtag:IRQ %d.\n", aspeed_jtag->irq);
+
+ aspeed_jtag_write(aspeed_jtag, ASPEED_JTAG_ISR_INST_PAUSE |
+ ASPEED_JTAG_ISR_INST_COMPLETE |
+ ASPEED_JTAG_ISR_DATA_PAUSE |
+ ASPEED_JTAG_ISR_DATA_COMPLETE |
+ ASPEED_JTAG_ISR_INST_PAUSE_EN |
+ ASPEED_JTAG_ISR_INST_COMPLETE_EN |
+ ASPEED_JTAG_ISR_DATA_PAUSE_EN |
+ ASPEED_JTAG_ISR_DATA_COMPLETE_EN,
+ ASPEED_JTAG_ISR);
+
+ aspeed_jtag->flag = 0;
+ aspeed_jtag->mode = 0;
+ init_waitqueue_head(&aspeed_jtag->jtag_wq);
+ return 0;
+
+clk_unprep:
+ clk_disable_unprepare(aspeed_jtag->pclk);
+ return err;
+}
+
+int aspeed_jtag_deinit(struct platform_device *pdev,
+ struct aspeed_jtag *aspeed_jtag)
+{
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_ISR);
+ /* Disable clock */
+ aspeed_jtag_write(aspeed_jtag, 0, ASPEED_JTAG_CTRL);
+ clk_disable_unprepare(aspeed_jtag->pclk);
+ return 0;
+}
+
+static const struct jtag_ops aspeed_jtag_ops = {
+ .freq_get = aspeed_jtag_freq_get,
+ .freq_set = aspeed_jtag_freq_set,
+ .status_get = aspeed_jtag_status_get,
+ .idle = aspeed_jtag_idle,
+ .xfer = aspeed_jtag_xfer,
+ .mode_set = aspeed_jtag_mode_set
+};
+
+static int aspeed_jtag_probe(struct platform_device *pdev)
+{
+ struct aspeed_jtag *aspeed_jtag;
+ struct device *dev;
+ struct jtag *jtag;
+ int err;
+
+ dev = &pdev->dev;
+ if (!of_device_is_compatible(pdev->dev.of_node,
+ "aspeed,ast2500-jtag") &&
+ !of_device_is_compatible(pdev->dev.of_node,
+ "aspeed,ast2400-jtag"))
+ return -ENODEV;
+
+ jtag = jtag_alloc(sizeof(*aspeed_jtag), &aspeed_jtag_ops);
+ if (!jtag)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, jtag);
+ aspeed_jtag = jtag_priv(jtag);
+ aspeed_jtag->dev = &pdev->dev;
+
+ /* Initialize device*/
+ err = aspeed_jtag_init(pdev, aspeed_jtag);
+ if (err)
+ goto err_jtag_init;
+
+ /* Initialize JTAG core structure*/
+ err = jtag_register(jtag);
+ if (err)
+ goto err_jtag_register;
+
+ return 0;
+
+err_jtag_register:
+ aspeed_jtag_deinit(pdev, aspeed_jtag);
+err_jtag_init:
+ jtag_free(jtag);
+ return err;
+}
+
+static int aspeed_jtag_remove(struct platform_device *pdev)
+{
+ struct jtag *jtag;
+
+ jtag = platform_get_drvdata(pdev);
+ aspeed_jtag_deinit(pdev, jtag_priv(jtag));
+ jtag_unregister(jtag);
+ jtag_free(jtag);
+ return 0;
+}
+
+static const struct of_device_id aspeed_jtag_of_match[] = {
+ { .compatible = "aspeed,ast2400-jtag", },
+ { .compatible = "aspeed,ast2500-jtag", },
+ {}
+};
+
+static struct platform_driver aspeed_jtag_driver = {
+ .probe = aspeed_jtag_probe,
+ .remove = aspeed_jtag_remove,
+ .driver = {
+ .name = ASPEED_JTAG_NAME,
+ .of_match_table = aspeed_jtag_of_match,
+ },
+};
+module_platform_driver(aspeed_jtag_driver);
+
+MODULE_AUTHOR("Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>");
+MODULE_DESCRIPTION("ASPEED JTAG driver");
+MODULE_LICENSE("GPL v2");
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [patch v14 1/4] drivers: jtag: Add JTAG core driver
From: Oleksandr Shamray @ 2017-12-14 16:29 UTC (permalink / raw)
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, arnd-r2nGTMty4D4
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ,
joel-U3u1mxZcP9KHXe+LvDLADg, jiri-rHqAuBHg3fBzbRFIqnYvSA,
tklauser-93Khv+1bN0NyDzI6CaY1VQ,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
vadimp-VPRAkNaXOzVWk0Htik3J/w,
system-sw-low-level-VPRAkNaXOzVWk0Htik3J/w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
openocd-devel-owner-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f,
linux-api-u79uwXL29TY76Z2rM5mHXA, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, Oleksandr Shamray, Jiri Pirko
In-Reply-To: <1513268971-13518-1-git-send-email-oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Initial patch for JTAG driver
JTAG class driver provide infrastructure to support hardware/software
JTAG platform drivers. It provide user layer API interface for flashing
and debugging external devices which equipped with JTAG interface
using standard transactions.
Driver exposes set of IOCTL to user space for:
- XFER:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks).
- SIOCFREQ/GIOCFREQ for setting and reading JTAG frequency.
Driver core provides set of internal APIs for allocation and
registration:
- jtag_register;
- jtag_unregister;
- jtag_alloc;
- jtag_free;
Platform driver on registration with jtag-core creates the next
entry in dev folder:
/dev/jtagX
Signed-off-by: Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
Signed-off-by: Jiri Pirko <jiri-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
---
v13->v14
Comments pointed by Philippe Ombredanne <pombredanne-od1rfyK75/E@public.gmane.org>
- Change style of head block comment from /**/ to //
v12->v13
Comments pointed by Philippe Ombredanne <pombredanne-od1rfyK75/E@public.gmane.org>
- Change jtag.c licence type to
SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
and reorder line with license in description
v11->v12
Comments pointed by Greg KH <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
- Change jtag.h licence type to
SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
and reorder line with license in description
Chip Bilbrey <chip-Gz1Ta9Qd61ZAfugRpC6u6w@public.gmane.org>
- Remove Apeed reference from uapi jtag.h header
- Remove access mode from xfer and idle transactions
- Add new ioctl JTAG_SIOCMODE for set hw mode
- Add only one open per JTAG port blocking with mutex blocking
v10->v11
Notifications from kbuild test robot <lkp-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
- include types.h headeri to jtag.h
- fix incompatible type of xfer callback
- remove rdundant class defination
- Fix return order in case of xfer error
V9->v10
Comments pointed by Greg KH <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
- remove unnecessary alignment for pirv data
- move jtag_copy_to_user and jtag_copy_from_user code just to ioctl
- move int jtag_run_test_idle_op and jtag_xfer_op code
just to ioctl
- change return error codes to more applicable
- add missing error checks
- fix error check order in ioctl
- remove unnecessary blank lines
- add param validation to ioctl
- remove compat_ioctl
- remove only one open per JTAG port blocking.
User will care about this.
- Fix idr memory leak on jtag_exit
- change cdev device type to misc
V8->v9
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- use get_user() instead of __get_user().
- change jtag->open type from int to atomic_t
- remove spinlock on jtg_open
- remove mutex on jtag_register
- add unregister_chrdev_region on jtag_init err
- add unregister_chrdev_region on jtag_exit
- remove unnecessary pointer casts
- add *data parameter to xfer function prototype
v7->v8
Comments pointed by Moritz Fischer <moritz.fischer-+aYTwkv1SeIAvxtiuMwx3w@public.gmane.org>
- Fix misspelling s/friver/driver
v6->v7
Notifications from kbuild test robot <lkp-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
- Remove include asm/types.h from jtag.h
- Add include <linux/types.h> to jtag.c
v5->v6
v4->v5
v3->v4
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- change transaction pointer tdio type to __u64
- change internal status type from enum to __u32
- reorder jtag_xfer members to avoid the implied padding
- add __packed attribute to jtag_xfer and jtag_run_test_idle
v2->v3
Notifications from kbuild test robot <lkp-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org>
- Change include path to <linux/types.h> in jtag.h
v1->v2
Comments pointed by Greg KH <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
- Change license type from GPLv2/BSD to GPLv2
- Change type of variables which crossed user/kernel to __type
- Remove "default n" from Kconfig
Comments pointed by Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>
- Change list_add_tail in jtag_unregister to list_del
Comments pointed by Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
- Add SPDX-License-Identifier instead of license text
Comments pointed by Arnd Bergmann <arnd-r2nGTMty4D4@public.gmane.org>
- Change __copy_to_user to memdup_user
- Change __put_user to put_user
- Change type of variables to __type for compatible 32 and 64-bit systems
- Add check for maximum xfer data size
- Change lookup data mechanism to get jtag data from inode
- Add .compat_ioctl to file ops
- Add mem alignment for jtag priv data
Comments pointed by Tobias Klauser <tklauser-93Khv+1bN0NyDzI6CaY1VQ@public.gmane.org>
- Change function names to avoid match with variable types
- Fix description for jtag_ru_test_idle in uapi jtag.h
- Fix misprints IDEL/IDLE, trough/through
---
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 10 ++
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 16 ++
drivers/jtag/Makefile | 1 +
drivers/jtag/jtag.c | 288 ++++++++++++++++++++++++++++++++++
include/linux/jtag.h | 45 ++++++
include/uapi/linux/jtag.h | 104 ++++++++++++
9 files changed, 469 insertions(+), 0 deletions(-)
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
diff --git a/Documentation/ioctl/ioctl-number.txt b/Documentation/ioctl/ioctl-number.txt
index 3e3fdae..1af2508 100644
--- a/Documentation/ioctl/ioctl-number.txt
+++ b/Documentation/ioctl/ioctl-number.txt
@@ -321,6 +321,8 @@ Code Seq#(hex) Include File Comments
0xB0 all RATIO devices in development:
<mailto:vgo-/IYFIZglx74@public.gmane.org>
0xB1 00-1F PPPoX <mailto:mostrows-TTukF6hB3AoKZpuMuFhwt/d9D2ou9A/h@public.gmane.org>
+0xB2 00-0f linux/jtag.h JTAG driver
+ <mailto:oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
0xB3 00 linux/mmc/ioctl.h
0xB4 00-0F linux/gpio.h <mailto:linux-gpio-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
0xB5 00-0F uapi/linux/rpmsg.h <mailto:linux-remoteproc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
diff --git a/MAINTAINERS b/MAINTAINERS
index 205d397..dfcf49c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7292,6 +7292,16 @@ L: linux-serial-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
S: Maintained
F: drivers/tty/serial/jsm/
+JTAG SUBSYSTEM
+M: Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+M: Vadim Pasternak <vadimp-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+S: Maintained
+F: include/linux/jtag.h
+F: include/uapi/linux/jtag.h
+F: drivers/jtag/
+F: Documentation/devicetree/bindings/jtag/
+F: Documentation/ABI/testing/jtag-cdev
+
K10TEMP HARDWARE MONITORING DRIVER
M: Clemens Ladisch <clemens-P6GI/4k7KOmELgA04lAiVw@public.gmane.org>
L: linux-hwmon-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 505c676..2214678 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -208,4 +208,6 @@ source "drivers/tee/Kconfig"
source "drivers/mux/Kconfig"
+source "drivers/jtag/Kconfig"
+
endmenu
diff --git a/drivers/Makefile b/drivers/Makefile
index dfdcda0..6a2059b 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -182,3 +182,4 @@ obj-$(CONFIG_FPGA) += fpga/
obj-$(CONFIG_FSI) += fsi/
obj-$(CONFIG_TEE) += tee/
obj-$(CONFIG_MULTIPLEXER) += mux/
+obj-$(CONFIG_JTAG) += jtag/
diff --git a/drivers/jtag/Kconfig b/drivers/jtag/Kconfig
new file mode 100644
index 0000000..0fad1a3
--- /dev/null
+++ b/drivers/jtag/Kconfig
@@ -0,0 +1,16 @@
+menuconfig JTAG
+ tristate "JTAG support"
+ ---help---
+ This provides basic core functionality support for jtag class devices
+ Hardware equipped with JTAG microcontroller which can be built
+ on top of this drivers. Driver exposes the set of IOCTL to the
+ user space for:
+ SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
+ SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
+ RUNTEST (Forces IEEE 1149.1 bus to a run state for specified
+ number of clocks).
+
+ If you want this support, you should say Y here.
+
+ To compile this driver as a module, choose M here: the module will
+ be called jtag.
diff --git a/drivers/jtag/Makefile b/drivers/jtag/Makefile
new file mode 100644
index 0000000..af37493
--- /dev/null
+++ b/drivers/jtag/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_JTAG) += jtag.o
diff --git a/drivers/jtag/jtag.c b/drivers/jtag/jtag.c
new file mode 100644
index 0000000..39cbce9
--- /dev/null
+++ b/drivers/jtag/jtag.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0
+// drivers/jtag/jtag.c
+//
+// Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+// Copyright (c) 2017 Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+
+#include <linux/cdev.h>
+#include <linux/device.h>
+#include <linux/jtag.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/rtnetlink.h>
+#include <linux/spinlock.h>
+#include <linux/types.h>
+#include <uapi/linux/jtag.h>
+
+#define JTAG_NAME "jtag0"
+#define MAX_JTAG_NAME_LEN (sizeof("jtag") + 5)
+
+struct jtag {
+ struct miscdevice miscdev;
+ struct device *dev;
+ const struct jtag_ops *ops;
+ int id;
+ bool opened;
+ struct mutex open_lock;
+ unsigned long priv[0];
+};
+
+static DEFINE_IDA(jtag_ida);
+
+void *jtag_priv(struct jtag *jtag)
+{
+ return jtag->priv;
+}
+EXPORT_SYMBOL_GPL(jtag_priv);
+
+static long jtag_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
+{
+ struct jtag *jtag = file->private_data;
+ struct jtag_run_test_idle idle;
+ struct jtag_xfer xfer;
+ u8 *xfer_data;
+ u32 data_size;
+ u32 value;
+ int err;
+
+ if (!arg)
+ return -EINVAL;
+
+ switch (cmd) {
+ case JTAG_GIOCFREQ:
+
+ if (jtag->ops->freq_get)
+ err = jtag->ops->freq_get(jtag, &value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ if (put_user(value, (__u32 *)arg))
+ err = -EFAULT;
+ break;
+
+ case JTAG_SIOCFREQ:
+ if (get_user(value, (__u32 *)arg))
+ return -EFAULT;
+ if (value == 0)
+ return -EINVAL;
+
+ if (jtag->ops->freq_set)
+ err = jtag->ops->freq_set(jtag, value);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ case JTAG_IOCRUNTEST:
+ if (copy_from_user(&idle, (void *)arg,
+ sizeof(struct jtag_run_test_idle)))
+ return -EFAULT;
+
+ if (idle.endstate > JTAG_STATE_PAUSEDR)
+ return -EINVAL;
+
+ if (jtag->ops->idle)
+ err = jtag->ops->idle(jtag, &idle);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ case JTAG_IOCXFER:
+ if (copy_from_user(&xfer, (void *)arg,
+ sizeof(struct jtag_xfer)))
+ return -EFAULT;
+
+ if (xfer.length >= JTAG_MAX_XFER_DATA_LEN)
+ return -EINVAL;
+
+ if (xfer.type > JTAG_SDR_XFER)
+ return -EINVAL;
+
+ if (xfer.direction > JTAG_WRITE_XFER)
+ return -EINVAL;
+
+ if (xfer.endstate > JTAG_STATE_PAUSEDR)
+ return -EINVAL;
+
+ data_size = DIV_ROUND_UP(xfer.length, BITS_PER_BYTE);
+ xfer_data = memdup_user(u64_to_user_ptr(xfer.tdio), data_size);
+
+ if (!xfer_data)
+ return -EFAULT;
+
+ if (jtag->ops->xfer) {
+ err = jtag->ops->xfer(jtag, &xfer, xfer_data);
+ } else {
+ kfree(xfer_data);
+ return -EOPNOTSUPP;
+ }
+
+ if (err) {
+ kfree(xfer_data);
+ return -EFAULT;
+ }
+
+ err = copy_to_user(u64_to_user_ptr(xfer.tdio),
+ (void *)(xfer_data), data_size);
+
+ if (err) {
+ kfree(xfer_data);
+ return -EFAULT;
+ }
+
+ kfree(xfer_data);
+ if (copy_to_user((void *)arg, &xfer, sizeof(struct jtag_xfer)))
+ return -EFAULT;
+ break;
+
+ case JTAG_GIOCSTATUS:
+ if (jtag->ops->status_get)
+ err = jtag->ops->status_get(jtag, &value);
+ else
+ err = -EOPNOTSUPP;
+ if (err)
+ break;
+
+ err = put_user(value, (__u32 *)arg);
+ if (err)
+ err = -EFAULT;
+ break;
+ case JTAG_SIOCMODE:
+ if (get_user(value, (__u32 *)arg))
+ return -EFAULT;
+ if (value == 0)
+ return -EINVAL;
+
+ if (jtag->ops->mode_set)
+ err = jtag->ops->mode_set(jtag, value);
+ else
+ err = -EOPNOTSUPP;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+ return err;
+}
+
+static int jtag_open(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = container_of(file->private_data, struct jtag,
+ miscdev);
+
+ if (mutex_lock_interruptible(&jtag->open_lock))
+ return -ERESTARTSYS;
+
+ if (jtag->opened) {
+ mutex_unlock(&jtag->open_lock);
+ return -EINVAL;
+ }
+
+ nonseekable_open(inode, file);
+ file->private_data = jtag;
+ jtag->opened = true;
+ mutex_unlock(&jtag->open_lock);
+ return 0;
+}
+
+static int jtag_release(struct inode *inode, struct file *file)
+{
+ struct jtag *jtag = file->private_data;
+
+ mutex_lock(&jtag->open_lock);
+ jtag->opened = false;
+ mutex_unlock(&jtag->open_lock);
+ return 0;
+}
+
+static const struct file_operations jtag_fops = {
+ .owner = THIS_MODULE,
+ .open = jtag_open,
+ .release = jtag_release,
+ .llseek = noop_llseek,
+ .unlocked_ioctl = jtag_ioctl,
+};
+
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops)
+{
+ struct jtag *jtag;
+
+ jtag = kzalloc(sizeof(*jtag) + round_up(priv_size, ARCH_DMA_MINALIGN),
+ GFP_KERNEL);
+ if (!jtag)
+ return NULL;
+
+ jtag->ops = ops;
+ return jtag;
+}
+EXPORT_SYMBOL_GPL(jtag_alloc);
+
+void jtag_free(struct jtag *jtag)
+{
+ kfree(jtag);
+}
+EXPORT_SYMBOL_GPL(jtag_free);
+
+int jtag_register(struct jtag *jtag)
+{
+ char *name;
+ int err;
+ int id;
+
+ id = ida_simple_get(&jtag_ida, 0, 0, GFP_KERNEL);
+ if (id < 0)
+ return id;
+
+ jtag->id = id;
+
+ name = kzalloc(MAX_JTAG_NAME_LEN, GFP_KERNEL);
+ if (!name) {
+ err = -ENOMEM;
+ goto err_jtag_alloc;
+ }
+
+ err = snprintf(name, MAX_JTAG_NAME_LEN, "jtag%d", id);
+ if (err < 0)
+ goto err_jtag_name;
+
+ mutex_init(&jtag->open_lock);
+ jtag->miscdev.fops = &jtag_fops;
+ jtag->miscdev.minor = MISC_DYNAMIC_MINOR;
+ jtag->miscdev.name = name;
+
+ err = misc_register(&jtag->miscdev);
+ if (err)
+ dev_err(jtag->dev, "Unable to register device\n");
+ else
+ return 0;
+ jtag->opened = false;
+
+err_jtag_name:
+ kfree(name);
+err_jtag_alloc:
+ ida_simple_remove(&jtag_ida, id);
+ return err;
+}
+EXPORT_SYMBOL_GPL(jtag_register);
+
+void jtag_unregister(struct jtag *jtag)
+{
+ misc_deregister(&jtag->miscdev);
+ kfree(jtag->miscdev.name);
+ ida_simple_remove(&jtag_ida, jtag->id);
+}
+EXPORT_SYMBOL_GPL(jtag_unregister);
+
+static void __exit jtag_exit(void)
+{
+ ida_destroy(&jtag_ida);
+}
+
+module_exit(jtag_exit);
+
+MODULE_AUTHOR("Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>");
+MODULE_DESCRIPTION("Generic jtag support");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/jtag.h b/include/linux/jtag.h
new file mode 100644
index 0000000..312c641
--- /dev/null
+++ b/include/linux/jtag.h
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+// include/linux/jtag.h - JTAG class driver
+//
+// Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+// Copyright (c) 2017 Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+
+#ifndef __JTAG_H
+#define __JTAG_H
+
+#include <uapi/linux/jtag.h>
+
+#ifndef ARCH_DMA_MINALIGN
+#define ARCH_DMA_MINALIGN 1
+#endif
+
+#define jtag_u64_to_ptr(arg) ((void *)(uintptr_t)arg)
+
+#define JTAG_MAX_XFER_DATA_LEN 65535
+
+struct jtag;
+/**
+ * struct jtag_ops - callbacks for jtag control functions:
+ *
+ * @freq_get: get frequency function. Filled by device driver
+ * @freq_set: set frequency function. Filled by device driver
+ * @status_get: set status function. Filled by device driver
+ * @idle: set JTAG to idle state function. Filled by device driver
+ * @xfer: send JTAG xfer function. Filled by device driver
+ */
+struct jtag_ops {
+ int (*freq_get)(struct jtag *jtag, u32 *freq);
+ int (*freq_set)(struct jtag *jtag, u32 freq);
+ int (*status_get)(struct jtag *jtag, u32 *state);
+ int (*idle)(struct jtag *jtag, struct jtag_run_test_idle *idle);
+ int (*xfer)(struct jtag *jtag, struct jtag_xfer *xfer, u8 *xfer_data);
+ int (*mode_set)(struct jtag *jtag, u32 mode_mask);
+};
+
+void *jtag_priv(struct jtag *jtag);
+int jtag_register(struct jtag *jtag);
+void jtag_unregister(struct jtag *jtag);
+struct jtag *jtag_alloc(size_t priv_size, const struct jtag_ops *ops);
+void jtag_free(struct jtag *jtag);
+
+#endif /* __JTAG_H */
diff --git a/include/uapi/linux/jtag.h b/include/uapi/linux/jtag.h
new file mode 100644
index 0000000..cda2520
--- /dev/null
+++ b/include/uapi/linux/jtag.h
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note
+// include/uapi/linux/jtag.h - JTAG class driver uapi
+//
+// Copyright (c) 2017 Mellanox Technologies. All rights reserved.
+// Copyright (c) 2017 Oleksandr Shamray <oleksandrs-VPRAkNaXOzVWk0Htik3J/w@public.gmane.org>
+
+#ifndef __UAPI_LINUX_JTAG_H
+#define __UAPI_LINUX_JTAG_H
+
+#include <linux/types.h>
+/*
+ * JTAG_XFER_HW_MODE: JTAG hardware mode. Used to set HW drived or bitbang
+ * mode. This is bitmask param of ioctl JTAG_SIOCMODE command
+ */
+#define JTAG_XFER_HW_MODE 1
+
+/**
+ * enum jtag_endstate:
+ *
+ * @JTAG_STATE_IDLE: JTAG state machine IDLE state
+ * @JTAG_STATE_PAUSEIR: JTAG state machine PAUSE_IR state
+ * @JTAG_STATE_PAUSEDR: JTAG state machine PAUSE_DR state
+ */
+enum jtag_endstate {
+ JTAG_STATE_IDLE,
+ JTAG_STATE_PAUSEIR,
+ JTAG_STATE_PAUSEDR,
+};
+
+/**
+ * enum jtag_xfer_type:
+ *
+ * @JTAG_SIR_XFER: SIR transfer
+ * @JTAG_SDR_XFER: SDR transfer
+ */
+enum jtag_xfer_type {
+ JTAG_SIR_XFER,
+ JTAG_SDR_XFER,
+};
+
+/**
+ * enum jtag_xfer_direction:
+ *
+ * @JTAG_READ_XFER: read transfer
+ * @JTAG_WRITE_XFER: write transfer
+ */
+enum jtag_xfer_direction {
+ JTAG_READ_XFER,
+ JTAG_WRITE_XFER,
+};
+
+/**
+ * struct jtag_run_test_idle - forces JTAG state machine to
+ * RUN_TEST/IDLE state
+ *
+ * @reset: 0 - run IDLE/PAUSE from current state
+ * 1 - go through TEST_LOGIC/RESET state before IDLE/PAUSE
+ * @end: completion flag
+ * @tck: clock counter
+ *
+ * Structure represents interface to JTAG device for jtag idle
+ * execution.
+ */
+struct jtag_run_test_idle {
+ __u8 reset;
+ __u8 endstate;
+ __u8 tck;
+};
+
+/**
+ * struct jtag_xfer - jtag xfer:
+ *
+ * @type: transfer type
+ * @direction: xfer direction
+ * @length: xfer bits len
+ * @tdio : xfer data array
+ * @endir: xfer end state
+ *
+ * Structure represents interface to JTAG device for jtag sdr xfer
+ * execution.
+ */
+struct jtag_xfer {
+ __u8 type;
+ __u8 direction;
+ __u8 endstate;
+ __u32 length;
+ __u64 tdio;
+};
+
+/* ioctl interface */
+#define __JTAG_IOCTL_MAGIC 0xb2
+
+#define JTAG_IOCRUNTEST _IOW(__JTAG_IOCTL_MAGIC, 0,\
+ struct jtag_run_test_idle)
+#define JTAG_SIOCFREQ _IOW(__JTAG_IOCTL_MAGIC, 1, unsigned int)
+#define JTAG_GIOCFREQ _IOR(__JTAG_IOCTL_MAGIC, 2, unsigned int)
+#define JTAG_IOCXFER _IOWR(__JTAG_IOCTL_MAGIC, 3, struct jtag_xfer)
+#define JTAG_GIOCSTATUS _IOWR(__JTAG_IOCTL_MAGIC, 4, enum jtag_endstate)
+#define JTAG_SIOCMODE _IOW(__JTAG_IOCTL_MAGIC, 5, unsigned int)
+
+#define JTAG_FIRST_MINOR 0
+#define JTAG_MAX_DEVICES 32
+
+#endif /* __UAPI_LINUX_JTAG_H */
--
1.7.1
^ permalink raw reply related
* [patch v14 0/4] JTAG driver introduction
From: Oleksandr Shamray @ 2017-12-14 16:29 UTC (permalink / raw)
To: gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r, arnd-r2nGTMty4D4
Cc: linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA, openbmc-uLR06cmDAlY/bJ5BZ2RsiQ,
joel-U3u1mxZcP9KHXe+LvDLADg, jiri-rHqAuBHg3fBzbRFIqnYvSA,
tklauser-93Khv+1bN0NyDzI6CaY1VQ,
linux-serial-u79uwXL29TY76Z2rM5mHXA,
vadimp-VPRAkNaXOzVWk0Htik3J/w,
system-sw-low-level-VPRAkNaXOzVWk0Htik3J/w,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
openocd-devel-owner-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f,
linux-api-u79uwXL29TY76Z2rM5mHXA, davem-fT/PcQaiUtIeIZ0/mPfg9Q,
mchehab-DgEjT+Ai2ygdnm+yROfE0A, Oleksandr Shamray
When a need raise up to use JTAG interface for system's devices
programming or CPU debugging, usually the user layer
application implements jtag protocol by bit-bang or using a
proprietary connection to vendor hardware.
This method can be slow and not generic.
We propose to implement general JTAG interface and infrastructure
to communicate with user layer application. In such way, we can
have the standard JTAG interface core part and separation from
specific HW implementation.
This allow new capability to debug the CPU or program system's
device via BMC without additional devices nor cost.
This patch purpose is to add JTAG master core infrastructure by
defining new JTAG class and provide generic JTAG interface
to allow hardware specific drivers to connect this interface.
This will enable all JTAG drivers to use the common interface
part and will have separate for hardware implementation.
The JTAG (Joint Test Action Group) core driver provides minimal generic
JTAG interface, which can be used by hardware specific JTAG master
controllers. By providing common interface for the JTAG controllers,
user space device programing is hardware independent.
Modern SoC which in use for embedded system' equipped with
internal JTAG master interface.
This interface is used for programming and debugging system's
hardware components, like CPLD, FPGA, CPU, voltage and
industrial controllers.
Firmware for such devices can be upgraded through JTAG interface during
Runtime. The JTAG standard support for multiple devices programming,
is in case their lines are daisy-chained together.
For example, systems which equipped with host CPU, BMC SoC or/and
number of programmable devices are capable to connect a pin and
select system components dynamically for programming and debugging,
This is using by the BMC which is equipped with internal SoC master
controller.
For example:
BMC JTAG master --> pin selected to CPLDs chain for programming (filed
upgrade, production)
BMC JTAG master --> pin selected to voltage monitors for programming
(field upgrade, production)
BMC JTAG master --> pin selected to host CPU (on-site debugging
and developers debugging)
For example, we can have application in user space which using calls
to JTAG driver executes CPLD programming directly from SVF file
The JTAG standard (IEEE 1149.1) defines the next connector pins:
- TDI (Test Data In);
- TDO (Test Data Out);
- TCK (Test Clock);
- TMS (Test Mode Select);
- TRST (Test Reset) (Optional);
The SoC equipped with JTAG master controller, performs
device programming on command or vector level. For example
a file in a standard SVF (Serial Vector Format) that contains
boundary scan vectors, can be used by sending each vector
to the JTAG interface and the JTAG controller will execute
the programming.
Initial version provides the system calls set for:
- SIR (Scan Instruction Register, IEEE 1149.1 Data Register scan);
- SDR (Scan Data Register, IEEE 1149.1 Instruction Register scan);
- RUNTEST (Forces the IEEE 1149.1 bus to a run state for a specified
number of clocks.
SoC which are not equipped with JTAG master interface, can be built
on top of JTAG core driver infrastructure, by applying bit-banging of
TDI, TDO, TCK and TMS pins within the hardware specific driver.
Oleksandr Shamray (4):
drivers: jtag: Add JTAG core driver
drivers: jtag: Add Aspeed SoC 24xx and 25xx families JTAG master
driver
Documentation: jtag: Add bindings for Aspeed SoC 24xx and 25xx
families JTAG master driver
Documentation: jtag: Add ABI documentation
Documentation/ABI/testing/jtag-dev | 27 +
.../devicetree/bindings/jtag/aspeed-jtag.txt | 18 +
Documentation/ioctl/ioctl-number.txt | 2 +
MAINTAINERS | 10 +
drivers/Kconfig | 2 +
drivers/Makefile | 1 +
drivers/jtag/Kconfig | 29 +
drivers/jtag/Makefile | 2 +
drivers/jtag/jtag-aspeed.c | 783 ++++++++++++++++++++
drivers/jtag/jtag.c | 288 +++++++
include/linux/jtag.h | 45 ++
include/uapi/linux/jtag.h | 104 +++
12 files changed, 1311 insertions(+), 0 deletions(-)
create mode 100644 Documentation/ABI/testing/jtag-dev
create mode 100644 Documentation/devicetree/bindings/jtag/aspeed-jtag.txt
create mode 100644 drivers/jtag/Kconfig
create mode 100644 drivers/jtag/Makefile
create mode 100644 drivers/jtag/jtag-aspeed.c
create mode 100644 drivers/jtag/jtag.c
create mode 100644 include/linux/jtag.h
create mode 100644 include/uapi/linux/jtag.h
^ permalink raw reply
* Re: [PATCH v2 5/7] dt-bindings: i3c: Document core bindings
From: Geert Uytterhoeven @ 2017-12-14 16:24 UTC (permalink / raw)
To: Boris Brezillon
Cc: Wolfram Sang, Linux I2C, Jonathan Corbet, linux-doc,
Greg Kroah-Hartman, Arnd Bergmann, Przemyslaw Sroka,
Arkadiusz Golec, Alan Douglas, Bartosz Folta, Damian Kos,
Alicja Jurasik-Urbaniak, Cyprian Wronka, Suresh Punnoose,
Thomas Petazzoni, Nishanth Menon, Rob Herring, Pawel Moll,
Mark Rutland, Ian Campbell
In-Reply-To: <20171214151610.19153-6-boris.brezillon@free-electrons.com>
Hi Boris,
On Thu, Dec 14, 2017 at 4:16 PM, Boris Brezillon
<boris.brezillon@free-electrons.com> wrote:
> A new I3C subsystem has been added and a generic description has been
> created to represent the I3C bus and the devices connected on it.
>
> Document this generic representation.
>
> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Thanks for your patch!
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i3c/i3c.txt
> @@ -0,0 +1,128 @@
> +Generic device tree bindings for I3C busses
> +===========================================
> +
> +This document describes generic bindings that should be used to describe I3C
> +busses in a device tree.
> +
> +Required properties
> +-------------------
> +
> +- #address-cells - should be <1>. Read more about addresses below.
> +- #size-cells - should be <0>.
> +- compatible - name of I3C bus controller following generic names
> + recommended practice.
> +
> +For other required properties e.g. to describe register sets,
> +clocks, etc. check the binding documentation of the specific driver.
> +
> +Optional properties
> +-------------------
> +
> +These properties may not be supported by all I3C master drivers. Each I3C
> +master bindings should specify which of them are supported.
> +
> +- i3c-scl-frequency: frequency (in Hz) of the SCL signal used for I3C
> + transfers. When undefined the core set it to 12.5MHz.
sets
> +
> +- i2c-scl-frequency: frequency (in Hz) of the SCL signal used for I2C
> + transfers. When undefined, the core looks at LVR values
LVR (Legacy I2C Virtual Register)
> + of I2C devices described in the device tree to determine
> + the maximum I2C frequency.
> +
> +I2C devices
> +===========
> +
> +Each I2C device connected to the bus should be described in a subnode with
> +the following properties:
This colon looks a bit funny here, as below is a sentence, not a list.
> +
> +All properties described in Documentation/devicetree/bindings/i2c/i2c.txt are
> +valid here.
Perhaps rewrite as:
Each I2C device connected to the bus should be described in a subnode with
properties. All properties described in
Documentation/devicetree/bindings/i2c/i2c.txt are valid here, but several
new properties have been added.
> +
> +New required properties:
> +------------------------
> +- i3c-lvr: 32 bits integer property (only the lowest 8 bits are meaningful)
> + describing device capabilities as described in the I3C
> + specification.
> +
> + bit[31:8]: unused
> + bit[7:5]: I2C device index. Possible values
> + * 0: I2C device has a 50 ns spike filter
> + * 1: I2C device does not have a 50 ns spike filter but supports high
> + frequency on SCL
> + * 2: I2C device does not have a 50 ns spike filter and is not
> + tolerant to high frequencies
> + * 3-7: reserved
> +
> + bit[4]: tell whether the device operates in FM or FM+ mode
> + * 0: FM+ mode
> + * 1: FM mode
As this is the only reference to "FM", perhaps clarify the acronym, like you
do for DAA below.
> +
> + bit[3:0]: device type
> + * 0-15: reserved
> +
> +I3C devices
> +===========
> +
> +All I3C devices are supposed to support DAA (Dynamic Address Assignment), and
> +are thus discoverable. So, by default, I3C devices do not have to be described
> +in the device tree.
> +This being said, one might want to attach extra resources to these devices,
> +and those resources may have to be described in the device tree, which in turn
> +means we have to describe I3C devices.
> +
> +Another use case for describing an I3C device in the device tree is when this
> +I3C device has a static address and we want to assign it a specific dynamic
> +address before the DAA takes place (so that other devices on the bus can't
> +take this dynamic address).
> +
> +Required properties
> +-------------------
> +- i3c-pid: PID (Provisional ID). 64-bit property which is used to match a
> + device discovered during DAA with its device tree definition. The
> + PID is supposed to be unique on a given bus, which guarantees a 1:1
> + match. This property becomes optional if a reg property is defined,
> + meaning that the device has a static address.
> +
> +Optional properties
> +-------------------
> +- reg: static address. Only valid is the device has a static address.
if
--
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* Re: [PATCH 1/1] dt-bindings: arm: document supported STM32 SoC family
From: Ludovic BARRE @ 2017-12-14 16:16 UTC (permalink / raw)
To: Rob Herring
Cc: Mark Rutland, devicetree@vger.kernel.org, Alexandre Torgue,
linux-kernel@vger.kernel.org, Maxime Coquelin, Gwenael Treuveur,
linux-arm-kernel@lists.infradead.org
In-Reply-To: <CAL_JsqJ8+NrOOpg1VcC8ZVVtm3tFTL2qvj8GSkrPU91CWDqzDA@mail.gmail.com>
On 12/14/2017 04:05 PM, Rob Herring wrote:
> On Wed, Dec 13, 2017 at 2:40 AM, Ludovic BARRE <ludovic.barre@st.com> wrote:
>> hi Rob
>>
>> Today there was no bindings documentation for STM32 SoC
>> already upstreamed. This patch adds initial list of STM32
>> existing in kernel.
>> The next serie adds just new soc and one compatible on STM32 list.
>
> Yes, and that series will go thru arm-soc tree so this patch needs to too.
You are right, to avoid merge conflict.
I will included this patch in my series
on "ARM: stm32: add initial STM32MPU support"
This patch can be abandoned.
>
>> So, I think you could apply this patch.
>
> If your series is not going into 4.16, then I can take this one.
>
> Rob
>
^ permalink raw reply
* [PATCH v12 3/3] arm64:dts:hisilicon Disable hisilicon smmu node on hip06/hip07
From: Shameer Kolothum @ 2017-12-14 16:09 UTC (permalink / raw)
To: lorenzo.pieralisi, robin.murphy, marc.zyngier, will.deacon
Cc: joro, john.garry, xuwei5, guohanjun, iommu, linux-arm-kernel,
linux-acpi, devicetree, linuxarm, Shameer Kolothum
In-Reply-To: <20171214160957.13716-1-shameerali.kolothum.thodi@huawei.com>
The HiSilicon erratum 161010801 describes the limitation of
HiSilicon platforms hip06/hip07 to support the SMMUv3 mappings
for MSI transactions.
PCIe controller on these platforms has to differentiate the
MSI payload against other DMA payload and has to modify the
MSI payload. This makes it difficult for these platforms to
have SMMU translation for MSI. In order to workaround this,
ARM SMMUv3 driver requires a quirk to treat the MSI regions
separately. Such a quirk is currently missing for DT based
systems and therefore we need to explicitly disable the
hip06/hip07 smmu entries in dts.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
---
arch/arm64/boot/dts/hisilicon/hip06.dtsi | 56 ++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/hisilicon/hip07.dtsi | 25 ++++++++++++++
2 files changed, 81 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
index a049b64..35202eb 100644
--- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
@@ -291,6 +291,13 @@
#interrupt-cells = <2>;
num-pins = <128>;
};
+
+ mbigen_pcie0: intc_pcie0 {
+ msi-parent = <&its_dsa 0x40085>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ num-pins = <10>;
+ };
};
mbigen_dsa@c0080000 {
@@ -312,6 +319,31 @@
};
};
+ /**
+ * HiSilicon erratum 161010801: This describes the limitation
+ * of HiSilicon platforms hip06/hip07 to support the SMMUv3
+ * mappings for PCIe MSI transactions.
+ * PCIe controller on these platforms has to differentiate the
+ * MSI payload against other DMA payload and has to modify the
+ * MSI payload. This makes it difficult for these platforms to
+ * have a SMMU translation for MSI. In order to workaround this,
+ * ARM SMMUv3 driver requires a quirk to treat the MSI regions
+ * separately. Such a quirk is currently missing for DT based
+ * systems. Hence please make sure that the smmu pcie node on
+ * hip06 is disabled as this will break the PCIe functionality
+ * when iommu-map entry is used along with the PCIe node.
+ * Refer:https://www.spinics.net/lists/arm-kernel/msg602812.html
+ */
+ smmu0: smmu_pcie {
+ compatible = "arm,smmu-v3";
+ reg = <0x0 0xa0040000 0x0 0x20000>;
+ #iommu-cells = <1>;
+ dma-coherent;
+ smmu-cb-memtype = <0x0 0x1>;
+ hisilicon,broken-prefetch-cmd;
+ status = "disabled";
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
@@ -676,6 +708,30 @@
<637 1>,<638 1>,<639 1>;
status = "disabled";
};
+
+ pcie0: pcie@a0090000 {
+ compatible = "hisilicon,hip06-pcie-ecam";
+ reg = <0 0xb0000000 0 0x2000000>,
+ <0 0xa0090000 0 0x10000>;
+ bus-range = <0 31>;
+ msi-map = <0x0000 &its_dsa 0x0000 0x2000>;
+ msi-map-mask = <0xffff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ dma-coherent;
+ ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0
+ 0x5ff0000 0x01000000 0 0 0 0xb7ff0000
+ 0 0x10000>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0x0 0 0 1 &mbigen_pcie0 650 4
+ 0x0 0 0 2 &mbigen_pcie0 650 4
+ 0x0 0 0 3 &mbigen_pcie0 650 4
+ 0x0 0 0 4 &mbigen_pcie0 650 4>;
+ status = "disabled";
+ };
+
};
};
diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi
index 2c01a21..3e80bf3 100644
--- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi
@@ -1083,6 +1083,31 @@
};
};
+ /**
+ * HiSilicon erratum 161010801: This describes the limitation
+ * of HiSilicon platforms hip06/hip07 to support the SMMUv3
+ * mappings for PCIe MSI transactions.
+ * PCIe controller on these platforms has to differentiate the
+ * MSI payload against other DMA payload and has to modify the
+ * MSI payload. This makes it difficult for these platforms to
+ * have a SMMU translation for MSI. In order to workaround this,
+ * ARM SMMUv3 driver requires a quirk to treat the MSI regions
+ * separately. Such a quirk is currently missing for DT based
+ * systems. Hence please make sure that the smmu pcie node on
+ * hip07 is disabled as this will break the PCIe functionality
+ * when iommu-map entry is used along with the PCIe node.
+ * Refer:https://www.spinics.net/lists/arm-kernel/msg602812.html
+ */
+ smmu0: smmu_pcie {
+ compatible = "arm,smmu-v3";
+ reg = <0x0 0xa0040000 0x0 0x20000>;
+ #iommu-cells = <1>;
+ dma-coherent;
+ smmu-cb-memtype = <0x0 0x1>;
+ hisilicon,broken-prefetch-cmd;
+ status = "disabled";
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <2>;
--
1.9.1
^ permalink raw reply related
* [PATCH v12 2/3] iommu/dma: Add HW MSI(GICv3 ITS) address regions reservation
From: Shameer Kolothum @ 2017-12-14 16:09 UTC (permalink / raw)
To: lorenzo.pieralisi-5wv7dgnIgG8, robin.murphy-5wv7dgnIgG8,
marc.zyngier-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8
Cc: joro-zLv9SwRftAIdnm+yROfE0A, john.garry-hv44wF8Li93QT0dZR+AlfA,
xuwei5-C8/M+/jPZTeaMJb+Lgu22Q, guohanjun-hv44wF8Li93QT0dZR+AlfA,
iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-acpi-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linuxarm-hv44wF8Li93QT0dZR+AlfA, Shameer Kolothum
In-Reply-To: <20171214160957.13716-1-shameerali.kolothum.thodi-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>
Modified iommu_dma_get_resv_regions() to include GICv3 ITS
region on ACPI based ARM platfiorms which may require HW MSI
reservations.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi-hv44wF8Li93QT0dZR+AlfA@public.gmane.org>
Reviewed-by: Robin Murphy <robin.murphy-5wv7dgnIgG8@public.gmane.org>
---
drivers/iommu/dma-iommu.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/iommu/dma-iommu.c b/drivers/iommu/dma-iommu.c
index 25914d3..f05f3cf 100644
--- a/drivers/iommu/dma-iommu.c
+++ b/drivers/iommu/dma-iommu.c
@@ -19,6 +19,7 @@
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
+#include <linux/acpi_iort.h>
#include <linux/device.h>
#include <linux/dma-iommu.h>
#include <linux/gfp.h>
@@ -167,13 +168,18 @@ void iommu_put_dma_cookie(struct iommu_domain *domain)
*
* IOMMU drivers can use this to implement their .get_resv_regions callback
* for general non-IOMMU-specific reservations. Currently, this covers host
- * bridge windows for PCI devices.
+ * bridge windows for PCI devices and GICv3 ITS region reservation on ACPI
+ * based ARM platforms that may require HW MSI reservation.
*/
void iommu_dma_get_resv_regions(struct device *dev, struct list_head *list)
{
struct pci_host_bridge *bridge;
struct resource_entry *window;
+ if (!is_of_node(dev->iommu_fwspec->iommu_fwnode) &&
+ iort_iommu_msi_get_resv_regions(dev, list) < 0)
+ return;
+
if (!dev_is_pci(dev))
return;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v12 1/3] ACPI/IORT: Add msi address regions reservation helper
From: Shameer Kolothum @ 2017-12-14 16:09 UTC (permalink / raw)
To: lorenzo.pieralisi, robin.murphy, marc.zyngier, will.deacon
Cc: joro, john.garry, xuwei5, guohanjun, iommu, linux-arm-kernel,
linux-acpi, devicetree, linuxarm, Shameer Kolothum
In-Reply-To: <20171214160957.13716-1-shameerali.kolothum.thodi@huawei.com>
On some platforms msi parent address regions have to be excluded from
normal IOVA allocation in that they are detected and decoded in a HW
specific way by system components and so they cannot be considered normal
IOVA address space.
Add a helper function that retrieves ITS address regions - the msi
parent - through IORT device <-> ITS mappings and reserves it so that
these regions will not be translated by IOMMU and will be excluded from
IOVA allocations. The function checks for the smmu model number and
only applies the msi reservation if the platform requires it.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
---
drivers/acpi/arm64/iort.c | 111 +++++++++++++++++++++++++++++++++++++--
drivers/irqchip/irq-gic-v3-its.c | 3 +-
include/linux/acpi_iort.h | 7 ++-
3 files changed, 116 insertions(+), 5 deletions(-)
diff --git a/drivers/acpi/arm64/iort.c b/drivers/acpi/arm64/iort.c
index 95255ec..e2f7bdd 100644
--- a/drivers/acpi/arm64/iort.c
+++ b/drivers/acpi/arm64/iort.c
@@ -39,6 +39,7 @@
struct iort_its_msi_chip {
struct list_head list;
struct fwnode_handle *fw_node;
+ phys_addr_t base_addr;
u32 translation_id;
};
@@ -161,14 +162,16 @@ typedef acpi_status (*iort_find_node_callback)
static DEFINE_SPINLOCK(iort_msi_chip_lock);
/**
- * iort_register_domain_token() - register domain token and related ITS ID
- * to the list from where we can get it back later on.
+ * iort_register_domain_token() - register domain token along with related
+ * ITS ID and base address to the list from where we can get it back later on.
* @trans_id: ITS ID.
+ * @base: ITS base address.
* @fw_node: Domain token.
*
* Returns: 0 on success, -ENOMEM if no memory when allocating list element
*/
-int iort_register_domain_token(int trans_id, struct fwnode_handle *fw_node)
+int iort_register_domain_token(int trans_id, phys_addr_t base,
+ struct fwnode_handle *fw_node)
{
struct iort_its_msi_chip *its_msi_chip;
@@ -178,6 +181,7 @@ int iort_register_domain_token(int trans_id, struct fwnode_handle *fw_node)
its_msi_chip->fw_node = fw_node;
its_msi_chip->translation_id = trans_id;
+ its_msi_chip->base_addr = base;
spin_lock(&iort_msi_chip_lock);
list_add(&its_msi_chip->list, &iort_msi_chip_list);
@@ -581,6 +585,24 @@ int iort_pmsi_get_dev_id(struct device *dev, u32 *dev_id)
return -ENODEV;
}
+static int __maybe_unused iort_find_its_base(u32 its_id, phys_addr_t *base)
+{
+ struct iort_its_msi_chip *its_msi_chip;
+ int ret = -ENODEV;
+
+ spin_lock(&iort_msi_chip_lock);
+ list_for_each_entry(its_msi_chip, &iort_msi_chip_list, list) {
+ if (its_msi_chip->translation_id == its_id) {
+ *base = its_msi_chip->base_addr;
+ ret = 0;
+ break;
+ }
+ }
+ spin_unlock(&iort_msi_chip_lock);
+
+ return ret;
+}
+
/**
* iort_dev_find_its_id() - Find the ITS identifier for a device
* @dev: The device.
@@ -766,6 +788,24 @@ static inline bool iort_iommu_driver_enabled(u8 type)
}
#ifdef CONFIG_IOMMU_API
+static struct acpi_iort_node *iort_get_msi_resv_iommu(struct device *dev)
+{
+ struct acpi_iort_node *iommu;
+ struct iommu_fwspec *fwspec = dev->iommu_fwspec;
+
+ iommu = iort_get_iort_node(fwspec->iommu_fwnode);
+
+ if (iommu && (iommu->type == ACPI_IORT_NODE_SMMU_V3)) {
+ struct acpi_iort_smmu_v3 *smmu;
+
+ smmu = (struct acpi_iort_smmu_v3 *)iommu->node_data;
+ if (smmu->model == ACPI_IORT_SMMU_V3_HISILICON_HI161X)
+ return iommu;
+ }
+
+ return NULL;
+}
+
static inline const struct iommu_ops *iort_fwspec_iommu_ops(
struct iommu_fwspec *fwspec)
{
@@ -782,6 +822,69 @@ static inline int iort_add_device_replay(const struct iommu_ops *ops,
return err;
}
+
+/**
+ * iort_iommu_msi_get_resv_regions - Reserved region driver helper
+ * @dev: Device from iommu_get_resv_regions()
+ * @head: Reserved region list from iommu_get_resv_regions()
+ *
+ * Returns: Number of msi reserved regions on success (0 if platform
+ * doesn't require the reservation or no associated msi regions),
+ * appropriate error value otherwise. The ITS interrupt translation
+ * spaces (ITS_base + SZ_64K, SZ_64K) associated with the device
+ * are the msi reserved regions.
+ */
+int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head)
+{
+ struct acpi_iort_its_group *its;
+ struct acpi_iort_node *iommu_node, *its_node = NULL;
+ int i, resv = 0;
+
+ iommu_node = iort_get_msi_resv_iommu(dev);
+ if (!iommu_node)
+ return 0;
+
+ /*
+ * Current logic to reserve ITS regions relies on HW topologies
+ * where a given PCI or named component maps its IDs to only one
+ * ITS group; if a PCI or named component can map its IDs to
+ * different ITS groups through IORT mappings this function has
+ * to be reworked to ensure we reserve regions for all ITS groups
+ * a given PCI or named component may map IDs to.
+ */
+
+ for (i = 0; i < dev->iommu_fwspec->num_ids; i++) {
+ its_node = iort_node_map_id(iommu_node,
+ dev->iommu_fwspec->ids[i],
+ NULL, IORT_MSI_TYPE);
+ if (its_node)
+ break;
+ }
+
+ if (!its_node)
+ return 0;
+
+ /* Move to ITS specific data */
+ its = (struct acpi_iort_its_group *)its_node->node_data;
+
+ for (i = 0; i < its->its_count; i++) {
+ phys_addr_t base;
+
+ if (!iort_find_its_base(its->identifiers[i], &base)) {
+ int prot = IOMMU_WRITE | IOMMU_NOEXEC | IOMMU_MMIO;
+ struct iommu_resv_region *region;
+
+ region = iommu_alloc_resv_region(base + SZ_64K, SZ_64K,
+ prot, IOMMU_RESV_MSI);
+ if (region) {
+ list_add_tail(®ion->list, head);
+ resv++;
+ }
+ }
+ }
+
+ return (resv == its->its_count) ? resv : -ENODEV;
+}
#else
static inline const struct iommu_ops *iort_fwspec_iommu_ops(
struct iommu_fwspec *fwspec)
@@ -789,6 +892,8 @@ static inline const struct iommu_ops *iort_fwspec_iommu_ops(
static inline int iort_add_device_replay(const struct iommu_ops *ops,
struct device *dev)
{ return 0; }
+int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head)
+{ return 0; }
#endif
static int iort_iommu_xlate(struct device *dev, struct acpi_iort_node *node,
diff --git a/drivers/irqchip/irq-gic-v3-its.c b/drivers/irqchip/irq-gic-v3-its.c
index 4039e64..d4cff12 100644
--- a/drivers/irqchip/irq-gic-v3-its.c
+++ b/drivers/irqchip/irq-gic-v3-its.c
@@ -3450,7 +3450,8 @@ static int __init gic_acpi_parse_madt_its(struct acpi_subtable_header *header,
return -ENOMEM;
}
- err = iort_register_domain_token(its_entry->translation_id, dom_handle);
+ err = iort_register_domain_token(its_entry->translation_id, res.start,
+ dom_handle);
if (err) {
pr_err("ITS@%pa: Unable to register GICv3 ITS domain token (ITS ID %d) to IORT\n",
&res.start, its_entry->translation_id);
diff --git a/include/linux/acpi_iort.h b/include/linux/acpi_iort.h
index 2f7a292..38cd77b 100644
--- a/include/linux/acpi_iort.h
+++ b/include/linux/acpi_iort.h
@@ -26,7 +26,8 @@
#define IORT_IRQ_MASK(irq) (irq & 0xffffffffULL)
#define IORT_IRQ_TRIGGER_MASK(irq) ((irq >> 32) & 0xffffffffULL)
-int iort_register_domain_token(int trans_id, struct fwnode_handle *fw_node);
+int iort_register_domain_token(int trans_id, phys_addr_t base,
+ struct fwnode_handle *fw_node);
void iort_deregister_domain_token(int trans_id);
struct fwnode_handle *iort_find_domain_token(int trans_id);
#ifdef CONFIG_ACPI_IORT
@@ -38,6 +39,7 @@
/* IOMMU interface */
void iort_dma_setup(struct device *dev, u64 *dma_addr, u64 *size);
const struct iommu_ops *iort_iommu_configure(struct device *dev);
+int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head);
#else
static inline void acpi_iort_init(void) { }
static inline u32 iort_msi_map_rid(struct device *dev, u32 req_id)
@@ -52,6 +54,9 @@ static inline void iort_dma_setup(struct device *dev, u64 *dma_addr,
static inline const struct iommu_ops *iort_iommu_configure(
struct device *dev)
{ return NULL; }
+static inline
+int iort_iommu_msi_get_resv_regions(struct device *dev, struct list_head *head)
+{ return 0; }
#endif
#endif /* __ACPI_IORT_H__ */
--
1.9.1
^ permalink raw reply related
* [PATCH v12 0/3] iommu/smmu-v3: Workaround for hisilicon 161010801 erratum(reserve HW MSI)
From: Shameer Kolothum @ 2017-12-14 16:09 UTC (permalink / raw)
To: lorenzo.pieralisi-5wv7dgnIgG8, robin.murphy-5wv7dgnIgG8,
marc.zyngier-5wv7dgnIgG8, will.deacon-5wv7dgnIgG8
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linuxarm-hv44wF8Li93QT0dZR+AlfA, xuwei5-C8/M+/jPZTeaMJb+Lgu22Q,
linux-acpi-u79uwXL29TY76Z2rM5mHXA,
iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA,
Shameer Kolothum, guohanjun-hv44wF8Li93QT0dZR+AlfA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On certain HiSilicon platforms (hip06/hip07) the GIC ITS and PCIe RC
deviates from the standard implementation and this breaks PCIe MSI
functionality when SMMU is enabled.
The HiSilicon erratum 161010801 describes this limitation of certain
HiSilicon platforms to support the SMMU mappings for MSI transactions.
On these platforms GICv3 ITS translator is presented with the deviceID
by extending the MSI payload data to 64 bits to include the deviceID.
Hence, the PCIe controller on this platforms has to differentiate the MSI
payload against other DMA payload and has to modify the MSI payload.
This basically makes it difficult for this platforms to have a SMMU
translation for MSI.
This patch implements an ACPI based quirk to reserve the hw msi regions
in the smmu-v3 driver which means these address regions will not be
translated and will be excluded from iova allocations.
To implement this quirk, the following changes are incorporated:
1. Added a generic helper function to IORT code to retrieve and reserve
the associated ITS base address from a device IORT node. The function
has a check for smmu model to determine whether the platform requires
the HW MSI reservation or not.
2. Added smmu node entries and explicitly disabled them in hip06/hip07
dts files so that users are warned about the non-DT support for this
erratum.
Changelog:
v11--> v12
-Thanks to Lorenzo, Fixed !CONFIG_IOMMU_API compile error(patch #1).
v10 --> v11
-Addressed comments from Lorenzo(patch#1)
-Added Robin's Reviewed-by to patch #2
v9 --> v10
Addressed comments:
-Moved smmu model check to iort helper function to selectively apply
the msi reservation which will make the fn call generic from iommu-dma.
-Removed PCI blacklisting patch, instead added smmu nodes(disabled)
with comments to hip06/hip07 dts file.
v8 --> v9
-Thanks to Marc, fixed IORT helper function to reserve the ITS
translater region only.
-Removed the DT support for MSI reservation and blacklisted
HiSilicon PCIe controllers on DT based systems when SMMUv3 is
enabled.
v7 --> v8
Addressed comments from Rob and Lorenzo:
-Modified to use DT compatible string for errata.
-Changed logic to retrieve the msi-parent for DT case.
v6 --> v7
Addressed request from Will to add DT support for the erratum:
- added bt binding
- add of_iommu_msi_get_resv_regions()
New arm64 silicon errata entry
Rename iort_iommu_{its->msi}_get_resv_regions
v5 --> v6
Addressed comments from Robin and Lorenzo:
-No change to patch#1 .
-Reverted v5 patch#2 as this might break the platforms where this quirk
is not applicable. Provided a generic function in iommu code and added
back the quirk implementation in SMMU v3 driver(patch#3)
v4 --> v5
Addressed comments from Robin and Lorenzo:
-Added a comment to make it clear that, for now, only straightforward
HW topologies are handled while reserving ITS regions(patch #1).
v3 --> v4
Rebased on 4.13-rc1.
Addressed comments from Robin, Will and Lorenzo:
-As suggested by Robin, moved the ITS msi reservation into
iommu_dma_get_resv_regions().
-Added its_count != resv region failure case(patch #1).
v2 --> v3
Addressed comments from Lorenzo and Robin:
-Removed dev_is_pci() check in smmuV3 driver.
-Don't treat device not having an ITS mapping as an error in
iort helper function.
v1 --> v2
-patch 2/2: Invoke iort helper fn based on fwnode type(acpi).
RFCv2 -->PATCH
-Incorporated Lorenzo's review comments.
RFC v1 --> RFC v2
Based on Robin's review comments,
-Removed the generic erratum framework.
-Using IORT/MADT tables to retrieve the ITS base addr instead
of vendor specific CSRT table.
Shameer Kolothum (3):
ACPI/IORT: Add msi address regions reservation helper
iommu/dma: Add HW MSI(GICv3 ITS) address regions reservation
arm64:dts:hisilicon Disable hisilicon smmu node on hip06/hip07
arch/arm64/boot/dts/hisilicon/hip06.dtsi | 56 ++++++++++++++++
arch/arm64/boot/dts/hisilicon/hip07.dtsi | 25 +++++++
drivers/acpi/arm64/iort.c | 111 ++++++++++++++++++++++++++++++-
drivers/iommu/dma-iommu.c | 8 ++-
drivers/irqchip/irq-gic-v3-its.c | 3 +-
include/linux/acpi_iort.h | 7 +-
6 files changed, 204 insertions(+), 6 deletions(-)
--
1.9.1
^ permalink raw reply
* Re: [PATCH v4 3/4] cpufreq: Add DVFS support for Armada 37xx
From: Viresh Kumar @ 2017-12-14 15:36 UTC (permalink / raw)
To: Gregory CLEMENT
Cc: Rafael J. Wysocki, linux-pm-u79uwXL29TY76Z2rM5mHXA, Jason Cooper,
Andrew Lunn, Sebastian Hesselbarth, Rob Herring,
devicetree-u79uwXL29TY76Z2rM5mHXA, Thomas Petazzoni,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r, Antoine Tenart,
Miquèl Raynal, Nadav Haklai, Victor Gu, Marcin Wojtas,
Wilson Ding, Hua Jing, Neta Zur Hershkovits, Evan Wang,
Andre Heider
In-Reply-To: <20171214150006.25438-4-gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
On 14-12-17, 16:00, Gregory CLEMENT wrote:
> This patch adds DVFS support for the Armada 37xx SoCs
>
> There are up to four CPU frequency loads for Armada 37xx controlled by
> the hardware.
>
> This driver associates the CPU load level to a frequency, then the
> hardware will switch while selecting a load level.
>
> The hardware also can associate a voltage for each level (AVS support)
> but it is not yet supported
>
> Tested-by: Andre Heider <a.heider-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> Acked-by: Viresh Kumar <viresh.kumar-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> ---
> drivers/cpufreq/Kconfig.arm | 7 +
> drivers/cpufreq/Makefile | 1 +
> drivers/cpufreq/armada-37xx-cpufreq.c | 241 ++++++++++++++++++++++++++++++++++
> 3 files changed, 249 insertions(+)
> create mode 100644 drivers/cpufreq/armada-37xx-cpufreq.c
Thanks for taking care of very minor review comments I had. All the
patches look good now to me :)
--
viresh
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* Re: [v2, 1/2] dt: bindings: add new dt entry for ath10k calibration variant
From: Kalle Valo @ 2017-12-14 15:28 UTC (permalink / raw)
Cc: ath10k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
mark.rutland-5wv7dgnIgG8,
ext.waldemar.rymarkiewicz-++hxYGjEMp0AvxtiuMwx3w,
kvalo-sgV2jX0FEOL9JmXXK+q4OQ, Sven Eckelmann
In-Reply-To: <20171208103742.3181-2-sven.eckelmann-lv6y7wLVQPlWk0Htik3J/w@public.gmane.org>
Sven Eckelmann <sven.eckelmann-lv6y7wLVQPlWk0Htik3J/w@public.gmane.org> wrote:
> The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct
> board data file on QCA4019 based devices. Multiple different boards share
> the same values. Only the original reference designs can currently be
> identified and loaded from the board-2.bin. But these will not result in
> the correct calibration data when combined with the pre-calibration data
> from the device.
>
> An additional "variant" information has to be provided (via SMBIOS or DT)
> to select the correct board data for a design which was modified by an ODM.
>
> Signed-off-by: Sven Eckelmann <sven.eckelmann-lv6y7wLVQPlWk0Htik3J/w@public.gmane.org>
> Signed-off-by: Kalle Valo <kvalo-A+ZNKFmMK5xy9aJCnZT0Uw@public.gmane.org>
2 patches applied to ath-next branch of ath.git, thanks.
40fb0eab30ba dt: bindings: add new dt entry for ath10k calibration variant
d06f26c5c8a4 ath10k: search DT for qcom,ath10k-calibration-variant
--
https://patchwork.kernel.org/patch/10102249/
https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox