* [PATCH v5 13/15] clk: qcom: Add safe switch hook for krait mux clocks
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
mturquette-rdvid1DuHRBWk0Htik3J/w, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, andy.gross-QSEj5FYQhm4dnm+yROfE0A,
david.brown-QSEj5FYQhm4dnm+yROfE0A, rjw-LthD3rsA81gm4RdzfppkhA,
viresh.kumar-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-soc-u79uwXL29TY76Z2rM5mHXA, linux-pm-u79uwXL29TY76Z2rM5mHXA
Cc: sricharan-sgV2jX0FEOL9JmXXK+q4OQ
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
When the Hfplls are reprogrammed during the rate change,
the primary muxes which are sourced from the same hfpll
for higher frequencies, needs to be switched to the 'safe
secondary mux' as the parent for that small window. This
is done by registering a clk notifier for the muxes and
switching to the safe parent in the PRE_RATE_CHANGE notifier
and back to the original parent in the POST_RATE_CHANGE notifier.
Signed-off-by: Sricharan R <sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/clk/qcom/clk-krait.c | 2 ++
drivers/clk/qcom/clk-krait.h | 3 +++
drivers/clk/qcom/krait-cc.c | 56 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 61 insertions(+)
diff --git a/drivers/clk/qcom/clk-krait.c b/drivers/clk/qcom/clk-krait.c
index 361c701..f9744f1 100644
--- a/drivers/clk/qcom/clk-krait.c
+++ b/drivers/clk/qcom/clk-krait.c
@@ -50,6 +50,8 @@ static int krait_mux_set_parent(struct clk_hw *hw, u8 index)
if (__clk_is_enabled(hw->clk))
__krait_mux_set_sel(mux, sel);
+ mux->reparent = true;
+
return 0;
}
diff --git a/drivers/clk/qcom/clk-krait.h b/drivers/clk/qcom/clk-krait.h
index d5c9c60..6e2d4f4 100644
--- a/drivers/clk/qcom/clk-krait.h
+++ b/drivers/clk/qcom/clk-krait.h
@@ -13,6 +13,9 @@ struct krait_mux_clk {
u32 shift;
u32 en_mask;
bool lpl;
+ u8 safe_sel;
+ u8 old_index;
+ bool reparent;
struct clk_hw hw;
struct notifier_block clk_nb;
diff --git a/drivers/clk/qcom/krait-cc.c b/drivers/clk/qcom/krait-cc.c
index ee864fa..2d82c5f 100644
--- a/drivers/clk/qcom/krait-cc.c
+++ b/drivers/clk/qcom/krait-cc.c
@@ -26,6 +26,49 @@
0,
};
+/*
+ * Notifier function for switching the muxes to safe parent
+ * while the hfpll is getting reprogrammed.
+ */
+static int krait_notifier_cb(struct notifier_block *nb,
+ unsigned long event,
+ void *data)
+{
+ int ret = 0;
+ struct krait_mux_clk *mux = container_of(nb, struct krait_mux_clk,
+ clk_nb);
+ /* Switch to safe parent */
+ if (event == PRE_RATE_CHANGE) {
+ mux->old_index = krait_mux_clk_ops.get_parent(&mux->hw);
+ ret = krait_mux_clk_ops.set_parent(&mux->hw, mux->safe_sel);
+ mux->reparent = false;
+ /*
+ * By the time POST_RATE_CHANGE notifier is called,
+ * clk framework itself would have changed the parent for the new rate.
+ * Only otherwise, put back to the old parent.
+ */
+ } else if (event == POST_RATE_CHANGE) {
+ if (!mux->reparent)
+ ret = krait_mux_clk_ops.set_parent(&mux->hw,
+ mux->old_index);
+ }
+
+ return notifier_from_errno(ret);
+}
+
+static int krait_notifier_register(struct device *dev, struct clk *clk,
+ struct krait_mux_clk *mux)
+{
+ int ret = 0;
+
+ mux->clk_nb.notifier_call = krait_notifier_cb;
+ ret = clk_notifier_register(clk, &mux->clk_nb);
+ if (ret)
+ dev_err(dev, "failed to register clock notifier: %d\n", ret);
+
+ return ret;
+}
+
static int
krait_add_div(struct device *dev, int id, const char *s, unsigned int offset)
{
@@ -70,6 +113,7 @@
krait_add_sec_mux(struct device *dev, int id, const char *s,
unsigned int offset, bool unique_aux)
{
+ int ret;
struct krait_mux_clk *mux;
static const char *sec_mux_list[] = {
"acpu_aux",
@@ -93,6 +137,7 @@
mux->shift = 2;
mux->parent_map = sec_mux_map;
mux->hw.init = &init;
+ mux->safe_sel = 0;
init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
if (!init.name)
@@ -108,6 +153,11 @@
clk = devm_clk_register(dev, &mux->hw);
+ ret = krait_notifier_register(dev, clk, mux);
+ if (ret)
+ goto unique_aux;
+
+unique_aux:
if (unique_aux)
kfree(sec_mux_list[0]);
err_aux:
@@ -119,6 +169,7 @@
krait_add_pri_mux(struct device *dev, int id, const char *s,
unsigned int offset)
{
+ int ret;
struct krait_mux_clk *mux;
const char *p_names[3];
struct clk_init_data init = {
@@ -139,6 +190,7 @@
mux->lpl = id >= 0;
mux->parent_map = pri_mux_map;
mux->hw.init = &init;
+ mux->safe_sel = 2;
init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s);
if (!init.name)
@@ -164,6 +216,10 @@
clk = devm_clk_register(dev, &mux->hw);
+ ret = krait_notifier_register(dev, clk, mux);
+ if (ret)
+ goto err_p3;
+err_p3:
kfree(p_names[2]);
err_p2:
kfree(p_names[1]);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 12/15] devicetree: bindings: Document qcom,krait-cc
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
The Krait clock controller controls the krait CPU and the L2 clocks
consisting a primary mux and secondary mux. Add document for that.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../devicetree/bindings/clock/qcom,krait-cc.txt | 22 ++++++++++++++++++++++
1 file changed, 22 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
diff --git a/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
new file mode 100644
index 0000000..874138f
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
@@ -0,0 +1,22 @@
+Krait Clock Controller
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,krait-cc-v1"
+ "qcom,krait-cc-v2"
+
+- #clock-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 1
+
+Example:
+
+ kraitcc: clock-controller {
+ compatible = "qcom,krait-cc-v1";
+ #clock-cells = <1>;
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* Re: [PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture
From: Ludovic BARRE @ 2017-12-19 15:54 UTC (permalink / raw)
To: Arnd Bergmann
Cc: Russell King, Rob Herring, Linus Walleij, Maxime Coquelin,
Alexandre Torgue, Gerald Baeza, Linux ARM,
Linux Kernel Mailing List, DTML
In-Reply-To: <CAK8P3a3X1icDWmVng8w0Yd58nAcViJQ9oZc4xm-dEycVPe+5pg@mail.gmail.com>
On 12/19/2017 04:26 PM, Arnd Bergmann wrote:
> On Tue, Dec 19, 2017 at 3:43 PM, Ludovic BARRE <ludovic.barre@st.com> wrote:
>>
>>
>> On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
>>>
>>> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre@st.com>
>>> wrote:
>>>>
>>>> From: Ludovic Barre <ludovic.barre@st.com>
>>>>
>>>> This patch prepares the STM32 machine for the integration of Cortex-A
>>>> based microprocessor (MPU), on top of the existing Cortex-M
>>>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>>>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>>>> them. If a hardware block is specific to one family we can use either
>>>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>>>
>>>> Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
>>>
>>>
>>> Looks good overall. Two more small comments:
>>>
>>>
>>>>
>>>> +if ARCH_STM32
>>>> +
>>>> config MACH_STM32F429
>>>> - bool "STMicrolectronics STM32F429"
>>>> - depends on ARCH_STM32
>>>> + bool "STMicroelectronics STM32F429"
>>>> + depends on ARM_SINGLE_ARMV7M
>>>> default y
>>>
>>>
>>> Instead of the explicit dependency for each board, I'd leave the
>>> surrounding
>>> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
>>
>>
>> As you suggest, I follow mach-at91 example.
>> The point is on "depends on ARM_SINGLE_ARMV7M" ?
>> You prefer this way:
>> config MACH_STM32F429
>> bool "STMicroelectronics STM32F429" if ARM_SINGLE_ARMV7M
>> default y
>>
>
> No, that would be wrong, that way you would always enable
> MACH_STM32F429 when ARM_SINGLE_ARMV7M is turned
> off, which is exactly the wrong way round. What I meant is
>
> if ARCH_STM32
>
> if ARM_SINGLE_ARMV7M
>
> config MACH_STM32F429
> bool "STMicrolectronics STM32F429"
>
> config MACH_STM32...
> ...
>
> endif # ARMv7-M
>
> if ARCH_MULTI_V7
>
> config MACH_STM32...
> ...
>
> endif # ARMv7-A
>
> endif # STM32
>
> Arnd
>
Ok, it's clear :-)
^ permalink raw reply
* [PATCH v5 11/15] clk: qcom: Add Krait clock controller driver
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
The Krait CPU clocks are made up of a primary mux and secondary
mux for each CPU and the L2, controlled via cp15 accessors. For
Kraits within KPSSv1 each secondary mux accepts a different aux
source, but on KPSSv2 each secondary mux accepts the same aux
source.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 8 ++
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/krait-cc.c | 341 ++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 350 insertions(+)
create mode 100644 drivers/clk/qcom/krait-cc.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 17dcb88..de6b60d 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -222,6 +222,14 @@ config KPSS_XCC
if you want to support CPU frequency scaling on devices such
as MSM8960, APQ8064, etc.
+config KRAITCC
+ tristate "Krait Clock Controller"
+ depends on COMMON_CLK_QCOM && ARM
+ select KRAIT_CLOCKS
+ help
+ Support for the Krait CPU clocks on Qualcomm devices.
+ Say Y if you want to support CPU frequency scaling.
+
config KRAIT_CLOCKS
bool
select KRAIT_L2_ACCESSORS
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 7ad2302..6e6c700 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -39,3 +39,4 @@ obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
+obj-$(CONFIG_KRAITCC) += krait-cc.o
diff --git a/drivers/clk/qcom/krait-cc.c b/drivers/clk/qcom/krait-cc.c
new file mode 100644
index 0000000..ee864fa
--- /dev/null
+++ b/drivers/clk/qcom/krait-cc.c
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/slab.h>
+
+#include "clk-krait.h"
+
+static unsigned int sec_mux_map[] = {
+ 2,
+ 0,
+};
+
+static unsigned int pri_mux_map[] = {
+ 1,
+ 2,
+ 0,
+};
+
+static int
+krait_add_div(struct device *dev, int id, const char *s, unsigned int offset)
+{
+ struct krait_div2_clk *div;
+ struct clk_init_data init = {
+ .num_parents = 1,
+ .ops = &krait_div2_clk_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ };
+ const char *p_names[1];
+ struct clk *clk;
+
+ div = devm_kzalloc(dev, sizeof(*div), GFP_KERNEL);
+ if (!div)
+ return -ENOMEM;
+
+ div->width = 2;
+ div->shift = 6;
+ div->lpl = id >= 0;
+ div->offset = offset;
+ div->hw.init = &init;
+
+ init.name = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
+ if (!init.name)
+ return -ENOMEM;
+
+ init.parent_names = p_names;
+ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
+ if (!p_names[0]) {
+ kfree(init.name);
+ return -ENOMEM;
+ }
+
+ clk = devm_clk_register(dev, &div->hw);
+ kfree(p_names[0]);
+ kfree(init.name);
+
+ return PTR_ERR_OR_ZERO(clk);
+}
+
+static int
+krait_add_sec_mux(struct device *dev, int id, const char *s,
+ unsigned int offset, bool unique_aux)
+{
+ struct krait_mux_clk *mux;
+ static const char *sec_mux_list[] = {
+ "acpu_aux",
+ "qsb",
+ };
+ struct clk_init_data init = {
+ .parent_names = sec_mux_list,
+ .num_parents = ARRAY_SIZE(sec_mux_list),
+ .ops = &krait_mux_clk_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ };
+ struct clk *clk;
+
+ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
+ if (!mux)
+ return -ENOMEM;
+
+ mux->offset = offset;
+ mux->lpl = id >= 0;
+ mux->mask = 0x3;
+ mux->shift = 2;
+ mux->parent_map = sec_mux_map;
+ mux->hw.init = &init;
+
+ init.name = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
+ if (!init.name)
+ return -ENOMEM;
+
+ if (unique_aux) {
+ sec_mux_list[0] = kasprintf(GFP_KERNEL, "acpu%s_aux", s);
+ if (!sec_mux_list[0]) {
+ clk = ERR_PTR(-ENOMEM);
+ goto err_aux;
+ }
+ }
+
+ clk = devm_clk_register(dev, &mux->hw);
+
+ if (unique_aux)
+ kfree(sec_mux_list[0]);
+err_aux:
+ kfree(init.name);
+ return PTR_ERR_OR_ZERO(clk);
+}
+
+static struct clk *
+krait_add_pri_mux(struct device *dev, int id, const char *s,
+ unsigned int offset)
+{
+ struct krait_mux_clk *mux;
+ const char *p_names[3];
+ struct clk_init_data init = {
+ .parent_names = p_names,
+ .num_parents = ARRAY_SIZE(p_names),
+ .ops = &krait_mux_clk_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ };
+ struct clk *clk;
+
+ mux = devm_kzalloc(dev, sizeof(*mux), GFP_KERNEL);
+ if (!mux)
+ return ERR_PTR(-ENOMEM);
+
+ mux->mask = 0x3;
+ mux->shift = 0;
+ mux->offset = offset;
+ mux->lpl = id >= 0;
+ mux->parent_map = pri_mux_map;
+ mux->hw.init = &init;
+
+ init.name = kasprintf(GFP_KERNEL, "krait%s_pri_mux", s);
+ if (!init.name)
+ return ERR_PTR(-ENOMEM);
+
+ p_names[0] = kasprintf(GFP_KERNEL, "hfpll%s", s);
+ if (!p_names[0]) {
+ clk = ERR_PTR(-ENOMEM);
+ goto err_p0;
+ }
+
+ p_names[1] = kasprintf(GFP_KERNEL, "hfpll%s_div", s);
+ if (!p_names[1]) {
+ clk = ERR_PTR(-ENOMEM);
+ goto err_p1;
+ }
+
+ p_names[2] = kasprintf(GFP_KERNEL, "krait%s_sec_mux", s);
+ if (!p_names[2]) {
+ clk = ERR_PTR(-ENOMEM);
+ goto err_p2;
+ }
+
+ clk = devm_clk_register(dev, &mux->hw);
+
+ kfree(p_names[2]);
+err_p2:
+ kfree(p_names[1]);
+err_p1:
+ kfree(p_names[0]);
+err_p0:
+ kfree(init.name);
+ return clk;
+}
+
+/* id < 0 for L2, otherwise id == physical CPU number */
+static struct clk *krait_add_clks(struct device *dev, int id, bool unique_aux)
+{
+ int ret;
+ unsigned int offset;
+ void *p = NULL;
+ const char *s;
+ struct clk *clk;
+
+ if (id >= 0) {
+ offset = 0x4501 + (0x1000 * id);
+ s = p = kasprintf(GFP_KERNEL, "%d", id);
+ if (!s)
+ return ERR_PTR(-ENOMEM);
+ } else {
+ offset = 0x500;
+ s = "_l2";
+ }
+
+ ret = krait_add_div(dev, id, s, offset);
+ if (ret) {
+ clk = ERR_PTR(ret);
+ goto err;
+ }
+
+ ret = krait_add_sec_mux(dev, id, s, offset, unique_aux);
+ if (ret) {
+ clk = ERR_PTR(ret);
+ goto err;
+ }
+
+ clk = krait_add_pri_mux(dev, id, s, offset);
+err:
+ kfree(p);
+ return clk;
+}
+
+static struct clk *krait_of_get(struct of_phandle_args *clkspec, void *data)
+{
+ unsigned int idx = clkspec->args[0];
+ struct clk **clks = data;
+
+ if (idx >= 5) {
+ pr_err("%s: invalid clock index %d\n", __func__, idx);
+ return ERR_PTR(-EINVAL);
+ }
+
+ return clks[idx] ? : ERR_PTR(-ENODEV);
+}
+
+static const struct of_device_id krait_cc_match_table[] = {
+ { .compatible = "qcom,krait-cc-v1", (void *)1UL },
+ { .compatible = "qcom,krait-cc-v2" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, krait_cc_match_table);
+
+static int krait_cc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *id;
+ unsigned long cur_rate, aux_rate;
+ int cpu;
+ struct clk *clk;
+ struct clk **clks;
+ struct clk *l2_pri_mux_clk;
+
+ id = of_match_device(krait_cc_match_table, dev);
+ if (!id)
+ return -ENODEV;
+
+ /* Rate is 1 because 0 causes problems for __clk_mux_determine_rate */
+ clk = clk_register_fixed_rate(dev, "qsb", NULL, 0, 1);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ if (!id->data) {
+ clk = clk_register_fixed_factor(dev, "acpu_aux",
+ "gpll0_vote", 0, 1, 2);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ }
+
+ /* Krait configurations have at most 4 CPUs and one L2 */
+ clks = devm_kcalloc(dev, 5, sizeof(*clks), GFP_KERNEL);
+ if (!clks)
+ return -ENOMEM;
+
+ for_each_possible_cpu(cpu) {
+ clk = krait_add_clks(dev, cpu, id->data);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ clks[cpu] = clk;
+ }
+
+ l2_pri_mux_clk = krait_add_clks(dev, -1, id->data);
+ if (IS_ERR(l2_pri_mux_clk))
+ return PTR_ERR(l2_pri_mux_clk);
+ clks[4] = l2_pri_mux_clk;
+
+ /*
+ * We don't want the CPU or L2 clocks to be turned off at late init
+ * if CPUFREQ or HOTPLUG configs are disabled. So, bump up the
+ * refcount of these clocks. Any cpufreq/hotplug manager can assume
+ * that the clocks have already been prepared and enabled by the time
+ * they take over.
+ */
+ for_each_online_cpu(cpu) {
+ clk_prepare_enable(l2_pri_mux_clk);
+ WARN(clk_prepare_enable(clks[cpu]),
+ "Unable to turn on CPU%d clock", cpu);
+ }
+
+ /*
+ * Force reinit of HFPLLs and muxes to overwrite any potential
+ * incorrect configuration of HFPLLs and muxes by the bootloader.
+ * While at it, also make sure the cores are running at known rates
+ * and print the current rate.
+ *
+ * The clocks are set to aux clock rate first to make sure the
+ * secondary mux is not sourcing off of QSB. The rate is then set to
+ * two different rates to force a HFPLL reinit under all
+ * circumstances.
+ */
+ cur_rate = clk_get_rate(l2_pri_mux_clk);
+ aux_rate = 384000000;
+ if (cur_rate == 1) {
+ pr_info("L2 @ QSB rate. Forcing new rate.\n");
+ cur_rate = aux_rate;
+ }
+ clk_set_rate(l2_pri_mux_clk, aux_rate);
+ clk_set_rate(l2_pri_mux_clk, 2);
+ clk_set_rate(l2_pri_mux_clk, cur_rate);
+ pr_info("L2 @ %lu KHz\n", clk_get_rate(l2_pri_mux_clk) / 1000);
+ for_each_possible_cpu(cpu) {
+ clk = clks[cpu];
+ cur_rate = clk_get_rate(clk);
+ if (cur_rate == 1) {
+ pr_info("CPU%d @ QSB rate. Forcing new rate.\n", cpu);
+ cur_rate = aux_rate;
+ }
+
+ clk_set_rate(clk, aux_rate);
+ clk_set_rate(clk, 2);
+ clk_set_rate(clk, cur_rate);
+ pr_info("CPU%d @ %lu KHz\n", cpu, clk_get_rate(clk) / 1000);
+ }
+
+ of_clk_add_provider(dev->of_node, krait_of_get, clks);
+
+ return 0;
+}
+
+static struct platform_driver krait_cc_driver = {
+ .probe = krait_cc_probe,
+ .driver = {
+ .name = "krait-cc",
+ .of_match_table = krait_cc_match_table,
+ },
+};
+module_platform_driver(krait_cc_driver);
+
+MODULE_DESCRIPTION("Krait CPU Clock Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:krait-cc");
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 10/15] devicetree: bindings: Document qcom,kpss-gcc
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
The ACC and GCC regions present in KPSSv1 contain registers to
control clocks and power to each Krait CPU and L2. Documenting
the bindings here.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
.../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 7 +++++
.../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 32 ++++++++++++++++++++++
2 files changed, 39 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
index 1333db9..382a574 100644
--- a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt
@@ -21,10 +21,17 @@ PROPERTIES
the register region. An optional second element specifies
the base address and size of the alias register region.
+- clock-output-names:
+ Usage: optional
+ Value type: <string>
+ Definition: Name of the output clock. Typically acpuX_aux where X is a
+ CPU number starting at 0.
+
Example:
clock-controller@2088000 {
compatible = "qcom,kpss-acc-v2";
reg = <0x02088000 0x1000>,
<0x02008000 0x1000>;
+ clock-output-names = "acpu0_aux";
};
diff --git a/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
new file mode 100644
index 0000000..37fc0a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
@@ -0,0 +1,32 @@
+Krait Processor Sub-system (KPSS) Global Clock Controller (GCC)
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: should be one of the following. The generic compatible
+ "qcom,kpss-gcc" should also be included.
+ "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc"
+ "qcom,kpss-gcc-apq8064", "qcom,kpss-gcc"
+ "qcom,kpss-gcc-msm8974", "qcom,kpss-gcc"
+ "qcom,kpss-gcc-msm8960", "qcom,kpss-gcc"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: base address and size of the register region
+
+- clock-output-names:
+ Usage: required
+ Value type: <string>
+ Definition: Name of the output clock. Typically acpu_l2_aux indicating
+ an L2 cache auxiliary clock.
+
+Example:
+
+ l2cc: clock-controller@2011000 {
+ compatible = "qcom,kpss-gcc-ipq8064", "qcom,kpss-gcc";
+ reg = <0x2011000 0x1000>;
+ clock-output-names = "acpu_l2_aux";
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 09/15] clk: qcom: Add KPSS ACC/GCC driver
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
mturquette-rdvid1DuHRBWk0Htik3J/w, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, andy.gross-QSEj5FYQhm4dnm+yROfE0A,
david.brown-QSEj5FYQhm4dnm+yROfE0A, rjw-LthD3rsA81gm4RdzfppkhA,
viresh.kumar-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-soc-u79uwXL29TY76Z2rM5mHXA, linux-pm-u79uwXL29TY76Z2rM5mHXA
Cc: sricharan-sgV2jX0FEOL9JmXXK+q4OQ
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
The ACC and GCC regions present in KPSSv1 contain registers to
control clocks and power to each Krait CPU and L2. For CPUfreq
purposes probe these devices and expose a mux clock that chooses
between PXO and PLL8.
Cc: <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Signed-off-by: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/clk/qcom/Kconfig | 8 +++++
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/kpss-xcc.c | 87 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 96 insertions(+)
create mode 100644 drivers/clk/qcom/kpss-xcc.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 6592595..17dcb88 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -214,6 +214,14 @@ config QCOM_HFPLL
Say Y if you want to support CPU frequency scaling on devices
such as MSM8974, APQ8084, etc.
+config KPSS_XCC
+ tristate "KPSS Clock Controller"
+ depends on COMMON_CLK_QCOM
+ help
+ Support for the Krait ACC and GCC clock controllers. Say Y
+ if you want to support CPU frequency scaling on devices such
+ as MSM8960, APQ8064, etc.
+
config KRAIT_CLOCKS
bool
select KRAIT_L2_ACCESSORS
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index b6741b0..7ad2302 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -37,4 +37,5 @@ obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
+obj-$(CONFIG_KPSS_XCC) += kpss-xcc.o
obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
diff --git a/drivers/clk/qcom/kpss-xcc.c b/drivers/clk/qcom/kpss-xcc.c
new file mode 100644
index 0000000..f260d8f
--- /dev/null
+++ b/drivers/clk/qcom/kpss-xcc.c
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+
+static const char *aux_parents[] = {
+ "pll8_vote",
+ "pxo",
+};
+
+static unsigned int aux_parent_map[] = {
+ 3,
+ 0,
+};
+
+static const struct of_device_id kpss_xcc_match_table[] = {
+ { .compatible = "qcom,kpss-acc-v1", .data = (void *)1UL },
+ { .compatible = "qcom,kpss-gcc" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, kpss_xcc_match_table);
+
+static int kpss_xcc_driver_probe(struct platform_device *pdev)
+{
+ const struct of_device_id *id;
+ struct clk *clk;
+ struct resource *res;
+ void __iomem *base;
+ const char *name;
+
+ id = of_match_device(kpss_xcc_match_table, &pdev->dev);
+ if (!id)
+ return -ENODEV;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ if (id->data) {
+ if (of_property_read_string_index(pdev->dev.of_node,
+ "clock-output-names",
+ 0, &name))
+ return -ENODEV;
+ base += 0x14;
+ } else {
+ name = "acpu_l2_aux";
+ base += 0x28;
+ }
+
+ clk = clk_register_mux_table(&pdev->dev, name, aux_parents,
+ ARRAY_SIZE(aux_parents), 0, base, 0, 0x3,
+ 0, aux_parent_map, NULL);
+
+ platform_set_drvdata(pdev, clk);
+
+ return PTR_ERR_OR_ZERO(clk);
+}
+
+static int kpss_xcc_driver_remove(struct platform_device *pdev)
+{
+ clk_unregister_mux(platform_get_drvdata(pdev));
+ return 0;
+}
+
+static struct platform_driver kpss_xcc_driver = {
+ .probe = kpss_xcc_driver_probe,
+ .remove = kpss_xcc_driver_remove,
+ .driver = {
+ .name = "kpss-xcc",
+ .of_match_table = kpss_xcc_match_table,
+ },
+};
+module_platform_driver(kpss_xcc_driver);
+
+MODULE_DESCRIPTION("Krait Processor Sub System (KPSS) Clock Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:kpss-xcc");
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 08/15] clk: qcom: Add support for Krait clocks
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
The Krait clocks are made up of a series of muxes and a divider
that choose between a fixed rate clock and dedicated HFPLLs for
each CPU. Instead of using mmio accesses to remux parents, the
Krait implementation exposes the remux control via cp15
registers. Support these clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 4 ++
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-krait.c | 124 +++++++++++++++++++++++++++++++++++++++++++
drivers/clk/qcom/clk-krait.h | 38 +++++++++++++
4 files changed, 167 insertions(+)
create mode 100644 drivers/clk/qcom/clk-krait.c
create mode 100644 drivers/clk/qcom/clk-krait.h
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 6c811bd..6592595 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -213,3 +213,7 @@ config QCOM_HFPLL
Support for the high-frequency PLLs present on Qualcomm devices.
Say Y if you want to support CPU frequency scaling on devices
such as MSM8974, APQ8084, etc.
+
+config KRAIT_CLOCKS
+ bool
+ select KRAIT_L2_ACCESSORS
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 4a4bf38..b6741b0 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -10,6 +10,7 @@ clk-qcom-y += clk-rcg2.o
clk-qcom-y += clk-branch.o
clk-qcom-y += clk-regmap-divider.o
clk-qcom-y += clk-regmap-mux.o
+clk-qcom-$(CONFIG_KRAIT_CLOCKS) += clk-krait.o
clk-qcom-y += clk-hfpll.o
clk-qcom-y += reset.o
clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o
diff --git a/drivers/clk/qcom/clk-krait.c b/drivers/clk/qcom/clk-krait.c
new file mode 100644
index 0000000..361c701
--- /dev/null
+++ b/drivers/clk/qcom/clk-krait.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+
+#include <asm/krait-l2-accessors.h>
+
+#include "clk-krait.h"
+
+/* Secondary and primary muxes share the same cp15 register */
+static DEFINE_SPINLOCK(krait_clock_reg_lock);
+
+#define LPL_SHIFT 8
+static void __krait_mux_set_sel(struct krait_mux_clk *mux, int sel)
+{
+ unsigned long flags;
+ u32 regval;
+
+ spin_lock_irqsave(&krait_clock_reg_lock, flags);
+ regval = krait_get_l2_indirect_reg(mux->offset);
+ regval &= ~(mux->mask << mux->shift);
+ regval |= (sel & mux->mask) << mux->shift;
+ if (mux->lpl) {
+ regval &= ~(mux->mask << (mux->shift + LPL_SHIFT));
+ regval |= (sel & mux->mask) << (mux->shift + LPL_SHIFT);
+ }
+ krait_set_l2_indirect_reg(mux->offset, regval);
+ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
+
+ /* Wait for switch to complete. */
+ mb();
+ udelay(1);
+}
+
+static int krait_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
+ u32 sel;
+
+ sel = clk_mux_reindex(index, mux->parent_map, 0);
+ mux->en_mask = sel;
+ /* Don't touch mux if CPU is off as it won't work */
+ if (__clk_is_enabled(hw->clk))
+ __krait_mux_set_sel(mux, sel);
+
+ return 0;
+}
+
+static u8 krait_mux_get_parent(struct clk_hw *hw)
+{
+ struct krait_mux_clk *mux = to_krait_mux_clk(hw);
+ u32 sel;
+
+ sel = krait_get_l2_indirect_reg(mux->offset);
+ sel >>= mux->shift;
+ sel &= mux->mask;
+ mux->en_mask = sel;
+
+ return clk_mux_get_parent(hw, sel, mux->parent_map, 0);
+}
+
+const struct clk_ops krait_mux_clk_ops = {
+ .set_parent = krait_mux_set_parent,
+ .get_parent = krait_mux_get_parent,
+ .determine_rate = __clk_mux_determine_rate_closest,
+};
+EXPORT_SYMBOL_GPL(krait_mux_clk_ops);
+
+/* The divider can divide by 2, 4, 6 and 8. But we only really need div-2. */
+static long krait_div2_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ *parent_rate = clk_hw_round_rate(clk_hw_get_parent(hw), rate * 2);
+ return DIV_ROUND_UP(*parent_rate, 2);
+}
+
+static int krait_div2_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct krait_div2_clk *d = to_krait_div2_clk(hw);
+ unsigned long flags;
+ u32 val;
+ u32 mask = BIT(d->width) - 1;
+
+ if (d->lpl)
+ mask = mask << (d->shift + LPL_SHIFT) | mask << d->shift;
+
+ spin_lock_irqsave(&krait_clock_reg_lock, flags);
+ val = krait_get_l2_indirect_reg(d->offset);
+ val &= ~mask;
+ krait_set_l2_indirect_reg(d->offset, val);
+ spin_unlock_irqrestore(&krait_clock_reg_lock, flags);
+
+ return 0;
+}
+
+static unsigned long
+krait_div2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
+{
+ struct krait_div2_clk *d = to_krait_div2_clk(hw);
+ u32 mask = BIT(d->width) - 1;
+ u32 div;
+
+ div = krait_get_l2_indirect_reg(d->offset);
+ div >>= d->shift;
+ div &= mask;
+ div = (div + 1) * 2;
+
+ return DIV_ROUND_UP(parent_rate, div);
+}
+
+const struct clk_ops krait_div2_clk_ops = {
+ .round_rate = krait_div2_round_rate,
+ .set_rate = krait_div2_set_rate,
+ .recalc_rate = krait_div2_recalc_rate,
+};
+EXPORT_SYMBOL_GPL(krait_div2_clk_ops);
diff --git a/drivers/clk/qcom/clk-krait.h b/drivers/clk/qcom/clk-krait.h
new file mode 100644
index 0000000..d5c9c60
--- /dev/null
+++ b/drivers/clk/qcom/clk-krait.h
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#ifndef __QCOM_CLK_KRAIT_H
+#define __QCOM_CLK_KRAIT_H
+
+#include <linux/clk-provider.h>
+
+struct krait_mux_clk {
+ unsigned int *parent_map;
+ u32 offset;
+ u32 mask;
+ u32 shift;
+ u32 en_mask;
+ bool lpl;
+
+ struct clk_hw hw;
+ struct notifier_block clk_nb;
+};
+
+#define to_krait_mux_clk(_hw) container_of(_hw, struct krait_mux_clk, hw)
+
+extern const struct clk_ops krait_mux_clk_ops;
+
+struct krait_div2_clk {
+ u32 offset;
+ u8 width;
+ u32 shift;
+ bool lpl;
+
+ struct clk_hw hw;
+};
+
+#define to_krait_div2_clk(_hw) container_of(_hw, struct krait_div2_clk, hw)
+
+extern const struct clk_ops krait_div2_clk_ops;
+
+#endif
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 07/15] clk: qcom: Add IPQ806X's HFPLLs
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
Describe the HFPLLs present on IPQ806X devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/gcc-ipq806x.c | 82 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 82 insertions(+)
diff --git a/drivers/clk/qcom/gcc-ipq806x.c b/drivers/clk/qcom/gcc-ipq806x.c
index 28eb200..d571cf8 100644
--- a/drivers/clk/qcom/gcc-ipq806x.c
+++ b/drivers/clk/qcom/gcc-ipq806x.c
@@ -30,6 +30,7 @@
#include "clk-pll.h"
#include "clk-rcg.h"
#include "clk-branch.h"
+#include "clk-hfpll.h"
#include "reset.h"
static struct clk_pll pll0 = {
@@ -113,6 +114,84 @@
},
};
+static struct hfpll_data hfpll0_data = {
+ .mode_reg = 0x3200,
+ .l_reg = 0x3208,
+ .m_reg = 0x320c,
+ .n_reg = 0x3210,
+ .config_reg = 0x3204,
+ .status_reg = 0x321c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3214,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll0 = {
+ .d = &hfpll0_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll0",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock),
+};
+
+static struct hfpll_data hfpll1_data = {
+ .mode_reg = 0x3240,
+ .l_reg = 0x3248,
+ .m_reg = 0x324c,
+ .n_reg = 0x3250,
+ .config_reg = 0x3244,
+ .status_reg = 0x325c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3314,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll1 = {
+ .d = &hfpll1_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll1",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock),
+};
+
+static struct hfpll_data hfpll_l2_data = {
+ .mode_reg = 0x3300,
+ .l_reg = 0x3308,
+ .m_reg = 0x330c,
+ .n_reg = 0x3310,
+ .config_reg = 0x3304,
+ .status_reg = 0x331c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3314,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll_l2 = {
+ .d = &hfpll_l2_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll_l2",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock),
+};
+
static struct clk_pll pll14 = {
.l_reg = 0x31c4,
.m_reg = 0x31c8,
@@ -2800,6 +2879,9 @@ enum {
[UBI32_CORE2_CLK_SRC] = &ubi32_core2_src_clk.clkr,
[NSSTCM_CLK_SRC] = &nss_tcm_src.clkr,
[NSSTCM_CLK] = &nss_tcm_clk.clkr,
+ [PLL9] = &hfpll0.clkr,
+ [PLL10] = &hfpll1.clkr,
+ [PLL12] = &hfpll_l2.clkr,
};
static const struct qcom_reset_map gcc_ipq806x_resets[] = {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 06/15] clk: qcom: Add MSM8960/APQ8064's HFPLLs
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
Describe the HFPLLs present on MSM8960 and APQ8064 devices.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/gcc-msm8960.c | 172 +++++++++++++++++++++++++++
include/dt-bindings/clock/qcom,gcc-msm8960.h | 2 +
2 files changed, 174 insertions(+)
diff --git a/drivers/clk/qcom/gcc-msm8960.c b/drivers/clk/qcom/gcc-msm8960.c
index eb551c7..809f16a 100644
--- a/drivers/clk/qcom/gcc-msm8960.c
+++ b/drivers/clk/qcom/gcc-msm8960.c
@@ -30,6 +30,7 @@
#include "clk-pll.h"
#include "clk-rcg.h"
#include "clk-branch.h"
+#include "clk-hfpll.h"
#include "reset.h"
static struct clk_pll pll3 = {
@@ -86,6 +87,164 @@
},
};
+static struct hfpll_data hfpll0_data = {
+ .mode_reg = 0x3200,
+ .l_reg = 0x3208,
+ .m_reg = 0x320c,
+ .n_reg = 0x3210,
+ .config_reg = 0x3204,
+ .status_reg = 0x321c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3214,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll0 = {
+ .d = &hfpll0_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll0",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll0.lock),
+};
+
+static struct hfpll_data hfpll1_8064_data = {
+ .mode_reg = 0x3240,
+ .l_reg = 0x3248,
+ .m_reg = 0x324c,
+ .n_reg = 0x3250,
+ .config_reg = 0x3244,
+ .status_reg = 0x325c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3254,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct hfpll_data hfpll1_data = {
+ .mode_reg = 0x3300,
+ .l_reg = 0x3308,
+ .m_reg = 0x330c,
+ .n_reg = 0x3310,
+ .config_reg = 0x3304,
+ .status_reg = 0x331c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3314,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll1 = {
+ .d = &hfpll1_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll1",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll1.lock),
+};
+
+static struct hfpll_data hfpll2_data = {
+ .mode_reg = 0x3280,
+ .l_reg = 0x3288,
+ .m_reg = 0x328c,
+ .n_reg = 0x3290,
+ .config_reg = 0x3284,
+ .status_reg = 0x329c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3294,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll2 = {
+ .d = &hfpll2_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll2",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll2.lock),
+};
+
+static struct hfpll_data hfpll3_data = {
+ .mode_reg = 0x32c0,
+ .l_reg = 0x32c8,
+ .m_reg = 0x32cc,
+ .n_reg = 0x32d0,
+ .config_reg = 0x32c4,
+ .status_reg = 0x32dc,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x32d4,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll3 = {
+ .d = &hfpll3_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll3",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll3.lock),
+};
+
+static struct hfpll_data hfpll_l2_8064_data = {
+ .mode_reg = 0x3300,
+ .l_reg = 0x3308,
+ .m_reg = 0x330c,
+ .n_reg = 0x3310,
+ .config_reg = 0x3304,
+ .status_reg = 0x331c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3314,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct hfpll_data hfpll_l2_data = {
+ .mode_reg = 0x3400,
+ .l_reg = 0x3408,
+ .m_reg = 0x340c,
+ .n_reg = 0x3410,
+ .config_reg = 0x3404,
+ .status_reg = 0x341c,
+ .config_val = 0x7845c665,
+ .droop_reg = 0x3414,
+ .droop_val = 0x0108c000,
+ .min_rate = 600000000UL,
+ .max_rate = 1800000000UL,
+};
+
+static struct clk_hfpll hfpll_l2 = {
+ .d = &hfpll_l2_data,
+ .clkr.hw.init = &(struct clk_init_data){
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .name = "hfpll_l2",
+ .ops = &clk_ops_hfpll,
+ .flags = CLK_IGNORE_UNUSED,
+ },
+ .lock = __SPIN_LOCK_UNLOCKED(hfpll_l2.lock),
+};
+
static struct clk_pll pll14 = {
.l_reg = 0x31c4,
.m_reg = 0x31c8,
@@ -3112,6 +3271,9 @@ enum {
[PMIC_ARB1_H_CLK] = &pmic_arb1_h_clk.clkr,
[PMIC_SSBI2_CLK] = &pmic_ssbi2_clk.clkr,
[RPM_MSG_RAM_H_CLK] = &rpm_msg_ram_h_clk.clkr,
+ [PLL9] = &hfpll0.clkr,
+ [PLL10] = &hfpll1.clkr,
+ [PLL12] = &hfpll_l2.clkr,
};
static const struct qcom_reset_map gcc_msm8960_resets[] = {
@@ -3323,6 +3485,11 @@ enum {
[PMIC_ARB1_H_CLK] = &pmic_arb1_h_clk.clkr,
[PMIC_SSBI2_CLK] = &pmic_ssbi2_clk.clkr,
[RPM_MSG_RAM_H_CLK] = &rpm_msg_ram_h_clk.clkr,
+ [PLL9] = &hfpll0.clkr,
+ [PLL10] = &hfpll1.clkr,
+ [PLL12] = &hfpll_l2.clkr,
+ [PLL16] = &hfpll2.clkr,
+ [PLL17] = &hfpll3.clkr,
};
static const struct qcom_reset_map gcc_apq8064_resets[] = {
@@ -3482,6 +3649,11 @@ static int gcc_msm8960_probe(struct platform_device *pdev)
if (ret)
return ret;
+ if (match->data == &gcc_apq8064_desc) {
+ hfpll1.d = &hfpll1_8064_data;
+ hfpll_l2.d = &hfpll_l2_8064_data;
+ }
+
tsens = platform_device_register_data(&pdev->dev, "qcom-tsens", -1,
NULL, 0);
if (IS_ERR(tsens))
diff --git a/include/dt-bindings/clock/qcom,gcc-msm8960.h b/include/dt-bindings/clock/qcom,gcc-msm8960.h
index 7d20eed..e02742f 100644
--- a/include/dt-bindings/clock/qcom,gcc-msm8960.h
+++ b/include/dt-bindings/clock/qcom,gcc-msm8960.h
@@ -319,5 +319,7 @@
#define CE3_SRC 303
#define CE3_CORE_CLK 304
#define CE3_H_CLK 305
+#define PLL16 306
+#define PLL17 307
#endif
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 05/15] devicetree: bindings: Document qcom,hfpll
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
mturquette-rdvid1DuHRBWk0Htik3J/w, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, andy.gross-QSEj5FYQhm4dnm+yROfE0A,
david.brown-QSEj5FYQhm4dnm+yROfE0A, rjw-LthD3rsA81gm4RdzfppkhA,
viresh.kumar-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-soc-u79uwXL29TY76Z2rM5mHXA, linux-pm-u79uwXL29TY76Z2rM5mHXA
Cc: sricharan-sgV2jX0FEOL9JmXXK+q4OQ
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Adds bindings document for qcom,hfpll instantiated within
the Krait processor subsystem as separate register region.
Signed-off-by: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
.../devicetree/bindings/clock/qcom,hfpll.txt | 46 ++++++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt
diff --git a/Documentation/devicetree/bindings/clock/qcom,hfpll.txt b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt
new file mode 100644
index 0000000..771cb0a
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,hfpll.txt
@@ -0,0 +1,46 @@
+High-Frequency PLL (HFPLL)
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>:
+ shall contain only one of the following. The generic
+ compatible "qcom,hfpll" should be also included.
+
+ "qcom,hfpll-ipq8064", "qcom,hfpll"
+ "qcom,hfpll-apq8064", "qcom,hfpll"
+ "qcom,hfpll-msm8974", "qcom,hfpll"
+ "qcom,hfpll-msm8960", "qcom,hfpll"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: address and size of HPLL registers. An optional second
+ element specifies the address and size of the alias
+ register region.
+
+- clock-output-names:
+ Usage: required
+ Value type: <string>
+ Definition: Name of the PLL. Typically hfpllX where X is a CPU number
+ starting at 0. Otherwise hfpll_Y where Y is more specific
+ such as "l2".
+
+Example:
+
+1) An HFPLL for the L2 cache.
+
+ clock-controller@f9016000 {
+ compatible = "qcom,hfpll-ipq8064", "qcom,hfpll";
+ reg = <0xf9016000 0x30>;
+ clock-output-names = "hfpll_l2";
+ };
+
+2) An HFPLL for CPU0. This HFPLL has the alias register region.
+
+ clock-controller@f908a000 {
+ compatible = "qcom,hfpll-ipq8064", "qcom,hfpll";
+ reg = <0xf908a000 0x30>, <0xf900a000 0x30>;
+ clock-output-names = "hfpll0";
+ };
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 04/15] clk: qcom: Add HFPLL driver
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
On some devices (MSM8974 for example), the HFPLLs are
instantiated within the Krait processor subsystem as separate
register regions. Add a driver for these PLLs so that we can
provide HFPLL clocks for use by the system.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 8 ++++
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/hfpll.c | 96 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 105 insertions(+)
create mode 100644 drivers/clk/qcom/hfpll.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index 20b5d6f..6c811bd 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -205,3 +205,11 @@ config SPMI_PMIC_CLKDIV
Technologies, Inc. SPMI PMIC. It configures the frequency of
clkdiv outputs of the PMIC. These clocks are typically wired
through alternate functions on GPIO pins.
+
+config QCOM_HFPLL
+ tristate "High-Frequency PLL (HFPLL) Clock Controller"
+ depends on COMMON_CLK_QCOM
+ help
+ Support for the high-frequency PLLs present on Qualcomm devices.
+ Say Y if you want to support CPU frequency scaling on devices
+ such as MSM8974, APQ8084, etc.
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 4795e21..4a4bf38 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -36,3 +36,4 @@ obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
+obj-$(CONFIG_QCOM_HFPLL) += hfpll.o
diff --git a/drivers/clk/qcom/hfpll.c b/drivers/clk/qcom/hfpll.c
new file mode 100644
index 0000000..7443239
--- /dev/null
+++ b/drivers/clk/qcom/hfpll.c
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+
+#include "clk-regmap.h"
+#include "clk-hfpll.h"
+
+static const struct hfpll_data hdata = {
+ .mode_reg = 0x00,
+ .l_reg = 0x04,
+ .m_reg = 0x08,
+ .n_reg = 0x0c,
+ .user_reg = 0x10,
+ .config_reg = 0x14,
+ .config_val = 0x430405d,
+ .status_reg = 0x1c,
+ .lock_bit = 16,
+
+ .user_val = 0x8,
+ .user_vco_mask = 0x100000,
+ .low_vco_max_rate = 1248000000,
+ .min_rate = 537600000UL,
+ .max_rate = 2900000000UL,
+};
+
+static const struct of_device_id qcom_hfpll_match_table[] = {
+ { .compatible = "qcom,hfpll" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_hfpll_match_table);
+
+static const struct regmap_config hfpll_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x30,
+ .fast_io = true,
+};
+
+static int qcom_hfpll_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ struct device *dev = &pdev->dev;
+ void __iomem *base;
+ struct regmap *regmap;
+ struct clk_hfpll *h;
+ struct clk_init_data init = {
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_ops_hfpll,
+ };
+
+ h = devm_kzalloc(dev, sizeof(*h), GFP_KERNEL);
+ if (!h)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ regmap = devm_regmap_init_mmio(&pdev->dev, base, &hfpll_regmap_config);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ if (of_property_read_string_index(dev->of_node, "clock-output-names",
+ 0, &init.name))
+ return -ENODEV;
+
+ h->d = &hdata;
+ h->clkr.hw.init = &init;
+ spin_lock_init(&h->lock);
+
+ return devm_clk_register_regmap(&pdev->dev, &h->clkr);
+}
+
+static struct platform_driver qcom_hfpll_driver = {
+ .probe = qcom_hfpll_probe,
+ .driver = {
+ .name = "qcom-hfpll",
+ .of_match_table = qcom_hfpll_match_table,
+ },
+};
+module_platform_driver(qcom_hfpll_driver);
+
+MODULE_DESCRIPTION("QCOM HFPLL Clock Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:qcom-hfpll");
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 03/15] clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
HFPLLs are the main frequency source for Krait CPU clocks. Add
support for changing the rate of these PLLs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-hfpll.c | 244 +++++++++++++++++++++++++++++++++++++++++++
drivers/clk/qcom/clk-hfpll.h | 45 ++++++++
3 files changed, 290 insertions(+)
create mode 100644 drivers/clk/qcom/clk-hfpll.c
create mode 100644 drivers/clk/qcom/clk-hfpll.h
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 602af38..4795e21 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -10,6 +10,7 @@ clk-qcom-y += clk-rcg2.o
clk-qcom-y += clk-branch.o
clk-qcom-y += clk-regmap-divider.o
clk-qcom-y += clk-regmap-mux.o
+clk-qcom-y += clk-hfpll.o
clk-qcom-y += reset.o
clk-qcom-$(CONFIG_QCOM_GDSC) += gdsc.o
diff --git a/drivers/clk/qcom/clk-hfpll.c b/drivers/clk/qcom/clk-hfpll.c
new file mode 100644
index 0000000..6d87ca4
--- /dev/null
+++ b/drivers/clk/qcom/clk-hfpll.c
@@ -0,0 +1,244 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/kernel.h>
+#include <linux/export.h>
+#include <linux/regmap.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+
+#include "clk-regmap.h"
+#include "clk-hfpll.h"
+
+#define PLL_OUTCTRL BIT(0)
+#define PLL_BYPASSNL BIT(1)
+#define PLL_RESET_N BIT(2)
+
+/* Initialize a HFPLL at a given rate and enable it. */
+static void __clk_hfpll_init_once(struct clk_hw *hw)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+
+ if (likely(h->init_done))
+ return;
+
+ /* Configure PLL parameters for integer mode. */
+ if (hd->config_val)
+ regmap_write(regmap, hd->config_reg, hd->config_val);
+ regmap_write(regmap, hd->m_reg, 0);
+ regmap_write(regmap, hd->n_reg, 1);
+
+ if (hd->user_reg) {
+ u32 regval = hd->user_val;
+ unsigned long rate;
+
+ rate = clk_hw_get_rate(hw);
+
+ /* Pick the right VCO. */
+ if (hd->user_vco_mask && rate > hd->low_vco_max_rate)
+ regval |= hd->user_vco_mask;
+ regmap_write(regmap, hd->user_reg, regval);
+ }
+
+ if (hd->droop_reg)
+ regmap_write(regmap, hd->droop_reg, hd->droop_val);
+
+ h->init_done = true;
+}
+
+static void __clk_hfpll_enable(struct clk_hw *hw)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ u32 val;
+
+ __clk_hfpll_init_once(hw);
+
+ /* Disable PLL bypass mode. */
+ regmap_update_bits(regmap, hd->mode_reg, PLL_BYPASSNL, PLL_BYPASSNL);
+
+ /*
+ * H/W requires a 5us delay between disabling the bypass and
+ * de-asserting the reset. Delay 10us just to be safe.
+ */
+ udelay(10);
+
+ /* De-assert active-low PLL reset. */
+ regmap_update_bits(regmap, hd->mode_reg, PLL_RESET_N, PLL_RESET_N);
+
+ /* Wait for PLL to lock. */
+ if (hd->status_reg) {
+ do {
+ regmap_read(regmap, hd->status_reg, &val);
+ } while (!(val & BIT(hd->lock_bit)));
+ } else {
+ udelay(60);
+ }
+
+ /* Enable PLL output. */
+ regmap_update_bits(regmap, hd->mode_reg, PLL_OUTCTRL, PLL_OUTCTRL);
+}
+
+/* Enable an already-configured HFPLL. */
+static int clk_hfpll_enable(struct clk_hw *hw)
+{
+ unsigned long flags;
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ u32 mode;
+
+ spin_lock_irqsave(&h->lock, flags);
+ regmap_read(regmap, hd->mode_reg, &mode);
+ if (!(mode & (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)))
+ __clk_hfpll_enable(hw);
+ spin_unlock_irqrestore(&h->lock, flags);
+
+ return 0;
+}
+
+static void __clk_hfpll_disable(struct clk_hfpll *h)
+{
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+
+ /*
+ * Disable the PLL output, disable test mode, enable the bypass mode,
+ * and assert the reset.
+ */
+ regmap_update_bits(regmap, hd->mode_reg,
+ PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL, 0);
+}
+
+static void clk_hfpll_disable(struct clk_hw *hw)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ unsigned long flags;
+
+ spin_lock_irqsave(&h->lock, flags);
+ __clk_hfpll_disable(h);
+ spin_unlock_irqrestore(&h->lock, flags);
+}
+
+static long clk_hfpll_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ unsigned long rrate;
+
+ rate = clamp(rate, hd->min_rate, hd->max_rate);
+
+ rrate = DIV_ROUND_UP(rate, *parent_rate) * *parent_rate;
+ if (rrate > hd->max_rate)
+ rrate -= *parent_rate;
+
+ return rrate;
+}
+
+/*
+ * For optimization reasons, assumes no downstream clocks are actively using
+ * it.
+ */
+static int clk_hfpll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ unsigned long flags;
+ u32 l_val, val;
+ bool enabled;
+
+ l_val = rate / parent_rate;
+
+ spin_lock_irqsave(&h->lock, flags);
+
+ enabled = __clk_is_enabled(hw->clk);
+ if (enabled)
+ __clk_hfpll_disable(h);
+
+ /* Pick the right VCO. */
+ if (hd->user_reg && hd->user_vco_mask) {
+ regmap_read(regmap, hd->user_reg, &val);
+ if (rate <= hd->low_vco_max_rate)
+ val &= ~hd->user_vco_mask;
+ else
+ val |= hd->user_vco_mask;
+ regmap_write(regmap, hd->user_reg, val);
+ }
+
+ regmap_write(regmap, hd->l_reg, l_val);
+
+ if (enabled)
+ __clk_hfpll_enable(hw);
+
+ spin_unlock_irqrestore(&h->lock, flags);
+
+ return 0;
+}
+
+static unsigned long clk_hfpll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ u32 l_val;
+
+ regmap_read(regmap, hd->l_reg, &l_val);
+
+ return l_val * parent_rate;
+}
+
+static void clk_hfpll_init(struct clk_hw *hw)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ u32 mode, status;
+
+ regmap_read(regmap, hd->mode_reg, &mode);
+ if (mode != (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL)) {
+ __clk_hfpll_init_once(hw);
+ return;
+ }
+
+ if (hd->status_reg) {
+ regmap_read(regmap, hd->status_reg, &status);
+ if (!(status & BIT(hd->lock_bit))) {
+ WARN(1, "HFPLL %s is ON, but not locked!\n",
+ __clk_get_name(hw->clk));
+ clk_hfpll_disable(hw);
+ __clk_hfpll_init_once(hw);
+ }
+ }
+}
+
+static int hfpll_is_enabled(struct clk_hw *hw)
+{
+ struct clk_hfpll *h = to_clk_hfpll(hw);
+ struct hfpll_data const *hd = h->d;
+ struct regmap *regmap = h->clkr.regmap;
+ u32 mode;
+
+ regmap_read(regmap, hd->mode_reg, &mode);
+ mode &= 0x7;
+ return mode == (PLL_BYPASSNL | PLL_RESET_N | PLL_OUTCTRL);
+}
+
+const struct clk_ops clk_ops_hfpll = {
+ .enable = clk_hfpll_enable,
+ .disable = clk_hfpll_disable,
+ .is_enabled = hfpll_is_enabled,
+ .round_rate = clk_hfpll_round_rate,
+ .set_rate = clk_hfpll_set_rate,
+ .recalc_rate = clk_hfpll_recalc_rate,
+ .init = clk_hfpll_init,
+};
+EXPORT_SYMBOL_GPL(clk_ops_hfpll);
diff --git a/drivers/clk/qcom/clk-hfpll.h b/drivers/clk/qcom/clk-hfpll.h
new file mode 100644
index 0000000..aae5a78
--- /dev/null
+++ b/drivers/clk/qcom/clk-hfpll.h
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#ifndef __QCOM_CLK_HFPLL_H__
+#define __QCOM_CLK_HFPLL_H__
+
+#include <linux/clk-provider.h>
+#include <linux/spinlock.h>
+#include "clk-regmap.h"
+
+struct hfpll_data {
+ u32 mode_reg;
+ u32 l_reg;
+ u32 m_reg;
+ u32 n_reg;
+ u32 user_reg;
+ u32 droop_reg;
+ u32 config_reg;
+ u32 status_reg;
+ u8 lock_bit;
+
+ u32 droop_val;
+ u32 config_val;
+ u32 user_val;
+ u32 user_vco_mask;
+ unsigned long low_vco_max_rate;
+
+ unsigned long min_rate;
+ unsigned long max_rate;
+};
+
+struct clk_hfpll {
+ struct hfpll_data const *d;
+ int init_done;
+
+ struct clk_regmap clkr;
+ spinlock_t lock;
+};
+
+#define to_clk_hfpll(_hw) \
+ container_of(to_clk_regmap(_hw), struct clk_hfpll, clkr)
+
+extern const struct clk_ops clk_ops_hfpll;
+
+#endif
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 02/15] clk: mux: Split out register accessors for reuse
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
mturquette-rdvid1DuHRBWk0Htik3J/w, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, andy.gross-QSEj5FYQhm4dnm+yROfE0A,
david.brown-QSEj5FYQhm4dnm+yROfE0A, rjw-LthD3rsA81gm4RdzfppkhA,
viresh.kumar-QSEj5FYQhm4dnm+yROfE0A,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-clk-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-soc-u79uwXL29TY76Z2rM5mHXA, linux-pm-u79uwXL29TY76Z2rM5mHXA
Cc: sricharan-sgV2jX0FEOL9JmXXK+q4OQ
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
From: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
We want to reuse the logic in clk-mux.c for other clock drivers
that don't use readl as register accessors. Fortunately, there
really isn't much to the mux code besides the table indirection
and quirk flags if you assume any bit shifting and masking has
been done already. Pull that logic out into reusable functions
that operate on an optional table and some flags so that other
drivers can use the same logic.
[Sricharan: Rebased for mainline]
Signed-off-by: Sricharan R <sricharan-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/clk/clk-mux.c | 75 +++++++++++++++++++++++++++-----------------
include/linux/clk-provider.h | 9 ++++--
2 files changed, 54 insertions(+), 30 deletions(-)
diff --git a/drivers/clk/clk-mux.c b/drivers/clk/clk-mux.c
index 39cabe1..22ebf99 100644
--- a/drivers/clk/clk-mux.c
+++ b/drivers/clk/clk-mux.c
@@ -26,35 +26,24 @@
* parent - parent is adjustable through clk_set_parent
*/
-static u8 clk_mux_get_parent(struct clk_hw *hw)
+unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
+ unsigned int *table, unsigned long flags)
{
- struct clk_mux *mux = to_clk_mux(hw);
int num_parents = clk_hw_get_num_parents(hw);
- u32 val;
-
- /*
- * FIXME need a mux-specific flag to determine if val is bitwise or numeric
- * e.g. sys_clkin_ck's clksel field is 3 bits wide, but ranges from 0x1
- * to 0x7 (index starts at one)
- * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
- * val = 0x4 really means "bit 2, index starts at bit 0"
- */
- val = clk_readl(mux->reg) >> mux->shift;
- val &= mux->mask;
- if (mux->table) {
+ if (table) {
int i;
for (i = 0; i < num_parents; i++)
- if (mux->table[i] == val)
+ if (table[i] == val)
return i;
return -EINVAL;
}
- if (val && (mux->flags & CLK_MUX_INDEX_BIT))
+ if (val && (flags & CLK_MUX_INDEX_BIT))
val = ffs(val) - 1;
- if (val && (mux->flags & CLK_MUX_INDEX_ONE))
+ if (val && (flags & CLK_MUX_INDEX_ONE))
val--;
if (val >= num_parents)
@@ -62,23 +51,53 @@ static u8 clk_mux_get_parent(struct clk_hw *hw)
return val;
}
+EXPORT_SYMBOL_GPL(clk_mux_get_parent);
-static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
+static u8 _clk_mux_get_parent(struct clk_hw *hw)
{
struct clk_mux *mux = to_clk_mux(hw);
u32 val;
- unsigned long flags = 0;
- if (mux->table) {
- index = mux->table[index];
+ /*
+ * FIXME need a mux-specific flag to determine if val is bitwise or
+ * numeric e.g. sys_clkin_ck's clksel field is 3 bits wide,
+ * but ranges from 0x1 to 0x7 (index starts at one)
+ * OTOH, pmd_trace_clk_mux_ck uses a separate bit for each clock, so
+ * val = 0x4 really means "bit 2, index starts at bit 0"
+ */
+ val = clk_readl(mux->reg) >> mux->shift;
+ val &= mux->mask;
+
+ return clk_mux_get_parent(hw, val, mux->table, mux->flags);
+}
+
+unsigned int clk_mux_reindex(u8 index, unsigned int *table,
+ unsigned long flags)
+{
+ unsigned int val = index;
+
+ if (table) {
+ val = table[val];
} else {
- if (mux->flags & CLK_MUX_INDEX_BIT)
- index = 1 << index;
+ if (flags & CLK_MUX_INDEX_BIT)
+ val = 1 << index;
- if (mux->flags & CLK_MUX_INDEX_ONE)
- index++;
+ if (flags & CLK_MUX_INDEX_ONE)
+ val++;
}
+ return val;
+}
+EXPORT_SYMBOL_GPL(clk_mux_reindex);
+
+static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ struct clk_mux *mux = to_clk_mux(hw);
+ u32 val;
+ unsigned long flags = 0;
+
+ index = clk_mux_reindex(index, mux->table, mux->flags);
+
if (mux->lock)
spin_lock_irqsave(mux->lock, flags);
else
@@ -102,14 +121,14 @@ static int clk_mux_set_parent(struct clk_hw *hw, u8 index)
}
const struct clk_ops clk_mux_ops = {
- .get_parent = clk_mux_get_parent,
+ .get_parent = _clk_mux_get_parent,
.set_parent = clk_mux_set_parent,
.determine_rate = __clk_mux_determine_rate,
};
EXPORT_SYMBOL_GPL(clk_mux_ops);
const struct clk_ops clk_mux_ro_ops = {
- .get_parent = clk_mux_get_parent,
+ .get_parent = _clk_mux_get_parent,
};
EXPORT_SYMBOL_GPL(clk_mux_ro_ops);
@@ -117,7 +136,7 @@ struct clk_hw *clk_hw_register_mux_table(struct device *dev, const char *name,
const char * const *parent_names, u8 num_parents,
unsigned long flags,
void __iomem *reg, u8 shift, u32 mask,
- u8 clk_mux_flags, u32 *table, spinlock_t *lock)
+ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock)
{
struct clk_mux *mux;
struct clk_hw *hw;
diff --git a/include/linux/clk-provider.h b/include/linux/clk-provider.h
index 7c925e6..9578411 100644
--- a/include/linux/clk-provider.h
+++ b/include/linux/clk-provider.h
@@ -468,7 +468,7 @@ struct clk_hw *clk_hw_register_divider_table(struct device *dev,
struct clk_mux {
struct clk_hw hw;
void __iomem *reg;
- u32 *table;
+ unsigned int *table;
u32 mask;
u8 shift;
u8 flags;
@@ -486,6 +486,11 @@ struct clk_mux {
extern const struct clk_ops clk_mux_ops;
extern const struct clk_ops clk_mux_ro_ops;
+unsigned int clk_mux_get_parent(struct clk_hw *hw, unsigned int val,
+ unsigned int *table, unsigned long flags);
+unsigned int clk_mux_reindex(u8 index, unsigned int *table,
+ unsigned long flags);
+
struct clk *clk_register_mux(struct device *dev, const char *name,
const char * const *parent_names, u8 num_parents,
unsigned long flags,
@@ -506,7 +511,7 @@ struct clk_hw *clk_hw_register_mux_table(struct device *dev, const char *name,
const char * const *parent_names, u8 num_parents,
unsigned long flags,
void __iomem *reg, u8 shift, u32 mask,
- u8 clk_mux_flags, u32 *table, spinlock_t *lock);
+ u8 clk_mux_flags, unsigned int *table, spinlock_t *lock);
void clk_unregister_mux(struct clk *clk);
void clk_hw_unregister_mux(struct clk_hw *hw);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH v5 01/15] ARM: Add Krait L2 register accessor functions
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan, Russell King, Courtney Cavin
In-Reply-To: <1513698900-10638-1-git-send-email-sricharan@codeaurora.org>
From: Stephen Boyd <sboyd@codeaurora.org>
Krait CPUs have a handful of L2 cache controller registers that
live behind a cp15 based indirection register. First you program
the indirection register (l2cpselr) to point the L2 'window'
register (l2cpdr) at what you want to read/write. Then you
read/write the 'window' register to do what you want. The
l2cpselr register is not banked per-cpu so we must lock around
accesses to it to prevent other CPUs from re-pointing l2cpdr
underneath us.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
arch/arm/common/Kconfig | 3 ++
arch/arm/common/Makefile | 1 +
arch/arm/common/krait-l2-accessors.c | 48 +++++++++++++++++++++++++++++++
arch/arm/include/asm/krait-l2-accessors.h | 10 +++++++
4 files changed, 62 insertions(+)
create mode 100644 arch/arm/common/krait-l2-accessors.c
create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index e5ad070..c8e1986 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -7,6 +7,9 @@ config DMABOUNCE
bool
select ZONE_DMA
+config KRAIT_L2_ACCESSORS
+ bool
+
config SHARP_LOCOMO
bool
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 70b4a14..eec6cd1 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -7,6 +7,7 @@ obj-y += firmware.o
obj-$(CONFIG_SA1111) += sa1111.o
obj-$(CONFIG_DMABOUNCE) += dmabounce.o
+obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o
obj-$(CONFIG_SHARP_LOCOMO) += locomo.o
obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
diff --git a/arch/arm/common/krait-l2-accessors.c b/arch/arm/common/krait-l2-accessors.c
new file mode 100644
index 0000000..0a7ca58
--- /dev/null
+++ b/arch/arm/common/krait-l2-accessors.c
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include <linux/spinlock.h>
+#include <linux/export.h>
+
+#include <asm/barrier.h>
+#include <asm/krait-l2-accessors.h>
+
+static DEFINE_RAW_SPINLOCK(krait_l2_lock);
+
+void krait_set_l2_indirect_reg(u32 addr, u32 val)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&krait_l2_lock, flags);
+ /*
+ * Select the L2 window by poking l2cpselr, then write to the window
+ * via l2cpdr.
+ */
+ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
+ isb();
+ asm volatile ("mcr p15, 3, %0, c15, c0, 7 @ l2cpdr" : : "r" (val));
+ isb();
+
+ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
+}
+EXPORT_SYMBOL(krait_set_l2_indirect_reg);
+
+u32 krait_get_l2_indirect_reg(u32 addr)
+{
+ u32 val;
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&krait_l2_lock, flags);
+ /*
+ * Select the L2 window by poking l2cpselr, then read from the window
+ * via l2cpdr.
+ */
+ asm volatile ("mcr p15, 3, %0, c15, c0, 6 @ l2cpselr" : : "r" (addr));
+ isb();
+ asm volatile ("mrc p15, 3, %0, c15, c0, 7 @ l2cpdr" : "=r" (val));
+
+ raw_spin_unlock_irqrestore(&krait_l2_lock, flags);
+
+ return val;
+}
+EXPORT_SYMBOL(krait_get_l2_indirect_reg);
diff --git a/arch/arm/include/asm/krait-l2-accessors.h b/arch/arm/include/asm/krait-l2-accessors.h
new file mode 100644
index 0000000..5041625
--- /dev/null
+++ b/arch/arm/include/asm/krait-l2-accessors.h
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#ifndef __ASMARM_KRAIT_L2_ACCESSORS_H
+#define __ASMARM_KRAIT_L2_ACCESSORS_H
+
+extern void krait_set_l2_indirect_reg(u32 addr, u32 val);
+extern u32 krait_get_l2_indirect_reg(u32 addr);
+
+#endif
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related
* [PATCH v5 00/15] Krait clocks + Krait CPUfreq
From: Sricharan R @ 2017-12-19 15:54 UTC (permalink / raw)
To: robh+dt, mark.rutland, mturquette, sboyd, linux, andy.gross,
david.brown, rjw, viresh.kumar, linux-arm-kernel, devicetree,
linux-kernel, linux-clk, linux-arm-msm, linux-soc, linux-pm
Cc: sricharan
[v5]
* Addressed comments from Rob for bindings
* Addressed comments from Viresh to use dev_pm_opp_set_prop_name, accordingly
dropped patch #12 and corrected patch #11 from previous patch set in [4]
* Converted to use #spdx tags for newly introduced files
Mostly a resend of the v3 posted by Stephen quite some time back [1]
except for few changes.
Based on reading some feedback from list,
* Dropped the patch "clk: Add safe switch hook" from v3 [2].
Now this is taken care by patch#10 in this series only for Krait.
* Dropped the path "clk: Avoid sending high rates to downstream
clocks during set_rate" from v3 [3].
* Rebased on top of clk-next.
* Dropped the DT update from the series. Will send seperately
* Now with cpufreq-dt+opp supporting voltage scaling, registering the
krait cpu supplies in DT should be sufficient. But one issue is,
the qcom-cpufreq drivers reads the efuse and based on that registers
the opp data and then registers the cpufreq-dt device. So when
cpufreq-dt driver probes and registers the regulator to the OPP framework,
it expects that the opp data for the device should not be registered before
the regulator. Will send a RFC patch removing that check, to find out the
right way of doing it.
These patches provide cpufreq scaling on devices with Krait CPUs.
In Krait CPU designs there's one PLL and two muxes per CPU, allowing
us to switch CPU frequencies independently.
secondary
+-----+ +
| QSB |-------+------------|\
+-----+ | | |-+
| +-------|/ |
| | + |
+-----+ | | |
| PLL |----+-------+ | primary
+-----+ | | | +
| | +-----|\ +------+
+-------+ | | | \ | |
| HFPLL |----------+-----------------| |-----| CPU0 |
+-------+ | | | | | | |
| | | +-----+ | / +------+
| | +-| / 2 |---------|/
| | +-----+ +
| | secondary
| | +
| +------------|\
| | |-+
+---------------|/ | primary
+ | +
+-----|\ +------+
+-------+ | \ | |
| HFPLL |----------------------------| |-----| CPU1 |
+-------+ | | | | |
| +-----+ | / +------+
+-| / 2 |---------|/
+-----+ +
To support this in the common clock framework we model the muxes,
dividers, and PLLs as different clocks. CPUfreq only interacts
with the primary mux (farthest right in the diagram). When CPUfreq
sets a rate, the mux code finds the best parent that can provide the rate.
Due to the design, QSB and the top PLL are always a fixed rate and thus
only support one frequency each. These sources provide the lowest
frequencies for the CPUs. The HFPLLs are where we can make the CPU go
faster (GHz range). Sometimes we need to run the HFPLL twice as
fast and divide it by two to get a particular frequency.
When switching rates we can't leave the CPU clocked by the HFPLL because
we need to turn off the output of the PLL when changing its frequency.
This means we have to switch over to the secondary mux and use one of the
fixed sources. This is why we need something like the safe parent patch.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332607.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332615.html
[3] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/332608.html
[4] https://lwn.net/Articles/740994/
Sricharan R (1):
clk: qcom: Add safe switch hook for krait mux clocks
Stephen Boyd (14):
ARM: Add Krait L2 register accessor functions
clk: mux: Split out register accessors for reuse
clk: qcom: Add support for High-Frequency PLLs (HFPLLs)
clk: qcom: Add HFPLL driver
devicetree: bindings: Document qcom,hfpll
clk: qcom: Add MSM8960/APQ8064's HFPLLs
clk: qcom: Add IPQ806X's HFPLLs
clk: qcom: Add support for Krait clocks
clk: qcom: Add KPSS ACC/GCC driver
devicetree: bindings: Document qcom,kpss-gcc
clk: qcom: Add Krait clock controller driver
devicetree: bindings: Document qcom,krait-cc
cpufreq: Add module to register cpufreq on Krait CPUs
devicetree: bindings: Document qcom,pvs
.../devicetree/bindings/arm/msm/qcom,kpss-acc.txt | 7 +
.../devicetree/bindings/arm/msm/qcom,kpss-gcc.txt | 32 ++
.../devicetree/bindings/arm/msm/qcom,pvs.txt | 91 +++++
.../devicetree/bindings/clock/qcom,hfpll.txt | 46 +++
.../devicetree/bindings/clock/qcom,krait-cc.txt | 22 ++
arch/arm/common/Kconfig | 3 +
arch/arm/common/Makefile | 1 +
arch/arm/common/krait-l2-accessors.c | 48 +++
arch/arm/include/asm/krait-l2-accessors.h | 10 +
drivers/clk/clk-mux.c | 75 ++--
drivers/clk/qcom/Kconfig | 28 ++
drivers/clk/qcom/Makefile | 5 +
drivers/clk/qcom/clk-hfpll.c | 244 +++++++++++++
drivers/clk/qcom/clk-hfpll.h | 45 +++
drivers/clk/qcom/clk-krait.c | 126 +++++++
drivers/clk/qcom/clk-krait.h | 41 +++
drivers/clk/qcom/gcc-ipq806x.c | 82 +++++
drivers/clk/qcom/gcc-msm8960.c | 172 +++++++++
drivers/clk/qcom/hfpll.c | 96 +++++
drivers/clk/qcom/kpss-xcc.c | 87 +++++
drivers/clk/qcom/krait-cc.c | 397 +++++++++++++++++++++
drivers/cpufreq/Kconfig.arm | 9 +
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +-
drivers/cpufreq/qcom-cpufreq.c | 171 +++++++++
include/dt-bindings/clock/qcom,gcc-msm8960.h | 2 +
include/linux/clk-provider.h | 9 +-
27 files changed, 1822 insertions(+), 31 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,kpss-gcc.txt
create mode 100644 Documentation/devicetree/bindings/arm/msm/qcom,pvs.txt
create mode 100644 Documentation/devicetree/bindings/clock/qcom,hfpll.txt
create mode 100644 Documentation/devicetree/bindings/clock/qcom,krait-cc.txt
create mode 100644 arch/arm/common/krait-l2-accessors.c
create mode 100644 arch/arm/include/asm/krait-l2-accessors.h
create mode 100644 drivers/clk/qcom/clk-hfpll.c
create mode 100644 drivers/clk/qcom/clk-hfpll.h
create mode 100644 drivers/clk/qcom/clk-krait.c
create mode 100644 drivers/clk/qcom/clk-krait.h
create mode 100644 drivers/clk/qcom/hfpll.c
create mode 100644 drivers/clk/qcom/kpss-xcc.c
create mode 100644 drivers/clk/qcom/krait-cc.c
create mode 100644 drivers/cpufreq/qcom-cpufreq.c
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply
* [PATCH 6/6] ARM: imx_v6_v7_defconfig: Enable Dialog Semicondocter DA9062 driver
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, robh+dt, Stefan Riedmueller,
linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
The phyCORE-i.MX 6 uses the DA9062/63 PMIC, RTC and Watchdog driver.
Enable this option by default.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/configs/imx_v6_v7_defconfig | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 6726c83..e3c4163 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -216,8 +216,10 @@ CONFIG_THERMAL_WRITABLE_TRIPS=y
CONFIG_CPU_THERMAL=y
CONFIG_IMX_THERMAL=y
CONFIG_WATCHDOG=y
+CONFIG_DA9062_WATCHDOG=y
CONFIG_IMX2_WDT=y
CONFIG_MFD_DA9052_I2C=y
+CONFIG_MFD_DA9062=y
CONFIG_MFD_MC13XXX_SPI=y
CONFIG_MFD_MC13XXX_I2C=y
CONFIG_MFD_STMPE=y
@@ -225,6 +227,7 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_ANATOP=y
CONFIG_REGULATOR_DA9052=y
+CONFIG_REGULATOR_DA9062=y
CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_MC13783=y
CONFIG_REGULATOR_MC13892=y
@@ -348,6 +351,7 @@ CONFIG_RTC_DRV_ISL1208=y
CONFIG_RTC_DRV_PCF8523=y
CONFIG_RTC_DRV_PCF8563=y
CONFIG_RTC_DRV_M41T80=y
+CONFIG_RTC_DRV_DA9063=y
CONFIG_RTC_DRV_MC13XXX=y
CONFIG_RTC_DRV_MXC=y
CONFIG_RTC_DRV_SNVS=y
--
2.7.4
^ permalink raw reply related
* [PATCH 5/6] ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, Stefan Riedmueller, Enrico Scholz,
Stefan Lengfeld, robh+dt, Christian Hemp, linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
From: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 76 +++++++++++++++++++++++
2 files changed, 77 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 07d99a1..d42b522 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -479,6 +479,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-zii-rdu2.dtb \
imx6qp-nitrogen6_max.dtb \
imx6qp-nitrogen6_som2.dtb \
+ imx6qp-phytec-mira-rdk-nand.dtb \
imx6qp-sabreauto.dtb \
imx6qp-sabresd.dtb \
imx6qp-tx6qp-8037.dtb \
diff --git a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..397871c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Mira QuadPlus Carrier-Board with NAND";
+ compatible = "phytec,imx6qp-pbac06-nand", "phytec,imx6qp-pbac06",
+ "phytec,imx6qdl-pcm058", "fsl,imx6qp";
+
+ aliases {
+ ipu1 = &ipu2;
+ };
+
+ chosen {
+ linux,stdout-path = &uart2;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&flash {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related
* [PATCH 4/6] ARM: dts: imx6: Add support for phxBOARD-Mira i.MX 6 DualLight/Solo RDK
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, Stefan Riedmueller, robh+dt,
Christian Hemp, Stefan Christ, linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
From: Christian Hemp <c.hemp@phytec.de>
Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.
Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 +++++++++++++++++++++++
2 files changed, 65 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b793617..07d99a1 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -388,6 +388,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-icore-rqs.dtb \
imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
+ imx6dl-phytec-mira-rdk-nand.dtb \
imx6dl-phytec-pbab01.dtb \
imx6dl-rex-basic.dtb \
imx6dl-riotboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..f56c20f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Mira DualLite/Solo Carrier-Board with NAND";
+ compatible = "phytec,imx6dl-pbac06-nand", "phytec,imx6dl-pbac06",
+ "phytec,imx6qdl-pcm058", "fsl,imx6dl";
+
+ chosen {
+ linux,stdout-path = &uart2;
+ };
+};
+
+ðphy {
+ max-speed = <100>;
+};
+
+&fec {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related
* [PATCH 3/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, Stefan Riedmueller, robh+dt,
Christian Hemp, Stefan Christ, linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
From: Christian Hemp <c.hemp@phytec.de>
Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.
Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 76 ++++++++++++++++++++++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 76 ++++++++++++++++++++++++
3 files changed, 154 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d0381e9..b793617 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -449,6 +449,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-nitrogen6_max.dtb \
imx6q-nitrogen6_som2.dtb \
imx6q-novena.dtb \
+ imx6q-phytec-mira-rdk-emmc.dtb \
+ imx6q-phytec-mira-rdk-nand.dtb \
imx6q-phytec-pbab01.dtb \
imx6q-pistachio.dtb \
imx6q-rex-pro.dtb \
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
new file mode 100644
index 0000000..6e6f694
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with eMMC";
+ compatible = "phytec,imx6q-pbac06-emmc", "phytec,imx6q-pbac06",
+ "phytec,imx6qdl-pcm058", "fsl,imx6q";
+
+ aliases {
+ ipu1 = &ipu2;
+ };
+
+ chosen {
+ linux,stdout-path = &uart2;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&flash {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
+
+&usdhc4 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
new file mode 100644
index 0000000..6145e8e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-phytec-phycore-som.dtsi"
+#include "imx6qdl-phytec-mira.dtsi"
+
+/ {
+ model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND";
+ compatible = "phytec,imx6q-pbac06-nand", "phytec,imx6q-pbac06",
+ "phytec,imx6qdl-pcm058", "fsl,imx6q";
+
+ aliases {
+ ipu1 = &ipu2;
+ };
+
+ chosen {
+ linux,stdout-path = &uart2;
+ };
+};
+
+&can1 {
+ status = "okay";
+};
+
+&fec {
+ status = "okay";
+};
+
+&flash {
+ status = "okay";
+};
+
+&gpmi {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&i2c_rtc {
+ status = "okay";
+};
+
+&pcie {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ status = "okay";
+};
+
+&usdhc1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related
* [PATCH 2/6] ARM: dts: imx6: Add initial support for phyBOARD-Mira
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, Stefan Riedmueller, Christoph Fritz,
robh+dt, Christian Hemp, Stefan Christ, linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
This patch adds basic support for PHYTEC phyBOARD-Mira as carrier board
for PHYTEC phyCORE-i.MX 6.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 +++++++++++++++++++++++++++++
1 file changed, 390 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
new file mode 100644
index 0000000..b7d7542
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
@@ -0,0 +1,390 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+
+/ {
+ aliases {
+ rtc0 = &i2c_rtc;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ power-supply = <®_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ status = "okay";
+ };
+
+ gpio_leds: leds {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds>;
+ status = "disabled";
+
+ compatible = "gpio-leds";
+
+ red {
+ label = "phyboard-mira:red";
+ gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ green {
+ label = "phyboard-mira:green";
+ gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "phyboard-mira:blue";
+ gpios = <&gpio5 24 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ reg_backlight: regulator-backlight {
+ compatible = "regulator-fixed";
+ regulator-name = "backlight_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_en_switch: regulator-en-switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_en_switch>;
+ compatible = "regulator-fixed";
+ regulator-name = "Enable Switch";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ };
+
+ reg_flexcan1: regulator-flexcan1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1_en>;
+ compatible = "regulator-fixed";
+ regulator-name = "flexcan1-reg";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_panel: regulator-panel {
+ compatible = "regulator-fixed";
+ regulator-name = "panel-power-supply";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ reg_pcie: regulator-pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie_reg>;
+ compatible = "regulator-fixed";
+ regulator-name = "mPCIe_1V5";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ gpio = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+ regulator-always-on;
+ enable-active-high;
+ };
+
+ reg_usb_h1_vbus: usb-h1-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh1_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio2 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbotg_vbus: usbotg-vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg_vbus>;
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ panel {
+ compatible = "auo,g104sn02";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_panel_en>;
+ power-supply = <®_panel>;
+ enable-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+
+ backlight = <&backlight>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_flexcan1>;
+ status = "disabled";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmicec>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "disabled";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ clock-frequency = <400000>;
+ status = "disabled";
+
+ stmpe: touchctrl@44 {
+ compatible = "st,stmpe811";
+ reg = <0x44>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <12 IRQ_TYPE_NONE>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_stmpe>;
+ status = "disabled";
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ st,sample-time = <4>;
+ st,mod-12b = <1>;
+ st,ref-sel = <0>;
+ st,adc-freq = <1>;
+ st,ave-ctrl = <1>;
+ st,touch-det-delay = <2>;
+ st,settling = <2>;
+ st,fraction-z = <7>;
+ st,i-drive = <1>;
+ };
+ };
+
+ i2c_rtc: rtc@68 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc_int>;
+ compatible = "mc,rv4162";
+ reg = <0x68>;
+ interrupt-parent = <&gpio7>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ clock-frequency = <100000>;
+ status = "disabled";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ fsl,data-mapping = "spwg";
+ fsl,data-width = <24>;
+ status = "disabled";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "disabled";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ disable-over-current;
+ status = "disabled";
+};
+
+&usbotg {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ vbus-supply = <®_usbotg_vbus>;
+ disable-over-current;
+ status = "disabled";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_panel_en: panelen1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0xb0b1
+ >;
+ };
+
+ pinctrl_en_switch: enswitchgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_DA4__GPIO3_IO04 0xb0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
+ MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan1_en: flexcan1engrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A18__GPIO2_IO20 0xb0b1
+ >;
+ };
+
+ pinctrl_gpioleds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__GPIO5_IO24 0x1b0b0
+ >;
+ };
+
+ pinctrl_hdmicec: hdmicecgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__GPIO2_IO25 0xb0b1
+ >;
+ };
+
+ pinctrl_pcie_reg: pciereggrp {
+ fsl,pins = <MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0xb0b1>;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_rtc_int: rtcintgrp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0
+ >;
+ };
+
+ pinctrl_stmpe: stmpegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_EB3__UART3_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbh1_vbus: usbh1vbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A20__GPIO2_IO18 0xb0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_usbotg_vbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A19__GPIO2_IO19 0xb0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb0b1 /* CD */
+ >;
+ };
+};
--
2.7.4
^ permalink raw reply related
* [PATCH 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, Stefan Riedmueller, Christoph Fritz,
robh+dt, Christian Hemp, Stefan Christ, linux-arm-kernel
In-Reply-To: <1513698588-13325-1-git-send-email-s.riedmueller@phytec.de>
This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
6Quad/Dual or i.MX 6DualLight/Solo.
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
---
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++
1 file changed, 282 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
new file mode 100644
index 0000000..5283f0d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2017 PHYTEC Messtechnik GmbH
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "PHYTEC phyCORE-i.MX 6";
+ compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl";
+
+ aliases {
+ ipu0 = &ipu1;
+ rtc1 = &da9062_rtc;
+ rtc2 = &snvs_rtc;
+ };
+
+ /*
+ * Set the minimum memory size here and
+ * let the bootloader set the real size.
+ */
+ memory {
+ reg = <0x10000000 0x8000000>;
+ };
+
+ gpio_leds_som: somleds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioleds_som>;
+
+ som_green {
+ label = "phycore:green";
+ gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ flash: flash@0 {
+ compatible = "m25p80";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ status = "disabled";
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-handle = <ðphy>;
+ phy-mode = "rgmii";
+ phy-supply = <&vdd_eth_io>;
+ phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ status = "disabled";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@3 {
+ reg = <3>;
+ txc-skew-ps = <1680>;
+ rxc-skew-ps = <1860>;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ nand-on-flash-bbt;
+ status = "disabled";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ eeprom: eeprom@50 {
+ compatible = "cat,24c32";
+ reg = <0x50>;
+ };
+
+ pmic0: pmic@58 {
+ compatible = "dlg,da9062";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+
+ da9062_rtc: rtc {
+ compatible = "dlg,da9062-rtc";
+ };
+
+ da9062_wdt: watchdog {
+ compatible = "dlg,da9062-watchdog";
+ };
+
+ da9062_reg: regulators {
+ vdd_arm: buck1 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_soc: buck2 {
+ regulator-name = "vdd_soc";
+ regulator-min-microvolt = <730000>;
+ regulator-max-microvolt = <1380000>;
+ regulator-always-on;
+ };
+
+ vdd_ddr3_1p5: buck3 {
+ regulator-name = "vdd_ddr3";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_1p2: buck4 {
+ regulator-name = "vdd_eth";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vdd_snvs: ldo1 {
+ regulator-name = "vdd_snvs";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_high: ldo2 {
+ regulator-name = "vdd_high";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vdd_eth_io: ldo3 {
+ regulator-name = "vdd_eth_io";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vdd_emmc_1p8: ldo4 {
+ regulator-name = "vdd_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+};
+
+®_arm {
+ vin-supply = <&vdd_arm>;
+};
+
+®_pu {
+ vin-supply = <&vdd_soc>;
+};
+
+®_soc {
+ vin-supply = <&vdd_soc>;
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ non-removable;
+ vmmc-supply = <&vdd_emmc_1p8>;
+ status = "disabled";
+};
+
+&iomuxc {
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpioleds_som: gpioledssomgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS2__NAND_CE2_B 0xb0b1
+ MX6QDL_PAD_NANDF_CS3__NAND_CE3_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b0
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc4: usdhc4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059
+ MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059
+ MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059
+ MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059
+ MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059
+ MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059
+ MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059
+ MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059
+ MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059
+ MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059
+ >;
+ };
+};
--
2.7.4
^ permalink raw reply related
* [PATCH 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support
From: Stefan Riedmueller @ 2017-12-19 15:49 UTC (permalink / raw)
To: shawnguo, kernel, fabio.estevam
Cc: mark.rutland, devicetree, robh+dt, Stefan Riedmueller,
linux-arm-kernel
This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira.
Following boards are included:
phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with:
- i.MX 6Quad/Dual SOC
- NAND or eMMC
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with:
- i.MX 6DualLight/Solo
- NAND
- HDMI interface
- 100 MBit/s Ethernet
- USB Host
- RS232
phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with:
- i.MX 6QuadPlus SOC
- NAND
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
The entire series is based on v4.15-rc4.
Christian Hemp (2):
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
ARM: dts: imx6: Add support for phxBOARD-Mira i.MX 6 DualLight/Solo
RDK
Enrico Scholz (1):
ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
Stefan Riedmueller (3):
ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
ARM: dts: imx6: Add initial support for phyBOARD-Mira
ARM: imx_v6_v7_defconfig: Enable Dialog Semicondocter DA9062 driver
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 ++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 76 +++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 76 +++++
arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 ++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++
arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 76 +++++
arch/arm/configs/imx_v6_v7_defconfig | 4 +
8 files changed, 972 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
--
2.7.4
^ permalink raw reply
* Re: [PATCH V2 3/9] ARM: stm32: prepare stm32 family to welcome armv7 architecture
From: Arnd Bergmann @ 2017-12-19 15:26 UTC (permalink / raw)
To: Ludovic BARRE
Cc: Russell King, Rob Herring, Linus Walleij, Maxime Coquelin,
Alexandre Torgue, Gerald Baeza, Linux ARM,
Linux Kernel Mailing List, DTML
In-Reply-To: <45e2f530-1e72-6933-4367-95aadd709873-qxv4g6HH51o@public.gmane.org>
On Tue, Dec 19, 2017 at 3:43 PM, Ludovic BARRE <ludovic.barre-qxv4g6HH51o@public.gmane.org> wrote:
>
>
> On 12/18/2017 09:24 PM, Arnd Bergmann wrote:
>>
>> On Mon, Dec 18, 2017 at 4:17 PM, Ludovic Barre <ludovic.Barre-qxv4g6HH51o@public.gmane.org>
>> wrote:
>>>
>>> From: Ludovic Barre <ludovic.barre-qxv4g6HH51o@public.gmane.org>
>>>
>>> This patch prepares the STM32 machine for the integration of Cortex-A
>>> based microprocessor (MPU), on top of the existing Cortex-M
>>> microcontroller family (MCU). Since both MCUs and MPUs are sharing
>>> common hardware blocks we can keep using ARCH_STM32 flag for most of
>>> them. If a hardware block is specific to one family we can use either
>>> ARM_SINGLE_ARMV7M or ARCH_MULTI_V7 flag.
>>>
>>> Signed-off-by: Ludovic Barre <ludovic.barre-qxv4g6HH51o@public.gmane.org>
>>
>>
>> Looks good overall. Two more small comments:
>>
>>
>>>
>>> +if ARCH_STM32
>>> +
>>> config MACH_STM32F429
>>> - bool "STMicrolectronics STM32F429"
>>> - depends on ARCH_STM32
>>> + bool "STMicroelectronics STM32F429"
>>> + depends on ARM_SINGLE_ARMV7M
>>> default y
>>
>>
>> Instead of the explicit dependency for each board, I'd leave the
>> surrounding
>> 'if ARM_SINGLE_ARMV7M'. I think you had in v1.
>
>
> As you suggest, I follow mach-at91 example.
> The point is on "depends on ARM_SINGLE_ARMV7M" ?
> You prefer this way:
> config MACH_STM32F429
> bool "STMicroelectronics STM32F429" if ARM_SINGLE_ARMV7M
> default y
>
No, that would be wrong, that way you would always enable
MACH_STM32F429 when ARM_SINGLE_ARMV7M is turned
off, which is exactly the wrong way round. What I meant is
if ARCH_STM32
if ARM_SINGLE_ARMV7M
config MACH_STM32F429
bool "STMicrolectronics STM32F429"
config MACH_STM32...
...
endif # ARMv7-M
if ARCH_MULTI_V7
config MACH_STM32...
...
endif # ARMv7-A
endif # STM32
Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply
* [PATCH 8/8] ARM: dts: am572x-idk: Add cpu0 vdd supply
From: Dave Gerlach @ 2017-12-19 15:24 UTC (permalink / raw)
To: Tony Lindgren
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Nishanth Menon, Dave Gerlach
In-Reply-To: <1513697066-27732-1-git-send-email-d-gerlach-l0cyMroinI0@public.gmane.org>
Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach-l0cyMroinI0@public.gmane.org>
---
arch/arm/boot/dts/am572x-idk.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/am572x-idk.dts b/arch/arm/boot/dts/am572x-idk.dts
index a578fe97ba3b..d0daf48346ab 100644
--- a/arch/arm/boot/dts/am572x-idk.dts
+++ b/arch/arm/boot/dts/am572x-idk.dts
@@ -127,3 +127,7 @@
status = "okay";
};
};
+
+&cpu0 {
+ vdd-supply = <&smps12_reg>;
+};
--
2.15.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
* [PATCH 7/8] ARM: dts: am571x-idk: Add cpu0 vdd supply
From: Dave Gerlach @ 2017-12-19 15:24 UTC (permalink / raw)
To: Tony Lindgren
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-omap-u79uwXL29TY76Z2rM5mHXA,
devicetree-u79uwXL29TY76Z2rM5mHXA, Nishanth Menon, Dave Gerlach
In-Reply-To: <1513697066-27732-1-git-send-email-d-gerlach-l0cyMroinI0@public.gmane.org>
Add vdd-supply as smps12_reg for cpu0.
Signed-off-by: Dave Gerlach <d-gerlach-l0cyMroinI0@public.gmane.org>
---
arch/arm/boot/dts/am571x-idk.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/am571x-idk.dts b/arch/arm/boot/dts/am571x-idk.dts
index debf9464403e..6d3c83743156 100644
--- a/arch/arm/boot/dts/am571x-idk.dts
+++ b/arch/arm/boot/dts/am571x-idk.dts
@@ -117,3 +117,7 @@
pinctrl-1 = <&mmc2_pins_hs>;
pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
};
+
+&cpu0 {
+ vdd-supply = <&smps12_reg>;
+};
--
2.15.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox