* Re: [PATCH 2/2] dt-bindings: leds: document new "power-supply" property
From: Rob Herring @ 2019-07-24 16:47 UTC (permalink / raw)
To: Jean-Jacques Hiblot
Cc: jacek.anaszewski, pavel, mark.rutland, daniel.thompson, dmurphy,
linux-leds, linux-kernel, devicetree
In-Reply-To: <20190708103547.23528-3-jjhiblot@ti.com>
On Mon, Jul 08, 2019 at 12:35:47PM +0200, Jean-Jacques Hiblot wrote:
> Most of the LEDs are powered by a voltage/current regulator. describing in
> the device-tree makes it possible for the LED core to enable/disable it
> when needed.
>
> Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
> ---
> Documentation/devicetree/bindings/leds/common.txt | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt
> index 70876ac11367..e093a2b7eb90 100644
> --- a/Documentation/devicetree/bindings/leds/common.txt
> +++ b/Documentation/devicetree/bindings/leds/common.txt
> @@ -61,6 +61,11 @@ Optional properties for child nodes:
> - panic-indicator : This property specifies that the LED should be used,
> if at all possible, as a panic indicator.
>
> +- power-supply : A voltage/current regulator used to to power the LED. When a
> + LED is turned off, the LED core disable its regulator. The
> + same regulator can power many LED (or other) devices. It is
> + turned off only when all of its users disabled it.
Not sure this should be common. It wouldn't apply to cases where we have
an LED controller parent nor gpio and pwm LEDs and those are most cases.
Perhaps what makes sense here is an regulator-led binding.
> +
> - trigger-sources : List of devices which should be used as a source triggering
> this LED activity. Some LEDs can be related to a specific
> device and should somehow indicate its state. E.g. USB 2.0
> --
> 2.17.1
>
^ permalink raw reply
* Re: [RFC PATCH V2 1/6] dt-bindings: mt8183: Added DIP dt-bindings
From: Rob Herring @ 2019-07-24 16:49 UTC (permalink / raw)
Cc: laurent.pinchart+renesas, Rynn.Wu, Allan.Yang, suleiman,
Jerry-ch.Chen, jungo.lin, hans.verkuil, frederic.chen,
linux-media, devicetree, holmes.chiou, shik, yuzhao,
linux-mediatek, matthias.bgg, mchehab, linux-arm-kernel,
Sean.Cheng, srv_heupstream, sj.huang, tfiga, christie.yu, zwisler
In-Reply-To: <20190708110500.7242-2-frederic.chen@mediatek.com>
On Mon, 8 Jul 2019 19:04:55 +0800, <frederic.chen@mediatek.com> wrote:
> From: Frederic Chen <frederic.chen@mediatek.com>
>
> This patch adds DT binding documentation for the Digital Image
> Processing (DIP) unit of camera ISP system on Mediatek's SoCs.
>
> It depends on the SCP and MDP 3 patch as following:
>
> 1. dt-bindings: Add a binding for Mediatek SCP
> https://patchwork.kernel.org/patch/11027247/
> 2. dt-binding: mt8183: Add Mediatek MDP3 dt-bindings
> https://patchwork.kernel.org/patch/10945603/
>
> Signed-off-by: Frederic Chen <frederic.chen@mediatek.com>
> ---
> .../bindings/media/mediatek,mt8183-dip.txt | 40 +++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/mediatek,mt8183-dip.txt
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply
* Re: [PATCH v12 6/9] ARM: dts: exynos: add chipid label and syscon compatible
From: Krzysztof Kozlowski @ 2019-07-24 17:10 UTC (permalink / raw)
To: Lukasz Luba
Cc: devicetree, linux-kernel, linux-pm, linux-samsung-soc, linux-clk,
mturquette, sboyd, b.zolnierkie, kgene, mark.rutland, robh+dt,
cw00.choi, kyungmin.park, m.szyprowski, s.nawrocki, myungjoo.ham,
keescook, tony, jroedel, treding, digetx, gregkh,
willy.mh.wolff.ml
In-Reply-To: <20190722094646.13342-7-l.luba@partner.samsung.com>
On Mon, Jul 22, 2019 at 11:46:43AM +0200, Lukasz Luba wrote:
> Add the chipid label which allows to use it in phandle from other device.
> Use syscon in compatible to get the regmap of the device register set.
> The chipid is used in DMC during initialization to compare compatibility.
>
I cannot find its usage in DMC driver.
Best regards,
Krzysztof
> Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
> ---
> arch/arm/boot/dts/exynos5.dtsi | 4 ++--
> 1 file changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
> index 67f9b4504a42..4801ca759feb 100644
> --- a/arch/arm/boot/dts/exynos5.dtsi
> +++ b/arch/arm/boot/dts/exynos5.dtsi
> @@ -35,8 +35,8 @@
> #size-cells = <1>;
> ranges;
>
> - chipid@10000000 {
> - compatible = "samsung,exynos4210-chipid";
> + chipid: chipid@10000000 {
> + compatible = "samsung,exynos4210-chipid", "syscon";
> reg = <0x10000000 0x100>;
> };
>
> --
> 2.17.1
>
^ permalink raw reply
* [PATCH v15 00/13] TCU patchset v15
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre
Hi,
This is the V15 of my Ingenic TCU patchet.
The big change since V14 is that the custom MFD driver
(ex patch 04/13) was dropped in favor of a small patch to syscon
and a "simple-mfd" compatible.
The patchset was based on mips/mips-next, but all of them minus
the last one will apply cleanly on v5.3-rc1.
Changelog:
* [02/13]: Remove info about MFD driver
* [03/13]: Add "simple-mfd" compatible string
* [04/13]: New patch
* [05/13]: - Use CLK_OF_DECLARE_DRIVER since we use "simple-mfd"
- Use device_node_to_regmap()
* [06/13]: Use device_node_to_regmap()
* [07/13]: Use device_node_to_regmap()
* [09/13]: Add "simple-mfd" compatible string
Cheers,
-Paul
^ permalink raw reply
* [PATCH v15 01/13] dt-bindings: ingenic: Add DT bindings for TCU clocks
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek, Rob Herring
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
This header provides clock numbers for the ingenic,tcu
DT binding.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
---
Notes:
v2: Use SPDX identifier for the license
v3/v4: No change
v5: s/JZ47*_/TCU_/ and dropped *_CLK_LAST defines
v6-v15: No change
include/dt-bindings/clock/ingenic,tcu.h | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
create mode 100644 include/dt-bindings/clock/ingenic,tcu.h
diff --git a/include/dt-bindings/clock/ingenic,tcu.h b/include/dt-bindings/clock/ingenic,tcu.h
new file mode 100644
index 000000000000..d569650a7945
--- /dev/null
+++ b/include/dt-bindings/clock/ingenic,tcu.h
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides clock numbers for the ingenic,tcu DT binding.
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_INGENIC_TCU_H__
+#define __DT_BINDINGS_CLOCK_INGENIC_TCU_H__
+
+#define TCU_CLK_TIMER0 0
+#define TCU_CLK_TIMER1 1
+#define TCU_CLK_TIMER2 2
+#define TCU_CLK_TIMER3 3
+#define TCU_CLK_TIMER4 4
+#define TCU_CLK_TIMER5 5
+#define TCU_CLK_TIMER6 6
+#define TCU_CLK_TIMER7 7
+#define TCU_CLK_WDT 8
+#define TCU_CLK_OST 9
+
+#endif /* __DT_BINDINGS_CLOCK_INGENIC_TCU_H__ */
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 02/13] doc: Add doc for the Ingenic TCU hardware
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
Add documentation about the Timer/Counter Unit (TCU) present in the
Ingenic JZ47xx SoCs.
The Timer/Counter Unit (TCU) in Ingenic JZ47xx SoCs is a multi-function
hardware block. It features up to to eight channels, that can be used as
counters, timers, or PWM.
- JZ4725B, JZ4750, JZ4755 only have six TCU channels. The other SoCs all
have eight channels.
- JZ4725B introduced a separate channel, called Operating System Timer
(OST). It is a 32-bit programmable timer. On JZ4770 and above, it is
64-bit.
- Each one of the TCU channels has its own clock, which can be reparented
to three different clocks (pclk, ext, rtc), gated, and reclocked, through
their TCSR register.
* The watchdog and OST hardware blocks also feature a TCSR register with
the same format in their register space.
* The TCU registers used to gate/ungate can also gate/ungate the watchdog
and OST clocks.
- Each TCU channel works in one of two modes:
* mode TCU1: channels cannot work in sleep mode, but are easier to
operate.
* mode TCU2: channels can work in sleep mode, but the operation is a bit
more complicated than with TCU1 channels.
- The mode of each TCU channel depends on the SoC used:
* On the oldest SoCs (up to JZ4740), all of the eight channels operate in
TCU1 mode.
* On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
* On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
others operate as TCU1.
- Each channel can generate an interrupt. Some channels share an interrupt
line, some don't, and this changes between SoC versions:
* on older SoCs (JZ4740 and below), channel 0 and channel 1 have their
own interrupt line; channels 2-7 share the last interrupt line.
* On JZ4725B, channel 0 has its own interrupt; channels 1-5 share one
interrupt line; the OST uses the last interrupt line.
* on newer SoCs (JZ4750 and above), channel 5 has its own interrupt;
channels 0-4 and (if eight channels) 6-7 all share one interrupt line;
the OST uses the last interrupt line.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v4: New patch in this series
v5: Added information about number of channels, and improved
documentation about channel modes
v6: Add info about OST (can be 32-bit on older SoCs)
v7-v11: No change
v12: Add details about new implementation
v13: No change
v14: Convert to ReStructured Text
v15: Remove info about MFD driver
Documentation/index.rst | 1 +
Documentation/mips/index.rst | 11 +++++
Documentation/mips/ingenic-tcu.rst | 71 ++++++++++++++++++++++++++++++
3 files changed, 83 insertions(+)
create mode 100644 Documentation/mips/index.rst
create mode 100644 Documentation/mips/ingenic-tcu.rst
diff --git a/Documentation/index.rst b/Documentation/index.rst
index 70ae148ec980..87214feda41f 100644
--- a/Documentation/index.rst
+++ b/Documentation/index.rst
@@ -143,6 +143,7 @@ implementation.
arm64/index
ia64/index
m68k/index
+ mips/index
riscv/index
s390/index
sh/index
diff --git a/Documentation/mips/index.rst b/Documentation/mips/index.rst
new file mode 100644
index 000000000000..321b4794f3b8
--- /dev/null
+++ b/Documentation/mips/index.rst
@@ -0,0 +1,11 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===========================
+MIPS-specific Documentation
+===========================
+
+.. toctree::
+ :maxdepth: 1
+ :numbered:
+
+ ingenic-tcu
diff --git a/Documentation/mips/ingenic-tcu.rst b/Documentation/mips/ingenic-tcu.rst
new file mode 100644
index 000000000000..c4ef4c45aade
--- /dev/null
+++ b/Documentation/mips/ingenic-tcu.rst
@@ -0,0 +1,71 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===============================================
+Ingenic JZ47xx SoCs Timer/Counter Unit hardware
+===============================================
+
+The Timer/Counter Unit (TCU) in Ingenic JZ47xx SoCs is a multi-function
+hardware block. It features up to to eight channels, that can be used as
+counters, timers, or PWM.
+
+- JZ4725B, JZ4750, JZ4755 only have six TCU channels. The other SoCs all
+ have eight channels.
+
+- JZ4725B introduced a separate channel, called Operating System Timer
+ (OST). It is a 32-bit programmable timer. On JZ4760B and above, it is
+ 64-bit.
+
+- Each one of the TCU channels has its own clock, which can be reparented to three
+ different clocks (pclk, ext, rtc), gated, and reclocked, through their TCSR register.
+
+ - The watchdog and OST hardware blocks also feature a TCSR register with the same
+ format in their register space.
+ - The TCU registers used to gate/ungate can also gate/ungate the watchdog and
+ OST clocks.
+
+- Each TCU channel works in one of two modes:
+
+ - mode TCU1: channels cannot work in sleep mode, but are easier to
+ operate.
+ - mode TCU2: channels can work in sleep mode, but the operation is a bit
+ more complicated than with TCU1 channels.
+
+- The mode of each TCU channel depends on the SoC used:
+
+ - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
+ TCU1 mode.
+ - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
+ - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
+ others operate as TCU1.
+
+- Each channel can generate an interrupt. Some channels share an interrupt
+ line, some don't, and this changes between SoC versions:
+
+ - on older SoCs (JZ4740 and below), channel 0 and channel 1 have their
+ own interrupt line; channels 2-7 share the last interrupt line.
+ - On JZ4725B, channel 0 has its own interrupt; channels 1-5 share one
+ interrupt line; the OST uses the last interrupt line.
+ - on newer SoCs (JZ4750 and above), channel 5 has its own interrupt;
+ channels 0-4 and (if eight channels) 6-7 all share one interrupt line;
+ the OST uses the last interrupt line.
+
+Implementation
+==============
+
+The functionalities of the TCU hardware are spread across multiple drivers:
+
+=========== =====
+clocks drivers/clk/ingenic/tcu.c
+interrupts drivers/irqchip/irq-ingenic-tcu.c
+timers drivers/clocksource/ingenic-timer.c
+OST drivers/clocksource/ingenic-ost.c
+PWM drivers/pwm/pwm-jz4740.c
+watchdog drivers/watchdog/jz4740_wdt.c
+=========== =====
+
+Because various functionalities of the TCU that belong to different drivers
+and frameworks can be controlled from the same registers, all of these
+drivers access their registers through the same regmap.
+
+For more information regarding the devicetree bindings of the TCU drivers,
+have a look at Documentation/devicetree/bindings/mfd/ingenic,tcu.txt.
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 03/13] dt-bindings: Add doc for the Ingenic TCU drivers
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Rob Herring, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
Add documentation about how to properly use the Ingenic TCU
(Timer/Counter Unit) drivers from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v4: New patch in this series. Corresponds to V2 patches 3-4-5 with
added content.
v5:
- Edited PWM/watchdog DT bindings documentation to point to the new
document.
- Moved main document to
Documentation/devicetree/bindings/timer/ingenic,tcu.txt
- Updated documentation to reflect the new devicetree bindings.
v6:
- Removed PWM/watchdog documentation files as asked by upstream
- Removed doc about properties that should be implicit
- Removed doc about ingenic,timer-channel /
ingenic,clocksource-channel as they are gone
- Fix WDT clock name in the binding doc
- Fix lengths of register areas in watchdog/pwm nodes
v7: No change
v8:
- Fix address of the PWM node
- Added doc about system timer and clocksource children nodes
v9:
- Remove doc about system timer and clocksource children
nodes...
- Add doc about ingenic,pwm-channels-mask property
v10: No change
v11: Fix info about default value of ingenic,pwm-channels-mask
v12: Drop sub-nodes for now; they will be introduced in a follow-up
patchset.
v13:
- Revert back to v11. Turns out it was okay.
- Remove 'interrupt-parent' of the list of required properties.
v14: No change
v15: Add "simple-mfd" compatible string
.../bindings/pwm/ingenic,jz47xx-pwm.txt | 22 ---
.../devicetree/bindings/timer/ingenic,tcu.txt | 137 ++++++++++++++++++
.../bindings/watchdog/ingenic,jz4740-wdt.txt | 17 ---
3 files changed, 137 insertions(+), 39 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
create mode 100644 Documentation/devicetree/bindings/timer/ingenic,tcu.txt
delete mode 100644 Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
deleted file mode 100644
index 493bec80d59b..000000000000
--- a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
+++ /dev/null
@@ -1,22 +0,0 @@
-Ingenic JZ47xx PWM Controller
-=============================
-
-Required properties:
-- compatible: Should be "ingenic,jz4740-pwm"
-- #pwm-cells: Should be 3. See pwm.txt in this directory for a description
- of the cells format.
-- clocks : phandle to the external clock.
-- clock-names : Should be "ext".
-
-
-Example:
-
- pwm: pwm@10002000 {
- compatible = "ingenic,jz4740-pwm";
- reg = <0x10002000 0x1000>;
-
- #pwm-cells = <3>;
-
- clocks = <&ext>;
- clock-names = "ext";
- };
diff --git a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
new file mode 100644
index 000000000000..5a4b9ddd9470
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
@@ -0,0 +1,137 @@
+Ingenic JZ47xx SoCs Timer/Counter Unit devicetree bindings
+==========================================================
+
+For a description of the TCU hardware and drivers, have a look at
+Documentation/mips/ingenic-tcu.txt.
+
+Required properties:
+
+- compatible: Must be one of:
+ * ingenic,jz4740-tcu
+ * ingenic,jz4725b-tcu
+ * ingenic,jz4770-tcu
+ followed by "simple-mfd".
+- reg: Should be the offset/length value corresponding to the TCU registers
+- clocks: List of phandle & clock specifiers for clocks external to the TCU.
+ The "pclk", "rtc" and "ext" clocks should be provided. The "tcu" clock
+ should be provided if the SoC has it.
+- clock-names: List of name strings for the external clocks.
+- #clock-cells: Should be <1>;
+ Clock consumers specify this argument to identify a clock. The valid values
+ may be found in <dt-bindings/clock/ingenic,tcu.h>.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+ interrupt source. The value should be 1.
+- interrupts : Specifies the interrupt the controller is connected to.
+
+Optional properties:
+
+- ingenic,pwm-channels-mask: Bitmask of TCU channels reserved for PWM use.
+ Default value is 0xfc.
+
+
+Children nodes
+==========================================================
+
+
+PWM node:
+---------
+
+Required properties:
+
+- compatible: Must be one of:
+ * ingenic,jz4740-pwm
+ * ingenic,jz4725b-pwm
+- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of the cell
+ format.
+- clocks: List of phandle & clock specifiers for the TCU clocks.
+- clock-names: List of name strings for the TCU clocks.
+
+
+Watchdog node:
+--------------
+
+Required properties:
+
+- compatible: Must be "ingenic,jz4740-watchdog"
+- clocks: phandle to the WDT clock
+- clock-names: should be "wdt"
+
+
+OS Timer node:
+---------
+
+Required properties:
+
+- compatible: Must be one of:
+ * ingenic,jz4725b-ost
+ * ingenic,jz4770-ost
+- clocks: phandle to the OST clock
+- clock-names: should be "ost"
+- interrupts : Specifies the interrupt the OST is connected to.
+
+
+Example
+==========================================================
+
+#include <dt-bindings/clock/jz4770-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+ tcu: timer@10002000 {
+ compatible = "ingenic,jz4770-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu JZ4770_CLK_RTC
+ &cgu JZ4770_CLK_EXT
+ &cgu JZ4770_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+
+ watchdog: watchdog@0 {
+ compatible = "ingenic,jz4740-watchdog";
+ reg = <0x0 0xc>;
+
+ clocks = <&tcu TCU_CLK_WDT>;
+ clock-names = "wdt";
+ };
+
+ pwm: pwm@40 {
+ compatible = "ingenic,jz4740-pwm";
+ reg = <0x40 0x80>;
+
+ #pwm-cells = <3>;
+
+ clocks = <&tcu TCU_CLK_TIMER0
+ &tcu TCU_CLK_TIMER1
+ &tcu TCU_CLK_TIMER2
+ &tcu TCU_CLK_TIMER3
+ &tcu TCU_CLK_TIMER4
+ &tcu TCU_CLK_TIMER5
+ &tcu TCU_CLK_TIMER6
+ &tcu TCU_CLK_TIMER7>;
+ clock-names = "timer0", "timer1", "timer2", "timer3",
+ "timer4", "timer5", "timer6", "timer7";
+ };
+
+ ost: timer@e0 {
+ compatible = "ingenic,jz4770-ost";
+ reg = <0xe0 0x20>;
+
+ clocks = <&tcu TCU_CLK_OST>;
+ clock-names = "ost";
+
+ interrupts = <15>;
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt b/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
deleted file mode 100644
index ce1cb72d5345..000000000000
--- a/Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt
+++ /dev/null
@@ -1,17 +0,0 @@
-Ingenic Watchdog Timer (WDT) Controller for JZ4740 & JZ4780
-
-Required properties:
-compatible: "ingenic,jz4740-watchdog" or "ingenic,jz4780-watchdog"
-reg: Register address and length for watchdog registers
-clocks: phandle to the RTC clock
-clock-names: should be "rtc"
-
-Example:
-
-watchdog: jz4740-watchdog@10002000 {
- compatible = "ingenic,jz4740-watchdog";
- reg = <0x10002000 0x10>;
-
- clocks = <&cgu JZ4740_CLK_RTC>;
- clock-names = "rtc";
-};
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 04/13] mfd/syscon: Add device_node_to_regmap()
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
device_node_to_regmap() is exactly like syscon_node_to_regmap(), but it
does not check that the node is compatible with "syscon", and won't
attach the first clock it finds to the regmap.
The rationale behind this, is that one device node with a standard
compatible string "foo,bar" can be covered by multiple drivers sharing a
regmap, or by a single driver doing all the job without a regmap, but
these are implementation details which shouldn't reflect on the
devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
---
Notes:
v15: New patch
drivers/mfd/syscon.c | 46 +++++++++++++++++++++++++-------------
include/linux/mfd/syscon.h | 6 +++++
2 files changed, 36 insertions(+), 16 deletions(-)
diff --git a/drivers/mfd/syscon.c b/drivers/mfd/syscon.c
index b65e585fc8c6..660723276481 100644
--- a/drivers/mfd/syscon.c
+++ b/drivers/mfd/syscon.c
@@ -40,7 +40,7 @@ static const struct regmap_config syscon_regmap_config = {
.reg_stride = 4,
};
-static struct syscon *of_syscon_register(struct device_node *np)
+static struct syscon *of_syscon_register(struct device_node *np, bool check_clk)
{
struct clk *clk;
struct syscon *syscon;
@@ -51,9 +51,6 @@ static struct syscon *of_syscon_register(struct device_node *np)
struct regmap_config syscon_config = syscon_regmap_config;
struct resource res;
- if (!of_device_is_compatible(np, "syscon"))
- return ERR_PTR(-EINVAL);
-
syscon = kzalloc(sizeof(*syscon), GFP_KERNEL);
if (!syscon)
return ERR_PTR(-ENOMEM);
@@ -117,16 +114,18 @@ static struct syscon *of_syscon_register(struct device_node *np)
goto err_regmap;
}
- clk = of_clk_get(np, 0);
- if (IS_ERR(clk)) {
- ret = PTR_ERR(clk);
- /* clock is optional */
- if (ret != -ENOENT)
- goto err_clk;
- } else {
- ret = regmap_mmio_attach_clk(regmap, clk);
- if (ret)
- goto err_attach;
+ if (check_clk) {
+ clk = of_clk_get(np, 0);
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
+ /* clock is optional */
+ if (ret != -ENOENT)
+ goto err_clk;
+ } else {
+ ret = regmap_mmio_attach_clk(regmap, clk);
+ if (ret)
+ goto err_attach;
+ }
}
syscon->regmap = regmap;
@@ -150,7 +149,8 @@ static struct syscon *of_syscon_register(struct device_node *np)
return ERR_PTR(ret);
}
-struct regmap *syscon_node_to_regmap(struct device_node *np)
+static struct regmap *device_node_get_regmap(struct device_node *np,
+ bool check_clk)
{
struct syscon *entry, *syscon = NULL;
@@ -165,13 +165,27 @@ struct regmap *syscon_node_to_regmap(struct device_node *np)
spin_unlock(&syscon_list_slock);
if (!syscon)
- syscon = of_syscon_register(np);
+ syscon = of_syscon_register(np, check_clk);
if (IS_ERR(syscon))
return ERR_CAST(syscon);
return syscon->regmap;
}
+
+struct regmap *device_node_to_regmap(struct device_node *np)
+{
+ return device_node_get_regmap(np, false);
+}
+EXPORT_SYMBOL_GPL(device_node_to_regmap);
+
+struct regmap *syscon_node_to_regmap(struct device_node *np)
+{
+ if (!of_device_is_compatible(np, "syscon"))
+ return ERR_PTR(-EINVAL);
+
+ return device_node_get_regmap(np, true);
+}
EXPORT_SYMBOL_GPL(syscon_node_to_regmap);
struct regmap *syscon_regmap_lookup_by_compatible(const char *s)
diff --git a/include/linux/mfd/syscon.h b/include/linux/mfd/syscon.h
index 8cfda0554381..112dc66262cc 100644
--- a/include/linux/mfd/syscon.h
+++ b/include/linux/mfd/syscon.h
@@ -17,12 +17,18 @@
struct device_node;
#ifdef CONFIG_MFD_SYSCON
+extern struct regmap *device_node_to_regmap(struct device_node *np);
extern struct regmap *syscon_node_to_regmap(struct device_node *np);
extern struct regmap *syscon_regmap_lookup_by_compatible(const char *s);
extern struct regmap *syscon_regmap_lookup_by_phandle(
struct device_node *np,
const char *property);
#else
+static inline struct regmap *device_node_to_regmap(struct device_node *np)
+{
+ return ERR_PTR(-ENOTSUPP);
+}
+
static inline struct regmap *syscon_node_to_regmap(struct device_node *np)
{
return ERR_PTR(-ENOTSUPP);
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 05/13] clk: ingenic: Add driver for the TCU clocks
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
Add driver to support the clocks provided by the Timer/Counter Unit
(TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v12: New patch
v13:
- Don't enable/disable the TCU clock on demand. Enable it in the probe
and call it a day.
- Register suspend callbacks to gate/ungate the TCU clock on
suspend/resume.
- Use pr_fmt and pr_crit instead of custom TCU_ERR() macro
- Remove useless dependency on COMMON_CLK in Kconfig
- Remove registration of clkdev
v14: Change %i to %d
v15:
- Use CLK_OF_DECLARE_DRIVER macro since we use "simple-mfd"
- Use device_node_to_regmap()
drivers/clk/ingenic/Kconfig | 10 +-
drivers/clk/ingenic/Makefile | 1 +
drivers/clk/ingenic/tcu.c | 474 +++++++++++++++++++++++++++++++++++
3 files changed, 484 insertions(+), 1 deletion(-)
create mode 100644 drivers/clk/ingenic/tcu.c
diff --git a/drivers/clk/ingenic/Kconfig b/drivers/clk/ingenic/Kconfig
index fe8db93cf21a..1cb489959a99 100644
--- a/drivers/clk/ingenic/Kconfig
+++ b/drivers/clk/ingenic/Kconfig
@@ -1,5 +1,5 @@
# SPDX-License-Identifier: GPL-2.0-only
-menu "Ingenic JZ47xx CGU drivers"
+menu "Ingenic SoCs drivers"
depends on MIPS
config INGENIC_CGU_COMMON
@@ -45,4 +45,12 @@ config INGENIC_CGU_JZ4780
If building for a JZ4780 SoC, you want to say Y here.
+config INGENIC_TCU_CLK
+ bool "Ingenic JZ47xx TCU clocks driver"
+ default MACH_INGENIC
+ select MFD_SYSCON
+ help
+ Support the clocks of the Timer/Counter Unit (TCU) of the Ingenic
+ JZ47xx SoCs.
+
endmenu
diff --git a/drivers/clk/ingenic/Makefile b/drivers/clk/ingenic/Makefile
index 250570a809d3..097220b05131 100644
--- a/drivers/clk/ingenic/Makefile
+++ b/drivers/clk/ingenic/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_INGENIC_CGU_JZ4740) += jz4740-cgu.o
obj-$(CONFIG_INGENIC_CGU_JZ4725B) += jz4725b-cgu.o
obj-$(CONFIG_INGENIC_CGU_JZ4770) += jz4770-cgu.o
obj-$(CONFIG_INGENIC_CGU_JZ4780) += jz4780-cgu.o
+obj-$(CONFIG_INGENIC_TCU_CLK) += tcu.o
diff --git a/drivers/clk/ingenic/tcu.c b/drivers/clk/ingenic/tcu.c
new file mode 100644
index 000000000000..a1a5f9cb439e
--- /dev/null
+++ b/drivers/clk/ingenic/tcu.c
@@ -0,0 +1,474 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ47xx SoCs TCU clocks driver
+ * Copyright (C) 2019 Paul Cercueil <paul@crapouillou.net>
+ */
+
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/clockchips.h>
+#include <linux/mfd/ingenic-tcu.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/syscore_ops.h>
+
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/* 8 channels max + watchdog + OST */
+#define TCU_CLK_COUNT 10
+
+#undef pr_fmt
+#define pr_fmt(fmt) "ingenic-tcu-clk: " fmt
+
+enum tcu_clk_parent {
+ TCU_PARENT_PCLK,
+ TCU_PARENT_RTC,
+ TCU_PARENT_EXT,
+};
+
+struct ingenic_soc_info {
+ unsigned int num_channels;
+ bool has_ost;
+ bool has_tcu_clk;
+};
+
+struct ingenic_tcu_clk_info {
+ struct clk_init_data init_data;
+ u8 gate_bit;
+ u8 tcsr_reg;
+};
+
+struct ingenic_tcu_clk {
+ struct clk_hw hw;
+ unsigned int idx;
+ struct ingenic_tcu *tcu;
+ const struct ingenic_tcu_clk_info *info;
+};
+
+struct ingenic_tcu {
+ const struct ingenic_soc_info *soc_info;
+ struct regmap *map;
+ struct clk *clk;
+
+ struct clk_hw_onecell_data *clocks;
+};
+
+static struct ingenic_tcu *ingenic_tcu;
+
+static inline struct ingenic_tcu_clk *to_tcu_clk(struct clk_hw *hw)
+{
+ return container_of(hw, struct ingenic_tcu_clk, hw);
+}
+
+static int ingenic_tcu_enable(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ struct ingenic_tcu *tcu = tcu_clk->tcu;
+
+ regmap_write(tcu->map, TCU_REG_TSCR, BIT(info->gate_bit));
+
+ return 0;
+}
+
+static void ingenic_tcu_disable(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ struct ingenic_tcu *tcu = tcu_clk->tcu;
+
+ regmap_write(tcu->map, TCU_REG_TSSR, BIT(info->gate_bit));
+}
+
+static int ingenic_tcu_is_enabled(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ unsigned int value;
+
+ regmap_read(tcu_clk->tcu->map, TCU_REG_TSR, &value);
+
+ return !(value & BIT(info->gate_bit));
+}
+
+static bool ingenic_tcu_enable_regs(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ struct ingenic_tcu *tcu = tcu_clk->tcu;
+ bool enabled = false;
+
+ /*
+ * If the SoC has no global TCU clock, we must ungate the channel's
+ * clock to be able to access its registers.
+ * If we have a TCU clock, it will be enabled automatically as it has
+ * been attached to the regmap.
+ */
+ if (!tcu->clk) {
+ enabled = !!ingenic_tcu_is_enabled(hw);
+ regmap_write(tcu->map, TCU_REG_TSCR, BIT(info->gate_bit));
+ }
+
+ return enabled;
+}
+
+static void ingenic_tcu_disable_regs(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ struct ingenic_tcu *tcu = tcu_clk->tcu;
+
+ if (!tcu->clk)
+ regmap_write(tcu->map, TCU_REG_TSSR, BIT(info->gate_bit));
+}
+
+static u8 ingenic_tcu_get_parent(struct clk_hw *hw)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ unsigned int val = 0;
+ int ret;
+
+ ret = regmap_read(tcu_clk->tcu->map, info->tcsr_reg, &val);
+ WARN_ONCE(ret < 0, "Unable to read TCSR %d", tcu_clk->idx);
+
+ return ffs(val & TCU_TCSR_PARENT_CLOCK_MASK) - 1;
+}
+
+static int ingenic_tcu_set_parent(struct clk_hw *hw, u8 idx)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ bool was_enabled;
+ int ret;
+
+ was_enabled = ingenic_tcu_enable_regs(hw);
+
+ ret = regmap_update_bits(tcu_clk->tcu->map, info->tcsr_reg,
+ TCU_TCSR_PARENT_CLOCK_MASK, BIT(idx));
+ WARN_ONCE(ret < 0, "Unable to update TCSR %d", tcu_clk->idx);
+
+ if (!was_enabled)
+ ingenic_tcu_disable_regs(hw);
+
+ return 0;
+}
+
+static unsigned long ingenic_tcu_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ unsigned int prescale;
+ int ret;
+
+ ret = regmap_read(tcu_clk->tcu->map, info->tcsr_reg, &prescale);
+ WARN_ONCE(ret < 0, "Unable to read TCSR %d", tcu_clk->idx);
+
+ prescale = (prescale & TCU_TCSR_PRESCALE_MASK) >> TCU_TCSR_PRESCALE_LSB;
+
+ return parent_rate >> (prescale * 2);
+}
+
+static u8 ingenic_tcu_get_prescale(unsigned long rate, unsigned long req_rate)
+{
+ u8 prescale;
+
+ for (prescale = 0; prescale < 5; prescale++)
+ if ((rate >> (prescale * 2)) <= req_rate)
+ return prescale;
+
+ return 5; /* /1024 divider */
+}
+
+static long ingenic_tcu_round_rate(struct clk_hw *hw, unsigned long req_rate,
+ unsigned long *parent_rate)
+{
+ unsigned long rate = *parent_rate;
+ u8 prescale;
+
+ if (req_rate > rate)
+ return -EINVAL;
+
+ prescale = ingenic_tcu_get_prescale(rate, req_rate);
+
+ return rate >> (prescale * 2);
+}
+
+static int ingenic_tcu_set_rate(struct clk_hw *hw, unsigned long req_rate,
+ unsigned long parent_rate)
+{
+ struct ingenic_tcu_clk *tcu_clk = to_tcu_clk(hw);
+ const struct ingenic_tcu_clk_info *info = tcu_clk->info;
+ u8 prescale = ingenic_tcu_get_prescale(parent_rate, req_rate);
+ bool was_enabled;
+ int ret;
+
+ was_enabled = ingenic_tcu_enable_regs(hw);
+
+ ret = regmap_update_bits(tcu_clk->tcu->map, info->tcsr_reg,
+ TCU_TCSR_PRESCALE_MASK,
+ prescale << TCU_TCSR_PRESCALE_LSB);
+ WARN_ONCE(ret < 0, "Unable to update TCSR %d", tcu_clk->idx);
+
+ if (!was_enabled)
+ ingenic_tcu_disable_regs(hw);
+
+ return 0;
+}
+
+static const struct clk_ops ingenic_tcu_clk_ops = {
+ .get_parent = ingenic_tcu_get_parent,
+ .set_parent = ingenic_tcu_set_parent,
+
+ .recalc_rate = ingenic_tcu_recalc_rate,
+ .round_rate = ingenic_tcu_round_rate,
+ .set_rate = ingenic_tcu_set_rate,
+
+ .enable = ingenic_tcu_enable,
+ .disable = ingenic_tcu_disable,
+ .is_enabled = ingenic_tcu_is_enabled,
+};
+
+static const char * const ingenic_tcu_timer_parents[] = {
+ [TCU_PARENT_PCLK] = "pclk",
+ [TCU_PARENT_RTC] = "rtc",
+ [TCU_PARENT_EXT] = "ext",
+};
+
+#define DEF_TIMER(_name, _gate_bit, _tcsr) \
+ { \
+ .init_data = { \
+ .name = _name, \
+ .parent_names = ingenic_tcu_timer_parents, \
+ .num_parents = ARRAY_SIZE(ingenic_tcu_timer_parents),\
+ .ops = &ingenic_tcu_clk_ops, \
+ .flags = CLK_SET_RATE_UNGATE, \
+ }, \
+ .gate_bit = _gate_bit, \
+ .tcsr_reg = _tcsr, \
+ }
+static const struct ingenic_tcu_clk_info ingenic_tcu_clk_info[] = {
+ [TCU_CLK_TIMER0] = DEF_TIMER("timer0", 0, TCU_REG_TCSRc(0)),
+ [TCU_CLK_TIMER1] = DEF_TIMER("timer1", 1, TCU_REG_TCSRc(1)),
+ [TCU_CLK_TIMER2] = DEF_TIMER("timer2", 2, TCU_REG_TCSRc(2)),
+ [TCU_CLK_TIMER3] = DEF_TIMER("timer3", 3, TCU_REG_TCSRc(3)),
+ [TCU_CLK_TIMER4] = DEF_TIMER("timer4", 4, TCU_REG_TCSRc(4)),
+ [TCU_CLK_TIMER5] = DEF_TIMER("timer5", 5, TCU_REG_TCSRc(5)),
+ [TCU_CLK_TIMER6] = DEF_TIMER("timer6", 6, TCU_REG_TCSRc(6)),
+ [TCU_CLK_TIMER7] = DEF_TIMER("timer7", 7, TCU_REG_TCSRc(7)),
+};
+
+static const struct ingenic_tcu_clk_info ingenic_tcu_watchdog_clk_info =
+ DEF_TIMER("wdt", 16, TCU_REG_WDT_TCSR);
+static const struct ingenic_tcu_clk_info ingenic_tcu_ost_clk_info =
+ DEF_TIMER("ost", 15, TCU_REG_OST_TCSR);
+#undef DEF_TIMER
+
+static int __init ingenic_tcu_register_clock(struct ingenic_tcu *tcu,
+ unsigned int idx, enum tcu_clk_parent parent,
+ const struct ingenic_tcu_clk_info *info,
+ struct clk_hw_onecell_data *clocks)
+{
+ struct ingenic_tcu_clk *tcu_clk;
+ int err;
+
+ tcu_clk = kzalloc(sizeof(*tcu_clk), GFP_KERNEL);
+ if (!tcu_clk)
+ return -ENOMEM;
+
+ tcu_clk->hw.init = &info->init_data;
+ tcu_clk->idx = idx;
+ tcu_clk->info = info;
+ tcu_clk->tcu = tcu;
+
+ /* Reset channel and clock divider, set default parent */
+ ingenic_tcu_enable_regs(&tcu_clk->hw);
+ regmap_update_bits(tcu->map, info->tcsr_reg, 0xffff, BIT(parent));
+ ingenic_tcu_disable_regs(&tcu_clk->hw);
+
+ err = clk_hw_register(NULL, &tcu_clk->hw);
+ if (err) {
+ kfree(tcu_clk);
+ return err;
+ }
+
+ clocks->hws[idx] = &tcu_clk->hw;
+
+ return 0;
+}
+
+static const struct ingenic_soc_info jz4740_soc_info = {
+ .num_channels = 8,
+ .has_ost = false,
+ .has_tcu_clk = true,
+};
+
+static const struct ingenic_soc_info jz4725b_soc_info = {
+ .num_channels = 6,
+ .has_ost = true,
+ .has_tcu_clk = true,
+};
+
+static const struct ingenic_soc_info jz4770_soc_info = {
+ .num_channels = 8,
+ .has_ost = true,
+ .has_tcu_clk = false,
+};
+
+static const struct of_device_id ingenic_tcu_of_match[] __initconst = {
+ { .compatible = "ingenic,jz4740-tcu", .data = &jz4740_soc_info, },
+ { .compatible = "ingenic,jz4725b-tcu", .data = &jz4725b_soc_info, },
+ { .compatible = "ingenic,jz4770-tcu", .data = &jz4770_soc_info, },
+ { /* sentinel */ }
+};
+
+static int __init ingenic_tcu_probe(struct device_node *np)
+{
+ const struct of_device_id *id = of_match_node(ingenic_tcu_of_match, np);
+ struct ingenic_tcu *tcu;
+ struct regmap *map;
+ unsigned int i;
+ int ret;
+
+ map = device_node_to_regmap(np);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ tcu = kzalloc(sizeof(*tcu), GFP_KERNEL);
+ if (!tcu)
+ return -ENOMEM;
+
+ tcu->map = map;
+ tcu->soc_info = id->data;
+
+ if (tcu->soc_info->has_tcu_clk) {
+ tcu->clk = of_clk_get_by_name(np, "tcu");
+ if (IS_ERR(tcu->clk)) {
+ ret = PTR_ERR(tcu->clk);
+ pr_crit("Cannot get TCU clock\n");
+ goto err_free_tcu;
+ }
+
+ ret = clk_prepare_enable(tcu->clk);
+ if (ret) {
+ pr_crit("Unable to enable TCU clock\n");
+ goto err_put_clk;
+ }
+ }
+
+ tcu->clocks = kzalloc(sizeof(*tcu->clocks) +
+ sizeof(*tcu->clocks->hws) * TCU_CLK_COUNT,
+ GFP_KERNEL);
+ if (!tcu->clocks) {
+ ret = -ENOMEM;
+ goto err_clk_disable;
+ }
+
+ tcu->clocks->num = TCU_CLK_COUNT;
+
+ for (i = 0; i < tcu->soc_info->num_channels; i++) {
+ ret = ingenic_tcu_register_clock(tcu, i, TCU_PARENT_EXT,
+ &ingenic_tcu_clk_info[i],
+ tcu->clocks);
+ if (ret) {
+ pr_crit("cannot register clock %d\n", i);
+ goto err_unregister_timer_clocks;
+ }
+ }
+
+ /*
+ * We set EXT as the default parent clock for all the TCU clocks
+ * except for the watchdog one, where we set the RTC clock as the
+ * parent. Since the EXT and PCLK are much faster than the RTC clock,
+ * the watchdog would kick after a maximum time of 5s, and we might
+ * want a slower kicking time.
+ */
+ ret = ingenic_tcu_register_clock(tcu, TCU_CLK_WDT, TCU_PARENT_RTC,
+ &ingenic_tcu_watchdog_clk_info,
+ tcu->clocks);
+ if (ret) {
+ pr_crit("cannot register watchdog clock\n");
+ goto err_unregister_timer_clocks;
+ }
+
+ if (tcu->soc_info->has_ost) {
+ ret = ingenic_tcu_register_clock(tcu, TCU_CLK_OST,
+ TCU_PARENT_EXT,
+ &ingenic_tcu_ost_clk_info,
+ tcu->clocks);
+ if (ret) {
+ pr_crit("cannot register ost clock\n");
+ goto err_unregister_watchdog_clock;
+ }
+ }
+
+ ret = of_clk_add_hw_provider(np, of_clk_hw_onecell_get, tcu->clocks);
+ if (ret) {
+ pr_crit("cannot add OF clock provider\n");
+ goto err_unregister_ost_clock;
+ }
+
+ ingenic_tcu = tcu;
+
+ return 0;
+
+err_unregister_ost_clock:
+ if (tcu->soc_info->has_ost)
+ clk_hw_unregister(tcu->clocks->hws[i + 1]);
+err_unregister_watchdog_clock:
+ clk_hw_unregister(tcu->clocks->hws[i]);
+err_unregister_timer_clocks:
+ for (i = 0; i < tcu->clocks->num; i++)
+ if (tcu->clocks->hws[i])
+ clk_hw_unregister(tcu->clocks->hws[i]);
+ kfree(tcu->clocks);
+err_clk_disable:
+ if (tcu->soc_info->has_tcu_clk)
+ clk_disable_unprepare(tcu->clk);
+err_put_clk:
+ if (tcu->soc_info->has_tcu_clk)
+ clk_put(tcu->clk);
+err_free_tcu:
+ kfree(tcu);
+ return ret;
+}
+
+static int __maybe_unused tcu_pm_suspend(void)
+{
+ struct ingenic_tcu *tcu = ingenic_tcu;
+
+ if (tcu->clk)
+ clk_disable(tcu->clk);
+
+ return 0;
+}
+
+static void __maybe_unused tcu_pm_resume(void)
+{
+ struct ingenic_tcu *tcu = ingenic_tcu;
+
+ if (tcu->clk)
+ clk_enable(tcu->clk);
+}
+
+static struct syscore_ops __maybe_unused tcu_pm_ops = {
+ .suspend = tcu_pm_suspend,
+ .resume = tcu_pm_resume,
+};
+
+static void __init ingenic_tcu_init(struct device_node *np)
+{
+ int ret = ingenic_tcu_probe(np);
+
+ if (ret)
+ pr_crit("Failed to initialize TCU clocks: %d\n", ret);
+
+ if (IS_ENABLED(CONFIG_PM_SLEEP))
+ register_syscore_ops(&tcu_pm_ops);
+}
+
+CLK_OF_DECLARE_DRIVER(jz4740_cgu, "ingenic,jz4740-tcu", ingenic_tcu_init);
+CLK_OF_DECLARE_DRIVER(jz4725b_cgu, "ingenic,jz4725b-tcu", ingenic_tcu_init);
+CLK_OF_DECLARE_DRIVER(jz4770_cgu, "ingenic,jz4770-tcu", ingenic_tcu_init);
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 06/13] irqchip: Add irq-ingenic-tcu driver
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
This driver handles the interrupt controller built in the Timer/Counter
Unit (TCU) of the JZ47xx SoCs from Ingenic.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
---
Notes:
v12: New patch
v13: No change
v14: Remove empty lines in structure definitions
v15: Use device_node_to_regmap()
drivers/irqchip/Kconfig | 11 ++
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-ingenic-tcu.c | 182 ++++++++++++++++++++++++++++++
3 files changed, 194 insertions(+)
create mode 100644 drivers/irqchip/irq-ingenic-tcu.c
diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
index 80e10f4e213a..3c8308e6b3a7 100644
--- a/drivers/irqchip/Kconfig
+++ b/drivers/irqchip/Kconfig
@@ -315,6 +315,17 @@ config INGENIC_IRQ
depends on MACH_INGENIC
default y
+config INGENIC_TCU_IRQ
+ bool "Ingenic JZ47xx TCU interrupt controller"
+ default MACH_INGENIC
+ depends on MIPS || COMPILE_TEST
+ select MFD_SYSCON
+ help
+ Support for interrupts in the Timer/Counter Unit (TCU) of the Ingenic
+ JZ47xx SoCs.
+
+ If unsure, say N.
+
config RENESAS_H8300H_INTC
bool
select IRQ_DOMAIN
diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
index 8d0fcec6ab23..cc7c43932f16 100644
--- a/drivers/irqchip/Makefile
+++ b/drivers/irqchip/Makefile
@@ -75,6 +75,7 @@ obj-$(CONFIG_RENESAS_H8300H_INTC) += irq-renesas-h8300h.o
obj-$(CONFIG_RENESAS_H8S_INTC) += irq-renesas-h8s.o
obj-$(CONFIG_ARCH_SA1100) += irq-sa11x0.o
obj-$(CONFIG_INGENIC_IRQ) += irq-ingenic.o
+obj-$(CONFIG_INGENIC_TCU_IRQ) += irq-ingenic-tcu.o
obj-$(CONFIG_IMX_GPCV2) += irq-imx-gpcv2.o
obj-$(CONFIG_PIC32_EVIC) += irq-pic32-evic.o
obj-$(CONFIG_MSCC_OCELOT_IRQ) += irq-mscc-ocelot.o
diff --git a/drivers/irqchip/irq-ingenic-tcu.c b/drivers/irqchip/irq-ingenic-tcu.c
new file mode 100644
index 000000000000..6d05cefe9d79
--- /dev/null
+++ b/drivers/irqchip/irq-ingenic-tcu.c
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ47xx SoCs TCU IRQ driver
+ * Copyright (C) 2019 Paul Cercueil <paul@crapouillou.net>
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/mfd/ingenic-tcu.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of_irq.h>
+#include <linux/regmap.h>
+
+struct ingenic_tcu {
+ struct regmap *map;
+ struct clk *clk;
+ struct irq_domain *domain;
+ unsigned int nb_parent_irqs;
+ u32 parent_irqs[3];
+};
+
+static void ingenic_tcu_intc_cascade(struct irq_desc *desc)
+{
+ struct irq_chip *irq_chip = irq_data_get_irq_chip(&desc->irq_data);
+ struct irq_domain *domain = irq_desc_get_handler_data(desc);
+ struct irq_chip_generic *gc = irq_get_domain_generic_chip(domain, 0);
+ struct regmap *map = gc->private;
+ uint32_t irq_reg, irq_mask;
+ unsigned int i;
+
+ regmap_read(map, TCU_REG_TFR, &irq_reg);
+ regmap_read(map, TCU_REG_TMR, &irq_mask);
+
+ chained_irq_enter(irq_chip, desc);
+
+ irq_reg &= ~irq_mask;
+
+ for_each_set_bit(i, (unsigned long *)&irq_reg, 32)
+ generic_handle_irq(irq_linear_revmap(domain, i));
+
+ chained_irq_exit(irq_chip, desc);
+}
+
+static void ingenic_tcu_gc_unmask_enable_reg(struct irq_data *d)
+{
+ struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+ struct irq_chip_type *ct = irq_data_get_chip_type(d);
+ struct regmap *map = gc->private;
+ u32 mask = d->mask;
+
+ irq_gc_lock(gc);
+ regmap_write(map, ct->regs.ack, mask);
+ regmap_write(map, ct->regs.enable, mask);
+ *ct->mask_cache |= mask;
+ irq_gc_unlock(gc);
+}
+
+static void ingenic_tcu_gc_mask_disable_reg(struct irq_data *d)
+{
+ struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+ struct irq_chip_type *ct = irq_data_get_chip_type(d);
+ struct regmap *map = gc->private;
+ u32 mask = d->mask;
+
+ irq_gc_lock(gc);
+ regmap_write(map, ct->regs.disable, mask);
+ *ct->mask_cache &= ~mask;
+ irq_gc_unlock(gc);
+}
+
+static void ingenic_tcu_gc_mask_disable_reg_and_ack(struct irq_data *d)
+{
+ struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+ struct irq_chip_type *ct = irq_data_get_chip_type(d);
+ struct regmap *map = gc->private;
+ u32 mask = d->mask;
+
+ irq_gc_lock(gc);
+ regmap_write(map, ct->regs.ack, mask);
+ regmap_write(map, ct->regs.disable, mask);
+ irq_gc_unlock(gc);
+}
+
+static int __init ingenic_tcu_irq_init(struct device_node *np,
+ struct device_node *parent)
+{
+ struct irq_chip_generic *gc;
+ struct irq_chip_type *ct;
+ struct ingenic_tcu *tcu;
+ struct regmap *map;
+ unsigned int i;
+ int ret, irqs;
+
+ map = device_node_to_regmap(np);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ tcu = kzalloc(sizeof(*tcu), GFP_KERNEL);
+ if (!tcu)
+ return -ENOMEM;
+
+ tcu->map = map;
+
+ irqs = of_property_count_elems_of_size(np, "interrupts", sizeof(u32));
+ if (irqs < 0 || irqs > ARRAY_SIZE(tcu->parent_irqs)) {
+ pr_crit("%s: Invalid 'interrupts' property\n", __func__);
+ ret = -EINVAL;
+ goto err_free_tcu;
+ }
+
+ tcu->nb_parent_irqs = irqs;
+
+ tcu->domain = irq_domain_add_linear(np, 32, &irq_generic_chip_ops,
+ NULL);
+ if (!tcu->domain) {
+ ret = -ENOMEM;
+ goto err_free_tcu;
+ }
+
+ ret = irq_alloc_domain_generic_chips(tcu->domain, 32, 1, "TCU",
+ handle_level_irq, 0,
+ IRQ_NOPROBE | IRQ_LEVEL, 0);
+ if (ret) {
+ pr_crit("%s: Invalid 'interrupts' property\n", __func__);
+ goto out_domain_remove;
+ }
+
+ gc = irq_get_domain_generic_chip(tcu->domain, 0);
+ ct = gc->chip_types;
+
+ gc->wake_enabled = IRQ_MSK(32);
+ gc->private = tcu->map;
+
+ ct->regs.disable = TCU_REG_TMSR;
+ ct->regs.enable = TCU_REG_TMCR;
+ ct->regs.ack = TCU_REG_TFCR;
+ ct->chip.irq_unmask = ingenic_tcu_gc_unmask_enable_reg;
+ ct->chip.irq_mask = ingenic_tcu_gc_mask_disable_reg;
+ ct->chip.irq_mask_ack = ingenic_tcu_gc_mask_disable_reg_and_ack;
+ ct->chip.flags = IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE;
+
+ /* Mask all IRQs by default */
+ regmap_write(tcu->map, TCU_REG_TMSR, IRQ_MSK(32));
+
+ /*
+ * On JZ4740, timer 0 and timer 1 have their own interrupt line;
+ * timers 2-7 share one interrupt.
+ * On SoCs >= JZ4770, timer 5 has its own interrupt line;
+ * timers 0-4 and 6-7 share one single interrupt.
+ *
+ * To keep things simple, we just register the same handler to
+ * all parent interrupts. The handler will properly detect which
+ * channel fired the interrupt.
+ */
+ for (i = 0; i < irqs; i++) {
+ tcu->parent_irqs[i] = irq_of_parse_and_map(np, i);
+ if (!tcu->parent_irqs[i]) {
+ ret = -EINVAL;
+ goto out_unmap_irqs;
+ }
+
+ irq_set_chained_handler_and_data(tcu->parent_irqs[i],
+ ingenic_tcu_intc_cascade,
+ tcu->domain);
+ }
+
+ return 0;
+
+out_unmap_irqs:
+ for (; i > 0; i--)
+ irq_dispose_mapping(tcu->parent_irqs[i - 1]);
+out_domain_remove:
+ irq_domain_remove(tcu->domain);
+err_free_tcu:
+ kfree(tcu);
+ return ret;
+}
+IRQCHIP_DECLARE(jz4740_tcu_irq, "ingenic,jz4740-tcu", ingenic_tcu_irq_init);
+IRQCHIP_DECLARE(jz4725b_tcu_irq, "ingenic,jz4725b-tcu", ingenic_tcu_irq_init);
+IRQCHIP_DECLARE(jz4770_tcu_irq, "ingenic,jz4770-tcu", ingenic_tcu_irq_init);
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 07/13] clocksource: Add a new timer-ingenic driver
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
This driver handles the TCU (Timer Counter Unit) present on the Ingenic
JZ47xx SoCs, and provides the kernel with a system timer, a clocksource
and a sched_clock.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
---
Notes:
v2: Use SPDX identifier for the license
v3: - Move documentation to its own patch
- Search the devicetree for PWM clients, and use all the TCU
channels that won't be used for PWM
v4: - Add documentation about why we search for PWM clients
- Verify that the PWM clients are for the TCU PWM driver
v5: Major overhaul. Too many changes to list. Consider it's a new
patch.
v6: - Add two API functions ingenic_tcu_request_channel and
ingenic_tcu_release_channel. To be used by the PWM driver to
request the use of a TCU channel. The driver will now dynamically
move away the system timer or clocksource to a new TCU channel.
- The system timer now defaults to channel 0, the clocksource now
defaults to channel 1 and is no more optional. The
ingenic,timer-channel and ingenic,clocksource-channel devicetree
properties are now gone.
- Fix round_rate / set_rate not calculating the prescale divider
the same way. This caused problems when (parent_rate / div) would
give a non-integer result. The behaviour is correct now.
- The clocksource clock is turned off on suspend now.
v7: Fix section mismatch by using builtin_platform_driver_probe()
v8: - Removed ingenic_tcu_[request,release]_channel, and the mechanism
to dynamically change the TCU channel of the system timer or
the clocksource.
- The driver's devicetree node can now have two more children
nodes, that correspond to the system timer and clocksource.
For these two, the driver will use the TCU timer that
correspond to the memory resource supplied in their
respective node.
v9: - Removed support for clocksource / timer children devicetree
nodes. Now, we use a property "ingenic,pwm-channels-mask" to
know which PWM channels are reserved for PWM use and should
not be used as OS timers.
v10: - Use CLK_SET_RATE_UNGATE instead of CLK_SET_RATE_GATE + manually
un-gating the clock before changing rate. Same for re-parenting.
- Unconditionally create the clocksource and sched_clock even if
the SoC possesses a OS Timer. That gives the choice back to the
user which clocksource should be selected.
- Use subsys_initcall() instead of builtin_platform_driver_probe().
The OS Timer driver calls builtin_platform_driver_probe, which
requires the device to be created before that.
- Cosmetic cleanups
v11: - Change prototype of exported function
ingenic_tcu_pwm_can_use_chn(), use a struct device * as first
argument.
- Read clocksource using the regmap instead of bypassing it.
Bypassing the regmap makes sense only for the sched_clock where
the read operation must be as fast as possible.
- Fix incorrect format in pr_crit() macro
v12: - Clock handling and IRQ handling are gone, and are now handled
in their own driver.
- Obtain regmap from the ingenic-tcu MFD driver. As a result, we
cannot bypass the regmap anymore for the sched_clock.
v13: No change
v14: Remove empty lines in structure definitions
v15: Use device_node_to_regmap()
drivers/clocksource/Kconfig | 11 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/ingenic-timer.c | 356 ++++++++++++++++++++++++++++
3 files changed, 368 insertions(+)
create mode 100644 drivers/clocksource/ingenic-timer.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 5e9317dc3d39..a9cdc2c4f8bd 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -685,4 +685,15 @@ config MILBEAUT_TIMER
help
Enables the support for Milbeaut timer driver.
+config INGENIC_TIMER
+ bool "Clocksource/timer using the TCU in Ingenic JZ SoCs"
+ default MACH_INGENIC
+ depends on MIPS || COMPILE_TEST
+ depends on COMMON_CLK
+ select MFD_SYSCON
+ select TIMER_OF
+ select IRQ_DOMAIN
+ help
+ Support for the timer/counter unit of the Ingenic JZ SoCs.
+
endmenu
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 2e7936e7833f..4dfe4225ece7 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -80,6 +80,7 @@ obj-$(CONFIG_ASM9260_TIMER) += asm9260_timer.o
obj-$(CONFIG_H8300_TMR8) += h8300_timer8.o
obj-$(CONFIG_H8300_TMR16) += h8300_timer16.o
obj-$(CONFIG_H8300_TPU) += h8300_tpu.o
+obj-$(CONFIG_INGENIC_TIMER) += ingenic-timer.o
obj-$(CONFIG_CLKSRC_ST_LPC) += clksrc_st_lpc.o
obj-$(CONFIG_X86_NUMACHIP) += numachip.o
obj-$(CONFIG_ATCPIT100_TIMER) += timer-atcpit100.o
diff --git a/drivers/clocksource/ingenic-timer.c b/drivers/clocksource/ingenic-timer.c
new file mode 100644
index 000000000000..4bbdb3d3d0c6
--- /dev/null
+++ b/drivers/clocksource/ingenic-timer.c
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ47xx SoCs TCU IRQ driver
+ * Copyright (C) 2019 Paul Cercueil <paul@crapouillou.net>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/ingenic-tcu.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/sched_clock.h>
+
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+struct ingenic_soc_info {
+ unsigned int num_channels;
+};
+
+struct ingenic_tcu {
+ struct regmap *map;
+ struct clk *timer_clk, *cs_clk;
+ unsigned int timer_channel, cs_channel;
+ struct clock_event_device cevt;
+ struct clocksource cs;
+ char name[4];
+ unsigned long pwm_channels_mask;
+};
+
+static struct ingenic_tcu *ingenic_tcu;
+
+static u64 notrace ingenic_tcu_timer_read(void)
+{
+ struct ingenic_tcu *tcu = ingenic_tcu;
+ unsigned int count;
+
+ regmap_read(tcu->map, TCU_REG_TCNTc(tcu->cs_channel), &count);
+
+ return count;
+}
+
+static u64 notrace ingenic_tcu_timer_cs_read(struct clocksource *cs)
+{
+ return ingenic_tcu_timer_read();
+}
+
+static inline struct ingenic_tcu *to_ingenic_tcu(struct clock_event_device *evt)
+{
+ return container_of(evt, struct ingenic_tcu, cevt);
+}
+
+static int ingenic_tcu_cevt_set_state_shutdown(struct clock_event_device *evt)
+{
+ struct ingenic_tcu *tcu = to_ingenic_tcu(evt);
+
+ regmap_write(tcu->map, TCU_REG_TECR, BIT(tcu->timer_channel));
+
+ return 0;
+}
+
+static int ingenic_tcu_cevt_set_next(unsigned long next,
+ struct clock_event_device *evt)
+{
+ struct ingenic_tcu *tcu = to_ingenic_tcu(evt);
+
+ if (next > 0xffff)
+ return -EINVAL;
+
+ regmap_write(tcu->map, TCU_REG_TDFRc(tcu->timer_channel), next);
+ regmap_write(tcu->map, TCU_REG_TCNTc(tcu->timer_channel), 0);
+ regmap_write(tcu->map, TCU_REG_TESR, BIT(tcu->timer_channel));
+
+ return 0;
+}
+
+static irqreturn_t ingenic_tcu_cevt_cb(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = dev_id;
+ struct ingenic_tcu *tcu = to_ingenic_tcu(evt);
+
+ regmap_write(tcu->map, TCU_REG_TECR, BIT(tcu->timer_channel));
+
+ if (evt->event_handler)
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct clk * __init ingenic_tcu_get_clock(struct device_node *np, int id)
+{
+ struct of_phandle_args args;
+
+ args.np = np;
+ args.args_count = 1;
+ args.args[0] = id;
+
+ return of_clk_get_from_provider(&args);
+}
+
+static int __init ingenic_tcu_timer_init(struct device_node *np,
+ struct ingenic_tcu *tcu)
+{
+ unsigned int timer_virq, channel = tcu->timer_channel;
+ struct irq_domain *domain;
+ unsigned long rate;
+ int err;
+
+ tcu->timer_clk = ingenic_tcu_get_clock(np, channel);
+ if (IS_ERR(tcu->timer_clk))
+ return PTR_ERR(tcu->timer_clk);
+
+ err = clk_prepare_enable(tcu->timer_clk);
+ if (err)
+ goto err_clk_put;
+
+ rate = clk_get_rate(tcu->timer_clk);
+ if (!rate) {
+ err = -EINVAL;
+ goto err_clk_disable;
+ }
+
+ domain = irq_find_host(np);
+ if (!domain) {
+ err = -ENODEV;
+ goto err_clk_disable;
+ }
+
+ timer_virq = irq_create_mapping(domain, channel);
+ if (!timer_virq) {
+ err = -EINVAL;
+ goto err_clk_disable;
+ }
+
+ snprintf(tcu->name, sizeof(tcu->name), "TCU");
+
+ err = request_irq(timer_virq, ingenic_tcu_cevt_cb, IRQF_TIMER,
+ tcu->name, &tcu->cevt);
+ if (err)
+ goto err_irq_dispose_mapping;
+
+ tcu->cevt.cpumask = cpumask_of(smp_processor_id());
+ tcu->cevt.features = CLOCK_EVT_FEAT_ONESHOT;
+ tcu->cevt.name = tcu->name;
+ tcu->cevt.rating = 200;
+ tcu->cevt.set_state_shutdown = ingenic_tcu_cevt_set_state_shutdown;
+ tcu->cevt.set_next_event = ingenic_tcu_cevt_set_next;
+
+ clockevents_config_and_register(&tcu->cevt, rate, 10, 0xffff);
+
+ return 0;
+
+err_irq_dispose_mapping:
+ irq_dispose_mapping(timer_virq);
+err_clk_disable:
+ clk_disable_unprepare(tcu->timer_clk);
+err_clk_put:
+ clk_put(tcu->timer_clk);
+ return err;
+}
+
+static int __init ingenic_tcu_clocksource_init(struct device_node *np,
+ struct ingenic_tcu *tcu)
+{
+ unsigned int channel = tcu->cs_channel;
+ struct clocksource *cs = &tcu->cs;
+ unsigned long rate;
+ int err;
+
+ tcu->cs_clk = ingenic_tcu_get_clock(np, channel);
+ if (IS_ERR(tcu->cs_clk))
+ return PTR_ERR(tcu->cs_clk);
+
+ err = clk_prepare_enable(tcu->cs_clk);
+ if (err)
+ goto err_clk_put;
+
+ rate = clk_get_rate(tcu->cs_clk);
+ if (!rate) {
+ err = -EINVAL;
+ goto err_clk_disable;
+ }
+
+ /* Reset channel */
+ regmap_update_bits(tcu->map, TCU_REG_TCSRc(channel),
+ 0xffff & ~TCU_TCSR_RESERVED_BITS, 0);
+
+ /* Reset counter */
+ regmap_write(tcu->map, TCU_REG_TDFRc(channel), 0xffff);
+ regmap_write(tcu->map, TCU_REG_TCNTc(channel), 0);
+
+ /* Enable channel */
+ regmap_write(tcu->map, TCU_REG_TESR, BIT(channel));
+
+ cs->name = "ingenic-timer";
+ cs->rating = 200;
+ cs->flags = CLOCK_SOURCE_IS_CONTINUOUS;
+ cs->mask = CLOCKSOURCE_MASK(16);
+ cs->read = ingenic_tcu_timer_cs_read;
+
+ err = clocksource_register_hz(cs, rate);
+ if (err)
+ goto err_clk_disable;
+
+ return 0;
+
+err_clk_disable:
+ clk_disable_unprepare(tcu->cs_clk);
+err_clk_put:
+ clk_put(tcu->cs_clk);
+ return err;
+}
+
+static const struct ingenic_soc_info jz4740_soc_info = {
+ .num_channels = 8,
+};
+
+static const struct ingenic_soc_info jz4725b_soc_info = {
+ .num_channels = 6,
+};
+
+static const struct of_device_id ingenic_tcu_of_match[] = {
+ { .compatible = "ingenic,jz4740-tcu", .data = &jz4740_soc_info, },
+ { .compatible = "ingenic,jz4725b-tcu", .data = &jz4725b_soc_info, },
+ { .compatible = "ingenic,jz4770-tcu", .data = &jz4740_soc_info, },
+ { /* sentinel */ }
+};
+
+static int __init ingenic_tcu_init(struct device_node *np)
+{
+ const struct of_device_id *id = of_match_node(ingenic_tcu_of_match, np);
+ const struct ingenic_soc_info *soc_info = id->data;
+ struct ingenic_tcu *tcu;
+ struct regmap *map;
+ long rate;
+ int ret;
+
+ of_node_clear_flag(np, OF_POPULATED);
+
+ map = device_node_to_regmap(np);
+ if (IS_ERR(map))
+ return PTR_ERR(map);
+
+ tcu = kzalloc(sizeof(*tcu), GFP_KERNEL);
+ if (!tcu)
+ return -ENOMEM;
+
+ /* Enable all TCU channels for PWM use by default except channels 0/1 */
+ tcu->pwm_channels_mask = GENMASK(soc_info->num_channels - 1, 2);
+ of_property_read_u32(np, "ingenic,pwm-channels-mask",
+ (u32 *)&tcu->pwm_channels_mask);
+
+ /* Verify that we have at least two free channels */
+ if (hweight8(tcu->pwm_channels_mask) > soc_info->num_channels - 2) {
+ pr_crit("%s: Invalid PWM channel mask: 0x%02lx\n", __func__,
+ tcu->pwm_channels_mask);
+ ret = -EINVAL;
+ goto err_free_ingenic_tcu;
+ }
+
+ tcu->map = map;
+ ingenic_tcu = tcu;
+
+ tcu->timer_channel = find_first_zero_bit(&tcu->pwm_channels_mask,
+ soc_info->num_channels);
+ tcu->cs_channel = find_next_zero_bit(&tcu->pwm_channels_mask,
+ soc_info->num_channels,
+ tcu->timer_channel + 1);
+
+ ret = ingenic_tcu_clocksource_init(np, tcu);
+ if (ret) {
+ pr_crit("%s: Unable to init clocksource: %d\n", __func__, ret);
+ goto err_free_ingenic_tcu;
+ }
+
+ ret = ingenic_tcu_timer_init(np, tcu);
+ if (ret)
+ goto err_tcu_clocksource_cleanup;
+
+ /* Register the sched_clock at the end as there's no way to undo it */
+ rate = clk_get_rate(tcu->cs_clk);
+ sched_clock_register(ingenic_tcu_timer_read, 16, rate);
+
+ return 0;
+
+err_tcu_clocksource_cleanup:
+ clocksource_unregister(&tcu->cs);
+ clk_disable_unprepare(tcu->cs_clk);
+ clk_put(tcu->cs_clk);
+err_free_ingenic_tcu:
+ kfree(tcu);
+ return ret;
+}
+
+TIMER_OF_DECLARE(jz4740_tcu_intc, "ingenic,jz4740-tcu", ingenic_tcu_init);
+TIMER_OF_DECLARE(jz4725b_tcu_intc, "ingenic,jz4725b-tcu", ingenic_tcu_init);
+TIMER_OF_DECLARE(jz4770_tcu_intc, "ingenic,jz4770-tcu", ingenic_tcu_init);
+
+
+static int __init ingenic_tcu_probe(struct platform_device *pdev)
+{
+ platform_set_drvdata(pdev, ingenic_tcu);
+
+ return 0;
+}
+
+static int __maybe_unused ingenic_tcu_suspend(struct device *dev)
+{
+ struct ingenic_tcu *tcu = dev_get_drvdata(dev);
+
+ clk_disable(tcu->cs_clk);
+ clk_disable(tcu->timer_clk);
+ return 0;
+}
+
+static int __maybe_unused ingenic_tcu_resume(struct device *dev)
+{
+ struct ingenic_tcu *tcu = dev_get_drvdata(dev);
+ int ret;
+
+ ret = clk_enable(tcu->timer_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_enable(tcu->cs_clk);
+ if (ret) {
+ clk_disable(tcu->timer_clk);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct dev_pm_ops __maybe_unused ingenic_tcu_pm_ops = {
+ /* _noirq: We want the TCU clocks to be gated last / ungated first */
+ .suspend_noirq = ingenic_tcu_suspend,
+ .resume_noirq = ingenic_tcu_resume,
+};
+
+static struct platform_driver ingenic_tcu_driver = {
+ .driver = {
+ .name = "ingenic-tcu-timer",
+#ifdef CONFIG_PM_SLEEP
+ .pm = &ingenic_tcu_pm_ops,
+#endif
+ .of_match_table = ingenic_tcu_of_match,
+ },
+};
+builtin_platform_driver_probe(ingenic_tcu_driver, ingenic_tcu_probe);
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 08/13] clk: jz4740: Add TCU clock
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek, Rob Herring
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
Add the missing TCU clock to the list of clocks supplied by the CGU for
the JZ4740 SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
---
Notes:
v5: New patch
v6-v15: No change
drivers/clk/ingenic/jz4740-cgu.c | 6 ++++++
include/dt-bindings/clock/jz4740-cgu.h | 1 +
2 files changed, 7 insertions(+)
diff --git a/drivers/clk/ingenic/jz4740-cgu.c b/drivers/clk/ingenic/jz4740-cgu.c
index 4c0a20949c2c..67f8a0e14284 100644
--- a/drivers/clk/ingenic/jz4740-cgu.c
+++ b/drivers/clk/ingenic/jz4740-cgu.c
@@ -222,6 +222,12 @@ static const struct ingenic_cgu_clk_info jz4740_cgu_clocks[] = {
.parents = { JZ4740_CLK_EXT, -1, -1, -1 },
.gate = { CGU_REG_CLKGR, 5 },
},
+
+ [JZ4740_CLK_TCU] = {
+ "tcu", CGU_CLK_GATE,
+ .parents = { JZ4740_CLK_EXT, -1, -1, -1 },
+ .gate = { CGU_REG_CLKGR, 1 },
+ },
};
static void __init jz4740_cgu_init(struct device_node *np)
diff --git a/include/dt-bindings/clock/jz4740-cgu.h b/include/dt-bindings/clock/jz4740-cgu.h
index 6ed83f926ae7..e82d77028581 100644
--- a/include/dt-bindings/clock/jz4740-cgu.h
+++ b/include/dt-bindings/clock/jz4740-cgu.h
@@ -34,5 +34,6 @@
#define JZ4740_CLK_ADC 19
#define JZ4740_CLK_I2C 20
#define JZ4740_CLK_AIC 21
+#define JZ4740_CLK_TCU 22
#endif /* __DT_BINDINGS_CLOCK_JZ4740_CGU_H__ */
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 09/13] MIPS: jz4740: Add DTS nodes for the TCU drivers
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
Add DTS nodes for the JZ4780, JZ4770 and JZ4740 devicetree files.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v5: New patch
v6: Fix register lengths in watchdog/pwm nodes
v7: No change
v8: - Fix wrong start address for PWM node
- Add system timer and clocksource sub-nodes
v9: Drop timer and clocksource sub-nodes
v10-v11: No change
v12: Drop PWM/watchdog/OST sub-nodes, for now.
v13-v14: No change
v15: Add "simple-mfd" compatible string
arch/mips/boot/dts/ingenic/jz4740.dtsi | 22 ++++++++++++++++++++++
arch/mips/boot/dts/ingenic/jz4770.dtsi | 21 +++++++++++++++++++++
arch/mips/boot/dts/ingenic/jz4780.dtsi | 23 +++++++++++++++++++++++
3 files changed, 66 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/jz4740.dtsi b/arch/mips/boot/dts/ingenic/jz4740.dtsi
index 3ffaf63f22dd..058800bfc875 100644
--- a/arch/mips/boot/dts/ingenic/jz4740.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4740.dtsi
@@ -53,6 +53,28 @@
clock-names = "rtc";
};
+ tcu: timer@10002000 {
+ compatible = "ingenic,jz4740-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu JZ4740_CLK_RTC
+ &cgu JZ4740_CLK_EXT
+ &cgu JZ4740_CLK_PCLK
+ &cgu JZ4740_CLK_TCU>;
+ clock-names = "rtc", "ext", "pclk", "tcu";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <23 22 21>;
+ };
+
rtc_dev: rtc@10003000 {
compatible = "ingenic,jz4740-rtc";
reg = <0x10003000 0x40>;
diff --git a/arch/mips/boot/dts/ingenic/jz4770.dtsi b/arch/mips/boot/dts/ingenic/jz4770.dtsi
index 49ede6c14ff3..0bfb9edff3d0 100644
--- a/arch/mips/boot/dts/ingenic/jz4770.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4770.dtsi
@@ -46,6 +46,27 @@
#clock-cells = <1>;
};
+ tcu: timer@10002000 {
+ compatible = "ingenic,jz4770-tcu", "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu JZ4770_CLK_RTC
+ &cgu JZ4770_CLK_EXT
+ &cgu JZ4770_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+ };
+
pinctrl: pin-controller@10010000 {
compatible = "ingenic,jz4770-pinctrl";
reg = <0x10010000 0x600>;
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index b03cdec56de9..c54bd7cfec55 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -46,6 +46,29 @@
#clock-cells = <1>;
};
+ tcu: timer@10002000 {
+ compatible = "ingenic,jz4780-tcu",
+ "ingenic,jz4770-tcu",
+ "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu JZ4780_CLK_RTCLK
+ &cgu JZ4780_CLK_EXCLK
+ &cgu JZ4780_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+ };
+
rtc_dev: rtc@10003000 {
compatible = "ingenic,jz4780-rtc";
reg = <0x10003000 0x4c>;
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 10/13] MIPS: qi_lb60: Reduce system timer and clocksource to 750 kHz
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
The default clock (12 MHz) is too fast for the system timer, which fails
to report time accurately.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v5: New patch
v6: Remove ingenic,clocksource-channel property
v7-v15: No change
arch/mips/boot/dts/ingenic/qi_lb60.dts | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/qi_lb60.dts b/arch/mips/boot/dts/ingenic/qi_lb60.dts
index cc26650562c2..933d98ca8d93 100644
--- a/arch/mips/boot/dts/ingenic/qi_lb60.dts
+++ b/arch/mips/boot/dts/ingenic/qi_lb60.dts
@@ -2,6 +2,7 @@
/dts-v1/;
#include "jz4740.dtsi"
+#include <dt-bindings/clock/ingenic,tcu.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -64,3 +65,9 @@
pinctrl-names = "default";
pinctrl-0 = <&pins_mmc>;
};
+
+&tcu {
+ /* 750 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>;
+ assigned-clock-rates = <750000>, <750000>;
+};
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 11/13] MIPS: CI20: Reduce system timer and clocksource to 3 MHz
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
The default clock (48 MHz) is too fast for the system timer.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v5: New patch
v6: Set also the rate for the clocksource channel's clock
v7: No change
v8: No change
v9: Don't configure clock timer1, as the OS Timer is used as
clocksource on this SoC
v10: Revert back to v8 bahaviour. Let the user choose what
clocksource should be used.
v11-v15: No change
arch/mips/boot/dts/ingenic/ci20.dts | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 4f7b1fa31cf5..2e9952311ecd 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -2,6 +2,7 @@
/dts-v1/;
#include "jz4780.dtsi"
+#include <dt-bindings/clock/ingenic,tcu.h>
#include <dt-bindings/gpio/gpio.h>
/ {
@@ -238,3 +239,9 @@
bias-disable;
};
};
+
+&tcu {
+ /* 3 MHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>;
+ assigned-clock-rates = <3000000>, <3000000>;
+};
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 12/13] MIPS: GCW0: Reduce system timer and clocksource to 750 kHz
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
The default clock (12 MHz) is too fast for the system timer.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v8: New patch
v9: Don't configure clock timer1, as the OS Timer is used as
clocksource on this SoC
v10: Revert back to v8 bahaviour. Let the user choose what
clocksource should be used.
v11: No change
v12: Move clocksource to channel 2, as channel 1 is used as PWM
for the backlight.
v13-v15: No change
arch/mips/boot/dts/ingenic/gcw0.dts | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/mips/boot/dts/ingenic/gcw0.dts b/arch/mips/boot/dts/ingenic/gcw0.dts
index 35f0291e8d38..f58d239c2058 100644
--- a/arch/mips/boot/dts/ingenic/gcw0.dts
+++ b/arch/mips/boot/dts/ingenic/gcw0.dts
@@ -2,6 +2,7 @@
/dts-v1/;
#include "jz4770.dtsi"
+#include <dt-bindings/clock/ingenic,tcu.h>
/ {
compatible = "gcw,zero", "ingenic,jz4770";
@@ -60,3 +61,12 @@
/* The WiFi module is connected to the UHC. */
status = "okay";
};
+
+&tcu {
+ /* 750 kHz for the system timer and clocksource */
+ assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER2>;
+ assigned-clock-rates = <750000>, <750000>;
+
+ /* PWM1 is in use, so reserve channel #2 for the clocksource */
+ ingenic,pwm-channels-mask = <0xfa>;
+};
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH v15 13/13] MIPS: jz4740: Drop obsolete code
From: Paul Cercueil @ 2019-07-24 17:16 UTC (permalink / raw)
To: Ralf Baechle, Paul Burton, James Hogan, Jonathan Corbet,
Lee Jones, Arnd Bergmann, Daniel Lezcano, Thomas Gleixner,
Michael Turquette, Stephen Boyd, Jason Cooper, Marc Zyngier,
Rob Herring, Mark Rutland
Cc: devicetree, linux-kernel, linux-doc, linux-mips, linux-clk, od,
Mathieu Malaterre, Paul Cercueil, Artur Rojek
In-Reply-To: <20190724171615.20774-1-paul@crapouillou.net>
The old clocksource/timer platform code is now obsoleted by the newly
introduced TCU drivers.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
---
Notes:
v5: New patch
v6-v11: No change
v12: Only remove clocksource code. The rest will eventually be
removed in a future patchset when the PWM/watchdog drivers
are updated.
v13-v15: No change
arch/mips/jz4740/time.c | 151 +---------------------------------------
1 file changed, 2 insertions(+), 149 deletions(-)
diff --git a/arch/mips/jz4740/time.c b/arch/mips/jz4740/time.c
index cb768e560d8b..5476899f0882 100644
--- a/arch/mips/jz4740/time.c
+++ b/arch/mips/jz4740/time.c
@@ -4,161 +4,14 @@
* JZ4740 platform time support
*/
-#include <linux/clk.h>
#include <linux/clk-provider.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <linux/time.h>
+#include <linux/clocksource.h>
-#include <linux/clockchips.h>
-#include <linux/sched_clock.h>
-
-#include <asm/mach-jz4740/irq.h>
#include <asm/mach-jz4740/timer.h>
-#include <asm/time.h>
-
-#define TIMER_CLOCKEVENT 0
-#define TIMER_CLOCKSOURCE 1
-
-static uint16_t jz4740_jiffies_per_tick;
-
-static u64 jz4740_clocksource_read(struct clocksource *cs)
-{
- return jz4740_timer_get_count(TIMER_CLOCKSOURCE);
-}
-
-static struct clocksource jz4740_clocksource = {
- .name = "jz4740-timer",
- .rating = 200,
- .read = jz4740_clocksource_read,
- .mask = CLOCKSOURCE_MASK(16),
- .flags = CLOCK_SOURCE_IS_CONTINUOUS,
-};
-
-static u64 notrace jz4740_read_sched_clock(void)
-{
- return jz4740_timer_get_count(TIMER_CLOCKSOURCE);
-}
-
-static irqreturn_t jz4740_clockevent_irq(int irq, void *devid)
-{
- struct clock_event_device *cd = devid;
-
- jz4740_timer_ack_full(TIMER_CLOCKEVENT);
-
- if (!clockevent_state_periodic(cd))
- jz4740_timer_disable(TIMER_CLOCKEVENT);
-
- cd->event_handler(cd);
-
- return IRQ_HANDLED;
-}
-
-static int jz4740_clockevent_set_periodic(struct clock_event_device *evt)
-{
- jz4740_timer_set_count(TIMER_CLOCKEVENT, 0);
- jz4740_timer_set_period(TIMER_CLOCKEVENT, jz4740_jiffies_per_tick);
- jz4740_timer_irq_full_enable(TIMER_CLOCKEVENT);
- jz4740_timer_enable(TIMER_CLOCKEVENT);
-
- return 0;
-}
-
-static int jz4740_clockevent_resume(struct clock_event_device *evt)
-{
- jz4740_timer_irq_full_enable(TIMER_CLOCKEVENT);
- jz4740_timer_enable(TIMER_CLOCKEVENT);
-
- return 0;
-}
-
-static int jz4740_clockevent_shutdown(struct clock_event_device *evt)
-{
- jz4740_timer_disable(TIMER_CLOCKEVENT);
-
- return 0;
-}
-
-static int jz4740_clockevent_set_next(unsigned long evt,
- struct clock_event_device *cd)
-{
- jz4740_timer_set_count(TIMER_CLOCKEVENT, 0);
- jz4740_timer_set_period(TIMER_CLOCKEVENT, evt);
- jz4740_timer_enable(TIMER_CLOCKEVENT);
-
- return 0;
-}
-
-static struct clock_event_device jz4740_clockevent = {
- .name = "jz4740-timer",
- .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
- .set_next_event = jz4740_clockevent_set_next,
- .set_state_shutdown = jz4740_clockevent_shutdown,
- .set_state_periodic = jz4740_clockevent_set_periodic,
- .set_state_oneshot = jz4740_clockevent_shutdown,
- .tick_resume = jz4740_clockevent_resume,
- .rating = 200,
-#ifdef CONFIG_MACH_JZ4740
- .irq = JZ4740_IRQ_TCU0,
-#endif
-#if defined(CONFIG_MACH_JZ4770) || defined(CONFIG_MACH_JZ4780)
- .irq = JZ4780_IRQ_TCU2,
-#endif
-};
-
-static struct irqaction timer_irqaction = {
- .handler = jz4740_clockevent_irq,
- .flags = IRQF_PERCPU | IRQF_TIMER,
- .name = "jz4740-timerirq",
- .dev_id = &jz4740_clockevent,
-};
void __init plat_time_init(void)
{
- int ret;
- uint32_t clk_rate;
- uint16_t ctrl;
- struct clk *ext_clk;
-
of_clk_init(NULL);
jz4740_timer_init();
-
- ext_clk = clk_get(NULL, "ext");
- if (IS_ERR(ext_clk))
- panic("unable to get ext clock");
- clk_rate = clk_get_rate(ext_clk) >> 4;
- clk_put(ext_clk);
-
- jz4740_jiffies_per_tick = DIV_ROUND_CLOSEST(clk_rate, HZ);
-
- clockevent_set_clock(&jz4740_clockevent, clk_rate);
- jz4740_clockevent.min_delta_ns = clockevent_delta2ns(100, &jz4740_clockevent);
- jz4740_clockevent.min_delta_ticks = 100;
- jz4740_clockevent.max_delta_ns = clockevent_delta2ns(0xffff, &jz4740_clockevent);
- jz4740_clockevent.max_delta_ticks = 0xffff;
- jz4740_clockevent.cpumask = cpumask_of(0);
-
- clockevents_register_device(&jz4740_clockevent);
-
- ret = clocksource_register_hz(&jz4740_clocksource, clk_rate);
-
- if (ret)
- printk(KERN_ERR "Failed to register clocksource: %d\n", ret);
-
- sched_clock_register(jz4740_read_sched_clock, 16, clk_rate);
-
- setup_irq(jz4740_clockevent.irq, &timer_irqaction);
-
- ctrl = JZ_TIMER_CTRL_PRESCALE_16 | JZ_TIMER_CTRL_SRC_EXT;
-
- jz4740_timer_set_ctrl(TIMER_CLOCKEVENT, ctrl);
- jz4740_timer_set_ctrl(TIMER_CLOCKSOURCE, ctrl);
-
- jz4740_timer_set_period(TIMER_CLOCKEVENT, jz4740_jiffies_per_tick);
- jz4740_timer_irq_full_enable(TIMER_CLOCKEVENT);
-
- jz4740_timer_set_period(TIMER_CLOCKSOURCE, 0xffff);
-
- jz4740_timer_enable(TIMER_CLOCKEVENT);
- jz4740_timer_enable(TIMER_CLOCKSOURCE);
+ timer_probe();
}
--
2.21.0.593.g511ec345e18
^ permalink raw reply related
* [PATCH 2/2] arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
From: Dafna Hirschfeld @ 2019-07-24 17:17 UTC (permalink / raw)
To: dafna.hirschfeld
Cc: mark.rutland, devicetree, ezequiel, s.hauer, linux-kernel,
Gary Bisson, robh+dt, kernel, kernel, shawnguo, linux-arm-kernel
From: dafna <dafna.hirschfeld@collabora.com>
Add basic dts support for i.MX8MQ NITROGEN8M.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../arm64/boot/dts/freescale/imx8mq-nitrogen8m.dts | 411 +++++++++++++++++++++
2 files changed, 412 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-nitrogen8m.dts
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..54a5c18c5c30 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -26,3 +26,4 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen8m.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen8m.dts
new file mode 100644
index 000000000000..cfd4915d2916
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen8m.dts
@@ -0,0 +1,411 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2018 Boundary Devices
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx8mq.dtsi"
+
+/ {
+ model = "Boundary Devices i.MX8MQ Nitrogen8M";
+ compatible = "boundary,imx8mq-nitrogen8m", "fsl,imx8mq";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000 0 0x80000000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ power {
+ label = "Power Button";
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ gpio-key,wakeup;
+ };
+ };
+
+ reg_vref_0v9: regulator-vref-0v9 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-0v9";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ };
+
+ reg_vref_1v8: regulator-vref-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_vref_2v5: regulator-vref-2v5 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-2v5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ reg_vref_3v3: regulator-vref-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_vref_5v: regulator-vref-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&a53_opp_table {
+ opp-1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1000000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <900000>;
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
+ MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x59
+ >;
+ };
+
+ pinctrl_gpio_keys: gpio-keysgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x19
+ >;
+ };
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ /* J17 connector, odd */
+ MX8MQ_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19 /* Pin 19 */
+ MX8MQ_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19 /* Pin 21 */
+ MX8MQ_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x19 /* Pin 23 */
+ MX8MQ_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x19 /* Pin 25 */
+ MX8MQ_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x19 /* Pin 27 */
+ MX8MQ_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x19 /* Pin 29 */
+ MX8MQ_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x19 /* Pin 31 */
+ MX8MQ_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x19 /* Pin 33 */
+ MX8MQ_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x19 /* Pin 35 */
+ MX8MQ_IOMUXC_SAI1_TXD1_GPIO4_IO13 0x19 /* Pin 39 */
+ MX8MQ_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x19 /* Pin 41 */
+ MX8MQ_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x19 /* Pin 43 */
+ MX8MQ_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x19 /* Pin 45 */
+ MX8MQ_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x19 /* Pin 47 */
+ MX8MQ_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x19 /* Pin 49 */
+ MX8MQ_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x19 /* Pin 51 */
+
+ /* J17 connector, even */
+ MX8MQ_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19 /* Pin 44 */
+ MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19 /* Pin 48 */
+ MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x19 /* Pin 50 */
+ MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x19 /* Pin 54 */
+ MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x19 /* Pin 56 */
+
+ /* J18 connector, odd */
+ MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* Pin 41 */
+ MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* Pin 43 */
+ MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* Pin 45 */
+ MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* Pin 47 */
+ MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* Pin 49 */
+ MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19 /* Pin 53 */
+
+ /* J18 connector, even */
+ MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 /* Pin 32 */
+ MX8MQ_IOMUXC_NAND_CE0_B_GPIO3_IO1 0x19 /* Pin 36 */
+ MX8MQ_IOMUXC_NAND_DATA00_GPIO3_IO6 0x19 /* Pin 38 */
+ MX8MQ_IOMUXC_NAND_DATA01_GPIO3_IO7 0x19 /* Pin 40 */
+ MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8 0x19 /* Pin 42 */
+ MX8MQ_IOMUXC_NAND_DATA03_GPIO3_IO9 0x19 /* Pin 44 */
+ MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* Pin 46 */
+
+ /* J13 Pin 2, WL_WAKE */
+ MX8MQ_IOMUXC_SAI5_RXD2_GPIO3_IO23 0xd6
+ /* J13 Pin 4, WL_IRQ, not needed for Silex */
+ MX8MQ_IOMUXC_SAI5_RXD0_GPIO3_IO21 0xd6
+ /* J13 pin 9, unused */
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x19
+ /* J13 Pin 41, BT_CLK_REQ */
+ MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0xd6
+ /* J13 Pin 42, BT_HOST_WAKE */
+ MX8MQ_IOMUXC_SAI5_MCLK_GPIO3_IO25 0xd6
+
+ /* Clock for both CSI1 and CSI2 */
+ MX8MQ_IOMUXC_GPIO1_IO15_CCMSRCGPCMIX_CLKO2 0x07
+ /* test points */
+ MX8MQ_IOMUXC_GPIO1_IO04_GPIO1_IO4 0xc1 /* TP87 */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c1_pca9546: i2c1-pca9546grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x49
+ >;
+ };
+
+ pinctrl_i2c1d_rv4162: i2c1d-rv4162grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x49
+ >;
+ };
+
+ pinctrl_reg_arm_dram: reg-arm-dram {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x16
+ >;
+ };
+
+ pinctrl_reg_dram_1p1v: reg-dram-1p1v {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_STROBE_GPIO2_IO11 0x16
+ >;
+ };
+
+ pinctrl_reg_soc_gpu_vpu: reg-soc-gpu-vpu {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x16
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x45
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x45
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x45
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x45
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <4>;
+ interrupts-extended = <&gpio1 11 IRQ_TYPE_LEVEL_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <400000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ i2cmux@70 {
+ compatible = "pca9546";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_pca9546>;
+ reg = <0x70>;
+ reset-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ i2c1a: i2c1@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg_arm_dram: fan53555@60 {
+ compatible = "fcs,fan53555";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_arm_dram>;
+ reg = <0x60>;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ vsel-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c1b: i2c1@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg_dram_1p1v: fan53555@60 {
+ compatible = "fcs,fan53555";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_dram_1p1v>;
+ reg = <0x60>;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ vsel-gpios = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c1c: i2c1@2 {
+ reg = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg_soc_gpu_vpu: fan53555@60 {
+ compatible = "fcs,fan53555";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_soc_gpu_vpu>;
+ reg = <0x60>;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ vsel-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ i2c1d: i2c1@3 {
+ reg = <3>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ rtc@68 {
+ compatible = "microcrystal,rv4162";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1d_rv4162>;
+ reg = <0x68>;
+ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_LOW>;
+ wakeup-source;
+ };
+ };
+ };
+};
+
+&uart1 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+ status = "okay";
+};
+
+&usdhc1 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ non-removable;
+ vqmmc-1-8-v;
+ vmmc-supply = <®_vref_1v8>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related
* [PATCH 1/2] dt-bindings: arm: imx: add imx8mq nitrogen support
From: Dafna Hirschfeld @ 2019-07-24 17:17 UTC (permalink / raw)
To: dafna.hirschfeld
Cc: mark.rutland, devicetree, ezequiel, s.hauer, linux-kernel,
Gary Bisson, robh+dt, kernel, kernel, shawnguo, linux-arm-kernel
In-Reply-To: <20190724171747.26076-1-dafna.hirschfeld@collabora.com>
i.MX 8Quad is a quad (4x) Cortex-A53 processor with powerful
graphic and multimedia features.
This patch adds Nitrogen8M board support.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 7294ac36f4c0..728c41ef83bb 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -227,6 +227,12 @@ properties:
- fsl,imx8qxp-mek # i.MX8QXP MEK Board
- const: fsl,imx8qxp
+ - description: i.MX8MQ based Boards
+ items:
+ - enum:
+ - boundary,imx8mq-nitrogen8m # i.MX8MQ NITROGEN Board
+ - const: fsl,imx8mq
+
- description:
Freescale Vybrid Platform Device Tree Bindings
--
2.11.0
^ permalink raw reply related
* Re: [PATCH 1/2] dt-bindings: interconnect: Update Qualcomm SDM845 DT bindings
From: David Dai @ 2019-07-24 17:22 UTC (permalink / raw)
To: Stephen Boyd, bjorn.andersson, georgi.djakov, robh+dt
Cc: evgreen, ilina, seansw, elder, linux-kernel, devicetree,
linux-arm-msm, linux-pm
In-Reply-To: <5d3868a9.1c69fb81.876aa.ac30@mx.google.com>
On 7/24/2019 7:18 AM, Stephen Boyd wrote:
> Quoting David Dai (2019-07-23 14:48:42)
>> On 7/23/2019 7:42 AM, Stephen Boyd wrote:
>>> Quoting David Dai (2019-07-19 13:32:23)
>>>> +- compatible : shall contain only one of the following:
>>>> + "qcom,sdm845-bcm-voter",
>>>> +
>>>> +Examples:
>>>> +
>>>> +apps_rsc: rsc@179c0000 {
>>> But there isn't a reg property.
>> I'll change this to the generic example with just apps_rsc: rsc {
>>>> + label = "apps_rsc";
>>> Is label required?
> Any answer?
Not required.
>>>> + compatible = "qcom,rpmh-rsc";
>>>> +
>>>> + apps_bcm_voter: bcm_voter {
>>>> + compatible = "qcom,sdm845-bcm-voter";
>>>> + };
>>>> +}
>>>> +
>>>> +disp_rsc: rsc@179d0000 {
>>>> + label = "disp_rsc";
>>>> + compatible = "qcom,rpmh-rsc";
>>>> +
>>>> + disp_bcm_voter: bcm_voter {
>>>> + compatible = "qcom,sdm845-bcm-voter";
>>>> + };
>>>> +}
>>>> diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt
>>>> index 5c4f1d9..27f9ed9 100644
>>>> --- a/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt
>>>> +++ b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt
> [...]
>>>> +
>>>> +mem_noc: interconnect@1380000 {
>>>> + compatible = "qcom,sdm845-mem_noc";
>>>> + reg = <0 0x1380000 0 0x27200>;
>>>> + #interconnect-cells = <1>;
>>>> + qcom,bcm-voter = <&apps_bcm_voter>, <&disp_bcm_voter>;
>>>> +};
>>> How does a consumer target a particular RSC? For example, how can
>>> display decide to use the disp_bcm_voter node from mem_noc here? Maybe
>>> you can add that consumer to the example?
>> I was thinking that the association between the bcm voters and the icc
>> nodes would be handled by the interconnect provider, and that there
>> would be a set of display specific icc nodes with their own unique IDs
>> that the consumers could reference. I will mention this as part of the
>> description and provide an example.
>>
>> Ex: interconnects = <&mmss_noc MASTER_MDP0_DISP &mem_noc SLAVE_EBI_DISP>;
>>
> It looks backwards to me. Don't the consumers want to consume a
> particular RSC, i.e. apps or display RSC, so they can choose where to
> put the bcm vote and then those RSCs want to find MMIO registers for
> mmss_noc or mem_noc that they have to write to tune something else like
> QoS? If the MMIO space is the provider then I'm lost how it can
> differentiate between the RSCs that may be targetting the particular
> NoC.
The way that I view this is that the consumers consume both bandwidth
and QoS from these physical NoC devices by getting some path between two
endpoints on these different NoCs and applying some constraints. The NoC
providers can accomplish that either by writing to MMIO spaces or by
talking to some remote processor/hardware to tune its clock speed. The
consumer doesn't interact with the RSCs directly, but can select a
different bcm voter based on the endpoints that are associated with a
particular bcm(apps or disp rsc). Each node(endpoints) will have its own
BCM designation and an unique bcm voter.
> Maybe I've just completely missed something and this is all decided
> already. If so, sorry, I'm just trying to understand.
No problem, this just means I need to do a better job of explaining.
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH V14 00/13] PCI: tegra: Add Tegra194 PCIe support
From: Vidya Sagar @ 2019-07-24 17:48 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
Tegra194 has six PCIe controllers based on Synopsys DesignWare core.
There are two Universal PHY (UPHY) blocks with each supporting 12(HSIO:
Hisg Speed IO) and 8(NVHS: NVIDIA High Speed) lanes respectively.
Controllers:0~4 use UPHY lanes from HSIO brick whereas Controller:5 uses
UPHY lanes from NVHS brick. Lane mapping in HSIO UPHY brick to each PCIe
controller (0~4) is controlled in XBAR module by BPMP-FW. Since PCIe
core has PIPE interface, a glue module called PIPE-to-UPHY (P2U) is used
to connect each UPHY lane (applicable to both HSIO and NVHS UPHY bricks)
to PCIe controller
This patch series
- Adds support for P2U PHY driver
- Adds support for PCIe host controller
- Adds device tree nodes each PCIe controllers
- Enables nodes applicable to p2972-0000 platform
- Adds helper APIs in Designware core driver to get capability regs offset
- Adds defines for new feature registers of PCIe spec revision 4
- Makes changes in DesignWare core driver to get Tegra194 PCIe working
Testing done on P2972-0000 platform
- Able to get PCIe link up with on-board Marvel eSATA controller
- Able to get PCIe link up with NVMe cards connected to M.2 Key-M slot
- Able to do data transfers with both SATA drives and NVMe cards
Note
- Enabling x8 slot on P2972-0000 platform requires pinmux driver for Tegra194.
It is being worked on currently and hence Controller:5 (i.e. x8 slot) is
disabled in this patch series. A future patch series would enable this.
- This series is based on top of the following series
Jisheng's patches to add support to .remove() in Designware sub-system
https://patchwork.kernel.org/project/linux-pci/list/?series=98559
(Update: Jisheng's patches are now accepted and applied for v5.2)
My patches made on top of Jisheng's patches to export various symbols
http://patchwork.ozlabs.org/project/linux-pci/list/?series=115671
(Update: My above patch series is accepted and applied for v5.3)
V14:
* Addressed Lorenzo's review comments in pcie-tegra194.c file (Patch 13/13)
* Added a new patch to export dw_pcie_wait_for_link() API
V13:
* Addressed Bjorn's review comments for adding Gen-4 specific defines to pci_regs.h header file
V12:
* Modified the commit message of patch-3 in this series to address review
comments from Lorenzo
V11:
* Removed device-tree patches from the series as they are applied to relevant
Tegra specific trees by Thierry Reding.
* Included older Tegra chips to extend quirk that disables MSI interrupt being
used for Tegra PCIe root ports.
* Addressed review comments in P2U driver file.
V10:
* Used _relaxed() versions of readl() & writel()
V9:
* Made the drivers dependent on ARCH_TEGRA_194_SOC directly
* Addressed review comments from Dmitry
V8:
* Changed P2U driver file name from pcie-p2u-tegra194.c to phy-tegra194-p2u.c
* Addressed review comments from Thierry and Rob
V7:
* Took care of review comments from Rob
* Added a quirk to disable MSI for root ports
* Removed using pcie_pme_disable_msi() API in host controller driver
V6:
* Removed patch that exports pcie_bus_config symbol
* Took care of review comments from Thierry and Rob
V5:
* Removed redundant APIs in pcie-designware-ep.c file after moving them
to pcie-designware.c file based on Bjorn's review comments
V4:
* Rebased on top of linux-next top of the tree
* Addressed Gustavo's comments and added his Ack for some of the changes.
V3:
* Addressed review comments from Thierry
V2:
* Addressed review comments from Bjorn, Thierry, Jonathan, Rob & Kishon
* Added more patches in v2 series
Vidya Sagar (13):
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: Disable MSI for Tegra root ports
PCI: dwc: Perform dbi regs write lock towards the end
PCI: dwc: Move config space capability search API
PCI: dwc: Add ext config space capability search API
PCI: dwc: Export dw_pcie_wait_for_link() API
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Add support to enable CDM register check
dt-bindings: Add PCIe supports-clkreq property
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: PHY: P2U: Add Tegra194 P2U block
phy: tegra: Add PCIe PIPE2UPHY support
PCI: tegra: Add Tegra194 PCIe support
.../bindings/pci/designware-pcie.txt | 5 +
.../bindings/pci/nvidia,tegra194-pcie.txt | 155 ++
Documentation/devicetree/bindings/pci/pci.txt | 5 +
.../bindings/phy/phy-tegra194-p2u.txt | 28 +
drivers/pci/controller/dwc/Kconfig | 10 +
drivers/pci/controller/dwc/Makefile | 1 +
.../pci/controller/dwc/pcie-designware-ep.c | 37 +-
.../pci/controller/dwc/pcie-designware-host.c | 14 +-
drivers/pci/controller/dwc/pcie-designware.c | 88 +
drivers/pci/controller/dwc/pcie-designware.h | 12 +
drivers/pci/controller/dwc/pcie-tegra194.c | 1630 +++++++++++++++++
drivers/pci/quirks.c | 53 +
drivers/phy/tegra/Kconfig | 7 +
drivers/phy/tegra/Makefile | 1 +
drivers/phy/tegra/phy-tegra194-p2u.c | 120 ++
include/uapi/linux/pci_regs.h | 14 +-
16 files changed, 2138 insertions(+), 42 deletions(-)
create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt
create mode 100644 drivers/pci/controller/dwc/pcie-tegra194.c
create mode 100644 drivers/phy/tegra/phy-tegra194-p2u.c
--
2.17.1
^ permalink raw reply
* [PATCH V14 01/13] PCI: Add #defines for some of PCIe spec r4.0 features
From: Vidya Sagar @ 2019-07-24 17:48 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190724174824.20933-1-vidyas@nvidia.com>
Add #defines only for the Data Link Feature and Physical Layer 16.0 GT/s
features as defined in PCIe spec r4.0, sec 7.7.4 for Data Link Feature and
sec 7.7.5 for Physical Layer 16.0 GT/s.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
---
V14:
* Added 'Acked-by: Bjorn Helgaas <bhelgaas@google.com>'
V13:
* Updated commit message to include references from spec
* Removed unused defines and moved some from pcie-tegra194.c file
* Addressed review comments from Bjorn
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* None
V5:
* None
V4:
* None
V3:
* Updated commit message and description to explicitly mention that defines are
added only for some of the features and not all.
V2:
* None
include/uapi/linux/pci_regs.h | 14 +++++++++++++-
1 file changed, 13 insertions(+), 1 deletion(-)
diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h
index f28e562d7ca8..d28d0319d932 100644
--- a/include/uapi/linux/pci_regs.h
+++ b/include/uapi/linux/pci_regs.h
@@ -713,7 +713,9 @@
#define PCI_EXT_CAP_ID_DPC 0x1D /* Downstream Port Containment */
#define PCI_EXT_CAP_ID_L1SS 0x1E /* L1 PM Substates */
#define PCI_EXT_CAP_ID_PTM 0x1F /* Precision Time Measurement */
-#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PTM
+#define PCI_EXT_CAP_ID_DLF 0x25 /* Data Link Feature */
+#define PCI_EXT_CAP_ID_PL_16GT 0x26 /* Physical Layer 16.0 GT/s */
+#define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_PL_16GT
#define PCI_EXT_CAP_DSN_SIZEOF 12
#define PCI_EXT_CAP_MCAST_ENDPOINT_SIZEOF 40
@@ -1053,4 +1055,14 @@
#define PCI_L1SS_CTL1_LTR_L12_TH_SCALE 0xe0000000 /* LTR_L1.2_THRESHOLD_Scale */
#define PCI_L1SS_CTL2 0x0c /* Control 2 Register */
+/* Data Link Feature */
+#define PCI_DLF_CAP 0x04 /* Capabilities Register */
+#define PCI_DLF_EXCHANGE_ENABLE 0x80000000 /* Data Link Feature Exchange Enable */
+
+/* Physical Layer 16.0 GT/s */
+#define PCI_PL_16GT_LE_CTRL 0x20 /* Lane Equalization Control Register */
+#define PCI_PL_16GT_LE_CTRL_DSP_TX_PRESET_MASK 0x0000000F
+#define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_MASK 0x000000F0
+#define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_SHIFT 4
+
#endif /* LINUX_PCI_REGS_H */
--
2.17.1
^ permalink raw reply related
* [PATCH V14 02/13] PCI: Disable MSI for Tegra root ports
From: Vidya Sagar @ 2019-07-24 17:48 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190724174824.20933-1-vidyas@nvidia.com>
Tegra PCIe rootports don't generate MSI interrupts for PME and AER events.
Since PCIe spec (Ref: r4.0 sec 7.7.1.2 and 7.7.2.2) doesn't support using
a mix of INTx and MSI/MSI-X, MSI needs to be disabled to avoid root ports
service drivers registering their respective ISRs with MSI interrupt and
to let only INTx be used for all events.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V14:
* None
V13:
* None
V12:
* None
V11:
* Included older Tegra chips to extend the quirk as this issue is present in
older Tegra chips as well.
V10:
* None
V9:
* None
V8:
* Changed quirk macro to consider class code as well to avoid this quirk
getting applied to Tegra194 when it is operating in endpoint mode. Also
quoted relevant sections from PCIe spec in comments.
V7:
* This is a new patch
drivers/pci/quirks.c | 53 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index c66c0ca446c4..1d3cac43ecbc 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -2592,6 +2592,59 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NVIDIA,
PCI_DEVICE_ID_NVIDIA_NVENET_15,
nvenet_msi_disable);
+/*
+ * PCIe spec r4.0 sec 7.7.1.2 and sec 7.7.2.2 say that if MSI/MSI-X is enabled,
+ * then the device can't use INTx interrupts. Tegra's PCIe root ports don't
+ * generate MSI interrupts for PME and AER events instead only INTx interrupts
+ * are generated. Though Tegra's PCIe root ports can generate MSI interrupts
+ * for other events, since PCIe specificiation doesn't support using a mix of
+ * INTx and MSI/MSI-X, it is required to disable MSI interrupts to avoid port
+ * service drivers registering their respective ISRs for MSIs.
+ */
+static void pci_quirk_nvidia_tegra_disable_rp_msi(struct pci_dev *dev)
+{
+ dev->no_msi = 1;
+}
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad0,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad1,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x1ad2,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf0,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0bf1,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1c,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e1d,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e12,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0e13,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0fae,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x0faf,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e5,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_NVIDIA, 0x10e6,
+ PCI_CLASS_BRIDGE_PCI, 8,
+ pci_quirk_nvidia_tegra_disable_rp_msi);
+
/*
* Some versions of the MCP55 bridge from Nvidia have a legacy IRQ routing
* config register. This register controls the routing of legacy
--
2.17.1
^ permalink raw reply related
* [PATCH V14 03/13] PCI: dwc: Perform dbi regs write lock towards the end
From: Vidya Sagar @ 2019-07-24 17:48 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190724174824.20933-1-vidyas@nvidia.com>
Some of DesignWare core's DBI registers (a.k.a configuration space
registers) are write-protected with a lock without enabling which they are
read-only by default. These write-protected registers are implementation
specific. Tegra194's BAR-0 register which is at offset 0x10 in the
configuration space is an example. Current implementation in
dw_pcie_setup_rc() API attempts to unlock those write-protected registers
whenever they are updated and lock them back again for writing. This patch
attempts to unlock all such write-protected registers for writing in the
beginning of the API once and lock them back again towards the end to avoid
bloating the API with multiple unlock/lock sequences for all those
write-protected registers.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
---
V14:
* None
V13:
* None
V12:
* Modified commit message to make it explicit that write-protected registers are
implementation specific.
V11:
* None
V10:
* None
V9:
* None
V8:
* None
V7:
* None
V6:
* Moved write enable to the beginning of the API and write disable to the end
V5:
* None
V4:
* None
V3:
* None
V2:
* None
drivers/pci/controller/dwc/pcie-designware-host.c | 14 ++++++++------
1 file changed, 8 insertions(+), 6 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
index f93252d0da5b..d3156446ff27 100644
--- a/drivers/pci/controller/dwc/pcie-designware-host.c
+++ b/drivers/pci/controller/dwc/pcie-designware-host.c
@@ -628,6 +628,12 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
u32 val, ctrl, num_ctrls;
struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+ /*
+ * Enable DBI read-only registers for writing/updating configuration.
+ * Write permission gets disabled towards the end of this function.
+ */
+ dw_pcie_dbi_ro_wr_en(pci);
+
dw_pcie_setup(pci);
if (!pp->ops->msi_host_init) {
@@ -650,12 +656,10 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_1, 0x00000000);
/* Setup interrupt pins */
- dw_pcie_dbi_ro_wr_en(pci);
val = dw_pcie_readl_dbi(pci, PCI_INTERRUPT_LINE);
val &= 0xffff00ff;
val |= 0x00000100;
dw_pcie_writel_dbi(pci, PCI_INTERRUPT_LINE, val);
- dw_pcie_dbi_ro_wr_dis(pci);
/* Setup bus numbers */
val = dw_pcie_readl_dbi(pci, PCI_PRIMARY_BUS);
@@ -687,15 +691,13 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
- /* Enable write permission for the DBI read-only register */
- dw_pcie_dbi_ro_wr_en(pci);
/* Program correct class for RC */
dw_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI);
- /* Better disable write permission right after the update */
- dw_pcie_dbi_ro_wr_dis(pci);
dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val);
val |= PORT_LOGIC_SPEED_CHANGE;
dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
+
+ dw_pcie_dbi_ro_wr_dis(pci);
}
EXPORT_SYMBOL_GPL(dw_pcie_setup_rc);
--
2.17.1
^ permalink raw reply related
* [PATCH V14 04/13] PCI: dwc: Move config space capability search API
From: Vidya Sagar @ 2019-07-24 17:48 UTC (permalink / raw)
To: lorenzo.pieralisi, bhelgaas, robh+dt, mark.rutland,
thierry.reding, jonathanh, kishon, catalin.marinas, will.deacon,
jingoohan1, gustavo.pimentel
Cc: digetx, mperttunen, linux-pci, devicetree, linux-tegra,
linux-kernel, linux-arm-kernel, kthota, mmaddireddy, vidyas,
sagar.tv
In-Reply-To: <20190724174824.20933-1-vidyas@nvidia.com>
Move PCIe config space capability search API to common DesignWare file
as this can be used by both host and ep mode codes.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
---
V14:
* None
V13:
* None
V12:
* None
V11:
* None
V10:
* None
V9:
* None
V8:
* Changed comment to explicitly state their mere resemblance to standard APIs
but not their operation and place of use.
V7:
* Exported dw_pcie_find_capability() API
V6:
* None
V5:
* Removed redundant APIs in pcie-designware-ep.c file after moving them
to pcie-designware.c file based on Bjorn's comments.
V4:
* Rebased to linux-next top of the tree
V3:
* None
V2:
* Removed dw_pcie_find_next_ext_capability() API from here and made a
separate patch for that
.../pci/controller/dwc/pcie-designware-ep.c | 37 +-----------------
drivers/pci/controller/dwc/pcie-designware.c | 39 +++++++++++++++++++
drivers/pci/controller/dwc/pcie-designware.h | 2 +
3 files changed, 43 insertions(+), 35 deletions(-)
diff --git a/drivers/pci/controller/dwc/pcie-designware-ep.c b/drivers/pci/controller/dwc/pcie-designware-ep.c
index 2bf5a35c0570..65f479250087 100644
--- a/drivers/pci/controller/dwc/pcie-designware-ep.c
+++ b/drivers/pci/controller/dwc/pcie-designware-ep.c
@@ -40,39 +40,6 @@ void dw_pcie_ep_reset_bar(struct dw_pcie *pci, enum pci_barno bar)
__dw_pcie_ep_reset_bar(pci, bar, 0);
}
-static u8 __dw_pcie_ep_find_next_cap(struct dw_pcie *pci, u8 cap_ptr,
- u8 cap)
-{
- u8 cap_id, next_cap_ptr;
- u16 reg;
-
- if (!cap_ptr)
- return 0;
-
- reg = dw_pcie_readw_dbi(pci, cap_ptr);
- cap_id = (reg & 0x00ff);
-
- if (cap_id > PCI_CAP_ID_MAX)
- return 0;
-
- if (cap_id == cap)
- return cap_ptr;
-
- next_cap_ptr = (reg & 0xff00) >> 8;
- return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
-}
-
-static u8 dw_pcie_ep_find_capability(struct dw_pcie *pci, u8 cap)
-{
- u8 next_cap_ptr;
- u16 reg;
-
- reg = dw_pcie_readw_dbi(pci, PCI_CAPABILITY_LIST);
- next_cap_ptr = (reg & 0x00ff);
-
- return __dw_pcie_ep_find_next_cap(pci, next_cap_ptr, cap);
-}
-
static int dw_pcie_ep_write_header(struct pci_epc *epc, u8 func_no,
struct pci_epf_header *hdr)
{
@@ -612,9 +579,9 @@ int dw_pcie_ep_init(struct dw_pcie_ep *ep)
dev_err(dev, "Failed to reserve memory for MSI/MSI-X\n");
return -ENOMEM;
}
- ep->msi_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSI);
+ ep->msi_cap = dw_pcie_find_capability(pci, PCI_CAP_ID_MSI);
- ep->msix_cap = dw_pcie_ep_find_capability(pci, PCI_CAP_ID_MSIX);
+ ep->msix_cap = dw_pcie_find_capability(pci, PCI_CAP_ID_MSIX);
offset = dw_pcie_ep_find_ext_capability(pci, PCI_EXT_CAP_ID_REBAR);
if (offset) {
diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index 7d25102c304c..7818b4febb08 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -14,6 +14,45 @@
#include "pcie-designware.h"
+/*
+ * These interfaces resemble the pci_find_*capability() interfaces, but these
+ * are for configuring host controllers, which are bridges *to* PCI devices but
+ * are not PCI devices themselves.
+ */
+static u8 __dw_pcie_find_next_cap(struct dw_pcie *pci, u8 cap_ptr,
+ u8 cap)
+{
+ u8 cap_id, next_cap_ptr;
+ u16 reg;
+
+ if (!cap_ptr)
+ return 0;
+
+ reg = dw_pcie_readw_dbi(pci, cap_ptr);
+ cap_id = (reg & 0x00ff);
+
+ if (cap_id > PCI_CAP_ID_MAX)
+ return 0;
+
+ if (cap_id == cap)
+ return cap_ptr;
+
+ next_cap_ptr = (reg & 0xff00) >> 8;
+ return __dw_pcie_find_next_cap(pci, next_cap_ptr, cap);
+}
+
+u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap)
+{
+ u8 next_cap_ptr;
+ u16 reg;
+
+ reg = dw_pcie_readw_dbi(pci, PCI_CAPABILITY_LIST);
+ next_cap_ptr = (reg & 0x00ff);
+
+ return __dw_pcie_find_next_cap(pci, next_cap_ptr, cap);
+}
+EXPORT_SYMBOL_GPL(dw_pcie_find_capability);
+
int dw_pcie_read(void __iomem *addr, int size, u32 *val)
{
if (!IS_ALIGNED((uintptr_t)addr, size)) {
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index ffed084a0b4f..d8c66a6827dc 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -251,6 +251,8 @@ struct dw_pcie {
#define to_dw_pcie_from_ep(endpoint) \
container_of((endpoint), struct dw_pcie, ep)
+u8 dw_pcie_find_capability(struct dw_pcie *pci, u8 cap);
+
int dw_pcie_read(void __iomem *addr, int size, u32 *val);
int dw_pcie_write(void __iomem *addr, int size, u32 val);
--
2.17.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox