Devicetree
 help / color / mirror / Atom feed
* [PATCH v4 0/2] gpio: Add Cortina Systems CS75xx GPIO driver
@ 2026-11-16  2:08 Fil Dunsky via B4 Relay
  2026-11-16  2:08 ` [PATCH v4 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
  2026-11-16  2:08 ` [PATCH v4 2/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
  0 siblings, 2 replies; 4+ messages in thread
From: Fil Dunsky via B4 Relay @ 2026-11-16  2:08 UTC (permalink / raw)
  To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
	Krzysztof Kozlowski, Conor Dooley
  Cc: linux-gpio, devicetree, linux-kernel, linux-arm-kernel,
	Fil Dunsky

The Cortina Systems CS75xx ("Goldengate G2") SoCs have five banks of 32
GPIO lines, each bank with its own interrupt. This series adds the
binding and a driver based on gpio-mmio; level and edge triggers are
supported, both edges are emulated by flipping the polarity.

Each pin is either a GPIO line or belongs to a peripheral (NAND,
Ethernet, UART, I2C, ...). That choice is made in the global control
block, which is not part of the GPIO controller: as discussed on v1 [1],
the driver does not touch the pin mux and leaves it as the boot loader
set it up, until there is a pin controller driver for that block. On the
Securifi Almond+ the boot loader already leaves the reset button and the
touchscreen interrupt lines in the GPIO function.

The driver used to be part of a series with the interrupt controller,
I2C and watchdog drivers and the device tree changes. That series is now
split per subsystem: the driver builds with COMPILE_TEST and does not
depend on the platform series [2], which is under review separately. The
device tree nodes will follow with the other CS75xx dts changes once the
platform is merged.

There is no public documentation; the register layout comes from the GPL
vendor kernels. Tested on a Securifi Almond+ (CS7542): the reset button
(GPIO 37) works as an active-low gpio-keys input, and the SX8650
touchscreen uses a level-triggered GPIO interrupt.

[1] https://lore.kernel.org/all/20261012-dreamlike-hazily-19bb60326f0a@spud/
[2] https://lore.kernel.org/all/20261114-b4-cs75xx-v7-0-8f17f38821b4@gmail.com/

---
Changes in v4:
- rebase on v7.4-rc1
- split out of "Cortina Systems CS75xx: interrupt controller, GPIO, I2C
  and TWD watchdog" so that each driver can go through its own tree; no
  longer based on the platform series
- the pin mux registers are not part of the GPIO controller (Conor): the
  binding has a single reg entry and the driver no longer switches the
  pin mux when a line is requested
  (Rob, your Reviewed-by on v3 is not carried because of this change)
- switch a line to input for an interrupt only when it is not requested;
  flip the polarity of a both-edges line after the ack, so that an edge
  in between is not lost (sashiko-bot)
- drop the gpio_chip owner, gpiolib sets it; sort the Makefile entry
- Link to v3: https://patch.msgid.link/20261013-b4-cs75xx-s2-v3-0-181bb0d23f4c@gmail.com

Changes in v3:
- rebase on v6 of the platform series
- Link to v2: https://patch.msgid.link/20261013-b4-cs75xx-s2-v2-0-94f8c0a90cda@gmail.com

Changes in v2:
- rebase on v5 of the platform series
- do not include <linux/mod_devicetable.h> (Uwe)
- update the both-edges mask only for a valid trigger type and test it
  under the lock in the interrupt handler; refuse more than 32 lines
  (sashiko-bot)
- Link to v1: https://patch.msgid.link/20261012-b4-cs75xx-s2-v1-0-8a7641b7b79c@gmail.com

To: Linus Walleij <linusw@kernel.org>
To: Bartosz Golaszewski <brgl@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org

---
Fil Dunsky (2):
      dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller
      gpio: Add Cortina Systems CS75xx GPIO driver

 .../bindings/gpio/cortina,cs7542-gpio.yaml         |  65 +++++
 drivers/gpio/Kconfig                               |  12 +
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-cs75xx.c                         | 281 +++++++++++++++++++++
 4 files changed, 359 insertions(+)
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20261015-cs75xx-gpio-ed0a37ee4a68

Best regards,
--  
Fil Dunsky <filipp.dunsky@gmail.com>



^ permalink raw reply	[flat|nested] 4+ messages in thread

end of thread, other threads:[~2026-11-16  2:43 UTC | newest]

Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-16  2:08 [PATCH v4 0/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
2026-11-16  2:08 ` [PATCH v4 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
2026-11-16  2:08 ` [PATCH v4 2/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
2026-11-16  2:42   ` sashiko-bot

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox