* [PATCH net-next v5 0/3] net: phy: report ACx00 receive statistics
@ 2026-11-15 7:45 James Hilliard
2026-11-15 7:45 ` [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name James Hilliard
` (2 more replies)
0 siblings, 3 replies; 11+ messages in thread
From: James Hilliard @ 2026-11-15 7:45 UTC (permalink / raw)
To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller,
Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman,
Jonathan Corbet, Shuah Khan, Randy Dunlap
Cc: Oleksij Rempel, netdev, linux-kernel, James Hilliard, linux-doc
AC200 and AC300 count bytes in received frames including those with CRC
errors. Expose that hardware total through a new optional PHY
rx_bytes_total statistic. The existing successful-byte counter cannot be
derived because the hardware does not separately count damaged-frame
lengths.
Report successful packets and CRC errors through the existing rx_packets
and rx_errors fields. Bracket the raw packet count with matching CRC
counts before subtracting; bytes and CRC errors can still advance when
sustained errors prevent a coherent packet sample.
Assisted-by: Codex:gpt-6-astra
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
---
Changes in v5:
- Split the existing PHY statistics group-name documentation correction
into a separate patch, following Andrew's review.
- Narrow the generic statistics addition to the inclusive receive-byte
counter.
- Derive successful packets from a coherent packet/CRC pair and report
them through the existing rx_packets field.
- Keep collecting CRC errors and inclusive bytes when sustained errors
prevent a coherent pair, with separate baselines and sampling times.
- Skip invalid or unstable byte samples without discarding usable frame
samples, retaining the measured byte modulus and sampling-gap limit.
- Rebase onto current net-next.
- Link to v4: https://patch.msgid.link/20261113-submit-acx00-phy-stats-v1-v4-0-986b8a4a1871@gmail.com
Changes in v4:
- Invalidate the ACx00 baseline before accessing counters in soft_reset,
since phylib may already have reset the hardware before the callback.
- Start a new collection interval on resume and after gaps of at least
320 seconds, including system sleep, preserving collected totals without
interpreting unobserved traffic modulo the hardware counter width.
- Clarify that the byte modulus and frame-byte boundaries were measured
on both AC200 and AC300.
- Specify matching frame-byte boundaries for both PHY byte counters and
explain that phydev corrects the documented name of the existing group.
- Mark the DP83TG720 conversion as unsuitable for automatic stable
selection without the new receive-total API.
- Rebase onto current net-next.
- Link to v3: https://patch.msgid.link/20261109-submit-acx00-phy-stats-v1-v3-0-fbc6327c5be4@gmail.com
Changes in v3:
- Add generic PHY receive-total packet and byte counters in a preparatory
patch, retaining the existing successful-traffic counters and their IDs.
- Report ACx00 packet and byte totals through the new fields, leaving
successful-only counters unset.
- Convert DP83TG720's inclusive RX packet count to the new total field.
- Bound coherent-counter sampling to three attempts and skip unstable
snapshots without making phylib take the link down.
- Reject out-of-range byte samples before updating the hardware baseline
or accumulated totals, retaining MDIO and page-restoration errors.
- Rebase onto current net-next.
- Link to v2: https://patch.msgid.link/20261102-submit-acx00-phy-stats-v1-v2-1-3c8a664407c1@gmail.com
Changes in v2:
- Rebase onto current net-next and repost after the merge window.
- No functional changes.
- Link to v1: https://patch.msgid.link/20261025-submit-acx00-phy-stats-v1-v1-1-d3d461e46db0@gmail.com
To: Andrew Lunn <andrew@lunn.ch>
To: Heiner Kallweit <hkallweit1@gmail.com>
To: Russell King <linux@armlinux.org.uk>
To: "David S. Miller" <davem@davemloft.net>
To: Eric Dumazet <edumazet@kernel.org>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Simon Horman <horms@kernel.org>
To: Jonathan Corbet <corbet@lwn.net>
To: Shuah Khan <skhan@linuxfoundation.org>
To: Randy Dunlap <rdunlap@infradead.org>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-doc@vger.kernel.org
---
James Hilliard (3):
docs: networking: correct the PHY statistics group name
ethtool: add a PHY receive byte total
net: phy: acx00: report receive statistics
Documentation/networking/ethtool-netlink.rst | 15 +-
drivers/net/phy/xpowers/acx00.c | 223 ++++++++++++++++++++++++++-
include/linux/ethtool.h | 8 +-
include/uapi/linux/ethtool_netlink.h | 1 +
net/ethtool/stats.c | 5 +-
5 files changed, 246 insertions(+), 6 deletions(-)
---
base-commit: d1f4b7c6b997c29de67ad7178ababac2328cb1b4
change-id: 20261024-submit-acx00-phy-stats-v1-d838f77444e8
Best regards,
--
James Hilliard <james.hilliard1@gmail.com>
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name 2026-11-15 7:45 [PATCH net-next v5 0/3] net: phy: report ACx00 receive statistics James Hilliard @ 2026-11-15 7:45 ` James Hilliard 2026-11-15 15:01 ` Andrew Lunn 2026-11-15 7:45 ` [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total James Hilliard 2026-11-15 7:45 ` [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics James Hilliard 2 siblings, 1 reply; 11+ messages in thread From: James Hilliard @ 2026-11-15 7:45 UTC (permalink / raw) To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap Cc: Oleksij Rempel, netdev, linux-kernel, James Hilliard, linux-doc The ETHTOOL_STATS_PHY group is exported as phydev by stats_std_names[], but the ethtool netlink documentation lists it as phy. Use the exported name so the documented group matches the statistics string set returned to userspace. Signed-off-by: James Hilliard <james.hilliard1@gmail.com> --- Documentation/networking/ethtool-netlink.rst | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst index eba226c79ec3..8659761ebc69 100644 --- a/Documentation/networking/ethtool-netlink.rst +++ b/Documentation/networking/ethtool-netlink.rst @@ -1665,7 +1665,7 @@ the ``ETHTOOL_A_STATS_GROUPS`` bitset. Currently defined values are: ETHTOOL_STATS_ETH_PHY eth-phy Basic IEEE 802.3 PHY statistics (30.3.2.1.*) ETHTOOL_STATS_ETH_CTRL eth-ctrl Basic IEEE 802.3 MAC Ctrl statistics (30.3.3.*) ETHTOOL_STATS_RMON rmon RMON (RFC 2819) statistics - ETHTOOL_STATS_PHY phy Additional PHY statistics, not defined by IEEE + ETHTOOL_STATS_PHY phydev Additional PHY statistics, not defined by IEEE ====================== ======== =============================================== Each group should have a corresponding ``ETHTOOL_A_STATS_GRP`` in the reply. -- 2.53.0 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name 2026-11-15 7:45 ` [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name James Hilliard @ 2026-11-15 15:01 ` Andrew Lunn 0 siblings, 0 replies; 11+ messages in thread From: Andrew Lunn @ 2026-11-15 15:01 UTC (permalink / raw) To: James Hilliard Cc: Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap, Oleksij Rempel, netdev, linux-kernel, linux-doc On Sun, Nov 15, 2026 at 12:45:45AM -0700, James Hilliard wrote: > The ETHTOOL_STATS_PHY group is exported as phydev by stats_std_names[], > but the ethtool netlink documentation lists it as phy. Use the exported > name so the documented group matches the statistics string set returned > to userspace. > > Signed-off-by: James Hilliard <james.hilliard1@gmail.com> Thanks Reviewed-by: Andrew Lunn <andrew@lunn.ch> Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-15 7:45 [PATCH net-next v5 0/3] net: phy: report ACx00 receive statistics James Hilliard 2026-11-15 7:45 ` [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name James Hilliard @ 2026-11-15 7:45 ` James Hilliard 2026-11-15 15:25 ` Andrew Lunn 2026-11-16 8:06 ` netdev-bot+sashiko 2026-11-15 7:45 ` [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics James Hilliard 2 siblings, 2 replies; 11+ messages in thread From: James Hilliard @ 2026-11-15 7:45 UTC (permalink / raw) To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap Cc: Oleksij Rempel, netdev, linux-kernel, James Hilliard, linux-doc The generic PHY receive-byte counter describes successfully received traffic. Some PHYs instead count bytes in all received frames, including frames with errors. Unlike frame counts, the successful-byte count cannot be derived by subtracting a frame error count because damaged frames have different lengths. Add an optional rx_bytes_total counter to ethtool_phy_stats and the phydev statistics group. Count frame bytes including the Ethernet header, padding and FCS, and excluding the preamble and start frame delimiter. The counter describes reception at the PHY, before MAC or host filtering. Clarify the same byte boundaries for the successful-only receive counter. Append the new attribute so existing statistic IDs and their meanings remain unchanged. Publish its name through the existing statistics string set and retain the unset-counter convention. Signed-off-by: James Hilliard <james.hilliard1@gmail.com> --- Documentation/networking/ethtool-netlink.rst | 13 +++++++++++++ include/linux/ethtool.h | 8 +++++++- include/uapi/linux/ethtool_netlink.h | 1 + net/ethtool/stats.c | 5 ++++- 4 files changed, 25 insertions(+), 2 deletions(-) diff --git a/Documentation/networking/ethtool-netlink.rst b/Documentation/networking/ethtool-netlink.rst index 8659761ebc69..1dad86561823 100644 --- a/Documentation/networking/ethtool-netlink.rst +++ b/Documentation/networking/ethtool-netlink.rst @@ -1683,6 +1683,19 @@ by ``ETHTOOL_A_STATS_GRP_SS_ID``. Complex statistics (such as RMON histogram entries) are also listed inside ``ETHTOOL_A_STATS_GRP`` and do not have a string defined in the string set. +The ``phydev`` group provides separate counters for successfully received +bytes and total received bytes. ``ETHTOOL_A_STATS_PHY_RX_BYTES`` (``RxOctets``) +counts bytes in successfully received frames, while +``ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL`` (``RxOctetsTotal``) also includes bytes +in frames with errors. Both include the Ethernet header, padding and FCS, +but exclude the preamble and start frame delimiter. These counters describe +reception at the PHY, independently of subsequent filtering or drops at +the MAC or host. + +Each counter is optional. Drivers leave unsupported counters at +``ETHTOOL_STAT_NOT_SET``, and the kernel omits them from the reply. A PHY can +report total received bytes even when it cannot separate successful bytes. + RMON "histogram" counters count number of packets within given size range. Because RFC does not specify the ranges beyond the standard 1518 MTU devices differ in definition of buckets. For this reason the definition of packet ranges diff --git a/include/linux/ethtool.h b/include/linux/ethtool.h index c3a41fbd5426..fedc127d9a8a 100644 --- a/include/linux/ethtool.h +++ b/include/linux/ethtool.h @@ -481,11 +481,16 @@ struct ethtool_eth_phy_stats { /** * struct ethtool_phy_stats - PHY-level statistics counters * @rx_packets: Total successfully received frames - * @rx_bytes: Total successfully received bytes + * @rx_bytes: Total successfully received frame bytes. Includes the Ethernet + * header, padding and FCS, but excludes the preamble and start frame + * delimiter. * @rx_errors: Total received frames with errors (e.g., CRC errors) * @tx_packets: Total successfully transmitted frames * @tx_bytes: Total successfully transmitted bytes * @tx_errors: Total transmitted frames with errors + * @rx_bytes_total: Total received frame bytes, including frames with errors. + * Includes the Ethernet header, padding and FCS, but excludes the preamble + * and start frame delimiter. * * This structure provides a standardized interface for reporting * PHY-level statistics counters. It is designed to expose statistics @@ -499,6 +504,7 @@ struct ethtool_phy_stats { u64 tx_packets; u64 tx_bytes; u64 tx_errors; + u64 rx_bytes_total; }; /* Basic IEEE 802.3 MAC Ctrl statistics (30.3.3.*), not otherwise exposed diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h index fa5d645140a4..2e81f7345f72 100644 --- a/include/uapi/linux/ethtool_netlink.h +++ b/include/uapi/linux/ethtool_netlink.h @@ -202,6 +202,7 @@ enum { ETHTOOL_A_STATS_PHY_TX_PKTS, ETHTOOL_A_STATS_PHY_TX_BYTES, ETHTOOL_A_STATS_PHY_TX_ERRORS, + ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL, /* add new constants above here */ __ETHTOOL_A_STATS_PHY_CNT, diff --git a/net/ethtool/stats.c b/net/ethtool/stats.c index 9b0d8cb07675..9b9ada615ac2 100644 --- a/net/ethtool/stats.c +++ b/net/ethtool/stats.c @@ -88,6 +88,7 @@ const char stats_phy_names[__ETHTOOL_A_STATS_PHY_CNT][ETH_GSTRING_LEN] = { [ETHTOOL_A_STATS_PHY_TX_PKTS] = "TxFrames", [ETHTOOL_A_STATS_PHY_TX_BYTES] = "TxOctets", [ETHTOOL_A_STATS_PHY_TX_ERRORS] = "TxErrors", + [ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL] = "RxOctetsTotal", }; const struct nla_policy ethnl_stats_get_policy[ETHTOOL_A_STATS_SRC + 1] = { @@ -295,7 +296,9 @@ static int stats_put_phydev_stats(struct sk_buff *skb, stat_put(skb, ETHTOOL_A_STATS_PHY_TX_BYTES, data->phydev_stats.tx_bytes) || stat_put(skb, ETHTOOL_A_STATS_PHY_TX_ERRORS, - data->phydev_stats.tx_errors)) + data->phydev_stats.tx_errors) || + stat_put(skb, ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL, + data->phydev_stats.rx_bytes_total)) return -EMSGSIZE; return 0; } -- 2.53.0 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-15 7:45 ` [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total James Hilliard @ 2026-11-15 15:25 ` Andrew Lunn 2026-11-16 4:12 ` James Hilliard 2026-11-16 8:06 ` netdev-bot+sashiko 1 sibling, 1 reply; 11+ messages in thread From: Andrew Lunn @ 2026-11-15 15:25 UTC (permalink / raw) To: James Hilliard Cc: Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap, Oleksij Rempel, netdev, linux-kernel, linux-doc On Sun, Nov 15, 2026 at 12:45:46AM -0700, James Hilliard wrote: > The generic PHY receive-byte counter describes successfully received > traffic. Some PHYs instead count bytes in all received frames, > including frames with errors. In the general case, that is wrong. A PHY basically does digital to analogue conversion. It takes a stream of bit from the MAC and converts them to analogue signals on the media. In the opposite direction, it recovers the analogue signals, converts it to digital, and passes it to the MAC. Thinks about SGMII. When running to 10Mbps, the MAC has to duplicate the bits 100 times. At 100Mbps, it duplicates the bits 10 times. The PHY then puts the bits onto the wire, it has no need to understand the duplication, the boundary between the MAC level bits, it is just a dumb DAC/ADC. In order to see frames, not a stream of bits, you need a MAC. Now, some PHYs do in fact have MACs. Those that implement PTP for example need to reassemble the bit stream into frames. Anything which does MACSEC. Or rate adaptation. But in the general case, its just a stream of bits. And the byte counters should be for the general case. And for SGMII, the definition is a bit more fuzzy, does it include the repetition or not? If the PHY has a MAC, it can additionally fill in the frame counters. Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-15 15:25 ` Andrew Lunn @ 2026-11-16 4:12 ` James Hilliard 2026-11-16 4:39 ` Andrew Lunn 0 siblings, 1 reply; 11+ messages in thread From: James Hilliard @ 2026-11-16 4:12 UTC (permalink / raw) To: Andrew Lunn Cc: Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap, Oleksij Rempel, netdev, linux-kernel, linux-doc On Sun, Nov 15, 2026 at 8:25 AM Andrew Lunn <andrew@lunn.ch> wrote: > > On Sun, Nov 15, 2026 at 12:45:46AM -0700, James Hilliard wrote: > > > The generic PHY receive-byte counter describes successfully received > > traffic. Some PHYs instead count bytes in all received frames, > > including frames with errors. That restriction comes from the current kernel-doc definition of ethtool_phy_stats.rx_bytes: "Total successfully received bytes". It was the reason for introducing a separate inclusive byte counter. I checked the PHY statistics callbacks in net-next and couldn't find any driver populating rx_bytes. The original series [0] introduced the byte fields, but its initial drivers only populated packet and error counters. > > In the general case, that is wrong. A PHY basically does digital to > analogue conversion. It takes a stream of bit from the MAC and > converts them to analogue signals on the media. In the opposite > direction, it recovers the analogue signals, converts it to digital, > and passes it to the MAC. > > Thinks about SGMII. When running to 10Mbps, the MAC has to duplicate > the bits 100 times. At 100Mbps, it duplicates the bits 10 times. The > PHY then puts the bits onto the wire, it has no need to understand the > duplication, the boundary between the MAC level bits, it is just a > dumb DAC/ADC. > > In order to see frames, not a stream of bits, you need a MAC. > > Now, some PHYs do in fact have MACs. Those that implement PTP for > example need to reassemble the bit stream into frames. Anything which > does MACSEC. Or rate adaptation. > > But in the general case, its just a stream of bits. And the byte > counters should be for the general case. And for SGMII, the definition > is a bit more fuzzy, does it include the repetition or not? Should we instead clarify the existing rx_bytes definition to include errored traffic and use it for ACx00, dropping rx_bytes_total? That would leave the existing packet counters unchanged. For ACx00, the byte counter includes FCS and bytes from CRC-bad frames. We also tested at 10 and 100 Mb/s over RMII: the byte counts showed no tenfold inflation at 10 Mb/s despite its repeated interface cycles. [0] https://lore.kernel.org/r/20250110060517.711683-1-o.rempel@pengutronix.de/ > > If the PHY has a MAC, it can additionally fill in the frame counters. > > Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-16 4:12 ` James Hilliard @ 2026-11-16 4:39 ` Andrew Lunn 2026-11-16 4:56 ` James Hilliard 0 siblings, 1 reply; 11+ messages in thread From: Andrew Lunn @ 2026-11-16 4:39 UTC (permalink / raw) To: James Hilliard Cc: Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap, Oleksij Rempel, netdev, linux-kernel, linux-doc On Sun, Nov 15, 2026 at 09:12:35PM -0700, James Hilliard wrote: > On Sun, Nov 15, 2026 at 8:25 AM Andrew Lunn <andrew@lunn.ch> wrote: > > > > On Sun, Nov 15, 2026 at 12:45:46AM -0700, James Hilliard wrote: > > > > > The generic PHY receive-byte counter describes successfully received > > > traffic. Some PHYs instead count bytes in all received frames, > > > including frames with errors. > > That restriction comes from the current kernel-doc definition of > ethtool_phy_stats.rx_bytes: "Total successfully received bytes". Yes, i found this. > Should we instead clarify the existing rx_bytes definition to include > errored traffic and use it for ACx00, dropping rx_bytes_total? That > would leave the existing packet counters unchanged. What do you mean by errored traffic? Think about it. If you don't have a MAC, you don't have FCS. Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-16 4:39 ` Andrew Lunn @ 2026-11-16 4:56 ` James Hilliard 0 siblings, 0 replies; 11+ messages in thread From: James Hilliard @ 2026-11-16 4:56 UTC (permalink / raw) To: Andrew Lunn Cc: Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap, Oleksij Rempel, netdev, linux-kernel, linux-doc On Sun, Nov 15, 2026 at 9:39 PM Andrew Lunn <andrew@lunn.ch> wrote: > > On Sun, Nov 15, 2026 at 09:12:35PM -0700, James Hilliard wrote: > > On Sun, Nov 15, 2026 at 8:25 AM Andrew Lunn <andrew@lunn.ch> wrote: > > > > > > On Sun, Nov 15, 2026 at 12:45:46AM -0700, James Hilliard wrote: > > > > > > > The generic PHY receive-byte counter describes successfully received > > > > traffic. Some PHYs instead count bytes in all received frames, > > > > including frames with errors. > > > > That restriction comes from the current kernel-doc definition of > > ethtool_phy_stats.rx_bytes: "Total successfully received bytes". > > Yes, i found this. > > > Should we instead clarify the existing rx_bytes definition to include > > errored traffic and use it for ACx00, dropping rx_bytes_total? That > > would leave the existing packet counters unchanged. > > What do you mean by errored traffic? Specifically, frames with an invalid Ethernet FCS. ACx00 has a PHY-resident CRC-error counter, and its received-byte counter includes bytes from those frames. We checked this using PHY loopback with MAC FCS insertion disabled. Frames with a software-generated valid FCS did not increment the PHY CRC-error counter; flipping one FCS bit did. These observations came from the PHY registers read over MDIO, not from MAC statistics. > > Think about it. > > If you don't have a MAC, you don't have FCS. There are existing mainline PHY drivers exposing this functionality. The QCA807x/QCA808x drivers use qcom_phy_counter_config() to enable CRC checking, and qcom_phy_get_stats() reports the RX CRC-error count through ethtool_phy_stats.rx_errors [0]. The IP101G driver also exposes a phy_crc_errors counter separately from phy_symbol_errors [1]. This demonstrates frame-aware diagnostic functionality within these PHYs, rather than something every PHY necessarily implements. The generic byte counter need not require that functionality. My question was whether rx_bytes should count received bytes without conditioning the count on FCS validity. ACx00 could then report its hardware byte total through that field, including bytes from frames which its separate CRC checker identifies as bad. [0] https://github.com/torvalds/linux/blob/v7.4-rc3/drivers/net/phy/qcom/qcom-phy-lib.c [1] https://github.com/torvalds/linux/blob/v7.4-rc3/drivers/net/phy/icplus.c > > Andrew ^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total 2026-11-15 7:45 ` [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total James Hilliard 2026-11-15 15:25 ` Andrew Lunn @ 2026-11-16 8:06 ` netdev-bot+sashiko 1 sibling, 0 replies; 11+ messages in thread From: netdev-bot+sashiko @ 2026-11-16 8:06 UTC (permalink / raw) To: james.hilliard1 Cc: andrew, hkallweit1, linux, davem, edumazet, kuba, pabeni, horms, corbet, skhan, rdunlap, o.rempel, netdev, linux-kernel, linux-doc Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider. Critical: 0 · High: 0 · Medium: 1 · Low: 0 If you believe none of the issues are legitimate, please reply to each issue of Medium severity or higher and explain why the AI is wrong. If any of them are legitimate and you plan to respin, please let patchwork know by including "pw-bot: cr" as a separate line at the end of your reply (one such reply per series is enough). - [Medium] ethtool: unagreed UAPI addition of ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL -- > diff --git a/include/uapi/linux/ethtool_netlink.h b/include/uapi/linux/ethtool_netlink.h > --- a/include/uapi/linux/ethtool_netlink.h > +++ b/include/uapi/linux/ethtool_netlink.h > @@ -202,6 +202,7 @@ enum { > ETHTOOL_A_STATS_PHY_TX_PKTS, > ETHTOOL_A_STATS_PHY_TX_BYTES, > ETHTOOL_A_STATS_PHY_TX_ERRORS, > + ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL, > > /* add new constants above here */ > __ETHTOOL_A_STATS_PHY_CNT, [Severity: Medium] This patch adds three things: - ETHTOOL_A_STATS_PHY_RX_BYTES_TOTAL to the uAPI enum - a new RxOctetsTotal entry in stats_phy_names[] - rx_bytes_total in struct ethtool_phy_stats Once this ships, the attribute and the string are uAPI. We cannot change or remove them later. On v3, Andrew and Oleksij both objected to adding generic PHY counters just because the ACx00 happens to expose the registers. They asked for a concrete use case. v5 drops the packet total by deriving it in the driver, but the byte total is still here. I don't see that use case answered in the commit message. What does user space do with RxOctetsTotal that it cannot already do with RxOctets, RxErrors and the MAC level counters? The patch also rewrites the kernel-doc for the existing rx_bytes field. It now says the count includes header, padding and FCS, and excludes preamble and SFD. That narrows the meaning of a counter drivers already report through stats_put_phydev_stats(). Two questions on that: - Have the drivers that already fill phydev_stats.rx_bytes been checked against the new definition? - What should a PHY that counts preamble/SFD, or uses some other boundary, do? Leave both counters at ETHTOOL_STAT_NOT_SET, or report a value that doesn't match the documented semantics? I'd like the PHY maintainers to agree on the semantics before this goes in. If ACx00 is the only user, could the errored-frame byte total stay a PHY driver private statistic for now? -- Sashiko AI review · https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20261115-submit-acx00-phy-stats-v1-v5-0-ed81a7f54373%40gmail.com ^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics 2026-11-15 7:45 [PATCH net-next v5 0/3] net: phy: report ACx00 receive statistics James Hilliard 2026-11-15 7:45 ` [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name James Hilliard 2026-11-15 7:45 ` [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total James Hilliard @ 2026-11-15 7:45 ` James Hilliard 2026-11-16 8:06 ` netdev-bot+sashiko 2 siblings, 1 reply; 11+ messages in thread From: James Hilliard @ 2026-11-15 7:45 UTC (permalink / raw) To: Andrew Lunn, Heiner Kallweit, Russell King, David S. Miller, Eric Dumazet, Jakub Kicinski, Paolo Abeni, Simon Horman, Jonathan Corbet, Shuah Khan, Randy Dunlap Cc: Oleksij Rempel, netdev, linux-kernel, James Hilliard, linux-doc AC200 and AC300 count received frames including those with CRC errors. Subtract the CRC-error count to report successful frames through the existing PHY rx_packets statistic, and report CRC errors through rx_errors. Report the hardware byte total through rx_bytes_total, leaving the successful-only rx_bytes unset because damaged-frame lengths are not available separately. The free-running packet and CRC-error counters both wrap at 2^32. Read each counter high/low/high to detect a carry, and bracket the packet read with an unchanged CRC count before subtracting. Their difference also wraps at 2^32. Accumulate its wrap-adjusted deltas in a 64-bit total. Hardware measurements on AC200 and AC300 established a receive-byte modulus of 4,000,000,000. The byte counts include Ethernet headers, padding and FCS, but exclude preamble and SFD. Apply that modulus to byte deltas and skip byte samples at or above it without changing their baseline. Bound sampling retries to avoid retaining the PHY and MDIO locks indefinitely. When CRC errors keep arriving, update rx_errors from the latest stable error read without advancing the successful-frame baseline. A later coherent pair accounts for the intervening successful frames. Collect bytes independently of that pair. An unstable sample is not an MDIO error: returning a synthetic error from update_stats would make phylib take the link down. Real MDIO errors, including page-restoration failures, still propagate. Serialize sampling, reporting and power transitions with the package mutex. Commit samples only after page restoration succeeds, and return cached totals from get_phy_stats without further MDIO access. Invalidate baselines before soft_reset or power-off, since phylib may already have reset the counters. Take a best-effort snapshot before suspend and start new intervals on resume, including when WoL retained power while polling stopped. Keep a separate sampling time for each counter and discard deltas after gaps of at least 320 seconds, including system sleep and register-read time. At 100 Mb/s, that bounds the byte counter and conservatively bounds the frame counters even at one frame per received byte. Retain accumulated totals across these gaps and power transitions, without inventing an unobservable number of counter cycles. Signed-off-by: James Hilliard <james.hilliard1@gmail.com> --- drivers/net/phy/xpowers/acx00.c | 223 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 220 insertions(+), 3 deletions(-) diff --git a/drivers/net/phy/xpowers/acx00.c b/drivers/net/phy/xpowers/acx00.c index cee6c7ff0278..691f4931af46 100644 --- a/drivers/net/phy/xpowers/acx00.c +++ b/drivers/net/phy/xpowers/acx00.c @@ -8,12 +8,14 @@ #include <linux/bitfield.h> #include <linux/device.h> +#include <linux/ethtool.h> #include <linux/module.h> #include <linux/mutex.h> #include <linux/nvmem-consumer.h> #include <linux/of.h> #include <linux/phy.h> #include <linux/slab.h> +#include <linux/timekeeping.h> #include "../phylib.h" #include "acx00.h" @@ -31,6 +33,7 @@ #define ACX00_PAGE_2 2 #define ACX00_PAGE_6 6 #define ACX00_PAGE_8 8 +#define ACX00_PAGE_9 9 #define ACX00_PAGE0_GLOBAL_CONFIG_REG 0x13 #define ACX00_PAGE0_XMII_RX_CLOCK_INVERT BIT(12) @@ -76,6 +79,26 @@ (ACX00_PAGE8_AUTO_CAL_TX_LEVEL_ADJUST_BYPASS | \ ACX00_PAGE8_AUTO_CAL_LOW_CAL_OPAQUE_BITS) +#define ACX00_PAGE9_RX_BYTES_HIGH_REG 0x19 +#define ACX00_PAGE9_RX_PACKETS_HIGH_REG 0x1b +#define ACX00_PAGE9_RX_CRC_ERRORS_HIGH_REG 0x1d + +/* + * AC200 and AC300 hardware testing confirmed that the receive byte counter + * wraps at 4,000,000,000 rather than 2^32. + */ +#define ACX00_RX_BYTES_WRAP 4000000000ULL +/* At 100 Mb/s, a full byte-counter cycle takes at least 320 seconds. */ +#define ACX00_STATS_MAX_INTERVAL_MS (ACX00_RX_BYTES_WRAP * 8 / (SPEED_100 * 1000)) +#define ACX00_COUNTER_READ_ATTEMPTS 3 + +enum acx00_ephy_stat { + ACX00_STAT_RX_PACKETS, + ACX00_STAT_RX_CRC_ERRORS, + ACX00_STAT_RX_BYTES, + ACX00_NUM_STATS, +}; + /* * Another integration of this exact-ID PHY documents its digital vendor * register map, which also matches the observed ACx00 reset values. The ACx00 @@ -86,11 +109,16 @@ struct acx00_ephy_priv { struct phy_device *phydev; struct acx00_ephy_control *control; - /* Serializes package state and multi-register power sequences. */ + /* Serializes package state, power sequences and statistics. */ struct mutex state_lock; bool is_ac300; bool use_low_calibration_tuning; bool xmii_rx_clock_inverted; + bool stats_active; + u8 stats_valid; + ktime_t stats_start[ACX00_NUM_STATS]; + u32 stats_last[ACX00_NUM_STATS]; + u64 stats[ACX00_NUM_STATS]; }; static int acx00_ephy_read_page(struct phy_device *phydev) @@ -110,6 +138,169 @@ static int acx00_ephy_write_page(struct phy_device *phydev, int page) FIELD_PREP(ACX00_PAGE_SELECT_MASK, page)); } +/* Return 0 on success, 1 for an unstable sample, or a negative MDIO error. */ +static int acx00_ephy_read_counter(struct phy_device *phydev, u8 reg, u32 *count) +{ + int high, low, check; + int i; + + /* The free-running counter can carry while its two halves are read. */ + for (i = 0; i < ACX00_COUNTER_READ_ATTEMPTS; i++) { + high = __phy_read(phydev, reg); + if (high < 0) + return high; + low = __phy_read(phydev, reg + 1); + if (low < 0) + return low; + check = __phy_read(phydev, reg); + if (check < 0) + return check; + if (high != check) + continue; + + *count = (u32)high << 16 | low; + return 0; + } + + return 1; +} + +/* Return a mask of usable counters, or a negative MDIO error. */ +static int acx00_ephy_read_counts(struct phy_device *phydev, u32 *counts) +{ + u32 packets, errors; + int ret; + int i; + + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_CRC_ERRORS_HIGH_REG, + &counts[ACX00_STAT_RX_CRC_ERRORS]); + if (ret) + return ret < 0 ? ret : 0; + + /* Bracket the packet counter with an unchanged CRC count. */ + for (i = 0; i < ACX00_COUNTER_READ_ATTEMPTS; i++) { + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_PACKETS_HIGH_REG, + &packets); + if (ret < 0) + return ret; + if (ret) + break; + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_CRC_ERRORS_HIGH_REG, + &errors); + if (ret < 0) + return ret; + if (ret) + break; + if (errors == counts[ACX00_STAT_RX_CRC_ERRORS]) { + /* Both hardware counters and their difference wrap at 2^32. */ + counts[ACX00_STAT_RX_PACKETS] = packets - errors; + return BIT(ACX00_STAT_RX_PACKETS) | BIT(ACX00_STAT_RX_CRC_ERRORS); + } + counts[ACX00_STAT_RX_CRC_ERRORS] = errors; + } + + /* Keep reporting errors even when no coherent packet sample is possible. */ + return BIT(ACX00_STAT_RX_CRC_ERRORS); +} + +static int __acx00_ephy_update_stats(struct phy_device *phydev) +{ + struct acx00_ephy_priv *priv = phydev->priv; + u32 counts[ACX00_NUM_STATS]; + ktime_t start; + int oldpage; + int valid; + int ret; + int i; + + lockdep_assert_held(&priv->state_lock); + + if (!priv->stats_active) + return 0; + + start = ktime_get_boottime(); + oldpage = phy_select_page(phydev, ACX00_PAGE_9); + if (oldpage < 0) + return phy_restore_page(phydev, oldpage, oldpage); + + valid = acx00_ephy_read_counts(phydev, counts); + if (valid < 0) { + ret = valid; + goto out_restore_page; + } + + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_BYTES_HIGH_REG, + &counts[ACX00_STAT_RX_BYTES]); + if (ret < 0) + goto out_restore_page; + if (!ret && counts[ACX00_STAT_RX_BYTES] < ACX00_RX_BYTES_WRAP) + valid |= BIT(ACX00_STAT_RX_BYTES); + ret = valid; + +out_restore_page: + ret = phy_restore_page(phydev, oldpage, ret); + if (ret < 0) + return ret; + + for (i = 0; i < ACX00_NUM_STATS; i++) { + u64 count; + + if (!(ret & BIT(i))) + continue; + count = counts[i]; + + /* Include sleep and read time; unseen cycles cannot be recovered. */ + if ((priv->stats_valid & BIT(i)) && + ktime_ms_delta(ktime_get_boottime(), priv->stats_start[i]) < + (s64)ACX00_STATS_MAX_INTERVAL_MS) { + if (count < priv->stats_last[i]) + count += i == ACX00_STAT_RX_BYTES ? + ACX00_RX_BYTES_WRAP : BIT_ULL(32); + priv->stats[i] += count - priv->stats_last[i]; + } + priv->stats_last[i] = counts[i]; + priv->stats_start[i] = start; + priv->stats_valid |= BIT(i); + } + + return 0; +} + +static int acx00_ephy_update_stats(struct phy_device *phydev) +{ + struct acx00_ephy_priv *priv = phydev->priv; + int ret; + + mutex_lock(&priv->state_lock); + ret = __acx00_ephy_update_stats(phydev); + mutex_unlock(&priv->state_lock); + + return ret; +} + +static void acx00_ephy_get_phy_stats(struct phy_device *phydev, + struct ethtool_eth_phy_stats *eth_stats, + struct ethtool_phy_stats *stats) +{ + struct acx00_ephy_priv *priv = phydev->priv; + + mutex_lock(&priv->state_lock); + stats->rx_packets = priv->stats[ACX00_STAT_RX_PACKETS]; + stats->rx_errors = priv->stats[ACX00_STAT_RX_CRC_ERRORS]; + stats->rx_bytes_total = priv->stats[ACX00_STAT_RX_BYTES]; + mutex_unlock(&priv->state_lock); +} + +static void acx00_ephy_snapshot_stats(struct phy_device *phydev) +{ + int ret; + + /* Statistics collection must not prevent reset or power management. */ + ret = __acx00_ephy_update_stats(phydev); + if (ret) + phydev_dbg(phydev, "failed to snapshot statistics: %pe\n", ERR_PTR(ret)); +} + static int acx00_ephy_control_power_on(struct acx00_ephy_priv *priv) { lockdep_assert_held(&priv->state_lock); @@ -122,6 +313,10 @@ static int acx00_ephy_control_power_off(struct acx00_ephy_priv *priv) { lockdep_assert_held(&priv->state_lock); + /* Even a failed power-off can have reset the hardware counter. */ + priv->stats_active = false; + priv->stats_valid = 0; + return priv->control->power_off(priv->control); } @@ -350,6 +545,10 @@ static int acx00_ephy_soft_reset(struct phy_device *phydev) mutex_lock(&priv->state_lock); + /* phylib may already have reset the counters before calling us. */ + priv->stats_active = false; + priv->stats_valid = 0; + ret = acx00_ephy_set_interface(phydev); if (ret) goto out_power_off; @@ -475,10 +674,21 @@ static int __acx00_ephy_config_init(struct phy_device *phydev) /* Restore the standard EEE policy retained by phylib across resets. */ ret = genphy_c45_an_config_eee_aneg(phydev); - if (ret <= 0) + if (ret < 0) return ret; + if (ret > 0) { + ret = genphy_restart_aneg(phydev); + if (ret) + return ret; + } + + if (!priv->stats_active) { + /* Establish a new baseline after reset, retaining the software total. */ + priv->stats_active = true; + acx00_ephy_snapshot_stats(phydev); + } - return genphy_restart_aneg(phydev); + return 0; } static int acx00_ephy_config_init(struct phy_device *phydev) @@ -534,6 +744,9 @@ static int acx00_ephy_resume(struct phy_device *phydev) int ret; mutex_lock(&priv->state_lock); + /* WoL can keep the PHY counting while phylib polling is stopped. */ + priv->stats_active = false; + priv->stats_valid = 0; ret = __acx00_ephy_power_on_and_resume(phydev); mutex_unlock(&priv->state_lock); @@ -550,6 +763,8 @@ static int acx00_ephy_suspend(struct phy_device *phydev) mutex_lock(&phydev->lock); mutex_lock(&priv->state_lock); + acx00_ephy_snapshot_stats(phydev); + ret = genphy_suspend(phydev); if (ret) goto out_unlock; @@ -616,6 +831,8 @@ static struct phy_driver acx00_ephy_driver[] = { .soft_reset = acx00_ephy_soft_reset, .config_init = acx00_ephy_config_init, .disable_autonomous_eee = acx00_ephy_disable_autonomous_eee, + .get_phy_stats = acx00_ephy_get_phy_stats, + .update_stats = acx00_ephy_update_stats, .suspend = acx00_ephy_suspend, .resume = acx00_ephy_resume, }, -- 2.53.0 ^ permalink raw reply related [flat|nested] 11+ messages in thread
* Re: [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics 2026-11-15 7:45 ` [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics James Hilliard @ 2026-11-16 8:06 ` netdev-bot+sashiko 0 siblings, 0 replies; 11+ messages in thread From: netdev-bot+sashiko @ 2026-11-16 8:06 UTC (permalink / raw) To: james.hilliard1 Cc: andrew, hkallweit1, linux, davem, edumazet, kuba, pabeni, horms, corbet, skhan, rdunlap, o.rempel, netdev, linux-kernel, linux-doc Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider. Critical: 0 · High: 0 · Medium: 1 · Low: 1 If you believe none of the issues are legitimate, please reply to each issue of Medium severity or higher and explain why the AI is wrong. If any of them are legitimate and you plan to respin, please let patchwork know by including "pw-bot: cr" as a separate line at the end of your reply (one such reply per series is enough). - [Medium] rx_packets permanently loses successful frames when CRC errors keep breaking the bracket for 320 s or more. - [Low] Speculative, depends on undocumented counter behaviour. -- net: phy: acx00: report receive statistics This adds update_stats and get_phy_stats support to the AC200/AC300 EPHY driver. Successful frames (frame count minus CRC errors) go to rx_packets, CRC errors go to rx_errors, and the hardware byte count goes to rx_bytes_total. The hardware counters are sampled with carry detection and a CRC-bracketed packet read. Wrap-adjusted deltas are added to 64-bit totals, and a delta is discarded when 320 seconds or more have passed since that counter was last sampled. > diff --git a/drivers/net/phy/xpowers/acx00.c b/drivers/net/phy/xpowers/acx00.c > index cee6c7ff0278e..691f4931af460 100644 > --- a/drivers/net/phy/xpowers/acx00.c > +++ b/drivers/net/phy/xpowers/acx00.c [ ... ] > @@ -110,6 +138,169 @@ static int acx00_ephy_write_page(struct phy_device *phydev, int page) [ ... ] > +/* Return a mask of usable counters, or a negative MDIO error. */ > +static int acx00_ephy_read_counts(struct phy_device *phydev, u32 *counts) > +{ [ ... ] > + /* Bracket the packet counter with an unchanged CRC count. */ > + for (i = 0; i < ACX00_COUNTER_READ_ATTEMPTS; i++) { > + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_PACKETS_HIGH_REG, > + &packets); > + if (ret < 0) > + return ret; > + if (ret) > + break; > + ret = acx00_ephy_read_counter(phydev, ACX00_PAGE9_RX_CRC_ERRORS_HIGH_REG, > + &errors); > + if (ret < 0) > + return ret; > + if (ret) > + break; > + if (errors == counts[ACX00_STAT_RX_CRC_ERRORS]) { > + /* Both hardware counters and their difference wrap at 2^32. */ > + counts[ACX00_STAT_RX_PACKETS] = packets - errors; > + return BIT(ACX00_STAT_RX_PACKETS) | BIT(ACX00_STAT_RX_CRC_ERRORS); > + } > + counts[ACX00_STAT_RX_CRC_ERRORS] = errors; > + } > + > + /* Keep reporting errors even when no coherent packet sample is possible. */ > + return BIT(ACX00_STAT_RX_CRC_ERRORS); > +} [Severity: Medium] Can rx_packets permanently lose successful frames when CRC errors keep breaking the bracket? On this path only the CRC bit is returned. __acx00_ephy_update_stats() therefore leaves stats_last[ACX00_STAT_RX_PACKETS] and stats_start[ACX00_STAT_RX_PACKETS] at their values from the last coherent pair, while rx_errors keeps advancing. When a coherent pair finally arrives, its delta is only accepted if: if ((priv->stats_valid & BIT(i)) && ktime_ms_delta(ktime_get_boottime(), priv->stats_start[i]) < (s64)ACX00_STATS_MAX_INTERVAL_MS) { Suppose the CRC count changes in all three bracket windows on every poll for 320 seconds or more. One example is a bulk transfer over a damaged cable with a few thousand CRC errors per second. In that case only the baseline moves, and every successful frame received since the last coherent pair is dropped from rx_packets. rx_errors stays correct, so the reported error ratio comes out wrong. ACX00_STATS_MAX_INTERVAL_MS comes from the byte counter's 4,000,000,000 modulus. The 2^32 packets-minus-errors difference cannot wrap at 100 Mb/s for about 8 hours (2^32 / 148,810 minimum-size frames/s is roughly 28,862 s). The dropped delta could still have been recovered. The commit message says: When CRC errors keep arriving, update rx_errors from the latest stable error read without advancing the successful-frame baseline. A later coherent pair accounts for the intervening successful frames. Is that only true when the incoherent period is shorter than 320 seconds? Would a separate interval limit for the frame counters, based on their 2^32 modulus, avoid dropping these frames? > + > +static int __acx00_ephy_update_stats(struct phy_device *phydev) > +{ [ ... ] > + for (i = 0; i < ACX00_NUM_STATS; i++) { > + u64 count; > + > + if (!(ret & BIT(i))) > + continue; > + count = counts[i]; > + > + /* Include sleep and read time; unseen cycles cannot be recovered. */ > + if ((priv->stats_valid & BIT(i)) && > + ktime_ms_delta(ktime_get_boottime(), priv->stats_start[i]) < > + (s64)ACX00_STATS_MAX_INTERVAL_MS) { > + if (count < priv->stats_last[i]) > + count += i == ACX00_STAT_RX_BYTES ? > + ACX00_RX_BYTES_WRAP : BIT_ULL(32); > + priv->stats[i] += count - priv->stats_last[i]; > + } [Severity: Low] This depends on counter behaviour that isn't documented. What happens if the difference computed in acx00_ephy_read_counts() goes down between two samples? counts[ACX00_STAT_RX_PACKETS] = packets - errors; This code treats any drop as a 2^32 wrap, so rx_packets would jump by about 4.29e9. Totals are kept across resets and power transitions, so the jump would be permanent. The difference only stays non-decreasing if two things hold. The frame counter must include every event the CRC-error counter counts. It must also never increment later than the CRC counter for the same frame. The bracket only shows that the CRC count didn't change while the packet counter was being read. Two hardware behaviours would break this: - The CRC/error counter also counts events the frame counter skips, such as runts, collision fragments, false carrier or RX_ER. - The frame counter increments at start of frame and the CRC counter at end of frame. At 10 Mb/s these can be up to about 1.2 ms apart. If no good frame arrives before the next poll, the difference drops by 1. Intervals are already limited to under 320 seconds. At 100 Mb/s at most about 47.6 million frames can arrive in that time. Could a wrap-adjusted packet delta larger than that be rejected and used as a new baseline, rather than added to the total? -- Sashiko AI review · https://netdev-ai.bots.linux.dev/sashiko/#/patchset/20261115-submit-acx00-phy-stats-v1-v5-0-ed81a7f54373%40gmail.com ^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2026-11-16 8:06 UTC | newest] Thread overview: 11+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2026-11-15 7:45 [PATCH net-next v5 0/3] net: phy: report ACx00 receive statistics James Hilliard 2026-11-15 7:45 ` [PATCH net-next v5 1/3] docs: networking: correct the PHY statistics group name James Hilliard 2026-11-15 15:01 ` Andrew Lunn 2026-11-15 7:45 ` [PATCH net-next v5 2/3] ethtool: add a PHY receive byte total James Hilliard 2026-11-15 15:25 ` Andrew Lunn 2026-11-16 4:12 ` James Hilliard 2026-11-16 4:39 ` Andrew Lunn 2026-11-16 4:56 ` James Hilliard 2026-11-16 8:06 ` netdev-bot+sashiko 2026-11-15 7:45 ` [PATCH net-next v5 3/3] net: phy: acx00: report receive statistics James Hilliard 2026-11-16 8:06 ` netdev-bot+sashiko
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox