* [PATCHv3 22/41] ARM: omap2.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP2 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap2.dtsi | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index d0c5b37e248c..af3531cc4576 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -271,5 +271,36 @@
ti,hwmods = "timer12";
ti,timer-pwm;
};
+
+ dss: dss@48050000 {
+ compatible = "ti,omap2-dss", "simple-bus";
+ reg = <0x48050000 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@48050400 {
+ compatible = "ti,omap2-dispc";
+ reg = <0x48050400 0x400>;
+ interrupts = <25>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ rfbi: encoder@48050800 {
+ compatible = "ti,omap2-rfbi";
+ reg = <0x48050800 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@48050c00 {
+ compatible = "ti,omap2-venc";
+ reg = <0x48050c00 0x400>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 23/41] ARM: omap3.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3.dtsi | 42 ++++++++++++++++++++++++++++++++++++++++++
1 file changed, 42 insertions(+)
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index daabf99d402a..d942f9a4723f 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -630,5 +630,47 @@
num-eps = <16>;
ram-bits = <12>;
};
+
+ dss: dss@48050000 {
+ compatible = "ti,omap3-dss", "simple-bus";
+ reg = <0x48050000 0x200>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@48050400 {
+ compatible = "ti,omap3-dispc";
+ reg = <0x48050400 0x400>;
+ interrupts = <25>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ dsi: encoder@4804fc00 {
+ compatible = "ti,omap3-dsi";
+ reg = <0x4804fc00 0x200>,
+ <0x4804fe00 0x40>,
+ <0x4804ff00 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <25>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi1";
+ };
+
+ rfbi: encoder@48050800 {
+ compatible = "ti,omap3-rfbi";
+ reg = <0x48050800 0x100>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@48050c00 {
+ compatible = "ti,omap3-venc";
+ reg = <0x48050c00 0x100>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 24/41] ARM: omap4.dtsi: add omapdss information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4.dtsi | 65 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index a1e05853afcd..19498b2fa316 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -705,5 +705,70 @@
dmas = <&sdma 117>, <&sdma 116>;
dma-names = "tx", "rx";
};
+
+ dss: dss@58000000 {
+ compatible = "ti,omap4-dss", "simple-bus";
+ reg = <0x58000000 0x80>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@58001000 {
+ compatible = "ti,omap4-dispc";
+ reg = <0x58001000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ rfbi: encoder@58002000 {
+ compatible = "ti,omap4-rfbi";
+ reg = <0x58002000 0x1000>;
+ status = "disabled";
+ ti,hwmods = "dss_rfbi";
+ };
+
+ venc: encoder@58003000 {
+ compatible = "ti,omap4-venc";
+ reg = <0x58003000 0x1000>;
+ status = "disabled";
+ ti,hwmods = "dss_venc";
+ };
+
+ dsi1: encoder@58004000 {
+ compatible = "ti,omap4-dsi";
+ reg = <0x58004000 0x200>,
+ <0x58004200 0x40>,
+ <0x58004300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi1";
+ };
+
+ dsi2: encoder@58005000 {
+ compatible = "ti,omap4-dsi";
+ reg = <0x58005000 0x200>,
+ <0x58005200 0x40>,
+ <0x58005300 0x20>;
+ reg-names = "proto", "phy", "pll";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_dsi2";
+ };
+
+ hdmi: encoder@58006000 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0x58006000 0x200>,
+ <0x58006200 0x100>,
+ <0x58006300 0x100>,
+ <0x58006400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_hdmi";
+ };
+ };
};
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 25/41] ARM: omap4-panda.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 Pandaboard. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4-panda-common.dtsi | 119 +++++++++++++++++++++++++++++-
1 file changed, 115 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 88c6a05cab41..20aa18ff4823 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -16,6 +16,11 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &hdmi0;
+ };
+
leds: leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -104,6 +109,87 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
};
&omap4_pmx_core {
@@ -112,10 +198,6 @@
&twl6040_pins
&mcpdm_pins
&mcbsp1_pins
- &dss_dpi_pins
- &tfp410_pins
- &dss_hdmi_pins
- &tpd12s015_pins
&hsusbb1_pins
>;
@@ -409,3 +491,32 @@
&usbhsehci {
phys = <&hsusb1_phy>;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&dsi2 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 26/41] ARM: omap4-sdp.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP4 SDP board. The board has the following displays:
lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap4-sdp.dts | 107 +++++++++++++++++++++++++++++++++++++++-
1 file changed, 105 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index dbc81fb6ef03..cf9f6cbbd349 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -19,6 +19,12 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
+ aliases {
+ display0 = &lcd0;
+ display1 = &lcd1;
+ display2 = &hdmi0;
+ };
+
vdd_eth: fixedregulator-vdd-eth {
compatible = "regulator-fixed";
regulator-name = "VDD_ETH";
@@ -153,6 +159,47 @@
startup-delay-us = <70000>;
enable-active-high;
};
+
+ tpd12s015: encoder@0 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@0 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
};
&omap4_pmx_core {
@@ -163,8 +210,6 @@
&dmic_pins
&mcbsp1_pins
&mcbsp2_pins
- &dss_hdmi_pins
- &tpd12s015_pins
>;
uart2_pins: pinmux_uart2_pins {
@@ -550,3 +595,61 @@
mode = <3>;
power = <50>;
};
+
+&dss {
+ status = "ok";
+};
+
+&dsi1 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+
+ dsi1_out_ep: endpoint {
+ remote-endpoint = <&lcd0_in>;
+ lanes = <0 1 2 3 4 5>;
+ };
+
+ lcd0: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd0";
+
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102, reset */
+
+ lcd0_in: endpoint {
+ remote-endpoint = <&dsi1_out_ep>;
+ };
+ };
+};
+
+&dsi2 {
+ status = "ok";
+ vdd-supply = <&vcxio>;
+
+ dsi2_out_ep: endpoint {
+ remote-endpoint = <&lcd1_in>;
+ lanes = <0 1 2 3 4 5>;
+ };
+
+ lcd1: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd1";
+
+ gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104, reset */
+
+ lcd1_in: endpoint {
+ remote-endpoint = <&dsi2_out_ep>;
+ };
+ };
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 27/41] ARM: omap3-beagle.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 Beagle board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-beagle.dts | 116 +++++++++++++++++++++++++++++++++++++
1 file changed, 116 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 3ba4a625ea5b..2b8efe355734 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -24,6 +24,11 @@
reg = <0x80000000 0x10000000>; /* 256 MB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &tv0;
+ };
+
leds {
compatible = "gpio-leds";
pmu_stat {
@@ -80,6 +85,55 @@
};
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* 170, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tv0: connector@1 {
+ compatible = "svideo-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_wkup {
@@ -119,6 +173,45 @@
0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */
>;
};
+
+ tfp410_pins: pinmux_tfp410_pins {
+ pinctrl-single,pins = <
+ 0x194 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */
+ >;
+ };
+
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ 0x0ac (PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
+ 0x0ae (PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
+ 0x0b0 (PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
+ 0x0b2 (PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
+ 0x0b4 (PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
+ 0x0b6 (PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
+ 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ 0x0d0 (PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
+ 0x0d2 (PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
+ 0x0d4 (PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
+ 0x0d6 (PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
+ 0x0d8 (PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
+ 0x0da (PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
+ >;
+ };
};
&i2c1 {
@@ -199,3 +292,26 @@
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <2>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 28/41] ARM: omap3-beagle-xm.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 Beagle-xM board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-beagle-xm.dts | 119 ++++++++++++++++++++++++++++++++++
1 file changed, 119 insertions(+)
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index df33a50bc070..f6cec7e6ac11 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -24,6 +24,11 @@
reg = <0x80000000 0x20000000>; /* 512 MB */
};
+ aliases {
+ display0 = &dvi0;
+ display1 = &tv0;
+ };
+
leds {
compatible = "gpio-leds";
@@ -86,6 +91,54 @@
reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
vcc-supply = <&hsusb2_power>;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+
+ /* XXX pinctrl from twl */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tv0: connector@1 {
+ compatible = "svideo-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_wkup {
@@ -94,6 +147,17 @@
0x0e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE4) /* sys_boot2.gpio_4 */
>;
};
+
+ dss_dpi_pins2: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a (PIN_OUTPUT | MUX_MODE3) /* sys_boot0.dss_data18 */
+ 0x0c (PIN_OUTPUT | MUX_MODE3) /* sys_boot1.dss_data19 */
+ 0x10 (PIN_OUTPUT | MUX_MODE3) /* sys_boot3.dss_data20 */
+ 0x12 (PIN_OUTPUT | MUX_MODE3) /* sys_boot4.dss_data21 */
+ 0x14 (PIN_OUTPUT | MUX_MODE3) /* sys_boot5.dss_data22 */
+ 0x16 (PIN_OUTPUT | MUX_MODE3) /* sys_boot6.dss_data23 */
+ >;
+ };
};
&omap3_pmx_core {
@@ -125,6 +189,35 @@
0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
>;
};
+
+ dss_dpi_pins1: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ 0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ 0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ 0x0a8 (PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ 0x0aa (PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+
+ 0x0b8 (PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ 0x0ba (PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ 0x0bc (PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ 0x0be (PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ 0x0c0 (PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ 0x0c8 (PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ 0x0ca (PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ 0x0cc (PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ 0x0ce (PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+
+ 0x0d0 (PIN_OUTPUT | MUX_MODE3) /* dss_data18.dss_data0 */
+ 0x0d2 (PIN_OUTPUT | MUX_MODE3) /* dss_data19.dss_data1 */
+ 0x0d4 (PIN_OUTPUT | MUX_MODE3) /* dss_data20.dss_data2 */
+ 0x0d6 (PIN_OUTPUT | MUX_MODE3) /* dss_data21.dss_data3 */
+ 0x0d8 (PIN_OUTPUT | MUX_MODE3) /* dss_data22.dss_data4 */
+ 0x0da (PIN_OUTPUT | MUX_MODE3) /* dss_data23.dss_data5 */
+ >;
+ };
};
&i2c1 {
@@ -222,3 +315,29 @@
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &dss_dpi_pins1
+ &dss_dpi_pins2
+ >;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <2>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 29/41] ARM: omap3-igep0020.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
From: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Add DT data for OMAP3 IGEPv2 board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-igep0020.dts | 59 +++++++++++++++++++++++++++++++-----
1 file changed, 52 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts
index 1c7e74d2d2bc..bd8dcc9f7ab4 100644
--- a/arch/arm/boot/dts/omap3-igep0020.dts
+++ b/arch/arm/boot/dts/omap3-igep0020.dts
@@ -61,14 +61,52 @@
reset-gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; /* gpio_24 */
vcc-supply = <&hsusb1_power>;
};
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio6 10 GPIO_ACTIVE_LOW>; /* 170, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
};
&omap3_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <
&hsusbb1_pins
- &tfp410_pins
- &dss_pins
>;
hsusbb1_pins: pinmux_hsusbb1_pins {
@@ -88,13 +126,13 @@
>;
};
- tfp410_pins: tfp410_dvi_pins {
+ tfp410_pins: pinmux_tfp410_pins {
pinctrl-single,pins = <
0x196 (PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */
>;
};
- dss_pins: pinmux_dss_dvi_pins {
+ dss_dpi_pins: pinmux_dss_dpi_pins {
pinctrl-single,pins = <
0x0a4 (PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
0x0a6 (PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
@@ -216,7 +254,14 @@
phys = <&hsusb1_phy>;
};
-&vpll2 {
- /* Needed for DSS */
- regulator-name = "vdds_dsi";
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 30/41] ARM: omap3-n900.dts: add display information
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT data for OMAP3 N900 board. The board has the following displays:
lcd: LCD panel connected to OMAP's SDI output
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/boot/dts/omap3-n900.dts | 70 +++++++++++++++++++++++++++++++++++++---
1 file changed, 66 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 6fc85f963530..c1bb04d55d4b 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -74,6 +74,14 @@
};
};
+ tv: connector {
+ compatible = "composite-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
};
&omap3_pmx_core {
@@ -140,11 +148,23 @@
>;
};
- display_pins: pinmux_display_pins {
+ acx565akm_pins: pinmux_acx565akm_pins {
pinctrl-single,pins = <
0x0d4 (PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
>;
};
+
+ dss_sdi_pins: pinmux_dss_sdi_pins {
+ pinctrl-single,pins = <
+ 0x0c0 (PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
+ 0x0c2 (PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
+ 0x0c4 (PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
+ 0x0c6 (PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
+
+ 0x0d8 (PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
+ 0x0da (PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
+ >;
+ };
};
&i2c1 {
@@ -471,13 +491,21 @@
spi-max-frequency = <6000000>;
reg = <0>;
};
- mipid@2 {
- compatible = "acx565akm";
+
+ acx565akm@2 {
+ compatible = "sony,acx565akm";
spi-max-frequency = <6000000>;
reg = <2>;
pinctrl-names = "default";
- pinctrl-0 = <&display_pins>;
+ pinctrl-0 = <&acx565akm_pins>;
+
+ label = "lcd";
+ gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
+
+ lcd_in: endpoint {
+ remote-endpoint = <&sdi_out>;
+ };
};
};
@@ -503,3 +531,37 @@
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins>;
};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_sdi_pins>;
+
+ vdds_sdi-supply = <&vaux1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ sdi_out: endpoint {
+ remote-endpoint = <&lcd_in>;
+ datapairs = <2>;
+ };
+ };
+ };
+};
+
+&venc {
+ status = "ok";
+
+ vdda-supply = <&vdac>;
+
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <1>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 31/41] OMAPDSS: remove DT hacks for regulators
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
For booting Panda and 4430SDP with DT, while DSS did not support DT, we
had to had small hacks in the omapdss driver to get the regulators. With
DT now supported in DSS, we can remove those hacks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
drivers/video/omap2/dss/dsi.c | 9 +--------
drivers/video/omap2/dss/hdmi4.c | 9 +--------
2 files changed, 2 insertions(+), 16 deletions(-)
diff --git a/drivers/video/omap2/dss/dsi.c b/drivers/video/omap2/dss/dsi.c
index 98bb2d68a462..f461fe015554 100644
--- a/drivers/video/omap2/dss/dsi.c
+++ b/drivers/video/omap2/dss/dsi.c
@@ -1162,16 +1162,9 @@ static int dsi_regulator_init(struct platform_device *dsidev)
vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "vdd");
- if (IS_ERR(vdds_dsi))
- vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "vdds_dsi");
-
- /* DT HACK: try VCXIO to make omapdss work for o4 sdp/panda */
- if (IS_ERR(vdds_dsi))
- vdds_dsi = devm_regulator_get(&dsi->pdev->dev, "VCXIO");
-
if (IS_ERR(vdds_dsi)) {
if (PTR_ERR(vdds_dsi) != -EPROBE_DEFER)
- DSSERR("can't get VDDS_DSI regulator\n");
+ DSSERR("can't get DSI VDD regulator\n");
return PTR_ERR(vdds_dsi);
}
diff --git a/drivers/video/omap2/dss/hdmi4.c b/drivers/video/omap2/dss/hdmi4.c
index 064bec4e08d4..17b24b26f6cd 100644
--- a/drivers/video/omap2/dss/hdmi4.c
+++ b/drivers/video/omap2/dss/hdmi4.c
@@ -90,16 +90,9 @@ static int hdmi_init_regulator(void)
reg = devm_regulator_get(&hdmi.pdev->dev, "vdda");
- if (IS_ERR(reg)
- reg = devm_regulator_get(&hdmi.pdev->dev, "vdda_hdmi_dac");
-
- /* DT HACK: try VDAC to make omapdss work for o4 sdp/panda */
- if (IS_ERR(reg))
- reg = devm_regulator_get(&hdmi.pdev->dev, "VDAC");
-
if (IS_ERR(reg)) {
if (PTR_ERR(reg) != -EPROBE_DEFER)
- DSSERR("can't get VDDA_HDMI_DAC regulator\n");
+ DSSERR("can't get VDDA regulator\n");
return PTR_ERR(reg);
}
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 32/41] ARM: OMAP2+: remove pdata quirks for displays
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Remove pdata quirks for the displays on boards that are now supported
properly with DT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
arch/arm/mach-omap2/dss-common.c | 224 -------------------------------------
arch/arm/mach-omap2/pdata-quirks.c | 3 -
2 files changed, 227 deletions(-)
diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c
index dadccc91488c..010bb72d2b75 100644
--- a/arch/arm/mach-omap2/dss-common.c
+++ b/arch/arm/mach-omap2/dss-common.c
@@ -33,227 +33,3 @@
#include "soc.h"
#include "dss-common.h"
#include "mux.h"
-
-#define HDMI_GPIO_CT_CP_HPD 60 /* HPD mode enable/disable */
-#define HDMI_GPIO_LS_OE 41 /* Level shifter for HDMI */
-#define HDMI_GPIO_HPD 63 /* Hotplug detect */
-
-#define PANDA_DVI_TFP410_POWER_DOWN_GPIO 0
-
-/* DVI Connector */
-static struct connector_dvi_platform_data omap4_panda_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 2,
-};
-
-static struct platform_device omap4_panda_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap4_panda_dvi_connector_pdata,
-};
-
-/* TFP410 DPI-to-DVI chip */
-static struct encoder_tfp410_platform_data omap4_panda_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = PANDA_DVI_TFP410_POWER_DOWN_GPIO,
-};
-
-static struct platform_device omap4_panda_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap4_panda_tfp410_pdata,
-};
-
-/* HDMI Connector */
-static struct connector_hdmi_platform_data omap4_panda_hdmi_connector_pdata = {
- .name = "hdmi",
- .source = "tpd12s015.0",
-};
-
-static struct platform_device omap4_panda_hdmi_connector_device = {
- .name = "connector-hdmi",
- .id = 0,
- .dev.platform_data = &omap4_panda_hdmi_connector_pdata,
-};
-
-/* TPD12S015 HDMI ESD protection & level shifter chip */
-static struct encoder_tpd12s015_platform_data omap4_panda_tpd_pdata = {
- .name = "tpd12s015.0",
- .source = "hdmi.0",
-
- .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
- .ls_oe_gpio = HDMI_GPIO_LS_OE,
- .hpd_gpio = HDMI_GPIO_HPD,
-};
-
-static struct platform_device omap4_panda_tpd_device = {
- .name = "tpd12s015",
- .id = 0,
- .dev.platform_data = &omap4_panda_tpd_pdata,
-};
-
-static struct omap_dss_board_info omap4_panda_dss_data = {
- .default_display_name = "dvi",
-};
-
-void __init omap4_panda_display_init_of(void)
-{
- omap_display_init(&omap4_panda_dss_data);
-
- platform_device_register(&omap4_panda_tfp410_device);
- platform_device_register(&omap4_panda_dvi_connector_device);
-
- platform_device_register(&omap4_panda_tpd_device);
- platform_device_register(&omap4_panda_hdmi_connector_device);
-}
-
-
-/* OMAP4 Blaze display data */
-
-#define DISPLAY_SEL_GPIO 59 /* LCD2/PicoDLP switch */
-#define DLP_POWER_ON_GPIO 40
-
-static struct panel_dsicm_platform_data dsi1_panel = {
- .name = "lcd",
- .source = "dsi.0",
- .reset_gpio = 102,
- .use_ext_te = false,
- .ext_te_gpio = 101,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct platform_device sdp4430_lcd_device = {
- .name = "panel-dsi-cm",
- .id = 0,
- .dev.platform_data = &dsi1_panel,
-};
-
-static struct panel_dsicm_platform_data dsi2_panel = {
- .name = "lcd2",
- .source = "dsi.1",
- .reset_gpio = 104,
- .use_ext_te = false,
- .ext_te_gpio = 103,
- .pin_config = {
- .num_pins = 6,
- .pins = { 0, 1, 2, 3, 4, 5 },
- },
-};
-
-static struct platform_device sdp4430_lcd2_device = {
- .name = "panel-dsi-cm",
- .id = 1,
- .dev.platform_data = &dsi2_panel,
-};
-
-/* HDMI Connector */
-static struct connector_hdmi_platform_data sdp4430_hdmi_connector_pdata = {
- .name = "hdmi",
- .source = "tpd12s015.0",
-};
-
-static struct platform_device sdp4430_hdmi_connector_device = {
- .name = "connector-hdmi",
- .id = 0,
- .dev.platform_data = &sdp4430_hdmi_connector_pdata,
-};
-
-/* TPD12S015 HDMI ESD protection & level shifter chip */
-static struct encoder_tpd12s015_platform_data sdp4430_tpd_pdata = {
- .name = "tpd12s015.0",
- .source = "hdmi.0",
-
- .ct_cp_hpd_gpio = HDMI_GPIO_CT_CP_HPD,
- .ls_oe_gpio = HDMI_GPIO_LS_OE,
- .hpd_gpio = HDMI_GPIO_HPD,
-};
-
-static struct platform_device sdp4430_tpd_device = {
- .name = "tpd12s015",
- .id = 0,
- .dev.platform_data = &sdp4430_tpd_pdata,
-};
-
-
-static struct omap_dss_board_info sdp4430_dss_data = {
- .default_display_name = "lcd",
-};
-
-/*
- * we select LCD2 by default (instead of Pico DLP) by setting DISPLAY_SEL_GPIO.
- * Setting DLP_POWER_ON gpio enables the VDLP_2V5 VDLP_1V8 and VDLP_1V0 rails
- * used by picodlp on the 4430sdp platform. Keep this gpio disabled as LCD2 is
- * selected by default
- */
-void __init omap_4430sdp_display_init_of(void)
-{
- int r;
-
- r = gpio_request_one(DISPLAY_SEL_GPIO, GPIOF_OUT_INIT_HIGH,
- "display_sel");
- if (r)
- pr_err("%s: Could not get display_sel GPIO\n", __func__);
-
- r = gpio_request_one(DLP_POWER_ON_GPIO, GPIOF_OUT_INIT_LOW,
- "DLP POWER ON");
- if (r)
- pr_err("%s: Could not get DLP POWER ON GPIO\n", __func__);
-
- omap_display_init(&sdp4430_dss_data);
-
- platform_device_register(&sdp4430_lcd_device);
- platform_device_register(&sdp4430_lcd2_device);
-
- platform_device_register(&sdp4430_tpd_device);
- platform_device_register(&sdp4430_hdmi_connector_device);
-}
-
-
-/* OMAP3 IGEPv2 data */
-
-#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO 170
-
-/* DVI Connector */
-static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = {
- .name = "dvi",
- .source = "tfp410.0",
- .i2c_bus_num = 2,
-};
-
-static struct platform_device omap3_igep2_dvi_connector_device = {
- .name = "connector-dvi",
- .id = 0,
- .dev.platform_data = &omap3_igep2_dvi_connector_pdata,
-};
-
-/* TFP410 DPI-to-DVI chip */
-static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = {
- .name = "tfp410.0",
- .source = "dpi.0",
- .data_lines = 24,
- .power_down_gpio = IGEP2_DVI_TFP410_POWER_DOWN_GPIO,
-};
-
-static struct platform_device omap3_igep2_tfp410_device = {
- .name = "tfp410",
- .id = 0,
- .dev.platform_data = &omap3_igep2_tfp410_pdata,
-};
-
-static struct omap_dss_board_info igep2_dss_data = {
- .default_display_name = "dvi",
-};
-
-void __init omap3_igep2_display_init_of(void)
-{
- omap_display_init(&igep2_dss_data);
-
- platform_device_register(&omap3_igep2_tfp410_device);
- platform_device_register(&omap3_igep2_dvi_connector_device);
-}
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index 39f020c982e8..68e3bca42e60 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -80,7 +80,6 @@ static void __init hsmmc2_internal_input_clk(void)
static void __init omap3_igep0020_legacy_init(void)
{
- omap3_igep2_display_init_of();
}
static void __init omap3_evm_legacy_init(void)
@@ -97,14 +96,12 @@ static void __init omap3_zoom_legacy_init(void)
#ifdef CONFIG_ARCH_OMAP4
static void __init omap4_sdp_legacy_init(void)
{
- omap_4430sdp_display_init_of();
legacy_init_wl12xx(WL12XX_REFCLOCK_26,
WL12XX_TCXOCLOCK_26, 53);
}
static void __init omap4_panda_legacy_init(void)
{
- omap4_panda_display_init_of();
legacy_init_ehci_clk("auxclk3_ck");
legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
}
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 33/41] Doc/DT: Add OMAP DSS DT Bindings
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add device tree bindings for OMAP Display Subsystem for the following
SoCs: OMAP2, OMAP3, OMAP4.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/ti,omap-dss.txt | 197 +++++++++++++++++++++
.../devicetree/bindings/video/ti,omap2-dss.txt | 54 ++++++
.../devicetree/bindings/video/ti,omap3-dss.txt | 73 ++++++++
.../devicetree/bindings/video/ti,omap4-dss.txt | 99 +++++++++++
.../devicetree/bindings/video/video-ports.txt | 22 +++
5 files changed, 445 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/ti,omap-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap2-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap3-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/ti,omap4-dss.txt
create mode 100644 Documentation/devicetree/bindings/video/video-ports.txt
diff --git a/Documentation/devicetree/bindings/video/ti,omap-dss.txt b/Documentation/devicetree/bindings/video/ti,omap-dss.txt
new file mode 100644
index 000000000000..3b3a7c09106c
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap-dss.txt
@@ -0,0 +1,197 @@
+Texas Instruments OMAP Display Subsystem
+====================
+
+Generic Description
+-------------------
+
+This document is a generic description of the OMAP Display Subsystem bindings.
+Binding details for each OMAP SoC version are described in respective binding
+documentation.
+
+The OMAP Display Subsystem (DSS) hardware consists of DSS Core, DISPC module and
+a number of encoder modules. All DSS versions contain DSS Core and DISPC, but
+the encoder modules vary.
+
+The DSS Core is the parent of the other DSS modules, and manages clock routing,
+integration to the SoC, etc.
+
+DISPC is the display controller, which reads pixels from the memory and outputs
+a RGB pixel stream to encoders.
+
+The encoder modules encode the received RGB pixel stream to a video output like
+HDMI, MIPI DPI, etc.
+
+Video Ports
+-----------
+
+The DSS Core and the encoders have video port outputs. The structure of the
+video ports is described in Documentation/devicetree/bindings/video/video-
+ports.txt, and the properties for the ports and endpoints for each encoder are
+described in the SoC's DSS binding documentation.
+
+The video ports are used to describe the connections to external hardware, like
+panels or external encoders.
+
+Aliases
+-------
+
+The board dts file may define aliases for displays to assign "displayX" style
+name for each display. If no aliases are defined, a semi-random number is used
+for the display.
+
+Example
+-------
+
+A shortened example of the DSS description for OMAP4, with non-relevant parts
+removed, defined in omap4.dtsi:
+
+dss: dss@58000000 {
+ compatible = "ti,omap4-dss", "simple-bus";
+ reg = <0x58000000 0x80>;
+ status = "disabled";
+ ti,hwmods = "dss_core";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dispc@58001000 {
+ compatible = "ti,omap4-dispc";
+ reg = <0x58001000 0x1000>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "dss_dispc";
+ };
+
+ hdmi: encoder@58006000 {
+ compatible = "ti,omap4-hdmi";
+ reg = <0x58006000 0x200>,
+ <0x58006200 0x100>,
+ <0x58006300 0x100>,
+ <0x58006400 0x1000>;
+ reg-names = "wp", "pll", "phy", "core";
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ ti,hwmods = "dss_hdmi";
+ };
+};
+
+A shortened example of the board description for OMAP4 Panda board, defined in
+omap4-panda.dts.
+
+The Panda board has a DVI and a HDMI connector, and the board contains a TFP410
+chip (MIPI DPI to DVI encoder) and a TPD12S015 chip (HDMI ESD protection & level
+shifter). The video pipelines for the connectors are formed as follows:
+
+DSS Core --(MIPI DPI)--> TFP410 --(DVI)--> DVI Connector
+OMAP HDMI --(HDMI)--> TPD12S015 --(HDMI)--> HDMI COnnector
+
+/ {
+ aliases {
+ display0 = &dvi0;
+ display1 = &hdmi0;
+ };
+
+ tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; /* 0, power-down */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tfp410_pins>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+
+ tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&tpd12s015_pins>;
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
+
+ hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+ };
+};
+
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ dpi_out: endpoint {
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+};
+
+&hdmi {
+ status = "ok";
+ vdda-supply = <&vdac>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_hdmi_pins>;
+
+ hdmi_out: endpoint {
+ remote-endpoint = <&tpd12s015_in>;
+ };
+};
diff --git a/Documentation/devicetree/bindings/video/ti,omap2-dss.txt b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt
new file mode 100644
index 000000000000..fa8bb2ed1170
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap2-dss.txt
@@ -0,0 +1,54 @@
+Texas Instruments OMAP2 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap2-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Optional nodes:
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap2-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap2-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap2-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+VENC Endpoint required properties:
+
+Required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
diff --git a/Documentation/devicetree/bindings/video/ti,omap3-dss.txt b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt
new file mode 100644
index 000000000000..2b62c78c9596
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap3-dss.txt
@@ -0,0 +1,73 @@
+Texas Instruments OMAP3 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap3-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Optional nodes:
+- Video ports:
+ - Port 0: DPI output
+ - Port 1: SDI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+SDI Endpoint required properties:
+- datapairs: number of datapairs used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap3-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap3-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap3-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap3-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1"
+- vdd-supply: power supply for DSI
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
diff --git a/Documentation/devicetree/bindings/video/ti,omap4-dss.txt b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt
new file mode 100644
index 000000000000..37aa9e6a173e
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,omap4-dss.txt
@@ -0,0 +1,99 @@
+Texas Instruments OMAP4 Display Subsystem
+====================+
+See Documentation/devicetree/bindings/video/ti,omap-dss.txt for generic
+description about OMAP Display Subsystem bindings.
+
+DSS Core
+--------
+
+Required properties:
+- compatible: "ti,omap4-dss"
+- reg: address and length of the register space
+- ti,hwmods: "dss_core"
+
+Required nodes:
+- DISPC
+
+Optional nodes:
+- DSS Submodules: RFBI, VENC, DSI, HDMI
+- Video port for DPI output
+
+DPI Endpoint required properties:
+- data-lines: number of lines used
+
+
+DISPC
+-----
+
+Required properties:
+- compatible: "ti,omap4-dispc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_dispc"
+- interrupts: the DISPC interrupt
+
+
+RFBI
+----
+
+Required properties:
+- compatible: "ti,omap4-rfbi"
+- reg: address and length of the register space
+- ti,hwmods: "dss_rfbi"
+
+Optional nodes:
+- Video port for RFBI output
+- RFBI controlled peripherals
+
+
+VENC
+----
+
+Required properties:
+- compatible: "ti,omap4-venc"
+- reg: address and length of the register space
+- ti,hwmods: "dss_venc"
+- vdda-supply: power supply for DAC
+
+Optional nodes:
+- Video port for VENC output
+
+VENC Endpoint required properties:
+- ti,invert-polarity: invert the polarity of the video signal
+- ti,channels: 1 for composite, 2 for s-video
+
+
+DSI
+---
+
+Required properties:
+- compatible: "ti,omap4-dsi"
+- reg: addresses and lengths of the register spaces for 'proto', 'phy' and 'pll'
+- reg-names: "proto", "phy", "pll"
+- interrupts: the DSI interrupt line
+- ti,hwmods: "dss_dsi1" or "dss_dsi2"
+- vdd-supply: power supply for DSI
+
+Optional nodes:
+- Video port for DSI output
+- DSI controlled peripherals
+
+DSI Endpoint required properties:
+- lanes: list of pin numbers for the DSI lanes: CLK+, CLK-, DATA0+, DATA0-,
+ DATA1+, DATA1-, ...
+
+
+HDMI
+----
+
+Required properties:
+- compatible: "ti,omap4-hdmi"
+- reg: addresses and lengths of the register spaces for 'wp', 'pll', 'phy',
+ 'core'
+- reg-names: "wp", "pll", "phy", "core"
+- interrupts: the HDMI interrupt line
+- ti,hwmods: "dss_hdmi"
+- vdda-supply: vdda power supply
+
+Optional nodes:
+- Video port for HDMI output
diff --git a/Documentation/devicetree/bindings/video/video-ports.txt b/Documentation/devicetree/bindings/video/video-ports.txt
new file mode 100644
index 000000000000..dad4c436caae
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/video-ports.txt
@@ -0,0 +1,22 @@
+Video Ports
+=====+
+The video port bindings used for display devices is a superset of the v4l2 video
+ports described here:
+
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+The only difference is a more compact way to describe devices with only one
+endpoint. In cases like that, the 'ports' and 'port' nodes are not needed. For
+example, a DPI panel with a single input endpoint:
+
+lcd0: display@0 {
+ compatible = "samsung,lte430wq-f0c", "panel-dpi";
+
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+};
+
+The rest of the bindings are the same as in v4l2 video port bindings and not
+described here.
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 34/41] Doc/DT: Add DT binding documentation for Analog TV Connector
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for Analog TV Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../bindings/video/analog-tv-connector.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/analog-tv-connector.txt
diff --git a/Documentation/devicetree/bindings/video/analog-tv-connector.txt b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
new file mode 100644
index 000000000000..d6be373d8705
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/analog-tv-connector.txt
@@ -0,0 +1,23 @@
+Analog TV Connector
+=========+
+Required properties:
+- compatible: "composite-connector" or "svideo-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+
+Required nodes:
+- Video port for TV input
+
+Example
+-------
+
+tv: connector {
+ compatible = "composite-connector";
+ label = "tv";
+
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 35/41] Doc/DT: Add DT binding documentation for DVI Connector
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for DVI Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/dvi-connector.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/dvi-connector.txt
diff --git a/Documentation/devicetree/bindings/video/dvi-connector.txt b/Documentation/devicetree/bindings/video/dvi-connector.txt
new file mode 100644
index 000000000000..6a0aff866c78
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/dvi-connector.txt
@@ -0,0 +1,26 @@
+DVI Connector
+=======
+
+Required properties:
+- compatible: "dvi-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+- i2c-bus: phandle to the i2c bus that is connected to DVI DDC
+
+Required nodes:
+- Video port for DVI input
+
+Example
+-------
+
+dvi0: connector@0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ i2c-bus = <&i2c3>;
+
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 36/41] Doc/DT: Add DT binding documentation for HDMI Connector
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for HDMI Connector.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/hdmi-connector.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/hdmi-connector.txt
diff --git a/Documentation/devicetree/bindings/video/hdmi-connector.txt b/Documentation/devicetree/bindings/video/hdmi-connector.txt
new file mode 100644
index 000000000000..5d25f6a432bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/hdmi-connector.txt
@@ -0,0 +1,23 @@
+HDMI Connector
+=======
+
+Required properties:
+- compatible: "hdmi-connector"
+
+Optional properties:
+- label: a symbolic name for the connector
+
+Required nodes:
+- Video port for HDMI input
+
+Example
+-------
+
+hdmi0: connector@1 {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&tpd12s015_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 37/41] Doc/DT: Add DT binding documentation for MIPI DPI Panel
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for MIPI DPI Panel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/panel-dpi.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/panel-dpi.txt
diff --git a/Documentation/devicetree/bindings/video/panel-dpi.txt b/Documentation/devicetree/bindings/video/panel-dpi.txt
new file mode 100644
index 000000000000..72636c6f1c67
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/panel-dpi.txt
@@ -0,0 +1,43 @@
+Generic MIPI DPI Panel
+===========
+
+Required properties:
+- compatible: "panel-dpi"
+
+Optional properties:
+- label: a symbolic name for the panel
+- gpios: panel enable gpio and backlight enable gpio
+
+Required nodes:
+- "panel-timing" containing video timings
+ (Documentation/devicetree/bindings/video/display-timing.txt)
+- Video port for DPI input
+
+Example
+-------
+
+lcd0: display@0 {
+ compatible = "samsung,lte430wq-f0c", "panel-dpi";
+ label = "lcd";
+
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_out>;
+ };
+
+ panel-timing {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <1>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 38/41] Doc/DT: Add DT binding documentation for MIPI DSI CM Panel
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for MIPI DSI Command Mode Panel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/panel-dsi-cm.txt | 26 ++++++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/panel-dsi-cm.txt
diff --git a/Documentation/devicetree/bindings/video/panel-dsi-cm.txt b/Documentation/devicetree/bindings/video/panel-dsi-cm.txt
new file mode 100644
index 000000000000..73f422556d4f
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/panel-dsi-cm.txt
@@ -0,0 +1,26 @@
+Generic MIPI DSI Command Mode Panel
+=================+
+Required properties:
+- compatible: "panel-dsi-cm"
+
+Optional properties:
+- label: a symbolic name for the panel
+- gpios: panel reset gpio and TE gpio
+
+Required nodes:
+- Video port for DSI input
+
+Example
+-------
+
+lcd0: display {
+ compatible = "tpo,taal", "panel-dsi-cm";
+ label = "lcd0";
+
+ gpios = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102, reset */
+
+ lcd0_in: endpoint {
+ remote-endpoint = <&dsi1_out_ep>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 39/41] Doc/DT: Add DT binding documentation for Sony acx565akm panel
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for Sony acx565akm panel
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/sony,acx565akm.txt | 28 ++++++++++++++++++++++
1 file changed, 28 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/sony,acx565akm.txt
diff --git a/Documentation/devicetree/bindings/video/sony,acx565akm.txt b/Documentation/devicetree/bindings/video/sony,acx565akm.txt
new file mode 100644
index 000000000000..cd9cfdf7e3fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/sony,acx565akm.txt
@@ -0,0 +1,28 @@
+Sony ACX565AKM SDI Panel
+============
+
+Required properties:
+- compatible: "sony,acx565akm"
+
+Optional properties:
+- label: a symbolic name for the panel
+- gpios: panel reset gpio
+
+Required nodes:
+- Video port for SDI input
+
+Example
+-------
+
+acx565akm@2 {
+ compatible = "sony,acx565akm";
+ spi-max-frequency = <6000000>;
+ reg = <2>;
+
+ label = "lcd";
+ gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
+
+ lcd_in: endpoint {
+ remote-endpoint = <&sdi_out>;
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 40/41] Doc/DT: Add DT binding documentation for TFP410 encoder
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for TFP410 encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/ti,tfp410.txt | 41 ++++++++++++++++++++++
1 file changed, 41 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/ti,tfp410.txt
diff --git a/Documentation/devicetree/bindings/video/ti,tfp410.txt b/Documentation/devicetree/bindings/video/ti,tfp410.txt
new file mode 100644
index 000000000000..6a5a04627584
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,tfp410.txt
@@ -0,0 +1,41 @@
+TFP410 DPI to DVI encoder
+============+
+Required properties:
+- compatible: "ti,tfp410"
+
+Optional properties:
+- gpios: power-down gpio
+
+Required nodes:
+- Video port 0 for DPI input
+- Video port 1 for DVI output
+
+Example
+-------
+
+tfp410: encoder@0 {
+ compatible = "ti,tfp410";
+ gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint@0 {
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint@0 {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCHv3 41/41] Doc/DT: Add DT binding documentation for tpd12s015 encoder
From: Tomi Valkeinen @ 2014-01-21 10:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-1-git-send-email-tomi.valkeinen@ti.com>
Add DT binding documentation for tpd12s015 encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
---
.../devicetree/bindings/video/ti,tpd12s015.txt | 44 ++++++++++++++++++++++
1 file changed, 44 insertions(+)
create mode 100644 Documentation/devicetree/bindings/video/ti,tpd12s015.txt
diff --git a/Documentation/devicetree/bindings/video/ti,tpd12s015.txt b/Documentation/devicetree/bindings/video/ti,tpd12s015.txt
new file mode 100644
index 000000000000..26e6d32e3f20
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/ti,tpd12s015.txt
@@ -0,0 +1,44 @@
+TPD12S015 HDMI level shifter and ESD protection chip
+==========================
+
+Required properties:
+- compatible: "ti,tpd12s015"
+
+Optional properties:
+- gpios: CT CP HPD, LS OE and HPD gpios
+
+Required nodes:
+- Video port 0 for HDMI input
+- Video port 1 for HDMI output
+
+Example
+-------
+
+tpd12s015: encoder@1 {
+ compatible = "ti,tpd12s015";
+
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
+ <&gpio2 9 GPIO_ACTIVE_HIGH>, /* 41, LS OE */
+ <&gpio2 31 GPIO_ACTIVE_HIGH>; /* 63, HPD */
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tpd12s015_in: endpoint@0 {
+ remote-endpoint = <&hdmi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tpd12s015_out: endpoint@0 {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+};
--
1.8.3.2
^ permalink raw reply related
* [PATCH 0/2] fbdev: shmobile-lcdcfb: Fix sparse warnings
From: Laurent Pinchart @ 2014-01-21 11:59 UTC (permalink / raw)
To: linux-fbdev
Hello,
The subject says it all, these two patches fix sparse warnings.
Laurent Pinchart (2):
fbdev: shmobile-lcdcfb: Use NULL instead of 0 as NULL pointer
fbdev: shmobile-lcdcfb: Fix sparse address space cast warning
drivers/video/sh_mobile_lcdcfb.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--
Regards,
Laurent Pinchart
^ permalink raw reply
* [PATCH 1/2] fbdev: shmobile-lcdcfb: Use NULL instead of 0 as NULL pointer
From: Laurent Pinchart @ 2014-01-21 11:59 UTC (permalink / raw)
To: linux-fbdev
Setting a pointer to NULL shouldn't use 0.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
drivers/video/sh_mobile_lcdcfb.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c
index ab85ad6..2bcc84a 100644
--- a/drivers/video/sh_mobile_lcdcfb.c
+++ b/drivers/video/sh_mobile_lcdcfb.c
@@ -1227,7 +1227,7 @@ static void sh_mobile_lcdc_stop(struct sh_mobile_lcdc_priv *priv)
/* Free the MERAM cache. */
if (ch->cache) {
sh_mobile_meram_cache_free(priv->meram_dev, ch->cache);
- ch->cache = 0;
+ ch->cache = NULL;
}
}
--
1.8.3.2
^ permalink raw reply related
* [PATCH 2/2] fbdev: shmobile-lcdcfb: Fix sparse address space cast warning
From: Laurent Pinchart @ 2014-01-21 11:59 UTC (permalink / raw)
To: linux-fbdev
The fbdev screen_base field stores the frame buffer base address.
Depending on the drivers this is either an I/O memory pointer or a
kernel virtual pointer.
The field is marked with the __iomem address space type, cast the kernel
pointer to __iomem to make sparse happy.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
---
drivers/video/sh_mobile_lcdcfb.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/video/sh_mobile_lcdcfb.c b/drivers/video/sh_mobile_lcdcfb.c
index 2bcc84a..5805044 100644
--- a/drivers/video/sh_mobile_lcdcfb.c
+++ b/drivers/video/sh_mobile_lcdcfb.c
@@ -1710,7 +1710,7 @@ sh_mobile_lcdc_overlay_fb_init(struct sh_mobile_lcdc_overlay *ovl)
info->flags = FBINFO_FLAG_DEFAULT;
info->fbops = &sh_mobile_lcdc_overlay_ops;
info->device = priv->dev;
- info->screen_base = ovl->fb_mem;
+ info->screen_base = (char __force __iomem *)ovl->fb_mem;
info->par = ovl;
/* Initialize fixed screen information. Restrict pan to 2 lines steps
@@ -2212,7 +2212,7 @@ sh_mobile_lcdc_channel_fb_init(struct sh_mobile_lcdc_chan *ch,
info->flags = FBINFO_FLAG_DEFAULT;
info->fbops = &sh_mobile_lcdc_ops;
info->device = priv->dev;
- info->screen_base = ch->fb_mem;
+ info->screen_base = (char __force __iomem *)ch->fb_mem;
info->pseudo_palette = &ch->pseudo_palette;
info->par = ch;
--
1.8.3.2
^ permalink raw reply related
* Re: [PATCHv3 30/41] ARM: omap3-n900.dts: add display information
From: Sebastian Reichel @ 2014-01-21 15:26 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-31-git-send-email-tomi.valkeinen@ti.com>
[-- Attachment #1: Type: text/plain, Size: 413 bytes --]
On Tue, Jan 21, 2014 at 12:57:02PM +0200, Tomi Valkeinen wrote:
> Add DT data for OMAP3 N900 board. The board has the following
> displays:
>
> lcd: LCD panel connected to OMAP's SDI output
> tv: analog svideo
>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Your dss-dt-review-3 branch boots on my N900 with working display.
Tested-by: Sebastian Reichel <sre@debian.org>
-- Sebastian
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply
* Re: [PATCHv3 39/41] Doc/DT: Add DT binding documentation for Sony acx565akm panel
From: Sebastian Reichel @ 2014-01-21 15:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1390301833-24944-40-git-send-email-tomi.valkeinen@ti.com>
[-- Attachment #1: Type: text/plain, Size: 250 bytes --]
On Tue, Jan 21, 2014 at 12:57:11PM +0200, Tomi Valkeinen wrote:
> Add DT binding documentation for Sony acx565akm panel
>
> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sebastian Reichel <sre@debian.org>
-- Sebastian
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 819 bytes --]
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox