[PATCH v4 0/3] arm64: Add LECARC ACPI IDs for DesignWare GPIO, SPI, I2C

[PATCH v4 0/3] arm64: Add LECARC ACPI IDs for DesignWare GPIO, SPI, I2C

[Thomas Lin]

This patch series adds ACPI identification for LECARC SoCs that
integrate Synopsys DesignWare peripherals.

LECARC platforms use the following ACPI HIDs:

GPIO: LECA0001 (V1 register offsets)

SPI: LECA0002 (requires custom init function)

I2C: LECA0003

The patches are independent but share a common dependency on the
ACPI description file (acpi_apd.c) for SPI and I2C. To avoid merge
conflicts, they are submitted as a single series with the following
order:

Patch 1: GPIO – add LECA0001 to dwapb_gpio ACPI match table.
Patch 2: SPI – add LECA0002 and dw_spi_lecarc_init() to spi-dw-mmio,
plus corresponding entry in acpi_apd.c.
Patch 3: I2C – add LECA0003 to DesignWare I2C ACPI match table,
plus corresponding entry in acpi_apd.c.

All changes have been tested on LECARC evaluation board with
kernel v7.0.0-rc7. No regressions observed on existing hardware.

Changes since v1:

- Revised subject lines to match subsystem style guidelines
- No functional changes
- All the comments from reviews has been fixed

Changes since v2:
- Wrap long commit description lines to 72 columns
- Fix code indentation in spi-dw-mmio.c: use tabs + spaces for alignment
- No functional changes

Changes since v3:
- Start a new thread for each revision

Thomas Lin (3):
  gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs
  spi: dw-mmio: Add ACPI ID LECA0002 for LECARC SoCs
  i2c: designware: Add ACPI ID LECA0003 for LECARC SoCs

 drivers/acpi/acpi_apd.c                     | 13 +++++++++++++
 drivers/gpio/gpio-dwapb.c                   |  1 +
 drivers/i2c/busses/i2c-designware-platdrv.c |  1 +
 drivers/spi/spi-dw-mmio.c                   |  7 ++++---
 4 files changed, 19 insertions(+), 3 deletions(-)

-- 
2.43.0

[PATCH v4 1/3] gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs

[Thomas Lin]

Add ACPI ID "LECA0001" for LECARC SoCs that use the DesignWare
GPIO controller with V1 register offsets.

Signed-off-by: Thomas Lin <thomas_lin@lecomputing.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <brgl@kernel.org>
---
 drivers/gpio/gpio-dwapb.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpio/gpio-dwapb.c b/drivers/gpio/gpio-dwapb.c
index 15cebc8b5d66..c1f3d83a67c1 100644
--- a/drivers/gpio/gpio-dwapb.c
+++ b/drivers/gpio/gpio-dwapb.c
@@ -694,6 +694,7 @@ static const struct acpi_device_id dwapb_acpi_match[] = {
 	{"APMC0D07", GPIO_REG_OFFSET_V1},
 	{"APMC0D81", GPIO_REG_OFFSET_V2},
 	{"FUJI200A", GPIO_REG_OFFSET_V1},
+	{"LECA0001", GPIO_REG_OFFSET_V1},
 	{ }
 };
 MODULE_DEVICE_TABLE(acpi, dwapb_acpi_match);
-- 
2.43.0

[PATCH v4 2/3] spi: dw-mmio: Add ACPI ID LECA0002 for LECARC SoCs

[Thomas Lin]

This ID requires a custom initialization function
dw_spi_hssi_no_dma_init() that sets dws->dws.ip to DW_HSSI_ID.

Signed-off-by: Thomas Lin <thomas_lin@lecomputing.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
---
 drivers/acpi/acpi_apd.c   | 7 +++++++
 drivers/spi/spi-dw-mmio.c | 7 ++++---
 2 files changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/acpi/acpi_apd.c b/drivers/acpi/acpi_apd.c
index bed0791c17fc..4d5a51d30adc 100644
--- a/drivers/acpi/acpi_apd.c
+++ b/drivers/acpi/acpi_apd.c
@@ -181,6 +181,12 @@ static const struct apd_device_desc hip08_spi_desc = {
 	.setup = acpi_apd_setup,
 	.fixed_clk_rate = 250000000,
 };
+
+static const struct apd_device_desc leca_spi_desc = {
+	.setup = acpi_apd_setup,
+	.fixed_clk_rate = 400000000,
+};
+
 #endif /* CONFIG_ARM64 */
 
 #endif
@@ -251,6 +257,7 @@ static const struct acpi_device_id acpi_apd_device_ids[] = {
 	{ "HISI02A2", APD_ADDR(hip08_i2c_desc) },
 	{ "HISI02A3", APD_ADDR(hip08_lite_i2c_desc) },
 	{ "HISI0173", APD_ADDR(hip08_spi_desc) },
+	{ "LECA0002", APD_ADDR(leca_spi_desc) },
 	{ "NXP0001", APD_ADDR(nxp_i2c_desc) },
 #endif
 	{ }
diff --git a/drivers/spi/spi-dw-mmio.c b/drivers/spi/spi-dw-mmio.c
index 1bfdf24c3227..4fc864d38cff 100644
--- a/drivers/spi/spi-dw-mmio.c
+++ b/drivers/spi/spi-dw-mmio.c
@@ -226,8 +226,8 @@ static int dw_spi_hssi_init(struct platform_device *pdev,
 	return 0;
 }
 
-static int dw_spi_intel_init(struct platform_device *pdev,
-			     struct dw_spi_mmio *dwsmmio)
+static int dw_spi_hssi_no_dma_init(struct platform_device *pdev,
+				   struct dw_spi_mmio *dwsmmio)
 {
 	dwsmmio->dws.ip = DW_HSSI_ID;
 
@@ -438,7 +438,7 @@ static const struct of_device_id dw_spi_mmio_of_match[] = {
 	{ .compatible = "amazon,alpine-dw-apb-ssi", .data = dw_spi_alpine_init},
 	{ .compatible = "renesas,rzn1-spi", .data = dw_spi_pssi_init},
 	{ .compatible = "snps,dwc-ssi-1.01a", .data = dw_spi_hssi_init},
-	{ .compatible = "intel,keembay-ssi", .data = dw_spi_intel_init},
+	{ .compatible = "intel,keembay-ssi", .data = dw_spi_hssi_no_dma_init},
 	{
 		.compatible = "intel,mountevans-imc-ssi",
 		.data = dw_spi_mountevans_imc_init,
@@ -453,6 +453,7 @@ MODULE_DEVICE_TABLE(of, dw_spi_mmio_of_match);
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id dw_spi_mmio_acpi_match[] = {
 	{"HISI0173", (kernel_ulong_t)dw_spi_pssi_init},
+	{"LECA0002", (kernel_ulong_t)dw_spi_hssi_no_dma_init},
 	{},
 };
 MODULE_DEVICE_TABLE(acpi, dw_spi_mmio_acpi_match);
-- 
2.43.0

[PATCH v4 3/3] i2c: designware: Add ACPI ID LECA0003 for LECARC SoCs

[Thomas Lin]

Add ACPI ID "LECA0003" for LECARC SoCs that integrate
the DesignWare I2C controller.
Also add corresponding ACPI description in acpi_apd.c.

Signed-off-by: Thomas Lin <thomas_lin@lecomputing.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
---
 drivers/acpi/acpi_apd.c                     | 6 ++++++
 drivers/i2c/busses/i2c-designware-platdrv.c | 1 +
 2 files changed, 7 insertions(+)

diff --git a/drivers/acpi/acpi_apd.c b/drivers/acpi/acpi_apd.c
index 4d5a51d30adc..008bd0552cb7 100644
--- a/drivers/acpi/acpi_apd.c
+++ b/drivers/acpi/acpi_apd.c
@@ -187,6 +187,11 @@ static const struct apd_device_desc leca_spi_desc = {
 	.fixed_clk_rate = 400000000,
 };
 
+static const struct apd_device_desc leca_i2c_desc = {
+	.setup = acpi_apd_setup,
+	.fixed_clk_rate = 250000000,
+};
+
 #endif /* CONFIG_ARM64 */
 
 #endif
@@ -258,6 +263,7 @@ static const struct acpi_device_id acpi_apd_device_ids[] = {
 	{ "HISI02A3", APD_ADDR(hip08_lite_i2c_desc) },
 	{ "HISI0173", APD_ADDR(hip08_spi_desc) },
 	{ "LECA0002", APD_ADDR(leca_spi_desc) },
+	{ "LECA0003", APD_ADDR(leca_i2c_desc) },
 	{ "NXP0001", APD_ADDR(nxp_i2c_desc) },
 #endif
 	{ }
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
index 3351c4a9ef11..b435b4015f02 100644
--- a/drivers/i2c/busses/i2c-designware-platdrv.c
+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
@@ -279,6 +279,7 @@ static const struct acpi_device_id dw_i2c_acpi_match[] = {
 	{ "INT3432", 0 },
 	{ "INT3433", 0 },
 	{ "INTC10EF", 0 },
+	{ "LECA0003", 0 },
 	{}
 };
 MODULE_DEVICE_TABLE(acpi, dw_i2c_acpi_match);
-- 
2.43.0

Re: [PATCH v4 3/3] i2c: designware: Add ACPI ID LECA0003 for LECARC SoCs

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 550 bytes --]

On Wed, May 20, 2026 at 04:11:36PM +0800, Thomas Lin wrote:
> Add ACPI ID "LECA0003" for LECARC SoCs that integrate
> the DesignWare I2C controller.
> Also add corresponding ACPI description in acpi_apd.c.
> 
> Signed-off-by: Thomas Lin <thomas_lin@lecomputing.com>
> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Because of the dependency, it should probably go in via GPIO or SPI,
right? So:

Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v4 1/3] gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs

[Bartosz Golaszewski]

On Wed, May 20, 2026 at 10:45 AM Thomas Lin <thomas_lin@lecomputing.com> wrote:
>
> Add ACPI ID "LECA0001" for LECARC SoCs that use the DesignWare
> GPIO controller with V1 register offsets.
>
> Signed-off-by: Thomas Lin <thomas_lin@lecomputing.com>
> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Reviewed-by: Bartosz Golaszewski <brgl@kernel.org>
> ---
>  drivers/gpio/gpio-dwapb.c | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/drivers/gpio/gpio-dwapb.c b/drivers/gpio/gpio-dwapb.c
> index 15cebc8b5d66..c1f3d83a67c1 100644
> --- a/drivers/gpio/gpio-dwapb.c
> +++ b/drivers/gpio/gpio-dwapb.c
> @@ -694,6 +694,7 @@ static const struct acpi_device_id dwapb_acpi_match[] = {
>         {"APMC0D07", GPIO_REG_OFFSET_V1},
>         {"APMC0D81", GPIO_REG_OFFSET_V2},
>         {"FUJI200A", GPIO_REG_OFFSET_V1},
> +       {"LECA0001", GPIO_REG_OFFSET_V1},
>         { }
>  };
>  MODULE_DEVICE_TABLE(acpi, dwapb_acpi_match);
> --
> 2.43.0
>

I'm not sure about how to interpret the cover letter - is it fine to
take this independently through the GPIO tree for v7.2?

Bart

Re: [PATCH v4 1/3] gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 323 bytes --]

On Wed, May 20, 2026 at 05:15:12PM +0200, Bartosz Golaszewski wrote:

> I'm not sure about how to interpret the cover letter - is it fine to
> take this independently through the GPIO tree for v7.2?

AFAICT any dependency that exists is runtime only, it's just a bunch of
quirks and none of the patches touch header files.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v4 1/3] gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs

[Wolfram Sang]

[-- Attachment #1: Type: text/plain, Size: 475 bytes --]

On Wed, May 20, 2026 at 04:24:12PM +0100, Mark Brown wrote:
> On Wed, May 20, 2026 at 05:15:12PM +0200, Bartosz Golaszewski wrote:
> 
> > I'm not sure about how to interpret the cover letter - is it fine to
> > take this independently through the GPIO tree for v7.2?
> 
> AFAICT any dependency that exists is runtime only, it's just a bunch of
> quirks and none of the patches touch header files.

Patch 3 depends on patch 2. So, maybe it can go all in via GPIO?


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v4 1/3] gpio: dwapb: Add ACPI ID LECA0001 for LECARC SoCs

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 383 bytes --]

On Wed, May 20, 2026 at 07:11:38PM +0200, Wolfram Sang wrote:
> On Wed, May 20, 2026 at 04:24:12PM +0100, Mark Brown wrote:

> > AFAICT any dependency that exists is runtime only, it's just a bunch of
> > quirks and none of the patches touch header files.

> Patch 3 depends on patch 2. So, maybe it can go all in via GPIO?

Oh, right - you'd end up with a trivial add/add conflict.

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v4 2/3] spi: dw-mmio: Add ACPI ID LECA0002 for LECARC SoCs

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 220 bytes --]

On Wed, May 20, 2026 at 04:11:35PM +0800, Thomas Lin wrote:
> This ID requires a custom initialization function
> dw_spi_hssi_no_dma_init() that sets dws->dws.ip to DW_HSSI_ID.

Acked-by: Mark Brown <broonie@kernel.org>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]