Dekoding encap.txt correct text.

Dekoding encap.txt correct text.

[Janusz Przybylski - SP1LOP]

I greet reading...

I have request whether accessible permissive on decodification software is
file encap.txt
on file routing in format for JNOS 1.11e, because such system on gate of
szczecin.ampr.org
I have installed.

Routingu used in encap format.txt it is not peaceable with my format routing
and then example:
encap.txt
route addprivate 44.165.25/24 encap 80.48.10 5.183

and this routing:
ip route add 44.165.25/25 via 80.48.10 5.183 dev tunl0 onlink

this exemplifies from utilization my data.

I ask about information in this matter on my e-mail
sp1lop@gw.sp1lop.szczecin.pl
I thank warmly, and apologize for my simultaneously very bad English



73 de Janusz SP1LOP
================================
SP1LOP Janusz Przybylski
QTH: Szczecin JO73GL
--------------------------------------------------------------
Member of SPDXC 397/R from 1986
AmprNet: sp1lop.ampr.org       [44.165.25.33]
I am Sysop szczecin.ampr.org [44.165.25.233]
AX25  SP1LOP @ SR1BSZ.SZ.POL.EU
----------------------------------------------------------------
e-mail: sp1lop@gw.sp1lop.szczecin.pl
Web:  http://www.sp1lop.szczecin.pl

6pack problem

[B. Stienstra]

Hello all,

I've recently bought a TNC2multi (www.tnc2multi.de). The eeprom consist
of a 6pack and tf2.7b firmware. You can switch between those two with a
jumper. Since i'm running linux, i thought 6pack would be the best
option. The problem is that the tnc stops running after a long while,
say 8 hours. The /var/log/messages file says: 
Mar 23 10:05:53 atlantic kernel: 6pack: resyncing TNC

After i disconnect the 12volt from the tnc and then reconnect it with
12v the /var/log/messages says:
Mar 23 10:06:18 atlantic kernel: 6pack: TNC found.

And the tnc is up and running. Does anyone know what the problem could
be? Below you can find my system info.

Kind regards,
Ben, PD2BS

--
PC: PIII, 866Mhz, 256MB mem
OS: RedHat Linux 8.0, kernel 2.4.21-pre4
TNC: TNC2multi (6pack/TF2.7b)
AX25 software: ax25-apps-0.0.6, ax25-tools-0.0.8, libax25-0.0.10

Re: 6pack problem

[Wilbert Knol]

Hi Ben,

> option. The problem is that the tnc stops running after a long while,

<snip>

> After i disconnect the 12volt from the tnc and then reconnect it with
> 12v the /var/log/messages says:
> Mar 23 10:06:18 atlantic kernel: 6pack: TNC found.
> 
> And the tnc is up and running. Does anyone know what the problem could

I had exactly the same problem with a TNC2 (Tiny-2). It turned out to be a
hardware problem. I ended up re-flowing every joint on the board. The
problem went away for a few months.
 
Eventually, I replaced the MAX231 RS232<>TTL converter, which cured it.


Wilbert.

Re: 6pack problem

[B. Stienstra]

Hi Wilbert,

Thanks for your reply. To find out if it is a hardware problem here
also, i'm running the tnc in TF2.7b mode (KISS) and let it run for a
long enough time...

Thanks,
Ben