[PATCH v1 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[PATCH v1 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Gabriel Gonzales]

Add support for the Xiaomi Redmi Note 8 based on the SM6125 SoC.

Defined features:
- dmesg output to bootloader preconfigured display
- USB
- eMMC
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons

Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 294 ++++++++++++++++++
 2 files changed, 295 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 140b0b2ab..4d7d54f69 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -246,6 +246,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115p-lenovo-j606f.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-ginkgo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-xiaomi-laurel-sprout.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6375-sony-xperia-murray-pdx225.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
new file mode 100644
index 000000000..c4677cffa
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Gabriel Gonzales <semfault@disroot.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "sm6125.dtsi"
+#include "pm6125.dtsi"
+
+/ {
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <394 0>; /* sm6125 v1 */
+	qcom,board-id = <22 0>;
+
+	model = "Xiaomi Redmi Note 8";
+	compatible = "xiaomi,ginkgo", "qcom,sm6125";
+	chassis-type = "handset";
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer0: framebuffer@5c000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x5c000000 0 (2340 * 1080 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	reserved-memory {
+		debug_mem: debug@ffb00000 {
+			reg = <0x0 0xffb00000 0x0 0xc0000>;
+			no-map;
+		};
+
+		last_log_mem: lastlog@ffbc0000 {
+			reg = <0x0 0xffbc0000 0x0 0x80000>;
+			no-map;
+		};
+
+		pstore_mem: ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc40000 0x0 0xc0000>;
+			record-size = <0x1000>;
+			console-size = <0x40000>;
+			pmsg-size = <0x20000>;
+		};
+
+		cmdline_mem: memory@ffd00000 {
+			reg = <0x0 0xffd40000 0x0 0x1000>;
+			no-map;
+		};
+	};
+
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&vol_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm6125_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+};
+
+&pm6125_gpios {
+	vol_up_n: vol-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&hsusb_phy1 {
+	vdd-supply = <&vreg_l7a>;
+	vdda-pll-supply = <&vreg_l10a>;
+	vdda-phy-dpdm-supply = <&vreg_l15a>;
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm6125-regulators";
+
+		vreg_s6a: s6 {
+			regulator-min-microvolt = <936000>;
+			regulator-max-microvolt = <1422000>;
+		};
+
+		vreg_l1a: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1256000>;
+		};
+
+		vreg_l2a: l2 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1056000>;
+		};
+
+		vreg_l3a: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1064000>;
+		};
+
+		vreg_l4a: l4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l5a: l5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a: l6 {
+			regulator-min-microvolt = <576000>;
+			regulator-max-microvolt = <656000>;
+		};
+
+		vreg_l7a: l7 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+		};
+
+		vreg_l8a: l8 {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <728000>;
+		};
+
+		vreg_l9a: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+		};
+
+		vreg_l10a: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l11a: l11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1952000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l12a: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1996000>;
+		};
+
+		vreg_l13a: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1832000>;
+		};
+
+		vreg_l14a: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l15a: l15 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3232000>;
+		};
+
+		vreg_l16a: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l17a: l17 {
+			regulator-min-microvolt = <1248000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1264000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l19a: l19 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l20a: l20 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l21a: l21 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2856000>;
+		};
+
+		vreg_l22a: l22 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l23a: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+		};
+
+		vreg_l24a: l24 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+	};
+};
+
+&sdc2_off_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&vreg_l24a>;
+	vqmmc-supply = <&vreg_l11a>;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vreg_l22a>;
+	vqmmc-supply = <&vreg_l5a>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <22 2>, <28 6>;
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	extcon = <&extcon_usb>;
+};
-- 
2.47.0

[PATCH v2 0/2] Add Xiaomi Redmi Note 8 support

[Gabriel Gonzales]

This patchset introduces support for the Redmi Note 8 (codenamed ginkgo). This series is a follow-up to v1 (message-id in in-reply-to header) which was sent without a cover letter.

Changes in v2:
- Add missing cover letter
- Fix up commit message for schema

Gabriel Gonzales (2):
  dt-bindings: arm: qcom: Add Xiaomi Redmi Note 8
  arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 294 ++++++++++++++++++
 3 files changed, 296 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts

-- 
2.48.1

[PATCH v2 1/2] dt-bindings: arm: qcom: Add Xiaomi Redmi Note 8

[Gabriel Gonzales]

Document the Xiaomi Redmi Note 8 (codenamed ginkgo),
which is based off the SM6125 SoC.

Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 618a87693..52f7b217b 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1020,6 +1020,7 @@ properties:
       - items:
           - enum:
               - sony,pdx201
+              - xiaomi,ginkgo
               - xiaomi,laurel-sprout
           - const: qcom,sm6125
 
-- 
2.48.1

[PATCH v2 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Gabriel Gonzales]

Add support for the Xiaomi Redmi Note 8 based on the SM6125 SoC.

Defined features:
- dmesg output to bootloader preconfigured display
- USB
- eMMC
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons

Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 294 ++++++++++++++++++
 2 files changed, 295 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 140b0b2ab..4d7d54f69 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -246,6 +246,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115p-lenovo-j606f.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-ginkgo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-xiaomi-laurel-sprout.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6375-sony-xperia-murray-pdx225.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
new file mode 100644
index 000000000..c4677cffa
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
@@ -0,0 +1,294 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Gabriel Gonzales <semfault@disroot.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "sm6125.dtsi"
+#include "pm6125.dtsi"
+
+/ {
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <394 0>; /* sm6125 v1 */
+	qcom,board-id = <22 0>;
+
+	model = "Xiaomi Redmi Note 8";
+	compatible = "xiaomi,ginkgo", "qcom,sm6125";
+	chassis-type = "handset";
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer0: framebuffer@5c000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x5c000000 0 (2340 * 1080 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	reserved-memory {
+		debug_mem: debug@ffb00000 {
+			reg = <0x0 0xffb00000 0x0 0xc0000>;
+			no-map;
+		};
+
+		last_log_mem: lastlog@ffbc0000 {
+			reg = <0x0 0xffbc0000 0x0 0x80000>;
+			no-map;
+		};
+
+		pstore_mem: ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc40000 0x0 0xc0000>;
+			record-size = <0x1000>;
+			console-size = <0x40000>;
+			pmsg-size = <0x20000>;
+		};
+
+		cmdline_mem: memory@ffd00000 {
+			reg = <0x0 0xffd40000 0x0 0x1000>;
+			no-map;
+		};
+	};
+
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&vol_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm6125_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+};
+
+&pm6125_gpios {
+	vol_up_n: vol-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&hsusb_phy1 {
+	vdd-supply = <&vreg_l7a>;
+	vdda-pll-supply = <&vreg_l10a>;
+	vdda-phy-dpdm-supply = <&vreg_l15a>;
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm6125-regulators";
+
+		vreg_s6a: s6 {
+			regulator-min-microvolt = <936000>;
+			regulator-max-microvolt = <1422000>;
+		};
+
+		vreg_l1a: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1256000>;
+		};
+
+		vreg_l2a: l2 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1056000>;
+		};
+
+		vreg_l3a: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1064000>;
+		};
+
+		vreg_l4a: l4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l5a: l5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a: l6 {
+			regulator-min-microvolt = <576000>;
+			regulator-max-microvolt = <656000>;
+		};
+
+		vreg_l7a: l7 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+		};
+
+		vreg_l8a: l8 {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <728000>;
+		};
+
+		vreg_l9a: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+		};
+
+		vreg_l10a: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l11a: l11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1952000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l12a: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1996000>;
+		};
+
+		vreg_l13a: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1832000>;
+		};
+
+		vreg_l14a: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l15a: l15 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3232000>;
+		};
+
+		vreg_l16a: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l17a: l17 {
+			regulator-min-microvolt = <1248000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1264000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l19a: l19 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l20a: l20 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l21a: l21 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2856000>;
+		};
+
+		vreg_l22a: l22 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l23a: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+		};
+
+		vreg_l24a: l24 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+	};
+};
+
+&sdc2_off_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&vreg_l24a>;
+	vqmmc-supply = <&vreg_l11a>;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vreg_l22a>;
+	vqmmc-supply = <&vreg_l5a>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <22 2>, <28 6>;
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	extcon = <&extcon_usb>;
+};
-- 
2.48.1

Re: [PATCH v2 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Konrad Dybcio]

On 8.03.2025 2:30 AM, Gabriel Gonzales wrote:
> Add support for the Xiaomi Redmi Note 8 based on the SM6125 SoC.
> 
> Defined features:
> - dmesg output to bootloader preconfigured display
> - USB
> - eMMC
> - SD card
> - SMD RPM regulators
> - Volume Up, Down and Power buttons
> 
> Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 294 ++++++++++++++++++
>  2 files changed, 295 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 140b0b2ab..4d7d54f69 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -246,6 +246,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6115p-lenovo-j606f.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-ginkgo.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-xiaomi-laurel-sprout.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm6375-sony-xperia-murray-pdx225.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
> new file mode 100644
> index 000000000..c4677cffa
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
> @@ -0,0 +1,294 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2025, Gabriel Gonzales <semfault@disroot.org>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include "sm6125.dtsi"
> +#include "pm6125.dtsi"
> +
> +/ {
> +	/* required for bootloader to select correct board */
> +	qcom,msm-id = <394 0>; /* sm6125 v1 */

#include <dt-bindings/arm/qcom,ids.h>

QCOM_ID_SM6125 and drop the comment

> +	qcom,board-id = <22 0>;

[...]

> +&hsusb_phy1 {
> +	vdd-supply = <&vreg_l7a>;
> +	vdda-pll-supply = <&vreg_l10a>;
> +	vdda-phy-dpdm-supply = <&vreg_l15a>;
> +	status = "okay";

Please add a before 'status', file-wide

[...]

> +&tlmm {
> +	gpio-reserved-ranges = <22 2>, <28 6>;

Would you happen to know what's on the other end of these?

Konrad

Re: [PATCH v2 1/2] dt-bindings: arm: qcom: Add Xiaomi Redmi Note 8

[Krzysztof Kozlowski]

On Sat, Mar 08, 2025 at 09:30:11AM +0800, Gabriel Gonzales wrote:
> Document the Xiaomi Redmi Note 8 (codenamed ginkgo),
> which is based off the SM6125 SoC.
> 

Do not attach (thread) your patchsets to some other threads (unrelated
or older versions). This buries them deep in the mailbox and might
interfere with applying entire sets.

> Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>  1 file changed, 1 insertion(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

<form letter>
This is an automated instruction, just in case, because many review tags
are being ignored. If you know the process, you can skip it (please do
not feel offended by me posting it here - no bad intentions intended).
If you do not know the process, here is a short explanation:

Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions of patchset, under or above your Signed-off-by tag, unless
patch changed significantly (e.g. new properties added to the DT
bindings). Tag is "received", when provided in a message replied to you
on the mailing list. Tools like b4 can help here. However, there's no
need to repost patches *only* to add the tags. The upstream maintainer
will do that for tags received on the version they apply.

https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577
</form letter>

Best regards,
Krzysztof

Re: [PATCH v2 0/2] Add Xiaomi Redmi Note 8 support

[Rob Herring (Arm)]

On Sat, 08 Mar 2025 09:30:10 +0800, Gabriel Gonzales wrote:
> This patchset introduces support for the Redmi Note 8 (codenamed ginkgo). This series is a follow-up to v1 (message-id in in-reply-to header) which was sent without a cover letter.
> 
> Changes in v2:
> - Add missing cover letter
> - Fix up commit message for schema
> 
> Gabriel Gonzales (2):
>   dt-bindings: arm: qcom: Add Xiaomi Redmi Note 8
>   arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo
> 
>  .../devicetree/bindings/arm/qcom.yaml         |   1 +
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 294 ++++++++++++++++++
>  3 files changed, 296 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
> 
> --
> 2.48.1
> 
> 
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20250308013019.10321-1-semfault@disroot.org:

arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dtb: geniqup@4ac0000: #address-cells: 2 was expected
	from schema $id: http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#
arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dtb: geniqup@4ac0000: #size-cells: 2 was expected
	from schema $id: http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#
arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dtb: geniqup@4cc0000: #address-cells: 2 was expected
	from schema $id: http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#
arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dtb: geniqup@4cc0000: #size-cells: 2 was expected
	from schema $id: http://devicetree.org/schemas/soc/qcom/qcom,geni-se.yaml#

Re: [PATCH v2 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Gabriel Gonzales]

On 3/8/25 23:11, Konrad Dybcio wrote:

 > > +&hsusb_phy1 {
 > > +    vdd-supply = <&vreg_l7a>;
 > > +    vdda-pll-supply = <&vreg_l10a>;
 > > +    vdda-phy-dpdm-supply = <&vreg_l15a>;
 >> +    status = "okay";
 > Please add a before 'status', file-wide

'a-status'?

[...]

 > > +&tlmm {
 > > +    gpio-reserved-ranges = <22 2>, <28 6>;

 > Would you happen to know what's on the other end of these?

Unfortunately, no.

[...]

Gabriel

Re: [PATCH v2 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Konrad Dybcio]

On 3/11/25 12:28 AM, Gabriel Gonzales wrote:
> On 3/8/25 23:11, Konrad Dybcio wrote:
> 
>> > +&hsusb_phy1 {
>> > +    vdd-supply = <&vreg_l7a>;
>> > +    vdda-pll-supply = <&vreg_l10a>;
>> > +    vdda-phy-dpdm-supply = <&vreg_l15a>;
>>> +    status = "okay";
>> Please add a before 'status', file-wide
> 
> 'a-status'?

A newline.. the brain didn't synchronize with the hands

> 
> [...]
> 
>> > +&tlmm {
>> > +    gpio-reserved-ranges = <22 2>, <28 6>;
> 
>> Would you happen to know what's on the other end of these?
> 
> Unfortunately, no.

Usually it's some secure i2c connection and pins for the SPI host
that the fingerprint reader sits on

Konrad

Re: [PATCH v2 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Gabriel Gonzales]

On 3/11/25 07:37, Konrad Dybcio wrote:


 > > 'a-status'?

 > A newline.. the brain didn't synchronize with the hands

How about nodes which only have 'status' as a property name? Do they 
still need to be placed before a NL or keep as-is?

[PATCH v3 2/2] arm64: dts: qcom: sm6125: Initial support for xiaomi-ginkgo

[Gabriel Gonzales]

Add support for the Xiaomi Redmi Note 8 based on the SM6125 SoC.

Defined features:
- dmesg output to bootloader preconfigured display
- USB
- eMMC
- SD card
- SMD RPM regulators
- Volume Up, Down and Power buttons

Signed-off-by: Gabriel Gonzales <semfault@disroot.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sm6125-xiaomi-ginkgo.dts    | 295 ++++++++++++++++++
 2 files changed, 296 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 140b0b2ab..4d7d54f69 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -246,6 +246,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm4450-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115-fxtec-pro1x.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6115p-lenovo-j606f.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm6125-xiaomi-ginkgo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-xiaomi-laurel-sprout.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6375-sony-xperia-murray-pdx225.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
new file mode 100644
index 000000000..68a237215
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6125-xiaomi-ginkgo.dts
@@ -0,0 +1,295 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Gabriel Gonzales <semfault@disroot.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/arm/qcom,ids.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "sm6125.dtsi"
+#include "pm6125.dtsi"
+
+/ {
+	model = "Xiaomi Redmi Note 8";
+	compatible = "xiaomi,ginkgo", "qcom,sm6125";
+	chassis-type = "handset";
+
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <QCOM_ID_SM6125>;
+	qcom,board-id = <22 0>;
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer0: framebuffer@5c000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x5c000000 0 (2340 * 1080 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	reserved-memory {
+		debug_mem: debug@ffb00000 {
+			reg = <0x0 0xffb00000 0x0 0xc0000>;
+			no-map;
+		};
+
+		last_log_mem: lastlog@ffbc0000 {
+			reg = <0x0 0xffbc0000 0x0 0x80000>;
+			no-map;
+		};
+
+		pstore_mem: ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc40000 0x0 0xc0000>;
+			record-size = <0x1000>;
+			console-size = <0x40000>;
+			pmsg-size = <0x20000>;
+		};
+
+		cmdline_mem: memory@ffd00000 {
+			reg = <0x0 0xffd40000 0x0 0x1000>;
+			no-map;
+		};
+	};
+
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&vol_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&pm6125_gpios 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+};
+
+&pm6125_gpios {
+	vol_up_n: vol-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&hsusb_phy1 {
+	vdd-supply = <&vreg_l7a>;
+	vdda-pll-supply = <&vreg_l10a>;
+	vdda-phy-dpdm-supply = <&vreg_l15a>;
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm6125-regulators";
+
+		vreg_s6a: s6 {
+			regulator-min-microvolt = <936000>;
+			regulator-max-microvolt = <1422000>;
+		};
+
+		vreg_l1a: l1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1256000>;
+		};
+
+		vreg_l2a: l2 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1056000>;
+		};
+
+		vreg_l3a: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1064000>;
+		};
+
+		vreg_l4a: l4 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l5a: l5 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a: l6 {
+			regulator-min-microvolt = <576000>;
+			regulator-max-microvolt = <656000>;
+		};
+
+		vreg_l7a: l7 {
+			regulator-min-microvolt = <872000>;
+			regulator-max-microvolt = <976000>;
+		};
+
+		vreg_l8a: l8 {
+			regulator-min-microvolt = <400000>;
+			regulator-max-microvolt = <728000>;
+		};
+
+		vreg_l9a: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+		};
+
+		vreg_l10a: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l11a: l11 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1952000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l12a: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1996000>;
+		};
+
+		vreg_l13a: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1832000>;
+		};
+
+		vreg_l14a: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l15a: l15 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3232000>;
+		};
+
+		vreg_l16a: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1904000>;
+		};
+
+		vreg_l17a: l17 {
+			regulator-min-microvolt = <1248000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a: l18 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1264000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l19a: l19 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l20a: l20 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+		};
+
+		vreg_l21a: l21 {
+			regulator-min-microvolt = <2600000>;
+			regulator-max-microvolt = <2856000>;
+		};
+
+		vreg_l22a: l22 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l23a: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3400000>;
+		};
+
+		vreg_l24a: l24 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-allow-set-load;
+		};
+
+	};
+};
+
+&sdc2_off_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd-pins {
+		pins = "gpio98";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&vreg_l24a>;
+	vqmmc-supply = <&vreg_l11a>;
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+	vmmc-supply = <&vreg_l22a>;
+	vqmmc-supply = <&vreg_l5a>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <22 2>, <28 6>;
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	extcon = <&extcon_usb>;
+};
-- 
2.48.1