Re: [PATCH v1 0/7] Add support to load QUP SE firmware from

[Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>]

Thanks Caleb for your testing and sharing results. Since Viken is on 
leave, i am following on this.

On 1/7/2025 4:55 PM, Caleb Connolly wrote:
> Hi Viken,
> 
> On 04/12/2024 16:03, Viken Dadhaniya wrote:
>> In Qualcomm SoCs, firmware loading for Serial Engines (SE) in the QUP
>> hardware has traditionally been managed by TrustZone (TZ). This setup
>> handled Serial Engines(SE) assignments and access control permissions,
>> ensuring a high level of security but limiting flexibility and
>> accessibility.
>>   
>> This limitation poses a significant challenge for developers who need more
>> flexibility to enable any protocol on any of the SEs within the QUP
>> hardware.
>>   
>> To address this, we are introducing a change that opens the firmware
>> loading mechanism to the Linux environment. This enhancement increases
>> flexibility and allows for more streamlined and efficient management. We
>> can now handle SE assignments and access control permissions directly
>> within Linux, eliminating the dependency on TZ.
>>   
>> We propose an alternative method for firmware loading and SE
>> ownership/transfer mode configuration based on device tree configuration.
>> This method does not rely on other execution environments, making it
>> accessible to all developers.
>>   
>> For SEs used prior to the kernel, their firmware will be loaded by the
>> respective image drivers (e.g., Debug UART, Secure or trusted SE).
>> Additionally, the GSI firmware, which is common to all SEs per QUPV3 core,
>> will not be loaded by Linux driver but TZ only. At the kernel level, only
>> the SE protocol driver should load the respective protocol firmware.
> 
> I gave this series a spin on the RB3 Gen 2 with U-Boot.
> 
Is it possible to try on RB8 board ? Because that's where this support 
is enabled. It also needs respective TZ configuration to allow FW 
loading from Linux.


> After fixing the compilation errors, it seems like there is a consistent
> hard crash (the board freezes and resets) at some point during i2c
> controller init with this series.
> 
Can you please share exact repro steps ? We can try locally and check 
what's wrong and also review in future how we make it working for U-boot 
combination.
> I noticed a similar issue with this same logic implemented in U-Boot.
> 
> Could you clarify which xfer mode is appropriate for the i2c controllers
> on the RB3 Gen 2 and maybe give this a try yourself, or let me know what
> other info you'd need to debug this.
> 
Yes, please share the procedure , we will try internally.
is there any DTSI change done as part of your testing ?
> Thanks and kind regards,
>>
>> Viken Dadhaniya (7):
>>    dt-bindings: i2c: qcom,i2c-geni: Document DT properties for QUP
>>      firmware loading
>>    spi: dt-bindings: Document DT properties for QUP firmware loading
>>    dt-bindings: serial: Document DT properties for QUP firmware loading
>>    soc: qcom: geni-se:: Add support to load QUP SE Firmware via Linux
>>      subsystem
>>    i2c: qcom-geni: Load i2c qup Firmware from linux side
>>    spi: geni-qcom: Load spi qup Firmware from linux side
>>    serial: qcom-geni: Load UART qup Firmware from linux side
>>
>>   .../bindings/i2c/qcom,i2c-geni-qcom.yaml      |  11 +
>>   .../serial/qcom,serial-geni-qcom.yaml         |  12 +
>>   .../bindings/spi/qcom,spi-geni-qcom.yaml      |  11 +
>>   drivers/i2c/busses/i2c-qcom-geni.c            |  11 +-
>>   drivers/soc/qcom/qcom-geni-se.c               | 445 ++++++++++++++++++
>>   drivers/spi/spi-geni-qcom.c                   |   7 +-
>>   drivers/tty/serial/qcom_geni_serial.c         |   7 +-
>>   include/linux/soc/qcom/geni-se.h              |  17 +
>>   include/linux/soc/qcom/qup-fw-load.h          | 179 +++++++
>>   9 files changed, 692 insertions(+), 8 deletions(-)
>>   create mode 100644 include/linux/soc/qcom/qup-fw-load.h
>>
>