From: Biwen Li <biwen.li@nxp.com>
To: peda@axentia.se, leoyang.li@nxp.com, robh+dt@kernel.org,
mark.rutland@arm.com
Cc: linux-i2c@vger.kernel.org, linux-kernel@vger.kernel.org,
devicetree@vger.kernel.org, Biwen Li <biwen.li@nxp.com>
Subject: [PATCH 2/2] i2c: mux: pca954x: replace property i2c-mux-idle-disconnect
Date: Mon, 14 Oct 2019 19:25:58 +0800 [thread overview]
Message-ID: <20191014112558.3881-2-biwen.li@nxp.com> (raw)
In-Reply-To: <20191014112558.3881-1-biwen.li@nxp.com>
This replaces property i2c-mux-idle-disconnect with idle-state
Signed-off-by: Biwen Li <biwen.li@nxp.com>
---
drivers/i2c/muxes/i2c-mux-pca954x.c | 44 ++++++++++++++++++++---------
1 file changed, 31 insertions(+), 13 deletions(-)
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index 923aa3a5a3dc..a330929c4d67 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -86,7 +86,7 @@ struct pca954x {
u8 last_chan; /* last register value */
/* MUX_IDLE_AS_IS, MUX_IDLE_DISCONNECT or >= 0 for channel */
- s8 idle_state;
+ s32 idle_state;
struct i2c_client *client;
@@ -256,7 +256,7 @@ static int pca954x_deselect_mux(struct i2c_mux_core *muxc, u32 chan)
{
struct pca954x *data = i2c_mux_priv(muxc);
struct i2c_client *client = data->client;
- s8 idle_state;
+ s32 idle_state;
idle_state = READ_ONCE(data->idle_state);
if (idle_state >= 0)
@@ -411,7 +411,6 @@ static int pca954x_probe(struct i2c_client *client,
struct i2c_adapter *adap = client->adapter;
struct device *dev = &client->dev;
struct device_node *np = dev->of_node;
- bool idle_disconnect_dt;
struct gpio_desc *gpio;
struct i2c_mux_core *muxc;
struct pca954x *data;
@@ -462,22 +461,31 @@ static int pca954x_probe(struct i2c_client *client,
}
}
+ if (of_property_read_u32(np, "idle-state", &data->idle_state))
+ data->idle_state = MUX_IDLE_AS_IS;
+
/* Write the mux register at addr to verify
* that the mux is in fact present. This also
* initializes the mux to disconnected state.
*/
- if (i2c_smbus_write_byte(client, 0) < 0) {
+ if (data->idle_state >= 0){
+ data->last_chan = data->idle_state;
+ /* Always enable multiplexer */
+ ret = i2c_smbus_write_byte(client, data->last_chan |
+ (data->chip->muxtype == pca954x_ismux ?
+ data->chip->enable : 0));
+ }
+ else{
+ data->last_chan = 0; /* force the first selection */
+ /* Disconnect multiplexer */
+ ret = i2c_smbus_write_byte(client, data->last_chan);
+ }
+
+ if (ret < 0) {
dev_warn(dev, "probe failed\n");
return -ENODEV;
}
- data->last_chan = 0; /* force the first selection */
- data->idle_state = MUX_IDLE_AS_IS;
-
- idle_disconnect_dt = np &&
- of_property_read_bool(np, "i2c-mux-idle-disconnect");
- if (idle_disconnect_dt)
- data->idle_state = MUX_IDLE_DISCONNECT;
ret = pca954x_irq_setup(muxc);
if (ret)
@@ -531,8 +539,18 @@ static int pca954x_resume(struct device *dev)
struct i2c_mux_core *muxc = i2c_get_clientdata(client);
struct pca954x *data = i2c_mux_priv(muxc);
- data->last_chan = 0;
- return i2c_smbus_write_byte(client, 0);
+ if (data->idle_state >= 0){
+ data->last_chan = data->idle_state;
+ /* Always enable multiplexer */
+ return i2c_smbus_write_byte(client, data->last_chan |
+ (data->chip->muxtype == pca954x_ismux ?
+ data->chip->enable : 0));
+ }
+ else{
+ data->last_chan = 0;
+ /* Disconnect multiplexer */
+ return i2c_smbus_write_byte(client, data->last_chan);
+ }
}
#endif
--
2.17.1
next prev parent reply other threads:[~2019-10-14 11:25 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-14 11:25 [PATCH 1/2] dt-bindings: i2c: replace property i2c-mux-idle-disconnect Biwen Li
2019-10-14 11:25 ` Biwen Li [this message]
2019-10-14 16:03 ` [PATCH 2/2] i2c: mux: pca954x: " Peter Rosin
2019-10-15 3:17 ` [EXT] " Biwen Li
2019-10-14 11:41 ` [PATCH 1/2] dt-bindings: i2c: " Biwen Li
2019-10-14 15:44 ` Peter Rosin
2019-10-15 3:18 ` [EXT] " Biwen Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191014112558.3881-2-biwen.li@nxp.com \
--to=biwen.li@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=peda@axentia.se \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox