* [PATCH v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML
2026-04-15 5:14 [PATCH v29 0/4] Add ASPEED AST2600 I2C controller driver Ryan Chen
@ 2026-04-15 5:14 ` Ryan Chen
2026-04-15 15:16 ` Conor Dooley
2026-04-15 5:14 ` [PATCH v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties Ryan Chen
` (2 subsequent siblings)
3 siblings, 1 reply; 7+ messages in thread
From: Ryan Chen @ 2026-04-15 5:14 UTC (permalink / raw)
To: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, openbmc, Ryan Chen
The AST2600 I2C controller introduces a completely new register layout
with separate controller and target register blocks, unlike the mixed
register layout used by AST2400/AST2500.
Move AST2600 I2C binding from aspeed,i2c.yaml to a dedicated
aspeed,ast2600-i2c.yaml schema.
Besides the split, this also adjusts for AST2600-specific requirements.
- require two reg regions (controller register block + buffer block)
- use clock-frequency for bus speed description
- interrupts are required on AST2600
- use correct DTS coding style in example
No compatible strings are changed.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
---
Changes in v26:
- commit message: include details of changes from original binding
- fix example property ordering to follow DTS coding style
- use consistent "AST2600" naming
---
.../bindings/i2c/aspeed,ast2600-i2c.yaml | 62 ++++++++++++++++++++++
.../devicetree/bindings/i2c/aspeed,i2c.yaml | 3 +-
2 files changed, 63 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
new file mode 100644
index 000000000000..de2c359037da
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/aspeed,ast2600-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASPEED I2C on the AST2600 SoCs
+
+maintainers:
+ - Ryan Chen <ryan_chen@aspeedtech.com>
+
+allOf:
+ - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+ compatible:
+ enum:
+ - aspeed,ast2600-i2c-bus
+
+ reg:
+ items:
+ - description: controller registers
+ - description: controller buffer space
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ clock-frequency:
+ description: Desired operating frequency of the I2C bus in Hz.
+ minimum: 500
+ maximum: 4000000
+ default: 100000
+
+ resets:
+ maxItems: 1
+
+required:
+ - reg
+ - compatible
+ - clocks
+ - resets
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/aspeed-clock.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ i2c@80 {
+ compatible = "aspeed,ast2600-i2c-bus";
+ reg = <0x80 0x80>, <0xc00 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&syscon ASPEED_CLK_APB>;
+ resets = <&syscon ASPEED_RESET_I2C>;
+ clock-frequency = <100000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ };
diff --git a/Documentation/devicetree/bindings/i2c/aspeed,i2c.yaml b/Documentation/devicetree/bindings/i2c/aspeed,i2c.yaml
index 5b9bd2feda3b..d4e4f412feba 100644
--- a/Documentation/devicetree/bindings/i2c/aspeed,i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/aspeed,i2c.yaml
@@ -4,7 +4,7 @@
$id: http://devicetree.org/schemas/i2c/aspeed,i2c.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: ASPEED I2C on the AST24XX, AST25XX, and AST26XX SoCs
+title: ASPEED I2C on the AST24XX, AST25XX SoCs
maintainers:
- Rayn Chen <rayn_chen@aspeedtech.com>
@@ -17,7 +17,6 @@ properties:
enum:
- aspeed,ast2400-i2c-bus
- aspeed,ast2500-i2c-bus
- - aspeed,ast2600-i2c-bus
reg:
minItems: 1
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML
2026-04-15 5:14 ` [PATCH v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML Ryan Chen
@ 2026-04-15 15:16 ` Conor Dooley
0 siblings, 0 replies; 7+ messages in thread
From: Conor Dooley @ 2026-04-15 15:16 UTC (permalink / raw)
To: Ryan Chen
Cc: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel, linux-i2c,
devicetree, linux-arm-kernel, linux-aspeed, linux-kernel, openbmc
[-- Attachment #1: Type: text/plain, Size: 821 bytes --]
On Wed, Apr 15, 2026 at 01:14:02PM +0800, Ryan Chen wrote:
> The AST2600 I2C controller introduces a completely new register layout
> with separate controller and target register blocks, unlike the mixed
> register layout used by AST2400/AST2500.
>
> Move AST2600 I2C binding from aspeed,i2c.yaml to a dedicated
> aspeed,ast2600-i2c.yaml schema.
>
> Besides the split, this also adjusts for AST2600-specific requirements.
> - require two reg regions (controller register block + buffer block)
> - use clock-frequency for bus speed description
> - interrupts are required on AST2600
> - use correct DTS coding style in example
>
> No compatible strings are changed.
>
> Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties
2026-04-15 5:14 [PATCH v29 0/4] Add ASPEED AST2600 I2C controller driver Ryan Chen
2026-04-15 5:14 ` [PATCH v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML Ryan Chen
@ 2026-04-15 5:14 ` Ryan Chen
2026-04-15 15:19 ` Conor Dooley
2026-04-15 5:14 ` [PATCH v29 3/4] i2c: ast2600: Add controller driver for AST2600 new register set Ryan Chen
2026-04-15 5:14 ` [PATCH v29 4/4] i2c: ast2600: Add target mode support Ryan Chen
3 siblings, 1 reply; 7+ messages in thread
From: Ryan Chen @ 2026-04-15 5:14 UTC (permalink / raw)
To: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, openbmc, Ryan Chen
Add the aspeed,global-regs phandle to reference the AST2600 global
registers syscon node, containing the SoC-common I2C register set.
These properties apply only to the AST2600 binding. Legacy DTs remain
unchanged.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
---
Changes in v29:
- remove aspeed,enable-dma properties.
Changes in v28:
- update commit message correspond with aspeed,enable-dma.
- remove aspeed,transfer-mode and add aspeed,enable-dma property and
description.
- Fix aspeed,enable-dma description to reflect hardware capability rather
than software behavior
Changes in v27:
- change aspeed,transfer-mode to aspeed,enable-dma.
---
Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
index de2c359037da..0c769efb76a5 100644
--- a/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
@@ -37,6 +37,12 @@ properties:
resets:
maxItems: 1
+ aspeed,global-regs:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ Phandle reference to the i2c global syscon node, containing the
+ SoC-common i2c register set.
+
required:
- reg
- compatible
@@ -59,4 +65,5 @@ examples:
resets = <&syscon ASPEED_RESET_I2C>;
clock-frequency = <100000>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ aspeed,global-regs = <&i2c_global>;
};
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties
2026-04-15 5:14 ` [PATCH v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties Ryan Chen
@ 2026-04-15 15:19 ` Conor Dooley
0 siblings, 0 replies; 7+ messages in thread
From: Conor Dooley @ 2026-04-15 15:19 UTC (permalink / raw)
To: Ryan Chen
Cc: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel, linux-i2c,
devicetree, linux-arm-kernel, linux-aspeed, linux-kernel, openbmc
[-- Attachment #1: Type: text/plain, Size: 2088 bytes --]
On Wed, Apr 15, 2026 at 01:14:03PM +0800, Ryan Chen wrote:
> Add the aspeed,global-regs phandle to reference the AST2600 global
> registers syscon node, containing the SoC-common I2C register set.
>
> These properties apply only to the AST2600 binding. Legacy DTs remain
> unchanged.
>
> Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
I hate to do it to you on v29, but can you please explain what this
"soc-common i2c register set" actually is/does in your commit message.
The patch seems fine, so with that
Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable
> ---
> Changes in v29:
> - remove aspeed,enable-dma properties.
>
> Changes in v28:
> - update commit message correspond with aspeed,enable-dma.
> - remove aspeed,transfer-mode and add aspeed,enable-dma property and
> description.
> - Fix aspeed,enable-dma description to reflect hardware capability rather
> than software behavior
>
> Changes in v27:
> - change aspeed,transfer-mode to aspeed,enable-dma.
> ---
> Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
> index de2c359037da..0c769efb76a5 100644
> --- a/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
> +++ b/Documentation/devicetree/bindings/i2c/aspeed,ast2600-i2c.yaml
> @@ -37,6 +37,12 @@ properties:
> resets:
> maxItems: 1
>
> + aspeed,global-regs:
> + $ref: /schemas/types.yaml#/definitions/phandle
> + description:
> + Phandle reference to the i2c global syscon node, containing the
> + SoC-common i2c register set.
> +
> required:
> - reg
> - compatible
> @@ -59,4 +65,5 @@ examples:
> resets = <&syscon ASPEED_RESET_I2C>;
> clock-frequency = <100000>;
> interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> + aspeed,global-regs = <&i2c_global>;
> };
>
> --
> 2.34.1
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v29 3/4] i2c: ast2600: Add controller driver for AST2600 new register set
2026-04-15 5:14 [PATCH v29 0/4] Add ASPEED AST2600 I2C controller driver Ryan Chen
2026-04-15 5:14 ` [PATCH v29 1/4] dt-bindings: i2c: Split AST2600 binding into a new YAML Ryan Chen
2026-04-15 5:14 ` [PATCH v29 2/4] dt-bindings: i2c: ast2600-i2c.yaml: Add global-regs properties Ryan Chen
@ 2026-04-15 5:14 ` Ryan Chen
2026-04-15 5:14 ` [PATCH v29 4/4] i2c: ast2600: Add target mode support Ryan Chen
3 siblings, 0 replies; 7+ messages in thread
From: Ryan Chen @ 2026-04-15 5:14 UTC (permalink / raw)
To: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, openbmc, Ryan Chen
The AST2600 introduces a new I2C controller register layout, selectable
at runtime via global control registers. Compared to the legacy layout
used on AST2400/AST2500, the new layout separates controller (master)
and target (slave) registers and adds support for packet-based transfers
The new register set extends the hardware capabilities with:
- Enhanced clock divider configuration for improved timing precision
- tCKHighMin timing control for SCL high pulse width
- Dual pool buffer mode (separate Tx/Rx buffers)
- Hardware-assisted bus recovery and timeout mechanisms
This patch adds an AST2600-specific I2C controller driver implementing
the new register layout, including support for packet-based transfers.
The legacy and new register layouts represent the same AST2600 I2C
controller IP and therefore share the existing compatible string:
"aspeed,ast2600-i2c-bus"
To preserve DT ABI compatibility, driver selection is performed at probe
time based on DT contents. In particular, the new binding requires the
`aspeed,global-regs` phandle, which is absent from legacy DTBs:
- The new driver only probes successfully when `aspeed,global-regs` is
present.
- The existing i2c-aspeed driver returns -ENODEV for AST2600 nodes that
provide `aspeed,global-regs`, allowing the new driver to bind.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
---
Changes in v29:
- update commit message remove transfer mode selection.
- remove dma/byte transfer, use buffer mode only.
- remove sysfs file.
- remove define I2C_TARGET_MSG_BUF_SIZE and AST2600_I2C_DMA_SIZE.
- remove buf_index in struct ast2600_i2c_bus.
Changes in v28:
- Separate xfer_mode_store into distinct parse and availability-check
steps by introducing ast2600_i2c_xfer_mode_check()
- fix tx dma memcpy source point address.
- Use a temporary variable for devm_platform_get_and_ioremap_resource()
to avoid storing an ERR_PTR in i2c_bus->buf_base; drop the redundant
NULL assignment in the error path since i2c_bus is kzalloc()ed
- Add ABI documentation file
Documentation/ABI/testing/sysfs-driver-ast2600-i2c
Changes in v27:
- remove aspeed,transfer-mode selection instead aspeed,dma-mode.
- add sysfs for xfer mode.
Changes in v25:
- Rename AST2600_I2CM_SMBUS_ALT to AST2600_I2CM_SMBUS_ALERT.
- Refactor transfer mode handling using setup_tx/setup_rx helpers.
- Rework DMA handling to use pre-allocated buffers and reduce
mapping overhead in interrupt context.
- Fix IRQ status checks to use consistent (sts & value) style.
- Move device_property_read_bool() to probe().
- Improve probe error handling.
- Handle timeout condition in target_byte_irq().
- Rename "package" to "packet".
- Remove target reset when master wait_for_completion_timeout().
---
drivers/i2c/busses/Makefile | 2 +-
drivers/i2c/busses/i2c-aspeed.c | 5 +
drivers/i2c/busses/i2c-ast2600.c | 808 +++++++++++++++++++++++++++++++++++++++
3 files changed, 814 insertions(+), 1 deletion(-)
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 547123ab351f..ece201a67d41 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -37,7 +37,7 @@ obj-$(CONFIG_I2C_POWERMAC) += i2c-powermac.o
obj-$(CONFIG_I2C_ALTERA) += i2c-altera.o
obj-$(CONFIG_I2C_AMD_MP2) += i2c-amd-mp2-pci.o i2c-amd-mp2-plat.o
obj-$(CONFIG_I2C_AMD_ASF) += i2c-amd-asf-plat.o
-obj-$(CONFIG_I2C_ASPEED) += i2c-aspeed.o
+obj-$(CONFIG_I2C_ASPEED) += i2c-aspeed.o i2c-ast2600.o
obj-$(CONFIG_I2C_AT91) += i2c-at91.o
i2c-at91-y := i2c-at91-core.o i2c-at91-master.o
i2c-at91-$(CONFIG_I2C_AT91_SLAVE_EXPERIMENTAL) += i2c-at91-slave.o
diff --git a/drivers/i2c/busses/i2c-aspeed.c b/drivers/i2c/busses/i2c-aspeed.c
index a26b74c71206..8286fd2cd130 100644
--- a/drivers/i2c/busses/i2c-aspeed.c
+++ b/drivers/i2c/busses/i2c-aspeed.c
@@ -22,6 +22,7 @@
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
+#include <linux/property.h>
#include <linux/reset.h>
#include <linux/slab.h>
@@ -1002,6 +1003,10 @@ static int aspeed_i2c_probe_bus(struct platform_device *pdev)
struct clk *parent_clk;
int irq, ret;
+ if (device_is_compatible(&pdev->dev, "aspeed,ast2600-i2c-bus") &&
+ device_property_present(&pdev->dev, "aspeed,global-regs"))
+ return -ENODEV;
+
bus = devm_kzalloc(&pdev->dev, sizeof(*bus), GFP_KERNEL);
if (!bus)
return -ENOMEM;
diff --git a/drivers/i2c/busses/i2c-ast2600.c b/drivers/i2c/busses/i2c-ast2600.c
new file mode 100644
index 000000000000..787ef6bd6244
--- /dev/null
+++ b/drivers/i2c/busses/i2c-ast2600.c
@@ -0,0 +1,808 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ASPEED AST2600 new register set I2C controller driver
+ *
+ * Copyright (C) 2026 ASPEED Technology Inc.
+ */
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/i2c-smbus.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/minmax.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/unaligned.h>
+
+#define AST2600_I2CG_ISR 0x00
+#define AST2600_I2CG_SLAVE_ISR 0x04
+#define AST2600_I2CG_OWNER 0x08
+#define AST2600_I2CG_CTRL 0x0C
+#define AST2600_I2CG_CLK_DIV_CTRL 0x10
+
+#define AST2600_I2CG_SLAVE_PKT_NAK BIT(4)
+#define AST2600_I2CG_M_S_SEPARATE_INTR BIT(3)
+#define AST2600_I2CG_CTRL_NEW_REG BIT(2)
+#define AST2600_I2CG_CTRL_NEW_CLK_DIV BIT(1)
+#define AST2600_GLOBAL_INIT \
+ (AST2600_I2CG_CTRL_NEW_REG | AST2600_I2CG_CTRL_NEW_CLK_DIV)
+/*
+ * APB clk : 100Mhz
+ * div : scl : baseclk [APB/((div/2) + 1)] : tBuf [1/bclk * 16]
+ * I2CG10[31:24] base clk4 for i2c auto recovery timeout counter (0xC6)
+ * I2CG10[23:16] base clk3 for Standard-mode (100Khz) min tBuf 4.7us
+ * 0x3c : 100.8Khz : 3.225Mhz : 4.96us
+ * 0x3d : 99.2Khz : 3.174Mhz : 5.04us
+ * 0x3e : 97.65Khz : 3.125Mhz : 5.12us
+ * 0x40 : 97.75Khz : 3.03Mhz : 5.28us
+ * 0x41 : 99.5Khz : 2.98Mhz : 5.36us (default)
+ * I2CG10[15:8] base clk2 for Fast-mode (400Khz) min tBuf 1.3us
+ * 0x12 : 400Khz : 10Mhz : 1.6us
+ * I2CG10[7:0] base clk1 for Fast-mode Plus (1Mhz) min tBuf 0.5us
+ * 0x08 : 1Mhz : 20Mhz : 0.8us
+ */
+#define I2CCG_DIV_CTRL 0xC6411208
+
+/* 0x00 : I2CC Controller/Target Function Control Register */
+#define AST2600_I2CC_FUN_CTRL 0x00
+#define AST2600_I2CC_SLAVE_ADDR_RX_EN BIT(20)
+#define AST2600_I2CC_MASTER_RETRY_MASK GENMASK(19, 18)
+#define AST2600_I2CC_MASTER_RETRY(x) (((x) & GENMASK(1, 0)) << 18)
+#define AST2600_I2CC_BUS_AUTO_RELEASE BIT(17)
+#define AST2600_I2CC_M_SDA_LOCK_EN BIT(16)
+#define AST2600_I2CC_MULTI_MASTER_DIS BIT(15)
+#define AST2600_I2CC_M_SCL_DRIVE_EN BIT(14)
+#define AST2600_I2CC_MSB_STS BIT(9)
+#define AST2600_I2CC_SDA_DRIVE_1T_EN BIT(8)
+#define AST2600_I2CC_M_SDA_DRIVE_1T_EN BIT(7)
+#define AST2600_I2CC_M_HIGH_SPEED_EN BIT(6)
+/* reserver 5 : 2 */
+#define AST2600_I2CC_SLAVE_EN BIT(1)
+#define AST2600_I2CC_MASTER_EN BIT(0)
+
+/* 0x04 : I2CC Controller/Target Clock and AC Timing Control Register #1 */
+#define AST2600_I2CC_AC_TIMING 0x04
+#define AST2600_I2CC_TTIMEOUT(x) (((x) & GENMASK(4, 0)) << 24)
+#define AST2600_I2CC_TCKHIGHMIN(x) (((x) & GENMASK(3, 0)) << 20)
+#define AST2600_I2CC_TCKHIGH(x) (((x) & GENMASK(3, 0)) << 16)
+#define AST2600_I2CC_TCKLOW(x) (((x) & GENMASK(3, 0)) << 12)
+#define AST2600_I2CC_THDDAT(x) (((x) & GENMASK(1, 0)) << 10)
+#define AST2600_I2CC_TOUTBASECLK(x) (((x) & GENMASK(1, 0)) << 8)
+#define AST2600_I2CC_TBASECLK(x) ((x) & GENMASK(3, 0))
+#define AST2600_I2CC_AC_TIMING_MASK GENMASK(23, 0)
+
+/* 0x08 : I2CC Controller/Target Transmit/Receive Byte Buffer Register */
+#define AST2600_I2CC_STS_AND_BUFF 0x08
+#define AST2600_I2CC_TX_DIR_MASK GENMASK(31, 29)
+#define AST2600_I2CC_SDA_OE BIT(28)
+#define AST2600_I2CC_SDA_O BIT(27)
+#define AST2600_I2CC_SCL_OE BIT(26)
+#define AST2600_I2CC_SCL_O BIT(25)
+
+#define AST2600_I2CC_SCL_LINE_STS BIT(18)
+#define AST2600_I2CC_SDA_LINE_STS BIT(17)
+#define AST2600_I2CC_BUS_BUSY_STS BIT(16)
+
+#define AST2600_I2CC_GET_RX_BUFF(x) (((x) >> 8) & GENMASK(7, 0))
+
+/* 0x0C : I2CC Controller/Target Pool Buffer Control Register */
+#define AST2600_I2CC_BUFF_CTRL 0x0C
+#define AST2600_I2CC_GET_RX_BUF_LEN(x) (((x) & GENMASK(29, 24)) >> 24)
+#define AST2600_I2CC_SET_RX_BUF_LEN(x) (((((x) - 1) & GENMASK(4, 0)) << 16) | BIT(0))
+#define AST2600_I2CC_SET_TX_BUF_LEN(x) (((((x) - 1) & GENMASK(4, 0)) << 8) | BIT(0))
+#define AST2600_I2CC_GET_TX_BUF_LEN(x) ((((x) & GENMASK(12, 8)) >> 8) + 1)
+
+/* 0x10 : I2CM Controller Interrupt Control Register */
+#define AST2600_I2CM_IER 0x10
+/* 0x14 : I2CM Controller Interrupt Status Register : WC */
+#define AST2600_I2CM_ISR 0x14
+
+#define AST2600_I2CM_PKT_TIMEOUT BIT(18)
+#define AST2600_I2CM_PKT_ERROR BIT(17)
+#define AST2600_I2CM_PKT_DONE BIT(16)
+
+#define AST2600_I2CM_BUS_RECOVER_FAIL BIT(15)
+#define AST2600_I2CM_SDA_DL_TO BIT(14)
+#define AST2600_I2CM_BUS_RECOVER BIT(13)
+#define AST2600_I2CM_SMBUS_ALERT BIT(12)
+
+#define AST2600_I2CM_SCL_LOW_TO BIT(6)
+#define AST2600_I2CM_ABNORMAL BIT(5)
+#define AST2600_I2CM_NORMAL_STOP BIT(4)
+#define AST2600_I2CM_ARBIT_LOSS BIT(3)
+#define AST2600_I2CM_RX_DONE BIT(2)
+#define AST2600_I2CM_TX_NAK BIT(1)
+#define AST2600_I2CM_TX_ACK BIT(0)
+
+/* 0x18 : I2CM Controller Command/Status Register */
+#define AST2600_I2CM_CMD_STS 0x18
+#define AST2600_I2CM_PKT_ADDR(x) (((x) & GENMASK(6, 0)) << 24)
+#define AST2600_I2CM_PKT_EN BIT(16)
+#define AST2600_I2CM_SDA_OE_OUT_DIR BIT(15)
+#define AST2600_I2CM_SDA_O_OUT_DIR BIT(14)
+#define AST2600_I2CM_SCL_OE_OUT_DIR BIT(13)
+#define AST2600_I2CM_SCL_O_OUT_DIR BIT(12)
+#define AST2600_I2CM_RECOVER_CMD_EN BIT(11)
+
+#define AST2600_I2CM_RX_DMA_EN BIT(9)
+#define AST2600_I2CM_TX_DMA_EN BIT(8)
+/* Command Bit */
+#define AST2600_I2CM_RX_BUFF_EN BIT(7)
+#define AST2600_I2CM_TX_BUFF_EN BIT(6)
+#define AST2600_I2CM_STOP_CMD BIT(5)
+#define AST2600_I2CM_RX_CMD_LAST BIT(4)
+#define AST2600_I2CM_RX_CMD BIT(3)
+
+#define AST2600_I2CM_TX_CMD BIT(1)
+#define AST2600_I2CM_START_CMD BIT(0)
+
+/* 0x1C : I2CM Controller DMA Transfer Length Register */
+#define AST2600_I2CM_DMA_LEN 0x1C
+/* Tx Rx support length 1 ~ 4096 */
+#define AST2600_I2CM_SET_RX_DMA_LEN(x) ((((x) & GENMASK(11, 0)) << 16) | BIT(31))
+#define AST2600_I2CM_SET_TX_DMA_LEN(x) (((x) & GENMASK(11, 0)) | BIT(15))
+
+/* 0x20 : I2CS Target Interrupt Control Register */
+#define AST2600_I2CS_IER 0x20
+/* 0x24 : I2CS Target Interrupt Status Register */
+#define AST2600_I2CS_ISR 0x24
+
+#define AST2600_I2CS_ADDR_INDICATE_MASK GENMASK(31, 30)
+#define AST2600_I2CS_SLAVE_PENDING BIT(29)
+
+#define AST2600_I2CS_WAIT_TX_DMA BIT(25)
+#define AST2600_I2CS_WAIT_RX_DMA BIT(24)
+
+#define AST2600_I2CS_ADDR3_NAK BIT(22)
+#define AST2600_I2CS_ADDR2_NAK BIT(21)
+#define AST2600_I2CS_ADDR1_NAK BIT(20)
+
+#define AST2600_I2CS_ADDR_MASK GENMASK(19, 18)
+#define AST2600_I2CS_PKT_ERROR BIT(17)
+#define AST2600_I2CS_PKT_DONE BIT(16)
+#define AST2600_I2CS_INACTIVE_TO BIT(15)
+
+#define AST2600_I2CS_SLAVE_MATCH BIT(7)
+#define AST2600_I2CS_ABNOR_STOP BIT(5)
+#define AST2600_I2CS_STOP BIT(4)
+#define AST2600_I2CS_RX_DONE_NAK BIT(3)
+#define AST2600_I2CS_RX_DONE BIT(2)
+#define AST2600_I2CS_TX_NAK BIT(1)
+#define AST2600_I2CS_TX_ACK BIT(0)
+
+/* 0x28 : I2CS Target CMD/Status Register */
+#define AST2600_I2CS_CMD_STS 0x28
+#define AST2600_I2CS_ACTIVE_ALL GENMASK(18, 17)
+#define AST2600_I2CS_PKT_MODE_EN BIT(16)
+#define AST2600_I2CS_AUTO_NAK_NOADDR BIT(15)
+#define AST2600_I2CS_AUTO_NAK_EN BIT(14)
+
+#define AST2600_I2CS_ALT_EN BIT(10)
+#define AST2600_I2CS_RX_DMA_EN BIT(9)
+#define AST2600_I2CS_TX_DMA_EN BIT(8)
+#define AST2600_I2CS_RX_BUFF_EN BIT(7)
+#define AST2600_I2CS_TX_BUFF_EN BIT(6)
+#define AST2600_I2CS_RX_CMD_LAST BIT(4)
+
+#define AST2600_I2CS_TX_CMD BIT(2)
+
+#define AST2600_I2CS_DMA_LEN 0x2C
+#define AST2600_I2CS_SET_RX_DMA_LEN(x) (((((x) - 1) & GENMASK(11, 0)) << 16) | BIT(31))
+#define AST2600_I2CS_SET_TX_DMA_LEN(x) ((((x) - 1) & GENMASK(11, 0)) | BIT(15))
+
+/* I2CM Controller DMA Tx Buffer Register */
+#define AST2600_I2CM_TX_DMA 0x30
+/* I2CM Controller DMA Rx Buffer Register */
+#define AST2600_I2CM_RX_DMA 0x34
+/* I2CS Target DMA Tx Buffer Register */
+#define AST2600_I2CS_TX_DMA 0x38
+/* I2CS Target DMA Rx Buffer Register */
+#define AST2600_I2CS_RX_DMA 0x3C
+
+#define AST2600_I2CS_ADDR_CTRL 0x40
+
+#define AST2600_I2CS_ADDR3_MASK GENMASK(22, 16)
+#define AST2600_I2CS_ADDR2_MASK GENMASK(14, 8)
+#define AST2600_I2CS_ADDR1_MASK GENMASK(6, 0)
+
+#define AST2600_I2CM_DMA_LEN_STS 0x48
+#define AST2600_I2CS_DMA_LEN_STS 0x4C
+
+#define AST2600_I2C_GET_TX_DMA_LEN(x) ((x) & GENMASK(12, 0))
+#define AST2600_I2C_GET_RX_DMA_LEN(x) (((x) & GENMASK(28, 16)) >> 16)
+
+/* 0x40 : Target Device Address Register */
+#define AST2600_I2CS_ADDR3_ENABLE BIT(23)
+#define AST2600_I2CS_ADDR3(x) ((x) << 16)
+#define AST2600_I2CS_ADDR2_ENABLE BIT(15)
+#define AST2600_I2CS_ADDR2(x) ((x) << 8)
+#define AST2600_I2CS_ADDR1_ENABLE BIT(7)
+#define AST2600_I2CS_ADDR1(x) (x)
+
+#define CONTROLLER_TRIGGER_LAST_STOP (AST2600_I2CM_RX_CMD_LAST | AST2600_I2CM_STOP_CMD)
+#define TARGET_TRIGGER_CMD (AST2600_I2CS_ACTIVE_ALL | AST2600_I2CS_PKT_MODE_EN)
+
+#define AST_I2C_TIMEOUT_CLK 0x1
+
+struct ast2600_i2c_bus {
+ struct i2c_adapter adap;
+ struct device *dev;
+ void __iomem *reg_base;
+ struct regmap *global_regs;
+ struct clk *clk;
+ struct i2c_timings timing_info;
+ struct completion cmd_complete;
+ struct i2c_msg *msgs;
+ u32 apb_clk;
+ u32 timeout;
+ int irq;
+ int cmd_err;
+ int msgs_index;
+ int msgs_count;
+ int controller_xfer_cnt;
+ size_t buf_size;
+ bool multi_master;
+ void __iomem *buf_base;
+};
+
+static void ast2600_i2c_ac_timing_config(struct ast2600_i2c_bus *i2c_bus)
+{
+ unsigned long base_clk[16];
+ int baseclk_idx = 0;
+ int divisor = 0;
+ u32 clk_div_reg;
+ u32 scl_low;
+ u32 scl_high;
+ u32 data;
+
+ regmap_read(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, &clk_div_reg);
+
+ for (int i = 0; i < ARRAY_SIZE(base_clk); i++) {
+ if (i == 0)
+ base_clk[i] = i2c_bus->apb_clk;
+ else if (i < 5)
+ base_clk[i] = (i2c_bus->apb_clk * 2) /
+ (((clk_div_reg >> ((i - 1) * 8)) & GENMASK(7, 0)) + 2);
+ else
+ base_clk[i] = base_clk[4] >> (i - 4);
+
+ if ((base_clk[i] / i2c_bus->timing_info.bus_freq_hz) <= 32) {
+ baseclk_idx = i;
+ divisor = DIV_ROUND_UP(base_clk[i], i2c_bus->timing_info.bus_freq_hz);
+ break;
+ }
+ }
+ baseclk_idx = min(baseclk_idx, 15);
+ divisor = min(divisor, 32);
+ scl_low = min(divisor * 9 / 16 - 1, 15);
+ scl_high = (divisor - scl_low - 2) & GENMASK(3, 0);
+ data = (scl_high - 1) << 20 | scl_high << 16 | scl_low << 12 | baseclk_idx;
+ if (i2c_bus->timeout) {
+ data |= AST2600_I2CC_TOUTBASECLK(AST_I2C_TIMEOUT_CLK);
+ data |= AST2600_I2CC_TTIMEOUT(i2c_bus->timeout);
+ }
+
+ writel(data, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+}
+
+static int ast2600_i2c_recover_bus(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 state = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+ int ret = 0;
+ u32 ctrl;
+ int r;
+
+ dev_dbg(i2c_bus->dev, "%d-bus recovery bus [%x]\n", i2c_bus->adap.nr, state);
+
+ /* reset controller */
+ ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(ctrl & ~AST2600_I2CC_MASTER_EN, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ reinit_completion(&i2c_bus->cmd_complete);
+ i2c_bus->cmd_err = 0;
+
+ /* Check SDA/SCL status in the status register. */
+ state = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+ if (!(state & AST2600_I2CC_SDA_LINE_STS) && (state & AST2600_I2CC_SCL_LINE_STS)) {
+ writel(AST2600_I2CM_RECOVER_CMD_EN, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+ r = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
+ if (r == 0) {
+ dev_dbg(i2c_bus->dev, "recovery timed out\n");
+ return -ETIMEDOUT;
+ } else if (i2c_bus->cmd_err) {
+ dev_dbg(i2c_bus->dev, "recovery error\n");
+ ret = -EPROTO;
+ }
+ }
+
+ /* Recovery done */
+ state = readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF);
+ if (state & AST2600_I2CC_BUS_BUSY_STS) {
+ dev_dbg(i2c_bus->dev, "Can't recover bus [%x]\n", state);
+ ret = -EPROTO;
+ }
+
+ return ret;
+}
+
+static int ast2600_i2c_setup_buff_tx(u32 cmd, struct ast2600_i2c_bus *i2c_bus)
+{
+ struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+ int xfer_len = msg->len - i2c_bus->controller_xfer_cnt;
+ u32 wbuf_dword;
+ int i;
+
+ cmd |= AST2600_I2CM_PKT_EN;
+
+ if (xfer_len > i2c_bus->buf_size)
+ xfer_len = i2c_bus->buf_size;
+ else if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count)
+ cmd |= AST2600_I2CM_STOP_CMD;
+
+ if (cmd & AST2600_I2CM_START_CMD)
+ cmd |= AST2600_I2CM_PKT_ADDR(msg->addr);
+
+ if (xfer_len) {
+ cmd |= AST2600_I2CM_TX_BUFF_EN | AST2600_I2CM_TX_CMD;
+ /*
+ * The controller's buffer register supports dword writes only.
+ * Therefore, write dwords to the buffer register in a 4-byte aligned,
+ * and write the remaining unaligned data at the end.
+ */
+ for (i = 0; i < xfer_len; i += 4) {
+ int xfer_cnt = i2c_bus->controller_xfer_cnt + i;
+
+ switch (min(xfer_len - i, 4) % 4) {
+ case 1:
+ wbuf_dword = msg->buf[xfer_cnt];
+ break;
+ case 2:
+ wbuf_dword = get_unaligned_le16(&msg->buf[xfer_cnt]);
+ break;
+ case 3:
+ wbuf_dword = get_unaligned_le24(&msg->buf[xfer_cnt]);
+ break;
+ default:
+ wbuf_dword = get_unaligned_le32(&msg->buf[xfer_cnt]);
+ break;
+ }
+ writel(wbuf_dword, i2c_bus->buf_base + i);
+ }
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(xfer_len),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ }
+
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+
+ return 0;
+}
+
+static int ast2600_i2c_setup_buff_rx(u32 cmd, struct ast2600_i2c_bus *i2c_bus)
+{
+ struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+ int xfer_len = msg->len - i2c_bus->controller_xfer_cnt;
+
+ cmd |= AST2600_I2CM_PKT_EN | AST2600_I2CM_RX_BUFF_EN | AST2600_I2CM_RX_CMD;
+
+ if (cmd & AST2600_I2CM_START_CMD)
+ cmd |= AST2600_I2CM_PKT_ADDR(msg->addr);
+
+ if (msg->flags & I2C_M_RECV_LEN) {
+ dev_dbg(i2c_bus->dev, "smbus read\n");
+ xfer_len = 1;
+ } else if (xfer_len > i2c_bus->buf_size) {
+ xfer_len = i2c_bus->buf_size;
+ } else if (i2c_bus->msgs_index + 1 == i2c_bus->msgs_count) {
+ cmd |= CONTROLLER_TRIGGER_LAST_STOP;
+ }
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(xfer_len), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+
+ return 0;
+}
+
+static int ast2600_i2c_do_start(struct ast2600_i2c_bus *i2c_bus)
+{
+ struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+
+ /* send start */
+ dev_dbg(i2c_bus->dev, "[%d] %s %d byte%s %s 0x%02x\n",
+ i2c_bus->msgs_index, str_read_write(msg->flags & I2C_M_RD),
+ msg->len, str_plural(msg->len),
+ msg->flags & I2C_M_RD ? "from" : "to", msg->addr);
+
+ i2c_bus->controller_xfer_cnt = 0;
+
+ if (msg->flags & I2C_M_RD)
+ return ast2600_i2c_setup_buff_rx(AST2600_I2CM_START_CMD, i2c_bus);
+
+ return ast2600_i2c_setup_buff_tx(AST2600_I2CM_START_CMD, i2c_bus);
+}
+
+static int ast2600_i2c_irq_err_to_errno(u32 irq_status)
+{
+ if (irq_status & AST2600_I2CM_ARBIT_LOSS)
+ return -EAGAIN;
+ if (irq_status & (AST2600_I2CM_SDA_DL_TO | AST2600_I2CM_SCL_LOW_TO))
+ return -ETIMEDOUT;
+ if (irq_status & (AST2600_I2CM_ABNORMAL))
+ return -EPROTO;
+
+ return 0;
+}
+
+static void ast2600_i2c_controller_packet_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+ struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
+ int xfer_len;
+ int i;
+
+ sts &= ~AST2600_I2CM_PKT_DONE;
+ writel(AST2600_I2CM_PKT_DONE, i2c_bus->reg_base + AST2600_I2CM_ISR);
+ switch (sts) {
+ case AST2600_I2CM_PKT_ERROR:
+ i2c_bus->cmd_err = -EAGAIN;
+ complete(&i2c_bus->cmd_complete);
+ break;
+ case AST2600_I2CM_PKT_ERROR | AST2600_I2CM_TX_NAK: /* a0 fix for issue */
+ fallthrough;
+ case AST2600_I2CM_PKT_ERROR | AST2600_I2CM_TX_NAK | AST2600_I2CM_NORMAL_STOP:
+ i2c_bus->cmd_err = -ENXIO;
+ complete(&i2c_bus->cmd_complete);
+ break;
+ case AST2600_I2CM_NORMAL_STOP:
+ /* write 0 byte only have stop isr */
+ i2c_bus->msgs_index++;
+ if (i2c_bus->msgs_index < i2c_bus->msgs_count) {
+ if (ast2600_i2c_do_start(i2c_bus)) {
+ i2c_bus->cmd_err = -ENOMEM;
+ complete(&i2c_bus->cmd_complete);
+ }
+ } else {
+ i2c_bus->cmd_err = i2c_bus->msgs_index;
+ complete(&i2c_bus->cmd_complete);
+ }
+ break;
+ case AST2600_I2CM_TX_ACK:
+ case AST2600_I2CM_TX_ACK | AST2600_I2CM_NORMAL_STOP:
+ xfer_len = AST2600_I2CC_GET_TX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ i2c_bus->controller_xfer_cnt += xfer_len;
+
+ if (i2c_bus->controller_xfer_cnt == msg->len) {
+ i2c_bus->msgs_index++;
+ if (i2c_bus->msgs_index == i2c_bus->msgs_count) {
+ i2c_bus->cmd_err = i2c_bus->msgs_index;
+ complete(&i2c_bus->cmd_complete);
+ } else {
+ if (ast2600_i2c_do_start(i2c_bus)) {
+ i2c_bus->cmd_err = -ENOMEM;
+ complete(&i2c_bus->cmd_complete);
+ }
+ }
+ } else {
+ ast2600_i2c_setup_buff_tx(0, i2c_bus);
+ }
+ break;
+ case AST2600_I2CM_RX_DONE:
+ case AST2600_I2CM_RX_DONE | AST2600_I2CM_NORMAL_STOP:
+ /* do next rx */
+ xfer_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < xfer_len; i++)
+ msg->buf[i2c_bus->controller_xfer_cnt + i] =
+ readb(i2c_bus->buf_base + 0x10 + i);
+
+ if (msg->flags & I2C_M_RECV_LEN) {
+ u8 recv_len = AST2600_I2CC_GET_RX_BUFF(readl(i2c_bus->reg_base
+ + AST2600_I2CC_STS_AND_BUFF));
+ msg->len = min_t(unsigned int, recv_len, I2C_SMBUS_BLOCK_MAX);
+ msg->len += ((msg->flags & I2C_CLIENT_PEC) ? 2 : 1);
+ msg->flags &= ~I2C_M_RECV_LEN;
+ if (!recv_len)
+ i2c_bus->controller_xfer_cnt = 0;
+ else
+ i2c_bus->controller_xfer_cnt = 1;
+ } else {
+ i2c_bus->controller_xfer_cnt += xfer_len;
+ }
+
+ if (i2c_bus->controller_xfer_cnt == msg->len) {
+ i2c_bus->msgs_index++;
+ if (i2c_bus->msgs_index == i2c_bus->msgs_count) {
+ i2c_bus->cmd_err = i2c_bus->msgs_index;
+ complete(&i2c_bus->cmd_complete);
+ } else {
+ if (ast2600_i2c_do_start(i2c_bus)) {
+ i2c_bus->cmd_err = -ENOMEM;
+ complete(&i2c_bus->cmd_complete);
+ }
+ }
+ } else {
+ ast2600_i2c_setup_buff_rx(0, i2c_bus);
+ }
+ break;
+ default:
+ dev_dbg(i2c_bus->dev, "unhandled sts %x\n", sts);
+ break;
+ }
+}
+
+static int ast2600_i2c_controller_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 sts = readl(i2c_bus->reg_base + AST2600_I2CM_ISR);
+ u32 ctrl;
+
+ sts &= ~AST2600_I2CM_SMBUS_ALERT;
+
+ if (sts & AST2600_I2CM_BUS_RECOVER_FAIL) {
+ writel(AST2600_I2CM_BUS_RECOVER_FAIL, i2c_bus->reg_base + AST2600_I2CM_ISR);
+ ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ i2c_bus->cmd_err = -EPROTO;
+ complete(&i2c_bus->cmd_complete);
+ return 1;
+ }
+
+ if (sts & AST2600_I2CM_BUS_RECOVER) {
+ writel(AST2600_I2CM_BUS_RECOVER, i2c_bus->reg_base + AST2600_I2CM_ISR);
+ i2c_bus->cmd_err = 0;
+ complete(&i2c_bus->cmd_complete);
+ return 1;
+ }
+
+ i2c_bus->cmd_err = ast2600_i2c_irq_err_to_errno(sts);
+ if (i2c_bus->cmd_err) {
+ writel(AST2600_I2CM_PKT_DONE, i2c_bus->reg_base + AST2600_I2CM_ISR);
+ complete(&i2c_bus->cmd_complete);
+ return 1;
+ }
+
+ if (sts & AST2600_I2CM_PKT_DONE) {
+ ast2600_i2c_controller_packet_irq(i2c_bus, sts);
+ return 1;
+ }
+
+ return 0;
+}
+
+static irqreturn_t ast2600_i2c_bus_irq(int irq, void *dev_id)
+{
+ struct ast2600_i2c_bus *i2c_bus = dev_id;
+
+ return IRQ_RETVAL(ast2600_i2c_controller_irq(i2c_bus));
+}
+
+static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(adap);
+ unsigned long timeout;
+ int ret;
+
+ if (!i2c_bus->multi_master &&
+ (readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) & AST2600_I2CC_BUS_BUSY_STS)) {
+ ret = ast2600_i2c_recover_bus(i2c_bus);
+ if (ret)
+ return ret;
+ }
+
+ i2c_bus->cmd_err = 0;
+ i2c_bus->msgs = msgs;
+ i2c_bus->msgs_index = 0;
+ i2c_bus->msgs_count = num;
+ reinit_completion(&i2c_bus->cmd_complete);
+ ret = ast2600_i2c_do_start(i2c_bus);
+ if (ret)
+ goto controller_out;
+ timeout = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
+ if (timeout == 0) {
+ u32 ctrl = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ dev_dbg(i2c_bus->dev, "timeout isr[%x], sts[%x]\n",
+ readl(i2c_bus->reg_base + AST2600_I2CM_ISR),
+ readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+ writel(ctrl & ~AST2600_I2CC_MASTER_EN, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ /*
+ * A slave holding SCL low can stall the transfer and trigger
+ * a master timeout. In multi-master mode, attempt bus recovery
+ * if the bus is still busy.
+ */
+ if (i2c_bus->multi_master &&
+ (readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) &
+ AST2600_I2CC_BUS_BUSY_STS))
+ ast2600_i2c_recover_bus(i2c_bus);
+ ret = -ETIMEDOUT;
+ } else {
+ ret = i2c_bus->cmd_err;
+ }
+
+ dev_dbg(i2c_bus->dev, "bus%d-m: %d end\n", i2c_bus->adap.nr, i2c_bus->cmd_err);
+
+controller_out:
+ return ret;
+}
+
+static int ast2600_i2c_init(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 fun_ctrl = AST2600_I2CC_BUS_AUTO_RELEASE | AST2600_I2CC_MASTER_EN;
+
+ /* I2C Reset */
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ if (!i2c_bus->multi_master)
+ fun_ctrl |= AST2600_I2CC_MULTI_MASTER_DIS;
+
+ /* Enable Controller Mode */
+ writel(fun_ctrl, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ /* disable target address */
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ /* Set AC Timing */
+ ast2600_i2c_ac_timing_config(i2c_bus);
+
+ /* Clear Interrupt */
+ writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CM_ISR);
+
+ return 0;
+}
+
+static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA;
+}
+
+static const struct i2c_algorithm i2c_ast2600_algorithm = {
+ .xfer = ast2600_i2c_controller_xfer,
+ .functionality = ast2600_i2c_functionality,
+};
+
+static int ast2600_i2c_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ast2600_i2c_bus *i2c_bus;
+ void __iomem *buf_base;
+ struct reset_control *rst;
+ struct resource *res;
+ u32 global_ctrl;
+ int ret;
+
+ if (!device_property_present(dev, "aspeed,global-regs"))
+ return -ENODEV;
+
+ i2c_bus = devm_kzalloc(dev, sizeof(*i2c_bus), GFP_KERNEL);
+ if (!i2c_bus)
+ return -ENOMEM;
+
+ i2c_bus->reg_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(i2c_bus->reg_base))
+ return PTR_ERR(i2c_bus->reg_base);
+
+ rst = devm_reset_control_get_shared_deasserted(dev, NULL);
+ if (IS_ERR(rst))
+ return dev_err_probe(dev, PTR_ERR(rst), "Missing reset ctrl\n");
+
+ i2c_bus->global_regs =
+ syscon_regmap_lookup_by_phandle(dev_of_node(dev), "aspeed,global-regs");
+ if (IS_ERR(i2c_bus->global_regs))
+ return PTR_ERR(i2c_bus->global_regs);
+
+ regmap_read(i2c_bus->global_regs, AST2600_I2CG_CTRL, &global_ctrl);
+ if ((global_ctrl & AST2600_GLOBAL_INIT) != AST2600_GLOBAL_INIT) {
+ regmap_write(i2c_bus->global_regs, AST2600_I2CG_CTRL, AST2600_GLOBAL_INIT);
+ regmap_write(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, I2CCG_DIV_CTRL);
+ }
+
+ i2c_bus->dev = dev;
+ i2c_bus->multi_master = device_property_read_bool(dev, "multi-master");
+
+ buf_base = devm_platform_get_and_ioremap_resource(pdev, 1, &res);
+ if (IS_ERR(buf_base))
+ return dev_err_probe(dev, PTR_ERR(buf_base), "Missing buffer resource\n");
+ i2c_bus->buf_base = buf_base;
+ i2c_bus->buf_size = resource_size(res) / 2;
+
+ /*
+ * i2c timeout counter: use base clk4 1Mhz,
+ * per unit: 1/(1000/1024) = 1024us
+ */
+ ret = device_property_read_u32(dev, "i2c-scl-clk-low-timeout-us", &i2c_bus->timeout);
+ if (!ret)
+ i2c_bus->timeout = DIV_ROUND_UP(i2c_bus->timeout, 1024);
+
+ init_completion(&i2c_bus->cmd_complete);
+
+ i2c_bus->irq = platform_get_irq(pdev, 0);
+ if (i2c_bus->irq < 0)
+ return i2c_bus->irq;
+
+ platform_set_drvdata(pdev, i2c_bus);
+
+ i2c_bus->clk = devm_clk_get(i2c_bus->dev, NULL);
+ if (IS_ERR(i2c_bus->clk))
+ return dev_err_probe(i2c_bus->dev, PTR_ERR(i2c_bus->clk), "Can't get clock\n");
+
+ i2c_bus->apb_clk = clk_get_rate(i2c_bus->clk);
+
+ i2c_parse_fw_timings(i2c_bus->dev, &i2c_bus->timing_info, true);
+
+ /* Initialize the I2C adapter */
+ i2c_bus->adap.owner = THIS_MODULE;
+ i2c_bus->adap.algo = &i2c_ast2600_algorithm;
+ i2c_bus->adap.retries = 0;
+ i2c_bus->adap.dev.parent = i2c_bus->dev;
+ device_set_node(&i2c_bus->adap.dev, dev_fwnode(dev));
+ i2c_bus->adap.algo_data = i2c_bus;
+ strscpy(i2c_bus->adap.name, pdev->name);
+ i2c_set_adapdata(&i2c_bus->adap, i2c_bus);
+
+ ret = ast2600_i2c_init(i2c_bus);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "Unable to initialize i2c %d\n", ret);
+
+ ret = devm_request_irq(dev, i2c_bus->irq, ast2600_i2c_bus_irq, 0,
+ dev_name(dev), i2c_bus);
+ if (ret < 0) {
+ ret = dev_err_probe(dev, ret, "Unable to request irq %d\n",
+ i2c_bus->irq);
+ goto err;
+ }
+
+ writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
+ i2c_bus->reg_base + AST2600_I2CM_IER);
+
+ ret = devm_i2c_add_adapter(dev, &i2c_bus->adap);
+ if (ret)
+ goto err;
+
+ return 0;
+
+err:
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_IER);
+ return ret;
+}
+
+static void ast2600_i2c_remove(struct platform_device *pdev)
+{
+ struct ast2600_i2c_bus *i2c_bus = platform_get_drvdata(pdev);
+
+ /* Disable everything. */
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_IER);
+}
+
+static const struct of_device_id ast2600_i2c_of_match[] = {
+ { .compatible = "aspeed,ast2600-i2c-bus" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ast2600_i2c_of_match);
+
+static struct platform_driver ast2600_i2c_driver = {
+ .probe = ast2600_i2c_probe,
+ .remove = ast2600_i2c_remove,
+ .driver = {
+ .name = "ast2600-i2c",
+ .of_match_table = ast2600_i2c_of_match,
+ },
+};
+module_platform_driver(ast2600_i2c_driver);
+
+MODULE_AUTHOR("Ryan Chen <ryan_chen@aspeedtech.com>");
+MODULE_DESCRIPTION("ASPEED AST2600 I2C Controller Driver");
+MODULE_LICENSE("GPL");
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH v29 4/4] i2c: ast2600: Add target mode support
2026-04-15 5:14 [PATCH v29 0/4] Add ASPEED AST2600 I2C controller driver Ryan Chen
` (2 preceding siblings ...)
2026-04-15 5:14 ` [PATCH v29 3/4] i2c: ast2600: Add controller driver for AST2600 new register set Ryan Chen
@ 2026-04-15 5:14 ` Ryan Chen
3 siblings, 0 replies; 7+ messages in thread
From: Ryan Chen @ 2026-04-15 5:14 UTC (permalink / raw)
To: jk, andriy.shevchenko, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Joel Stanley, Andrew Jeffery,
Benjamin Herrenschmidt, Rayn Chen, Philipp Zabel
Cc: linux-i2c, devicetree, linux-arm-kernel, linux-aspeed,
linux-kernel, openbmc, Ryan Chen
Add target mode support to the AST2600 I2C driver.
Target mode features implemented include:
- Add target interrupt handling
- Address match and response logic
This complements the existing controller-mode support, enabling
dual-role capability.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
---
Changes in v29:
- fix race between unreg_target and IRQ handler.
- move i2cs ier enable from ast2600_i2c_init to probe after master ier enable.
- remove dma/byte transfer, use buffer mode only.
Changes in v28:
- fix typo condication -> condition
- fix compile error, when disable CONFIG_I2C_SLAVE
Changes in v26:
- change int to bool target_operate
- rename target_operate to target_active
- use i2c_bus->target replace require IO
- use WRITE_ONCE replace target_operate write.
---
drivers/i2c/busses/i2c-ast2600.c | 340 +++++++++++++++++++++++++++++++++++++++
1 file changed, 340 insertions(+)
diff --git a/drivers/i2c/busses/i2c-ast2600.c b/drivers/i2c/busses/i2c-ast2600.c
index 787ef6bd6244..137aaf7e26b5 100644
--- a/drivers/i2c/busses/i2c-ast2600.c
+++ b/drivers/i2c/busses/i2c-ast2600.c
@@ -254,6 +254,11 @@ struct ast2600_i2c_bus {
size_t buf_size;
bool multi_master;
void __iomem *buf_base;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* target structure */
+ bool target_active;
+ struct i2c_client *target;
+#endif
};
static void ast2600_i2c_ac_timing_config(struct ast2600_i2c_bus *i2c_bus)
@@ -337,6 +342,243 @@ static int ast2600_i2c_recover_bus(struct ast2600_i2c_bus *i2c_bus)
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static void ast2600_i2c_target_packet_buff_irq(struct ast2600_i2c_bus *i2c_bus, u32 sts)
+{
+ int target_rx_len = 0;
+ u32 cmd = 0;
+ u8 value;
+ int i;
+
+ /* due to controller target is common buffer, need force the master stop not issue */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_CMD_STS) & GENMASK(15, 0)) {
+ writel(0, i2c_bus->reg_base + AST2600_I2CM_CMD_STS);
+ i2c_bus->cmd_err = -EBUSY;
+ writel(0, i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ complete(&i2c_bus->cmd_complete);
+ }
+
+ /* Handle i2c target timeout condition */
+ if (AST2600_I2CS_INACTIVE_TO & sts) {
+ /* Reset timeout counter */
+ u32 ac_timing = readl(i2c_bus->reg_base + AST2600_I2CC_AC_TIMING) &
+ AST2600_I2CC_AC_TIMING_MASK;
+
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ ac_timing |= AST2600_I2CC_TTIMEOUT(i2c_bus->timeout);
+ writel(ac_timing, i2c_bus->reg_base + AST2600_I2CC_AC_TIMING);
+ writel(TARGET_TRIGGER_CMD, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ WRITE_ONCE(i2c_bus->target_active, false);
+ return;
+ }
+
+ sts &= ~(AST2600_I2CS_PKT_DONE | AST2600_I2CS_PKT_ERROR);
+
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ WRITE_ONCE(i2c_bus->target_active, true);
+
+ switch (sts) {
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_STOP:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ fallthrough;
+ case AST2600_I2CS_SLAVE_PENDING |
+ AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD;
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ }
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_RX_BUFF_EN)
+ cmd = 0;
+ else
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_RX_DONE:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA |
+ AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ cmd |= AST2600_I2CS_RX_BUFF_EN;
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_RX_DONE | AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ /* workaround for avoid next start with len != 0 */
+ writel(BIT(0), i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_RX_DONE |
+ AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_STOP:
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writeb(value, i2c_bus->buf_base);
+ break;
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_SLAVE_MATCH:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ writeb(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_SLAVE_PENDING | AST2600_I2CS_WAIT_RX_DMA | AST2600_I2CS_STOP |
+ AST2600_I2CS_TX_NAK | AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ writel(AST2600_I2CC_SET_RX_BUF_LEN(i2c_bus->buf_size),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ break;
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA | AST2600_I2CS_RX_DONE:
+ case AST2600_I2CS_WAIT_TX_DMA:
+ if (sts & AST2600_I2CS_SLAVE_MATCH)
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+
+ if (sts & AST2600_I2CS_RX_DONE) {
+ target_rx_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
+ AST2600_I2CC_BUFF_CTRL));
+ for (i = 0; i < target_rx_len; i++) {
+ value = readb(i2c_bus->buf_base + 0x10 + i);
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_RECEIVED, &value);
+ }
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_REQUESTED, &value);
+ } else {
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_READ_PROCESSED, &value);
+ }
+ writeb(value, i2c_bus->buf_base);
+ writel(AST2600_I2CC_SET_TX_BUF_LEN(1),
+ i2c_bus->reg_base + AST2600_I2CC_BUFF_CTRL);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_TX_BUFF_EN;
+ break;
+ /* workaround : trigger the cmd twice to fix next state keep 1000000 */
+ case AST2600_I2CS_SLAVE_MATCH | AST2600_I2CS_RX_DONE:
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_WRITE_REQUESTED, &value);
+ cmd = TARGET_TRIGGER_CMD | AST2600_I2CS_RX_BUFF_EN;
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ break;
+ case AST2600_I2CS_TX_NAK | AST2600_I2CS_STOP:
+ case AST2600_I2CS_STOP:
+ cmd = TARGET_TRIGGER_CMD;
+ i2c_slave_event(i2c_bus->target, I2C_SLAVE_STOP, &value);
+ break;
+ default:
+ dev_dbg(i2c_bus->dev, "unhandled target isr case %x, sts %x\n", sts,
+ readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF));
+ break;
+ }
+
+ if (cmd)
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_ISR);
+ readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if ((sts & AST2600_I2CS_STOP) && !(sts & AST2600_I2CS_SLAVE_PENDING))
+ WRITE_ONCE(i2c_bus->target_active, false);
+}
+
+static int ast2600_i2c_target_irq(struct ast2600_i2c_bus *i2c_bus)
+{
+ u32 ier = readl(i2c_bus->reg_base + AST2600_I2CS_IER);
+ u32 isr = readl(i2c_bus->reg_base + AST2600_I2CS_ISR);
+
+ if (!(isr & ier))
+ return 0;
+
+ /*
+ * Target interrupt coming after controller packet done
+ * So need handle controller first.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CM_ISR) & AST2600_I2CM_PKT_DONE)
+ return 0;
+
+ isr &= ~(AST2600_I2CS_ADDR_INDICATE_MASK);
+
+ if (AST2600_I2CS_ADDR1_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR1_NAK;
+
+ if (AST2600_I2CS_ADDR2_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR2_NAK;
+
+ if (AST2600_I2CS_ADDR3_NAK & isr)
+ isr &= ~AST2600_I2CS_ADDR3_NAK;
+
+ if (AST2600_I2CS_ADDR_MASK & isr)
+ isr &= ~AST2600_I2CS_ADDR_MASK;
+
+ if (AST2600_I2CS_PKT_DONE & isr)
+ ast2600_i2c_target_packet_buff_irq(i2c_bus, isr);
+
+ return 1;
+}
+#endif
+
static int ast2600_i2c_setup_buff_tx(u32 cmd, struct ast2600_i2c_bus *i2c_bus)
{
struct i2c_msg *msg = &i2c_bus->msgs[i2c_bus->msgs_index];
@@ -498,6 +740,20 @@ static void ast2600_i2c_controller_packet_irq(struct ast2600_i2c_bus *i2c_bus, u
}
break;
case AST2600_I2CM_RX_DONE:
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /*
+ * Workaround for controller/target packet mode enable rx done stuck issue
+ * When controller go for first read (RX_DONE), target mode will also effect
+ * Then controller will send nack, not operate anymore.
+ */
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS) & AST2600_I2CS_PKT_MODE_EN) {
+ u32 target_cmd = readl(i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ writel(target_cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ }
+ fallthrough;
+#endif
case AST2600_I2CM_RX_DONE | AST2600_I2CM_NORMAL_STOP:
/* do next rx */
xfer_len = AST2600_I2CC_GET_RX_BUF_LEN(readl(i2c_bus->reg_base +
@@ -584,6 +840,12 @@ static irqreturn_t ast2600_i2c_bus_irq(int irq, void *dev_id)
{
struct ast2600_i2c_bus *i2c_bus = dev_id;
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target) {
+ if (ast2600_i2c_target_irq(i2c_bus))
+ return IRQ_HANDLED;
+ }
+#endif
return IRQ_RETVAL(ast2600_i2c_controller_irq(i2c_bus));
}
@@ -600,12 +862,31 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
return ret;
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ if (i2c_bus->target_active)
+ return -EBUSY;
+ /*
+ * Controller and target share the same buffer register. A target
+ * transaction can update buffer state asynchronously via IRQ, so block
+ * controller transfers while target is active to avoid buffer corruption.
+ */
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_IER);
+ if (readl(i2c_bus->reg_base + AST2600_I2CS_ISR) || i2c_bus->target_active) {
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+ return -EBUSY;
+ }
+#endif
+
i2c_bus->cmd_err = 0;
i2c_bus->msgs = msgs;
i2c_bus->msgs_index = 0;
i2c_bus->msgs_count = num;
reinit_completion(&i2c_bus->cmd_complete);
ret = ast2600_i2c_do_start(i2c_bus);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ /* avoid race condition target is wait and controller wait 1st target operate */
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
if (ret)
goto controller_out;
timeout = wait_for_completion_timeout(&i2c_bus->cmd_complete, i2c_bus->adap.timeout);
@@ -624,6 +905,9 @@ static int ast2600_i2c_controller_xfer(struct i2c_adapter *adap, struct i2c_msg
* if the bus is still busy.
*/
if (i2c_bus->multi_master &&
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ !i2c_bus->target_active &&
+#endif
(readl(i2c_bus->reg_base + AST2600_I2CC_STS_AND_BUFF) &
AST2600_I2CC_BUS_BUSY_STS))
ast2600_i2c_recover_bus(i2c_bus);
@@ -659,8 +943,54 @@ static int ast2600_i2c_init(struct ast2600_i2c_bus *i2c_bus)
/* Clear Interrupt */
writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CM_ISR);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(GENMASK(27, 0), i2c_bus->reg_base + AST2600_I2CS_ISR);
+#endif
+
+ return 0;
+}
+
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+static int ast2600_i2c_reg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 cmd = TARGET_TRIGGER_CMD;
+
+ if (i2c_bus->target)
+ return -EINVAL;
+
+ dev_dbg(i2c_bus->dev, "target addr %x\n", client->addr);
+
+ writel(0, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+ writel(AST2600_I2CC_SLAVE_EN | readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL),
+ i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+
+ writel(cmd, i2c_bus->reg_base + AST2600_I2CS_CMD_STS);
+ i2c_bus->target = client;
+ /* Set target addr. */
+ writel(client->addr | AST2600_I2CS_ADDR1_ENABLE,
+ i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ return 0;
+}
+
+static int ast2600_i2c_unreg_target(struct i2c_client *client)
+{
+ struct ast2600_i2c_bus *i2c_bus = i2c_get_adapdata(client->adapter);
+ u32 val;
+
+ /* Turn off target mode. */
+ val = readl(i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ writel(val & ~AST2600_I2CC_SLAVE_EN, i2c_bus->reg_base + AST2600_I2CC_FUN_CTRL);
+ val = readl(i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+ writel(val & ~AST2600_I2CS_ADDR1_MASK, i2c_bus->reg_base + AST2600_I2CS_ADDR_CTRL);
+
+ synchronize_irq(i2c_bus->irq);
+ i2c_bus->target = NULL;
+
return 0;
}
+#endif
static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
{
@@ -670,6 +1000,10 @@ static u32 ast2600_i2c_functionality(struct i2c_adapter *adap)
static const struct i2c_algorithm i2c_ast2600_algorithm = {
.xfer = ast2600_i2c_controller_xfer,
.functionality = ast2600_i2c_functionality,
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ .reg_target = ast2600_i2c_reg_target,
+ .unreg_target = ast2600_i2c_unreg_target,
+#endif
};
static int ast2600_i2c_probe(struct platform_device *pdev)
@@ -708,6 +1042,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
regmap_write(i2c_bus->global_regs, AST2600_I2CG_CLK_DIV_CTRL, I2CCG_DIV_CTRL);
}
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ WRITE_ONCE(i2c_bus->target_active, false);
+#endif
i2c_bus->dev = dev;
i2c_bus->multi_master = device_property_read_bool(dev, "multi-master");
@@ -765,6 +1102,9 @@ static int ast2600_i2c_probe(struct platform_device *pdev)
writel(AST2600_I2CM_PKT_DONE | AST2600_I2CM_BUS_RECOVER,
i2c_bus->reg_base + AST2600_I2CM_IER);
+#if IS_ENABLED(CONFIG_I2C_SLAVE)
+ writel(AST2600_I2CS_PKT_DONE, i2c_bus->reg_base + AST2600_I2CS_IER);
+#endif
ret = devm_i2c_add_adapter(dev, &i2c_bus->adap);
if (ret)
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread