* [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili
@ 2026-10-30 12:43 Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 1/5] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible Nihal Kumar Gupta
` (4 more replies)
0 siblings, 5 replies; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media,
Krzysztof Kozlowski
Hawi and Maili are recently announced Qualcomm Snapdragon SoCs [1].
This series adds Camera Subsystem (CAMSS) support for the Qualcomm
Hawi and Maili SoC's.
[1] https://www.qualcomm.com/smartphones/products/8-series/snapdragon-8-elite-gen-6-mobile-platform
Hawi's camera hardware topology:
- 6x CSIPHY (CSI Physical Layer)
- 3x TPG (Test Pattern Generator)
- 3x CSID (CSI Decoder)
- 2x CSID Lite
- 3x VFE (Video Front End), 5 RDI per VFE
- 2x VFE Lite, 4 RDI per VFE Lite
Maili shares the same IP as Hawi. The only difference is Hawi has 6 CSIPHY
while Maili has 5.
Used following tools for the sanity check of these changes.
- make -j32 W=1
- checkpatch.pl
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml dt_binding_check
- make DT_CHECKER_FLAGS=-m DT_SCHEMA_FILES=media/qcom,hawi-camss.yaml dt_binding_check W=1
- make CHECK_DTBS=y W=1 dtbs
Dependencies
------------
[1] https://lore.kernel.org/all/20261028-kaanapali-camss-v23-0-95f250b18612@oss.qualcomm.com/ -- Kaanapali CAMSS driver and bindings
Patch grouping
------------
I2C CCI bindings part for maintainer Loic/Robert/Andi (1):
[1] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible
PHY driver part for maintainer Vinod Koul (2):
[2] dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles
[4] phy: qcom-mipi-csi2: Add Hawi support
CAMSS driver and DTS part for maintainer Bryan O'Donoghue (5):
[3] dt-bindings: media: Add CAMSS device for Hawi and Maili
[5] media: qcom: camss: Add support for Hawi
---
Changes in v3:
- Rebase on next-20261029
- Squash Hawi and Maili CAMSS binding as a whole - Krzysztof
- Add description for IFE and IFE_LITE IOMMU in CAMSS binding - bod
- Correct the lane count variable fallback path - Sashiko
- Add CAMSS top region to binding and DT - Loic
- Use split addr_update/reg_update in CSID and VFE 1190 - Loic/bod
- Add SOF and EOF enable bits with top level RDI status offset to
allow their corresponding interrupts but not configured on - bod
- Move the common CPAS/GCC AHB and AXI clocks to the pm_clks array
drop them from the VFE clock lists - Loic
- Use the GPIO function with bias disabled for CCI sleep states - Loic
- Collect RBs from Loic, Krzysztof and bod
- Link to v2: https://lore.kernel.org/r/20261013-hawi-maili-camss-v2-0-fc93222da89c@oss.qualcomm.com
Changes in v2:
- Not an RFC anymore
- Rebase on next-20261012 and drop the external CSI2 PHY series dependency.
- Drop DTS patches; they will be posted separately with Maili DTS dependency.
- Collect Reviewed-by from Konrad, Abel, Bryan
- Split CSID and VFE 1190 into individual files rather than in separate
combined Gen4 files - bod
- Remove reduandant is_lite condition in CAMSS CSID and VFE resources - bod
- Replace bias-pull-up and bias-pull-down with bias-disable for the
SCL/SDA pins of CCI nodes in TLMM, as internal weak pull is inproper
with existing board level pull up resistors - Loic
- Drop the unused reg_update_after_csid_config flag
- Add lane count fallback path for CSID RX configuration
- Add Hawi DPHY support by tuning register table, which prevents
potential stream stalls and SMMU faults.
- Add a standalone Hawi CSI2 PHY compatible and make Maili fall back to it.
- Resolve conflicts introduced by Glymur in CSI2 PHY binding.
- Link to v1: https://lore.kernel.org/r/20260923-hawi-maili-camss-v1-0-cbbb42e534ef@oss.qualcomm.com
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
Hangxiang Ma (4):
dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible
dt-bindings: media: Add CAMSS device for Hawi and Maili
phy: qcom-mipi-csi2: Add Hawi support
media: qcom: camss: Add support for Hawi
Nihal Kumar Gupta (1):
dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles
.../devicetree/bindings/i2c/qcom,i2c-cci.yaml | 2 +
.../devicetree/bindings/media/qcom,hawi-camss.yaml | 314 ++++++++++++++++
.../bindings/phy/qcom,x1e80100-csi2-phy.yaml | 5 +
drivers/media/platform/qcom/camss/Makefile | 2 +
.../media/platform/qcom/camss/camss-csid-1190.c | 417 +++++++++++++++++++++
drivers/media/platform/qcom/camss/camss-csid.h | 1 +
drivers/media/platform/qcom/camss/camss-vfe-1190.c | 217 +++++++++++
drivers/media/platform/qcom/camss/camss-vfe.c | 2 +
drivers/media/platform/qcom/camss/camss-vfe.h | 1 +
drivers/media/platform/qcom/camss/camss.c | 229 +++++++++++
drivers/media/platform/qcom/camss/camss.h | 1 +
drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c | 136 +++++++
drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c | 1 +
drivers/phy/qualcomm/phy-qcom-mipi-csi2.h | 1 +
14 files changed, 1329 insertions(+)
---
base-commit: a39c950806213f6861d00f90729acaaa21f2d95a
change-id: 20260923-hawi-maili-camss-b5dc43a00ed2
prerequisite-patch-id: 6108fea87bf95e2911f09bbe7e95fa536c3ce397
prerequisite-patch-id: b347ad60c475f3035b04ec76741e0f1b5f095580
prerequisite-patch-id: aa51e15c5698d3425e979c810ff54968178a364b
prerequisite-patch-id: 5faef8cef855ce6fa00e2c7f10f125431ede40a4
prerequisite-patch-id: ae577f411cccd0e6cdfcfd05ea6cbfc3e87eca37
prerequisite-patch-id: 56eff00251984e6b3da63327eec1efcdb8194ef1
prerequisite-patch-id: 768be92ac0d44493176dfdcaddd24256719a3761
prerequisite-patch-id: 9908a408d5259107a6f00780d7147cddb625b02d
prerequisite-patch-id: ac9c23e579f4c3078a07d3e45373bc63729cf992
prerequisite-patch-id: d22bf3220b43f8f0bc29d0445edb7deaeb7e57b4
prerequisite-patch-id: fb4e676ec517317515f02fe4a2a482a64942c165
Best regards,
--
Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v3 1/5] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
@ 2026-10-30 12:43 ` Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 2/5] dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles Nihal Kumar Gupta
` (3 subsequent siblings)
4 siblings, 0 replies; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Document the Camera Control Interface (CCI) compatible for the Qualcomm
Hawi platform. Like other recent platforms it requires two clocks, so
add it to the corresponding clocks constraint as well.
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml b/Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml
index 1e8def25ec0ec1ef6b34859709d10a2a36fe36f5..b2b4d4bcf780792515ec153c873bace1764fb3e3 100644
--- a/Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml
+++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-cci.yaml
@@ -27,6 +27,7 @@ properties:
- items:
- enum:
- qcom,glymur-cci
+ - qcom,hawi-cci
- qcom,kaanapali-cci
- qcom,milos-cci
- qcom,qcm2290-cci
@@ -137,6 +138,7 @@ allOf:
contains:
enum:
- qcom,glymur-cci
+ - qcom,hawi-cci
- qcom,kaanapali-cci
- qcom,qcm2290-cci
- qcom,qcs8300-cci
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 2/5] dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 1/5] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible Nihal Kumar Gupta
@ 2026-10-30 12:43 ` Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili Nihal Kumar Gupta
` (2 subsequent siblings)
4 siblings, 0 replies; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media,
Krzysztof Kozlowski
Hawi and Maili integrate the same CSIPHY IP as Kaanapali with an
identical register interface. Add qcom,hawi-csi2-phy and
qcom,maili-csi2-phy falling back to qcom,hawi-csi2-phy.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Co-developed-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
index 6e9eb8e265df93b631101ae13f31f6365b6239b6..627aebc7cd9b7ca313457d3f70f72796e9671e8a 100644
--- a/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,x1e80100-csi2-phy.yaml
@@ -18,11 +18,16 @@ properties:
compatible:
oneOf:
- enum:
+ - qcom,hawi-csi2-phy
- qcom,kaanapali-csi2-phy
- qcom,x1e80100-csi2-phy
- items:
- const: qcom,glymur-csi2-phy
- const: qcom,x1e80100-csi2-phy
+ - items:
+ - enum:
+ - qcom,maili-csi2-phy
+ - const: qcom,hawi-csi2-phy
reg:
maxItems: 1
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 1/5] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 2/5] dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles Nihal Kumar Gupta
@ 2026-10-30 12:43 ` Nihal Kumar Gupta
2026-10-30 13:38 ` Loic Poulain
2026-10-30 12:43 ` [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 5/5] media: qcom: camss: Add support for Hawi Nihal Kumar Gupta
4 siblings, 1 reply; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Add bindings for Camera Subsystem (CAMSS) on the Qualcomm Hawi platform.
The Hawi platform provides:
- 6 x CSIPHY (CSI Physical Layer)
- 3 x TPG (Test Pattern Generator)
- 3 x CSID (CSI Decoder)
- 2 x CSID Lite
- 3 x VFE (Video Front End), 5 RDI per VFE
- 2 x VFE Lite, 4 RDI per VFE Lite
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Co-developed-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
.../devicetree/bindings/media/qcom,hawi-camss.yaml | 314 +++++++++++++++++++++
1 file changed, 314 insertions(+)
diff --git a/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml b/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml
new file mode 100644
index 0000000000000000000000000000000000000000..32c1cc59e8767b8b03f6947f8fde83d3e7410125
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml
@@ -0,0 +1,314 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/qcom,hawi-camss.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Hawi and Maili Camera Subsystem (CAMSS)
+
+maintainers:
+ - Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
+ - Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
+
+description:
+ The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms.
+
+properties:
+ compatible:
+ oneOf:
+ - const: qcom,hawi-camss
+ - items:
+ - const: qcom,maili-camss
+ - const: qcom,hawi-camss
+
+ reg:
+ maxItems: 14
+
+ reg-names:
+ items:
+ - const: top
+ - const: csid0
+ - const: csid1
+ - const: csid2
+ - const: csid_lite0
+ - const: csid_lite1
+ - const: csitpg0
+ - const: csitpg1
+ - const: csitpg2
+ - const: vfe0
+ - const: vfe1
+ - const: vfe2
+ - const: vfe_lite0
+ - const: vfe_lite1
+
+ clocks:
+ maxItems: 26
+
+ clock-names:
+ items:
+ - const: camnoc_nrt_axi
+ - const: camnoc_rt_axi
+ - const: camnoc_dcd_xo
+ - const: cpas_ahb
+ - const: cpas_fast_ahb
+ - const: cpas_mnoc_hf
+ - const: cpas_mnoc_sf
+ - const: cpas_vfe0
+ - const: cpas_vfe1
+ - const: cpas_vfe2
+ - const: cpas_vfe_lite
+ - const: csid
+ - const: csid_csiphy_rx
+ - const: gcc_axi_hf
+ - const: gcc_axi_sf
+ - const: vfe0
+ - const: vfe0_fast_ahb
+ - const: vfe1
+ - const: vfe1_fast_ahb
+ - const: vfe2
+ - const: vfe2_fast_ahb
+ - const: vfe_lite
+ - const: vfe_lite_ahb
+ - const: vfe_lite_cphy_rx
+ - const: vfe_lite_csid
+ - const: qdss_debug_xo
+
+ interrupts:
+ maxItems: 10
+
+ interrupt-names:
+ items:
+ - const: csid0
+ - const: csid1
+ - const: csid2
+ - const: csid_lite0
+ - const: csid_lite1
+ - const: vfe0
+ - const: vfe1
+ - const: vfe2
+ - const: vfe_lite0
+ - const: vfe_lite1
+
+ interconnects:
+ maxItems: 2
+
+ interconnect-names:
+ items:
+ - const: ahb
+ - const: hf_mnoc
+
+ iommus:
+ items:
+ - description: S1 HLOS IFE and IFE_LITE non-protected stream
+
+ power-domains:
+ items:
+ - description: IFE0 GDSC - Global Distributed Switch Controller for IFE0.
+ - description: IFE1 GDSC - Global Distributed Switch Controller for IFE1.
+ - description: IFE2 GDSC - Global Distributed Switch Controller for IFE2.
+ - description: Titan GDSC - Global Distributed Switch Controller for the entire camss.
+
+ power-domain-names:
+ items:
+ - const: ife0
+ - const: ife1
+ - const: ife2
+ - const: top
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ description:
+ CSI input ports.
+
+ patternProperties:
+ "^port@[0-5]$":
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Input ports for receiving CSI data on CSIPHY 0-5.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ data-lanes:
+ minItems: 1
+ maxItems: 4
+
+ bus-type:
+ enum:
+ - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
+ - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
+
+required:
+ - compatible
+ - reg
+ - reg-names
+ - clocks
+ - clock-names
+ - interrupts
+ - interrupt-names
+ - interconnects
+ - interconnect-names
+ - iommus
+ - power-domains
+ - power-domain-names
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/qcom,hawi-gcc.h>
+ #include <dt-bindings/clock/qcom,hawi-camcc.h>
+ #include <dt-bindings/interconnect/qcom,icc.h>
+ #include <dt-bindings/interconnect/qcom,hawi-rpmh.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/power/qcom,rpmhpd.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ isp@9253000 {
+ compatible = "qcom,hawi-camss";
+
+ reg = <0x0 0x0900b000 0x0 0x1000>,
+ <0x0 0x09253000 0x0 0x5e80>,
+ <0x0 0x09263000 0x0 0x5e80>,
+ <0x0 0x09273000 0x0 0x5e80>,
+ <0x0 0x092d3000 0x0 0x3880>,
+ <0x0 0x092e7000 0x0 0x3880>,
+ <0x0 0x093fd000 0x0 0x400>,
+ <0x0 0x093fe000 0x0 0x400>,
+ <0x0 0x093ff000 0x0 0x400>,
+ <0x0 0x09151000 0x0 0x20000>,
+ <0x0 0x09171000 0x0 0x20000>,
+ <0x0 0x09191000 0x0 0x20000>,
+ <0x0 0x092dc000 0x0 0x6800>,
+ <0x0 0x092f0000 0x0 0x6800>;
+ reg-names = "top",
+ "csid0",
+ "csid1",
+ "csid2",
+ "csid_lite0",
+ "csid_lite1",
+ "csitpg0",
+ "csitpg1",
+ "csitpg2",
+ "vfe0",
+ "vfe1",
+ "vfe2",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ clocks = <&camcc CAM_CC_CAMNOC_NRT_AXI_CLK>,
+ <&camcc CAM_CC_CAMNOC_RT_AXI_CLK>,
+ <&camcc CAM_CC_CAMNOC_DCD_XO_CLK>,
+ <&camcc CAM_CC_CAM_TOP_AHB_CLK>,
+ <&camcc CAM_CC_CAM_TOP_FAST_AHB_CLK>,
+ <&camcc CAM_CC_TITAN_MNOC_HF_CLK>,
+ <&camcc CAM_CC_TITAN_MNOC_SF_CLK>,
+ <&camcc CAM_CC_CAMNOC_RT_TFE_0_MAIN_CLK>,
+ <&camcc CAM_CC_CAMNOC_RT_TFE_1_MAIN_CLK>,
+ <&camcc CAM_CC_CAMNOC_RT_TFE_2_MAIN_CLK>,
+ <&camcc CAM_CC_CAMNOC_RT_IFE_LITE_CLK>,
+ <&camcc CAM_CC_CSID_CLK>,
+ <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>,
+ <&gcc GCC_CAMERA_HF_AXI_CLK>,
+ <&gcc GCC_CAMERA_SF_AXI_CLK>,
+ <&camcc CAM_CC_TFE_0_MAIN_CLK>,
+ <&camcc CAM_CC_TFE_0_MAIN_FAST_AHB_CLK>,
+ <&camcc CAM_CC_TFE_1_MAIN_CLK>,
+ <&camcc CAM_CC_TFE_1_MAIN_FAST_AHB_CLK>,
+ <&camcc CAM_CC_TFE_2_MAIN_CLK>,
+ <&camcc CAM_CC_TFE_2_MAIN_FAST_AHB_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CLK>,
+ <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
+ <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+ <&camcc CAM_CC_QDSS_DEBUG_XO_CLK>;
+ clock-names = "camnoc_nrt_axi",
+ "camnoc_rt_axi",
+ "camnoc_dcd_xo",
+ "cpas_ahb",
+ "cpas_fast_ahb",
+ "cpas_mnoc_hf",
+ "cpas_mnoc_sf",
+ "cpas_vfe0",
+ "cpas_vfe1",
+ "cpas_vfe2",
+ "cpas_vfe_lite",
+ "csid",
+ "csid_csiphy_rx",
+ "gcc_axi_hf",
+ "gcc_axi_sf",
+ "vfe0",
+ "vfe0_fast_ahb",
+ "vfe1",
+ "vfe1_fast_ahb",
+ "vfe2",
+ "vfe2_fast_ahb",
+ "vfe_lite",
+ "vfe_lite_ahb",
+ "vfe_lite_cphy_rx",
+ "vfe_lite_csid",
+ "qdss_debug_xo";
+
+ interrupts = <GIC_SPI 601 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 603 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 433 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 436 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 457 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 606 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "csid0",
+ "csid1",
+ "csid2",
+ "csid_lite0",
+ "csid_lite1",
+ "vfe0",
+ "vfe1",
+ "vfe2",
+ "vfe_lite0",
+ "vfe_lite1";
+
+ interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+ &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>,
+ <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
+ interconnect-names = "ahb",
+ "hf_mnoc";
+
+ iommus = <&apps_smmu 0x1800 0x00>;
+
+ power-domains = <&camcc CAM_CC_TFE_0_GDSC>,
+ <&camcc CAM_CC_TFE_1_GDSC>,
+ <&camcc CAM_CC_TFE_2_GDSC>,
+ <&camcc CAM_CC_TITAN_TOP_GDSC>;
+ power-domain-names = "ife0",
+ "ife1",
+ "ife2",
+ "top";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ camss_csiphy0_ep: endpoint {
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&csiphy0_out>;
+ };
+ };
+ };
+ };
+ };
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
` (2 preceding siblings ...)
2026-10-30 12:43 ` [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili Nihal Kumar Gupta
@ 2026-10-30 12:43 ` Nihal Kumar Gupta
2026-10-30 13:39 ` Loic Poulain
2026-10-30 12:43 ` [PATCH v3 5/5] media: qcom: camss: Add support for Hawi Nihal Kumar Gupta
4 siblings, 1 reply; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Add support for the Hawi 2nm CSI-2 D-PHY.
Reuse the Kaanapali lane table and adjust the data-lane CTRL0 value
from 0x8e to 0x8c for Hawi-specific tuning. This prevents potential
stream stalls and SMMU faults.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c | 136 +++++++++++++++++++++
drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c | 1 +
drivers/phy/qualcomm/phy-qcom-mipi-csi2.h | 1 +
3 files changed, 138 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
index 658a39463104bedfa31d0ccb81fd9d34017e91a6..1e9bb8b9e50bb15e7fad3c6e3d6048bf049e3e64 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
@@ -162,6 +162,126 @@ mipi_csi2phy_lane_regs lane_regs_x1e80100[] = {
{.reg_addr = 0x0c64, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
};
+/* 2nm 2PH 2p5Gbps 4 lane DPHY mode, Kaanapali table with data-lane CTRL0 0x8c */
+static const struct mipi_csi2phy_lane_regs lane_regs_hawi[] = {
+ /* Power up lanes in 2ph mode. */
+ { .reg_addr = 0x101c, .reg_data = 0x7a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x1018, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+
+ { .reg_addr = 0x0094, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x00a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0090, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0098, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0094, .reg_data = 0x07, .delay_us = 1,
+ .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0030, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0000, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0038, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x002c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0034, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x001c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0014, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x003c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0004, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0020, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0008, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
+ { .reg_addr = 0x0010, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0094, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x005c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0060, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0064, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
+
+ { .reg_addr = 0x0e94, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0ea0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e90, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e98, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e94, .reg_data = 0x07, .delay_us = 1,
+ .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e30, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e28, .reg_data = 0x04, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e00, .reg_data = 0x80, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e0c, .reg_data = 0xff, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e38, .reg_data = 0x1f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e2c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e34, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e1c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e14, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e3c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e04, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e20, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0e08, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
+ { .reg_addr = 0x0e10, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
+
+ { .reg_addr = 0x0494, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x04a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0490, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0498, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0494, .reg_data = 0x07, .delay_us = 1,
+ .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0430, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0400, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0438, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x042c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0434, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x041c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0414, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x043c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0404, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0420, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0408, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
+ { .reg_addr = 0x0410, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0494, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x045c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0460, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0464, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
+
+ { .reg_addr = 0x0894, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x08a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0890, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0898, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0894, .reg_data = 0x07, .delay_us = 1,
+ .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0830, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0800, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0838, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x082c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0834, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x081c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0814, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x083c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0804, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0820, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0808, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
+ { .reg_addr = 0x0810, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0894, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x085c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0860, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0864, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
+
+ { .reg_addr = 0x0c94, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0ca0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c90, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c98, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c94, .reg_data = 0x07, .delay_us = 1,
+ .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c30, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c00, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c38, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c2c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c34, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c1c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c14, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c3c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c04, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c20, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c08, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
+ { .reg_addr = 0x0c10, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
+ { .reg_addr = 0x0c94, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0c5c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0c60, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
+ { .reg_addr = 0x0c64, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
+};
+
static inline const struct mipi_csi2phy_device_regs *
csi2phy_dev_to_regs(struct mipi_csi2phy_device *csi2phy)
{
@@ -405,3 +525,19 @@ const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_3nm_kaanapali = {
.genpds = x1e_genpds,
.num_genpds = ARRAY_SIZE(x1e_genpds),
};
+
+const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_2nm_hawi = {
+ .ops = &phy_qcom_mipi_csi2_ops_3ph_1_0,
+ .reg_info = {
+ .init_seq = lane_regs_hawi,
+ .lane_array_size = ARRAY_SIZE(lane_regs_hawi),
+ .common_regs_offset = 0x1000,
+ .common_status_offset = 0x138,
+ },
+ .supply_names = (const char **)x1e_supplies,
+ .num_supplies = ARRAY_SIZE(x1e_supplies),
+ .clk_names = (const char **)x1e_clks,
+ .num_clk = ARRAY_SIZE(x1e_clks),
+ .genpds = x1e_genpds,
+ .num_genpds = ARRAY_SIZE(x1e_genpds),
+};
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
index aff9e66f0352e1d4d7a07d10d350ea2cba6df233..76c55f8e30b8c629818762d0b42a7dc4ddc6716b 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
@@ -445,6 +445,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
static const struct of_device_id phy_qcom_mipi_csi2_of_match_table[] = {
{ .compatible = "qcom,x1e80100-csi2-phy", .data = &mipi_csi2_dphy_4nm_x1e },
{ .compatible = "qcom,kaanapali-csi2-phy", .data = &mipi_csi2_dphy_3nm_kaanapali },
+ { .compatible = "qcom,hawi-csi2-phy", .data = &mipi_csi2_dphy_2nm_hawi },
{ }
};
MODULE_DEVICE_TABLE(of, phy_qcom_mipi_csi2_of_match_table);
diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
index 2355a1db9b941469325646ef81d0f70c6a2badc4..4ad058b916ebba8b319cb297c231cba10d3ec602 100644
--- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
+++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
@@ -95,5 +95,6 @@ struct mipi_csi2phy_device {
extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e;
extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_3nm_kaanapali;
+extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_2nm_hawi;
#endif /* __PHY_QCOM_MIPI_CSI2_H__ */
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH v3 5/5] media: qcom: camss: Add support for Hawi
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
` (3 preceding siblings ...)
2026-10-30 12:43 ` [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support Nihal Kumar Gupta
@ 2026-10-30 12:43 ` Nihal Kumar Gupta
2026-10-30 15:04 ` Bryan O'Donoghue
2026-10-30 15:05 ` Bryan O'Donoghue
4 siblings, 2 replies; 13+ messages in thread
From: Nihal Kumar Gupta @ 2026-10-30 12:43 UTC (permalink / raw)
To: Loic Poulain, Robert Foss, Andi Shyti, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue,
Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Hangxiang Ma,
Nihal Kumar Gupta, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Add CAMSS support for the Hawi SoC. The CSIPHY resource table is reused
from Kaanapali and the TPG table from X1E80100.
Hawi calls its front-end blocks TFEs (Thin Front Ends), but the VFE 1190
driver keeps the VFE naming for consistency. The common CPAS clocks are
managed as PM clocks of the CAMSS resources rather than per-VFE clocks.
CSID 1190 splits RUP and AUP updates into separate registers committed
through a SET register, so the driver provides separate reg_update and
addr_update operations, and VFE 1190 wires up addr_update. The SOF and
EOF INFO bits are also defined.
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
---
drivers/media/platform/qcom/camss/Makefile | 2 +
.../media/platform/qcom/camss/camss-csid-1190.c | 417 +++++++++++++++++++++
drivers/media/platform/qcom/camss/camss-csid.h | 1 +
drivers/media/platform/qcom/camss/camss-vfe-1190.c | 217 +++++++++++
drivers/media/platform/qcom/camss/camss-vfe.c | 2 +
drivers/media/platform/qcom/camss/camss-vfe.h | 1 +
drivers/media/platform/qcom/camss/camss.c | 229 +++++++++++
drivers/media/platform/qcom/camss/camss.h | 1 +
8 files changed, 870 insertions(+)
diff --git a/drivers/media/platform/qcom/camss/Makefile b/drivers/media/platform/qcom/camss/Makefile
index 42a14e8fe1b7f28ba5ffcbe59769093b08db4d6b..e48df14933fa0e2b1910de5e68bec0b5c57dd1b2 100644
--- a/drivers/media/platform/qcom/camss/Makefile
+++ b/drivers/media/platform/qcom/camss/Makefile
@@ -9,6 +9,7 @@ qcom-camss-objs += \
camss-csid-340.o \
camss-csid-680.o \
camss-csid-1080.o \
+ camss-csid-1190.o \
camss-csid-gen2.o \
camss-csid-gen3.o \
camss-csiphy.o \
@@ -27,6 +28,7 @@ qcom-camss-objs += \
camss-vfe-480.o \
camss-vfe-680.o \
camss-vfe-1080.o \
+ camss-vfe-1190.o \
camss-vfe-gen1.o \
camss-vfe-gen3.o \
camss-vfe-vbif.o \
diff --git a/drivers/media/platform/qcom/camss/camss-csid-1190.c b/drivers/media/platform/qcom/camss/camss-csid-1190.c
new file mode 100644
index 0000000000000000000000000000000000000000..4bd2cce0944022ce0f987faa0e34417a665c0aa4
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-csid-1190.c
@@ -0,0 +1,417 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * camss-csid-1190.c
+ *
+ * Qualcomm MSM Camera Subsystem - CSID (CSI Decoder) Module
+ *
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of.h>
+
+#include "camss.h"
+#include "camss-csid.h"
+#include "camss-csid-gen3.h"
+
+/* Reset and Command Registers */
+#define CSID_RST_CFG 0x108
+#define RST_MODE BIT(0)
+#define RST_LOCATION BIT(4)
+
+/* Reset and Command Registers */
+#define CSID_RST_CMD 0x10C
+#define SELECT_HW_RST BIT(0)
+#define SELECT_IRQ_RST BIT(2)
+#define CSID_IRQ_CMD 0x110
+#define IRQ_CMD_CLEAR BIT(0)
+
+/* Register Update Commands, RUP/AUP */
+#define CSID_RUP_CMD 0x114
+#define CSID_AUP_CMD 0x118
+#define CSID_RUP_AUP_RDI(rdi) (BIT(8) << (rdi))
+#define CSID_RUP_AUP_CMD 0x11C
+#define RUP_SET BIT(0)
+#define MUP BIT(4)
+
+/* Top level interrupt registers */
+#define CSID_TOP_IRQ_STATUS 0x180
+#define CSID_TOP_IRQ_MASK 0x184
+#define CSID_TOP_IRQ_CLEAR 0x188
+#define INFO_RST_DONE BIT(0)
+#define CSI2_RX_IRQ_STATUS BIT(2)
+#define BUF_DONE_IRQ_STATUS BIT(3)
+#define TOP_IRQ_STATUS_RDI_OFFSET 16
+
+/* Buffer done interrupt registers */
+#define CSID_BUF_DONE_IRQ_STATUS 0x1A0
+#define BUF_DONE_IRQ_STATUS_RDI_OFFSET 16
+#define CSID_BUF_DONE_IRQ_MASK 0x1A4
+#define CSID_BUF_DONE_IRQ_CLEAR 0x1A8
+#define CSID_BUF_DONE_IRQ_SET 0x1AC
+
+/* CSI2 RX interrupt registers */
+#define CSID_CSI2_RX_IRQ_STATUS 0x1B0
+#define CSID_CSI2_RX_IRQ_MASK 0x1B4
+#define CSID_CSI2_RX_IRQ_CLEAR 0x1B8
+#define CSID_CSI2_RX_IRQ_SET 0x1BC
+
+/* CSI2 RX Configuration */
+#define CSID_CSI2_RX_CFG0 0x880
+#define CSI2_RX_CFG0_NUM_ACTIVE_LANES 0
+#define CSI2_RX_CFG0_DL0_INPUT_SEL 4
+#define CSI2_RX_CFG0_PHY_NUM_SEL 20
+#define CSI2_RX_CFG0_TPG_MUX_EN BIT(27)
+#define CSI2_RX_CFG0_TPG_MUX_SEL GENMASK(29, 28)
+#define CSI2_RX_CFG0_PHY_SEL_BASE_IDX 1
+#define CSID_CSI2_RX_CFG1 0x884
+#define CSI2_RX_CFG1_ECC_CORRECTION_EN BIT(0)
+#define CSI2_RX_CFG1_VC_MODE BIT(2)
+
+#define MSM_CSID_MAX_SRC_STREAMS_1190 (csid_is_lite(csid) ? 4 : 5)
+
+/* RDI Configuration */
+#define CSID_RDI_CFG0(rdi) (csid_is_lite(csid) ?\
+ (0x3080 + 0x200 * (rdi)) :\
+ (0x5480 + 0x200 * (rdi)))
+#define RDI_CFG0_RETIME_BS BIT(5)
+#define RDI_CFG0_TIMESTAMP_EN BIT(6)
+#define RDI_CFG0_TIMESTAMP_STB_SEL BIT(8)
+#define RDI_CFG0_DECODE_FORMAT 12
+#define RDI_CFG0_DT 16
+#define RDI_CFG0_VC 22
+#define RDI_CFG0_EN BIT(31)
+
+/* RDI Control and Configuration */
+#define CSID_RDI_CTRL(rdi) (csid_is_lite(csid) ?\
+ (0x3088 + 0x200 * (rdi)) :\
+ (0x5488 + 0x200 * (rdi)))
+#define RDI_CTRL_START_CMD BIT(0)
+
+#define CSID_RDI_CFG1(rdi) (csid_is_lite(csid) ?\
+ (0x3094 + 0x200 * (rdi)) :\
+ (0x5494 + 0x200 * (rdi)))
+#define RDI_CFG1_DROP_H_EN BIT(5)
+#define RDI_CFG1_DROP_V_EN BIT(6)
+#define RDI_CFG1_CROP_H_EN BIT(7)
+#define RDI_CFG1_CROP_V_EN BIT(8)
+#define RDI_CFG1_PACKING_FORMAT_MIPI BIT(15)
+
+/* RDI Pixel Store Configuration */
+#define CSID_RDI_PIX_STORE_CFG0(rdi) (0x5498 + 0x200 * (rdi))
+#define RDI_PIX_STORE_CFG0_EN BIT(0)
+#define RDI_PIX_STORE_CFG0_MIN_HBI 1
+
+/* RDI IRQ Status in wrapper */
+#define CSID_CSI2_RDIN_IRQ_STATUS(rdi) (0x224 + (0x10 * (rdi)))
+#define CSID_CSI2_RDIN_IRQ_MASK(rdi) (0x228 + (0x10 * (rdi)))
+#define CSID_CSI2_RDIN_IRQ_CLEAR(rdi) (0x22C + (0x10 * (rdi)))
+#define INFO_RUP_DONE BIT(23)
+#define INFO_INPUT_SOF BIT(12)
+#define INFO_INPUT_EOF BIT(9)
+#define INFO_CAMIF_SOF BIT(4)
+#define INFO_CAMIF_EOF BIT(3)
+
+static void __csid_aup_rup_trigger(struct csid_device *csid)
+{
+ /* trigger SET in combined register */
+ writel(RUP_SET, csid->base + CSID_RUP_AUP_CMD);
+}
+
+static void __csid_addr_update(struct csid_device *csid, int port_id)
+{
+ csid->addr_update |= CSID_RUP_AUP_RDI(port_id);
+ writel(csid->addr_update, csid->base + CSID_AUP_CMD);
+
+ __csid_aup_rup_trigger(csid);
+}
+
+static void __csid_addr_update_clear(struct csid_device *csid, int port_id)
+{
+ /* Hardware clears the registers upon consuming the settings */
+ csid->addr_update &= ~CSID_RUP_AUP_RDI(port_id);
+}
+
+static void __csid_reg_update(struct csid_device *csid, int port_id)
+{
+ csid->reg_update |= CSID_RUP_AUP_RDI(port_id);
+ writel(csid->reg_update, csid->base + CSID_RUP_CMD);
+
+ __csid_aup_rup_trigger(csid);
+}
+
+static void __csid_reg_update_clear(struct csid_device *csid, int port_id)
+{
+ /* Hardware clears the registers upon consuming the settings */
+ csid->reg_update &= ~CSID_RUP_AUP_RDI(port_id);
+}
+
+static void __csid_configure_rx(struct csid_device *csid,
+ struct csid_phy_config *phy)
+{
+ struct camss *camss = csid->camss;
+ u8 lane_cnt = csid->phy.lane_cnt;
+ int val;
+
+ if (!lane_cnt)
+ lane_cnt = 4;
+
+ val = (lane_cnt - 1) << CSI2_RX_CFG0_NUM_ACTIVE_LANES;
+ val |= phy->lane_assign << CSI2_RX_CFG0_DL0_INPUT_SEL;
+
+ if (camss->tpg && csid->tpg_linked &&
+ camss->tpg[phy->csiphy_id].testgen.mode != TPG_PAYLOAD_MODE_DISABLED) {
+ val |= FIELD_PREP(CSI2_RX_CFG0_TPG_MUX_SEL, phy->csiphy_id + 1);
+ val |= CSI2_RX_CFG0_TPG_MUX_EN;
+ } else {
+ val |= (phy->csiphy_id + CSI2_RX_CFG0_PHY_SEL_BASE_IDX)
+ << CSI2_RX_CFG0_PHY_NUM_SEL;
+ }
+
+ writel(val, csid->base + CSID_CSI2_RX_CFG0);
+
+ val = CSI2_RX_CFG1_ECC_CORRECTION_EN;
+ writel(val, csid->base + CSID_CSI2_RX_CFG1);
+}
+
+static void __csid_configure_rx_vc(struct csid_device *csid, int vc)
+{
+ int val;
+
+ if (vc > 3) {
+ val = readl(csid->base + CSID_CSI2_RX_CFG1);
+ val |= CSI2_RX_CFG1_VC_MODE;
+ writel(val, csid->base + CSID_CSI2_RX_CFG1);
+ }
+}
+
+static void __csid_ctrl_rdi(struct csid_device *csid, int enable, u8 rdi)
+{
+ int val = 0;
+
+ if (enable)
+ val = RDI_CTRL_START_CMD;
+
+ writel(val, csid->base + CSID_RDI_CTRL(rdi));
+}
+
+static void __csid_configure_rdi_pix_store(struct csid_device *csid, u8 rdi)
+{
+ u32 val;
+
+ /*
+ * Configure pixel store to allow absorption of hblanking or idle time.
+ * This helps with horizontal crop and prevents line buffer conflicts.
+ * Reset state is 0x8 which has MIN_HBI=4, we keep the default MIN_HBI
+ * and just enable the pixel store functionality.
+ */
+ val = (4 << RDI_PIX_STORE_CFG0_MIN_HBI) | RDI_PIX_STORE_CFG0_EN;
+ writel(val, csid->base + CSID_RDI_PIX_STORE_CFG0(rdi));
+}
+
+static void __csid_configure_rdi_stream(struct csid_device *csid, u8 enable, u8 port, u8 vc)
+{
+ u32 val;
+ u8 lane_cnt = csid->phy.lane_cnt;
+
+ /* Source pads matching RDI channels on hardware.
+ * E.g. Pad 1 -> RDI0, Pad 2 -> RDI1, etc.
+ */
+ struct v4l2_mbus_framefmt *input_format = &csid->fmt[MSM_CSID_PAD_FIRST_SRC + port];
+ const struct csid_format_info *format = csid_get_fmt_entry(csid->res->formats->formats,
+ csid->res->formats->nformats,
+ input_format->code);
+
+ if (!lane_cnt)
+ lane_cnt = 4;
+
+ val = RDI_CFG0_TIMESTAMP_EN;
+ val |= RDI_CFG0_TIMESTAMP_STB_SEL;
+ val |= RDI_CFG0_RETIME_BS;
+
+ /* note: for non-RDI path, this should be format->decode_format */
+ val |= DECODE_FORMAT_PAYLOAD_ONLY << RDI_CFG0_DECODE_FORMAT;
+ val |= vc << RDI_CFG0_VC;
+ val |= format->data_type << RDI_CFG0_DT;
+ writel(val, csid->base + CSID_RDI_CFG0(port));
+
+ val = RDI_CFG1_PACKING_FORMAT_MIPI;
+ writel(val, csid->base + CSID_RDI_CFG1(port));
+
+ /* Configure pixel store using dedicated register in 1190 */
+ if (!csid_is_lite(csid))
+ __csid_configure_rdi_pix_store(csid, port);
+
+ val = 0;
+ writel(val, csid->base + CSID_RDI_CTRL(port));
+
+ val = readl(csid->base + CSID_RDI_CFG0(port));
+
+ if (enable)
+ val |= RDI_CFG0_EN;
+
+ writel(val, csid->base + CSID_RDI_CFG0(port));
+}
+
+static void csid_configure_stream(struct csid_device *csid, u8 enable)
+{
+ u8 i, k;
+
+ __csid_configure_rx(csid, &csid->phy);
+
+ for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS_1190; i++) {
+ if (csid->phy.en_vc & BIT(i)) {
+ __csid_configure_rdi_stream(csid, enable, i, 0);
+ __csid_configure_rx_vc(csid, 0);
+
+ for (k = 0; k < CAMSS_INIT_BUF_COUNT; k++)
+ __csid_addr_update(csid, i);
+
+ __csid_reg_update(csid, i);
+
+ __csid_ctrl_rdi(csid, enable, i);
+ }
+ }
+}
+
+static int csid_configure_testgen_pattern(struct csid_device *csid, s32 val)
+{
+ return 0;
+}
+
+static void csid_subdev_reg_update(struct csid_device *csid, int port_id,
+ bool clear)
+{
+ if (clear)
+ __csid_reg_update_clear(csid, port_id);
+ else
+ __csid_reg_update(csid, port_id);
+}
+
+static void csid_subdev_addr_update(struct csid_device *csid, int port_id,
+ bool clear)
+{
+ if (clear)
+ __csid_addr_update_clear(csid, port_id);
+ else
+ __csid_addr_update(csid, port_id);
+}
+
+/**
+ * csid_isr - CSID module interrupt service routine
+ * @irq: Interrupt line
+ * @dev: CSID device
+ *
+ * Return IRQ_HANDLED on success
+ */
+static irqreturn_t csid_isr(int irq, void *dev)
+{
+ struct csid_device *csid = dev;
+ u32 val, buf_done_val;
+ u8 reset_done;
+ int i;
+
+ val = readl(csid->base + CSID_TOP_IRQ_STATUS);
+ writel(val, csid->base + CSID_TOP_IRQ_CLEAR);
+
+ reset_done = val & INFO_RST_DONE;
+
+ buf_done_val = readl(csid->base + CSID_BUF_DONE_IRQ_STATUS);
+ writel(buf_done_val, csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+
+ for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS_1190; i++) {
+ if (csid->phy.en_vc & BIT(i)) {
+ val = readl(csid->base + CSID_CSI2_RDIN_IRQ_STATUS(i));
+ writel(val, csid->base + CSID_CSI2_RDIN_IRQ_CLEAR(i));
+
+ if (val & INFO_RUP_DONE) {
+ __csid_addr_update_clear(csid, i);
+ __csid_reg_update_clear(csid, i);
+ }
+
+ if (buf_done_val & BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i))
+ camss_buf_done(csid->camss, csid->id, i);
+ }
+ }
+
+ val = IRQ_CMD_CLEAR;
+ writel(val, csid->base + CSID_IRQ_CMD);
+
+ if (reset_done)
+ complete(&csid->reset_complete);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * csid_reset - Trigger reset on CSID module and wait to complete
+ * @csid: CSID device
+ *
+ * Return 0 on success or a negative error code otherwise
+ */
+static int csid_reset(struct csid_device *csid)
+{
+ unsigned long time;
+ u32 val;
+ int i;
+
+ reinit_completion(&csid->reset_complete);
+
+ val = INFO_RST_DONE | BUF_DONE_IRQ_STATUS;
+ writel(val, csid->base + CSID_TOP_IRQ_CLEAR);
+ writel(val, csid->base + CSID_TOP_IRQ_MASK);
+
+ val = 0;
+ for (i = 0; i < MSM_CSID_MAX_SRC_STREAMS_1190; i++) {
+ if (csid->phy.en_vc & BIT(i)) {
+ /*
+ * Only need to clear buf done IRQ status here,
+ * RUP done IRQ status will be cleared once isr
+ * strobe generated by CSID_RST_CMD
+ */
+ val |= BIT(BUF_DONE_IRQ_STATUS_RDI_OFFSET + i);
+ }
+ }
+ writel(val, csid->base + CSID_BUF_DONE_IRQ_CLEAR);
+ writel(val, csid->base + CSID_BUF_DONE_IRQ_MASK);
+
+ /* Clear all IRQ status with CLEAR bits set */
+ val = IRQ_CMD_CLEAR;
+ writel(val, csid->base + CSID_IRQ_CMD);
+
+ val = RST_LOCATION | RST_MODE;
+ writel(val, csid->base + CSID_RST_CFG);
+
+ val = SELECT_HW_RST | SELECT_IRQ_RST;
+ writel(val, csid->base + CSID_RST_CMD);
+
+ time = wait_for_completion_timeout(&csid->reset_complete,
+ msecs_to_jiffies(CSID_RESET_TIMEOUT_MS));
+
+ if (!time) {
+ dev_err(csid->camss->dev, "CSID reset timeout\n");
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static void csid_subdev_init(struct csid_device *csid)
+{
+ csid->testgen.nmodes = CSID_PAYLOAD_MODE_DISABLED;
+}
+
+const struct csid_hw_ops csid_ops_1190 = {
+ .configure_stream = csid_configure_stream,
+ .configure_testgen_pattern = csid_configure_testgen_pattern,
+ .hw_version = csid_hw_version,
+ .isr = csid_isr,
+ .reset = csid_reset,
+ .src_pad_code = csid_src_pad_code,
+ .subdev_init = csid_subdev_init,
+ .reg_update = csid_subdev_reg_update,
+ .addr_update = csid_subdev_addr_update,
+};
diff --git a/drivers/media/platform/qcom/camss/camss-csid.h b/drivers/media/platform/qcom/camss/camss-csid.h
index a3ab2a384bb49ac24955e86c8452a8ce36ce71b2..7bdf183d28c8ac33833cc974cae2cc79d4bef415 100644
--- a/drivers/media/platform/qcom/camss/camss-csid.h
+++ b/drivers/media/platform/qcom/camss/camss-csid.h
@@ -226,6 +226,7 @@ extern const struct csid_hw_ops csid_ops_4_7;
extern const struct csid_hw_ops csid_ops_340;
extern const struct csid_hw_ops csid_ops_680;
extern const struct csid_hw_ops csid_ops_1080;
+extern const struct csid_hw_ops csid_ops_1190;
extern const struct csid_hw_ops csid_ops_gen2;
extern const struct csid_hw_ops csid_ops_gen3;
diff --git a/drivers/media/platform/qcom/camss/camss-vfe-1190.c b/drivers/media/platform/qcom/camss/camss-vfe-1190.c
new file mode 100644
index 0000000000000000000000000000000000000000..246519c2294b8d5021ebdd95e056f00d20897a0f
--- /dev/null
+++ b/drivers/media/platform/qcom/camss/camss-vfe-1190.c
@@ -0,0 +1,217 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * camss-vfe-1190.c
+ *
+ * Qualcomm MSM Camera Subsystem - VFE (Video Front End) Module 1190
+ *
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+
+#include "camss.h"
+#include "camss-vfe.h"
+
+/* VFE-1190 Bus Register Base Addresses */
+#define BUS_REG_BASE (0x800)
+#define BUS_REG_OFFSET(n) (0x1000 + (n) * 0x200)
+
+#define VFE_BUS_WM_CGC_OVERRIDE (BUS_REG_BASE + 0x4)
+#define WM_CGC_OVERRIDE_ALL (0x7FFFFFF)
+
+#define VFE_BUS_WM_TEST_BUS_CTRL (BUS_REG_BASE + 0x144)
+
+#define VFE_BUS_WM_CFG(n) (BUS_REG_BASE + BUS_REG_OFFSET(n))
+#define WM_CFG_EN BIT(0)
+#define WM_VIR_FRM_EN BIT(1)
+#define WM_CFG_MODE BIT(16)
+#define VFE_BUS_WM_IMAGE_ADDR(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x4)
+#define VFE_BUS_WM_FRAME_INCR(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x8)
+#define VFE_BUS_WM_IMAGE_CFG_0(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0xC)
+#define WM_IMAGE_CFG_0_DEFAULT_WIDTH (0xFFFF)
+#define VFE_BUS_WM_IMAGE_CFG_2(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x14)
+#define WM_IMAGE_CFG_2_DEFAULT_STRIDE (0xFFFF)
+#define VFE_BUS_WM_PACKER_CFG(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x18)
+
+#define VFE_BUS_WM_IRQ_SUBSAMPLE_PERIOD(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x30)
+#define VFE_BUS_WM_IRQ_SUBSAMPLE_PATTERN(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x34)
+
+/* VFE lite has no such registers */
+#define VFE_BUS_WM_FRAMEDROP_PERIOD(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x38)
+#define VFE_BUS_WM_FRAMEDROP_PATTERN(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x3C)
+
+#define VFE_BUS_WM_MMU_PREFETCH_CFG(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x64)
+#define VFE_BUS_WM_MMU_PREFETCH_MAX_OFFSET(n) (BUS_REG_BASE + BUS_REG_OFFSET(n) + 0x68)
+
+/*
+ * VFE 1190 write master client IDs
+ *
+ * VIDEO_FULL_Y 0
+ * VIDEO_FULL_UV 1
+ * VIDEO_DC4_Y 2
+ * VIDEO_DC4_C 3
+ * VIDEO_DC16_Y 4
+ * VIDEO_DC16_C 5
+ * FD_Y 6
+ * FD_C 7
+ * RAW_OUT 8
+ * STATS_AEC_BG 9
+ * STATS_AEC_BHIST 10
+ * STATS_TINTLESS_BG 11
+ * STATS_AWB_BG 12
+ * STATS_AWB_BFW 13
+ * STATS_AF_BHIST 14
+ * STATS_ALSC_BG 15
+ * STATS_FLICKER_BAYERRS 16
+ * STATS_TMC_BHIST 17
+ * PDAF_0 18
+ * PDAF_1 19
+ * PDAF_2 20
+ * PDAF_3 21
+ * PDAF_4 22
+ * RDI0 23
+ * RDI1 24
+ * RDI2 25
+ * RDI3 26
+ * RDI4 27
+ * C2PA Y 28
+ * C2PA C 29
+ *
+ * VFE Lite 1190 write master client IDs
+ *
+ * RDI0 0
+ * RDI1 1
+ * RDI2 2
+ * RDI3 3
+ * GAMMA 4
+ * STATES_BG 5
+ */
+#define RDI_WM(n) ((vfe_is_lite(vfe) ? 0x0 : 0x17) + (n))
+
+static void vfe_wm_start(struct vfe_device *vfe, u8 wm, struct vfe_line *line)
+{
+ struct v4l2_pix_format_mplane *pix =
+ &line->video_out.active_fmt.fmt.pix_mp;
+
+ wm = RDI_WM(wm);
+
+ /* no clock gating at bus input */
+ writel(WM_CGC_OVERRIDE_ALL, vfe->base + VFE_BUS_WM_CGC_OVERRIDE);
+
+ writel(0x0, vfe->base + VFE_BUS_WM_TEST_BUS_CTRL);
+
+ writel(ALIGN(pix->plane_fmt[0].bytesperline, 16) * pix->height >> 8,
+ vfe->base + VFE_BUS_WM_FRAME_INCR(wm));
+ writel((WM_IMAGE_CFG_0_DEFAULT_WIDTH & 0xFFFF),
+ vfe->base + VFE_BUS_WM_IMAGE_CFG_0(wm));
+ writel(WM_IMAGE_CFG_2_DEFAULT_STRIDE,
+ vfe->base + VFE_BUS_WM_IMAGE_CFG_2(wm));
+ writel(0, vfe->base + VFE_BUS_WM_PACKER_CFG(wm));
+
+ /* no dropped frames, one irq per frame */
+ if (!vfe_is_lite(vfe)) {
+ writel(0, vfe->base + VFE_BUS_WM_FRAMEDROP_PERIOD(wm));
+ writel(1, vfe->base + VFE_BUS_WM_FRAMEDROP_PATTERN(wm));
+ }
+
+ writel(0, vfe->base + VFE_BUS_WM_IRQ_SUBSAMPLE_PERIOD(wm));
+ writel(1, vfe->base + VFE_BUS_WM_IRQ_SUBSAMPLE_PATTERN(wm));
+
+ writel(1, vfe->base + VFE_BUS_WM_MMU_PREFETCH_CFG(wm));
+ writel(0xFFFFFFFF, vfe->base + VFE_BUS_WM_MMU_PREFETCH_MAX_OFFSET(wm));
+
+ writel(WM_CFG_EN | WM_CFG_MODE, vfe->base + VFE_BUS_WM_CFG(wm));
+}
+
+static void vfe_wm_stop(struct vfe_device *vfe, u8 wm)
+{
+ wm = RDI_WM(wm);
+ writel(0, vfe->base + VFE_BUS_WM_CFG(wm));
+}
+
+static void vfe_wm_update(struct vfe_device *vfe, u8 wm, u32 addr,
+ struct vfe_line *line)
+{
+ wm = RDI_WM(wm);
+ writel(addr >> 8, vfe->base + VFE_BUS_WM_IMAGE_ADDR(wm));
+
+ dev_dbg(vfe->camss->dev, "wm:%d, image buf addr:0x%x\n", wm, addr);
+}
+
+static void vfe_reg_update(struct vfe_device *vfe, enum vfe_line_id line_id)
+{
+ int port_id = line_id;
+
+ camss_reg_update(vfe->camss, vfe->id, port_id, false);
+}
+
+static inline void vfe_reg_update_clear(struct vfe_device *vfe,
+ enum vfe_line_id line_id)
+{
+ int port_id = line_id;
+
+ camss_reg_update(vfe->camss, vfe->id, port_id, true);
+}
+
+static void vfe_addr_update(struct vfe_device *vfe, enum vfe_line_id line_id)
+{
+ int port_id = line_id;
+
+ camss_addr_update(vfe->camss, vfe->id, port_id, false);
+}
+
+static inline void vfe_addr_update_clear(struct vfe_device *vfe,
+ enum vfe_line_id line_id)
+{
+ int port_id = line_id;
+
+ camss_addr_update(vfe->camss, vfe->id, port_id, true);
+}
+
+static const struct camss_video_ops vfe_video_ops_1190 = {
+ .queue_buffer = vfe_queue_buffer_v2,
+ .flush_buffers = vfe_flush_buffers,
+};
+
+static void vfe_subdev_init(struct device *dev, struct vfe_device *vfe)
+{
+ vfe->video_ops = vfe_video_ops_1190;
+}
+
+static void vfe_global_reset(struct vfe_device *vfe)
+{
+ vfe_isr_reset_ack(vfe);
+}
+
+static irqreturn_t vfe_isr(int irq, void *dev)
+{
+ /* nop */
+ return IRQ_HANDLED;
+}
+
+static int vfe_halt(struct vfe_device *vfe)
+{
+ /* rely on vfe_disable_output() to stop the VFE */
+ return 0;
+}
+
+const struct vfe_hw_ops vfe_ops_1190 = {
+ .addr_update = vfe_addr_update,
+ .addr_update_clear = vfe_addr_update_clear,
+ .global_reset = vfe_global_reset,
+ .hw_version = vfe_hw_version,
+ .isr = vfe_isr,
+ .pm_domain_off = vfe_pm_domain_off,
+ .pm_domain_on = vfe_pm_domain_on,
+ .reg_update = vfe_reg_update,
+ .reg_update_clear = vfe_reg_update_clear,
+ .subdev_init = vfe_subdev_init,
+ .vfe_disable = vfe_disable,
+ .vfe_enable = vfe_enable_v2,
+ .vfe_halt = vfe_halt,
+ .vfe_wm_start = vfe_wm_start,
+ .vfe_wm_stop = vfe_wm_stop,
+ .vfe_buf_done = vfe_buf_done,
+ .vfe_wm_update = vfe_wm_update,
+};
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.c b/drivers/media/platform/qcom/camss/camss-vfe.c
index 221abf7bfd47e43e685d4b9a5efc10b066ff8bc2..96ac839663752b9c5164cc35f9fb7f877e67fda7 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.c
+++ b/drivers/media/platform/qcom/camss/camss-vfe.c
@@ -353,6 +353,7 @@ static u32 vfe_src_pad_code(struct vfe_line *line, u32 sink_code,
case CAMSS_8550:
case CAMSS_8650:
case CAMSS_8775P:
+ case CAMSS_HAWI:
case CAMSS_KAANAPALI:
case CAMSS_X1E80100:
switch (sink_code) {
@@ -2021,6 +2022,7 @@ static int vfe_bpl_align_rdi(struct vfe_device *vfe)
case CAMSS_8550:
case CAMSS_8650:
case CAMSS_8775P:
+ case CAMSS_HAWI:
case CAMSS_KAANAPALI:
case CAMSS_X1E80100:
ret = 16;
diff --git a/drivers/media/platform/qcom/camss/camss-vfe.h b/drivers/media/platform/qcom/camss/camss-vfe.h
index 0a91440cfe438625f7f1b71b60186491b3d24d5d..8cc5571e0b91080705c675bb09ff6eb931e6e5fc 100644
--- a/drivers/media/platform/qcom/camss/camss-vfe.h
+++ b/drivers/media/platform/qcom/camss/camss-vfe.h
@@ -252,6 +252,7 @@ extern const struct vfe_hw_ops vfe_ops_340;
extern const struct vfe_hw_ops vfe_ops_480;
extern const struct vfe_hw_ops vfe_ops_680;
extern const struct vfe_hw_ops vfe_ops_1080;
+extern const struct vfe_hw_ops vfe_ops_1190;
extern const struct vfe_hw_ops vfe_ops_gen3;
int vfe_get(struct vfe_device *vfe);
diff --git a/drivers/media/platform/qcom/camss/camss.c b/drivers/media/platform/qcom/camss/camss.c
index df4b4cf30711be62e7403553fbc0f674217fcb56..0a67d4f746eebce0470a1d7648f05b3b76dd356c 100644
--- a/drivers/media/platform/qcom/camss/camss.c
+++ b/drivers/media/platform/qcom/camss/camss.c
@@ -4359,6 +4359,218 @@ static const struct resources_icc icc_res_sa8775p[] = {
},
};
+static const struct camss_subdev_resources vfe_res_hawi[] = {
+ /* VFE0 - TFE Full */
+ {
+ .clock = { "vfe0_fast_ahb", "vfe0", "cpas_vfe0",
+ "camnoc_rt_axi", "camnoc_nrt_axi", "qdss_debug_xo",
+ "cpas_mnoc_hf", "cpas_mnoc_sf" },
+ .clock_rate = { { 0 },
+ { 238200000, 397000000, 440000000, 480000000,
+ 630000000, 750000000, 833000000 },
+ { 0 },
+ { 171428571, 240000000, 300000000, 400000000,
+ 480000000, 600000000 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 0 } },
+ .reg = { "vfe0" },
+ .interrupt = { "vfe0" },
+ .vfe = {
+ .line_num = 3,
+ .has_pd = true,
+ .pd_name = "ife0",
+ .hw_ops = &vfe_ops_1190,
+ .formats_rdi = &vfe_formats_rdi_845,
+ .formats_pix = &vfe_formats_pix_845
+ }
+ },
+ /* VFE1 - TFE Full */
+ {
+ .clock = { "vfe1_fast_ahb", "vfe1", "cpas_vfe1",
+ "camnoc_rt_axi", "camnoc_nrt_axi", "qdss_debug_xo",
+ "cpas_mnoc_hf", "cpas_mnoc_sf" },
+ .clock_rate = { { 0 },
+ { 238200000, 397000000, 440000000, 480000000,
+ 630000000, 750000000, 833000000 },
+ { 0 },
+ { 171428571, 240000000, 300000000, 400000000,
+ 480000000, 600000000 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 0 } },
+ .reg = { "vfe1" },
+ .interrupt = { "vfe1" },
+ .vfe = {
+ .line_num = 3,
+ .has_pd = true,
+ .pd_name = "ife1",
+ .hw_ops = &vfe_ops_1190,
+ .formats_rdi = &vfe_formats_rdi_845,
+ .formats_pix = &vfe_formats_pix_845
+ }
+ },
+ /* VFE2 - TFE Full */
+ {
+ .clock = { "vfe2_fast_ahb", "vfe2", "cpas_vfe2",
+ "camnoc_rt_axi", "camnoc_nrt_axi", "qdss_debug_xo",
+ "cpas_mnoc_hf", "cpas_mnoc_sf" },
+ .clock_rate = { { 0 },
+ { 238200000, 397000000, 440000000, 480000000,
+ 630000000, 750000000, 833000000 },
+ { 0 },
+ { 171428571, 240000000, 300000000, 400000000,
+ 480000000, 600000000 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 0 } },
+ .reg = { "vfe2" },
+ .interrupt = { "vfe2" },
+ .vfe = {
+ .line_num = 3,
+ .has_pd = true,
+ .pd_name = "ife2",
+ .hw_ops = &vfe_ops_1190,
+ .formats_rdi = &vfe_formats_rdi_845,
+ .formats_pix = &vfe_formats_pix_845
+ }
+ },
+ /* VFE3 - IFE Lite */
+ {
+ .clock = { "vfe_lite_ahb", "vfe_lite", "cpas_vfe_lite",
+ "camnoc_rt_axi", "camnoc_nrt_axi", "qdss_debug_xo",
+ "cpas_mnoc_hf", "cpas_mnoc_sf" },
+ .clock_rate = { { 0 },
+ { 200000000, 400000000, 480000000 },
+ { 0 },
+ { 171428571, 240000000, 300000000, 400000000,
+ 480000000, 600000000 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 0 } },
+ .reg = { "vfe_lite0" },
+ .interrupt = { "vfe_lite0" },
+ .vfe = {
+ .line_num = 3,
+ .is_lite = true,
+ .hw_ops = &vfe_ops_1190,
+ .formats_rdi = &vfe_formats_rdi_845,
+ .formats_pix = &vfe_formats_pix_845
+ }
+ },
+ /* VFE4 - IFE Lite */
+ {
+ .clock = { "vfe_lite_ahb", "vfe_lite", "cpas_vfe_lite",
+ "camnoc_rt_axi", "camnoc_nrt_axi", "qdss_debug_xo",
+ "cpas_mnoc_hf", "cpas_mnoc_sf" },
+ .clock_rate = { { 0 },
+ { 200000000, 400000000, 480000000 },
+ { 0 },
+ { 171428571, 240000000, 300000000, 400000000,
+ 480000000, 600000000 },
+ { 0 },
+ { 0 },
+ { 0 },
+ { 0 } },
+ .reg = { "vfe_lite1" },
+ .interrupt = { "vfe_lite1" },
+ .vfe = {
+ .line_num = 3,
+ .is_lite = true,
+ .hw_ops = &vfe_ops_1190,
+ .formats_rdi = &vfe_formats_rdi_845,
+ .formats_pix = &vfe_formats_pix_845
+ }
+ },
+};
+
+static const struct camss_subdev_resources csid_res_hawi[] = {
+ /* CSID0 */
+ {
+ .clock = { "csid", "csid_csiphy_rx" },
+ .clock_rate = { { 480000000 },
+ { 480000000 } },
+ .reg = { "csid0" },
+ .interrupt = { "csid0" },
+ .csid = {
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .hw_ops = &csid_ops_1190,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID1 */
+ {
+ .clock = { "csid", "csid_csiphy_rx" },
+ .clock_rate = { { 480000000 },
+ { 480000000 } },
+ .reg = { "csid1" },
+ .interrupt = { "csid1" },
+ .csid = {
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .hw_ops = &csid_ops_1190,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID2 */
+ {
+ .clock = { "csid", "csid_csiphy_rx" },
+ .clock_rate = { { 480000000 },
+ { 480000000 } },
+ .reg = { "csid2" },
+ .interrupt = { "csid2" },
+ .csid = {
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .hw_ops = &csid_ops_1190,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID_LITE0 */
+ {
+ .clock = { "vfe_lite_csid", "vfe_lite_cphy_rx" },
+ .clock_rate = { { 480000000 },
+ { 480000000 } },
+ .reg = { "csid_lite0" },
+ .interrupt = { "csid_lite0" },
+ .csid = {
+ .is_lite = true,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .hw_ops = &csid_ops_1190,
+ .formats = &csid_formats_gen2
+ }
+ },
+ /* CSID_LITE1 */
+ {
+ .clock = { "vfe_lite_csid", "vfe_lite_cphy_rx" },
+ .clock_rate = { { 480000000 },
+ { 480000000 } },
+ .reg = { "csid_lite1" },
+ .interrupt = { "csid_lite1" },
+ .csid = {
+ .is_lite = true,
+ .parent_dev_ops = &vfe_parent_dev_ops,
+ .hw_ops = &csid_ops_1190,
+ .formats = &csid_formats_gen2
+ }
+ }
+};
+
+static const struct resources_icc icc_res_hawi[] = {
+ {
+ .name = "ahb",
+ .icc_bw_tbl.avg = 38400,
+ .icc_bw_tbl.peak = 76800,
+ },
+ {
+ .name = "hf_mnoc",
+ .icc_bw_tbl.avg = 2097152,
+ .icc_bw_tbl.peak = 2097152,
+ },
+};
+
static const struct camss_subdev_resources csiphy_res_x1e80100[] = {
/* CSIPHY0 */
{
@@ -6078,6 +6290,22 @@ static const struct camss_resources sm8650_resources = {
.vfe_num = ARRAY_SIZE(vfe_res_sm8650),
};
+static const struct camss_resources hawi_resources = {
+ .version = CAMSS_HAWI,
+ .pd_name = "top",
+ .pm_clks = { "cpas_fast_ahb", "cpas_ahb", "gcc_axi_hf" },
+ .csiphy_res = csiphy_res_kaanapali,
+ .tpg_res = tpg_res_x1e80100,
+ .csid_res = csid_res_hawi,
+ .vfe_res = vfe_res_hawi,
+ .icc_res = icc_res_hawi,
+ .icc_path_num = ARRAY_SIZE(icc_res_hawi),
+ .csiphy_num = ARRAY_SIZE(csiphy_res_kaanapali),
+ .tpg_num = ARRAY_SIZE(tpg_res_x1e80100),
+ .csid_num = ARRAY_SIZE(csid_res_hawi),
+ .vfe_num = ARRAY_SIZE(vfe_res_hawi),
+};
+
static const struct camss_resources x1e80100_resources = {
.version = CAMSS_X1E80100,
.pd_name = "top",
@@ -6113,6 +6341,7 @@ static const struct of_device_id camss_dt_match[] = {
{ .compatible = "qcom,sm8250-camss", .data = &sm8250_resources },
{ .compatible = "qcom,sm8550-camss", .data = &sm8550_resources },
{ .compatible = "qcom,sm8650-camss", .data = &sm8650_resources },
+ { .compatible = "qcom,hawi-camss", .data = &hawi_resources },
{ .compatible = "qcom,x1e80100-camss", .data = &x1e80100_resources },
{ .compatible = "qcom,glymur-camss", .data = &x1e80100_resources },
{ }
diff --git a/drivers/media/platform/qcom/camss/camss.h b/drivers/media/platform/qcom/camss/camss.h
index 97fec24e680461a477add23bf5fb0b486903ba5b..95bbf4eb2a63fcd1852716a8d47493f49247c732 100644
--- a/drivers/media/platform/qcom/camss/camss.h
+++ b/drivers/media/platform/qcom/camss/camss.h
@@ -96,6 +96,7 @@ enum camss_version {
CAMSS_8550,
CAMSS_8650,
CAMSS_8775P,
+ CAMSS_HAWI,
CAMSS_KAANAPALI,
CAMSS_X1E80100,
};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili
2026-10-30 12:43 ` [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili Nihal Kumar Gupta
@ 2026-10-30 13:38 ` Loic Poulain
2026-10-30 14:05 ` Hangxiang Ma
0 siblings, 1 reply; 13+ messages in thread
From: Loic Poulain @ 2026-10-30 13:38 UTC (permalink / raw)
To: Nihal Kumar Gupta
Cc: Robert Foss, Andi Shyti, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Bryan O'Donoghue, Vinod Koul, Neil Armstrong,
Manivannan Sadhasivam, Vladimir Zapolskiy, Mauro Carvalho Chehab,
Hangxiang Ma, Bryan O'Donoghue, Suresh Vankadara,
Vikram Sharma, linux-i2c, linux-arm-msm, devicetree, linux-kernel,
linux-phy, linux-media
On Fri, Oct 30, 2026 at 1:43 PM Nihal Kumar Gupta
<nihal.gupta@oss.qualcomm.com> wrote:
>
> From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
>
> Add bindings for Camera Subsystem (CAMSS) on the Qualcomm Hawi platform.
>
> The Hawi platform provides:
> - 6 x CSIPHY (CSI Physical Layer)
> - 3 x TPG (Test Pattern Generator)
> - 3 x CSID (CSI Decoder)
> - 2 x CSID Lite
> - 3 x VFE (Video Front End), 5 RDI per VFE
> - 2 x VFE Lite, 4 RDI per VFE Lite
>
> Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
> Co-developed-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
> Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
> ---
> .../devicetree/bindings/media/qcom,hawi-camss.yaml | 314 +++++++++++++++++++++
> 1 file changed, 314 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml b/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml
> new file mode 100644
> index 0000000000000000000000000000000000000000..32c1cc59e8767b8b03f6947f8fde83d3e7410125
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/qcom,hawi-camss.yaml
> @@ -0,0 +1,314 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/qcom,hawi-camss.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Hawi and Maili Camera Subsystem (CAMSS)
> +
> +maintainers:
> + - Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
> + - Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
> +
> +description:
> + The CAMSS IP is a CSI decoder and ISP present on Qualcomm platforms.
> +
> +properties:
> + compatible:
> + oneOf:
> + - const: qcom,hawi-camss
> + - items:
> + - const: qcom,maili-camss
> + - const: qcom,hawi-camss
> +
> + reg:
> + maxItems: 14
> +
> + reg-names:
> + items:
> + - const: top
> + - const: csid0
> + - const: csid1
> + - const: csid2
> + - const: csid_lite0
> + - const: csid_lite1
> + - const: csitpg0
> + - const: csitpg1
> + - const: csitpg2
> + - const: vfe0
> + - const: vfe1
> + - const: vfe2
> + - const: vfe_lite0
> + - const: vfe_lite1
> +
> + clocks:
> + maxItems: 26
> +
> + clock-names:
> + items:
> + - const: camnoc_nrt_axi
> + - const: camnoc_rt_axi
> + - const: camnoc_dcd_xo
> + - const: cpas_ahb
> + - const: cpas_fast_ahb
> + - const: cpas_mnoc_hf
> + - const: cpas_mnoc_sf
> + - const: cpas_vfe0
> + - const: cpas_vfe1
> + - const: cpas_vfe2
> + - const: cpas_vfe_lite
> + - const: csid
> + - const: csid_csiphy_rx
> + - const: gcc_axi_hf
> + - const: gcc_axi_sf
> + - const: vfe0
> + - const: vfe0_fast_ahb
> + - const: vfe1
> + - const: vfe1_fast_ahb
> + - const: vfe2
> + - const: vfe2_fast_ahb
> + - const: vfe_lite
> + - const: vfe_lite_ahb
> + - const: vfe_lite_cphy_rx
> + - const: vfe_lite_csid
> + - const: qdss_debug_xo
> +
> + interrupts:
> + maxItems: 10
> +
> + interrupt-names:
> + items:
> + - const: csid0
> + - const: csid1
> + - const: csid2
> + - const: csid_lite0
> + - const: csid_lite1
> + - const: vfe0
> + - const: vfe1
> + - const: vfe2
> + - const: vfe_lite0
> + - const: vfe_lite1
> +
> + interconnects:
> + maxItems: 2
> +
> + interconnect-names:
> + items:
> + - const: ahb
> + - const: hf_mnoc
> +
> + iommus:
> + items:
> + - description: S1 HLOS IFE and IFE_LITE non-protected stream
> +
> + power-domains:
> + items:
> + - description: IFE0 GDSC - Global Distributed Switch Controller for IFE0.
> + - description: IFE1 GDSC - Global Distributed Switch Controller for IFE1.
> + - description: IFE2 GDSC - Global Distributed Switch Controller for IFE2.
> + - description: Titan GDSC - Global Distributed Switch Controller for the entire camss.
> +
> + power-domain-names:
> + items:
> + - const: ife0
> + - const: ife1
> + - const: ife2
> + - const: top
> +
> + ports:
> + $ref: /schemas/graph.yaml#/properties/ports
> +
> + description:
> + CSI input ports.
> +
> + patternProperties:
> + "^port@[0-5]$":
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + unevaluatedProperties: false
> + description:
> + Input ports for receiving CSI data on CSIPHY 0-5.
> +
> + properties:
> + endpoint:
> + $ref: video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + properties:
> + data-lanes:
> + minItems: 1
> + maxItems: 4
> +
> + bus-type:
> + enum:
> + - 1 # MEDIA_BUS_TYPE_CSI2_CPHY
> + - 4 # MEDIA_BUS_TYPE_CSI2_DPHY
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - clocks
> + - clock-names
> + - interrupts
> + - interrupt-names
> + - interconnects
> + - interconnect-names
> + - iommus
> + - power-domains
> + - power-domain-names
> + - ports
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/qcom,hawi-gcc.h>
> + #include <dt-bindings/clock/qcom,hawi-camcc.h>
> + #include <dt-bindings/interconnect/qcom,icc.h>
> + #include <dt-bindings/interconnect/qcom,hawi-rpmh.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/power/qcom,rpmhpd.h>
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + isp@9253000 {
Address should match your first reg addr.
> + compatible = "qcom,hawi-camss";
> +
> + reg = <0x0 0x0900b000 0x0 0x1000>,
> + <0x0 0x09253000 0x0 0x5e80>,
> + <0x0 0x09263000 0x0 0x5e80>,
> + <0x0 0x09273000 0x0 0x5e80>,
> + <0x0 0x092d3000 0x0 0x3880>,
> + <0x0 0x092e7000 0x0 0x3880>,
> + <0x0 0x093fd000 0x0 0x400>,
> + <0x0 0x093fe000 0x0 0x400>,
> + <0x0 0x093ff000 0x0 0x400>,
> + <0x0 0x09151000 0x0 0x20000>,
> + <0x0 0x09171000 0x0 0x20000>,
> + <0x0 0x09191000 0x0 0x20000>,
> + <0x0 0x092dc000 0x0 0x6800>,
> + <0x0 0x092f0000 0x0 0x6800>;
> + reg-names = "top",
> + "csid0",
> + "csid1",
> + "csid2",
> + "csid_lite0",
> + "csid_lite1",
> + "csitpg0",
> + "csitpg1",
> + "csitpg2",
> + "vfe0",
> + "vfe1",
> + "vfe2",
> + "vfe_lite0",
> + "vfe_lite1";
> +
> + clocks = <&camcc CAM_CC_CAMNOC_NRT_AXI_CLK>,
> + <&camcc CAM_CC_CAMNOC_RT_AXI_CLK>,
> + <&camcc CAM_CC_CAMNOC_DCD_XO_CLK>,
> + <&camcc CAM_CC_CAM_TOP_AHB_CLK>,
> + <&camcc CAM_CC_CAM_TOP_FAST_AHB_CLK>,
> + <&camcc CAM_CC_TITAN_MNOC_HF_CLK>,
> + <&camcc CAM_CC_TITAN_MNOC_SF_CLK>,
> + <&camcc CAM_CC_CAMNOC_RT_TFE_0_MAIN_CLK>,
> + <&camcc CAM_CC_CAMNOC_RT_TFE_1_MAIN_CLK>,
> + <&camcc CAM_CC_CAMNOC_RT_TFE_2_MAIN_CLK>,
> + <&camcc CAM_CC_CAMNOC_RT_IFE_LITE_CLK>,
> + <&camcc CAM_CC_CSID_CLK>,
> + <&camcc CAM_CC_CSID_CSIPHY_RX_CLK>,
> + <&gcc GCC_CAMERA_HF_AXI_CLK>,
> + <&gcc GCC_CAMERA_SF_AXI_CLK>,
> + <&camcc CAM_CC_TFE_0_MAIN_CLK>,
> + <&camcc CAM_CC_TFE_0_MAIN_FAST_AHB_CLK>,
> + <&camcc CAM_CC_TFE_1_MAIN_CLK>,
> + <&camcc CAM_CC_TFE_1_MAIN_FAST_AHB_CLK>,
> + <&camcc CAM_CC_TFE_2_MAIN_CLK>,
> + <&camcc CAM_CC_TFE_2_MAIN_FAST_AHB_CLK>,
> + <&camcc CAM_CC_IFE_LITE_CLK>,
> + <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
> + <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
> + <&camcc CAM_CC_IFE_LITE_CSID_CLK>,
> + <&camcc CAM_CC_QDSS_DEBUG_XO_CLK>;
> + clock-names = "camnoc_nrt_axi",
> + "camnoc_rt_axi",
> + "camnoc_dcd_xo",
> + "cpas_ahb",
> + "cpas_fast_ahb",
> + "cpas_mnoc_hf",
> + "cpas_mnoc_sf",
> + "cpas_vfe0",
> + "cpas_vfe1",
> + "cpas_vfe2",
> + "cpas_vfe_lite",
> + "csid",
> + "csid_csiphy_rx",
> + "gcc_axi_hf",
> + "gcc_axi_sf",
> + "vfe0",
> + "vfe0_fast_ahb",
> + "vfe1",
> + "vfe1_fast_ahb",
> + "vfe2",
> + "vfe2_fast_ahb",
> + "vfe_lite",
> + "vfe_lite_ahb",
> + "vfe_lite_cphy_rx",
> + "vfe_lite_csid",
> + "qdss_debug_xo";
> +
> + interrupts = <GIC_SPI 601 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 603 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 605 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 433 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 436 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 457 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 606 IRQ_TYPE_EDGE_RISING>,
> + <GIC_SPI 377 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "csid0",
> + "csid1",
> + "csid2",
> + "csid_lite0",
> + "csid_lite1",
> + "vfe0",
> + "vfe1",
> + "vfe2",
> + "vfe_lite0",
> + "vfe_lite1";
> +
> + interconnects = <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
> + &config_noc SLAVE_CAMERA_CFG QCOM_ICC_TAG_ACTIVE_ONLY>,
> + <&mmss_noc MASTER_CAMNOC_HF QCOM_ICC_TAG_ALWAYS
> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
> + interconnect-names = "ahb",
> + "hf_mnoc";
> +
> + iommus = <&apps_smmu 0x1800 0x00>;
> +
> + power-domains = <&camcc CAM_CC_TFE_0_GDSC>,
> + <&camcc CAM_CC_TFE_1_GDSC>,
> + <&camcc CAM_CC_TFE_2_GDSC>,
> + <&camcc CAM_CC_TITAN_TOP_GDSC>;
> + power-domain-names = "ife0",
> + "ife1",
> + "ife2",
> + "top";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + camss_csiphy0_ep: endpoint {
> + data-lanes = <1 2 3 4>;
> + remote-endpoint = <&csiphy0_out>;
> + };
> + };
> + };
> + };
> + };
>
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support
2026-10-30 12:43 ` [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support Nihal Kumar Gupta
@ 2026-10-30 13:39 ` Loic Poulain
0 siblings, 0 replies; 13+ messages in thread
From: Loic Poulain @ 2026-10-30 13:39 UTC (permalink / raw)
To: Nihal Kumar Gupta
Cc: Robert Foss, Andi Shyti, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Bryan O'Donoghue, Vinod Koul, Neil Armstrong,
Manivannan Sadhasivam, Vladimir Zapolskiy, Mauro Carvalho Chehab,
Hangxiang Ma, Bryan O'Donoghue, Suresh Vankadara,
Vikram Sharma, linux-i2c, linux-arm-msm, devicetree, linux-kernel,
linux-phy, linux-media
On Fri, Oct 30, 2026 at 1:43 PM Nihal Kumar Gupta
<nihal.gupta@oss.qualcomm.com> wrote:
>
> From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
>
> Add support for the Hawi 2nm CSI-2 D-PHY.
>
> Reuse the Kaanapali lane table and adjust the data-lane CTRL0 value
> from 0x8e to 0x8c for Hawi-specific tuning. This prevents potential
> stream stalls and SMMU faults.
>
> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
> Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
Reviewed-by: Loic Poulain <loic.poulain@oss.qualcomm.com>
> ---
> drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c | 136 +++++++++++++++++++++
> drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c | 1 +
> drivers/phy/qualcomm/phy-qcom-mipi-csi2.h | 1 +
> 3 files changed, 138 insertions(+)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
> index 658a39463104bedfa31d0ccb81fd9d34017e91a6..1e9bb8b9e50bb15e7fad3c6e3d6048bf049e3e64 100644
> --- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
> +++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-3ph-dphy.c
> @@ -162,6 +162,126 @@ mipi_csi2phy_lane_regs lane_regs_x1e80100[] = {
> {.reg_addr = 0x0c64, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL},
> };
>
> +/* 2nm 2PH 2p5Gbps 4 lane DPHY mode, Kaanapali table with data-lane CTRL0 0x8c */
> +static const struct mipi_csi2phy_lane_regs lane_regs_hawi[] = {
> + /* Power up lanes in 2ph mode. */
> + { .reg_addr = 0x101c, .reg_data = 0x7a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x1018, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> +
> + { .reg_addr = 0x0094, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x00a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0090, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0098, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0094, .reg_data = 0x07, .delay_us = 1,
> + .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0030, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0000, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0038, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x002c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0034, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x001c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0014, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x003c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0004, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0020, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0008, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
> + { .reg_addr = 0x0010, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0094, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x005c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0060, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0064, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
> +
> + { .reg_addr = 0x0e94, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0ea0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e90, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e98, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e94, .reg_data = 0x07, .delay_us = 1,
> + .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e30, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e28, .reg_data = 0x04, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e00, .reg_data = 0x80, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e0c, .reg_data = 0xff, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e38, .reg_data = 0x1f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e2c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e34, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e1c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e14, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e3c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e04, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e20, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0e08, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
> + { .reg_addr = 0x0e10, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
> +
> + { .reg_addr = 0x0494, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x04a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0490, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0498, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0494, .reg_data = 0x07, .delay_us = 1,
> + .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0430, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0400, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0438, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x042c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0434, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x041c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0414, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x043c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0404, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0420, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0408, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
> + { .reg_addr = 0x0410, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0494, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x045c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0460, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0464, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
> +
> + { .reg_addr = 0x0894, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x08a0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0890, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0898, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0894, .reg_data = 0x07, .delay_us = 1,
> + .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0830, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0800, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0838, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x082c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0834, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x081c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0814, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x083c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0804, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0820, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0808, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
> + { .reg_addr = 0x0810, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0894, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x085c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0860, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0864, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
> +
> + { .reg_addr = 0x0c94, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0ca0, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c90, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c98, .reg_data = 0x08, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c94, .reg_data = 0x07, .delay_us = 1,
> + .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c30, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c00, .reg_data = 0x8c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c38, .reg_data = 0xfe, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c2c, .reg_data = 0x01, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c34, .reg_data = 0x0f, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c1c, .reg_data = 0x0a, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c14, .reg_data = 0x60, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c3c, .reg_data = 0xb8, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c04, .reg_data = 0x0c, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c20, .reg_data = 0x00, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c08, .reg_data = 0x10, .param_type = CSIPHY_SETTLE_CNT_LOWER_BYTE },
> + { .reg_addr = 0x0c10, .reg_data = 0x52, .param_type = CSIPHY_DEFAULT_PARAMS },
> + { .reg_addr = 0x0c94, .reg_data = 0xd7, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0c5c, .reg_data = 0x00, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0c60, .reg_data = 0xbd, .param_type = CSIPHY_SKEW_CAL },
> + { .reg_addr = 0x0c64, .reg_data = 0x7f, .param_type = CSIPHY_SKEW_CAL },
> +};
> +
> static inline const struct mipi_csi2phy_device_regs *
> csi2phy_dev_to_regs(struct mipi_csi2phy_device *csi2phy)
> {
> @@ -405,3 +525,19 @@ const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_3nm_kaanapali = {
> .genpds = x1e_genpds,
> .num_genpds = ARRAY_SIZE(x1e_genpds),
> };
> +
> +const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_2nm_hawi = {
> + .ops = &phy_qcom_mipi_csi2_ops_3ph_1_0,
> + .reg_info = {
> + .init_seq = lane_regs_hawi,
> + .lane_array_size = ARRAY_SIZE(lane_regs_hawi),
> + .common_regs_offset = 0x1000,
> + .common_status_offset = 0x138,
> + },
> + .supply_names = (const char **)x1e_supplies,
> + .num_supplies = ARRAY_SIZE(x1e_supplies),
> + .clk_names = (const char **)x1e_clks,
> + .num_clk = ARRAY_SIZE(x1e_clks),
> + .genpds = x1e_genpds,
> + .num_genpds = ARRAY_SIZE(x1e_genpds),
> +};
> diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
> index aff9e66f0352e1d4d7a07d10d350ea2cba6df233..76c55f8e30b8c629818762d0b42a7dc4ddc6716b 100644
> --- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
> +++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2-core.c
> @@ -445,6 +445,7 @@ static int phy_qcom_mipi_csi2_probe(struct platform_device *pdev)
> static const struct of_device_id phy_qcom_mipi_csi2_of_match_table[] = {
> { .compatible = "qcom,x1e80100-csi2-phy", .data = &mipi_csi2_dphy_4nm_x1e },
> { .compatible = "qcom,kaanapali-csi2-phy", .data = &mipi_csi2_dphy_3nm_kaanapali },
> + { .compatible = "qcom,hawi-csi2-phy", .data = &mipi_csi2_dphy_2nm_hawi },
> { }
> };
> MODULE_DEVICE_TABLE(of, phy_qcom_mipi_csi2_of_match_table);
> diff --git a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
> index 2355a1db9b941469325646ef81d0f70c6a2badc4..4ad058b916ebba8b319cb297c231cba10d3ec602 100644
> --- a/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
> +++ b/drivers/phy/qualcomm/phy-qcom-mipi-csi2.h
> @@ -95,5 +95,6 @@ struct mipi_csi2phy_device {
>
> extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_4nm_x1e;
> extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_3nm_kaanapali;
> +extern const struct mipi_csi2phy_soc_cfg mipi_csi2_dphy_2nm_hawi;
>
> #endif /* __PHY_QCOM_MIPI_CSI2_H__ */
>
> --
> 2.34.1
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili
2026-10-30 13:38 ` Loic Poulain
@ 2026-10-30 14:05 ` Hangxiang Ma
0 siblings, 0 replies; 13+ messages in thread
From: Hangxiang Ma @ 2026-10-30 14:05 UTC (permalink / raw)
To: Loic Poulain, Nihal Kumar Gupta
Cc: Robert Foss, Andi Shyti, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Bryan O'Donoghue, Vinod Koul, Neil Armstrong,
Manivannan Sadhasivam, Vladimir Zapolskiy, Mauro Carvalho Chehab,
Bryan O'Donoghue, Suresh Vankadara, Vikram Sharma, linux-i2c,
linux-arm-msm, devicetree, linux-kernel, linux-phy, linux-media
On 10/30/2026 9:38 PM, Loic Poulain wrote:
> On Fri, Oct 30, 2026 at 1:43 PM Nihal Kumar Gupta
> <nihal.gupta@oss.qualcomm.com> wrote:
>>
>> From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
>>
>> Add bindings for Camera Subsystem (CAMSS) on the Qualcomm Hawi platform.
>>
>> The Hawi platform provides:
>> - 6 x CSIPHY (CSI Physical Layer)
>> - 3 x TPG (Test Pattern Generator)
>> - 3 x CSID (CSI Decoder)
>> - 2 x CSID Lite
>> - 3 x VFE (Video Front End), 5 RDI per VFE
>> - 2 x VFE Lite, 4 RDI per VFE Lite
>>
>> Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
>> Co-developed-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
>> Signed-off-by: Nihal Kumar Gupta <nihal.gupta@oss.qualcomm.com>
[...]
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/qcom,hawi-gcc.h>
>> + #include <dt-bindings/clock/qcom,hawi-camcc.h>
>> + #include <dt-bindings/interconnect/qcom,icc.h>
>> + #include <dt-bindings/interconnect/qcom,hawi-rpmh.h>
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/power/qcom,rpmhpd.h>
>> +
>> + soc {
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>> +
>> + isp@9253000 {
>
> Address should match your first reg addr.
>
Ack, thanks. Missed updating the binding accordingly. Will fix it in the
next revision.
---
Best Regards,
Hangxiang
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 5/5] media: qcom: camss: Add support for Hawi
2026-10-30 12:43 ` [PATCH v3 5/5] media: qcom: camss: Add support for Hawi Nihal Kumar Gupta
@ 2026-10-30 15:04 ` Bryan O'Donoghue
2026-10-30 15:25 ` Hangxiang Ma
2026-10-30 15:05 ` Bryan O'Donoghue
1 sibling, 1 reply; 13+ messages in thread
From: Bryan O'Donoghue @ 2026-10-30 15:04 UTC (permalink / raw)
To: Nihal Kumar Gupta, Loic Poulain, Robert Foss, Andi Shyti,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Vinod Koul,
Neil Armstrong, Manivannan Sadhasivam, Vladimir Zapolskiy,
Mauro Carvalho Chehab, Hangxiang Ma, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
On 30/10/2026 12:43, Nihal Kumar Gupta wrote:
> +static const struct camss_subdev_resources csid_res_hawi[] = {
> + /* CSID0 */
> + {
> + .clock = { "csid", "csid_csiphy_rx" },
> + .clock_rate = { { 480000000 },
> + { 480000000 } },
> + .reg = { "csid0" },
> + .interrupt = { "csid0" },
> + .csid = {
> + .parent_dev_ops = &vfe_parent_dev_ops,
> + .hw_ops = &csid_ops_1190,
> + .formats = &csid_formats_gen2
> + }
This looks strange, why is there only one clock rate ?
---
bod
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 5/5] media: qcom: camss: Add support for Hawi
2026-10-30 12:43 ` [PATCH v3 5/5] media: qcom: camss: Add support for Hawi Nihal Kumar Gupta
2026-10-30 15:04 ` Bryan O'Donoghue
@ 2026-10-30 15:05 ` Bryan O'Donoghue
2026-10-30 15:29 ` Hangxiang Ma
1 sibling, 1 reply; 13+ messages in thread
From: Bryan O'Donoghue @ 2026-10-30 15:05 UTC (permalink / raw)
To: Nihal Kumar Gupta, Loic Poulain, Robert Foss, Andi Shyti,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Vinod Koul,
Neil Armstrong, Manivannan Sadhasivam, Vladimir Zapolskiy,
Mauro Carvalho Chehab, Hangxiang Ma, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
On 30/10/2026 12:43, Nihal Kumar Gupta wrote:
> @@ -6113,6 +6341,7 @@ static const struct of_device_id camss_dt_match[] = {
> { .compatible = "qcom,sm8250-camss", .data = &sm8250_resources },
> { .compatible = "qcom,sm8550-camss", .data = &sm8550_resources },
> { .compatible = "qcom,sm8650-camss", .data = &sm8650_resources },
> + { .compatible = "qcom,hawi-camss", .data = &hawi_resources },
> { .compatible = "qcom,x1e80100-camss", .data = &x1e80100_resources },
> { .compatible = "qcom,glymur-camss", .data = &x1e80100_resources },
this insertion makes no sense.
In fact glymur should have gone up the top with hawi underneath it.
Could you please remediate ?
---
bod
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 5/5] media: qcom: camss: Add support for Hawi
2026-10-30 15:04 ` Bryan O'Donoghue
@ 2026-10-30 15:25 ` Hangxiang Ma
0 siblings, 0 replies; 13+ messages in thread
From: Hangxiang Ma @ 2026-10-30 15:25 UTC (permalink / raw)
To: Bryan O'Donoghue, Nihal Kumar Gupta, Loic Poulain,
Robert Foss, Andi Shyti, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
On 10/30/2026 11:04 PM, Bryan O'Donoghue wrote:
> On 30/10/2026 12:43, Nihal Kumar Gupta wrote:
>> +static const struct camss_subdev_resources csid_res_hawi[] = {
>> + /* CSID0 */
>> + {
>> + .clock = { "csid", "csid_csiphy_rx" },
>> + .clock_rate = { { 480000000 },
>> + { 480000000 } },
>> + .reg = { "csid0" },
>> + .interrupt = { "csid0" },
>> + .csid = {
>> + .parent_dev_ops = &vfe_parent_dev_ops,
>> + .hw_ops = &csid_ops_1190,
>> + .formats = &csid_formats_gen2
>> + }
>
> This looks strange, why is there only one clock rate ?
>
> ---
> bod
Hi Bryan, the current CAMSS CSID code always selects the first frequency
listed for each clock in the CAMSS resource table.
In camss-csid.c:
[...]
} else if (clock->nfreqs) {
clk_set_rate(clock->clk, clock->freq[0]);
}
[...]
For the CSID and CSID_CSIPHY_RX clocks, the hardware supports three
clock rates: 200 MHz, 300 MHz, and 480 MHz. If I remember correctly,
200MHz and 300 MHz is not sufficient for the sensor's output pixel rate,
so we need to use the highest rate, 480 MHz, to meet the bandwidth
requirement. Thanks a lot.
---
Best Regards,
Hangxiang
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v3 5/5] media: qcom: camss: Add support for Hawi
2026-10-30 15:05 ` Bryan O'Donoghue
@ 2026-10-30 15:29 ` Hangxiang Ma
0 siblings, 0 replies; 13+ messages in thread
From: Hangxiang Ma @ 2026-10-30 15:29 UTC (permalink / raw)
To: Bryan O'Donoghue, Nihal Kumar Gupta, Loic Poulain,
Robert Foss, Andi Shyti, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Vinod Koul, Neil Armstrong, Manivannan Sadhasivam,
Vladimir Zapolskiy, Mauro Carvalho Chehab, Bryan O'Donoghue
Cc: Suresh Vankadara, Vikram Sharma, linux-i2c, linux-arm-msm,
devicetree, linux-kernel, linux-phy, linux-media
On 10/30/2026 11:05 PM, Bryan O'Donoghue wrote:
> On 30/10/2026 12:43, Nihal Kumar Gupta wrote:
>> @@ -6113,6 +6341,7 @@ static const struct of_device_id
>> camss_dt_match[] = {
>> { .compatible = "qcom,sm8250-camss", .data = &sm8250_resources },
>> { .compatible = "qcom,sm8550-camss", .data = &sm8550_resources },
>> { .compatible = "qcom,sm8650-camss", .data = &sm8650_resources },
>> + { .compatible = "qcom,hawi-camss", .data = &hawi_resources },
>> { .compatible = "qcom,x1e80100-camss", .data =
>> &x1e80100_resources },
>> { .compatible = "qcom,glymur-camss", .data = &x1e80100_resources },
>
> this insertion makes no sense.
>
> In fact glymur should have gone up the top with hawi underneath it.
>
> Could you please remediate ?
>
> ---
> bod
ACK. Thanks for pointing this out.
The compatible order should be checked carefully going forward. We will
correct the order and make sure Glymur is placed above Hawi.
---
Best Regards,
Hangxiang
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2026-10-30 15:29 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-10-30 12:43 [PATCH v3 0/5] Add CAMSS support for Qualcomm Hawi and Maili Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 1/5] dt-bindings: i2c: qcom,i2c-cci: Add Hawi compatible Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 2/5] dt-bindings: phy: qcom,x1e80100-csi2-phy: Add Hawi and Maili compatibles Nihal Kumar Gupta
2026-10-30 12:43 ` [PATCH v3 3/5] dt-bindings: media: Add CAMSS device for Hawi and Maili Nihal Kumar Gupta
2026-10-30 13:38 ` Loic Poulain
2026-10-30 14:05 ` Hangxiang Ma
2026-10-30 12:43 ` [PATCH v3 4/5] phy: qcom-mipi-csi2: Add Hawi support Nihal Kumar Gupta
2026-10-30 13:39 ` Loic Poulain
2026-10-30 12:43 ` [PATCH v3 5/5] media: qcom: camss: Add support for Hawi Nihal Kumar Gupta
2026-10-30 15:04 ` Bryan O'Donoghue
2026-10-30 15:25 ` Hangxiang Ma
2026-10-30 15:05 ` Bryan O'Donoghue
2026-10-30 15:29 ` Hangxiang Ma
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox