Re: [PATCH v2 Resent 6/6] i3c: master: svc: fix random hot join failure since timeout error

[Miquel Raynal <miquel.raynal@bootlin.com>]

Hi Frank,

Frank.li@nxp.com wrote on Fri, 20 Oct 2023 11:17:17 -0400:

> On Fri, Oct 20, 2023 at 10:47:52AM -0400, Frank Li wrote:
> > On Fri, Oct 20, 2023 at 04:35:25PM +0200, Miquel Raynal wrote:  
> > > Hi Frank,
> > > 
> > > Frank.li@nxp.com wrote on Fri, 20 Oct 2023 10:18:55 -0400:
> > >   
> > > > On Fri, Oct 20, 2023 at 04:06:45PM +0200, Miquel Raynal wrote:  
> > > > > Hi Frank,
> > > > > 
> > > > > Frank.li@nxp.com wrote on Thu, 19 Oct 2023 11:39:42 -0400:
> > > > >     
> > > > > > On Thu, Oct 19, 2023 at 08:44:52AM +0200, Miquel Raynal wrote:    
> > > > > > > Hi Frank,
> > > > > > > 
> > > > > > > Frank.Li@nxp.com wrote on Wed, 18 Oct 2023 11:59:26 -0400:
> > > > > > >       
> > > > > > > > master side report:
> > > > > > > >   silvaco-i3c-master 44330000.i3c-master: Error condition: MSTATUS 0x020090c7, MERRWARN 0x00100000
> > > > > > > > 
> > > > > > > > BIT 20: TIMEOUT error
> > > > > > > >   The module has stalled too long in a frame. This happens when:
> > > > > > > >   - The TX FIFO or RX FIFO is not handled and the bus is stuck in the
> > > > > > > > middle of a message,
> > > > > > > >   - No STOP was issued and between messages,
> > > > > > > >   - IBI manual is used and no decision was made.      
> > > > > > > 
> > > > > > > I am still not convinced this should be ignored in all cases.
> > > > > > > 
> > > > > > > Case 1 is a problem because the hardware failed somehow.      
> > > > > > 
> > > > > > But so far, no action to handle this case in current code.    
> > > > > 
> > > > > Yes, but if you detect an issue and ignore it, it's not better than
> > > > > reporting it without handling it. Instead of totally ignoring this I
> > > > > would at least write a debug message (identical to what's below) before
> > > > > returning false, even though I am not convinced unconditionally
> > > > > returning false here is wise. If you fail a hardware sequence because
> > > > > you added a printk, it's a problem. Maybe you consider this line as
> > > > > noise, but I believe it's still an error condition. Maybe, however,
> > > > > this bit gets set after the whole sequence, and this is just a "bus
> > > > > is idle" condition. If that's the case, then you need some
> > > > > additional heuristics to properly ignore the bit?
> > > > >     
> > > > 
> > > >                 dev_err(master->dev,                                       
> > > >                         "Error condition: MSTATUS 0x%08x, MERRWARN 0x%08x\n",
> > > >                         mstatus, merrwarn);
> > > > +
> > > > +		/* ignore timeout error */
> > > > +		if (merrwarn & SVC_I3C_MERRWARN_TIMEOUT)
> > > > +			return false;
> > > > +
> > > > 
> > > > Is it okay move SVC_I3C_MERRWARN_TIMEOUT after dev_err?  
> > > 
> > > I think you mentioned earlier that the problem was not the printk but
> > > the return value. So perhaps there is a way to know if the timeout
> > > happened after a transaction and was legitimate or not?  
> > 
> > Error message just annoise user, don't impact function. But return false
> > let IBI thread running to avoid dead lock.   
> 
> I forget mention one thing. Any error message here will make SDA low for
> longer.  Before emit stop, SDA is low.
> 
> I have not checked I3C spec yet about how long SDA will be allowed. it will
> worser if message go through uart port. The bus will be locked longer.
> 
> It's better to print error message after emit_stop to reduce SDA low time.

That's fine I guess.

Thanks,
Miquèl

-- 
linux-i3c mailing list
linux-i3c@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-i3c