RE: As of 2.6.13-rc1 Fusion-MPT very slow

RE: As of 2.6.13-rc1 Fusion-MPT very slow

[tony.luck]

This is alive and well in 2.6.13 (final) on ia64.  Excerpts from dmesg
when booting:

Fusion MPT base driver 3.03.02
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.02
GSI 28 (level, low) -> CPU 1 (0xc218) vector 49
ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 28 (level, low) -> IRQ 49
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
scsi0 : ioc0: LSI53C1030, FwRev\x01030a00h, Ports=1, MaxQ%5, IRQI
  Vendor: QUANTUM   Model: ATLAS IV 9 SCA    Rev: 0B0B
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 17942584 512-byte hdwr sectors (9187 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 17942584 512-byte hdwr sectors (9187 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
  Vendor: MAXTOR    Model: ATLAS10K4_73SCA   Rev: DFV0
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 143666192 512-byte hdwr sectors (73557 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
  Vendor: ESG-SHV   Model: SCA HSBP M17      Rev: 1.0D
  Type:   Processor                          ANSI SCSI revision: 02
GSI 29 (level, low) -> CPU 2 (0xc418) vector 50
ACPI: PCI Interrupt 0000:06:02.1[B] -> GSI 29 (level, low) -> IRQ 50
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator}
scsi1 : ioc1: LSI53C1030, FwRev\x01030a00h, Ports=1, MaxQ%5, IRQP
Fusion MPT FC Host driver 3.03.02
Fusion MPT misc device (ioctl) driver 3.03.02
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor\x10,220)


When I'm up and running, measure the speed of sda and sdb:

# hdparm -t /dev/sda

/dev/sda:
 Timing buffered disk reads:   62 MB in  3.02 seconds =  20.56 MB/sec

[This is VERY consistent from run to run, 20.56 MB/s every time].

# hdparm -t /dev/sdb

/dev/sdb:
 Timing buffered disk reads:    2 MB in  4.04 seconds = 53.79 kB/sec

[Speed on sdb is very erratic ... 53.79 KB/s is the worst I saw in half
a dozen tests ... but first try after boot was 47.14 MB/s, and I see
intermediate rates all over the map: 545.42 KB/s, 5.13 MB/s, 32.61 MB/s]

dmesg shows some messages like this:
mptscsih: ioc0: >> Attempting task abort! (scà000001fceb4c80)
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc0: >> Attempting task abort! (scà000001fceb5080)
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc0: >> Attempting task abort! (scà000001fceb6e80)
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc0: >> Attempting task abort! (scà000001fceb7a80)
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated

Sometimes there are floods of these, other times just a few ... e.g. I
saw just those 8 lines after ten iterations of "hdparm -t /dev/hdb".

-Tony

RE: As of 2.6.13-rc1 Fusion-MPT very slow

[tony.luck]

> This is alive and well in 2.6.13 (final) on ia64.

Or perhaps not.  When I went into the machine room to take
a look at this machine, I found that the disk drive in
question was making some very bad noises.  A few minutes
later it stopped responding at all.

Putting in a new drive, I see a consistent 51 MB/s on /dev/sdb

Sorry for the noise.

-Tony