Re: PROBLEM: (libata) cdrom drive not detected in -mm series

Linux ATA/IDE development
 help / color / mirror / Atom feed

* Re: PROBLEM: (libata) cdrom drive not detected in -mm series
       [not found] <9bfa9ae0609111802o9131e8bg6c5d394ad87b16ea@mail.gmail.com>
@ 2006-09-12  7:41 ` Tejun Heo
  2006-09-12 11:30   ` Nelson A. de Oliveira
  0 siblings, 1 reply; 5+ messages in thread
From: Tejun Heo @ 2006-09-12  7:41 UTC (permalink / raw)
  To: Nelson A. de Oliveira
  Cc: linux-kernel, Andrew Morton, Jeff Garzik,
	linux-ide@vger.kernel.org

[-- Attachment #1: Type: text/plain, Size: 661 bytes --]

Nelson A. de Oliveira wrote:
> Hi!
> 
> My USB CD-ROM drive (that is detected as a SCSI drive) is not being
> detected on the -mm series of the Kernel.

s/USB/SATA/, I presume.

[--snip--]
-ata2.00: ATAPI, max UDMA/33
-ata2.00: configured for UDMA/33
-  Vendor: HL-DT-ST  Model: CDRW/DVD GCC4244  Rev: B101
-  Type:   CD-ROM                             ANSI SCSI revision: 05

Argh... yet another PCS problem.  With whole -mm applied, does adding 
kernel parameter 'ata_piix.force_pcs=1' make any difference?

Please provide the following info.

* the result of 'lspci -nvvv'

* dmesg output with the attached patch applied (on top of -mm).

Thanks.

-- 
tejun

[-- Attachment #2: patch --]
[-- Type: text/plain, Size: 737 bytes --]

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
index 22b2dba..53a19fd 100644
--- a/drivers/ata/ata_piix.c
+++ b/drivers/ata/ata_piix.c
@@ -560,7 +560,7 @@ static unsigned int piix_sata_present_ma
 	u16 pcs;
 
 	pci_read_config_word(pdev, ICH5_PCS, &pcs);
-	DPRINTK("ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
+	printk(KERN_INFO "ata%u: ENTER, pcs=0x%x base=%d\n", ap->id, pcs, base);
 
 	for (i = 0; i < 2; i++) {
 		port = map[base + i];
@@ -571,7 +571,7 @@ static unsigned int piix_sata_present_ma
 			present_mask |= 1 << i;
 	}
 
-	DPRINTK("ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
+	printk(KERN_INFO "ata%u: LEAVE, pcs=0x%x present_mask=0x%x\n",
 		ap->id, pcs, present_mask);
 
 	return present_mask;

^ permalink raw reply related	[flat|nested] 5+ messages in thread

* Re: PROBLEM: (libata) cdrom drive not detected in -mm series
  2006-09-12  7:41 ` PROBLEM: (libata) cdrom drive not detected in -mm series Tejun Heo
@ 2006-09-12 11:30   ` Nelson A. de Oliveira
  2006-09-13 13:37     ` Tejun Heo
  0 siblings, 1 reply; 5+ messages in thread
From: Nelson A. de Oliveira @ 2006-09-12 11:30 UTC (permalink / raw)
  To: Tejun Heo
  Cc: linux-kernel, Andrew Morton, Jeff Garzik,
	linux-ide@vger.kernel.org

[-- Attachment #1: Type: text/plain, Size: 883 bytes --]

Hi!

On 9/12/06, Tejun Heo <htejun@gmail.com> wrote:
> Nelson A. de Oliveira wrote:
> > My USB CD-ROM drive (that is detected as a SCSI drive) is not being
> > detected on the -mm series of the Kernel.
>
> s/USB/SATA/, I presume.

Yes, sorry!

> [--snip--]
> -ata2.00: ATAPI, max UDMA/33
> -ata2.00: configured for UDMA/33
> -  Vendor: HL-DT-ST  Model: CDRW/DVD GCC4244  Rev: B101
> -  Type:   CD-ROM                             ANSI SCSI revision: 05
>
> Argh... yet another PCS problem.  With whole -mm applied, does adding
> kernel parameter 'ata_piix.force_pcs=1' make any difference?

No. Tried with latest 2.6.18-rc6-mm2 and still not detected.

> Please provide the following info.
>
> * the result of 'lspci -nvvv'
>
> * dmesg output with the attached patch applied (on top of -mm).

Applied the patch and sending the output of lspci and dmesg.

Thank you very much!

Nelson

[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 18440 bytes --]

Linux version 2.6.18-rc6-mm2 (root@orthrus) (gcc version 4.2.0 20060905 (experimental) (Debian 4.2-20060905-1)) #1 SMP PREEMPT Tue Sep 12 08:17:00 BRT 2006
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001f5d3400 end: 000000001f6d3400 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001f6d3400 size: 000000000092cc00 end: 0000000020000000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010007000 end: 00000000f0007000 type: 2
copy_e820_map() start: 00000000f0008000 size: 0000000000004000 end: 00000000f000c000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000080000 end: 00000000feda0000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000010000 end: 00000000fee10000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f6d3400 (usable)
 BIOS-e820: 000000001f6d3400 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
502MB LOWMEM available.
Entering add_active_range(0, 0, 128723) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   128723
early_node_map[1] active PFN ranges
    0:        0 ->   128723
On node 0 totalpages: 128723
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 973 pages used for memmap
  Normal zone: 123654 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 DELL                                  ) @ 0x000fc390
ACPI: RSDT (v001 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d3a96
ACPI: FADT (v001 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d4800
ACPI: MADT (v001 DELL    M07     0x27d6071f ASL  0x00000047) @ 0x1f6d5000
ACPI: MCFG (v016 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d4fc0
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20050624) @ 0x1f6d3aca
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1662.667 MHz processor.
Built 1 zonelists.  Total pages: 127718
Kernel command line: root=/dev/sda5 ata_piix.force_pcs=1 ro 
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
cpu 0 current c02a4440
Initializing CPU#0
CPU 0 irqstacks, hard=c02fd000 soft=c02fb000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 507632k/514892k available (1429k kernel code, 6700k reserved, 387k data, 172k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffb7000 - 0xfffff000   ( 288 kB)
    vmalloc : 0xe0000000 - 0xfffb5000   ( 511 MB)
    lowmem  : 0xc0000000 - 0xdf6d3000   ( 502 MB)
      .init : 0xc02cb000 - 0xc02f6000   ( 172 kB)
      .data : 0xc02654cf - 0xc02c644c   ( 387 kB)
      .text : 0xc0100000 - 0xc02654cf   (1429 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3327.38 BogoMIPS (lpj=1663692)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Booting processor 1/1 eip 2000
CPU 1 irqstacks, hard=c02fe000 soft=c02fc000
cpu 1 current df68d560
Initializing CPU#1
Calibrating delay using timer specific routine.. 3324.55 BogoMIPS (lpj=1662279)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Total of 2 processors activated (6651.94 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: 
CPU#0 had -856798 usecs TSC skew, fixed it up.
CPU#1 had 856798 usecs TSC skew, fixed it up.
Brought up 2 CPUs
migration_cost=69
NET: Registered protocol family 16
ACPI: bus type pci registered
ACPI Error (evregion-0317): No handler for Region [SMR2] (c1469f9c) [SystemIO] [20060707]
ACPI Error (exfldio-0290): Region SystemIO(1) has no handler [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\SXX6] (Node c146a824), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\SXX4] (Node c146a7fc), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\SX11] (Node c146a7c0), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\GORL] (Node c146a680), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.MB1_._CRS] (Node c146ae64), AE_NOT_EXIST
ACPI Error (uteval-0212): Method execution failed [\_SB_.MB1_._CRS] (Node c146ae64), AE_NOT_EXIST
PCI: BIOS Bug: MCFG area at e0000000 not reserved in ACPI
PCI: PCI BIOS revision 2.10 entry at 0xfaf96, last bus=12
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1080-10bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: dfd00000-dfdfffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:01.0
  IO window: 00002000-000020ff
  IO window: 00002400-000024ff
  PREFETCH window: 30000000-31ffffff
  MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: dfc00000-dfcfffff
  PREFETCH window: 30000000-31ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 18
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00ac7
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ata_piix 0000:00:1f.2: force ignoring PCS (0x15)
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xBFA8 irq 15
scsi0 : ata_piix
ata1: ENTER, pcs=0x15 base=0
ata1: LEAVE, pcs=0x15 present_mask=0x3
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 8
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2: ENTER, pcs=0x15 base=2
ata2: LEAVE, pcs=0x15 present_mask=0x0
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 0085 PQ: 0 ANSI: 5
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
intel_rng: FWH not detected
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bf80
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000bf60
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000bf40
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 22, io base 0x0000bf20
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:15:c5:1b:e1:de
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.18-rc6-mm2 ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1b.0 to 64
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
mice: PS/2 mouse device common for all mice
usb 5-2: new high speed USB device using ehci_hcd and address 2
usb 5-2: new device found, idVendor=413c, idProduct=a005
usb 5-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-2: configuration #1 chosen from 1 choice
hub 5-2:1.0: USB hub found
hub 5-2:1.0: 4 ports detected
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new device found, idVendor=0458, idProduct=002e
usb 2-2: new device strings: Mfr=2, Product=1, SerialNumber=0
usb 2-2: Product: NetScroll + Traveler
usb 2-2: Manufacturer: Genius
usb 2-2: configuration #1 chosen from 1 choice
input: Genius NetScroll + Traveler as /class/input/input3
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Adding 979924k swap on /dev/sda6.  Priority:-1 extents:1 across:979924k
EXT3 FS on sda5, internal journal
loop: loaded (max 8 devices)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
Time: acpi_pm clocksource has been installed.
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.5.0 20060119 on minor 0
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: AC Adapter [AC] (on-line)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Thermal Zone [THM] (54 C)
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.

[-- Attachment #3: lspci --]
[-- Type: application/octet-stream, Size: 13396 bytes --]

00:00.0 0600: 8086:27a0 (rev 03)
	Subsystem: 1028:01d4
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information

00:02.0 0300: 8086:27a2 (rev 03) (prog-if 00 [VGA])
	Subsystem: 1028:01d4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at eff8 [size=8]
	Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
	Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]
	Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:02.1 0380: 8086:27a6 (rev 03)
	Subsystem: 1028:01d4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
	Capabilities: [d0] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1b.0 0403: 8086:27d8 (rev 01)
	Subsystem: 1028:01d4
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [70] Express Unknown type IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <64ns, L1 <1us
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
		Link: Latency L0s <64ns, L1 <1us
		Link: ASPM Disabled CommClk- ExtSynch-
		Link: Speed unknown, Width x0

00:1c.0 0604: 8086:27d0 (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: fff00000-000fffff
	Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s unlimited, L1 unlimited
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
		Link: Latency L0s <1us, L1 <4us
		Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
		Link: Speed 2.5Gb/s, Width x0
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
		Slot: Number 2, PowerLimit 6.500000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: 0000:0000
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1c.1 0604: 8086:27d2 (rev 01) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
	I/O behind bridge: 0000f000-00000fff
	Memory behind bridge: dfd00000-dfdfffff
	Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [40] Express Root Port (Slot+) IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s unlimited, L1 unlimited
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
		Link: Latency L0s <256ns, L1 <4us
		Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
		Link: Speed 2.5Gb/s, Width x1
		Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
		Slot: Number 3, PowerLimit 6.500000
		Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet+ CmdCplt- HPIrq-
		Slot: AttnInd Unknown, PwrInd Unknown, Power-
		Root: Correctable- Non-Fatal- Fatal- PME-
	Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
		Address: 00000000  Data: 0000
	Capabilities: [90] Subsystem: 1028:01d4
	Capabilities: [a0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 0c03: 8086:27c8 (rev 01) (prog-if 00 [UHCI])
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 19
	Region 4: I/O ports at bf80 [size=32]

00:1d.1 0c03: 8086:27c9 (rev 01) (prog-if 00 [UHCI])
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 20
	Region 4: I/O ports at bf60 [size=32]

00:1d.2 0c03: 8086:27ca (rev 01) (prog-if 00 [UHCI])
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin C routed to IRQ 21
	Region 4: I/O ports at bf40 [size=32]

00:1d.3 0c03: 8086:27cb (rev 01) (prog-if 00 [UHCI])
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin D routed to IRQ 22
	Region 4: I/O ports at bf20 [size=32]

00:1d.7 0c03: 8086:27cc (rev 01) (prog-if 20 [EHCI])
	Subsystem: 1028:01d4
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port

00:1e.0 0604: 8086:2448 (rev e1) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: dfc00000-dfcfffff
	Prefetchable memory behind bridge: 0000000030000000-0000000031ffffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
	Capabilities: [50] Subsystem: 1028:01d4

00:1f.0 0601: 8086:27b9 (rev 01)
	Subsystem: 1028:01d4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Capabilities: [e0] Vendor Specific Information

00:1f.2 0101: 8086:27c4 (rev 01) (prog-if 80 [Master])
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at <ignored>
	Region 1: I/O ports at <ignored>
	Region 2: I/O ports at <ignored>
	Region 3: I/O ports at <ignored>
	Region 4: I/O ports at bfa0 [size=16]
	Capabilities: [70] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1f.3 0c05: 8086:27da (rev 01)
	Subsystem: 1028:01d4
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at 10c0 [size=32]

02:00.0 0200: 14e4:170c (rev 02)
	Subsystem: 1028:01d4
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at dfcfe000 (32-bit, non-prefetchable) [size=8K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-

02:01.0 0607: 1217:7135 (rev 21)
	Subsystem: 1028:01d4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at dfc00000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
	Memory window 0: 30000000-31fff000 (prefetchable)
	Memory window 1: 32000000-33fff000
	I/O window 0: 00002000-000020ff
	I/O window 1: 00002400-000024ff
	BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite-
	16-bit legacy interface ports at 0001

02:01.4 0c00: 1217:00f7 (rev 02) (prog-if 10 [OHCI])
	Subsystem: 1028:01d4
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at dfcfd000 (32-bit, non-prefetchable) [size=4K]
	Region 1: Memory at dfcfc800 (32-bit, non-prefetchable) [size=2K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0c:00.0 0280: 8086:4222 (rev 02)
	Subsystem: 8086:1020
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at dfdff000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [c8] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
		Address: 0000000000000000  Data: 0000
	Capabilities: [e0] Express Legacy Endpoint IRQ 0
		Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
		Device: Latency L0s <512ns, L1 unlimited
		Device: AtnBtn- AtnInd- PwrInd-
		Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
		Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
		Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
		Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
		Link: Latency L0s <128ns, L1 <64us
		Link: ASPM L1 Enabled RCB 64 bytes CommClk+ ExtSynch-
		Link: Speed 2.5Gb/s, Width x1


^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: PROBLEM: (libata) cdrom drive not detected in -mm series
  2006-09-12 11:30   ` Nelson A. de Oliveira
@ 2006-09-13 13:37     ` Tejun Heo
  2006-09-13 14:45       ` Alan Cox
  2006-09-14  0:41       ` Nelson A. de Oliveira
  0 siblings, 2 replies; 5+ messages in thread
From: Tejun Heo @ 2006-09-13 13:37 UTC (permalink / raw)
  To: Nelson A. de Oliveira
  Cc: linux-kernel, Andrew Morton, Jeff Garzik,
	linux-ide@vger.kernel.org, alan

[adding Alan to this thread]

The whole thread can be read from

http://thread.gmane.org/gmane.linux.kernel/445543/focus=445669

On Tue, Sep 12, 2006 at 08:30:50AM -0300, Nelson A. de Oliveira wrote:
> Hi!
> 
> On 9/12/06, Tejun Heo <htejun@gmail.com> wrote:
> >Nelson A. de Oliveira wrote:
> >> My USB CD-ROM drive (that is detected as a SCSI drive) is not being
> >> detected on the -mm series of the Kernel.
> >
> >s/USB/SATA/, I presume.
> 
> Yes, sorry!
> 
> >[--snip--]
> >-ata2.00: ATAPI, max UDMA/33
> >-ata2.00: configured for UDMA/33
> >-  Vendor: HL-DT-ST  Model: CDRW/DVD GCC4244  Rev: B101
> >-  Type:   CD-ROM                             ANSI SCSI revision: 05
> >
> >Argh... yet another PCS problem.  With whole -mm applied, does adding
> >kernel parameter 'ata_piix.force_pcs=1' make any difference?
> 
> No. Tried with latest 2.6.18-rc6-mm2 and still not detected.
> 
> >Please provide the following info.
> >
> >* the result of 'lspci -nvvv'
> >
> >* dmesg output with the attached patch applied (on top of -mm).
> 
> Applied the patch and sending the output of lspci and dmesg.

It seems that we screwed up while making two combined ports handled by
single host.  irq2 for the second port is added but other than that
the second port shared everything w/ the first port including port
flags, port ops and transfer masks.  In your case, this resulted in
the PATA ports handled as SATA ports resulting in misdetection.  I
missed this because combined on my mobo puts IDE port first, so SATA
ports doesn't get PCS check which works in most cases.

Can you verify whether the following patch fixes your problem?

Jeff, this doesn't affect upstream-fixes, so this isn't a showstopper
for 2.6.18.  The only left one is Keith's case but he's on road and
won't be able to test proposed fix till 18th.  I'll try to reproduce
it here.

Thanks.

diff --git a/drivers/ata/ata_piix.c b/drivers/ata/ata_piix.c
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 1c93154..bb66a12 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -5269,11 +5269,19 @@ void ata_port_init(struct ata_port *ap, 
 	ap->host = host;
 	ap->dev = ent->dev;
 	ap->port_no = port_no;
-	ap->pio_mask = ent->pio_mask;
-	ap->mwdma_mask = ent->mwdma_mask;
-	ap->udma_mask = ent->udma_mask;
-	ap->flags |= ent->port_flags;
-	ap->ops = ent->port_ops;
+	if (port_no == 1 && ent->pinfo2) {
+		ap->pio_mask = ent->pinfo2->pio_mask;
+		ap->mwdma_mask = ent->pinfo2->mwdma_mask;
+		ap->udma_mask = ent->pinfo2->udma_mask;
+		ap->flags |= ent->pinfo2->flags;
+		ap->ops = ent->pinfo2->port_ops;
+	} else {
+		ap->pio_mask = ent->pio_mask;
+		ap->mwdma_mask = ent->mwdma_mask;
+		ap->udma_mask = ent->udma_mask;
+		ap->flags |= ent->port_flags;
+		ap->ops = ent->port_ops;
+	}
 	ap->hw_sata_spd_limit = UINT_MAX;
 	ap->active_tag = ATA_TAG_POISON;
 	ap->last_ctl = 0xFF;
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 7605028..e72ed8d 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -858,6 +858,7 @@ ata_pci_init_native_mode(struct pci_dev 
 			probe_ent->port[p].bmdma_addr = bmdma;
 		}
 		ata_std_ports(&probe_ent->port[p]);
+		probe_ent->pinfo2 = port[1];
 		p++;
 	}
 
@@ -907,6 +908,7 @@ static struct ata_probe_ent *ata_pci_ini
 				probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
 		}
 		ata_std_ports(&probe_ent->port[1]);
+		probe_ent->pinfo2 = port[1];
 	} else
 		probe_ent->dummy_port_mask |= ATA_PORT_SECONDARY;
 
diff --git a/include/linux/libata.h b/include/linux/libata.h
index 8715305..ff67e75 100644
--- a/include/linux/libata.h
+++ b/include/linux/libata.h
@@ -361,6 +361,14 @@ struct ata_probe_ent {
 	unsigned long		_host_flags;
 	void __iomem		*mmio_base;
 	void			*private_data;
+
+	/* port_info for the secondary port.  Together with irq2, it's
+	 * used to implement non-uniform secondary port.  Currently,
+	 * the only user is ata_piix combined mode.  This workaround
+	 * will be removed together with ata_probe_ent when init model
+	 * is updated.
+	 */
+	const struct ata_port_info *pinfo2;
 };
 
 struct ata_host {

^ permalink raw reply related	[flat|nested] 5+ messages in thread

* Re: PROBLEM: (libata) cdrom drive not detected in -mm series
  2006-09-13 13:37     ` Tejun Heo
@ 2006-09-13 14:45       ` Alan Cox
  2006-09-14  0:41       ` Nelson A. de Oliveira
  1 sibling, 0 replies; 5+ messages in thread
From: Alan Cox @ 2006-09-13 14:45 UTC (permalink / raw)
  To: Tejun Heo
  Cc: Nelson A. de Oliveira, linux-kernel, Andrew Morton, Jeff Garzik,
	linux-ide@vger.kernel.org

Ar Mer, 2006-09-13 am 22:37 +0900, ysgrifennodd Tejun Heo:
> [adding Alan to this thread]
> 
> The whole thread can be read from

Looks sensible. I didn't consider that case because in the PATA world
nothing is quite that deranged. 



^ permalink raw reply	[flat|nested] 5+ messages in thread

* Re: PROBLEM: (libata) cdrom drive not detected in -mm series
  2006-09-13 13:37     ` Tejun Heo
  2006-09-13 14:45       ` Alan Cox
@ 2006-09-14  0:41       ` Nelson A. de Oliveira
  1 sibling, 0 replies; 5+ messages in thread
From: Nelson A. de Oliveira @ 2006-09-14  0:41 UTC (permalink / raw)
  To: Tejun Heo
  Cc: linux-kernel, Andrew Morton, Jeff Garzik,
	linux-ide@vger.kernel.org, alan

[-- Attachment #1: Type: text/plain, Size: 737 bytes --]

Hi!

On 9/13/06, Tejun Heo <htejun@gmail.com> wrote:
> It seems that we screwed up while making two combined ports handled by
> single host.  irq2 for the second port is added but other than that
> the second port shared everything w/ the first port including port
> flags, port ops and transfer masks.  In your case, this resulted in
> the PATA ports handled as SATA ports resulting in misdetection.  I
> missed this because combined on my mobo puts IDE port first, so SATA
> ports doesn't get PCS check which works in most cases.
>
> Can you verify whether the following patch fixes your problem?

Now it's working! :-D
Full dmesg is attached (I don't know if it's important, but I am
sending it anyway).

Thank you very much!

Nelson

[-- Attachment #2: dmesg --]
[-- Type: application/octet-stream, Size: 18914 bytes --]

Linux version 2.6.18-rc6-mm2 (root@orthrus) (gcc version 4.2.0 20060905 (experimental) (Debian 4.2-20060905-1)) #1 SMP PREEMPT Wed Sep 13 20:49:57 BRT 2006
BIOS-provided physical RAM map:
sanitize start
sanitize end
copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000001f5d3400 end: 000000001f6d3400 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001f6d3400 size: 000000000092cc00 end: 0000000020000000 type: 2
copy_e820_map() start: 00000000e0000000 size: 0000000010007000 end: 00000000f0007000 type: 2
copy_e820_map() start: 00000000f0008000 size: 0000000000004000 end: 00000000f000c000 type: 2
copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2
copy_e820_map() start: 00000000fed20000 size: 0000000000080000 end: 00000000feda0000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000010000 end: 00000000fee10000 type: 2
copy_e820_map() start: 00000000ffb00000 size: 0000000000500000 end: 0000000100000000 type: 2
 BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
 BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f6d3400 (usable)
 BIOS-e820: 000000001f6d3400 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved)
 BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
502MB LOWMEM available.
Entering add_active_range(0, 0, 128723) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   128723
early_node_map[1] active PFN ranges
    0:        0 ->   128723
On node 0 totalpages: 128723
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 973 pages used for memmap
  Normal zone: 123654 pages, LIFO batch:31
DMI 2.4 present.
ACPI: RSDP (v000 DELL                                  ) @ 0x000fc390
ACPI: RSDT (v001 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d3a96
ACPI: FADT (v001 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d4800
ACPI: MADT (v001 DELL    M07     0x27d6071f ASL  0x00000047) @ 0x1f6d5000
ACPI: MCFG (v016 DELL    M07     0x27d6071f ASL  0x00000061) @ 0x1f6d4fc0
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20050624) @ 0x1f6d3aca
ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 INTL 0x20050624) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1662.615 MHz processor.
Built 1 zonelists.  Total pages: 127718
Kernel command line: root=/dev/sda5 ro 
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
cpu 0 current c02a5440
Initializing CPU#0
CPU 0 irqstacks, hard=c02fe000 soft=c02fc000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 507628k/514892k available (1430k kernel code, 6704k reserved, 390k data, 172k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffb7000 - 0xfffff000   ( 288 kB)
    vmalloc : 0xe0000000 - 0xfffb5000   ( 511 MB)
    lowmem  : 0xc0000000 - 0xdf6d3000   ( 502 MB)
      .init : 0xc02cc000 - 0xc02f7000   ( 172 kB)
      .data : 0xc0265baf - 0xc02c744c   ( 390 kB)
      .text : 0xc0100000 - 0xc0265baf   (1430 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3327.38 BogoMIPS (lpj=1663693)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Booting processor 1/1 eip 2000
CPU 1 irqstacks, hard=c02ff000 soft=c02fd000
cpu 1 current df68d560
Initializing CPU#1
Calibrating delay using timer specific routine.. 3324.57 BogoMIPS (lpj=1662289)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
Total of 2 processors activated (6651.96 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: 
CPU#0 had -879173 usecs TSC skew, fixed it up.
CPU#1 had 879173 usecs TSC skew, fixed it up.
Brought up 2 CPUs
migration_cost=59
NET: Registered protocol family 16
ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: found ejectable bay
ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: Adding notify handler
ACPI: Bay [\_SB_.PCI0.IDE0.SEC0.MAST] Added
ACPI: bus type pci registered
ACPI Error (evregion-0317): No handler for Region [SMR2] (c1469f9c) [SystemIO] [20060707]
ACPI Error (exfldio-0290): Region SystemIO(1) has no handler [20060707]
ACPI Error (psparse-0537): Method parse/execution failed [\SXX6] (Node c146a824), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\SXX4] (Node c146a7fc), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\SX11] (Node c146a7c0), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\GORL] (Node c146a680), AE_NOT_EXIST
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.MB1_._CRS] (Node c146ae64), AE_NOT_EXIST
ACPI Error (uteval-0212): Method execution failed [\_SB_.MB1_._CRS] (Node c146ae64), AE_NOT_EXIST
PCI: BIOS Bug: MCFG area at e0000000 not reserved in ACPI
PCI: PCI BIOS revision 2.10 entry at 0xfaf96, last bus=12
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 1080-10bf claimed by ICH6 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try 'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: matching bay device
ACPI: \_SB_.PCI0.IDE0.SEC0.MAST: adding bay device
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: dfd00000-dfdfffff
  PREFETCH window: disabled.
PCI: Bus 3, cardbus bridge: 0000:02:01.0
  IO window: 00002000-000020ff
  IO window: 00002400-000024ff
  PREFETCH window: 30000000-31ffffff
  MEM window: 32000000-33ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 2000-2fff
  MEM window: dfc00000-dfcfffff
  PREFETCH window: 30000000-31ffffff
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 18
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
libata version 2.00 loaded.
ata_piix 0000:00:1f.2: version 2.00ac7
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xBFA8 irq 15
scsi0 : ata_piix
ata1.00: ATA-7, max UDMA/100, 156301488 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 8
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2.00: ATAPI, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2080B 0085 PQ: 0 ANSI: 5
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
scsi 1:0:0:0: CD-ROM            HL-DT-ST CDRW/DVD GCC4244 B101 PQ: 0 ANSI: 5
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Starting balanced_irq
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k freed
cdrom: no version for "struct_module" found: kernel tainted.
intel_rng: FWH not detected
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b44.c:v1.01 (Jun 16, 2006)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Broadcom 4400 10/100BaseT Ethernet 00:15:c5:1b:e1:de
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bf80
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000bf60
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000bf40
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 22, io base 0x0000bf20
usb usb3: new device found, idVendor=0000, idProduct=0000
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb usb4: new device found, idVendor=0000, idProduct=0000
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.18-rc6-mm2 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.3
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
input: PS/2 Mouse as /class/input/input1
input: AlpsPS/2 ALPS GlidePoint as /class/input/input2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: new device found, idVendor=0000, idProduct=0000
usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: EHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.18-rc6-mm2 ehci_hcd
usb usb5: SerialNumber: 0000:00:1d.7
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
mice: PS/2 mouse device common for all mice
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1b.0 to 64
usb 5-2: new high speed USB device using ehci_hcd and address 2
usb 5-2: new device found, idVendor=413c, idProduct=a005
usb 5-2: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 5-2: configuration #1 chosen from 1 choice
hub 5-2:1.0: USB hub found
hub 5-2:1.0: 4 ports detected
Adding 979924k swap on /dev/sda6.  Priority:-1 extents:1 across:979924k
EXT3 FS on sda5, internal journal
loop: loaded (max 8 devices)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
Time: acpi_pm clocksource has been installed.
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.5.0 20060119 on minor 0
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
ACPI: AC Adapter [AC] (on-line)
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PBTN]
ACPI: Sleep Button (CM) [SBTN]
ACPI: Thermal Zone [THM] (36 C)
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: new device found, idVendor=0458, idProduct=002e
usb 2-2: new device strings: Mfr=2, Product=1, SerialNumber=0
usb 2-2: Product: NetScroll + Traveler
usb 2-2: Manufacturer: Genius
usb 2-2: configuration #1 chosen from 1 choice
input: Genius NetScroll + Traveler as /class/input/input3
input: USB HID v1.10 Mouse [Genius NetScroll + Traveler] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2006-09-14  0:42 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
     [not found] <9bfa9ae0609111802o9131e8bg6c5d394ad87b16ea@mail.gmail.com>
2006-09-12  7:41 ` PROBLEM: (libata) cdrom drive not detected in -mm series Tejun Heo
2006-09-12 11:30   ` Nelson A. de Oliveira
2006-09-13 13:37     ` Tejun Heo
2006-09-13 14:45       ` Alan Cox
2006-09-14  0:41       ` Nelson A. de Oliveira

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox