* Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work
@ 2009-10-23 12:31 Milan Burgdorf
2009-10-23 13:19 ` Mikael Pettersson
0 siblings, 1 reply; 4+ messages in thread
From: Milan Burgdorf @ 2009-10-23 12:31 UTC (permalink / raw)
To: linux-ide
Dear Mr. Pettersson and the whole LINUX-IDE-team,
I'm working with Xubuntu 8.04 by using Kernel 2.6.24-24-generic. My two
2,5-Zoll SATA-II-Harddisks are connected with a Promise SATA 300 TX2
Plus-Controller.
When the disks work with high I/O, than I become the similar problems
like they are described in
"http://marc.info/?l=linux-ide&m=121475606225101&w=2" and
"http://marc.info/?l=linux-ide&m=120134441006713&w=2":
Oct 15 20:20:46 alexandria-epia kernel: [ 5731.478618] res
40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Oct 15 20:20:51 alexandria-epia kernel: [ 5736.825857] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526446] ata1: device not
ready (errno=-16), forcing hardreset
Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526472] ata1: hard
resetting link
Oct 15 20:21:02 alexandria-epia kernel: [ 5747.713897] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:06 alexandria-epia kernel: [ 5751.575082] ata1: hard
resetting link
Oct 15 20:21:12 alexandria-epia kernel: [ 5757.762534] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:16 alexandria-epia kernel: [ 5761.623715] ata1: hard
resetting link
Oct 15 20:21:22 alexandria-epia kernel: [ 5767.811162] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650099] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650114] ata1: hard
resetting link
Oct 15 20:21:56 alexandria-epia kernel: [ 5801.658417] ata1.00: disabled
To solve my problem I patched the sata_promise-Module with your three
patches from "http://user.it.uu.se/~mikpe/linux/patches/2.6/OLD/2.6.24/"
and installed the new module.
After this I checked hopefully my /var/log/messages, but the disk run
anymore in 3.0GB/s-Mode, and again I become the I/O-problems:
Aug 24 16:21:40 alexandria-epia kernel: [ 25.804737] scsi0 : sata_promise
Aug 24 16:21:40 alexandria-epia kernel: [ 25.812721] scsi1 : sata_promise
Aug 24 16:21:40 alexandria-epia kernel: [ 25.832765] scsi2 : sata_promise
Aug 24 16:21:40 alexandria-epia kernel: [ 25.832958] ata1: SATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021200 irq 10
Aug 24 16:21:40 alexandria-epia kernel: [ 25.833023] ata2: SATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021280 irq 10
Aug 24 16:21:40 alexandria-epia kernel: [ 25.833085] ata3: PATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021300 irq 10
Aug 24 16:21:40 alexandria-epia kernel: [ 26.300682] ata1: SATA link
up 3.0 Gbps (SStatus 123 SControl 300)
Aug 24 16:21:40 alexandria-epia kernel: [ 26.664283] ata1.00: ATA-8:
WDC WD2500BEVT-22ZCT0, 11.01A11, max UDMA/133
Aug 24 16:21:40 alexandria-epia kernel: [ 26.664355] ata1.00:
488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
Aug 24 16:21:40 alexandria-epia kernel: [ 26.674118] ata1.00:
configured for UDMA/133
Aug 24 16:21:40 alexandria-epia kernel: [ 26.988560] usb 1-1: new low
speed USB device using uhci_hcd and address 3
Aug 24 16:21:40 alexandria-epia kernel: [ 27.140550] ata2: SATA link
up 3.0 Gbps (SStatus 123 SControl 300)
Aug 24 16:21:40 alexandria-epia kernel: [ 27.148799] ata2.00: ATA-8:
ST9250827AS, 3.AAA, max UDMA/133
Aug 24 16:21:40 alexandria-epia kernel: [ 27.148865] ata2.00:
488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
Aug 24 16:21:40 alexandria-epia kernel: [ 27.163553] usb 1-1:
configuration #1 chosen from 1 choice
Aug 24 16:21:40 alexandria-epia kernel: [ 27.164844] ata2.00:
configured for UDMA/133
Aug 24 16:21:40 alexandria-epia kernel: [ 27.320749] scsi 0:0:0:0:
Direct-Access ATA WDC WD2500BEVT-2 11.0 PQ: 0 ANSI: 5
Aug 24 16:21:40 alexandria-epia kernel: [ 27.321316] scsi 1:0:0:0:
Direct-Access ATA ST9250827AS 3.AA PQ: 0 ANSI: 5
Is there another possibility to force the Promise-Controller down to 1.5
GB/s?
Best regards,
Milan W. Burgdorf
---------------------------------------------------------------------------------------------
My controller:
00:14.0 Mass storage controller: Promise Technology, Inc. PDC40775 (SATA
300 TX2plus) (rev 02)
Subsystem: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus)
Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 10
I/O ports at e800 [size=128]
I/O ports at ec00 [size=256]
Memory at e8021000 (32-bit, non-prefetchable) [size=4K]
Memory at e8000000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 20000000 [disabled] [size=32K]
Capabilities: [60] Power Management version 2
My patched sata_promise.c:
/*
* sata_promise.c - Promise SATA
*
* Maintained by: Jeff Garzik <jgarzik@pobox.com>
* Mikael Pettersson <mikpe@it.uu.se>
* Please ALWAYS copy linux-ide@vger.kernel.org
* on emails.
*
* Copyright 2003-2004 Red Hat, Inc.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2, or (at your option)
* any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; see the file COPYING. If not, write to
* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA.
*
*
* libata documentation is available via 'make {ps|pdf}docs',
* as Documentation/DocBook/libata.*
*
* Hardware information only available under NDA.
*
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/device.h>
#include <scsi/scsi.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
#include "sata_promise.h"
#define DRV_NAME "sata_promise"
#define DRV_VERSION "2.11"
enum {
PDC_MAX_PORTS = 4,
PDC_MMIO_BAR = 3,
PDC_MAX_PRD = LIBATA_MAX_PRD - 1, /* -1 for ASIC PRD bug workaround */
/* register offsets */
PDC_FEATURE = 0x04, /* Feature/Error reg (per port) */
PDC_SECTOR_COUNT = 0x08, /* Sector count reg (per port) */
PDC_SECTOR_NUMBER = 0x0C, /* Sector number reg (per port) */
PDC_CYLINDER_LOW = 0x10, /* Cylinder low reg (per port) */
PDC_CYLINDER_HIGH = 0x14, /* Cylinder high reg (per port) */
PDC_DEVICE = 0x18, /* Device/Head reg (per port) */
PDC_COMMAND = 0x1C, /* Command/status reg (per port) */
PDC_ALTSTATUS = 0x38, /* Alternate-status/device-control reg (per port) */
PDC_PKT_SUBMIT = 0x40, /* Command packet pointer addr */
PDC_INT_SEQMASK = 0x40, /* Mask of asserted SEQ INTs */
PDC_FLASH_CTL = 0x44, /* Flash control register */
PDC_GLOBAL_CTL = 0x48, /* Global control/status (per port) */
PDC_CTLSTAT = 0x60, /* IDE control and status (per port) */
PDC_SATA_PLUG_CSR = 0x6C, /* SATA Plug control/status reg */
PDC2_SATA_PLUG_CSR = 0x60, /* SATAII Plug control/status reg */
PDC_TBG_MODE = 0x41C, /* TBG mode (not SATAII) */
PDC_SLEW_CTL = 0x470, /* slew rate control reg (not SATAII) */
/* PDC_GLOBAL_CTL bit definitions */
PDC_PH_ERR = (1 << 8), /* PCI error while loading packet */
PDC_SH_ERR = (1 << 9), /* PCI error while loading S/G table */
PDC_DH_ERR = (1 << 10), /* PCI error while loading data */
PDC2_HTO_ERR = (1 << 12), /* host bus timeout */
PDC2_ATA_HBA_ERR = (1 << 13), /* error during SATA DATA FIS transmission */
PDC2_ATA_DMA_CNT_ERR = (1 << 14), /* DMA DATA FIS size differs from S/G
count */
PDC_OVERRUN_ERR = (1 << 19), /* S/G byte count larger than HD requires */
PDC_UNDERRUN_ERR = (1 << 20), /* S/G byte count less than HD requires */
PDC_DRIVE_ERR = (1 << 21), /* drive error */
PDC_PCI_SYS_ERR = (1 << 22), /* PCI system error */
PDC1_PCI_PARITY_ERR = (1 << 23), /* PCI parity error (from SATA150
driver) */
PDC1_ERR_MASK = PDC1_PCI_PARITY_ERR,
PDC2_ERR_MASK = PDC2_HTO_ERR | PDC2_ATA_HBA_ERR |
PDC2_ATA_DMA_CNT_ERR,
PDC_ERR_MASK = PDC_PH_ERR | PDC_SH_ERR | PDC_DH_ERR |
PDC_OVERRUN_ERR | PDC_UNDERRUN_ERR |
PDC_DRIVE_ERR | PDC_PCI_SYS_ERR |
PDC1_ERR_MASK | PDC2_ERR_MASK,
board_2037x = 0, /* FastTrak S150 TX2plus */
board_2037x_pata = 1, /* FastTrak S150 TX2plus PATA port */
board_20319 = 2, /* FastTrak S150 TX4 */
board_20619 = 3, /* FastTrak TX4000 */
board_2057x = 4, /* SATAII150 Tx2plus */
board_2057x_pata = 5, /* SATAII150 Tx2plus PATA port */
board_40518 = 6, /* SATAII150 Tx4 */
PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */
/* Sequence counter control registers bit definitions */
PDC_SEQCNTRL_INT_MASK = (1 << 5), /* Sequence Interrupt Mask */
/* Feature register values */
PDC_FEATURE_ATAPI_PIO = 0x00, /* ATAPI data xfer by PIO */
PDC_FEATURE_ATAPI_DMA = 0x01, /* ATAPI data xfer by DMA */
/* Device/Head register values */
PDC_DEVICE_SATA = 0xE0, /* Device/Head value for SATA devices */
/* PDC_CTLSTAT bit definitions */
PDC_DMA_ENABLE = (1 << 7),
PDC_IRQ_DISABLE = (1 << 10),
PDC_RESET = (1 << 11), /* HDMA reset */
PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY |
ATA_FLAG_MMIO |
ATA_FLAG_PIO_POLLING,
/* ap->flags bits */
PDC_FLAG_GEN_II = (1 << 24),
PDC_FLAG_SATA_PATA = (1 << 25), /* supports SATA + PATA */
PDC_FLAG_4_PORTS = (1 << 26), /* 4 ports */
};
struct pdc_port_priv {
u8 *pkt;
dma_addr_t pkt_dma;
};
static int pdc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg,
u32 *val);
static int pdc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg,
u32 val);
static int pdc_ata_init_one (struct pci_dev *pdev, const struct
pci_device_id *ent);
static int pdc_common_port_start(struct ata_port *ap);
static int pdc_sata_port_start(struct ata_port *ap);
static void pdc_qc_prep(struct ata_queued_cmd *qc);
static void pdc_tf_load_mmio(struct ata_port *ap, const struct
ata_taskfile *tf);
static void pdc_exec_command_mmio(struct ata_port *ap, const struct
ata_taskfile *tf);
static int pdc_check_atapi_dma(struct ata_queued_cmd *qc);
static int pdc_old_sata_check_atapi_dma(struct ata_queued_cmd *qc);
static void pdc_irq_clear(struct ata_port *ap);
static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc);
static void pdc_freeze(struct ata_port *ap);
static void pdc_sata_freeze(struct ata_port *ap);
static void pdc_thaw(struct ata_port *ap);
static void pdc_sata_thaw(struct ata_port *ap);
static void pdc_pata_error_handler(struct ata_port *ap);
static void pdc_sata_error_handler(struct ata_port *ap);
static void pdc_post_internal_cmd(struct ata_queued_cmd *qc);
static int pdc_pata_cable_detect(struct ata_port *ap);
static int pdc_sata_cable_detect(struct ata_port *ap);
static struct scsi_host_template pdc_ata_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = PDC_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static const struct ata_port_operations pdc_sata_ops = {
.tf_load = pdc_tf_load_mmio,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = pdc_exec_command_mmio,
.dev_select = ata_std_dev_select,
.check_atapi_dma = pdc_check_atapi_dma,
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue_prot,
.freeze = pdc_sata_freeze,
.thaw = pdc_sata_thaw,
.error_handler = pdc_sata_error_handler,
.post_internal_cmd = pdc_post_internal_cmd,
.cable_detect = pdc_sata_cable_detect,
.data_xfer = ata_data_xfer,
.irq_clear = pdc_irq_clear,
.irq_on = ata_irq_on,
.scr_read = pdc_sata_scr_read,
.scr_write = pdc_sata_scr_write,
.port_start = pdc_sata_port_start,
};
/* First-generation chips need a more restrictive ->check_atapi_dma op */
static const struct ata_port_operations pdc_old_sata_ops = {
.tf_load = pdc_tf_load_mmio,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = pdc_exec_command_mmio,
.dev_select = ata_std_dev_select,
.check_atapi_dma = pdc_old_sata_check_atapi_dma,
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue_prot,
.freeze = pdc_sata_freeze,
.thaw = pdc_sata_thaw,
.error_handler = pdc_sata_error_handler,
.post_internal_cmd = pdc_post_internal_cmd,
.cable_detect = pdc_sata_cable_detect,
.data_xfer = ata_data_xfer,
.irq_clear = pdc_irq_clear,
.irq_on = ata_irq_on,
.scr_read = pdc_sata_scr_read,
.scr_write = pdc_sata_scr_write,
.port_start = pdc_sata_port_start,
};
static const struct ata_port_operations pdc_pata_ops = {
.tf_load = pdc_tf_load_mmio,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = pdc_exec_command_mmio,
.dev_select = ata_std_dev_select,
.check_atapi_dma = pdc_check_atapi_dma,
.qc_prep = pdc_qc_prep,
.qc_issue = pdc_qc_issue_prot,
.freeze = pdc_freeze,
.thaw = pdc_thaw,
.error_handler = pdc_pata_error_handler,
.post_internal_cmd = pdc_post_internal_cmd,
.cable_detect = pdc_pata_cable_detect,
.data_xfer = ata_data_xfer,
.irq_clear = pdc_irq_clear,
.irq_on = ata_irq_on,
.port_start = pdc_common_port_start,
};
static const struct ata_port_info pdc_port_info[] = {
[board_2037x] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_SATA_PATA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
[board_2037x_pata] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
[board_20319] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_old_sata_ops,
},
[board_20619] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS |
PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
[board_2057x] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_GEN_II | PDC_FLAG_SATA_PATA,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
[board_2057x_pata] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS |
PDC_FLAG_GEN_II,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_pata_ops,
},
[board_40518] =
{
.flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA |
PDC_FLAG_GEN_II | PDC_FLAG_4_PORTS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x07, /* mwdma0-2 */
.udma_mask = ATA_UDMA6,
.port_ops = &pdc_sata_ops,
},
};
static const struct pci_device_id pdc_ata_pci_tbl[] = {
{ PCI_VDEVICE(PROMISE, 0x3371), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3373), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3375), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3376), board_2037x },
{ PCI_VDEVICE(PROMISE, 0x3570), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3571), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3574), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3577), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d73), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3d75), board_2057x },
{ PCI_VDEVICE(PROMISE, 0x3318), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3319), board_20319 },
{ PCI_VDEVICE(PROMISE, 0x3515), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x3519), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x3d17), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x3d18), board_40518 },
{ PCI_VDEVICE(PROMISE, 0x6629), board_20619 },
{ } /* terminate list */
};
static struct pci_driver pdc_ata_pci_driver = {
.name = DRV_NAME,
.id_table = pdc_ata_pci_tbl,
.probe = pdc_ata_init_one,
.remove = ata_pci_remove_one,
};
static int pdc_common_port_start(struct ata_port *ap)
{
struct device *dev = ap->host->dev;
struct pdc_port_priv *pp;
int rc;
rc = ata_port_start(ap);
if (rc)
return rc;
pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL);
if (!pp)
return -ENOMEM;
pp->pkt = dmam_alloc_coherent(dev, 128, &pp->pkt_dma, GFP_KERNEL);
if (!pp->pkt)
return -ENOMEM;
ap->private_data = pp;
return 0;
}
static int pdc_sata_port_start(struct ata_port *ap)
{
int rc;
rc = pdc_common_port_start(ap);
if (rc)
return rc;
/* fix up PHYMODE4 align timing */
if (ap->flags & PDC_FLAG_GEN_II) {
void __iomem *mmio = ap->ioaddr.scr_addr;
unsigned int tmp;
tmp = readl(mmio + 0x014);
tmp = (tmp & ~3) | 1; /* set bits 1:0 = 0:1 */
writel(tmp, mmio + 0x014);
}
/* hack SControl to limit speed to 1.5Gbps */
if (ap->flags & PDC_FLAG_GEN_II) {
void __iomem *mmio = (void __iomem *) ap->ioaddr.scr_addr;
unsigned int tmp1, tmp2;
tmp1 = readl(mmio + 0x008);
tmp2 = (tmp1 & 0xffffff00) | 0x00000011;
writel(tmp2, mmio + 0x008);
readl(mmio + 0x008); /* flush */
printk("%s(port %u): adjusted SControl from 0x%08x to 0x%08x\n",
__FUNCTION__, ap->port_no, tmp1, tmp2);
}
return 0;
}
static void pdc_reset_port(struct ata_port *ap)
{
void __iomem *mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT;
unsigned int i;
u32 tmp;
for (i = 11; i > 0; i--) {
tmp = readl(mmio);
if (tmp & PDC_RESET)
break;
udelay(100);
tmp |= PDC_RESET;
writel(tmp, mmio);
}
tmp &= ~PDC_RESET;
writel(tmp, mmio);
readl(mmio); /* flush */
}
static int pdc_pata_cable_detect(struct ata_port *ap)
{
u8 tmp;
void __iomem *mmio = ap->ioaddr.cmd_addr + PDC_CTLSTAT + 0x03;
tmp = readb(mmio);
if (tmp & 0x01)
return ATA_CBL_PATA40;
return ATA_CBL_PATA80;
}
static int pdc_sata_cable_detect(struct ata_port *ap)
{
return ATA_CBL_SATA;
}
static int pdc_sata_scr_read(struct ata_port *ap, unsigned int sc_reg,
u32 *val)
{
if (sc_reg > SCR_CONTROL)
return -EINVAL;
*val = readl(ap->ioaddr.scr_addr + (sc_reg * 4));
return 0;
}
static int pdc_sata_scr_write(struct ata_port *ap, unsigned int sc_reg,
u32 val)
{
if (sc_reg > SCR_CONTROL)
return -EINVAL;
writel(val, ap->ioaddr.scr_addr + (sc_reg * 4));
return 0;
}
static void pdc_atapi_pkt(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
dma_addr_t sg_table = ap->prd_dma;
unsigned int cdb_len = qc->dev->cdb_len;
u8 *cdb = qc->cdb;
struct pdc_port_priv *pp = ap->private_data;
u8 *buf = pp->pkt;
u32 *buf32 = (u32 *) buf;
unsigned int dev_sel, feature, nbytes;
/* set control bits (byte 0), zero delay seq id (byte 3),
* and seq id (byte 2)
*/
switch (qc->tf.protocol) {
case ATA_PROT_ATAPI_DMA:
if (!(qc->tf.flags & ATA_TFLAG_WRITE))
buf32[0] = cpu_to_le32(PDC_PKT_READ);
else
buf32[0] = 0;
break;
case ATA_PROT_ATAPI_NODATA:
buf32[0] = cpu_to_le32(PDC_PKT_NODATA);
break;
default:
BUG();
break;
}
buf32[1] = cpu_to_le32(sg_table); /* S/G table addr */
buf32[2] = 0; /* no next-packet */
/* select drive */
if (sata_scr_valid(&ap->link)) {
dev_sel = PDC_DEVICE_SATA;
} else {
dev_sel = ATA_DEVICE_OBS;
if (qc->dev->devno != 0)
dev_sel |= ATA_DEV1;
}
buf[12] = (1 << 5) | ATA_REG_DEVICE;
buf[13] = dev_sel;
buf[14] = (1 << 5) | ATA_REG_DEVICE | PDC_PKT_CLEAR_BSY;
buf[15] = dev_sel; /* once more, waiting for BSY to clear */
buf[16] = (1 << 5) | ATA_REG_NSECT;
buf[17] = 0x00;
buf[18] = (1 << 5) | ATA_REG_LBAL;
buf[19] = 0x00;
/* set feature and byte counter registers */
if (qc->tf.protocol != ATA_PROT_ATAPI_DMA) {
feature = PDC_FEATURE_ATAPI_PIO;
/* set byte counter register to real transfer byte count */
nbytes = qc->nbytes;
if (nbytes > 0xffff)
nbytes = 0xffff;
} else {
feature = PDC_FEATURE_ATAPI_DMA;
/* set byte counter register to 0 */
nbytes = 0;
}
buf[20] = (1 << 5) | ATA_REG_FEATURE;
buf[21] = feature;
buf[22] = (1 << 5) | ATA_REG_BYTEL;
buf[23] = nbytes & 0xFF;
buf[24] = (1 << 5) | ATA_REG_BYTEH;
buf[25] = (nbytes >> 8) & 0xFF;
/* send ATAPI packet command 0xA0 */
buf[26] = (1 << 5) | ATA_REG_CMD;
buf[27] = ATA_CMD_PACKET;
/* select drive and check DRQ */
buf[28] = (1 << 5) | ATA_REG_DEVICE | PDC_PKT_WAIT_DRDY;
buf[29] = dev_sel;
/* we can represent cdb lengths 2/4/6/8/10/12/14/16 */
BUG_ON(cdb_len & ~0x1E);
/* append the CDB as the final part */
buf[30] = (((cdb_len >> 1) & 7) << 5) | ATA_REG_DATA | PDC_LAST_REG;
memcpy(buf+31, cdb, cdb_len);
}
/**
* pdc_fill_sg - Fill PCI IDE PRD table
* @qc: Metadata associated with taskfile to be transferred
*
* Fill PCI IDE PRD (scatter-gather) table with segments
* associated with the current disk command.
* Make sure hardware does not choke on it.
*
* LOCKING:
* spin_lock_irqsave(host lock)
*
*/
static void pdc_fill_sg(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct scatterlist *sg;
unsigned int idx;
const u32 SG_COUNT_ASIC_BUG = 41*4;
if (!(qc->flags & ATA_QCFLAG_DMAMAP))
return;
WARN_ON(qc->__sg == NULL);
WARN_ON(qc->n_elem == 0 && qc->pad_len == 0);
idx = 0;
ata_for_each_sg(sg, qc) {
u32 addr, offset;
u32 sg_len, len;
/* determine if physical DMA addr spans 64K boundary.
* Note h/w doesn't support 64-bit, so we unconditionally
* truncate dma_addr_t to u32.
*/
addr = (u32) sg_dma_address(sg);
sg_len = sg_dma_len(sg);
while (sg_len) {
offset = addr & 0xffff;
len = sg_len;
if ((offset + sg_len) > 0x10000)
len = 0x10000 - offset;
ap->prd[idx].addr = cpu_to_le32(addr);
ap->prd[idx].flags_len = cpu_to_le32(len & 0xffff);
VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
idx++;
sg_len -= len;
addr += len;
}
}
if (idx) {
u32 len = le32_to_cpu(ap->prd[idx - 1].flags_len);
if (len > SG_COUNT_ASIC_BUG) {
u32 addr;
VPRINTK("Splitting last PRD.\n");
addr = le32_to_cpu(ap->prd[idx - 1].addr);
ap->prd[idx - 1].flags_len = cpu_to_le32(len - SG_COUNT_ASIC_BUG);
VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx - 1, addr, SG_COUNT_ASIC_BUG);
addr = addr + len - SG_COUNT_ASIC_BUG;
len = SG_COUNT_ASIC_BUG;
ap->prd[idx].addr = cpu_to_le32(addr);
ap->prd[idx].flags_len = cpu_to_le32(len);
VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", idx, addr, len);
idx++;
}
ap->prd[idx - 1].flags_len |= cpu_to_le32(ATA_PRD_EOT);
}
}
static void pdc_qc_prep(struct ata_queued_cmd *qc)
{
struct pdc_port_priv *pp = qc->ap->private_data;
unsigned int i;
VPRINTK("ENTER\n");
switch (qc->tf.protocol) {
case ATA_PROT_DMA:
pdc_fill_sg(qc);
/* fall through */
case ATA_PROT_NODATA:
i = pdc_pkt_header(&qc->tf, qc->ap->prd_dma,
qc->dev->devno, pp->pkt);
if (qc->tf.flags & ATA_TFLAG_LBA48)
i = pdc_prep_lba48(&qc->tf, pp->pkt, i);
else
i = pdc_prep_lba28(&qc->tf, pp->pkt, i);
pdc_pkt_footer(&qc->tf, pp->pkt, i);
break;
case ATA_PROT_ATAPI:
pdc_fill_sg(qc);
break;
case ATA_PROT_ATAPI_DMA:
pdc_fill_sg(qc);
/*FALLTHROUGH*/
case ATA_PROT_ATAPI_NODATA:
pdc_atapi_pkt(qc);
break;
default:
break;
}
}
static int pdc_is_sataii_tx4(unsigned long flags)
{
const unsigned long mask = PDC_FLAG_GEN_II | PDC_FLAG_4_PORTS;
return (flags & mask) == mask;
}
static unsigned int pdc_port_no_to_ata_no(unsigned int port_no,
int is_sataii_tx4)
{
static const unsigned char sataii_tx4_port_remap[4] = { 3, 1, 0, 2};
return is_sataii_tx4 ? sataii_tx4_port_remap[port_no] : port_no;
}
static unsigned int pdc_sata_nr_ports(const struct ata_port *ap)
{
return (ap->flags & PDC_FLAG_4_PORTS) ? 4 : 2;
}
static unsigned int pdc_sata_ata_port_to_ata_no(const struct ata_port *ap)
{
const struct ata_host *host = ap->host;
unsigned int nr_ports = pdc_sata_nr_ports(ap);
unsigned int i;
for(i = 0; i < nr_ports && host->ports[i] != ap; ++i)
;
BUG_ON(i >= nr_ports);
return pdc_port_no_to_ata_no(i, pdc_is_sataii_tx4(ap->flags));
}
static unsigned int pdc_sata_hotplug_offset(const struct ata_port *ap)
{
return (ap->flags & PDC_FLAG_GEN_II) ? PDC2_SATA_PLUG_CSR :
PDC_SATA_PLUG_CSR;
}
static void pdc_freeze(struct ata_port *ap)
{
void __iomem *mmio = ap->ioaddr.cmd_addr;
u32 tmp;
tmp = readl(mmio + PDC_CTLSTAT);
tmp |= PDC_IRQ_DISABLE;
tmp &= ~PDC_DMA_ENABLE;
writel(tmp, mmio + PDC_CTLSTAT);
readl(mmio + PDC_CTLSTAT); /* flush */
}
static void pdc_sata_freeze(struct ata_port *ap)
{
struct ata_host *host = ap->host;
void __iomem *host_mmio = host->iomap[PDC_MMIO_BAR];
unsigned int hotplug_offset = pdc_sata_hotplug_offset(ap);
unsigned int ata_no = pdc_sata_ata_port_to_ata_no(ap);
u32 hotplug_status;
/* Disable hotplug events on this port.
*
* Locking:
* 1) hotplug register accesses must be serialised via host->lock
* 2) ap->lock == &ap->host->lock
* 3) ->freeze() and ->thaw() are called with ap->lock held
*/
hotplug_status = readl(host_mmio + hotplug_offset);
hotplug_status |= 0x11 << (ata_no + 16);
writel(hotplug_status, host_mmio + hotplug_offset);
readl(host_mmio + hotplug_offset); /* flush */
pdc_freeze(ap);
}
static void pdc_thaw(struct ata_port *ap)
{
void __iomem *mmio = ap->ioaddr.cmd_addr;
u32 tmp;
/* clear IRQ */
readl(mmio + PDC_COMMAND);
/* turn IRQ back on */
tmp = readl(mmio + PDC_CTLSTAT);
tmp &= ~PDC_IRQ_DISABLE;
writel(tmp, mmio + PDC_CTLSTAT);
readl(mmio + PDC_CTLSTAT); /* flush */
}
static void pdc_sata_thaw(struct ata_port *ap)
{
struct ata_host *host = ap->host;
void __iomem *host_mmio = host->iomap[PDC_MMIO_BAR];
unsigned int hotplug_offset = pdc_sata_hotplug_offset(ap);
unsigned int ata_no = pdc_sata_ata_port_to_ata_no(ap);
u32 hotplug_status;
pdc_thaw(ap);
/* Enable hotplug events on this port.
* Locking: see pdc_sata_freeze().
*/
hotplug_status = readl(host_mmio + hotplug_offset);
hotplug_status |= 0x11 << ata_no;
hotplug_status &= ~(0x11 << (ata_no + 16));
writel(hotplug_status, host_mmio + hotplug_offset);
readl(host_mmio + hotplug_offset); /* flush */
}
static void pdc_common_error_handler(struct ata_port *ap, ata_reset_fn_t
hardreset)
{
if (!(ap->pflags & ATA_PFLAG_FROZEN))
pdc_reset_port(ap);
/* perform recovery */
ata_do_eh(ap, ata_std_prereset, ata_std_softreset, hardreset,
ata_std_postreset);
}
static void pdc_pata_error_handler(struct ata_port *ap)
{
pdc_common_error_handler(ap, NULL);
}
static void pdc_sata_error_handler(struct ata_port *ap)
{
pdc_common_error_handler(ap, sata_std_hardreset);
}
static void pdc_post_internal_cmd(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
/* make DMA engine forget about the failed command */
if (qc->flags & ATA_QCFLAG_FAILED)
pdc_reset_port(ap);
}
static void pdc_error_intr(struct ata_port *ap, struct ata_queued_cmd *qc,
u32 port_status, u32 err_mask)
{
struct ata_eh_info *ehi = &ap->link.eh_info;
unsigned int ac_err_mask = 0;
ata_ehi_clear_desc(ehi);
ata_ehi_push_desc(ehi, "port_status 0x%08x", port_status);
port_status &= err_mask;
if (port_status & PDC_DRIVE_ERR)
ac_err_mask |= AC_ERR_DEV;
if (port_status & (PDC_OVERRUN_ERR | PDC_UNDERRUN_ERR))
ac_err_mask |= AC_ERR_HSM;
if (port_status & (PDC2_ATA_HBA_ERR | PDC2_ATA_DMA_CNT_ERR))
ac_err_mask |= AC_ERR_ATA_BUS;
if (port_status & (PDC_PH_ERR | PDC_SH_ERR | PDC_DH_ERR | PDC2_HTO_ERR
| PDC_PCI_SYS_ERR | PDC1_PCI_PARITY_ERR))
ac_err_mask |= AC_ERR_HOST_BUS;
if (sata_scr_valid(&ap->link)) {
u32 serror;
pdc_sata_scr_read(ap, SCR_ERROR, &serror);
ehi->serror |= serror;
}
qc->err_mask |= ac_err_mask;
pdc_reset_port(ap);
ata_port_abort(ap);
}
static inline unsigned int pdc_host_intr(struct ata_port *ap,
struct ata_queued_cmd *qc)
{
unsigned int handled = 0;
void __iomem *port_mmio = ap->ioaddr.cmd_addr;
u32 port_status, err_mask;
err_mask = PDC_ERR_MASK;
if (ap->flags & PDC_FLAG_GEN_II)
err_mask &= ~PDC1_ERR_MASK;
else
err_mask &= ~PDC2_ERR_MASK;
port_status = readl(port_mmio + PDC_GLOBAL_CTL);
if (unlikely(port_status & err_mask)) {
pdc_error_intr(ap, qc, port_status, err_mask);
return 1;
}
switch (qc->tf.protocol) {
case ATA_PROT_DMA:
case ATA_PROT_NODATA:
case ATA_PROT_ATAPI_DMA:
case ATA_PROT_ATAPI_NODATA:
qc->err_mask |= ac_err_mask(ata_wait_idle(ap));
ata_qc_complete(qc);
handled = 1;
break;
default:
ap->stats.idle_irq++;
break;
}
return handled;
}
static void pdc_irq_clear(struct ata_port *ap)
{
void __iomem *mmio = ap->ioaddr.cmd_addr;
readl(mmio + PDC_COMMAND);
}
static irqreturn_t pdc_interrupt(int irq, void *dev_instance)
{
struct ata_host *host = dev_instance;
struct ata_port *ap;
u32 mask = 0;
unsigned int i, tmp;
unsigned int handled = 0;
void __iomem *mmio_base;
unsigned int hotplug_offset, ata_no;
u32 hotplug_status;
int is_sataii_tx4;
VPRINTK("ENTER\n");
if (!host || !host->iomap[PDC_MMIO_BAR]) {
VPRINTK("QUICK EXIT\n");
return IRQ_NONE;
}
mmio_base = host->iomap[PDC_MMIO_BAR];
spin_lock(&host->lock);
/* read and clear hotplug flags for all ports */
if (host->ports[0]->flags & PDC_FLAG_GEN_II)
hotplug_offset = PDC2_SATA_PLUG_CSR;
else
hotplug_offset = PDC_SATA_PLUG_CSR;
hotplug_status = readl(mmio_base + hotplug_offset);
if (hotplug_status & 0xff)
writel(hotplug_status | 0xff, mmio_base + hotplug_offset);
hotplug_status &= 0xff; /* clear uninteresting bits */
/* reading should also clear interrupts */
mask = readl(mmio_base + PDC_INT_SEQMASK);
if (mask == 0xffffffff && hotplug_status == 0) {
VPRINTK("QUICK EXIT 2\n");
goto done_irq;
}
mask &= 0xffff; /* only 16 tags possible */
if (mask == 0 && hotplug_status == 0) {
VPRINTK("QUICK EXIT 3\n");
goto done_irq;
}
writel(mask, mmio_base + PDC_INT_SEQMASK);
is_sataii_tx4 = pdc_is_sataii_tx4(host->ports[0]->flags);
for (i = 0; i < host->n_ports; i++) {
VPRINTK("port %u\n", i);
ap = host->ports[i];
/* check for a plug or unplug event */
ata_no = pdc_port_no_to_ata_no(i, is_sataii_tx4);
tmp = hotplug_status & (0x11 << ata_no);
if (tmp && ap &&
!(ap->flags & ATA_FLAG_DISABLED)) {
struct ata_eh_info *ehi = &ap->link.eh_info;
ata_ehi_clear_desc(ehi);
ata_ehi_hotplugged(ehi);
ata_ehi_push_desc(ehi, "hotplug_status %#x", tmp);
ata_port_freeze(ap);
++handled;
continue;
}
/* check for a packet interrupt */
tmp = mask & (1 << (i + 1));
if (tmp && ap &&
!(ap->flags & ATA_FLAG_DISABLED)) {
struct ata_queued_cmd *qc;
qc = ata_qc_from_tag(ap, ap->link.active_tag);
if (qc && (!(qc->tf.flags & ATA_TFLAG_POLLING)))
handled += pdc_host_intr(ap, qc);
}
}
VPRINTK("EXIT\n");
done_irq:
spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
}
static inline void pdc_packet_start(struct ata_queued_cmd *qc)
{
struct ata_port *ap = qc->ap;
struct pdc_port_priv *pp = ap->private_data;
void __iomem *mmio = ap->host->iomap[PDC_MMIO_BAR];
unsigned int port_no = ap->port_no;
u8 seq = (u8) (port_no + 1);
VPRINTK("ENTER, ap %p\n", ap);
writel(0x00000001, mmio + (seq * 4));
readl(mmio + (seq * 4)); /* flush */
pp->pkt[2] = seq;
wmb(); /* flush PRD, pkt writes */
writel(pp->pkt_dma, ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT);
readl(ap->ioaddr.cmd_addr + PDC_PKT_SUBMIT); /* flush */
}
static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc)
{
switch (qc->tf.protocol) {
case ATA_PROT_ATAPI_NODATA:
if (qc->dev->flags & ATA_DFLAG_CDB_INTR)
break;
/*FALLTHROUGH*/
case ATA_PROT_NODATA:
if (qc->tf.flags & ATA_TFLAG_POLLING)
break;
/*FALLTHROUGH*/
case ATA_PROT_ATAPI_DMA:
case ATA_PROT_DMA:
pdc_packet_start(qc);
return 0;
default:
break;
}
return ata_qc_issue_prot(qc);
}
static void pdc_tf_load_mmio(struct ata_port *ap, const struct
ata_taskfile *tf)
{
WARN_ON(tf->protocol == ATA_PROT_DMA ||
tf->protocol == ATA_PROT_ATAPI_DMA);
ata_tf_load(ap, tf);
}
static void pdc_exec_command_mmio(struct ata_port *ap,
const struct ata_taskfile *tf)
{
WARN_ON(tf->protocol == ATA_PROT_DMA ||
tf->protocol == ATA_PROT_ATAPI_DMA);
ata_exec_command(ap, tf);
}
static int pdc_check_atapi_dma(struct ata_queued_cmd *qc)
{
u8 *scsicmd = qc->scsicmd->cmnd;
int pio = 1; /* atapi dma off by default */
/* Whitelist commands that may use DMA. */
switch (scsicmd[0]) {
case WRITE_12:
case WRITE_10:
case WRITE_6:
case READ_12:
case READ_10:
case READ_6:
case 0xad: /* READ_DVD_STRUCTURE */
case 0xbe: /* READ_CD */
pio = 0;
}
/* -45150 (FFFF4FA2) to -1 (FFFFFFFF) shall use PIO mode */
if (scsicmd[0] == WRITE_10) {
unsigned int lba =
(scsicmd[2] << 24) |
(scsicmd[3] << 16) |
(scsicmd[4] << 8) |
scsicmd[5];
if (lba >= 0xFFFF4FA2)
pio = 1;
}
return pio;
}
static int pdc_old_sata_check_atapi_dma(struct ata_queued_cmd *qc)
{
/* First generation chips cannot use ATAPI DMA on SATA ports */
return 1;
}
static void pdc_ata_setup_port(struct ata_port *ap,
void __iomem *base, void __iomem *scr_addr)
{
ap->ioaddr.cmd_addr = base;
ap->ioaddr.data_addr = base;
ap->ioaddr.feature_addr =
ap->ioaddr.error_addr = base + 0x4;
ap->ioaddr.nsect_addr = base + 0x8;
ap->ioaddr.lbal_addr = base + 0xc;
ap->ioaddr.lbam_addr = base + 0x10;
ap->ioaddr.lbah_addr = base + 0x14;
ap->ioaddr.device_addr = base + 0x18;
ap->ioaddr.command_addr =
ap->ioaddr.status_addr = base + 0x1c;
ap->ioaddr.altstatus_addr =
ap->ioaddr.ctl_addr = base + 0x38;
ap->ioaddr.scr_addr = scr_addr;
}
static void pdc_host_init(struct ata_host *host)
{
void __iomem *mmio = host->iomap[PDC_MMIO_BAR];
int is_gen2 = host->ports[0]->flags & PDC_FLAG_GEN_II;
int hotplug_offset;
u32 tmp;
if (is_gen2)
hotplug_offset = PDC2_SATA_PLUG_CSR;
else
hotplug_offset = PDC_SATA_PLUG_CSR;
/*
* Except for the hotplug stuff, this is voodoo from the
* Promise driver. Label this entire section
* "TODO: figure out why we do this"
*/
/* enable BMR_BURST, maybe change FIFO_SHD to 8 dwords */
tmp = readl(mmio + PDC_FLASH_CTL);
tmp |= 0x02000; /* bit 13 (enable bmr burst) */
if (!is_gen2)
tmp |= 0x10000; /* bit 16 (fifo threshold at 8 dw) */
writel(tmp, mmio + PDC_FLASH_CTL);
/* clear plug/unplug flags for all ports */
tmp = readl(mmio + hotplug_offset);
writel(tmp | 0xff, mmio + hotplug_offset);
/* unmask plug/unplug ints */
tmp = readl(mmio + hotplug_offset);
writel(tmp & ~0xff0000, mmio + hotplug_offset);
/* don't initialise TBG or SLEW on 2nd generation chips */
if (is_gen2)
return;
/* reduce TBG clock to 133 Mhz. */
tmp = readl(mmio + PDC_TBG_MODE);
tmp &= ~0x30000; /* clear bit 17, 16*/
tmp |= 0x10000; /* set bit 17:16 = 0:1 */
writel(tmp, mmio + PDC_TBG_MODE);
readl(mmio + PDC_TBG_MODE); /* flush */
msleep(10);
/* adjust slew rate control register. */
tmp = readl(mmio + PDC_SLEW_CTL);
tmp &= 0xFFFFF03F; /* clear bit 11 ~ 6 */
tmp |= 0x00000900; /* set bit 11-9 = 100b , bit 8-6 = 100 */
writel(tmp, mmio + PDC_SLEW_CTL);
}
static int pdc_ata_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
static int printed_version;
const struct ata_port_info *pi = &pdc_port_info[ent->driver_data];
const struct ata_port_info *ppi[PDC_MAX_PORTS];
struct ata_host *host;
void __iomem *base;
int n_ports, i, rc;
int is_sataii_tx4;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
/* enable and acquire resources */
rc = pcim_enable_device(pdev);
if (rc)
return rc;
rc = pcim_iomap_regions(pdev, 1 << PDC_MMIO_BAR, DRV_NAME);
if (rc == -EBUSY)
pcim_pin_device(pdev);
if (rc)
return rc;
base = pcim_iomap_table(pdev)[PDC_MMIO_BAR];
/* determine port configuration and setup host */
n_ports = 2;
if (pi->flags & PDC_FLAG_4_PORTS)
n_ports = 4;
for (i = 0; i < n_ports; i++)
ppi[i] = pi;
if (pi->flags & PDC_FLAG_SATA_PATA) {
u8 tmp = readb(base + PDC_FLASH_CTL+1);
if (!(tmp & 0x80))
ppi[n_ports++] = pi + 1;
}
host = ata_host_alloc_pinfo(&pdev->dev, ppi, n_ports);
if (!host) {
dev_printk(KERN_ERR, &pdev->dev, "failed to allocate host\n");
return -ENOMEM;
}
host->iomap = pcim_iomap_table(pdev);
is_sataii_tx4 = pdc_is_sataii_tx4(pi->flags);
for (i = 0; i < host->n_ports; i++) {
struct ata_port *ap = host->ports[i];
unsigned int ata_no = pdc_port_no_to_ata_no(i, is_sataii_tx4);
unsigned int port_offset = 0x200 + ata_no * 0x80;
unsigned int scr_offset = 0x400 + ata_no * 0x100;
pdc_ata_setup_port(ap, base + port_offset, base + scr_offset);
ata_port_pbar_desc(ap, PDC_MMIO_BAR, -1, "mmio");
ata_port_pbar_desc(ap, PDC_MMIO_BAR, port_offset, "port");
}
/* initialize adapter */
pdc_host_init(host);
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
return rc;
/* start host, request IRQ and attach */
pci_set_master(pdev);
return ata_host_activate(host, pdev->irq, pdc_interrupt, IRQF_SHARED,
&pdc_ata_sht);
}
static int __init pdc_ata_init(void)
{
return pci_register_driver(&pdc_ata_pci_driver);
}
static void __exit pdc_ata_exit(void)
{
pci_unregister_driver(&pdc_ata_pci_driver);
}
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Promise ATA TX2/TX4/TX4000 low-level driver");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, pdc_ata_pci_tbl);
MODULE_VERSION(DRV_VERSION);
module_init(pdc_ata_init);
module_exit(pdc_ata_exit);
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work
2009-10-23 12:31 Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work Milan Burgdorf
@ 2009-10-23 13:19 ` Mikael Pettersson
2009-10-28 14:54 ` Milan Burgdorf
0 siblings, 1 reply; 4+ messages in thread
From: Mikael Pettersson @ 2009-10-23 13:19 UTC (permalink / raw)
To: Milan Burgdorf; +Cc: linux-ide
Milan Burgdorf writes:
> Dear Mr. Pettersson and the whole LINUX-IDE-team,
>
>
> I'm working with Xubuntu 8.04 by using Kernel 2.6.24-24-generic. My two
> 2,5-Zoll SATA-II-Harddisks are connected with a Promise SATA 300 TX2
> Plus-Controller.
>
> When the disks work with high I/O, than I become the similar problems
> like they are described in
>
> "http://marc.info/?l=linux-ide&m=121475606225101&w=2" and
> "http://marc.info/?l=linux-ide&m=120134441006713&w=2":
>
> Oct 15 20:20:46 alexandria-epia kernel: [ 5731.478618] res
> 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
> Oct 15 20:20:51 alexandria-epia kernel: [ 5736.825857] ata1: port is
> slow to respond, please be patient (Status 0xff)
> Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526446] ata1: device not
> ready (errno=-16), forcing hardreset
> Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526472] ata1: hard
> resetting link
> Oct 15 20:21:02 alexandria-epia kernel: [ 5747.713897] ata1: port is
> slow to respond, please be patient (Status 0xff)
> Oct 15 20:21:06 alexandria-epia kernel: [ 5751.575082] ata1: hard
> resetting link
> Oct 15 20:21:12 alexandria-epia kernel: [ 5757.762534] ata1: port is
> slow to respond, please be patient (Status 0xff)
> Oct 15 20:21:16 alexandria-epia kernel: [ 5761.623715] ata1: hard
> resetting link
> Oct 15 20:21:22 alexandria-epia kernel: [ 5767.811162] ata1: port is
> slow to respond, please be patient (Status 0xff)
> Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650099] ata1: limiting
> SATA link speed to 1.5 Gbps
> Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650114] ata1: hard
> resetting link
> Oct 15 20:21:56 alexandria-epia kernel: [ 5801.658417] ata1.00: disabled
Incomplete messages. Please post the full kernel log.
FWIW, the 2.6.32-rc kernel has updates for the controller reset operations
which may help get stubborn disks back on line. That patch is available
for 2.6.28 to 2.6.31 kernels in the patch repository you mention below.
> To solve my problem I patched the sata_promise-Module with your three
> patches from "http://user.it.uu.se/~mikpe/linux/patches/2.6/OLD/2.6.24/"
> and installed the new module.
>
> After this I checked hopefully my /var/log/messages, but the disk run
> anymore in 3.0GB/s-Mode, and again I become the I/O-problems:
Incomplete messages. In particular, the limit-sataii-to-1.5Gbps
patch has a printk() which is missing here.
> Is there another possibility to force the Promise-Controller down to 1.5
> GB/s?
Libata has a generic libata.force= parameter which can be used to tweak
various settings, including 1.5Gbps vs 3Gbps. I haven't used it myself,
but see Documentation/kernel-parameters.txt for details.
/Mikael
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work
2009-10-23 13:19 ` Mikael Pettersson
@ 2009-10-28 14:54 ` Milan Burgdorf
2009-11-01 15:44 ` Milan Burgdorf
0 siblings, 1 reply; 4+ messages in thread
From: Milan Burgdorf @ 2009-10-28 14:54 UTC (permalink / raw)
To: linux-ide
> > Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650099] ata1: limiting
> > SATA link speed to 1.5 Gbps
> > Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650114] ata1: hard
> > resetting link
> > Oct 15 20:21:56 alexandria-epia kernel: [ 5801.658417] ata1.00: disabled
>
> Incomplete messages. Please post the full kernel log.
Thank you for the quick answer!!!
Here is the log of the 15.10.:
Oct 15 18:56:56 alexandria-epia syslogd 1.5.0#1ubuntu1: restart.
Oct 15 18:56:56 alexandria-epia kernel: Inspecting
/boot/System.map-2.6.24-24-generic
Oct 15 18:56:57 alexandria-epia kernel: Loaded 27922 symbols from
/boot/System.map-2.6.24-24-generic.
Oct 15 18:56:57 alexandria-epia kernel: Symbols match kernel version 2.6.24.
Oct 15 18:56:57 alexandria-epia kernel: Loaded 14462 symbols from 72
modules.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Initializing
cgroup subsys cpuset
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Initializing
cgroup subsys cpu
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Linux version
2.6.24-24-generic (buildd@palmer) (gcc version 4.2.4 (Ubuntu
4.2.4-1ubuntu4)) #1 SMP Fri Sep 18 16:49:39 UTC 2009 (Ubuntu
2.6.24-24.61-generic)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-provided
physical RAM map:
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
0000000000000000 - 00000000000a0000 (usable)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
00000000000f0000 - 0000000000100000 (reserved)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
0000000000100000 - 000000001eff0000 (usable)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
000000001eff0000 - 000000001eff3000 (ACPI NVS)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
000000001eff3000 - 000000001f000000 (ACPI data)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] BIOS-e820:
00000000ffff0000 - 0000000100000000 (reserved)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] 0MB HIGHMEM
available.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] 495MB LOWMEM
available.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Zone PFN ranges:
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] DMA
0 -> 4096
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Normal
4096 -> 126960
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] HighMem
126960 -> 126960
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Movable zone
start PFN for each node
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] early_node_map[1]
active PFN ranges
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] 0: 0
-> 126960
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] DMI 2.2 present.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: RSDP
signature @ 0xC00F6620 checksum 0
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: RSDP
000F6620, 0014 (r0 VT9174)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: RSDT
1EFF3000, 0028 (r1 VT9174 AWRDACPI 42302E31 AWRD 0)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: FACP
1EFF3040, 0074 (r1 VT9174 AWRDACPI 42302E31 AWRD 0)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: DSDT
1EFF30C0, 2FDD (r1 VT9174 AWRDACPI 1000 MSFT 100000C)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: FACS
1EFF0000, 0040
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] ACPI: PM-Timer IO
Port: 0x408
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Allocating PCI
resources starting at 20000000 (gap: 1f000000:e0ff0000)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] swsusp:
Registered nosave memory region: 00000000000a0000 - 00000000000f0000
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] swsusp:
Registered nosave memory region: 00000000000f0000 - 0000000000100000
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Built 1 zonelists
in Zone order, mobility grouping on. Total pages: 125969
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Kernel command
line: root=UUID=aaa9e2d6-6d42-4ea3-a1e4-2427daef47d9 ro
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] No local APIC
present or hardware disabled
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Enabling fast FPU
save and restore... done.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Enabling unmasked
SIMD FPU exception support... done.
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Initializing CPU#0
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] PID hash table
entries: 2048 (order: 11, 8192 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 0.000000] Detected 999.848
MHz processor.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.672310] Console: colour
VGA+ 80x25
Oct 15 18:56:57 alexandria-epia kernel: [ 18.672320] console [tty0]
enabled
Oct 15 18:56:57 alexandria-epia kernel: [ 18.674996] Dentry cache hash
table entries: 65536 (order: 6, 262144 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.676903] Inode-cache hash
table entries: 32768 (order: 5, 131072 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754529] Memory:
491384k/507840k available (2181k kernel code, 15880k reserved, 1006k
data, 368k init, 0k highmem)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754624] virtual kernel
memory layout:
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754628] fixmap :
0xfff4b000 - 0xfffff000 ( 720 kB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754633] pkmap :
0xff800000 - 0xffc00000 (4096 kB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754638] vmalloc :
0xdf800000 - 0xff7fe000 ( 511 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754643] lowmem :
0xc0000000 - 0xdeff0000 ( 495 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754648] .init :
0xc0423000 - 0xc047f000 ( 368 kB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754653] .data :
0xc0321548 - 0xc041cdc4 (1006 kB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.754657] .text :
0xc0100000 - 0xc0321548 (2181 kB)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755003] Checking if this
processor honours the WP bit even in supervisor mode... Ok.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755181] SLUB:
Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755290] Calibrating delay
loop (skipped), using tsc calculated value.. 1999.69 BogoMIPS (lpj=3999392)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755437] Security
Framework initialized
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755494] SELinux:
Disabled at boot.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755583] AppArmor:
AppArmor initialized
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755636] Failure
registering capabilities with primary security module.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.755704] Mount-cache hash
table entries: 512
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756007] Initializing
cgroup subsys ns
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756059] Initializing
cgroup subsys cpuacct
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756148] CPU: L1 I Cache:
64K (32 bytes/line), D cache 64K (32 bytes/line)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756202] CPU: L2 Cache:
64K (32 bytes/line)
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756279] Compat vDSO
mapped to ffffe000.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.756353] Checking 'hlt'
instruction... OK.
Oct 15 18:56:57 alexandria-epia kernel: [ 18.771908] SMP alternatives:
switching to UP code
Oct 15 18:56:57 alexandria-epia kernel: [ 18.774581] Freeing SMP
alternatives: 11k freed
Oct 15 18:56:57 alexandria-epia kernel: [ 18.774997] Early unpacking
initramfs... done
Oct 15 18:56:57 alexandria-epia kernel: [ 20.060351] ACPI: Core
revision 20070126
Oct 15 18:56:57 alexandria-epia kernel: [ 20.060632] ACPI: Looking for
DSDT in initramfs... error, file /DSDT.aml not found.
Oct 15 18:56:57 alexandria-epia kernel: [ 20.064765] ACPI: setting
ELCR to 0200 (from 1e20)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.067498] CPU0: Centaur VIA
Nehemiah stepping 05
Oct 15 18:56:57 alexandria-epia kernel: [ 20.067630] SMP motherboard
not detected.
Oct 15 18:56:57 alexandria-epia kernel: [ 20.067676] Local APIC not
detected. Using dummy APIC emulation.
Oct 15 18:56:57 alexandria-epia kernel: [ 20.067841] Brought up 1 CPUs
Oct 15 18:56:57 alexandria-epia kernel: [ 20.068463] net_namespace: 64
bytes
Oct 15 18:56:57 alexandria-epia kernel: [ 20.068528] Booting
paravirtualized kernel on bare hardware
Oct 15 18:56:57 alexandria-epia kernel: [ 20.069860] Time: 16:56:02
Date: 10/15/09
Oct 15 18:56:57 alexandria-epia kernel: [ 20.069994] NET: Registered
protocol family 16
Oct 15 18:56:57 alexandria-epia kernel: [ 20.070577] EISA bus registered
Oct 15 18:56:57 alexandria-epia kernel: [ 20.070645] ACPI: bus type
pci registered
Oct 15 18:56:57 alexandria-epia kernel: [ 20.100591] PCI: PCI BIOS
revision 2.10 entry at 0xfb260, last bus=1
Oct 15 18:56:57 alexandria-epia kernel: [ 20.100646] PCI: Using
configuration type 1
Oct 15 18:56:57 alexandria-epia kernel: [ 20.100716] Setting up
standard PCI resources
Oct 15 18:56:57 alexandria-epia kernel: [ 20.122784] ACPI: Interpreter
enabled
Oct 15 18:56:57 alexandria-epia kernel: [ 20.122846] ACPI: (supports
S0 S1 S4 S5)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.123023] ACPI: Using PIC
for interrupt routing
Oct 15 18:56:57 alexandria-epia kernel: [ 20.131347] ACPI: PCI Root
Bridge [PCI0] (0000:00)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.132033] PCI quirk: region
0400-047f claimed by vt8235 PM
Oct 15 18:56:57 alexandria-epia kernel: [ 20.132086] PCI quirk: region
0500-050f claimed by vt8235 SMB
Oct 15 18:56:57 alexandria-epia kernel: [ 20.169711] ACPI: PCI
Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.170525] ACPI: PCI
Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.171374] ACPI: PCI
Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.172179] ACPI: PCI
Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.172921] Linux Plug and
Play Support v0.97 (c) Adam Belay
Oct 15 18:56:57 alexandria-epia kernel: [ 20.173051] pnp: PnP ACPI init
Oct 15 18:56:57 alexandria-epia kernel: [ 20.173114] ACPI: bus type
pnp registered
Oct 15 18:56:57 alexandria-epia kernel: [ 20.178116] pnp: PnP ACPI:
found 9 devices
Oct 15 18:56:57 alexandria-epia kernel: [ 20.178177] ACPI: ACPI bus
type pnp unregistered
Oct 15 18:56:57 alexandria-epia kernel: [ 20.178230] PnPBIOS: Disabled
by ACPI PNP
Oct 15 18:56:57 alexandria-epia kernel: [ 20.178872] PCI: Using ACPI
for IRQ routing
Oct 15 18:56:57 alexandria-epia kernel: [ 20.178927] PCI: If a device
doesn't work, try "pci=routeirq". If it helps, post a report
Oct 15 18:56:57 alexandria-epia kernel: [ 20.251107] NET: Registered
protocol family 8
Oct 15 18:56:57 alexandria-epia kernel: [ 20.251159] NET: Registered
protocol family 20
Oct 15 18:56:57 alexandria-epia kernel: [ 20.251398] AppArmor:
AppArmor Filesystem Enabled
Oct 15 18:56:57 alexandria-epia kernel: [ 20.255091] Time: tsc
clocksource has been installed.
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263211] system 00:00:
iomem range 0xd0000-0xd3fff has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263268] system 00:00:
iomem range 0xdd000-0xdffff has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263323] system 00:00:
iomem range 0xf0000-0xfbfff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263378] system 00:00:
iomem range 0xfc000-0xfffff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263434] system 00:00:
iomem range 0x1eff0000-0x1effffff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263499] system 00:00:
iomem range 0xffff0000-0xffffffff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263563] system 00:00:
iomem range 0x0-0x9ffff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263617] system 00:00:
iomem range 0x100000-0x1efeffff could not be reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263680] system 00:00:
iomem range 0xfee00000-0xfee00fff has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263736] system 00:00:
iomem range 0xfff80000-0xfffeffff has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263804] system 00:02:
ioport range 0x400-0x47f has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263858] system 00:02:
ioport range 0x500-0x50f has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.263926] system 00:03:
ioport range 0x4d0-0x4d1 has been reserved
Oct 15 18:56:57 alexandria-epia kernel: [ 20.295066] PCI: Bridge:
0000:00:01.0
Oct 15 18:56:57 alexandria-epia kernel: [ 20.295128] IO window:
disabled.
Oct 15 18:56:57 alexandria-epia kernel: [ 20.295178] MEM window:
e4000000-e5ffffff
Oct 15 18:56:57 alexandria-epia kernel: [ 20.295227] PREFETCH
window: e0000000-e3ffffff
Oct 15 18:56:57 alexandria-epia kernel: [ 20.295341] NET: Registered
protocol family 2
Oct 15 18:56:57 alexandria-epia kernel: [ 20.335345] IP route cache
hash table entries: 4096 (order: 2, 16384 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.336109] TCP established
hash table entries: 16384 (order: 5, 131072 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.336667] TCP bind hash
table entries: 16384 (order: 5, 131072 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.337321] TCP: Hash tables
configured (established 16384 bind 16384)
Oct 15 18:56:57 alexandria-epia kernel: [ 20.337379] TCP reno registered
Oct 15 18:56:57 alexandria-epia kernel: [ 20.347537] checking if image
is initramfs...<7>Switched to high resolution mode on CPU 0
Oct 15 18:56:57 alexandria-epia kernel: [ 21.506992] it is
Oct 15 18:56:57 alexandria-epia kernel: [ 22.833479] Freeing initrd
memory: 7350k freed
Oct 15 18:56:57 alexandria-epia kernel: [ 22.834825] audit:
initializing netlink socket (disabled)
Oct 15 18:56:57 alexandria-epia kernel: [ 22.834912]
audit(1255625764.080:1): initialized
Oct 15 18:56:57 alexandria-epia kernel: [ 22.840877] VFS: Disk quotas
dquot_6.5.1
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841187] Dquot-cache hash
table entries: 1024 (order 0, 4096 bytes)
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841648] io scheduler noop
registered
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841697] io scheduler
anticipatory registered
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841744] io scheduler
deadline registered
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841820] io scheduler cfq
registered (default)
Oct 15 18:56:57 alexandria-epia kernel: [ 22.841891] PCI: VIA PCI
bridge detected. Disabling DAC.
Oct 15 18:56:57 alexandria-epia kernel: [ 22.842729] isapnp: Scanning
for PnP cards...
Oct 15 18:56:57 alexandria-epia kernel: [ 23.196460] isapnp: No Plug &
Play device found
Oct 15 18:56:57 alexandria-epia kernel: [ 23.285886] Real Time Clock
Driver v1.12ac
Oct 15 18:56:57 alexandria-epia kernel: [ 23.286164] Serial:
8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Oct 15 18:56:57 alexandria-epia kernel: [ 23.289275] RAMDISK driver
initialized: 16 RAM disks of 65536K size 1024 blocksize
Oct 15 18:56:57 alexandria-epia kernel: [ 23.289565] input: Macintosh
mouse button emulation as /devices/virtual/input/input0
Oct 15 18:56:57 alexandria-epia kernel: [ 23.289990] PNP: No PS/2
controller found. Probing ports directly.
Oct 15 18:56:57 alexandria-epia kernel: [ 23.542448] serio: i8042 KBD
port at 0x60,0x64 irq 1
Oct 15 18:56:57 alexandria-epia kernel: [ 23.554522] mice: PS/2 mouse
device common for all mice
Oct 15 18:56:57 alexandria-epia kernel: [ 23.554865] EISA: Probing bus
0 at eisa.0
Oct 15 18:56:57 alexandria-epia kernel: [ 23.554965] EISA: Detected 0
cards.
Oct 15 18:56:57 alexandria-epia kernel: [ 23.555012] cpuidle: using
governor ladder
Oct 15 18:56:57 alexandria-epia kernel: [ 23.555058] cpuidle: using
governor menu
Oct 15 18:56:57 alexandria-epia kernel: [ 23.555574] NET: Registered
protocol family 1
Oct 15 18:56:57 alexandria-epia kernel: [ 23.555699] Using IPI
No-Shortcut mode
Oct 15 18:56:57 alexandria-epia kernel: [ 23.555815] registered
taskstats version 1
Oct 15 18:56:57 alexandria-epia kernel: [ 23.556121] Magic number:
13:738:944
Oct 15 18:56:57 alexandria-epia kernel: [ 23.556333] hash matches
device ptyyf
Oct 15 18:56:57 alexandria-epia kernel: [ 23.556472] hash matches
device tty1
Oct 15 18:56:57 alexandria-epia kernel: [ 23.556562] BIOS EDD facility
v0.16 2004-Jun-25, 0 devices found
Oct 15 18:56:57 alexandria-epia kernel: [ 23.556611] EDD information
not available.
Oct 15 18:56:57 alexandria-epia kernel: [ 23.558195] Freeing unused
kernel memory: 368k freed
Oct 15 18:56:57 alexandria-epia kernel: [ 23.558436] Write protecting
the kernel read-only data: 802k
Oct 15 18:56:57 alexandria-epia kernel: [ 24.259182] fuse init (API
version 7.9)
Oct 15 18:56:57 alexandria-epia kernel: [ 24.334449] ACPI: CPU0 (power
states: C1[C1] C2[C2])
Oct 15 18:56:57 alexandria-epia kernel: [ 24.334594] ACPI: Processor
[CPU0] (supports 2 throttling states)
Oct 15 18:56:57 alexandria-epia kernel: [ 25.498784] usbcore:
registered new interface driver usbfs
Oct 15 18:56:57 alexandria-epia kernel: [ 25.498896] usbcore:
registered new interface driver hub
Oct 15 18:56:57 alexandria-epia kernel: [ 25.533893] ACPI: PCI
Interrupt Link [LNKB] enabled at IRQ 10
Oct 15 18:56:57 alexandria-epia kernel: [ 25.534011] ACPI: PCI
Interrupt 0000:00:0d.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
Oct 15 18:56:57 alexandria-epia kernel: [ 25.587087] ohci1394:
fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[e8022000-e80227ff] Max
Packet=[2048] IR/IT contexts=[4/8]
Oct 15 18:56:57 alexandria-epia kernel: [ 25.630320] usbcore:
registered new device driver usb
Oct 15 18:56:57 alexandria-epia kernel: [ 25.666028] USB Universal
Host Controller Interface driver v3.0
Oct 15 18:56:57 alexandria-epia kernel: [ 26.032612] SCSI subsystem
initialized
Oct 15 18:56:57 alexandria-epia kernel: [ 26.057799] ACPI: PCI
Interrupt Link [LNKA] enabled at IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 26.057919] ACPI: PCI
Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 26.058052] uhci_hcd
0000:00:10.0: UHCI Host Controller
Oct 15 18:56:57 alexandria-epia kernel: [ 26.058822] uhci_hcd
0000:00:10.0: new USB bus registered, assigned bus number 1
Oct 15 18:56:57 alexandria-epia kernel: [ 26.058923] uhci_hcd
0000:00:10.0: irq 11, io base 0x0000d400
Oct 15 18:56:57 alexandria-epia kernel: [ 26.059395] usb usb1:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 26.059502] hub 1-0:1.0: USB
hub found
Oct 15 18:56:57 alexandria-epia kernel: [ 26.059555] hub 1-0:1.0: 2
ports detected
Oct 15 18:56:57 alexandria-epia kernel: [ 26.133922]
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
Oct 15 18:56:57 alexandria-epia kernel: [ 26.133997] via-rhine: Broken
BIOS detected, avoid_D3 enabled.
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162106] ACPI: PCI
Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162254] uhci_hcd
0000:00:10.1: UHCI Host Controller
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162363] uhci_hcd
0000:00:10.1: new USB bus registered, assigned bus number 2
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162456] uhci_hcd
0000:00:10.1: irq 10, io base 0x0000d800
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162844] usb usb2:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 26.162949] hub 2-0:1.0: USB
hub found
Oct 15 18:56:57 alexandria-epia kernel: [ 26.163003] hub 2-0:1.0: 2
ports detected
Oct 15 18:56:57 alexandria-epia kernel: [ 26.266971] ACPI: PCI
Interrupt Link [LNKC] enabled at IRQ 5
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267047] ACPI: PCI
Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267180] uhci_hcd
0000:00:10.2: UHCI Host Controller
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267311] uhci_hcd
0000:00:10.2: new USB bus registered, assigned bus number 3
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267407] uhci_hcd
0000:00:10.2: irq 5, io base 0x0000dc00
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267810] usb usb3:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267918] hub 3-0:1.0: USB
hub found
Oct 15 18:56:57 alexandria-epia kernel: [ 26.267972] hub 3-0:1.0: 2
ports detected
Oct 15 18:56:57 alexandria-epia kernel: [ 26.371419] ACPI: PCI
Interrupt Link [LNKD] enabled at IRQ 12
Oct 15 18:56:57 alexandria-epia kernel: [ 26.371496] ACPI: PCI
Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
Oct 15 18:56:57 alexandria-epia kernel: [ 26.371635] ehci_hcd
0000:00:10.3: EHCI Host Controller
Oct 15 18:56:57 alexandria-epia kernel: [ 26.371771] ehci_hcd
0000:00:10.3: new USB bus registered, assigned bus number 4
Oct 15 18:56:57 alexandria-epia kernel: [ 26.371932] ehci_hcd
0000:00:10.3: irq 12, io mem 0xe8023000
Oct 15 18:56:57 alexandria-epia kernel: [ 26.401837] usb 1-1: new low
speed USB device using uhci_hcd and address 2
Oct 15 18:56:57 alexandria-epia kernel: [ 26.413992] ehci_hcd
0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Oct 15 18:56:57 alexandria-epia kernel: [ 26.414397] usb usb4:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 26.414508] hub 4-0:1.0: USB
hub found
Oct 15 18:56:57 alexandria-epia kernel: [ 26.414565] hub 4-0:1.0: 6
ports detected
Oct 15 18:56:57 alexandria-epia kernel: [ 26.518519] ACPI: PCI
Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 26.523306] eth0: VIA Rhine
II at 0xe8020000, 00:40:63:db:17:22, IRQ 11.
Oct 15 18:56:57 alexandria-epia kernel: [ 26.524070] eth0: MII PHY
found at address 1, status 0x786d advertising 05e1 Link 45e1.
Oct 15 18:56:57 alexandria-epia kernel: [ 26.525703] ACPI: PCI
Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 26.525900] PCI: VIA VLink
IRQ fixup for 0000:00:11.1, from 255 to 11
Oct 15 18:56:57 alexandria-epia kernel: [ 26.526109] ACPI: PCI
interrupt for device 0000:00:11.1 disabled
Oct 15 18:56:57 alexandria-epia kernel: [ 26.529850] ACPI: PCI
Interrupt 0000:00:14.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
Oct 15 18:56:57 alexandria-epia kernel: [ 26.553830] scsi0 : sata_promise
Oct 15 18:56:57 alexandria-epia kernel: [ 26.580918] scsi1 : sata_promise
Oct 15 18:56:57 alexandria-epia kernel: [ 26.598580] scsi2 : sata_promise
Oct 15 18:56:57 alexandria-epia kernel: [ 26.598772] ata1: SATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021200 irq 10
Oct 15 18:56:57 alexandria-epia kernel: [ 26.598837] ata2: SATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021280 irq 10
Oct 15 18:56:57 alexandria-epia kernel: [ 26.598899] ata3: PATA max
UDMA/133 mmio m4096@0xe8021000 port 0xe8021300 irq 10
Oct 15 18:56:57 alexandria-epia kernel: [ 27.065722] ata1: SATA link
up 3.0 Gbps (SStatus 123 SControl 300)
Oct 15 18:56:57 alexandria-epia kernel: [ 27.118145] ata1.00: ATA-8:
WDC WD2500BEVT-22ZCT0, 11.01A11, max UDMA/133
Oct 15 18:56:57 alexandria-epia kernel: [ 27.118216] ata1.00:
488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
Oct 15 18:56:57 alexandria-epia kernel: [ 27.134959] ata1.00:
configured for UDMA/133
Oct 15 18:56:57 alexandria-epia kernel: [ 27.601623] ata2: SATA link
up 3.0 Gbps (SStatus 123 SControl 300)
Oct 15 18:56:57 alexandria-epia kernel: [ 27.609927] ata2.00: ATA-8:
ST9250827AS, 3.AAA, max UDMA/133
Oct 15 18:56:57 alexandria-epia kernel: [ 27.609993] ata2.00:
488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
Oct 15 18:56:57 alexandria-epia kernel: [ 27.625907] ata2.00:
configured for UDMA/133
Oct 15 18:56:57 alexandria-epia kernel: [ 27.721591] usb 1-1: new low
speed USB device using uhci_hcd and address 3
Oct 15 18:56:57 alexandria-epia kernel: [ 27.781933] scsi 0:0:0:0:
Direct-Access ATA WDC WD2500BEVT-2 11.0 PQ: 0 ANSI: 5
Oct 15 18:56:57 alexandria-epia kernel: [ 27.782504] scsi 1:0:0:0:
Direct-Access ATA ST9250827AS 3.AA PQ: 0 ANSI: 5
Oct 15 18:56:57 alexandria-epia kernel: [ 27.783265] ACPI: PCI
Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 27.783394] PCI: VIA VLink
IRQ fixup for 0000:00:11.1, from 255 to 11
Oct 15 18:56:57 alexandria-epia kernel: [ 27.786271] scsi3 : pata_via
Oct 15 18:56:57 alexandria-epia kernel: [ 27.788881] scsi4 : pata_via
Oct 15 18:56:57 alexandria-epia kernel: [ 27.794354] ata4: PATA max
UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
Oct 15 18:56:57 alexandria-epia kernel: [ 27.794414] ata5: PATA max
UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
Oct 15 18:56:57 alexandria-epia kernel: [ 27.879844] usb 1-1:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 27.958143] ata4.00: ATA-6:
IC25N030ATMR04-0, MOAOAD4A, max UDMA/100
Oct 15 18:56:57 alexandria-epia kernel: [ 27.958213] ata4.00: 58605120
sectors, multi 16: LBA
Oct 15 18:56:57 alexandria-epia kernel: [ 27.974023] ata4.00:
configured for UDMA/100
Oct 15 18:56:57 alexandria-epia kernel: [ 28.121519] usb 1-2: new low
speed USB device using uhci_hcd and address 4
Oct 15 18:56:57 alexandria-epia kernel: [ 28.293858] ata5.00: ATAPI:
HL-DT-ST DVDRAM GSA-4167B, DL13, max UDMA/33
Oct 15 18:56:57 alexandria-epia kernel: [ 28.296638] usb 1-2:
configuration #1 chosen from 1 choice
Oct 15 18:56:57 alexandria-epia kernel: [ 28.465681] ata5.00:
configured for UDMA/33
Oct 15 18:56:57 alexandria-epia kernel: [ 28.466019] scsi 3:0:0:0:
Direct-Access ATA IC25N030ATMR04-0 MOAO PQ: 0 ANSI: 5
Oct 15 18:56:57 alexandria-epia kernel: [ 28.471527] scsi 4:0:0:0:
CD-ROM HL-DT-ST DVDRAM GSA-4167B DL13 PQ: 0 ANSI: 5
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479280] Driver 'sd' needs
updating - please use bus_type methods
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479540] sd 0:0:0:0: [sda]
488397168 512-byte hardware sectors (250059 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479616] sd 0:0:0:0: [sda]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479708] sd 0:0:0:0: [sda]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479886] sd 0:0:0:0: [sda]
488397168 512-byte hardware sectors (250059 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.479957] sd 0:0:0:0: [sda]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.480044] sd 0:0:0:0: [sda]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.480111] sda: sda1 < sda5 >
Oct 15 18:56:57 alexandria-epia kernel: [ 28.494813] sd 0:0:0:0: [sda]
Attached SCSI disk
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495037] sd 1:0:0:0: [sdb]
488397168 512-byte hardware sectors (250059 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495114] sd 1:0:0:0: [sdb]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495206] sd 1:0:0:0: [sdb]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495377] sd 1:0:0:0: [sdb]
488397168 512-byte hardware sectors (250059 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495448] sd 1:0:0:0: [sdb]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.495535] sd 1:0:0:0: [sdb]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.496808] sdb: sdb1 < sdb5 >
Oct 15 18:56:57 alexandria-epia kernel: [ 28.514465] sd 1:0:0:0: [sdb]
Attached SCSI disk
Oct 15 18:56:57 alexandria-epia kernel: [ 28.514667] sd 3:0:0:0: [sdc]
58605120 512-byte hardware sectors (30006 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.514743] sd 3:0:0:0: [sdc]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.514836] sd 3:0:0:0: [sdc]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.515000] sd 3:0:0:0: [sdc]
58605120 512-byte hardware sectors (30006 MB)
Oct 15 18:56:57 alexandria-epia kernel: [ 28.515070] sd 3:0:0:0: [sdc]
Write Protect is off
Oct 15 18:56:57 alexandria-epia kernel: [ 28.515157] sd 3:0:0:0: [sdc]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 18:56:57 alexandria-epia kernel: [ 28.515224] sdc: sdc1 sdc2
Oct 15 18:56:57 alexandria-epia kernel: [ 28.571981] sd 3:0:0:0: [sdc]
Attached SCSI disk
Oct 15 18:56:57 alexandria-epia kernel: [ 28.621584] sd 0:0:0:0:
Attached scsi generic sg0 type 0
Oct 15 18:56:57 alexandria-epia kernel: [ 28.621694] sd 1:0:0:0:
Attached scsi generic sg1 type 0
Oct 15 18:56:57 alexandria-epia kernel: [ 28.621789] sd 3:0:0:0:
Attached scsi generic sg2 type 0
Oct 15 18:56:57 alexandria-epia kernel: [ 28.621880] scsi 4:0:0:0:
Attached scsi generic sg3 type 5
Oct 15 18:56:57 alexandria-epia kernel: [ 28.710624] usbcore:
registered new interface driver hiddev
Oct 15 18:56:57 alexandria-epia kernel: [ 28.738030] input: HID
046a:002b as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.0/input/input1
Oct 15 18:56:57 alexandria-epia kernel: [ 28.753480] input,hidraw0:
USB HID v1.11 Keyboard [HID 046a:002b] on usb-0000:00:10.0-1
Oct 15 18:56:57 alexandria-epia kernel: [ 28.757397] Driver 'sr' needs
updating - please use bus_type methods
Oct 15 18:56:57 alexandria-epia kernel: [ 28.774596] input: HID
046a:002b as /devices/pci0000:00/0000:00:10.0/usb1/1-1/1-1:1.1/input/input2
Oct 15 18:56:57 alexandria-epia kernel: [ 28.778913] sr0: scsi3-mmc
drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Oct 15 18:56:57 alexandria-epia kernel: [ 28.778989] Uniform CD-ROM
driver Revision: 3.20
Oct 15 18:56:57 alexandria-epia kernel: [ 28.789409] input,hidraw1:
USB HID v1.11 Device [HID 046a:002b] on usb-0000:00:10.0-1
Oct 15 18:56:57 alexandria-epia kernel: [ 28.806896] input: Logitech
USB Receiver as
/devices/pci0000:00/0000:00:10.0/usb1/1-2/1-2:1.0/input/input3
Oct 15 18:56:57 alexandria-epia kernel: [ 28.817485] input,hidraw2:
USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:10.0-2
Oct 15 18:56:57 alexandria-epia kernel: [ 28.817703] usbcore:
registered new interface driver usbhid
Oct 15 18:56:57 alexandria-epia kernel: [ 28.817757]
/build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID
core driver
Oct 15 18:56:57 alexandria-epia kernel: [ 34.800905] kjournald
starting. Commit interval 5 seconds
Oct 15 18:56:57 alexandria-epia kernel: [ 34.800992] EXT3-fs: mounted
filesystem with ordered data mode.
Oct 15 18:56:57 alexandria-epia kernel: [ 52.576399] Linux agpgart
interface v0.102
Oct 15 18:56:57 alexandria-epia kernel: [ 52.692458] pci_hotplug: PCI
Hot Plug PCI Core version: 0.5
Oct 15 18:56:57 alexandria-epia kernel: [ 52.758980] shpchp: Standard
Hot Plug PCI Controller Driver version: 0.4
Oct 15 18:56:57 alexandria-epia kernel: [ 52.832535] agpgart: Detected
VIA CLE266 chipset
Oct 15 18:56:57 alexandria-epia kernel: [ 52.834296] agpgart: AGP
aperture is 16M @ 0xe6000000
Oct 15 18:56:57 alexandria-epia kernel: [ 53.320410] input: PC Speaker
as /devices/platform/pcspkr/input/input4
Oct 15 18:56:57 alexandria-epia kernel: [ 53.752220] NET: Registered
protocol family 23
Oct 15 18:56:57 alexandria-epia kernel: [ 54.900348] input: Power
Button (FF) as /devices/virtual/input/input5
Oct 15 18:56:57 alexandria-epia kernel: [ 54.911849] ACPI: Power
Button (FF) [PWRF]
Oct 15 18:56:57 alexandria-epia kernel: [ 54.912203] input: Power
Button (CM) as /devices/virtual/input/input6
Oct 15 18:56:57 alexandria-epia kernel: [ 54.927821] ACPI: Power
Button (CM) [PWRB]
Oct 15 18:56:57 alexandria-epia kernel: [ 55.478425] eth0: link up,
100Mbps, full-duplex, lpa 0x45E1
Oct 15 18:56:57 alexandria-epia kernel: [ 55.711987] ACPI: PCI
Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Oct 15 18:56:57 alexandria-epia kernel: [ 56.995845] Console:
switching to colour frame buffer device 80x30
Oct 15 18:56:57 alexandria-epia kernel: [ 56.998564] fb0: VIA VT8623
on 0000:01:00.0, 16 MB RAM
Oct 15 18:56:57 alexandria-epia kernel: [ 59.699555] NET: Registered
protocol family 10
Oct 15 18:56:57 alexandria-epia kernel: [ 59.700272] lo: Disabled
Privacy Extensions
Oct 15 18:56:57 alexandria-epia kernel: [ 65.255719] lp: driver loaded
but no devices found
Oct 15 18:56:57 alexandria-epia kernel: [ 65.457876] vt1211: Found
VT1211 chip at 0x6000, revision 2
Oct 15 18:56:57 alexandria-epia kernel: [ 66.168643] Adding 1959920k
swap on /dev/sdc2. Priority:-1 extents:1 across:1959920k
Oct 15 18:56:57 alexandria-epia kernel: [ 66.719515] EXT3 FS on sdc1,
internal journal
Oct 15 18:56:57 alexandria-epia kernel: [ 69.027766] kjournald
starting. Commit interval 5 seconds
Oct 15 18:56:57 alexandria-epia kernel: [ 69.033492] EXT3 FS on sda5,
internal journal
Oct 15 18:56:57 alexandria-epia kernel: [ 69.033507] EXT3-fs: mounted
filesystem with ordered data mode.
Oct 15 18:56:57 alexandria-epia kernel: [ 69.059687] kjournald
starting. Commit interval 5 seconds
Oct 15 18:56:57 alexandria-epia kernel: [ 69.065353] EXT3 FS on sdb5,
internal journal
Oct 15 18:56:57 alexandria-epia kernel: [ 69.065367] EXT3-fs: mounted
filesystem with ordered data mode.
Oct 15 18:56:57 alexandria-epia kernel: [ 70.441875] ip_tables: (C)
2000-2006 Netfilter Core Team
Oct 15 18:56:57 alexandria-epia kernel: [ 73.474457] No dock devices
found.
Oct 15 18:56:57 alexandria-epia kernel: [ 74.285889] longhaul: VIA C3
'Nehemiah C' [C5P] CPU detected. Powersaver supported.
Oct 15 18:56:57 alexandria-epia kernel: [ 74.285923] longhaul: ACPI
I/O at 0x400
Oct 15 18:56:57 alexandria-epia kernel: [ 74.285963] longhaul: Using
northbridge support.
Oct 15 18:56:57 alexandria-epia kernel: [ 74.285970] longhaul: Using
ACPI support.
Oct 15 18:56:58 alexandria-epia kernel: [ 76.476357] apm: BIOS version
1.2 Flags 0x07 (Driver version 1.16ac)
Oct 15 18:56:58 alexandria-epia kernel: [ 76.476373] apm: overridden
by ACPI.
Oct 15 18:56:59 alexandria-epia kernel: [ 116.274084] Marking TSC
unstable due to: cpufreq changes.
Oct 15 18:56:59 alexandria-epia kernel: [ 116.275897] Time: acpi_pm
clocksource has been installed.
Oct 15 18:56:59 alexandria-epia kernel: [ 116.487422] Clocksource tsc
unstable (delta = -72795865 ns)
Oct 15 18:56:59 alexandria-epia dhcdbd: Started up.
Oct 15 18:57:03 alexandria-epia kernel: [ 150.520234] RPC: Registered
udp transport module.
Oct 15 18:57:03 alexandria-epia kernel: [ 150.520257] RPC: Registered
tcp transport module.
Oct 15 18:57:04 alexandria-epia kernel: [ 150.989153] Installing knfsd
(copyright (C) 1996 okir@monad.swb.de).
Oct 15 18:57:04 alexandria-epia kernel: [ 81.206993] NFSD: Using
/var/lib/nfs/v4recovery as the NFSv4 state recovery directory
Oct 15 18:57:04 alexandria-epia kernel: [ 81.239059] NFSD: starting
90-second grace period
Oct 15 18:57:06 alexandria-epia kernel: [ 82.333813] [drm] Initialized
drm 1.1.0 20060810
Oct 15 18:57:06 alexandria-epia kernel: [ 82.353583] [drm] Initialized
via 2.11.1 20070202 on minor 0
Oct 15 18:57:06 alexandria-epia kernel: [ 82.403044] agpgart: Found an
AGP 2.0 compliant device at 0000:00:00.0.
Oct 15 18:57:06 alexandria-epia kernel: [ 82.403085] agpgart: Putting
AGP V2 device at 0000:00:00.0 into 4x mode
Oct 15 18:57:06 alexandria-epia kernel: [ 82.403153] agpgart: Putting
AGP V2 device at 0000:01:00.0 into 4x mode
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Lock
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Include
folders: ['/naspool_data/milan/Eigene-Dateien']
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Ignore
folders: []
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Last
snapshots: {}
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Compare with
old snapshot: 20091013-220848
Oct 15 18:57:13 alexandria-epia backintime (ramses): WARNING: Command
"rsync -aEAX -i --dry-run --chmod=Fa-w,D+w --whole-file --delete
--exclude="/naspool_data/milan/Back-in-Time"
--exclude="/home/ramses/.local/share/backintime"
--include="/naspool_data/milan/Eigene-Dateien/"
--include="/naspool_data/milan/" --include="/naspool_data/"
--exclude=".*" --exclude="*.backup*" --exclude="*~"
--include="/naspool_data/milan/Eigene-Dateien/**" --exclude="*" /
"/naspool_data/milan/Back-in-Time/backintime/20091013-220848/backup/""
returns 256
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Nothing
changed, no back needed
Oct 15 18:57:13 alexandria-epia backintime (ramses): WARNING: No new
snapshot (not needed or error)
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Remove
backups older than: 20041015-000000
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: [smart
remove] There is only one snapshots, so keep it
Oct 15 18:57:13 alexandria-epia backintime (ramses): INFO: Keep min free
disk space: 102400 Mb
Oct 15 18:57:15 alexandria-epia backintime (ramses): INFO: Unlock
Oct 15 18:58:02 alexandria-epia gnome-power-manager: (ramses)
Energieverwaltung is already running in this session.
Oct 15 19:16:56 alexandria-epia -- MARK --
Oct 15 19:36:56 alexandria-epia -- MARK --
Oct 15 19:56:56 alexandria-epia -- MARK --
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.469711] res
d0/00:80:00:75:41/00:00:00:00:00/e2 Emask 0x12 (ATA bus error)
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.778141] ata1: soft
resetting link
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.934009] ata1: SATA link
up 3.0 Gbps (SStatus 123 SControl 300)
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.963130] ata1.00:
configured for UDMA/133
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.963174] ata1: EH complete
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.982166] sd 0:0:0:0: [sda]
488397168 512-byte hardware sectors (250059 MB)
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.982237] sd 0:0:0:0: [sda]
Write Protect is off
Oct 15 20:05:24 alexandria-epia kernel: [ 4712.982332] sd 0:0:0:0: [sda]
Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Oct 15 20:16:56 alexandria-epia -- MARK --
Oct 15 20:20:46 alexandria-epia kernel: [ 5731.478618] res
40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Oct 15 20:20:51 alexandria-epia kernel: [ 5736.825857] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526446] ata1: device not
ready (errno=-16), forcing hardreset
Oct 15 20:20:56 alexandria-epia kernel: [ 5741.526472] ata1: hard
resetting link
Oct 15 20:21:02 alexandria-epia kernel: [ 5747.713897] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:06 alexandria-epia kernel: [ 5751.575082] ata1: hard
resetting link
Oct 15 20:21:12 alexandria-epia kernel: [ 5757.762534] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:16 alexandria-epia kernel: [ 5761.623715] ata1: hard
resetting link
Oct 15 20:21:22 alexandria-epia kernel: [ 5767.811162] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650099] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:21:51 alexandria-epia kernel: [ 5796.650114] ata1: hard
resetting link
Oct 15 20:21:56 alexandria-epia kernel: [ 5801.658417] ata1.00: disabled
Oct 15 20:21:56 alexandria-epia kernel: [ 5801.658536] ata1: hard
resetting link
Oct 15 20:22:02 alexandria-epia kernel: [ 5808.217578] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:22:06 alexandria-epia kernel: [ 5811.687078] ata1: hard
resetting link
Oct 15 20:22:12 alexandria-epia kernel: [ 5818.274258] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:22:16 alexandria-epia kernel: [ 5821.691766] ata1: hard
resetting link
Oct 15 20:22:23 alexandria-epia kernel: [ 5828.279061] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:22:51 alexandria-epia kernel: [ 5856.718163] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:22:51 alexandria-epia kernel: [ 5856.718178] ata1: hard
resetting link
Oct 15 20:22:56 alexandria-epia kernel: [ 5861.738615] ata1: hard
resetting link
Oct 15 20:23:03 alexandria-epia kernel: [ 5868.341658] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:23:06 alexandria-epia kernel: [ 5871.755193] ata1: hard
resetting link
Oct 15 20:23:13 alexandria-epia kernel: [ 5878.350348] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:23:16 alexandria-epia kernel: [ 5881.763886] ata1: hard
resetting link
Oct 15 20:23:23 alexandria-epia kernel: [ 5888.351051] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:23:51 alexandria-epia kernel: [ 5917.282365] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:23:51 alexandria-epia kernel: [ 5917.282380] ata1: hard
resetting link
Oct 15 20:23:56 alexandria-epia kernel: [ 5922.302823] ata1: hard
resetting link
Oct 15 20:24:03 alexandria-epia kernel: [ 5928.893884] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:24:06 alexandria-epia kernel: [ 5932.308846] ata1: hard
resetting link
Oct 15 20:24:13 alexandria-epia kernel: [ 5938.894607] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:24:16 alexandria-epia kernel: [ 5942.308193] ata1: hard
resetting link
Oct 15 20:24:23 alexandria-epia kernel: [ 5948.895326] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:24:51 alexandria-epia kernel: [ 5977.326697] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:24:51 alexandria-epia kernel: [ 5977.326712] ata1: hard
resetting link
Oct 15 20:24:56 alexandria-epia kernel: [ 5982.351151] ata1: hard
resetting link
Oct 15 20:25:03 alexandria-epia kernel: [ 5988.950311] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:25:06 alexandria-epia kernel: [ 5992.363869] ata1: hard
resetting link
Oct 15 20:25:13 alexandria-epia kernel: [ 5998.955224] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:25:16 alexandria-epia kernel: [ 6002.368707] ata1: hard
resetting link
Oct 15 20:25:23 alexandria-epia kernel: [ 6008.955955] ata1: port is
slow to respond, please be patient (Status 0xff)
Oct 15 20:25:51 alexandria-epia kernel: [ 6037.395626] ata1: limiting
SATA link speed to 1.5 Gbps
Oct 15 20:25:51 alexandria-epia kernel: [ 6037.395642] ata1: hard
resetting link
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416096] sd 0:0:0:0: [sda]
Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416119] sd 0:0:0:0: [sda]
Sense Key : Aborted Command [current] [descriptor]
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416144] Descriptor sense
data with sense descriptors (in hex):
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416157] 72 0b 00
00 00 00 00 0c 00 0a 80 00 00 00 00 00
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416194] 00 00 00 00
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416211] sd 0:0:0:0: [sda]
Add. Sense: No additional sense information
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416235] end_request: I/O
error, dev sda, sector 46898304
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.416279] ata1: EH complete
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.420602] ata1.00:
detaching (SCSI 0:0:0:0)
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.421613] sd 0:0:0:0: [sda]
Synchronizing SCSI cache
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.425374] sd 0:0:0:0: [sda]
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.425405] sd 0:0:0:0: [sda]
Stopping disk
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.425758] sd 0:0:0:0: [sda]
START_STOP FAILED
Oct 15 20:25:56 alexandria-epia kernel: [ 6042.425771] sd 0:0:0:0: [sda]
Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK
Oct 15 20:26:01 alexandria-epia kernel: [ 3229.201352] printk: 58056
messages suppressed.
Oct 15 20:26:06 alexandria-epia kernel: [ 3234.205044] printk: 55896
messages suppressed.
Oct 15 20:26:11 alexandria-epia kernel: [ 3239.203445] printk: 54639
messages suppressed.
Oct 15 20:26:16 alexandria-epia kernel: [ 3244.202383] printk: 57627
messages suppressed.
Oct 15 20:26:21 alexandria-epia kernel: [ 3249.197164] printk: 57827
messages suppressed.
Oct 15 20:26:26 alexandria-epia kernel: [ 3254.235350] printk: 56766
messages suppressed.
Oct 15 20:26:31 alexandria-epia kernel: [ 3259.206494] printk: 56007
messages suppressed.
Oct 15 20:26:36 alexandria-epia kernel: [ 3264.194019] printk: 57076
messages suppressed.
Oct 15 20:26:41 alexandria-epia kernel: [ 3269.217233] printk: 57609
messages suppressed.
Oct 15 20:26:46 alexandria-epia kernel: [ 3274.198062] printk: 57134
messages suppressed.
Oct 15 20:26:51 alexandria-epia kernel: [ 3279.190876] printk: 55536
messages suppressed.
Oct 15 20:26:56 alexandria-epia kernel: [ 3284.194655] printk: 56754
messages suppressed.
Oct 15 20:27:01 alexandria-epia kernel: [ 3289.188908] printk: 56462
messages suppressed.
Oct 15 20:27:06 alexandria-epia kernel: [ 3294.199876] printk: 58035
messages suppressed.
Oct 15 20:27:11 alexandria-epia kernel: [ 3299.191366] printk: 56992
messages suppressed.
Oct 15 20:27:16 alexandria-epia kernel: [ 3304.218411] printk: 56165
messages suppressed.
Oct 15 20:27:21 alexandria-epia kernel: [ 3309.192869] printk: 56700
messages suppressed.
Oct 15 20:27:26 alexandria-epia kernel: [ 3314.203828] printk: 56625
messages suppressed.
Oct 15 20:27:31 alexandria-epia kernel: [ 3319.182798] printk: 57850
messages suppressed.
Oct 15 20:27:36 alexandria-epia kernel: [ 3324.189708] printk: 56388
messages suppressed.
Oct 15 20:27:41 alexandria-epia kernel: [ 3329.180412] printk: 56685
messages suppressed.
Oct 15 20:27:46 alexandria-epia kernel: [ 3334.187466] printk: 57426
messages suppressed.
Oct 15 20:27:51 alexandria-epia kernel: [ 3339.178317] printk: 56907
messages suppressed.
Oct 15 20:27:56 alexandria-epia kernel: [ 3344.193380] printk: 57776
messages suppressed.
Oct 15 20:28:01 alexandria-epia kernel: [ 3349.188479] printk: 57536
messages suppressed.
Oct 15 20:28:06 alexandria-epia kernel: [ 3354.175306] printk: 55568
messages suppressed.
Oct 15 20:28:11 alexandria-epia kernel: [ 3359.175259] printk: 57028
messages suppressed.
Oct 15 20:28:16 alexandria-epia kernel: [ 3364.197592] printk: 57333
messages suppressed.
Oct 15 20:28:21 alexandria-epia kernel: [ 3369.184288] printk: 57658
messages suppressed.
Oct 15 20:28:26 alexandria-epia kernel: [ 3374.178743] printk: 56678
messages suppressed.
Oct 15 20:28:31 alexandria-epia kernel: [ 3379.174093] printk: 56841
messages suppressed.
Oct 15 20:28:36 alexandria-epia kernel: [ 3384.181644] printk: 56953
messages suppressed.
Oct 15 20:28:41 alexandria-epia kernel: [ 3389.167893] printk: 57125
messages suppressed.
Oct 15 20:28:46 alexandria-epia kernel: [ 3394.166908] printk: 50158
messages suppressed.
Oct 15 20:28:51 alexandria-epia kernel: [ 3399.166061] printk: 57506
messages suppressed.
Oct 15 20:28:56 alexandria-epia kernel: [ 3404.176976] printk: 57274
messages suppressed.
Oct 15 20:29:01 alexandria-epia kernel: [ 3409.179737] printk: 56445
messages suppressed.
Oct 15 20:29:06 alexandria-epia kernel: [ 3414.178775] printk: 57484
messages suppressed.
Oct 15 20:29:11 alexandria-epia kernel: [ 3419.161798] printk: 57346
messages suppressed.
Oct 15 20:29:16 alexandria-epia kernel: [ 3424.206680] printk: 57874
messages suppressed.
Oct 15 20:29:21 alexandria-epia kernel: [ 3429.168330] printk: 56015
messages suppressed.
Oct 15 20:29:26 alexandria-epia kernel: [ 3434.170657] printk: 56400
messages suppressed.
Oct 15 20:29:31 alexandria-epia kernel: [ 3439.164417] printk: 58399
messages suppressed.
Oct 15 20:29:36 alexandria-epia kernel: [ 3444.168687] printk: 56321
messages suppressed.
Oct 15 20:29:41 alexandria-epia kernel: [ 3449.155457] printk: 56930
messages suppressed.
Oct 15 20:29:46 alexandria-epia kernel: [ 3454.178635] printk: 55817
messages suppressed.
Oct 15 20:29:51 alexandria-epia kernel: [ 3459.153412] printk: 57252
messages suppressed.
Oct 15 20:29:56 alexandria-epia kernel: [ 3464.164405] printk: 58380
messages suppressed.
Oct 15 20:30:01 alexandria-epia kernel: [ 3469.151242] printk: 56203
messages suppressed.
Oct 15 20:30:06 alexandria-epia kernel: [ 3474.150214] printk: 56936
messages suppressed.
Oct 15 20:30:11 alexandria-epia kernel: [ 3479.157268] printk: 56362
messages suppressed.
Oct 15 20:30:16 alexandria-epia kernel: [ 3484.148117] printk: 56088
messages suppressed.
Oct 15 20:30:21 alexandria-epia kernel: [ 3489.147110] printk: 57905
messages suppressed.
Oct 15 20:30:26 alexandria-epia kernel: [ 3494.170161] printk: 56089
messages suppressed.
Oct 15 20:30:31 alexandria-epia kernel: [ 3499.148540] printk: 57544
messages suppressed.
Oct 15 20:30:36 alexandria-epia kernel: [ 3504.156076] printk: 56149
messages suppressed.
Oct 15 20:30:41 alexandria-epia kernel: [ 3509.144470] printk: 58096
messages suppressed.
Oct 15 20:30:46 alexandria-epia kernel: [ 3514.141886] printk: 57648
messages suppressed.
Oct 15 20:30:51 alexandria-epia kernel: [ 3519.167677] printk: 56172
messages suppressed.
Oct 15 20:30:56 alexandria-epia kernel: [ 3524.149442] printk: 56296
messages suppressed.
Oct 15 20:31:01 alexandria-epia kernel: [ 3529.173825] printk: 56543
messages suppressed.
Oct 15 20:31:06 alexandria-epia kernel: [ 3534.142046] printk: 57400
messages suppressed.
Oct 15 20:31:11 alexandria-epia kernel: [ 3539.144648] printk: 57764
messages suppressed.
Oct 15 20:31:16 alexandria-epia kernel: [ 3544.135834] printk: 55831
messages suppressed.
Oct 15 20:31:21 alexandria-epia kernel: [ 3549.138827] printk: 56413
messages suppressed.
Oct 15 20:31:26 alexandria-epia kernel: [ 3554.137979] printk: 55730
messages suppressed.
Oct 15 20:31:31 alexandria-epia kernel: [ 3559.132546] printk: 57203
messages suppressed.
Oct 15 20:31:36 alexandria-epia kernel: [ 3564.132314] printk: 55991
messages suppressed.
Oct 15 20:31:41 alexandria-epia kernel: [ 3569.159913] printk: 57235
messages suppressed.
Oct 15 20:31:46 alexandria-epia kernel: [ 3574.141727] printk: 56423
messages suppressed.
Oct 15 20:31:51 alexandria-epia kernel: [ 3579.136482] printk: 57275
messages suppressed.
Oct 15 20:31:56 alexandria-epia kernel: [ 3584.138632] printk: 57901
messages suppressed.
Oct 15 20:32:01 alexandria-epia kernel: [ 3589.126362] printk: 55934
messages suppressed.
Oct 15 20:32:06 alexandria-epia kernel: [ 3594.154458] printk: 55794
messages suppressed.
Oct 15 20:32:11 alexandria-epia kernel: [ 3599.141288] printk: 58209
messages suppressed.
Oct 15 20:32:16 alexandria-epia kernel: [ 3604.123272] printk: 57454
messages suppressed.
Oct 15 20:32:21 alexandria-epia kernel: [ 3609.128975] printk: 57315
messages suppressed.
Oct 15 20:32:26 alexandria-epia kernel: [ 3614.121455] printk: 55829
messages suppressed.
Oct 15 20:32:31 alexandria-epia kernel: [ 3619.128343] printk: 57432
messages suppressed.
Oct 15 20:32:36 alexandria-epia kernel: [ 3624.119131] printk: 56418
messages suppressed.
Oct 15 20:32:41 alexandria-epia kernel: [ 3629.120875] printk: 56254
messages suppressed.
Oct 15 20:32:46 alexandria-epia kernel: [ 3634.131739] printk: 56200
messages suppressed.
Oct 15 20:32:51 alexandria-epia kernel: [ 3639.116094] printk: 57371
messages suppressed.
Oct 15 20:32:56 alexandria-epia kernel: [ 3644.119225] printk: 55993
messages suppressed.
Oct 15 20:33:01 alexandria-epia kernel: [ 3649.113953] printk: 57137
messages suppressed.
Oct 15 20:33:06 alexandria-epia kernel: [ 3654.117411] printk: 55590
messages suppressed.
Oct 15 20:33:11 alexandria-epia kernel: [ 3659.127350] printk: 56027
messages suppressed.
Oct 15 20:33:16 alexandria-epia kernel: [ 3664.125399] printk: 56090
messages suppressed.
Oct 15 20:33:21 alexandria-epia kernel: [ 3669.120432] printk: 56515
messages suppressed.
Oct 15 20:33:26 alexandria-epia kernel: [ 3674.139650] printk: 58085
messages suppressed.
Oct 15 20:33:31 alexandria-epia kernel: [ 3679.115942] printk: 56786
messages suppressed.
Oct 15 20:33:36 alexandria-epia kernel: [ 3684.113709] printk: 55181
messages suppressed.
Oct 15 20:33:41 alexandria-epia kernel: [ 3689.106004] printk: 57292
messages suppressed.
Oct 15 20:33:46 alexandria-epia kernel: [ 3694.118522] printk: 50620
messages suppressed.
Oct 15 20:33:51 alexandria-epia kernel: [ 3699.104308] printk: 57015
messages suppressed.
Oct 15 20:33:56 alexandria-epia kernel: [ 3704.103347] printk: 56276
messages suppressed.
Oct 15 20:34:01 alexandria-epia kernel: [ 3709.108856] printk: 55820
messages suppressed.
Oct 15 20:34:06 alexandria-epia kernel: [ 3714.113963] printk: 57194
messages suppressed.
Oct 15 20:34:11 alexandria-epia kernel: [ 3719.100690] printk: 56656
messages suppressed.
Oct 15 20:34:16 alexandria-epia kernel: [ 3724.104087] printk: 56871
messages suppressed.
Oct 15 20:34:21 alexandria-epia kernel: [ 3729.099001] printk: 57775
messages suppressed.
Oct 15 20:34:26 alexandria-epia kernel: [ 3734.134743] printk: 56592
messages suppressed.
Oct 15 20:34:31 alexandria-epia kernel: [ 3739.109402] printk: 57752
messages suppressed.
Oct 15 20:34:36 alexandria-epia kernel: [ 3744.096271] printk: 55149
messages suppressed.
Oct 15 20:34:41 alexandria-epia kernel: [ 3749.102733] printk: 55328
messages suppressed.
Oct 15 20:34:46 alexandria-epia kernel: [ 3754.106507] printk: 57443
messages suppressed.
Oct 15 20:34:51 alexandria-epia kernel: [ 3759.103564] printk: 57148
messages suppressed.
Oct 15 20:34:56 alexandria-epia kernel: [ 3764.096738] printk: 56921
messages suppressed.
Oct 15 20:35:01 alexandria-epia kernel: [ 3769.129935] printk: 55964
messages suppressed.
Oct 15 20:35:06 alexandria-epia kernel: [ 3774.095176] printk: 56760
messages suppressed.
Oct 15 20:35:11 alexandria-epia kernel: [ 3779.101244] printk: 57063
messages suppressed.
Oct 15 20:35:16 alexandria-epia kernel: [ 3784.101580] printk: 58139
messages suppressed.
Oct 15 20:35:21 alexandria-epia kernel: [ 3789.088123] printk: 57406
messages suppressed.
Oct 15 20:35:26 alexandria-epia kernel: [ 3794.087270] printk: 56617
messages suppressed.
Oct 15 20:35:31 alexandria-epia kernel: [ 3799.106471] printk: 56304
messages suppressed.
Oct 15 20:35:36 alexandria-epia kernel: [ 3804.087945] printk: 55649
messages suppressed.
Oct 15 20:35:41 alexandria-epia kernel: [ 3809.112015] printk: 57640
messages suppressed.
Oct 15 20:35:46 alexandria-epia kernel: [ 3814.083888] printk: 56030
messages suppressed.
Oct 15 20:35:51 alexandria-epia kernel: [ 3819.082716] printk: 55645
messages suppressed.
Oct 15 20:35:56 alexandria-epia kernel: [ 3824.092227] printk: 57767
messages suppressed.
Oct 15 20:36:01 alexandria-epia kernel: [ 3829.084996] printk: 57403
messages suppressed.
Oct 15 20:36:06 alexandria-epia kernel: [ 3834.085510] printk: 55639
messages suppressed.
Oct 15 20:36:11 alexandria-epia kernel: [ 3839.086933] printk: 55618
messages suppressed.
Oct 15 20:36:16 alexandria-epia kernel: [ 3844.089274] printk: 56590
messages suppressed.
Oct 15 20:36:21 alexandria-epia kernel: [ 3849.079477] printk: 57262
messages suppressed.
Oct 15 20:36:26 alexandria-epia kernel: [ 3854.080911] printk: 57807
messages suppressed.
Oct 15 20:36:31 alexandria-epia kernel: [ 3859.087688] printk: 55651
messages suppressed.
Oct 15 20:36:36 alexandria-epia kernel: [ 3864.074571] printk: 57099
messages suppressed.
Oct 15 20:36:41 alexandria-epia kernel: [ 3869.084921] printk: 57310
messages suppressed.
Oct 15 20:36:46 alexandria-epia kernel: [ 3874.076999] printk: 56639
messages suppressed.
Oct 15 20:36:51 alexandria-epia kernel: [ 3879.071856] printk: 56682
messages suppressed.
Oct 15 20:36:56 alexandria-epia kernel: [ 3884.078078] printk: 55770
messages suppressed.
Oct 15 20:37:01 alexandria-epia kernel: [ 3889.082255] printk: 56984
messages suppressed.
Oct 15 20:37:06 alexandria-epia kernel: [ 3894.073569] printk: 56552
messages suppressed.
Oct 15 20:37:11 alexandria-epia kernel: [ 3899.072302] printk: 57028
messages suppressed.
Oct 15 20:37:16 alexandria-epia kernel: [ 3904.070505] printk: 54904
messages suppressed.
Oct 15 20:37:21 alexandria-epia kernel: [ 3909.078795] printk: 56373
messages suppressed.
Oct 15 20:37:26 alexandria-epia kernel: [ 3914.065504] printk: 57068
messages suppressed.
Oct 15 20:37:31 alexandria-epia kernel: [ 3919.068760] printk: 55467
messages suppressed.
Oct 15 20:37:36 alexandria-epia kernel: [ 3924.063678] printk: 57371
messages suppressed.
Oct 15 20:37:41 alexandria-epia kernel: [ 3929.110562] printk: 55989
messages suppressed.
Oct 15 20:37:46 alexandria-epia kernel: [ 3934.114147] printk: 56489
messages suppressed.
Oct 15 20:37:51 alexandria-epia kernel: [ 3939.060927] printk: 56740
messages suppressed.
Oct 15 20:37:56 alexandria-epia kernel: [ 3944.064249] printk: 56164
messages suppressed.
Oct 15 20:38:01 alexandria-epia kernel: [ 3949.065852] printk: 56785
messages suppressed.
Oct 15 20:38:06 alexandria-epia kernel: [ 3954.058326] printk: 56566
messages suppressed.
Oct 15 20:38:11 alexandria-epia kernel: [ 3959.057315] printk: 57861
messages suppressed.
Oct 15 20:38:16 alexandria-epia kernel: [ 3964.056409] printk: 56342
messages suppressed.
Oct 15 20:38:21 alexandria-epia kernel: [ 3969.056899] printk: 56367
messages suppressed.
Oct 15 20:38:26 alexandria-epia kernel: [ 3974.070777] printk: 55905
messages suppressed.
Oct 15 20:38:31 alexandria-epia kernel: [ 3979.065704] printk: 57014
messages suppressed.
Oct 15 20:38:36 alexandria-epia kernel: [ 3984.052743] printk: 56026
messages suppressed.
Oct 15 20:38:41 alexandria-epia kernel: [ 3989.058524] printk: 56023
messages suppressed.
Oct 15 20:38:46 alexandria-epia kernel: [ 3994.051009] printk: 50794
messages suppressed.
Oct 15 20:38:51 alexandria-epia kernel: [ 3999.060250] printk: 56603
messages suppressed.
Oct 15 20:38:56 alexandria-epia kernel: [ 4004.053786] printk: 55790
messages suppressed.
Oct 15 20:39:01 alexandria-epia kernel: [ 4009.053042] printk: 56364
messages suppressed.
Oct 15 20:39:06 alexandria-epia kernel: [ 4014.051341] printk: 55206
messages suppressed.
Oct 15 20:39:11 alexandria-epia kernel: [ 4019.049663] printk: 57709
messages suppressed.
Oct 15 20:39:16 alexandria-epia kernel: [ 4024.046964] printk: 57009
messages suppressed.
Oct 15 20:39:21 alexandria-epia kernel: [ 4029.048647] printk: 55038
messages suppressed.
Oct 15 20:39:26 alexandria-epia kernel: [ 4034.043743] printk: 57039
messages suppressed.
Oct 15 20:39:31 alexandria-epia kernel: [ 4039.050941] printk: 56591
messages suppressed.
Oct 15 20:39:36 alexandria-epia kernel: [ 4044.045792] printk: 57193
messages suppressed.
Oct 15 20:39:41 alexandria-epia kernel: [ 4049.044996] printk: 55319
messages suppressed.
Oct 15 20:39:46 alexandria-epia kernel: [ 4054.048075] printk: 56450
messages suppressed.
Oct 15 20:39:51 alexandria-epia kernel: [ 4059.038936] printk: 56516
messages suppressed.
Oct 15 20:39:56 alexandria-epia kernel: [ 4064.038017] printk: 57658
messages suppressed.
Oct 15 20:40:01 alexandria-epia kernel: [ 4069.037402] printk: 55407
messages suppressed.
Oct 15 20:40:06 alexandria-epia kernel: [ 4074.048319] printk: 57221
messages suppressed.
Oct 15 20:40:11 alexandria-epia kernel: [ 4079.035253] printk: 55405
messages suppressed.
Oct 15 20:40:16 alexandria-epia kernel: [ 4084.045362] printk: 56682
messages suppressed.
Oct 15 20:40:21 alexandria-epia kernel: [ 4089.047445] printk: 57388
messages suppressed.
Oct 15 20:40:26 alexandria-epia kernel: [ 4094.041791] printk: 57056
messages suppressed.
Oct 15 20:40:31 alexandria-epia kernel: [ 4099.043778] printk: 57487
messages suppressed.
Oct 15 20:40:36 alexandria-epia kernel: [ 4104.051574] printk: 55761
messages suppressed.
Oct 15 20:40:41 alexandria-epia kernel: [ 4109.029957] printk: 55892
messages suppressed.
Oct 15 20:40:46 alexandria-epia kernel: [ 4114.028836] printk: 57282
messages suppressed.
Oct 15 20:40:51 alexandria-epia kernel: [ 4119.031780] printk: 55296
messages suppressed.
Oct 15 20:40:56 alexandria-epia kernel: [ 4124.039228] printk: 57602
messages suppressed.
Oct 15 20:41:01 alexandria-epia kernel: [ 4129.026073] printk: 56592
messages suppressed.
Oct 15 20:41:06 alexandria-epia kernel: [ 4134.037246] printk: 56466
messages suppressed.
Oct 15 20:41:11 alexandria-epia kernel: [ 4139.056192] printk: 55415
messages suppressed.
Oct 15 20:41:16 alexandria-epia kernel: [ 4144.027597] printk: 55960
messages suppressed.
Oct 15 20:41:21 alexandria-epia kernel: [ 4149.029408] printk: 58188
messages suppressed.
Oct 15 20:41:26 alexandria-epia kernel: [ 4154.025582] printk: 55562
messages suppressed.
Oct 15 20:41:31 alexandria-epia kernel: [ 4159.047482] printk: 55822
messages suppressed.
Oct 15 20:41:36 alexandria-epia kernel: [ 4164.031637] printk: 55222
messages suppressed.
Oct 15 20:41:41 alexandria-epia kernel: [ 4169.039863] printk: 56598
messages suppressed.
Oct 15 20:41:46 alexandria-epia kernel: [ 4174.025766] printk: 57571
messages suppressed.
Oct 15 20:41:51 alexandria-epia kernel: [ 4179.035945] printk: 56831
messages suppressed.
Oct 15 20:41:56 alexandria-epia kernel: [ 4184.015799] printk: 55510
messages suppressed.
Oct 15 20:42:01 alexandria-epia kernel: [ 4189.038968] printk: 56848
messages suppressed.
Oct 15 20:42:06 alexandria-epia kernel: [ 4194.033889] printk: 56083
messages suppressed.
Oct 15 20:42:11 alexandria-epia kernel: [ 4199.030214] printk: 55857
messages suppressed.
Oct 15 20:42:16 alexandria-epia kernel: [ 4204.012345] printk: 54387
messages suppressed.
Oct 15 20:42:21 alexandria-epia kernel: [ 4209.042634] printk: 56998
messages suppressed.
Oct 15 20:42:26 alexandria-epia kernel: [ 4214.010718] printk: 55918
messages suppressed.
Oct 15 20:42:31 alexandria-epia kernel: [ 4219.011222] printk: 56173
messages suppressed.
Oct 15 20:42:36 alexandria-epia kernel: [ 4224.009054] printk: 57062
messages suppressed.
Oct 15 20:42:41 alexandria-epia kernel: [ 4229.008196] printk: 55767
messages suppressed.
Oct 15 20:42:46 alexandria-epia kernel: [ 4234.012970] printk: 57561
messages suppressed.
Oct 15 20:42:51 alexandria-epia kernel: [ 4239.006625] printk: 56029
messages suppressed.
Oct 15 20:42:56 alexandria-epia kernel: [ 4244.005777] printk: 55082
messages suppressed.
Oct 15 20:43:01 alexandria-epia kernel: [ 4249.017471] printk: 57666
messages suppressed.
Oct 15 20:43:06 alexandria-epia kernel: [ 4254.004012] printk: 55598
messages suppressed.
Oct 15 20:43:11 alexandria-epia kernel: [ 4259.003190] printk: 56541
messages suppressed.
Oct 15 20:43:16 alexandria-epia kernel: [ 4264.002609] printk: 55624
messages suppressed.
Oct 15 20:43:21 alexandria-epia kernel: [ 4269.001510] printk: 57052
messages suppressed.
Oct 15 20:43:26 alexandria-epia kernel: [ 4274.002967] printk: 57143
messages suppressed.
Oct 15 20:43:31 alexandria-epia kernel: [ 4279.015967] printk: 55772
messages suppressed.
Oct 15 20:43:36 alexandria-epia kernel: [ 4284.007266] printk: 56014
messages suppressed.
Oct 15 20:43:41 alexandria-epia kernel: [ 4289.006299] printk: 56721
messages suppressed.
Oct 15 20:43:46 alexandria-epia kernel: [ 4293.997336] printk: 50669
messages suppressed.
Oct 15 20:43:51 alexandria-epia kernel: [ 4299.004758] printk: 56115
messages suppressed.
Oct 15 20:43:56 alexandria-epia kernel: [ 4304.007931] printk: 54892
messages suppressed.
Oct 15 20:44:01 alexandria-epia kernel: [ 4309.023007] printk: 55947
messages suppressed.
Oct 15 20:44:06 alexandria-epia kernel: [ 4313.998239] printk: 56479
messages suppressed.
Oct 15 20:44:11 alexandria-epia kernel: [ 4319.005178] printk: 57125
messages suppressed.
Oct 15 20:44:16 alexandria-epia kernel: [ 4323.992259] printk: 55761
messages suppressed.
Oct 15 20:44:21 alexandria-epia kernel: [ 4328.995545] printk: 55390
messages suppressed.
Oct 15 20:44:26 alexandria-epia kernel: [ 4333.990741] printk: 56824
messages suppressed.
Oct 15 20:44:31 alexandria-epia kernel: [ 4338.993775] printk: 55206
messages suppressed.
Oct 15 20:44:36 alexandria-epia kernel: [ 4343.988913] printk: 54788
messages suppressed.
Oct 15 20:44:41 alexandria-epia kernel: [ 4348.993912] printk: 56652
messages suppressed.
Oct 15 20:44:46 alexandria-epia kernel: [ 4354.009857] printk: 56075
messages suppressed.
Oct 15 20:44:51 alexandria-epia kernel: [ 4358.986623] printk: 57317
messages suppressed.
Oct 15 20:44:56 alexandria-epia kernel: [ 4363.989925] printk: 55191
messages suppressed.
Oct 15 20:45:01 alexandria-epia kernel: [ 4368.984634] printk: 56512
messages suppressed.
Oct 15 20:45:06 alexandria-epia kernel: [ 4373.983769] printk: 56452
messages suppressed.
Oct 15 20:45:11 alexandria-epia kernel: [ 4379.039029] printk: 56700
messages suppressed.
Oct 15 20:45:16 alexandria-epia kernel: [ 4383.982192] printk: 54682
messages suppressed.
Oct 15 20:45:21 alexandria-epia kernel: [ 4388.981220] printk: 56460
messages suppressed.
Oct 15 20:45:26 alexandria-epia kernel: [ 4393.993681] printk: 57604
messages suppressed.
Oct 15 20:45:31 alexandria-epia kernel: [ 4398.982440] printk: 56579
messages suppressed.
Oct 15 20:45:36 alexandria-epia kernel: [ 4403.981684] printk: 55791
messages suppressed.
Oct 15 20:45:41 alexandria-epia kernel: [ 4409.006216] printk: 55370
messages suppressed.
Oct 15 20:45:46 alexandria-epia kernel: [ 4413.989323] printk: 57072
messages suppressed.
Oct 15 20:45:51 alexandria-epia kernel: [ 4418.976420] printk: 56575
messages suppressed.
Oct 15 20:45:56 alexandria-epia kernel: [ 4423.996021] printk: 55755
messages suppressed.
Oct 15 20:46:01 alexandria-epia kernel: [ 4428.986587] printk: 56669
messages suppressed.
Oct 15 20:46:06 alexandria-epia kernel: [ 4433.977593] printk: 56902
messages suppressed.
Oct 15 20:46:11 alexandria-epia kernel: [ 4438.984810] printk: 56802
messages suppressed.
Oct 15 20:46:16 alexandria-epia kernel: [ 4443.971766] printk: 55044
messages suppressed.
Oct 15 20:46:21 alexandria-epia kernel: [ 4448.970927] printk: 56495
messages suppressed.
Oct 15 20:46:26 alexandria-epia kernel: [ 4453.970059] printk: 56142
messages suppressed.
Oct 15 20:46:31 alexandria-epia kernel: [ 4458.969222] printk: 56419
messages suppressed.
Oct 15 20:46:36 alexandria-epia kernel: [ 4463.992083] printk: 54820
messages suppressed.
Oct 15 20:46:41 alexandria-epia kernel: [ 4468.968807] printk: 56888
messages suppressed.
Oct 15 20:46:46 alexandria-epia kernel: [ 4473.978775] printk: 57488
messages suppressed.
Oct 15 20:46:51 alexandria-epia kernel: [ 4478.990478] printk: 55535
messages suppressed.
Oct 15 20:46:56 alexandria-epia kernel: [ 4483.973127] printk: 56481
messages suppressed.
Oct 15 20:47:01 alexandria-epia kernel: [ 4488.972412] printk: 55654
messages suppressed.
Oct 15 20:47:06 alexandria-epia kernel: [ 4493.963145] printk: 57109
messages suppressed.
Oct 15 20:47:11 alexandria-epia kernel: [ 4498.986473] printk: 56653
messages suppressed.
Oct 15 20:47:16 alexandria-epia kernel: [ 4503.968145] printk: 54844
messages suppressed.
Oct 15 20:47:21 alexandria-epia kernel: [ 4508.972690] printk: 57044
messages suppressed.
Oct 15 20:47:26 alexandria-epia kernel: [ 4513.982400] printk: 56676
messages suppressed.
Oct 15 20:47:31 alexandria-epia kernel: [ 4518.958815] printk: 55031
messages suppressed.
Oct 15 20:47:36 alexandria-epia kernel: [ 4523.969735] printk: 52997
messages suppressed.
Oct 15 20:47:41 alexandria-epia kernel: [ 4528.957295] printk: 55755
messages suppressed.
Oct 15 20:47:46 alexandria-epia kernel: [ 4533.956730] printk: 56769
messages suppressed.
Oct 15 20:47:51 alexandria-epia kernel: [ 4538.955784] printk: 54536
messages suppressed.
Oct 15 20:47:56 alexandria-epia kernel: [ 4543.961813] printk: 55323
messages suppressed.
Oct 15 20:48:25 alexandria-epia kernel: [ 4564.381020] nfsd: last server
has exited
Oct 15 20:48:25 alexandria-epia kernel: [ 4564.381033] nfsd: unexporting
all filesystems
Oct 15 20:48:26 alexandria-epia exiting on signal 15
Oct 19 18:50:18 alexandria-epia syslogd 1.5.0#1ubuntu1: restart.
It's a VIA Epia M-10000 board with a Promise TX2 Plus SATA300
Controller. 1st IDE-Onboard-Channel is a 30 GB IDE harddisk with the
xubunt 8.04 and 2 GB Swap, 2nd IDE-Onboard-Channel is a LG DVD-RAM.
Promise 1st SATA-Channel is a 250GB harddisk (2,5"), Promise 2nd
SATA-Channel is a 250GB harddisk (2,5"). All disks with ext3-filesystem.
No raid, but automatic syncs between the two SATA-disks.
> FWIW, the 2.6.32-rc kernel has updates for the controller reset operations
> which may help get stubborn disks back on line. That patch is available
> for 2.6.28 to 2.6.31 kernels in the patch repository you mention below.
> Libata has a generic libata.force= parameter which can be used to tweak
> various settings, including 1.5Gbps vs 3Gbps. I haven't used it myself,
> but see Documentation/kernel-parameters.txt for details.
Thank you for this possibility. I discovered, that libata.force isn't
mentioned in Documentation/kernel-parameters.txt for 2.6.24. So I will
upgrade my system to xubuntu 9.04 (2.6.28) or xubuntu 9.10 (2.6.31) to
check libata.force and the newer patches.
Best regards, Milan
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work
2009-10-28 14:54 ` Milan Burgdorf
@ 2009-11-01 15:44 ` Milan Burgdorf
0 siblings, 0 replies; 4+ messages in thread
From: Milan Burgdorf @ 2009-11-01 15:44 UTC (permalink / raw)
To: linux-ide
>> the 2.6.32-rc kernel has updates for the controller reset operations
>> which may help get stubborn disks back on line. That patch is available
>> for 2.6.28 to 2.6.31 kernels in the patch repository you mention below.
>
>> Libata has a generic libata.force= parameter which can be used to tweak
>> various settings, including 1.5Gbps vs 3Gbps. I haven't used it myself,
>> but see Documentation/kernel-parameters.txt for details.
>
Now I'm using Xubuntu 9.10 with Kernel 2.6.31. "libata.force=1.5Gbps"
parameter at kernel starting works very fine up to now.
During the next days I'll patch the sata_promise module with your
additions to test the "other" way.
Thank you very much! My problem is solved!!!
Milan
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2009-11-01 15:44 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-10-23 12:31 Request to 2.6.24/patch-sata_promise-limit-sataii-to-1.5Gbps-2.6.24 because it doesn't work Milan Burgdorf
2009-10-23 13:19 ` Mikael Pettersson
2009-10-28 14:54 ` Milan Burgdorf
2009-11-01 15:44 ` Milan Burgdorf
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox