[PATCH AUTOSEL 5.4 14/52] iio: st_accel: Fix unused variable warning

[PATCH AUTOSEL 5.4 14/52] iio: st_accel: Fix unused variable warning

[Sasha Levin]

From: YueHaibing <yuehaibing@huawei.com>

[ Upstream commit 0163c1c521ff8b09cd8ca395003cc00178161d77 ]

drivers/iio/accel/st_accel_core.c:1005:44: warning:
 mount_matrix_ext_info defined but not used [-Wunused-const-variable=]

Using stub helper while CONFIG_ACPI is disabled to fix it.

Suggested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/iio/accel/st_accel_core.c | 8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/accel/st_accel_core.c b/drivers/iio/accel/st_accel_core.c
index 2e37f8a6d8cfc..be661396095ce 100644
--- a/drivers/iio/accel/st_accel_core.c
+++ b/drivers/iio/accel/st_accel_core.c
@@ -993,6 +993,7 @@ static const struct iio_trigger_ops st_accel_trigger_ops = {
 #define ST_ACCEL_TRIGGER_OPS NULL
 #endif
 
+#ifdef CONFIG_ACPI
 static const struct iio_mount_matrix *
 get_mount_matrix(const struct iio_dev *indio_dev,
 		 const struct iio_chan_spec *chan)
@@ -1013,7 +1014,6 @@ static const struct iio_chan_spec_ext_info mount_matrix_ext_info[] = {
 static int apply_acpi_orientation(struct iio_dev *indio_dev,
 				  struct iio_chan_spec *channels)
 {
-#ifdef CONFIG_ACPI
 	struct st_sensor_data *adata = iio_priv(indio_dev);
 	struct acpi_buffer buffer = {ACPI_ALLOCATE_BUFFER, NULL};
 	struct acpi_device *adev;
@@ -1141,10 +1141,14 @@ static int apply_acpi_orientation(struct iio_dev *indio_dev,
 out:
 	kfree(buffer.pointer);
 	return ret;
+}
 #else /* !CONFIG_ACPI */
+static int apply_acpi_orientation(struct iio_dev *indio_dev,
+				  struct iio_chan_spec *channels)
+{
 	return 0;
-#endif
 }
+#endif
 
 /*
  * st_accel_get_settings() - get sensor settings from device name
-- 
2.20.1

[PATCH AUTOSEL 5.4 15/52] iio: adc: max9611: Fix too short conversion time delay

[Sasha Levin]

From: Geert Uytterhoeven <geert+renesas@glider.be>

[ Upstream commit 9fd229c478fbf77c41c8528aa757ef14210365f6 ]

As of commit b9ddd5091160793e ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:

    max9611 4-007f: Invalid value received from ADC 0x8000: aborting
    max9611: probe of 4-007f failed with error -5

The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.

According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided.  Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).

However, the driver assumes a 1 ms conversion time.  Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned.  After boot, this is
the temperature POR (power-on reset) value, causing the failure above.

Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.

Note that this issue has always been present, but it was exposed by the
aformentioned commit.

Fixes: 69780a3bbc0b1e7e ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/iio/adc/max9611.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

diff --git a/drivers/iio/adc/max9611.c b/drivers/iio/adc/max9611.c
index da073d72f649f..e480529b3f049 100644
--- a/drivers/iio/adc/max9611.c
+++ b/drivers/iio/adc/max9611.c
@@ -89,6 +89,12 @@
 #define MAX9611_TEMP_SCALE_NUM		1000000
 #define MAX9611_TEMP_SCALE_DIV		2083
 
+/*
+ * Conversion time is 2 ms (typically) at Ta=25 degreeC
+ * No maximum value is known, so play it safe.
+ */
+#define MAX9611_CONV_TIME_US_RANGE	3000, 3300
+
 struct max9611_dev {
 	struct device *dev;
 	struct i2c_client *i2c_client;
@@ -236,11 +242,9 @@ static int max9611_read_single(struct max9611_dev *max9611,
 		return ret;
 	}
 
-	/*
-	 * need a delay here to make register configuration
-	 * stabilize. 1 msec at least, from empirical testing.
-	 */
-	usleep_range(1000, 2000);
+	/* need a delay here to make register configuration stabilize. */
+
+	usleep_range(MAX9611_CONV_TIME_US_RANGE);
 
 	ret = i2c_smbus_read_word_swapped(max9611->i2c_client, reg_addr);
 	if (ret < 0) {
@@ -507,7 +511,7 @@ static int max9611_init(struct max9611_dev *max9611)
 			MAX9611_REG_CTRL2, 0);
 		return ret;
 	}
-	usleep_range(1000, 2000);
+	usleep_range(MAX9611_CONV_TIME_US_RANGE);
 
 	return 0;
 }
-- 
2.20.1