Re: [PATCH v2 15/19] iio: chemical: bme680: Modify startup procedure

[Jonathan Cameron <jic23@kernel.org>]

On Thu,  6 Jun 2024 23:23:09 +0200
Vasileios Amoiridis <vassilisamir@gmail.com> wrote:

> Modify the startup procedure to reflect the procedure of
> the Bosch BME68x Sensor API. The initial readings and
> configuration of the sensor need to happen in the
> following order:
> 
> 1) Read calibration data [1,2]
> 2) Chip general configuration [3]
> 3) Gas configuration [4]
> 
> After the chip configuration it is necessary to ensure that
> the sensor is in sleeping mode, in order to apply the gas
> configuration settings [5].
> 

Trivial but oddly short line wrapping. Target 75ish chars for commit messages

> Also, after the soft reset, it is advised to wait for 5ms [6].
> 
> [1]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L162
> [2]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L44
> [3]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L53
> [4]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/examples/forced_mode/forced_mode.c#L60
> [5]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L640
> [6]: https://github.com/boschsensortec/BME68x_SensorAPI/blob/v4.4.8/bme68x.c#L294
Either make these Link tags or add a blank line here.

I'd prefer link tags with # [1] etc after them for the cross references.

> Signed-off-by: Vasileios Amoiridis <vassilisamir@gmail.com>
> ---
>  drivers/iio/chemical/bme680.h      |  2 ++
>  drivers/iio/chemical/bme680_core.c | 21 ++++++++++++++-------
>  2 files changed, 16 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/iio/chemical/bme680.h b/drivers/iio/chemical/bme680.h
> index 7d0ff294725a..b2c547ac8d34 100644
> --- a/drivers/iio/chemical/bme680.h
> +++ b/drivers/iio/chemical/bme680.h
> @@ -63,6 +63,8 @@
>  
>  #define BME680_MEAS_TRIM_MASK			GENMASK(24, 4)
>  
> +#define BME680_STARTUP_TIME_US			5000
> +
>  /* Calibration Parameters */
>  #define BME680_T2_LSB_REG	0x8A
>  #define BME680_H2_MSB_REG	0xE1
> diff --git a/drivers/iio/chemical/bme680_core.c b/drivers/iio/chemical/bme680_core.c
> index 25d128e1ddcf..e354eaa34d59 100644
> --- a/drivers/iio/chemical/bme680_core.c
> +++ b/drivers/iio/chemical/bme680_core.c
> @@ -531,6 +531,11 @@ static int bme680_gas_config(struct bme680_data *data)
>  	int ret;
>  	u8 heatr_res, heatr_dur;
>  
> +	/* Go to sleep */
> +	ret = bme680_set_mode(data, false);
> +	if (ret < 0)
> +		return ret;
> +
>  	heatr_res = bme680_calc_heater_res(data, data->heater_temp);
>  
>  	/* set target heater temperature */
> @@ -866,6 +871,8 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap,
>  		return ret;
>  	}
>  
> +	usleep_range(BME680_STARTUP_TIME_US, BME680_STARTUP_TIME_US + 1000);
> +
>  	ret = regmap_read(regmap, BME680_REG_CHIP_ID, &data->check);
>  	if (ret < 0) {
>  		dev_err(dev, "Error reading chip ID\n");
> @@ -878,22 +885,22 @@ int bme680_core_probe(struct device *dev, struct regmap *regmap,
>  		return -ENODEV;
>  	}
>  
> -	ret = bme680_chip_config(data);
> +	ret = bme680_read_calib(data, &data->bme680);
>  	if (ret < 0) {
> -		dev_err(dev, "failed to set chip_config data\n");
> +		dev_err(dev,
> +			"failed to read calibration coefficients at probe\n");
>  		return ret;
>  	}
>  
> -	ret = bme680_gas_config(data);
> +	ret = bme680_chip_config(data);
>  	if (ret < 0) {
> -		dev_err(dev, "failed to set gas config data\n");
> +		dev_err(dev, "failed to set chip_config data\n");
>  		return ret;
>  	}
>  
> -	ret = bme680_read_calib(data, &data->bme680);
> +	ret = bme680_gas_config(data);
>  	if (ret < 0) {
> -		dev_err(dev,
> -			"failed to read calibration coefficients at probe\n");
> +		dev_err(dev, "failed to set gas config data\n");
>  		return ret;
>  	}
>