[PATCH v4 00/10] Input: cap11xx - Add support for CAP1114

[PATCH v4 00/10] Input: cap11xx - Add support for CAP1114

[Jun Yan]

CAP1114 is a 14-channel capacitive touch sensor with 11 LED outputs
and hardware reset support.

Patches 1-4 perform driver cleanup and DT binding tweaks.
Patches 5-6 add reset-gpios support for CAP11xx.
Patches 7-10 add support for CAP1114.

Changes in v4:
- Revert cleanup operation for CAP11XX_REG_SENSOR_DELTA.
- Move the LED unit-address update operation to the CAP1114 support patch.
- Limit the CAP1114 LED unit-address range from 0x0 to 0xa.
- Link to v3:
  https://lore.kernel.org/all/20260615142103.352163-1-jerrysteve1101@gmail.com/

Changes in v3:
- Simplified the logic of the reset pin operation.
- Adjust linux,keycodes configuration for CAP11xx.
- Drop unnecessary CAP11XX_REG_SENSOR_THRESH(8).
- Checks for the presence of microchip,calib-sensitivity and
  microchip,signal-guard properties before processing them.
- Link to v2:
  https://lore.kernel.org/all/20260612072237.1177304-1-jerrysteve1101@gmail.com/

Changes in v2:
- Drop LED property tweaks, keep only reg changes and node regex
  update in DT bindings.
- Split microchip,cap1126 LED reg constraints into a separate patch.
- Replace usleep_range() with msleep() for 500 ms delay during
  reset pin handling.
- Add missing <linux/delay.h> for usleep_range() and msleep().
- Add CAP1114 to unsupported enum for microchip,signal-guard and
  microchip,calib-sensitivity
- Add constraint for linux,keycodes to support CAP1114.
- When reading CAP1114 button status, mask STATUS1 to bits 0-5
  and OR with STATUS2.
- Adjust code style.
- Link to v1:
  https://lore.kernel.org/all/20260606150458.250606-1-jerrysteve1101@gmail.com

Jun Yan (10):
  Input: cap11xx - clean up duplicate log and add probe error logs
  Input: cap11xx - remove unused register macros
  dt-bindings: input: microchip,cap11xx: Update datasheet URL and LED
    reg range
  dt-bindings: input: microchip,cap11xx: Add microchip,cap1126 LED reg
    constraints
  dt-bindings: input: microchip,cap11xx: Add reset-gpios property
  Input: cap11xx - add reset gpio support
  Input: cap11xx - refactor code for better CAP1114 support.
  Input: cap11xx - guard unsupported DT properties before parsing
  dt-bindings: input: microchip,cap11xx: Add CAP1114 support
  Input: cap11xx - add support for CAP1114

 .../bindings/input/microchip,cap11xx.yaml     |  90 +++++-
 drivers/input/keyboard/cap11xx.c              | 274 +++++++++++-------
 2 files changed, 254 insertions(+), 110 deletions(-)

--
2.54.0

[PATCH v4 01/10] Input: cap11xx - clean up duplicate log and add probe error logs

[Jun Yan]

Duplicated device detection log exists at line 537 and line 542,
which brings redundant kernel print messages. Drop one redundant
log entry to clean up dmesg output.

Meanwhile add missing error logs when I2C communication fails
during driver probe(), helping debug.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 11 ++++-------
 1 file changed, 4 insertions(+), 7 deletions(-)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 2447c1ae2166..485d8ba97723 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -512,7 +512,7 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client)
 
 	error = regmap_read(priv->regmap, CAP11XX_REG_PRODUCT_ID, &val);
 	if (error)
-		return error;
+		return dev_err_probe(dev, error, "Failed to read product ID\n");
 
 	if (val != cap->product_id) {
 		dev_err(dev, "Product ID: Got 0x%02x, expected 0x%02x\n",
@@ -522,7 +522,7 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client)
 
 	error = regmap_read(priv->regmap, CAP11XX_REG_MANUFACTURER_ID, &val);
 	if (error)
-		return error;
+		return dev_err_probe(dev, error, "Failed to read manufacturer ID\n");
 
 	if (val != CAP11XX_MANUFACTURER_ID) {
 		dev_err(dev, "Manufacturer ID: Got 0x%02x, expected 0x%02x\n",
@@ -531,11 +531,8 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client)
 	}
 
 	error = regmap_read(priv->regmap, CAP11XX_REG_REVISION, &rev);
-	if (error < 0)
-		return error;
-
-	dev_info(dev, "CAP11XX detected, model %s, revision 0x%02x\n",
-			 id->name, rev);
+	if (error)
+		return dev_err_probe(dev, error, "Failed to read revision\n");
 
 	priv->model = cap;
 
-- 
2.54.0

[PATCH v4 02/10] Input: cap11xx - remove unused register macros

[Jun Yan]

Remove unused register address macros and unused definitions in
the cap11xx_reg_defaults array and cap11xx_volatile_reg.

This cleanup reduces code clutter and makes the driver easier to
maintain without affecting functionality.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 51 --------------------------------
 1 file changed, 51 deletions(-)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 485d8ba97723..fae26f035186 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -20,53 +20,24 @@
 #define CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT	(6)
 #define CAP11XX_REG_MAIN_CONTROL_GAIN_MASK	(0xc0)
 #define CAP11XX_REG_MAIN_CONTROL_DLSEEP		BIT(4)
-#define CAP11XX_REG_GENERAL_STATUS	0x02
 #define CAP11XX_REG_SENSOR_INPUT	0x03
-#define CAP11XX_REG_NOISE_FLAG_STATUS	0x0a
 #define CAP11XX_REG_SENOR_DELTA(X)	(0x10 + (X))
 #define CAP11XX_REG_SENSITIVITY_CONTROL	0x1f
 #define CAP11XX_REG_SENSITIVITY_CONTROL_DELTA_SENSE_MASK	0x70
-#define CAP11XX_REG_CONFIG		0x20
-#define CAP11XX_REG_SENSOR_ENABLE	0x21
-#define CAP11XX_REG_SENSOR_CONFIG	0x22
-#define CAP11XX_REG_SENSOR_CONFIG2	0x23
-#define CAP11XX_REG_SAMPLING_CONFIG	0x24
-#define CAP11XX_REG_CALIBRATION		0x26
-#define CAP11XX_REG_INT_ENABLE		0x27
 #define CAP11XX_REG_REPEAT_RATE		0x28
 #define CAP11XX_REG_SIGNAL_GUARD_ENABLE	0x29
-#define CAP11XX_REG_MT_CONFIG		0x2a
-#define CAP11XX_REG_MT_PATTERN_CONFIG	0x2b
-#define CAP11XX_REG_MT_PATTERN		0x2d
-#define CAP11XX_REG_RECALIB_CONFIG	0x2f
 #define CAP11XX_REG_SENSOR_THRESH(X)	(0x30 + (X))
-#define CAP11XX_REG_SENSOR_NOISE_THRESH	0x38
-#define CAP11XX_REG_STANDBY_CHANNEL	0x40
-#define CAP11XX_REG_STANDBY_CONFIG	0x41
-#define CAP11XX_REG_STANDBY_SENSITIVITY	0x42
-#define CAP11XX_REG_STANDBY_THRESH	0x43
 #define CAP11XX_REG_CONFIG2		0x44
 #define CAP11XX_REG_CONFIG2_ALT_POL	BIT(6)
-#define CAP11XX_REG_SENSOR_BASE_CNT(X)	(0x50 + (X))
-#define CAP11XX_REG_LED_POLARITY	0x73
 #define CAP11XX_REG_LED_OUTPUT_CONTROL	0x74
 #define CAP11XX_REG_CALIB_SENSITIVITY_CONFIG	0x80
 #define CAP11XX_REG_CALIB_SENSITIVITY_CONFIG2	0x81
-
-#define CAP11XX_REG_LED_DUTY_CYCLE_1	0x90
-#define CAP11XX_REG_LED_DUTY_CYCLE_2	0x91
-#define CAP11XX_REG_LED_DUTY_CYCLE_3	0x92
 #define CAP11XX_REG_LED_DUTY_CYCLE_4	0x93
 
-#define CAP11XX_REG_LED_DUTY_MIN_MASK	(0x0f)
-#define CAP11XX_REG_LED_DUTY_MIN_MASK_SHIFT	(0)
 #define CAP11XX_REG_LED_DUTY_MAX_MASK	(0xf0)
 #define CAP11XX_REG_LED_DUTY_MAX_MASK_SHIFT	(4)
 #define CAP11XX_REG_LED_DUTY_MAX_VALUE	(15)
 
-#define CAP11XX_REG_SENSOR_CALIB	(0xb1 + (X))
-#define CAP11XX_REG_SENSOR_CALIB_LSB1	0xb9
-#define CAP11XX_REG_SENSOR_CALIB_LSB2	0xba
 #define CAP11XX_REG_PRODUCT_ID		0xfd
 #define CAP11XX_REG_MANUFACTURER_ID	0xfe
 #define CAP11XX_REG_REVISION		0xff
@@ -111,37 +82,15 @@ struct cap11xx_hw_model {
 
 static const struct reg_default cap11xx_reg_defaults[] = {
 	{ CAP11XX_REG_MAIN_CONTROL,		0x00 },
-	{ CAP11XX_REG_GENERAL_STATUS,		0x00 },
-	{ CAP11XX_REG_SENSOR_INPUT,		0x00 },
-	{ CAP11XX_REG_NOISE_FLAG_STATUS,	0x00 },
 	{ CAP11XX_REG_SENSITIVITY_CONTROL,	0x2f },
-	{ CAP11XX_REG_CONFIG,			0x20 },
-	{ CAP11XX_REG_SENSOR_ENABLE,		0x3f },
-	{ CAP11XX_REG_SENSOR_CONFIG,		0xa4 },
-	{ CAP11XX_REG_SENSOR_CONFIG2,		0x07 },
-	{ CAP11XX_REG_SAMPLING_CONFIG,		0x39 },
-	{ CAP11XX_REG_CALIBRATION,		0x00 },
-	{ CAP11XX_REG_INT_ENABLE,		0x3f },
 	{ CAP11XX_REG_REPEAT_RATE,		0x3f },
-	{ CAP11XX_REG_MT_CONFIG,		0x80 },
-	{ CAP11XX_REG_MT_PATTERN_CONFIG,	0x00 },
-	{ CAP11XX_REG_MT_PATTERN,		0x3f },
-	{ CAP11XX_REG_RECALIB_CONFIG,		0x8a },
 	{ CAP11XX_REG_SENSOR_THRESH(0),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(1),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(2),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(3),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(4),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(5),		0x40 },
-	{ CAP11XX_REG_SENSOR_NOISE_THRESH,	0x01 },
-	{ CAP11XX_REG_STANDBY_CHANNEL,		0x00 },
-	{ CAP11XX_REG_STANDBY_CONFIG,		0x39 },
-	{ CAP11XX_REG_STANDBY_SENSITIVITY,	0x02 },
-	{ CAP11XX_REG_STANDBY_THRESH,		0x40 },
 	{ CAP11XX_REG_CONFIG2,			0x40 },
-	{ CAP11XX_REG_LED_POLARITY,		0x00 },
-	{ CAP11XX_REG_SENSOR_CALIB_LSB1,	0x00 },
-	{ CAP11XX_REG_SENSOR_CALIB_LSB2,	0x00 },
 };
 
 static bool cap11xx_volatile_reg(struct device *dev, unsigned int reg)
-- 
2.54.0

Re: [PATCH v4 02/10] Input: cap11xx - remove unused register macros

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:

New issues:
- [Medium] The patch fails to remove unused definitions in `cap11xx_volatile_reg` despite the commit message claiming otherwise.

Pre-existing issues:
- [High] The threaded interrupt handler unconditionally returns IRQ_HANDLED even when I2C operations fail to clear the hardware interrupt source, risking an IRQ storm.
--

commit 8aa29f5d8b4eefa859454cdb0496fecf07ff5aa8
Author: Jun Yan <jerrysteve1101@gmail.com>

Remove unused register address macros and unused definitions in
the cap11xx_reg_defaults array and cap11xx_volatile_reg.

This cleanup reduces code clutter and makes the driver easier to
maintain without affecting functionality.

> Remove unused register address macros and unused definitions in
> the cap11xx_reg_defaults array and cap11xx_volatile_reg.

[Severity: Medium]
Will this patch actually remove the unused definitions in
cap11xx_volatile_reg?

The commit message states they are removed, but the patch doesn't modify
that function.

> diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
> index 485d8ba97723..fae26f035186 100644
> --- a/drivers/input/keyboard/cap11xx.c
> +++ b/drivers/input/keyboard/cap11xx.c
> @@ -20,53 +20,24 @@
>  #define CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT	(6)
>  #define CAP11XX_REG_MAIN_CONTROL_GAIN_MASK	(0xc0)
>  #define CAP11XX_REG_MAIN_CONTROL_DLSEEP		BIT(4)
> -#define CAP11XX_REG_GENERAL_STATUS	0x02
>  #define CAP11XX_REG_SENSOR_INPUT	0x03
> -#define CAP11XX_REG_NOISE_FLAG_STATUS	0x0a
>  #define CAP11XX_REG_SENOR_DELTA(X)	(0x10 + (X))

[Severity: Medium]
Should this macro also have been removed?

Because cap11xx_volatile_reg() was not updated, this macro and its
corresponding case entries:

	case CAP11XX_REG_SENOR_DELTA(0):
	case CAP11XX_REG_SENOR_DELTA(1):

were left in the file.

[ ... ]

>  static bool cap11xx_volatile_reg(struct device *dev, unsigned int reg)

[Severity: High]
This isn't a bug introduced by this patch, but could the error handling
in cap11xx_thread_func() risk an IRQ storm?

If an I2C communication error occurs during the interrupt handler:

cap11xx_thread_func() {
	...
	if (ret < 0)
		goto out;
	...
out:
	return IRQ_HANDLED;
}

Because this uses IRQF_ONESHOT, returning IRQ_HANDLED instructs the IRQ
subsystem to unmask the interrupt. Since the device's interrupt status
was never cleared due to the I2C failure, the interrupt line will remain
asserted.

Will this cause the interrupt to immediately fire again when unmasked,
creating an infinite loop?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260617150318.753148-1-jerrysteve1101@gmail.com?part=2

[PATCH v4 03/10] dt-bindings: input: microchip,cap11xx: Update datasheet URL and LED reg range

[Jun Yan]

- Add datasheet links for all supported CAP11xx variants.
- Update LED node regex and replace enum constraints with minimum/maximum
  for LED reg ranges in preparation for CAP1114 support.

CAP1114 has 11 LED channels. minimum/maximum constraints are easier to
maintain than long enum lists when expanding channel count later.

Drop unnecessary led unit-address pattern.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../bindings/input/microchip,cap11xx.yaml         | 15 +++++++++++++--
 1 file changed, 13 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index 7ade03f1b32b..eabf06a1163e 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -10,6 +10,15 @@ description: |
   The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive
   touch controllers and LED drivers. The device communication via I2C only.
 
+  For more product information please see the links below:
+    CAP1106: https://ww1.microchip.com/downloads/en/DeviceDoc/00001624B.pdf
+    CAP1126: https://ww1.microchip.com/downloads/en/DeviceDoc/00001623B.pdf
+    CAP1188: https://ww1.microchip.com/downloads/en/DeviceDoc/00001620C.pdf
+    CAP1203: https://ww1.microchip.com/downloads/en/DeviceDoc/00001572B.pdf
+    CAP1206: https://ww1.microchip.com/downloads/en/DeviceDoc/00001567B.pdf
+    CAP1293: https://ww1.microchip.com/downloads/en/DeviceDoc/00001566B.pdf
+    CAP1298: https://ww1.microchip.com/downloads/en/DeviceDoc/00001571B.pdf
+
 maintainers:
   - Rob Herring <robh@kernel.org>
 
@@ -131,7 +140,9 @@ patternProperties:
 
     properties:
       reg:
-        enum: [0, 1, 2, 3, 4, 5, 6, 7]
+        description: LED channel number
+        minimum: 0
+        maximum: 7
 
       label: true
 
@@ -158,7 +169,7 @@ allOf:
               - microchip,cap1298
     then:
       patternProperties:
-        "^led@[0-7]$": false
+        "^led@": false
 
   - if:
       properties:
-- 
2.54.0

Re: [PATCH v4 03/10] dt-bindings: input: microchip,cap11xx: Update datasheet URL and LED reg range

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] Incomplete Refactoring / Code and Commit Message Mismatch
--

commit e8499e0ca62db6a2ee6dc0986e7c04ea1337f6c7
Author: Jun Yan <jerrysteve1101@gmail.com>

Add datasheet links for all supported CAP11xx variants.

Update LED node regex and replace enum constraints with minimum/maximum
for LED reg ranges in preparation for CAP1114 support. Drop unnecessary
led unit-address pattern.

> diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
> index 7ade03f1b32b..eabf06a1163e 100644
> --- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
> +++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml

[ ... ]

> @@ -131,7 +140,9 @@ patternProperties:
>  
>      properties:
>        reg:
> -        enum: [0, 1, 2, 3, 4, 5, 6, 7]
> +        description: LED channel number
> +        minimum: 0
> +        maximum: 7

[Severity: Medium]
Does this fully prepare the schema for CAP1114 support as mentioned in the
commit message?

While the constraints on the reg property were updated here, the main
patternProperties definition for the LED node just above this still uses
"^led@[0-7]$".

Since CAP1114 has 11 LED channels, wouldn't the schema fail validation for
nodes like led@8 and led@9 because the top-level pattern wasn't also updated?

[ ... ]

> @@ -158,7 +169,7 @@ allOf:
>                - microchip,cap1298
>      then:
>        patternProperties:
> -        "^led@[0-7]$": false
> +        "^led@": false

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260617150318.753148-1-jerrysteve1101@gmail.com?part=3

[PATCH v4 04/10] dt-bindings: input: microchip,cap11xx: Add microchip,cap1126 LED reg constraints

[Jun Yan]

Apply per-chip LED channel limits:
- CAP1126: max 2 channels (0-1)
- CAP1188: max 8 channels (0-7)
- CAP1106, CAP12xx: no LED support

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../bindings/input/microchip,cap11xx.yaml           | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index eabf06a1163e..798035e942af 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -171,6 +171,19 @@ allOf:
       patternProperties:
         "^led@": false
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1126
+    then:
+      patternProperties:
+        "^led@":
+          properties:
+            reg:
+              maximum: 1
+
   - if:
       properties:
         compatible:
-- 
2.54.0

[PATCH v4 05/10] dt-bindings: input: microchip,cap11xx: Add reset-gpios property

[Jun Yan]

Add support for the optional reset-gpios property to describe
the active-high reset pin for CAP1126/CAP1188 devices.
Driving the GPIO high asserts reset and deep sleep, while driving
it low releases reset for normal operation.

Restrict this property to be available only on CAP1126 and CAP1188
chips, as other CAP11xx variants do not have a hardware reset pin.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../bindings/input/microchip,cap11xx.yaml     | 25 +++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index 798035e942af..b97e5b2735f1 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -49,6 +49,13 @@ properties:
       device's ALERT#/CM_IRQ# pin is connected to.
       The device only has one interrupt source.
 
+  reset-gpios:
+    description: |
+      GPIO connected to the active-high RESET pin of the chip;
+      driving it high asserts reset and deep sleep, while driving
+      it low releases reset for normal operation.
+    maxItems: 1
+
   autorepeat:
     description: |
       Enables the Linux input system's autorepeat feature on the input device.
@@ -157,6 +164,20 @@ patternProperties:
 
 allOf:
   - $ref: input.yaml
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1106
+              - microchip,cap1203
+              - microchip,cap1206
+              - microchip,cap1293
+              - microchip,cap1298
+    then:
+      properties:
+        reset-gpios: false
+
   - if:
       properties:
         compatible:
@@ -207,6 +228,8 @@ additionalProperties: false
 
 examples:
   - |
+    #include <dt-bindings/gpio/gpio.h>
+
     i2c {
       #address-cells = <1>;
       #size-cells = <0>;
@@ -228,6 +251,8 @@ examples:
                          <109>,	/* KEY_PAGEDOWN */
                          <104>;	/* KEY_PAGEUP */
 
+        reset-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+
         #address-cells = <1>;
         #size-cells = <0>;
 
-- 
2.54.0

[PATCH v4 06/10] Input: cap11xx - add reset gpio support

[Jun Yan]

Some CAP11xx devices (CAP1126/CAP1188) have a dedicated RESET pin.
Add hardware reset operation to improve device reliability and
ensure proper initialization on probe.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index fae26f035186..1db4a9090705 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -5,6 +5,7 @@
  * (c) 2014 Daniel Mack <linux@zonque.org>
  */
 
+#include <linux/delay.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
@@ -44,6 +45,9 @@
 
 #define CAP11XX_MANUFACTURER_ID	0x5d
 
+#define CAP11XX_T_RST_FILT_MIN_US	10000
+#define CAP11XX_T_RST_ON_MIN_MS		400
+
 #ifdef CONFIG_LEDS_CLASS
 struct cap11xx_led {
 	struct cap11xx_priv *priv;
@@ -56,6 +60,7 @@ struct cap11xx_priv {
 	struct regmap *regmap;
 	struct device *dev;
 	struct input_dev *idev;
+	struct gpio_desc *reset_gpio;
 	const struct cap11xx_hw_model *model;
 
 	struct cap11xx_led *leds;
@@ -459,6 +464,17 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client)
 	if (IS_ERR(priv->regmap))
 		return PTR_ERR(priv->regmap);
 
+	priv->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(priv->reset_gpio))
+		return dev_err_probe(dev, PTR_ERR(priv->reset_gpio),
+				     "Failed to get 'reset' GPIO\n");
+
+	if (priv->reset_gpio) {
+		usleep_range(CAP11XX_T_RST_FILT_MIN_US, CAP11XX_T_RST_FILT_MIN_US * 2);
+		gpiod_set_value_cansleep(priv->reset_gpio, 0);
+		msleep(CAP11XX_T_RST_ON_MIN_MS);
+	}
+
 	error = regmap_read(priv->regmap, CAP11XX_REG_PRODUCT_ID, &val);
 	if (error)
 		return dev_err_probe(dev, error, "Failed to read product ID\n");
-- 
2.54.0

[PATCH v4 07/10] Input: cap11xx - refactor code for better CAP1114 support.

[Jun Yan]

Extend cap11xx_hw_model structure to support CAP1114 with
different register offsets and hardware characteristics:

- led_output_control_reg_base: different address on CAP1114
- sensor_input_reg_base: different address on CAP1114
- num_sensor_thresholds: separate value from num_channels for CAP1114
- has_repeat_en: repeat enable support, disabled by default on CAP1114

Include linux/bits.h, update the register operations related to LEDs.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 73 +++++++++++++++++++++++---------
 1 file changed, 53 insertions(+), 20 deletions(-)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 1db4a9090705..0f19ee036e78 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -5,6 +5,7 @@
  * (c) 2014 Daniel Mack <linux@zonque.org>
  */
 
+#include <linux/bits.h>
 #include <linux/delay.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
@@ -36,7 +37,6 @@
 #define CAP11XX_REG_LED_DUTY_CYCLE_4	0x93
 
 #define CAP11XX_REG_LED_DUTY_MAX_MASK	(0xf0)
-#define CAP11XX_REG_LED_DUTY_MAX_MASK_SHIFT	(4)
 #define CAP11XX_REG_LED_DUTY_MAX_VALUE	(15)
 
 #define CAP11XX_REG_PRODUCT_ID		0xfd
@@ -77,10 +77,14 @@ struct cap11xx_priv {
 
 struct cap11xx_hw_model {
 	u8 product_id;
+	u8 led_output_control_reg_base;
+	u8 sensor_input_reg_base;
 	unsigned int num_channels;
 	unsigned int num_leds;
+	unsigned int num_sensor_thresholds;
 	bool has_gain;
 	bool has_irq_config;
+	bool has_repeat_en;
 	bool has_sensitivity_control;
 	bool has_signal_guard;
 };
@@ -211,8 +215,8 @@ static int cap11xx_init_keys(struct cap11xx_priv *priv)
 	}
 
 	if (!of_property_read_u32_array(node, "microchip,input-threshold",
-					priv->thresholds, priv->model->num_channels)) {
-		for (i = 0; i < priv->model->num_channels; i++) {
+					priv->thresholds, priv->model->num_sensor_thresholds)) {
+		for (i = 0; i < priv->model->num_sensor_thresholds; i++) {
 			if (priv->thresholds[i] > 127) {
 				dev_err(dev, "Invalid input-threshold value %u\n",
 					priv->thresholds[i]);
@@ -286,10 +290,12 @@ static int cap11xx_init_keys(struct cap11xx_priv *priv)
 	of_property_read_u32_array(node, "linux,keycodes",
 				   priv->keycodes, priv->model->num_channels);
 
-	/* Disable autorepeat. The Linux input system has its own handling. */
-	error = regmap_write(priv->regmap, CAP11XX_REG_REPEAT_RATE, 0);
-	if (error)
-		return error;
+	if (priv->model->has_repeat_en) {
+		/* Disable autorepeat. The Linux input system has its own handling. */
+		error = regmap_write(priv->regmap, CAP11XX_REG_REPEAT_RATE, 0);
+		if (error)
+			return error;
+	}
 
 	return 0;
 }
@@ -308,7 +314,7 @@ static irqreturn_t cap11xx_thread_func(int irq_num, void *data)
 	if (ret < 0)
 		goto out;
 
-	ret = regmap_read(priv->regmap, CAP11XX_REG_SENSOR_INPUT, &status);
+	ret = regmap_read(priv->regmap, priv->model->sensor_input_reg_base, &status);
 	if (ret < 0)
 		goto out;
 
@@ -362,7 +368,7 @@ static int cap11xx_led_set(struct led_classdev *cdev,
 	 * 0 (OFF) and 1 (ON).
 	 */
 	return regmap_update_bits(priv->regmap,
-				  CAP11XX_REG_LED_OUTPUT_CONTROL,
+				  priv->model->led_output_control_reg_base,
 				  BIT(led->reg),
 				  value ? BIT(led->reg) : 0);
 }
@@ -374,6 +380,7 @@ static int cap11xx_init_leds(struct device *dev,
 	struct cap11xx_led *led;
 	int cnt = of_get_child_count(node);
 	int error;
+	u32 duty_val;
 
 	if (!num_leds || !cnt)
 		return 0;
@@ -387,15 +394,18 @@ static int cap11xx_init_leds(struct device *dev,
 
 	priv->leds = led;
 
+	/* Set all LEDs to off */
 	error = regmap_update_bits(priv->regmap,
-				CAP11XX_REG_LED_OUTPUT_CONTROL, 0xff, 0);
+				   priv->model->led_output_control_reg_base,
+				   GENMASK(min(num_leds, 8) - 1, 0), 0);
 	if (error)
 		return error;
 
+	duty_val = FIELD_PREP(CAP11XX_REG_LED_DUTY_MAX_MASK,
+			      CAP11XX_REG_LED_DUTY_MAX_VALUE);
+
 	error = regmap_update_bits(priv->regmap, CAP11XX_REG_LED_DUTY_CYCLE_4,
-				CAP11XX_REG_LED_DUTY_MAX_MASK,
-				CAP11XX_REG_LED_DUTY_MAX_VALUE <<
-				CAP11XX_REG_LED_DUTY_MAX_MASK_SHIFT);
+				   CAP11XX_REG_LED_DUTY_MAX_MASK, duty_val);
 	if (error)
 		return error;
 
@@ -561,41 +571,64 @@ static int cap11xx_i2c_probe(struct i2c_client *i2c_client)
 }
 
 static const struct cap11xx_hw_model cap1106_model = {
-	.product_id = 0x55, .num_channels = 6, .num_leds = 0,
+	.product_id = 0x55,
+	.num_channels = 6, .num_leds = 0, .num_sensor_thresholds = 6,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
 	.has_gain = true,
 	.has_irq_config = true,
+	.has_repeat_en = true,
 };
 
 static const struct cap11xx_hw_model cap1126_model = {
-	.product_id = 0x53, .num_channels = 6, .num_leds = 2,
+	.product_id = 0x53,
+	.num_channels = 6, .num_leds = 2, .num_sensor_thresholds = 6,
+	.led_output_control_reg_base = CAP11XX_REG_LED_OUTPUT_CONTROL,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
 	.has_gain = true,
 	.has_irq_config = true,
+	.has_repeat_en = true,
 };
 
 static const struct cap11xx_hw_model cap1188_model = {
-	.product_id = 0x50, .num_channels = 8, .num_leds = 8,
+	.product_id = 0x50,
+	.num_channels = 8, .num_leds = 8, .num_sensor_thresholds = 8,
+	.led_output_control_reg_base = CAP11XX_REG_LED_OUTPUT_CONTROL,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
 	.has_gain = true,
 	.has_irq_config = true,
+	.has_repeat_en = true,
 };
 
 static const struct cap11xx_hw_model cap1203_model = {
-	.product_id = 0x6d, .num_channels = 3, .num_leds = 0,
+	.product_id = 0x6d,
+	.num_channels = 3, .num_leds = 0, .num_sensor_thresholds = 3,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
+	.has_repeat_en = true,
 };
 
 static const struct cap11xx_hw_model cap1206_model = {
-	.product_id = 0x67, .num_channels = 6, .num_leds = 0,
+	.product_id = 0x67,
+	.num_channels = 6, .num_leds = 0, .num_sensor_thresholds = 6,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
+	.has_repeat_en = true,
 };
 
 static const struct cap11xx_hw_model cap1293_model = {
-	.product_id = 0x6f, .num_channels = 3, .num_leds = 0,
+	.product_id = 0x6f,
+	.num_channels = 3, .num_leds = 0, .num_sensor_thresholds = 3,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
 	.has_gain = true,
+	.has_repeat_en = true,
 	.has_sensitivity_control = true,
 	.has_signal_guard = true,
 };
 
 static const struct cap11xx_hw_model cap1298_model = {
-	.product_id = 0x71, .num_channels = 8, .num_leds = 0,
+	.product_id = 0x71,
+	.num_channels = 8, .num_leds = 0, .num_sensor_thresholds = 8,
+	.sensor_input_reg_base = CAP11XX_REG_SENSOR_INPUT,
 	.has_gain = true,
+	.has_repeat_en = true,
 	.has_sensitivity_control = true,
 	.has_signal_guard = true,
 };
-- 
2.54.0

[PATCH v4 08/10] Input: cap11xx - guard unsupported DT properties before parsing

[Jun Yan]

Check of_property_present() before parsing microchip,calib-sensitivity
and microchip,signal-guard, so that models which do not support these
properties (e.g. CAP1114) skip the parsing entirely.

This prevents a potential buffer overflow in calib_sensitivities[8] and
signal_guard_inputs_mask when a model with more than 8 channels
(CAP1114 has 14) would otherwise call of_property_read_u32_array()
with num_channels as the element count.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 52 +++++++++++++++++---------------
 1 file changed, 27 insertions(+), 25 deletions(-)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 0f19ee036e78..275eb79a7193 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -231,10 +231,13 @@ static int cap11xx_init_keys(struct cap11xx_priv *priv)
 		}
 	}
 
-	if (!of_property_read_u32_array(node, "microchip,calib-sensitivity",
-					priv->calib_sensitivities,
-					priv->model->num_channels)) {
-		if (priv->model->has_sensitivity_control) {
+	if (of_property_present(node, "microchip,calib-sensitivity")) {
+		if (!priv->model->has_sensitivity_control) {
+			dev_warn(dev,
+				 "This model doesn't support 'calib-sensitivity'\n");
+		} else if (!of_property_read_u32_array(node, "microchip,calib-sensitivity",
+						       priv->calib_sensitivities,
+						       priv->model->num_channels)) {
 			for (i = 0; i < priv->model->num_channels; i++) {
 				if (!is_power_of_2(priv->calib_sensitivities[i]) ||
 				    priv->calib_sensitivities[i] > 4) {
@@ -254,32 +257,31 @@ static int cap11xx_init_keys(struct cap11xx_priv *priv)
 				if (error)
 					return error;
 			}
-		} else {
-			dev_warn(dev,
-				 "This model doesn't support 'calib-sensitivity'\n");
 		}
 	}
 
-	for (i = 0; i < priv->model->num_channels; i++) {
-		if (!of_property_read_u32_index(node, "microchip,signal-guard",
-						i, &u32_val)) {
-			if (u32_val > 1)
-				return -EINVAL;
-			if (u32_val)
-				priv->signal_guard_inputs_mask |= 0x01 << i;
-		}
-	}
-
-	if (priv->signal_guard_inputs_mask) {
-		if (priv->model->has_signal_guard) {
-			error = regmap_write(priv->regmap,
-					     CAP11XX_REG_SIGNAL_GUARD_ENABLE,
-					     priv->signal_guard_inputs_mask);
-			if (error)
-				return error;
-		} else {
+	if (of_property_present(node, "microchip,signal-guard")) {
+		if (!priv->model->has_signal_guard) {
 			dev_warn(dev,
 				 "This model doesn't support 'signal-guard'\n");
+		} else {
+			for (i = 0; i < priv->model->num_channels; i++) {
+				if (!of_property_read_u32_index(node, "microchip,signal-guard",
+								i, &u32_val)) {
+					if (u32_val > 1)
+						return -EINVAL;
+					if (u32_val)
+						priv->signal_guard_inputs_mask |= 0x01 << i;
+				}
+			}
+
+			if (priv->signal_guard_inputs_mask) {
+				error = regmap_write(priv->regmap,
+						     CAP11XX_REG_SIGNAL_GUARD_ENABLE,
+						     priv->signal_guard_inputs_mask);
+				if (error)
+					return error;
+			}
 		}
 	}
 
-- 
2.54.0

[PATCH v4 09/10] dt-bindings: input: microchip,cap11xx: Add CAP1114 support

[Jun Yan]

CAP1114 is a 14-channel capacitive touch sensor with 11 LED outputs
and hardware reset support.

Add the compatible string for CAP1114, add its datasheet URL,
update the maximum of LED channel reg, and add constraint for
linux,keycodes.

Previously, the LED reg property had a default maximum of 7 for CAP1188.
With the addition of CAP1114, the default maximum is now 11.
An if-then constraint is added to limit the LED count for CAP1188.

Update description for microchip,input-threshold: CAP1114 only provides
eight threshold entries, which does not match its total channel count.

CAP1114 does not support microchip,signal-guard and
microchip,calib-sensitivity.

Add CAP1114 to the unsupported enum list.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
---
 .../bindings/input/microchip,cap11xx.yaml     | 39 +++++++++++++++++--
 1 file changed, 36 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
index b97e5b2735f1..2a37ac252c37 100644
--- a/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
+++ b/Documentation/devicetree/bindings/input/microchip,cap11xx.yaml
@@ -12,6 +12,7 @@ description: |
 
   For more product information please see the links below:
     CAP1106: https://ww1.microchip.com/downloads/en/DeviceDoc/00001624B.pdf
+    CAP1114: https://ww1.microchip.com/downloads/en/DeviceDoc/00002444A.pdf
     CAP1126: https://ww1.microchip.com/downloads/en/DeviceDoc/00001623B.pdf
     CAP1188: https://ww1.microchip.com/downloads/en/DeviceDoc/00001620C.pdf
     CAP1203: https://ww1.microchip.com/downloads/en/DeviceDoc/00001572B.pdf
@@ -26,6 +27,7 @@ properties:
   compatible:
     enum:
       - microchip,cap1106
+      - microchip,cap1114
       - microchip,cap1126
       - microchip,cap1188
       - microchip,cap1203
@@ -62,7 +64,7 @@ properties:
 
   linux,keycodes:
     minItems: 3
-    maxItems: 8
+    maxItems: 14
     description: |
       Specifies an array of numeric keycode values to
       be used for the channels. If this property is
@@ -122,6 +124,8 @@ properties:
       is required for a touch to be registered, making the touch sensor less
       sensitive.
       The number of entries must correspond to the number of channels.
+      CAP1114 is an exception where channels 8~14 reuse the eighth entry's
+      threshold, so counts differ.
 
   microchip,calib-sensitivity:
     $ref: /schemas/types.yaml#/definitions/uint32-array
@@ -140,7 +144,7 @@ properties:
       The number of entries must correspond to the number of channels.
 
 patternProperties:
-  "^led@[0-7]$":
+  "^led@[0-9a]$":
     type: object
     description: CAP11xx LEDs
     $ref: /schemas/leds/common.yaml#
@@ -149,7 +153,7 @@ patternProperties:
       reg:
         description: LED channel number
         minimum: 0
-        maximum: 7
+        maximum: 10
 
       label: true
 
@@ -178,6 +182,21 @@ allOf:
       properties:
         reset-gpios: false
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1114
+    then:
+      properties:
+        linux,keycodes:
+          minItems: 14
+    else:
+      properties:
+        linux,keycodes:
+          maxItems: 8
+
   - if:
       properties:
         compatible:
@@ -205,12 +224,26 @@ allOf:
             reg:
               maximum: 1
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - microchip,cap1188
+    then:
+      patternProperties:
+        "^led@":
+          properties:
+            reg:
+              maximum: 7
+
   - if:
       properties:
         compatible:
           contains:
             enum:
               - microchip,cap1106
+              - microchip,cap1114
               - microchip,cap1126
               - microchip,cap1188
               - microchip,cap1203
-- 
2.54.0

[PATCH v4 10/10] Input: cap11xx - add support for CAP1114

[Jun Yan]

CAP1114 is a 14-channel capacitive touch sensor with 11 LED outputs
and hardware reset support.

The CAP1114 uses two control registers for LED output management and
requires two button status registers for touch input state reporting.

By default, channels CS8~CS14 operate as a single grouped block.
Set the corresponding register enable bit to enable these channels as
independent touch inputs. Note these channels share the input threshold
of the eighth entry, causing num_sensor_thresholds to differ from
num_channels.

Signed-off-by: Jun Yan <jerrysteve1101@gmail.com>
---
 drivers/input/keyboard/cap11xx.c | 73 ++++++++++++++++++++++++++++++--
 1 file changed, 69 insertions(+), 4 deletions(-)

diff --git a/drivers/input/keyboard/cap11xx.c b/drivers/input/keyboard/cap11xx.c
index 275eb79a7193..865c58533eb9 100644
--- a/drivers/input/keyboard/cap11xx.c
+++ b/drivers/input/keyboard/cap11xx.c
@@ -18,6 +18,12 @@
 #include <linux/gpio/consumer.h>
 #include <linux/bitfield.h>
 
+#define CAP1114_REG_BUTTON_STATUS1	0x03
+#define CAP1114_REG_BUTTON_STATUS2	0x04
+#define CAP1114_REG_CONFIG2			0x40
+#define CAP1114_REG_CONFIG2_VOL_UP_DOWN	BIT(1)
+#define CAP1114_REG_LED_OUTPUT_CONTROL1	0x73
+
 #define CAP11XX_REG_MAIN_CONTROL	0x00
 #define CAP11XX_REG_MAIN_CONTROL_GAIN_SHIFT	(6)
 #define CAP11XX_REG_MAIN_CONTROL_GAIN_MASK	(0xc0)
@@ -83,6 +89,7 @@ struct cap11xx_hw_model {
 	unsigned int num_leds;
 	unsigned int num_sensor_thresholds;
 	bool has_gain;
+	bool has_grouped_sensors;
 	bool has_irq_config;
 	bool has_repeat_en;
 	bool has_sensitivity_control;
@@ -99,6 +106,8 @@ static const struct reg_default cap11xx_reg_defaults[] = {
 	{ CAP11XX_REG_SENSOR_THRESH(3),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(4),		0x40 },
 	{ CAP11XX_REG_SENSOR_THRESH(5),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(6),		0x40 },
+	{ CAP11XX_REG_SENSOR_THRESH(7),		0x40 },
 	{ CAP11XX_REG_CONFIG2,			0x40 },
 };
 
@@ -107,6 +116,12 @@ static bool cap11xx_volatile_reg(struct device *dev, unsigned int reg)
 	switch (reg) {
 	case CAP11XX_REG_MAIN_CONTROL:
 	case CAP11XX_REG_SENSOR_INPUT:
+	/*
+	 * CAP1114_REG_BUTTON_STATUS1 (CAP11XX_REG_SENSOR_INPUT) and
+	 * CAP1114_REG_BUTTON_STATUS2 is volatile for the CAP1114,
+	 * which supports more than 8 touch channels.
+	 */
+	case CAP1114_REG_BUTTON_STATUS2:
 	case CAP11XX_REG_SENOR_DELTA(0):
 	case CAP11XX_REG_SENOR_DELTA(1):
 	case CAP11XX_REG_SENOR_DELTA(2):
@@ -292,6 +307,17 @@ static int cap11xx_init_keys(struct cap11xx_priv *priv)
 	of_property_read_u32_array(node, "linux,keycodes",
 				   priv->keycodes, priv->model->num_channels);
 
+	/*
+	 * CAP1114 needs dedicated configuration to split
+	 * grouped sensors into independent inputs.
+	 */
+	if (priv->model->has_grouped_sensors) {
+		error = regmap_set_bits(priv->regmap, CAP1114_REG_CONFIG2,
+					CAP1114_REG_CONFIG2_VOL_UP_DOWN);
+		if (error)
+			return error;
+	}
+
 	if (priv->model->has_repeat_en) {
 		/* Disable autorepeat. The Linux input system has its own handling. */
 		error = regmap_write(priv->regmap, CAP11XX_REG_REPEAT_RATE, 0);
@@ -320,6 +346,21 @@ static irqreturn_t cap11xx_thread_func(int irq_num, void *data)
 	if (ret < 0)
 		goto out;
 
+	if (priv->model->num_channels > 8) {
+		unsigned int status2;
+
+		ret = regmap_read(priv->regmap, priv->model->sensor_input_reg_base + 1, &status2);
+		if (ret < 0)
+			goto out;
+
+		/*
+		 * CAP1114 STATUS1 register only contains data for the first 6 channels.
+		 * the remaining channels is stored in STATUS2.
+		 */
+		status &= GENMASK(5, 0);
+		status |= FIELD_PREP(GENMASK(13, 6), status2);
+	}
+
 	for (i = 0; i < priv->idev->keycodemax; i++)
 		input_report_key(priv->idev, priv->keycodes[i],
 				 status & (1 << i));
@@ -369,10 +410,16 @@ static int cap11xx_led_set(struct led_classdev *cdev,
 	 * limitation. Brightness levels per LED are either
 	 * 0 (OFF) and 1 (ON).
 	 */
-	return regmap_update_bits(priv->regmap,
-				  priv->model->led_output_control_reg_base,
-				  BIT(led->reg),
-				  value ? BIT(led->reg) : 0);
+	if (led->reg >= 8)
+		return regmap_update_bits(priv->regmap,
+					  priv->model->led_output_control_reg_base + 1,
+					  BIT(led->reg - 8),
+					  value ? BIT(led->reg - 8) : 0);
+	else
+		return regmap_update_bits(priv->regmap,
+					  priv->model->led_output_control_reg_base,
+					  BIT(led->reg),
+					  value ? BIT(led->reg) : 0);
 }
 
 static int cap11xx_init_leds(struct device *dev,
@@ -403,6 +450,14 @@ static int cap11xx_init_leds(struct device *dev,
 	if (error)
 		return error;
 
+	if (num_leds > 8) {
+		error = regmap_update_bits(priv->regmap,
+					   priv->model->led_output_control_reg_base + 1,
+					   GENMASK(num_leds - 8 - 1, 0), 0);
+		if (error)
+			return error;
+	}
+
 	duty_val = FIELD_PREP(CAP11XX_REG_LED_DUTY_MAX_MASK,
 			      CAP11XX_REG_LED_DUTY_MAX_VALUE);
 
@@ -581,6 +636,14 @@ static const struct cap11xx_hw_model cap1106_model = {
 	.has_repeat_en = true,
 };
 
+static const struct cap11xx_hw_model cap1114_model = {
+	.product_id = 0x3a,
+	.num_channels = 14, .num_leds = 11, .num_sensor_thresholds = 8,
+	.led_output_control_reg_base = CAP1114_REG_LED_OUTPUT_CONTROL1,
+	.sensor_input_reg_base = CAP1114_REG_BUTTON_STATUS1,
+	.has_grouped_sensors = true,
+};
+
 static const struct cap11xx_hw_model cap1126_model = {
 	.product_id = 0x53,
 	.num_channels = 6, .num_leds = 2, .num_sensor_thresholds = 6,
@@ -637,6 +700,7 @@ static const struct cap11xx_hw_model cap1298_model = {
 
 static const struct of_device_id cap11xx_dt_ids[] = {
 	{ .compatible = "microchip,cap1106", .data = &cap1106_model },
+	{ .compatible = "microchip,cap1114", .data = &cap1114_model },
 	{ .compatible = "microchip,cap1126", .data = &cap1126_model },
 	{ .compatible = "microchip,cap1188", .data = &cap1188_model },
 	{ .compatible = "microchip,cap1203", .data = &cap1203_model },
@@ -649,6 +713,7 @@ MODULE_DEVICE_TABLE(of, cap11xx_dt_ids);
 
 static const struct i2c_device_id cap11xx_i2c_ids[] = {
 	{ .name = "cap1106", .driver_data = (kernel_ulong_t)&cap1106_model },
+	{ .name = "cap1114", .driver_data = (kernel_ulong_t)&cap1114_model },
 	{ .name = "cap1126", .driver_data = (kernel_ulong_t)&cap1126_model },
 	{ .name = "cap1188", .driver_data = (kernel_ulong_t)&cap1188_model },
 	{ .name = "cap1203", .driver_data = (kernel_ulong_t)&cap1203_model },
-- 
2.54.0