* [PATCH v2 02/10] HID: intel-ish-hid: Hide members of struct ishtp_cl_device
From: Srinivas Pandruvada @ 2019-03-18 19:14 UTC (permalink / raw)
To: jikos, benjamin.tissoires; +Cc: linux-input, linux-kernel, Srinivas Pandruvada
In-Reply-To: <20190318191428.6527-1-srinivas.pandruvada@linux.intel.com>
ISH clients don't need to access any field of struct ishtp_cl_device. To
avoid this create an interface functions instead where it is required.
In the case of ishtp_cl_allocate(), modify the parameters so that the
clients don't have to dereference.
Clients can also use tracing, here a new interface is added to get the
common trace function pointer, instead of direct call.
The new interface functions defined in one external header file, named
intel-ish-client-if.h. This is the only header files all ISHTP clients
must include.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
---
drivers/hid/intel-ish-hid/ishtp-hid-client.c | 56 +++++++++++---------
drivers/hid/intel-ish-hid/ishtp-hid.c | 4 +-
drivers/hid/intel-ish-hid/ishtp-hid.h | 2 +-
drivers/hid/intel-ish-hid/ishtp/bus.c | 27 ++++++++++
drivers/hid/intel-ish-hid/ishtp/client.c | 4 +-
drivers/hid/intel-ish-hid/ishtp/client.h | 2 +-
include/linux/intel-ish-client-if.h | 18 +++++++
7 files changed, 84 insertions(+), 29 deletions(-)
create mode 100644 include/linux/intel-ish-client-if.h
diff --git a/drivers/hid/intel-ish-hid/ishtp-hid-client.c b/drivers/hid/intel-ish-hid/ishtp-hid-client.c
index b86290611a5f..17d5bd4f52c1 100644
--- a/drivers/hid/intel-ish-hid/ishtp-hid-client.c
+++ b/drivers/hid/intel-ish-hid/ishtp-hid-client.c
@@ -15,6 +15,7 @@
#include <linux/module.h>
#include <linux/hid.h>
+#include <linux/intel-ish-client-if.h>
#include <linux/sched.h>
#include "ishtp/ishtp-dev.h"
#include "ishtp/client.h"
@@ -24,6 +25,8 @@
#define HID_CL_RX_RING_SIZE 32
#define HID_CL_TX_RING_SIZE 16
+#define cl_data_to_dev(client_data) ishtp_device(client_data->cl_device)
+
/**
* report_bad_packets() - Report bad packets
* @hid_ishtp_cl: Client instance to get stats
@@ -39,7 +42,7 @@ static void report_bad_packet(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
struct hostif_msg *recv_msg = recv_buf;
struct ishtp_cl_data *client_data = hid_ishtp_cl->client_data;
- dev_err(&client_data->cl_device->dev, "[hid-ish]: BAD packet %02X\n"
+ dev_err(cl_data_to_dev(client_data), "[hid-ish]: BAD packet %02X\n"
"total_bad=%u cur_pos=%u\n"
"[%02X %02X %02X %02X]\n"
"payload_len=%u\n"
@@ -85,7 +88,7 @@ static void process_recv(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
do {
if (cur_pos + sizeof(struct hostif_msg) > total_len) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: error, received %u which is less than data header %u\n",
(unsigned int)data_len,
(unsigned int)sizeof(struct hostif_msg_hdr));
@@ -124,12 +127,12 @@ static void process_recv(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
client_data->hid_dev_count = (unsigned int)*payload;
if (!client_data->hid_devices)
client_data->hid_devices = devm_kcalloc(
- &client_data->cl_device->dev,
+ cl_data_to_dev(client_data),
client_data->hid_dev_count,
sizeof(struct device_info),
GFP_KERNEL);
if (!client_data->hid_devices) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"Mem alloc failed for hid device info\n");
wake_up_interruptible(&client_data->init_wait);
break;
@@ -137,7 +140,7 @@ static void process_recv(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
for (i = 0; i < client_data->hid_dev_count; ++i) {
if (1 + sizeof(struct device_info) * i >=
payload_len) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: [ENUM_DEVICES]: content size %zu is bigger than payload_len %zu\n",
1 + sizeof(struct device_info)
* i, payload_len);
@@ -172,7 +175,7 @@ static void process_recv(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
}
if (!client_data->hid_descr[curr_hid_dev])
client_data->hid_descr[curr_hid_dev] =
- devm_kmalloc(&client_data->cl_device->dev,
+ devm_kmalloc(cl_data_to_dev(client_data),
payload_len, GFP_KERNEL);
if (client_data->hid_descr[curr_hid_dev]) {
memcpy(client_data->hid_descr[curr_hid_dev],
@@ -197,7 +200,7 @@ static void process_recv(struct ishtp_cl *hid_ishtp_cl, void *recv_buf,
}
if (!client_data->report_descr[curr_hid_dev])
client_data->report_descr[curr_hid_dev] =
- devm_kmalloc(&client_data->cl_device->dev,
+ devm_kmalloc(cl_data_to_dev(client_data),
payload_len, GFP_KERNEL);
if (client_data->report_descr[curr_hid_dev]) {
memcpy(client_data->report_descr[curr_hid_dev],
@@ -516,12 +519,12 @@ static int ishtp_enum_enum_devices(struct ishtp_cl *hid_ishtp_cl)
sizeof(struct hostif_msg));
}
if (!client_data->enum_devices_done) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: timed out waiting for enum_devices\n");
return -ETIMEDOUT;
}
if (!client_data->hid_devices) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: failed to allocate HID dev structures\n");
return -ENOMEM;
}
@@ -564,13 +567,13 @@ static int ishtp_get_hid_descriptor(struct ishtp_cl *hid_ishtp_cl, int index)
client_data->hid_descr_done,
3 * HZ);
if (!client_data->hid_descr_done) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: timed out for hid_descr_done\n");
return -EIO;
}
if (!client_data->hid_descr[index]) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: allocation HID desc fail\n");
return -ENOMEM;
}
@@ -611,12 +614,12 @@ static int ishtp_get_report_descriptor(struct ishtp_cl *hid_ishtp_cl,
client_data->report_descr_done,
3 * HZ);
if (!client_data->report_descr_done) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: timed out for report descr\n");
return -EIO;
}
if (!client_data->report_descr[index]) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: failed to alloc report descr\n");
return -ENOMEM;
}
@@ -646,12 +649,12 @@ static int hid_ishtp_cl_init(struct ishtp_cl *hid_ishtp_cl, int reset)
int i;
int rv;
- dev_dbg(&client_data->cl_device->dev, "%s\n", __func__);
+ dev_dbg(cl_data_to_dev(client_data), "%s\n", __func__);
hid_ishtp_trace(client_data, "%s reset flag: %d\n", __func__, reset);
rv = ishtp_cl_link(hid_ishtp_cl, ISHTP_HOST_CLIENT_ID_ANY);
if (rv) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"ishtp_cl_link failed\n");
return -ENOMEM;
}
@@ -666,7 +669,7 @@ static int hid_ishtp_cl_init(struct ishtp_cl *hid_ishtp_cl, int reset)
fw_client = ishtp_fw_cl_get_client(dev, &hid_ishtp_guid);
if (!fw_client) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"ish client uuid not found\n");
return -ENOENT;
}
@@ -676,7 +679,7 @@ static int hid_ishtp_cl_init(struct ishtp_cl *hid_ishtp_cl, int reset)
rv = ishtp_cl_connect(hid_ishtp_cl);
if (rv) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"client connect fail\n");
goto err_cl_unlink;
}
@@ -707,7 +710,7 @@ static int hid_ishtp_cl_init(struct ishtp_cl *hid_ishtp_cl, int reset)
if (!reset) {
rv = ishtp_hid_probe(i, client_data);
if (rv) {
- dev_err(&client_data->cl_device->dev,
+ dev_err(cl_data_to_dev(client_data),
"[hid-ish]: HID probe for #%u failed: %d\n",
i, rv);
goto err_cl_disconnect;
@@ -763,7 +766,7 @@ static void hid_ishtp_cl_reset_handler(struct work_struct *work)
hid_ishtp_cl_deinit(hid_ishtp_cl);
- hid_ishtp_cl = ishtp_cl_allocate(cl_device->ishtp_dev);
+ hid_ishtp_cl = ishtp_cl_allocate(cl_device);
if (!hid_ishtp_cl)
return;
@@ -777,15 +780,17 @@ static void hid_ishtp_cl_reset_handler(struct work_struct *work)
rv = hid_ishtp_cl_init(hid_ishtp_cl, 1);
if (!rv)
break;
- dev_err(&client_data->cl_device->dev, "Retry reset init\n");
+ dev_err(cl_data_to_dev(client_data), "Retry reset init\n");
}
if (rv) {
- dev_err(&client_data->cl_device->dev, "Reset Failed\n");
+ dev_err(cl_data_to_dev(client_data), "Reset Failed\n");
hid_ishtp_trace(client_data, "%s Failed hid_ishtp_cl %p\n",
__func__, hid_ishtp_cl);
}
}
+void (*hid_print_trace)(void *dev, const char *format, ...);
+
/**
* hid_ishtp_cl_probe() - ISHTP client driver probe
* @cl_device: ISHTP client device instance
@@ -803,12 +808,13 @@ static int hid_ishtp_cl_probe(struct ishtp_cl_device *cl_device)
if (!cl_device)
return -ENODEV;
- client_data = devm_kzalloc(&cl_device->dev, sizeof(*client_data),
+ client_data = devm_kzalloc(ishtp_device(cl_device),
+ sizeof(*client_data),
GFP_KERNEL);
if (!client_data)
return -ENOMEM;
- hid_ishtp_cl = ishtp_cl_allocate(cl_device->ishtp_dev);
+ hid_ishtp_cl = ishtp_cl_allocate(cl_device);
if (!hid_ishtp_cl)
return -ENOMEM;
@@ -822,6 +828,8 @@ static int hid_ishtp_cl_probe(struct ishtp_cl_device *cl_device)
INIT_WORK(&client_data->work, hid_ishtp_cl_reset_handler);
+ hid_print_trace = ishtp_trace_callback(cl_device);
+
rv = hid_ishtp_cl_init(hid_ishtp_cl, 0);
if (rv) {
ishtp_cl_free(hid_ishtp_cl);
@@ -848,7 +856,7 @@ static int hid_ishtp_cl_remove(struct ishtp_cl_device *cl_device)
hid_ishtp_trace(client_data, "%s hid_ishtp_cl %p\n", __func__,
hid_ishtp_cl);
- dev_dbg(&cl_device->dev, "%s\n", __func__);
+ dev_dbg(ishtp_device(cl_device), "%s\n", __func__);
hid_ishtp_cl->state = ISHTP_CL_DISCONNECTING;
ishtp_cl_disconnect(hid_ishtp_cl);
ishtp_put_device(cl_device);
diff --git a/drivers/hid/intel-ish-hid/ishtp-hid.c b/drivers/hid/intel-ish-hid/ishtp-hid.c
index 5c7e127b0483..95a5b87d9105 100644
--- a/drivers/hid/intel-ish-hid/ishtp-hid.c
+++ b/drivers/hid/intel-ish-hid/ishtp-hid.c
@@ -14,6 +14,7 @@
*/
#include <linux/hid.h>
+#include <linux/intel-ish-client-if.h>
#include <uapi/linux/input.h>
#include "ishtp/client.h"
#include "ishtp-hid.h"
@@ -241,7 +242,8 @@ int ishtp_hid_probe(unsigned int cur_hid_dev,
hid->ll_driver = &ishtp_hid_ll_driver;
hid->bus = BUS_INTEL_ISHTP;
- hid->dev.parent = &client_data->cl_device->dev;
+ hid->dev.parent = ishtp_device(client_data->cl_device);
+
hid->version = le16_to_cpu(ISH_HID_VERSION);
hid->vendor = le16_to_cpu(client_data->hid_devices[cur_hid_dev].vid);
hid->product = le16_to_cpu(client_data->hid_devices[cur_hid_dev].pid);
diff --git a/drivers/hid/intel-ish-hid/ishtp-hid.h b/drivers/hid/intel-ish-hid/ishtp-hid.h
index 40663639e43b..8af44e855a49 100644
--- a/drivers/hid/intel-ish-hid/ishtp-hid.h
+++ b/drivers/hid/intel-ish-hid/ishtp-hid.h
@@ -24,7 +24,7 @@
#define IS_RESPONSE 0x80
/* Used to dump to Linux trace buffer, if enabled */
-#define hid_ishtp_trace(client, ...) \
+#define hid_ishtp_trace(client, ...) \
client->cl_device->ishtp_dev->print_log(\
client->cl_device->ishtp_dev, __VA_ARGS__)
diff --git a/drivers/hid/intel-ish-hid/ishtp/bus.c b/drivers/hid/intel-ish-hid/ishtp/bus.c
index 6348fee8aadc..308853eab91c 100644
--- a/drivers/hid/intel-ish-hid/ishtp/bus.c
+++ b/drivers/hid/intel-ish-hid/ishtp/bus.c
@@ -827,6 +827,33 @@ int ishtp_use_dma_transfer(void)
return ishtp_use_dma;
}
+/**
+ * ishtp_device() - Return device pointer
+ *
+ * This interface is used to return device pointer from ishtp_cl_device
+ * instance.
+ *
+ * Return: device *.
+ */
+struct device *ishtp_device(struct ishtp_cl_device *device)
+{
+ return &device->dev;
+}
+EXPORT_SYMBOL(ishtp_device);
+
+/**
+ * ishtp_trace_callback() - Return trace callback
+ *
+ * This interface is used to return trace callback function pointer.
+ *
+ * Return: void *.
+ */
+void *ishtp_trace_callback(struct ishtp_cl_device *cl_device)
+{
+ return cl_device->ishtp_dev->print_log;
+}
+EXPORT_SYMBOL(ishtp_trace_callback);
+
/**
* ishtp_bus_register() - Function to register bus
*
diff --git a/drivers/hid/intel-ish-hid/ishtp/client.c b/drivers/hid/intel-ish-hid/ishtp/client.c
index faeccdb1475b..760e48a368a8 100644
--- a/drivers/hid/intel-ish-hid/ishtp/client.c
+++ b/drivers/hid/intel-ish-hid/ishtp/client.c
@@ -126,7 +126,7 @@ static void ishtp_cl_init(struct ishtp_cl *cl, struct ishtp_device *dev)
*
* Return: The allocated client instance or NULL on failure
*/
-struct ishtp_cl *ishtp_cl_allocate(struct ishtp_device *dev)
+struct ishtp_cl *ishtp_cl_allocate(struct ishtp_cl_device *cl_device)
{
struct ishtp_cl *cl;
@@ -134,7 +134,7 @@ struct ishtp_cl *ishtp_cl_allocate(struct ishtp_device *dev)
if (!cl)
return NULL;
- ishtp_cl_init(cl, dev);
+ ishtp_cl_init(cl, cl_device->ishtp_dev);
return cl;
}
EXPORT_SYMBOL(ishtp_cl_allocate);
diff --git a/drivers/hid/intel-ish-hid/ishtp/client.h b/drivers/hid/intel-ish-hid/ishtp/client.h
index e0df3eb611e6..992625891a6c 100644
--- a/drivers/hid/intel-ish-hid/ishtp/client.h
+++ b/drivers/hid/intel-ish-hid/ishtp/client.h
@@ -170,7 +170,7 @@ static inline bool ishtp_cl_cmp_id(const struct ishtp_cl *cl1,
}
/* exported functions from ISHTP under client management scope */
-struct ishtp_cl *ishtp_cl_allocate(struct ishtp_device *dev);
+struct ishtp_cl *ishtp_cl_allocate(struct ishtp_cl_device *cl_device);
void ishtp_cl_free(struct ishtp_cl *cl);
int ishtp_cl_link(struct ishtp_cl *cl, int id);
void ishtp_cl_unlink(struct ishtp_cl *cl);
diff --git a/include/linux/intel-ish-client-if.h b/include/linux/intel-ish-client-if.h
new file mode 100644
index 000000000000..11e285172735
--- /dev/null
+++ b/include/linux/intel-ish-client-if.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Intel ISH client Interface definitions
+ *
+ * Copyright (c) 2019, Intel Corporation.
+ */
+
+#ifndef _INTEL_ISH_CLIENT_IF_H_
+#define _INTEL_ISH_CLIENT_IF_H_
+
+struct ishtp_cl_device;
+
+/* Get the device * from ishtp device instance */
+struct device *ishtp_device(struct ishtp_cl_device *cl_device);
+/* Trace interface for clients */
+void *ishtp_trace_callback(struct ishtp_cl_device *cl_device);
+
+#endif /* _INTEL_ISH_CLIENT_IF_H_ */
--
2.17.2
^ permalink raw reply related
* [PATCH v2 01/10] HID: intel-ish-hid: Add match callback to ishtp bus type
From: Srinivas Pandruvada @ 2019-03-18 19:14 UTC (permalink / raw)
To: jikos, benjamin.tissoires; +Cc: linux-input, linux-kernel, Hong Liu
In-Reply-To: <20190318191428.6527-1-srinivas.pandruvada@linux.intel.com>
From: Hong Liu <hong.liu@intel.com>
Currently we depend on the guid check in ishtp_cl_driver.probe to match
the device and driver. However Linux device core first calls the match()
callback to decide the matching of driver and device, and then does some
preparation before calling the driver probe function. If we return error
in the driver probe, it needs to tear down all the preparation work and
retry with next driver.
Adding the match callback can avoid the unnecessary entry into unmatched
driver probe function for ishtp clients reported by FW.
Signed-off-by: Hong Liu <hong.liu@intel.com>
---
drivers/hid/intel-ish-hid/ishtp-hid-client.c | 5 +----
drivers/hid/intel-ish-hid/ishtp/bus.c | 21 ++++++++++++++++++++
drivers/hid/intel-ish-hid/ishtp/bus.h | 1 +
3 files changed, 23 insertions(+), 4 deletions(-)
diff --git a/drivers/hid/intel-ish-hid/ishtp-hid-client.c b/drivers/hid/intel-ish-hid/ishtp-hid-client.c
index 58773a3b5150..b86290611a5f 100644
--- a/drivers/hid/intel-ish-hid/ishtp-hid-client.c
+++ b/drivers/hid/intel-ish-hid/ishtp-hid-client.c
@@ -803,10 +803,6 @@ static int hid_ishtp_cl_probe(struct ishtp_cl_device *cl_device)
if (!cl_device)
return -ENODEV;
- if (!guid_equal(&hid_ishtp_guid,
- &cl_device->fw_client->props.protocol_name))
- return -ENODEV;
-
client_data = devm_kzalloc(&cl_device->dev, sizeof(*client_data),
GFP_KERNEL);
if (!client_data)
@@ -937,6 +933,7 @@ static const struct dev_pm_ops hid_ishtp_pm_ops = {
static struct ishtp_cl_driver hid_ishtp_cl_driver = {
.name = "ish-hid",
+ .guid = &hid_ishtp_guid,
.probe = hid_ishtp_cl_probe,
.remove = hid_ishtp_cl_remove,
.reset = hid_ishtp_cl_reset,
diff --git a/drivers/hid/intel-ish-hid/ishtp/bus.c b/drivers/hid/intel-ish-hid/ishtp/bus.c
index d5f4b6438d86..6348fee8aadc 100644
--- a/drivers/hid/intel-ish-hid/ishtp/bus.c
+++ b/drivers/hid/intel-ish-hid/ishtp/bus.c
@@ -219,6 +219,26 @@ static int ishtp_cl_device_probe(struct device *dev)
return driver->probe(device);
}
+/**
+ * ishtp_cl_bus_match() - Bus match() callback
+ * @dev: the device structure
+ * @drv: the driver structure
+ *
+ * This is a bus match callback, called when a new ishtp_cl_device is
+ * registered during ishtp bus client enumeration. Use the guid_t in
+ * drv and dev to decide whether they match or not.
+ *
+ * Return: 1 if dev & drv matches, 0 otherwise.
+ */
+static int ishtp_cl_bus_match(struct device *dev, struct device_driver *drv)
+{
+ struct ishtp_cl_device *device = to_ishtp_cl_device(dev);
+ struct ishtp_cl_driver *driver = to_ishtp_cl_driver(drv);
+
+ return guid_equal(driver->guid,
+ &device->fw_client->props.protocol_name);
+}
+
/**
* ishtp_cl_device_remove() - Bus remove() callback
* @dev: the device structure
@@ -372,6 +392,7 @@ static struct bus_type ishtp_cl_bus_type = {
.name = "ishtp",
.dev_groups = ishtp_cl_dev_groups,
.probe = ishtp_cl_device_probe,
+ .match = ishtp_cl_bus_match,
.remove = ishtp_cl_device_remove,
.pm = &ishtp_cl_bus_dev_pm_ops,
.uevent = ishtp_cl_uevent,
diff --git a/drivers/hid/intel-ish-hid/ishtp/bus.h b/drivers/hid/intel-ish-hid/ishtp/bus.h
index 4cf7ad586c37..c96e7fb42f01 100644
--- a/drivers/hid/intel-ish-hid/ishtp/bus.h
+++ b/drivers/hid/intel-ish-hid/ishtp/bus.h
@@ -64,6 +64,7 @@ struct ishtp_cl_device {
struct ishtp_cl_driver {
struct device_driver driver;
const char *name;
+ const guid_t *guid;
int (*probe)(struct ishtp_cl_device *dev);
int (*remove)(struct ishtp_cl_device *dev);
int (*reset)(struct ishtp_cl_device *dev);
--
2.17.2
^ permalink raw reply related
* [PATCH v2 00/10] HID: intel-ish-hid: Clean up external interfaces
From: Srinivas Pandruvada @ 2019-03-18 19:14 UTC (permalink / raw)
To: jikos, benjamin.tissoires; +Cc: linux-input, linux-kernel, Srinivas Pandruvada
NOT FOR kernel v5.1.
v2
- Rebased on the top of
"HID: intel-ish: enable raw interface to HID devices on ISH"
which Jiri already applied.
- Also exported devc pointer for DMA
No functional changes are expected with this series. I am posting this now
because of usage of ISH in ChromeOS Embedded Controller.
https://lkml.org/lkml/2019/2/24/26
I want to make sure that API is restricted before more development and posting
there.
Currently only one ISH client is using ISH transport. But it is changing now
with the development of other clients using ISH transport. Some of these
clients which are targeted for Linux based OS only laptops, are not using
HID to export sensors. As more clients are getting developed it is important
that the external interface for ISH transport only allows what clients need.
Currently the header files used by clients "client.h" and "ishtp-dev.h"
include other ISH header files. Also clients access fields from structure
which also has other fields which are only used by ISH transort.
So this series introduces one header file "linux/intel-ish-client-if.h".
This header files doesn't include any other ISH transport header files.
There are interface functions defined so that clients never have to directly
access any ISH transort structures.
Also clients don't have to match there GUID in probe. They will be only
probbed if their GUID matches, which is passed as driver registry.
Hong Liu (1):
HID: intel-ish-hid: Add match callback to ishtp bus type
Srinivas Pandruvada (9):
HID: intel-ish-hid: Hide members of struct ishtp_cl_device
HID: intel-ish-hid: Simplify ishtp_cl_link()
HID: intel-ish-hid: Move driver registry functions
HID: intel-ish-hid: Store ishtp_cl_device instance in device
HID: intel-ish-hid: Move the common functions from client.h
HID: intel-ish-hid: Add interface functions for struct ishtp_cl
HID: intel-ish-hid: Move functions related to bus and device
HID: intel-ish-hid: Use the new interface functions in HID ish client
HID: intel-ish-hid: Add interface function for PCI device pointer
drivers/hid/intel-ish-hid/ishtp-hid-client.c | 131 ++++++++++---------
drivers/hid/intel-ish-hid/ishtp-hid.c | 6 +-
drivers/hid/intel-ish-hid/ishtp-hid.h | 6 +-
drivers/hid/intel-ish-hid/ishtp/bus.c | 96 +++++++++++++-
drivers/hid/intel-ish-hid/ishtp/bus.h | 37 +-----
drivers/hid/intel-ish-hid/ishtp/client.c | 60 +++++++--
drivers/hid/intel-ish-hid/ishtp/client.h | 24 ----
drivers/hid/intel-ish-hid/ishtp/ishtp-dev.h | 31 -----
include/linux/intel-ish-client-if.h | 112 ++++++++++++++++
9 files changed, 325 insertions(+), 178 deletions(-)
create mode 100644 include/linux/intel-ish-client-if.h
--
2.17.2
^ permalink raw reply
* Re: [RESEND PATCH v6 00/11] mfd: add support for max77650 PMIC
From: Bartosz Golaszewski @ 2019-03-18 17:44 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: Linux Kernel Mailing List, open list:GPIO SUBSYSTEM, devicetree,
Linux Input, Linux LED Subsystem, Linux PM list,
Bartosz Golaszewski
In-Reply-To: <20190318174040.17899-1-brgl@bgdev.pl>
pon., 18 mar 2019 o 18:40 Bartosz Golaszewski <brgl@bgdev.pl> napisał(a):
>
> From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
>
> This series missed the last merge window so resending rebased on top
> of v5.1-rc1 with no functional changes.
>
> ---
>
> This series adds support for max77650 ultra low-power PMIC. It provides
> the core mfd driver and a set of five sub-drivers for the regulator,
> power supply, gpio, leds and input subsystems.
>
> Patches 1-4 add the DT binding documents. Patch 5 documents mfd_add_devices().
> Patches 6-10 add all drivers. Last patch adds a MAINTAINERS entry for this
> device.
>
> The regulator part is already upstream.
>
> v1 -> v2:
> =========
>
> General:
> - use C++ style comments for the SPDX license identifier and the
> copyright header
> - s/MODULE_LICENSE("GPL")/MODULE_LICENSE("GPL v2")/
> - lookup the virtual interrupt numbers in the MFD driver, setup
> resources for child devices and use platform_get_irq_byname()
> in sub-drivers
> - picked up review tags
> - use devm_request_any_context_irq() for interrupt requests
>
> LEDs:
> - changed the max77650_leds_ prefix to max77650_led_
> - drop the max77650_leds structure as the only field it held was the
> regmap pointer, move said pointer to struct max77650_led
> - change the driver name to "max77650-led"
> - drop the last return value check and return the result of
> regmap_write() directly
> - change the labeling scheme to one consistent with other LED drivers
>
> ONKEY:
> - drop the key reporting helper and call the input functions directly
> from interrupt handlers
> - rename the rv local variable to error
> - drop parent device asignment
>
> Regulator:
> - drop the unnecessary init_data lookup from the driver code
> - drop unnecessary include
>
> Charger:
> - disable the charger on driver remove
> - change the power supply type to POWER_SUPPLY_TYPE_USB
>
> GPIO:
> - drop interrupt support until we have correct implementation of hierarchical
> irqs in gpiolib
>
> v2 -> v3:
> =========
>
> General:
> - dropped regulator patches as they're already in Mark Brown's branch
>
> LED:
> - fix the compatible string in the DT binding example
> - use the max_brightness property
> - use a common prefix ("MAX77650_LED") for all defines in the driver
>
> MFD:
> - add the MODULE_DEVICE_TABLE()
> - add a sentinel to the of_device_id array
> - constify the pointers to irq names
> - use an enum instead of defines for interrupt indexes
>
> v3 -> v4:
> =========
>
> GPIO:
> - as discussed with Linus Walleij: the gpio-controller is now part of
> the core mfd module (we don't spawn a sub-node anymore), the binding
> document for GPIO has been dropped, the GPIO properties have been
> defined in the binding document for the mfd core, the interrupt
> functionality has been reintroduced with the irq directly passed from
> the mfd part
> - due to the above changes the Reviewed-by tag from Linus was dropped
>
> v4 -> v5:
> =========
>
> General:
> - add a patch documenting mfd_add_devices()
>
> MFD:
> - pass the regmap irq_chip irq domain to mfd over mfd_add_devices so that
> the hw interrupts from resources can be correctly mapped to virtual irqs
> - remove the enum listing cell indexes
> - extend Kconfig help
> - add a link to the programming manual
> - use REGMAP_IRQ_REG() for regmap interrupts (except for GPI which has
> is composed of two hw interrupts for rising and falling edge)
> - add error messages in probe
> - use PLATFORM_DEVID_NONE constant in devm_mfd_add_devices()
> - set irq_base to 0 in regmap_add_irq_chip() as other users to, it's only
> relevant if it's > 0
>
> Charger:
> - use non-maxim specific property names for minimum input voltage and current
> limit
> - code shrink by using the enable/disable charger helpers everywhere
> - use more descriptive names for constants
>
> Onkey:
> - use EV_SW event type for slide mode
>
> LED:
> - remove stray " from Kconfig help
>
> v5 -> v6:
> =========
>
> MFD:
> - remove stray spaces in the binding document
> - rename the example dt node
> - remove unnecessary interrupt-parent property from the bindings
>
> LED:
> - add a missing dependency on LEDS_CLASS to Kconfig
>
> Onkey:
> - use boolean for the slide button property
>
> Charger:
> - fix the property names in DT example
> - make constants even more readable
>
> Bartosz Golaszewski (11):
> dt-bindings: mfd: add DT bindings for max77650
> dt-bindings: power: supply: add DT bindings for max77650
> dt-bindings: leds: add DT bindings for max77650
> dt-bindings: input: add DT bindings for max77650
> mfd: core: document mfd_add_devices()
> mfd: max77650: new core mfd driver
> power: supply: max77650: add support for battery charger
> gpio: max77650: add GPIO support
> leds: max77650: add LEDs support
> input: max77650: add onkey support
> MAINTAINERS: add an entry for max77650 mfd driver
>
> .../bindings/input/max77650-onkey.txt | 26 ++
> .../bindings/leds/leds-max77650.txt | 57 +++
> .../devicetree/bindings/mfd/max77650.txt | 46 +++
> .../power/supply/max77650-charger.txt | 27 ++
> MAINTAINERS | 14 +
> drivers/gpio/Kconfig | 7 +
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-max77650.c | 190 +++++++++
> drivers/input/misc/Kconfig | 9 +
> drivers/input/misc/Makefile | 1 +
> drivers/input/misc/max77650-onkey.c | 121 ++++++
> drivers/leds/Kconfig | 6 +
> drivers/leds/Makefile | 1 +
> drivers/leds/leds-max77650.c | 147 +++++++
> drivers/mfd/Kconfig | 14 +
> drivers/mfd/Makefile | 1 +
> drivers/mfd/max77650.c | 234 +++++++++++
> drivers/mfd/mfd-core.c | 14 +
> drivers/power/supply/Kconfig | 7 +
> drivers/power/supply/Makefile | 1 +
> drivers/power/supply/max77650-charger.c | 366 ++++++++++++++++++
> include/linux/mfd/max77650.h | 59 +++
> 22 files changed, 1349 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/input/max77650-onkey.txt
> create mode 100644 Documentation/devicetree/bindings/leds/leds-max77650.txt
> create mode 100644 Documentation/devicetree/bindings/mfd/max77650.txt
> create mode 100644 Documentation/devicetree/bindings/power/supply/max77650-charger.txt
> create mode 100644 drivers/gpio/gpio-max77650.c
> create mode 100644 drivers/input/misc/max77650-onkey.c
> create mode 100644 drivers/leds/leds-max77650.c
> create mode 100644 drivers/mfd/max77650.c
> create mode 100644 drivers/power/supply/max77650-charger.c
> create mode 100644 include/linux/mfd/max77650.h
>
> --
> 2.20.1
>
Sorry for spamming - I got a strange error from git send-email:
Died at /<snip!>libexec/git-core/git-send-email line 1542.
Bart
^ permalink raw reply
* [RESEND PATCH v6 11/11] MAINTAINERS: add an entry for max77650 mfd driver
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I plan on extending this set of drivers so add myself as maintainer.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
MAINTAINERS | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index e17ebf70b548..6f19949111d5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9397,6 +9397,20 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/max9860.txt
F: sound/soc/codecs/max9860.*
+MAXIM MAX77650 PMIC MFD DRIVER
+M: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+L: linux-kernel@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/*/*max77650.txt
+F: Documentation/devicetree/bindings/*/max77650*.txt
+F: include/linux/mfd/max77650.h
+F: drivers/mfd/max77650.c
+F: drivers/regulator/max77650-regulator.c
+F: drivers/power/supply/max77650-charger.c
+F: drivers/input/misc/max77650-onkey.c
+F: drivers/leds/leds-max77650.c
+F: drivers/gpio/gpio-max77650.c
+
MAXIM MAX77802 PMIC REGULATOR DEVICE DRIVER
M: Javier Martinez Canillas <javier@dowhile0.org>
L: linux-kernel@vger.kernel.org
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 10/11] input: max77650: add onkey support
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for the push- and slide-button events for max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
drivers/input/misc/Kconfig | 9 +++
drivers/input/misc/Makefile | 1 +
drivers/input/misc/max77650-onkey.c | 121 ++++++++++++++++++++++++++++
3 files changed, 131 insertions(+)
create mode 100644 drivers/input/misc/max77650-onkey.c
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index e15ed1bb8558..85bc675eecd3 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -190,6 +190,15 @@ config INPUT_M68K_BEEP
tristate "M68k Beeper support"
depends on M68K
+config INPUT_MAX77650_ONKEY
+ tristate "Maxim MAX77650 ONKEY support"
+ depends on MFD_MAX77650
+ help
+ Support the ONKEY of the MAX77650 PMIC as an input device.
+
+ To compile this driver as a module, choose M here: the module
+ will be called max77650-onkey.
+
config INPUT_MAX77693_HAPTIC
tristate "MAXIM MAX77693/MAX77843 haptic controller support"
depends on (MFD_MAX77693 || MFD_MAX77843) && PWM
diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile
index b936c5b1d4ac..ffd72161c79b 100644
--- a/drivers/input/misc/Makefile
+++ b/drivers/input/misc/Makefile
@@ -43,6 +43,7 @@ obj-$(CONFIG_INPUT_IXP4XX_BEEPER) += ixp4xx-beeper.o
obj-$(CONFIG_INPUT_KEYSPAN_REMOTE) += keyspan_remote.o
obj-$(CONFIG_INPUT_KXTJ9) += kxtj9.o
obj-$(CONFIG_INPUT_M68K_BEEP) += m68kspkr.o
+obj-$(CONFIG_INPUT_MAX77650_ONKEY) += max77650-onkey.o
obj-$(CONFIG_INPUT_MAX77693_HAPTIC) += max77693-haptic.o
obj-$(CONFIG_INPUT_MAX8925_ONKEY) += max8925_onkey.o
obj-$(CONFIG_INPUT_MAX8997_HAPTIC) += max8997_haptic.o
diff --git a/drivers/input/misc/max77650-onkey.c b/drivers/input/misc/max77650-onkey.c
new file mode 100644
index 000000000000..fbf6caab7217
--- /dev/null
+++ b/drivers/input/misc/max77650-onkey.c
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// ONKEY driver for MAXIM 77650/77651 charger/power-supply.
+
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define MAX77650_ONKEY_MODE_MASK BIT(3)
+#define MAX77650_ONKEY_MODE_PUSH 0x00
+#define MAX77650_ONKEY_MODE_SLIDE BIT(3)
+
+struct max77650_onkey {
+ struct input_dev *input;
+ unsigned int code;
+};
+
+static irqreturn_t max77650_onkey_falling(int irq, void *data)
+{
+ struct max77650_onkey *onkey = data;
+
+ input_report_key(onkey->input, onkey->code, 0);
+ input_sync(onkey->input);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t max77650_onkey_rising(int irq, void *data)
+{
+ struct max77650_onkey *onkey = data;
+
+ input_report_key(onkey->input, onkey->code, 1);
+ input_sync(onkey->input);
+
+ return IRQ_HANDLED;
+}
+
+static int max77650_onkey_probe(struct platform_device *pdev)
+{
+ int irq_r, irq_f, error, mode;
+ struct max77650_onkey *onkey;
+ struct device *dev, *parent;
+ struct regmap *map;
+ unsigned int type;
+
+ dev = &pdev->dev;
+ parent = dev->parent;
+
+ map = dev_get_regmap(parent, NULL);
+ if (!map)
+ return -ENODEV;
+
+ onkey = devm_kzalloc(dev, sizeof(*onkey), GFP_KERNEL);
+ if (!onkey)
+ return -ENOMEM;
+
+ error = device_property_read_u32(dev, "linux,code", &onkey->code);
+ if (error)
+ onkey->code = KEY_POWER;
+
+ if (device_property_read_bool(dev, "maxim,onkey-slide")) {
+ mode = MAX77650_ONKEY_MODE_SLIDE;
+ type = EV_SW;
+ } else {
+ mode = MAX77650_ONKEY_MODE_PUSH;
+ type = EV_KEY;
+ }
+
+ error = regmap_update_bits(map, MAX77650_REG_CNFG_GLBL,
+ MAX77650_ONKEY_MODE_MASK, mode);
+ if (error)
+ return error;
+
+ irq_f = platform_get_irq_byname(pdev, "nEN_F");
+ if (irq_f < 0)
+ return irq_f;
+
+ irq_r = platform_get_irq_byname(pdev, "nEN_R");
+ if (irq_r < 0)
+ return irq_r;
+
+ onkey->input = devm_input_allocate_device(dev);
+ if (!onkey->input)
+ return -ENOMEM;
+
+ onkey->input->name = "max77650_onkey";
+ onkey->input->phys = "max77650_onkey/input0";
+ onkey->input->id.bustype = BUS_I2C;
+ input_set_capability(onkey->input, type, onkey->code);
+
+ error = devm_request_any_context_irq(dev, irq_f, max77650_onkey_falling,
+ IRQF_ONESHOT, "onkey-down", onkey);
+ if (error < 0)
+ return error;
+
+ error = devm_request_any_context_irq(dev, irq_r, max77650_onkey_rising,
+ IRQF_ONESHOT, "onkey-up", onkey);
+ if (error < 0)
+ return error;
+
+ return input_register_device(onkey->input);
+}
+
+static struct platform_driver max77650_onkey_driver = {
+ .driver = {
+ .name = "max77650-onkey",
+ },
+ .probe = max77650_onkey_probe,
+};
+module_platform_driver(max77650_onkey_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 ONKEY driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 09/11] leds: max77650: add LEDs support
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This adds basic support for LEDs for the max77650 PMIC. The device has
three current sinks for driving LEDs.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
---
drivers/leds/Kconfig | 6 ++
drivers/leds/Makefile | 1 +
drivers/leds/leds-max77650.c | 147 +++++++++++++++++++++++++++++++++++
3 files changed, 154 insertions(+)
create mode 100644 drivers/leds/leds-max77650.c
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index a72f97fca57b..d8c70cc6a714 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -608,6 +608,12 @@ config LEDS_TLC591XX
This option enables support for Texas Instruments TLC59108
and TLC59116 LED controllers.
+config LEDS_MAX77650
+ tristate "LED support for Maxim MAX77650 PMIC"
+ depends on LEDS_CLASS && MFD_MAX77650
+ help
+ LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
+
config LEDS_MAX77693
tristate "LED support for MAX77693 Flash"
depends on LEDS_CLASS_FLASH
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index 4c1b0054f379..f48b2404dbb7 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -61,6 +61,7 @@ obj-$(CONFIG_LEDS_MC13783) += leds-mc13783.o
obj-$(CONFIG_LEDS_NS2) += leds-ns2.o
obj-$(CONFIG_LEDS_NETXBIG) += leds-netxbig.o
obj-$(CONFIG_LEDS_ASIC3) += leds-asic3.o
+obj-$(CONFIG_LEDS_MAX77650) += leds-max77650.o
obj-$(CONFIG_LEDS_MAX77693) += leds-max77693.o
obj-$(CONFIG_LEDS_MAX8997) += leds-max8997.o
obj-$(CONFIG_LEDS_LM355x) += leds-lm355x.o
diff --git a/drivers/leds/leds-max77650.c b/drivers/leds/leds-max77650.c
new file mode 100644
index 000000000000..6b74ce9cac12
--- /dev/null
+++ b/drivers/leds/leds-max77650.c
@@ -0,0 +1,147 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// LED driver for MAXIM 77650/77651 charger/power-supply.
+
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define MAX77650_LED_NUM_LEDS 3
+
+#define MAX77650_LED_A_BASE 0x40
+#define MAX77650_LED_B_BASE 0x43
+
+#define MAX77650_LED_BR_MASK GENMASK(4, 0)
+#define MAX77650_LED_EN_MASK GENMASK(7, 6)
+
+#define MAX77650_LED_MAX_BRIGHTNESS MAX77650_LED_BR_MASK
+
+/* Enable EN_LED_MSTR. */
+#define MAX77650_LED_TOP_DEFAULT BIT(0)
+
+#define MAX77650_LED_ENABLE GENMASK(7, 6)
+#define MAX77650_LED_DISABLE 0x00
+
+#define MAX77650_LED_A_DEFAULT MAX77650_LED_DISABLE
+/* 100% on duty */
+#define MAX77650_LED_B_DEFAULT GENMASK(3, 0)
+
+struct max77650_led {
+ struct led_classdev cdev;
+ struct regmap *map;
+ unsigned int regA;
+ unsigned int regB;
+};
+
+static struct max77650_led *max77650_to_led(struct led_classdev *cdev)
+{
+ return container_of(cdev, struct max77650_led, cdev);
+}
+
+static int max77650_led_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct max77650_led *led = max77650_to_led(cdev);
+ int val, mask;
+
+ mask = MAX77650_LED_BR_MASK | MAX77650_LED_EN_MASK;
+
+ if (brightness == LED_OFF)
+ val = MAX77650_LED_DISABLE;
+ else
+ val = MAX77650_LED_ENABLE | brightness;
+
+ return regmap_update_bits(led->map, led->regA, mask, val);
+}
+
+static int max77650_led_probe(struct platform_device *pdev)
+{
+ struct device_node *of_node, *child;
+ struct max77650_led *leds, *led;
+ struct device *parent;
+ struct device *dev;
+ struct regmap *map;
+ const char *label;
+ int rv, num_leds;
+ u32 reg;
+
+ dev = &pdev->dev;
+ parent = dev->parent;
+ of_node = dev->of_node;
+
+ if (!of_node)
+ return -ENODEV;
+
+ leds = devm_kcalloc(dev, sizeof(*leds),
+ MAX77650_LED_NUM_LEDS, GFP_KERNEL);
+ if (!leds)
+ return -ENOMEM;
+
+ map = dev_get_regmap(dev->parent, NULL);
+ if (!map)
+ return -ENODEV;
+
+ num_leds = of_get_child_count(of_node);
+ if (!num_leds || num_leds > MAX77650_LED_NUM_LEDS)
+ return -ENODEV;
+
+ for_each_child_of_node(of_node, child) {
+ rv = of_property_read_u32(child, "reg", ®);
+ if (rv || reg >= MAX77650_LED_NUM_LEDS)
+ return -EINVAL;
+
+ led = &leds[reg];
+ led->map = map;
+ led->regA = MAX77650_LED_A_BASE + reg;
+ led->regB = MAX77650_LED_B_BASE + reg;
+ led->cdev.brightness_set_blocking = max77650_led_brightness_set;
+ led->cdev.max_brightness = MAX77650_LED_MAX_BRIGHTNESS;
+
+ label = of_get_property(child, "label", NULL);
+ if (!label) {
+ led->cdev.name = "max77650::";
+ } else {
+ led->cdev.name = devm_kasprintf(dev, GFP_KERNEL,
+ "max77650:%s", label);
+ if (!led->cdev.name)
+ return -ENOMEM;
+ }
+
+ of_property_read_string(child, "linux,default-trigger",
+ &led->cdev.default_trigger);
+
+ rv = devm_of_led_classdev_register(dev, child, &led->cdev);
+ if (rv)
+ return rv;
+
+ rv = regmap_write(map, led->regA, MAX77650_LED_A_DEFAULT);
+ if (rv)
+ return rv;
+
+ rv = regmap_write(map, led->regB, MAX77650_LED_B_DEFAULT);
+ if (rv)
+ return rv;
+ }
+
+ return regmap_write(map,
+ MAX77650_REG_CNFG_LED_TOP,
+ MAX77650_LED_TOP_DEFAULT);
+}
+
+static struct platform_driver max77650_led_driver = {
+ .driver = {
+ .name = "max77650-led",
+ },
+ .probe = max77650_led_probe,
+};
+module_platform_driver(max77650_led_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 LED driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 08/11] gpio: max77650: add GPIO support
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add GPIO support for max77650 mfd device. This PMIC exposes a single
GPIO line.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/gpio/Kconfig | 7 ++
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-max77650.c | 190 +++++++++++++++++++++++++++++++++++
3 files changed, 198 insertions(+)
create mode 100644 drivers/gpio/gpio-max77650.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 3f50526a771f..c4f912104440 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1112,6 +1112,13 @@ config GPIO_MAX77620
driver also provides interrupt support for each of the gpios.
Say yes here to enable the max77620 to be used as gpio controller.
+config GPIO_MAX77650
+ tristate "Maxim MAX77650/77651 GPIO support"
+ depends on MFD_MAX77650
+ help
+ GPIO driver for MAX77650/77651 PMIC from Maxim Semiconductor.
+ These chips have a single pin that can be configured as GPIO.
+
config GPIO_MSIC
bool "Intel MSIC mixed signal gpio support"
depends on (X86 || COMPILE_TEST) && MFD_INTEL_MSIC
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 54d55274b93a..075722d8317d 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -80,6 +80,7 @@ obj-$(CONFIG_GPIO_MAX7300) += gpio-max7300.o
obj-$(CONFIG_GPIO_MAX7301) += gpio-max7301.o
obj-$(CONFIG_GPIO_MAX732X) += gpio-max732x.o
obj-$(CONFIG_GPIO_MAX77620) += gpio-max77620.o
+obj-$(CONFIG_GPIO_MAX77650) += gpio-max77650.o
obj-$(CONFIG_GPIO_MB86S7X) += gpio-mb86s7x.o
obj-$(CONFIG_GPIO_MENZ127) += gpio-menz127.o
obj-$(CONFIG_GPIO_MERRIFIELD) += gpio-merrifield.o
diff --git a/drivers/gpio/gpio-max77650.c b/drivers/gpio/gpio-max77650.c
new file mode 100644
index 000000000000..3f03f4e8956c
--- /dev/null
+++ b/drivers/gpio/gpio-max77650.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// GPIO driver for MAXIM 77650/77651 charger/power-supply.
+
+#include <linux/gpio/driver.h>
+#include <linux/i2c.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define MAX77650_GPIO_DIR_MASK BIT(0)
+#define MAX77650_GPIO_INVAL_MASK BIT(1)
+#define MAX77650_GPIO_DRV_MASK BIT(2)
+#define MAX77650_GPIO_OUTVAL_MASK BIT(3)
+#define MAX77650_GPIO_DEBOUNCE_MASK BIT(4)
+
+#define MAX77650_GPIO_DIR_OUT 0x00
+#define MAX77650_GPIO_DIR_IN BIT(0)
+#define MAX77650_GPIO_OUT_LOW 0x00
+#define MAX77650_GPIO_OUT_HIGH BIT(3)
+#define MAX77650_GPIO_DRV_OPEN_DRAIN 0x00
+#define MAX77650_GPIO_DRV_PUSH_PULL BIT(2)
+#define MAX77650_GPIO_DEBOUNCE BIT(4)
+
+#define MAX77650_GPIO_DIR_BITS(_reg) \
+ ((_reg) & MAX77650_GPIO_DIR_MASK)
+#define MAX77650_GPIO_INVAL_BITS(_reg) \
+ (((_reg) & MAX77650_GPIO_INVAL_MASK) >> 1)
+
+struct max77650_gpio_chip {
+ struct regmap *map;
+ struct gpio_chip gc;
+ int irq;
+};
+
+static int max77650_gpio_direction_input(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+
+ return regmap_update_bits(chip->map,
+ MAX77650_REG_CNFG_GPIO,
+ MAX77650_GPIO_DIR_MASK,
+ MAX77650_GPIO_DIR_IN);
+}
+
+static int max77650_gpio_direction_output(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+ int mask, regval;
+
+ mask = MAX77650_GPIO_DIR_MASK | MAX77650_GPIO_OUTVAL_MASK;
+ regval = value ? MAX77650_GPIO_OUT_HIGH : MAX77650_GPIO_OUT_LOW;
+ regval |= MAX77650_GPIO_DIR_OUT;
+
+ return regmap_update_bits(chip->map,
+ MAX77650_REG_CNFG_GPIO, mask, regval);
+}
+
+static void max77650_gpio_set_value(struct gpio_chip *gc,
+ unsigned int offset, int value)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+ int rv, regval;
+
+ regval = value ? MAX77650_GPIO_OUT_HIGH : MAX77650_GPIO_OUT_LOW;
+
+ rv = regmap_update_bits(chip->map, MAX77650_REG_CNFG_GPIO,
+ MAX77650_GPIO_OUTVAL_MASK, regval);
+ if (rv)
+ dev_err(gc->parent, "cannot set GPIO value: %d\n", rv);
+}
+
+static int max77650_gpio_get_value(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+ unsigned int val;
+ int rv;
+
+ rv = regmap_read(chip->map, MAX77650_REG_CNFG_GPIO, &val);
+ if (rv)
+ return rv;
+
+ return MAX77650_GPIO_INVAL_BITS(val);
+}
+
+static int max77650_gpio_get_direction(struct gpio_chip *gc,
+ unsigned int offset)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+ unsigned int val;
+ int rv;
+
+ rv = regmap_read(chip->map, MAX77650_REG_CNFG_GPIO, &val);
+ if (rv)
+ return rv;
+
+ return MAX77650_GPIO_DIR_BITS(val);
+}
+
+static int max77650_gpio_set_config(struct gpio_chip *gc,
+ unsigned int offset, unsigned long cfg)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+
+ switch (pinconf_to_config_param(cfg)) {
+ case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+ return regmap_update_bits(chip->map,
+ MAX77650_REG_CNFG_GPIO,
+ MAX77650_GPIO_DRV_MASK,
+ MAX77650_GPIO_DRV_OPEN_DRAIN);
+ case PIN_CONFIG_DRIVE_PUSH_PULL:
+ return regmap_update_bits(chip->map,
+ MAX77650_REG_CNFG_GPIO,
+ MAX77650_GPIO_DRV_MASK,
+ MAX77650_GPIO_DRV_PUSH_PULL);
+ case PIN_CONFIG_INPUT_DEBOUNCE:
+ return regmap_update_bits(chip->map,
+ MAX77650_REG_CNFG_GPIO,
+ MAX77650_GPIO_DEBOUNCE_MASK,
+ MAX77650_GPIO_DEBOUNCE);
+ default:
+ return -ENOTSUPP;
+ }
+}
+
+static int max77650_gpio_to_irq(struct gpio_chip *gc, unsigned int offset)
+{
+ struct max77650_gpio_chip *chip = gpiochip_get_data(gc);
+
+ return chip->irq;
+}
+
+static int max77650_gpio_probe(struct platform_device *pdev)
+{
+ struct max77650_gpio_chip *chip;
+ struct device *dev, *parent;
+ struct i2c_client *i2c;
+
+ dev = &pdev->dev;
+ parent = dev->parent;
+ i2c = to_i2c_client(parent);
+
+ chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->map = dev_get_regmap(parent, NULL);
+ if (!chip->map)
+ return -ENODEV;
+
+ chip->irq = platform_get_irq_byname(pdev, "GPI");
+ if (chip->irq < 0)
+ return chip->irq;
+
+ chip->gc.base = -1;
+ chip->gc.ngpio = 1;
+ chip->gc.label = i2c->name;
+ chip->gc.parent = dev;
+ chip->gc.owner = THIS_MODULE;
+ chip->gc.can_sleep = true;
+
+ chip->gc.direction_input = max77650_gpio_direction_input;
+ chip->gc.direction_output = max77650_gpio_direction_output;
+ chip->gc.set = max77650_gpio_set_value;
+ chip->gc.get = max77650_gpio_get_value;
+ chip->gc.get_direction = max77650_gpio_get_direction;
+ chip->gc.set_config = max77650_gpio_set_config;
+ chip->gc.to_irq = max77650_gpio_to_irq;
+
+ return devm_gpiochip_add_data(dev, &chip->gc, chip);
+}
+
+static struct platform_driver max77650_gpio_driver = {
+ .driver = {
+ .name = "max77650-gpio",
+ },
+ .probe = max77650_gpio_probe,
+};
+module_platform_driver(max77650_gpio_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 GPIO driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 07/11] power: supply: max77650: add support for battery charger
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add basic support for the battery charger for max77650 PMIC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
drivers/power/supply/Kconfig | 7 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/max77650-charger.c | 366 ++++++++++++++++++++++++
3 files changed, 374 insertions(+)
create mode 100644 drivers/power/supply/max77650-charger.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index e901b9879e7e..0230c96fa94d 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -499,6 +499,13 @@ config CHARGER_DETECTOR_MAX14656
Revision 1.2 and can be found e.g. in Kindle 4/5th generation
readers and certain LG devices.
+config CHARGER_MAX77650
+ tristate "Maxim MAX77650 battery charger driver"
+ depends on MFD_MAX77650
+ help
+ Say Y to enable support for the battery charger control of MAX77650
+ PMICs.
+
config CHARGER_MAX77693
tristate "Maxim MAX77693 battery charger driver"
depends on MFD_MAX77693
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index b731c2a9b695..b73eb8c5c1a9 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -70,6 +70,7 @@ obj-$(CONFIG_CHARGER_MANAGER) += charger-manager.o
obj-$(CONFIG_CHARGER_LTC3651) += ltc3651-charger.o
obj-$(CONFIG_CHARGER_MAX14577) += max14577_charger.o
obj-$(CONFIG_CHARGER_DETECTOR_MAX14656) += max14656_charger_detector.o
+obj-$(CONFIG_CHARGER_MAX77650) += max77650-charger.o
obj-$(CONFIG_CHARGER_MAX77693) += max77693_charger.o
obj-$(CONFIG_CHARGER_MAX8997) += max8997_charger.o
obj-$(CONFIG_CHARGER_MAX8998) += max8998_charger.o
diff --git a/drivers/power/supply/max77650-charger.c b/drivers/power/supply/max77650-charger.c
new file mode 100644
index 000000000000..1abaeec9ddd3
--- /dev/null
+++ b/drivers/power/supply/max77650-charger.c
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// Battery charger driver for MAXIM 77650/77651 charger/power-supply.
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+
+#define MAX77650_CHARGER_ENABLED BIT(0)
+#define MAX77650_CHARGER_DISABLED 0x00
+#define MAX77650_CHARGER_CHG_EN_MASK BIT(0)
+
+#define MAX77650_CHG_DETAILS_MASK GENMASK(7, 4)
+#define MAX77650_CHG_DETAILS_BITS(_reg) \
+ (((_reg) & MAX77650_CHG_DETAILS_MASK) >> 4)
+
+/* Charger is OFF. */
+#define MAX77650_CHG_OFF 0x00
+/* Charger is in prequalification mode. */
+#define MAX77650_CHG_PREQ 0x01
+/* Charger is in fast-charge constant current mode. */
+#define MAX77650_CHG_ON_CURR 0x02
+/* Charger is in JEITA modified fast-charge constant-current mode. */
+#define MAX77650_CHG_ON_CURR_JEITA 0x03
+/* Charger is in fast-charge constant-voltage mode. */
+#define MAX77650_CHG_ON_VOLT 0x04
+/* Charger is in JEITA modified fast-charge constant-voltage mode. */
+#define MAX77650_CHG_ON_VOLT_JEITA 0x05
+/* Charger is in top-off mode. */
+#define MAX77650_CHG_ON_TOPOFF 0x06
+/* Charger is in JEITA modified top-off mode. */
+#define MAX77650_CHG_ON_TOPOFF_JEITA 0x07
+/* Charger is done. */
+#define MAX77650_CHG_DONE 0x08
+/* Charger is JEITA modified done. */
+#define MAX77650_CHG_DONE_JEITA 0x09
+/* Charger is suspended due to a prequalification timer fault. */
+#define MAX77650_CHG_SUSP_PREQ_TIM_FAULT 0x0a
+/* Charger is suspended due to a fast-charge timer fault. */
+#define MAX77650_CHG_SUSP_FAST_CHG_TIM_FAULT 0x0b
+/* Charger is suspended due to a battery temperature fault. */
+#define MAX77650_CHG_SUSP_BATT_TEMP_FAULT 0x0c
+
+#define MAX77650_CHGIN_DETAILS_MASK GENMASK(3, 2)
+#define MAX77650_CHGIN_DETAILS_BITS(_reg) \
+ (((_reg) & MAX77650_CHGIN_DETAILS_MASK) >> 2)
+
+#define MAX77650_CHGIN_UNDERVOLTAGE_LOCKOUT 0x00
+#define MAX77650_CHGIN_OVERVOLTAGE_LOCKOUT 0x01
+#define MAX77650_CHGIN_OKAY 0x11
+
+#define MAX77650_CHARGER_CHG_MASK BIT(1)
+#define MAX77650_CHARGER_CHG_CHARGING(_reg) \
+ (((_reg) & MAX77650_CHARGER_CHG_MASK) > 1)
+
+#define MAX77650_CHARGER_VCHGIN_MIN_MASK 0xc0
+#define MAX77650_CHARGER_VCHGIN_MIN_SHIFT(_val) ((_val) << 5)
+
+#define MAX77650_CHARGER_ICHGIN_LIM_MASK 0x1c
+#define MAX77650_CHARGER_ICHGIN_LIM_SHIFT(_val) ((_val) << 2)
+
+struct max77650_charger_data {
+ struct regmap *map;
+ struct device *dev;
+};
+
+static enum power_supply_property max77650_charger_properties[] = {
+ POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_CHARGE_TYPE
+};
+
+static const unsigned int max77650_charger_vchgin_min_table[] = {
+ 4000000, 4100000, 4200000, 4300000, 4400000, 4500000, 4600000, 4700000
+};
+
+static const unsigned int max77650_charger_ichgin_lim_table[] = {
+ 95000, 190000, 285000, 380000, 475000
+};
+
+static int max77650_charger_set_vchgin_min(struct max77650_charger_data *chg,
+ unsigned int val)
+{
+ int i, rv;
+
+ for (i = 0; i < ARRAY_SIZE(max77650_charger_vchgin_min_table); i++) {
+ if (val == max77650_charger_vchgin_min_table[i]) {
+ rv = regmap_update_bits(chg->map,
+ MAX77650_REG_CNFG_CHG_B,
+ MAX77650_CHARGER_VCHGIN_MIN_MASK,
+ MAX77650_CHARGER_VCHGIN_MIN_SHIFT(i));
+ if (rv)
+ return rv;
+
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static int max77650_charger_set_ichgin_lim(struct max77650_charger_data *chg,
+ unsigned int val)
+{
+ int i, rv;
+
+ for (i = 0; i < ARRAY_SIZE(max77650_charger_ichgin_lim_table); i++) {
+ if (val == max77650_charger_ichgin_lim_table[i]) {
+ rv = regmap_update_bits(chg->map,
+ MAX77650_REG_CNFG_CHG_B,
+ MAX77650_CHARGER_ICHGIN_LIM_MASK,
+ MAX77650_CHARGER_ICHGIN_LIM_SHIFT(i));
+ if (rv)
+ return rv;
+
+ return 0;
+ }
+ }
+
+ return -EINVAL;
+}
+
+static int max77650_charger_enable(struct max77650_charger_data *chg)
+{
+ int rv;
+
+ rv = regmap_update_bits(chg->map,
+ MAX77650_REG_CNFG_CHG_B,
+ MAX77650_CHARGER_CHG_EN_MASK,
+ MAX77650_CHARGER_ENABLED);
+ if (rv)
+ dev_err(chg->dev, "unable to enable the charger: %d\n", rv);
+
+ return rv;
+}
+
+static int max77650_charger_disable(struct max77650_charger_data *chg)
+{
+ int rv;
+
+ rv = regmap_update_bits(chg->map,
+ MAX77650_REG_CNFG_CHG_B,
+ MAX77650_CHARGER_CHG_EN_MASK,
+ MAX77650_CHARGER_DISABLED);
+ if (rv)
+ dev_err(chg->dev, "unable to disable the charger: %d\n", rv);
+
+ return rv;
+}
+
+static irqreturn_t max77650_charger_check_status(int irq, void *data)
+{
+ struct max77650_charger_data *chg = data;
+ int rv, reg;
+
+ rv = regmap_read(chg->map, MAX77650_REG_STAT_CHG_B, ®);
+ if (rv) {
+ dev_err(chg->dev,
+ "unable to read the charger status: %d\n", rv);
+ return IRQ_HANDLED;
+ }
+
+ switch (MAX77650_CHGIN_DETAILS_BITS(reg)) {
+ case MAX77650_CHGIN_UNDERVOLTAGE_LOCKOUT:
+ dev_err(chg->dev, "undervoltage lockout detected, disabling charger\n");
+ max77650_charger_disable(chg);
+ break;
+ case MAX77650_CHGIN_OVERVOLTAGE_LOCKOUT:
+ dev_err(chg->dev, "overvoltage lockout detected, disabling charger\n");
+ max77650_charger_disable(chg);
+ break;
+ case MAX77650_CHGIN_OKAY:
+ max77650_charger_enable(chg);
+ break;
+ default:
+ /* May be 0x10 - debouncing */
+ break;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int max77650_charger_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct max77650_charger_data *chg = power_supply_get_drvdata(psy);
+ int rv, reg;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_STATUS:
+ rv = regmap_read(chg->map, MAX77650_REG_STAT_CHG_B, ®);
+ if (rv)
+ return rv;
+
+ if (MAX77650_CHARGER_CHG_CHARGING(reg)) {
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ break;
+ }
+
+ switch (MAX77650_CHG_DETAILS_BITS(reg)) {
+ case MAX77650_CHG_OFF:
+ case MAX77650_CHG_SUSP_PREQ_TIM_FAULT:
+ case MAX77650_CHG_SUSP_FAST_CHG_TIM_FAULT:
+ case MAX77650_CHG_SUSP_BATT_TEMP_FAULT:
+ val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ break;
+ case MAX77650_CHG_PREQ:
+ case MAX77650_CHG_ON_CURR:
+ case MAX77650_CHG_ON_CURR_JEITA:
+ case MAX77650_CHG_ON_VOLT:
+ case MAX77650_CHG_ON_VOLT_JEITA:
+ case MAX77650_CHG_ON_TOPOFF:
+ case MAX77650_CHG_ON_TOPOFF_JEITA:
+ val->intval = POWER_SUPPLY_STATUS_CHARGING;
+ break;
+ case MAX77650_CHG_DONE:
+ val->intval = POWER_SUPPLY_STATUS_FULL;
+ break;
+ default:
+ val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+ }
+ break;
+ case POWER_SUPPLY_PROP_ONLINE:
+ rv = regmap_read(chg->map, MAX77650_REG_STAT_CHG_B, ®);
+ if (rv)
+ return rv;
+
+ val->intval = MAX77650_CHARGER_CHG_CHARGING(reg);
+ break;
+ case POWER_SUPPLY_PROP_CHARGE_TYPE:
+ rv = regmap_read(chg->map, MAX77650_REG_STAT_CHG_B, ®);
+ if (rv)
+ return rv;
+
+ if (!MAX77650_CHARGER_CHG_CHARGING(reg)) {
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
+ break;
+ }
+
+ switch (MAX77650_CHG_DETAILS_BITS(reg)) {
+ case MAX77650_CHG_PREQ:
+ case MAX77650_CHG_ON_CURR:
+ case MAX77650_CHG_ON_CURR_JEITA:
+ case MAX77650_CHG_ON_VOLT:
+ case MAX77650_CHG_ON_VOLT_JEITA:
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
+ break;
+ case MAX77650_CHG_ON_TOPOFF:
+ case MAX77650_CHG_ON_TOPOFF_JEITA:
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+ break;
+ default:
+ val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+ }
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct power_supply_desc max77650_battery_desc = {
+ .name = "max77650",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .get_property = max77650_charger_get_property,
+ .properties = max77650_charger_properties,
+ .num_properties = ARRAY_SIZE(max77650_charger_properties),
+};
+
+static int max77650_charger_probe(struct platform_device *pdev)
+{
+ struct power_supply_config pscfg = {};
+ struct max77650_charger_data *chg;
+ struct power_supply *battery;
+ struct device *dev, *parent;
+ int rv, chg_irq, chgin_irq;
+ unsigned int prop;
+
+ dev = &pdev->dev;
+ parent = dev->parent;
+
+ chg = devm_kzalloc(dev, sizeof(*chg), GFP_KERNEL);
+ if (!chg)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, chg);
+
+ chg->map = dev_get_regmap(parent, NULL);
+ if (!chg->map)
+ return -ENODEV;
+
+ chg->dev = dev;
+
+ pscfg.of_node = dev->of_node;
+ pscfg.drv_data = chg;
+
+ chg_irq = platform_get_irq_byname(pdev, "CHG");
+ if (chg_irq < 0)
+ return chg_irq;
+
+ chgin_irq = platform_get_irq_byname(pdev, "CHGIN");
+ if (chgin_irq < 0)
+ return chgin_irq;
+
+ rv = devm_request_any_context_irq(dev, chg_irq,
+ max77650_charger_check_status,
+ IRQF_ONESHOT, "chg", chg);
+ if (rv < 0)
+ return rv;
+
+ rv = devm_request_any_context_irq(dev, chgin_irq,
+ max77650_charger_check_status,
+ IRQF_ONESHOT, "chgin", chg);
+ if (rv < 0)
+ return rv;
+
+ battery = devm_power_supply_register(dev,
+ &max77650_battery_desc, &pscfg);
+ if (IS_ERR(battery))
+ return PTR_ERR(battery);
+
+ rv = of_property_read_u32(dev->of_node, "min-microvolt", &prop);
+ if (rv == 0) {
+ rv = max77650_charger_set_vchgin_min(chg, prop);
+ if (rv)
+ return rv;
+ }
+
+ rv = of_property_read_u32(dev->of_node, "curr-lim-microamp", &prop);
+ if (rv == 0) {
+ rv = max77650_charger_set_ichgin_lim(chg, prop);
+ if (rv)
+ return rv;
+ }
+
+ return max77650_charger_enable(chg);
+}
+
+static int max77650_charger_remove(struct platform_device *pdev)
+{
+ struct max77650_charger_data *chg = platform_get_drvdata(pdev);
+
+ return max77650_charger_disable(chg);
+}
+
+static struct platform_driver max77650_charger_driver = {
+ .driver = {
+ .name = "max77650-charger",
+ },
+ .probe = max77650_charger_probe,
+ .remove = max77650_charger_remove,
+};
+module_platform_driver(max77650_charger_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 charger driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 06/11] mfd: max77650: new core mfd driver
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the core mfd driver for max77650 PMIC. We define five sub-devices
for which the drivers will be added in subsequent patches.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
drivers/mfd/Kconfig | 14 +++
drivers/mfd/Makefile | 1 +
drivers/mfd/max77650.c | 234 +++++++++++++++++++++++++++++++++++
include/linux/mfd/max77650.h | 59 +++++++++
4 files changed, 308 insertions(+)
create mode 100644 drivers/mfd/max77650.c
create mode 100644 include/linux/mfd/max77650.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 0ce2d8dfc5f1..ade04e124aa0 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -733,6 +733,20 @@ config MFD_MAX77620
provides common support for accessing the device; additional drivers
must be enabled in order to use the functionality of the device.
+config MFD_MAX77650
+ tristate "Maxim MAX77650/77651 PMIC Support"
+ depends on I2C
+ depends on OF || COMPILE_TEST
+ select MFD_CORE
+ select REGMAP_I2C
+ help
+ Say Y here to add support for Maxim Semiconductor MAX77650 and
+ MAX77651 Power Management ICs. This is the core multifunction
+ driver for interacting with the device. The module name is
+ 'max77650'. Additional drivers can be enabled in order to use
+ the following functionalities of the device: GPIO, regulator,
+ charger, LED, onkey.
+
config MFD_MAX77686
tristate "Maxim Semiconductor MAX77686/802 PMIC Support"
depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index b4569ed7f3f3..5727d099c16f 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -155,6 +155,7 @@ obj-$(CONFIG_MFD_DA9150) += da9150-core.o
obj-$(CONFIG_MFD_MAX14577) += max14577.o
obj-$(CONFIG_MFD_MAX77620) += max77620.o
+obj-$(CONFIG_MFD_MAX77650) += max77650.o
obj-$(CONFIG_MFD_MAX77686) += max77686.o
obj-$(CONFIG_MFD_MAX77693) += max77693.o
obj-$(CONFIG_MFD_MAX77843) += max77843.o
diff --git a/drivers/mfd/max77650.c b/drivers/mfd/max77650.c
new file mode 100644
index 000000000000..7a6c0a5cf602
--- /dev/null
+++ b/drivers/mfd/max77650.c
@@ -0,0 +1,234 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2018 BayLibre SAS
+// Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+//
+// Core MFD driver for MAXIM 77650/77651 charger/power-supply.
+// Programming manual: https://pdfserv.maximintegrated.com/en/an/AN6428.pdf
+
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/max77650.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+
+#define MAX77650_INT_GPI_F_MSK BIT(0)
+#define MAX77650_INT_GPI_R_MSK BIT(1)
+#define MAX77650_INT_GPI_MSK \
+ (MAX77650_INT_GPI_F_MSK | MAX77650_INT_GPI_R_MSK)
+#define MAX77650_INT_nEN_F_MSK BIT(2)
+#define MAX77650_INT_nEN_R_MSK BIT(3)
+#define MAX77650_INT_TJAL1_R_MSK BIT(4)
+#define MAX77650_INT_TJAL2_R_MSK BIT(5)
+#define MAX77650_INT_DOD_R_MSK BIT(6)
+
+#define MAX77650_INT_THM_MSK BIT(0)
+#define MAX77650_INT_CHG_MSK BIT(1)
+#define MAX77650_INT_CHGIN_MSK BIT(2)
+#define MAX77650_INT_TJ_REG_MSK BIT(3)
+#define MAX77650_INT_CHGIN_CTRL_MSK BIT(4)
+#define MAX77650_INT_SYS_CTRL_MSK BIT(5)
+#define MAX77650_INT_SYS_CNFG_MSK BIT(6)
+
+#define MAX77650_INT_GLBL_OFFSET 0
+#define MAX77650_INT_CHG_OFFSET 1
+
+#define MAX77650_SBIA_LPM_MASK BIT(5)
+#define MAX77650_SBIA_LPM_DISABLED 0x00
+
+enum {
+ MAX77650_INT_GPI,
+ MAX77650_INT_nEN_F,
+ MAX77650_INT_nEN_R,
+ MAX77650_INT_TJAL1_R,
+ MAX77650_INT_TJAL2_R,
+ MAX77650_INT_DOD_R,
+ MAX77650_INT_THM,
+ MAX77650_INT_CHG,
+ MAX77650_INT_CHGIN,
+ MAX77650_INT_TJ_REG,
+ MAX77650_INT_CHGIN_CTRL,
+ MAX77650_INT_SYS_CTRL,
+ MAX77650_INT_SYS_CNFG,
+};
+
+static const struct resource max77650_charger_resources[] = {
+ DEFINE_RES_IRQ_NAMED(MAX77650_INT_CHG, "CHG"),
+ DEFINE_RES_IRQ_NAMED(MAX77650_INT_CHGIN, "CHGIN"),
+};
+
+static const struct resource max77650_gpio_resources[] = {
+ DEFINE_RES_IRQ_NAMED(MAX77650_INT_GPI, "GPI"),
+};
+
+static const struct resource max77650_onkey_resources[] = {
+ DEFINE_RES_IRQ_NAMED(MAX77650_INT_nEN_F, "nEN_F"),
+ DEFINE_RES_IRQ_NAMED(MAX77650_INT_nEN_R, "nEN_R"),
+};
+
+static const struct mfd_cell max77650_cells[] = {
+ {
+ .name = "max77650-regulator",
+ .of_compatible = "maxim,max77650-regulator",
+ },
+ {
+ .name = "max77650-charger",
+ .of_compatible = "maxim,max77650-charger",
+ .resources = max77650_charger_resources,
+ .num_resources = ARRAY_SIZE(max77650_charger_resources),
+ },
+ {
+ .name = "max77650-gpio",
+ .of_compatible = "maxim,max77650-gpio",
+ .resources = max77650_gpio_resources,
+ .num_resources = ARRAY_SIZE(max77650_gpio_resources),
+ },
+ {
+ .name = "max77650-led",
+ .of_compatible = "maxim,max77650-led",
+ },
+ {
+ .name = "max77650-onkey",
+ .of_compatible = "maxim,max77650-onkey",
+ .resources = max77650_onkey_resources,
+ .num_resources = ARRAY_SIZE(max77650_onkey_resources),
+ },
+};
+
+static const struct regmap_irq max77650_irqs[] = {
+ [MAX77650_INT_GPI] = {
+ .reg_offset = MAX77650_INT_GLBL_OFFSET,
+ .mask = MAX77650_INT_GPI_MSK,
+ .type = {
+ .type_falling_val = MAX77650_INT_GPI_F_MSK,
+ .type_rising_val = MAX77650_INT_GPI_R_MSK,
+ .types_supported = IRQ_TYPE_EDGE_BOTH,
+ },
+ },
+ REGMAP_IRQ_REG(MAX77650_INT_nEN_F,
+ MAX77650_INT_GLBL_OFFSET, MAX77650_INT_nEN_F_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_nEN_R,
+ MAX77650_INT_GLBL_OFFSET, MAX77650_INT_nEN_R_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_TJAL1_R,
+ MAX77650_INT_GLBL_OFFSET, MAX77650_INT_TJAL1_R_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_TJAL2_R,
+ MAX77650_INT_GLBL_OFFSET, MAX77650_INT_TJAL2_R_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_DOD_R,
+ MAX77650_INT_GLBL_OFFSET, MAX77650_INT_DOD_R_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_THM,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_THM_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_CHG,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHG_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_CHGIN,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHGIN_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_TJ_REG,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_TJ_REG_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_CHGIN_CTRL,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_CHGIN_CTRL_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_SYS_CTRL,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_SYS_CTRL_MSK),
+ REGMAP_IRQ_REG(MAX77650_INT_SYS_CNFG,
+ MAX77650_INT_CHG_OFFSET, MAX77650_INT_SYS_CNFG_MSK),
+};
+
+static const struct regmap_irq_chip max77650_irq_chip = {
+ .name = "max77650-irq",
+ .irqs = max77650_irqs,
+ .num_irqs = ARRAY_SIZE(max77650_irqs),
+ .num_regs = 2,
+ .status_base = MAX77650_REG_INT_GLBL,
+ .mask_base = MAX77650_REG_INTM_GLBL,
+ .type_in_mask = true,
+ .type_invert = true,
+ .init_ack_masked = true,
+ .clear_on_unmask = true,
+};
+
+static const struct regmap_config max77650_regmap_config = {
+ .name = "max77650",
+ .reg_bits = 8,
+ .val_bits = 8,
+};
+
+static int max77650_i2c_probe(struct i2c_client *i2c)
+{
+ struct regmap_irq_chip_data *irq_data;
+ struct device *dev = &i2c->dev;
+ struct irq_domain *domain;
+ struct regmap *map;
+ unsigned int val;
+ int rv;
+
+ map = devm_regmap_init_i2c(i2c, &max77650_regmap_config);
+ if (IS_ERR(map)) {
+ dev_err(dev, "unable to initialize i2c regmap\n");
+ return PTR_ERR(map);
+ }
+
+ rv = regmap_read(map, MAX77650_REG_CID, &val);
+ if (rv) {
+ dev_err(dev, "unable to read the CID from device\n");
+ return rv;
+ }
+
+ switch (MAX77650_CID_BITS(val)) {
+ case MAX77650_CID_77650A:
+ case MAX77650_CID_77650C:
+ case MAX77650_CID_77651A:
+ case MAX77650_CID_77651B:
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ /*
+ * This IC has a low-power mode which reduces the quiescent current
+ * consumption to ~5.6uA but is only suitable for systems consuming
+ * less than ~2mA. Since this is not likely the case even on
+ * linux-based wearables - keep the chip in normal power mode.
+ */
+ rv = regmap_update_bits(map,
+ MAX77650_REG_CNFG_GLBL,
+ MAX77650_SBIA_LPM_MASK,
+ MAX77650_SBIA_LPM_DISABLED);
+ if (rv) {
+ dev_err(dev, "unable to change the power mode\n");
+ return rv;
+ }
+
+ rv = devm_regmap_add_irq_chip(dev, map, i2c->irq,
+ IRQF_ONESHOT | IRQF_SHARED, 0,
+ &max77650_irq_chip, &irq_data);
+ if (rv) {
+ dev_err(dev, "unable to add the regmap irq chip\n");
+ return rv;
+ }
+
+ domain = regmap_irq_get_domain(irq_data);
+
+ return devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
+ max77650_cells, ARRAY_SIZE(max77650_cells),
+ NULL, 0, domain);
+}
+
+static const struct of_device_id max77650_of_match[] = {
+ { .compatible = "maxim,max77650" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, max77650_of_match);
+
+static struct i2c_driver max77650_i2c_driver = {
+ .driver = {
+ .name = "max77650",
+ .of_match_table = of_match_ptr(max77650_of_match),
+ },
+ .probe_new = max77650_i2c_probe,
+};
+module_i2c_driver(max77650_i2c_driver);
+
+MODULE_DESCRIPTION("MAXIM 77650/77651 multi-function core driver");
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/max77650.h b/include/linux/mfd/max77650.h
new file mode 100644
index 000000000000..c809e211a8cd
--- /dev/null
+++ b/include/linux/mfd/max77650.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 BayLibre SAS
+ * Author: Bartosz Golaszewski <bgolaszewski@baylibre.com>
+ *
+ * Common definitions for MAXIM 77650/77651 charger/power-supply.
+ */
+
+#ifndef MAX77650_H
+#define MAX77650_H
+
+#include <linux/bits.h>
+
+#define MAX77650_REG_INT_GLBL 0x00
+#define MAX77650_REG_INT_CHG 0x01
+#define MAX77650_REG_STAT_CHG_A 0x02
+#define MAX77650_REG_STAT_CHG_B 0x03
+#define MAX77650_REG_ERCFLAG 0x04
+#define MAX77650_REG_STAT_GLBL 0x05
+#define MAX77650_REG_INTM_GLBL 0x06
+#define MAX77650_REG_INTM_CHG 0x07
+#define MAX77650_REG_CNFG_GLBL 0x10
+#define MAX77650_REG_CID 0x11
+#define MAX77650_REG_CNFG_GPIO 0x12
+#define MAX77650_REG_CNFG_CHG_A 0x18
+#define MAX77650_REG_CNFG_CHG_B 0x19
+#define MAX77650_REG_CNFG_CHG_C 0x1a
+#define MAX77650_REG_CNFG_CHG_D 0x1b
+#define MAX77650_REG_CNFG_CHG_E 0x1c
+#define MAX77650_REG_CNFG_CHG_F 0x1d
+#define MAX77650_REG_CNFG_CHG_G 0x1e
+#define MAX77650_REG_CNFG_CHG_H 0x1f
+#define MAX77650_REG_CNFG_CHG_I 0x20
+#define MAX77650_REG_CNFG_SBB_TOP 0x28
+#define MAX77650_REG_CNFG_SBB0_A 0x29
+#define MAX77650_REG_CNFG_SBB0_B 0x2a
+#define MAX77650_REG_CNFG_SBB1_A 0x2b
+#define MAX77650_REG_CNFG_SBB1_B 0x2c
+#define MAX77650_REG_CNFG_SBB2_A 0x2d
+#define MAX77650_REG_CNFG_SBB2_B 0x2e
+#define MAX77650_REG_CNFG_LDO_A 0x38
+#define MAX77650_REG_CNFG_LDO_B 0x39
+#define MAX77650_REG_CNFG_LED0_A 0x40
+#define MAX77650_REG_CNFG_LED1_A 0x41
+#define MAX77650_REG_CNFG_LED2_A 0x42
+#define MAX77650_REG_CNFG_LED0_B 0x43
+#define MAX77650_REG_CNFG_LED1_B 0x44
+#define MAX77650_REG_CNFG_LED2_B 0x45
+#define MAX77650_REG_CNFG_LED_TOP 0x46
+
+#define MAX77650_CID_MASK GENMASK(3, 0)
+#define MAX77650_CID_BITS(_reg) (_reg & MAX77650_CID_MASK)
+
+#define MAX77650_CID_77650A 0x03
+#define MAX77650_CID_77650C 0x0a
+#define MAX77650_CID_77651A 0x06
+#define MAX77650_CID_77651B 0x08
+
+#endif /* MAX77650_H */
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 05/11] mfd: core: document mfd_add_devices()
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add a kernel doc for mfd_add_devices().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
drivers/mfd/mfd-core.c | 14 ++++++++++++++
1 file changed, 14 insertions(+)
diff --git a/drivers/mfd/mfd-core.c b/drivers/mfd/mfd-core.c
index 94e3f32ce935..0898a8db1747 100644
--- a/drivers/mfd/mfd-core.c
+++ b/drivers/mfd/mfd-core.c
@@ -269,6 +269,20 @@ static int mfd_add_device(struct device *parent, int id,
return ret;
}
+/**
+ * mfd_add_devices - register a set of child devices
+ *
+ * @parent: Parent device for all sub-nodes.
+ * @id: Platform device id. If >= 0, each sub-device will have its cell_id
+ * added to this number and use it as the platform device id.
+ * @cells: Array of mfd cells describing sub-devices.
+ * @n_devs: Number of sub-devices to register.
+ * @mem_base: Parent register range resource for sub-devices.
+ * @irq_base: Base of the range of virtual interrupt numbers allocated for
+ * this MFD device. Unused if @domain is specified.
+ * @domain: Interrupt domain used to create mappings for HW interrupt numbers
+ * specificed in sub-devices' IRQ resources.
+ */
int mfd_add_devices(struct device *parent, int id,
const struct mfd_cell *cells, int n_devs,
struct resource *mem_base,
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 04/11] dt-bindings: input: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski, Rob Herring
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the DT binding document for the onkey module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/input/max77650-onkey.txt | 26 +++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/max77650-onkey.txt
diff --git a/Documentation/devicetree/bindings/input/max77650-onkey.txt b/Documentation/devicetree/bindings/input/max77650-onkey.txt
new file mode 100644
index 000000000000..477dc74f452a
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/max77650-onkey.txt
@@ -0,0 +1,26 @@
+Onkey driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The onkey controller is represented as a sub-node of the PMIC node on
+the device tree.
+
+Required properties:
+--------------------
+- compatible: Must be "maxim,max77650-onkey".
+
+Optional properties:
+- linux,code: The key-code to be reported when the key is pressed.
+ Defaults to KEY_POWER.
+- maxim,onkey-slide: The system's button is a slide switch, not the default
+ push button.
+
+Example:
+--------
+
+ onkey {
+ compatible = "maxim,max77650-onkey";
+ linux,code = <KEY_END>;
+ maxim,onkey-slide;
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 03/11] dt-bindings: leds: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski, Rob Herring
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the DT binding document for the LEDs module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/leds/leds-max77650.txt | 57 +++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/leds-max77650.txt
diff --git a/Documentation/devicetree/bindings/leds/leds-max77650.txt b/Documentation/devicetree/bindings/leds/leds-max77650.txt
new file mode 100644
index 000000000000..3a67115cc1da
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-max77650.txt
@@ -0,0 +1,57 @@
+LED driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The LED controller is represented as a sub-node of the PMIC node on
+the device tree.
+
+This device has three current sinks.
+
+Required properties:
+--------------------
+- compatible: Must be "maxim,max77650-led"
+- #address-cells: Must be <1>.
+- #size-cells: Must be <0>.
+
+Each LED is represented as a sub-node of the LED-controller node. Up to
+three sub-nodes can be defined.
+
+Required properties of the sub-node:
+------------------------------------
+
+- reg: Must be <0>, <1> or <2>.
+
+Optional properties of the sub-node:
+------------------------------------
+
+- label: See Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger: See Documentation/devicetree/bindings/leds/common.txt
+
+For more details, please refer to the generic GPIO DT binding document
+<devicetree/bindings/gpio/gpio.txt>.
+
+Example:
+--------
+
+ leds {
+ compatible = "maxim,max77650-led";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "blue:usr0";
+ };
+
+ led@1 {
+ reg = <1>;
+ label = "red:usr1";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led@2 {
+ reg = <2>;
+ label = "green:usr2";
+ };
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 02/11] dt-bindings: power: supply: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
.../power/supply/max77650-charger.txt | 27 +++++++++++++++++++
1 file changed, 27 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/max77650-charger.txt
diff --git a/Documentation/devicetree/bindings/power/supply/max77650-charger.txt b/Documentation/devicetree/bindings/power/supply/max77650-charger.txt
new file mode 100644
index 000000000000..d25c95369616
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/max77650-charger.txt
@@ -0,0 +1,27 @@
+Battery charger driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The charger is represented as a sub-node of the PMIC node on the device tree.
+
+Required properties:
+--------------------
+- compatible: Must be "maxim,max77650-charger"
+
+Optional properties:
+--------------------
+- min-microvolt: Minimum CHGIN regulation voltage (in microvolts). Must be
+ one of: 4000000, 4100000, 4200000, 4300000, 4400000,
+ 4500000, 4600000, 4700000.
+- curr-lim-microamp: CHGIN input current limit (in microamps). Must be one of:
+ 95000, 190000, 285000, 380000, 475000.
+
+Example:
+--------
+
+ charger {
+ compatible = "maxim,max77650-charger";
+ min-microvolt = <4200000>;
+ curr-lim-microamp = <285000>;
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 01/11] dt-bindings: mfd: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski, Rob Herring
In-Reply-To: <20190318174228.18194-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add a DT binding document for max77650 ultra-low power PMIC. This
describes the core mfd device and the GPIO module.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/mfd/max77650.txt | 46 +++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/max77650.txt
diff --git a/Documentation/devicetree/bindings/mfd/max77650.txt b/Documentation/devicetree/bindings/mfd/max77650.txt
new file mode 100644
index 000000000000..b529d8d19335
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77650.txt
@@ -0,0 +1,46 @@
+MAX77650 ultra low-power PMIC from Maxim Integrated.
+
+Required properties:
+-------------------
+- compatible: Must be "maxim,max77650"
+- reg: I2C device address.
+- interrupts: The interrupt on the parent the controller is
+ connected to.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Must be <2>.
+
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Must be <2>. The first cell is the pin number and
+ the second cell is used to specify the gpio active
+ state.
+
+Optional properties:
+--------------------
+gpio-line-names: Single string containing the name of the GPIO line.
+
+The GPIO-controller module is represented as part of the top-level PMIC
+node. The device exposes a single GPIO line.
+
+For device-tree bindings of other sub-modules (regulator, power supply,
+LEDs and onkey) refer to the binding documents under the respective
+sub-system directories.
+
+For more details on GPIO bindings, please refer to the generic GPIO DT
+binding document <devicetree/bindings/gpio/gpio.txt>.
+
+Example:
+--------
+
+ pmic@48 {
+ compatible = "maxim,max77650";
+ reg = <0x48>;
+
+ interrupt-controller;
+ interrupt-parent = <&gpio2>;
+ #interrupt-cells = <2>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "max77650-charger";
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 00/11] mfd: add support for max77650 PMIC
From: Bartosz Golaszewski @ 2019-03-18 17:42 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This series missed the last merge window so resending rebased on top
of v5.1-rc1 with no functional changes.
---
This series adds support for max77650 ultra low-power PMIC. It provides
the core mfd driver and a set of five sub-drivers for the regulator,
power supply, gpio, leds and input subsystems.
Patches 1-4 add the DT binding documents. Patch 5 documents mfd_add_devices().
Patches 6-10 add all drivers. Last patch adds a MAINTAINERS entry for this
device.
The regulator part is already upstream.
v1 -> v2:
=========
General:
- use C++ style comments for the SPDX license identifier and the
copyright header
- s/MODULE_LICENSE("GPL")/MODULE_LICENSE("GPL v2")/
- lookup the virtual interrupt numbers in the MFD driver, setup
resources for child devices and use platform_get_irq_byname()
in sub-drivers
- picked up review tags
- use devm_request_any_context_irq() for interrupt requests
LEDs:
- changed the max77650_leds_ prefix to max77650_led_
- drop the max77650_leds structure as the only field it held was the
regmap pointer, move said pointer to struct max77650_led
- change the driver name to "max77650-led"
- drop the last return value check and return the result of
regmap_write() directly
- change the labeling scheme to one consistent with other LED drivers
ONKEY:
- drop the key reporting helper and call the input functions directly
from interrupt handlers
- rename the rv local variable to error
- drop parent device asignment
Regulator:
- drop the unnecessary init_data lookup from the driver code
- drop unnecessary include
Charger:
- disable the charger on driver remove
- change the power supply type to POWER_SUPPLY_TYPE_USB
GPIO:
- drop interrupt support until we have correct implementation of hierarchical
irqs in gpiolib
v2 -> v3:
=========
General:
- dropped regulator patches as they're already in Mark Brown's branch
LED:
- fix the compatible string in the DT binding example
- use the max_brightness property
- use a common prefix ("MAX77650_LED") for all defines in the driver
MFD:
- add the MODULE_DEVICE_TABLE()
- add a sentinel to the of_device_id array
- constify the pointers to irq names
- use an enum instead of defines for interrupt indexes
v3 -> v4:
=========
GPIO:
- as discussed with Linus Walleij: the gpio-controller is now part of
the core mfd module (we don't spawn a sub-node anymore), the binding
document for GPIO has been dropped, the GPIO properties have been
defined in the binding document for the mfd core, the interrupt
functionality has been reintroduced with the irq directly passed from
the mfd part
- due to the above changes the Reviewed-by tag from Linus was dropped
v4 -> v5:
=========
General:
- add a patch documenting mfd_add_devices()
MFD:
- pass the regmap irq_chip irq domain to mfd over mfd_add_devices so that
the hw interrupts from resources can be correctly mapped to virtual irqs
- remove the enum listing cell indexes
- extend Kconfig help
- add a link to the programming manual
- use REGMAP_IRQ_REG() for regmap interrupts (except for GPI which has
is composed of two hw interrupts for rising and falling edge)
- add error messages in probe
- use PLATFORM_DEVID_NONE constant in devm_mfd_add_devices()
- set irq_base to 0 in regmap_add_irq_chip() as other users to, it's only
relevant if it's > 0
Charger:
- use non-maxim specific property names for minimum input voltage and current
limit
- code shrink by using the enable/disable charger helpers everywhere
- use more descriptive names for constants
Onkey:
- use EV_SW event type for slide mode
LED:
- remove stray " from Kconfig help
v5 -> v6:
=========
MFD:
- remove stray spaces in the binding document
- rename the example dt node
- remove unnecessary interrupt-parent property from the bindings
LED:
- add a missing dependency on LEDS_CLASS to Kconfig
Onkey:
- use boolean for the slide button property
Charger:
- fix the property names in DT example
- make constants even more readable
Bartosz Golaszewski (11):
dt-bindings: mfd: add DT bindings for max77650
dt-bindings: power: supply: add DT bindings for max77650
dt-bindings: leds: add DT bindings for max77650
dt-bindings: input: add DT bindings for max77650
mfd: core: document mfd_add_devices()
mfd: max77650: new core mfd driver
power: supply: max77650: add support for battery charger
gpio: max77650: add GPIO support
leds: max77650: add LEDs support
input: max77650: add onkey support
MAINTAINERS: add an entry for max77650 mfd driver
.../bindings/input/max77650-onkey.txt | 26 ++
.../bindings/leds/leds-max77650.txt | 57 +++
.../devicetree/bindings/mfd/max77650.txt | 46 +++
.../power/supply/max77650-charger.txt | 27 ++
MAINTAINERS | 14 +
drivers/gpio/Kconfig | 7 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-max77650.c | 190 +++++++++
drivers/input/misc/Kconfig | 9 +
drivers/input/misc/Makefile | 1 +
drivers/input/misc/max77650-onkey.c | 121 ++++++
drivers/leds/Kconfig | 6 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-max77650.c | 147 +++++++
drivers/mfd/Kconfig | 14 +
drivers/mfd/Makefile | 1 +
drivers/mfd/max77650.c | 234 +++++++++++
drivers/mfd/mfd-core.c | 14 +
drivers/power/supply/Kconfig | 7 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/max77650-charger.c | 366 ++++++++++++++++++
include/linux/mfd/max77650.h | 59 +++
22 files changed, 1349 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/max77650-onkey.txt
create mode 100644 Documentation/devicetree/bindings/leds/leds-max77650.txt
create mode 100644 Documentation/devicetree/bindings/mfd/max77650.txt
create mode 100644 Documentation/devicetree/bindings/power/supply/max77650-charger.txt
create mode 100644 drivers/gpio/gpio-max77650.c
create mode 100644 drivers/input/misc/max77650-onkey.c
create mode 100644 drivers/leds/leds-max77650.c
create mode 100644 drivers/mfd/max77650.c
create mode 100644 drivers/power/supply/max77650-charger.c
create mode 100644 include/linux/mfd/max77650.h
--
2.20.1
^ permalink raw reply
* [RESEND PATCH v6 03/11] dt-bindings: leds: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:40 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski, Rob Herring
In-Reply-To: <20190318174040.17899-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the DT binding document for the LEDs module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/leds/leds-max77650.txt | 57 +++++++++++++++++++
1 file changed, 57 insertions(+)
create mode 100644 Documentation/devicetree/bindings/leds/leds-max77650.txt
diff --git a/Documentation/devicetree/bindings/leds/leds-max77650.txt b/Documentation/devicetree/bindings/leds/leds-max77650.txt
new file mode 100644
index 000000000000..3a67115cc1da
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/leds-max77650.txt
@@ -0,0 +1,57 @@
+LED driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The LED controller is represented as a sub-node of the PMIC node on
+the device tree.
+
+This device has three current sinks.
+
+Required properties:
+--------------------
+- compatible: Must be "maxim,max77650-led"
+- #address-cells: Must be <1>.
+- #size-cells: Must be <0>.
+
+Each LED is represented as a sub-node of the LED-controller node. Up to
+three sub-nodes can be defined.
+
+Required properties of the sub-node:
+------------------------------------
+
+- reg: Must be <0>, <1> or <2>.
+
+Optional properties of the sub-node:
+------------------------------------
+
+- label: See Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger: See Documentation/devicetree/bindings/leds/common.txt
+
+For more details, please refer to the generic GPIO DT binding document
+<devicetree/bindings/gpio/gpio.txt>.
+
+Example:
+--------
+
+ leds {
+ compatible = "maxim,max77650-led";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ label = "blue:usr0";
+ };
+
+ led@1 {
+ reg = <1>;
+ label = "red:usr1";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led@2 {
+ reg = <2>;
+ label = "green:usr2";
+ };
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 02/11] dt-bindings: power: supply: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:40 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
In-Reply-To: <20190318174040.17899-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the DT binding document for the battery charger module of max77650.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
.../power/supply/max77650-charger.txt | 27 +++++++++++++++++++
1 file changed, 27 insertions(+)
create mode 100644 Documentation/devicetree/bindings/power/supply/max77650-charger.txt
diff --git a/Documentation/devicetree/bindings/power/supply/max77650-charger.txt b/Documentation/devicetree/bindings/power/supply/max77650-charger.txt
new file mode 100644
index 000000000000..d25c95369616
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/max77650-charger.txt
@@ -0,0 +1,27 @@
+Battery charger driver for MAX77650 PMIC from Maxim Integrated.
+
+This module is part of the MAX77650 MFD device. For more details
+see Documentation/devicetree/bindings/mfd/max77650.txt.
+
+The charger is represented as a sub-node of the PMIC node on the device tree.
+
+Required properties:
+--------------------
+- compatible: Must be "maxim,max77650-charger"
+
+Optional properties:
+--------------------
+- min-microvolt: Minimum CHGIN regulation voltage (in microvolts). Must be
+ one of: 4000000, 4100000, 4200000, 4300000, 4400000,
+ 4500000, 4600000, 4700000.
+- curr-lim-microamp: CHGIN input current limit (in microamps). Must be one of:
+ 95000, 190000, 285000, 380000, 475000.
+
+Example:
+--------
+
+ charger {
+ compatible = "maxim,max77650-charger";
+ min-microvolt = <4200000>;
+ curr-lim-microamp = <285000>;
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 01/11] dt-bindings: mfd: add DT bindings for max77650
From: Bartosz Golaszewski @ 2019-03-18 17:40 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski, Rob Herring
In-Reply-To: <20190318174040.17899-1-brgl@bgdev.pl>
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add a DT binding document for max77650 ultra-low power PMIC. This
describes the core mfd device and the GPIO module.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/mfd/max77650.txt | 46 +++++++++++++++++++
1 file changed, 46 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/max77650.txt
diff --git a/Documentation/devicetree/bindings/mfd/max77650.txt b/Documentation/devicetree/bindings/mfd/max77650.txt
new file mode 100644
index 000000000000..b529d8d19335
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77650.txt
@@ -0,0 +1,46 @@
+MAX77650 ultra low-power PMIC from Maxim Integrated.
+
+Required properties:
+-------------------
+- compatible: Must be "maxim,max77650"
+- reg: I2C device address.
+- interrupts: The interrupt on the parent the controller is
+ connected to.
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells: Must be <2>.
+
+- gpio-controller: Marks the device node as a gpio controller.
+- #gpio-cells: Must be <2>. The first cell is the pin number and
+ the second cell is used to specify the gpio active
+ state.
+
+Optional properties:
+--------------------
+gpio-line-names: Single string containing the name of the GPIO line.
+
+The GPIO-controller module is represented as part of the top-level PMIC
+node. The device exposes a single GPIO line.
+
+For device-tree bindings of other sub-modules (regulator, power supply,
+LEDs and onkey) refer to the binding documents under the respective
+sub-system directories.
+
+For more details on GPIO bindings, please refer to the generic GPIO DT
+binding document <devicetree/bindings/gpio/gpio.txt>.
+
+Example:
+--------
+
+ pmic@48 {
+ compatible = "maxim,max77650";
+ reg = <0x48>;
+
+ interrupt-controller;
+ interrupt-parent = <&gpio2>;
+ #interrupt-cells = <2>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "max77650-charger";
+ };
--
2.20.1
^ permalink raw reply related
* [RESEND PATCH v6 00/11] mfd: add support for max77650 PMIC
From: Bartosz Golaszewski @ 2019-03-18 17:40 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Linus Walleij, Dmitry Torokhov,
Jacek Anaszewski, Pavel Machek, Lee Jones, Sebastian Reichel,
Liam Girdwood, Greg Kroah-Hartman
Cc: linux-kernel, linux-gpio, devicetree, linux-input, linux-leds,
linux-pm, Bartosz Golaszewski
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This series missed the last merge window so resending rebased on top
of v5.1-rc1 with no functional changes.
---
This series adds support for max77650 ultra low-power PMIC. It provides
the core mfd driver and a set of five sub-drivers for the regulator,
power supply, gpio, leds and input subsystems.
Patches 1-4 add the DT binding documents. Patch 5 documents mfd_add_devices().
Patches 6-10 add all drivers. Last patch adds a MAINTAINERS entry for this
device.
The regulator part is already upstream.
v1 -> v2:
=========
General:
- use C++ style comments for the SPDX license identifier and the
copyright header
- s/MODULE_LICENSE("GPL")/MODULE_LICENSE("GPL v2")/
- lookup the virtual interrupt numbers in the MFD driver, setup
resources for child devices and use platform_get_irq_byname()
in sub-drivers
- picked up review tags
- use devm_request_any_context_irq() for interrupt requests
LEDs:
- changed the max77650_leds_ prefix to max77650_led_
- drop the max77650_leds structure as the only field it held was the
regmap pointer, move said pointer to struct max77650_led
- change the driver name to "max77650-led"
- drop the last return value check and return the result of
regmap_write() directly
- change the labeling scheme to one consistent with other LED drivers
ONKEY:
- drop the key reporting helper and call the input functions directly
from interrupt handlers
- rename the rv local variable to error
- drop parent device asignment
Regulator:
- drop the unnecessary init_data lookup from the driver code
- drop unnecessary include
Charger:
- disable the charger on driver remove
- change the power supply type to POWER_SUPPLY_TYPE_USB
GPIO:
- drop interrupt support until we have correct implementation of hierarchical
irqs in gpiolib
v2 -> v3:
=========
General:
- dropped regulator patches as they're already in Mark Brown's branch
LED:
- fix the compatible string in the DT binding example
- use the max_brightness property
- use a common prefix ("MAX77650_LED") for all defines in the driver
MFD:
- add the MODULE_DEVICE_TABLE()
- add a sentinel to the of_device_id array
- constify the pointers to irq names
- use an enum instead of defines for interrupt indexes
v3 -> v4:
=========
GPIO:
- as discussed with Linus Walleij: the gpio-controller is now part of
the core mfd module (we don't spawn a sub-node anymore), the binding
document for GPIO has been dropped, the GPIO properties have been
defined in the binding document for the mfd core, the interrupt
functionality has been reintroduced with the irq directly passed from
the mfd part
- due to the above changes the Reviewed-by tag from Linus was dropped
v4 -> v5:
=========
General:
- add a patch documenting mfd_add_devices()
MFD:
- pass the regmap irq_chip irq domain to mfd over mfd_add_devices so that
the hw interrupts from resources can be correctly mapped to virtual irqs
- remove the enum listing cell indexes
- extend Kconfig help
- add a link to the programming manual
- use REGMAP_IRQ_REG() for regmap interrupts (except for GPI which has
is composed of two hw interrupts for rising and falling edge)
- add error messages in probe
- use PLATFORM_DEVID_NONE constant in devm_mfd_add_devices()
- set irq_base to 0 in regmap_add_irq_chip() as other users to, it's only
relevant if it's > 0
Charger:
- use non-maxim specific property names for minimum input voltage and current
limit
- code shrink by using the enable/disable charger helpers everywhere
- use more descriptive names for constants
Onkey:
- use EV_SW event type for slide mode
LED:
- remove stray " from Kconfig help
v5 -> v6:
=========
MFD:
- remove stray spaces in the binding document
- rename the example dt node
- remove unnecessary interrupt-parent property from the bindings
LED:
- add a missing dependency on LEDS_CLASS to Kconfig
Onkey:
- use boolean for the slide button property
Charger:
- fix the property names in DT example
- make constants even more readable
Bartosz Golaszewski (11):
dt-bindings: mfd: add DT bindings for max77650
dt-bindings: power: supply: add DT bindings for max77650
dt-bindings: leds: add DT bindings for max77650
dt-bindings: input: add DT bindings for max77650
mfd: core: document mfd_add_devices()
mfd: max77650: new core mfd driver
power: supply: max77650: add support for battery charger
gpio: max77650: add GPIO support
leds: max77650: add LEDs support
input: max77650: add onkey support
MAINTAINERS: add an entry for max77650 mfd driver
.../bindings/input/max77650-onkey.txt | 26 ++
.../bindings/leds/leds-max77650.txt | 57 +++
.../devicetree/bindings/mfd/max77650.txt | 46 +++
.../power/supply/max77650-charger.txt | 27 ++
MAINTAINERS | 14 +
drivers/gpio/Kconfig | 7 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-max77650.c | 190 +++++++++
drivers/input/misc/Kconfig | 9 +
drivers/input/misc/Makefile | 1 +
drivers/input/misc/max77650-onkey.c | 121 ++++++
drivers/leds/Kconfig | 6 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-max77650.c | 147 +++++++
drivers/mfd/Kconfig | 14 +
drivers/mfd/Makefile | 1 +
drivers/mfd/max77650.c | 234 +++++++++++
drivers/mfd/mfd-core.c | 14 +
drivers/power/supply/Kconfig | 7 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/max77650-charger.c | 366 ++++++++++++++++++
include/linux/mfd/max77650.h | 59 +++
22 files changed, 1349 insertions(+)
create mode 100644 Documentation/devicetree/bindings/input/max77650-onkey.txt
create mode 100644 Documentation/devicetree/bindings/leds/leds-max77650.txt
create mode 100644 Documentation/devicetree/bindings/mfd/max77650.txt
create mode 100644 Documentation/devicetree/bindings/power/supply/max77650-charger.txt
create mode 100644 drivers/gpio/gpio-max77650.c
create mode 100644 drivers/input/misc/max77650-onkey.c
create mode 100644 drivers/leds/leds-max77650.c
create mode 100644 drivers/mfd/max77650.c
create mode 100644 drivers/power/supply/max77650-charger.c
create mode 100644 include/linux/mfd/max77650.h
--
2.20.1
^ permalink raw reply
* RE: [PATCH 0/6] mfd: da9063: remove platform_data
From: Steve Twiss @ 2019-03-18 16:34 UTC (permalink / raw)
To: Mark Brown, Wolfram Sang
Cc: linux-kernel@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
Lee Jones, Support Opensource, linux-input@vger.kernel.org
In-Reply-To: <20190318154759.21978-1-wsa+renesas@sang-engineering.com>
Hi Mark,
On 18 March 2019 15:48, Wolfram Sang wrote:
> To: linux-kernel@vger.kernel.org
> Subject: [PATCH 0/6] mfd: da9063: remove platform_data
>
> When working with this driver while debugging something else, I noticed that
> there are no in-kernel users of platform_data anymore. Removing the support
> simplifies the code and gets rid of quite some lines. The biggest refactoring
> went to the regulator driver which could maybe benefit from more
> refactorization. However, there is no in-kernel user of that driver, so no
> testing. I left it at this stage. I think the changes are still at a level
> where review and build-testing will give enough confidence.
>
> Besides the regulator thing, it was tested on a Renesas Lager board (R-Car H2).
> No regressions encountered. buildbot was happy, too.
>
> The patches are based on v5.1-rc1. I'd vote for all of them going through the
> MFD tree. Looking forward to comments!
>
> Wolfram
My regulator tests are currently broken, so I'm looking into it.
I'll read-through and test these patches as soon as I've solved the regressions.
Regards,
Steve
^ permalink raw reply
* [PATCH 3/4] input: da9063_onkey: convert header to SPDX
From: Wolfram Sang @ 2019-03-18 15:57 UTC (permalink / raw)
To: linux-kernel
Cc: linux-renesas-soc, Lee Jones, Mark Brown, Support Opensource,
Wolfram Sang, Dmitry Torokhov, linux-input
In-Reply-To: <20190318155728.28365-1-wsa+renesas@sang-engineering.com>
Covnert the header of the source file to SPDX.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
drivers/input/misc/da9063_onkey.c | 11 +----------
1 file changed, 1 insertion(+), 10 deletions(-)
diff --git a/drivers/input/misc/da9063_onkey.c b/drivers/input/misc/da9063_onkey.c
index 3e9c353d82ef..7b8ae905a6fb 100644
--- a/drivers/input/misc/da9063_onkey.c
+++ b/drivers/input/misc/da9063_onkey.c
@@ -1,16 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0+
/*
* OnKey device driver for DA9063, DA9062 and DA9061 PMICs
* Copyright (C) 2015 Dialog Semiconductor Ltd.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
*/
#include <linux/module.h>
--
2.11.0
^ permalink raw reply related
* [PATCH 0/4] da9063: convert to SPDX
From: Wolfram Sang @ 2019-03-18 15:57 UTC (permalink / raw)
To: linux-kernel
Cc: linux-renesas-soc, Lee Jones, Mark Brown, Support Opensource,
Wolfram Sang, linux-input, linux-rtc
When working with this driver while debugging something else, I noticed a typo
in one of the file headers and decided that it could be converted to SPDX while
I am at it anyhow.
These patches were "tested" on a Renesas Lager board (R-Car H2). No regressions
encountered. buildbot was happy, too.
The patches are based on v5.1-rc1. I'd think they can be picked up per
subsystem but am also fine with everything going via MFD. There is no
dependency or merge conflict with my platform_data removal series which I sent
a few minutes ago.
Looking forward to comments!
Wolfram
Wolfram Sang (4):
mfd: da9063: convert headers to SPDX
regulator: da9063: convert header to SPDX
input: da9063_onkey: convert header to SPDX
rtc: da9063: convert header to SPDX
drivers/input/misc/da9063_onkey.c | 11 +----------
drivers/mfd/da9063-core.c | 8 ++------
drivers/mfd/da9063-i2c.c | 9 ++-------
drivers/mfd/da9063-irq.c | 9 ++-------
drivers/regulator/da9063-regulator.c | 8 +-------
drivers/rtc/rtc-da9063.c | 14 +++-----------
include/linux/mfd/da9063/core.h | 7 +------
include/linux/mfd/da9063/registers.h | 7 +------
8 files changed, 13 insertions(+), 60 deletions(-)
--
2.11.0
^ permalink raw reply
* [PATCH 2/6] input: da9063_onkey: remove platform_data support
From: Wolfram Sang @ 2019-03-18 15:47 UTC (permalink / raw)
To: linux-kernel
Cc: linux-renesas-soc, Lee Jones, Mark Brown, Support Opensource,
Wolfram Sang, Dmitry Torokhov, linux-input
In-Reply-To: <20190318154759.21978-1-wsa+renesas@sang-engineering.com>
There are no in-kernel users anymore, so remove this outdated interface.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
drivers/input/misc/da9063_onkey.c | 11 ++---------
1 file changed, 2 insertions(+), 9 deletions(-)
diff --git a/drivers/input/misc/da9063_onkey.c b/drivers/input/misc/da9063_onkey.c
index 3e9c353d82ef..e3a273c74123 100644
--- a/drivers/input/misc/da9063_onkey.c
+++ b/drivers/input/misc/da9063_onkey.c
@@ -22,7 +22,6 @@
#include <linux/regmap.h>
#include <linux/of.h>
#include <linux/mfd/da9063/core.h>
-#include <linux/mfd/da9063/pdata.h>
#include <linux/mfd/da9063/registers.h>
#include <linux/mfd/da9062/core.h>
#include <linux/mfd/da9062/registers.h>
@@ -201,8 +200,6 @@ static void da9063_cancel_poll(void *data)
static int da9063_onkey_probe(struct platform_device *pdev)
{
- struct da9063 *da9063 = dev_get_drvdata(pdev->dev.parent);
- struct da9063_pdata *pdata = dev_get_platdata(da9063->dev);
struct da9063_onkey *onkey;
const struct of_device_id *match;
int irq;
@@ -229,12 +226,8 @@ static int da9063_onkey_probe(struct platform_device *pdev)
return -ENXIO;
}
- if (pdata)
- onkey->key_power = pdata->key_power;
- else
- onkey->key_power =
- !of_property_read_bool(pdev->dev.of_node,
- "dlg,disable-key-power");
+ onkey->key_power = !of_property_read_bool(pdev->dev.of_node,
+ "dlg,disable-key-power");
onkey->input = devm_input_allocate_device(&pdev->dev);
if (!onkey->input) {
--
2.11.0
^ permalink raw reply related
* [PATCH 0/6] mfd: da9063: remove platform_data
From: Wolfram Sang @ 2019-03-18 15:47 UTC (permalink / raw)
To: linux-kernel
Cc: linux-renesas-soc, Lee Jones, Mark Brown, Support Opensource,
Wolfram Sang, linux-input
When working with this driver while debugging something else, I noticed that
there are no in-kernel users of platform_data anymore. Removing the support
simplifies the code and gets rid of quite some lines. The biggest refactoring
went to the regulator driver which could maybe benefit from more
refactorization. However, there is no in-kernel user of that driver, so no
testing. I left it at this stage. I think the changes are still at a level
where review and build-testing will give enough confidence.
Besides the regulator thing, it was tested on a Renesas Lager board (R-Car H2).
No regressions encountered. buildbot was happy, too.
The patches are based on v5.1-rc1. I'd vote for all of them going through the
MFD tree. Looking forward to comments!
Wolfram
Wolfram Sang (6):
regulator: da9063: remove platform_data support
input: da9063_onkey: remove platform_data support
mfd: da9063: remove platform_data support
regulator: da9063: move definitions out of a header into the driver
mfd: da9063: remove leftover platform_data definitions
regulator: da9063: platform_data is gone, depend on OF
drivers/input/misc/da9063_onkey.c | 11 +---
drivers/mfd/da9063-core.c | 20 +-----
drivers/mfd/da9063-i2c.c | 1 -
drivers/mfd/da9063-irq.c | 1 -
drivers/regulator/Kconfig | 2 +-
drivers/regulator/da9063-regulator.c | 61 +++++++++++++------
include/linux/mfd/da9063/pdata.h | 114 -----------------------------------
7 files changed, 49 insertions(+), 161 deletions(-)
delete mode 100644 include/linux/mfd/da9063/pdata.h
--
2.11.0
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox