* Re: [PATCH 2/3] arm64: dts: freescale: Add devicetree support for Thor96 board
[not found] ` <20191028115110.GE16985@dragon>
@ 2019-10-28 14:27 ` Manivannan Sadhasivam
2019-10-28 14:32 ` Shawn Guo
0 siblings, 1 reply; 3+ messages in thread
From: Manivannan Sadhasivam @ 2019-10-28 14:27 UTC (permalink / raw)
To: Shawn Guo
Cc: s.hauer, robh+dt, kernel, festevam, linux-imx, darshak.patel,
prajose.john, devicetree, linux-arm-kernel, linux-kernel, pavel,
linux-leds
Hi Shawn,
On Mon, Oct 28, 2019 at 07:51:12PM +0800, Shawn Guo wrote:
> On Thu, Oct 24, 2019 at 08:12:34PM +0530, Manivannan Sadhasivam wrote:
> > Add devicetree support for Thor96 board from Einfochips. This board is
> > one of the 96Boards Consumer Edition platform powered by the NXP
> > i.MX8MQ SoC.
> >
> > Following are the features supported currently:
> >
> > 1. uSD
> > 2. WiFi/BT
> > 3. Ethernet
> > 4. EEPROM (M24256)
> > 5. NOR Flash (W25Q256JW)
> > 6. 2xUSB3.0 ports and 1xUSB2.0 port at HS expansion
> >
> > More information about this board can be found in Arrow website:
> > https://www.arrow.com/en/products/i.imx8-thor96/arrow-development-tools
> >
> > Link to 96Boards CE Specification: https://linaro.co/ce-specification
> >
> > Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
> > [Mani: cleaned up for upstream]
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> > arch/arm64/boot/dts/freescale/Makefile | 1 +
> > .../boot/dts/freescale/imx8mq-thor96.dts | 581 ++++++++++++++++++
> > 2 files changed, 582 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
> >
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 93fce8f0c66d..dec1662019be 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -28,6 +28,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
> > dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
> > new file mode 100644
> > index 000000000000..e1adf24c2602
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mq-thor96.dts
> > @@ -0,0 +1,581 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2019 Einfochips
> > + * Copyright 2019 Linaro Ltd.
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx8mq.dtsi"
> > +
> > +/ {
> > + model = "Einfochips i.MX8MQ Thor96";
> > + compatible = "einfochips,imx8mq-thor96", "fsl,imx8mq";
> > +
> > + chosen {
> > + stdout-path = &uart1;
> > + };
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + reg = <0x00000000 0x40000000 0 0x80000000>;
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_leds>;
> > +
> > + user-led1 {
> > + label = "green:user1";
> > + gpios = <&gpio4 21 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > +
> > + user-led2 {
> > + label = "green:user2";
> > + gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "none";
>
> I see linux,default-trigger is defined in Documentation/devicetree/bindings/leds/common.txt
> with given string values. "none" and the following ones are not there.
> I'm not sure how this works.
>
The devicetree binding is not updated. I think folks just added triggers
to the respective places but didn't bother to update the binding.
For instance, mmc* trigger is registered here:
https://elixir.bootlin.com/linux/v5.4-rc2/source/drivers/mmc/core/host.c#L476
For `none`, it is like removing the trigger. This is the default mode if the
trigger property is not present:
https://elixir.bootlin.com/linux/v5.4-rc2/source/drivers/leds/led-triggers.c#L113
You can see the list of LED triggers by `cat`ing this file:
/sys/class/leds/<led>/trigger
Copied Pavel and LED list for reference.
> > + };
> > +
> > + user-led3 {
> > + label = "green:user3";
> > + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "mmc1";
> > + default-state = "off";
> > + };
> > +
> > + user-led4 {
> > + label = "green:user4";
> > + gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
> > + panic-indicator;
> > + linux,default-trigger = "none";
> > + };
> > +
> > + wlan-active-led {
> > + label = "yellow:wlan";
> > + gpios = <&gpio4 1 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "phy0tx";
> > + default-state = "off";
> > + };
> > +
> > + bt-active-led {
> > + label = "blue:bt";
> > + gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "hci0-power";
> > + default-state = "off";
> > + };
> > + };
> > +
> > + reg_usdhc1_vmmc: reg-usdhc1-vmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "VDD_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usdhc1_vqmmc: reg-usdhc1-vqmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "VCC_1V8_EXT";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usdhc2_vmmc: reg-usdhc2-vmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "VSD_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_reg_usdhc2>;
> > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usdhc2_vqmmc: reg-usdhc2-vqmmc {
> > + compatible = "regulator-fixed";
> > + regulator-name = "NVCC_SD2";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + sdio_pwrseq: sdio-pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wifi_reg_on>;
> > + gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
> > + };
> > +};
> > +
> > +/* LS-SPI0 */
> > +&ecspi2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_ecspi2>;
> > + status = "okay";
> > +};
> > +
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec1>;
> > + phy-mode = "rgmii-id";
> > + phy-reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
> > + phy-handle = <ðphy>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy: ethernet-phy@3 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <3>;
> > + };
> > + };
> > +};
> > +
> > +/* LS-I2C0 */
> > +&i2c1 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + pmic@8 {
> > + compatible = "fsl,pfuze100";
> > + reg = <0x8>;
> > +
> > + regulators {
> > + sw1a_reg: sw1ab {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + };
> > +
> > + sw1c_reg: sw1c {
> > + regulator-min-microvolt = <300000>;
> > + regulator-max-microvolt = <1875000>;
> > + };
> > +
> > + sw2_reg: sw2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + sw3a_reg: sw3ab {
> > + regulator-min-microvolt = <400000>;
> > + regulator-max-microvolt = <1975000>;
> > + regulator-always-on;
> > + };
> > +
> > + sw4_reg: sw4 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + swbst_reg: swbst {
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5150000>;
> > + };
> > +
> > + snvs_reg: vsnvs {
> > + regulator-min-microvolt = <1000000>;
> > + regulator-max-microvolt = <3000000>;
> > + regulator-always-on;
> > + };
> > +
> > + vref_reg: vrefddr {
> > + regulator-always-on;
> > + };
> > +
> > + vgen1_reg: vgen1 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + };
> > +
> > + vgen2_reg: vgen2 {
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1550000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen3_reg: vgen3 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen4_reg: vgen4 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen5_reg: vgen5 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vgen6_reg: vgen6 {
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +/* LS-I2C1 */
> > +&i2c2 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +
> > + eeprom: eeprom@50 {
> > + compatible = "atmel,24c256";
> > + reg = <0x50>;
> > + };
> > +};
> > +
> > +/* HS-I2C2 */
> > +&i2c3 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +};
> > +
> > +/* HS-I2C3 */
> > +&i2c4 {
> > + clock-frequency = <100000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c4>;
> > + status = "okay";
> > +};
> > +
> > +&pgc_gpu {
> > + power-supply = <&sw1a_reg>;
> > +};
> > +
> > +&pgc_vpu {
> > + power-supply = <&sw1c_reg>;
> > +};
> > +
> > +&qspi0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_qspi0>;
> > + status = "okay";
> > +
> > + flash@0 {
> > + compatible = "jedec,spi-nor";
> > + spi-max-frequency = <100000000>;
> > + reg = <0>;
> > + };
> > +};
> > +
> > +/* Debug UART */
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
> > + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
> > + status = "okay";
> > +};
> > +
> > +/* LS-UART0 */
> > +&uart2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
> > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> > + fsl,uart-has-rtscts;
>
> uart-has-rtscts
>
okay.
Thanks,
Mani
> Shawn
>
> > + status = "okay";
> > +
> > + bluetooth {
> > + compatible = "brcm,bcm43438-bt";
> > + device-wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> > + host-wakeup-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
> > + shutdown-gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_bt_gpios>;
> > + };
> > +};
> > +
> > +/* LS-UART1 */
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart3>;
> > + assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
> > + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
> > + status = "okay";
> > +};
> > +
> > +&usb3_phy1 {
> > + status = "okay";
> > +};
> > +
> > +&usb_dwc3_1 {
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +/* SDIO */
> > +&usdhc1 {
> > + #address-cells = <0x1>;
> > + #size-cells = <0x0>;
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> > + vmmc-supply = <®_usdhc1_vmmc>;
> > + vqmmc-supply = <®_usdhc1_vqmmc>;
> > + mmc-pwrseq = <&sdio_pwrseq>;
> > + bus-width = <4>;
> > + non-removable;
> > + no-sd;
> > + no-emmc;
> > + status = "okay";
> > +
> > + brcmf: wifi@1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + };
> > +};
> > +
> > +/* uSD */
> > +&usdhc2 {
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> > + vmmc-supply = <®_usdhc2_vmmc>;
> > + vqmmc-supply = <®_usdhc2_vqmmc>;
> > + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> > + bus-width = <4>;
> > + no-sdio;
> > + no-emmc;
> > + disable-wp;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wdog>;
> > + fsl,ext-reset-output;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > + pinctrl_bt_gpios: btgpiosgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SAI5_RXD1_GPIO3_IO22 0x19
> > + MX8MQ_IOMUXC_NAND_DQS_GPIO3_IO14 0x19
> > + MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19
> > + >;
> > + };
> > +
> > + pinctrl_ecspi2: ecspi2grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x16
> > + MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x16
> > + MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x16
> > + MX8MQ_IOMUXC_ECSPI2_SS0_ECSPI2_SS0 0x16
> > + >;
> > + };
> > +
> > + pinctrl_fec1: fec1grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x4
> > + MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x24
> > + MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1c
> > + MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1c
> > + MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1c
> > + MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1c
> > + MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> > + MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> > + MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> > + MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> > + MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1c
> > + MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> > + MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> > + MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1c
> > + MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x19
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
> > + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
> > + >;
> > + };
> > +
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f
> > + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f
> > + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f
> > + >;
> > + };
> > +
> > + pinctrl_i2c4: i2c4grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f
> > + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f
> > + >;
> > + };
> > +
> > + pinctrl_leds: ledsgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21 0x19
> > + MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
> > + MX8MQ_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x19
> > + MX8MQ_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19
> > + MX8MQ_IOMUXC_SAI1_RXC_GPIO4_IO1 0x19
> > + MX8MQ_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x19
> > + >;
> > + };
> > +
> > + pinctrl_qspi0: qspi0grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
> > + MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
> > + MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
> > + MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
> > + MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
> > + MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
> > +
> > + >;
> > + };
> > +
> > + pinctrl_reg_usdhc2: regusdhc2grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49
> > + MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49
> > + MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49
> > + MX8MQ_IOMUXC_UART4_RXD_UART2_DCE_CTS_B 0x49
> > + MX8MQ_IOMUXC_UART4_TXD_UART2_DCE_RTS_B 0x49
> > + >;
> > + };
> > +
> > + pinctrl_uart3: uart3grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49
> > + MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
> > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
> > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
> > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
> > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
> > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
> > + MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d
> > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd
> > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd
> > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd
> > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd
> > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd
> > + MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f
> > + MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf
> > + MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf
> > + MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf
> > + MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf
> > + MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf
> > + MX8MQ_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x85
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_gpio: usdhc2gpiogrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
> > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
> > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
> > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
> > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
> > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
> > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8c
> > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcc
> > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcc
> > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcc
> > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcc
> > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcc
> > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9c
> > + MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdc
> > + MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdc
> > + MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdc
> > + MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdc
> > + MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdc
> > + MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xcc
> > + >;
> > + };
> > +
> > + pinctrl_wdog: wdoggrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> > + >;
> > + };
> > +
> > + pinctrl_wifi_reg_on: wifiregongrp {
> > + fsl,pins = <
> > + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x17059
> > + >;
> > + };
> > +};
> > --
> > 2.17.1
> >
^ permalink raw reply [flat|nested] 3+ messages in thread