* [linux-dvb] getting started
@ 2009-03-12 21:46 Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 21:46 UTC (permalink / raw)
To: linux-dvb
I once had my TechnoTrend DVB-C driver working with linux, looking tv.
However, completely forgot how I managed that.
I think I was following the wiki
How to Obtain, Build and Install V4L-DVB Device Driver
I checked out the v4l-dvb sources using Mercurial.
However, a make failed immediately:
------------
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
benötigt von »config-compat.h«, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
-----------
Am I on the right track?
If so, what is missing?
ngong
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead linux-media@vger.kernel.org
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [linux-dvb] getting started
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
@ 2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:47 ` Rolf Schumacher
2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
2 siblings, 1 reply; 6+ messages in thread
From: Antti Palosaari @ 2009-03-12 22:02 UTC (permalink / raw)
To: linux-media; +Cc: linux-dvb
Rolf Schumacher wrote:
> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
> ./scripts/make_kconfig.pl line 32, <IN> line 4.
kernel-devel, kernel-headers, linux-devel or linux-headers package is
missing. Package name varies from distribution to distribution...
--
http://palosaari.fi/
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] getting started
2009-03-12 22:02 ` Antti Palosaari
@ 2009-03-12 22:47 ` Rolf Schumacher
0 siblings, 0 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 22:47 UTC (permalink / raw)
To: linux-media
thank you, Antti, Thomas
kernel-headers are installed.
Why does make try to read the wrong file?
My kernel is named 2.6.28-7.slh.4-sidux-686, not 2.6.28-7.slh.3-sidux-686
---------
rsc@rolf9:~/src/v4l-dvb$ make
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ?.myconfig?,
beno"tigt von ?config-compat.h?, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
rsc@rolf9:~/src/v4l-dvb$
rsc@rolf9:~/src/v4l-dvb$ ls -la
/lib/modules/2.6.28-7.slh.3-sidux-686/build/.config
ls: Zugriff auf /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config
nicht mo"glich: Datei oder Verzeichnis nicht gefunden
rsc@rolf9:~/src/v4l-dvb$ ls -la
/lib/modules/2.6.28-7.slh.4-sidux-686/build/.config
-rw-r--r-- 1 root root 95158 12. Ma"r 00:30
/lib/modules/2.6.28-7.slh.4-sidux-686/build/.config
rsc@rolf9:~/src/v4l-dvb$ hg update
0 files updated, 0 files merged, 0 files removed, 0 files unresolved
rsc@rolf9:~/src/v4l-dvb$
------------
Antti Palosaari wrote:
> Rolf Schumacher wrote:
>
>> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
>> ./scripts/make_kconfig.pl line 32, <IN> line 4.
>>
>
> kernel-devel, kernel-headers, linux-devel or linux-headers package is
> missing. Package name varies from distribution to distribution...
>
>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [linux-dvb] getting started
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
@ 2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
2 siblings, 0 replies; 6+ messages in thread
From: Thomas Kaiser @ 2009-03-12 22:04 UTC (permalink / raw)
To: linux-media; +Cc: mailinglist
Rolf Schumacher wrote:
> I once had my TechnoTrend DVB-C driver working with linux, looking tv.
> However, completely forgot how I managed that.
>
> I think I was following the wiki
>
> How to Obtain, Build and Install V4L-DVB Device Driver
>
> I checked out the v4l-dvb sources using Mercurial.
> However, a make failed immediately:
>
> ------------
> make -C /home/rsc/src/v4l-dvb/v4l
> make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
> Updating/Creating .config
> Preparing to compile for kernel version 2.6.28
> File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
> ./scripts/make_kconfig.pl line 32, <IN> line 4.
> make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
> benötigt von »config-compat.h«, zu erstellen. Schluss.
> make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
> make: *** [all] Fehler 2
> -----------
>
> Am I on the right track?
> If so, what is missing?
Kernel-headers and/or source installed?
Thomas
^ permalink raw reply [flat|nested] 6+ messages in thread
* Compro T750F - frontend initialization failing
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:04 ` Thomas Kaiser
@ 2009-03-14 5:14 ` Andrew Reay
2 siblings, 0 replies; 6+ messages in thread
From: Andrew Reay @ 2009-03-14 5:14 UTC (permalink / raw)
To: linux-media
Hi Everyone,
I'm having trouble with getting the Compro Video T750F to work under
Ubuntu 8.10. I had the Compro T300 working great but this card is still
eluding me.
Any suggestions on how to proceed from here?
The dmesg is posted below.
Thanks,
Andrew
[ 13.317113] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 13.317703] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 13.317709] saa7134 0000:04:08.0: PCI INT A -> Link[APC1] -> GSI 16
(level, low) -> IRQ 16
[ 13.317716] saa7133[0]: found at 0000:04:08.0, rev: 209, irq: 16,
latency: 32, mmio: 0xfdbfe000
[ 13.317723] saa7133[0]: subsystem: 185b:c900, board: Compro VideoMate
T750 [card=139,autodetected]
[ 13.317734] saa7133[0]: board init: gpio is 84bf00
[ 13.317746] saa7133[0]: Oops: IR config error [card=139]
[ 13.476035] saa7133[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9
1c 55 d2 b2 92
[ 13.476046] saa7133[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff
ff ff ff ff ff
[ 13.476055] saa7133[0]: i2c eeprom 20: 01 40 01 02 02 01 03 01 08 ff 00
87 ff ff ff ff
[ 13.476064] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476072] saa7133[0]: i2c eeprom 40: ff d7 00 c4 86 1e 05 ff 02 c2 ff
01 c6 ff 05 ff
[ 13.476081] saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff cb
[ 13.476089] saa7133[0]: i2c eeprom 60: 35 ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476098] saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476106] saa7133[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476115] saa7133[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476123] saa7133[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476132] saa7133[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476140] saa7133[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476149] saa7133[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476157] saa7133[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.476166] saa7133[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff
[ 13.508082] tuner 2-0062: chip found @ 0xc4 (saa7133[0])
[ 13.548912] xc2028 2-0062: creating new instance
[ 13.548916] xc2028 2-0062: type set to XCeive xc2028/xc3028 tuner
[ 13.548926] firmware: requesting xc3028-v27.fw
[ 13.999716] input: ImPS/2 Generic Wheel Mouse
as /devices/platform/i8042/serio1/input/input5
[ 14.055433] xc2028 2-0062: Loading 80 firmware images from
xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[ 14.055534] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.055940] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.055943] xc2028 2-0062: -5 returned from send
[ 14.055947] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108032] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.108570] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.108573] xc2028 2-0062: -5 returned from send
[ 14.108576] xc2028 2-0062: Error -22 while loading base firmware
[ 14.108589] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.109126] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.109128] xc2028 2-0062: -5 returned from send
[ 14.109131] xc2028 2-0062: Error -22 while loading base firmware
[ 14.165021] xc2028 2-0062: Loading firmware for type=BASE F8MHZ MTS
(7), id 0000000000000000.
[ 14.165555] xc2028 2-0062: i2c output error: rc = -5 (should be 64)
[ 14.165557] xc2028 2-0062: -5 returned from send
[ 14.165560] xc2028 2-0062: Error -22 while loading base firmware
[ 14.166394] xc2028 2-0062: Error on line 1124: -5
[ 14.173289] saa7133[0]: registered device video0 [v4l2]
[ 14.173451] saa7133[0]: registered device vbi0
[ 14.173507] saa7133[0]: registered device radio0
[ 14.174059] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 14.174064] HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23
(level, low) -> IRQ 23
[ 14.174089] HDA Intel 0000:00:10.1: setting latency timer to 64
[ 14.196322] saa7134 ALSA driver for DMA sound loaded
[ 14.196353] saa7133[0]/alsa: saa7133[0] at 0xfdbfe000 irq 16 registered
as card -2
[ 14.337099] dvb_init() allocating 1 frontend
[ 14.337105] saa7133[0]/dvb: Huh? unknown DVB card?
[ 14.337108] saa7133[0]/dvb: frontend initialization failed
^ permalink raw reply [flat|nested] 6+ messages in thread
* [linux-dvb] getting started
@ 2009-03-12 22:32 Rolf Schumacher
0 siblings, 0 replies; 6+ messages in thread
From: Rolf Schumacher @ 2009-03-12 22:32 UTC (permalink / raw)
To: linux-media
I once had my TechnoTrend DVB-C driver working with linux, looking tv.
However, completely forgot how I managed that.
I think I was following the wiki
How to Obtain, Build and Install V4L-DVB Device Driver
I checked out the v4l-dvb sources using Mercurial.
However, a make failed immediately:
------------
make -C /home/rsc/src/v4l-dvb/v4l
make[1]: Entering directory `/home/rsc/src/v4l-dvb/v4l'
Updating/Creating .config
Preparing to compile for kernel version 2.6.28
File not found: /lib/modules/2.6.28-7.slh.3-sidux-686/build/.config at
./scripts/make_kconfig.pl line 32, <IN> line 4.
make[1]: *** Keine Regel vorhanden, um das Target ».myconfig«,
benötigt von »config-compat.h«, zu erstellen. Schluss.
make[1]: Leaving directory `/home/rsc/src/v4l-dvb/v4l'
make: *** [all] Fehler 2
-----------
Am I on the right track?
If so, what is missing?
ngong
_______________________________________________
linux-dvb users mailing list
For V4L/DVB development, please use instead linux-media@vger.kernel.org
linux-dvb@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2009-03-14 5:14 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2009-03-12 21:46 [linux-dvb] getting started Rolf Schumacher
2009-03-12 22:02 ` Antti Palosaari
2009-03-12 22:47 ` Rolf Schumacher
2009-03-12 22:04 ` Thomas Kaiser
2009-03-14 5:14 ` Compro T750F - frontend initialization failing Andrew Reay
-- strict thread matches above, loose matches on Subject: below --
2009-03-12 22:32 [linux-dvb] getting started Rolf Schumacher
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox