Linux MIPS Architecture development
 help / color / mirror / Atom feed
From: "???" <Mickey@turtle.ee.ncku.edu.tw>
To: "Pete Popov" <ppopov@embeddedalley.com>
Cc: <linux-mips@linux-mips.org>
Subject: Re: Is there any means to use Cramfs and JFFS2 images as root disks?
Date: Sun, 17 Oct 2004 01:41:33 +0800	[thread overview]
Message-ID: <004b01c4b3a7$6193e810$7101a8c0@dinosaur> (raw)
In-Reply-To: 4171501D.5040506@embeddedalley.com


----- Original Message ----- 
From: "Pete Popov" <ppopov@embeddedalley.com>
To: "???" <Mickey@turtle.ee.ncku.edu.tw>
Cc: <linux-mips@linux-mips.org>
Sent: Sunday, October 17, 2004 12:45 AM
Subject: Re: Is there any means to use Cramfs and JFFS2 images as root
disks?


> ??? wrote:
> > Hi Pete,
> > How do I compile JFFS2 image and Kernel image together and by that way
> > Kernel can know where /dev/mtdblock3 is?
>
> I'm not sure a brief answer will help you, but here it is.
>
> You don't compile "jffs2 image and kernel image" together. You select
> jffs2 support in the kernel when you run something like "make
> menuconfig". You rebuild the kernel and now your kernel will have jffs2
> support. You also need your kernel to have mtd support, since that's how
> you'll access /dev/mtdblockxxxx. You then build a jffs2 image, put it in
> flash in whatever partition you want or have space for, and then boot
> the kernel with "root=/dev/mtdblockxxx".

My question still exists: YAMON doesn't know where /dev/mtdblock3 is...
How do I put JFFS2 image by YAMON onto the right location in Flash... :-)

>
> > And if I want to just write JFFS2 image to Flash, how do I do on YAMON?
>
> Yes, you can, but I don't remember the commands off the top of my head.
> On the Au1x boards, you can use yamon to erase the flash and load srec
> files directly to flash. You may also be able to load a binary file and
> store it in flash which would make it easier. Finally, you can build a
> kernel with NFS root file system, or a ramdisk, etc, -- something other
> than jffs2. Then, you can use the linux kernel to erase the mtd
> partition where you want a jffs2 image, and then copy the image to that
> partition.
>

Great! This is a good idea.
I can already boot up Linux with NFS root.
I'll give it a try to write JFFS2 root image to /dev/mtdblock on Linux
system, not on YAMON.

> > Can also I use Cramfs as root when boot up, like JFFS2?
>
> Yes, you can. The same steps above apply.
>
> Pete

Thanks and regards,
Colin

WARNING: multiple messages have this Message-ID (diff)
From: "???" <Mickey@turtle.ee.ncku.edu.tw>
To: Pete Popov <ppopov@embeddedalley.com>
Cc: linux-mips@linux-mips.org
Subject: Re: Is there any means to use Cramfs and JFFS2 images as root disks?
Date: Sun, 17 Oct 2004 01:41:33 +0800	[thread overview]
Message-ID: <004b01c4b3a7$6193e810$7101a8c0@dinosaur> (raw)
Message-ID: <20041016174133.Bsv6INyzkWGOglQ9v76MMQNbqWhVpTbUO6p0jbSrwzA@z> (raw)
In-Reply-To: 4171501D.5040506@embeddedalley.com


----- Original Message ----- 
From: "Pete Popov" <ppopov@embeddedalley.com>
To: "???" <Mickey@turtle.ee.ncku.edu.tw>
Cc: <linux-mips@linux-mips.org>
Sent: Sunday, October 17, 2004 12:45 AM
Subject: Re: Is there any means to use Cramfs and JFFS2 images as root
disks?


> ??? wrote:
> > Hi Pete,
> > How do I compile JFFS2 image and Kernel image together and by that way
> > Kernel can know where /dev/mtdblock3 is?
>
> I'm not sure a brief answer will help you, but here it is.
>
> You don't compile "jffs2 image and kernel image" together. You select
> jffs2 support in the kernel when you run something like "make
> menuconfig". You rebuild the kernel and now your kernel will have jffs2
> support. You also need your kernel to have mtd support, since that's how
> you'll access /dev/mtdblockxxxx. You then build a jffs2 image, put it in
> flash in whatever partition you want or have space for, and then boot
> the kernel with "root=/dev/mtdblockxxx".

My question still exists: YAMON doesn't know where /dev/mtdblock3 is...
How do I put JFFS2 image by YAMON onto the right location in Flash... :-)

>
> > And if I want to just write JFFS2 image to Flash, how do I do on YAMON?
>
> Yes, you can, but I don't remember the commands off the top of my head.
> On the Au1x boards, you can use yamon to erase the flash and load srec
> files directly to flash. You may also be able to load a binary file and
> store it in flash which would make it easier. Finally, you can build a
> kernel with NFS root file system, or a ramdisk, etc, -- something other
> than jffs2. Then, you can use the linux kernel to erase the mtd
> partition where you want a jffs2 image, and then copy the image to that
> partition.
>

Great! This is a good idea.
I can already boot up Linux with NFS root.
I'll give it a try to write JFFS2 root image to /dev/mtdblock on Linux
system, not on YAMON.

> > Can also I use Cramfs as root when boot up, like JFFS2?
>
> Yes, you can. The same steps above apply.
>
> Pete

Thanks and regards,
Colin

  reply	other threads:[~2004-10-16 17:42 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2004-10-15 17:31 Is there any means to use Cramfs and JFFS2 images as root disks? 林建安
2004-10-15 17:31 ` 林建安
2004-10-15 17:45 ` Pete Popov
2004-10-16  3:04   ` Eugene Surovegin
     [not found]   ` <004201c4b331$f9f6b180$7101a8c0@dinosaur>
2004-10-16 16:45     ` Pete Popov
2004-10-16 17:41       ` ??? [this message]
2004-10-16 17:41         ` ???
2004-10-16 22:04         ` Wolfgang Denk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to='004b01c4b3a7$6193e810$7101a8c0@dinosaur' \
    --to=mickey@turtle.ee.ncku.edu.tw \
    --cc=linux-mips@linux-mips.org \
    --cc=ppopov@embeddedalley.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox