* [PATCH][MIPS][1/6] AR7: core support
2007-10-11 0:48 [PATCH][MIPS][0/6] AR7: AR7 strikes back Matteo Croce
@ 2007-10-11 0:50 ` Matteo Croce
2007-10-11 0:54 ` [PATCH][MIPS][2/6] AR7: VLYNQ bus Matteo Croce
` (5 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matteo Croce @ 2007-10-11 0:50 UTC (permalink / raw)
To: linux-mips
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index f943736..a207a8b 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -16,6 +16,22 @@ choice
prompt "System type"
default SGI_IP22
+config AR7
+ bool "Texas Instruments AR7"
+ select BOOT_ELF32
+ select DMA_NONCOHERENT
+ select IRQ_CPU
+ select NO_EXCEPT_FILL
+ select SWAP_IO_SPACE
+ select SYS_HAS_CPU_MIPS32_R1
+ select SYS_HAS_EARLY_PRINTK
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_KGDB
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_BIG_ENDIAN
+ select GENERIC_GPIO
+ select GENERIC_HARDIRQS_NO__DO_IRQ
+
config MACH_ALCHEMY
bool "Alchemy processor based machines"
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index ebd5d02..905d06a 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -157,6 +157,13 @@ libs-$(CONFIG_SIBYTE_CFE) += arch/mips/sibyte/cfe/
#
#
+# Texas Instruments AR7
+#
+core-$(CONFIG_AR7) += arch/mips/ar7/
+cflags-$(CONFIG_AR7) += -Iinclude/asm-mips/ar7
+load-$(CONFIG_AR7) += 0xffffffff94100000
+
+#
# Acer PICA 61, Mips Magnum 4000 and Olivetti M700.
#
core-$(CONFIG_MACH_JAZZ) += arch/mips/jazz/
diff --git a/arch/mips/ar7/Makefile b/arch/mips/ar7/Makefile
new file mode 100644
index 0000000..7435e44
--- /dev/null
+++ b/arch/mips/ar7/Makefile
@@ -0,0 +1,10 @@
+
+obj-y := \
+ prom.o \
+ setup.o \
+ memory.o \
+ irq.o \
+ time.o \
+ platform.o \
+ gpio.o \
+ clock.o
diff --git a/arch/mips/ar7/clock.c b/arch/mips/ar7/clock.c
new file mode 100644
index 0000000..ecbcbf0
--- /dev/null
+++ b/arch/mips/ar7/clock.c
@@ -0,0 +1,485 @@
+/*
+ * Copyright (C) 2007 Felix Fietkau, Eugene Konev
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/ar7/ar7.h>
+
+#define BOOT_PLL_SOURCE_MASK 0x3
+#define CPU_PLL_SOURCE_SHIFT 16
+#define BUS_PLL_SOURCE_SHIFT 14
+#define USB_PLL_SOURCE_SHIFT 18
+#define DSP_PLL_SOURCE_SHIFT 22
+#define BOOT_PLL_SOURCE_AFE 0
+#define BOOT_PLL_SOURCE_BUS 0
+#define BOOT_PLL_SOURCE_REF 1
+#define BOOT_PLL_SOURCE_XTAL 2
+#define BOOT_PLL_SOURCE_CPU 3
+#define BOOT_PLL_BYPASS 0x00000020
+#define BOOT_PLL_ASYNC_MODE 0x02000000
+#define BOOT_PLL_2TO1_MODE 0x00008000
+
+#define TNETD7200_CLOCK_ID_CPU 0
+#define TNETD7200_CLOCK_ID_DSP 1
+#define TNETD7200_CLOCK_ID_USB 2
+
+#define TNETD7200_DEF_CPU_CLK 211000000
+#define TNETD7200_DEF_DSP_CLK 125000000
+#define TNETD7200_DEF_USB_CLK 48000000
+
+struct tnetd7300_clock {
+ volatile u32 ctrl;
+#define PREDIV_MASK 0x001f0000
+#define PREDIV_SHIFT 16
+#define POSTDIV_MASK 0x0000001f
+ u32 unused1[3];
+ volatile u32 pll;
+#define MUL_MASK 0x0000f000
+#define MUL_SHIFT 12
+#define PLL_MODE_MASK 0x00000001
+#define PLL_NDIV 0x00000800
+#define PLL_DIV 0x00000002
+#define PLL_STATUS 0x00000001
+ u32 unused2[3];
+} __packed;
+
+struct tnetd7300_clocks {
+ struct tnetd7300_clock bus;
+ struct tnetd7300_clock cpu;
+ struct tnetd7300_clock usb;
+ struct tnetd7300_clock dsp;
+} __packed;
+
+struct tnetd7200_clock {
+ volatile u32 ctrl;
+ u32 unused1[3];
+#define DIVISOR_ENABLE_MASK 0x00008000
+ volatile u32 mul;
+ volatile u32 prediv;
+ volatile u32 postdiv;
+ volatile u32 postdiv2;
+ u32 unused2[6];
+ volatile u32 cmd;
+ volatile u32 status;
+ volatile u32 cmden;
+ u32 padding[15];
+} __packed;
+
+struct tnetd7200_clocks {
+ struct tnetd7200_clock cpu;
+ struct tnetd7200_clock dsp;
+ struct tnetd7200_clock usb;
+} __packed;
+
+int ar7_cpu_clock = 150000000;
+EXPORT_SYMBOL(ar7_cpu_clock);
+int ar7_bus_clock = 125000000;
+EXPORT_SYMBOL(ar7_bus_clock);
+int ar7_dsp_clock;
+EXPORT_SYMBOL(ar7_dsp_clock);
+
+static int gcd(int a, int b)
+{
+ int c;
+
+ if (a < b) {
+ c = a;
+ a = b;
+ b = c;
+ }
+ while ((c = (a % b))) {
+ a = b;
+ b = c;
+ }
+ return b;
+}
+
+static void approximate(int base, int target, int *prediv,
+ int *postdiv, int *mul)
+{
+ int i, j, k, freq, res = target;
+ for (i = 1; i <= 16; i++)
+ for (j = 1; j <= 32; j++)
+ for (k = 1; k <= 32; k++) {
+ freq = abs(base / j * i / k - target);
+ if (freq < res) {
+ res = freq;
+ *mul = i;
+ *prediv = j;
+ *postdiv = k;
+ }
+ }
+}
+
+static void calculate(int base, int target, int *prediv, int *postdiv,
+ int *mul)
+{
+ int tmp_gcd, tmp_base, tmp_freq;
+
+ for (*prediv = 1; *prediv <= 32; (*prediv)++) {
+ tmp_base = base / *prediv;
+ tmp_gcd = gcd(target, tmp_base);
+ *mul = target / tmp_gcd;
+ *postdiv = tmp_base / tmp_gcd;
+ if ((*mul < 1) || (*mul >= 16))
+ continue;
+ if ((*postdiv > 0) & (*postdiv <= 32))
+ break;
+ }
+
+ if (base / (*prediv) * (*mul) / (*postdiv) != target) {
+ approximate(base, target, prediv, postdiv, mul);
+ tmp_freq = base / (*prediv) * (*mul) / (*postdiv);
+ printk(KERN_WARNING
+ "Adjusted requested frequency %d to %d\n",
+ target, tmp_freq);
+ }
+
+ printk(KERN_DEBUG "Clocks: prediv: %d, postdiv: %d, mul: %d\n",
+ *prediv, *postdiv, *mul);
+}
+
+static int tnetd7300_dsp_clock(void)
+{
+ u32 didr1, didr2;
+ u8 rev = ar7_chip_rev();
+ didr1 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x18));
+ didr2 = readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x1c));
+ if (didr2 & (1 << 23))
+ return 0;
+ if ((rev >= 0x23) && (rev != 0x57))
+ return 250000000;
+ if ((((didr2 & 0x1fff) << 10) | ((didr1 & 0xffc00000) >> 22))
+ > 4208000)
+ return 250000000;
+ return 0;
+}
+
+static int tnetd7300_get_clock(u32 shift, struct tnetd7300_clock *clock,
+ u32 *bootcr, u32 bus_clock)
+{
+ int product;
+ int base_clock = AR7_REF_CLOCK;
+ u32 ctrl = clock->ctrl;
+ u32 pll = clock->pll;
+ int prediv = ((ctrl & PREDIV_MASK) >> PREDIV_SHIFT) + 1;
+ int postdiv = (ctrl & POSTDIV_MASK) + 1;
+ int divisor = prediv * postdiv;
+ int mul = ((pll & MUL_MASK) >> MUL_SHIFT) + 1;
+
+ switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+ case BOOT_PLL_SOURCE_BUS:
+ base_clock = bus_clock;
+ break;
+ case BOOT_PLL_SOURCE_REF:
+ base_clock = AR7_REF_CLOCK;
+ break;
+ case BOOT_PLL_SOURCE_XTAL:
+ base_clock = AR7_XTAL_CLOCK;
+ break;
+ case BOOT_PLL_SOURCE_CPU:
+ base_clock = ar7_cpu_clock;
+ break;
+ }
+
+ if (*bootcr & BOOT_PLL_BYPASS)
+ return base_clock / divisor;
+
+ if ((pll & PLL_MODE_MASK) == 0)
+ return (base_clock >> (mul / 16 + 1)) / divisor;
+
+ if ((pll & (PLL_NDIV | PLL_DIV)) == (PLL_NDIV | PLL_DIV)) {
+ product = (mul & 1) ?
+ (base_clock * mul) >> 1 :
+ (base_clock * (mul - 1)) >> 2;
+ return product / divisor;
+ }
+
+ if (mul == 16)
+ return base_clock / divisor;
+
+ return base_clock * mul / divisor;
+}
+
+static void tnetd7300_set_clock(u32 shift, struct tnetd7300_clock *clock,
+ u32 *bootcr, u32 frequency)
+{
+ u32 status;
+ int prediv, postdiv, mul;
+ int base_clock = ar7_bus_clock;
+
+ switch ((*bootcr & (BOOT_PLL_SOURCE_MASK << shift)) >> shift) {
+ case BOOT_PLL_SOURCE_BUS:
+ base_clock = ar7_bus_clock;
+ break;
+ case BOOT_PLL_SOURCE_REF:
+ base_clock = AR7_REF_CLOCK;
+ break;
+ case BOOT_PLL_SOURCE_XTAL:
+ base_clock = AR7_XTAL_CLOCK;
+ break;
+ case BOOT_PLL_SOURCE_CPU:
+ base_clock = ar7_cpu_clock;
+ break;
+ }
+
+ calculate(base_clock, frequency, &prediv, &postdiv, &mul);
+
+ clock->ctrl = ((prediv - 1) << PREDIV_SHIFT) | (postdiv - 1);
+ mdelay(1);
+ clock->pll = 4;
+ do
+ status = clock->pll;
+ while (status & PLL_STATUS);
+ clock->pll = ((mul - 1) << MUL_SHIFT) | (0xff << 3) | 0x0e;
+ mdelay(75);
+}
+
+static void __init tnetd7300_init_clocks(void)
+{
+ u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4);
+ struct tnetd7300_clocks *clocks =
+ (struct tnetd7300_clocks *)
+ ioremap_nocache(AR7_REGS_POWER + 0x20,
+ sizeof(struct tnetd7300_clocks));
+
+ ar7_bus_clock = tnetd7300_get_clock(BUS_PLL_SOURCE_SHIFT,
+ &clocks->bus, bootcr, AR7_AFE_CLOCK);
+
+ if (*bootcr & BOOT_PLL_ASYNC_MODE)
+ ar7_cpu_clock = tnetd7300_get_clock(CPU_PLL_SOURCE_SHIFT,
+ &clocks->cpu, bootcr, AR7_AFE_CLOCK);
+ else
+ ar7_cpu_clock = ar7_bus_clock;
+/*
+ tnetd7300_set_clock(USB_PLL_SOURCE_SHIFT, &clocks->usb,
+ bootcr, 48000000);
+*/
+ if (ar7_dsp_clock == 250000000)
+ tnetd7300_set_clock(DSP_PLL_SOURCE_SHIFT, &clocks->dsp,
+ bootcr, ar7_dsp_clock);
+
+ iounmap(clocks);
+ iounmap(bootcr);
+}
+
+static int tnetd7200_get_clock(int base, struct tnetd7200_clock *clock,
+ u32 *bootcr, u32 bus_clock)
+{
+ int divisor = ((clock->prediv & 0x1f) + 1) *
+ ((clock->postdiv & 0x1f) + 1);
+
+ if (*bootcr & BOOT_PLL_BYPASS)
+ return base / divisor;
+
+ return base * ((clock->mul & 0xf) + 1) / divisor;
+}
+
+
+static void tnetd7200_set_clock(int base, struct tnetd7200_clock *clock,
+ int prediv, int postdiv, int postdiv2, int mul, u32 frequency)
+{
+ printk(KERN_INFO
+ "Clocks: base = %d, frequency = %u, prediv = %d, "
+ "postdiv = %d, postdiv2 = %d, mul = %d\n",
+ base, frequency, prediv, postdiv, postdiv2, mul);
+
+ clock->ctrl = 0;
+ clock->prediv = DIVISOR_ENABLE_MASK | ((prediv - 1) & 0x1F);
+ clock->mul = ((mul - 1) & 0xF);
+
+ for (mul = 0; mul < 2000; mul++) /* nop */;
+
+ while (clock->status & 0x1) /* nop */;
+
+ clock->postdiv = DIVISOR_ENABLE_MASK | ((postdiv - 1) & 0x1F);
+
+ clock->cmden |= 1;
+ clock->cmd |= 1;
+
+ while (clock->status & 0x1) /* nop */;
+
+ clock->postdiv2 = DIVISOR_ENABLE_MASK | ((postdiv2 - 1) & 0x1F);
+
+ clock->cmden |= 1;
+ clock->cmd |= 1;
+
+ while (clock->status & 0x1) /* nop */;
+
+ clock->ctrl |= 1;
+}
+
+static int tnetd7200_get_clock_base(int clock_id, u32 *bootcr)
+{
+ if (*bootcr & BOOT_PLL_ASYNC_MODE)
+ /* Async */
+ switch (clock_id) {
+ case TNETD7200_CLOCK_ID_DSP:
+ return AR7_REF_CLOCK;
+ default:
+ return AR7_AFE_CLOCK;
+ }
+ else
+ /* Sync */
+ if (*bootcr & BOOT_PLL_2TO1_MODE)
+ /* 2:1 */
+ switch (clock_id) {
+ case TNETD7200_CLOCK_ID_DSP:
+ return AR7_REF_CLOCK;
+ default:
+ return AR7_AFE_CLOCK;
+ }
+ else
+ /* 1:1 */
+ return AR7_REF_CLOCK;
+}
+
+
+static void __init tnetd7200_init_clocks(void)
+{
+ u32 *bootcr = (u32 *)ioremap_nocache(AR7_REGS_DCL, 4);
+ struct tnetd7200_clocks *clocks =
+ (struct tnetd7200_clocks *)
+ ioremap_nocache(AR7_REGS_POWER + 0x80,
+ sizeof(struct tnetd7200_clocks));
+ int cpu_base, cpu_mul, cpu_prediv, cpu_postdiv;
+ int dsp_base, dsp_mul, dsp_prediv, dsp_postdiv;
+ int usb_base, usb_mul, usb_prediv, usb_postdiv;
+
+/*
+ Log from Fritz!Box 7170 Annex B:
+
+ CPU revision is: 00018448
+ Clocks: Async mode
+ Clocks: Setting DSP clock
+ Clocks: prediv: 1, postdiv: 1, mul: 5
+ Clocks: base = 25000000, frequency = 125000000, prediv = 1,
+ postdiv = 2, postdiv2 = 1, mul = 10
+ Clocks: Setting CPU clock
+ Adjusted requested frequency 211000000 to 211968000
+ Clocks: prediv: 1, postdiv: 1, mul: 6
+ Clocks: base = 35328000, frequency = 211968000, prediv = 1,
+ postdiv = 1, postdiv2 = -1, mul = 6
+ Clocks: Setting USB clock
+ Adjusted requested frequency 48000000 to 48076920
+ Clocks: prediv: 13, postdiv: 1, mul: 5
+ Clocks: base = 125000000, frequency = 48000000, prediv = 13,
+ postdiv = 1, postdiv2 = -1, mul = 5
+
+ DSL didn't work if you didn't set the postdiv 2:1 postdiv2 combination,
+ driver hung on startup.
+ Haven't tested this on a synchronous board,
+ neither do i know what to do with ar7_dsp_clock
+*/
+
+ cpu_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_CPU, bootcr);
+ dsp_base = tnetd7200_get_clock_base(TNETD7200_CLOCK_ID_DSP, bootcr);
+
+ if (*bootcr & BOOT_PLL_ASYNC_MODE) {
+ printk(KERN_INFO "Clocks: Async mode\n");
+
+ printk(KERN_INFO "Clocks: Setting DSP clock\n");
+ calculate(dsp_base, TNETD7200_DEF_DSP_CLK,
+ &dsp_prediv, &dsp_postdiv, &dsp_mul);
+ ar7_bus_clock =
+ ((dsp_base / dsp_prediv) * dsp_mul) / dsp_postdiv;
+ tnetd7200_set_clock(dsp_base, &clocks->dsp,
+ dsp_prediv, dsp_postdiv * 2, dsp_postdiv, dsp_mul * 2,
+ ar7_bus_clock);
+
+ printk(KERN_INFO "Clocks: Setting CPU clock\n");
+ calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+ &cpu_postdiv, &cpu_mul);
+ ar7_cpu_clock =
+ ((cpu_base / cpu_prediv) * cpu_mul) / cpu_postdiv;
+ tnetd7200_set_clock(cpu_base, &clocks->cpu,
+ cpu_prediv, cpu_postdiv, -1, cpu_mul,
+ ar7_cpu_clock);
+
+ } else
+ if (*bootcr & BOOT_PLL_2TO1_MODE) {
+ printk(KERN_INFO "Clocks: Sync 2:1 mode\n");
+
+ printk(KERN_INFO "Clocks: Setting CPU clock\n");
+ calculate(cpu_base, TNETD7200_DEF_CPU_CLK, &cpu_prediv,
+ &cpu_postdiv, &cpu_mul);
+ ar7_cpu_clock = ((cpu_base / cpu_prediv) * cpu_mul)
+ / cpu_postdiv;
+ tnetd7200_set_clock(cpu_base, &clocks->cpu,
+ cpu_prediv, cpu_postdiv, -1, cpu_mul,
+ ar7_cpu_clock);
+
+ printk(KERN_INFO "Clocks: Setting DSP clock\n");
+ calculate(dsp_base, TNETD7200_DEF_DSP_CLK, &dsp_prediv,
+ &dsp_postdiv, &dsp_mul);
+ ar7_bus_clock = ar7_cpu_clock / 2;
+ tnetd7200_set_clock(dsp_base, &clocks->dsp,
+ dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+ dsp_mul * 2, ar7_bus_clock);
+ } else {
+ printk(KERN_INFO "Clocks: Sync 1:1 mode\n");
+
+ printk(KERN_INFO "Clocks: Setting DSP clock\n");
+ calculate(dsp_base, TNETD7200_DEF_CPU_CLK, &dsp_prediv,
+ &dsp_postdiv, &dsp_mul);
+ ar7_bus_clock = ((dsp_base / dsp_prediv) * dsp_mul)
+ / dsp_postdiv;
+ tnetd7200_set_clock(dsp_base, &clocks->dsp,
+ dsp_prediv, dsp_postdiv * 2, dsp_postdiv,
+ dsp_mul * 2, ar7_bus_clock);
+
+ ar7_cpu_clock = ar7_bus_clock;
+ }
+
+ printk(KERN_INFO "Clocks: Setting USB clock\n");
+ usb_base = ar7_bus_clock;
+ calculate(usb_base, TNETD7200_DEF_USB_CLK, &usb_prediv,
+ &usb_postdiv, &usb_mul);
+ tnetd7200_set_clock(usb_base, &clocks->usb,
+ usb_prediv, usb_postdiv, -1, usb_mul,
+ TNETD7200_DEF_USB_CLK);
+
+ #warning FIXME
+ ar7_dsp_clock = ar7_cpu_clock;
+
+ iounmap(clocks);
+ iounmap(bootcr);
+}
+
+void __init ar7_init_clocks(void)
+{
+ switch (ar7_chip_id()) {
+ case AR7_CHIP_7100:
+#warning FIXME: Check if the new 7200 clock init works for 7100
+ tnetd7200_init_clocks();
+ break;
+ case AR7_CHIP_7200:
+ tnetd7200_init_clocks();
+ break;
+ case AR7_CHIP_7300:
+ ar7_dsp_clock = tnetd7300_dsp_clock();
+ tnetd7300_init_clocks();
+ break;
+ default:
+ break;
+ }
+}
diff --git a/arch/mips/ar7/gpio.c b/arch/mips/ar7/gpio.c
new file mode 100644
index 0000000..7ca7dc9
--- /dev/null
+++ b/arch/mips/ar7/gpio.c
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2007 Felix Fietkau, Eugene Konev
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/module.h>
+
+#include <asm/ar7/gpio.h>
+
+static const char *ar7_gpio_list[AR7_GPIO_MAX] = { 0, };
+
+int gpio_request(unsigned gpio, const char *label)
+{
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ if (ar7_gpio_list[gpio])
+ return -EBUSY;
+
+ if (label) {
+ ar7_gpio_list[gpio] = label;
+ } else {
+ ar7_gpio_list[gpio] = "busy";
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(gpio_request);
+
+void gpio_free(unsigned gpio)
+{
+ BUG_ON(!ar7_gpio_list[gpio]);
+ ar7_gpio_list[gpio] = NULL;
+}
+EXPORT_SYMBOL(gpio_free);
diff --git a/arch/mips/ar7/irq.c b/arch/mips/ar7/irq.c
new file mode 100644
index 0000000..e9e0b15
--- /dev/null
+++ b/arch/mips/ar7/irq.c
@@ -0,0 +1,182 @@
+/*
+ * Copyright (C) 2006, 2007 Felix Fietkau, Eugene Konev
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+
+#include <asm/irq_cpu.h>
+#include <asm/mipsregs.h>
+#include <asm/ar7/ar7.h>
+
+#define EXCEPT_OFFSET 0x80
+#define PACE_OFFSET 0xA0
+#define CHNLS_OFFSET 0x200
+
+#define REG_OFFSET(irq, reg) ((irq) / 32 * 0x4 + reg * 0x10)
+#define SEC_REG_OFFSET(reg) (EXCEPT_OFFSET + reg * 0x8)
+#define SEC_SR_OFFSET (SEC_REG_OFFSET(0)) /* 0x80 */
+#define CR_OFFSET(irq) (REG_OFFSET(irq, 1)) /* 0x10 */
+#define SEC_CR_OFFSET (SEC_REG_OFFSET(1)) /* 0x88 */
+#define ESR_OFFSET(irq) (REG_OFFSET(irq, 2)) /* 0x20 */
+#define SEC_ESR_OFFSET (SEC_REG_OFFSET(2)) /* 0x90 */
+#define ECR_OFFSET(irq) (REG_OFFSET(irq, 3)) /* 0x30 */
+#define SEC_ECR_OFFSET (SEC_REG_OFFSET(3)) /* 0x98 */
+#define PIR_OFFSET (0x40)
+#define MSR_OFFSET (0x44)
+#define PM_OFFSET(irq) (REG_OFFSET(irq, 5)) /* 0x50 */
+#define TM_OFFSET(irq) (REG_OFFSET(irq, 6)) /* 0x60 */
+
+#define REG(addr) ((u32 *)(KSEG1ADDR(AR7_REGS_IRQ) + addr))
+
+#define CHNL_OFFSET(chnl) (CHNLS_OFFSET + (chnl * 4))
+
+static void ar7_unmask_irq(unsigned int irq_nr);
+static void ar7_mask_irq(unsigned int irq_nr);
+static void ar7_ack_irq(unsigned int irq_nr);
+static void ar7_unmask_sec_irq(unsigned int irq_nr);
+static void ar7_mask_sec_irq(unsigned int irq_nr);
+static void ar7_ack_sec_irq(unsigned int irq_nr);
+static void ar7_cascade(void);
+static void ar7_irq_init(int base);
+static int ar7_irq_base;
+
+static struct irq_chip ar7_irq_type = {
+ .name = "AR7",
+ .unmask = ar7_unmask_irq,
+ .mask = ar7_mask_irq,
+ .ack = ar7_ack_irq
+};
+
+static struct irq_chip ar7_sec_irq_type = {
+ .name = "AR7",
+ .unmask = ar7_unmask_sec_irq,
+ .mask = ar7_mask_sec_irq,
+ .ack = ar7_ack_sec_irq,
+};
+
+static struct irqaction ar7_cascade_action = {
+ .handler = no_action,
+ .name = "AR7 cascade interrupt"
+};
+
+static void ar7_unmask_irq(unsigned int irq)
+{
+ writel(1 << ((irq - ar7_irq_base) % 32),
+ REG(ESR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_mask_irq(unsigned int irq)
+{
+ writel(1 << ((irq - ar7_irq_base) % 32),
+ REG(ECR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_ack_irq(unsigned int irq)
+{
+ writel(1 << ((irq - ar7_irq_base) % 32),
+ REG(CR_OFFSET(irq - ar7_irq_base)));
+}
+
+static void ar7_unmask_sec_irq(unsigned int irq)
+{
+ writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ESR_OFFSET));
+}
+
+static void ar7_mask_sec_irq(unsigned int irq)
+{
+ writel(1 << (irq - ar7_irq_base - 40), REG(SEC_ECR_OFFSET));
+}
+
+static void ar7_ack_sec_irq(unsigned int irq)
+{
+ writel(1 << (irq - ar7_irq_base - 40), REG(SEC_CR_OFFSET));
+}
+
+void __init arch_init_irq(void) {
+ mips_cpu_irq_init();
+ ar7_irq_init(8);
+}
+
+static void __init ar7_irq_init(int base)
+{
+ int i;
+ /*
+ * Disable interrupts and clear pending
+ */
+ writel(0xffffffff, REG(ECR_OFFSET(0)));
+ writel(0xff, REG(ECR_OFFSET(32)));
+ writel(0xffffffff, REG(SEC_ECR_OFFSET));
+ writel(0xffffffff, REG(CR_OFFSET(0)));
+ writel(0xff, REG(CR_OFFSET(32)));
+ writel(0xffffffff, REG(SEC_CR_OFFSET));
+
+ ar7_irq_base = base;
+
+ for (i = 0; i < 40; i++) {
+ writel(i, REG(CHNL_OFFSET(i)));
+ /* Primary IRQ's */
+ set_irq_chip_and_handler(base + i, &ar7_irq_type,
+ handle_level_irq);
+ /* Secondary IRQ's */
+ if (i < 32)
+ set_irq_chip_and_handler(base + i + 40,
+ &ar7_sec_irq_type,
+ handle_level_irq);
+ }
+
+ setup_irq(2, &ar7_cascade_action);
+ setup_irq(ar7_irq_base, &ar7_cascade_action);
+ set_c0_status(IE_IRQ0);
+}
+
+static void ar7_cascade(void)
+{
+ u32 status;
+ int i, irq;
+
+ /* Primary IRQ's */
+ irq = readl(REG(PIR_OFFSET)) & 0x3f;
+ if (irq) {
+ do_IRQ(ar7_irq_base + irq);
+ return;
+ }
+
+ /* Secondary IRQ's are cascaded through primary '0' */
+ writel(1, REG(CR_OFFSET(irq)));
+ status = readl(REG(SEC_SR_OFFSET));
+ for (i = 0; i < 32; i++) {
+ if (status & 1) {
+ do_IRQ(ar7_irq_base + i + 40);
+ return;
+ }
+ status >>= 1;
+ }
+
+ spurious_interrupt();
+}
+
+asmlinkage void plat_irq_dispatch(void)
+{
+ unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
+ if (pending & STATUSF_IP7) /* cpu timer */
+ do_IRQ(7);
+ else if (pending & STATUSF_IP2) /* int0 hardware line */
+ ar7_cascade();
+ else
+ spurious_interrupt();
+}
diff --git a/arch/mips/ar7/memory.c b/arch/mips/ar7/memory.c
new file mode 100644
index 0000000..65a094c
--- /dev/null
+++ b/arch/mips/ar7/memory.c
@@ -0,0 +1,73 @@
+/*
+ * Copyright (C) 2007 OpenWrt.org
+ *
+ * Based on arch/mips/mm/init.c
+ * Copyright (C) 1994 - 2000 Ralf Baechle
+ * Copyright (C) 1999, 2000 Silicon Graphics, Inc.
+ * Kevin D. Kissell, kevink@mips.com and Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+#include <linux/bootmem.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/pfn.h>
+#include <linux/proc_fs.h>
+#include <linux/string.h>
+#include <linux/swap.h>
+
+#include <asm/bootinfo.h>
+#include <asm/page.h>
+#include <asm/sections.h>
+
+#include <asm/mips-boards/prom.h>
+
+static int __init memsize(void)
+{
+ u32 size = (64 << 20);
+ volatile u32 *addr = (u32 *)KSEG1ADDR(0x14000000 + size - 4);
+ u32 *kernel_end = (u32 *)KSEG1ADDR(CPHYSADDR((u32)&_end));
+
+ while (addr > kernel_end) {
+ *addr = (u32)addr;
+ size >>= 1;
+ addr -= size >> 2;
+ }
+
+ do {
+ addr += size >> 2;
+ if (*addr != (u32)addr)
+ break;
+ size <<= 1;
+ } while (size < (64 << 20));
+
+ return size;
+}
+
+void __init prom_meminit(void)
+{
+ unsigned long pages;
+
+ pages = memsize() >> PAGE_SHIFT;
+ add_memory_region(PHYS_OFFSET, pages << PAGE_SHIFT,
+ BOOT_MEM_RAM);
+}
+
+void __init prom_free_prom_memory(void)
+{
+ return;
+}
diff --git a/arch/mips/ar7/platform.c b/arch/mips/ar7/platform.c
new file mode 100644
index 0000000..5b345a5
--- /dev/null
+++ b/arch/mips/ar7/platform.c
@@ -0,0 +1,494 @@
+/*
+ * Copyright (C) 2006, 2007 Felix Fietkau, Eugene Konev
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/autoconf.h>
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/physmap.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/version.h>
+#include <linux/vlynq.h>
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,23)
+#include <linux/leds.h>
+#endif
+
+#include <asm/addrspace.h>
+#include <asm/ar7/ar7.h>
+#include <asm/ar7/gpio.h>
+#include <asm/ar7/prom.h>
+
+struct plat_vlynq_data {
+ struct plat_vlynq_ops ops;
+ int gpio_bit;
+ int reset_bit;
+};
+
+
+static int vlynq_on(struct vlynq_device *dev)
+{
+ int result;
+ struct plat_vlynq_data *pdata = dev->dev.platform_data;
+
+ if ((result = gpio_request(pdata->gpio_bit, "vlynq")))
+ goto out;
+
+ ar7_device_reset(pdata->reset_bit);
+
+ if ((result = ar7_gpio_disable(pdata->gpio_bit)))
+ goto out_enabled;
+
+ if ((result = ar7_gpio_enable(pdata->gpio_bit)))
+ goto out_enabled;
+
+ if ((result = gpio_direction_output(pdata->gpio_bit, 0)))
+ goto out_gpio_enabled;
+
+ mdelay(50);
+
+ gpio_set_value(pdata->gpio_bit, 1);
+ mdelay(50);
+
+ return 0;
+
+out_gpio_enabled:
+ ar7_gpio_disable(pdata->gpio_bit);
+out_enabled:
+ ar7_device_disable(pdata->reset_bit);
+ gpio_free(pdata->gpio_bit);
+out:
+ return result;
+}
+
+static void vlynq_off(struct vlynq_device *dev)
+{
+ struct plat_vlynq_data *pdata = dev->dev.platform_data;
+ ar7_gpio_disable(pdata->gpio_bit);
+ gpio_free(pdata->gpio_bit);
+ ar7_device_disable(pdata->reset_bit);
+}
+
+static struct resource physmap_flash_resource = {
+ .name = "mem",
+ .flags = IORESOURCE_MEM,
+ .start = 0x10000000,
+ .end = 0x107fffff,
+};
+
+static struct resource cpmac_low_res[] = {
+ {
+ .name = "regs",
+ .flags = IORESOURCE_MEM,
+ .start = AR7_REGS_MAC0,
+ .end = AR7_REGS_MAC0 + 0x7ff,
+ },
+ {
+ .name = "irq",
+ .flags = IORESOURCE_IRQ,
+ .start = 27,
+ .end = 27,
+ },
+};
+
+static struct resource cpmac_high_res[] = {
+ {
+ .name = "regs",
+ .flags = IORESOURCE_MEM,
+ .start = AR7_REGS_MAC1,
+ .end = AR7_REGS_MAC1 + 0x7ff,
+ },
+ {
+ .name = "irq",
+ .flags = IORESOURCE_IRQ,
+ .start = 41,
+ .end = 41,
+ },
+};
+
+static struct resource vlynq_low_res[] = {
+ {
+ .name = "regs",
+ .flags = IORESOURCE_MEM,
+ .start = AR7_REGS_VLYNQ0,
+ .end = AR7_REGS_VLYNQ0 + 0xff,
+ },
+ {
+ .name = "irq",
+ .flags = IORESOURCE_IRQ,
+ .start = 29,
+ .end = 29,
+ },
+ {
+ .name = "mem",
+ .flags = IORESOURCE_MEM,
+ .start = 0x04000000,
+ .end = 0x04ffffff,
+ },
+ {
+ .name = "devirq",
+ .flags = IORESOURCE_IRQ,
+ .start = 80,
+ .end = 111,
+ },
+};
+
+static struct resource vlynq_high_res[] = {
+ {
+ .name = "regs",
+ .flags = IORESOURCE_MEM,
+ .start = AR7_REGS_VLYNQ1,
+ .end = AR7_REGS_VLYNQ1 + 0xff,
+ },
+ {
+ .name = "irq",
+ .flags = IORESOURCE_IRQ,
+ .start = 33,
+ .end = 33,
+ },
+ {
+ .name = "mem",
+ .flags = IORESOURCE_MEM,
+ .start = 0x0c000000,
+ .end = 0x0cffffff,
+ },
+ {
+ .name = "devirq",
+ .flags = IORESOURCE_IRQ,
+ .start = 112,
+ .end = 143,
+ },
+};
+
+static struct resource usb_res[] = {
+ {
+ .name = "regs",
+ .flags = IORESOURCE_MEM,
+ .start = AR7_REGS_USB,
+ .end = AR7_REGS_USB + 0xff,
+ },
+ {
+ .name = "irq",
+ .flags = IORESOURCE_IRQ,
+ .start = 32,
+ .end = 32,
+ },
+ {
+ .name = "mem",
+ .flags = IORESOURCE_MEM,
+ .start = 0x03400000,
+ .end = 0x034001fff,
+ },
+};
+
+static struct physmap_flash_data physmap_flash_data = {
+ .width = 2,
+};
+
+static struct plat_cpmac_data cpmac_low_data = {
+ .reset_bit = 17,
+ .power_bit = 20,
+ .phy_mask = 0x80000000,
+};
+
+static struct plat_cpmac_data cpmac_high_data = {
+ .reset_bit = 21,
+ .power_bit = 22,
+ .phy_mask = 0x7fffffff,
+};
+
+static struct plat_vlynq_data vlynq_low_data = {
+ .ops.on = vlynq_on,
+ .ops.off = vlynq_off,
+ .reset_bit = 20,
+ .gpio_bit = 18,
+};
+
+static struct plat_vlynq_data vlynq_high_data = {
+ .ops.on = vlynq_on,
+ .ops.off = vlynq_off,
+ .reset_bit = 16,
+ .gpio_bit = 19,
+};
+
+static struct platform_device physmap_flash = {
+ .id = 0,
+ .name = "physmap-flash",
+ .dev.platform_data = &physmap_flash_data,
+ .resource = &physmap_flash_resource,
+ .num_resources = 1,
+};
+
+static u64 cpmac_dma_mask = DMA_32BIT_MASK;
+static struct platform_device cpmac_low = {
+ .id = 0,
+ .name = "cpmac",
+ .dev = {
+ .dma_mask = &cpmac_dma_mask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ .platform_data = &cpmac_low_data,
+ },
+ .resource = cpmac_low_res,
+ .num_resources = ARRAY_SIZE(cpmac_low_res),
+};
+
+static struct platform_device cpmac_high = {
+ .id = 1,
+ .name = "cpmac",
+ .dev = {
+ .dma_mask = &cpmac_dma_mask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ .platform_data = &cpmac_high_data,
+ },
+ .resource = cpmac_high_res,
+ .num_resources = ARRAY_SIZE(cpmac_high_res),
+};
+
+static struct platform_device vlynq_low = {
+ .id = 0,
+ .name = "vlynq",
+ .dev.platform_data = &vlynq_low_data,
+ .resource = vlynq_low_res,
+ .num_resources = ARRAY_SIZE(vlynq_low_res),
+};
+
+static struct platform_device vlynq_high = {
+ .id = 1,
+ .name = "vlynq",
+ .dev.platform_data = &vlynq_high_data,
+ .resource = vlynq_high_res,
+ .num_resources = ARRAY_SIZE(vlynq_high_res),
+};
+
+
+/* This is proper way to define uart ports, but they are then detected
+ * as xscale and, obviously, don't work...
+ */
+#if !defined(CONFIG_SERIAL_8250)
+
+static struct plat_serial8250_port uart0_data = {
+ .mapbase = AR7_REGS_UART0,
+ .irq = AR7_IRQ_UART0,
+ .regshift = 2,
+ .iotype = UPIO_MEM,
+ .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
+};
+
+static struct plat_serial8250_port uart1_data = {
+ .mapbase = UR8_REGS_UART1,
+ .irq = AR7_IRQ_UART1,
+ .regshift = 2,
+ .iotype = UPIO_MEM,
+ .flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP,
+};
+
+static struct plat_serial8250_port uart_data[] = {
+ uart0_data,
+ uart1_data,
+ { .flags = 0 }
+};
+
+static struct plat_serial8250_port uart_data_single[] = {
+ uart0_data,
+ { .flags = 0 }
+};
+
+static struct platform_device uart = {
+ .id = 0,
+ .name = "serial8250",
+ .dev.platform_data = uart_data_single
+};
+#endif
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,23)
+static struct gpio_led default_leds[] = {
+ { .name = "status", .gpio = 8, .active_low = 1, },
+};
+
+static struct gpio_led fb_leds[] = {
+ { .name = "1", .gpio = 7, },
+ { .name = "2", .gpio = 13, .active_low = 1, },
+ { .name = "3", .gpio = 10, .active_low = 1, },
+ { .name = "4", .gpio = 12, .active_low = 1, },
+ { .name = "5", .gpio = 9, .active_low = 1, },
+};
+
+static struct gpio_led fb_fon_leds[] = {
+ { .name = "1", .gpio = 8, },
+ { .name = "2", .gpio = 3, .active_low = 1, },
+ { .name = "3", .gpio = 5, },
+ { .name = "4", .gpio = 4, .active_low = 1, },
+ { .name = "5", .gpio = 11, .active_low = 1, },
+};
+
+static struct gpio_led_platform_data ar7_led_data;
+
+static struct platform_device ar7_gpio_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &ar7_led_data,
+ }
+};
+#endif
+
+static struct platform_device ar7_udc = {
+ .id = -1,
+ .name = "ar7_udc",
+ .resource = usb_res,
+ .num_resources = ARRAY_SIZE(usb_res),
+};
+
+static inline unsigned char char2hex(char h)
+{
+ switch (h) {
+ case '0': case '1': case '2': case '3': case '4':
+ case '5': case '6': case '7': case '8': case '9':
+ return h - '0';
+ case 'A': case 'B': case 'C': case 'D': case 'E': case 'F':
+ return h - 'A' + 10;
+ case 'a': case 'b': case 'c': case 'd': case 'e': case 'f':
+ return h - 'a' + 10;
+ default:
+ return 0;
+ }
+}
+
+static void cpmac_get_mac(int instance, unsigned char *dev_addr)
+{
+ int i;
+ char name[5], default_mac[] = "00:00:00:12:34:56", *mac;
+
+ mac = NULL;
+ sprintf(name, "mac%c", 'a' + instance);
+ mac = prom_getenv(name);
+ if (!mac) {
+ sprintf(name, "mac%c", 'a');
+ mac = prom_getenv(name);
+ }
+ if (!mac)
+ mac = default_mac;
+ for (i = 0; i < 6; i++)
+ dev_addr[i] = (char2hex(mac[i * 3]) << 4) +
+ char2hex(mac[i * 3 + 1]);
+}
+
+static int __init ar7_register_devices(void)
+{
+ int res;
+
+#ifdef CONFIG_SERIAL_8250
+
+ static struct uart_port uart_port[2];
+
+ memset(uart_port, 0, sizeof(struct uart_port) * 2);
+
+ uart_port[0].type = PORT_AR7;
+ uart_port[0].line = 0;
+ uart_port[0].irq = AR7_IRQ_UART0;
+ uart_port[0].uartclk = ar7_bus_freq() / 2;
+ uart_port[0].iotype = UPIO_MEM;
+ uart_port[0].mapbase = AR7_REGS_UART0;
+ uart_port[0].membase = ioremap(uart_port[0].mapbase, 256);
+ uart_port[0].regshift = 2;
+ res = early_serial_setup(&uart_port[0]);
+ if (res)
+ return res;
+
+
+ /* Only TNETD73xx have a second serial port */
+ if (ar7_has_second_uart()) {
+ uart_port[1].type = PORT_AR7;
+ uart_port[1].line = 1;
+ uart_port[1].irq = AR7_IRQ_UART1;
+ uart_port[1].uartclk = ar7_bus_freq() / 2;
+ uart_port[1].iotype = UPIO_MEM;
+ uart_port[1].mapbase = UR8_REGS_UART1;
+ uart_port[1].membase = ioremap(uart_port[1].mapbase, 256);
+ uart_port[1].regshift = 2;
+ res = early_serial_setup(&uart_port[1]);
+ if (res)
+ return res;
+ }
+
+#else /* !CONFIG_SERIAL_8250 */
+
+ uart_data[0].uartclk = ar7_bus_freq() / 2;
+ uart_data[1].uartclk = uart_data[0].uartclk;
+
+ /* Only TNETD73xx have a second serial port */
+ if (ar7_has_second_uart())
+ uart.dev.platform_data = uart_data;
+
+ res = platform_device_register(&uart);
+ if (res)
+ return res;
+
+#endif /* CONFIG_SERIAL_8250 */
+
+ res = platform_device_register(&physmap_flash);
+ if (res)
+ return res;
+
+ res = platform_device_register(&vlynq_low);
+ if (res)
+ return res;
+
+ ar7_device_disable(vlynq_low_data.reset_bit);
+ if (ar7_has_high_vlynq()) {
+ ar7_device_disable(vlynq_high_data.reset_bit);
+ res = platform_device_register(&vlynq_high);
+ if (res)
+ return res;
+ }
+
+ if (ar7_has_high_cpmac()) {
+ cpmac_get_mac(1, cpmac_high_data.dev_addr);
+ res = platform_device_register(&cpmac_high);
+ if (res)
+ return res;
+ } else {
+ cpmac_low_data.phy_mask = 0xffffffff;
+ }
+
+ cpmac_get_mac(0, cpmac_low_data.dev_addr);
+ res = platform_device_register(&cpmac_low);
+ if (res)
+ return res;
+
+#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,23)
+#warning FIXME: add model detection
+ ar7_led_data.num_leds = ARRAY_SIZE(default_leds);
+ ar7_led_data.leds = default_leds;
+ res = platform_device_register(&ar7_gpio_leds);
+#endif
+ if (res)
+ return res;
+
+ res = platform_device_register(&ar7_udc);
+
+ return res;
+}
+
+
+arch_initcall(ar7_register_devices);
diff --git a/arch/mips/ar7/prom.c b/arch/mips/ar7/prom.c
new file mode 100644
index 0000000..65fe0c0
--- /dev/null
+++ b/arch/mips/ar7/prom.c
@@ -0,0 +1,324 @@
+/*
+ * Copyright (C) 2006, 2007 OpenWrt.org
+ *
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * Putting things on the screen/serial line using YAMONs facilities.
+ */
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/serial_reg.h>
+#include <linux/spinlock.h>
+#include <linux/module.h>
+#include <linux/string.h>
+#include <linux/io.h>
+#include <asm/bootinfo.h>
+#include <asm/gdb-stub.h>
+
+#include <asm/ar7/ar7.h>
+#include <asm/ar7/prom.h>
+
+#define MAX_ENTRY 80
+
+struct env_var {
+ char *name;
+ char *value;
+};
+
+static struct env_var adam2_env[MAX_ENTRY] = { { 0, }, };
+
+char *prom_getenv(char *name)
+{
+ int i;
+ for (i = 0; (i < MAX_ENTRY) && adam2_env[i].name; i++)
+ if (!strcmp(name, adam2_env[i].name))
+ return adam2_env[i].value;
+
+ return NULL;
+}
+EXPORT_SYMBOL(prom_getenv);
+
+char * __init prom_getcmdline(void)
+{
+ return &(arcs_cmdline[0]);
+}
+
+static void __init ar7_init_cmdline(int argc, char *argv[])
+{
+ char *cp;
+ int actr;
+
+ actr = 1; /* Always ignore argv[0] */
+
+ cp = &(arcs_cmdline[0]);
+ while (actr < argc) {
+ strcpy(cp, argv[actr]);
+ cp += strlen(argv[actr]);
+ *cp++ = ' ';
+ actr++;
+ }
+ if (cp != &(arcs_cmdline[0])) {
+ /* get rid of trailing space */
+ --cp;
+ *cp = '\0';
+ }
+}
+
+struct psbl_rec {
+ u32 psbl_size;
+ u32 env_base;
+ u32 env_size;
+ u32 ffs_base;
+ u32 ffs_size;
+};
+
+static __initdata char psp_env_version[] = "TIENV0.8";
+
+struct psp_env_chunk {
+ u8 num;
+ u8 ctrl;
+ u16 csum;
+ u8 len;
+ char data[11];
+} __attribute__ ((packed));
+
+struct psp_var_map_entry {
+ u8 num;
+ char *value;
+};
+
+static struct psp_var_map_entry psp_var_map[] = {
+ { 1, "cpufrequency" },
+ { 2, "memsize" },
+ { 3, "flashsize" },
+ { 4, "modetty0" },
+ { 5, "modetty1" },
+ { 8, "maca" },
+ { 9, "macb" },
+ { 28, "sysfrequency" },
+ { 38, "mipsfrequency" },
+};
+
+/*
+
+Well-known variable (num is looked up in table above for matching variable name)
+Example: cpufrequency=211968000
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 01 |CTRL|CHECKSUM | 01 | _2 | _1 | _1 | _9 | _6 | _8 | _0 | _0 | _0 | \0 | FF
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in a single chunk
+Example: NAME=VALUE
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 01 | _N | _A | _M | _E | _0 | _V | _A | _L | _U | _E | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Name=Value pair in 2 chunks (len is the number of chunks)
+Example: bootloaderVersion=1.3.7.15
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| 00 |CTRL|CHECKSUM | 02 | _b | _o | _o | _t | _l | _o | _a | _d | _e | _r | _V
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+| _e | _r | _s | _i | _o | _n | \0 | _1 | _. | _3 | _. | _7 | _. | _1 | _5 | \0
++----+----+----+----+----+----+----+----+----+----+----+----+----+----+----+---
+
+Data is padded with 0xFF
+
+*/
+
+#define PSP_ENV_SIZE 4096
+
+static char psp_env_data[PSP_ENV_SIZE] = { 0, };
+
+static char * __init lookup_psp_var_map(u8 num)
+{
+ int i;
+
+ for (i = 0; i < sizeof(psp_var_map); i++)
+ if (psp_var_map[i].num == num)
+ return psp_var_map[i].value;
+
+ return NULL;
+}
+
+static void __init add_adam2_var(char *name, char *value)
+{
+ int i;
+ for (i = 0; i < MAX_ENTRY; i++) {
+ if (!adam2_env[i].name) {
+ adam2_env[i].name = name;
+ adam2_env[i].value = value;
+ return;
+ } else if (!strcmp(adam2_env[i].name, name)) {
+ adam2_env[i].value = value;
+ return;
+ }
+ }
+}
+
+static int __init parse_psp_env(void *psp_env_base)
+{
+ int i, n;
+ char *name, *value;
+ struct psp_env_chunk *chunks = (struct psp_env_chunk *)psp_env_data;
+
+ memcpy_fromio(chunks, psp_env_base, PSP_ENV_SIZE);
+
+ i = 1;
+ n = PSP_ENV_SIZE / sizeof(struct psp_env_chunk);
+ while (i < n) {
+ if ((chunks[i].num == 0xff) || ((i + chunks[i].len) > n))
+ break;
+ value = chunks[i].data;
+ if (chunks[i].num) {
+ name = lookup_psp_var_map(chunks[i].num);
+ } else {
+ name = value;
+ value += strlen(name) + 1;
+ }
+ if (name)
+ add_adam2_var(name, value);
+ i += chunks[i].len;
+ }
+ return 0;
+}
+
+static void __init ar7_init_env(struct env_var *env)
+{
+ int i;
+ struct psbl_rec *psbl = (struct psbl_rec *)(KSEG1ADDR(0x14000300));
+ void *psp_env = (void *)KSEG1ADDR(psbl->env_base);
+
+ if (strcmp(psp_env, psp_env_version) == 0) {
+ parse_psp_env(psp_env);
+ } else {
+ for (i = 0; i < MAX_ENTRY; i++, env++)
+ if (env->name)
+ add_adam2_var(env->name, env->value);
+ }
+}
+
+static void __init console_config(void)
+{
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+ char console_string[40];
+ int baud = 0;
+ char parity = '\0', bits = '\0', flow = '\0';
+ char *s, *p;
+
+ if (strstr(prom_getcmdline(), "console="))
+ return;
+
+#ifdef CONFIG_KGDB
+ if (!strstr(prom_getcmdline(), "nokgdb")) {
+ strcat(prom_getcmdline(), " console=kgdb");
+ kgdb_enabled = 1;
+ return;
+ }
+#endif
+
+ if ((s = prom_getenv("modetty0"))) {
+ baud = simple_strtoul(s, &p, 10);
+ s = p;
+ if (*s == ',') s++;
+ if (*s) parity = *s++;
+ if (*s == ',') s++;
+ if (*s) bits = *s++;
+ if (*s == ',') s++;
+ if (*s == 'h') flow = 'r';
+ }
+
+ if (baud == 0)
+ baud = 38400;
+ if (parity != 'n' && parity != 'o' && parity != 'e')
+ parity = 'n';
+ if (bits != '7' && bits != '8')
+ bits = '8';
+
+ if (flow == 'r')
+ sprintf(console_string, " console=ttyS0,%d%c%c%c", baud,
+ parity, bits, flow);
+ else
+ sprintf(console_string, " console=ttyS0,%d%c%c", baud, parity,
+ bits);
+ strcat(prom_getcmdline(), console_string);
+#endif
+}
+
+void __init prom_init(void)
+{
+ ar7_init_cmdline(fw_arg0, (char **)fw_arg1);
+ ar7_init_env((struct env_var *)fw_arg2);
+ console_config();
+}
+
+#define PORT(offset) (KSEG1ADDR(AR7_REGS_UART0 + (offset * 4)))
+static inline unsigned int serial_in(int offset)
+{
+ return readb((void *)PORT(offset));
+}
+
+static inline void serial_out(int offset, int value)
+{
+ writeb(value, (void *)PORT(offset));
+}
+
+char prom_getchar(void)
+{
+ while (!(serial_in(UART_LSR) & UART_LSR_DR));
+ return serial_in(UART_RX);
+}
+
+int prom_putchar(char c)
+{
+ while ((serial_in(UART_LSR) & UART_LSR_TEMT) == 0);
+ serial_out(UART_TX, c);
+ return 1;
+}
+
+/* from adm5120/prom.c */
+void prom_printf(char *fmt, ...)
+{
+ va_list args;
+ int l;
+ char *p, *buf_end;
+ char buf[1024];
+
+ va_start(args, fmt);
+ l = vsprintf(buf, fmt, args); /* hopefully i < sizeof(buf) */
+ va_end(args);
+
+ buf_end = buf + l;
+
+ for (p = buf; p < buf_end; p++) {
+ /* Crude cr/nl handling is better than none */
+ if (*p == '\n')
+ prom_putchar('\r');
+ prom_putchar(*p);
+ }
+}
+
+#ifdef CONFIG_KGDB
+int putDebugChar(char c)
+{
+ return prom_putchar(c);
+}
+
+char getDebugChar(void)
+{
+ return prom_getchar();
+}
+#endif
diff --git a/arch/mips/ar7/setup.c b/arch/mips/ar7/setup.c
new file mode 100644
index 0000000..793f37c
--- /dev/null
+++ b/arch/mips/ar7/setup.c
@@ -0,0 +1,106 @@
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ */
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/pm.h>
+
+#include <asm/mips-boards/prom.h>
+#include <asm/reboot.h>
+#include <asm/time.h>
+#include <asm/ar7/ar7.h>
+
+extern void ar7_time_init(void);
+static void ar7_machine_restart(char *command);
+static void ar7_machine_halt(void);
+static void ar7_machine_power_off(void);
+
+static void ar7_machine_restart(char *command)
+{
+ u32 *softres_reg = (u32 *)ioremap(AR7_REGS_RESET +
+ AR7_RESET_SOFTWARE, 1);
+ writel(1, softres_reg);
+}
+
+static void ar7_machine_halt(void)
+{
+ while (1);
+}
+
+static void ar7_machine_power_off(void)
+{
+ u32 *power_reg = (u32 *)ioremap(AR7_REGS_POWER, 1);
+ u32 power_state = readl(power_reg) | (3 << 30);
+ writel(power_state, power_reg);
+ ar7_machine_halt();
+}
+
+const char *get_system_type(void)
+{
+ u16 chip_id = ar7_chip_id();
+ switch (chip_id) {
+ case AR7_CHIP_7300:
+ return "TI AR7 (TNETD7300)";
+ case AR7_CHIP_7100:
+ return "TI AR7 (TNETD7100)";
+ case AR7_CHIP_7200:
+ return "TI AR7 (TNETD7200)";
+ default:
+ return "TI AR7 (Unknown)";
+ }
+}
+
+static int __init ar7_init_console(void)
+{
+ return 0;
+}
+
+/*
+ * Initializes basic routines and structures pointers, memory size (as
+ * given by the bios and saves the command line.
+ */
+
+extern void ar7_init_clocks(void);
+
+void __init plat_mem_setup(void)
+{
+ unsigned long io_base;
+
+ _machine_restart = ar7_machine_restart;
+ _machine_halt = ar7_machine_halt;
+ pm_power_off = ar7_machine_power_off;
+ board_time_init = ar7_time_init;
+ panic_timeout = 3;
+
+ io_base = (unsigned long)ioremap(AR7_REGS_BASE, 0x10000);
+ if (!io_base) panic("Can't remap IO base!\n");
+ set_io_port_base(io_base);
+
+ prom_meminit();
+ ar7_init_clocks();
+
+ ioport_resource.start = 0;
+ ioport_resource.end = ~0;
+ iomem_resource.start = 0;
+ iomem_resource.end = ~0;
+
+ printk(KERN_INFO "%s, ID: 0x%04x, Revision: 0x%02x\n",
+ get_system_type(),
+ ar7_chip_id(), ar7_chip_rev());
+}
+
+console_initcall(ar7_init_console);
diff --git a/arch/mips/ar7/time.c b/arch/mips/ar7/time.c
new file mode 100644
index 0000000..4be2895
--- /dev/null
+++ b/arch/mips/ar7/time.c
@@ -0,0 +1,32 @@
+/*
+ * Carsten Langgaard, carstenl@mips.com
+ * Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
+ *
+ * This program is free software; you can distribute it and/or modify it
+ * under the terms of the GNU General Public License (Version 2) as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
+ * for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * Setting up the clock on the MIPS boards.
+ */
+
+#include <asm/time.h>
+#include <asm/ar7/ar7.h>
+
+void __init ar7_time_init(void)
+{
+ mips_hpt_frequency = ar7_cpu_freq() / 2;
+}
+
+void __init plat_timer_setup(struct irqaction *irq)
+{
+ setup_irq(7, irq);
+}
diff --git a/arch/mips/kernel/traps.c b/arch/mips/kernel/traps.c
index 632bce1..3795c06 100644
--- a/arch/mips/kernel/traps.c
+++ b/arch/mips/kernel/traps.c
@@ -1076,9 +1076,22 @@ void *set_except_vector(int n, void *addr)
exception_handlers[n] = handler;
if (n == 0 && cpu_has_divec) {
- *(u32 *)(ebase + 0x200) = 0x08000000 |
- (0x03ffffff & (handler >> 2));
- flush_icache_range(ebase + 0x200, ebase + 0x204);
+ if ((handler ^ (ebase + 4)) & 0xfc000000) {
+ /* lui k0, 0x0000 */
+ *(u32 *)(ebase + 0x200) = 0x3c1a0000 | (handler >> 16);
+ /* ori k0, 0x0000 */
+ *(u32 *)(ebase + 0x204) =
+ 0x375a0000 | (handler & 0xffff);
+ /* jr k0 */
+ *(u32 *)(ebase + 0x208) = 0x03400008;
+ /* nop */
+ *(u32 *)(ebase + 0x20C) = 0x00000000;
+ flush_icache_range(ebase + 0x200, ebase + 0x210);
+ } else {
+ *(volatile u32 *)(ebase + 0x200) =
+ 0x08000000 | (0x03ffffff & (handler >> 2));
+ flush_icache_range(ebase + 0x200, ebase + 0x204);
+ }
}
return (void *)old_handler;
}
diff --git a/include/asm-mips/ar7/ar7.h b/include/asm-mips/ar7/ar7.h
new file mode 100644
index 0000000..4f90eb1
--- /dev/null
+++ b/include/asm-mips/ar7/ar7.h
@@ -0,0 +1,169 @@
+/*
+ * Copyright (C) 2006, 2007 Felix Fietkau, Eugene Konev
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef __AR7_H__
+#define __AR7_H__
+
+#include <linux/delay.h>
+#include <asm/addrspace.h>
+#include <linux/io.h>
+
+#define AR7_REGS_BASE 0x08610000
+
+#define AR7_REGS_MAC0 (AR7_REGS_BASE + 0x0000)
+#define AR7_REGS_GPIO (AR7_REGS_BASE + 0x0900)
+/* 0x08610A00 - 0x08610BFF (512 bytes, 128 bytes / clock) */
+#define AR7_REGS_POWER (AR7_REGS_BASE + 0x0a00)
+#define AR7_REGS_UART0 (AR7_REGS_BASE + 0x0e00)
+#define AR7_REGS_USB (AR7_REGS_BASE + 0x1200)
+#define AR7_REGS_RESET (AR7_REGS_BASE + 0x1600)
+#define AR7_REGS_VLYNQ0 (AR7_REGS_BASE + 0x1800)
+#define AR7_REGS_DCL (AR7_REGS_BASE + 0x1a00)
+#define AR7_REGS_VLYNQ1 (AR7_REGS_BASE + 0x1c00)
+#define AR7_REGS_MDIO (AR7_REGS_BASE + 0x1e00)
+#define AR7_REGS_IRQ (AR7_REGS_BASE + 0x2400)
+#define AR7_REGS_MAC1 (AR7_REGS_BASE + 0x2800)
+
+#define AR7_REGS_WDT (AR7_REGS_BASE + 0x1f00)
+#define UR8_REGS_WDT (AR7_REGS_BASE + 0x0b00)
+#define UR8_REGS_UART1 (AR7_REGS_BASE + 0x0f00)
+
+#define AR7_RESET_PEREPHERIAL 0x0
+#define AR7_RESET_SOFTWARE 0x4
+#define AR7_RESET_STATUS 0x8
+
+#define AR7_RESET_BIT_CPMAC_LO 17
+#define AR7_RESET_BIT_CPMAC_HI 21
+#define AR7_RESET_BIT_MDIO 22
+#define AR7_RESET_BIT_EPHY 26
+
+/* GPIO control registers */
+#define AR7_GPIO_INPUT 0x0
+#define AR7_GPIO_OUTPUT 0x4
+#define AR7_GPIO_DIR 0x8
+#define AR7_GPIO_ENABLE 0xc
+
+#define AR7_CHIP_7100 0x18
+#define AR7_CHIP_7200 0x2b
+#define AR7_CHIP_7300 0x05
+
+/* Interrupts */
+#define AR7_IRQ_UART0 15
+#define AR7_IRQ_UART1 16
+
+/* Clocks */
+#define AR7_AFE_CLOCK 35328000
+#define AR7_REF_CLOCK 25000000
+#define AR7_XTAL_CLOCK 24000000
+
+struct plat_cpmac_data {
+ int reset_bit;
+ int power_bit;
+ u32 phy_mask;
+ char dev_addr[6];
+};
+
+struct plat_dsl_data {
+ int reset_bit_dsl;
+ int reset_bit_sar;
+};
+
+extern int ar7_cpu_clock, ar7_bus_clock, ar7_dsp_clock;
+
+static inline u16 ar7_chip_id(void)
+{
+ return readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) & 0xffff;
+}
+
+static inline u8 ar7_chip_rev(void)
+{
+ return (readl((void *)KSEG1ADDR(AR7_REGS_GPIO + 0x14)) >> 16) & 0xff;
+}
+
+static inline int ar7_cpu_freq(void)
+{
+ return ar7_cpu_clock;
+}
+
+static inline int ar7_bus_freq(void)
+{
+ return ar7_bus_clock;
+}
+
+static inline int ar7_vbus_freq(void)
+{
+ return ar7_bus_clock / 2;
+}
+#define ar7_cpmac_freq ar7_vbus_freq
+
+static inline int ar7_dsp_freq(void)
+{
+ return ar7_dsp_clock;
+}
+
+static inline int ar7_has_high_cpmac(void)
+{
+ u16 chip_id = ar7_chip_id();
+ switch (chip_id) {
+ case AR7_CHIP_7100:
+ case AR7_CHIP_7200:
+ return 0;
+ default:
+ return 1;
+ }
+}
+#define ar7_has_high_vlynq ar7_has_high_cpmac
+#define ar7_has_second_uart ar7_has_high_cpmac
+
+static inline void ar7_device_enable(u32 bit)
+{
+ void *reset_reg =
+ (void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL);
+ writel(readl(reset_reg) | (1 << bit), reset_reg);
+ mdelay(20);
+}
+
+static inline void ar7_device_disable(u32 bit)
+{
+ void *reset_reg =
+ (void *)KSEG1ADDR(AR7_REGS_RESET + AR7_RESET_PEREPHERIAL);
+ writel(readl(reset_reg) & ~(1 << bit), reset_reg);
+ mdelay(20);
+}
+
+static inline void ar7_device_reset(u32 bit)
+{
+ ar7_device_disable(bit);
+ ar7_device_enable(bit);
+}
+
+static inline void ar7_device_on(u32 bit)
+{
+ void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+ writel(readl(power_reg) | (1 << bit), power_reg);
+ mdelay(20);
+}
+
+static inline void ar7_device_off(u32 bit)
+{
+ void *power_reg = (void *)KSEG1ADDR(AR7_REGS_POWER);
+ writel(readl(power_reg) & ~(1 << bit), power_reg);
+ mdelay(20);
+}
+
+#endif /* __AR7_H__ */
diff --git a/include/asm-mips/ar7/gpio.h b/include/asm-mips/ar7/gpio.h
new file mode 100644
index 0000000..4fe9496
--- /dev/null
+++ b/include/asm-mips/ar7/gpio.h
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2007 Florian Fainelli <florian@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef __AR7_GPIO_H__
+#define __AR7_GPIO_H__
+#include <asm/ar7/ar7.h>
+
+#define AR7_GPIO_MAX 32
+
+extern int gpio_request(unsigned gpio, const char *label);
+extern void gpio_free(unsigned gpio);
+
+/* Common GPIO layer */
+static inline int gpio_get_value(unsigned gpio)
+{
+ void __iomem *gpio_in =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_INPUT);
+
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ return ((readl(gpio_in) & (1 << gpio)) != 0);
+}
+
+static inline void gpio_set_value(unsigned gpio, int value)
+{
+ void __iomem *gpio_out =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_OUTPUT);
+ volatile unsigned tmp;
+
+ if (gpio >= AR7_GPIO_MAX)
+ return;
+
+ tmp = readl(gpio_out) & ~(1 << gpio);
+ if (value)
+ tmp |= 1 << gpio;
+ writel(tmp, gpio_out);
+}
+
+static inline int gpio_direction_input(unsigned gpio)
+{
+ void __iomem *gpio_dir =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR);
+
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ writel(readl(gpio_dir) | (1 << gpio), gpio_dir);
+
+ return 0;
+}
+
+static inline int gpio_direction_output(unsigned gpio, int value)
+{
+ void __iomem *gpio_dir =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_DIR);
+
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ gpio_set_value(gpio, value);
+ writel(readl(gpio_dir) & ~(1 << gpio), gpio_dir);
+
+ return 0;
+}
+
+static inline int gpio_to_irq(unsigned gpio)
+{
+ return -EINVAL;
+}
+
+static inline int irq_to_gpio(unsigned irq)
+{
+ return -EINVAL;
+}
+
+/* Board specific GPIO functions */
+static inline int ar7_gpio_enable(unsigned gpio)
+{
+ void __iomem *gpio_en =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE);
+
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ writel(readl(gpio_en) | (1 << gpio), gpio_en);
+
+ return 0;
+}
+
+static inline int ar7_gpio_disable(unsigned gpio)
+{
+ void __iomem *gpio_en =
+ (void __iomem *)KSEG1ADDR(AR7_REGS_GPIO + AR7_GPIO_ENABLE);
+
+ if (gpio >= AR7_GPIO_MAX)
+ return -EINVAL;
+
+ writel(readl(gpio_en) & ~(1 << gpio), gpio_en);
+
+ return 0;
+}
+
+#include <asm-generic/gpio.h>
+
+#endif
diff --git a/include/asm-mips/ar7/irq.h b/include/asm-mips/ar7/irq.h
new file mode 100644
index 0000000..39e9757
--- /dev/null
+++ b/include/asm-mips/ar7/irq.h
@@ -0,0 +1,16 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Shamelessly copied from asm-mips/mach-emma2rh/
+ * Copyright (C) 2003 by Ralf Baechle
+ */
+#ifndef __ASM_AR7_IRQ_H
+#define __ASM_AR7_IRQ_H
+
+#define NR_IRQS 256
+
+#include_next <irq.h>
+
+#endif /* __ASM_AR7_IRQ_H */
diff --git a/include/asm-mips/ar7/prom.h b/include/asm-mips/ar7/prom.h
new file mode 100644
index 0000000..62d7d5c
--- /dev/null
+++ b/include/asm-mips/ar7/prom.h
@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2006, 2007 Florian Fainelli <florian@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef __PROM_H__
+#define __PROM_H__
+
+extern char *prom_getenv(char *name);
+extern void prom_printf(char *fmt, ...);
+
+#endif /* __PROM_H__ */
diff --git a/include/asm-mips/ar7/spaces.h b/include/asm-mips/ar7/spaces.h
new file mode 100644
index 0000000..f4d1237
--- /dev/null
+++ b/include/asm-mips/ar7/spaces.h
@@ -0,0 +1,32 @@
+/*
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive
+ * for more details.
+ *
+ * Copyright (C) 1994 - 1999, 2000, 03, 04 Ralf Baechle
+ * Copyright (C) 2000, 2002 Maciej W. Rozycki
+ * Copyright (C) 1990, 1999, 2000 Silicon Graphics, Inc.
+ */
+#ifndef _ASM_AR7_SPACES_H
+#define _ASM_AR7_SPACES_H
+
+#define CAC_BASE 0x80000000
+#define IO_BASE 0xa0000000
+#define UNCAC_BASE 0xa0000000
+#define MAP_BASE 0xc0000000
+
+/*
+ * This handles the memory map.
+ * We handle pages at KSEG0 for kernels with 32 bit address space.
+ */
+#define PAGE_OFFSET 0x94000000UL
+#define PHYS_OFFSET 0x14000000UL
+
+/*
+ * Memory above this physical address will be considered highmem.
+ */
+#ifndef HIGHMEM_START
+#define HIGHMEM_START 0x40000000UL
+#endif
+
+#endif /* __ASM_AR7_SPACES_H */
diff --git a/include/asm-mips/page.h b/include/asm-mips/page.h
index d2ea983..8fda483 100644
--- a/include/asm-mips/page.h
+++ b/include/asm-mips/page.h
@@ -184,8 +184,10 @@ typedef struct { unsigned long pgprot; } pgprot_t;
#define VM_DATA_DEFAULT_FLAGS (VM_READ | VM_WRITE | VM_EXEC | \
VM_MAYREAD | VM_MAYWRITE | VM_MAYEXEC)
-#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE)
-#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET)
+#define UNCAC_ADDR(addr) ((addr) - PAGE_OFFSET + UNCAC_BASE + \
+ PHYS_OFFSET)
+#define CAC_ADDR(addr) ((addr) - UNCAC_BASE + PAGE_OFFSET - \
+ PHYS_OFFSET)
#include <asm-generic/memory_model.h>
#include <asm-generic/page.h>
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH][MIPS][2/6] AR7: VLYNQ bus
2007-10-11 0:48 [PATCH][MIPS][0/6] AR7: AR7 strikes back Matteo Croce
2007-10-11 0:50 ` [PATCH][MIPS][1/6] AR7: core support Matteo Croce
@ 2007-10-11 0:54 ` Matteo Croce
2007-10-11 0:55 ` [PATCH][MIPS][3/6] AR7: mtd partition map Matteo Croce
` (4 subsequent siblings)
6 siblings, 0 replies; 8+ messages in thread
From: Matteo Croce @ 2007-10-11 0:54 UTC (permalink / raw)
To: linux-mips; +Cc: Eugene Konev, Andrew Morton
Support for the Texas Instrument VLYNQ interconnect bus
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
diff --git a/drivers/vlynq/Kconfig b/drivers/vlynq/Kconfig
new file mode 100644
index 0000000..2c8ffe0
--- /dev/null
+++ b/drivers/vlynq/Kconfig
@@ -0,0 +1,13 @@
+menu "TI VLYNQ"
+
+config VLYNQ
+ bool "TI VLYNQ bus support"
+ depends on AR7 && EXPERIMENTAL
+ help
+ Support for the TI VLYNQ bus
+
+ The module will be called vlynq
+
+ If unsure, say N
+
+endmenu
diff --git a/drivers/vlynq/Makefile b/drivers/vlynq/Makefile
new file mode 100644
index 0000000..b3f6114
--- /dev/null
+++ b/drivers/vlynq/Makefile
@@ -0,0 +1,5 @@
+#
+# Makefile for kernel vlynq drivers
+#
+
+obj-$(CONFIG_VLYNQ) += vlynq.o
diff --git a/drivers/vlynq/vlynq.c b/drivers/vlynq/vlynq.c
new file mode 100644
index 0000000..0dd6c18
--- /dev/null
+++ b/drivers/vlynq/vlynq.c
@@ -0,0 +1,670 @@
+/*
+ * Copyright (C) 2006, 2007 OpenWrt.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/io.h>
+
+#include <linux/vlynq.h>
+
+#define VLYNQ_CTRL_PM_ENABLE 0x80000000
+#define VLYNQ_CTRL_CLOCK_INT 0x00008000
+#define VLYNQ_CTRL_CLOCK_DIV(x) (((x) & 7) << 16)
+#define VLYNQ_CTRL_INT_LOCAL 0x00004000
+#define VLYNQ_CTRL_INT_ENABLE 0x00002000
+#define VLYNQ_CTRL_INT_VECTOR(x) (((x) & 0x1f) << 8)
+#define VLYNQ_CTRL_INT2CFG 0x00000080
+#define VLYNQ_CTRL_RESET 0x00000001
+
+#define VLYNQ_INT_OFFSET 0x00000014
+#define VLYNQ_REMOTE_OFFSET 0x00000080
+
+#define VLYNQ_STATUS_LINK 0x00000001
+#define VLYNQ_STATUS_LERROR 0x00000080
+#define VLYNQ_STATUS_RERROR 0x00000100
+
+#define VINT_ENABLE 0x00000100
+#define VINT_TYPE_EDGE 0x00000080
+#define VINT_LEVEL_LOW 0x00000040
+#define VINT_VECTOR(x) ((x) & 0x1f)
+#define VINT_OFFSET(irq) (8 * ((irq) % 4))
+
+#define VLYNQ_AUTONEGO_V2 0x00010000
+
+struct vlynq_regs {
+ u32 revision;
+ u32 control;
+ u32 status;
+ u32 int_prio;
+ u32 int_status;
+ u32 int_pending;
+ u32 int_ptr;
+ u32 tx_offset;
+ struct vlynq_mapping rx_mapping[4];
+ u32 chip;
+ u32 autonego;
+ u32 unused[6];
+ u32 int_device[8];
+} __attribute__ ((packed));
+
+#define vlynq_reg_read(reg) readl(&(reg))
+#define vlynq_reg_write(reg, val) writel(val, &(reg))
+
+static int __vlynq_enable_device(struct vlynq_device *dev);
+
+#ifdef VLYNQ_DEBUG
+static void vlynq_dump_regs(struct vlynq_device *dev)
+{
+ int i;
+ printk(KERN_DEBUG "VLYNQ local=%p remote=%p\n",
+ dev->local, dev->remote);
+ for (i = 0; i < 32; i++) {
+ printk(KERN_DEBUG "VLYNQ: local %d: %08x\n",
+ i + 1, ((u32 *)dev->local)[i]);
+ printk(KERN_DEBUG "VLYNQ: remote %d: %08x\n",
+ i + 1, ((u32 *)dev->remote)[i]);
+ }
+}
+
+static void vlynq_dump_mem(u32 *base, int count)
+{
+ int i;
+ for (i = 0; i < (count + 3) / 4; i++) {
+ if (i % 4 == 0) printk(KERN_DEBUG "\nMEM[0x%04x]:", i * 4);
+ printk(KERN_DEBUG " 0x%08x", *(base + i));
+ }
+ printk(KERN_DEBUG "\n");
+}
+#endif
+
+int vlynq_linked(struct vlynq_device *dev)
+{
+ int i;
+
+ for (i = 0; i < 100; i++)
+ if (vlynq_reg_read(dev->local->status) & VLYNQ_STATUS_LINK)
+ return 1;
+ else
+ cpu_relax();
+
+ return 0;
+}
+
+static void vlynq_irq_unmask(unsigned int irq)
+{
+ u32 val;
+ struct vlynq_device *dev = get_irq_chip_data(irq);
+ int virq;
+
+ BUG_ON(!dev);
+ virq = irq - dev->irq_start;
+ val = vlynq_reg_read(dev->remote->int_device[virq >> 2]);
+ val |= (VINT_ENABLE | virq) << VINT_OFFSET(virq);
+ vlynq_reg_write(dev->remote->int_device[virq >> 2], val);
+}
+
+static void vlynq_irq_mask(unsigned int irq)
+{
+ u32 val;
+ struct vlynq_device *dev = get_irq_chip_data(irq);
+ int virq;
+
+ BUG_ON(!dev);
+ virq = irq - dev->irq_start;
+ val = vlynq_reg_read(dev->remote->int_device[virq >> 2]);
+ val &= ~(VINT_ENABLE << VINT_OFFSET(virq));
+ vlynq_reg_write(dev->remote->int_device[virq >> 2], val);
+}
+
+static int vlynq_irq_type(unsigned int irq, unsigned int flow_type)
+{
+ u32 val;
+ struct vlynq_device *dev = get_irq_chip_data(irq);
+ int virq;
+
+ BUG_ON(!dev);
+ virq = irq - dev->irq_start;
+ val = vlynq_reg_read(dev->remote->int_device[virq >> 2]);
+ switch (flow_type & IRQ_TYPE_SENSE_MASK) {
+ case IRQ_TYPE_EDGE_RISING:
+ case IRQ_TYPE_EDGE_FALLING:
+ case IRQ_TYPE_EDGE_BOTH:
+ val |= VINT_TYPE_EDGE << VINT_OFFSET(virq);
+ val &= ~(VINT_LEVEL_LOW << VINT_OFFSET(virq));
+ break;
+ case IRQ_TYPE_LEVEL_HIGH:
+ val &= ~(VINT_TYPE_EDGE << VINT_OFFSET(virq));
+ val &= ~(VINT_LEVEL_LOW << VINT_OFFSET(virq));
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ val &= ~(VINT_TYPE_EDGE << VINT_OFFSET(virq));
+ val |= VINT_LEVEL_LOW << VINT_OFFSET(virq);
+ break;
+ default:
+ return -EINVAL;
+ }
+ vlynq_reg_write(dev->remote->int_device[virq >> 2], val);
+ return 0;
+}
+
+static void vlynq_local_ack(unsigned int irq)
+{
+ struct vlynq_device *dev = get_irq_chip_data(irq);
+ u32 status = vlynq_reg_read(dev->local->status);
+ if (printk_ratelimit())
+ printk(KERN_DEBUG "%s: local status: 0x%08x\n",
+ dev->dev.bus_id, status);
+ vlynq_reg_write(dev->local->status, status);
+}
+
+static void vlynq_remote_ack(unsigned int irq)
+{
+ struct vlynq_device *dev = get_irq_chip_data(irq);
+ u32 status = vlynq_reg_read(dev->remote->status);
+ if (printk_ratelimit())
+ printk(KERN_DEBUG "%s: remote status: 0x%08x\n",
+ dev->dev.bus_id, status);
+ vlynq_reg_write(dev->remote->status, status);
+}
+
+static irqreturn_t vlynq_irq(int irq, void *dev_id)
+{
+ struct vlynq_device *dev = dev_id;
+ u32 status;
+ int virq = 0;
+
+ status = vlynq_reg_read(dev->local->int_status);
+ vlynq_reg_write(dev->local->int_status, status);
+
+ if (unlikely(!status))
+ spurious_interrupt();
+
+ while (status) {
+ if (status & 1)
+ do_IRQ(dev->irq_start + virq);
+ status >>= 1;
+ virq++;
+ }
+
+ return IRQ_HANDLED;
+}
+
+static struct irq_chip vlynq_irq_chip = {
+ .name = "vlynq",
+ .unmask = vlynq_irq_unmask,
+ .mask = vlynq_irq_mask,
+ .set_type = vlynq_irq_type,
+};
+
+static struct irq_chip vlynq_local_chip = {
+ .name = "vlynq local error",
+ .unmask = vlynq_irq_unmask,
+ .mask = vlynq_irq_mask,
+ .ack = vlynq_local_ack,
+};
+
+static struct irq_chip vlynq_remote_chip = {
+ .name = "vlynq local error",
+ .unmask = vlynq_irq_unmask,
+ .mask = vlynq_irq_mask,
+ .ack = vlynq_remote_ack,
+};
+
+static int vlynq_setup_irq(struct vlynq_device *dev)
+{
+ u32 val;
+ int i, virq;
+
+ if (dev->local_irq == dev->remote_irq) {
+ printk(KERN_ERR
+ "%s: local vlynq irq should be different from remote\n",
+ dev->dev.bus_id);
+ return -EINVAL;
+ }
+
+ /* Clear local and remote error bits */
+ vlynq_reg_write(dev->local->status, vlynq_reg_read(dev->local->status));
+ vlynq_reg_write(dev->remote->status,
+ vlynq_reg_read(dev->remote->status));
+
+ /* Now setup interrupts */
+ val = VLYNQ_CTRL_INT_VECTOR(dev->local_irq);
+ val |= VLYNQ_CTRL_INT_ENABLE | VLYNQ_CTRL_INT_LOCAL |
+ VLYNQ_CTRL_INT2CFG;
+ val |= vlynq_reg_read(dev->local->control);
+ vlynq_reg_write(dev->local->int_ptr, VLYNQ_INT_OFFSET);
+ vlynq_reg_write(dev->local->control, val);
+
+ val = VLYNQ_CTRL_INT_VECTOR(dev->remote_irq);
+ val |= VLYNQ_CTRL_INT_ENABLE;
+ val |= vlynq_reg_read(dev->remote->control);
+ vlynq_reg_write(dev->remote->int_ptr, VLYNQ_INT_OFFSET);
+ vlynq_reg_write(dev->remote->control, val);
+
+ for (i = dev->irq_start; i <= dev->irq_end; i++) {
+ virq = i - dev->irq_start;
+ if (virq == dev->local_irq) {
+ set_irq_chip_and_handler(i, &vlynq_local_chip,
+ handle_level_irq);
+ set_irq_chip_data(i, dev);
+ } else if (virq == dev->remote_irq) {
+ set_irq_chip_and_handler(i, &vlynq_remote_chip,
+ handle_level_irq);
+ set_irq_chip_data(i, dev);
+ } else {
+ set_irq_chip_and_handler(i, &vlynq_irq_chip,
+ handle_simple_irq);
+ set_irq_chip_data(i, dev);
+ vlynq_reg_write(dev->remote->int_device[virq >> 2], 0);
+ }
+ }
+
+ if (request_irq(dev->irq, vlynq_irq, IRQF_SHARED, "vlynq", dev)) {
+ printk(KERN_ERR "%s: request_irq failed\n", dev->dev.bus_id);
+ return -EAGAIN;
+ }
+
+ return 0;
+}
+
+static void vlynq_device_release(struct device *dev)
+{
+ struct vlynq_device *vdev = to_vlynq_device(dev);
+ kfree(vdev);
+}
+
+static int vlynq_device_match(struct device *dev,
+ struct device_driver *drv)
+{
+ struct vlynq_device *vdev = to_vlynq_device(dev);
+ struct vlynq_driver *vdrv = to_vlynq_driver(drv);
+ struct plat_vlynq_ops *ops = dev->platform_data;
+ struct vlynq_device_id *ids = vdrv->id_table;
+ u32 id = 0;
+ int result;
+
+ while (ids->id) {
+ vdev->divisor = ids->divisor;
+ result = __vlynq_enable_device(vdev);
+ if (result == 0) {
+ id = vlynq_reg_read(vdev->remote->chip);
+ ops->off(vdev);
+ if (ids->id == id) {
+ vlynq_set_drvdata(vdev, ids);
+ return 1;
+ }
+ }
+ ids++;
+ }
+ return 0;
+}
+
+static int vlynq_device_probe(struct device *dev)
+{
+ struct vlynq_device *vdev = to_vlynq_device(dev);
+ struct vlynq_driver *drv = to_vlynq_driver(dev->driver);
+ struct vlynq_device_id *id = vlynq_get_drvdata(vdev);
+ int result = -ENODEV;
+
+ get_device(dev);
+ if (drv && drv->probe)
+ result = drv->probe(vdev, id);
+ if (result)
+ put_device(dev);
+ return result;
+}
+
+static int vlynq_device_remove(struct device *dev)
+{
+ struct vlynq_driver *drv = to_vlynq_driver(dev->driver);
+ if (drv && drv->remove)
+ drv->remove(to_vlynq_device(dev));
+ put_device(dev);
+ return 0;
+}
+
+int __vlynq_register_driver(struct vlynq_driver *driver, struct module *owner)
+{
+ driver->driver.name = driver->name;
+ driver->driver.bus = &vlynq_bus_type;
+ return driver_register(&driver->driver);
+}
+EXPORT_SYMBOL(__vlynq_register_driver);
+
+void vlynq_unregister_driver(struct vlynq_driver *driver)
+{
+ driver_unregister(&driver->driver);
+}
+EXPORT_SYMBOL(vlynq_unregister_driver);
+
+static int __vlynq_enable_device(struct vlynq_device *dev)
+{
+ int i, result;
+ struct plat_vlynq_ops *ops = dev->dev.platform_data;
+
+ result = ops->on(dev);
+ if (result)
+ return result;
+
+ switch (dev->divisor) {
+ case vlynq_div_auto:
+ /* Only try locally supplied clock, others cause problems */
+ vlynq_reg_write(dev->remote->control, 0);
+ for (i = vlynq_ldiv1; i <= vlynq_ldiv8; i++) {
+ vlynq_reg_write(dev->local->control,
+ VLYNQ_CTRL_CLOCK_INT |
+ VLYNQ_CTRL_CLOCK_DIV(i - vlynq_ldiv1));
+ if (vlynq_linked(dev)) {
+ printk(KERN_DEBUG
+ "%s: using local clock divisor %d\n",
+ dev->dev.bus_id, i - vlynq_ldiv1 + 1);
+ dev->divisor = i;
+ return 0;
+ }
+ }
+ case vlynq_ldiv1: case vlynq_ldiv2: case vlynq_ldiv3: case vlynq_ldiv4:
+ case vlynq_ldiv5: case vlynq_ldiv6: case vlynq_ldiv7: case vlynq_ldiv8:
+ vlynq_reg_write(dev->remote->control, 0);
+ vlynq_reg_write(dev->local->control,
+ VLYNQ_CTRL_CLOCK_INT |
+ VLYNQ_CTRL_CLOCK_DIV(dev->divisor -
+ vlynq_ldiv1));
+ if (vlynq_linked(dev)) {
+ printk(KERN_DEBUG
+ "%s: using local clock divisor %d\n",
+ dev->dev.bus_id, dev->divisor - vlynq_ldiv1 + 1);
+ return 0;
+ }
+ break;
+ case vlynq_rdiv1: case vlynq_rdiv2: case vlynq_rdiv3: case vlynq_rdiv4:
+ case vlynq_rdiv5: case vlynq_rdiv6: case vlynq_rdiv7: case vlynq_rdiv8:
+ vlynq_reg_write(dev->local->control, 0);
+ vlynq_reg_write(dev->remote->control,
+ VLYNQ_CTRL_CLOCK_INT |
+ VLYNQ_CTRL_CLOCK_DIV(dev->divisor -
+ vlynq_rdiv1));
+ if (vlynq_linked(dev)) {
+ printk(KERN_DEBUG
+ "%s: using remote clock divisor %d\n",
+ dev->dev.bus_id, dev->divisor - vlynq_rdiv1 + 1);
+ return 0;
+ }
+ break;
+ case vlynq_div_external:
+ vlynq_reg_write(dev->local->control, 0);
+ vlynq_reg_write(dev->remote->control, 0);
+ if (vlynq_linked(dev)) {
+ printk(KERN_DEBUG "%s: using external clock\n",
+ dev->dev.bus_id);
+ return 0;
+ }
+ break;
+ }
+
+ ops->off(dev);
+ return -ENODEV;
+}
+
+int vlynq_enable_device(struct vlynq_device *dev)
+{
+ struct plat_vlynq_ops *ops = dev->dev.platform_data;
+ int result = -ENODEV;
+
+ result = __vlynq_enable_device(dev);
+ if (result)
+ return result;
+
+ result = vlynq_setup_irq(dev);
+ if (result)
+ ops->off(dev);
+
+ dev->enabled = !result;
+ return result;
+}
+EXPORT_SYMBOL(vlynq_enable_device);
+
+
+void vlynq_disable_device(struct vlynq_device *dev)
+{
+ struct plat_vlynq_ops *ops = dev->dev.platform_data;
+
+ dev->enabled = 0;
+ free_irq(dev->irq, dev);
+ ops->off(dev);
+}
+EXPORT_SYMBOL(vlynq_disable_device);
+
+int vlynq_set_local_mapping(struct vlynq_device *dev, u32 tx_offset,
+ struct vlynq_mapping *mapping)
+{
+ int i;
+
+ if (!dev->enabled)
+ return -ENXIO;
+
+ vlynq_reg_write(dev->local->tx_offset, tx_offset);
+ for (i = 0; i < 4; i++) {
+ vlynq_reg_write(dev->local->rx_mapping[i].offset,
+ mapping[i].offset);
+ vlynq_reg_write(dev->local->rx_mapping[i].size,
+ mapping[i].size);
+ }
+ return 0;
+}
+EXPORT_SYMBOL(vlynq_set_local_mapping);
+
+int vlynq_set_remote_mapping(struct vlynq_device *dev, u32 tx_offset,
+ struct vlynq_mapping *mapping)
+{
+ int i;
+
+ if (!dev->enabled)
+ return -ENXIO;
+
+ vlynq_reg_write(dev->remote->tx_offset, tx_offset);
+ for (i = 0; i < 4; i++) {
+ vlynq_reg_write(dev->remote->rx_mapping[i].offset,
+ mapping[i].offset);
+ vlynq_reg_write(dev->remote->rx_mapping[i].size,
+ mapping[i].size);
+ }
+ return 0;
+}
+EXPORT_SYMBOL(vlynq_set_remote_mapping);
+
+int vlynq_set_local_irq(struct vlynq_device *dev, int virq)
+{
+ int irq = dev->irq_start + virq;
+ if (dev->enabled)
+ return -EBUSY;
+
+ if ((irq < dev->irq_start) || (irq > dev->irq_end))
+ return -EINVAL;
+
+ if (virq == dev->remote_irq)
+ return -EINVAL;
+
+ dev->local_irq = virq;
+
+ return 0;
+}
+EXPORT_SYMBOL(vlynq_set_local_irq);
+
+int vlynq_set_remote_irq(struct vlynq_device *dev, int virq)
+{
+ int irq = dev->irq_start + virq;
+ if (dev->enabled)
+ return -EBUSY;
+
+ if ((irq < dev->irq_start) || (irq > dev->irq_end))
+ return -EINVAL;
+
+ if (virq == dev->local_irq)
+ return -EINVAL;
+
+ dev->remote_irq = virq;
+
+ return 0;
+}
+EXPORT_SYMBOL(vlynq_set_remote_irq);
+
+static int vlynq_probe(struct platform_device *pdev)
+{
+ struct vlynq_device *dev;
+ struct resource *regs_res, *mem_res, *irq_res;
+ int len, result;
+
+ regs_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "regs");
+ if (!regs_res)
+ return -ENODEV;
+
+ mem_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mem");
+ if (!mem_res)
+ return -ENODEV;
+
+ irq_res = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "devirq");
+ if (!irq_res)
+ return -ENODEV;
+
+ dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+ if (!dev) {
+ printk(KERN_ERR
+ "vlynq: failed to allocate device structure\n");
+ return -ENOMEM;
+ }
+
+ dev->id = pdev->id;
+ dev->dev.bus = &vlynq_bus_type;
+ dev->dev.parent = &pdev->dev;
+ snprintf(dev->dev.bus_id, BUS_ID_SIZE, "vlynq%d", dev->id);
+ dev->dev.bus_id[BUS_ID_SIZE - 1] = 0;
+ dev->dev.platform_data = pdev->dev.platform_data;
+ dev->dev.release = vlynq_device_release;
+
+ dev->regs_start = regs_res->start;
+ dev->regs_end = regs_res->end;
+ dev->mem_start = mem_res->start;
+ dev->mem_end = mem_res->end;
+
+ len = regs_res->end - regs_res->start;
+ if (!request_mem_region(regs_res->start, len, dev->dev.bus_id)) {
+ printk(KERN_ERR "%s: Can't request vlynq registers\n",
+ dev->dev.bus_id);
+ result = -ENXIO;
+ goto fail_request;
+ }
+
+ dev->local = ioremap(regs_res->start, len);
+ if (!dev->local) {
+ printk(KERN_ERR "%s: Can't remap vlynq registers\n",
+ dev->dev.bus_id);
+ result = -ENXIO;
+ goto fail_remap;
+ }
+
+ dev->remote = (struct vlynq_regs *)((void *)dev->local +
+ VLYNQ_REMOTE_OFFSET);
+
+ dev->irq = platform_get_irq_byname(pdev, "irq");
+ dev->irq_start = irq_res->start;
+ dev->irq_end = irq_res->end;
+ dev->local_irq = dev->irq_end - dev->irq_start;
+ dev->remote_irq = dev->local_irq - 1;
+
+ if (device_register(&dev->dev))
+ goto fail_register;
+ platform_set_drvdata(pdev, dev);
+
+ printk(KERN_INFO "%s: regs 0x%p, irq %d, mem 0x%p\n",
+ dev->dev.bus_id, (void *)dev->regs_start, dev->irq,
+ (void *)dev->mem_start);
+
+ return 0;
+
+fail_register:
+ iounmap(dev->local);
+fail_remap:
+fail_request:
+ release_mem_region(regs_res->start, len);
+ kfree(dev);
+ return result;
+}
+
+static int vlynq_remove(struct platform_device *pdev)
+{
+ struct vlynq_device *dev = platform_get_drvdata(pdev);
+
+ device_unregister(&dev->dev);
+ iounmap(dev->local);
+ release_mem_region(dev->regs_start, dev->regs_end - dev->regs_start);
+
+ kfree(dev);
+
+ return 0;
+}
+
+static struct platform_driver vlynq_driver = {
+ .driver.name = "vlynq",
+ .probe = vlynq_probe,
+ .remove = __devexit_p(vlynq_remove),
+};
+
+struct bus_type vlynq_bus_type = {
+ .name = "vlynq",
+ .match = vlynq_device_match,
+ .probe = vlynq_device_probe,
+ .remove = vlynq_device_remove,
+};
+EXPORT_SYMBOL(vlynq_bus_type);
+
+static int __devinit vlynq_init(void)
+{
+ int res = 0;
+
+ res = bus_register(&vlynq_bus_type);
+ if (res)
+ goto fail_bus;
+
+ res = platform_driver_register(&vlynq_driver);
+ if (res)
+ goto fail_platform;
+
+ return 0;
+
+fail_platform:
+ bus_unregister(&vlynq_bus_type);
+fail_bus:
+ return res;
+}
+
+static void __devexit vlynq_exit(void)
+{
+ platform_driver_unregister(&vlynq_driver);
+ bus_unregister(&vlynq_bus_type);
+}
+
+module_init(vlynq_init);
+module_exit(vlynq_exit);
diff --git a/include/linux/vlynq.h b/include/linux/vlynq.h
new file mode 100644
index 0000000..b3f2474
--- /dev/null
+++ b/include/linux/vlynq.h
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2006, 2007 OpenWrt.org
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef __VLYNQ_H__
+#define __VLYNQ_H__
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/types.h>
+
+#define VLYNQ_NUM_IRQS 32
+
+struct vlynq_mapping {
+ u32 size;
+ u32 offset;
+};
+
+enum vlynq_divisor {
+ vlynq_div_auto = 0,
+ vlynq_ldiv1,
+ vlynq_ldiv2,
+ vlynq_ldiv3,
+ vlynq_ldiv4,
+ vlynq_ldiv5,
+ vlynq_ldiv6,
+ vlynq_ldiv7,
+ vlynq_ldiv8,
+ vlynq_rdiv1,
+ vlynq_rdiv2,
+ vlynq_rdiv3,
+ vlynq_rdiv4,
+ vlynq_rdiv5,
+ vlynq_rdiv6,
+ vlynq_rdiv7,
+ vlynq_rdiv8,
+ vlynq_div_external
+};
+
+struct vlynq_device_id {
+ u32 id;
+ enum vlynq_divisor divisor;
+ unsigned long driver_data;
+};
+
+struct vlynq_regs;
+struct vlynq_device {
+ u32 id;
+ int local_irq;
+ int remote_irq;
+ enum vlynq_divisor divisor;
+ u32 regs_start, regs_end;
+ u32 mem_start, mem_end;
+ u32 irq_start, irq_end;
+ int irq;
+ int enabled;
+ struct vlynq_regs *local;
+ struct vlynq_regs *remote;
+ struct device dev;
+};
+
+struct vlynq_driver {
+ char *name;
+ struct vlynq_device_id *id_table;
+ int (*probe)(struct vlynq_device *dev, struct vlynq_device_id *id);
+ void (*remove)(struct vlynq_device *dev);
+ struct device_driver driver;
+};
+
+struct plat_vlynq_ops {
+ int (*on)(struct vlynq_device *dev);
+ void (*off)(struct vlynq_device *dev);
+};
+
+static inline struct vlynq_driver *to_vlynq_driver(struct device_driver *drv)
+{
+ return container_of(drv, struct vlynq_driver, driver);
+}
+
+static inline struct vlynq_device *to_vlynq_device(struct device *device)
+{
+ return container_of(device, struct vlynq_device, dev);
+}
+
+extern struct bus_type vlynq_bus_type;
+
+extern int __vlynq_register_driver(struct vlynq_driver *driver,
+ struct module *owner);
+
+static inline int vlynq_register_driver(struct vlynq_driver *driver)
+{
+ return __vlynq_register_driver(driver, THIS_MODULE);
+}
+
+static inline void *vlynq_get_drvdata(struct vlynq_device *dev)
+{
+ return dev_get_drvdata(&dev->dev);
+}
+
+static inline void vlynq_set_drvdata(struct vlynq_device *dev, void *data)
+{
+ dev_set_drvdata(&dev->dev, data);
+}
+
+static inline u32 vlynq_mem_start(struct vlynq_device *dev)
+{
+ return dev->mem_start;
+}
+
+static inline u32 vlynq_mem_end(struct vlynq_device *dev)
+{
+ return dev->mem_end;
+}
+
+static inline u32 vlynq_mem_len(struct vlynq_device *dev)
+{
+ return dev->mem_end - dev->mem_start + 1;
+}
+
+static inline int vlynq_virq_to_irq(struct vlynq_device *dev, int virq)
+{
+ int irq = dev->irq_start + virq;
+ if ((irq < dev->irq_start) || (irq > dev->irq_end))
+ return -EINVAL;
+
+ return irq;
+}
+
+static inline int vlynq_irq_to_virq(struct vlynq_device *dev, int irq)
+{
+ if ((irq < dev->irq_start) || (irq > dev->irq_end))
+ return -EINVAL;
+
+ return irq - dev->irq_start;
+}
+
+extern void vlynq_unregister_driver(struct vlynq_driver *driver);
+extern int vlynq_enable_device(struct vlynq_device *dev);
+extern void vlynq_disable_device(struct vlynq_device *dev);
+extern int vlynq_set_local_mapping(struct vlynq_device *dev, u32 tx_offset,
+ struct vlynq_mapping *mapping);
+extern int vlynq_set_remote_mapping(struct vlynq_device *dev, u32 tx_offset,
+ struct vlynq_mapping *mapping);
+extern int vlynq_set_local_irq(struct vlynq_device *dev, int virq);
+extern int vlynq_set_remote_irq(struct vlynq_device *dev, int virq);
+
+#endif /* __VLYNQ_H__ */
^ permalink raw reply related [flat|nested] 8+ messages in thread