* Re: BCM36xx support.
2012-05-31 13:55 ` BCM36xx support Florian Fainelli
@ 2012-05-31 14:25 ` Rogier Wolff
0 siblings, 0 replies; 2+ messages in thread
From: Rogier Wolff @ 2012-05-31 14:25 UTC (permalink / raw)
To: Florian Fainelli; +Cc: Rogier Wolff, linux-kernel, linux-mips
Hi Florian,
On Thu, May 31, 2012 at 03:55:34PM +0200, Florian Fainelli wrote:
> First of all, you should have CC'd linux-mips, because that's where
> BCM63xx development happens.
As I'm not familiar with mips-development, I didn't know that.
> On Wednesday 18 April 2012 07:51:40 Rogier Wolff wrote:
> >
> > While working on SPI and I2C support for the BCM2835, I found the
> > BCM63xx SPI driver in the kernel. Turns out that this support
> > was partially merged:
> >
> > The support can only be enabled when BCM63xx configuration symbol
> > is defined which menuconfig lists as:
> >
> > Symbol: BCM63XX [=BCM63XX]
> > Type : unknown
> >
> > I'd say the definition of this is not possible through the normal
> > channels.
> >
> > And in the driver (drivers/spi/spi-bcm63xx.c) I see:
> >
> > #include <bcm63xx_dev_spi.h>
> >
> > but that file is not in the current git release.
>
> No, it did not make it for a reason I ignore, probably miscommunication.
>
> >
> > (some more googling has resulted in me finding out that I don't want
> > to know how the 63xx SPI controller works as it's for a MIPS processor
> > while the 2835 is ARM).
> And so? if the core is the same, just use it on your platform
> too. If you have a look at the architecture files, you will see that
> the various BCM63xx SoC have their internal registers shuffled but
> the SPI core is always software compatible, another set of registers
> can be added for BCM2835.
I expect the core to be very different because they are for different
processors. But of course if they are the same, a single driver would
be better.
However, with the header file missing, I can't find if the register
offsets are the same. That would be a hint that the module is the the
same.
Reading the driver I see lots "readb" and "writeb" calls. These
presumably read/write a byte. The '2835 module doesn't have any
byte-registers. All registers are 32bits. I consider this a further
hint that the modules are not the same.
I've read some of the code, and for instance, there seems to be a
limited-width register (3 or 4 bits) that specify the clock rate on
the bcm63xx. On the bcm2835 the clock is set by good chunk (15 bits
IIRC) of a 32-bit register which specifies the clock divisor. The core
clock runs at 250MHz, so I can specify clock rates at with 1:250
accuracy around 1MHz. (i.e. 1000000 Hz is possible as well as 1004000)
I consider this a further hint that the modules are not the same.
So with three of those hints I'll take the hint that they are not the
same, and concentrate on building a new driver for the bcm2835 (and
2708?)
Roger.
--
** R.E.Wolff@BitWizard.nl ** http://www.BitWizard.nl/ ** +31-15-2600998 **
** Delftechpark 26 2628 XH Delft, The Netherlands. KVK: 27239233 **
*-- BitWizard writes Linux device drivers for any device you may have! --*
The plan was simple, like my brother-in-law Phil. But unlike
Phil, this plan just might work.
^ permalink raw reply [flat|nested] 2+ messages in thread