* Getting Started ..... NOT
@ 1998-03-12 19:35 Tony C. Wu
1998-03-12 20:44 ` Eric Kimminau
1998-03-12 21:16 ` Alan Cox
0 siblings, 2 replies; 8+ messages in thread
From: Tony C. Wu @ 1998-03-12 19:35 UTC (permalink / raw)
To: linux
Hi,
After the 101st failure on getting sgi-linux to work on our poor SGI indy,
I decided to beg you guys for a clue. I used installer-0.10d and
root-be-0.03-cpio. I followed every step listed in the INSTALL that came
with installer-0.10d.
1. ./mke2fs /dev/dsk/dks0d2s0 ok
2. ./installer /dev/dsk/dks0d2s0 ok
3. MAKEDEV ok
4. cpio root-be-0.03-cpio ok
5. exit ok
6. ./e2fsck -fy /dev/dsk/dks0d2s0 fixed some errors, ok
7. gzip -d vmlinux-2.1.65.efs.gz /vmlinux ok
>> boot vmlinux root=/dev/sdb1 failed.
I tried every pre-compiled kernel that's in the pub/test dir of
ftp.linux.sgi.com pub/test, but all failed.
2.1.65 gave: bus error
2.1.72 gave: blank screen
2.1.72_NOSL: put me in repair fs mode, but i can't change anything.
It said it couldn't read superblock on /dev/sdb
Here's what hinv says about our indy.
---- HINV -------------------------------------------------------------
Iris Audio Processor: version A2 revision 4.1.0
1 100 MHZ IP22 Processor
FPU: MIPS R4600 Floating Point Coprocessor Revision: 2.0
CPU: MIPS R4600 Processor Chip Revision: 2.0
On-board serial ports: 2
On-board bi-directional parallel port
Data cache size: 16 Kbytes
Instruction cache size: 16 Kbytes
Main memory size: 64 Mbytes
Vino video: unit 0, revision 0, IndyCam not connected
Integral ISDN: Basic Rate Interface unit 0, revision 1.0
Integral Ethernet: ec0, version 1
Integral SCSI controller 0: Version WD33C93B, revision D
Disk drive: unit 2 on SCSI controller 0
Disk drive: unit 1 on SCSI controller 0
Graphics board: Indy 8-bit
---------------------------------------------------------------------
Any help is appreciated.
Thanks,
--
Tony C. Wu
System administrator Email: tonywu@life.nthu.edu.tw
Dept. of Life Sciences Voice: +886-3-574-2772
NTHU, Hsin-Chu, Taiwan Fax: +886-3-571-5934
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 19:35 Getting Started ..... NOT Tony C. Wu
@ 1998-03-12 20:44 ` Eric Kimminau
1998-03-12 21:20 ` Alex deVries
1998-03-12 21:16 ` Alan Cox
1 sibling, 1 reply; 8+ messages in thread
From: Eric Kimminau @ 1998-03-12 20:44 UTC (permalink / raw)
To: Tony C. Wu; +Cc: linux
Tony C. Wu wrote:
> 2.1.72_NOSL: put me in repair fs mode, but i can't change anything.
> It said it couldn't read superblock on /dev/sdb
Re-read the HOWTO wehere it tells you how to remount / read-write
Ive gotten this far as well. I then could ifconfig my ethernet interface
and add the necessary routing information to talk to the network, but I
couldn't ever actually get it to talk. I could ping myself but nothing
else. I assumed this was because I didn't have things like inetd, rc
scripts to start things, etc...
My next step was to then pull down all of the mips RPMS to the 1st disk
running linux, and I was going to then try to mount the first disk after
booting Linux off of the second disk - then installing all of the RPM's
- but I haven't gotten there yet.
It would be REALLY nice, if someone could take their installed system,
tar/cpio the whole ball of wax and put it up for download.
Eric.
--
---------1---------2---------3---------4---------5---------6---------7---------8
Eric Kimminau RTA/RSA
eak@detroit.sgi.com Silicon Graphics, Inc
Voice: (248) 848-4455 39001 West 12 Mile Rd.
Fax: (248) 848-5600 Farmington, MI 48331-2903
VNet Extension - 6-327-4455
"I speak my mind and no one else's."
http://www.dcs.ex.ac.uk/~aba/rsa/perl-rsa-sig.html
When confronted by a difficult problem, solve it by reducing
it to the question, "How would the Lone Ranger handle this?"
"I am the great supportfolio, do you have http?"
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 19:35 Getting Started ..... NOT Tony C. Wu
1998-03-12 20:44 ` Eric Kimminau
@ 1998-03-12 21:16 ` Alan Cox
1998-03-12 21:16 ` Alan Cox
1998-03-13 5:22 ` Tony C. Wu
1 sibling, 2 replies; 8+ messages in thread
From: Alan Cox @ 1998-03-12 21:16 UTC (permalink / raw)
To: Tony C. Wu; +Cc: linux
> 2.1.72_NOSL: put me in repair fs mode, but i can't change anything.
> It said it couldn't read superblock on /dev/sdb
Ok. The disk image expects to be /dev/sdb
do
mount -n -o remount,rw /dev/sdb1 /
vi /etc/fstab
change /dev/sdb to /dev/sdb1
exit
Best of luck
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 21:16 ` Alan Cox
@ 1998-03-12 21:16 ` Alan Cox
1998-03-13 5:22 ` Tony C. Wu
1 sibling, 0 replies; 8+ messages in thread
From: Alan Cox @ 1998-03-12 21:16 UTC (permalink / raw)
To: Tony C. Wu; +Cc: linux
> 2.1.72_NOSL: put me in repair fs mode, but i can't change anything.
> It said it couldn't read superblock on /dev/sdb
Ok. The disk image expects to be /dev/sdb
do
mount -n -o remount,rw /dev/sdb1 /
vi /etc/fstab
change /dev/sdb to /dev/sdb1
exit
Best of luck
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 20:44 ` Eric Kimminau
@ 1998-03-12 21:20 ` Alex deVries
1998-03-12 21:48 ` Eric Kimminau
0 siblings, 1 reply; 8+ messages in thread
From: Alex deVries @ 1998-03-12 21:20 UTC (permalink / raw)
To: Eric Kimminau; +Cc: Tony C. Wu, linux
On Thu, 12 Mar 1998, Eric Kimminau wrote:
>
> It would be REALLY nice, if someone could take their installed system,
> tar/cpio the whole ball of wax and put it up for download.
Uh, I could, but that's about 1GB uncompressed...
- Alex
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 21:20 ` Alex deVries
@ 1998-03-12 21:48 ` Eric Kimminau
0 siblings, 0 replies; 8+ messages in thread
From: Eric Kimminau @ 1998-03-12 21:48 UTC (permalink / raw)
To: Alex deVries; +Cc: Tony C. Wu, linux
Alex deVries wrote:
>
> On Thu, 12 Mar 1998, Eric Kimminau wrote:
> >
> > It would be REALLY nice, if someone could take their installed system,
> > tar/cpio the whole ball of wax and put it up for download.
>
> Uh, I could, but that's about 1GB uncompressed...
>
> - Alex
Tell me where to come get it :)
OK, lets re-define "whole ball of wax"
A functional distribution with X, network tools, normally used sys-admin
tools, a compiler and the source for the kernel plus a few odds and
ends. This should be "do-able" in 2-300MB, which I don't think would be
considered excessivly large.
Eric.
--
---------1---------2---------3---------4---------5---------6---------7---------8
Eric Kimminau RTA/RSA
eak@detroit.sgi.com Silicon Graphics, Inc
Voice: (248) 848-4455 39001 West 12 Mile Rd.
Fax: (248) 848-5600 Farmington, MI 48331-2903
VNet Extension - 6-327-4455
"I speak my mind and no one else's."
http://www.dcs.ex.ac.uk/~aba/rsa/perl-rsa-sig.html
When confronted by a difficult problem, solve it by reducing
it to the question, "How would the Lone Ranger handle this?"
"I am the great supportfolio, do you have http?"
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-12 21:16 ` Alan Cox
1998-03-12 21:16 ` Alan Cox
@ 1998-03-13 5:22 ` Tony C. Wu
1998-03-24 18:19 ` Francis M. J. Hsieh
1 sibling, 1 reply; 8+ messages in thread
From: Tony C. Wu @ 1998-03-13 5:22 UTC (permalink / raw)
To: Alan Cox; +Cc: linux
Ok. done that. I can successfully remount the / rw, but still, wont go any
further. I tested fsck manually, no matter what device I specified, it
always printed the same error and exited immediately. If I comment fsck
part, and boot directly, still wont go. So I think the root-be-0.03-cpio
is somehow broken. Can anyone provide another working mini-set of root ?
Thanks,
--
Tony C. Wu
System administrator Email: tonywu@life.nthu.edu.tw
Dept. of Life Sciences Voice: +886-3-574-2772
NTHU, Hsin-Chu, Taiwan Fax: +886-3-571-5934
On Thu, 12 Mar 1998, Alan Cox wrote:
> > 2.1.72_NOSL: put me in repair fs mode, but i can't change anything.
> > It said it couldn't read superblock on /dev/sdb
>
> Ok. The disk image expects to be /dev/sdb
> do
>
>
> mount -n -o remount,rw /dev/sdb1 /
>
> vi /etc/fstab
>
> change /dev/sdb to /dev/sdb1
>
> exit
>
>
> Best of luck
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Getting Started ..... NOT
1998-03-13 5:22 ` Tony C. Wu
@ 1998-03-24 18:19 ` Francis M. J. Hsieh
0 siblings, 0 replies; 8+ messages in thread
From: Francis M. J. Hsieh @ 1998-03-24 18:19 UTC (permalink / raw)
To: linux
At 01:22 PM 1998/3/13 +0800, you wrote:
>Ok. done that. I can successfully remount the / rw, but still, wont go any
>further. I tested fsck manually, no matter what device I specified, it
>always printed the same error and exited immediately. If I comment fsck
>part, and boot directly, still wont go. So I think the root-be-0.03-cpio
>is somehow broken. Can anyone provide another working mini-set of root ?
Well, is there any new root-be-*-cpio currently?
--
Francis Meng Juei Hsieh, Life Science Department, NTHU, Taiwan.
Welcome to Life Science BBS bbs.life.nthu.edu.tw (140.114.98.61)
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~1998-03-24 18:25 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
1998-03-12 19:35 Getting Started ..... NOT Tony C. Wu
1998-03-12 20:44 ` Eric Kimminau
1998-03-12 21:20 ` Alex deVries
1998-03-12 21:48 ` Eric Kimminau
1998-03-12 21:16 ` Alan Cox
1998-03-12 21:16 ` Alan Cox
1998-03-13 5:22 ` Tony C. Wu
1998-03-24 18:19 ` Francis M. J. Hsieh
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox