* [PATCH 1/3] Alchemy: merge small board files into single files
[not found] ` <cover.1226083170.git.mano@roarinelk.homelinux.net>
@ 2008-11-07 18:41 ` Manuel Lauss
2008-11-07 18:41 ` [PATCH 2/3] Alchemy: Move evalboard code to common directory Manuel Lauss
2008-11-07 18:41 ` [PATCH 3/3] Alchemy: common reset code is evalboard code Manuel Lauss
2 siblings, 0 replies; 7+ messages in thread
From: Manuel Lauss @ 2008-11-07 18:41 UTC (permalink / raw)
To: Linux-MIPS; +Cc: Manuel Lauss
Most files of the Alchemy boards are very small. Merge them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
---
arch/mips/alchemy/db1x00/Makefile | 2 +-
arch/mips/alchemy/db1x00/board_setup.c | 92 +++++++++++++++++-
arch/mips/alchemy/db1x00/init.c | 62 ------------
arch/mips/alchemy/db1x00/irqmap.c | 86 ----------------
arch/mips/alchemy/mtx-1/Makefile | 2 +-
arch/mips/alchemy/mtx-1/board_setup.c | 52 ++++++++++-
arch/mips/alchemy/mtx-1/init.c | 60 -----------
arch/mips/alchemy/mtx-1/irqmap.c | 52 ----------
arch/mips/alchemy/pb1000/Makefile | 2 +-
arch/mips/alchemy/pb1000/board_setup.c | 36 +++++++-
arch/mips/alchemy/pb1000/init.c | 57 -----------
arch/mips/alchemy/pb1000/irqmap.c | 38 -------
arch/mips/alchemy/pb1100/Makefile | 2 +-
arch/mips/alchemy/pb1100/board_setup.c | 42 ++++++++-
arch/mips/alchemy/pb1100/init.c | 60 -----------
arch/mips/alchemy/pb1100/irqmap.c | 40 --------
arch/mips/alchemy/pb1200/Makefile | 2 +-
arch/mips/alchemy/pb1200/board_setup.c | 162 ++++++++++++++++++++++++++++++-
arch/mips/alchemy/pb1200/init.c | 58 -----------
arch/mips/alchemy/pb1200/irqmap.c | 160 ------------------------------
arch/mips/alchemy/pb1500/Makefile | 2 +-
arch/mips/alchemy/pb1500/board_setup.c | 46 +++++++++-
arch/mips/alchemy/pb1500/init.c | 58 -----------
arch/mips/alchemy/pb1500/irqmap.c | 46 ---------
arch/mips/alchemy/pb1550/Makefile | 2 +-
arch/mips/alchemy/pb1550/board_setup.c | 41 ++++++++-
arch/mips/alchemy/pb1550/init.c | 58 -----------
arch/mips/alchemy/pb1550/irqmap.c | 43 --------
arch/mips/alchemy/xxs1500/Makefile | 2 +-
arch/mips/alchemy/xxs1500/board_setup.c | 50 +++++++++-
arch/mips/alchemy/xxs1500/init.c | 58 -----------
arch/mips/alchemy/xxs1500/irqmap.c | 49 ---------
32 files changed, 513 insertions(+), 1009 deletions(-)
delete mode 100644 arch/mips/alchemy/db1x00/init.c
delete mode 100644 arch/mips/alchemy/db1x00/irqmap.c
delete mode 100644 arch/mips/alchemy/mtx-1/init.c
delete mode 100644 arch/mips/alchemy/mtx-1/irqmap.c
delete mode 100644 arch/mips/alchemy/pb1000/init.c
delete mode 100644 arch/mips/alchemy/pb1000/irqmap.c
delete mode 100644 arch/mips/alchemy/pb1100/init.c
delete mode 100644 arch/mips/alchemy/pb1100/irqmap.c
delete mode 100644 arch/mips/alchemy/pb1200/init.c
delete mode 100644 arch/mips/alchemy/pb1200/irqmap.c
delete mode 100644 arch/mips/alchemy/pb1500/init.c
delete mode 100644 arch/mips/alchemy/pb1500/irqmap.c
delete mode 100644 arch/mips/alchemy/pb1550/init.c
delete mode 100644 arch/mips/alchemy/pb1550/irqmap.c
delete mode 100644 arch/mips/alchemy/xxs1500/init.c
delete mode 100644 arch/mips/alchemy/xxs1500/irqmap.c
diff --git a/arch/mips/alchemy/db1x00/Makefile b/arch/mips/alchemy/db1x00/Makefile
index 274db3b..9924aa0 100644
--- a/arch/mips/alchemy/db1x00/Makefile
+++ b/arch/mips/alchemy/db1x00/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/db1x00/board_setup.c b/arch/mips/alchemy/db1x00/board_setup.c
index 9e5ccbb..507ded2 100644
--- a/arch/mips/alchemy/db1x00/board_setup.c
+++ b/arch/mips/alchemy/db1x00/board_setup.c
@@ -1,7 +1,10 @@
/*
*
* BRIEF MODULE DESCRIPTION
- * Alchemy Db1x00 board setup.
+ * Alchemy Db1x00 board support.
+ *
+ * Copyright 2003 Embedded Edge, LLC
+ * dan@embeddededge.com
*
* Copyright 2000, 2008 MontaVista Software Inc.
* Author: MontaVista Software, Inc. <source@mvista.com>
@@ -28,12 +31,99 @@
*/
#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <prom.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-db1x00/db1x00.h>
+#ifdef CONFIG_MIPS_DB1500
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+#endif
+
+#ifdef CONFIG_MIPS_BOSPORUS
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI */
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+#endif
+
+#ifdef CONFIG_MIPS_MIRAGE
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
+ [12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
+ [13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
+};
+#endif
+
+#ifdef CONFIG_MIPS_DB1550
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
+ [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+#endif
+
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+
+#ifndef CONFIG_MIPS_MIRAGE
+#ifdef CONFIG_MIPS_DB1550
+ { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
+ { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
+#else
+ { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 Fully_Interted# */
+ { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 STSCHG# */
+ { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
+
+ { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 Fully_Interted# */
+ { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 STSCHG# */
+ { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
+#endif
+#else
+ { AU1000_GPIO_7, INTC_INT_RISE_EDGE, 0 }, /* touchscreen pen down */
+#endif
+
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+const char *get_system_type(void)
+{
+#ifdef CONFIG_MIPS_BOSPORUS
+ return "Alchemy Bosporus Gateway Reference";
+#else
+ return "Alchemy Db1x00";
+#endif
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
void board_reset(void)
{
/* Hit BCSR.SW_RESET[RESET] */
diff --git a/arch/mips/alchemy/db1x00/init.c b/arch/mips/alchemy/db1x00/init.c
deleted file mode 100644
index 8474135..0000000
--- a/arch/mips/alchemy/db1x00/init.c
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * PB1000 board setup
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
-#ifdef CONFIG_MIPS_BOSPORUS
- return "Alchemy Bosporus Gateway Reference";
-#else
- return "Alchemy Db1x00";
-#endif
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/db1x00/irqmap.c b/arch/mips/alchemy/db1x00/irqmap.c
deleted file mode 100644
index 94c090e..0000000
--- a/arch/mips/alchemy/db1x00/irqmap.c
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_DB1500
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI */
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_MIRAGE
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
- [12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
- [13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
-};
-#endif
-
-#ifdef CONFIG_MIPS_DB1550
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-#endif
-
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-
-#ifndef CONFIG_MIPS_MIRAGE
-#ifdef CONFIG_MIPS_DB1550
- { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
- { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
-#else
- { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 Fully_Interted# */
- { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 STSCHG# */
- { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
-
- { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 Fully_Interted# */
- { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 STSCHG# */
- { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
-#endif
-#else
- { AU1000_GPIO_7, INTC_INT_RISE_EDGE, 0 }, /* touchscreen pen down */
-#endif
-
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/mtx-1/Makefile b/arch/mips/alchemy/mtx-1/Makefile
index 7c67b3d..f011b2d 100644
--- a/arch/mips/alchemy/mtx-1/Makefile
+++ b/arch/mips/alchemy/mtx-1/Makefile
@@ -6,7 +6,7 @@
# Makefile for 4G Systems MTX-1 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
obj-y := platform.o
EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
index 3f80791..2e26465 100644
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ b/arch/mips/alchemy/mtx-1/board_setup.c
@@ -29,12 +29,61 @@
*/
#include <linux/init.h>
-
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
int mtx1_pci_idsel(unsigned int devsel, int assert);
+char irq_tab_alchemy[][5] __initdata = {
+ [0] = { -1, INTA, INTA, INTX, INTX }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+ [1] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+ [2] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+ [3] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+ [4] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+ [5] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+ [6] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+ [7] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
+ { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "MTX-1";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
void board_reset(void)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
@@ -95,4 +144,3 @@ mtx1_pci_idsel(unsigned int devsel, int assert)
au_sync_udelay(1);
return 1;
}
-
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
deleted file mode 100644
index 3bae13c..0000000
--- a/arch/mips/alchemy/mtx-1/init.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * 4G Systems MTX-1 board setup
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- * Bruno Randolf <bruno.randolf@4g-systems.biz>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "MTX-1";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/mtx-1/irqmap.c b/arch/mips/alchemy/mtx-1/irqmap.c
deleted file mode 100644
index f2bf029..0000000
--- a/arch/mips/alchemy/mtx-1/irqmap.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [0] = { -1, INTA, INTA, INTX, INTX }, /* IDSEL 00 - AdapterA-Slot0 (top) */
- [1] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
- [2] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 02 - AdapterB-Slot0 (top) */
- [3] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
- [4] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 04 - AdapterC-Slot0 (top) */
- [5] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
- [6] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 06 - AdapterD-Slot0 (top) */
- [7] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
- { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/pb1000/Makefile b/arch/mips/alchemy/pb1000/Makefile
index 99bbec0..4377ab3 100644
--- a/arch/mips/alchemy/pb1000/Makefile
+++ b/arch/mips/alchemy/pb1000/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1000 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1000/board_setup.c b/arch/mips/alchemy/pb1000/board_setup.c
index 25df167..bd0b6f4 100644
--- a/arch/mips/alchemy/pb1000/board_setup.c
+++ b/arch/mips/alchemy/pb1000/board_setup.c
@@ -23,11 +23,43 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/init.h>
#include <linux/delay.h>
-
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1000.h>
+#include <prom.h>
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1000";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = (int)fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
void board_reset(void)
{
diff --git a/arch/mips/alchemy/pb1000/init.c b/arch/mips/alchemy/pb1000/init.c
deleted file mode 100644
index 8a9c7d5..0000000
--- a/arch/mips/alchemy/pb1000/init.c
+++ /dev/null
@@ -1,57 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Pb1000 board setup
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1000";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/pb1000/irqmap.c b/arch/mips/alchemy/pb1000/irqmap.c
deleted file mode 100644
index b3d56b0..0000000
--- a/arch/mips/alchemy/pb1000/irqmap.c
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/pb1100/Makefile b/arch/mips/alchemy/pb1100/Makefile
index 793e97c..627a75c 100644
--- a/arch/mips/alchemy/pb1100/Makefile
+++ b/arch/mips/alchemy/pb1100/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1100 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1100/board_setup.c b/arch/mips/alchemy/pb1100/board_setup.c
index c0bfd59..87da4a5 100644
--- a/arch/mips/alchemy/pb1100/board_setup.c
+++ b/arch/mips/alchemy/pb1100/board_setup.c
@@ -23,11 +23,49 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/init.h>
#include <linux/delay.h>
-
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1100.h>
+#include <prom.h>
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
+ { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
+ { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
+ { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1100";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg3;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
void board_reset(void)
{
diff --git a/arch/mips/alchemy/pb1100/init.c b/arch/mips/alchemy/pb1100/init.c
deleted file mode 100644
index 7c67923..0000000
--- a/arch/mips/alchemy/pb1100/init.c
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Pb1100 board setup
- *
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1100";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg3;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
-
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/pb1100/irqmap.c b/arch/mips/alchemy/pb1100/irqmap.c
deleted file mode 100644
index 9b7dd8b..0000000
--- a/arch/mips/alchemy/pb1100/irqmap.c
+++ /dev/null
@@ -1,40 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xx0 IRQ map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
- { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
- { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
- { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/pb1200/Makefile b/arch/mips/alchemy/pb1200/Makefile
index d678adf..e9b9d27 100644
--- a/arch/mips/alchemy/pb1200/Makefile
+++ b/arch/mips/alchemy/pb1200/Makefile
@@ -2,7 +2,7 @@
# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
obj-y += platform.o
EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/pb1200/board_setup.c b/arch/mips/alchemy/pb1200/board_setup.c
index 6cb2115..a336a7a 100644
--- a/arch/mips/alchemy/pb1200/board_setup.c
+++ b/arch/mips/alchemy/pb1200/board_setup.c
@@ -25,14 +25,168 @@
*/
#include <linux/init.h>
-#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_INT_BEGIN DB1200_INT_BEGIN
+#define PB1200_INT_END DB1200_INT_END
+#endif
#include <prom.h>
-#include <au1xxx.h>
-extern void _board_init_irq(void);
extern void (*board_init_irq)(void);
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ /* This is external interrupt cascade */
+ { AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+/*
+ * Support for External interrupts on the Pb1200 Development platform.
+ */
+static volatile int pb1200_cascade_en;
+
+irqreturn_t pb1200_cascade_handler(int irq, void *dev_id)
+{
+ unsigned short bisr = bcsr->int_status;
+ int extirq_nr = 0;
+
+ /* Clear all the edge interrupts. This has no effect on level. */
+ bcsr->int_status = bisr;
+ for ( ; bisr; bisr &= bisr - 1) {
+ extirq_nr = PB1200_INT_BEGIN + __ffs(bisr);
+ /* Ack and dispatch IRQ */
+ do_IRQ(extirq_nr);
+ }
+
+ return IRQ_RETVAL(1);
+}
+
+inline void pb1200_enable_irq(unsigned int irq_nr)
+{
+ bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
+ bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
+}
+
+inline void pb1200_disable_irq(unsigned int irq_nr)
+{
+ bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
+ bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
+}
+
+static unsigned int pb1200_setup_cascade(void)
+{
+ return request_irq(AU1000_GPIO_7, &pb1200_cascade_handler,
+ 0, "Pb1200 Cascade", &pb1200_cascade_handler);
+}
+
+static unsigned int pb1200_startup_irq(unsigned int irq)
+{
+ if (++pb1200_cascade_en == 1) {
+ int res;
+
+ res = pb1200_setup_cascade();
+ if (res)
+ return res;
+ }
+
+ pb1200_enable_irq(irq);
+
+ return 0;
+}
+
+static void pb1200_shutdown_irq(unsigned int irq)
+{
+ pb1200_disable_irq(irq);
+ if (--pb1200_cascade_en == 0)
+ free_irq(AU1000_GPIO_7, &pb1200_cascade_handler);
+}
+
+static struct irq_chip external_irq_type = {
+#ifdef CONFIG_MIPS_PB1200
+ .name = "Pb1200 Ext",
+#endif
+#ifdef CONFIG_MIPS_DB1200
+ .name = "Db1200 Ext",
+#endif
+ .startup = pb1200_startup_irq,
+ .shutdown = pb1200_shutdown_irq,
+ .ack = pb1200_disable_irq,
+ .mask = pb1200_disable_irq,
+ .mask_ack = pb1200_disable_irq,
+ .unmask = pb1200_enable_irq,
+};
+
+static void pb1200_init_irq(void)
+{
+ unsigned int irq;
+
+#ifdef CONFIG_MIPS_PB1200
+ /* We have a problem with CPLD rev 3. */
+ if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+#endif
+
+ for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++) {
+ set_irq_chip_and_handler(irq, &external_irq_type,
+ handle_level_irq);
+ pb1200_disable_irq(irq);
+ }
+
+ /*
+ * GPIO_7 can not be hooked here, so it is hooked upon first
+ * request of any source attached to the cascade.
+ */
+}
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1200";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = (int)fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x08000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
+
void board_reset(void)
{
bcsr->resets = 0;
@@ -126,7 +280,7 @@ void __init board_setup(void)
#endif
/* Setup Pb1200 External Interrupt Controller */
- board_init_irq = _board_init_irq;
+ board_init_irq = pb1200_init_irq;
}
int board_au1200fb_panel(void)
diff --git a/arch/mips/alchemy/pb1200/init.c b/arch/mips/alchemy/pb1200/init.c
deleted file mode 100644
index e9b2a0f..0000000
--- a/arch/mips/alchemy/pb1200/init.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * PB1200 board setup
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1200";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x08000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/pb1200/irqmap.c b/arch/mips/alchemy/pb1200/irqmap.c
deleted file mode 100644
index 2a505ad..0000000
--- a/arch/mips/alchemy/pb1200/irqmap.c
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- /* This is external interrupt cascade */
- { AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-/*
- * Support for External interrupts on the Pb1200 Development platform.
- */
-static volatile int pb1200_cascade_en;
-
-irqreturn_t pb1200_cascade_handler(int irq, void *dev_id)
-{
- unsigned short bisr = bcsr->int_status;
- int extirq_nr = 0;
-
- /* Clear all the edge interrupts. This has no effect on level. */
- bcsr->int_status = bisr;
- for ( ; bisr; bisr &= bisr - 1) {
- extirq_nr = PB1200_INT_BEGIN + __ffs(bisr);
- /* Ack and dispatch IRQ */
- do_IRQ(extirq_nr);
- }
-
- return IRQ_RETVAL(1);
-}
-
-inline void pb1200_enable_irq(unsigned int irq_nr)
-{
- bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
-}
-
-inline void pb1200_disable_irq(unsigned int irq_nr)
-{
- bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
-}
-
-static unsigned int pb1200_setup_cascade(void)
-{
- return request_irq(AU1000_GPIO_7, &pb1200_cascade_handler,
- 0, "Pb1200 Cascade", &pb1200_cascade_handler);
-}
-
-static unsigned int pb1200_startup_irq(unsigned int irq)
-{
- if (++pb1200_cascade_en == 1) {
- int res;
-
- res = pb1200_setup_cascade();
- if (res)
- return res;
- }
-
- pb1200_enable_irq(irq);
-
- return 0;
-}
-
-static void pb1200_shutdown_irq(unsigned int irq)
-{
- pb1200_disable_irq(irq);
- if (--pb1200_cascade_en == 0)
- free_irq(AU1000_GPIO_7, &pb1200_cascade_handler);
-}
-
-static struct irq_chip external_irq_type = {
-#ifdef CONFIG_MIPS_PB1200
- .name = "Pb1200 Ext",
-#endif
-#ifdef CONFIG_MIPS_DB1200
- .name = "Db1200 Ext",
-#endif
- .startup = pb1200_startup_irq,
- .shutdown = pb1200_shutdown_irq,
- .ack = pb1200_disable_irq,
- .mask = pb1200_disable_irq,
- .mask_ack = pb1200_disable_irq,
- .unmask = pb1200_enable_irq,
-};
-
-void _board_init_irq(void)
-{
- unsigned int irq;
-
-#ifdef CONFIG_MIPS_PB1200
- /* We have a problem with CPLD rev 3. */
- if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-#endif
-
- for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++) {
- set_irq_chip_and_handler(irq, &external_irq_type,
- handle_level_irq);
- pb1200_disable_irq(irq);
- }
-
- /*
- * GPIO_7 can not be hooked here, so it is hooked upon first
- * request of any source attached to the cascade.
- */
-}
diff --git a/arch/mips/alchemy/pb1500/Makefile b/arch/mips/alchemy/pb1500/Makefile
index 602f38d..4664d61 100644
--- a/arch/mips/alchemy/pb1500/Makefile
+++ b/arch/mips/alchemy/pb1500/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1500 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1500/board_setup.c b/arch/mips/alchemy/pb1500/board_setup.c
index 035771c..1be1afc 100644
--- a/arch/mips/alchemy/pb1500/board_setup.c
+++ b/arch/mips/alchemy/pb1500/board_setup.c
@@ -23,11 +23,53 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/init.h>
#include <linux/delay.h>
-
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1500.h>
+#include <prom.h>
+
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
+ { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1500";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = (int)fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
void board_reset(void)
{
diff --git a/arch/mips/alchemy/pb1500/init.c b/arch/mips/alchemy/pb1500/init.c
deleted file mode 100644
index 3b6e395..0000000
--- a/arch/mips/alchemy/pb1500/init.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Pb1500 board setup
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1500";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/pb1500/irqmap.c b/arch/mips/alchemy/pb1500/irqmap.c
deleted file mode 100644
index 39c4682..0000000
--- a/arch/mips/alchemy/pb1500/irqmap.c
+++ /dev/null
@@ -1,46 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
- { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/pb1550/Makefile b/arch/mips/alchemy/pb1550/Makefile
index 7d8beca..7e6453d 100644
--- a/arch/mips/alchemy/pb1550/Makefile
+++ b/arch/mips/alchemy/pb1550/Makefile
@@ -5,4 +5,4 @@
# Makefile for the Alchemy Semiconductor Pb1550 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1550/board_setup.c b/arch/mips/alchemy/pb1550/board_setup.c
index 0ed76b6..e844484 100644
--- a/arch/mips/alchemy/pb1550/board_setup.c
+++ b/arch/mips/alchemy/pb1550/board_setup.c
@@ -28,9 +28,48 @@
*/
#include <linux/init.h>
-
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1550.h>
+#include <prom.h>
+
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1550";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = (int)fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x08000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
void board_reset(void)
{
diff --git a/arch/mips/alchemy/pb1550/init.c b/arch/mips/alchemy/pb1550/init.c
deleted file mode 100644
index e1055a1..0000000
--- a/arch/mips/alchemy/pb1550/init.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Pb1550 board setup
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1550";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x08000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/pb1550/irqmap.c b/arch/mips/alchemy/pb1550/irqmap.c
deleted file mode 100644
index a02a4d1..0000000
--- a/arch/mips/alchemy/pb1550/irqmap.c
+++ /dev/null
@@ -1,43 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xx0 IRQ map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
diff --git a/arch/mips/alchemy/xxs1500/Makefile b/arch/mips/alchemy/xxs1500/Makefile
index db3c526..9ec3b54 100644
--- a/arch/mips/alchemy/xxs1500/Makefile
+++ b/arch/mips/alchemy/xxs1500/Makefile
@@ -5,4 +5,4 @@
# Makefile for MyCable XXS1500 board.
#
-lib-y := init.o board_setup.o irqmap.o
+lib-y := board_setup.o
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index 4c587ac..813668f 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -23,10 +23,56 @@
* 675 Mass Ave, Cambridge, MA 02139, USA.
*/
-#include <linux/init.h>
#include <linux/delay.h>
-
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
+ { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_207, INTC_INT_LOW_LEVEL, 0 },
+
+ { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* CF interrupt */
+ { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "XXS1500";
+}
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = 0x04000000;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
void board_reset(void)
{
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
deleted file mode 100644
index 7516434..0000000
--- a/arch/mips/alchemy/xxs1500/init.c
+++ /dev/null
@@ -1,58 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * XXS1500 board setup
- *
- * Copyright 2003, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-
-#include <asm/bootinfo.h>
-
-#include <prom.h>
-
-const char *get_system_type(void)
-{
- return "XXS1500";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
diff --git a/arch/mips/alchemy/xxs1500/irqmap.c b/arch/mips/alchemy/xxs1500/irqmap.c
deleted file mode 100644
index edf06ed..0000000
--- a/arch/mips/alchemy/xxs1500/irqmap.c
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- * Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
- { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_207, INTC_INT_LOW_LEVEL, 0 },
-
- { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* CF interrupt */
- { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
--
1.6.0.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 2/3] Alchemy: Move evalboard code to common directory
[not found] ` <cover.1226083170.git.mano@roarinelk.homelinux.net>
2008-11-07 18:41 ` [PATCH 1/3] Alchemy: merge small board files into single files Manuel Lauss
@ 2008-11-07 18:41 ` Manuel Lauss
2008-11-07 18:41 ` [PATCH 3/3] Alchemy: common reset code is evalboard code Manuel Lauss
2 siblings, 0 replies; 7+ messages in thread
From: Manuel Lauss @ 2008-11-07 18:41 UTC (permalink / raw)
To: Linux-MIPS; +Cc: Manuel Lauss
Move all code of the Pb/Db boards to a single subdirectory and extract
some common code.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
---
arch/mips/Makefile | 24 +-
arch/mips/alchemy/db1x00/Makefile | 8 -
arch/mips/alchemy/db1x00/board_setup.c | 198 ---------------
arch/mips/alchemy/evalboards/Makefile | 17 ++
arch/mips/alchemy/evalboards/common.c | 62 +++++
arch/mips/alchemy/evalboards/db1x00.c | 178 +++++++++++++
arch/mips/alchemy/evalboards/pb1000.c | 178 +++++++++++++
arch/mips/alchemy/evalboards/pb1100.c | 124 +++++++++
arch/mips/alchemy/evalboards/pb1200.c | 293 ++++++++++++++++++++++
arch/mips/alchemy/evalboards/pb1200_platform.c | 166 +++++++++++++
arch/mips/alchemy/evalboards/pb1500.c | 140 +++++++++++
arch/mips/alchemy/evalboards/pb1550.c | 76 ++++++
arch/mips/alchemy/pb1000/Makefile | 8 -
arch/mips/alchemy/pb1000/board_setup.c | 197 ---------------
arch/mips/alchemy/pb1100/Makefile | 8 -
arch/mips/alchemy/pb1100/board_setup.c | 147 -----------
arch/mips/alchemy/pb1200/Makefile | 8 -
arch/mips/alchemy/pb1200/board_setup.c | 316 ------------------------
arch/mips/alchemy/pb1200/platform.c | 166 -------------
arch/mips/alchemy/pb1500/Makefile | 8 -
arch/mips/alchemy/pb1500/board_setup.c | 161 ------------
arch/mips/alchemy/pb1550/Makefile | 8 -
arch/mips/alchemy/pb1550/board_setup.c | 97 --------
23 files changed, 1246 insertions(+), 1342 deletions(-)
delete mode 100644 arch/mips/alchemy/db1x00/Makefile
delete mode 100644 arch/mips/alchemy/db1x00/board_setup.c
create mode 100644 arch/mips/alchemy/evalboards/Makefile
create mode 100644 arch/mips/alchemy/evalboards/common.c
create mode 100644 arch/mips/alchemy/evalboards/db1x00.c
create mode 100644 arch/mips/alchemy/evalboards/pb1000.c
create mode 100644 arch/mips/alchemy/evalboards/pb1100.c
create mode 100644 arch/mips/alchemy/evalboards/pb1200.c
create mode 100644 arch/mips/alchemy/evalboards/pb1200_platform.c
create mode 100644 arch/mips/alchemy/evalboards/pb1500.c
create mode 100644 arch/mips/alchemy/evalboards/pb1550.c
delete mode 100644 arch/mips/alchemy/pb1000/Makefile
delete mode 100644 arch/mips/alchemy/pb1000/board_setup.c
delete mode 100644 arch/mips/alchemy/pb1100/Makefile
delete mode 100644 arch/mips/alchemy/pb1100/board_setup.c
delete mode 100644 arch/mips/alchemy/pb1200/Makefile
delete mode 100644 arch/mips/alchemy/pb1200/board_setup.c
delete mode 100644 arch/mips/alchemy/pb1200/platform.c
delete mode 100644 arch/mips/alchemy/pb1500/Makefile
delete mode 100644 arch/mips/alchemy/pb1500/board_setup.c
delete mode 100644 arch/mips/alchemy/pb1550/Makefile
delete mode 100644 arch/mips/alchemy/pb1550/board_setup.c
diff --git a/arch/mips/Makefile b/arch/mips/Makefile
index 28c55f6..b31764e 100644
--- a/arch/mips/Makefile
+++ b/arch/mips/Makefile
@@ -184,84 +184,84 @@ cflags-$(CONFIG_SOC_AU1X00) += -I$(srctree)/arch/mips/include/asm/mach-au1x00
#
# AMD Alchemy Pb1000 eval board
#
-libs-$(CONFIG_MIPS_PB1000) += arch/mips/alchemy/pb1000/
+core-$(CONFIG_MIPS_PB1000) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_PB1000) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1000) += 0xffffffff80100000
#
# AMD Alchemy Pb1100 eval board
#
-libs-$(CONFIG_MIPS_PB1100) += arch/mips/alchemy/pb1100/
+core-$(CONFIG_MIPS_PB1100) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_PB1100) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1100) += 0xffffffff80100000
#
# AMD Alchemy Pb1500 eval board
#
-libs-$(CONFIG_MIPS_PB1500) += arch/mips/alchemy/pb1500/
+core-$(CONFIG_MIPS_PB1500) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_PB1500) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1500) += 0xffffffff80100000
#
# AMD Alchemy Pb1550 eval board
#
-libs-$(CONFIG_MIPS_PB1550) += arch/mips/alchemy/pb1550/
+core-$(CONFIG_MIPS_PB1550) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_PB1550) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1550) += 0xffffffff80100000
#
# AMD Alchemy Pb1200 eval board
#
-libs-$(CONFIG_MIPS_PB1200) += arch/mips/alchemy/pb1200/
+core-$(CONFIG_MIPS_PB1200) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_PB1200) += -I$(srctree)/arch/mips/include/asm/mach-pb1x00
load-$(CONFIG_MIPS_PB1200) += 0xffffffff80100000
#
# AMD Alchemy Db1000 eval board
#
-libs-$(CONFIG_MIPS_DB1000) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_DB1000) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_DB1000) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1000) += 0xffffffff80100000
#
# AMD Alchemy Db1100 eval board
#
-libs-$(CONFIG_MIPS_DB1100) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_DB1100) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_DB1100) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1100) += 0xffffffff80100000
#
# AMD Alchemy Db1500 eval board
#
-libs-$(CONFIG_MIPS_DB1500) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_DB1500) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_DB1500) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1500) += 0xffffffff80100000
#
# AMD Alchemy Db1550 eval board
#
-libs-$(CONFIG_MIPS_DB1550) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_DB1550) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_DB1550) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1550) += 0xffffffff80100000
#
# AMD Alchemy Db1200 eval board
#
-libs-$(CONFIG_MIPS_DB1200) += arch/mips/alchemy/pb1200/
+core-$(CONFIG_MIPS_DB1200) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_DB1200) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_DB1200) += 0xffffffff80100000
#
# AMD Alchemy Bosporus eval board
#
-libs-$(CONFIG_MIPS_BOSPORUS) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_BOSPORUS) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_BOSPORUS) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_BOSPORUS) += 0xffffffff80100000
#
# AMD Alchemy Mirage eval board
#
-libs-$(CONFIG_MIPS_MIRAGE) += arch/mips/alchemy/db1x00/
+core-$(CONFIG_MIPS_MIRAGE) += arch/mips/alchemy/evalboards/
cflags-$(CONFIG_MIPS_MIRAGE) += -I$(srctree)/arch/mips/include/asm/mach-db1x00
load-$(CONFIG_MIPS_MIRAGE) += 0xffffffff80100000
diff --git a/arch/mips/alchemy/db1x00/Makefile b/arch/mips/alchemy/db1x00/Makefile
deleted file mode 100644
index 9924aa0..0000000
--- a/arch/mips/alchemy/db1x00/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
-#
-
-lib-y := board_setup.o
diff --git a/arch/mips/alchemy/db1x00/board_setup.c b/arch/mips/alchemy/db1x00/board_setup.c
deleted file mode 100644
index 507ded2..0000000
--- a/arch/mips/alchemy/db1x00/board_setup.c
+++ /dev/null
@@ -1,198 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Db1x00 board support.
- *
- * Copyright 2003 Embedded Edge, LLC
- * dan@embeddededge.com
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <prom.h>
-
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-db1x00/db1x00.h>
-
-#ifdef CONFIG_MIPS_DB1500
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI */
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_MIRAGE
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
- [12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
- [13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
-};
-#endif
-
-#ifdef CONFIG_MIPS_DB1550
-char irq_tab_alchemy[][5] __initdata = {
- [11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-#endif
-
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-
-#ifndef CONFIG_MIPS_MIRAGE
-#ifdef CONFIG_MIPS_DB1550
- { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
- { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
-#else
- { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 Fully_Interted# */
- { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 STSCHG# */
- { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
-
- { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 Fully_Interted# */
- { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 STSCHG# */
- { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
-#endif
-#else
- { AU1000_GPIO_7, INTC_INT_RISE_EDGE, 0 }, /* touchscreen pen down */
-#endif
-
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
-const char *get_system_type(void)
-{
-#ifdef CONFIG_MIPS_BOSPORUS
- return "Alchemy Bosporus Gateway Reference";
-#else
- return "Alchemy Db1x00";
-#endif
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
- /* Hit BCSR.SW_RESET[RESET] */
- bcsr->swreset = 0x0000;
-}
-
-void __init board_setup(void)
-{
- u32 pin_func = 0;
-
- /* Not valid for Au1550 */
-#if defined(CONFIG_IRDA) && \
- (defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1100))
- /* Set IRFIRSEL instead of GPIO15 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
- au_writel(pin_func, SYS_PINFUNC);
- /* Power off until the driver is in use */
- bcsr->resets &= ~BCSR_RESETS_IRDA_MODE_MASK;
- bcsr->resets |= BCSR_RESETS_IRDA_MODE_OFF;
- au_sync();
-#endif
- bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
-
-#ifdef CONFIG_MIPS_MIRAGE
- /* Enable GPIO[31:0] inputs */
- au_writel(0, SYS_PININPUTEN);
-
- /* GPIO[20] is output, tristate the other input primary GPIOs */
- au_writel(~(1 << 20), SYS_TRIOUTCLR);
-
- /* Set GPIO[210:208] instead of SSI_0 */
- pin_func = au_readl(SYS_PINFUNC) | SYS_PF_S0;
-
- /* Set GPIO[215:211] for LEDs */
- pin_func |= 5 << 2;
-
- /* Set GPIO[214:213] for more LEDs */
- pin_func |= 5 << 12;
-
- /* Set GPIO[207:200] instead of PCMCIA/LCD */
- pin_func |= SYS_PF_LCD | SYS_PF_PC;
- au_writel(pin_func, SYS_PINFUNC);
-
- /*
- * Enable speaker amplifier. This should
- * be part of the audio driver.
- */
- au_writel(au_readl(GPIO2_DIR) | 0x200, GPIO2_DIR);
- au_writel(0x02000200, GPIO2_OUTPUT);
-#endif
-
- au_sync();
-
-#ifdef CONFIG_MIPS_DB1000
- printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
- printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
- printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
-#endif
-#ifdef CONFIG_MIPS_BOSPORUS
- printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
-#endif
-#ifdef CONFIG_MIPS_MIRAGE
- printk(KERN_INFO "AMD Alchemy Mirage Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1550
- printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
-#endif
-}
diff --git a/arch/mips/alchemy/evalboards/Makefile b/arch/mips/alchemy/evalboards/Makefile
new file mode 100644
index 0000000..56a67c6
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/Makefile
@@ -0,0 +1,17 @@
+#
+# Alchemy demoboards (Db1xx0/Pb1xx0/Bosporus/Mirage series).
+#
+
+obj-y += common.o
+obj-$(CONFIG_MIPS_PB1000) += pb1000.o
+obj-$(CONFIG_MIPS_PB1100) += pb1100.o
+obj-$(CONFIG_MIPS_PB1200) += pb1200.o pb1200_platform.o
+obj-$(CONFIG_MIPS_PB1500) += pb1500.o
+obj-$(CONFIG_MIPS_PB1550) += pb1550.o
+obj-$(CONFIG_MIPS_DB1000) += db1x00.o
+obj-$(CONFIG_MIPS_DB1100) += db1x00.o
+obj-$(CONFIG_MIPS_DB1200) += pb1200.o pb1200_platform.o
+obj-$(CONFIG_MIPS_DB1500) += db1x00.o
+obj-$(CONFIG_MIPS_DB1550) += db1x00.o
+obj-$(CONFIG_MIPS_BOSPORUS) += db1x00.o
+obj-$(CONFIG_MIPS_MIRAGE) += db1x00.o
diff --git a/arch/mips/alchemy/evalboards/common.c b/arch/mips/alchemy/evalboards/common.c
new file mode 100644
index 0000000..d112fcf
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/common.c
@@ -0,0 +1,62 @@
+/*
+ * Common code used by all Alchemy evalboards.
+ *
+ * Extracted from files which had this to say:
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <prom.h>
+
+#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_DB1000) || \
+ defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
+ defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
+ defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
+#define ALCHEMY_BOARD_DEFAULT_MEMSIZE 0x04000000
+
+#else
+#define ALCHEMY_BOARD_DEFAULT_MEMSIZE 0x08000000
+#endif
+
+void __init prom_init(void)
+{
+ unsigned char *memsize_str;
+ unsigned long memsize;
+
+ prom_argc = (int)fw_arg0;
+ prom_argv = (char **)fw_arg1;
+ prom_envp = (char **)fw_arg2;
+
+ prom_init_cmdline();
+ memsize_str = prom_getenv("memsize");
+ if (!memsize_str)
+ memsize = ALCHEMY_BOARD_DEFAULT_MEMSIZE;
+ else
+ strict_strtol(memsize_str, 0, &memsize);
+ add_memory_region(0, memsize, BOOT_MEM_RAM);
+}
diff --git a/arch/mips/alchemy/evalboards/db1x00.c b/arch/mips/alchemy/evalboards/db1x00.c
new file mode 100644
index 0000000..868ad3e
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/db1x00.c
@@ -0,0 +1,178 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ * Alchemy Db1x00 board support.
+ *
+ * Copyright 2003 Embedded Edge, LLC
+ * dan@embeddededge.com
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/db1x00.h>
+
+#ifdef CONFIG_MIPS_DB1500
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+#endif
+
+#ifdef CONFIG_MIPS_BOSPORUS
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI */
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+#endif
+
+#ifdef CONFIG_MIPS_MIRAGE
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
+ [12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
+ [13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
+};
+#endif
+
+#ifdef CONFIG_MIPS_DB1550
+char irq_tab_alchemy[][5] __initdata = {
+ [11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
+ [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+#endif
+
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+
+#ifndef CONFIG_MIPS_MIRAGE
+#ifdef CONFIG_MIPS_DB1550
+ { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
+ { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
+#else
+ { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 Fully_Interted# */
+ { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 STSCHG# */
+ { AU1000_GPIO_2, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 0 IRQ# */
+
+ { AU1000_GPIO_3, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 Fully_Interted# */
+ { AU1000_GPIO_4, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 STSCHG# */
+ { AU1000_GPIO_5, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card 1 IRQ# */
+#endif
+#else
+ { AU1000_GPIO_7, INTC_INT_RISE_EDGE, 0 }, /* touchscreen pen down */
+#endif
+
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+const char *get_system_type(void)
+{
+#ifdef CONFIG_MIPS_BOSPORUS
+ return "Alchemy Bosporus Gateway Reference";
+#else
+ return "Alchemy Db1x00";
+#endif
+}
+
+void board_reset(void)
+{
+ /* Hit BCSR.SW_RESET[RESET] */
+ bcsr->swreset = 0x0000;
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ pin_func = 0;
+
+ /* Not valid for Au1550 */
+#if defined(CONFIG_IRDA) && \
+ (defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1100))
+ /* Set IRFIRSEL instead of GPIO15 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
+ au_writel(pin_func, SYS_PINFUNC);
+ /* Power off until the driver is in use */
+ bcsr->resets &= ~BCSR_RESETS_IRDA_MODE_MASK;
+ bcsr->resets |= BCSR_RESETS_IRDA_MODE_OFF;
+ au_sync();
+#endif
+ bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
+
+#ifdef CONFIG_MIPS_MIRAGE
+ /* Enable GPIO[31:0] inputs */
+ au_writel(0, SYS_PININPUTEN);
+
+ /* GPIO[20] is output, tristate the other input primary GPIOs */
+ au_writel(~(1 << 20), SYS_TRIOUTCLR);
+
+ /* Set GPIO[210:208] instead of SSI_0 */
+ pin_func = au_readl(SYS_PINFUNC) | SYS_PF_S0;
+
+ /* Set GPIO[215:211] for LEDs */
+ pin_func |= 5 << 2;
+
+ /* Set GPIO[214:213] for more LEDs */
+ pin_func |= 5 << 12;
+
+ /* Set GPIO[207:200] instead of PCMCIA/LCD */
+ pin_func |= SYS_PF_LCD | SYS_PF_PC;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ /*
+ * Enable speaker amplifier. This should
+ * be part of the audio driver.
+ */
+ au_writel(au_readl(GPIO2_DIR) | 0x200, GPIO2_DIR);
+ au_writel(0x02000200, GPIO2_OUTPUT);
+#endif
+
+ au_sync();
+
+#ifdef CONFIG_MIPS_DB1000
+ printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+ printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1100
+ printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+#ifdef CONFIG_MIPS_BOSPORUS
+ printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
+#endif
+#ifdef CONFIG_MIPS_MIRAGE
+ printk(KERN_INFO "AMD Alchemy Mirage Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1550
+ printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
+#endif
+}
diff --git a/arch/mips/alchemy/evalboards/pb1000.c b/arch/mips/alchemy/evalboards/pb1000.c
new file mode 100644
index 0000000..e795eaf
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1000.c
@@ -0,0 +1,178 @@
+/*
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1000.h>
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1000";
+}
+
+void board_reset(void)
+{
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func, static_cfg0;
+ u32 sys_freqctrl, sys_clksrc;
+ u32 prid = read_c0_prid();
+
+ sys_freqctrl = sys_clksrc = 0;
+
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ au_writel(0, SYS_PINSTATERD);
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* Zero and disable USBH/USBD clocks */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+ switch (prid & 0x000000FF) {
+ case 0x00: /* DA */
+ case 0x01: /* HA */
+ case 0x02: /* HB */
+ /* CPU core freq to 48 MHz to slow it way down... */
+ au_writel(4, SYS_CPUPLL);
+
+ /*
+ * Setup 48 MHz FREQ2 from CPUPLL for USB Host
+ * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
+ */
+ sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* CPU core freq to 384 MHz */
+ au_writel(0x20, SYS_CPUPLL);
+
+ printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
+ break;
+
+ default: /* HC and newer */
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+ break;
+ }
+
+ /*
+ * Route 48 MHz FREQ2 into USB Host and/or Device
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
+
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
+
+ au_writel(pin_func, SYS_PINFUNC);
+ au_writel(0x2800, SYS_TRIOUTCLR);
+ au_writel(0x0030, SYS_OUTPUTCLR);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Make GPIO 15 an input (for interrupt line) */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
+ /* We don't need I2S, so make it available for GPIO[31:29] */
+ pin_func |= SYS_PF_I2S;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0x8000, SYS_TRIOUTCLR);
+
+ static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
+ au_writel(static_cfg0, MEM_STCFG0);
+
+ /* configure RCE2* for LCD */
+ au_writel(0x00000004, MEM_STCFG2);
+
+ /* MEM_STTIME2 */
+ au_writel(0x09000000, MEM_STTIME2);
+
+ /* Set 32-bit base address decoding for RCE2* */
+ au_writel(0x10003ff0, MEM_STADDR2);
+
+ /*
+ * PCI CPLD setup
+ * Expand CE0 to cover PCI
+ */
+ au_writel(0x11803e40, MEM_STADDR1);
+
+ /* Burst visibility on */
+ au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
+
+ au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
+ au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
+
+ /* Setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ /*
+ * Enable Au1000 BCLK switching - note: sed1356 must not use
+ * its BCLK (Au1000 LCLK) for any timings
+ */
+ switch (prid & 0x000000FF) {
+ case 0x00: /* DA */
+ case 0x01: /* HA */
+ case 0x02: /* HB */
+ break;
+ default: /* HC and newer */
+ /*
+ * Enable sys bus clock divider when IDLE state or no bus
+ * activity.
+ */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+ break;
+ }
+}
diff --git a/arch/mips/alchemy/evalboards/pb1100.c b/arch/mips/alchemy/evalboards/pb1100.c
new file mode 100644
index 0000000..dbd9605
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1100.c
@@ -0,0 +1,124 @@
+/*
+ * Copyright 2002, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1100.h>
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
+ { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
+ { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
+ { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1100";
+}
+
+void board_reset(void)
+{
+ /* Hit BCSR.RST_VDDI[SOFT_RESET] */
+ au_writel(0x00000000, PB1100_RST_VDDI);
+}
+
+void __init board_setup(void)
+{
+ volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ au_writel(0, SYS_PININPUTEN);
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+ {
+ u32 pin_func, sys_freqctrl, sys_clksrc;
+
+ /* Configure pins GPIO[14:9] as GPIO */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* Zero and disable USBH/USBD/IrDA clock */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+
+ /* FREQ2 = aux / 2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+ SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48 MHz FREQ2 into USBH/USBD/IrDA
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ /* Setup the static bus controller */
+ au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
+ au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+ au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+ /*
+ * Get USB Functionality pin state (device vs host drive pins).
+ */
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host. */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+ }
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled. */
+ if (!(readb(base + 0x28) & 0x20)) {
+ writeb(readb(base + 0x28) | 0x20, base + 0x28);
+ au_sync();
+ }
+ /* Put the clock in BCD mode. */
+ if (readb(base + 0x2C) & 0x4) { /* reg B */
+ writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
+ au_sync();
+ }
+}
diff --git a/arch/mips/alchemy/evalboards/pb1200.c b/arch/mips/alchemy/evalboards/pb1200.c
new file mode 100644
index 0000000..4a24874
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1200.c
@@ -0,0 +1,293 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ * Alchemy Pb1200/Db1200 board setup.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_INT_BEGIN DB1200_INT_BEGIN
+#define PB1200_INT_END DB1200_INT_END
+#endif
+
+#include <prom.h>
+
+extern void (*board_init_irq)(void);
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ /* This is external interrupt cascade */
+ { AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+/*
+ * Support for External interrupts on the Pb1200 Development platform.
+ */
+static volatile int pb1200_cascade_en;
+
+irqreturn_t pb1200_cascade_handler(int irq, void *dev_id)
+{
+ unsigned short bisr = bcsr->int_status;
+ int extirq_nr = 0;
+
+ /* Clear all the edge interrupts. This has no effect on level. */
+ bcsr->int_status = bisr;
+ for ( ; bisr; bisr &= bisr - 1) {
+ extirq_nr = PB1200_INT_BEGIN + __ffs(bisr);
+ /* Ack and dispatch IRQ */
+ do_IRQ(extirq_nr);
+ }
+
+ return IRQ_RETVAL(1);
+}
+
+inline void pb1200_enable_irq(unsigned int irq_nr)
+{
+ bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
+ bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
+}
+
+inline void pb1200_disable_irq(unsigned int irq_nr)
+{
+ bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
+ bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
+}
+
+static unsigned int pb1200_setup_cascade(void)
+{
+ return request_irq(AU1000_GPIO_7, &pb1200_cascade_handler,
+ 0, "Pb1200 Cascade", &pb1200_cascade_handler);
+}
+
+static unsigned int pb1200_startup_irq(unsigned int irq)
+{
+ if (++pb1200_cascade_en == 1) {
+ int res;
+
+ res = pb1200_setup_cascade();
+ if (res)
+ return res;
+ }
+
+ pb1200_enable_irq(irq);
+
+ return 0;
+}
+
+static void pb1200_shutdown_irq(unsigned int irq)
+{
+ pb1200_disable_irq(irq);
+ if (--pb1200_cascade_en == 0)
+ free_irq(AU1000_GPIO_7, &pb1200_cascade_handler);
+}
+
+static struct irq_chip external_irq_type = {
+#ifdef CONFIG_MIPS_PB1200
+ .name = "Pb1200 Ext",
+#endif
+#ifdef CONFIG_MIPS_DB1200
+ .name = "Db1200 Ext",
+#endif
+ .startup = pb1200_startup_irq,
+ .shutdown = pb1200_shutdown_irq,
+ .ack = pb1200_disable_irq,
+ .mask = pb1200_disable_irq,
+ .mask_ack = pb1200_disable_irq,
+ .unmask = pb1200_enable_irq,
+};
+
+static void pb1200_init_irq(void)
+{
+ unsigned int irq;
+
+#ifdef CONFIG_MIPS_PB1200
+ /* We have a problem with CPLD rev 3. */
+ if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+ printk(KERN_ERR "updated to latest revision. This software will\n");
+ printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ printk(KERN_ERR "WARNING!!!\n");
+ panic("Game over. Your score is 0.");
+ }
+#endif
+
+ for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++) {
+ set_irq_chip_and_handler(irq, &external_irq_type,
+ handle_level_irq);
+ pb1200_disable_irq(irq);
+ }
+
+ /*
+ * GPIO_7 can not be hooked here, so it is hooked upon first
+ * request of any source attached to the cascade.
+ */
+}
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1200";
+}
+
+void board_reset(void)
+{
+ bcsr->resets = 0;
+ bcsr->system = 0;
+}
+
+void __init board_setup(void)
+{
+#ifdef CONFIG_FB_AU1200
+ char *argptr;
+
+ argptr = prom_getcmdline();
+ strcat(argptr, " video=au1200fb:panel:bs");
+#endif
+
+#if 0
+ {
+ u32 pin_func;
+
+ /*
+ * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+ au_sync();
+ }
+#endif
+
+#if defined(CONFIG_I2C_AU1550)
+ {
+ u32 freq0, clksrc;
+ u32 pin_func;
+
+ /* Select SMBus in CPLD */
+ bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+ /* Set GPIOs correctly */
+ pin_func |= 2 << 17;
+ au_writel(pin_func, SYS_PINFUNC);
+ au_sync();
+
+ /* The I2C driver depends on 50 MHz clock */
+ freq0 = au_readl(SYS_FREQCTRL0);
+ au_sync();
+ freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
+ freq0 |= 3 << SYS_FC_FRDIV1_BIT;
+ /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+ freq0 |= SYS_FC_FE1;
+ au_writel(freq0, SYS_FREQCTRL0);
+ au_sync();
+
+ clksrc = au_readl(SYS_CLKSRC);
+ au_sync();
+ clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
+ /* Bit 22 is EXTCLK0 for PSC0 */
+ clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
+ au_writel(clksrc, SYS_CLKSRC);
+ au_sync();
+ }
+#endif
+
+ /*
+ * The Pb1200 development board uses external MUX for PSC0 to
+ * support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
+ */
+#ifdef CONFIG_I2C_AU1550
+ bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+#endif
+ au_sync();
+
+#ifdef CONFIG_MIPS_PB1200
+ printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1200
+ printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
+#endif
+
+ /* Setup Pb1200 External Interrupt Controller */
+ board_init_irq = pb1200_init_irq;
+}
+
+int board_au1200fb_panel(void)
+{
+ BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+ int p;
+
+ p = bcsr->switches;
+ p >>= 8;
+ p &= 0x0F;
+ return p;
+}
+
+int board_au1200fb_panel_init(void)
+{
+ /* Apply power */
+ BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+ bcsr->board |= BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL;
+ /* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
+ return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+ /* Remove power */
+ BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+ bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+ BCSR_BOARD_LCDBL);
+ /* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
+ return 0;
+}
diff --git a/arch/mips/alchemy/evalboards/pb1200_platform.c b/arch/mips/alchemy/evalboards/pb1200_platform.c
new file mode 100644
index 0000000..9530329
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1200_platform.c
@@ -0,0 +1,166 @@
+/*
+ * Pb1200/DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1xxx.h>
+#include <asm/mach-au1x00/au1100_mmc.h>
+
+static int mmc_activity;
+
+static void pb1200mmc0_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr->board |= BCSR_BOARD_SD0PWR;
+ else
+ bcsr->board &= ~BCSR_BOARD_SD0PWR;
+
+ au_sync_delay(1);
+}
+
+static int pb1200mmc0_card_readonly(void *mmc_host)
+{
+ return (bcsr->status & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int pb1200mmc0_card_inserted(void *mmc_host)
+{
+ return (bcsr->sig_status & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void pb1200_mmcled_set(struct led_classdev *led,
+ enum led_brightness brightness)
+{
+ if (brightness != LED_OFF) {
+ if (++mmc_activity == 1)
+ bcsr->disk_leds &= ~(1 << 8);
+ } else {
+ if (--mmc_activity == 0)
+ bcsr->disk_leds |= (1 << 8);
+ }
+}
+
+static struct led_classdev pb1200mmc_led = {
+ .brightness_set = pb1200_mmcled_set,
+};
+
+#ifndef CONFIG_MIPS_DB1200
+static void pb1200mmc1_set_power(void *mmc_host, int state)
+{
+ if (state)
+ bcsr->board |= BCSR_BOARD_SD1PWR;
+ else
+ bcsr->board &= ~BCSR_BOARD_SD1PWR;
+
+ au_sync_delay(1);
+}
+
+static int pb1200mmc1_card_readonly(void *mmc_host)
+{
+ return (bcsr->status & BCSR_STATUS_SD1WP) ? 1 : 0;
+}
+
+static int pb1200mmc1_card_inserted(void *mmc_host)
+{
+ return (bcsr->sig_status & BCSR_INT_SD1INSERT) ? 1 : 0;
+}
+#endif
+
+const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
+ [0] = {
+ .set_power = pb1200mmc0_set_power,
+ .card_inserted = pb1200mmc0_card_inserted,
+ .card_readonly = pb1200mmc0_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+#ifndef CONFIG_MIPS_DB1200
+ [1] = {
+ .set_power = pb1200mmc1_set_power,
+ .card_inserted = pb1200mmc1_card_inserted,
+ .card_readonly = pb1200mmc1_card_readonly,
+ .cd_setup = NULL, /* use poll-timer in driver */
+ .led = &pb1200mmc_led,
+ },
+#endif
+};
+
+static struct resource ide_resources[] = {
+ [0] = {
+ .start = IDE_PHYS_ADDR,
+ .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = IDE_INT,
+ .end = IDE_INT,
+ .flags = IORESOURCE_IRQ
+ }
+};
+
+static u64 ide_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device ide_device = {
+ .name = "au1200-ide",
+ .id = 0,
+ .dev = {
+ .dma_mask = &ide_dmamask,
+ .coherent_dma_mask = DMA_32BIT_MASK,
+ },
+ .num_resources = ARRAY_SIZE(ide_resources),
+ .resource = ide_resources
+};
+
+static struct resource smc91c111_resources[] = {
+ [0] = {
+ .name = "smc91x-regs",
+ .start = SMC91C111_PHYS_ADDR,
+ .end = SMC91C111_PHYS_ADDR + 0xf,
+ .flags = IORESOURCE_MEM
+ },
+ [1] = {
+ .start = SMC91C111_INT,
+ .end = SMC91C111_INT,
+ .flags = IORESOURCE_IRQ
+ },
+};
+
+static struct platform_device smc91c111_device = {
+ .name = "smc91x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smc91c111_resources),
+ .resource = smc91c111_resources
+};
+
+static struct platform_device *board_platform_devices[] __initdata = {
+ &ide_device,
+ &smc91c111_device
+};
+
+static int __init board_register_devices(void)
+{
+ return platform_add_devices(board_platform_devices,
+ ARRAY_SIZE(board_platform_devices));
+}
+
+arch_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/evalboards/pb1500.c b/arch/mips/alchemy/evalboards/pb1500.c
new file mode 100644
index 0000000..72c5222
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1500.c
@@ -0,0 +1,140 @@
+/*
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1500.h>
+
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
+};
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
+ { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
+ { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1500";
+}
+
+void board_reset(void)
+{
+ /* Hit BCSR.RST_VDDI[SOFT_RESET] */
+ au_writel(0x00000000, PB1500_RST_VDDI);
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+ u32 sys_freqctrl, sys_clksrc;
+
+ sys_clksrc = sys_freqctrl = pin_func = 0;
+ /* Set AUX clock to 12 MHz * 8 = 96 MHz */
+ au_writel(8, SYS_AUXPLL);
+ au_writel(0, SYS_PINSTATERD);
+ udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+
+ /* GPIO201 is input for PCMCIA card detect */
+ /* GPIO203 is input for PCMCIA interrupt request */
+ au_writel(au_readl(GPIO2_DIR) & ~((1 << 1) | (1 << 3)), GPIO2_DIR);
+
+ /* Zero and disable FREQ2 */
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /* zero and disable USBH/USBD clocks */
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ sys_freqctrl = au_readl(SYS_FREQCTRL0);
+ sys_freqctrl &= ~0xFFF00000;
+
+ sys_clksrc = au_readl(SYS_CLKSRC);
+ sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
+ SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
+
+ /* FREQ2 = aux/2 = 48 MHz */
+ sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
+ au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+ /*
+ * Route 48MHz FREQ2 into USB Host and/or Device
+ */
+ sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
+ au_writel(sys_clksrc, SYS_CLKSRC);
+
+ pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+ /* 2nd USB port is USB host */
+ pin_func |= SYS_PF_USB;
+ au_writel(pin_func, SYS_PINFUNC);
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+#ifdef CONFIG_PCI
+ /* Setup PCI bus controller */
+ au_writel(0, Au1500_PCI_CMEM);
+ au_writel(0x00003fff, Au1500_CFG_BASE);
+#if defined(__MIPSEB__)
+ au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
+#else
+ au_writel(0xf, Au1500_PCI_CFG);
+#endif
+ au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
+ au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
+ au_writel(0x02a00356, Au1500_PCI_STATCMD);
+ au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
+ au_writel(0x00000008, Au1500_PCI_MBAR);
+ au_sync();
+#endif
+
+ /* Enable sys bus clock divider when IDLE state or no bus activity. */
+ au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+ /* Enable the RTC if not already enabled */
+ if (!(au_readl(0xac000028) & 0x20)) {
+ printk(KERN_INFO "enabling clock ...\n");
+ au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
+ }
+ /* Put the clock in BCD mode */
+ if (au_readl(0xac00002c) & 0x4) { /* reg B */
+ au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
+ au_sync();
+ }
+}
diff --git a/arch/mips/alchemy/evalboards/pb1550.c b/arch/mips/alchemy/evalboards/pb1550.c
new file mode 100644
index 0000000..15bcf6b
--- /dev/null
+++ b/arch/mips/alchemy/evalboards/pb1550.c
@@ -0,0 +1,76 @@
+/*
+ *
+ * BRIEF MODULE DESCRIPTION
+ * Alchemy Pb1550 board setup.
+ *
+ * Copyright 2000, 2008 MontaVista Software Inc.
+ * Author: MontaVista Software, Inc. <source@mvista.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1550.h>
+
+char irq_tab_alchemy[][5] __initdata = {
+ [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+ [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+
+struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
+ { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
+ { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
+};
+
+int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
+
+
+const char *get_system_type(void)
+{
+ return "Alchemy Pb1550";
+}
+
+void board_reset(void)
+{
+ /* Hit BCSR.SYSTEM[RESET] */
+ au_writew(au_readw(0xAF00001C) & ~BCSR_SYSTEM_RESET, 0xAF00001C);
+}
+
+void __init board_setup(void)
+{
+ u32 pin_func;
+
+ /*
+ * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
+ * but it is board specific code, so put it here.
+ */
+ pin_func = au_readl(SYS_PINFUNC);
+ au_sync();
+ pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
+ au_writel(pin_func, SYS_PINFUNC);
+
+ au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
+ au_sync();
+
+ printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
+}
diff --git a/arch/mips/alchemy/pb1000/Makefile b/arch/mips/alchemy/pb1000/Makefile
deleted file mode 100644
index 4377ab3..0000000
--- a/arch/mips/alchemy/pb1000/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1000 board.
-#
-
-lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1000/board_setup.c b/arch/mips/alchemy/pb1000/board_setup.c
deleted file mode 100644
index bd0b6f4..0000000
--- a/arch/mips/alchemy/pb1000/board_setup.c
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1000.h>
-#include <prom.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1000";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
-}
-
-void __init board_setup(void)
-{
- u32 pin_func, static_cfg0;
- u32 sys_freqctrl, sys_clksrc;
- u32 prid = read_c0_prid();
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- au_writel(0, SYS_PINSTATERD);
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- /* CPU core freq to 48 MHz to slow it way down... */
- au_writel(4, SYS_CPUPLL);
-
- /*
- * Setup 48 MHz FREQ2 from CPUPLL for USB Host
- * FRDIV2 = 3 -> div by 8 of 384 MHz -> 48 MHz
- */
- sys_freqctrl |= (3 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* CPU core freq to 384 MHz */
- au_writel(0x20, SYS_CPUPLL);
-
- printk(KERN_INFO "Au1000: 48 MHz OHCI workaround enabled\n");
- break;
-
- default: /* HC and newer */
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
- break;
- }
-
- /*
- * Route 48 MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~(SYS_PF_UR3 | SYS_PF_USB);
-
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
-
- au_writel(pin_func, SYS_PINFUNC);
- au_writel(0x2800, SYS_TRIOUTCLR);
- au_writel(0x0030, SYS_OUTPUTCLR);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Make GPIO 15 an input (for interrupt line) */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_IRF;
- /* We don't need I2S, so make it available for GPIO[31:29] */
- pin_func |= SYS_PF_I2S;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0x8000, SYS_TRIOUTCLR);
-
- static_cfg0 = au_readl(MEM_STCFG0) & ~0xc00;
- au_writel(static_cfg0, MEM_STCFG0);
-
- /* configure RCE2* for LCD */
- au_writel(0x00000004, MEM_STCFG2);
-
- /* MEM_STTIME2 */
- au_writel(0x09000000, MEM_STTIME2);
-
- /* Set 32-bit base address decoding for RCE2* */
- au_writel(0x10003ff0, MEM_STADDR2);
-
- /*
- * PCI CPLD setup
- * Expand CE0 to cover PCI
- */
- au_writel(0x11803e40, MEM_STADDR1);
-
- /* Burst visibility on */
- au_writel(au_readl(MEM_STCFG0) | 0x1000, MEM_STCFG0);
-
- au_writel(0x83, MEM_STCFG1); /* ewait enabled, flash timing */
- au_writel(0x33030a10, MEM_STTIME1); /* slower timing for FPGA */
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Enable Au1000 BCLK switching - note: sed1356 must not use
- * its BCLK (Au1000 LCLK) for any timings
- */
- switch (prid & 0x000000FF) {
- case 0x00: /* DA */
- case 0x01: /* HA */
- case 0x02: /* HB */
- break;
- default: /* HC and newer */
- /*
- * Enable sys bus clock divider when IDLE state or no bus
- * activity.
- */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
- break;
- }
-}
diff --git a/arch/mips/alchemy/pb1100/Makefile b/arch/mips/alchemy/pb1100/Makefile
deleted file mode 100644
index 627a75c..0000000
--- a/arch/mips/alchemy/pb1100/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1100 board.
-#
-
-lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1100/board_setup.c b/arch/mips/alchemy/pb1100/board_setup.c
deleted file mode 100644
index 87da4a5..0000000
--- a/arch/mips/alchemy/pb1100/board_setup.c
+++ /dev/null
@@ -1,147 +0,0 @@
-/*
- * Copyright 2002, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1100.h>
-#include <prom.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
- { AU1000_GPIO_10, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card STSCHG# */
- { AU1000_GPIO_11, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card IRQ# */
- { AU1000_GPIO_13, INTC_INT_LOW_LEVEL, 0 }, /* DC_IRQ# */
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1100";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg3;
-
- prom_init_cmdline();
-
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
-
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
- /* Hit BCSR.RST_VDDI[SOFT_RESET] */
- au_writel(0x00000000, PB1100_RST_VDDI);
-}
-
-void __init board_setup(void)
-{
- volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
-
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- au_writel(0, SYS_PININPUTEN);
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
- {
- u32 pin_func, sys_freqctrl, sys_clksrc;
-
- /* Configure pins GPIO[14:9] as GPIO */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* Zero and disable USBH/USBD/IrDA clock */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
-
- /* FREQ2 = aux / 2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
- SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48 MHz FREQ2 into USBH/USBD/IrDA
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- /* Setup the static bus controller */
- au_writel(0x00000002, MEM_STCFG3); /* type = PCMCIA */
- au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
- au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
-
- /*
- * Get USB Functionality pin state (device vs host drive pins).
- */
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host. */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
- }
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled. */
- if (!(readb(base + 0x28) & 0x20)) {
- writeb(readb(base + 0x28) | 0x20, base + 0x28);
- au_sync();
- }
- /* Put the clock in BCD mode. */
- if (readb(base + 0x2C) & 0x4) { /* reg B */
- writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
- au_sync();
- }
-}
diff --git a/arch/mips/alchemy/pb1200/Makefile b/arch/mips/alchemy/pb1200/Makefile
deleted file mode 100644
index e9b9d27..0000000
--- a/arch/mips/alchemy/pb1200/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
-#
-
-lib-y := board_setup.o
-obj-y += platform.o
-
-EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/pb1200/board_setup.c b/arch/mips/alchemy/pb1200/board_setup.c
deleted file mode 100644
index a336a7a..0000000
--- a/arch/mips/alchemy/pb1200/board_setup.c
+++ /dev/null
@@ -1,316 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1200/Db1200 board setup.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-#include <prom.h>
-
-extern void (*board_init_irq)(void);
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- /* This is external interrupt cascade */
- { AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-/*
- * Support for External interrupts on the Pb1200 Development platform.
- */
-static volatile int pb1200_cascade_en;
-
-irqreturn_t pb1200_cascade_handler(int irq, void *dev_id)
-{
- unsigned short bisr = bcsr->int_status;
- int extirq_nr = 0;
-
- /* Clear all the edge interrupts. This has no effect on level. */
- bcsr->int_status = bisr;
- for ( ; bisr; bisr &= bisr - 1) {
- extirq_nr = PB1200_INT_BEGIN + __ffs(bisr);
- /* Ack and dispatch IRQ */
- do_IRQ(extirq_nr);
- }
-
- return IRQ_RETVAL(1);
-}
-
-inline void pb1200_enable_irq(unsigned int irq_nr)
-{
- bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
-}
-
-inline void pb1200_disable_irq(unsigned int irq_nr)
-{
- bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
- bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
-}
-
-static unsigned int pb1200_setup_cascade(void)
-{
- return request_irq(AU1000_GPIO_7, &pb1200_cascade_handler,
- 0, "Pb1200 Cascade", &pb1200_cascade_handler);
-}
-
-static unsigned int pb1200_startup_irq(unsigned int irq)
-{
- if (++pb1200_cascade_en == 1) {
- int res;
-
- res = pb1200_setup_cascade();
- if (res)
- return res;
- }
-
- pb1200_enable_irq(irq);
-
- return 0;
-}
-
-static void pb1200_shutdown_irq(unsigned int irq)
-{
- pb1200_disable_irq(irq);
- if (--pb1200_cascade_en == 0)
- free_irq(AU1000_GPIO_7, &pb1200_cascade_handler);
-}
-
-static struct irq_chip external_irq_type = {
-#ifdef CONFIG_MIPS_PB1200
- .name = "Pb1200 Ext",
-#endif
-#ifdef CONFIG_MIPS_DB1200
- .name = "Db1200 Ext",
-#endif
- .startup = pb1200_startup_irq,
- .shutdown = pb1200_shutdown_irq,
- .ack = pb1200_disable_irq,
- .mask = pb1200_disable_irq,
- .mask_ack = pb1200_disable_irq,
- .unmask = pb1200_enable_irq,
-};
-
-static void pb1200_init_irq(void)
-{
- unsigned int irq;
-
-#ifdef CONFIG_MIPS_PB1200
- /* We have a problem with CPLD rev 3. */
- if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
- printk(KERN_ERR "updated to latest revision. This software will\n");
- printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- printk(KERN_ERR "WARNING!!!\n");
- panic("Game over. Your score is 0.");
- }
-#endif
-
- for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++) {
- set_irq_chip_and_handler(irq, &external_irq_type,
- handle_level_irq);
- pb1200_disable_irq(irq);
- }
-
- /*
- * GPIO_7 can not be hooked here, so it is hooked upon first
- * request of any source attached to the cascade.
- */
-}
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1200";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x08000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
- bcsr->resets = 0;
- bcsr->system = 0;
-}
-
-void __init board_setup(void)
-{
- char *argptr = NULL;
-
-#if 0
- {
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
- }
-#endif
-
-#if defined(CONFIG_I2C_AU1550)
- {
- u32 freq0, clksrc;
- u32 pin_func;
-
- /* Select SMBus in CPLD */
- bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
-
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
- /* Set GPIOs correctly */
- pin_func |= 2 << 17;
- au_writel(pin_func, SYS_PINFUNC);
- au_sync();
-
- /* The I2C driver depends on 50 MHz clock */
- freq0 = au_readl(SYS_FREQCTRL0);
- au_sync();
- freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1);
- freq0 |= 3 << SYS_FC_FRDIV1_BIT;
- /* 396 MHz / (3 + 1) * 2 == 49.5 MHz */
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
- freq0 |= SYS_FC_FE1;
- au_writel(freq0, SYS_FREQCTRL0);
- au_sync();
-
- clksrc = au_readl(SYS_CLKSRC);
- au_sync();
- clksrc &= ~(SYS_CS_CE0 | SYS_CS_DE0 | SYS_CS_ME0_MASK);
- /* Bit 22 is EXTCLK0 for PSC0 */
- clksrc |= SYS_CS_MUX_FQ1 << SYS_CS_ME0_BIT;
- au_writel(clksrc, SYS_CLKSRC);
- au_sync();
- }
-#endif
-
-#ifdef CONFIG_FB_AU1200
- argptr = prom_getcmdline();
-#ifdef CONFIG_MIPS_PB1200
- strcat(argptr, " video=au1200fb:panel:bs");
-#endif
-#ifdef CONFIG_MIPS_DB1200
- strcat(argptr, " video=au1200fb:panel:bs");
-#endif
-#endif
-
- /*
- * The Pb1200 development board uses external MUX for PSC0 to
- * support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
- */
-#ifdef CONFIG_I2C_AU1550
- bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
-#endif
- au_sync();
-
-#ifdef CONFIG_MIPS_PB1200
- printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1200
- printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
-#endif
-
- /* Setup Pb1200 External Interrupt Controller */
- board_init_irq = pb1200_init_irq;
-}
-
-int board_au1200fb_panel(void)
-{
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
- int p;
-
- p = bcsr->switches;
- p >>= 8;
- p &= 0x0F;
- return p;
-}
-
-int board_au1200fb_panel_init(void)
-{
- /* Apply power */
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
- bcsr->board |= BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL;
- /* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
- return 0;
-}
-
-int board_au1200fb_panel_shutdown(void)
-{
- /* Remove power */
- BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
- bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
- BCSR_BOARD_LCDBL);
- /* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
- return 0;
-}
diff --git a/arch/mips/alchemy/pb1200/platform.c b/arch/mips/alchemy/pb1200/platform.c
deleted file mode 100644
index 9530329..0000000
--- a/arch/mips/alchemy/pb1200/platform.c
+++ /dev/null
@@ -1,166 +0,0 @@
-/*
- * Pb1200/DBAu1200 board platform device registration
- *
- * Copyright (C) 2008 MontaVista Software Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#include <linux/dma-mapping.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/platform_device.h>
-
-#include <asm/mach-au1x00/au1xxx.h>
-#include <asm/mach-au1x00/au1100_mmc.h>
-
-static int mmc_activity;
-
-static void pb1200mmc0_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr->board |= BCSR_BOARD_SD0PWR;
- else
- bcsr->board &= ~BCSR_BOARD_SD0PWR;
-
- au_sync_delay(1);
-}
-
-static int pb1200mmc0_card_readonly(void *mmc_host)
-{
- return (bcsr->status & BCSR_STATUS_SD0WP) ? 1 : 0;
-}
-
-static int pb1200mmc0_card_inserted(void *mmc_host)
-{
- return (bcsr->sig_status & BCSR_INT_SD0INSERT) ? 1 : 0;
-}
-
-static void pb1200_mmcled_set(struct led_classdev *led,
- enum led_brightness brightness)
-{
- if (brightness != LED_OFF) {
- if (++mmc_activity == 1)
- bcsr->disk_leds &= ~(1 << 8);
- } else {
- if (--mmc_activity == 0)
- bcsr->disk_leds |= (1 << 8);
- }
-}
-
-static struct led_classdev pb1200mmc_led = {
- .brightness_set = pb1200_mmcled_set,
-};
-
-#ifndef CONFIG_MIPS_DB1200
-static void pb1200mmc1_set_power(void *mmc_host, int state)
-{
- if (state)
- bcsr->board |= BCSR_BOARD_SD1PWR;
- else
- bcsr->board &= ~BCSR_BOARD_SD1PWR;
-
- au_sync_delay(1);
-}
-
-static int pb1200mmc1_card_readonly(void *mmc_host)
-{
- return (bcsr->status & BCSR_STATUS_SD1WP) ? 1 : 0;
-}
-
-static int pb1200mmc1_card_inserted(void *mmc_host)
-{
- return (bcsr->sig_status & BCSR_INT_SD1INSERT) ? 1 : 0;
-}
-#endif
-
-const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
- [0] = {
- .set_power = pb1200mmc0_set_power,
- .card_inserted = pb1200mmc0_card_inserted,
- .card_readonly = pb1200mmc0_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-#ifndef CONFIG_MIPS_DB1200
- [1] = {
- .set_power = pb1200mmc1_set_power,
- .card_inserted = pb1200mmc1_card_inserted,
- .card_readonly = pb1200mmc1_card_readonly,
- .cd_setup = NULL, /* use poll-timer in driver */
- .led = &pb1200mmc_led,
- },
-#endif
-};
-
-static struct resource ide_resources[] = {
- [0] = {
- .start = IDE_PHYS_ADDR,
- .end = IDE_PHYS_ADDR + IDE_PHYS_LEN - 1,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = IDE_INT,
- .end = IDE_INT,
- .flags = IORESOURCE_IRQ
- }
-};
-
-static u64 ide_dmamask = DMA_32BIT_MASK;
-
-static struct platform_device ide_device = {
- .name = "au1200-ide",
- .id = 0,
- .dev = {
- .dma_mask = &ide_dmamask,
- .coherent_dma_mask = DMA_32BIT_MASK,
- },
- .num_resources = ARRAY_SIZE(ide_resources),
- .resource = ide_resources
-};
-
-static struct resource smc91c111_resources[] = {
- [0] = {
- .name = "smc91x-regs",
- .start = SMC91C111_PHYS_ADDR,
- .end = SMC91C111_PHYS_ADDR + 0xf,
- .flags = IORESOURCE_MEM
- },
- [1] = {
- .start = SMC91C111_INT,
- .end = SMC91C111_INT,
- .flags = IORESOURCE_IRQ
- },
-};
-
-static struct platform_device smc91c111_device = {
- .name = "smc91x",
- .id = -1,
- .num_resources = ARRAY_SIZE(smc91c111_resources),
- .resource = smc91c111_resources
-};
-
-static struct platform_device *board_platform_devices[] __initdata = {
- &ide_device,
- &smc91c111_device
-};
-
-static int __init board_register_devices(void)
-{
- return platform_add_devices(board_platform_devices,
- ARRAY_SIZE(board_platform_devices));
-}
-
-arch_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/pb1500/Makefile b/arch/mips/alchemy/pb1500/Makefile
deleted file mode 100644
index 4664d61..0000000
--- a/arch/mips/alchemy/pb1500/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2001, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1500 board.
-#
-
-lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1500/board_setup.c b/arch/mips/alchemy/pb1500/board_setup.c
deleted file mode 100644
index 1be1afc..0000000
--- a/arch/mips/alchemy/pb1500/board_setup.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1500.h>
-#include <prom.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1500_GPIO_204, INTC_INT_HIGH_LEVEL, 0 },
- { AU1500_GPIO_201, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_202, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_203, INTC_INT_LOW_LEVEL, 0 },
- { AU1500_GPIO_205, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1500";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x04000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
- /* Hit BCSR.RST_VDDI[SOFT_RESET] */
- au_writel(0x00000000, PB1500_RST_VDDI);
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
- u32 sys_freqctrl, sys_clksrc;
-
- sys_clksrc = sys_freqctrl = pin_func = 0;
- /* Set AUX clock to 12 MHz * 8 = 96 MHz */
- au_writel(8, SYS_AUXPLL);
- au_writel(0, SYS_PINSTATERD);
- udelay(100);
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-
- /* GPIO201 is input for PCMCIA card detect */
- /* GPIO203 is input for PCMCIA interrupt request */
- au_writel(au_readl(GPIO2_DIR) & ~((1 << 1) | (1 << 3)), GPIO2_DIR);
-
- /* Zero and disable FREQ2 */
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /* zero and disable USBH/USBD clocks */
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- sys_freqctrl = au_readl(SYS_FREQCTRL0);
- sys_freqctrl &= ~0xFFF00000;
-
- sys_clksrc = au_readl(SYS_CLKSRC);
- sys_clksrc &= ~(SYS_CS_CUD | SYS_CS_DUD | SYS_CS_MUD_MASK |
- SYS_CS_CUH | SYS_CS_DUH | SYS_CS_MUH_MASK);
-
- /* FREQ2 = aux/2 = 48 MHz */
- sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) | SYS_FC_FE2 | SYS_FC_FS2;
- au_writel(sys_freqctrl, SYS_FREQCTRL0);
-
- /*
- * Route 48MHz FREQ2 into USB Host and/or Device
- */
- sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MUH_BIT;
- au_writel(sys_clksrc, SYS_CLKSRC);
-
- pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
- /* 2nd USB port is USB host */
- pin_func |= SYS_PF_USB;
- au_writel(pin_func, SYS_PINFUNC);
-#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
-
-#ifdef CONFIG_PCI
- /* Setup PCI bus controller */
- au_writel(0, Au1500_PCI_CMEM);
- au_writel(0x00003fff, Au1500_CFG_BASE);
-#if defined(__MIPSEB__)
- au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
-#else
- au_writel(0xf, Au1500_PCI_CFG);
-#endif
- au_writel(0xf0000000, Au1500_PCI_MWMASK_DEV);
- au_writel(0, Au1500_PCI_MWBASE_REV_CCL);
- au_writel(0x02a00356, Au1500_PCI_STATCMD);
- au_writel(0x00003c04, Au1500_PCI_HDRTYPE);
- au_writel(0x00000008, Au1500_PCI_MBAR);
- au_sync();
-#endif
-
- /* Enable sys bus clock divider when IDLE state or no bus activity. */
- au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
-
- /* Enable the RTC if not already enabled */
- if (!(au_readl(0xac000028) & 0x20)) {
- printk(KERN_INFO "enabling clock ...\n");
- au_writel((au_readl(0xac000028) | 0x20), 0xac000028);
- }
- /* Put the clock in BCD mode */
- if (au_readl(0xac00002c) & 0x4) { /* reg B */
- au_writel(au_readl(0xac00002c) & ~0x4, 0xac00002c);
- au_sync();
- }
-}
diff --git a/arch/mips/alchemy/pb1550/Makefile b/arch/mips/alchemy/pb1550/Makefile
deleted file mode 100644
index 7e6453d..0000000
--- a/arch/mips/alchemy/pb1550/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2000, 2008 MontaVista Software Inc.
-# Author: MontaVista Software, Inc. <source@mvista.com>
-#
-# Makefile for the Alchemy Semiconductor Pb1550 board.
-#
-
-lib-y := board_setup.o
diff --git a/arch/mips/alchemy/pb1550/board_setup.c b/arch/mips/alchemy/pb1550/board_setup.c
deleted file mode 100644
index e844484..0000000
--- a/arch/mips/alchemy/pb1550/board_setup.c
+++ /dev/null
@@ -1,97 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Alchemy Pb1550 board setup.
- *
- * Copyright 2000, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/kernel.h>
-#include <asm/bootinfo.h>
-#include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1550.h>
-#include <prom.h>
-
-char irq_tab_alchemy[][5] __initdata = {
- [12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
- [13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
- { AU1000_GPIO_0, INTC_INT_LOW_LEVEL, 0 },
- { AU1000_GPIO_1, INTC_INT_LOW_LEVEL, 0 },
-};
-
-int __initdata au1xxx_nr_irqs = ARRAY_SIZE(au1xxx_irq_map);
-
-
-const char *get_system_type(void)
-{
- return "Alchemy Pb1550";
-}
-
-void __init prom_init(void)
-{
- unsigned char *memsize_str;
- unsigned long memsize;
-
- prom_argc = (int)fw_arg0;
- prom_argv = (char **)fw_arg1;
- prom_envp = (char **)fw_arg2;
-
- prom_init_cmdline();
- memsize_str = prom_getenv("memsize");
- if (!memsize_str)
- memsize = 0x08000000;
- else
- strict_strtol(memsize_str, 0, &memsize);
- add_memory_region(0, memsize, BOOT_MEM_RAM);
-}
-
-void board_reset(void)
-{
- /* Hit BCSR.SYSTEM[RESET] */
- au_writew(au_readw(0xAF00001C) & ~BCSR_SYSTEM_RESET, 0xAF00001C);
-}
-
-void __init board_setup(void)
-{
- u32 pin_func;
-
- /*
- * Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
- * but it is board specific code, so put it here.
- */
- pin_func = au_readl(SYS_PINFUNC);
- au_sync();
- pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
- au_writel(pin_func, SYS_PINFUNC);
-
- au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
- au_sync();
-
- printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
-}
--
1.6.0.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 3/3] Alchemy: common reset code is evalboard code.
[not found] ` <cover.1226083170.git.mano@roarinelk.homelinux.net>
2008-11-07 18:41 ` [PATCH 1/3] Alchemy: merge small board files into single files Manuel Lauss
2008-11-07 18:41 ` [PATCH 2/3] Alchemy: Move evalboard code to common directory Manuel Lauss
@ 2008-11-07 18:41 ` Manuel Lauss
2008-11-07 23:11 ` Sergei Shtylyov
2 siblings, 1 reply; 7+ messages in thread
From: Manuel Lauss @ 2008-11-07 18:41 UTC (permalink / raw)
To: Linux-MIPS; +Cc: Manuel Lauss
Move common/reset.c contents to evalboard code where it belongs.
Add reboot hook initialization to mtx-1 and xxs1500 boards.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
---
arch/mips/alchemy/common/Makefile | 2 +-
arch/mips/alchemy/common/reset.c | 189 ------------------------------
arch/mips/alchemy/common/setup.c | 39 -------
arch/mips/alchemy/evalboards/common.c | 191 +++++++++++++++++++++++++++++++
arch/mips/alchemy/evalboards/db1x00.c | 4 +
arch/mips/alchemy/evalboards/pb1000.c | 3 +
arch/mips/alchemy/evalboards/pb1100.c | 3 +
arch/mips/alchemy/evalboards/pb1200.c | 3 +
arch/mips/alchemy/evalboards/pb1500.c | 3 +
arch/mips/alchemy/evalboards/pb1550.c | 3 +
arch/mips/alchemy/mtx-1/board_setup.c | 5 +-
arch/mips/alchemy/xxs1500/board_setup.c | 5 +-
12 files changed, 219 insertions(+), 231 deletions(-)
delete mode 100644 arch/mips/alchemy/common/reset.c
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index df48fd6..028e3b9 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -5,7 +5,7 @@
# Makefile for the Alchemy Au1xx0 CPUs, generic files.
#
-obj-y += prom.o irq.o puts.o time.o reset.o \
+obj-y += prom.o irq.o puts.o time.o \
au1xxx_irqmap.o clocks.o platform.o power.o setup.o \
sleeper.o cputable.o dma.o dbdma.o gpio.o
diff --git a/arch/mips/alchemy/common/reset.c b/arch/mips/alchemy/common/reset.c
deleted file mode 100644
index d555429..0000000
--- a/arch/mips/alchemy/common/reset.c
+++ /dev/null
@@ -1,189 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- * Au1xx0 reset routines.
- *
- * Copyright 2001, 2006, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <asm/cacheflush.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-extern int au_sleep(void);
-
-void au1000_restart(char *command)
-{
- /* Set all integrated peripherals to disabled states */
- extern void board_reset(void);
- u32 prid = read_c0_prid();
-
- printk(KERN_NOTICE "\n** Resetting Integrated Peripherals\n");
-
- switch (prid & 0xFF000000) {
- case 0x00000000: /* Au1000 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb0300040); /* ir_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb0520000); /* macen0 */
- au_writel(0x00, 0xb0520004); /* macen1 */
- au_writel(0x00, 0xb1000008); /* i2s_enable */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1300100); /* uart2_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x02, 0xb1600100); /* ssi0_enable */
- au_writel(0x02, 0xb1680100); /* ssi1_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x01000000: /* Au1500 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb1520000); /* macen0 */
- au_writel(0x00, 0xb1520004); /* macen1 */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x02000000: /* Au1100 */
- au_writel(0x02, 0xb0000010); /* ac97_enable */
- au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
- asm("sync");
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb0300040); /* ir_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb0520000); /* macen0 */
- au_writel(0x00, 0xb1000008); /* i2s_enable */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x02, 0xb1600100); /* ssi0_enable */
- au_writel(0x02, 0xb1680100); /* ssi1_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- case 0x03000000: /* Au1550 */
- au_writel(0x00, 0xb1a00004); /* psc 0 */
- au_writel(0x00, 0xb1b00004); /* psc 1 */
- au_writel(0x00, 0xb0a00004); /* psc 2 */
- au_writel(0x00, 0xb0b00004); /* psc 3 */
- au_writel(0x00, 0xb017fffc); /* usbh_enable */
- au_writel(0x00, 0xb0200058); /* usbd_enable */
- au_writel(0x00, 0xb4004104); /* mac dma */
- au_writel(0x00, 0xb4004114); /* mac dma */
- au_writel(0x00, 0xb4004124); /* mac dma */
- au_writel(0x00, 0xb4004134); /* mac dma */
- au_writel(0x00, 0xb1520000); /* macen0 */
- au_writel(0x00, 0xb1520004); /* macen1 */
- au_writel(0x00, 0xb1100100); /* uart0_enable */
- au_writel(0x00, 0xb1200100); /* uart1_enable */
- au_writel(0x00, 0xb1400100); /* uart3_enable */
- au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
- au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
- au_writel(0x00, 0xb1900028); /* sys_clksrc */
- au_writel(0x10, 0xb1900060); /* sys_cpupll */
- au_writel(0x00, 0xb1900064); /* sys_auxpll */
- au_writel(0x00, 0xb1900100); /* sys_pininputen */
- break;
- }
-
- set_c0_status(ST0_BEV | ST0_ERL);
- change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
- flush_cache_all();
- write_c0_wired(0);
-
- /* Give board a chance to do a hardware reset */
- board_reset();
-
- /* Jump to the beggining in case board_reset() is empty */
- __asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-void au1000_halt(void)
-{
-#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
- /* Power off system */
- printk(KERN_NOTICE "\n** Powering off...\n");
- au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
- au_sync();
- while (1); /* should not get here */
-#else
- printk(KERN_NOTICE "\n** You can safely turn off the power\n");
-#ifdef CONFIG_MIPS_MIRAGE
- au_writel((1 << 26) | (1 << 10), GPIO2_OUTPUT);
-#endif
-#ifdef CONFIG_MIPS_DB1200
- au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
-#endif
-#ifdef CONFIG_PM
- au_sleep();
-
- /* Should not get here */
- printk(KERN_ERR "Unable to put CPU in sleep mode\n");
- while (1);
-#else
- while (1)
- __asm__(".set\tmips3\n\t"
- "wait\n\t"
- ".set\tmips0");
-#endif
-#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
-}
-
-void au1000_power_off(void)
-{
- au1000_halt();
-}
diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
index 1ac6b06..cfb531e 100644
--- a/arch/mips/alchemy/common/setup.c
+++ b/arch/mips/alchemy/common/setup.c
@@ -28,25 +28,14 @@
#include <linux/init.h>
#include <linux/ioport.h>
#include <linux/module.h>
-#include <linux/pm.h>
-
-#include <asm/mipsregs.h>
-#include <asm/reboot.h>
-#include <asm/time.h>
-
#include <au1000.h>
-#include <prom.h>
extern void __init board_setup(void);
-extern void au1000_restart(char *);
-extern void au1000_halt(void);
-extern void au1000_power_off(void);
extern void set_cpuspec(void);
void __init plat_mem_setup(void)
{
struct cpu_spec *sp;
- char *argptr;
unsigned long prid, cpufreq, bclk;
set_cpuspec();
@@ -79,34 +68,6 @@ void __init plat_mem_setup(void)
/* Clear to obtain best system bus performance */
clear_c0_config(1 << 19); /* Clear Config[OD] */
- argptr = prom_getcmdline();
-
-#ifdef CONFIG_SERIAL_8250_CONSOLE
- argptr = strstr(argptr, "console=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- strcat(argptr, " console=ttyS0,115200");
- }
-#endif
-
-#ifdef CONFIG_FB_AU1100
- argptr = strstr(argptr, "video=");
- if (argptr == NULL) {
- argptr = prom_getcmdline();
- /* default panel */
- /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
- }
-#endif
-
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
- /* au1000 does not support vra, au1500 and au1100 do */
- strcat(argptr, " au1000_audio=vra");
- argptr = prom_getcmdline();
-#endif
- _machine_restart = au1000_restart;
- _machine_halt = au1000_halt;
- pm_power_off = au1000_power_off;
-
/* IO/MEM resources. */
set_io_port_base(0);
ioport_resource.start = IOPORT_RESOURCE_START;
diff --git a/arch/mips/alchemy/evalboards/common.c b/arch/mips/alchemy/evalboards/common.c
index d112fcf..7c78d54 100644
--- a/arch/mips/alchemy/evalboards/common.c
+++ b/arch/mips/alchemy/evalboards/common.c
@@ -29,10 +29,15 @@
#include <linux/init.h>
#include <linux/kernel.h>
+#include <linux/pm.h> /* pm_power_off */
#include <asm/bootinfo.h>
+#include <asm/cacheflush.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/reboot.h>
#include <prom.h>
+extern int au_sleep(void);
+
#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_DB1000) || \
defined(CONFIG_MIPS_PB1100) || defined(CONFIG_MIPS_DB1100) || \
defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_DB1500) || \
@@ -60,3 +65,189 @@ void __init prom_init(void)
strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
+
+static void evalboard_restart(char *command)
+{
+ /* Set all integrated peripherals to disabled states */
+ extern void board_reset(void);
+ u32 prid = read_c0_prid();
+
+ printk(KERN_NOTICE "\n** Resetting Integrated Peripherals\n");
+
+ switch (prid & 0xFF000000) {
+ case 0x00000000: /* Au1000 */
+ au_writel(0x02, 0xb0000010); /* ac97_enable */
+ au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
+ asm("sync");
+ au_writel(0x00, 0xb017fffc); /* usbh_enable */
+ au_writel(0x00, 0xb0200058); /* usbd_enable */
+ au_writel(0x00, 0xb0300040); /* ir_enable */
+ au_writel(0x00, 0xb4004104); /* mac dma */
+ au_writel(0x00, 0xb4004114); /* mac dma */
+ au_writel(0x00, 0xb4004124); /* mac dma */
+ au_writel(0x00, 0xb4004134); /* mac dma */
+ au_writel(0x00, 0xb0520000); /* macen0 */
+ au_writel(0x00, 0xb0520004); /* macen1 */
+ au_writel(0x00, 0xb1000008); /* i2s_enable */
+ au_writel(0x00, 0xb1100100); /* uart0_enable */
+ au_writel(0x00, 0xb1200100); /* uart1_enable */
+ au_writel(0x00, 0xb1300100); /* uart2_enable */
+ au_writel(0x00, 0xb1400100); /* uart3_enable */
+ au_writel(0x02, 0xb1600100); /* ssi0_enable */
+ au_writel(0x02, 0xb1680100); /* ssi1_enable */
+ au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
+ au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
+ au_writel(0x00, 0xb1900028); /* sys_clksrc */
+ au_writel(0x10, 0xb1900060); /* sys_cpupll */
+ au_writel(0x00, 0xb1900064); /* sys_auxpll */
+ au_writel(0x00, 0xb1900100); /* sys_pininputen */
+ break;
+ case 0x01000000: /* Au1500 */
+ au_writel(0x02, 0xb0000010); /* ac97_enable */
+ au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
+ asm("sync");
+ au_writel(0x00, 0xb017fffc); /* usbh_enable */
+ au_writel(0x00, 0xb0200058); /* usbd_enable */
+ au_writel(0x00, 0xb4004104); /* mac dma */
+ au_writel(0x00, 0xb4004114); /* mac dma */
+ au_writel(0x00, 0xb4004124); /* mac dma */
+ au_writel(0x00, 0xb4004134); /* mac dma */
+ au_writel(0x00, 0xb1520000); /* macen0 */
+ au_writel(0x00, 0xb1520004); /* macen1 */
+ au_writel(0x00, 0xb1100100); /* uart0_enable */
+ au_writel(0x00, 0xb1400100); /* uart3_enable */
+ au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
+ au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
+ au_writel(0x00, 0xb1900028); /* sys_clksrc */
+ au_writel(0x10, 0xb1900060); /* sys_cpupll */
+ au_writel(0x00, 0xb1900064); /* sys_auxpll */
+ au_writel(0x00, 0xb1900100); /* sys_pininputen */
+ break;
+ case 0x02000000: /* Au1100 */
+ au_writel(0x02, 0xb0000010); /* ac97_enable */
+ au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
+ asm("sync");
+ au_writel(0x00, 0xb017fffc); /* usbh_enable */
+ au_writel(0x00, 0xb0200058); /* usbd_enable */
+ au_writel(0x00, 0xb0300040); /* ir_enable */
+ au_writel(0x00, 0xb4004104); /* mac dma */
+ au_writel(0x00, 0xb4004114); /* mac dma */
+ au_writel(0x00, 0xb4004124); /* mac dma */
+ au_writel(0x00, 0xb4004134); /* mac dma */
+ au_writel(0x00, 0xb0520000); /* macen0 */
+ au_writel(0x00, 0xb1000008); /* i2s_enable */
+ au_writel(0x00, 0xb1100100); /* uart0_enable */
+ au_writel(0x00, 0xb1200100); /* uart1_enable */
+ au_writel(0x00, 0xb1400100); /* uart3_enable */
+ au_writel(0x02, 0xb1600100); /* ssi0_enable */
+ au_writel(0x02, 0xb1680100); /* ssi1_enable */
+ au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
+ au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
+ au_writel(0x00, 0xb1900028); /* sys_clksrc */
+ au_writel(0x10, 0xb1900060); /* sys_cpupll */
+ au_writel(0x00, 0xb1900064); /* sys_auxpll */
+ au_writel(0x00, 0xb1900100); /* sys_pininputen */
+ break;
+ case 0x03000000: /* Au1550 */
+ au_writel(0x00, 0xb1a00004); /* psc 0 */
+ au_writel(0x00, 0xb1b00004); /* psc 1 */
+ au_writel(0x00, 0xb0a00004); /* psc 2 */
+ au_writel(0x00, 0xb0b00004); /* psc 3 */
+ au_writel(0x00, 0xb017fffc); /* usbh_enable */
+ au_writel(0x00, 0xb0200058); /* usbd_enable */
+ au_writel(0x00, 0xb4004104); /* mac dma */
+ au_writel(0x00, 0xb4004114); /* mac dma */
+ au_writel(0x00, 0xb4004124); /* mac dma */
+ au_writel(0x00, 0xb4004134); /* mac dma */
+ au_writel(0x00, 0xb1520000); /* macen0 */
+ au_writel(0x00, 0xb1520004); /* macen1 */
+ au_writel(0x00, 0xb1100100); /* uart0_enable */
+ au_writel(0x00, 0xb1200100); /* uart1_enable */
+ au_writel(0x00, 0xb1400100); /* uart3_enable */
+ au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
+ au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
+ au_writel(0x00, 0xb1900028); /* sys_clksrc */
+ au_writel(0x10, 0xb1900060); /* sys_cpupll */
+ au_writel(0x00, 0xb1900064); /* sys_auxpll */
+ au_writel(0x00, 0xb1900100); /* sys_pininputen */
+ break;
+ }
+
+ set_c0_status(ST0_BEV | ST0_ERL);
+ change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
+ flush_cache_all();
+ write_c0_wired(0);
+
+ /* Give board a chance to do a hardware reset */
+ board_reset();
+
+ /* Jump to the beggining in case board_reset() is empty */
+ __asm__ __volatile__("jr\t%0" : : "r"(0xbfc00000));
+}
+
+static void evalboard_halt(void)
+{
+#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
+ /* Power off system */
+ printk(KERN_NOTICE "\n** Powering off...\n");
+ au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
+ au_sync();
+ while (1)
+ ; /* should not get here */
+#else
+ printk(KERN_NOTICE "\n** You can safely turn off the power\n");
+#ifdef CONFIG_MIPS_MIRAGE
+ au_writel((1 << 26) | (1 << 10), GPIO2_OUTPUT);
+#endif
+#ifdef CONFIG_MIPS_DB1200
+ au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
+#endif
+#ifdef CONFIG_PM
+ au_sleep();
+
+ /* Should not get here */
+ printk(KERN_ERR "Unable to put CPU in sleep mode\n");
+ while (1)
+ ;
+#else
+ while (1)
+ __asm__(".set\tmips3\n\t"
+ "wait\n\t"
+ ".set\tmips0");
+#endif
+#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
+}
+
+void __init evalboard_common_init(void)
+{
+ char *argptr;
+
+ argptr = prom_getcmdline();
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+ argptr = strstr(argptr, "console=");
+ if (argptr == NULL) {
+ argptr = prom_getcmdline();
+ strcat(argptr, " console=ttyS0,115200");
+ }
+#endif
+
+#ifdef CONFIG_FB_AU1100
+ argptr = strstr(argptr, "video=");
+ if (argptr == NULL) {
+ argptr = prom_getcmdline();
+ /* default panel */
+ /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
+ }
+#endif
+
+#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
+ /* au1000 does not support vra, au1500 and au1100 do */
+ strcat(argptr, " au1000_audio=vra");
+ argptr = prom_getcmdline();
+#endif
+
+ _machine_restart = evalboard_restart;
+ _machine_halt = evalboard_halt;
+ pm_power_off = evalboard_halt;
+}
diff --git a/arch/mips/alchemy/evalboards/db1x00.c b/arch/mips/alchemy/evalboards/db1x00.c
index 868ad3e..997c8a3 100644
--- a/arch/mips/alchemy/evalboards/db1x00.c
+++ b/arch/mips/alchemy/evalboards/db1x00.c
@@ -36,6 +36,8 @@
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-db1x00/db1x00.h>
+#include "common.h"
+
#ifdef CONFIG_MIPS_DB1500
char irq_tab_alchemy[][5] __initdata = {
[12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371 */
@@ -114,6 +116,8 @@ void __init board_setup(void)
pin_func = 0;
+ evalboard_common_init();
+
/* Not valid for Au1550 */
#if defined(CONFIG_IRDA) && \
(defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1100))
diff --git a/arch/mips/alchemy/evalboards/pb1000.c b/arch/mips/alchemy/evalboards/pb1000.c
index e795eaf..96354bf 100644
--- a/arch/mips/alchemy/evalboards/pb1000.c
+++ b/arch/mips/alchemy/evalboards/pb1000.c
@@ -28,6 +28,7 @@
#include <linux/kernel.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1000.h>
+#include "common.h"
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_15, INTC_INT_LOW_LEVEL, 0 },
@@ -52,6 +53,8 @@ void __init board_setup(void)
sys_freqctrl = sys_clksrc = 0;
+ evalboard_common_init();
+
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PINSTATERD);
diff --git a/arch/mips/alchemy/evalboards/pb1100.c b/arch/mips/alchemy/evalboards/pb1100.c
index dbd9605..3177deb 100644
--- a/arch/mips/alchemy/evalboards/pb1100.c
+++ b/arch/mips/alchemy/evalboards/pb1100.c
@@ -28,6 +28,7 @@
#include <linux/kernel.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1100.h>
+#include "common.h"
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
{ AU1000_GPIO_9, INTC_INT_LOW_LEVEL, 0 }, /* PCMCIA Card Fully_Inserted# */
@@ -54,6 +55,8 @@ void __init board_setup(void)
{
volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+ evalboard_common_init();
+
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
au_writel(0, SYS_PININPUTEN);
diff --git a/arch/mips/alchemy/evalboards/pb1200.c b/arch/mips/alchemy/evalboards/pb1200.c
index 4a24874..1ed54b5 100644
--- a/arch/mips/alchemy/evalboards/pb1200.c
+++ b/arch/mips/alchemy/evalboards/pb1200.c
@@ -39,6 +39,7 @@
#endif
#include <prom.h>
+#include "common.h"
extern void (*board_init_irq)(void);
@@ -184,6 +185,8 @@ void __init board_setup(void)
strcat(argptr, " video=au1200fb:panel:bs");
#endif
+ evalboard_common_init();
+
#if 0
{
u32 pin_func;
diff --git a/arch/mips/alchemy/evalboards/pb1500.c b/arch/mips/alchemy/evalboards/pb1500.c
index 72c5222..0187bc5 100644
--- a/arch/mips/alchemy/evalboards/pb1500.c
+++ b/arch/mips/alchemy/evalboards/pb1500.c
@@ -28,6 +28,7 @@
#include <linux/kernel.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1500.h>
+#include "common.h"
char irq_tab_alchemy[][5] __initdata = {
[12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT370 */
@@ -61,6 +62,8 @@ void __init board_setup(void)
u32 pin_func;
u32 sys_freqctrl, sys_clksrc;
+ evalboard_common_init();
+
sys_clksrc = sys_freqctrl = pin_func = 0;
/* Set AUX clock to 12 MHz * 8 = 96 MHz */
au_writel(8, SYS_AUXPLL);
diff --git a/arch/mips/alchemy/evalboards/pb1550.c b/arch/mips/alchemy/evalboards/pb1550.c
index 15bcf6b..f475791 100644
--- a/arch/mips/alchemy/evalboards/pb1550.c
+++ b/arch/mips/alchemy/evalboards/pb1550.c
@@ -31,6 +31,7 @@
#include <linux/kernel.h>
#include <asm/mach-au1x00/au1000.h>
#include <asm/mach-pb1x00/pb1550.h>
+#include "common.h"
char irq_tab_alchemy[][5] __initdata = {
[12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
@@ -60,6 +61,8 @@ void __init board_setup(void)
{
u32 pin_func;
+ evalboard_common_init();
+
/*
* Enable PSC1 SYNC for AC'97. Normaly done in audio driver,
* but it is board specific code, so put it here.
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
index 2e26465..4712ce4 100644
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ b/arch/mips/alchemy/mtx-1/board_setup.c
@@ -33,6 +33,7 @@
#include <linux/kernel.h>
#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/reboot.h>
#include <prom.h>
extern int (*board_pci_idsel)(unsigned int devsel, int assert);
@@ -84,7 +85,7 @@ void __init prom_init(void)
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
-void board_reset(void)
+void board_reset(char *c)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
@@ -122,6 +123,8 @@ void __init board_setup(void)
board_pci_idsel = mtx1_pci_idsel;
+ _machine_restart = board_reset;
+
printk(KERN_INFO "4G Systems MTX-1 Board\n");
}
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index 813668f..effb538 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -29,6 +29,7 @@
#include <linux/kernel.h>
#include <asm/bootinfo.h>
#include <asm/mach-au1x00/au1000.h>
+#include <asm/reboot.h>
#include <prom.h>
struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
@@ -74,7 +75,7 @@ void __init prom_init(void)
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
-void board_reset(void)
+void board_reset(char *c)
{
/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
au_writel(0x00000000, 0xAE00001C);
@@ -122,4 +123,6 @@ void __init board_setup(void)
au_writel(0xf, Au1500_PCI_CFG);
#endif
#endif
+
+ _machine_restart = board_reset;
}
--
1.6.0.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH 3/3] Alchemy: common reset code is evalboard code.
2008-11-07 18:41 ` [PATCH 3/3] Alchemy: common reset code is evalboard code Manuel Lauss
@ 2008-11-07 23:11 ` Sergei Shtylyov
2008-11-08 5:54 ` Manuel Lauss
0 siblings, 1 reply; 7+ messages in thread
From: Sergei Shtylyov @ 2008-11-07 23:11 UTC (permalink / raw)
To: Manuel Lauss; +Cc: Linux-MIPS
Hello.
Manuel Lauss wrote:
> Move common/reset.c contents to evalboard code where it belongs.
>
I'm not sure it belongs there...
> Add reboot hook initialization to mtx-1 and xxs1500 boards.
>
> Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
That's all good but doesn't look equivalent to the old code...
> diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
> index 1ac6b06..cfb531e 100644
> --- a/arch/mips/alchemy/common/setup.c
> +++ b/arch/mips/alchemy/common/setup.c
> @@ -28,25 +28,14 @@
> #include <linux/init.h>
> #include <linux/ioport.h>
> #include <linux/module.h>
> -#include <linux/pm.h>
> -
> -#include <asm/mipsregs.h>
> -#include <asm/reboot.h>
> -#include <asm/time.h>
> -
> #include <au1000.h>
> -#include <prom.h>
>
> extern void __init board_setup(void);
> -extern void au1000_restart(char *);
> -extern void au1000_halt(void);
> -extern void au1000_power_off(void);
> extern void set_cpuspec(void);
>
> void __init plat_mem_setup(void)
> {
> struct cpu_spec *sp;
> - char *argptr;
> unsigned long prid, cpufreq, bclk;
>
> set_cpuspec();
> @@ -79,34 +68,6 @@ void __init plat_mem_setup(void)
> /* Clear to obtain best system bus performance */
> clear_c0_config(1 << 19); /* Clear Config[OD] */
>
> - argptr = prom_getcmdline();
> -
> -#ifdef CONFIG_SERIAL_8250_CONSOLE
> - argptr = strstr(argptr, "console=");
> - if (argptr == NULL) {
> - argptr = prom_getcmdline();
> - strcat(argptr, " console=ttyS0,115200");
> - }
> -#endif
> -
> -#ifdef CONFIG_FB_AU1100
> - argptr = strstr(argptr, "video=");
> - if (argptr == NULL) {
> - argptr = prom_getcmdline();
> - /* default panel */
> - /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
> - }
> -#endif
> -
> -#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
> - /* au1000 does not support vra, au1500 and au1100 do */
> - strcat(argptr, " au1000_audio=vra");
> - argptr = prom_getcmdline();
> -#endif
> - _machine_restart = au1000_restart;
> - _machine_halt = au1000_halt;
> - pm_power_off = au1000_power_off;
> -
> /* IO/MEM resources. */
> set_io_port_base(0);
> ioport_resource.start = IOPORT_RESOURCE_START;
>
How is this change related to the patch's purpose?
> diff --git a/arch/mips/alchemy/evalboards/common.c b/arch/mips/alchemy/evalboards/common.c
> index d112fcf..7c78d54 100644
> --- a/arch/mips/alchemy/evalboards/common.c
> +++ b/arch/mips/alchemy/evalboards/common.c
>
[...]
> +static void evalboard_halt(void)
> +{
> +#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
> + /* Power off system */
> + printk(KERN_NOTICE "\n** Powering off...\n");
> + au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
> + au_sync();
> + while (1)
> + ; /* should not get here */
> +#else
> + printk(KERN_NOTICE "\n** You can safely turn off the power\n");
> +#ifdef CONFIG_MIPS_MIRAGE
> + au_writel((1 << 26) | (1 << 10), GPIO2_OUTPUT);
> +#endif
> +#ifdef CONFIG_MIPS_DB1200
> + au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
> +#endif
> +#ifdef CONFIG_PM
> + au_sleep();
> +
> + /* Should not get here */
> + printk(KERN_ERR "Unable to put CPU in sleep mode\n");
> + while (1)
> + ;
> +#else
> + while (1)
> + __asm__(".set\tmips3\n\t"
> + "wait\n\t"
> + ".set\tmips0");
> +#endif
> +#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
> +}
>
So you moved this code only to leave the board specific #ifdef'ery
where it was? ;-)
> +
> +void __init evalboard_common_init(void)
> +{
> + char *argptr;
> +
> + argptr = prom_getcmdline();
> +
> +#ifdef CONFIG_SERIAL_8250_CONSOLE
> + argptr = strstr(argptr, "console=");
> + if (argptr == NULL) {
> + argptr = prom_getcmdline();
> + strcat(argptr, " console=ttyS0,115200");
> + }
> +#endif
> +
> +#ifdef CONFIG_FB_AU1100
> + argptr = strstr(argptr, "video=");
> + if (argptr == NULL) {
> + argptr = prom_getcmdline();
> + /* default panel */
> + /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
> + }
> +#endif
> +
> +#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
> + /* au1000 does not support vra, au1500 and au1100 do */
> + strcat(argptr, " au1000_audio=vra");
> + argptr = prom_getcmdline();
> +#endif
>
This probably needs to be in another patch...
> + _machine_restart = evalboard_restart;
>
I'm not sure that the name fits well since there's nothing board
specific in this particular function, just SoC specific...
> diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
> index 2e26465..4712ce4 100644
> --- a/arch/mips/alchemy/mtx-1/board_setup.c
> +++ b/arch/mips/alchemy/mtx-1/board_setup.c
> @@ -122,6 +123,8 @@ void __init board_setup(void)
>
> board_pci_idsel = mtx1_pci_idsel;
>
> + _machine_restart = board_reset;
>
Hey, that bypasses the restart code that was executed before this
patch...
WBR, Sergei
^ permalink raw reply [flat|nested] 7+ messages in thread* Re: [PATCH 3/3] Alchemy: common reset code is evalboard code.
2008-11-07 23:11 ` Sergei Shtylyov
@ 2008-11-08 5:54 ` Manuel Lauss
0 siblings, 0 replies; 7+ messages in thread
From: Manuel Lauss @ 2008-11-08 5:54 UTC (permalink / raw)
To: Sergei Shtylyov; +Cc: Linux-MIPS
On Sat, 08 Nov 2008 02:11:42 +0300
Sergei Shtylyov <sshtylyov@ru.mvista.com> wrote:
> Hello.
>
> Manuel Lauss wrote:
>
> > Move common/reset.c contents to evalboard code where it belongs.
> >
>
> I'm not sure it belongs there...
Oh yes it does (most of it, anyway). From my
"Im-not-a-au1200-evalboard" perspective most of the code in
alchemy/common is crap/hackery for the evalboards. reset.c is such a
case. I want it gone ;-) (just like common/platform.c).
> > Add reboot hook initialization to mtx-1 and xxs1500 boards.
> >
> > Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
>
> That's all good but doesn't look equivalent to the old code...
cf. end of this mail
> > diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
> > index 1ac6b06..cfb531e 100644
> > --- a/arch/mips/alchemy/common/setup.c
> > +++ b/arch/mips/alchemy/common/setup.c
> > @@ -28,25 +28,14 @@
> > #include <linux/init.h>
> > #include <linux/ioport.h>
> > #include <linux/module.h>
> > -#include <linux/pm.h>
> > -
> > -#include <asm/mipsregs.h>
> > -#include <asm/reboot.h>
> > -#include <asm/time.h>
> > -
> > #include <au1000.h>
> > -#include <prom.h>
> >
> > extern void __init board_setup(void);
> > -extern void au1000_restart(char *);
> > -extern void au1000_halt(void);
> > -extern void au1000_power_off(void);
> > extern void set_cpuspec(void);
> >
> > void __init plat_mem_setup(void)
> > {
> > struct cpu_spec *sp;
> > - char *argptr;
> > unsigned long prid, cpufreq, bclk;
> >
> > set_cpuspec();
> > @@ -79,34 +68,6 @@ void __init plat_mem_setup(void)
> > /* Clear to obtain best system bus performance */
> > clear_c0_config(1 << 19); /* Clear Config[OD] */
> >
> > - argptr = prom_getcmdline();
> > -
> > -#ifdef CONFIG_SERIAL_8250_CONSOLE
> > - argptr = strstr(argptr, "console=");
> > - if (argptr == NULL) {
> > - argptr = prom_getcmdline();
> > - strcat(argptr, " console=ttyS0,115200");
> > - }
> > -#endif
> > -
> > -#ifdef CONFIG_FB_AU1100
> > - argptr = strstr(argptr, "video=");
> > - if (argptr == NULL) {
> > - argptr = prom_getcmdline();
> > - /* default panel */
> > - /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
> > - }
> > -#endif
> > -
> > -#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
> > - /* au1000 does not support vra, au1500 and au1100 do */
> > - strcat(argptr, " au1000_audio=vra");
> > - argptr = prom_getcmdline();
> > -#endif
> > - _machine_restart = au1000_restart;
> > - _machine_halt = au1000_halt;
> > - pm_power_off = au1000_power_off;
> > -
> > /* IO/MEM resources. */
> > set_io_port_base(0);
> > ioport_resource.start = IOPORT_RESOURCE_START;
> >
>
> How is this change related to the patch's purpose?
Agrees, most belongs in the previous patch
> > diff --git a/arch/mips/alchemy/evalboards/common.c b/arch/mips/alchemy/evalboards/common.c
> > index d112fcf..7c78d54 100644
> > --- a/arch/mips/alchemy/evalboards/common.c
> > +++ b/arch/mips/alchemy/evalboards/common.c
> >
> [...]
> > +static void evalboard_halt(void)
> > +{
> > +#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
> > + /* Power off system */
> > + printk(KERN_NOTICE "\n** Powering off...\n");
> > + au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
> > + au_sync();
> > + while (1)
> > + ; /* should not get here */
> > +#else
> > + printk(KERN_NOTICE "\n** You can safely turn off the power\n");
> > +#ifdef CONFIG_MIPS_MIRAGE
> > + au_writel((1 << 26) | (1 << 10), GPIO2_OUTPUT);
> > +#endif
> > +#ifdef CONFIG_MIPS_DB1200
> > + au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
> > +#endif
> > +#ifdef CONFIG_PM
> > + au_sleep();
> > +
> > + /* Should not get here */
> > + printk(KERN_ERR "Unable to put CPU in sleep mode\n");
> > + while (1)
> > + ;
> > +#else
> > + while (1)
> > + __asm__(".set\tmips3\n\t"
> > + "wait\n\t"
> > + ".set\tmips0");
> > +#endif
> > +#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
> > +}
> >
>
> So you moved this code only to leave the board specific #ifdef'ery
> where it was? ;-)
Read the patch description: I just moved it out of common. If you
prefer I could remove this block and add shutdown/reboot hooks in every
board file.
> > +
> > +void __init evalboard_common_init(void)
> > +{
> > + char *argptr;
> > +
> > + argptr = prom_getcmdline();
> > +
> > +#ifdef CONFIG_SERIAL_8250_CONSOLE
> > + argptr = strstr(argptr, "console=");
> > + if (argptr == NULL) {
> > + argptr = prom_getcmdline();
> > + strcat(argptr, " console=ttyS0,115200");
> > + }
> > +#endif
> > +
> > +#ifdef CONFIG_FB_AU1100
> > + argptr = strstr(argptr, "video=");
> > + if (argptr == NULL) {
> > + argptr = prom_getcmdline();
> > + /* default panel */
> > + /*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
> > + }
> > +#endif
> > +
> > +#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
> > + /* au1000 does not support vra, au1500 and au1100 do */
> > + strcat(argptr, " au1000_audio=vra");
> > + argptr = prom_getcmdline();
> > +#endif
> >
>
> This probably needs to be in another patch...
Agreed,
> > + _machine_restart = evalboard_restart;
> >
>
> I'm not sure that the name fits well since there's nothing board
> specific in this particular function, just SoC specific...
My custom au1200 platform reboots just fine without this (as
does the DB1200), and the only in-tree users seem to be the
evalboards.
> > diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
> > index 2e26465..4712ce4 100644
> > --- a/arch/mips/alchemy/mtx-1/board_setup.c
> > +++ b/arch/mips/alchemy/mtx-1/board_setup.c
> > @@ -122,6 +123,8 @@ void __init board_setup(void)
> >
> > board_pci_idsel = mtx1_pci_idsel;
> >
> > + _machine_restart = board_reset;
> >
>
> Hey, that bypasses the restart code that was executed before this
> patch...
Yes, but are you absolutely sure its really necessary? I never had any
problems rebooting through the _machine_restart function without that
removed code on the DB1200 or my other AU1200 platform. Especially
since the default platform init file in yamon takes care of what the
now-bypassed code did (of course I don't know that in the MTX-1/XXS1500
case but I hope the designers of those boards just modified an existing
demoboard init file).
Do you have access to any of the not-DB1200 testboards? Can you please
test whether reboot/shutdown still works after this change?
Thank you!
Manuel Lauss
^ permalink raw reply [flat|nested] 7+ messages in thread