* PCMCIA genric sreail or modem support for db1100 bord
@ 2004-08-20 5:19 safiudeen Ts
0 siblings, 0 replies; 3+ messages in thread
From: safiudeen Ts @ 2004-08-20 5:19 UTC (permalink / raw)
To: linux-mips, ecartis; +Cc: safiudeen
I am trying to make a pcmcia serial card to work with DB 1100 development
bord mips prcessor mips au1100 runnning on linux 2.4.20
same pcmcia serial card works fine with my laptop running on linux 2.4.20-8
when try with db1100 it look like hanging in close
the test results are as follows
1) when I plug the card, cardmanegr start it gives thettyS4 at port
0xc00703f8 and the irq 34
2) then card manager calls /etc/pcmcia/serial start /dev/ttvS4
here it try to set the irq with o through the setserial,this give
"resource busy or unavailable error"
3)I changed /etc/pcmcia/serial so that setserial in /etc/pcmcia/serial can
set irq 3
after this when I remove the card and plug again, same port number and
irq is set, then
/etc/pcmcia/serial start /dev/ttvS4 runs , here it wait until press
enter to return to prompt
4) now I used set seril to see the status out put is this
# setserial -a /dev/ttyS4
/dev/ttyS4, Line 4, UART: 16550, Port: 0xc00703f8, IRQ: 34
Baud_base: 6188044, close_delay: 50, divisor: 0
closing_wait: 3000, closing_wait2: infinte
Flags: spd_normal skip_tes
and I checked /var/run/stab this is the out put
# cat /var/run/stab
Socket 0: Serial or Modem
0 serial serial_cs 0 ttyS4 4 68
Socket 1: empty
at this place evry thing look like ok
5) I run a smale serial prot test program it set the boud rate 9600, data
bit 8 stop bit 1 , no parity
, open the ttyS4 with the following options O_RDWR | O_NOCTTY |
O_NONBLOCK
write teststring of correctors to the ttyS4, and close.
open and write functions return no error, the write function retunr
the no. of bit writen correctly
close function hangs here I connected other side of the serial port
to a pc and started the minicom here I did'nt get any charecter writen to
the port
6) I checked there irq usage in /proc/interrupts this is the result
cat /proc/interrupts
# cat /proc/interrupts
CPU0
0: 11914 Au1000 Level serial
2: 0 Au1000 Level MMC
6: 0 Au1000 Level audio DAC
7: 0 Au1000 Level audio ADC
8: 0 Au1000 Level EP0 IN WR
9: 0 Au1000 Level EP1 IN WR
10: 0 Au1000 Level EP2 IN WR
22: 22518 Au1000 Level irda0
23: 0 Au1000 Level irda0
24: 0 Au1000 Rise Edge AU1100UDC Req
25: 0 Au1000 Rise Edge AU1100UDC Sus
26: 0 Au1000 Level usb-ohci
28: 8155 Au1000 Level eth0
34: 0 Au1000 Level serial
ERR: 0
it shows no any interupts happen to 34,
what should be the real problem ? if any one succeded in PCMCIA up with
db1100 development please can you tell me the way to
configure the kernela and the the importan settings
if anyone succeded in bringing up PCMCIA serial or modem driver serial_cs
working with this plartform
please help me in this regards
thanx
safiudeen
_________________________________________________________________
Tired of spam? Get advanced junk mail protection with MSN 8.
http://join.msn.com/?page=features/junkmail
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: PCMCIA genric sreail or modem support for db1100 bord
@ 2004-08-20 8:51 safiudeen Ts
2004-08-20 12:59 ` Michael Kelly
0 siblings, 1 reply; 3+ messages in thread
From: safiudeen Ts @ 2004-08-20 8:51 UTC (permalink / raw)
To: michael.stickel, linux-mips
built in serial ports are working fine in DB1100 with linux-2.4.20 kernel
When we use a pcmcia serial card or modem, for most of the card, cardmaneger
load serial_cs.o (actualy it uses the serial.o fetures for registering the
module).
This method work fine in my laptop.
same think hepens in db1100 bord also. I gues serial.o in bord db110 does'nt
support well for serial_cs
.
If there is a stand alon serial_cs.o module for this board It may work
without any problem.
if it is os where can I get the seria_cs or any generic serial pcmcia
driver for db1100 bord, or otherwise is any serial.c available for db1100
that can support pcmcia and inbuild serial as it works in labtop.
There is important think, when we connected in the laptop this pcmcia serial
card detect is detected as 65550A but in the board it detected as 65550. I
checked the serial.c code of db1100 there is no entry for this 65550A.
if any one worked with this DB1100 please help me to solve this problem
thanx
safiudeen
>From: Michael Stickel <michael.stickel@4g-systems.biz>
>To: "safiudeen Ts" <safiudeen@hotmail.com>
>Subject: Re: PCMCIA genric sreail or modem support for db1100 bord
>Date: Fri, 20 Aug 2004 10:07:40 +0200
>
>
>Do you use the buildin serial ports?
>
>My last information is that the au1x00-serial module does not work
>in parallel with the serial module because au1x00-serial.c is just a
>modified copy of serial.c.
>
>Michael
>
_________________________________________________________________
Add photos to your messages with MSN 8. Get 2 months FREE*.
http://join.msn.com/?page=features/featuredemail
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: PCMCIA genric sreail or modem support for db1100 bord
2004-08-20 8:51 PCMCIA genric sreail or modem support for db1100 bord safiudeen Ts
@ 2004-08-20 12:59 ` Michael Kelly
0 siblings, 0 replies; 3+ messages in thread
From: Michael Kelly @ 2004-08-20 12:59 UTC (permalink / raw)
To: safiudeen Ts; +Cc: michael.stickel, linux-mips
Safiudeen,
There is a known problem with some 8-bit cards and the Au1xxx family.
The following is from the FAQ for Linux that comes with the DB1100 CD:
============================================================
25) Which PCMCIA cards work with Au1x00/Pb1x00 Linux?
The Au1x00/Pb1x00 Linux PCMCIA cardmgr has been tested and known to
work with the following PC Cards. The Linux PCMCIA driver module is
listed to the left:
ide_cs.o Ritek Corporation, ATA DISK drive (3.3V Compact Flash Adapter)
ide_cs.o Butterfly Group 64M ATA disk drive (3.3V)
ide_cs.o SanDisk 192MB FlashDisk ATA (3.3/5V)
ide_cs.o SanDisk 10MB FlashDisk ATA (5V)
ide_cs.o Hitach 64MB flash card (3.3/5V)
ide_cs.o IO Data 256MB flash card (3.3/5V)
ide_cs.o Toshiba 2GB hard drive (actual tiny drive, like the IBM
MicroDrive) (3.3V/5V)
ide_cs.o IBM Microdrive
3c589.o 3COM 589 Ethernet card (5V)
pcnet_cs.o Linksys Network Everywhere NP10T
pcnet_cs.o Corega Ether PCC-TD
pcnet_cs.o Corega FEther PCC-TXD
pcnet_cs.o Laneed LD-CDL/T
axnet_cs.o Buffalo Tough Connect LPC3-CLX
NOTE: The Au1000 and Au1500 require an 8-bit PCMCIA HBA work around
be implemented on the board in order for 8-bit cards (i.e. pcnet_cs.o)
to work properly. See app note "Au1000 8-bit PCMCIA HBA".
============================================================\
IIRC most serial cards are 8-bit.
Hope this helps,
Michael
At 04:51 AM 8/20/2004, safiudeen Ts wrote:
>built in serial ports are working fine in DB1100 with linux-2.4.20 kernel
>When we use a pcmcia serial card or modem, for most of the card,
>cardmaneger load serial_cs.o (actualy it uses the serial.o fetures for
>registering the module).
>This method work fine in my laptop.
>same think hepens in db1100 bord also. I gues serial.o in bord db110
>does'nt support well for serial_cs
>.
>If there is a stand alon serial_cs.o module for this board It may work
>without any problem.
>if it is os where can I get the seria_cs or any generic serial pcmcia
>driver for db1100 bord, or otherwise is any serial.c available for db1100
>that can support pcmcia and inbuild serial as it works in labtop.
>
>There is important think, when we connected in the laptop this pcmcia
>serial card detect is detected as 65550A but in the board it detected as
>65550. I checked the serial.c code of db1100 there is no entry for this 65550A.
>
>if any one worked with this DB1100 please help me to solve this problem
>
>
>thanx
>safiudeen
>
>>From: Michael Stickel <michael.stickel@4g-systems.biz>
>>To: "safiudeen Ts" <safiudeen@hotmail.com>
>>Subject: Re: PCMCIA genric sreail or modem support for db1100 bord
>>Date: Fri, 20 Aug 2004 10:07:40 +0200
>>
>>
>>Do you use the buildin serial ports?
>>
>>My last information is that the au1x00-serial module does not work
>>in parallel with the serial module because au1x00-serial.c is just a
>>modified copy of serial.c.
>>
>>Michael
>>
>
>_________________________________________________________________
>Add photos to your messages with MSN 8. Get 2 months FREE*.
>http://join.msn.com/?page=features/featuredemail
>
Michael J. Kelly
VP Engineering/Marketing
Cogent Computer Systems, Inc.
1130 Ten Rod Road
Suite A-201
North Kingstown, RI 02852
tel:401-295-6505 fax:401-295-6507
www.cogcomp.com
alternate email: mkelly6505@hotmail.com
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2004-08-20 12:59 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2004-08-20 8:51 PCMCIA genric sreail or modem support for db1100 bord safiudeen Ts
2004-08-20 12:59 ` Michael Kelly
-- strict thread matches above, loose matches on Subject: below --
2004-08-20 5:19 safiudeen Ts
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox