From: "Heiko Stübner" <heiko@sntech.de>
To: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Beomho Seo <beomho.seo@samsung.com>, Chris Ball <cjb@laptop.org>,
"linux-mmc@vger.kernel.org" <linux-mmc@vger.kernel.org>,
myungjoo.ham@samsung.com
Subject: Re: [PATCH v2] mmc: sdhci-s3c: Use mmc_gpio_request_cd fuction
Date: Mon, 18 Nov 2013 21:03:17 +0100 [thread overview]
Message-ID: <201311182103.17626.heiko@sntech.de> (raw)
In-Reply-To: <5289A257.7090506@samsung.com>
Hi Jaehoon,
Am Montag, 18. November 2013, 06:15:03 schrieb Jaehoon Chung:
> Didn't have Any other comment for this patch?
> If don't have any other comment, i want this patch is submitted at
> mmc-next.
>
> We had tested this patch with exynos4 series.
>
> CC'd Heiko.
I don't have access to my s3c2416 machine this week, so I'll be able to test
this next week at the earliest.
I also found a small spelling mistake below.
Heiko
>
> Best Regards,
> Jaehoon Chung
>
> On 11/05/2013 08:48 PM, Beomho Seo wrote:
> > Hello all,
> >
> > I have revised some issues of v1 revision.
> > This patch used mmc_gpio_request_cd function for detect card from cd-gpio
> > pin. Please give your feedback at that time.
> >
> > Change from v2 to v1
> >
> > - Remove "return ret;" from "err_req_cd:".
> > - Revised sdhci_s3c_remove function.
> >
> > Subject: [PATCH] mmc: sdhci-s3c: Use mmc_gpio_request_cd function
> >
> > Include slot-gpio header file.
> > Use mmc_gpio_request_cd function.
> > Remove sehci_s3c_setup_card_detect_gpio/card_detect_thread functions.
^sdhci
> >
> > Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
> > Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
> > ---
> >
> > drivers/mmc/host/sdhci-s3c.c | 56
> > +++++++++++------------------------------- 1 file changed, 14
> > insertions(+), 42 deletions(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
> > index 6debda9..d8696d2 100644
> > --- a/drivers/mmc/host/sdhci-s3c.c
> > +++ b/drivers/mmc/host/sdhci-s3c.c
> > @@ -27,6 +27,7 @@
> >
> > #include <linux/pm_runtime.h>
> >
> > #include <linux/mmc/host.h>
> >
> > +#include <linux/mmc/slot-gpio.h>
> >
> > #include "sdhci-s3c-regs.h"
> > #include "sdhci.h"
> >
> > @@ -400,44 +401,6 @@ static void sdhci_s3c_notify_change(struct
> > platform_device *dev, int state)
> >
> > }
> >
> > }
> >
> > -static irqreturn_t sdhci_s3c_gpio_card_detect_thread(int irq, void
> > *dev_id) -{
> > - struct sdhci_s3c *sc = dev_id;
> > - int status = gpio_get_value(sc->ext_cd_gpio);
> > - if (sc->pdata->ext_cd_gpio_invert)
> > - status = !status;
> > - sdhci_s3c_notify_change(sc->pdev, status);
> > - return IRQ_HANDLED;
> > -}
> > -
> > -static void sdhci_s3c_setup_card_detect_gpio(struct sdhci_s3c *sc)
> > -{
> > - struct s3c_sdhci_platdata *pdata = sc->pdata;
> > - struct device *dev = &sc->pdev->dev;
> > -
> > - if (devm_gpio_request(dev, pdata->ext_cd_gpio, "SDHCI EXT CD") == 0)
{
> > - sc->ext_cd_gpio = pdata->ext_cd_gpio;
> > - sc->ext_cd_irq = gpio_to_irq(pdata->ext_cd_gpio);
> > - if (sc->ext_cd_irq &&
> > - request_threaded_irq(sc->ext_cd_irq, NULL,
> > - sdhci_s3c_gpio_card_detect_thread,
> > - IRQF_TRIGGER_RISING |
> > - IRQF_TRIGGER_FALLING |
> > - IRQF_ONESHOT,
> > - dev_name(dev), sc) == 0) {
> > - int status = gpio_get_value(sc->ext_cd_gpio);
> > - if (pdata->ext_cd_gpio_invert)
> > - status = !status;
> > - sdhci_s3c_notify_change(sc->pdev, status);
> > - } else {
> > - dev_warn(dev, "cannot request irq for card detect\n");
> > - sc->ext_cd_irq = 0;
> > - }
> > - } else {
> > - dev_err(dev, "cannot request gpio for card detect\n");
> > - }
> > -}
> > -
> >
> > #ifdef CONFIG_OF
> > static int sdhci_s3c_parse_dt(struct device *dev,
> >
> > struct sdhci_host *host, struct s3c_sdhci_platdata *pdata)
> >
> > @@ -699,8 +662,14 @@ static int sdhci_s3c_probe(struct platform_device
> > *pdev)
> >
> > if (pdata->cd_type == S3C_SDHCI_CD_EXTERNAL && pdata->ext_cd_init)
> >
> > pdata->ext_cd_init(&sdhci_s3c_notify_change);
> >
> > if (pdata->cd_type == S3C_SDHCI_CD_GPIO &&
> >
> > - gpio_is_valid(pdata->ext_cd_gpio))
> > - sdhci_s3c_setup_card_detect_gpio(sc);
> > + gpio_is_valid(pdata->ext_cd_gpio)) {
> > + ret = mmc_gpio_request_cd(host->mmc, pdata->ext_cd_gpio, 0);
> > + if (ret) {
> > + dev_err(dev,
> > + "failed to request card detect gpio\n");
> > + goto err_req_cd;
> > + }
> > + }
> >
> > #ifdef CONFIG_PM_RUNTIME
> >
> > if (pdata->cd_type != S3C_SDHCI_CD_INTERNAL)
> >
> > @@ -708,6 +677,9 @@ static int sdhci_s3c_probe(struct platform_device
> > *pdev)
> >
> > #endif
> >
> > return 0;
> >
> > + err_req_cd:
> > + mmc_gpio_free_cd(host->mmc);
> > +
> >
> > err_req_regs:
> > #ifndef CONFIG_PM_RUNTIME
> >
> > clk_disable_unprepare(sc->clk_bus[sc->cur_clk]);
> >
> > @@ -731,8 +703,8 @@ static int sdhci_s3c_remove(struct platform_device
> > *pdev)
> >
> > if (pdata->cd_type == S3C_SDHCI_CD_EXTERNAL && pdata-
>ext_cd_cleanup)
> >
> > pdata->ext_cd_cleanup(&sdhci_s3c_notify_change);
> >
> > - if (sc->ext_cd_irq)
> > - free_irq(sc->ext_cd_irq, sc);
> > + if (pdata->ext_cd_gpio)
> > + mmc_gpio_free_cd(host->mmc);
> >
> > #ifdef CONFIG_PM_RUNTIME
> >
> > if (pdata->cd_type != S3C_SDHCI_CD_INTERNAL)
prev parent reply other threads:[~2013-11-18 20:03 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-11-05 11:48 [PATCH v2] mmc: sdhci-s3c: Use mmc_gpio_request_cd fuction Beomho Seo
2013-11-18 5:15 ` Jaehoon Chung
2013-11-18 20:03 ` Heiko Stübner [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201311182103.17626.heiko@sntech.de \
--to=heiko@sntech.de \
--cc=beomho.seo@samsung.com \
--cc=cjb@laptop.org \
--cc=jh80.chung@samsung.com \
--cc=linux-mmc@vger.kernel.org \
--cc=myungjoo.ham@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox