From: Jaehoon Chung <jh80.chung@samsung.com>
To: Girish K S <girish.shivananjappa@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>,
linux-mmc@vger.kernel.org, cjb@laptop.org, kgene.kim@samsung.com,
patches@linaro.org, linux-samsung-soc@vger.kernel.org
Subject: Re: [PATCH V7] mmc: core: Add Power Off Notify Feature eMMC 4.5
Date: Tue, 04 Oct 2011 20:16:09 +0900 [thread overview]
Message-ID: <4E8AEAF9.6080206@samsung.com> (raw)
In-Reply-To: <CAGxe1ZGktJhouA18kC7wyVbihyb44ZHn7uU+ae4WwnCp0RGsFA@mail.gmail.com>
Hi Girish..
My means if you use host->caps2, i think right that should be define
MMC_CAP2_XXX.
Am i wrong?
Best regards,
Jaehoon Chung
On 10/04/2011 08:03 PM, Girish K S wrote:
> Hello Mr Chung,
>
> Kindly apply my HS200 feature patch before this patch. then it will work fine.
> can you check and let me know if it applies after HS200 patch.
>
> If it can be applied i will modify and resend
> regards
> Girish K S
>
> On 4 October 2011 16:22, Jaehoon Chung <jh80.chung@samsung.com> wrote:
>> Hi Girish..
>>
>> i think this patch didn't base on latest for mmc-next..
>> i commented the below.
>>
>> Regards,
>> Jaehoon Chung
>>
>> On 09/29/2011 07:46 PM, Girish K S wrote:
>>
>>> This patch adds the support for power off notify feature
>>> available in eMMC 4.5 devices.
>>> If the the host has support for this feature, then the
>>> mmc core will notify it to the device by setting the
>>> POWER_OFF_NOTIFICATION byte in the extended csd register
>>> with a value 1(POWER_ON).
>>> For suspend mode short timeout is used, whereas for the
>>> normal poweroff long timeout is used.
>>> This patch is dependent on Seungwon Jeon's patch for
>>> CMD6 timeout.
>>>
>>> Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
>>> ---
>>> Changes in V2:
>>> Adds poweroff notification handling in suspend/normal
>>> Changes in V4:
>>> Updated with review comments of Jeon
>>> Changes in V5:
>>> This patch version fixes the problem with power off
>>> notify function, when called for the first time and
>>> card is not yet initialised.
>>> Changes in V6:
>>> Fixes checkpatch errors. The patches are generated after
>>> rebasing to chris's mmc-next branch.
>>> Changes in V7:
>>> Rebased to chris-mmc/mmc-next branch. merged to patches
>>> to single patch.
>>> drivers/mmc/core/core.c | 37 +++++++++++++++++++++++++++++++++++++
>>> drivers/mmc/core/mmc.c | 22 ++++++++++++++++++++++
>>> drivers/mmc/host/sdhci.c | 10 ++++++++++
>>> include/linux/mmc/card.h | 21 +++++++++++++++++++++
>>> include/linux/mmc/host.h | 5 +++++
>>> include/linux/mmc/mmc.h | 6 ++++++
>>> 6 files changed, 101 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
>>> index 9698d8a..5fb2120 100644
>>> --- a/drivers/mmc/core/core.c
>>> +++ b/drivers/mmc/core/core.c
>>> @@ -1198,11 +1198,46 @@ static void mmc_power_up(struct mmc_host *host)
>>>
>>> void mmc_power_off(struct mmc_host *host)
>>> {
>>> + struct mmc_card *card;
>>> + unsigned int notify_type;
>>> + unsigned int timeout;
>>> + int err;
>>> +
>>> + BUG_ON(!host);
>>> +
>>> mmc_host_clk_hold(host);
>>>
>>> + card = host->card;
>>> host->ios.clock = 0;
>>> host->ios.vdd = 0;
>>>
>>> + if (card != NULL && mmc_card_mmc(card) &&
>>> + (mmc_card_powernotify_on(card))) {
>>> +
>>> + if (host->power_notify_type == MMC_HOST_PW_NOTIFY_SHORT) {
>>> + notify_type = EXT_CSD_POWER_OFF_SHORT;
>>> + timeout = card->ext_csd.generic_cmd6_time;
>>> + mmc_card_set_powernotify_short(card);
>>> + } else {
>>> + notify_type = EXT_CSD_POWER_OFF_LONG;
>>> + timeout = card->ext_csd.power_off_longtime;
>>> + mmc_card_set_powernotify_long(card);
>>> + }
>>> +
>>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>>> + EXT_CSD_POWER_OFF_NOTIFICATION,
>>> + notify_type, timeout);
>>> +
>>> + if (err && err != -EBADMSG)
>>> + pr_err("Device failed to respond "
>>> + "within %d poweroff time."
>>> + "forcefully powering down"
>>> + "the device\n", timeout);
>>> +
>>> + /* Set the card state to no notification after the poweroff */
>>> + mmc_card_set_powernotify_off(card);
>>> + }
>>> +
>>> /*
>>> * Reset ocr mask to be the highest possible voltage supported for
>>> * this mmc host. This value will be used at next power up.
>>> @@ -2194,6 +2230,7 @@ int mmc_pm_notify(struct notifier_block *notify_block,
>>>
>>> spin_lock_irqsave(&host->lock, flags);
>>> host->rescan_disable = 1;
>>> + host->power_notify_type = MMC_HOST_PW_NOTIFY_SHORT;
>>> spin_unlock_irqrestore(&host->lock, flags);
>>> cancel_delayed_work_sync(&host->detect);
>>>
>>> @@ -2217,6 +2254,7 @@ int mmc_pm_notify(struct notifier_block *notify_block,
>>>
>>> spin_lock_irqsave(&host->lock, flags);
>>> host->rescan_disable = 0;
>>> + host->power_notify_type = MMC_HOST_PW_NOTIFY_LONG;
>>> spin_unlock_irqrestore(&host->lock, flags);
>>> mmc_detect_change(host, 0);
>>>
>>> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
>>> index f28aa4f..25ba7f5 100644
>>> --- a/drivers/mmc/core/mmc.c
>>> +++ b/drivers/mmc/core/mmc.c
>>> @@ -447,6 +447,11 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
>>> else
>>> card->erased_byte = 0x0;
>>>
>>> + if (card->ext_csd.rev >= 6) {
>>> + card->ext_csd.power_off_longtime = 10 *
>>> + ext_csd[EXT_CSD_POWER_OFF_LONG_TIME];
>>> + }
>>> +
>>> out:
>>> return err;
>>> }
>>> @@ -829,6 +834,23 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
>>> }
>>>
>>> /*
>>> + * If the host supports the power_off_notify capability then
>>> + * set the notification byte in the ext_csd register of device
>>> + */
>>> + if (host->caps2 & MMC_CAP_POWEROFF_NOTIFY &&
>>> + (mmc_card_powernotify_off(card))) {
>>> + err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
>>> + EXT_CSD_POWER_OFF_NOTIFICATION,
>>> + EXT_CSD_POWER_ON,
>>> + card->ext_csd.generic_cmd6_time);
>>> + if (err && err != -EBADMSG)
>>> + goto free_card;
>>> + }
>>> +
>>
>>
>> you used host->caps2, i think right that should be use
>> MMC_CAP2_POWEROFF_NOTIFY.
>>
>>> + if (!err)
>>> + mmc_card_set_powernotify_on(card);
>>> +
>>> + /*
>>> * Activate high speed (if supported)
>>> */
>>> if (card->ext_csd.hs_max_dtr != 0) {
>>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>>> index 4220133..2818238 100644
>>> --- a/drivers/mmc/host/sdhci.c
>>> +++ b/drivers/mmc/host/sdhci.c
>>> @@ -2599,6 +2599,16 @@ int sdhci_add_host(struct sdhci_host *host)
>>> if (caps[1] & SDHCI_DRIVER_TYPE_D)
>>> mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
>>>
>>> + /*
>>> + * If Notify capability is enabled and
>>> + * notify type is not initialised by host, set default to
>>> + * long power off notify timeout value
>>> + */
>>> + if (mmc->caps2 & MMC_CAP_POWEROFF_NOTIFY)
>>> + mmc->power_notify_type = MMC_HOST_PW_NOTIFY_SHORT;
>>> + else
>>> + mmc->power_notify_type = MMC_HOST_PW_NOTIFY_NONE;
>>> +
>>
>>
>> also here...
>>
>>> /* Initial value for re-tuning timer count */
>>> host->tuning_count = (caps[1] & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
>>> SDHCI_RETUNING_TIMER_COUNT_SHIFT;
>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
>>> index 15e5ce2..d6f8c85 100644
>>> --- a/include/linux/mmc/card.h
>>> +++ b/include/linux/mmc/card.h
>>> @@ -53,6 +53,8 @@ struct mmc_ext_csd {
>>> u8 rst_n_function;
>>> unsigned int part_time; /* Units: ms */
>>> unsigned int sa_timeout; /* Units: 100ns */
>>> + unsigned int generic_cmd6_time; /* Units: ms */
>>> + unsigned int power_off_longtime; /* Units: ms */
>>> unsigned int hs_max_dtr;
>>> unsigned int sectors;
>>> unsigned int card_type;
>>> @@ -192,6 +194,11 @@ struct mmc_card {
>>> #define MMC_QUIRK_BLK_NO_CMD23 (1<<7) /* Avoid CMD23 for regular multiblock */
>>> #define MMC_QUIRK_BROKEN_BYTE_MODE_512 (1<<8) /* Avoid sending 512 bytes in */
>>> /* byte mode */
>>> + unsigned int poweroff_notify_state; /* eMMC4.5 notify feature */
>>> +#define MMC_NO_POWER_NOTIFICATION 0
>>> +#define MMC_POWERED_ON 1
>>> +#define MMC_POWEROFF_SHORT 2
>>> +#define MMC_POWEROFF_LONG 3
>>>
>>> unsigned int erase_size; /* erase size in sectors */
>>> unsigned int erase_shift; /* if erase unit is power 2 */
>>> @@ -329,6 +336,20 @@ static inline void __maybe_unused remove_quirk(struct mmc_card *card, int data)
>>> #define mmc_sd_card_set_uhs(c) ((c)->state |= MMC_STATE_ULTRAHIGHSPEED)
>>> #define mmc_card_set_ext_capacity(c) ((c)->state |= MMC_CARD_SDXC)
>>>
>>> +#define mmc_card_powernotify_on(c) \
>>> + ((c)->poweroff_notify_state == MMC_POWERED_ON)
>>> +#define mmc_card_powernotify_off(c) \
>>> + ((c)->poweroff_notify_state == MMC_NO_POWER_NOTIFICATION)
>>> +
>>> +#define mmc_card_set_powernotify_off(c) \
>>> + ((c)->poweroff_notify_state = MMC_NO_POWER_NOTIFICATION)
>>> +#define mmc_card_set_powernotify_on(c) \
>>> + ((c)->poweroff_notify_state = MMC_POWERED_ON)
>>> +#define mmc_card_set_powernotify_short(c) \
>>> + ((c)->poweroff_notify_state = MMC_POWEROFF_SHORT)
>>> +#define mmc_card_set_powernotify_long(c) \
>>> + ((c)->poweroff_notify_state = MMC_POWEROFF_LONG)
>>> +
>>> /*
>>> * Quirk add/remove for MMC products.
>>> */
>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
>>> index f62ffa2..b711a00 100644
>>> --- a/include/linux/mmc/host.h
>>> +++ b/include/linux/mmc/host.h
>>> @@ -245,8 +245,13 @@ struct mmc_host {
>>> #define MMC_CAP_HS200_1_8V_SDR (1 << 2) /* can support */
>>> #define MMC_CAP_HS200_1_2V_SDR (1 << 3) /* can support */
>>> #define MMC_CAP_HIGHSPEED_200 (1 << 4) /* Can do MMC HS200 timing */
>>> +#define MMC_CAP_POWEROFF_NOTIFY (1 << 31) /* Notify poweroff supported */
>>>
>>> mmc_pm_flag_t pm_caps; /* supported pm features */
>>> + unsigned int power_notify_type;
>>> +#define MMC_HOST_PW_NOTIFY_NONE 0
>>> +#define MMC_HOST_PW_NOTIFY_SHORT 1
>>> +#define MMC_HOST_PW_NOTIFY_LONG 2
>>>
>>> #ifdef CONFIG_MMC_CLKGATE
>>> int clk_requests; /* internal reference counter */
>>> diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
>>> index 3f2e210..944c99b 100644
>>> --- a/include/linux/mmc/mmc.h
>>> +++ b/include/linux/mmc/mmc.h
>>> @@ -271,6 +271,7 @@ struct _mmc_csd {
>>> * EXT_CSD fields
>>> */
>>>
>>> +#define EXT_CSD_POWER_OFF_NOTIFICATION 34 /* R/W */
>>> #define EXT_CSD_PARTITION_ATTRIBUTE 156 /* R/W */
>>> #define EXT_CSD_PARTITION_SUPPORT 160 /* RO */
>>> #define EXT_CSD_RST_N_FUNCTION 162 /* R/W */
>>> @@ -348,6 +349,11 @@ struct _mmc_csd {
>>> #define EXT_CSD_RST_N_EN_MASK 0x3
>>> #define EXT_CSD_RST_N_ENABLED 1 /* RST_n is enabled on card */
>>>
>>> +#define EXT_CSD_NO_POWER_NOTIFICATION 0
>>> +#define EXT_CSD_POWER_ON 1
>>> +#define EXT_CSD_POWER_OFF_SHORT 2
>>> +#define EXT_CSD_POWER_OFF_LONG 3
>>> +
>>> #define EXT_CSD_PWR_CL_8BIT_MASK 0xF0 /* 8 bit PWR CLS */
>>> #define EXT_CSD_PWR_CL_4BIT_MASK 0x0F /* 8 bit PWR CLS */
>>> #define EXT_CSD_PWR_CL_8BIT_SHIFT 4
>>
>>
>>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
next prev parent reply other threads:[~2011-10-04 11:16 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-09-29 10:46 [PATCH V3] mmc: core: HS200 mode support for eMMC 4.5 Girish K S
2011-09-29 10:46 ` [PATCH V7] mmc: core: Add Power Off Notify Feature " Girish K S
2011-10-04 10:52 ` Jaehoon Chung
2011-10-04 11:03 ` Girish K S
2011-10-04 11:16 ` Jaehoon Chung [this message]
2011-10-04 11:20 ` Girish K S
2011-10-04 11:41 ` Girish K S
2011-10-04 12:12 ` Girish K S
2011-10-04 12:19 ` Jaehoon Chung
2011-10-04 12:43 ` Girish K S
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4E8AEAF9.6080206@samsung.com \
--to=jh80.chung@samsung.com \
--cc=cjb@laptop.org \
--cc=girish.shivananjappa@linaro.org \
--cc=kgene.kim@samsung.com \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=patches@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox