* [PATCH] fsl_ifc_nand: Added dts support for SW BCH ECC @ 2016-09-06 19:32 Matt Weber 2016-09-06 19:55 ` Boris Brezillon 0 siblings, 1 reply; 3+ messages in thread From: Matt Weber @ 2016-09-06 19:32 UTC (permalink / raw) To: linux-mtd; +Cc: boris.brezillon, Dipen.Dudhat, Matt Weber, sgtandel Added "nand-sw-ecc-bch", "nand-sw-ecc-block" and "nand-sw-ecc-strength" properties for software based BCH ECC. So if driver finds these properies in DTS NAND flash node, it disables HW ECC and sets ecc mode to NAND_ECC_SOFT_BCH and initializes ecc params. Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com> Signed-off-by: sgtandel <sanjay.tandel@rockwellcollins.com> --- drivers/mtd/nand/fsl_ifc_nand.c | 32 ++++++++++++++++++++++++++++++-- 1 file changed, 30 insertions(+), 2 deletions(-) diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c index 4e9e5fd..1d74ce5 100644 --- a/drivers/mtd/nand/fsl_ifc_nand.c +++ b/drivers/mtd/nand/fsl_ifc_nand.c @@ -806,7 +806,8 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) struct fsl_ifc_runtime __iomem *ifc_runtime = ctrl->rregs; struct nand_chip *chip = &priv->chip; struct mtd_info *mtd = nand_to_mtd(&priv->chip); - u32 csor; + u32 csor, csor_swecc; + struct device_node *np = priv->dev->of_node; /* Fill in fsl_ifc_mtd structure */ mtd->dev.parent = priv->dev; @@ -879,8 +880,35 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) return -ENODEV; } + /* Independent of u-boot's csor settings, If we have "nand-sw-ecc-bch40" + property set in device tree's nand flash node, enable 40-bit sw bch ecc */ + if (of_property_read_bool(np, "nand-sw-ecc-bch")) { + + csor_swecc = csor & (~CSOR_NAND_ECC_DEC_EN & + ~CSOR_NAND_ECC_ENC_EN & ~CSOR_NAND_ECC_MODE_8); + ifc_out32(csor_swecc, &ifc_global->csor_cs[priv->bank].csor); + chip->ecc.mode = NAND_ECC_SOFT_BCH; + + /* ECC Block */ + if (of_property_read_u32(np, "nand-sw-ecc-block", &chip->ecc.size)) { + dev_warn(priv->dev,"devicetree nand-sw-ecc-block property not found\n"); + chip->ecc.size = 1024; /* ECC block default */ + } + + /* ECC Strength */ + if (of_property_read_u32(np, "nand-sw-ecc-strength", &chip->ecc.strength)) { + dev_warn(priv->dev,"devicetree nand-sw-ecc-strength property not found\n"); + chip->ecc.strength = 40; /* 40-bit ECC */ + } + + /* Enough bytes to store m*t bits */ + chip->ecc.bytes = ((fls(1 + 8 * chip->ecc.size) * chip->ecc.strength) + 7) / 8; + chip->ecc.layout = NULL; + dev_dbg(priv->dev, "NAND_ECC_SOFT_BCH enabled. Strength %d per %d bytes. m*t=%d\n", + chip->ecc.strength, chip->ecc.size, chip->ecc.bytes); + } /* Must also set CSOR_NAND_ECC_ENC_EN if DEC_EN set */ - if (csor & CSOR_NAND_ECC_DEC_EN) { + else if (csor & CSOR_NAND_ECC_DEC_EN) { chip->ecc.mode = NAND_ECC_HW; mtd_set_ooblayout(mtd, &fsl_ifc_ooblayout_ops); -- 1.9.1 ^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH] fsl_ifc_nand: Added dts support for SW BCH ECC 2016-09-06 19:32 [PATCH] fsl_ifc_nand: Added dts support for SW BCH ECC Matt Weber @ 2016-09-06 19:55 ` Boris Brezillon 2016-09-07 5:05 ` Matthew Weber 0 siblings, 1 reply; 3+ messages in thread From: Boris Brezillon @ 2016-09-06 19:55 UTC (permalink / raw) To: Matt Weber; +Cc: linux-mtd, Dipen.Dudhat, sgtandel On Tue, 6 Sep 2016 14:32:37 -0500 Matt Weber <matthew.weber@rockwellcollins.com> wrote: > Added "nand-sw-ecc-bch", "nand-sw-ecc-block" and "nand-sw-ecc-strength" > properties for software based BCH ECC. So if driver finds these > properies in DTS NAND flash node, it disables HW ECC and sets ecc > mode to NAND_ECC_SOFT_BCH and initializes ecc params. Please don't do that. We already have standard properties to select the ECC engine and its config (nand-ecc-mode, nand-ecc-algo, nand-ecc-strength and nand-ecc-step-size). You even don't have to manually parse these properties, all you have to do is test the chip->ecc.mode and chip->ecc.algo after you've called nand_scan_ident(). Based on these values, you can decide to configure/use your ECC engine or let the core initialize the SW ECC engine for you. > > Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com> > Signed-off-by: sgtandel <sanjay.tandel@rockwellcollins.com> > --- > drivers/mtd/nand/fsl_ifc_nand.c | 32 ++++++++++++++++++++++++++++++-- > 1 file changed, 30 insertions(+), 2 deletions(-) > > diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c > index 4e9e5fd..1d74ce5 100644 > --- a/drivers/mtd/nand/fsl_ifc_nand.c > +++ b/drivers/mtd/nand/fsl_ifc_nand.c > @@ -806,7 +806,8 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) > struct fsl_ifc_runtime __iomem *ifc_runtime = ctrl->rregs; > struct nand_chip *chip = &priv->chip; > struct mtd_info *mtd = nand_to_mtd(&priv->chip); > - u32 csor; > + u32 csor, csor_swecc; > + struct device_node *np = priv->dev->of_node; > > /* Fill in fsl_ifc_mtd structure */ > mtd->dev.parent = priv->dev; > @@ -879,8 +880,35 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) > return -ENODEV; > } > > + /* Independent of u-boot's csor settings, If we have "nand-sw-ecc-bch40" > + property set in device tree's nand flash node, enable 40-bit sw bch ecc */ > + if (of_property_read_bool(np, "nand-sw-ecc-bch")) { > + > + csor_swecc = csor & (~CSOR_NAND_ECC_DEC_EN & > + ~CSOR_NAND_ECC_ENC_EN & ~CSOR_NAND_ECC_MODE_8); > + ifc_out32(csor_swecc, &ifc_global->csor_cs[priv->bank].csor); > + chip->ecc.mode = NAND_ECC_SOFT_BCH; > + > + /* ECC Block */ > + if (of_property_read_u32(np, "nand-sw-ecc-block", &chip->ecc.size)) { > + dev_warn(priv->dev,"devicetree nand-sw-ecc-block property not found\n"); > + chip->ecc.size = 1024; /* ECC block default */ > + } > + > + /* ECC Strength */ > + if (of_property_read_u32(np, "nand-sw-ecc-strength", &chip->ecc.strength)) { > + dev_warn(priv->dev,"devicetree nand-sw-ecc-strength property not found\n"); > + chip->ecc.strength = 40; /* 40-bit ECC */ > + } > + > + /* Enough bytes to store m*t bits */ > + chip->ecc.bytes = ((fls(1 + 8 * chip->ecc.size) * chip->ecc.strength) + 7) / 8; > + chip->ecc.layout = NULL; > + dev_dbg(priv->dev, "NAND_ECC_SOFT_BCH enabled. Strength %d per %d bytes. m*t=%d\n", > + chip->ecc.strength, chip->ecc.size, chip->ecc.bytes); > + } > /* Must also set CSOR_NAND_ECC_ENC_EN if DEC_EN set */ > - if (csor & CSOR_NAND_ECC_DEC_EN) { > + else if (csor & CSOR_NAND_ECC_DEC_EN) { > chip->ecc.mode = NAND_ECC_HW; > mtd_set_ooblayout(mtd, &fsl_ifc_ooblayout_ops); > ^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH] fsl_ifc_nand: Added dts support for SW BCH ECC 2016-09-06 19:55 ` Boris Brezillon @ 2016-09-07 5:05 ` Matthew Weber 0 siblings, 0 replies; 3+ messages in thread From: Matthew Weber @ 2016-09-07 5:05 UTC (permalink / raw) To: Boris Brezillon Cc: linux-mtd, Dipen.Dudhat, sgtandel, oss, prabhakar.kushwaha Apologize for top post. Dipen seems to have moved on. Adding new CC(s). Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Cc: Steve Wood <oss@buserror.net> On Tue, Sep 6, 2016 at 2:55 PM, Boris Brezillon <boris.brezillon@free-electrons.com> wrote: > > On Tue, 6 Sep 2016 14:32:37 -0500 > Matt Weber <matthew.weber@rockwellcollins.com> wrote: > > > Added "nand-sw-ecc-bch", "nand-sw-ecc-block" and "nand-sw-ecc-strength" > > properties for software based BCH ECC. So if driver finds these > > properies in DTS NAND flash node, it disables HW ECC and sets ecc > > mode to NAND_ECC_SOFT_BCH and initializes ecc params. > > Please don't do that. We already have standard properties to select the > ECC engine and its config (nand-ecc-mode, nand-ecc-algo, > nand-ecc-strength and nand-ecc-step-size). > > You even don't have to manually parse these properties, all you have to > do is test the chip->ecc.mode and chip->ecc.algo after you've called > nand_scan_ident(). Based on these values, you can decide to > configure/use your ECC engine or let the core initialize the SW ECC > engine for you. > > > > > Signed-off-by: Matthew Weber <matthew.weber@rockwellcollins.com> > > Signed-off-by: sgtandel <sanjay.tandel@rockwellcollins.com> > > --- > > drivers/mtd/nand/fsl_ifc_nand.c | 32 ++++++++++++++++++++++++++++++-- > > 1 file changed, 30 insertions(+), 2 deletions(-) > > > > diff --git a/drivers/mtd/nand/fsl_ifc_nand.c b/drivers/mtd/nand/fsl_ifc_nand.c > > index 4e9e5fd..1d74ce5 100644 > > --- a/drivers/mtd/nand/fsl_ifc_nand.c > > +++ b/drivers/mtd/nand/fsl_ifc_nand.c > > @@ -806,7 +806,8 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) > > struct fsl_ifc_runtime __iomem *ifc_runtime = ctrl->rregs; > > struct nand_chip *chip = &priv->chip; > > struct mtd_info *mtd = nand_to_mtd(&priv->chip); > > - u32 csor; > > + u32 csor, csor_swecc; > > + struct device_node *np = priv->dev->of_node; > > > > /* Fill in fsl_ifc_mtd structure */ > > mtd->dev.parent = priv->dev; > > @@ -879,8 +880,35 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv) > > return -ENODEV; > > } > > > > + /* Independent of u-boot's csor settings, If we have "nand-sw-ecc-bch40" > > + property set in device tree's nand flash node, enable 40-bit sw bch ecc */ > > + if (of_property_read_bool(np, "nand-sw-ecc-bch")) { > > + > > + csor_swecc = csor & (~CSOR_NAND_ECC_DEC_EN & > > + ~CSOR_NAND_ECC_ENC_EN & ~CSOR_NAND_ECC_MODE_8); > > + ifc_out32(csor_swecc, &ifc_global->csor_cs[priv->bank].csor); > > + chip->ecc.mode = NAND_ECC_SOFT_BCH; > > + > > + /* ECC Block */ > > + if (of_property_read_u32(np, "nand-sw-ecc-block", &chip->ecc.size)) { > > + dev_warn(priv->dev,"devicetree nand-sw-ecc-block property not found\n"); > > + chip->ecc.size = 1024; /* ECC block default */ > > + } > > + > > + /* ECC Strength */ > > + if (of_property_read_u32(np, "nand-sw-ecc-strength", &chip->ecc.strength)) { > > + dev_warn(priv->dev,"devicetree nand-sw-ecc-strength property not found\n"); > > + chip->ecc.strength = 40; /* 40-bit ECC */ > > + } > > + > > + /* Enough bytes to store m*t bits */ > > + chip->ecc.bytes = ((fls(1 + 8 * chip->ecc.size) * chip->ecc.strength) + 7) / 8; > > + chip->ecc.layout = NULL; > > + dev_dbg(priv->dev, "NAND_ECC_SOFT_BCH enabled. Strength %d per %d bytes. m*t=%d\n", > > + chip->ecc.strength, chip->ecc.size, chip->ecc.bytes); > > + } > > /* Must also set CSOR_NAND_ECC_ENC_EN if DEC_EN set */ > > - if (csor & CSOR_NAND_ECC_DEC_EN) { > > + else if (csor & CSOR_NAND_ECC_DEC_EN) { > > chip->ecc.mode = NAND_ECC_HW; > > mtd_set_ooblayout(mtd, &fsl_ifc_ooblayout_ops); > > > -- Matthew L Weber / Pr Software Engineer Airborne Information Systems / Security Systems and Software / Secure Platforms MS 131-100, C Ave NE, Cedar Rapids, IA, 52498, USA www.rockwellcollins.com Note: Any Export License Required Information and License Restricted Third Party Intellectual Property (TPIP) content must be encrypted and sent to matthew.weber@corp.rockwellcollins.com. ^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-09-07 5:05 UTC | newest] Thread overview: 3+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2016-09-06 19:32 [PATCH] fsl_ifc_nand: Added dts support for SW BCH ECC Matt Weber 2016-09-06 19:55 ` Boris Brezillon 2016-09-07 5:05 ` Matthew Weber
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox